BIS - LIMS (Laboratory Information Management System)

(Suspended)ATCC TEST LABS LLP

KHASRA NO. 45/6, SITUATED IN THE AREA, VILLAGE PRAHLADPUR BANGER,, North West Delhi, Delhi, 110042, Delhi, North West, Delhi, 110042

9891606632 info@atcctestlabs.com

Scope List

Reset

101 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 1258 (2024)

Bayonet lampholders (Fifth Revision)

22000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(General requirements)	-	1000	-
6(Standard ratings)	-	1000	-
7(Classification)	-	500	-
8(Marking)	-	500	-
9(Dimensions)	-	1000	-
10(Protection against electric shock)	-	1000	-
11(Terminals)	-	1000	-
12(Provision for earthing)	-	1000	-
13(Construction)	-	1000	-
14(Switched lampholders)	-	1000	-
15(Moisture resistance, insulation resistance and electrical strength)	-	1000	-
16(Mechanical strength)	-	1000	-
17(Screws, current-carrying parts and connections)	-	1000	-
18(Creepage distances and clearances)	-	1000	-
19(General resistance to heat)	-	1000	-
20(Resistance to heat, fire and tracking)	-	1000	-
21(Resistance to excessive residual stresses (season cracking) and to rusting)	-	1000	-
Annex A(Season cracking/corrosion test)	-	500	-
12.4(Thermal tests)	-	500	-
9.1(Lampholder dimensions)	-	500	-
11.2(Terminals)	-	500	-
12.3(Provision for earthing)	-	500	-
13.1(Construction)	-	500	-
13.8(Construction)	-	1000	-
14.4(Switched lampholders)	-	500	-
15.1(Moisture resistance, insulation resistance and electrical strength)	-	500	-
16.7(Mechanical strength)	-	300	-
16.8(Mechanical strength)	-	200	-
21.2(Resistance to excessive residual stresses (season cracking) and to rusting)	-	500	-

15 Jun, 2029

-
Included w.e.f 04.07.2025

IS 191 (2007)

Copper - Specification (Fourth Revision)

45000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4-Table 1(GRADES/DESIGNATIONS)	-	1000	For Copper Grade Cu-CATH-1&2 Rs. 25000/-, Grade Cu-ETP &Cu-FRHC Rs.7000/- and Others Grade Rs. 20000/- Each
5.1- Table 2(L)	-	1000	-
5.1- Table 2(L1)	-	1000	-
5.1- Table 2(h)	-	1000	-
5.1- Table 2(h1)	-	1000	-
5.1- Table 2(b)	-	1000	-
5.1- Table 2(b1)	-	1000	-
5.1- Table 2(R)	-	1000	-
5.1- Table 2(R1)	-	1000	-
5.1- Table 2(R2 )	-	1000	-
5.1- Table 2(α )	-	1000	-
5.1- Table 2( β )	-	1000	-
5.1- Table 2(γ)	-	1000	-
5.2(Billets)	-	1000	-
5.4-Table 3 (For Billets)(Mass)	-	1000	-
5.2-Table 3 (For Billets)(Diameter)	-	1000	-
5.2-Table 3 (For Billets)(Length)	-	1000	-
5.2-Table 3 (For Billets)(Deviation from straightness per 1000 mm length)	-	1000	-
5.4-Table 3 (Vertically continuously cast wire bars)(Mass)	-	1000	-
5.3-Table 3 (Vertically continuously cast wire bars)(Width)	-	1000	-
5.3-Table 3 (Vertically continuously cast wire bars)(thickness )	-	1000	-
5.3-Table 3 (Vertically continuously cast wire bars)(Other dimention)	-	1000	-
5.4-Table 3 (Vertically static cast wire bars)(Mass)	-	1000	-
5.3-Table 3 (Vertically static cast wire bars)(Width)	-	1000	-
5.3-Table 3 (Vertically static cast wire bars)(thickness )	-	1000	-
5.3-Table 3 (Vertically static cast wire bars)(Other dimention)	-	1000	-
5.4-Table 3 (Ingots)(Mass)	-	1000	-
5.4-Table 3 (Cast cakes)(Mass)	-	1000	-
5.3-Table 3 (Cast cakes)(Width)	-	1000	-
5.3-Table 3 (Cast cakes)(thickness )	-	1000	-
5.3-Table 3 (Cast cakes)(Deviation from straightness per 1000 mm length)	-	1000	-
7.1 - Table 4(Copper + Silver(By difference)-IS440)	-	5000	-
7.1 - Table 4(Silver- IS 440)	-	5000	-
7.1 - Table 4(Copper (any Silver present to be counted as copper)-IS440)	-	5000	-
7.1 - Table 4(Phosphorus- IS 440)	-	5000	-
7.1 - Table 4(Arsenic- IS440)	-	5000	-
7.1 - Table 4(Antimony-IS440)	-	5000	-
7.1 - Table 4(Bismuth-IS 440)	-	5000	-
7.1 - Table 4(Iron IS 440)	-	5000	-
7.1 - Table 4(Lead IS 440)	-	5000	-
7.1 - Table 4(Nickel IS 440)	-	5000	-
7.1 - Table 4(Oxygen IS 440)	-	5000	-
7.1 - Table 4(Selenium - IS 440)	-	5000	-
7.1 - Table 4(Sulphur- IS 440)	-	5000	-
7.1 - Table 4(Tellurium- IS 440)	-	5000	-
7.1 - Table 4(Tin - IS 440)	-	5000	-
7.1 - Table 4(Znic-IS 440)	-	5000	-
7.1 - Table 4(Selenium + Telluuium- IS 440)	-	5000	-
7.1 - Table 4(Total Impurities- IS 440)	-	5000	-
8.1(FREEDOM FROM DEFECTS)	-	1000	-
8.2(FREEDOM FROM DEFECTS)	-	1000	-
9.1- Table 5(Mass Resistivity- IS 3635)	-	5000	-
10(HYDROGEN EMBRITTLEMENT TEST- IS 191)	-	5000	-
4-Table 1(GRADES/DESIGNATIONS)	-	5000	-
5.1- Table 2(L)	-	1000	-
5.1- Table 2(L1)	-	1000	-
5.1- Table 2(h)	-	1000	-
5.1- Table 2(h1)	-	1000	-
5.1- Table 2(b)	-	1000	-
5.1- Table 2(b1)	-	1000	-
5.1- Table 2(R)	-	1000	-
5.1- Table 2(R1)	-	1000	-
5.1- Table 2(R2 )	-	1000	-
5.1- Table 2(α )	-	1000	-
5.1- Table 2( β )	-	1000	-
5.1- Table 2(γ)	-	1000	-
5.2(Billets)	-	1000	-
5.4-Table 3 (For Billets)(Mass)	-	1000	-
5.2-Table 3 (For Billets)(Diameter)	-	1000	-
5.2-Table 3 (For Billets)(Length)	-	1000	-
5.2-Table 3 (For Billets)(Deviation from straightness per 1000 mm length)	-	1000	-
5.4-Table 3 (Vertically continuously cast wire bars)(Mass)	-	1000	-
5.3-Table 3 (Vertically continuously cast wire bars)(Width)	-	1000	-
5.3-Table 3 (Vertically continuously cast wire bars)(thickness )	-	1000	-
5.3-Table 3 (Vertically continuously cast wire bars)(Other dimention)	-	1000	-
5.4-Table 3 (Vertically static cast wire bars)(Mass)	-	1000	-
5.3-Table 3 (Vertically static cast wire bars)(Width)	-	1000	-
5.3-Table 3 (Vertically static cast wire bars)(thickness )	-	1000	-
5.3-Table 3 (Vertically static cast wire bars)(Other dimention)	-	1000	-
5.4-Table 3 (Ingots)(Mass)	-	1000	-
5.4-Table 3 (Cast cakes)(Mass)	-	1000	-
5.3-Table 3 (Cast cakes)(Width)	-	1000	-
5.3-Table 3 (Cast cakes)(thickness )	-	1000	-
5.3-Table 3 (Cast cakes)(Deviation from straightness per 1000 mm length)	-	1000	-
7.1 - Table 4(Copper + Silver(By difference)-IS440)	-	5000	-
7.1 - Table 4(Silver- IS 440)	-	5000	-
7.1 - Table 4(Copper (any Silver present to be counted as copper)-IS440)	-	5000	-
7.1 - Table 4(Phosphorus- IS 440)	-	5000	-
7.1 - Table 4(Arsenic- IS440)	-	5000	-
7.1 - Table 4(Antimony-IS440)	-	5000	-
7.1 - Table 4(Bismuth-IS 440)	-	5000	-
7.1 - Table 4(Iron IS 440)	-	5000	-
7.1 - Table 4(Lead IS 440)	-	5000	-
7.1 - Table 4(Nickel IS 440)	-	5000	-
7.1 - Table 4(Oxygen IS 440)	-	5000	-
7.1 - Table 4(Selenium - IS 440)	-	5000	-
7.1 - Table 4(Sulphur- IS 440)	-	5000	-
7.1 - Table 4(Tellurium- IS 440)	-	5000	-
7.1 - Table 4(Tin - IS 440)	-	5000	-
7.1 - Table 4(Znic-IS 440)	-	5000	-
7.1 - Table 4(Selenium + Telluuium- IS 440)	-	5000	-
7.1 - Table 4(Total Impurities- IS 440)	-	5000	-
8.1(FREEDOM FROM DEFECTS)	-	1000	-
8.2(FREEDOM FROM DEFECTS)	-	1000	-
9.1- Table 5(Mass Resistivity- IS 3635)	-	5000	-
10(HYDROGEN EMBRITTLEMENT TEST- IS 191)	-	5000	-
9.1 , 9.2 & 10(Resistivity & HYDROGEN EMBRITTLEMENT TEST)	-	5000	-
9.1 , 9.2 & 10(Resistivity & HYDROGEN EMBRITTLEMENT TEST)	-	5000	-
13(Marking)	-	1000	-
13(Marking)	-	1000	-
13(Marking)	-	1000	-
4-Table 1(GRADES/DESIGNATIONS)	-	1000	-
5.1- Table 2(L)	-	1000	-
5.1- Table 2(L1)	-	1000	-
5.1- Table 2(h)	-	1000	-
5.1- Table 2(h1)	-	1000	-
5.1- Table 2(b)	-	1000	-
5.1- Table 2(b1)	-	1000	-
5.1- Table 2(R)	-	1000	-
5.1- Table 2(R1)	-	1000	-
5.1- Table 2(R2 )	-	1000	-
5.1- Table 2(α )	-	1000	-
5.1- Table 2( β )	-	1000	-
5.1- Table 2(γ)	-	1000	-
5.2(Billets)	-	5000	-
5.4-Table 3 (For Billets)(Mass)	-	5000	-
5.2-Table 3 (For Billets)(Diameter)	-	1000	-
5.2-Table 3 (For Billets)(Length)	-	1000	-
5.2-Table 3 (For Billets)(Deviation from straightness per 1000 mm length)	-	2000	-
5.4-Table 3 (Vertically continuously cast wire bars)(Mass)	-	5000	-
5.3-Table 3 (Vertically continuously cast wire bars)(Width)	-	5000	-
5.3-Table 3 (Vertically continuously cast wire bars)(thickness )	-	5000	-
5.3-Table 3 (Vertically continuously cast wire bars)(Other dimention)	-	5000	-
5.4-Table 3 (Vertically static cast wire bars)(Mass)	-	5000	-
5.3-Table 3 (Vertically static cast wire bars)(Width)	-	5000	-
5.3-Table 3 (Vertically static cast wire bars)(thickness )	-	5000	-
5.3-Table 3 (Vertically static cast wire bars)(Other dimention)	-	5000	-
5.4-Table 3 (Ingots)(Mass)	-	1000	-
5.4-Table 3 (Cast cakes)(Mass)	-	1000	-
5.3-Table 3 (Cast cakes)(Width)	-	1000	-
5.3-Table 3 (Cast cakes)(thickness )	-	1000	-
5.3-Table 3 (Cast cakes)(Deviation from straightness per 1000 mm length)	-	5000	-
7.1 - Table 4(Copper + Silver(By difference)-IS440)	-	5000	-
7.1 - Table 4(Silver- IS 440)	-	5000	-
7.1 - Table 4(Copper (any Silver present to be counted as copper)-IS440)	-	5000	-
7.1 - Table 4(Phosphorus- IS 440)	-	5000	-
7.1 - Table 4(Arsenic- IS440)	-	5000	-
7.1 - Table 4(Antimony-IS440)	-	5000	-
7.1 - Table 4(Bismuth-IS 440)	-	5000	-
7.1 - Table 4(Iron IS 440)	-	5000	-
7.1 - Table 4(Lead IS 440)	-	5000	-
7.1 - Table 4(Nickel IS 440)	-	5000	-
7.1 - Table 4(Oxygen IS 440)	-	5000	-
7.1 - Table 4(Selenium - IS 440)	-	5000	-
7.1 - Table 4(Sulphur- IS 440)	-	5000	-
7.1 - Table 4(Tellurium- IS 440)	-	5000	-
7.1 - Table 4(Tin - IS 440)	-	5000	-
7.1 - Table 4(Znic-IS 440)	-	5000	-
7.1 - Table 4(Selenium + Telluuium- IS 440)	-	5000	-
7.1 - Table 4(Total Impurities- IS 440)	-	5000	-
8.1(FREEDOM FROM DEFECTS)	-	2000	-
8.2(FREEDOM FROM DEFECTS)	-	2000	-
9.1- Table 5(Mass Resistivity- IS 3635)	-	5000	-
10(HYDROGEN EMBRITTLEMENT TEST- IS 191)	-	5000	-
4-Table 1(GRADES/DESIGNATIONS)	-	1000	-
5.1- Table 2(L)	-	1000	-
5.1- Table 2(L1)	-	1000	-
5.1- Table 2(h)	-	1000	-
5.1- Table 2(h1)	-	1000	-
5.1- Table 2(b)	-	1000	-
5.1- Table 2(b1)	-	1000	-
5.1- Table 2(R)	-	1000	-
5.1- Table 2(R1)	-	1000	-
5.1- Table 2(R2 )	-	1000	-
5.1- Table 2(α )	-	1000	-
5.1- Table 2( β )	-	1000	-
5.1- Table 2(γ)	-	1000	-
5.2(Billets)	-	1000	-
5.4-Table 3 (For Billets)(Mass)	-	2000	-
5.2-Table 3 (For Billets)(Diameter)	-	2000	-
5.2-Table 3 (For Billets)(Length)	-	1000	-
5.2-Table 3 (For Billets)(Deviation from straightness per 1000 mm length)	-	1000	-
5.4-Table 3 (Vertically continuously cast wire bars)(Mass)	-	1000	-
5.3-Table 3 (Vertically continuously cast wire bars)(Width)	-	5000	-
5.3-Table 3 (Vertically continuously cast wire bars)(thickness )	-	5000	-
5.3-Table 3 (Vertically continuously cast wire bars)(Other dimention)	-	5000	-
5.4-Table 3 (Vertically static cast wire bars)(Mass)	-	5000	-
5.3-Table 3 (Vertically static cast wire bars)(Width)	-	5000	-
5.3-Table 3 (Vertically static cast wire bars)(thickness )	-	5000	-
5.3-Table 3 (Vertically static cast wire bars)(Other dimention)	-	5000	-
5.4-Table 3 (Ingots)(Mass)	-	5000	-
5.4-Table 3 (Cast cakes)(Mass)	-	5000	-
5.3-Table 3 (Cast cakes)(Width)	-	5000	-
5.3-Table 3 (Cast cakes)(thickness )	-	5000	-
5.3-Table 3 (Cast cakes)(Deviation from straightness per 1000 mm length)	-	5000	-
7.1 - Table 4(Copper + Silver(By difference)-IS440)	-	5000	-
7.1 - Table 4(Silver- IS 440)	-	5000	-
7.1 - Table 4(Copper (any Silver present to be counted as copper)-IS440)	-	5000	-
7.1 - Table 4(Phosphorus- IS 440)	-	5000	-
7.1 - Table 4(Arsenic- IS440)	-	5000	-
7.1 - Table 4(Antimony-IS440)	-	5000	-
7.1 - Table 4(Bismuth-IS 440)	-	5000	-
7.1 - Table 4(Iron IS 440)	-	5000	-
7.1 - Table 4(Lead IS 440)	-	5000	-
7.1 - Table 4(Nickel IS 440)	-	5000	-
7.1 - Table 4(Oxygen IS 440)	-	5000	-
7.1 - Table 4(Selenium - IS 440)	-	5000	-
7.1 - Table 4(Sulphur- IS 440)	-	5000	-
7.1 - Table 4(Tellurium- IS 440)	-	5000	-
7.1 - Table 4(Tin - IS 440)	-	5000	-
7.1 - Table 4(Znic-IS 440)	-	5000	-
7.1 - Table 4(Selenium + Telluuium- IS 440)	-	5000	-
7.1 - Table 4(Total Impurities- IS 440)	-	5000	-
8.1(FREEDOM FROM DEFECTS)	-	1000	-
8.2(FREEDOM FROM DEFECTS)	-	1000	-
9.1- Table 5(Mass Resistivity- IS 3635)	-	5000	-
10(HYDROGEN EMBRITTLEMENT TEST- IS 191)	-	5000	-
9.1 , 9.2 & 10(Resistivity & HYDROGEN EMBRITTLEMENT TEST)	-	5000	-
9.1 , 9.2 & 10(Resistivity & HYDROGEN EMBRITTLEMENT TEST)	-	5000	-
13(Marking)	-	1000	-
13(Marking)	-	1000	-
13(Marking)	-	1000	-

15 Jun, 2029

-
Included w.e.f. 07.08.2025

IS 14494 (2019)

Elastomer insulated flexible cables for use in mines - Specification (First Revision)

150000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(CONDUCTOR)	-	1000	-
5(INSULATION)	-	1000	-
5.1(Power Cores)	-	1000	-
5.2(Pilot and Earth Cores)	-	1000	-
6(SEMI-CONDUCTING COMPOUND)	-	1000	-
7.1(TAPE : Proofed Tape)	-	1000	-
7.2(TAPE : Polyethylene Terephalate (PETP) or Polypropylene Base Tape)	-	1000	-
7.3(TAPE )	-	1000	-
8(CENTRE)	-	1000	-
9.1(FILLERS)	-	1000	-
9.2(FILLERS)	-	1000	-
10(CRADLE SEPARATOR)	-	1000	-
11.1(ARMOUR)	-	1000	-
11.2(ARMOUR)	-	1000	-
11.2 a)(ARMOURING: Tensile Strength)	-	2000	-
11.2 b)(ARMOURING: Elongation )	-	2000	-
11.2 c)(ARMOURING: Torsion Test (For round wire ) )	-	2000	-
11.2 d)(ARMOURING: Uniformity of zinc coating)	-	2000	-
11.2 e)(ARMOURING: Mass of zinc coating )	-	2000	-
12.1(SHEATH : Inner Sheath)	-	1000	-
12.2(SHEATH : Outer Sheath)	-	1000	-
13.1(REINFORCEMENT MATERIAL : Tape)	-	1000	-
13.2(REINFORCEMENT MATERIAL : Cord/Yarns)	-	1000	-
14.1(CONSTRUCTION : CONDUCTOR)	-	1000	-
14.2(CONSTRUCTION : CONDUCTOR)	-	1000	-
14.3(CONSTRUCTION : CONDUCTOR)	-	1000	-
14.4(CONSTRUCTION : CONDUCTOR)	-	1000	-
15(CONDUCTOR SCREENING)	-	1000	-
16.1(INSULATION)	-	1000	-
16.2(INSULATION : Thickness of Insulation)	-	2000	-
16.3(INSULATION : Tolerance on Insulation Thickness)	-	2000	-
16.4(INSULATION : Application of Insulation)	-	1000	-
16.5(INSULATION)	-	1000	-
17.1(INSULATION SCREEN)	-	1000	-
17.2(INSULATION SCREEN)	-	1000	-
17.3(INSULATION SCREEN)	-	1000	-
17.4(INSULATION SCREEN)	-	1000	-
18(PROTECTIVE SCREEN)	-	1000	-
19(CONDUCTANCE OF SCREEN)	-	1000	-
19.1(Individual Core Screen)	-	1000	-
19.2(Collective Screen)	-	1000	-
20.1(CORE IDENTIFICATION)	-	1000	-
20.2(Colour Scheme for Identification)	-	1000	-
20.3(Scheme for Identification by Numbering)	-	1000	-
21.1(LAYING UP OF CORES)	-	1000	-
21.2(LAYING UP OF CORES)	-	1000	-
21.3(LAYING UP OF CORES)	-	1000	-
21.4(LAYING UP OF CORES)	-	1000	-
22.1(INNER SHEATH)	-	1000	-
22.2(Thickness of Inner Sheath)	-	2000	-
22.3(INNER SHEATH)	-	1000	-
23.1(ARMOURING)	-	1000	-
23.2(ARMOURING)	-	1000	-
23.3(ARMOURING)	-	1000	-
23.4(ARMOURING)	-	1000	-
24.1(OUTER SHEATH)	-	1000	-
24.2(Thickness of Outer Sheath)	-	2000	-
24.3(Tolerance on Thickness of Outer Sheath)	-	2000	-
24.4(OUTER SHEATH)	-	1000	-
25.1(CABLE CONSTRUCTION AND DIMENSIONS)	-	2000	-
27.2(Bending test followed by partial discharge test;)	-	0	-
27.4(Dielectric power factor test)	-	0	-
27.5(Heating cycle test followed by partial discharge test;)	-	0	-
27.6(Impulse voltage test; and)	-	0	-
26.3(Special Provisions)	-	1000	-
27.8(Flammability Test)	-	2000	-
27.9(Water Absorption Test)	-	5000	-
28(IDENTIFICATION)	-	1000	-
29.1(PACKING AND MARKING)	-	1000	-
29.2(PACKING AND MARKING)	-	1000	-
30(BIS CERTIFICATION MARKING)	-	1000	-
Table 33®, Annex E(Electric tset on semi-conducting screen)	-	10000	-
Table 33(n), Cl. No. 27.7(High Voltage test for 4 hrs.)	-	10000	-
Table 33(j), Cl. No. 27.4(Dielectric Power Factor (as a function of Voltage))	-	0	-
Table 33(h), Cl. No. 27.2(Partial discharge test)	-	0	-
Table 33(f)(Insulation resistance)	-	10000	-
Table 33(e)(Tear resistance on sheath)	-	2000	-
Table 33(e)(Oil resistance - Elongation on sheath)	-	5000	-
Table 33(e)(Oil resistance - Tensile strength on sheath)	-	5000	-
Table 33(e)(Permanent set on Sheath)	-	2000	-
Table 33(e)(Hot set on Sheath)	-	2000	-
Table 33(e)(Ageing in air bomb - Elongation on Sheath)	-	5000	-
Table 33(e)(Ageing in air bomb - Tensile strength on Sheath)	-	5000	-
Table 33(e)(Elongation at break on Sheath)	-	2000	-
Table 33(e)(Tensile strength on Sheath)	-	2000	-
Table 33(d)(Ozone resistance on Insulation)	-	5000	-
Table 33(d)(Permanent set on Insulation)	-	2000	-
Table 33(d)(Hot set on Insulation)	-	2000	-
Table 33(d)(Ageing in air bomb - Elongation on Insulation)	-	5000	-
Table 33(d)(Ageing in air bomb - Tensile strength on Insulation)	-	5000	-
Table 33(d)(Ageing in air oven - Elongation on Insulation)	-	5000	-
Table 33(d)(Ageing in air oven - Tensile strength on Insulation)	-	5000	-
Table 33(d)(Elongation at break on Insulation)	-	2000	-
Table 33(d)(Tensile strength on Insulation)	-	2000	-
Table 33(c)(Resistivity of steel wire)	-	2000	-
Table 33(b)(Diameter of armour wire)	-	2000	-
Table 4(Copper purity test)	-	10000	-
Table 33(a)(Conductor resistance test)	-	2000	-
Table 33(a)(Annealing test)	-	2000	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath ( Without ageing))	-	2000	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath ( Without ageing))	-	2000	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath ( Without ageing))	-	2000	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath ( After ageing in air bomb)	-	2000	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath ( After ageing in air bomb)	-	2000	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath (Oil resistance test ))	-	2000	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath)	-	2000	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath (Hot set test))	-	2000	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath (Hot set test))	-	2000	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath (Hot set test))	-	2000	-
[ Table 2 of IS:6380-1984](Insulation resistance constant)	-	2000	-
[ Table 2 of IS:6380-1984](Insulation resistance constant)	-	2000	-
[ Cl.5 & Table 2 of IS:6380-1984](Physical tests on Outer Sheath ( Without ageing))	-	2000	-
[ Cl.5 & Table 2 of IS:6380-1984](Physical tests on Outer Sheath ( Without ageing))	-	2000	-
[ Cl.5 & Table 2 of IS:6380-1984](Physical tests on insulation (After ageing in air oven:))	-	2000	-
[ Cl.5 & Table 2 of IS:6380-1984](Physical tests on insulation (After ageing in air oven:))	-	2000	-
[ Cl.5 & Table 2 of IS:6380-1984](Physical tests on insulation (After ageing in air bomb ))	-	2000	-
[ Cl.5 & Table 2 of IS:6380-1984](Physical tests on insulation (After ageing in air bomb ))	-	2000	-
[ Cl.5 & Table 2 of IS:6380-1984](Physical tests on Insulation (Hot set test))	-	2000	-
[ Cl.5 & Table 2 of IS:6380-1984](Physical tests on Insulation (Hot set test))	-	2000	-
[ Cl.4 & 14](Conductor)	-	1000	-
[ Cl.4 & 14](Conductor)	-	1000	-
[ Cl.4 & 14](Conductor)	-	1000	-
[ Cl.4 & 14](Conductor)	-	1000	-
[ Cl.4 & 14](Conductor)	-	1000	-
[ Cl.4 & 14](Conductor)	-	1000	-
[ Cl.4 & 14](Conductor)	-	1000	-
[Cl.14.4](Conductor)	-	1000	-
Cl. 27.7(High voltage test for 4 hours)	-	10000	-
4(CONDUCTOR)	-	0	-
5(INSULATION)	-	0	-
5.1(Power Cores)	-	0	-
5.2(Pilot and Earth Cores)	-	0	-
6(SEMI-CONDUCTING COMPOUND)	-	0	-
7.1(TAPE : Proofed Tape)	-	0	-
7.2(TAPE : Polyethylene Terephalate (PETP) or Polypropylene Base Tape)	-	0	-
7.3(TAPE )	-	0	-
8(CENTRE)	-	0	-
9.1(FILLERS)	-	0	-
9.2(FILLERS)	-	0	-
10(CRADLE SEPARATOR)	-	0	-
11.1(ARMOUR)	-	0	-
11.2(ARMOUR)	-	0	-
11.2 a)(ARMOURING: Tensile Strength)	-	0	-
11.2 b)(ARMOURING: Elongation )	-	0	-
11.2 c)(ARMOURING: Torsion Test (For round wire ) )	-	0	-
11.2 d)(ARMOURING: Uniformity of zinc coating)	-	0	-
11.2 e)(ARMOURING: Mass of zinc coating )	-	0	-
12.1(SHEATH : Inner Sheath)	-	0	-
12.2(SHEATH : Outer Sheath)	-	0	-
13.1(REINFORCEMENT MATERIAL : Tape)	-	0	-
13.2(REINFORCEMENT MATERIAL : Cord/Yarns)	-	0	-
14.1(CONSTRUCTION : CONDUCTOR)	-	0	-
14.2(CONSTRUCTION : CONDUCTOR)	-	0	-
14.3(CONSTRUCTION : CONDUCTOR)	-	0	-
14.4(CONSTRUCTION : CONDUCTOR)	-	0	-
15(CONDUCTOR SCREENING)	-	0	-
16.1(INSULATION)	-	0	-
16.2(INSULATION : Thickness of Insulation)	-	0	-
16.3(INSULATION : Tolerance on Insulation Thickness)	-	0	-
16.4(INSULATION : Application of Insulation)	-	0	-
16.5(INSULATION)	-	0	-
17.1(INSULATION SCREEN)	-	0	-
17.2(INSULATION SCREEN)	-	0	-
17.3(INSULATION SCREEN)	-	0	-
17.4(INSULATION SCREEN)	-	0	-
18(PROTECTIVE SCREEN)	-	0	-
19(CONDUCTANCE OF SCREEN)	-	0	-
19.1(Individual Core Screen)	-	0	-
19.2(Collective Screen)	-	0	-
20.1(CORE IDENTIFICATION)	-	0	-
20.2(Colour Scheme for Identification)	-	0	-
20.3(Scheme for Identification by Numbering)	-	0	-
21.1(LAYING UP OF CORES)	-	0	-
21.2(LAYING UP OF CORES)	-	0	-
21.3(LAYING UP OF CORES)	-	0	-
21.4(LAYING UP OF CORES)	-	0	-
22.1(INNER SHEATH)	-	0	-
22.2(Thickness of Inner Sheath)	-	0	-
22.3(INNER SHEATH)	-	0	-
23.1(ARMOURING)	-	0	-
23.2(ARMOURING)	-	0	-
23.3(ARMOURING)	-	0	-
23.4(ARMOURING)	-	0	-
24.1(OUTER SHEATH)	-	0	-
24.2(Thickness of Outer Sheath)	-	0	-
24.3(Tolerance on Thickness of Outer Sheath)	-	0	-
24.4(OUTER SHEATH)	-	0	-
25.1(CABLE CONSTRUCTION AND DIMENSIONS)	-	0	-
27.2(Bending test followed by partial discharge test;)	-	0	-
27.4(Dielectric power factor test)	-	0	-
27.5(Heating cycle test followed by partial discharge test;)	-	0	-
27.6(Impulse voltage test; and)	-	0	-
26.3(Special Provisions)	-	0	-
27.8(Flammability Test)	-	0	-
27.9(Water Absorption Test)	-	0	-
28(IDENTIFICATION)	-	0	-
29.1(PACKING AND MARKING)	-	0	-
29.2(PACKING AND MARKING)	-	0	-
30(BIS CERTIFICATION MARKING)	-	0	-
Table 33®, Annex E(Electric tset on semi-conducting screen)	-	0	-
Table 33(n), Cl. No. 27.7(High Voltage test for 4 hrs.)	-	0	-
Table 33(j), Cl. No. 27.4(Dielectric Power Factor (as a function of Voltage))	-	0	-
Table 33(h), Cl. No. 27.2(Partial discharge test)	-	0	-
Table 33(f)(Insulation resistance)	-	0	-
Table 33(e)(Tear resistance on sheath)	-	0	-
Table 33(e)(Oil resistance - Elongation on sheath)	-	0	-
Table 33(e)(Oil resistance - Tensile strength on sheath)	-	0	-
Table 33(e)(Permanent set on Sheath)	-	0	-
Table 33(e)(Hot set on Sheath)	-	0	-
Table 33(e)(Ageing in air bomb - Elongation on Sheath)	-	0	-
Table 33(e)(Ageing in air bomb - Tensile strength on Sheath)	-	0	-
Table 33(e)(Elongation at break on Sheath)	-	0	-
Table 33(e)(Tensile strength on Sheath)	-	0	-
Table 33(d)(Ozone resistance on Insulation)	-	0	-
Table 33(d)(Permanent set on Insulation)	-	0	-
Table 33(d)(Hot set on Insulation)	-	0	-
Table 33(d)(Ageing in air bomb - Elongation on Insulation)	-	0	-
Table 33(d)(Ageing in air bomb - Tensile strength on Insulation)	-	0	-
Table 33(d)(Ageing in air oven - Elongation on Insulation)	-	0	-
Table 33(d)(Ageing in air oven - Tensile strength on Insulation)	-	0	-
Table 33(d)(Elongation at break on Insulation)	-	0	-
Table 33(d)(Tensile strength on Insulation)	-	0	-
Table 33(c)(Resistivity of steel wire)	-	0	-
Table 33(b)(Diameter of armour wire)	-	0	-
Table 4(Copper purity test)	-	0	-
Table 33(a)(Conductor resistance test)	-	0	-
Table 33(a)(Annealing test)	-	0	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath ( Without ageing))	-	0	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath ( Without ageing))	-	0	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath ( Without ageing))	-	0	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath ( After ageing in air bomb)	-	0	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath ( After ageing in air bomb)	-	0	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath (Oil resistance test ))	-	0	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath)	-	0	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath (Hot set test))	-	0	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath (Hot set test))	-	0	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath (Hot set test))	-	0	-
[ Table 2 of IS:6380-1984](Insulation resistance constant)	-	0	-
[ Table 2 of IS:6380-1984](Insulation resistance constant)	-	0	-
[ Cl.5 & Table 2 of IS:6380-1984](Physical tests on Outer Sheath ( Without ageing))	-	0	-
[ Cl.5 & Table 2 of IS:6380-1984](Physical tests on Outer Sheath ( Without ageing))	-	0	-
[ Cl.5 & Table 2 of IS:6380-1984](Physical tests on insulation (After ageing in air oven:))	-	0	-
[ Cl.5 & Table 2 of IS:6380-1984](Physical tests on insulation (After ageing in air oven:))	-	0	-
[ Cl.5 & Table 2 of IS:6380-1984](Physical tests on insulation (After ageing in air bomb ))	-	0	-
[ Cl.5 & Table 2 of IS:6380-1984](Physical tests on insulation (After ageing in air bomb ))	-	0	-
[ Cl.5 & Table 2 of IS:6380-1984](Physical tests on Insulation (Hot set test))	-	0	-
[ Cl.5 & Table 2 of IS:6380-1984](Physical tests on Insulation (Hot set test))	-	0	-
[ Cl.4 & 14](Conductor)	-	0	-
[ Cl.4 & 14](Conductor)	-	0	-
[ Cl.4 & 14](Conductor)	-	0	-
[ Cl.4 & 14](Conductor)	-	0	-
[ Cl.4 & 14](Conductor)	-	0	-
[ Cl.4 & 14](Conductor)	-	0	-
[ Cl.4 & 14](Conductor)	-	0	-
[Cl.14.4](Conductor)	-	0	-
Cl. 27.7(High voltage test for 4 hours)	-	0	-

15 Jun, 2029

-
included w.e.f 09-12-2025

IS 17505 : Part 1 (2021)

Specification for Thermosetting Insulated Fire Survival Cables for Fixed Installation having Low Emission of Smoke and Corrosive Gases when Affected by Fire for Working Voltages upto and including 1100 Vac and 1500 Vdc

140000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 7.3, Table 1 to 5 of IS 8130:2013 & IS:10810 (Part 5)-1984(Conductor Resistance Test)	-	1000	-
Cl. 7.1.2 of IS 8130 : 2013 & IS:10810 (Part 1)-1984(Annealing Test (for copper))	-	1000	-
Cl. 7.1.1 of IS 8130:2013 & IS:10810 (Part 4)-1984(Persulphate Test for tinned copper)	-	3000	-
IS 191:2007 & IS 440(Copper purity test)	-	10000	-
Cl. 11,14,16, Table 4 and Table 6 of IS 17505 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	5000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 36)-1984(Diameter of armour Wire)	-	5000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 37)-1984(Tensile strength and elongation at break)	-	5000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 38)-1984(Torsion Test on galvanised steel wire for armouring)	-	5000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 39)-1984(Winding Test for Formed Wires)	-	5000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 40)-1984(Uniformity of Zinc coating on Round Steel Wires and Formed Steel Wires (Strips))	-	5000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 41)-1984(Mass of Zinc coating on Round Steel Wires and Formed Steel Wires (Strips))	-	5000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 42)-1984(Resistivity test)	-	5000	-
Table 1 and Table 2 of IS 17505 -1: 2021, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	5000	-
Cl 18.2 of IS 17505-1:2021 & IS:10810 (Part 45)-1984(High voltage test)	-	5000	-
Table 1 of IS 17505-1 :2021 & IS:10810 (Part 43)-1984(Insulation Resistance)	-	5000	-
Cl. 18.6 of IS 17505-1:2021 & IS:10810 (Part 58)-1998(Oxygen index)	-	5000	-
Cl. 18.7 of IS 17505-1:2021 & IS:10810 (Part 64)-2003(Temperature Index)	-	5000	-
Table-1 & Table-2 of IS 17505-1:2021 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	5000	-
Specification for thermosetting insulated fire survival cables for fixed installation having low emission of smoke and corrosive gases when affected by fire for working voltages upto and including 1100 V A.C. and 1500 V D.C(Hot deformation)	-	5000	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	10000	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	10000	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	10000	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	10000	-
Table 1 of IS 17505-1: 2021 & IS:10810 (Part 21)-1984(Cold impact test)	-	2000	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 30)-1984(Hot set test)	-	2000	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 13)-1984(Ozone Resistance test)	-	5000	-
Cl 18.5.1 of IS 17505-1 :2021 & IS:10810 (Part 61)-1988(Flame test on single cable)	-	2000	-
Table 1 of IS 17505-1:2021 & IS:10810 (Part 12)-1984(Shrinkage test)	-	2000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	10000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	10000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	10000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	10000	-
Tabel 1 and 2 of IS 17505-1:2021 & IS:10810 (Part 7)-1984(Tensile strength and elongation at break.)	-	10000	-
Tabel 1 and 2 of IS 17505-1:2021 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	10000	-
Cl 18.6 of IS 17505-1: 2021 & IS:10810 (Part 58)-1998(Oxygen Index.)	-	5000	-
Cl 18.8 of IS 17505-1:2021 & IS:10810 (Part 64)-2003(Temperature Index)	-	5000	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 13)-1984(Ozone resistance test)	-	5000	-
Table 2 of IS 17505-1:2021 & IS:10810 (Part 15)-1984(Hot deformation)	-	2000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	10000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	10000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	10000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	10000	-
Table 1 of IS 17505-1:2021 & IS:10810 (Part 12)-1984(Shrinkage test)	-	2000	-
Cl 18.2of IS 17505-1:2021 & IS:10810 (Part 45)-1984.(High Voltage test.)	-	2000	-
Cl 18.5of IS 17505-1:2021 & IS:10810 (Part 53)-1984(Flammability Test)	-	2000	-
Table-2 of IS 17505-1:2021 & IS:10810 (Part 20)-1984(Cold bend test)	-	2000	-
Table-2 of IS 17505-1:2021 & IS:10810 (Part 21)-1984(Cold impact test)	-	2000	-
Cl 18.5 of IS 17505-1:2021 & IS:10810 (Part 61)-1988(Flammability Test)	-	2000	-
Cl 18.9 of IS 17505-1:2021(Water immersion test ( effect of water on sheath of cable))	-	2000	-
Cl 18.8 of IS 17505-1:2021& IS:10810 (Part 63)-1993(Smoke density test)	-	10000	-
Cl. 3.5, 18.4 & Annex-E of IS 17505-1:2021(Circuit integrity test under fire)	-	50000	-
Cl. 17.1 Table 9 (iv) e(Heat Shock)	-	2000	-
Cl. 17.1 Table 9 (iv) h(Water absorption (Gravimetric))	-	5000	-
Cl. 17.1 Table 9 (vii) b(Flame test on bunched cable)	-	20000	-
Cl. 17.1 Table 9 (ix)(Abrasion resistance test)	-	5000	-
Cl. 17.1 Table 9 (iv) m(Assessment of Halogen (HCl))	-	5000	-
Cl. 7.3, Table 1 to 5 of IS 8130:2013 & IS:10810 (Part 5)-1984(Conductor Resistance Test)	-	5000	-
Cl. 7.1.2 of IS 8130 : 2013 & IS:10810 (Part 1)-1984(Annealing Test (for copper))	-	5000	-
Cl. 7.1.1 of IS 8130:2013 & IS:10810 (Part 4)-1984(Persulphate Test for tinned copper)	-	5000	-
IS 191:2007 & IS 440(Copper purity test)	-	8000	-
Cl. 11,14,16, Table 4 and Table 6 of IS 17505 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	5000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 36)-1984(Diameter of armour Wire)	-	5000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 37)-1984(Tensile strength and elongation at break)	-	5000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 38)-1984(Torsion Test on galvanised steel wire for armouring)	-	5000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 39)-1984(Winding Test for Formed Wires)	-	5000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 40)-1984(Uniformity of Zinc coating on Round Steel Wires and Formed Steel Wires (Strips))	-	5000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 41)-1984(Mass of Zinc coating on Round Steel Wires and Formed Steel Wires (Strips))	-	5000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 42)-1984(Resistivity test)	-	5000	-
Table 1 and Table 2 of IS 17505 -1: 2021, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	5000	-
Cl 18.2 of IS 17505-1:2021 & IS:10810 (Part 45)-1984(High voltage test)	-	5000	-
Table 1 of IS 17505-1 :2021 & IS:10810 (Part 43)-1984(Insulation Resistance)	-	5000	-
Cl. 18.6 of IS 17505-1:2021 & IS:10810 (Part 58)-1998(Oxygen index)	-	5000	-
Cl. 18.7 of IS 17505-1:2021 & IS:10810 (Part 64)-2003(Temperature Index)	-	5000	-
Table-1 & Table-2 of IS 17505-1:2021 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	5000	-
Specification for thermosetting insulated fire survival cables for fixed installation having low emission of smoke and corrosive gases when affected by fire for working voltages upto and including 1100 V A.C. and 1500 V D.C(Hot deformation)	-	5000	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	5000	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	5000	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	5000	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	5000	-
Table 1 of IS 17505-1: 2021 & IS:10810 (Part 21)-1984(Cold impact test)	-	5000	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 30)-1984(Hot set test)	-	5000	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 13)-1984(Ozone Resistance test)	-	5000	-
Cl 18.5.1 of IS 17505-1 :2021 & IS:10810 (Part 61)-1988(Flame test on single cable)	-	5000	-
Table 1 of IS 17505-1:2021 & IS:10810 (Part 12)-1984(Shrinkage test)	-	5000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	5000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	5000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	5000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	5000	-
Tabel 1 and 2 of IS 17505-1:2021 & IS:10810 (Part 7)-1984(Tensile strength and elongation at break.)	-	5000	-
Tabel 1 and 2 of IS 17505-1:2021 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	5000	-
Cl 18.6 of IS 17505-1: 2021 & IS:10810 (Part 58)-1998(Oxygen Index.)	-	5000	-
Cl 18.8 of IS 17505-1:2021 & IS:10810 (Part 64)-2003(Temperature Index)	-	5000	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 13)-1984(Ozone resistance test)	-	5000	-
Table 2 of IS 17505-1:2021 & IS:10810 (Part 15)-1984(Hot deformation)	-	5000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	5000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	5000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	5000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	5000	-
Table 1 of IS 17505-1:2021 & IS:10810 (Part 12)-1984(Shrinkage test)	-	5000	-
Cl 18.2of IS 17505-1:2021 & IS:10810 (Part 45)-1984.(High Voltage test.)	-	5000	-
Cl 18.5of IS 17505-1:2021 & IS:10810 (Part 53)-1984(Flammability Test)	-	5000	-
Table-2 of IS 17505-1:2021 & IS:10810 (Part 20)-1984(Cold bend test)	-	5000	-
Table-2 of IS 17505-1:2021 & IS:10810 (Part 21)-1984(Cold impact test)	-	5000	-
Cl 18.5 of IS 17505-1:2021 & IS:10810 (Part 61)-1988(Flammability Test)	-	5000	-
Cl 18.9 of IS 17505-1:2021(Water immersion test ( effect of water on sheath of cable))	-	5000	-
Cl 18.8 of IS 17505-1:2021& IS:10810 (Part 63)-1993(Smoke density test)	-	5000	-
Cl. 3.5, 18.4 & Annex-E of IS 17505-1:2021(Circuit integrity test under fire)	-	5000	-
Cl. 17.1 Table 9 (iv) e(Heat Shock)	-	5000	-
Cl. 17.1 Table 9 (iv) h(Water absorption (Gravimetric))	-	5000	-
Cl. 17.1 Table 9 (vii) b(Flame test on bunched cable)	-	5000	-
Cl. 17.1 Table 9 (ix)(Abrasion resistance test)	-	5000	-
Cl. 17.1 Table 9 (iv) m(Assessment of Halogen (HCl))	-	5000	-
Cl. 7.3, Table 1 to 5 of IS 8130:2013 & IS:10810 (Part 5)-1984(Conductor Resistance Test)	-	5000	-
Cl. 7.1.2 of IS 8130 : 2013 & IS:10810 (Part 1)-1984(Annealing Test (for copper))	-	5000	-
Cl. 7.1.1 of IS 8130:2013 & IS:10810 (Part 4)-1984(Persulphate Test for tinned copper)	-	5000	-
IS 191:2007 & IS 440(Copper purity test)	-	5000	-
Cl. 11,14,16, Table 4 and Table 6 of IS 17505 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	5000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 36)-1984(Diameter of armour Wire)	-	5000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 37)-1984(Tensile strength and elongation at break)	-	5000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 38)-1984(Torsion Test on galvanised steel wire for armouring)	-	5000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 39)-1984(Winding Test for Formed Wires)	-	5000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 40)-1984(Uniformity of Zinc coating on Round Steel Wires and Formed Steel Wires (Strips))	-	5000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 41)-1984(Mass of Zinc coating on Round Steel Wires and Formed Steel Wires (Strips))	-	5000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 42)-1984(Resistivity test)	-	5000	-
Table 1 and Table 2 of IS 17505 -1: 2021, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	5000	-
Cl 18.2 of IS 17505-1:2021 & IS:10810 (Part 45)-1984(High voltage test)	-	5000	-
Table 1 of IS 17505-1 :2021 & IS:10810 (Part 43)-1984(Insulation Resistance)	-	5000	-
Cl. 18.6 of IS 17505-1:2021 & IS:10810 (Part 58)-1998(Oxygen index)	-	5000	-
Cl. 18.7 of IS 17505-1:2021 & IS:10810 (Part 64)-2003(Temperature Index)	-	5000	-
Table-1 & Table-2 of IS 17505-1:2021 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	5000	-
Specification for thermosetting insulated fire survival cables for fixed installation having low emission of smoke and corrosive gases when affected by fire for working voltages upto and including 1100 V A.C. and 1500 V D.C(Hot deformation)	-	5000	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	5000	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	5000	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	5000	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	5000	-
Table 1 of IS 17505-1: 2021 & IS:10810 (Part 21)-1984(Cold impact test)	-	5000	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 30)-1984(Hot set test)	-	5000	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 13)-1984(Ozone Resistance test)	-	5000	-
Cl 18.5.1 of IS 17505-1 :2021 & IS:10810 (Part 61)-1988(Flame test on single cable)	-	5000	-
Table 1 of IS 17505-1:2021 & IS:10810 (Part 12)-1984(Shrinkage test)	-	5000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	5000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	5000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	5000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	5000	-
Tabel 1 and 2 of IS 17505-1:2021 & IS:10810 (Part 7)-1984(Tensile strength and elongation at break.)	-	5000	-
Tabel 1 and 2 of IS 17505-1:2021 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	5000	-
Cl 18.6 of IS 17505-1: 2021 & IS:10810 (Part 58)-1998(Oxygen Index.)	-	5000	-
Cl 18.8 of IS 17505-1:2021 & IS:10810 (Part 64)-2003(Temperature Index)	-	5000	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 13)-1984(Ozone resistance test)	-	5000	-
Table 2 of IS 17505-1:2021 & IS:10810 (Part 15)-1984(Hot deformation)	-	5000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	5000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	5000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	5000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	5000	-
Table 1 of IS 17505-1:2021 & IS:10810 (Part 12)-1984(Shrinkage test)	-	5000	-
Cl 18.2of IS 17505-1:2021 & IS:10810 (Part 45)-1984.(High Voltage test.)	-	5000	-
Cl 18.5of IS 17505-1:2021 & IS:10810 (Part 53)-1984(Flammability Test)	-	5000	-
Table-2 of IS 17505-1:2021 & IS:10810 (Part 20)-1984(Cold bend test)	-	5000	-
Table-2 of IS 17505-1:2021 & IS:10810 (Part 21)-1984(Cold impact test)	-	5000	-
Cl 18.5 of IS 17505-1:2021 & IS:10810 (Part 61)-1988(Flammability Test)	-	5000	-
Cl 18.9 of IS 17505-1:2021(Water immersion test ( effect of water on sheath of cable))	-	5000	-
Cl 18.8 of IS 17505-1:2021& IS:10810 (Part 63)-1993(Smoke density test)	-	5000	-
Cl. 3.5, 18.4 & Annex-E of IS 17505-1:2021(Circuit integrity test under fire)	-	5000	-
Cl. 17.1 Table 9 (iv) e(Heat Shock)	-	5000	-
Cl. 17.1 Table 9 (iv) h(Water absorption (Gravimetric))	-	5000	-
Cl. 17.1 Table 9 (vii) b(Flame test on bunched cable)	-	5000	-
Cl. 17.1 Table 9 (ix)(Abrasion resistance test)	-	5000	-
Cl. 17.1 Table 9 (iv) m(Assessment of Halogen (HCl))	-	5000	-
Cl. 7.3, Table 1 to 5 of IS 8130:2013 & IS:10810 (Part 5)-1984(Conductor Resistance Test)	-	-	-
Cl. 7.1.2 of IS 8130 : 2013 & IS:10810 (Part 1)-1984(Annealing Test (for copper))	-	-	-
Cl. 7.1.1 of IS 8130:2013 & IS:10810 (Part 4)-1984(Persulphate Test for tinned copper)	-	-	-
IS 191:2007 & IS 440(Copper purity test)	-	-	-
Cl. 11,14,16, Table 4 and Table 6 of IS 17505 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	-	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 36)-1984(Diameter of armour Wire)	-	-	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 37)-1984(Tensile strength and elongation at break)	-	-	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 38)-1984(Torsion Test on galvanised steel wire for armouring)	-	-	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 39)-1984(Winding Test for Formed Wires)	-	-	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 40)-1984(Uniformity of Zinc coating on Round Steel Wires and Formed Steel Wires (Strips))	-	-	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 41)-1984(Mass of Zinc coating on Round Steel Wires and Formed Steel Wires (Strips))	-	-	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 42)-1984(Resistivity test)	-	-	-
Table 1 and Table 2 of IS 17505 -1: 2021, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	-	-
Cl 18.2 of IS 17505-1:2021 & IS:10810 (Part 45)-1984(High voltage test)	-	-	-
Table 1 of IS 17505-1 :2021 & IS:10810 (Part 43)-1984(Insulation Resistance)	-	-	-
Cl. 18.6 of IS 17505-1:2021 & IS:10810 (Part 58)-1998(Oxygen index)	-	-	-
Cl. 18.7 of IS 17505-1:2021 & IS:10810 (Part 64)-2003(Temperature Index)	-	-	-
Table-1 & Table-2 of IS 17505-1:2021 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	-	-
Specification for thermosetting insulated fire survival cables for fixed installation having low emission of smoke and corrosive gases when affected by fire for working voltages upto and including 1100 V A.C. and 1500 V D.C(Hot deformation)	-	-	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	-	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	-	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	-	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	-	-
Table 1 of IS 17505-1: 2021 & IS:10810 (Part 21)-1984(Cold impact test)	-	-	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 30)-1984(Hot set test)	-	-	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 13)-1984(Ozone Resistance test)	-	-	-
Cl 18.5.1 of IS 17505-1 :2021 & IS:10810 (Part 61)-1988(Flame test on single cable)	-	-	-
Table 1 of IS 17505-1:2021 & IS:10810 (Part 12)-1984(Shrinkage test)	-	-	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	-	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	-	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	-	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	-	-
Tabel 1 and 2 of IS 17505-1:2021 & IS:10810 (Part 7)-1984(Tensile strength and elongation at break.)	-	-	-
Tabel 1 and 2 of IS 17505-1:2021 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	-	-
Cl 18.6 of IS 17505-1: 2021 & IS:10810 (Part 58)-1998(Oxygen Index.)	-	-	-
Cl 18.8 of IS 17505-1:2021 & IS:10810 (Part 64)-2003(Temperature Index)	-	-	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 13)-1984(Ozone resistance test)	-	-	-
Table 2 of IS 17505-1:2021 & IS:10810 (Part 15)-1984(Hot deformation)	-	-	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	-	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	-	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	-	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	-	-
Table 1 of IS 17505-1:2021 & IS:10810 (Part 12)-1984(Shrinkage test)	-	-	-
Cl 18.2of IS 17505-1:2021 & IS:10810 (Part 45)-1984.(High Voltage test.)	-	-	-
Cl 18.5of IS 17505-1:2021 & IS:10810 (Part 53)-1984(Flammability Test)	-	-	-
Table-2 of IS 17505-1:2021 & IS:10810 (Part 20)-1984(Cold bend test)	-	-	-
Table-2 of IS 17505-1:2021 & IS:10810 (Part 21)-1984(Cold impact test)	-	-	-
Cl 18.5 of IS 17505-1:2021 & IS:10810 (Part 61)-1988(Flammability Test)	-	-	-
Cl 18.9 of IS 17505-1:2021(Water immersion test ( effect of water on sheath of cable))	-	-	-
Cl 18.8 of IS 17505-1:2021& IS:10810 (Part 63)-1993(Smoke density test)	-	-	-
Cl. 3.5, 18.4 & Annex-E of IS 17505-1:2021(Circuit integrity test under fire)	-	-	-
Cl. 17.1 Table 9 (iv) e(Heat Shock)	-	-	-
Cl. 17.1 Table 9 (iv) h(Water absorption (Gravimetric))	-	-	-
Cl. 17.1 Table 9 (vii) b(Flame test on bunched cable)	-	-	-
Cl. 17.1 Table 9 (ix)(Abrasion resistance test)	-	-	-
Cl. 17.1 Table 9 (iv) m(Assessment of Halogen (HCl))	-	-	-

15 Jun, 2029

-
Included w.e.f.19.06.2025

IS 17048 (2018)

Halogen free flame retardant (HFFR) cables for working voltages up to and including 1 100 Volts - Specification

120000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1 a) (Conductor : Material )	-	3000	-
4.1.1 b) (Material : Seperator tape )	-	1000	-
4.1.1 d) , 11.1, 12.1, 13.1,14.1(Class of conductor )	-	1000	-
4.1.1 e) (Shape of conductor )	-	1000	-
4.1.1 f) (Nominal size of conductor )	-	1000	-
4.2.1, 11.2, 12.2, 13.2, 14.2(Insulation : Material )	-	1000	-
4.2.2, 11.2, 12.2, 13.2, 14.2(Insulation : Application )	-	1000	-
4.2.3,11.2, 12.2, 13.2(Thickness of insulation - Avearge : IS 10810 ( Part 6 ))	-	1000	-
4.2.3, 11.2, 12.2, 13.2, 14.2(Thickness of insulation - miniumum : IS 10810 ( Part 6 ))	-	1000	-
4.2.4(Insulation : Tensile stregth ( Before ageing)-IS 10810 (Part 7) )	-	1000	-
4.2.4(Insulation : Elongation ( Before ageing) -IS 10810 (Part 7))	-	1000	-
4.2.4(Insulation : Tensile stregth ( After ageing) - IS 10810 (Part 7) )	-	3000	-
4.2.5(Insulation : Tensile stregth variation ( After ageing) - IS 10810 (Part 7) )	-	3000	-
4.2.4(Insulation : Elongation (after ageing) - IS 10810 (Part 7) )	-	3000	-
4.2.5(Insulation : Elongation variation (after ageing) - IS 10810 (Part 7) )	-	3000	-
4.3(Fillers)	-	1000	-
4.4(Binder Tape)	-	1000	-
4.5.1,13.4, 14.4(Sheath : Compound )	-	1000	-
4.5.2, 13.4, 14.4(Sheath : Application)	-	1000	-
4.5.3,13.4, 14.4(Thickness of sheath - Average : IS 10810 (Part 6))	-	1000	-
4.5.3,13.4, 14.4(Thickness of sheath - Minimum : IS 10810 (Part 6))	-	1000	-
4.5.4, 13.4(Sheath : Tensile stregth ( Before ageing)-IS 10810 (Part 7) )	-	1000	-
4.5.4,13.4(Sheath : Elongation ( Before ageing) -IS 10810 (Part 7))	-	1000	-
4.5.4, 13.4, 14.4(Sheath : Tensile stregth ( After ageing) - IS 10810 (Part 7) )	-	3000	-
4.5.5, 13.4, 14.4(Sheath : Tensile stregth variation ( After ageing) - IS 10810 (Part 7) )	-	3000	-
4.5.4, 13.4, 14.4(Sheath : Elongation (after ageing) - IS 10810 (Part 7) )	-	3000	-
4.5.5, 13.4,14.4(Sheath : Elongation variation (after ageing) - IS 10810 (Part 7) )	-	3000	-
4.5.5, 11.3, 12.3, 13.6, 14.6(Overall Dimensions)	-	1000	-
4.5.5.1, 11.3, 12.3,13.5, 14.5(Ovality)	-	1000	-
4.5.6, 13.4(Colour of Sheath)	-	1000	-
5.1(High Voltage Test (at Room Temperature))	-	1000	-
5.2(Spark Test (Routine Test))	-	1000	-
5.3(Flammability Test- IS 10810 (Part 53).)	-	1000	-
5.4(Oxygen Index Test- IS 10810 (Part 58))	-	5000	-
5.5(Temperature Index-IS 10810 (Part 64).)	-	3000	-
5.6(Smoke Density-IS 10810 (Part 63).)	-	5000	-
5.7(Assessment of Halogen- Table 1 of Annex D)	-	3000	-
5.1(Persulphate Test- IS 10810 (Part 4).)	-	1000	-
5.11(Flame Retardant Test- IS 10810 (Part 61),)	-	1000	-
5.12(Hot Set Test- IS 10810 (Part 30).)	-	1000	-
5.12(Permanent Set - IS 10810 (Part 30).)	-	1000	-
5.13(Water Immersion Test (Effect of Water on Sheath) : Tensile strength -IS 10810 (Part 7).)	-	5000	-
5.13(Water Immersion Test (Effect of Water on Sheath) : Elogation -IS 10810 (Part 7).)	-	3000	-
5.14(Ozone Resistance Test -IS 10810 (Part 13 ))	-	12000	-
5.15(Cold Bend Test-IS 10810 (Part 20).)	-	1000	-
5.16(Cold Impact Test- IS 10810 (Part 21).)	-	1000	-
6.1, Table 1(CORE IDENTIFICATION)	-	1000	-
6.2(Core Identification by Numbers)	-	1000	-
6.2.1(Preferred Arrangement of Marking)	-	1000	-
6.2.2(Durability)	-	1000	-
7.0(CABLE CODE)	-	1000	-
9.0( IDENTIFICATION)	-	1000	-
10.1(Packing )	-	1000	-
10.2(marking)	-	1000	-
10.2.1(Standards marking)	-	1000	-
13.3, 14.3(assembly of cores )	-	1000	-
6.1(General Requirements)	-	1000	-
6.1.1(Colour Combination Green Yellow)	-	1000	-
12.1(Conductor)	-	1000	-
12.2, Table 4(insulation)	-	1000	-
Table 4(Copper Purity test)	-	5000	-
4.3.1 (e)(Fluorine content test (Fillers))	-	3000	-
4.3.1 (d)(Presence of fluorine test (Fillers))	-	10000	-
4.3.1 (c)(Conductivity test (Fillers))	-	3000	-
4.3.1 (b)(pH test (Fillers))	-	10000	-
4.3.1 (a)(HCl test (Fillers))	-	3000	-
5.7 (a)(HCl test (Assessment of halogen test))	-	3000	-
5.7 (b)(pH test (Assessment of halogen test))	-	2000	-
5.7 (c)(Conductivity test (Assessment of halogen test))	-	10000	-
5.7 (d)(Presence of fluorine test (Assessment of halogen test))	-	3000	-
5.7 (e)(Fluorine content test (Assessment of halogen test))	-	5000	-
Table 2 ,( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )(Insulation Resistance)	-	3000	-
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Conductor Resistance)	-	3000	-
Table 2 , Clause .5.13(Water immersion test (Effect of water on sheath) - TS Variation of Sheath)	-	3000	-
Table 2 , Clause 5.13(Water immersion test (Effect of water on sheath) - Elongation Variation of Sheath)	-	3000	-
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Hot Deformation)	-	3000	-
Table 2, III.a.ii(Annealing test (for Cu, before stranding))	-	1000	-
Table 2, II.a, b(Wrapping test before stranding (for Al))	-	1000	-
Cl.4.2.1 & Annex A(Insulation Resistance Constant at Rated Temperature (70°C))	-	3000	-
Table 2, III a (i)(Conductor Resistance)	-	3000	-
Annex A(Hot Deformation)	-	3000	-
6.1, Table 1(CORE IDENTIFICATION)	-	1000	-
6.1(General Requirements)	-	1000	-
6.1.1(Colour Combination Green Yellow)	-	1000	-
12.1(Conductor)	-	1000	-
12.2, Table 4(insulation)	-	1000	-
Table 4(Copper Purity test)	-	5000	-
4.3.1 (e)(Fluorine content test (Fillers))	-	10000	-
4.3.1 (d)(Presence of fluorine test (Fillers))	-	10000	-
4.3.1 (c)(Conductivity test (Fillers))	-	10000	-
4.3.1 (b)(pH test (Fillers))	-	3000	-
4.3.1 (a)(HCl test (Fillers))	-	10000	-
5.7 (a)(HCl test (Assessment of halogen test))	-	3000	-
5.7 (b)(pH test (Assessment of halogen test))	-	3000	-
5.7 (c)(Conductivity test (Assessment of halogen test))	-	3000	-
5.7 (d)(Presence of fluorine test (Assessment of halogen test))	-	10000	-
5.7 (e)(Fluorine content test (Assessment of halogen test))	-	3000	-
Table 2 ,( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )(Insulation Resistance)	-	3000	-
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Conductor Resistance)	-	3000	-
Table 2 , Clause .5.13(Water immersion test (Effect of water on sheath) - TS Variation of Sheath)	-	5000	-
Table 2 , Clause 5.13(Water immersion test (Effect of water on sheath) - Elongation Variation of Sheath)	-	5000	-
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Hot Deformation)	-	3000	-
Table 2, III.a.ii(Annealing test (for Cu, before stranding))	-	1000	-
Table 2, II.a, b(Wrapping test before stranding (for Al))	-	1000	-
Cl.4.2.1 & Annex A(Insulation Resistance Constant at Rated Temperature (70°C))	-	3000	-
Table 2, III a (i)(Conductor Resistance)	-	3000	-
Annex A(Hot Deformation)	-	3000	-
6.1, Table 1(CORE IDENTIFICATION)	-	1000	-
6.1(General Requirements)	-	1000	-
6.1.1(Colour Combination Green Yellow)	-	1000	-
12.1(Conductor)	-	1000	-
12.2, Table 4(insulation)	-	2000	-
Table 4(Copper Purity test)	-	5000	-
4.3.1 (e)(Fluorine content test (Fillers))	-	10000	-
4.3.1 (d)(Presence of fluorine test (Fillers))	-	3000	-
4.3.1 (c)(Conductivity test (Fillers))	-	3000	-
4.3.1 (b)(pH test (Fillers))	-	3000	-
4.3.1 (a)(HCl test (Fillers))	-	3000	-
5.7 (a)(HCl test (Assessment of halogen test))	-	3000	-
5.7 (b)(pH test (Assessment of halogen test))	-	5000	-
5.7 (c)(Conductivity test (Assessment of halogen test))	-	5000	-
5.7 (d)(Presence of fluorine test (Assessment of halogen test))	-	5000	-
5.7 (e)(Fluorine content test (Assessment of halogen test))	-	5000	-
Table 2 ,( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )(Insulation Resistance)	-	5000	-
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Conductor Resistance)	-	5000	-
Table 2 , Clause .5.13(Water immersion test (Effect of water on sheath) - TS Variation of Sheath)	-	5000	-
Table 2 , Clause 5.13(Water immersion test (Effect of water on sheath) - Elongation Variation of Sheath)	-	5000	-
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Hot Deformation)	-	5000	-
Table 2, III.a.ii(Annealing test (for Cu, before stranding))	-	5000	-
Table 2, II.a, b(Wrapping test before stranding (for Al))	-	1000	-
Cl.4.2.1 & Annex A(Insulation Resistance Constant at Rated Temperature (70°C))	-	1000	-
Table 2, III a (i)(Conductor Resistance)	-	2000	-
Annex A(Hot Deformation)	-	2000	-
6.1, Table 1(CORE IDENTIFICATION)	-	1000	-
6.1(General Requirements)	-	1000	-
6.1.1(Colour Combination Green Yellow)	-	1000	-
12.1(Conductor)	-	1000	-
12.2, Table 4(insulation)	-	1000	-
Table 4(Copper Purity test)	-	10000	-
4.3.1 (e)(Fluorine content test (Fillers))	-	10000	-
4.3.1 (d)(Presence of fluorine test (Fillers))	-	5000	-
4.3.1 (c)(Conductivity test (Fillers))	-	5000	-
4.3.1 (b)(pH test (Fillers))	-	5000	-
4.3.1 (a)(HCl test (Fillers))	-	5000	-
5.7 (a)(HCl test (Assessment of halogen test))	-	5000	-
5.7 (b)(pH test (Assessment of halogen test))	-	5000	-
5.7 (c)(Conductivity test (Assessment of halogen test))	-	5000	-
5.7 (d)(Presence of fluorine test (Assessment of halogen test))	-	5000	-
5.7 (e)(Fluorine content test (Assessment of halogen test))	-	5000	-
Table 2 ,( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )(Insulation Resistance)	-	2000	-
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Conductor Resistance)	-	2000	-
Table 2 , Clause .5.13(Water immersion test (Effect of water on sheath) - TS Variation of Sheath)	-	5000	-
Table 2 , Clause 5.13(Water immersion test (Effect of water on sheath) - Elongation Variation of Sheath)	-	5000	-
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Hot Deformation)	-	2000	-
Table 2, III.a.ii(Annealing test (for Cu, before stranding))	-	2000	-
Table 2, II.a, b(Wrapping test before stranding (for Al))	-	2000	-
Cl.4.2.1 & Annex A(Insulation Resistance Constant at Rated Temperature (70°C))	-	5000	-
Table 2, III a (i)(Conductor Resistance)	-	5000	-
Annex A(Hot Deformation)	-	2000	-
6.1, Table 1(CORE IDENTIFICATION)	-	2000	-
6.1(General Requirements)	-	1000	-
6.1.1(Colour Combination Green Yellow)	-	2000	-
12.1(Conductor)	-	2000	-
12.2, Table 4(insulation)	-	2000	-
Table 4(Copper Purity test)	-	4000	-
4.3.1 (e)(Fluorine content test (Fillers))	-	2000	-
4.3.1 (d)(Presence of fluorine test (Fillers))	-	2000	-
4.3.1 (c)(Conductivity test (Fillers))	-	2000	-
4.3.1 (b)(pH test (Fillers))	-	2000	-
4.3.1 (a)(HCl test (Fillers))	-	2000	-
5.7 (a)(HCl test (Assessment of halogen test))	-	5000	-
5.7 (b)(pH test (Assessment of halogen test))	-	2000	-
5.7 (c)(Conductivity test (Assessment of halogen test))	-	3000	-
5.7 (d)(Presence of fluorine test (Assessment of halogen test))	-	3000	-
5.7 (e)(Fluorine content test (Assessment of halogen test))	-	3000	-
Table 2 ,( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )(Insulation Resistance)	-	3000	-
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Conductor Resistance)	-	3000	-
Table 2 , Clause .5.13(Water immersion test (Effect of water on sheath) - TS Variation of Sheath)	-	3000	-
Table 2 , Clause 5.13(Water immersion test (Effect of water on sheath) - Elongation Variation of Sheath)	-	5000	-
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Hot Deformation)	-	2000	-
Table 2, III.a.ii(Annealing test (for Cu, before stranding))	-	2000	-
Table 2, II.a, b(Wrapping test before stranding (for Al))	-	5000	-
Cl.4.2.1 & Annex A(Insulation Resistance Constant at Rated Temperature (70°C))	-	5000	-
Table 2, III a (i)(Conductor Resistance)	-	5000	-
Annex A(Hot Deformation)	-	5000	-
6.1, Table 1(CORE IDENTIFICATION)	-	3000	-
6.1(General Requirements)	-	3000	-
6.1.1(Colour Combination Green Yellow)	-	2000	-
12.1(Conductor)	-	2000	-
12.2, Table 4(insulation)	-	2000	-
Table 4(Copper Purity test)	-	2000	-
4.3.1 (e)(Fluorine content test (Fillers))	-	2000	-
4.3.1 (d)(Presence of fluorine test (Fillers))	-	2000	-
4.3.1 (c)(Conductivity test (Fillers))	-	2000	-
4.3.1 (b)(pH test (Fillers))	-	2000	-
4.3.1 (a)(HCl test (Fillers))	-	2000	-
5.7 (a)(HCl test (Assessment of halogen test))	-	2000	-
5.7 (b)(pH test (Assessment of halogen test))	-	2000	-
5.7 (c)(Conductivity test (Assessment of halogen test))	-	2000	-
5.7 (d)(Presence of fluorine test (Assessment of halogen test))	-	2000	-
5.7 (e)(Fluorine content test (Assessment of halogen test))	-	2000	-
Table 2 ,( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )(Insulation Resistance)	-	2000	-
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Conductor Resistance)	-	2000	-
Table 2 , Clause .5.13(Water immersion test (Effect of water on sheath) - TS Variation of Sheath)	-	2000	-
Table 2 , Clause 5.13(Water immersion test (Effect of water on sheath) - Elongation Variation of Sheath)	-	2000	-
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Hot Deformation)	-	2000	-
Table 2, III.a.ii(Annealing test (for Cu, before stranding))	-	2000	-
Table 2, II.a, b(Wrapping test before stranding (for Al))	-	2000	-
Cl.4.2.1 & Annex A(Insulation Resistance Constant at Rated Temperature (70°C))	-	2000	-
Table 2, III a (i)(Conductor Resistance)	-	2000	-
Annex A(Hot Deformation)	-	2000	-
6.1, Table 1(CORE IDENTIFICATION)	-	1000	-
6.1(General Requirements)	-	1000	-
6.1.1(Colour Combination Green Yellow)	-	1000	-
12.1(Conductor)	-	1000	-
12.2, Table 4(insulation)	-	1000	-
Table 4(Copper Purity test)	-	1000	-
4.3.1 (e)(Fluorine content test (Fillers))	-	1000	-
4.3.1 (d)(Presence of fluorine test (Fillers))	-	1000	-
4.3.1 (c)(Conductivity test (Fillers))	-	1000	-
4.3.1 (b)(pH test (Fillers))	-	1000	-
4.3.1 (a)(HCl test (Fillers))	-	1000	-
5.7 (a)(HCl test (Assessment of halogen test))	-	1000	-
5.7 (b)(pH test (Assessment of halogen test))	-	1000	-
5.7 (c)(Conductivity test (Assessment of halogen test))	-	1000	-
5.7 (d)(Presence of fluorine test (Assessment of halogen test))	-	1000	-
5.7 (e)(Fluorine content test (Assessment of halogen test))	-	1000	-
Table 2 ,( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )(Insulation Resistance)	-	1000	-
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Conductor Resistance)	-	1000	-
Table 2 , Clause .5.13(Water immersion test (Effect of water on sheath) - TS Variation of Sheath)	-	1000	-
Table 2 , Clause 5.13(Water immersion test (Effect of water on sheath) - Elongation Variation of Sheath)	-	1000	-
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Hot Deformation)	-	1000	-
Table 2, III.a.ii(Annealing test (for Cu, before stranding))	-	1000	-
Table 2, II.a, b(Wrapping test before stranding (for Al))	-	1000	-
Cl.4.2.1 & Annex A(Insulation Resistance Constant at Rated Temperature (70°C))	-	1000	-
Table 2, III a (i)(Conductor Resistance)	-	1000	-
Annex A(Hot Deformation)	-	1000	-

15 Jun, 2029

-
included w.e.f 09-12-2025

IS 2465 (1984)

Specification for cables for motor vehicles (Second Revision)

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1(Insulation)	-	500	-
7.3(Insulation)	-	500	-
8(Core Identification)	-	500	-
9(Laying up of cores)	-	500	-
10.1.1(Sheathing )	-	500	-
10.2(Sheathing )	-	500	-
3 & 6(Flexibility class)	-	500	-
3 & 6(Construction)	-	500	-
3 & 6(Diameter of wire(mm))	-	1000	-
3 & 6(Annealing test)	-	1000	-
3 & 6(Persulphate Test)	-	1000	-
3 & 6(Conductor resistance Test (ohm/km at 20˚c))	-	1000	-
7.2, 10.3, 11(Dimensions & thickness )	-	1000	-
7.2, 10.3, 11(Dimensions & thickness )	-	1000	-
7.2, 10.3, 11(Overall Dimension (mm))	-	1000	-
4.2 & 12.1(Without Ageing For Insulation Tensile Strength (N/mm²))	-	2000	-
4.2 & 12.1, (f), 1(elongation at break (N/mm²))	-	2000	-
4.2 & 12.1, (f), 1(Tensile Strength at break (N/mm²))	-	2000	-
4.2 & 12.1, (e), 1(elongation test at break)	-	2000	-
4.2 & 12.1, (e), 1(Tensile strength at break)	-	2000	-
4.2 & 12.1, (f), 2(Ageing in air oven)	-	2000	-
4.2 & 12.1, (f), 3(Ageing in oxygen bomb)	-	2000	-
4.2 & 12.1, (e), 2(After Ageing in air oven)	-	2000	-
4.2 & 12.1, (e), 3(Loss of mass test (mg/cm²) of Insulation)	-	2000	-
4.2 & 12.1, (e), 3(Loss of mass test (mg/cm²) of Sheath)	-	2000	-
4.2 & 12.1, (e), 4(Hot deformation test (%) of Insulation)	-	1000	-
4.2 & 12.1, (e), 4(Hot deformation test (%) of Sheath)	-	1000	-
4.2 & 12.1, (e), 5(Heat Shock Test of Insulation)	-	1000	-
4.2 & 12.1, (e), 5(Heat Shock Test of Sheath)	-	1000	-
4.2 & 12.1, (e), 6(Shrinkage Test (%) of Insulation)	-	1000	-
4.2 & 12.1, (e), 6(Shrinkage Test (%) of Sheath)	-	1000	-
14(High Voltage Test)	-	1000	-
15(SPARK TEST FOR SINGLE CORE GENERAL WIRING CABLES)	-	1000	-
16.1(CAPACITANCE TEST FOR PVC INSULATION IGNITION CABLE)	-	1000	-
17.1(OZONE RESISTANCE TEST FOR IGNITION CABLES)	-	2000	-
18.1(EFFECT OF HEAT ON FLEXIBILITY FOR IGNITION CABLES)	-	2000	-
19.1(EFFECT OF OIL ON IGNITION CABLES)	-	2000	-
19.2(EFFECT OF OIL ON IGNITION CABLES)	-	2000	-
20.3(EFFECT OF LUBRICATING OIL)	-	2000	-
20.3(EFFECT OF LUBRICATING OIL)	-	2000	-
20.3(EFFECT OF BRAKE FLUID)	-	2000	-
20.3(EFFECT OF BRAKE FLUID)	-	2000	-
20.3(EFFECT OF DIESEL)	-	2000	-
20.3(EFFECT OF DIESEL)	-	2000	-
20.3(Increase in average diameter %)	-	1000	-
20.3(Wrapping test)	-	1000	-
21.1(EFFECT OF COOLING ON FLEXIBILITY)	-	2000	-
21.2(EFFECT OF COOLING ON FLEXIBILITY)	-	2000	-
21.2(EFFECT OF COOLING ON FLEXIBILITY)	-	2000	-
22.1(FLAMMABILITY TEST)	-	1000	-
22.1(FLAMMABILITY TEST)	-	1000	-
23.1(Manufacturer's Identification)	-	500	-
23.1(Manufacturer's Identification)	-	500	-
24.1(PACKING AND MARKING)	-	500	-
24.2(PACKING AND MARKING)	-	500	-
24.2.1(PACKING AND MARKING)	-	500	-
12.1.b(Persulphate test (when applicable))	-	1000	-
6.1, 12.3, 12.1.c(Conductor Resistance)	-	1000	-
12.1.e4(Hot deformation)	-	1000	-
12.1.e5(Heat Shock)	-	1000	-
CL.12.1 (e) 2(Tensile Strength After Ageing)	-	2000	-
CL.12.1 (e) 2(Elongation After Ageing)	-	2000	-
CL.12.1 (e) 2(Tensile Strength Variation)	-	2000	-
CL.12.1 (e) 2(Elongation Variation)	-	2000	-
CL.12.1 (e) 2(Elongation Variation)	-	2000	-
Cl.12 (e) 5(Heat shock test)	-	1000	-
Cl.12 (e) 4(Hot Deformation Test)	-	1000	-
Cl.12 (e) 6(Shrinkage Test)	-	1000	-
Cl.12 (e) 6(Shrinkage Test (Cracks Observed))	-	1000	-
Cl. 12.1 (e) 3(Loss of Mass Insulation)	-	2000	-

15 Jun, 2029

-
Included w.e.f 14.08.2025

IS 9968 : Part 1 (1988)

Specification for elastomer insulatedcables: Part 1 for working voltages up to and including 1100 volts (First Revision)

10500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1( Copper Cooduetor)	-	500	-
3.2(Aluminium conductor)	-	500	-
4.1(INSULATION : lnsulation for General Service)	-	500	-
4.2(INSULATION : Heat Resisting insulation)	-	500	-
4.3(INSULATION : Silicone Rubber Insulation)	-	500	-
5.1(TAPE : Proofed Tape)	-	500	-
5.2(TAPE : 2 Polyethyl_ Terephthalate ( PETP ) Tape or Plastic: Tape or Any Other SlIIitable Tape )	-	500	-
5.3(TAPE : Giass Tape)	-	500	-
6.1(FILLERS : )	-	500	-
7.1(BRAID : Textile Braid)	-	500	-
7.2(BRAID : Glass Braid )	-	500	-
8.1(SHEATH : General Service Insulated Cables and Flexible Cords)	-	500	-
8.2(SHEATH :Heat Resisting Insulated Cables)	-	500	-
9.1(PresenRtive Compound)	-	500	-
9.2(Varnish)	-	500	-
10( Conductor )	-	500	-
11(Separator tape)	-	500	-
12.2(Insulation : Thickness of Insufatien)	-	1000	-
12.4(Insulation : Allplication of Insulation)	-	1000	-
13(CORE IDENTiFICATlON)	-	500	-
14(Tape)	-	500	-
15(BRAIDING)	-	500	-
16(COMPOUNDING AND VARNISHING)	-	500	-
17(LAYING UP OF CORES)	-	500	-
18( Binder tape)	-	500	-
19.2(Sheath : Thickness of Sheath)	-	1000	-
19.4( Sheath :Colour)	-	500	-
20( Overall diameter)	-	1000	-
21. (a)(Persulphate tests (for copper))	-	2000	-
21. (b)(Annealing Test (for coper))	-	1000	-
21. (c)( Tensile Test (for aluminium))	-	1000	-
21. (d)( Wrapping Test (for aluminium))	-	1000	-
21. (e)(Conductor Resistance )	-	1000	-
21.1( Tensile strength )	-	1000	-
22.1( Elongation)	-	1000	-
21.1(type test : Ageing In air oven)	-	2000	-
21.1(type test : Ageing in air bomb)	-	2000	-
21.1(type test : Ageing In oxygen bomb)	-	2000	-
21.1(type test : Hot set elongation)	-	1000	-
21.1(type test : Tear resistance )	-	1000	-
22.2(type test :Insulauon resistance High voltage (water immersron ) test)	-	1000	-
22.2(type test : Flammability test ( applicable to cables finished With SE 3 and SE 4 sheaths only) )	-	1000	-
21(Water absorption test)	-	2000	-
23(identification)	-	500	-
Cl No. 4.1(Ageing in oxygen bomb - Elongation)	-	2000	-
Cl No. 4.1(Ageing in oxygen bomb - Tensile strength )	-	2000	-
Cl No. 4.1(Ageing in air bomb - Elongation)	-	2000	-
Cl No. 4.1(Ageing in air bomb - Tensile strength )	-	2000	-
Cl No. 4.1(Ageing in air oven - Elongation)	-	2000	-
Cl No. 4.1(Ageing in air oven - Tensile strength )	-	2000	-
Cl No. 22.2(High Voltage Test (Water Immersion))	-	1000	-
Cl No. 4.1(Insulation resistance)	-	1000	-
Cl No. 22.4, Appendix B (Flexing test for cords for use with electric iron )	-	2000	-
Cl No. 22.2.2/22.2.3(High Voltage Test / Spark test)	-	1000	-
Cl No. 23.1, 23.2(Identification)	-	500	-
21.1((f) Oil resistance)	-	2000	-
Cl.9.1(Compound and Varnish)	-	500	-
Cl.9.2(Compound and Varnish)	-	500	-
Cl.21.1 & Table 2 of IS: 6380-1984(Water Absorption Test)	-	3000	-
Cl.19.1(Application of Sheath)	-	500	-
Cl.21.1 & Table 3 of IS: 6380-1984(Physical Test on outer sheath (Without Ageing))	-	1000	-
Cl.21.1 & Table 3 of IS: 6380-1984(Physical Test on outer sheath (Without Ageing))	-	1000	-
Cl.21.1 & Table 3 of IS: 6380-1984(Physical Test on outer sheath (Without Ageing))	-	1000	-
Cl.21.1 & Table 3 of IS: 6380-1984(Physical Test on outer sheath (After ageing in air oven))	-	1000	-
Cl.21.1 & Table 3 of IS: 6380-1984(Physical Test on outer sheath (After ageing in air oven))	-	1000	-
Cl.21.1 & Table 3 of IS: 6380-1984(Physical Test on outer sheath (After ageing in air Bomb ))	-	1000	-
Cl.21.1 & Table 3 of IS: 6380-1984(Physical Test on outer sheath (After ageing in air Bomb ))	-	1000	-
Cl.21.1 & Table 3 of IS: 6380-1984(Physical Test on outer sheath (Oil Resistance Test ))	-	1000	-
Cl.21.1 & Table 3 of IS: 6380-1984(Physical Test on outer sheath (Oil Resistance Test ) Variation on Elongation (Percentage))	-	1000	-
Cl.21.1 & Table 3 of IS: 6380-1984(Physical Test on outer sheath (Hot Set Test))	-	1000	-
Cl.21.1 & Table 3 of IS: 6380-1984(Physical Test on outer sheath (Hot Set Test))	-	1000	-
Cl.21.1 & Table 2 of IS: 6380-1984(Insulation Resistance Test)	-	1000	-
Cl.21.1 & Table 2 of IS: 6380-1984(Insulation Resistance Test)	-	1000	-

15 Jun, 2029

-
Included w.e.f 14.08.2025

IS 4250 (2025)

Electric Food-Mixers (Liquidizers and Grinders) and Centrifugal Juicers ï¿½ Specification ( Second Revision )

35000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(General Requirements)	-	1000	-
Cl-5(General Conditions for the tests)	-	1000	-
Cl-6(Classification)	-	1000	-
Cl-7(Marking)	-	1000	-
Cl-8(Safety Requirements)	-	7000	-
Cl-9(Endurance fpr motor and base assembly)	-	1000	-
Cl-10.2("Grinding Coffee (for Machines that Have a Dry Grinding Arrangement)")	-	1000	-
Cl-10.3(Whisking Egg Whites (for Machines that have Whisking Egg Arrangement))	-	1000	-
Cl-10.4(Idli Batter)	-	1000	-
Cl-10.5(Operational Tests for Juicers)	-	2000	-
Cl-11(Temperature Withstand Test for Bowl)	-	1000	-
Cl-12.1(Test for Switches)	-	2000	-
Cl-13(Strength of Assembly)	-	3000	-
Cl-14.2, 14.3 Table-2 (i)(Protection against access to live parts)	-	2000	-
Cl-14.2, Table-2 (ii)(Power input and current)	-	3000	-
Cl-14.2, 14.3 Table-2 (iii)(Leakage current and electric strength at operating temperature)	-	2000	-
Cl-14.2, Table-2 (iv)(Moisture resistance)	-	2000	-
Cl-14.2, Table-2 (v)(Leakage current and electric strength)	-	2000	-
Cl-14.2, 14.3 Table-2 (vi)(Provision for earthing)	-	1000	-

15 Jun, 2029

-
Included w.e.f 14.08.2025 Exclusion: Cl-19.11.4.1-Cl-19.11.4.7 (EMI/EMC)

IS 9857 (1990)

Welding cables - Specification (First Revision)

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Conductor : Material )	-	500	-
5(SEPARATOR)	-	500	-
6(COVERING)	-	500	-
7(CONDUCTOR : CONSTRUCTION )	-	500	-
8(S E P A R A T O R)	-	500	-
9.1(C O V E R I N G : Application )	-	500	-
9.2(T h i c k n e s s o f C o v e r i n g)	-	1000	-
9.3(T o l e r a n c e on Thickness o f C o v e r i n g)	-	1000	-
9.4(A p p l i c a t i o n of C o v e r i n g)	-	500	-
9.5(Colour of C o v e r i n g)	-	500	-
10.1 a) 1)(Annealing test - IS 10810: Part 1)	-	1000	-
10.1 a) 2)(Conductor resistance tes - IS 10810 : Part 5)	-	1000	-
10.1 c) 1)(Physical tests for covering : Tensile strength )	-	1000	-
10.1 c) 1)(Physical tests for covering : Elongation at break )	-	1000	-
10.1 c) 2)(Physical tests for covering - Ageing in Air oven : Tensile strength variation)	-	2000	-
10.1 c) 2)(Physical tests for covering - Ageing in Air oven : Tensile strength )	-	2000	-
10.1 c) 2)(Physical tests for covering -Ageing in Air oven : Elongation variation at break )	-	2000	-
10.1 c) 3)(Physical tests for covering - Ageing in Air Bomb : Tensile strength variation )	-	2000	-
10.1 c) 3)(Physical tests for covering -Ageing in Air Bomb : Elongation variation at break )	-	2000	-
10.1 c) 4)(Physical tests for covering - Oil Resistance : Tensile strength variation )	-	2000	-
10.1 c) 4)(Physical tests for covering - Oil Resistance : Elongation variation at break )	-	2000	-
10.1 c) 5)(Hot set test )	-	1000	-
10.1 c) 5)(Permanent set )	-	1000	-
11.1(High Voltage Test ( Water Immersion Test ))	-	1000	-
11.2(Spark Test)	-	1000	-
11.3(Static Flexibility Test)	-	1000	-
11.4(Flammability Test)	-	1000	-
12.1(Manufacturer's Identification)	-	5000	-
12.2(Cable Identification)	-	500	-
12.3(Cable Code)	-	500	-
13.1(Packing )	-	500	-
13.2(Marking)	-	500	-
14(CABLE RATINGS)	-	500	-
15(VOLTAGE DROP)	-	500	-
Table 4(Copper purity test)	-	500	-
Table 2(Oil resistance - Elongation)	-	2000	-
Table 2(Oil resistance - Tensile strength )	-	2000	-
Table 2(Ageing in air bomb - Elongation)	-	2000	-
Table 2(Ageing in air bomb - Tensile strength )	-	2000	-
Table 1 (Thickness of covering)	-	1000	-
15.1 (d)(Heat Shock Test)	-	1000	-
15.1 (d)(Hot Deformation Test)	-	1000	-
15.1 (d)(Loss Of Mass Test)	-	1000	-
10.1(b), Table 1(Thickness of covering)	-	1000	-
10.1 c) 2)(Physical tests for covering -Ageing in Air oven : Elongation at break )	-	2000	-
4(Conductor : Material )	-	500	-
5(SEPARATOR)	-	500	-
6(COVERING)	-	500	-
7(CONDUCTOR : CONSTRUCTION )	-	500	-
8(S E P A R A T O R)	-	500	-
9.1(C O V E R I N G : Application )	-	500	-
9.2(T h i c k n e s s o f C o v e r i n g)	-	1000	-
9.3(T o l e r a n c e on Thickness o f C o v e r i n g)	-	1000	-
9.4(A p p l i c a t i o n of C o v e r i n g)	-	500	-
9.5(Colour of C o v e r i n g)	-	500	-
10.1 a) 1)(Annealing test - IS 10810: Part 1)	-	1000	-
10.1 a) 2)(Conductor resistance tes - IS 10810 : Part 5)	-	1000	-
10.1 c) 1)(Physical tests for covering : Tensile strength )	-	1000	-
10.1 c) 1)(Physical tests for covering : Elongation at break )	-	1000	-
10.1 c) 2)(Physical tests for covering - Ageing in Air oven : Tensile strength variation)	-	2000	-
10.1 c) 2)(Physical tests for covering -Ageing in Air oven : Elongation at break )	-	2000	-
10.1 c) 2)(Physical tests for covering - Ageing in Air oven : Tensile strength )	-	2000	-
10.1 c) 2)(Physical tests for covering -Ageing in Air oven : Elongation variation at break )	-	2000	-
10.1 c) 3)(Physical tests for covering - Ageing in Air Bomb : Tensile strength variation )	-	2000	-
10.1 c) 3)(Physical tests for covering -Ageing in Air Bomb : Elongation variation at break )	-	2000	-
10.1 c) 4)(Physical tests for covering - Oil Resistance : Tensile strength variation )	-	2000	-
10.1 c) 4)(Physical tests for covering - Oil Resistance : Elongation variation at break )	-	2000	-
10.1 c) 5)(Hot set test )	-	1000	-
10.1 c) 5)(Permanent set )	-	1000	-
11.1(High Voltage Test ( Water Immersion Test ))	-	2000	-
11.2(Spark Test)	-	1000	-
11.3(Static Flexibility Test)	-	1000	-
11.4(Flammability Test)	-	1000	-
12.1(Manufacturer's Identification)	-	500	-
12.2(Cable Identification)	-	500	-
12.3(Cable Code)	-	500	-
13.1(Packing )	-	500	-
13.2(Marking)	-	500	-
14(CABLE RATINGS)	-	500	-
15(VOLTAGE DROP)	-	500	-
Table 4(Copper purity test)	-	500	-
Table 2(Oil resistance - Elongation)	-	2000	-
Table 2(Oil resistance - Tensile strength )	-	2000	-
Table 2(Ageing in air bomb - Elongation)	-	2000	-
Table 2(Ageing in air bomb - Tensile strength )	-	2000	-
Table 1 (Thickness of covering)	-	1000	-
15.1 (d)(Heat Shock Test)	-	1000	-
15.1 (d)(Hot Deformation Test)	-	1000	-
15.1 (d)(Loss Of Mass Test)	-	2000	-
10.1(b), Table 1(Thickness of covering)	-	1000	-
4(Conductor : Material )	-	500	-
5(SEPARATOR)	-	500	-
6(COVERING)	-	500	-
7(CONDUCTOR : CONSTRUCTION )	-	500	-
8(S E P A R A T O R)	-	500	-
9.1(C O V E R I N G : Application )	-	500	-
9.2(T h i c k n e s s o f C o v e r i n g)	-	1000	-
9.3(T o l e r a n c e on Thickness o f C o v e r i n g)	-	1000	-
9.4(A p p l i c a t i o n of C o v e r i n g)	-	500	-
9.5(Colour of C o v e r i n g)	-	500	-
10.1 a) 1)(Annealing test - IS 10810: Part 1)	-	1000	-
10.1 a) 2)(Conductor resistance tes - IS 10810 : Part 5)	-	2000	-
10.1 c) 1)(Physical tests for covering : Tensile strength )	-	2000	-
10.1 c) 1)(Physical tests for covering : Elongation at break )	-	2000	-
10.1 c) 2)(Physical tests for covering - Ageing in Air oven : Tensile strength variation)	-	2000	-
10.1 c) 2)(Physical tests for covering -Ageing in Air oven : Elongation at break )	-	2000	-
10.1 c) 2)(Physical tests for covering - Ageing in Air oven : Tensile strength )	-	2000	-
10.1 c) 2)(Physical tests for covering -Ageing in Air oven : Elongation variation at break )	-	2000	-
10.1 c) 3)(Physical tests for covering - Ageing in Air Bomb : Tensile strength variation )	-	2000	-
10.1 c) 3)(Physical tests for covering -Ageing in Air Bomb : Elongation variation at break )	-	2000	-
10.1 c) 4)(Physical tests for covering - Oil Resistance : Tensile strength variation )	-	2000	-
10.1 c) 4)(Physical tests for covering - Oil Resistance : Elongation variation at break )	-	2000	-
10.1 c) 5)(Hot set test )	-	2000	-
10.1 c) 5)(Permanent set )	-	2000	-
11.1(High Voltage Test ( Water Immersion Test ))	-	2000	-
11.2(Spark Test)	-	1000	-
11.3(Static Flexibility Test)	-	1000	-
11.4(Flammability Test)	-	1000	-
12.1(Manufacturer's Identification)	-	500	-
12.2(Cable Identification)	-	500	-
12.3(Cable Code)	-	500	-
13.1(Packing )	-	500	-
13.2(Marking)	-	500	-
14(CABLE RATINGS)	-	500	-
15(VOLTAGE DROP)	-	500	-
Table 4(Copper purity test)	-	3000	-
Table 2(Oil resistance - Elongation)	-	2000	-
Table 2(Oil resistance - Tensile strength )	-	2000	-
Table 2(Ageing in air bomb - Elongation)	-	2000	-
Table 2(Ageing in air bomb - Tensile strength )	-	2000	-
Table 1 (Thickness of covering)	-	2000	-
15.1 (d)(Heat Shock Test)	-	1000	-
15.1 (d)(Hot Deformation Test)	-	2000	-
15.1 (d)(Loss Of Mass Test)	-	2000	-
10.1(b), Table 1(Thickness of covering)	-	2000	-
4(Conductor : Material )	-	500	-
5(SEPARATOR)	-	500	-
6(COVERING)	-	500	-
7(CONDUCTOR : CONSTRUCTION )	-	500	-
8(S E P A R A T O R)	-	500	-
9.1(C O V E R I N G : Application )	-	500	-
9.2(T h i c k n e s s o f C o v e r i n g)	-	1000	-
9.3(T o l e r a n c e on Thickness o f C o v e r i n g)	-	1000	-
9.4(A p p l i c a t i o n of C o v e r i n g)	-	500	-
9.5(Colour of C o v e r i n g)	-	500	-
10.1 a) 1)(Annealing test - IS 10810: Part 1)	-	1000	-
10.1 a) 2)(Conductor resistance tes - IS 10810 : Part 5)	-	1000	-
10.1 c) 1)(Physical tests for covering : Tensile strength )	-	1000	-
10.1 c) 1)(Physical tests for covering : Elongation at break )	-	1000	-
10.1 c) 2)(Physical tests for covering - Ageing in Air oven : Tensile strength variation)	-	2000	-
10.1 c) 2)(Physical tests for covering -Ageing in Air oven : Elongation at break )	-	2000	-
10.1 c) 2)(Physical tests for covering - Ageing in Air oven : Tensile strength )	-	2000	-
10.1 c) 2)(Physical tests for covering -Ageing in Air oven : Elongation variation at break )	-	2000	-
10.1 c) 3)(Physical tests for covering - Ageing in Air Bomb : Tensile strength variation )	-	2000	-
10.1 c) 3)(Physical tests for covering -Ageing in Air Bomb : Elongation variation at break )	-	2000	-
10.1 c) 4)(Physical tests for covering - Oil Resistance : Tensile strength variation )	-	2000	-
10.1 c) 4)(Physical tests for covering - Oil Resistance : Elongation variation at break )	-	2000	-
10.1 c) 5)(Hot set test )	-	1000	-
10.1 c) 5)(Permanent set )	-	1000	-
11.1(High Voltage Test ( Water Immersion Test ))	-	2000	-
11.2(Spark Test)	-	1000	-
11.3(Static Flexibility Test)	-	1000	-
11.4(Flammability Test)	-	1000	-
12.1(Manufacturer's Identification)	-	500	-
12.2(Cable Identification)	-	500	-
12.3(Cable Code)	-	500	-
13.1(Packing )	-	500	-
13.2(Marking)	-	500	-
14(CABLE RATINGS)	-	500	-
15(VOLTAGE DROP)	-	500	-
Table 4(Copper purity test)	-	5000	-
Table 2(Oil resistance - Elongation)	-	2000	-
Table 2(Oil resistance - Tensile strength )	-	2000	-
Table 2(Ageing in air bomb - Elongation)	-	2000	-
Table 2(Ageing in air bomb - Tensile strength )	-	2000	-
Table 1 (Thickness of covering)	-	1000	-
15.1 (d)(Heat Shock Test)	-	1000	-
15.1 (d)(Hot Deformation Test)	-	2000	-
15.1 (d)(Loss Of Mass Test)	-	2000	-
10.1(b), Table 1(Thickness of covering)	-	1000	-

15 Jun, 2029

-
Included w.e.f.18.06.2025

IS 398 : Part 4 (1994)

Aluminium conductors for overhead transmission purposes: Part 4 aluminium alloy stranded conductors (Aluminium - Magnesium - Silicon Type) - Specification (Third Revision)

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Freedom from Defects)	-	500	Rs. 7000/- for 7 strands, Rs. 10000/- for 19 strands, Rs. 12000/- for 37 strands and Rs. 15000/- for 61 strands
7.1 Table-1(Dimensional measurement of wires)	-	1000	-
7.2.2 Table-2, Table-4(Calculated resistance of Stranded Conductor)	-	1000	-
8.1(Joints in wires-Conductors Containing Seven Wires)	-	1000	-
8.2(Joints in wires-Conductors Containing More Than Seven Wires)	-	1000	-
9.1(Stranding)	-	500	-
9.2 Table 3(Lay Ratio of stranded conductors)	-	1000	-
9.3(Direction of Lay)	-	1000	-
9.4(Multiple layers of wires)	-	1000	-
11(Packing and Marking)	-	1000	-
12.2 Table 1(Breaking Load Test- Before Stranding)	-	2000	-
12.2 Table 1(Breaking Load Test- After Stranding)	-	2000	-
12.3 Table 1(Elongation Test- Before Stranding)	-	1000	-
12.3 Table 1(Elongation Test- After Stranding)	-	1000	-
12.4 Table 1(Resistance of Aluminium wire)	-	2000	-
9.2(Lay Ratio 24 wire layer)	-	1000	-
9.2(Lay Ratio 18 wire layer)	-	1000	-
9.2(Lay Ratio 12 wire layer)	-	1000	-
9.2(Lay Ratio 3/6 wire layer)	-	1000	-
7.2.1(Sizes)	-	500	-
Cl-7.2 (7.2.1, 7.2.2), Table-2(Stranding and Wire Dia)	-	500	-
Cl- 7.2 (7.2.1, 7.2.2), Table-2(Approx Overall Dia)	-	1000	-
Cl. 7.2 (7.2.1, 7.2.2), Table 2(Approx Mass)	-	1000	-
Cl- 7.2 (7.2.1, 7.2.2), Table-2(Calculated Maximum Resistance at 20°C)	-	1000	-
Cl- 7.2 (7.2.1, 7.2.2), Table-2(Approx Calculated Breaking Load)	-	1000	-
6.1(Freedom from Defects)	-	500	-
7.1 Table-1(Dimensional measurement of wires)	-	1000	-
7.2.2 Table-2, Table-4(Calculated resistance of Stranded Conductor)	-	1000	-
8.1(Joints in wires-Conductors Containing Seven Wires)	-	1000	-
8.2(Joints in wires-Conductors Containing More Than Seven Wires)	-	1000	-
9.1(Stranding)	-	500	-
9.2 Table 3(Lay Ratio of stranded conductors)	-	1000	-
9.3(Direction of Lay)	-	1000	-
9.4(Multiple layers of wires)	-	1000	-
11(Packing and Marking)	-	500	-
12.2 Table 1(Breaking Load Test- Before Stranding)	-	2000	-
12.2 Table 1(Breaking Load Test- After Stranding)	-	2000	-
12.3 Table 1(Elongation Test- Before Stranding)	-	1000	-
12.3 Table 1(Elongation Test- After Stranding)	-	1000	-
12.4 Table 1(Resistance of Aluminium wire)	-	2000	-
9.2(Lay Ratio 24 wire layer)	-	1000	-
9.2(Lay Ratio 18 wire layer)	-	1000	-
9.2(Lay Ratio 12 wire layer)	-	1000	-
9.2(Lay Ratio 3/6 wire layer)	-	1000	-
7.2.1(Sizes)	-	1000	-
Cl-7.2 (7.2.1, 7.2.2), Table-2(Stranding and Wire Dia)	-	1000	-
Cl- 7.2 (7.2.1, 7.2.2), Table-2(Approx Overall Dia)	-	1000	-
Cl. 7.2 (7.2.1, 7.2.2), Table 2(Approx Mass)	-	1000	-
Cl- 7.2 (7.2.1, 7.2.2), Table-2(Calculated Maximum Resistance at 20°C)	-	1000	-
Cl- 7.2 (7.2.1, 7.2.2), Table-2(Approx Calculated Breaking Load)	-	1000	-
6.1(Freedom from Defects)	-	500	-
7.1 Table-1(Dimensional measurement of wires)	-	2000	-
7.2.2 Table-2, Table-4(Calculated resistance of Stranded Conductor)	-	2000	-
8.1(Joints in wires-Conductors Containing Seven Wires)	-	1000	-
8.2(Joints in wires-Conductors Containing More Than Seven Wires)	-	1000	-
9.1(Stranding)	-	500	-
9.2 Table 3(Lay Ratio of stranded conductors)	-	1000	-
9.3(Direction of Lay)	-	1000	-
9.4(Multiple layers of wires)	-	1000	-
11(Packing and Marking)	-	500	-
12.2 Table 1(Breaking Load Test- Before Stranding)	-	1000	-
12.2 Table 1(Breaking Load Test- After Stranding)	-	2000	-
12.3 Table 1(Elongation Test- Before Stranding)	-	1000	-
12.3 Table 1(Elongation Test- After Stranding)	-	2000	-
12.4 Table 1(Resistance of Aluminium wire)	-	2000	-
9.2(Lay Ratio 24 wire layer)	-	1000	-
9.2(Lay Ratio 18 wire layer)	-	1000	-
9.2(Lay Ratio 12 wire layer)	-	1000	-
9.2(Lay Ratio 3/6 wire layer)	-	1000	-
7.2.1(Sizes)	-	1000	-
Cl-7.2 (7.2.1, 7.2.2), Table-2(Stranding and Wire Dia)	-	1000	-
Cl- 7.2 (7.2.1, 7.2.2), Table-2(Approx Overall Dia)	-	1000	-
Cl. 7.2 (7.2.1, 7.2.2), Table 2(Approx Mass)	-	1000	-
Cl- 7.2 (7.2.1, 7.2.2), Table-2(Calculated Maximum Resistance at 20°C)	-	1000	-
Cl- 7.2 (7.2.1, 7.2.2), Table-2(Approx Calculated Breaking Load)	-	1000	-

15 Jun, 2029

-
included w.e.f.18.06.2025

IS 398 : Part 2 (1996)

Aluminium conductors for overhead transmission purposes - Specification: Part 2 aluminium conuuctors, galvanized steel - Reinforced (Third Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1.1 & 13.2 Table-1 (mech)(Diameter of Aluminium Wires Before Stranding)	-	1000	-
8.1.1 & 13.2 Table 2 (mech)(Diameter of Steel Wires Before Stranding)	-	1000	-
8.1.1 & 13.2 Table-1 (mech)(Diameter of Aluminium Wires After Stranding)	-	1000	-
8.1.1 & 13.2 Table 2 (mech)(Diameter of Steel Wires After Stranding)	-	1000	-
10 (elec)(Stranding)	-	500	-
10 (elec)(Stranding)	-	500	-
10 (elec)(Stranding)	-	500	-
10 (mech)(Stranding)	-	500	-
13.3 Table 1 (mech)(Breaking Load of Aluminium Wires Before Stranding)	-	1000	-
13.3 Table 2 (mech)(Breaking Load of Steel Wires Before Stranding)	-	1000	-
13.3 Table 1 (mech)(Breaking Load of Aluminium Wires After Stranding)	-	1000	-
13.3 Table 2 (mech)(Breaking Load of Steel Wires After Stranding)	-	1000	-
13.4.1 (mech)(Ductility by Torsion Test before stranding)	-	1000	-
13.4.1 (mech)(Ductility by Torsion Test before stranding)	-	1000	-
13.4.1 (mech)(Ductility by Torsion Test after stranding)	-	1000	-
13.4.1 (mech)(Ductility by Torsion Test after stranding)	-	1000	-
13.4.2 (elec)(Ductility by Elongation Test before stranding)	-	1000	-
13.4.2 (elec)(Ductility by Elongation Test after stranding)	-	1000	-
13.5.1 (mech)(Wrapping Test Aluminium Wires Before Stranding)	-	1000	-
13.5.1 (mech)(Wrapping Test Aluminium Wires After Stranding)	-	1000	-
13.5.2 (mech)(Wrapping Test Galvanized Steel Wires Before Stranding)	-	1000	-
13.5.2 (mech)(Wrapping Test Galvanized Steel Wires After Stranding)	-	1000	-
13.6 (elec)(Resistance test-Aluminium wire before Stranding)	-	1000	-
13.6 (elec)(Resistance test-Aluminium wire after stranding)	-	1000	-
13.7.2 (chem)(Mass of Zinc coating)	-	1000	-
13.7.2 (chem)(Uniformity of Zinc coating)	-	1000	-
13.8 Table-4 (mech)(Lay Ratio- Aluminium Wire Outermost Layer)	-	1000	-
13.8 Table-4 (mech)(Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-	1000	-
13.8 Table-4 (mech)(Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-	1000	-
13.8 Table-4 (mech)(Lay Ratio- Steel Core (6 Wire Layer))	-	1000	-
13.9 (elec)(Surface condition test)	-	1000	-
13.10 (elec)(Ultimate breaking load)	-	1000	-
13.11 (elec)(Stress-strain test)	-	1000	-
13.8 Table-4 (elec)(Lay Ratio- Steel Core (6 Wire Layer))	-	1000	-
13.8 Table-4 (elec)(Lay Ratio- Steel Core (6 Wire Layer))	-	1000	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-	1000	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-	1000	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Outermost Layer)	-	1000	-
13.7.2 (elec)(Uniformity of Zinc coating)	-	1000	-
13.7.2 (elec)(Mass of Zinc coating)	-	1000	-
13.5.2 (elec)(Wrapping Test Galvanized Steel Wires After Stranding)	-	1000	-
13.5.2 (elec)(Wrapping Test Galvanized Steel Wires Before Stranding)	-	1000	-
13.5.1 (elec)(Wrapping Test Aluminium Wires After Stranding)	-	1000	-
13.5.1 (elec)(Wrapping Test Aluminium Wires Before Stranding)	-	1000	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	1000	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	1000	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	1000	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	1000	-
13.3 Table 2 (elec)(Breaking Load of Steel Wires After Stranding)	-	1000	-
13.3 Table 1 (elec)(Breaking Load of Steel Wires After Stranding)	-	1000	-
13.3 Table 2 (elec)(Breaking Load of Steel Wires Before Stranding)	-	1000	-
13.3 Table 1 (elec)(Breaking Load of Steel Wires Before Stranding)	-	1000	-
8.1.1 & 13.2 Table-1 (elec)(Diameter of Aluminium Wires Before Stranding)	-	1000	-
8.1.1 & 13.2 Table 2 (elec)(Diameter of Steel Wires Before Stranding)	-	1000	-
8.1.1 & 13.2 Table-1 (elec)(Diameter of Aluminium Wires After Stranding)	-	1000	-
8.1.1 & 13.2 Table 2 (elec)(Diameter of Steel Wires After Stranding)	-	1000	-
13.8 Table-4 (elec)(Lay Ratio- Steel Core (6 Wire Layer))	-	1000	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-	1000	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-	1000	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Outermost Layer)	-	1000	-
13.7.2 (elec)(Uniformity of Zinc coating)	-	1000	-
13.7.2 (elec)(Mass of Zinc coating)	-	1000	-
13.5.2 (elec)(Wrapping Test Galvanized Steel Wires After Stranding)	-	1000	-
13.5.2 (elec)(Wrapping Test Galvanized Steel Wires Before Stranding)	-	1000	-
13.5.1 (elec)(Wrapping Test Aluminium Wires After Stranding)	-	1000	-
13.5.1 (elec)(Wrapping Test Aluminium Wires Before Stranding)	-	1000	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	1000	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	1000	-
13.4.1 (elec)(Ductility by Torsion Test before stranding)	-	1000	-
13.4.1 (elec)(Ductility by Torsion Test before stranding)	-	1000	-
13.3 Table 2 (elec)(Breaking Load of Steel Wires After Stranding)	-	1000	-
13.3 Table 1 (elec)(Breaking Load of Aluminium Wires After Stranding)	-	1000	-
13.3 Table 2 (elec)(Breaking Load of Steel Wires Before Stranding)	-	1000	-
13.3 Table 1 (elec)(Breaking Load of Aluminium Wires Before Stranding)	-	1000	-
10 (elec)(Stranding)	-	1000	-
8.1.1 & 13.2 Table 2 (elec)(Diameter of Steel Wires After Stranding)	-	1000	-
8.1.1 & 13.2 Table-1 (elec)(Diameter of Aluminium Wires After Stranding)	-	1000	-
8.1.1 & 13.2 Table 2 (elec)(Diameter of Steel Wires Before Stranding)	-	1000	-
8.1.1 & 13.2 Table-1 (elec)(Diameter of Aluminium Wires Before Stranding)	-	1000	-
4.1(Resistivity)	-	1000	-
4.2(Density)	-	1000	-
4.3(Constant-Mass Temperature Coefficient of Resistance)	-	1000	-
4.4(Coefficient of Linear Expansion)	-	1000	-
5.1(Density)	-	1000	-
5.2(Coefficient of Linear Expansion)	-	1000	-
7(FREEDOM FROM DEFECTS)	-	1000	-
14.2(a), 8.2.1(Sizes)	-	1000	-
6.2(zinc Purity)	-	1000	-
9(Joint in wires)	-	1000	-
6.1.1(Aluminum wires shall conform to IS 5484)	-	1000	-
6.1.2(The mechanical properties of wire shall comply with the requirements given in Table 2)	-	1000	-
6.2(It shall conform to and satisfy all the requirements of IS 209)	-	1000	-
8.2.2(Calculated resistance)	-	1000	-
Cl-9.2.5(Welded joint strength)	-	1000	-
8.1.1 & 13.2 Table-1(Diameter of Aluminium Wires Before Stranding)	-	1000	-
8.1.1 & 13.2 Table 2(Diameter of Steel Wires Before Stranding)	-	1000	-
8.1.1 & 13.2 Table-1(Diameter of Aluminium Wires After Stranding)	-	1000	-
8.1.1 & 13.2 Table 2(Diameter of Steel Wires After Stranding)	-	1000	-
10(Stranding)	-	1000	-
13.3 Table 1(Breaking Load of Aluminium Wires Before Stranding)	-	1000	-
13.3 Table 2(Breaking Load of Steel Wires Before Stranding)	-	1000	-
13.3 Table 1(Breaking Load of Aluminium Wires After Stranding)	-	1000	-
13.3 Table 2(Breaking Load of Steel Wires After Stranding)	-	1000	-
13.4.1(Ductility by Torsion Test before stranding)	-	1000	-
13.4.1(Ductility by Torsion Test before stranding)	-	1000	-
13.4.1(Ductility by Torsion Test after stranding)	-	1000	-
13.4.1(Ductility by Torsion Test after stranding)	-	1000	-
13.5.1(Wrapping Test Aluminium Wires Before Stranding)	-	1000	-
13.5.1(Wrapping Test Aluminium Wires After Stranding)	-	1000	-
13.5.2(Wrapping Test Galvanized Steel Wires Before Stranding)	-	1000	-
13.5.2(Wrapping Test Galvanized Steel Wires After Stranding)	-	1000	-
13.8 Table-4(Lay Ratio- Aluminium Wire Outermost Layer)	-	1000	-
13.8 Table-4(Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-	1000	-
13.8 Table-4(Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-	1000	-
13.8 Table-4(Lay Ratio- Steel Core (6 Wire Layer))	-	1000	-
13.7(Galvanising test Dip test for uniformity of coating)	-	1000	-
13.7(Galvanising test Dip test for uniformity of coating)	-	1000	-
13.7(Weight of Zinc Coating [g/m²])	-	1000	-
13.7(Weight of Zinc Coating [g/m²])	-	1000	-
7.1(Freedom from Defects)	-	1000	-
9(Joint in Wire)	-	1000	-
8.1.1 & 13.2 Table-1 (mech)(Diameter of Aluminium Wires Before Stranding)	-	1000	-
8.1.1 & 13.2 Table 2 (mech)(Diameter of Steel Wires Before Stranding)	-	1000	-
8.1.1 & 13.2 Table-1 (mech)(Diameter of Aluminium Wires After Stranding)	-	1000	-
8.1.1 & 13.2 Table 2 (mech)(Diameter of Steel Wires After Stranding)	-	1000	-
10 (elec)(Stranding)	-	500	-
10 (elec)(Stranding)	-	500	-
10 (elec)(Stranding)	-	500	-
10 (mech)(Stranding)	-	500	-
13.3 Table 1 (mech)(Breaking Load of Aluminium Wires Before Stranding)	-	1000	-
13.3 Table 2 (mech)(Breaking Load of Steel Wires Before Stranding)	-	1000	-
13.3 Table 1 (mech)(Breaking Load of Aluminium Wires After Stranding)	-	1000	-
13.3 Table 2 (mech)(Breaking Load of Steel Wires After Stranding)	-	1000	-
13.4.1 (mech)(Ductility by Torsion Test before stranding)	-	1000	-
13.4.1 (mech)(Ductility by Torsion Test before stranding)	-	1000	-
13.4.1 (mech)(Ductility by Torsion Test after stranding)	-	1000	-
13.4.1 (mech)(Ductility by Torsion Test after stranding)	-	1000	-
13.4.2 (elec)(Ductility by Elongation Test before stranding)	-	1000	-
13.4.2 (elec)(Ductility by Elongation Test after stranding)	-	1000	-
13.5.1 (mech)(Wrapping Test Aluminium Wires Before Stranding)	-	1000	-
13.5.1 (mech)(Wrapping Test Aluminium Wires After Stranding)	-	1000	-
13.5.2 (mech)(Wrapping Test Galvanized Steel Wires Before Stranding)	-	1000	-
13.5.2 (mech)(Wrapping Test Galvanized Steel Wires After Stranding)	-	1000	-
13.6 (elec)(Resistance test-Aluminium wire before Stranding)	-	1000	-
13.6 (elec)(Resistance test-Aluminium wire after stranding)	-	1000	-
13.7.2 (chem)(Mass of Zinc coating)	-	1000	-
13.7.2 (chem)(Uniformity of Zinc coating)	-	1000	-
13.8 Table-4 (mech)(Lay Ratio- Aluminium Wire Outermost Layer)	-	1000	-
13.8 Table-4 (mech)(Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-	1000	-
13.8 Table-4 (mech)(Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-	1000	-
13.8 Table-4 (mech)(Lay Ratio- Steel Core (6 Wire Layer))	-	1000	-
13.9 (elec)(Surface condition test)	-	25000	-
13.10 (elec)(Ultimate breaking load)	-	25000	-
13.11 (elec)(Stress-strain test)	-	50000	-
13.8 Table-4 (elec)(Lay Ratio- Steel Core (6 Wire Layer))	-	1000	-
13.8 Table-4 (elec)(Lay Ratio- Steel Core (6 Wire Layer))	-	1000	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-	1000	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-	1000	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Outermost Layer)	-	1000	-
13.7.2 (elec)(Uniformity of Zinc coating)	-	1000	-
13.7.2 (elec)(Mass of Zinc coating)	-	1000	-
13.5.2 (elec)(Wrapping Test Galvanized Steel Wires After Stranding)	-	1000	-
13.5.2 (elec)(Wrapping Test Galvanized Steel Wires Before Stranding)	-	1000	-
13.5.1 (elec)(Wrapping Test Aluminium Wires After Stranding)	-	1000	-
13.5.1 (elec)(Wrapping Test Aluminium Wires Before Stranding)	-	1000	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	1000	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	1000	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	1000	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	1000	-
13.3 Table 2 (elec)(Breaking Load of Steel Wires After Stranding)	-	1000	-
13.3 Table 1 (elec)(Breaking Load of Steel Wires After Stranding)	-	1000	-
13.3 Table 2 (elec)(Breaking Load of Steel Wires Before Stranding)	-	1000	-
13.3 Table 1 (elec)(Breaking Load of Steel Wires Before Stranding)	-	1000	-
8.1.1 & 13.2 Table-1 (elec)(Diameter of Aluminium Wires Before Stranding)	-	1000	-
8.1.1 & 13.2 Table 2 (elec)(Diameter of Steel Wires Before Stranding)	-	1000	-
8.1.1 & 13.2 Table-1 (elec)(Diameter of Aluminium Wires After Stranding)	-	1000	-
8.1.1 & 13.2 Table 2 (elec)(Diameter of Steel Wires After Stranding)	-	1000	-
13.8 Table-4 (elec)(Lay Ratio- Steel Core (6 Wire Layer))	-	1000	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-	1000	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-	1000	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Outermost Layer)	-	1000	-
13.7.2 (elec)(Uniformity of Zinc coating)	-	1000	-
13.7.2 (elec)(Mass of Zinc coating)	-	1000	-
13.5.2 (elec)(Wrapping Test Galvanized Steel Wires After Stranding)	-	1000	-
13.5.2 (elec)(Wrapping Test Galvanized Steel Wires Before Stranding)	-	1000	-
13.5.1 (elec)(Wrapping Test Aluminium Wires After Stranding)	-	1000	-
13.5.1 (elec)(Wrapping Test Aluminium Wires Before Stranding)	-	1000	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	1000	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	1000	-
13.4.1 (elec)(Ductility by Torsion Test before stranding)	-	1000	-
13.4.1 (elec)(Ductility by Torsion Test before stranding)	-	1000	-
13.3 Table 2 (elec)(Breaking Load of Steel Wires After Stranding)	-	1000	-
13.3 Table 1 (elec)(Breaking Load of Aluminium Wires After Stranding)	-	1000	-
13.3 Table 2 (elec)(Breaking Load of Steel Wires Before Stranding)	-	1000	-
13.3 Table 1 (elec)(Breaking Load of Aluminium Wires Before Stranding)	-	1000	-
10 (elec)(Stranding)	-	1000	-
8.1.1 & 13.2 Table 2 (elec)(Diameter of Steel Wires After Stranding)	-	1000	-
8.1.1 & 13.2 Table-1 (elec)(Diameter of Aluminium Wires After Stranding)	-	1000	-
8.1.1 & 13.2 Table 2 (elec)(Diameter of Steel Wires Before Stranding)	-	1000	-
8.1.1 & 13.2 Table-1 (elec)(Diameter of Aluminium Wires Before Stranding)	-	1000	-
4.1(Resistivity)	-	1000	-
4.2(Density)	-	1000	-
4.3(Constant-Mass Temperature Coefficient of Resistance)	-	1000	-
4.4(Coefficient of Linear Expansion)	-	1000	-
5.1(Density)	-	1000	-
5.2(Coefficient of Linear Expansion)	-	1000	-
7(FREEDOM FROM DEFECTS)	-	1000	-
14.2(a), 8.2.1(Sizes)	-	500	-
6.2(zinc Purity)	-	2000	-
9(Joint in wires)	-	1000	-
6.1.1(Aluminum wires shall conform to IS 5484)	-	1000	-
6.1.2(The mechanical properties of wire shall comply with the requirements given in Table 2)	-	1000	-
6.2(It shall conform to and satisfy all the requirements of IS 209)	-	1000	-
8.2.2(Calculated resistance)	-	1000	-
Cl-9.2.5(Welded joint strength)	-	1000	-
8.1.1 & 13.2 Table-1(Diameter of Aluminium Wires Before Stranding)	-	1000	-
8.1.1 & 13.2 Table 2(Diameter of Steel Wires Before Stranding)	-	1000	-
8.1.1 & 13.2 Table-1(Diameter of Aluminium Wires After Stranding)	-	1000	-
8.1.1 & 13.2 Table 2(Diameter of Steel Wires After Stranding)	-	1000	-
10(Stranding)	-	500	-
13.3 Table 1(Breaking Load of Aluminium Wires Before Stranding)	-	1000	-
13.3 Table 2(Breaking Load of Steel Wires Before Stranding)	-	1000	-
13.3 Table 1(Breaking Load of Aluminium Wires After Stranding)	-	1000	-
13.3 Table 2(Breaking Load of Steel Wires After Stranding)	-	1000	-
13.4.1(Ductility by Torsion Test before stranding)	-	1000	-
13.4.1(Ductility by Torsion Test before stranding)	-	1000	-
13.4.1(Ductility by Torsion Test after stranding)	-	1000	-
13.4.1(Ductility by Torsion Test after stranding)	-	1000	-
13.5.1(Wrapping Test Aluminium Wires Before Stranding)	-	1000	-
13.5.1(Wrapping Test Aluminium Wires After Stranding)	-	1000	-
13.5.2(Wrapping Test Galvanized Steel Wires Before Stranding)	-	1000	-
13.5.2(Wrapping Test Galvanized Steel Wires After Stranding)	-	1000	-
13.8 Table-4(Lay Ratio- Aluminium Wire Outermost Layer)	-	1000	-
13.8 Table-4(Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-	1000	-
13.8 Table-4(Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-	1000	-
13.8 Table-4(Lay Ratio- Steel Core (6 Wire Layer))	-	1000	-
13.7(Galvanising test Dip test for uniformity of coating)	-	1000	-
13.7(Galvanising test Dip test for uniformity of coating)	-	1000	-
13.7(Weight of Zinc Coating [g/m²])	-	1000	-
13.7(Weight of Zinc Coating [g/m²])	-	1000	-
7.1(Freedom from Defects)	-	1000	-
9(Joint in Wire)	-	1000	-

15 Jun, 2029

-
Included w.e.f.10.07.2025 Exclusion Cl 13.9 (elec) (Surface condition test) Cl 13.10 (elec) (Ultimate breaking load) Cl 13.11 (elec) (Stress-strain test)

IS 1554 : Part 1 (1988)

Specification for pvc insulated (Heavy Duty) electric cables: Part 1 for working voltages up to and including 1100 v (Third Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(MATERIALS : CONDUCTOR)	-	500	Rs. 10000/- for single core sheathed cable, Rs. 1000/- for each additional core, Rs. 3000/- for armoured cable, Rs. 5000/- for Category C1 and Rs.10000/- for Category C2
4.1.1(INSULATION : General Purjose Insulaiion)	-	500	-
4.1.2(INSULATION : Heat Resisting Insulation)	-	500	-
5.1(MATERIALS : FILLER AND INNER SHEATH)	-	500	-
5.2(MATERIALS : FILLER AND INNER SHEATH)	-	500	-
6.1(MATERIALS : ARMGURING)	-	500	-
6.2(MATERIALS : ARMGURING)	-	500	-
7.1.1(OUTER SHEATH : For Cables with General Purpose InsuIafion)	-	500	-
7.1.2(OUTER SHEATH : For Cables with Heat Resisting InsuIalion)	-	500	-
8.1(CONSTRUCTION : CONDUCTOR)	-	500	-
8.2(CONSTRUCTION : CONDUCTOR)	-	500	-
9.1(INSULATION )	-	500	-
9.2(INSULATION : Thickness of Insulation)	-	1000	-
9.3(INSULATION :Tolerance on Thickness of Insulation)	-	1000	-
9.4(INSULATION : Application of Insulation)	-	500	-
10.1(CORE IDENTIFICATION)	-	500	-
10.2(CORE IDENTIFICATION)	-	500	-
10.3(CORE IDENTIFICATION)	-	500	-
10.3.1(Arrangement of Marking)	-	500	-
11.1(LAYING UP OF CORES)	-	500	-
11.2(LAYING UP OF CORES)	-	500	-
12.1(INNER SHEATH)	-	500	-
12.2(INNER SHEATH)	-	500	-
12.3(INNER SHEATH :Thickness of Inner Sheath)	-	1000	-
12.3.1(INNER SHEATH :Thickness of Inner Sheath)	-	1000	-
13.1.1(ARMOURING : Application)	-	500	-
13.1.2(Armouring: Coverage )	-	1000	-
13.1.3(ARMOURING : Direction of lay )	-	500	-
13.1.4(ARMOURING : Application)	-	500	-
13.2(ARMOURING : Type of Armour)	-	500	-
13.2.1(ARMOURING : Type of Armour)	-	500	-
13.3(Armouring : Dimensions -Wire Diameter)	-	1000	-
13.3(Armouring : Dimensions -Formed wire )	-	1000	-
13.4(ARMOURING : Joints)	-	500	-
13.5.1(ARMOURING : Resistance)	-	1000	-
13.5.2(ARMOURING : Resistance)	-	1000	-
13.6 a)(ARMOURING: Tensile Strength)	-	1000	-
13.6 b)(ARMOURING: Elongation )	-	1000	-
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	1000	-
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	1000	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	1000	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	1000	-
13.6 g)(ARMOURING: Resistivity)	-	1000	-
14.1(OUTER SHEATH)	-	500	-
14.2(OUTER SHEATH)	-	500	-
14.3(OUTER SHEATH : Colour )	-	500	-
14.4.1(Thickness of Outer Sheath : Unarmowed Cables)	-	1000	-
14.4.2(Thickness of Outer Sheath : Armoured Cables)	-	1000	-
15.1 a) 1)(Tests on conductor : Annealing test ( for copper ))	-	1000	-
15.1 a) 2)(Tensile test (for aluminium) - Before stranding )	-	1000	-
15.1 a) 3)(Tests on conductor : Wrapping test ( for aluminium ))	-	1000	-
15.1 a) 4)(Tests on conductor : Conductor resistance test)	-	1000	-
15.1 a) 4)(Resistance test - Neutral conductor )	-	1000	-
15.1 d)1)(Phyaical tests for insulation : Tensile Test)	-	1000	-
15.1 d)1)(Phyaical tests for insulation : Elongation )	-	1000	-
15.1 d)1)(Physical tests for sheath : Tensile stregth )	-	1000	-
15.1 d)1)(Physical tests for sheath : Elongation )	-	1000	-
15.1 d)2)(Phyaical tests for insulation- Ageing in air Oven : Tensile Test)	-	2000	-
15.1 d)2)(Phyaical tests for insulation - Ageing in air oven : Elongation )	-	2000	-
15.1 d)2)(Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	2000	-
15.1 d)2)(Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	2000	-
15.1 d)2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	2000	-
15.1 d)2)(Physical tests for outer sheath -Ageing in air oven : Elongation )	-	2000	-
15.1 d)2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	2000	-
15.1 d)2)(Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	2000	-
15.1 d)3)(Phyaical tests for insulation : Shrinkage )	-	1000	-
15.1 d)3)(Phyaical tests for insulation : Shrinkage - Crack observed )	-	1000	-
15.1 d)3)(Phyaical tests for Sheath : Shrinkage )	-	1000	-
15.1 d)3)(Phyaical tests for Sheath : Shrinkage - Crack observed )	-	1000	-
15.1 d)4)(Hot deformation : Insulation )	-	1000	-
15.1 d)4)(Hot deformation : Sheath )	-	1000	-
15.1 d)5)( Loss of mass in air oven- Insulation )	-	2000	-
15.1 d)5)( Loss of mass in air oven- sheath )	-	2000	-
15.1 d)6)(Heat shock test- Insulation )	-	1000	-
15.1 d)6)(Heat shock test- sheath )	-	1000	-
15.1 d)7)(Thermal stability- insulation )	-	1000	-
15.1 d)7)(Thermal stability- Sheath )	-	1000	-
15.1 e)(Insulation resistance test : Volume Resistivity )	-	1000	-
15.1 e)(Insulation resistance test : IR Constant )	-	1000	-
15.1 f)(High voltage test ( water immersion test ))	-	2000	-
15.1 g)(High voltage test at room temperature)	-	1000	-
15.1 g)(High voltage test at room temperature)	-	1000	-
15.4 a)(Cold bend test- Insulation ( Optional test))	-	1000	-
15.4 a)(Cold bend test- Sheath ( Optional test))	-	1000	-
15.4 b)(Cold impact test- Insulation ( Optional test))	-	1000	-
15.4 b)(Cold impact test- Sheath ( Optional test))	-	1000	-
15.4 c)(Armour resistance test ( for other than mining cables ).- Optional test )	-	1000	-
16.1(DETAILS OF TESTS : General)	-	500	-
16.2(DETAILS OF TESTS : High Voltage Test at Room Temperature)	-	1000	-
16.3.1(High Voltage Test ( Water Immersion Test ) : a.c. Test)	-	2000	-
16.3.2(High Voltage Test ( Water Immersion Test ) : d.c. Test)	-	3000	-
16.4(Flammability Test)	-	1000	-
16.5(Oxygen Index Test)	-	3000	-
16.6(Flame Retardance Test on Single Cables)	-	1000	-
16.7(Flame Retardance Test on Bunched Cables)	-	5000	-
16.9(Test for Halogen Acid Gas Evolution)	-	3000	-
16.1(Temperature Index)	-	3000	-
17.1(IDENTIFICATION : Manufacturer’s Identification)	-	500	-
17.2(IDENTIFICATION : Cable Identification)	-	500	-
17.2.1(IDENTIFICATION : Cable Identification)	-	500	-
17.3(IDENTIFICATION : Cable Code)	-	500	-
15.1.e(Insulation resistance Test- Insulation resistance At Maximum rated temperature temperature)	-	1000	-
15.1.e(Insulation resistance Test- Insulation resistance constant At Room temperature)	-	1000	-
15.1.e(Insulation resistance Test- Volume Resistivity At Maximum rated temperature temperature)	-	1000	-
15.1.e(Insulation resistance Test- Volume Resistivity At Room temperature)	-	1000	-
16.4(Flammability Test- Un affected portion)	-	1000	-
16.4(Flammability Test- Period of Burning)	-	1000	-
9.3(Minimum Thickness of Reduce core insulation)	-	1000	-
9.2(Thickness of Reduce core insulation)	-	1000	-
3.1 Table 2 IS 8130(Number of wires in the conductor)	-	500	-
Cl No. 16.10(Smoke density test)	-	2000	-
Cl No. 16.8(Test for specific optical density of smoke)	-	3000	-
Table 4(Copper purity test)	-	5000	-
Cl.8(Conductor, Number of wires.)	-	500	-
Cl.8(Conductor, Number of wires.)	-	500	-
Cl.8(Flexibility class)	-	1000	-
[(Cl.15), (d), 2](After ageing, Elongation of Sheath [Percentage])	-	2000	-
15.1 a) 2)(Tensile test (for aluminium) - After stranding )	-	2000	-
Cl No. 16.10(Smoke density test)	-	3000	-
Cl No. 16.8(Test for specific optical density of smoke)	-	3000	-
Table 4(Copper purity test)	-	5000	-
Cl.8(Conductor, Number of wires.)	-	500	-
Cl.8(Conductor, Number of wires.)	-	500	-
Cl.8(Flexibility class)	-	500	-
[(Cl.15), (d), 2](After ageing, Elongation of Sheath [Percentage])	-	2000	-
Cl No. 16.10(Smoke density test)	-	3000	-
Cl No. 16.8(Test for specific optical density of smoke)	-	3000	-
Table 4(Copper purity test)	-	5000	-
Cl.8(Conductor, Number of wires.)	-	500	-
Cl.8(Conductor, Number of wires.)	-	500	-
Cl.8(Flexibility class)	-	500	-
[(Cl.15), (d), 2](After ageing, Elongation of Sheath [Percentage])	-	2000	-
Cl No. 16.10(Smoke density test)	-	3000	-
Cl No. 16.8(Test for specific optical density of smoke)	-	3000	-
Table 4(Copper purity test)	-	5000	-
Cl.8(Conductor, Number of wires.)	-	500	-
Cl.8(Conductor, Number of wires.)	-	500	-
Cl.8(Flexibility class)	-	500	-
[(Cl.15), (d), 2](After ageing, Elongation of Sheath [Percentage])	-	2000	-

15 Jun, 2029

-
Included w.e.f.16.07.2025

IS 7098 : Part 1 (1988)

Specification for crosslinked polyethylene insulated pvc sheathed cables: Part 1 for working voltages up to and including 1100 volts (First Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(CONDUCTOR: MATERIALS)	-	500	Rs.10000/- for single core sheathed cable, Rs.1000/- for Each additional core, Rs.3000/- for armoured cable, Rs.5000/- for category C1 and Rs.10000/- for category C2
4(INSULATION : MATERIALS)	-	500	-
5.1(FILLER AND INNER SHEATH)	-	500	-
5.2(FILLER AND INNER SHEATH)	-	500	-
6(ARMOURING)	-	500	-
7(OUTER SHEATH)	-	500	-
8.1(CONDUCTOR: CONSTRUCTION)	-	500	-
8.2(PROTECTIVE BARRIER)	-	500	-
8.3(SIZE OF NEUTRAL CONDUCTOR)	-	500	-
9.1(Insulation Applied by extrusicn)	-	500	-
9.2(Thickness of Insulation - Average)	-	1000	-
9.3(Thickness of Insulation - Minimum)	-	1000	-
9.4(Application of Insulation)	-	500	-
10.1(Core Identification)	-	500	-
10.2(Core Identification- Neutral)	-	500	-
10.3(Core Identification by number )	-	500	-
10.4(Core Identification by number - Neutral )	-	500	-
11(LAVING UP OF CORES)	-	500	-
12.1 & 12.2(Inner sheath : Application)	-	500	-
12.3(Thickness of Inner Sheath)	-	1000	-
13.1(Armouring: Application)	-	500	-
13.1.2(Armouring: Coverage )	-	1000	-
13.1.3(Armouring: Direction of Lay )	-	1000	-
13.2(Type of armour )	-	500	-
13.3(Armouring : Dimensions -Wire Diameter)	-	1000	-
13.3(Armouring : Dimensions -Formed wire )	-	1000	-
13.4(Armour: Joint)	-	5000	-
13.5(Armouring : Resistance Test)	-	1000	-
13.6 a)(ARMOURING: Tensile Strength)	-	1000	-
13.6 b)(ARMOURING: Elongation )	-	1000	-
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	1000	-
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	1000	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	1000	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	1000	-
13.6 g)(ARMOURING: Resistivity)	-	1000	-
14.1(Outer Sheath : Application)	-	500	-
14.2(Colour of outer sheath)	-	500	-
14.3(Thickness of outer sheath - AVERAGE)	-	1000	-
14.3(Thickness of outer sheath - minimum)	-	1000	-
15.1 a) i)(Annealing Test ( For copper wire ) )	-	1000	-
15.1 a) ii)(Tensile test (for aluminium) - Before stranding )	-	1000	-
15.1 a) ii)(Tensile test (for aluminium) - After stranding )	-	1000	-
15.1 a) iii)(Wrapping test (for aluminium))	-	1000	-
15.1 a) iv)(Resistance test - Main conductor)	-	1000	-
15.1 a) iv)(Resistance test - Neutral conductor)	-	1000	-
15.1 d) i) (Phyaical tests for insulation : Tensile Test)	-	1000	-
15.1 d) i) (Phyaical tests for insulation : Elongation)	-	1000	-
15.1 d) ii) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	2000	-
15.1 d) ii) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	2000	-
15.1 d) iii) (Phyaical tests for insulation : Hot set )	-	1000	-
15.1 d) iii) (Phyaical tests for insulation : Permanent set )	-	1000	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage )	-	1000	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage - Crack observed )	-	1000	-
15.1 d) v) (Insulation: Waterabsorption(gravimetric))	-	4000	-
15.1 e) i) (Physical tests for outer sheath : Tensile stregth)	-	1000	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation )	-	2000	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	2000	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	2000	-
15.1 e) iii) (Sheath: Loss of mass in air oven)	-	2000	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage )	-	1000	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-	1000	-
15.1 e) v) (Sheath : Hot deformation)	-	1000	-
15.1 e) vi) (Sheath : Heat shock test)	-	1000	-
15.1 e) vii) (Sheath : Thermalstability)	-	1000	-
15.1 f)(INSULATION RESISTANCE TEST : Volume resistivity )	-	1000	-
16.2(HIGH VOLTAGE TEST )	-	1000	-
16.3(FLAMMABILITY TEST : Period of Burning )	-	1000	-
16.3(FLAMMABILITY TEST : Unaffected length )	-	1000	-
16.9(Oxygen Index Test)	-	2000	-
16.1(Flame Retardance Test on Single Cables)	-	1000	-
16.11(Flame Retardance Test on Bunched Cables)	-	5000	-
16.13(Test for Halogen Acid Gas Evolution)	-	2000	-
16.14(Temperature Index)	-	2000	-
17.1(Manufacturer'. identification)	-	500	-
17.2(cable Indentification )	-	500	-
17.3(cable Code )	-	500	-
15.4 (a)(Cold bend)	-	1000	-
15.4 (b)(Cold impact)	-	1000	-
Table 1(Ageing in air oven - Elongation on Insulation)	-	2000	-
Table 1(Ageing in air oven - Tensile strength on Insulation)	-	2000	-
Table 1(Ageing in air oven - Elongation on Insulation)	-	2000	-
Table 1(Ageing in air oven - Tensile strength on Insulation)	-	2000	-
Table 4(Copper purity test)	-	2000	-
Cl No. 16.15(Smoke density test)	-	2000	-
Table 2(Cold Impact test for Outer sheath)	-	1000	-
Table 2(Cold bend test for Outer sheath)	-	1000	-
Cl 16(Halogen Acid Gas Test)	-	2000	-
Cl 16(Halogen Acid Gas Test)	-	2000	-
Cl 16(Halogen Acid Gas Test)	-	2000	-
Cl.8(Conductor)	-	500	-
Cl.8(Conductor)	-	500	-
Cl.8(Conductor)	-	500	-
Cl.15.4(Cold Bend Test (for outer sheath))	-	500	-
Cl.15.4(Cold Impact Test (For outer sheath))	-	1000	-
Cl.13.5.1 and Table 7(Resistance Test for Armouring (other than mining Cables))	-	1000	-
15.1 e) i) (Physical tests for outer sheath : Elongation)	-	1000	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	2000	-
3(CONDUCTOR: MATERIALS)	-	500	-
4(INSULATION : MATERIALS)	-	500	-
5.1(FILLER AND INNER SHEATH)	-	500	-
5.2(FILLER AND INNER SHEATH)	-	500	-
6(ARMOURING)	-	500	-
7(OUTER SHEATH)	-	500	-
8.1(CONDUCTOR: CONSTRUCTION)	-	500	-
8.2(PROTECTIVE BARRIER)	-	500	-
8.3(SIZE OF NEUTRAL CONDUCTOR)	-	500	-
9.1(Insulation Applied by extrusicn)	-	500	-
9.2(Thickness of Insulation - Average)	-	1000	-
9.3(Thickness of Insulation - Minimum)	-	1000	-
9.4(Application of Insulation)	-	500	-
10.1(Core Identification)	-	500	-
10.2(Core Identification- Neutral)	-	500	-
10.3(Core Identification by number )	-	500	-
10.4(Core Identification by number - Neutral )	-	500	-
11(LAVING UP OF CORES)	-	500	-
12.1 & 12.2(Inner sheath : Application)	-	500	-
12.3(Thickness of Inner Sheath)	-	1000	-
13.1(Armouring: Application)	-	500	-
13.1.2(Armouring: Coverage )	-	1000	-
13.1.3(Armouring: Direction of Lay )	-	500	-
13.2(Type of armour )	-	500	-
13.3(Armouring : Dimensions -Wire Diameter)	-	1000	-
13.3(Armouring : Dimensions -Formed wire )	-	1000	-
13.4(Armour: Joint)	-	500	-
13.5(Armouring : Resistance Test)	-	1000	-
13.6 a)(ARMOURING: Tensile Strength)	-	1000	-
13.6 b)(ARMOURING: Elongation )	-	1000	-
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	1000	-
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	1000	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	1000	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	1000	-
13.6 g)(ARMOURING: Resistivity)	-	1000	-
14.1(Outer Sheath : Application)	-	1000	-
14.2(Colour of outer sheath)	-	1000	-
14.3(Thickness of outer sheath - AVERAGE)	-	1000	-
14.3(Thickness of outer sheath - minimum)	-	1000	-
15.1 a) i)(Annealing Test ( For copper wire ) )	-	1000	-
15.1 a) ii)(Tensile test (for aluminium) - Before stranding )	-	1000	-
15.1 a) ii)(Tensile test (for aluminium) - After stranding )	-	1000	-
15.1 a) iii)(Wrapping test (for aluminium))	-	1000	-
15.1 a) iv)(Resistance test - Main conductor)	-	1000	-
15.1 a) iv)(Resistance test - Neutral conductor)	-	1000	-
15.1 d) i) (Phyaical tests for insulation : Tensile Test)	-	1000	-
15.1 d) i) (Phyaical tests for insulation : Elongation)	-	1000	-
15.1 d) ii) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	2000	-
15.1 d) ii) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	2000	-
15.1 d) iii) (Phyaical tests for insulation : Hot set )	-	1000	-
15.1 d) iii) (Phyaical tests for insulation : Permanent set )	-	1000	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage )	-	1000	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage - Crack observed )	-	1000	-
15.1 d) v) (Insulation: Waterabsorption(gravimetric))	-	5000	-
15.1 e) i) (Physical tests for outer sheath : Tensile stregth)	-	1000	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation )	-	2000	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	2000	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	2000	-
15.1 e) iii) (Sheath: Loss of mass in air oven)	-	2000	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage )	-	1000	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-	1000	-
15.1 e) v) (Sheath : Hot deformation)	-	1000	-
15.1 e) vi) (Sheath : Heat shock test)	-	1000	-
15.1 e) vii) (Sheath : Thermalstability)	-	1000	-
15.1 f)(INSULATION RESISTANCE TEST : Volume resistivity )	-	1000	-
16.2(HIGH VOLTAGE TEST )	-	1000	-
16.3(FLAMMABILITY TEST : Period of Burning )	-	1000	-
16.3(FLAMMABILITY TEST : Unaffected length )	-	1000	-
16.9(Oxygen Index Test)	-	2000	-
16.1(Flame Retardance Test on Single Cables)	-	1000	-
16.11(Flame Retardance Test on Bunched Cables)	-	5000	-
16.13(Test for Halogen Acid Gas Evolution)	-	2000	-
16.14(Temperature Index)	-	2000	-
17.1(Manufacturer'. identification)	-	500	-
17.2(cable Indentification )	-	500	-
17.3(cable Code )	-	500	-
15.4 (a)(Cold bend)	-	1000	-
15.4 (b)(Cold impact)	-	1000	-
Table 1(Ageing in air oven - Elongation on Insulation)	-	2000	-
Table 1(Ageing in air oven - Tensile strength on Insulation)	-	2000	-
Table 1(Ageing in air oven - Elongation on Insulation)	-	2000	-
Table 1(Ageing in air oven - Tensile strength on Insulation)	-	2000	-
Table 4(Copper purity test)	-	5000	-
Cl No. 16.15(Smoke density test)	-	2000	-
Table 2(Cold Impact test for Outer sheath)	-	1000	-
Table 2(Cold bend test for Outer sheath)	-	1000	-
Cl 16(Halogen Acid Gas Test)	-	2000	-
Cl 16(Halogen Acid Gas Test)	-	2000	-
Cl 16(Halogen Acid Gas Test)	-	2000	-
Cl.8(Conductor)	-	500	-
Cl.8(Conductor)	-	500	-
Cl.8(Conductor)	-	500	-
Cl.15.4(Cold Bend Test (for outer sheath))	-	1000	-
Cl.15.4(Cold Impact Test (For outer sheath))	-	1000	-
Cl.13.5.1 and Table 7(Resistance Test for Armouring (other than mining Cables))	-	1000	-
15.1 e) i) (Physical tests for outer sheath : Elongation)	-	1000	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	2000	-
3(CONDUCTOR: MATERIALS)	-	500	-
4(INSULATION : MATERIALS)	-	500	-
5.1(FILLER AND INNER SHEATH)	-	500	-
5.2(FILLER AND INNER SHEATH)	-	500	-
6(ARMOURING)	-	500	-
7(OUTER SHEATH)	-	500	-
8.1(CONDUCTOR: CONSTRUCTION)	-	500	-
8.2(PROTECTIVE BARRIER)	-	500	-
8.3(SIZE OF NEUTRAL CONDUCTOR)	-	500	-
9.1(Insulation Applied by extrusicn)	-	500	-
9.2(Thickness of Insulation - Average)	-	1000	-
9.3(Thickness of Insulation - Minimum)	-	1000	-
9.4(Application of Insulation)	-	500	-
10.1(Core Identification)	-	500	-
10.2(Core Identification- Neutral)	-	500	-
10.3(Core Identification by number )	-	500	-
10.4(Core Identification by number - Neutral )	-	500	-
11(LAVING UP OF CORES)	-	500	-
12.1 & 12.2(Inner sheath : Application)	-	500	-
12.3(Thickness of Inner Sheath)	-	1000	-
13.1(Armouring: Application)	-	500	-
13.1.2(Armouring: Coverage )	-	1000	-
13.1.3(Armouring: Direction of Lay )	-	500	-
13.2(Type of armour )	-	500	-
13.3(Armouring : Dimensions -Wire Diameter)	-	1000	-
13.3(Armouring : Dimensions -Formed wire )	-	1000	-
13.4(Armour: Joint)	-	500	-
13.5(Armouring : Resistance Test)	-	1000	-
13.6 a)(ARMOURING: Tensile Strength)	-	1000	-
13.6 b)(ARMOURING: Elongation )	-	1000	-
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	1000	-
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	1000	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	1000	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	1000	-
13.6 g)(ARMOURING: Resistivity)	-	1000	-
14.1(Outer Sheath : Application)	-	500	-
14.2(Colour of outer sheath)	-	500	-
14.3(Thickness of outer sheath - AVERAGE)	-	1000	-
14.3(Thickness of outer sheath - minimum)	-	1000	-
15.1 a) i)(Annealing Test ( For copper wire ) )	-	1000	-
15.1 a) ii)(Tensile test (for aluminium) - Before stranding )	-	1000	-
15.1 a) ii)(Tensile test (for aluminium) - After stranding )	-	1000	-
15.1 a) iii)(Wrapping test (for aluminium))	-	1000	-
15.1 a) iv)(Resistance test - Main conductor)	-	1000	-
15.1 a) iv)(Resistance test - Neutral conductor)	-	1000	-
15.1 d) i) (Phyaical tests for insulation : Tensile Test)	-	1000	-
15.1 d) i) (Phyaical tests for insulation : Elongation)	-	1000	-
15.1 d) ii) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	2000	-
15.1 d) ii) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	2000	-
15.1 d) iii) (Phyaical tests for insulation : Hot set )	-	2000	-
15.1 d) iii) (Phyaical tests for insulation : Permanent set )	-	2000	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage )	-	1000	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage - Crack observed )	-	1000	-
15.1 d) v) (Insulation: Waterabsorption(gravimetric))	-	5000	-
15.1 e) i) (Physical tests for outer sheath : Tensile stregth)	-	1000	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation )	-	2000	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	2000	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	2000	-
15.1 e) iii) (Sheath: Loss of mass in air oven)	-	2000	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage )	-	1000	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-	1000	-
15.1 e) v) (Sheath : Hot deformation)	-	1000	-
15.1 e) vi) (Sheath : Heat shock test)	-	1000	-
15.1 e) vii) (Sheath : Thermalstability)	-	1000	-
15.1 f)(INSULATION RESISTANCE TEST : Volume resistivity )	-	1000	-
16.2(HIGH VOLTAGE TEST )	-	2000	-
16.3(FLAMMABILITY TEST : Period of Burning )	-	1000	-
16.3(FLAMMABILITY TEST : Unaffected length )	-	1000	-
16.9(Oxygen Index Test)	-	5000	-
16.1(Flame Retardance Test on Single Cables)	-	1000	-
16.11(Flame Retardance Test on Bunched Cables)	-	5000	-
16.13(Test for Halogen Acid Gas Evolution)	-	3000	-
16.14(Temperature Index)	-	5000	-
17.1(Manufacturer'. identification)	-	500	-
17.2(cable Indentification )	-	500	-
17.3(cable Code )	-	500	-
15.4 (a)(Cold bend)	-	1000	-
15.4 (b)(Cold impact)	-	1000	-
Table 1(Ageing in air oven - Elongation on Insulation)	-	2000	-
Table 1(Ageing in air oven - Tensile strength on Insulation)	-	2000	-
Table 1(Ageing in air oven - Elongation on Insulation)	-	2000	-
Table 1(Ageing in air oven - Tensile strength on Insulation)	-	2000	-
Table 4(Copper purity test)	-	5000	-
Cl No. 16.15(Smoke density test)	-	5000	-
Table 2(Cold Impact test for Outer sheath)	-	1000	-
Table 2(Cold bend test for Outer sheath)	-	1000	-
Cl 16(Halogen Acid Gas Test)	-	3000	-
Cl 16(Halogen Acid Gas Test)	-	3000	-
Cl 16(Halogen Acid Gas Test)	-	3000	-
Cl.8(Conductor)	-	500	-
Cl.8(Conductor)	-	500	-
Cl.8(Conductor)	-	500	-
Cl.15.4(Cold Bend Test (for outer sheath))	-	1000	-
Cl.15.4(Cold Impact Test (For outer sheath))	-	1000	-
Cl.13.5.1 and Table 7(Resistance Test for Armouring (other than mining Cables))	-	1000	-
15.1 e) i) (Physical tests for outer sheath : Elongation)	-	1000	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	2000	-
3(CONDUCTOR: MATERIALS)	-	500	-
4(INSULATION : MATERIALS)	-	500	-
5.1(FILLER AND INNER SHEATH)	-	500	-
5.2(FILLER AND INNER SHEATH)	-	500	-
6(ARMOURING)	-	500	-
7(OUTER SHEATH)	-	500	-
8.1(CONDUCTOR: CONSTRUCTION)	-	500	-
8.2(PROTECTIVE BARRIER)	-	500	-
8.3(SIZE OF NEUTRAL CONDUCTOR)	-	500	-
9.1(Insulation Applied by extrusicn)	-	500	-
9.2(Thickness of Insulation - Average)	-	1000	-
9.3(Thickness of Insulation - Minimum)	-	1000	-
9.4(Application of Insulation)	-	500	-
10.1(Core Identification)	-	500	-
10.2(Core Identification- Neutral)	-	500	-
10.3(Core Identification by number )	-	500	-
10.4(Core Identification by number - Neutral )	-	500	-
11(LAVING UP OF CORES)	-	500	-
12.1 & 12.2(Inner sheath : Application)	-	500	-
12.3(Thickness of Inner Sheath)	-	1000	-
13.1(Armouring: Application)	-	500	-
13.1.2(Armouring: Coverage )	-	1000	-
13.1.3(Armouring: Direction of Lay )	-	500	-
13.2(Type of armour )	-	500	-
13.3(Armouring : Dimensions -Wire Diameter)	-	1000	-
13.3(Armouring : Dimensions -Formed wire )	-	1000	-
13.4(Armour: Joint)	-	1000	-
13.5(Armouring : Resistance Test)	-	1000	-
13.6 a)(ARMOURING: Tensile Strength)	-	1000	-
13.6 b)(ARMOURING: Elongation )	-	1000	-
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	1000	-
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	1000	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	1000	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	1000	-
13.6 g)(ARMOURING: Resistivity)	-	1000	-
14.1(Outer Sheath : Application)	-	500	-
14.2(Colour of outer sheath)	-	500	-
14.3(Thickness of outer sheath - AVERAGE)	-	1000	-
14.3(Thickness of outer sheath - minimum)	-	1000	-
15.1 a) i)(Annealing Test ( For copper wire ) )	-	1000	-
15.1 a) ii)(Tensile test (for aluminium) - Before stranding )	-	1000	-
15.1 a) ii)(Tensile test (for aluminium) - After stranding )	-	1000	-
15.1 a) iii)(Wrapping test (for aluminium))	-	1000	-
15.1 a) iv)(Resistance test - Main conductor)	-	1000	-
15.1 a) iv)(Resistance test - Neutral conductor)	-	1000	-
15.1 d) i) (Phyaical tests for insulation : Tensile Test)	-	1000	-
15.1 d) i) (Phyaical tests for insulation : Elongation)	-	1000	-
15.1 d) ii) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	2000	-
15.1 d) ii) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	2000	-
15.1 d) iii) (Phyaical tests for insulation : Hot set )	-	2000	-
15.1 d) iii) (Phyaical tests for insulation : Permanent set )	-	2000	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage )	-	1000	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage - Crack observed )	-	1000	-
15.1 d) v) (Insulation: Waterabsorption(gravimetric))	-	5000	-
15.1 e) i) (Physical tests for outer sheath : Tensile stregth)	-	1000	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation )	-	2000	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	2000	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	2000	-
15.1 e) iii) (Sheath: Loss of mass in air oven)	-	2000	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage )	-	1000	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-	1000	-
15.1 e) v) (Sheath : Hot deformation)	-	1000	-
15.1 e) vi) (Sheath : Heat shock test)	-	1000	-
15.1 e) vii) (Sheath : Thermalstability)	-	1000	-
15.1 f)(INSULATION RESISTANCE TEST : Volume resistivity )	-	1000	-
16.2(HIGH VOLTAGE TEST )	-	2000	-
16.3(FLAMMABILITY TEST : Period of Burning )	-	1000	-
16.3(FLAMMABILITY TEST : Unaffected length )	-	1000	-
16.9(Oxygen Index Test)	-	5000	-
16.1(Flame Retardance Test on Single Cables)	-	1000	-
16.11(Flame Retardance Test on Bunched Cables)	-	5000	-
16.13(Test for Halogen Acid Gas Evolution)	-	3000	-
16.14(Temperature Index)	-	5000	-
17.1(Manufacturer'. identification)	-	500	-
17.2(cable Indentification )	-	500	-
17.3(cable Code )	-	500	-
15.4 (a)(Cold bend)	-	1000	-
15.4 (b)(Cold impact)	-	1000	-
Table 1(Ageing in air oven - Elongation on Insulation)	-	2000	-
Table 1(Ageing in air oven - Tensile strength on Insulation)	-	2000	-
Table 1(Ageing in air oven - Elongation on Insulation)	-	2000	-
Table 1(Ageing in air oven - Tensile strength on Insulation)	-	2000	-
Table 4(Copper purity test)	-	5000	-
Cl No. 16.15(Smoke density test)	-	5000	-
Table 2(Cold Impact test for Outer sheath)	-	1000	-
Table 2(Cold bend test for Outer sheath)	-	1000	-
Cl 16(Halogen Acid Gas Test)	-	3000	-
Cl 16(Halogen Acid Gas Test)	-	3000	-
Cl 16(Halogen Acid Gas Test)	-	3000	-
Cl.8(Conductor)	-	500	-
Cl.8(Conductor)	-	500	-
Cl.8(Conductor)	-	500	-
Cl.15.4(Cold Bend Test (for outer sheath))	-	1000	-
Cl.15.4(Cold Impact Test (For outer sheath))	-	1000	-
Cl.13.5.1 and Table 7(Resistance Test for Armouring (other than mining Cables))	-	1000	-
15.1 e) i) (Physical tests for outer sheath : Elongation)	-	1000	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	2000	-
3(CONDUCTOR: MATERIALS)	-	500	-
4(INSULATION : MATERIALS)	-	500	-
5.1(FILLER AND INNER SHEATH)	-	500	-
5.2(FILLER AND INNER SHEATH)	-	500	-
6(ARMOURING)	-	500	-
7(OUTER SHEATH)	-	500	-
8.1(CONDUCTOR: CONSTRUCTION)	-	500	-
8.2(PROTECTIVE BARRIER)	-	500	-
8.3(SIZE OF NEUTRAL CONDUCTOR)	-	500	-
9.1(Insulation Applied by extrusicn)	-	500	-
9.2(Thickness of Insulation - Average)	-	1000	-
9.3(Thickness of Insulation - Minimum)	-	1000	-
9.4(Application of Insulation)	-	500	-
10.1(Core Identification)	-	500	-
10.2(Core Identification- Neutral)	-	500	-
10.3(Core Identification by number )	-	500	-
10.4(Core Identification by number - Neutral )	-	500	-
11(LAVING UP OF CORES)	-	500	-
12.1 & 12.2(Inner sheath : Application)	-	500	-
12.3(Thickness of Inner Sheath)	-	1000	-
13.1(Armouring: Application)	-	500	-
13.1.2(Armouring: Coverage )	-	1000	-
13.1.3(Armouring: Direction of Lay )	-	500	-
13.2(Type of armour )	-	500	-
13.3(Armouring : Dimensions -Wire Diameter)	-	1000	-
13.3(Armouring : Dimensions -Formed wire )	-	1000	-
13.4(Armour: Joint)	-	500	-
13.5(Armouring : Resistance Test)	-	1000	-
13.6 a)(ARMOURING: Tensile Strength)	-	1000	-
13.6 b)(ARMOURING: Elongation )	-	1000	-
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	1000	-
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	1000	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	1000	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	1000	-
13.6 g)(ARMOURING: Resistivity)	-	1000	-
14.1(Outer Sheath : Application)	-	500	-
14.2(Colour of outer sheath)	-	500	-
14.3(Thickness of outer sheath - AVERAGE)	-	1000	-
14.3(Thickness of outer sheath - minimum)	-	1000	-
15.1 a) i)(Annealing Test ( For copper wire ) )	-	1000	-
15.1 a) ii)(Tensile test (for aluminium) - Before stranding )	-	1000	-
15.1 a) ii)(Tensile test (for aluminium) - After stranding )	-	1000	-
15.1 a) iii)(Wrapping test (for aluminium))	-	1000	-
15.1 a) iv)(Resistance test - Main conductor)	-	1000	-
15.1 a) iv)(Resistance test - Neutral conductor)	-	1000	-
15.1 d) i) (Phyaical tests for insulation : Tensile Test)	-	1000	-
15.1 d) i) (Phyaical tests for insulation : Elongation)	-	1000	-
15.1 d) ii) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	3000	-
15.1 d) ii) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	3000	-
15.1 d) iii) (Phyaical tests for insulation : Hot set )	-	1000	-
15.1 d) iii) (Phyaical tests for insulation : Permanent set )	-	1000	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage )	-	1000	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage - Crack observed )	-	1000	-
15.1 d) v) (Insulation: Waterabsorption(gravimetric))	-	3000	-
15.1 e) i) (Physical tests for outer sheath : Tensile stregth)	-	1000	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation )	-	3000	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	3000	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	3000	-
15.1 e) iii) (Sheath: Loss of mass in air oven)	-	3000	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage )	-	1000	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-	1000	-
15.1 e) v) (Sheath : Hot deformation)	-	1000	-
15.1 e) vi) (Sheath : Heat shock test)	-	1000	-
15.1 e) vii) (Sheath : Thermalstability)	-	1000	-
15.1 f)(INSULATION RESISTANCE TEST : Volume resistivity )	-	1000	-
16.2(HIGH VOLTAGE TEST )	-	1000	-
16.3(FLAMMABILITY TEST : Period of Burning )	-	1000	-
16.3(FLAMMABILITY TEST : Unaffected length )	-	1000	-
16.9(Oxygen Index Test)	-	3000	-
16.1(Flame Retardance Test on Single Cables)	-	3000	-
16.11(Flame Retardance Test on Bunched Cables)	-	5000	-
16.13(Test for Halogen Acid Gas Evolution)	-	3000	-
16.14(Temperature Index)	-	3000	-
17.1(Manufacturer'. identification)	-	500	-
17.2(cable Indentification )	-	500	-
17.3(cable Code )	-	500	-
15.4 (a)(Cold bend)	-	1000	-
15.4 (b)(Cold impact)	-	1000	-
Table 1(Ageing in air oven - Elongation on Insulation)	-	3000	-
Table 1(Ageing in air oven - Tensile strength on Insulation)	-	3000	-
Table 1(Ageing in air oven - Elongation on Insulation)	-	3000	-
Table 1(Ageing in air oven - Tensile strength on Insulation)	-	3000	-
Table 4(Copper purity test)	-	5000	-
Cl No. 16.15(Smoke density test)	-	2000	-
Table 2(Cold Impact test for Outer sheath)	-	1000	-
Table 2(Cold bend test for Outer sheath)	-	1000	-
Cl 16(Halogen Acid Gas Test)	-	3000	-
Cl 16(Halogen Acid Gas Test)	-	3000	-
Cl 16(Halogen Acid Gas Test)	-	3000	-
Cl.8(Conductor)	-	500	-
Cl.8(Conductor)	-	500	-
Cl.8(Conductor)	-	500	-
Cl.15.4(Cold Bend Test (for outer sheath))	-	1000	-
Cl.15.4(Cold Impact Test (For outer sheath))	-	1000	-
Cl.13.5.1 and Table 7(Resistance Test for Armouring (other than mining Cables))	-	1000	-
15.1 e) i) (Physical tests for outer sheath : Elongation)	-	1000	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	3000	-

15 Jun, 2029

-
Included w.e.f.23.06.2025

IS 694 (2010)

Polyvinyl chloride insulated unsheathed and sheathed cables/cords with rigid and flexible conductor for rated voltages up to and including 450/750 v (Fourth Revision)

9500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
13(Cable code)	-	500	9500/- for single core, and 1000/- for each Additional core, 4000/- for category 02, 4000/- for category FR, 8000/- for category FR-LSH
11.2(Legibility)	-	500	-
11.1(Durability)	-	500	-
11(Identification)	-	500	-
10.9(Additional ageing test (OU cables only) -HV test (at 60±3oC))	-	5000	-
10.4(Flammability test- Unaffected portion)	-	1000	-
10.4(Flammability test-Burning after flame removal)	-	1000	-
table 1 e) 3) (IR constant- max. Temp)	-	1000	-
table 1 e) 3) (IR constant- Room temp )	-	1000	-
table 1 e) 3) (Volume Resistivity - Maximum temp)	-	1000	-
table 1 e) 3) (Volume Resistivity - Room temp )	-	1000	-
10.2(HV (room temperature))	-	1000	-
10.1(HV (water immersion))	-	2000	-
10.1(HV (water immersion))	-	2000	-
10.8(Smoke density rating)	-	2000	-
10.6(Halogen evolution)	-	2000	-
10.7(Temperature index)	-	2000	-
10.5(Oxygen index)	-	2000	-
Table 1 iii) d) 9)(Cold impact for sheath)	-	1000	-
Table 1 iii) d) 8)(Cold bend for sheath)	-	1000	-
Table 1 iii) c) 9)(Cold impact for insulation)	-	1000	-
Table 1 iii) c) 8)(Cold bend for insulation)	-	1000	-
Table 1(Category Code)	-	500	-
Table 1 iii) d) 7)(Thermal stability- Sheath )	-	1000	-
Table 1 iii) c) 7)(Thermal stability- Insulation )	-	1000	-
Table 1 iii) d) 6)(Hot deformation -Indentation depth - Sheath )	-	1000	-
Table 1 iii) c) 6)(Hot deformation - Indentation depth- Insulation)	-	1000	-
Table 1 iii) d) 5)(Heat shock-Sheath )	-	1000	-
Table 1 iii) c) 5)(Heat shock-Insulation )	-	1000	-
Table 1 iii) d) 4)(Cracks Observed)	-	1000	-
Table 1 iii) d) 4)(Shrinkage- Sheath )	-	1000	-
Table 1 iii) c) 4)(Cracks Observed)	-	1000	-
Table 1 iii) c) 4)(Shrinkage-Insulation)	-	1000	-
Table 1 iii) d) 2)(Loss of mass- Sheath )	-	2000	-
Table 1 iii) c) 2)(Loss of mass- Insulation )	-	2000	-
Table 1 iii) d) 3)(Sheath- Elongation variation)	-	2000	-
Table 1 iii) d) 3)(Sheath- TS variation)	-	2000	-
Table 1 iii) d) 3)(Sheath- Elongation (After ageing))	-	2000	-
Table 1 iii) d) 3)(Sheath- Tensile strength (After ageing))	-	2000	-
Table 1 iii) d) 1)(Sheath- Elongation (Without ageing))	-	1000	-
Table 1 iii) d) 1)(Sheath -Tensile strength (Without ageing))	-	1000	-
Table 1 iii) c) 3)(Elongation variation)	-	2000	-
Table 1 iii) c) 3)(TS variation)	-	2000	-
Table 1 iii) c) 3)(Elongation (After ageing))	-	2000	-
Table 1 iii) c) 3)(Tensile strength (After ageing))	-	2000	-
Table 1 iii) c) 1)(Elongation (Without ageing))	-	1000	-
Table 1 iii) c) 1)(Tensile strength (Without ageing))	-	1000	-
(Cl. 18.1.4) (Cl. 19.1.5) (Cl. 20.1.4) (Cl. 22.1.4)(Colour of Sheath)	-	500	-
8.3(Thickness of Sheath)	-	500	-
5.2(Application )	-	500	-
5.3(Thickness of Insulation)	-	1000	-
9.1(Ovality)	-	1000	-
9(Overall dimensions)	-	1000	-
10.11(Per sulphate test (for tinned Cu cable only))	-	2000	-
4.2(Conductor resistance test)	-	1000	-
4.1(Wrapping test (for Al))	-	1000	-
4.1(Tensile test (for Al)- After Stranding)	-	1000	-
4.1(Tensile test (for Al)-Before Stranding)	-	1000	-
4.1(Annealing test (for copper))	-	1000	-
(Cl.6.1.3 of IS 8130:2013)(Flexible Conductors (Classes 5))	-	500	-
(Cl.6.1.3 of IS 8130:2013)( Flexible Conductors (Classes 5))	-	500	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors(Class-2))	-	500	-
(Cl.6.1.3 of IS 8130:2013)(Stranded compacted circular conductors and shaped conductors (Class 2))	-	500	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors (Class-2))	-	500	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors (Class-2))	-	500	-
(Cl.6.1.3 of IS 8130:2013)(Solid Conductor (Class 1))	-	500	-
(Cl.6.1 of IS 8130:2013)(Solid Conductor (Class 1))	-	500	-
(Cl.6.1 of IS 8130:2013)(Solid Conductor (Class 1))	-	500	-
(Cl.16.1) (Cl.19.1)(Conductor- Diameter )	-	500	-
(Cl.16.1) (Cl.19.1)(Conductor)	-	500	-
(Cl.16.1) (Cl.19.1)(Conductor)	-	500	-
(Cl.16.1) (Cl.19.1)(Conductor)	-	500	-
(Cl. 18.1.3) (Cl. 19.1.4) (Cl. 20.1.3) (Cl. 21.1.3) (Cl. 22.1.3)(Assembly of cores )	-	500	-
12(CONSTRUCTION Core Identification)	-	500	-
8.1(Sheath Material )	-	500	-
7(Binder Tape)	-	500	-
6.2(Filler)	-	500	-
6.1(Filler)	-	500	-
5.1(Insulation)	-	500	-
4.4(Joints in Conductor)	-	500	-
4.4(Joints in Conductor)	-	500	-
4.1(Conductor - Material)	-	500	-
4.1(Conductor - Material)	-	500	-
10.11(Persulphate Test )	-	2000	-
12.0(Core identification)	-	500	-
4, IS 8130(Construction of conductor)	-	500	-
Table 2, IS 8130(No fo wire in a conductor)	-	500	-
8.3(Minimum thickness of Sheath)	-	1000	-
8.3(Avarage thickness of Sheath)	-	1000	-
5.3(Minimum thickness of insulation)	-	1000	-
5.3(Avarage thickness of insulation)	-	1000	-
Table 4(Copper purity test)	-	5000	-
10.3(Spark test)	-	1000	-
table 1, 4.2(insulation resistance test)	-	2000	-
5.4(Mechanical properties before and after ageing)	-	3000	-
10.3(Spark Test)	-	1000	-
4.1(Material)	-	500	-
4.2(Electrical Resistance)	-	1000	-
5(INSULATION)	-	500	-
6(FILLER)	-	500	-
7(BINDER TAPE)	-	500	-
8(SHEATH)	-	500	-
9(OVERALL DIMENSIONS)	-	1000	-
10.1(High Voltage Test (Water Immersion Test))	-	2000	-
10.2(High Voltage Test (at Room Temperature))	-	1000	-
10.3(Spark Test)	-	1000	-
10.4(Flammability Test)	-	1000	-
10.5(Oxygen Index Test)	-	3000	-
10.6(Test for Halogen Acid Gas Evolution)	-	3000	-
10.7(Test for Temperature Index)	-	3000	-
10.8(Smoke Density Rating)	-	3000	-
10.9(Additional Ageing Test (for Cables for Outdoor Use)	-	4000	-
10.1(Flex Test)	-	2000	-
10.11(Persulphate Test)	-	2000	-
11(IDENTIFICATION)	-	500	-
12(CORE IDENTIFICATION)	-	500	-
13(CABLE CODE)	-	500	-
15(PACKING AND MARKING)	-	500	-
16.1(Construction)	-	500	-
16.2(Tests)	-	500	-
17(SINGLE CORE NON-SHEATHED CABLES WITH FLEXIBLE CONDUCTOR FOR GENERAL PURPOSE (MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C))	-	500	-
18(SINGLE AND MULTICORE CIRCULAR PVC INSULATED AND SHEATHED CABLES WITH RIGID CONDUCTOR (CLASS 1 AND CLASS 2) FOR GENERAL PURPOSE ) FOR MAXIMUM CONDUCTOR TEMPERATURE (70°C OR 85°C))	-	500	-
19(SINGLE AND MULTICORE CIRCULAR PVC INSULATED AND SHEATHED CABLES/CORDS WITH FLEXIBLE CONDUCTOR (CLASS 5) FOR GENERAL PURPOSE (MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C))	-	500	-
20(MULTICORE CIRCULAR PVC INSULATED AND SHEATHED CABLES WITH FLEXIBLE CONDUCTOR (CLASS 5) FOR GENERAL PURPOSE (FOR MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C))	-	500	-
21(ARALLEL TWIN AND TWISTED TWIN FLEXIBLE PVC INSULATED UNSHEATHED CORDS (CLASS 5) FOR GENERAL PURPOSE (FOR MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C))	-	500	-
22(TWO AND THREE CORE FLAT CABLES WITH PVC INSULATION AND SHEATHED (CLASS 2 OR 5) FOR GENERAL PURPOSE( FOR MAXIMUM CONDUCTOR TEMPERA TURE 70°C OR 85°C))	-	500	-
(4.3 of IS 8130:2013)(Form of Conductor)	-	500	-
( 4.4.1 of IS 8130:2013)(Joints in Conductor)	-	500	-
(4.4.2 of IS 8130:2013)(Joints in Conductor Solid Conductors (Aluminium Conductors only))	-	500	-
(Cl.6.1.1 of IS 8130:2013)(Solid Conductor (Class 1))	-	500	-
(Cl.6.1.2 of IS 8130:2013)(Solid Conductor (Class 1))	-	500	-
(Cl.6.1.3 of IS 8130:2013)(Solid Conductor (Class 1))	-	500	-
(6.2.1 of IS 8130:2013)(Stranded Circular Non-compacted Conductors (Class 2))	-	500	-
(6.2.2 of IS 8130:2013)(Stranded Circular Non-compacted Conductors (Class 2))	-	500	-
(6.2.3 of IS 8130:2013)(Stranded Circular Non-compacted Conductors (Class 2))	-	500	-
(6.3.1 of IS 8130:2013)(Stranded Compacted Circular Conductors and Shaped Conductors (Class 2))	-	500	-
(6.3.2 of IS 8130:2013)(Stranded Compacted Circular Conductors and Shaped Conductors (Class 2))	-	500	-
(6.3.3 of IS 8130:2013)(Stranded Compacted Circular Conductors and Shaped Conductors (Class 2))	-	500	-
( 6.4.1 of IS 8130:2013)(Flexible Conductors (Class 5))	-	500	-
(6.4.2 of IS 8130:2013)(Flexible Conductors (Class 5))	-	500	-
( 6.4.3 of IS 8130:2013)(Flexible Conductors (Class 5))	-	500	-
Cl.19.1.4(Assembly of Cores)	-	500	-
Cl. 8.2(Application of Sheath)	-	500	-
5.3(Thickness of Insulation)	-	1000	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors (Class-2))	-	500	-
Table 4(Copper purity test)	-	5000	-
10.3(Spark test)	-	1000	-
table 1, 4.2(insulation resistance test)	-	1000	-
5.4(Mechanical properties before and after ageing)	-	3000	-
10.3(Spark Test)	-	1000	-
4.1(Material)	-	500	-
4.2(Electrical Resistance)	-	1000	-
5(INSULATION)	-	500	-
6(FILLER)	-	500	-
7(BINDER TAPE)	-	500	-
8(SHEATH)	-	500	-
9(OVERALL DIMENSIONS)	-	1000	-
10.1(High Voltage Test (Water Immersion Test))	-	2000	-
10.2(High Voltage Test (at Room Temperature))	-	1000	-
10.3(Spark Test)	-	1000	-
10.4(Flammability Test)	-	1000	-
10.5(Oxygen Index Test)	-	3000	-
10.6(Test for Halogen Acid Gas Evolution)	-	3000	-
10.7(Test for Temperature Index)	-	3000	-
10.8(Smoke Density Rating)	-	2000	-
10.9(Additional Ageing Test (for Cables for Outdoor Use)	-	3000	-
10.1(Flex Test)	-	1000	-
10.11(Persulphate Test)	-	2000	-
11(IDENTIFICATION)	-	500	-
12(CORE IDENTIFICATION)	-	500	-
13(CABLE CODE)	-	500	-
15(PACKING AND MARKING)	-	500	-
16.1(Construction)	-	500	-
16.2(Tests)	-	500	-
17(SINGLE CORE NON-SHEATHED CABLES WITH FLEXIBLE CONDUCTOR FOR GENERAL PURPOSE (MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C))	-	500	-
18(SINGLE AND MULTICORE CIRCULAR PVC INSULATED AND SHEATHED CABLES WITH RIGID CONDUCTOR (CLASS 1 AND CLASS 2) FOR GENERAL PURPOSE ) FOR MAXIMUM CONDUCTOR TEMPERATURE (70°C OR 85°C))	-	500	-
19(SINGLE AND MULTICORE CIRCULAR PVC INSULATED AND SHEATHED CABLES/CORDS WITH FLEXIBLE CONDUCTOR (CLASS 5) FOR GENERAL PURPOSE (MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C))	-	500	-
20(MULTICORE CIRCULAR PVC INSULATED AND SHEATHED CABLES WITH FLEXIBLE CONDUCTOR (CLASS 5) FOR GENERAL PURPOSE (FOR MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C))	-	500	-
21(ARALLEL TWIN AND TWISTED TWIN FLEXIBLE PVC INSULATED UNSHEATHED CORDS (CLASS 5) FOR GENERAL PURPOSE (FOR MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C))	-	500	-
22(TWO AND THREE CORE FLAT CABLES WITH PVC INSULATION AND SHEATHED (CLASS 2 OR 5) FOR GENERAL PURPOSE( FOR MAXIMUM CONDUCTOR TEMPERA TURE 70°C OR 85°C))	-	500	-
(4.3 of IS 8130:2013)(Form of Conductor)	-	500	-
( 4.4.1 of IS 8130:2013)(Joints in Conductor)	-	500	-
(4.4.2 of IS 8130:2013)(Joints in Conductor Solid Conductors (Aluminium Conductors only))	-	500	-
(Cl.6.1.1 of IS 8130:2013)(Solid Conductor (Class 1))	-	500	-
(Cl.6.1.2 of IS 8130:2013)(Solid Conductor (Class 1))	-	500	-
(Cl.6.1.3 of IS 8130:2013)(Solid Conductor (Class 1))	-	500	-
(6.2.1 of IS 8130:2013)(Stranded Circular Non-compacted Conductors (Class 2))	-	500	-
(6.2.2 of IS 8130:2013)(Stranded Circular Non-compacted Conductors (Class 2))	-	500	-
(6.2.3 of IS 8130:2013)(Stranded Circular Non-compacted Conductors (Class 2))	-	500	-
(6.3.1 of IS 8130:2013)(Stranded Compacted Circular Conductors and Shaped Conductors (Class 2))	-	500	-
(6.3.2 of IS 8130:2013)(Stranded Compacted Circular Conductors and Shaped Conductors (Class 2))	-	500	-
(6.3.3 of IS 8130:2013)(Stranded Compacted Circular Conductors and Shaped Conductors (Class 2))	-	500	-
( 6.4.1 of IS 8130:2013)(Flexible Conductors (Class 5))	-	500	-
(6.4.2 of IS 8130:2013)(Flexible Conductors (Class 5))	-	500	-
( 6.4.3 of IS 8130:2013)(Flexible Conductors (Class 5))	-	500	-
Cl.19.1.4(Assembly of Cores)	-	500	-
Cl. 8.2(Application of Sheath)	-	500	-

15 Jun, 2029

-
Included w.e.f.23.06.2025

IS 14927 : Part 2 : Sec 1 (2023)

Cable trunking systems and cable ducting Systems for electrical installations Part 2-1: particular requirements cable trunking systems and cable Ducting systems intended for mounting on walls and ceilings first revision

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.9.1(Sharp edges)	-	500	-
Cl.9.2(Apparatus mounting)	-	500	-
Cl.9.3(Means for protective separation and/or retention)	-	500	-
Cl.9.4(Mechanical connections)	-	2500	-
Cl.9.5(Accessible conductive parts)	-	1500	-
Cl.9.6(Equipotential bonding)	-	1000	-
Cl.9.7(Access to live parts)	-	1000	-
Cl.9.8(Inlet openings)	-	500	-
Cl.9.9(Membranes)	-	500	-
Cl.9.10(Cable restrainer)	-	1000	-
Cl.9.11(Cable anchorage)	-	1000	-
Cl. 9.101(Assembling)	-	500	-
Cl. 9.102(Contact between liquids and insulated conductors and live parts)	-	1500	-
Cl.10.1(Linear deflection test)	-	500	-
Cl.10.1(Mechanical strength)	-	1500	-
Cl.10.2(Cable support test)	-	500	-
Cl.10.3(Impact test)	-	2500	-
Cl.10.5(External load test)	-	2500	-
Cl.10.6(System access cover retention)	-	500	-
Cl. 10.101(Compression test for CDS)	-	1500	-
Cl.11.1(Electrical continuity)	-	500	-
Cl.11.2(Electrical insulation)	-	500	-
Cl.12(Thermal properties)	-	500	-
Cl.13(Fire hazard)	-	500	-
Cl.14(External influences)	-	500	-
Cl. 15(Electromagnetic compatibility)	-	500	-

15 Jun, 2029

-
Included w.e.f.13.05.2025

IS/IEC 60730 : Part 2 : Sec 9 (2011)

Automatic Electrical Controls for Household and Similar Use Part 2 Particular Requirements Section 9 Temperature Sensing Controls

75000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(By inspection)	-	200	-
5.1(By inspection)	-	0	-
5.2(By inspection)	-	0	-
6.1(By inspection)	-	300	-
6.2(By inspection)	-	0	-
6.3(By inspection)	-	0	-
6.4(By inspection)	-	0	-
6.4.3(By inspection)	-	0	-
6.5(By inspection)	-	0	-
6.5.1(IEC 60529 and by inspection)	-	0	-
6.5.2(IEC 60529 and by inspection)	-	500	-
6.5.3(Annexure N and by inspection)	-	500	-
6.6(By inspection)	-	0	-
6.7.1(By inspection)	-	0	-
6.7.2(By inspection)	-	0	-
6.8(By inspection)	-	0	-
6.8.2(By inspection)	-	0	-
6.9(Annexure H and by inspection)	-	500	-
6.1(By inspection)	-	0	-
6.11(By inspection)	-	0	-
6.12(By inspection)	-	0	-
6.13(By inspection)	-	0	-
6.14(By inspection)	-	0	-
6.15(Annexure J and by inspection)	-	0	-
6.16(By inspection)	-	0	-
6.17(Annexure H)	-	200	-
6.18(Annexure H)	-	300	-
8(Test finger as shown in figure 2 with force 20 N/30 N)	-	500	-
9(By inspection)	-	0	-
9.1.1(By inspection)	-	0	-
9.1.2(By inspection)	-	0	-
9.1.3(By inspection)	-	0	-
9.2(By inspection)	-	0	-
9.3.1(1,5 times the rated current and no-load voltage not exceeding 12 V)	-	500	-
9.3.2(by inspection, by manual test and by the appropriate tests of 10. 1)	-	0	-
9.3.4(by inspection, by manual test and by the appropriate tests of 10. 1)	-	0	-
9.3.5(by inspection, by manual test and by the appropriate tests of 10. 1)	-	0	-
9.3.6(by inspection, by manual test and by the appropriate tests of 10. 1)	-	0	-
9.4(by inspection and by plating)	-	200	-
9.4.1(by inspection)	-	0	-
9.4.2(by inspection)	-	0	-
9.5.1(by inspection)	-	0	-
9.5.2(by inspection)	-	0	-
10.1.1(By inspection and as per IEC 60988-2-2)	-	0	-
10.1.1.1(By inspection and as per IEC 60988-2-2)	-	500	-
10.1.2(By inspection )	-	0	-
10.1.3(By inspection )	-	0	-
10.1.4(by inspection, by measurement and by fitting conductors of the smallest and largest cross-sectional areas specified or declared.)	-	0	-
10.1.5(By measurement)	-	300	-
10.1.5.1(by inspection, by measurement, by torque test)	-	0	-
10.1.6(by inspection after cl 10.1.5)	-	0	-
10.1.7(by inspection)	-	0	-
10.1.7.1(by inspection)	-	0	-
10.1.8(The wires of flexible cables and cords are twisted so that there is an even twist of one complete turn in 20 mm.)	-	300	-
10.1.8.4(For flexible cords the test is repeated using a new conductor which is twisted as before, but in the opposite direction)	-	300	-
10.1.9(The pull as shown in table 10.1.9 is applied without jerk for 1 min , In the direction of the axis of the conductor space.)	-	500	-
10.1.11(By inspection)	-	0	-
10.1.12(An 8 mm length of insulation is removed from the end of a stranded conductor having a nominal cross-sectional area equal to the minimum size used during the test of 10.1.4. One wire of the stranded conductor is left free, and the other wires are fully inserted into and clamped in the terminal. The free wire is bent, without tearing the insulation back , in every direction , but without making sharp bends around barriers.)	-	200	-
10.1.13(By inspection and after the test of cl 17)	-	0	-
10.1.14(By inspection)	-	0	-
10.1.15(Figure 11 or 12)	-	300	-
10.2(By inspection)	-	0	-
10.2.1(Table 10.2.1)	-	200	-
10.2.2(By inspection)	-	0	-
10.2.3(By inspection)	-	0	-
10.2.4.1(Figure 14 or 15)	-	300	-
10.2.4.2(During the test of cl 14)	-	0	-
10.2.4.3(As per table 10.2.4.3)	-	0	-
10.2.4.4(As per Figure 16)	-	0	-
11.1(By inspection)	-	0	-
11.1.1(By inspection)	-	0	-
11.1.2(by inspection and by analysis of the material)	-	0	-
11.1.3(by inspection)	-	0	-
11.2(by inspection and by test)	-	0	-
11.2.2(by inspection, by measurement and/or by manual test)	-	0	-
11.2.3(by inspection, by measurement and/or by manual test)	-	0	-
11.2.3.2(by inspection, by measurement and/or by manual test)	-	200	-
11.2.4(as per lEC 60227 or IEC 60245.)	-	300	-
11.2.5(As per annexure H, cl 11.2.5)	-	0	-
11.3.1(by inspection and by the tests of clauses 13 and 20)	-	0	-
11.3.2(by inspection and by the tests of clauses 13)	-	0	-
11.3.3(by inspection)	-	0	-
11.3.4(by inspection)	-	0	-
11.3.5(by inspection)	-	0	-
11.3.6(by inspection, and for a closed position by the temperature requirements of clause 14, and for open position by the requirements of clause 13, as specifiedfor micro -disconnection. )	-	0	-
11.3.7(by inspection, and if necessary as per cl 11.3.7.2)	-	300	-
11.3.8(by inspection)	-	0	-
11.3.9(By pull not exceeding 45 N vertically downwards, or 70 N at 45° to the vertical)	-	200	-
11.4.1 (by inspection)	-	0	-
11.4.2(by inspection)	-	0	-
11.4.3(by the tests of clauses 15 to 17)	-	500	-
11.4.4 to 11.4.16(As per relevent type)	-	0	-
11.5(by inspection)	-	0	-
11.6.1(by inspection and by manual test)	-	0	-
11.6.2(by inspection and by manual test)	-	0	-
11.6.3.1(By inspection)	-	0	-
11.6.3.2(By inspection)	-	0	-
11.6.3.3(By inspection)	-	200	-
11.6.3.4(By inspection)	-	0	-
11.6.3.5(By inspection)	-	0	-
11.6.3.6(By inspection)	-	0	-
11.6.3.7(By inspection)	-	0	-
11.7.1(By Flexing test as per fig 9)	-	300	-
11.7.1.2.2(By Flexing test as per fig 9)	-	500	-
11.7.1.2.3(By Flexing test as per fig 9)	-	0	-
11.7.2.1 to 11.7.2.10(torque equal to two-thirds of the torque specified in 19.1)	-	500	-
11.7.2.11 to 11.7.2.15(By pull test as per table 11.7.2)	-	0	-
11.7.2.11 to 11.7.2.15(By measurement)	-	0	-
11.8(By inspection)	-	0	-
11.8.1(By inspection)	-	0	-
11.8.2(By inspection and as per table 11.8.2)	-	500	-
11.8.3(by inspection and by connecting cords of the largest cross-sectional eree used in 10.1.4)	-	500	-
11.9.1(By inspection)	-	0	-
11.9.1.1(by inspection and manual test)	-	0	-
11.9.1.2(by inspection and manual test)	-	0	-
11.9.1.3(by inspection and manual test)	-	0	-
11.9.1.4(by inspection and manual test)	-	0	-
11.10.1(by inspection)	-	0	-
11.10.2(by inspection)	-	0	-
11.10.3(by inspection and by test of socket-outlet system)	-	0	-
11.11(Requirements during mounting, maintenance and servicing)	-	1000	-
11.11.1(By inspection)	-	0	-
11.11.1.1(By inspection)	-	0	-
11.11.1.5(As per cl 11.11.1.5.1 to 11.11.1.5.3)	-	500	-
11.11.1.5.4(By inspection)	-	0	-
11.11.1.5.6(by pull test)	-	500	-
11.11.2(By inspection)	-	0	-
11.11.3.1(by inspection and, for actuating members which do not requ ire a tool for their removal, by the test of 18.9)	-	500	-
11.11.3.2(by inspection and, for actuating members which do not requ ire a tool for their removal, by the test of 18.9)	-	500	-
11.11.3.3(by inspection and, for actuating members which do not requ ire a tool for their removal, by the test of 18.9)	-	500	-
11.11.4(By inspection)	-	0	-
11.11.5(By inspection and by manual test)	-	0	-
11.11.6(By inspection)	-	0	-
11.11.7(By inspection)	-	0	-
11.12(As per H, cl 11.12)	-	500	-
12.1(As per IEC 60529)	-	500	-
12.1.6.2(Torque test)	-	500	-
11.11.1.2(By inspection)	-	0	-
12.2(Humidity treatment at 91 % and 95 % and temp between 20 to 30°C)	-	500	-
13.1(as per table 13.1)	-	500	-
13.2(As per table 13.2)	-	500	-
12.3(as per cl 12.3.1 to 12.3.7)	-	500	-
13.3.1 to 13.3.4(as per clause 13.3.4)	-	500	-
14.1(As per table 14.1)	-	500	-
14.3(As per table 14.1)	-	500	-
15(as per cl 15.1 to 15.4)	-	500	-
15.5(as per cl 15.5 to 15.6)	-	500	-
15.6.4(42 of table 7.2, and as per annexure AA)	-	500	-
15.7(as per annexure J, cl 15.7)	-	500	-
16.2(as per cl 16.2.1 to 16.2.3 )	-	500	-
16.2.4(test of cl 15 repeated )	-	500	-
16.2.4(42 of table 7.2)	-	500	-
17.1(by the tests of 17.1.3 as indicated in 17.16)	-	500	-
17.6(as per cl 17.6.1 and 17.6.2)	-	500	-
17.7(as per cl 17.7.1 to 17.7.7)	-	500	-
17.8(as per cl 17.8.1 to 17.8.4.1)	-	500	-
17.9(as per cl 17.9.1 to 17.9.4)	-	500	-
17.1(as per cl 17.10.1 to 17.10.4)	-	500	-
17.11(as per cl 17.11.1 to 17.11.4)	-	500	-
17.12(as per cl 17.12.1 to 17.12.5)	-	500	-
17.13(as per cl 17.13.1 to 17.13.4)	-	500	-
H 17.1.4.2(as per cl H 17.1.4.2)	-	500	-
H.17.14(as per cl H 17.4.16)	-	500	-
17.15.2(as per cl 17.15.2 and 17.15.2.3)	-	500	-
J 17.18.5(as per cl J 17.8.5)	-	500	-
J 17.18.5(as per cl J 17.8.6)	-	500	-
J 17.17.2(as per table 13.1)	-	500	-
J 17.17(As per table 13.2)	-	500	-
J. 17. 18.2(as per cl J. 17. 18.2)	-	500	-
J. 17. 18.3(as per cl J. 17. 18.3)	-	500	-
J. 17. 18.4(as per cl J. 17. 18.4)	-	500	-
18.1.6(By inspection)	-	500	-
18.1.6.1(By inspection)	-	0	-
18.1.6.2(By inspection)	-	0	-
18.1.6.3(Pull test as per cl 18.1.6.3)	-	500	-
18.2(Impact tester)	-	500	-
18.5(by the test of 18.5.2 and 18.5.3using the apparatus shown in figure 4)	-	500	-
18.6(tested in a tumbling barrel as per cl 18.6.2 to 18.6.5)	-	500	-
18.7(Pull test as per table 18.7)	-	500	-
18.8(as per cl 18.8.2 and 18.8.3)	-	500	-
18.9(axial pull of 15N/30N)	-	500	-
19.1.1(by inspection and by the test of 19. 1. 11 to 19. 1.15)	-	0	-
19.1.2(by inspection and by the test of 19. 1. 11 to 19. 1.15)	-	0	-
19.1.3(by inspection and by the test of 19. 1. 11 to 19. 1.15)	-	0	-
19.1.4(by inspection and by the test of 19. 1. 11 to 19. 1.15)	-	0	-
19.1.5(by inspection and by the test of 19. 1. 11 to 19. 1.15)	-	0	-
19.1.6(by inspection and by the test of 19. 1. 11 to 19. 1.15)	-	0	-
19.1.8(by inspection and by the test of 19. 1. 11 to 19. 1.15)	-	0	-
19.1.9(by inspection and by the test of 19. 1. 11 to 19. 1.15)	-	0	-
19.2.1(By inspection)	-	0	-
19.2.2(By inspection)	-	0	-
19.2.3(By inspection)	-	0	-
19.2.4(By inspection)	-	0	-
19.2.4.1(By inspection)	-	0	-
19.2.5(By inspection)	-	0	-
19.2.5.1(By inspection)	-	0	-
19.2.6(By inspection)	-	0	-
20.1(as per table 20.2)	-	500	-
20.2.1(as per table 20.3)	-	500	-
20.2.2(as per table 20.4)	-	500	-
21.2.2 to 21.2.6(Ball pressure test as per cl 21.2.5)	-	500	-
21.2.2 to 21.2.6(as per annexure G)	-	500	-
21.2.7(As per cl G.4)	-	500	-
22.1.1(As per cl 21.1.3 to 21.1.6)	-	500	-
24.1(as per IEC 60742)	-	500	-
24.1(as per IEC 60384-14)	-	500	-
24.1(as per IEC 60127 or IEC 60269)	-	500	-
25(as per annexure H)	-	500	-
27.1(as per annexure H)	-	500	-
27.2(as per cl 27.2.1 and 27.2.2)	-	500	-
27.3( 85 % of the minimum rated voltage and 110 % of the maximum rated voltage inclusive .)	-	500	-
H 27.4(as per cl H 27.4.1 and H 27.4.2)	-	500	-
11.1.101(Additional test as per IS 60730 : Part 2 : Sec 9 : 2011 ( Other than test covered in Part 1) by inspection of the manufacturer's declaration and by the test of 18.102. )	-	500	-
11.1.102(As per IEC 60216-1:2001)	-	500	-
11.4.13.102(an impact tool is dropped once from a height of 0.60 m )	-	500	-
11.4.101(as per cl 11.4.101)	-	500	-
11.4.103(table 7.2 item 103 and by the test of cl 17.15)	-	500	-
11.4.107(As per annexure DD)	-	500	-
11.6.3.101(As per table 7, item 117)	-	500	-
11.101(As per annexure BB)	-	500	-
12.101(None)	-	500	-
12.101.2(15 K+Tmax for 16 hr)	-	500	-
12.101.5(as per 12.103 to 12.105)	-	500	-
12.101.6(a voltage equal to (2 x VR) + 1 000 V is applied at rated frequency for 1 min )	-	500	-
14.101.1( as per cl 14.102 and 14.102.1)	-	500	-
15.5.3.101 to 15.5.3.105(According to type of control)	-	500	-
15.5.3.109( voltage specified in Table 13.2)	-	500	-
17.16.106(as per cl 17.7 and 17.8 at an ambient temperature of (20 ± 5) °C)	-	500	-
17.16.107( 250 thermal cycles.)	-	500	-
17.16.108( 7 h at a temperature of –20 C (or lower, if declared))	-	500	-
17.101.1(as per cl 17.101.1 to 17.105)	-	500	-
18.101(as per cl 18.101.2 and 101.3)	-	500	-
18.102(Hydrualic test)	-	500	-
5(Rating)	-	500	-
6(Classification)	-	500	-
7(Information)	-	500	-
8(Protection against Electric Shock)	-	500	-
9(Provision for Protective Earthing)	-	500	-
10(Terminals and terminations)	-	500	-
11(Constructional Requirements)	-	500	-
12(Moisture and Dust Resistance)	-	2500	-
13(Electric Strength and Insulation Resistance)	-	500	-
14(Heating)	-	500	-
15(Manufacturing Deviation and Drift)	-	500	-
16(Environmental Stress)	-	500	-
17(Endurance)	-	4400	-
18(Mechanical Strength)	-	500	-
19(Threaded Parts and Connections)	-	500	-
20(Creepage Distances, Clearancces and distance through solid insulation)	-	500	-
21(Fire Hazard Testing)	-	500	-
22(Resistance to Corrosion)	-	500	-
25(Normal Operation)	-	500	-
24(Components)	-	500	-
27(Abnormal Operation)	-	500	-
28(Guidance on the use of Electronic Disconnection)	-	500	-
5(By inspection)	-	500	-
5.1(By inspection)	-	0	-
5.2(By inspection)	-	0	-
6.1(By inspection)	-	500	-
6.2(By inspection)	-	0	-
6.3(By inspection)	-	0	-
6.4(By inspection)	-	0	-
6.4.3(By inspection)	-	0	-
6.5(By inspection)	-	0	-
6.5.1(IEC 60529 and by inspection)	-	0	-
6.5.2(IEC 60529 and by inspection)	-	0	-
6.5.3(Annexure N and by inspection)	-	0	-
6.6(By inspection)	-	0	-
6.7.1(By inspection)	-	0	-
6.7.2(By inspection)	-	0	-
6.8(By inspection)	-	0	-
6.8.2(By inspection)	-	0	-
6.9(Annexure H and by inspection)	-	500	-
6.1(By inspection)	-	0	-
6.11(By inspection)	-	0	-
6.12(By inspection)	-	0	-
6.13(By inspection)	-	0	-
6.14(By inspection)	-	0	-
6.15(Annexure J and by inspection)	-	0	-
6.16(By inspection)	-	0	-
6.17(Annexure H)	-	0	-
6.18(Annexure H)	-	0	-
8(Test finger as shown in figure 2 with force 20 N/30 N)	-	500	-
9(By inspection)	-	0	-
9.1.1(By inspection)	-	0	-
9.1.2(By inspection)	-	0	-
9.1.3(By inspection)	-	0	-
9.2(By inspection)	-	0	-
9.3.1(1,5 times the rated current and no-load voltage not exceeding 12 V)	-	0	-
9.3.2(by inspection, by manual test and by the appropriate tests of 10. 1)	-	0	-
9.3.4(by inspection, by manual test and by the appropriate tests of 10. 1)	-	0	-
9.3.5(by inspection, by manual test and by the appropriate tests of 10. 1)	-	0	-
9.3.6(by inspection, by manual test and by the appropriate tests of 10. 1)	-	0	-
9.4(by inspection and by plating)	-	0	-
9.4.1(by inspection)	-	0	-
9.4.2(by inspection)	-	0	-
9.5.1(by inspection)	-	0	-
9.5.2(by inspection)	-	0	-
10.1.1(By inspection and as per IEC 60988-2-2)	-	0	-
10.1.1.1(By inspection and as per IEC 60988-2-2)	-	0	-
10.1.2(By inspection )	-	0	-
10.1.3(By inspection )	-	0	-
10.1.4(by inspection, by measurement and by fitting conductors of the smallest and largest cross-sectional areas specified or declared.)	-	0	-
10.1.5(By measurement)	-	0	-
10.1.5.1(by inspection, by measurement, by torque test)	-	0	-
10.1.6(by inspection after cl 10.1.5)	-	0	-
10.1.7(by inspection)	-	0	-
10.1.7.1(by inspection)	-	0	-
10.1.8(The wires of flexible cables and cords are twisted so that there is an even twist of one complete turn in 20 mm.)	-	0	-
10.1.8.4(For flexible cords the test is repeated using a new conductor which is twisted as before, but in the opposite direction)	-	0	-
10.1.9(The pull as shown in table 10.1.9 is applied without jerk for 1 min , In the direction of the axis of the conductor space.)	-	0	-
10.1.11(By inspection)	-	0	-
10.1.12(An 8 mm length of insulation is removed from the end of a stranded conductor having a nominal cross-sectional area equal to the minimum size used during the test of 10.1.4. One wire of the stranded conductor is left free, and the other wires are fully inserted into and clamped in the terminal. The free wire is bent, without tearing the insulation back , in every direction , but without making sharp bends around barriers.)	-	0	-
10.1.13(By inspection and after the test of cl 17)	-	0	-
10.1.14(By inspection)	-	0	-
10.1.15(Figure 11 or 12)	-	0	-
10.2(By inspection)	-	0	-
10.2.1(Table 10.2.1)	-	0	-
10.2.2(By inspection)	-	0	-
10.2.3(By inspection)	-	0	-
10.2.4.1(Figure 14 or 15)	-	0	-
10.2.4.2(During the test of cl 14)	-	0	-
10.2.4.3(As per table 10.2.4.3)	-	0	-
10.2.4.4(As per Figure 16)	-	0	-
11.1(By inspection)	-	0	-
11.1.1(By inspection)	-	0	-
11.1.2(by inspection and by analysis of the material)	-	0	-
11.1.3(by inspection)	-	0	-
11.2(by inspection and by test)	-	0	-
11.2.2(by inspection, by measurement and/or by manual test)	-	200	-
11.2.3(by inspection, by measurement and/or by manual test)	-	0	-
11.2.3.2(by inspection, by measurement and/or by manual test)	-	0	-
11.2.4(as per lEC 60227 or IEC 60245.)	-	500	-
11.2.5(As per annexure H, cl 11.2.5)	-	0	-
11.3.1(by inspection and by the tests of clauses 13 and 20)	-	0	-
11.3.2(by inspection and by the tests of clauses 13)	-	0	-
11.3.3(by inspection)	-	0	-
11.3.4(by inspection)	-	0	-
11.3.5(by inspection)	-	0	-
11.3.6(by inspection, and for a closed position by the temperature requirements of clause 14, and for open position by the requirements of clause 13, as specifiedfor micro -disconnection. )	-	0	-
11.3.7(by inspection, and if necessary as per cl 11.3.7.2)	-	200	-
11.3.8(by inspection)	-	500	-
11.3.9(By pull not exceeding 45 N vertically downwards, or 70 N at 45° to the vertical)	-	0	-
11.4.1 (by inspection)	-	0	-
11.4.2(by inspection)	-	0	-
11.4.3(by the tests of clauses 15 to 17)	-	0	-
11.4.4 to 11.4.16(As per relevent type)	-	0	-
11.5(by inspection)	-	0	-
11.6.1(by inspection and by manual test)	-	0	-
11.6.2(by inspection and by manual test)	-	0	-
11.6.3.1(By inspection)	-	0	-
11.6.3.2(By inspection)	-	0	-
11.6.3.3(By inspection)	-	0	-
11.6.3.4(By inspection)	-	0	-
11.6.3.5(By inspection)	-	0	-
11.6.3.6(By inspection)	-	0	-
11.6.3.7(By inspection)	-	0	-
11.7.1(By Flexing test as per fig 9)	-	0	-
11.7.1.2.2(By Flexing test as per fig 9)	-	0	-
11.7.1.2.3(By Flexing test as per fig 9)	-	0	-
11.7.2.1 to 11.7.2.10(torque equal to two-thirds of the torque specified in 19.1)	-	500	-
11.7.2.11 to 11.7.2.15(By pull test as per table 11.7.2)	-	0	-
11.7.2.11 to 11.7.2.15(By measurement)	-	0	-
11.8(By inspection)	-	0	-
11.8.1(By inspection)	-	0	-
11.8.2(By inspection and as per table 11.8.2)	-	0	-
11.8.3(by inspection and by connecting cords of the largest cross-sectional eree used in 10.1.4)	-	0	-
11.9.1(By inspection)	-	0	-
11.9.1.1(by inspection and manual test)	-	0	-
11.9.1.2(by inspection and manual test)	-	0	-
11.9.1.3(by inspection and manual test)	-	0	-
11.9.1.4(by inspection and manual test)	-	0	-
11.10.1(by inspection)	-	0	-
11.10.2(by inspection)	-	0	-
11.10.3(by inspection and by test of socket-outlet system)	-	0	-
11.11(Requirements during mounting, maintenance and servicing)	-	0	-
11.11.1(By inspection)	-	0	-
11.11.1.1(By inspection)	-	0	-
11.11.1.5(As per cl 11.11.1.5.1 to 11.11.1.5.3)	-	0	-
11.11.1.5.4(By inspection)	-	0	-
11.11.1.5.6(by pull test)	-	0	-
11.11.2(By inspection)	-	0	-
11.11.3.1(by inspection and, for actuating members which do not requ ire a tool for their removal, by the test of 18.9)	-	0	-
11.11.3.2(by inspection and, for actuating members which do not requ ire a tool for their removal, by the test of 18.9)	-	0	-
11.11.3.3(by inspection and, for actuating members which do not requ ire a tool for their removal, by the test of 18.9)	-	0	-
11.11.4(By inspection)	-	0	-
11.11.5(By inspection and by manual test)	-	0	-
11.11.6(By inspection)	-	0	-
11.11.7(By inspection)	-	0	-
11.12(As per H, cl 11.12)	-	0	-
12.1(As per IEC 60529)	-	0	-
12.1.6.2(Torque test)	-	0	-
11.11.1.2(By inspection)	-	0	-
12.2(Humidity treatment at 91 % and 95 % and temp between 20 to 30°C)	-	0	-
13.1(as per table 13.1)	-	500	-
13.2(As per table 13.2)	-	0	-
12.3(as per cl 12.3.1 to 12.3.7)	-	0	-
13.3.1 to 13.3.4(as per clause 13.3.4)	-	0	-
14.1(As per table 14.1)	-	0	-
14.3(As per table 14.1)	-	500	-
15(as per cl 15.1 to 15.4)	-	0	-
15.5(as per cl 15.5 to 15.6)	-	0	-
15.6.4(42 of table 7.2, and as per annexure AA)	-	0	-
15.7(as per annexure J, cl 15.7)	-	0	-
16.2(as per cl 16.2.1 to 16.2.3 )	-	0	-
16.2.4(test of cl 15 repeated )	-	0	-
16.2.4(42 of table 7.2)	-	500	-
17.1(by the tests of 17.1.3 as indicated in 17.16)	-	500	-
17.6(as per cl 17.6.1 and 17.6.2)	-	500	-
17.7(as per cl 17.7.1 to 17.7.7)	-	500	-
17.8(as per cl 17.8.1 to 17.8.4.1)	-	0	-
17.9(as per cl 17.9.1 to 17.9.4)	-	0	-
17.1(as per cl 17.10.1 to 17.10.4)	-	0	-
17.11(as per cl 17.11.1 to 17.11.4)	-	0	-
17.12(as per cl 17.12.1 to 17.12.5)	-	500	-
17.13(as per cl 17.13.1 to 17.13.4)	-	500	-
H 17.1.4.2(as per cl H 17.1.4.2)	-	500	-
H.17.14(as per cl H 17.4.16)	-	0	-
17.15.2(as per cl 17.15.2 and 17.15.2.3)	-	0	-
J 17.18.5(as per cl J 17.8.5)	-	0	-
J 17.18.5(as per cl J 17.8.6)	-	500	-
J 17.17.2(as per table 13.1)	-	0	-
J 17.17(As per table 13.2)	-	0	-
J. 17. 18.2(as per cl J. 17. 18.2)	-	0	-
J. 17. 18.3(as per cl J. 17. 18.3)	-	0	-
J. 17. 18.4(as per cl J. 17. 18.4)	-	0	-
18.1.6(By inspection)	-	500	-
18.1.6.1(By inspection)	-	500	-
18.1.6.2(By inspection)	-	0	-
18.1.6.3(Pull test as per cl 18.1.6.3)	-	0	-
18.2(Impact tester)	-	0	-
18.5(by the test of 18.5.2 and 18.5.3using the apparatus shown in figure 4)	-	1000	-
18.6(tested in a tumbling barrel as per cl 18.6.2 to 18.6.5)	-	0	-
18.7(Pull test as per table 18.7)	-	0	-
18.8(as per cl 18.8.2 and 18.8.3)	-	500	-
18.9(axial pull of 15N/30N)	-	500	-
19.1.1(by inspection and by the test of 19. 1. 11 to 19. 1.15)	-	1000	-
19.1.2(by inspection and by the test of 19. 1. 11 to 19. 1.15)	-	0	-
19.1.3(by inspection and by the test of 19. 1. 11 to 19. 1.15)	-	0	-
19.1.4(by inspection and by the test of 19. 1. 11 to 19. 1.15)	-	0	-
19.1.5(by inspection and by the test of 19. 1. 11 to 19. 1.15)	-	0	-
19.1.6(by inspection and by the test of 19. 1. 11 to 19. 1.15)	-	0	-
19.1.8(by inspection and by the test of 19. 1. 11 to 19. 1.15)	-	0	-
19.1.9(by inspection and by the test of 19. 1. 11 to 19. 1.15)	-	0	-
19.2.1(By inspection)	-	0	-
19.2.2(By inspection)	-	0	-
19.2.3(By inspection)	-	0	-
19.2.4(By inspection)	-	0	-
19.2.4.1(By inspection)	-	0	-
19.2.5(By inspection)	-	0	-
19.2.5.1(By inspection)	-	500	-
19.2.6(By inspection)	-	500	-
20.1(as per table 20.2)	-	0	-
20.2.1(as per table 20.3)	-	0	-
20.2.2(as per table 20.4)	-	0	-
21.2.2 to 21.2.6(Ball pressure test as per cl 21.2.5)	-	500	-
21.2.2 to 21.2.6(as per annexure G)	-	500	-
21.2.7(As per cl G.4)	-	0	-
22.1.1(As per cl 21.1.3 to 21.1.6)	-	0	-
24.1(as per IEC 60742)	-	0	-
24.1(as per IEC 60384-14)	-	0	-
24.1(as per IEC 60127 or IEC 60269)	-	500	-
25(as per annexure H)	-	0	-
27.1(as per annexure H)	-	0	-
27.2(as per cl 27.2.1 and 27.2.2)	-	0	-
27.3( 85 % of the minimum rated voltage and 110 % of the maximum rated voltage inclusive .)	-	0	-
H 27.4(as per cl H 27.4.1 and H 27.4.2)	-	0	-
11.1.101(Additional test as per IS 60730 : Part 2 : Sec 9 : 2011 ( Other than test covered in Part 1) by inspection of the manufacturer's declaration and by the test of 18.102. )	-	500	-
11.1.102(As per IEC 60216-1:2001)	-	0	-
11.4.13.102(an impact tool is dropped once from a height of 0.60 m )	-	0	-
11.4.101(as per cl 11.4.101)	-	0	-
11.4.103(table 7.2 item 103 and by the test of cl 17.15)	-	0	-
11.4.107(As per annexure DD)	-	500	-
11.6.3.101(As per table 7, item 117)	-	500	-
11.101(As per annexure BB)	-	500	-
12.101(None)	-	500	-
12.101.2(15 K+Tmax for 16 hr)	-	0	-
12.101.5(as per 12.103 to 12.105)	-	0	-
12.101.6(a voltage equal to (2 x VR) + 1 000 V is applied at rated frequency for 1 min )	-	0	-
14.101.1( as per cl 14.102 and 14.102.1)	-	500	-
15.5.3.101 to 15.5.3.105(According to type of control)	-	500	-
15.5.3.109( voltage specified in Table 13.2)	-	0	-
17.16.106(as per cl 17.7 and 17.8 at an ambient temperature of (20 ± 5) °C)	-	0	-
17.16.107( 250 thermal cycles.)	-	0	-
17.16.108( 7 h at a temperature of –20 C (or lower, if declared))	-	0	-
17.101.1(as per cl 17.101.1 to 17.105)	-	0	-
18.101(as per cl 18.101.2 and 101.3)	-	0	-
18.102(Hydrualic test)	-	0	-
5(Rating)	-	0	-
6(Classification)	-	0	-
7(Information)	-	500	-
8(Protection against Electric Shock)	-	500	-
9(Provision for Protective Earthing)	-	500	-
10(Terminals and terminations)	-	2000	-
11(Constructional Requirements)	-	2000	-
12(Moisture and Dust Resistance)	-	1000	-
13(Electric Strength and Insulation Resistance)	-	1000	-
14(Heating)	-	1000	-
15(Manufacturing Deviation and Drift)	-	1000	-
16(Environmental Stress)	-	1000	-
17(Endurance)	-	5000	-
18(Mechanical Strength)	-	1000	-
19(Threaded Parts and Connections)	-	1000	-
20(Creepage Distances, Clearancces and distance through solid insulation)	-	1000	-
21(Fire Hazard Testing)	-	1000	-
22(Resistance to Corrosion)	-	1000	-
25(Normal Operation)	-	1000	-
24(Components)	-	1000	-
27(Abnormal Operation)	-	500	-
28(Guidance on the use of Electronic Disconnection)	-	2000	-

15 Jun, 2029

-
Included w.e.f.16.07.2025

IS 398 : Part 1 (1996)

Aluminium conductors for overhead transmission purposes - Specification: Part 1 aluminium stranded conductors (Third Revision)

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
12.2, Table-1(Measurement of diameter of individual aluminium wire)	-	500	-
12.3, Table-1(Breaking load before stranding)	-	500	-
12.3, Table-1(Breaking load after stranding)	-	1000	-
12.4(Wrapping test)	-	500	-
12.5, Table 1(Resistance test)	-	1000	-
12.6, Table 3(Measurement of lay ratio)	-	500	-
9.3(Stranding)	-	500	-
6(Freedom from defects)	-	500	-
7.2.1(Sizes)	-	500	-
8, 8.1, 8.2(Joint in wires, except during stranding)	-	500	-
9.2(Lay ratio)	-	500	-
9.4(Multiple layer of wires)	-	500	-
4.1(Resistivity)	-	500	-
4.2(Density)	-	500	-
4.3(Constant-Mass Temperature Coefficient of Resistance)	-	1000	-
4.4(Coefficient of Linear Expansion)	-	1000	-
5(Material)	-	500	-
7.1.1(Nominal Sizes)	-	500	-
7.2.2(Resistance)	-	1000	-
12.2, Table-1(Measurement of diameter of individual aluminium wire)	-	500	-
12.3, Table-1(Breaking load before stranding)	-	500	-
12.3, Table-1(Breaking load after stranding)	-	500	-
12.4(Wrapping test)	-	500	-
12.5, Table 1(Resistance test)	-	500	-
12.6, Table 3(Measurement of lay ratio)	-	500	-
9.3(Stranding)	-	500	-
6(Freedom from defects)	-	500	-
7.2.1(Sizes)	-	500	-
8, 8.1, 8.2(Joint in wires, except during stranding)	-	500	-
9.2(Lay ratio)	-	500	-
9.4(Multiple layer of wires)	-	500	-
4.1(Resistivity)	-	500	-
4.2(Density)	-	500	-
4.3(Constant-Mass Temperature Coefficient of Resistance)	-	1000	-
4.4(Coefficient of Linear Expansion)	-	1000	-
5(Material)	-	500	-
7.1.1(Nominal Sizes)	-	500	-
7.2.2(Resistance)	-	1000	-
12.2, Table-1(Measurement of diameter of individual aluminium wire)	-	500	-
12.3, Table-1(Breaking load before stranding)	-	500	-
12.3, Table-1(Breaking load after stranding)	-	1000	-
12.4(Wrapping test)	-	500	-
12.5, Table 1(Resistance test)	-	1000	-
12.6, Table 3(Measurement of lay ratio)	-	500	-
9.3(Stranding)	-	500	-
6(Freedom from defects)	-	500	-
7.2.1(Sizes)	-	500	-
8, 8.1, 8.2(Joint in wires, except during stranding)	-	500	-
9.2(Lay ratio)	-	500	-
9.4(Multiple layer of wires)	-	500	-
4.1(Resistivity)	-	500	-
4.2(Density)	-	500	-
4.3(Constant-Mass Temperature Coefficient of Resistance)	-	1000	-
4.4(Coefficient of Linear Expansion)	-	1000	-
5(Material)	-	500	-
7.1.1(Nominal Sizes)	-	500	-
7.2.2(Resistance)	-	1000	-

15 Jun, 2029

-
Included w.e.f.13.05.2025

IS 14255 (1995)

Aertal bunched cables - For working voltages up to and including 1100 Volts - Specification

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Phase/Street Lighting conductor)	-	1000	-
4.2(Messenger (Neutral Conductor or Otherwise))	-	500	-
5.1(Insulation)	-	500	-
6.1(Flexibility class)	-	500	-
6.2(Compactness)	-	500	-
6.2(No of strands)	-	500	-
6.2(Surface)	-	500	-
6.3(Protective barrier)	-	500	-
6.4(size of street lighting conductor)	-	500	-
6.5(Size of messenger conductor )	-	500	-
6.6(Joints in messenger conductor )	-	500	-
6.6(Direction of outer layer)	-	500	-
7.1(Insulation)	-	500	-
7.2( Thickness of insulation)	-	500	-
7.3(Tolerance on thickness of insulation )	-	500	-
7.4(Aplication of the insulation )	-	500	-
7.5(Colour of the insulation )	-	500	-
8.1(Core identification)	-	100	10
8.2(Core identification)	-	100	-
8.3(Identification by other means)	-	100	-
9.1(Assembly (Laying up))	-	100	-
9.2(Assembly (Laying up))	-	100	-
9.3(Direction of lay)	-	100	-
10.1 a) i)(Tests on phase/street light conductor: tensile test - Test method IS10810:Part 2)	-	500	-
10.1 a) ii)(Wrapping test - 10810: Part 3)	-	500	-
10.1 a) iii)(Resistance test - IS10810: Part 5)	-	500	-
10.1 b) i)(Test on messenger conductor: Breaking load - IS 10810: Part 2)	-	500	-
10.1 b) ii)(Test on messenger conductor: Elongation test - Cl 11.3)	-	500	-
10.1 b) iii)(Test on messenger conductor: Resistance test - IS 10810: Part 5)	-	500	-
10.1 c) i)(Physical tests for XLPE Insulation: Tensile strength - IS 10810: Part 7)	-	500	-
10.1 c) i)(Physical tests for XLPE Insulation: elongation at break - IS 10810: part 7)	-	500	-
10.1 c) ii)(Ageing in air oven : Tensile strength variation - IS 10810:Part 11)	-	500	-
10.1 c) ii)(Ageing in air oven : Elongation variation- IS 10810: Part 11)	-	500	-
10.1 c) iii)(Hot set test: Elongation under load - IS 10810: Part 30)	-	500	-
10.1 c) iii)(Hot set test: Permanent elongation (set) after cooling - IS 10810: Part 30)	-	500	-
10.1 c) iv)(Shrinkage test : Shrinkage - 10810:Part 12)	-	500	-
10.1 c) iv)(Shrinkage test : Crack Observed - 10810:Part 12)	-	500	-
10.1 c) v)(Water ahsorption (Gravimetric) - IS 10810: Part 33 )	-	500	-
10.1 d) i)(Physical test for PE insulation: Tensile strength - IS 10810: Part 7 )	-	500	-
10.1 d) i)(Physical test for PE insulation: elongation at break - IS 10810: Part 7)	-	500	-
10.1 d) ii)(Melt flow index- IS 10810: Part 23)	-	500	-
10.1 d) iv)(Vicat softening point -IS 10810: Part 22)	-	500	-
10.1 d) v)(Environmental stress cracking -IS 10810:Part29)	-	500	-
10.1 f)(Insulation resistance (Volume resistivity) test a) volume resistivity at 27°C - IS 10810: Part 43)	-	500	-
10.1 f)(Insulation resistance (Volume resistivity) test b) volume resistivity at 70°C - IS 10810: Part 43)	-	500	-
10.1 g)(High voltage test - IS10810:Part 45)	-	500	-
11.4(Bending Test on the Completed Cable ( Optional) )	-	500	-
11.4(Bending Test on the Completed Cable ( Optional))	-	500	-
10.1 d) iii)(Carbon Black Content)	-	500	-
6.1(Construction of phase conductor)	-	500	-
6.1(Number of wires (phase conductor))	-	500	-
6.1(Construction of Street Lighting conductor)	-	500	-
6.1(Number of wires (Street Lighting conductor))	-	500	-
12.1(Manufacturer's Identification)	-	500	-
12.2(Cable Identification)	-	500	-
4.1(Phase/Street Lighting conductor)	-	500	-
4.2(Messenger (Neutral Conductor or Otherwise))	-	500	-
5.1(Insulation)	-	500	-
6.1(Flexibility class)	-	500	-
6.2(Compactness)	-	500	-
6.2(No of strands)	-	500	-
6.2(Surface)	-	500	-
6.3(Protective barrier)	-	500	-
6.4(size of street lighting conductor)	-	500	-
6.5(Size of messenger conductor )	-	500	-
6.6(Joints in messenger conductor )	-	500	-
6.6(Direction of outer layer)	-	500	-
7.1(Insulation)	-	500	-
7.2( Thickness of insulation)	-	500	-
7.3(Tolerance on thickness of insulation )	-	500	-
7.4(Aplication of the insulation )	-	500	-
7.5(Colour of the insulation )	-	500	-
8.1(Core identification)	-	500	-
8.2(Core identification)	-	500	-
8.3(Identification by other means)	-	500	-
9.1(Assembly (Laying up))	-	500	-
9.2(Assembly (Laying up))	-	500	-
9.3(Direction of lay)	-	500	-
10.1 a) i)(Tests on phase/street light conductor: tensile test - Test method IS10810:Part 2)	-	500	-
10.1 a) ii)(Wrapping test - 10810: Part 3)	-	500	-
10.1 a) iii)(Resistance test - IS10810: Part 5)	-	500	-
10.1 b) i)(Test on messenger conductor: Breaking load - IS 10810: Part 2)	-	500	-
10.1 b) ii)(Test on messenger conductor: Elongation test - Cl 11.3)	-	500	-
10.1 b) iii)(Test on messenger conductor: Resistance test - IS 10810: Part 5)	-	500	-
10.1 c) i)(Physical tests for XLPE Insulation: Tensile strength - IS 10810: Part 7)	-	500	-
10.1 c) i)(Physical tests for XLPE Insulation: elongation at break - IS 10810: part 7)	-	500	-
10.1 c) ii)(Ageing in air oven : Tensile strength variation - IS 10810:Part 11)	-	2000	-
10.1 c) ii)(Ageing in air oven : Elongation variation- IS 10810: Part 11)	-	2000	-
10.1 c) iii)(Hot set test: Elongation under load - IS 10810: Part 30)	-	1000	-
10.1 c) iii)(Hot set test: Permanent elongation (set) after cooling - IS 10810: Part 30)	-	1000	-
10.1 c) iv)(Shrinkage test : Shrinkage - 10810:Part 12)	-	500	-
10.1 c) iv)(Shrinkage test : Crack Observed - 10810:Part 12)	-	500	-
10.1 c) v)(Water ahsorption (Gravimetric) - IS 10810: Part 33 )	-	500	-
10.1 d) i)(Physical test for PE insulation: Tensile strength - IS 10810: Part 7 )	-	500	-
10.1 d) i)(Physical test for PE insulation: elongation at break - IS 10810: Part 7)	-	500	-
10.1 d) ii)(Melt flow index- IS 10810: Part 23)	-	500	-
10.1 d) iv)(Vicat softening point -IS 10810: Part 22)	-	500	-
10.1 d) v)(Environmental stress cracking -IS 10810:Part29)	-	500	-
10.1 f)(Insulation resistance (Volume resistivity) test a) volume resistivity at 27°C - IS 10810: Part 43)	-	500	-
10.1 f)(Insulation resistance (Volume resistivity) test b) volume resistivity at 70°C - IS 10810: Part 43)	-	500	-
10.1 g)(High voltage test - IS10810:Part 45)	-	500	-
11.4(Bending Test on the Completed Cable ( Optional) )	-	500	-
11.4(Bending Test on the Completed Cable ( Optional))	-	500	-
10.1 d) iii)(Carbon Black Content)	-	500	-
6.1(Construction of phase conductor)	-	500	-
6.1(Number of wires (phase conductor))	-	500	-
6.1(Construction of Street Lighting conductor)	-	500	-
6.1(Number of wires (Street Lighting conductor))	-	500	-
12.1(Manufacturer's Identification)	-	500	-
12.2(Cable Identification)	-	500	-
4.1(Phase/Street Lighting conductor)	-	500	-
4.2(Messenger (Neutral Conductor or Otherwise))	-	500	-
5.1(Insulation)	-	500	-
6.1(Flexibility class)	-	500	-
6.2(Compactness)	-	500	-
6.2(No of strands)	-	500	-
6.2(Surface)	-	500	-
6.3(Protective barrier)	-	500	-
6.4(size of street lighting conductor)	-	500	-
6.5(Size of messenger conductor )	-	500	-
6.6(Joints in messenger conductor )	-	500	-
6.6(Direction of outer layer)	-	500	-
7.1(Insulation)	-	500	-
7.2( Thickness of insulation)	-	500	-
7.3(Tolerance on thickness of insulation )	-	500	-
7.4(Aplication of the insulation )	-	500	-
7.5(Colour of the insulation )	-	500	-
8.1(Core identification)	-	500	-
8.2(Core identification)	-	500	-
8.3(Identification by other means)	-	500	-
9.1(Assembly (Laying up))	-	500	-
9.2(Assembly (Laying up))	-	500	-
9.3(Direction of lay)	-	500	-
10.1 a) i)(Tests on phase/street light conductor: tensile test - Test method IS10810:Part 2)	-	500	-
10.1 a) ii)(Wrapping test - 10810: Part 3)	-	500	-
10.1 a) iii)(Resistance test - IS10810: Part 5)	-	500	-
10.1 b) i)(Test on messenger conductor: Breaking load - IS 10810: Part 2)	-	500	-
10.1 b) ii)(Test on messenger conductor: Elongation test - Cl 11.3)	-	500	-
10.1 b) iii)(Test on messenger conductor: Resistance test - IS 10810: Part 5)	-	500	-
10.1 c) i)(Physical tests for XLPE Insulation: Tensile strength - IS 10810: Part 7)	-	500	-
10.1 c) i)(Physical tests for XLPE Insulation: elongation at break - IS 10810: part 7)	-	500	-
10.1 c) ii)(Ageing in air oven : Tensile strength variation - IS 10810:Part 11)	-	2000	-
10.1 c) ii)(Ageing in air oven : Elongation variation- IS 10810: Part 11)	-	2000	-
10.1 c) iii)(Hot set test: Elongation under load - IS 10810: Part 30)	-	1000	-
10.1 c) iii)(Hot set test: Permanent elongation (set) after cooling - IS 10810: Part 30)	-	1000	-
10.1 c) iv)(Shrinkage test : Shrinkage - 10810:Part 12)	-	500	-
10.1 c) iv)(Shrinkage test : Crack Observed - 10810:Part 12)	-	500	-
10.1 c) v)(Water ahsorption (Gravimetric) - IS 10810: Part 33 )	-	3000	-
10.1 d) i)(Physical test for PE insulation: Tensile strength - IS 10810: Part 7 )	-	500	-
10.1 d) i)(Physical test for PE insulation: elongation at break - IS 10810: Part 7)	-	500	-
10.1 d) ii)(Melt flow index- IS 10810: Part 23)	-	500	-
10.1 d) iv)(Vicat softening point -IS 10810: Part 22)	-	500	-
10.1 d) v)(Environmental stress cracking -IS 10810:Part29)	-	500	-
10.1 f)(Insulation resistance (Volume resistivity) test a) volume resistivity at 27°C - IS 10810: Part 43)	-	500	-
10.1 f)(Insulation resistance (Volume resistivity) test b) volume resistivity at 70°C - IS 10810: Part 43)	-	500	-
10.1 g)(High voltage test - IS10810:Part 45)	-	1000	-
11.4(Bending Test on the Completed Cable ( Optional) )	-	500	-
11.4(Bending Test on the Completed Cable ( Optional))	-	500	-
10.1 d) iii)(Carbon Black Content)	-	500	-
6.1(Construction of phase conductor)	-	500	-
6.1(Number of wires (phase conductor))	-	500	-
6.1(Construction of Street Lighting conductor)	-	500	-
6.1(Number of wires (Street Lighting conductor))	-	500	-
12.1(Manufacturer's Identification)	-	500	-
12.2(Cable Identification)	-	500	-

15 Jun, 2029

-
Included w.e.f.13.05.2025

IS 17293 (2020)

Electric Cables for Photovoltaic Systems for Rated Voltage 1 500 V d.c.

Electric Cables for Photovoltaic Systems for Rated Voltage 1500 V d.c.

1025000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 7.3, Table 1 to 5 of IS 8130:2013 & IS:10810 (Part 5)-1984(Conductor Resistance Test)	-	5000	-
Cl. 7.1.2 of IS 8130 : 2013 & IS:10810 (Part 1)-1984(Annealing Test (for copper))	-	5000	-
Cl. 7.1.1 of IS 8130:2013 & IS:10810 (Part 4)-1984(Persulphate Test for tinned copper)	-	5000	-
Annex G and Table 3 of IS 17293:2020(Ozone Resistance test)	-	75000	-
IS 191 : 2007, IS 440(Copper purity test)	-	6000	-
Table 3 of IS 17293:2020 & IS 10810 (Part 63)(Smoke density test.)	-	10000	-
Cl 6.4.3 and Table 3 of IS 8130(Diameter of wire in conductor)	-	5000	-
Table-3 & Annex-F of IS 17293:2020 and IS 10810 (Part 7) 1984(Elongation at low temperature (Cold Elongation))	-	5000	-
Annex H and Table 3 of IS 17293:2020(Damp Heat test)	-	75000	-
Cl. 5.3, 6.3 & Table 1 & 2 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	5000	-
Annex A of IS 17293-2020, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	8000	-
Cl 11.2.3 & Table-3 of IS 17293:2020 & IS:10810 (Part 43)-1984(Insulation Resistance)	-	8000	-
Annex B of IS 17293:2020 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	10000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(pH)	-	10000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(IS 17293)	-	5000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(HCl and HBr)	-	10000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Presence of Fluorine / Fluorine Content (if required))	-	10000	-
Annex B of IS 17293:2020 & IS:10810 (Part 30)-1984(IS 10810-30)	-	5000	-
"Annex B of IS 17293:2020 & IS:8504-1:2012 and IS: 8504-2: 2013"(Thermal endurance test)	-	500000	-
Annex D and Table 3 of IS 17293:2020(Dynamic Penetration test)	-	15000	-
Annex- I, Annex-B, Table-11 of IS 17293:2020 and IS 10810 (Part 1) : 1984(Sheath resistance against acid and alkaline solution)	-	5000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Conductivity)	-	5000	-
Annex C of IS 17293:2020 & IS:10810 (Part 21)-1984(Cold impact test)	-	5000	-
Annex - B of IS 17293:2020(Compatibility test)	-	5000	-
Table 3 of IS 17293:2020 & IS:10810 (Part 12)-1984(Shrinkage test)	-	5000	-
Annex - E of IS 17293 : 2020(UV resistance)	-	50000	-
Cl 11.2.1 of IS 17293:2020 & IS:10810 (Part 45)-1984(High voltage test)	-	15000	-
Table 3 of IS 17293:2020 & IS:10810 (Part 20)-1984(Cold bend test)	-	5000	-
Cl. 5.3, 6.3 & Table 1 & 2 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	5000	-
Cl 5.3 of IS 17048:2018 & IS:10810 (Part 53)-1984(Flammability Test)	-	5000	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Presence of Fluorine / Fluorine Content (if required))	-	5000	-
Annex B of IS 17293:2020 & IS:10810 (Part 30)-1984(Hot set test)	-	5000	-
Annex A of IS 17293-2020, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	5000	-
Annex B of IS 17293:2020 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	5000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(pH)	-	5000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(HCl and HBr)	-	5000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Presence of Fluorine / Fluorine Content (if required))	-	5000	-
"Annex B of IS 17293:2020 & IS:8504-1:2012 and IS: 8504-2: 2013"(Thermal endurance test)	-	500000	-
Annex- I, Annex-B, Table-11 of IS 17293:2020 and IS 10810 (Part 1) : 1984(Sheath resistance against acid and alkaline solution)	-	5000	-
Annex - B of IS 17293:2020(Compatibility test)	-	5000	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(pH)	-	5000	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Conductivity)	-	5000	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(HCl and HBr)	-	5000	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Presence of Fluorine / Fluorine Content (if required))	-	5000	-
11.2.2(Spark Test)	-	5000	-
11.2.4(Long-term Resistance of Insulation to d.c.)	-	5000	-
11.2.5(Surface Resistance of Sheath)	-	5000	-
11.3.1(Sheath Colour)	-	5000	-
11.3.2(Sheath Marking)	-	5000	-
11.3.3(Overall Diameters and Ovality)	-	5000	-
Annex J(Assessment of Halogens)	-	5000	-
5.1, 6.1, Table 11, 1.1(Properties before ageing b)	-	5000	-
5.1, 6.1, Table 11, 1.2(Properties after ageing in oven)	-	5000	-
5.1, 6.1, Table 11, 1.3(Hot set test b)	-	5000	-
5.1, 6.1, Table 11, 1.4(Thermal endurance Test conditions b)	-	5000	-
5.1, 6.1, Table 11, 1.5(Bending at low temperature)	-	5000	-
5.1, 6.1, Table 11, 1.6(Elongation at low temperature Insulated conductor/cable overall diameter)	-	5000	-
5.1, 6.1, Table 11, 1.7(Sheath resistance against acid and alkaline solution)	-	5000	-
5.1, 6.1, Table 11, 1.8(Compatibility test)	-	5000	-
5.2(Application to the Conductor)	-	5000	-
5.3(Thickness)	-	5000	-
6.2(Sheath application)	-	5000	-
6.3(Sheath Thickness)	-	5000	-
6.4(Sheath Colour)	-	5000	-
7(Overall Dimension)	-	5000	-
8.1(Continuity of Marking)	-	5000	-
8.2(Durability)	-	5000	-
8.3(Legibility)	-	5000	-
9(Core Identification)	-	5000	-
12(Packing and Marking)	-	5000	-
4.1(Resistance)	-	5000	-
7.1.2.1, 7.2.3(Annealing)	-	5000	-
Table 3, (IS 10810 Part 53)(Test for vertical flame propagation on complete cable)	-	5000	-
Cl. 7.3, Table 1 to 5 of IS 8130:2013 & IS:10810 (Part 5)-1984(Conductor Resistance Test)	-	5000	-
Cl. 7.1.2 of IS 8130 : 2013 & IS:10810 (Part 1)-1984(Annealing Test (for copper))	-	5000	-
Cl. 7.1.1 of IS 8130:2013 & IS:10810 (Part 4)-1984(Persulphate Test for tinned copper)	-	5000	-
Annex G and Table 3 of IS 17293:2020(Ozone Resistance test)	-	50000	-
IS 191 : 2007, IS 440(Copper purity test)	-	5000	-
Table 3 of IS 17293:2020 & IS 10810 (Part 63)(Smoke density test.)	-	5000	-
Cl 6.4.3 and Table 3 of IS 8130(Diameter of wire in conductor)	-	5000	-
Table-3 & Annex-F of IS 17293:2020 and IS 10810 (Part 7) 1984(Elongation at low temperature (Cold Elongation))	-	500	-
Annex H and Table 3 of IS 17293:2020(Damp Heat test)	-	500	-
Cl. 5.3, 6.3 & Table 1 & 2 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	5000	-
Annex A of IS 17293-2020, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	5000	-
Cl 11.2.3 & Table-3 of IS 17293:2020 & IS:10810 (Part 43)-1984(Insulation Resistance)	-	5000	-
Annex B of IS 17293:2020 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	5000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(pH)	-	5000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(IS 17293)	-	5000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(HCl and HBr)	-	5000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Presence of Fluorine / Fluorine Content (if required))	-	5000	-
Annex B of IS 17293:2020 & IS:10810 (Part 30)-1984(IS 10810-30)	-	5000	-
"Annex B of IS 17293:2020 & IS:8504-1:2012 and IS: 8504-2: 2013"(Thermal endurance test)	-	5000	-
Annex D and Table 3 of IS 17293:2020(Dynamic Penetration test)	-	5000	-
Annex- I, Annex-B, Table-11 of IS 17293:2020 and IS 10810 (Part 1) : 1984(Sheath resistance against acid and alkaline solution)	-	5000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Conductivity)	-	5000	-
Annex C of IS 17293:2020 & IS:10810 (Part 21)-1984(Cold impact test)	-	5000	-
Annex - B of IS 17293:2020(Compatibility test)	-	5000	-
Table 3 of IS 17293:2020 & IS:10810 (Part 12)-1984(Shrinkage test)	-	5000	-
Annex - E of IS 17293 : 2020(UV resistance)	-	50000	-
Cl 11.2.1 of IS 17293:2020 & IS:10810 (Part 45)-1984(High voltage test)	-	5000	-
Table 3 of IS 17293:2020 & IS:10810 (Part 20)-1984(Cold bend test)	-	5000	-
Cl. 5.3, 6.3 & Table 1 & 2 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	5000	-
Cl 5.3 of IS 17048:2018 & IS:10810 (Part 53)-1984(Flammability Test)	-	5000	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Presence of Fluorine / Fluorine Content (if required))	-	5000	-
Annex B of IS 17293:2020 & IS:10810 (Part 30)-1984(Hot set test)	-	5000	-
Annex A of IS 17293-2020, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	5000	-
Annex B of IS 17293:2020 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	5000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(pH)	-	5000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(HCl and HBr)	-	5000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Presence of Fluorine / Fluorine Content (if required))	-	5000	-
"Annex B of IS 17293:2020 & IS:8504-1:2012 and IS: 8504-2: 2013"(Thermal endurance test)	-	5000	-
Annex- I, Annex-B, Table-11 of IS 17293:2020 and IS 10810 (Part 1) : 1984(Sheath resistance against acid and alkaline solution)	-	5000	-
Annex - B of IS 17293:2020(Compatibility test)	-	5000	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(pH)	-	5000	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Conductivity)	-	5000	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(HCl and HBr)	-	5000	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Presence of Fluorine / Fluorine Content (if required))	-	5000	-
11.2.2(Spark Test)	-	5000	-
11.2.4(Long-term Resistance of Insulation to d.c.)	-	5000	-
11.2.5(Surface Resistance of Sheath)	-	5000	-
11.3.1(Sheath Colour)	-	5000	-
11.3.2(Sheath Marking)	-	5000	-
11.3.3(Overall Diameters and Ovality)	-	5000	-
Annex J(Assessment of Halogens)	-	5000	-
5.1, 6.1, Table 11, 1.1(Properties before ageing b)	-	5000	-
5.1, 6.1, Table 11, 1.2(Properties after ageing in oven)	-	5000	-
5.1, 6.1, Table 11, 1.3(Hot set test b)	-	5000	-
5.1, 6.1, Table 11, 1.4(Thermal endurance Test conditions b)	-	5000	-
5.1, 6.1, Table 11, 1.5(Bending at low temperature)	-	5000	-
5.1, 6.1, Table 11, 1.6(Elongation at low temperature Insulated conductor/cable overall diameter)	-	5000	-
5.1, 6.1, Table 11, 1.7(Sheath resistance against acid and alkaline solution)	-	5000	-
5.1, 6.1, Table 11, 1.8(Compatibility test)	-	50000	-
5.2(Application to the Conductor)	-	5000	-
5.3(Thickness)	-	5000	-
6.2(Sheath application)	-	5000	-
6.3(Sheath Thickness)	-	5000	-
6.4(Sheath Colour)	-	5000	-
7(Overall Dimension)	-	5000	-
8.1(Continuity of Marking)	-	5000	-
8.2(Durability)	-	5000	-
8.3(Legibility)	-	5000	-
9(Core Identification)	-	5000	-
12(Packing and Marking)	-	5000	-
4.1(Resistance)	-	500	-
7.1.2.1, 7.2.3(Annealing)	-	500	-
Table 3, (IS 10810 Part 53)(Test for vertical flame propagation on complete cable)	-	5000	-
Cl. 7.3, Table 1 to 5 of IS 8130:2013 & IS:10810 (Part 5)-1984(Conductor Resistance Test)	-	5000	-
Cl. 7.1.2 of IS 8130 : 2013 & IS:10810 (Part 1)-1984(Annealing Test (for copper))	-	5000	-
Cl. 7.1.1 of IS 8130:2013 & IS:10810 (Part 4)-1984(Persulphate Test for tinned copper)	-	5000	-
Annex G and Table 3 of IS 17293:2020(Ozone Resistance test)	-	5000	-
IS 191 : 2007, IS 440(Copper purity test)	-	5000	-
Table 3 of IS 17293:2020 & IS 10810 (Part 63)(Smoke density test.)	-	5000	-
Cl 6.4.3 and Table 3 of IS 8130(Diameter of wire in conductor)	-	5000	-
Table-3 & Annex-F of IS 17293:2020 and IS 10810 (Part 7) 1984(Elongation at low temperature (Cold Elongation))	-	5000	-
Annex H and Table 3 of IS 17293:2020(Damp Heat test)	-	5000	-
Cl. 5.3, 6.3 & Table 1 & 2 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	5000	-
Annex A of IS 17293-2020, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	5000	-
Cl 11.2.3 & Table-3 of IS 17293:2020 & IS:10810 (Part 43)-1984(Insulation Resistance)	-	5000	-
Annex B of IS 17293:2020 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	5000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(pH)	-	5000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(IS 17293)	-	5000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(HCl and HBr)	-	5000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Presence of Fluorine / Fluorine Content (if required))	-	5000	-
Annex B of IS 17293:2020 & IS:10810 (Part 30)-1984(IS 10810-30)	-	5000	-
"Annex B of IS 17293:2020 & IS:8504-1:2012 and IS: 8504-2: 2013"(Thermal endurance test)	-	500000	-
Annex D and Table 3 of IS 17293:2020(Dynamic Penetration test)	-	5000	-
Annex- I, Annex-B, Table-11 of IS 17293:2020 and IS 10810 (Part 1) : 1984(Sheath resistance against acid and alkaline solution)	-	5000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Conductivity)	-	5000	-
Annex C of IS 17293:2020 & IS:10810 (Part 21)-1984(Cold impact test)	-	5000	-
Annex - B of IS 17293:2020(Compatibility test)	-	5000	-
Table 3 of IS 17293:2020 & IS:10810 (Part 12)-1984(Shrinkage test)	-	5000	-
Annex - E of IS 17293 : 2020(UV resistance)	-	5000	-
Cl 11.2.1 of IS 17293:2020 & IS:10810 (Part 45)-1984(High voltage test)	-	5000	-
Table 3 of IS 17293:2020 & IS:10810 (Part 20)-1984(Cold bend test)	-	5000	-
Cl. 5.3, 6.3 & Table 1 & 2 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	5000	-
Cl 5.3 of IS 17048:2018 & IS:10810 (Part 53)-1984(Flammability Test)	-	5000	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Presence of Fluorine / Fluorine Content (if required))	-	5000	-
Annex B of IS 17293:2020 & IS:10810 (Part 30)-1984(Hot set test)	-	5000	-
Annex A of IS 17293-2020, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	5000	-
Annex B of IS 17293:2020 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	5000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(pH)	-	5000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(HCl and HBr)	-	5500	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Presence of Fluorine / Fluorine Content (if required))	-	5000	-
"Annex B of IS 17293:2020 & IS:8504-1:2012 and IS: 8504-2: 2013"(Thermal endurance test)	-	5000	-
Annex- I, Annex-B, Table-11 of IS 17293:2020 and IS 10810 (Part 1) : 1984(Sheath resistance against acid and alkaline solution)	-	5000	-
Annex - B of IS 17293:2020(Compatibility test)	-	5000	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(pH)	-	5000	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Conductivity)	-	5000	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(HCl and HBr)	-	5000	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Presence of Fluorine / Fluorine Content (if required))	-	5000	-
11.2.2(Spark Test)	-	5000	-
11.2.4(Long-term Resistance of Insulation to d.c.)	-	5000	-
11.2.5(Surface Resistance of Sheath)	-	5000	-
11.3.1(Sheath Colour)	-	5000	-
11.3.2(Sheath Marking)	-	500	-
11.3.3(Overall Diameters and Ovality)	-	5000	-
Annex J(Assessment of Halogens)	-	5000	-
5.1, 6.1, Table 11, 1.1(Properties before ageing b)	-	5000	-
5.1, 6.1, Table 11, 1.2(Properties after ageing in oven)	-	5000	-
5.1, 6.1, Table 11, 1.3(Hot set test b)	-	5000	-
5.1, 6.1, Table 11, 1.4(Thermal endurance Test conditions b)	-	500000	-
5.1, 6.1, Table 11, 1.5(Bending at low temperature)	-	5000	-
5.1, 6.1, Table 11, 1.6(Elongation at low temperature Insulated conductor/cable overall diameter)	-	5000	-
5.1, 6.1, Table 11, 1.7(Sheath resistance against acid and alkaline solution)	-	5000	-
5.1, 6.1, Table 11, 1.8(Compatibility test)	-	5000	-
5.2(Application to the Conductor)	-	5000	-
5.3(Thickness)	-	5000	-
6.2(Sheath application)	-	5000	-
6.3(Sheath Thickness)	-	5000	-
6.4(Sheath Colour)	-	5000	-
7(Overall Dimension)	-	5000	-
8.1(Continuity of Marking)	-	5000	-
8.2(Durability)	-	5000	-
8.3(Legibility)	-	5000	-
9(Core Identification)	-	5000	-
12(Packing and Marking)	-	5000	-
4.1(Resistance)	-	5000	-
7.1.2.1, 7.2.3(Annealing)	-	5000	-
Table 3, (IS 10810 Part 53)(Test for vertical flame propagation on complete cable)	-	5000	-

15 Jun, 2029

-
Included w.e.f.29.04.2025

IS 302 : Part 1 (2024)

Household and Similar Electrical Appliances â Safety Part 1 General Requirements (Seventh Revision)

49000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
12(Charging of metal-ion batteries)	-	4000	-
6(Classification- IS 302-1)	-	1000	-
5(General conditions for the tests)	-	500	-
11.8(Temperature rise)	-	500	-
11.7(Duration corresponding)	-	500	-
11.6(Combined appliances)	-	500	-
11.5(Motor-operated appliances)	-	500	-
11.4(Heating appliances)	-	500	-
8.1.5(Live parts of built-in appliances)	-	500	-
18(Endurance)	-	2000	-
17(Overload protection of transformers and associated circuits)	-	500	-
16(Leakage current and electric strength)	-	500	-
4(General requirement)	-	500	-
32.1(Radiation Toxicity and Similar Hazards)	-	500	-
31(Resistance to Rusting)	-	500	-
30.2(Needle Flame Test)	-	1000	-
30.2(Glow Wire Test)	-	1000	-
30.1(Ball pressure test)	-	1000	-
29(clearance, creepage distances and solid insulation)	-	500	-
28(Screw test and connections)	-	500	-
27.1(Provision for Earthing, IS 302-1)	-	1000	-
26(Terminals for external conductors)	-	500	-
25.8(Supply Connection and External Flexible Cords, IS 302-1)	-	500	-
24(Components)	-	500	-
23.1(Internal Wiring, IS 302-1)	-	500	-
22.1(Construction, IS 302-1)	-	500	-
21.1(Mechanical Strength, IS 302-1)	-	500	-
20.1(Stability & Mechanical Hazards, IS 302-1)	-	500	-
19(Abnormal Operation)	-	500	-
18(Endurance)	-	500	-
17(Over Load Protection of Transformers and associated circuits)	-	500	-
16.3(Electric Strength (after clause 15 and 16.2))	-	500	-
16.2(Leakage Current (after Clause 15))	-	500	-
16.1(General)	-	500	-
15.3(Humidity Test)	-	500	-
15.2(Spillage Test)	-	500	-
15.1(Ingress Protection test other than IPX0 (IP test))	-	500	-
15.0(Moisture resistance)	-	500	-
14(Transient Over Voltages)	-	500	-
13.3(Electric Strength at operating temperature)	-	500	-
13.2(Leakage current at operating temperature)	-	500	-
13(Leakage current and electric strength at operating temperature)	-	500	-
11.3(Heating)	-	500	-
11.2(General)	-	500	-
11.1(General)	-	500	-
10.2(Current input)	-	1000	-
10.1(Power input)	-	1000	-
9(Starting of motor operation test requirements and tests)	-	500	-
8.1.4(Protection against live parts against protective impedance)	-	500	-
8.1.3(Protection against live parts in visible glowing heating elements)	-	500	-
8.1.2(Protection against live parts in openings)	-	500	-
8.1.1(Protection against live parts in all positions)	-	500	-
7(Marking and instructions)	-	500	-
A.2(Earth continuity test)	-	500	-
Annex C(Ageing test on motors)	-	500	-
Annex D(Thermal motor protectors)	-	500	-
15.2(Moisture resistance)	-	500	-
19.17(Abnormal Operation, IS 302-1)	-	1000	-
20.2(Stability & Mechanical Hazards, IS 302-1)	-	500	-
21.2(Mechanical Strength, IS 302-1)	-	500	-
21.3(Mechanical Strength, IS 302-1)	-	500	-
22.5(Construction)	-	500	-
22.6(Construction, IS 302-1)	-	500	-
22.11(Construction, IS 302-1)	-	500	-
22.16(Construction)	-	500	-
22.32(Construction, IS 302-1)	-	500	-
22.42(Construction)	-	500	-
23.3(Internal Wiring, IS 302-1)	-	500	-
25.6(Supply connection and external flexible cords, IS 302-1)	-	500	-
25.7(Supply Connection and External Flexible Cords, IS 302-1)	-	500	-
25.14(Supply Connection and External Flexible Cords, IS 302-1)	-	500	-
25.15(Supply Connection and External Flexible Cords, IS 302-1)	-	500	-
26.5(Terminals for external conductors)	-	500	-
27.5(Provision for Earthing, IS 302-1)	-	500	-
28.1(Screws and connections)	-	500	-
22.2(Construction, IS 302-1)	-	500	-
22.3(Construction, IS 302-1)	-	500	-
B.22.4(Construction, IS 302-1)	-	500	-
B.22.5(Construction, IS 302-1)	-	500	-
16.0(General)	-	500	-
12(Charging of metal-ion batteries)	-	4000	-
6(Classification- IS 302-1)	-	1000	-
5(General conditions for the tests)	-	500	-
11.8(Temperature rise)	-	500	-
11.7(Duration corresponding)	-	500	-
11.6(Combined appliances)	-	500	-
11.5(Motor-operated appliances)	-	500	-
11.4(Heating appliances)	-	500	-
8.1.5(Live parts of built-in appliances)	-	500	-
18(Endurance)	-	2000	-
17(Overload protection of transformers and associated circuits)	-	500	-
16(Leakage current and electric strength)	-	500	-
4(General requirement)	-	500	-
32.1(Radiation Toxicity and Similar Hazards)	-	500	-
31(Resistance to Rusting)	-	500	-
30.2(Needle Flame Test)	-	1000	-
30.2(Glow Wire Test)	-	1000	-
30.1(Ball pressure test)	-	1000	-
29(clearance, creepage distances and solid insulation)	-	500	-
28(Screw test and connections)	-	500	-
27.1(Provision for Earthing, IS 302-1)	-	1000	-
26(Terminals for external conductors)	-	500	-
25.8(Supply Connection and External Flexible Cords, IS 302-1)	-	500	-
23.1(Internal Wiring, IS 302-1)	-	500	-
22.1(Construction, IS 302-1)	-	500	-
21.1(Mechanical Strength, IS 302-1)	-	500	-
20.1(Stability & Mechanical Hazards, IS 302-1)	-	500	-
19(Abnormal Operation)	-	500	-
18(Endurance)	-	500	-
17(Over Load Protection of Transformers and associated circuits)	-	500	-
16.3(Electric Strength (after clause 15 and 16.2))	-	500	-
16.2(Leakage Current (after Clause 15))	-	500	-
16.1(General)	-	500	-
15.3(Humidity Test)	-	500	-
15.2(Spillage Test)	-	500	-
15.1(Ingress Protection test other than IPX0 (IP test))	-	500	-
15.0(Moisture resistance)	-	500	-
14(Transient Over Voltages)	-	500	-
13.3(Electric Strength at operating temperature)	-	500	-
13.2(Leakage current at operating temperature)	-	500	-
13(Leakage current and electric strength at operating temperature)	-	500	-
11.3(Heating)	-	500	-
11.2(General)	-	500	-
11.1(General)	-	500	-
10.2(Current input)	-	1000	-
10.1(Power input)	-	1000	-
9(Starting of motor operation test requirements and tests)	-	500	-
8.1.4(Protection against live parts against protective impedance)	-	500	-
8.1.3(Protection against live parts in visible glowing heating elements)	-	500	-
8.1.2(Protection against live parts in openings)	-	500	-
8.1.1(Protection against live parts in all positions)	-	500	-
7(Marking and instructions)	-	500	-
A.2(Earth continuity test)	-	500	-
Annex C(Ageing test on motors)	-	500	-
Annex D(Thermal motor protectors)	-	500	-
15.2(Moisture resistance)	-	500	-
19.17(Abnormal Operation, IS 302-1)	-	1000	-
20.2(Stability & Mechanical Hazards, IS 302-1)	-	500	-
21.2(Mechanical Strength, IS 302-1)	-	500	-
21.3(Mechanical Strength, IS 302-1)	-	500	-
22.5(Construction)	-	500	-
22.6(Construction, IS 302-1)	-	500	-
22.11(Construction, IS 302-1)	-	500	-
22.16(Construction)	-	500	-
22.32(Construction, IS 302-1)	-	500	-
22.42(Construction)	-	500	-
23.3(Internal Wiring, IS 302-1)	-	500	-
25.6(Supply connection and external flexible cords, IS 302-1)	-	500	-
25.7(Supply Connection and External Flexible Cords, IS 302-1)	-	500	-
25.14(Supply Connection and External Flexible Cords, IS 302-1)	-	500	-
25.15(Supply Connection and External Flexible Cords, IS 302-1)	-	500	-
26.5(Terminals for external conductors)	-	500	-
27.5(Provision for Earthing, IS 302-1)	-	500	-
28.1(Screws and connections)	-	500	-
22.2(Construction, IS 302-1)	-	500	-
22.3(Construction, IS 302-1)	-	500	-
B.22.4(Construction, IS 302-1)	-	500	-
B.22.5(Construction, IS 302-1)	-	500	-
16.0(General)	-	500	-

15 Jun, 2029

-
included .w.e.f. 24.02.2025 EXCLUSION CL 19.11.4.1 (Electrostatic discharges) CL 19.11.4.2 (Radiated fields), 19.11.4.3 (Fast transient bursts), 19.11.4.4 (Surge immunity test), CL 19.11.4.5 (Immunity to conducted discharges) CL 19.11.4.6 (Class 3 Voltage dips and interruptions), 24 (Components) "Domestic Electric Clothes Washing Machines (For testing charges please refer part 2 standard in LIMS)"

IS 302 : Part 2 : Sec 7 (2024)

Safety of Household And Similar Electrical Appliances Part 2 Particular Requirements Section 7: Domestic Electric Clothes Washing Machines

70000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(GENERAL REQUIREMENT)	-	1000	-
6(CLASSIFICATION)	-	2000	-
7(MARKING AND INSTRUCTIONS)	-	2000	-
8(PROTECTION AGAINST ACCESS TO LIVE PARTS)	-	3000	-
10(POWER INPUT AND CURRENT)	-	5000	-
11(HEATING)	-	4000	-
13(LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING TEMPERATURE)	-	2000	-
14(TRANSIENT OVERVOLTAGES)	-	2000	-
15(MOISTURE RESISTANCE)	-	2000	-
16(LEAKAGE CURRENT AND ELECTRIC STRENGTH)	-	2000	-
17("OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS ")	-	1500	-
17("OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS ")	-	1500	-
18(ENDURANCE)	-	7000	-
19(ABNORMAL OPERATION)	-	4000	-
20(STABILITY AND MECHANICAL HAZARDS)	-	2000	-
21(MECHANICAL STRENGTH)	-	2000	-
22(CONSTRUCTION)	-	4000	-
23(INTERNAL WIRING)	-	2000	-
24(COMPONENTS)	-	1500	-
25(SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CORDS)	-	2000	-
26(TERMINALS FOR EXTERNAL CONDUCTORS)	-	1500	-
27(PROVISION FOR EARTHING)	-	2000	-
28(SCREWS AND CONNECTIONS)	-	2000	-
29(CLEARANCES, CREEPAGE DISTANCES AND SOLID INSULATION)	-	2000	-
30(RESISTANCE TO HEAT AND FIRE)	-	2000	-
31(RESISTANCE TO RUSTING)	-	1000	-
19.13(ABNORMAL OPERATION)	-	1000	-
19.101(Abnormal Operation)	-	1000	-
19.102(Abnormal Operation)	-	1000	-
19.11.4.4(Surge immunity test)	-	1000	-
19.11.4.7(Harmonics)	-	1000	-
19.11.4.3(Fast transient bursts)	-	1000	-
4(GENERAL REQUIREMENT)	-	1000	-
6(CLASSIFICATION)	-	2000	-
7(MARKING AND INSTRUCTIONS)	-	2000	-
8(PROTECTION AGAINST ACCESS TO LIVE PARTS)	-	3000	-
10(POWER INPUT AND CURRENT)	-	5000	-
11(HEATING)	-	4000	-
13(LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING TEMPERATURE)	-	2000	-
14(TRANSIENT OVERVOLTAGES)	-	2000	-
15(MOISTURE RESISTANCE)	-	2000	-
16(LEAKAGE CURRENT AND ELECTRIC STRENGTH)	-	2000	-
17("OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS ")	-	1500	-
17("OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS ")	-	1500	-
18(ENDURANCE)	-	7000	-
19(ABNORMAL OPERATION)	-	4000	-
20(STABILITY AND MECHANICAL HAZARDS)	-	2000	-
21(MECHANICAL STRENGTH)	-	2000	-
22(CONSTRUCTION)	-	4000	-
23(INTERNAL WIRING)	-	2000	-
24(COMPONENTS)	-	1500	-
25(SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CORDS)	-	2000	-
26(TERMINALS FOR EXTERNAL CONDUCTORS)	-	1500	-
27(PROVISION FOR EARTHING)	-	2000	-
28(SCREWS AND CONNECTIONS)	-	2000	-
29(CLEARANCES, CREEPAGE DISTANCES AND SOLID INSULATION)	-	2000	-
30(RESISTANCE TO HEAT AND FIRE)	-	2000	-
31(RESISTANCE TO RUSTING)	-	1000	-
19.13(ABNORMAL OPERATION)	-	1000	-
19.101(Abnormal Operation)	-	1000	-
19.102(Abnormal Operation)	-	1000	-
19.11.4.4(Surge immunity test)	-	1000	-
19.11.4.7(Harmonics)	-	1000	-
19.11.4.3(Fast transient bursts)	-	1000	-
32(RADIATION, TOXICITY AND SIMILAR HAZARDS)	-	1000	-
4(GENERAL REQUIREMENT)	-	1000	-
6(CLASSIFICATION)	-	2000	-
7(MARKING AND INSTRUCTIONS)	-	2000	-
8(PROTECTION AGAINST ACCESS TO LIVE PARTS)	-	3000	-
10(POWER INPUT AND CURRENT)	-	5000	-
11(HEATING)	-	4000	-
13(LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING TEMPERATURE)	-	2000	-
14(TRANSIENT OVERVOLTAGES)	-	2000	-
15(MOISTURE RESISTANCE)	-	2000	-
16(LEAKAGE CURRENT AND ELECTRIC STRENGTH)	-	2000	-
17("OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS ")	-	1500	-
17("OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS ")	-	1500	-
18(ENDURANCE)	-	7000	-
19(ABNORMAL OPERATION)	-	4000	-
20(STABILITY AND MECHANICAL HAZARDS)	-	2000	-
21(MECHANICAL STRENGTH)	-	2000	-
22(CONSTRUCTION)	-	4000	-
23(INTERNAL WIRING)	-	2000	-
24(COMPONENTS)	-	1500	-
25(SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CORDS)	-	2000	-
26(TERMINALS FOR EXTERNAL CONDUCTORS)	-	1500	-
27(PROVISION FOR EARTHING)	-	2000	-
28(SCREWS AND CONNECTIONS)	-	2000	-
29(CLEARANCES, CREEPAGE DISTANCES AND SOLID INSULATION)	-	2000	-
30(RESISTANCE TO HEAT AND FIRE)	-	2000	-
31(RESISTANCE TO RUSTING)	-	1000	-
19.13(ABNORMAL OPERATION)	-	1000	-
19.101(Abnormal Operation)	-	1000	-
19.102(Abnormal Operation)	-	1000	-
19.11.4.4(Surge immunity test)	-	1000	-
19.11.4.7(Harmonics)	-	1000	-
19.11.4.3(Fast transient bursts)	-	1000	-
32(RADIATION, TOXICITY AND SIMILAR HAZARDS)	-	1000	-

15 Jun, 2029

-
included .W.E.F.11.12.2024 EXCLUSION CL 19.11.4.1 (Electrostatic discharges) CL 19.11.4.2 (Radiated fields) CL 19.11.4.5 (Immunity to conducted discharges) CL 19.11.4.6 (Class 3 Voltage dips and interruptions)

IS 3854 (2023)

Switches for Domestic and Similar Purposes - Specification (Third Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(General Requirements)	-	300	-
Cl-5(General notes on tests)	-	200	-
Cl-6(Rating)	-	500	-
Cl-7(Classification)	-	200	-
Cl-8(Marking)	-	300	-
Cl-9(Checking of dimensions)	-	500	-
Cl-10.1, 10.2(Prevention of Access to Live Parts)	-	500	-
Cl-10.3(Requirements for Accessible Metal Parts)	-	300	-
Cl-10.4(Requirements for Insulation of the Mechanism)	-	200	-
Cl. 10.5(Requirements for Insulation of the Mechanism with Respect to the Surrounding Environment)	-	300	-
Cl-10.6(Requirements for Switches Operated Indirectly)	-	200	-
Cl-10.7(Requirements for Switches with Replaceable Pull Cord)	-	500	-
Cl-11(Provision for earthing)	-	500	-
Cl-12(Terminals)	-	1000	-
Cl-13(Constructional requirements)	-	1000	-
Cl-14(Mechanism)	-	1000	-
Cl-15.1(Resistance to Ageing)	-	1000	-
Cl-15.2(Protection Provided by Enclosures of Switches)	-	500	-
Cl-15.3(Resistance to Humidity)	-	1000	-
Cl-16.1(General)	-	500	-
Cl-16.2(Test for Measuring the Insulation Resistance)	-	500	-
Cl-16.3(Electric Strength Test)	-	500	-
Cl-17(Temperature rise)	-	1000	-
Cl-18(Making and breaking capacity)	-	1000	-
Cl-19(Normal operation)	-	1000	-
Cl-20(Mechanical strength)	-	200	-
Cl-21(Resistance to heat)	-	500	-
Cl-22(Screws, current carrying parts and connections)	-	300	-
Cl-23(Creepage distances, clearances and distance through sealing compound)	-	200	-
Cl-24.1(Resistance to abnormal heat and fire)	-	500	-
Cl-24.2(Resistance to tracking)	-	200	-
Cl-25(Resistance to rusting)	-	300	-
19.1(Test for Switches Intended for Inductive Loads)	-	500	-
19.2(Test for Switches Intended for Externally Ballasted Lamp Loads)	-	1000	-
19.3(Test for Switches Intended for Self-ballasted Lamp Loads)	-	1000	-
13.5(Attachment of knobs)	-	500	-
12.3.11(Table 11)(Test Current for the Verification of Electrical and Thermal Stresses in Normal Use of Screwless Terminals)	-	500	-
12.3.12(Table 13)(Deflection Test Forces)	-	500	-

15 Jun, 2029

-
Revised version of IS 3854:2023 Included w.e.f. 01.10.2024

IS 302 : Part 2 : Sec 21 (2024)

Household and Similar Electrical Appliancesï¿½Safety Part 2 Particular Requirements Section 21 Storage Water Heaters

ALL

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(General requirement)	-	300	-
5(General conditions for the tests)	-	200	-
6(Classification)	-	500	-
7(Marking and instructions)	-	500	-
8(Protection against access to live parts)	-	500	-
10(Power input and current)	-	1000	-
11(Heating)	-	1000	-
13(Leakage current and electric strength at operating temperature)	-	500	-
14(Transient overvoltages)	-	1000	-
15(Moisture resistance)	-	1000	-
16(Leakage current and electric strength)	-	500	-
17(Overload protection of transformers and associated circuits)	-	500	-
19(Abnormal operation)	-	1000	-
20(Stability and mechanical hazards)	-	500	-
21(Mechanical strength)	-	500	-
22(Construction)	-	1000	-
23(Internal wiring)	-	500	-
25(Supply connection and external flexible cords)	-	500	-
26(Terminals for external conductors)	-	500	-
27(Provision for earthing)	-	1000	-
28(Screws and connections)	-	500	-
29(Clearances, creepage distances and solid insulation)	-	500	-
30(Resistance to heat and fire)	-	1000	-
31(Resistance to rusting)	-	500	-
32(Radiation, toxicity and similar hazards)	-	500	-
18(Endurance)	-	1000	-
9(Starting of motor-operated appliances)	-	500	-
24(Components)	-	500	-
A.101(Pressure test)	-	500	-
19.11.4.3(Fast transient bursts)	-	500	-
19.11.4.4(Surge immunity test)	-	500	-
19.11.4.7(Harmonics)	-	500	-
4(General requirement)	-	300	-
5(General conditions for the tests)	-	200	-
6(Classification)	-	500	-
7(Marking and instructions)	-	500	-
8(Protection against access to live parts)	-	500	-
10(Power input and current)	-	1000	-
11(Heating)	-	1000	-
13(Leakage current and electric strength at operating temperature)	-	500	-
14(Transient overvoltages)	-	1000	-
15(Moisture resistance)	-	1000	-
16(Leakage current and electric strength)	-	500	-
17(Overload protection of transformers and associated circuits)	-	500	-
19(Abnormal operation)	-	1000	-
20(Stability and mechanical hazards)	-	500	-
21(Mechanical strength)	-	500	-
22(Construction)	-	1000	-
23(Internal wiring)	-	500	-
25(Supply connection and external flexible cords)	-	500	-
26(Terminals for external conductors)	-	500	-
27(Provision for earthing)	-	1000	-
28(Screws and connections)	-	500	-
29(Clearances, creepage distances and solid insulation)	-	500	-
30(Resistance to heat and fire)	-	1000	-
31(Resistance to rusting)	-	500	-
32(Radiation, toxicity and similar hazards)	-	500	-
18(Endurance)	-	1000	-
9(Starting of motor-operated appliances)	-	500	-
24(Components)	-	500	-
A.101(Pressure test)	-	500	-
19.11.4.3(Fast transient bursts)	-	500	-
19.11.4.4(Surge immunity test)	-	500	-
19.11.4.7(Harmonics)	-	500	-

15 Jun, 2029

-
Exclusion (Cl.19.11.4.1 to 19.11.4.7) EMI/EMC 24 (Components) (Abnormal Operation)

IS 7809 : Part 3 : Sec 1 (1986)

Specification for pressure sensitive adhesive insulating tapes for electrical purposes: Part 3 requirements or individual materials: Sec 1 plasticized polyvinylchloride tapes with non - Thermosetting adhesive (First Revision)

14500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	1000	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	1000	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	1000	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	1000	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	1000	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	1000	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	1000	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	1000	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	1000	-
2.1.1(Type and Desiganation)	-	1000	-
2.1.2(Type and Desiganation)	-	1000	-
3.1(General Requirments,as per IS 7809 (Part 1 ) :1975 )	-	1000	-
3.2(General Requirments,as per IS 7809 (Part 1 ) :1975 )	-	1000	-
3.3(General Requirments,as per IS 7809 (Part 1 ) :1975 )	-	1000	-
3.4(General Requirments,as per IS 7809 (Part 1 ) :1975 )	-	1000	-
4.1(Performance Requirments)	-	1000	-
4.2(Performance Requirments)	-	1000	-
4.3(Performance Requirments)	-	1000	-
4.4(Performance Requirments)	-	1000	-
4.5(Performance Requirments)	-	1000	-
4.6(Flammability ,Cl 6 of IS 7809 (Part 2): 1977)	-	1000	-
4.6(Flammability ,Cl 6 of IS 7809 (Part 2): 1977)	-	1000	-
4.6(Flammability ,Cl 6 of IS 7809 (Part 2): 1977)	-	1000	-
4.6(Flammability ,Cl 6 of IS 7809 (Part 2): 1977)	-	1000	-
4.7(Electrolytic corrosion)	-	1000	-
4.7(Electrolytic corrosion)	-	1000	-
4.7(Electrolytic corrosion)	-	1000	-
4.8(Stability to accelerated ageing )	-	1000	-
4.9(Insulation resistance test)	-	1000	-
3.1( Minimum Storage Life Cl. 7.1 of IS 7809(Part 1) :1975)	-	1000	-
3.1( Minimum Storage Life Cl. 7.1 of IS 7809(Part 1) :1975)	-	1000	-
3.1(Minimum Storage Life ,Dimensions , Cl. 7.1 of IS 7809(Part 1) :1975)	-	1000	-
3.1(Minimum Storage Life ,Dimensions , Cl. 7.1 of IS 7809(Part 1) :1975)	-	1000	-
3.1(Minimum Storage Life ,Dimensions , Cl. 7.1 of IS 7809(Part 1) :1975)	-	1000	-
3.1(Minimum Storage Life ,Dimensions , Cl. 7.1 of IS 7809(Part 1) :1975)	-	1000	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	1000	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	1000	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	1000	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	1000	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	1000	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	1000	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	1000	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	1000	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	1000	-
2.1.1(Type and Desiganation)	-	1000	-
2.1.2(Type and Desiganation)	-	1000	-
3.1(General Requirments,as per IS 7809 (Part 1 ) :1975 )	-	1000	-
3.2(General Requirments,as per IS 7809 (Part 1 ) :1975 )	-	1000	-
3.3(General Requirments,as per IS 7809 (Part 1 ) :1975 )	-	1000	-
3.4(General Requirments,as per IS 7809 (Part 1 ) :1975 )	-	1000	-
4.1(Performance Requirments)	-	1000	-
4.2(Performance Requirments)	-	1000	-
4.3(Performance Requirments)	-	1000	-
4.4(Performance Requirments)	-	1000	-
4.5(Performance Requirments)	-	1000	-
4.6(Flammability ,Cl 6 of IS 7809 (Part 2): 1977)	-	1000	-
4.6(Flammability ,Cl 6 of IS 7809 (Part 2): 1977)	-	1000	-
4.6(Flammability ,Cl 6 of IS 7809 (Part 2): 1977)	-	1000	-
4.6(Flammability ,Cl 6 of IS 7809 (Part 2): 1977)	-	1000	-
4.7(Electrolytic corrosion)	-	1000	-
4.7(Electrolytic corrosion)	-	1000	-
4.7(Electrolytic corrosion)	-	1000	-
4.8(Stability to accelerated ageing )	-	1000	-
4.9(Insulation resistance test)	-	1000	-
3.1( Minimum Storage Life Cl. 7.1 of IS 7809(Part 1) :1975)	-	1000	-
3.1(Appearance)	-	1000	-
3.1(Freedom from defects)	-	1000	-
3.1(Minimum Storage Life ,Dimensions , Cl. 7.1 of IS 7809(Part 1) :1975)	-	1000	-
3.1(Minimum Storage Life ,Dimensions , Cl. 7.1 of IS 7809(Part 1) :1975)	-	1000	-
3.1(Minimum Storage Life ,Dimensions , Cl. 7.1 of IS 7809(Part 1) :1975)	-	1000	-
3.1(Minimum Storage Life ,Dimensions , Cl. 7.1 of IS 7809(Part 1) :1975)	-	1000	-
Cl.No.4 of IS 7809 (Part 1)-1975(Appearance)	-	1000	-
Cl.No.5 of IS 7809 (Part 1)-1975(Freedom From Deffects)	-	1000	-
Cl.No.3.2(Width)	-	1000	-
Cl.No.3.3(Length)	-	1000	-
Cl.No.3.4(Thickness)	-	1000	-
Cl.No.4.1(Tensile Strength)	-	1000	-
Cl.No.4.2(Adhesion to Steel)	-	1000	-
Cl.No.4.3(Adhesion to backing)	-	1000	-
Cl.No.4.4(Electric Strength at RT)	-	1000	-
Cl.No.4.5(Electric Strength after Humid Conditioning)	-	1000	-
Cl.No.4.6(Flammability)	-	1000	-
Cl.No.4.7()	-	1000	-
Cl.No.4.8(Stability to accelerated ageing)	-	1000	-
Cl.No.4.9(Insulation Resistance)	-	1000	-
Cl.No.7 of IS 7809 (Part 1)-1975(Minimum Storage Life)	-	1000	-
Cl.No.4 of IS 7809 (Part 1)-1975(Appearance after minimum storage Life)	-	1000	-
Cl.No.5 of IS 7809 (Part 1)-1975(Freedom From Deffects after minimum storage Life)	-	1000	-
Cl.No.3.2(Width after minimum storage Life)	-	1000	-
Cl.No.3.3(Length after minimum storage Life)	-	1000	-
Cl.No.3.4(Thickness after minimum storage Life)	-	1000	-
Cl.No.4.1(Tensile Strength after minimum storage Life)	-	1000	-
Cl.No.4.2(Adhesion to Steel after minimum storage Life)	-	1000	-
Cl.No.4.3(Adhesion to backing after minimum storage Life)	-	1000	-
Cl.No.4.4(Electric Strength at RT after minimum storage Life)	-	1000	-
Cl.No.4.5(Electric Strength after Humid Conditioning after minimum storage Life)	-	1000	-
Cl.No.4.6(Flammability after minimum storage Life)	-	1000	-
Cl.No.4.7(Electrolytic Corrosion after minimum storage Life)	-	1000	-
Cl.No.4.8(Stability to accelerated ageing after minimum storage Life)	-	1000	-
Cl.No.4.9(Insulation Resistance after minimum storage Life)	-	1000	-
3.1(Marking)	-	1000	-
3.1( Minimum Storage Life Cl. 7.1 of IS 7809(Part 1) :1975)	-	1000	-

15 Jun, 2029

-
Included w.e.f. 19.09.2024

IS 15787 (2008)

Switch - Socket - Outlets (Non - Interlock Type)

50000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.30 IS 15787:2008(Additional tests on pins providing with insulating sleeves)	-	3000	-
Cl.29 IS 15787:2008(Resistance to Rusting)	-	3000	-
Cl.28 IS 15787:2008(Resistance of insulating material to Abnormal Heat , To Fire & To tracking )	-	3000	-
Cl.27 IS 15787:2008(Creepage distance, clearances & Distance through sealing compounds)	-	3000	-
Cl.26 IS 15787:2008(Screws, current carrying parts & connections)	-	3000	-
Cl.25 IS 15787:2008(Resistance to heat )	-	3000	-
Cl.24 IS 15787:2008(Mechanical strength)	-	3000	-
Cl.23 IS 15787:2008(Flexible cables & their connections)	-	3000	-
Cl.22 IS 15787:2008(Force necessary to withdraw the plug )	-	3000	-
Cl.21 IS 15787:2008(Normal operation )	-	3000	-
Cl.20 IS 15787:2008(Making & Breaking )	-	3000	-
Cl.19 IS 15787:2008(Temperature rise )	-	3000	-
Cl.18 IS 15787:2008(Operation of Earthing Contacts)	-	3000	-
Cl.17 IS 15787:2008(Insulation resistance & electric strength )	-	3000	-
Cl.16 IS 15787:2008(Resistance to ageing,To harmful ingress of water and To Humidity)	-	3000	-
Cl.15 IS 15787:2008(Interlocked Socket-outlet )	-	3000	-
Cl.14 IS 15787:2008(Construction of Plugs and Portable Socket- Outlet )	-	3000	-
Cl.13 IS 15787:2008(Construction of fixed socket outlet)	-	3000	-
Cl.12 IS 15787:2008(Terminals)	-	3000	-
Cl.11 IS 15787:2008(Provision for earthing )	-	3000	-
Cl.10 IS 15787:2008(Protection against to electric shock )	-	3000	-
Cl.9 IS 15787:2008(Checking of dimension)	-	3000	-
Cl.8 IS 15787:2008(Marking )	-	3000	-
Cl.7 IS 15787:2008(Classification)	-	3000	-
Cl.6 IS 15787:2008(Ratings )	-	3000	-

15 Jun, 2029

-
Included w.e.f.11.12.2024

IS 14772 (2020)

Boxes and Enclosures for Electrical Accessories for Household and Similar Fixed Electrical Installations — General Requirements ( First Revision )

27700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1(Nature of material)	-	2000	-
7.2(Type of installation)	-	2000	-
7.3(Types of inlets)	-	2000	-
7.4(Clamping means)	-	2000	-
7.5(Minimum temperature during installation)	-	2000	-
7.6, 7.7, 7.8(The degree of ingress protection)	-	2000	-
7.9(The provision for fixing accessories to the boxes )	-	2000	-
7.1(The method of fixing the terminals)	-	2000	-
8.1(marking)	-	2000	-
8.2(By Inspection and The marking is rubbed by hand 15s width a piece of cloth soaked with water and again for 15s with a piece of cloth soaked with petroleum spirit.)	-	2000	-
8.3(BIS Certification Marking)	-	2000	-
9.0(Dimensions)	-	2000	-
10.0(Protection against electric shock)	-	2000	-
11.0(PROVISION FOR EARTHING)	-	2000	-
12.0(Constructions)	-	2000	-
13.0(Resistance to ingress of solid objects)	-	2000	-
13.0(Resistance toharmful ingress of water)	-	2000	-
13.0(Resistance to ageing)	-	2000	-
14.0(insultation resistance)	-	2000	-
14.0(electric strength)	-	2000	-
15.0(Mechanical strength)	-	2000	-
16.0(resistance to heat)	-	2000	-
17.0(creepage distance)	-	2000	-
17.0(clearances)	-	2000	-
17.0(distance through seating compund)	-	2000	-
18.0(Resistance to insulating material to abnormal heat and fire)	-	2000	-
19.0(Resistance to tracking)	-	2000	-
20.0(Resistance to corrosion)	-	2000	-

15 Jun, 2029

-
Included w.e.f.12.12.2024

IS 1258 (2005)

Bayonet lamp holders (Fourth Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1(Marking )	-	1000	-
8.2(Marking )	-	1000	-
8.3(Marking )	-	1000	-
8.4(Marking )	-	1000	-
8.5(Marking )	-	1000	-
8.6(Marking )	-	1000	-
8.7(Marking )	-	1000	-
8.8(Marking )	-	1000	-
6(Rating )	-	1000	-
6(Rating )	-	1000	-
7(Classification)	-	1000	-
7.2(Classification)	-	1000	-
7.3(Classification)	-	1000	-
7.4(Classification)	-	1000	-
7.5(Classification)	-	1000	-
7.6(Classification)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.2(Dimensions)	-	1000	-
9.3(Dimensions)	-	1000	-
9.3(Dimensions)	-	1000	-
9.3(Dimensions)	-	1000	-
9.3(Dimensions)	-	1000	-
9.3(Dimensions)	-	1000	-
9.3(Dimensions)	-	1000	-
9.3(Dimensions)	-	1000	-
10(Protection against electric shock )	-	1000	-
11.1(Terminals)	-	1000	-
11.2(Terminals)	-	1000	-
11.3(Terminals)	-	1000	-
11.3(Terminals)	-	1000	-
11.3(Terminals)	-	1000	-
11.3(Terminals)	-	1000	-
11.3(Terminals)	-	1000	-
11.3(Terminals)	-	1000	-
11.4(Terminals)	-	1000	-
12(Provision for Earthing)	-	1000	-
13.1(Construction)	-	1000	-
13.1(Construction (Data Sheet No 7005-10))	-	1000	-
13.1(Construction (Data Sheet No 7005-10& 7006-15A))	-	1000	-
13.2(Construction (Data Sheet No 7005-10& 7006-15A))	-	1000	-
13.3(Construction )	-	1000	-
13.4(Construction )	-	1000	-
13.5(Construction)	-	1000	-
13.2 ,13.6 & 13.7 (Construction)	-	1000	-
13.2 ,13.6 & 13.8(Construction)	-	1000	-
13.11(Construction)	-	1000	-
14(Construction)	-	1000	-
15.1(Moisture Resistance, Insulation Resistance and Electric Strength)	-	1000	-
15.2(Moisture Resistance, Insulation Resistance and Electric Strength)	-	1000	-
15.3(Moisture Resistance, Insulation Resistance and Electric Strength)	-	1000	-
16.1(Mechanical Strength)	-	1000	-
16.1(Mechanical Strength)	-	1000	-
16.2(Mechanical Strength)	-	1000	-
16.3(Mechanical Strength)	-	1000	-
16.4(Mechanical Strength)	-	1000	-
16.5(Mechanical Strength)	-	1000	-
16.6 & Table - 6(Mechanical Strength)	-	1000	-
16.7(Mechanical Strength)	-	1000	-
16.8(Mechanical Strength)	-	1000	-
17(Screws,current-carrying parts and connections)	-	1000	-
18(Creepage distances and Clearances)	-	1000	-
18.1, Table 8(Creepage distances and Clearances)	-	1000	-
18.1, Table 8(Creepage distances and Clearances)	-	1000	-
18.1, Table 8(Creepage distances and Clearances)	-	1000	-
18.1, Table 8(Creepage distances and Clearances)	-	1000	-
18.1, Table 8(Creepage distances and Clearances)	-	1000	-
18.1, Table 8(Creepage distances and Clearances)	-	1000	-
18.1, Table 8(Creepage distances and Clearances)	-	1000	-
19.1(General resistance to heat)	-	1000	-
19.2(General resistance to heat)	-	1000	-
19.3(General resistance to heat)	-	1000	-
19.4(Resistance to heat test)	-	1000	-
20.1(Resistance to heat, fire and tracking)	-	1000	-
20.3(Resistance to heat, fire and tracking)	-	1000	-
20.4(Resistance to heat, fire and tracking)	-	1000	-
20.5(Resistance to tracking)	-	1000	-
21.1(Resistance to excessive residual stresses and to rusting)	-	1000	-
21.1(Resistance to excessive residual stresses and to rusting)	-	1000	-
8.1(Marking )	-	1000	-
8.1(Marking )	-	1000	-
8.1(Marking )	-	1000	-
8.1(Marking )	-	1000	-
8.1(Marking )	-	1000	-
8.1(Marking )	-	1000	-
8.1(Marking )	-	1000	-
8.1(Marking )	-	1000	-
8.1(Marking )	-	1000	-
8.1(Marking )	-	1000	-
8.1(Marking )	-	1000	-
8.1(Marking )	-	1000	-
8.1(Marking )	-	1000	-
8.2(Marking )	-	1000	-
8.2(Marking )	-	1000	-
8.2(Marking )	-	1000	-
8.3(Marking )	-	1000	-
8.4(Marking )	-	1000	-
8.5(Marking )	-	1000	-
8.6(Marking )	-	1000	-
8.7(Marking )	-	1000	-
8.8(Marking )	-	1000	-
6(Rating )	-	1000	-
6(Rating )	-	1000	-
7(Classification)	-	1000	-
7.2(Classification)	-	1000	-
7.3(Classification)	-	1000	-
7.4(Classification)	-	1000	-
7.5(Classification)	-	1000	-
7.6(Classification)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.1(Dimensions)	-	1000	-
9.2(Dimensions)	-	1000	-
9.3(Dimensions)	-	1000	-
9.3(Dimensions)	-	1000	-
9.3(Dimensions)	-	1000	-
9.3(Dimensions)	-	1000	-
9.3(Dimensions)	-	1000	-
9.3(Dimensions)	-	1000	-
10(Protection against electric shock )	-	1000	-
11.1(Terminals)	-	1000	-
11.2(Terminals)	-	1000	-
11.3(Terminals)	-	1000	-
12.3(Terminals)	-	1000	-
11.3(Terminals)	-	1000	-
11.3(Terminals)	-	1000	-
11.3(Terminals)	-	1000	-
11.3(Terminals)	-	1000	-
11.4(Terminals)	-	1000	-
12(Provision for Earthing)	-	1000	-
13.1(Construction)	-	1000	-
13.1(Construction (Data Sheet No 7005-10))	-	1000	-
13.1(Construction (Data Sheet No 7005-10& 7006-15A))	-	1000	-
13.2(Construction (Data Sheet No 7005-10& 7006-15A))	-	1000	-
13.3(Construction )	-	1000	-
13.4(Construction )	-	1000	-
13.5(Construction)	-	1000	-
13.2 ,13.6 & 13.7 (Construction)	-	1000	-
13.2 ,13.6 & 13.8(Construction)	-	1000	-
13.11(Construction)	-	1000	-
14(Construction)	-	1000	-
15.1(Moisture Resistance, Insulation Resistance and Electric Strength)	-	1000	-
15.2(Moisture Resistance, Insulation Resistance and Electric Strength)	-	1000	-
15.3(Moisture Resistance, Insulation Resistance and Electric Strength)	-	1000	-
16.1(Mechanical Strength)	-	1000	-
16.1(Mechanical Strength)	-	1000	-
16.2(Mechanical Strength)	-	1000	-
16.3(Mechanical Strength)	-	1000	-
16.4(Mechanical Strength)	-	1000	-
16.5(Mechanical Strength)	-	1000	-
16.6 & Table - 6(Mechanical Strength)	-	1000	-
16.7(Mechanical Strength)	-	1000	-
16.8(Mechanical Strength)	-	1000	-
17(Screws,current-carrying parts and connections)	-	1000	-
18(Creepage distances and Clearances)	-	1000	-
18(Creepage distances and Clearances)	-	1000	-
18(Creepage distances and Clearances)	-	1000	-
18(Creepage distances and Clearances)	-	1000	-
18(Creepage distances and Clearances)	-	1000	-
18(Creepage distances and Clearances)	-	1000	-
18(Creepage distances and Clearances)	-	1000	-
18(Creepage distances and Clearances)	-	1000	-
19.1(General resistance to heat)	-	1000	-
19.2(General resistance to heat)	-	1000	-
19.3(General resistance to heat)	-	1000	-
19.4(Resistance to heat test)	-	1000	-
20.1(Resistance to heat, fire and tracking)	-	1000	-
20.3(Resistance to heat, fire and tracking)	-	1000	-
20.4(Resistance to heat, fire and tracking)	-	1000	-
20.5(Resistance to tracking)	-	1000	-
21.1(Resistance to excessive residual stresses and to rusting)	-	1000	-
21.1(Resistance to excessive residual stresses and to rusting)	-	1000	-

15 Jun, 2029

-
Included w.e.f.12.12.2024

IS 302 : Part 2 : Sec 75 (2018)

Safety of Household and Similar Electrical Appliances Part 2 Particular Requirements Section 75 Commercial Dispensing Appliances and Vending Machines

32500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
32(Radiation, toxicity and similar hazards)	-	500	-
31(Resistance to rusting)	-	500	-
30.2.4(Resistance to heat and fire)	-	500	-
30.2(Resistance to heat and fire)	-	500	-
30.1(Resistance to heat and fire)	-	500	-
29.3(Clearances, creepage distances and solid insulation)	-	500	-
29.2(Clearances, creepage distances and solid insulation)	-	300	-
29.2(Clearances, creepage distances and solid insulation)	-	200	-
29.1, Table No.- 16, Table No.- 17 & Table No.18(Clearances, creepage distances and solid insulation)	-	500	-
29.1, Table No.- 16, Table No.- 17 & Table No.18(Clearances, creepage distances and solid insulation)	-	500	-
28.2 to 28.4(Screws and connections)	-	500	-
28.1, Table No.-14(Screws and connections)	-	500	-
27.6(Provision for earthing)	-	500	-
27.5(Provision for earthing)	-	500	-
27.1 to 27.4(Provision for earthing)	-	500	-
26.10 & 26.11(Terminals for external conductors)	-	500	-
26.9(Terminals for external conductors)	-	500	-
26.1 to 26.8(Terminals for external conductors)	-	300	-
25.16 to 25.25(Supply connection and external flexible cords)	-	200	-
25.15(Supply connection and external flexible cords)	-	300	-
25.14(Supply connection and external flexible cords)	-	200	-
25.9 to 25.13(Supply connection and external flexible cords)	-	500	-
25.8, Table No.-11(Supply connection and external flexible cords)	-	500	-
25.5 to 25.7(Supply connection and external flexible cords)	-	500	-
25.4(Supply connection and external flexible cords)	-	300	-
25.3(Supply connection and external flexible cords)	-	200	-
25.2(Supply connection and external flexible cords)	-	500	-
25.1(Supply connection and external flexible cords)	-	500	-
24.101 to 24.103(Components)	-	500	-
24.2 to 24.6(Components)	-	500	-
24.1(Components)	-	500	-
23.101 to 23.102(Internal wiring)	-	500	-
23.6 to 23.10(Internal wiring)	-	500	-
23.5(Internal wiring)	-	300	-
23.4(Internal wiring)	-	200	-
23.3(Internal wiring)	-	500	-
23.1 & 23.2(Internal wiring)	-	500	-
22.101 to 22.114(Constructions)	-	500	-
22.13 to 22.48(Constructions)	-	500	-
22.12(Constructions)	-	500	-
22.11(Constructions)	-	300	-
22.11(Constructions)	-	200	-
22.7 to 22.10(Constructions)	-	300	-
22.6(Constructions)	-	200	-
22.5(Constructions)	-	300	-
22.4(Constructions)	-	200	-
22.3(Constructions)	-	300	-
22.2(Constructions)	-	200	-
22.1(Constructions)	-	500	-
21.2(MECHANICAL STRENGTH)	-	300	-
21.1(MECHANICAL STRENGTH)	-	200	-
20.2(Stability and mechanical hazards)	-	500	-
20.1(Stability and mechanical hazards)	-	500	-
19.101 and 19.102(ABNORMAL OPERATION)	-	500	-
19.1 to 19.13, Table No. - 9(ABNORMAL OPERATION)	-	500	-
17(Overload protection of transformers and associated circuits)	-	500	-
16.3(Insulation resistance test)	-	500	-
16.3(Electric strength test)	-	500	-
16.1 & 16.2(Leakage current test)	-	500	-
15.102(Moisture resistance)	-	500	-
15.102(Moisture resistance)	-	500	-
15.101(Moisture resistance)	-	500	-
15.3(Moisture resistance)	-	300	-
15.2(Moisture resistance)	-	200	-
15.1(Moisture resistance)	-	500	-
14, Table No.- 6 & Table No.-16(Transient over voltages)	-	500	-
13.3 and Table No.- 4(Electric strength test)	-	300	-
13.1, 13.2(Leakage current test)	-	200	-
11.1 to 11.8, Table No.-3(Heating)	-	500	-
10.1 & 10.2 -Table No. 1, Table No. 2(Power Input and Current)	-	500	-
8.1.5(Protection against access to live parts)	-	500	-
8.1.4(Protection against access to live parts)	-	300	-
8.1.3(Protection against access to live parts)	-	200	-
8.1.2(Protection against access to live parts)	-	500	-
8.1, 8.1.1 & 8.2(Protection against access to live parts)	-	500	-
7.14(Legibility & Durability of Markings test)	-	300	-
7.1 to 7.13, 7.15, 7.16(Marking)	-	200	-
32(Radiation, toxicity and similar hazards)	-	500	-
31(Resistance to rusting)	-	500	-
30.2.4(Resistance to heat and fire)	-	500	-
30.2(Resistance to heat and fire)	-	500	-
30.1(Resistance to heat and fire)	-	500	-
29.3(Clearances, creepage distances and solid insulation)	-	500	-
29.2(Clearances, creepage distances and solid insulation)	-	300	-
29.2(Clearances, creepage distances and solid insulation)	-	200	-
29.1, Table No.- 16, Table No.- 17 & Table No.18(Clearances, creepage distances and solid insulation)	-	500	-
29.1, Table No.- 16, Table No.- 17 & Table No.18(Clearances, creepage distances and solid insulation)	-	500	-
28.2 to 28.4(Screws and connections)	-	500	-
28.1, Table No.-14(Screws and connections)	-	500	-
27.6(Provision for earthing)	-	500	-
27.5(Provision for earthing)	-	500	-
27.1 to 27.4(Provision for earthing)	-	500	-
26.10 & 26.11(Terminals for external conductors)	-	500	-
26.9(Terminals for external conductors)	-	500	-
26.1 to 26.8(Terminals for external conductors)	-	300	-
25.16 to 25.25(Supply connection and external flexible cords)	-	200	-
25.15(Supply connection and external flexible cords)	-	300	-
25.14(Supply connection and external flexible cords)	-	200	-
25.9 to 25.13(Supply connection and external flexible cords)	-	500	-
25.8, Table No.-11(Supply connection and external flexible cords)	-	500	-
25.5 to 25.7(Supply connection and external flexible cords)	-	500	-
25.4(Supply connection and external flexible cords)	-	300	-
25.3(Supply connection and external flexible cords)	-	200	-
25.2(Supply connection and external flexible cords)	-	500	-
25.1(Supply connection and external flexible cords)	-	500	-
24.101 to 24.103(Components)	-	500	-
24.2 to 24.6(Components)	-	500	-
24.1(Components)	-	500	-
23.101 to 23.102(Internal wiring)	-	500	-
23.6 to 23.10(Internal wiring)	-	500	-
23.5(Internal wiring)	-	300	-
23.4(Internal wiring)	-	200	-
23.3(Internal wiring)	-	500	-
23.1 & 23.2(Internal wiring)	-	500	-
22.101 to 22.114(Constructions)	-	500	-
22.13 to 22.48(Constructions)	-	500	-
22.12(Constructions)	-	500	-
22.11(Constructions)	-	300	-
22.11(Constructions)	-	200	-
22.7 to 22.10(Constructions)	-	300	-
22.6(Constructions)	-	200	-
22.5(Constructions)	-	300	-
22.4(Constructions)	-	200	-
22.3(Constructions)	-	300	-
22.2(Constructions)	-	200	-
22.1(Constructions)	-	500	-
21.2(MECHANICAL STRENGTH)	-	300	-
21.1(MECHANICAL STRENGTH)	-	200	-
20.2(Stability and mechanical hazards)	-	500	-
20.1(Stability and mechanical hazards)	-	500	-
19.101 and 19.102(ABNORMAL OPERATION)	-	500	-
19.1 to 19.13, Table No. - 9(ABNORMAL OPERATION)	-	500	-
17(Overload protection of transformers and associated circuits)	-	500	-
16.3(Insulation resistance test)	-	500	-
16.3(Electric strength test)	-	500	-
16.1 & 16.2(Leakage current test)	-	500	-
15.102(Moisture resistance)	-	500	-
15.102(Moisture resistance)	-	500	-
15.101(Moisture resistance)	-	500	-
15.3(Moisture resistance)	-	300	-
15.2(Moisture resistance)	-	200	-
15.1(Moisture resistance)	-	500	-
14, Table No.- 6 & Table No.-16(Transient over voltages)	-	500	-
13.3 and Table No.- 4(Electric strength test)	-	300	-
13.1, 13.2(Leakage current test)	-	200	-
11.1 to 11.8, Table No.-3(Heating)	-	500	-
10.1 & 10.2 -Table No. 1, Table No. 2(Power Input and Current)	-	500	-
8.1.5(Protection against access to live parts)	-	500	-
8.1.4(Protection against access to live parts)	-	300	-
8.1.3(Protection against access to live parts)	-	200	-
8.1.2(Protection against access to live parts)	-	500	-
8.1, 8.1.1 & 8.2(Protection against access to live parts)	-	500	-
7.14(Legibility & Durability of Markings test)	-	300	-
7.1 to 7.13, 7.15, 7.16(Marking)	-	200	-
32(Radiation, toxicity and similar hazards)	-	500	-
31(Resistance to rusting)	-	500	-
30.2.4(Resistance to heat and fire)	-	500	-
30.2(Resistance to heat and fire)	-	500	-
30.1(Resistance to heat and fire)	-	500	-
29.3(Clearances, creepage distances and solid insulation)	-	500	-
29.2(Clearances, creepage distances and solid insulation)	-	300	-
29.2(Clearances, creepage distances and solid insulation)	-	200	-
29.1, Table No.- 16, Table No.- 17 & Table No.18(Clearances, creepage distances and solid insulation)	-	500	-
29.1, Table No.- 16, Table No.- 17 & Table No.18(Clearances, creepage distances and solid insulation)	-	500	-
28.2 to 28.4(Screws and connections)	-	500	-
28.1, Table No.-14(Screws and connections)	-	500	-
27.6(Provision for earthing)	-	500	-
27.5(Provision for earthing)	-	500	-
27.1 to 27.4(Provision for earthing)	-	500	-
26.10 & 26.11(Terminals for external conductors)	-	500	-
26.9(Terminals for external conductors)	-	500	-
26.1 to 26.8(Terminals for external conductors)	-	300	-
25.16 to 25.25(Supply connection and external flexible cords)	-	200	-
25.15(Supply connection and external flexible cords)	-	300	-
25.14(Supply connection and external flexible cords)	-	200	-
25.9 to 25.13(Supply connection and external flexible cords)	-	500	-
25.8, Table No.-11(Supply connection and external flexible cords)	-	500	-
25.5 to 25.7(Supply connection and external flexible cords)	-	500	-
25.4(Supply connection and external flexible cords)	-	300	-
25.3(Supply connection and external flexible cords)	-	200	-
25.2(Supply connection and external flexible cords)	-	500	-
25.1(Supply connection and external flexible cords)	-	500	-
24.101 to 24.103(Components)	-	500	-
24.2 to 24.6(Components)	-	500	-
24.1(Components)	-	500	-
23.101 to 23.102(Internal wiring)	-	500	-
23.6 to 23.10(Internal wiring)	-	500	-
23.5(Internal wiring)	-	300	-
23.4(Internal wiring)	-	200	-
23.3(Internal wiring)	-	500	-
23.1 & 23.2(Internal wiring)	-	500	-
22.101 to 22.114(Constructions)	-	500	-
22.13 to 22.48(Constructions)	-	500	-
22.12(Constructions)	-	500	-
22.11(Constructions)	-	300	-
22.11(Constructions)	-	200	-
22.7 to 22.10(Constructions)	-	300	-
22.6(Constructions)	-	200	-
22.5(Constructions)	-	300	-
22.4(Constructions)	-	200	-
22.3(Constructions)	-	300	-
22.2(Constructions)	-	200	-
22.1(Constructions)	-	500	-
21.2(MECHANICAL STRENGTH)	-	300	-
21.1(MECHANICAL STRENGTH)	-	200	-
20.2(Stability and mechanical hazards)	-	500	-
20.1(Stability and mechanical hazards)	-	500	-
19.101 and 19.102(ABNORMAL OPERATION)	-	500	-
19.1 to 19.13, Table No. - 9(ABNORMAL OPERATION)	-	500	-
17(Overload protection of transformers and associated circuits)	-	500	-
16.3(Insulation resistance test)	-	500	-
16.3(Electric strength test)	-	500	-
16.1 & 16.2(Leakage current test)	-	500	-
15.102(Moisture resistance)	-	500	-
15.102(Moisture resistance)	-	500	-
15.101(Moisture resistance)	-	500	-
15.3(Moisture resistance)	-	300	-
15.2(Moisture resistance)	-	200	-
15.1(Moisture resistance)	-	500	-
14, Table No.- 6 & Table No.-16(Transient over voltages)	-	500	-
13.3 and Table No.- 4(Electric strength test)	-	300	-
13.1, 13.2(Leakage current test)	-	200	-
11.1 to 11.8, Table No.-3(Heating)	-	500	-
10.1 & 10.2 -Table No. 1, Table No. 2(Power Input and Current)	-	500	-
8.1.5(Protection against access to live parts)	-	500	-
8.1.4(Protection against access to live parts)	-	300	-
8.1.3(Protection against access to live parts)	-	200	-
8.1.2(Protection against access to live parts)	-	500	-
8.1, 8.1.1 & 8.2(Protection against access to live parts)	-	500	-
7.14(Legibility & Durability of Markings test)	-	300	-
7.1 to 7.13, 7.15, 7.16(Marking)	-	200	-
32(Radiation, toxicity and similar hazards)	-	500	-
31(Resistance to rusting)	-	500	-
30.2.4(Resistance to heat and fire)	-	500	-
30.2(Resistance to heat and fire)	-	500	-
30.1(Resistance to heat and fire)	-	500	-
29.3(Clearances, creepage distances and solid insulation)	-	500	-
29.2(Clearances, creepage distances and solid insulation)	-	300	-
29.2(Clearances, creepage distances and solid insulation)	-	200	-
29.1, Table No.- 16, Table No.- 17 & Table No.18(Clearances, creepage distances and solid insulation)	-	500	-
29.1, Table No.- 16, Table No.- 17 & Table No.18(Clearances, creepage distances and solid insulation)	-	500	-
28.2 to 28.4(Screws and connections)	-	500	-
28.1, Table No.-14(Screws and connections)	-	500	-
27.6(Provision for earthing)	-	500	-
27.5(Provision for earthing)	-	500	-
27.1 to 27.4(Provision for earthing)	-	500	-
26.10 & 26.11(Terminals for external conductors)	-	500	-
26.9(Terminals for external conductors)	-	500	-
26.1 to 26.8(Terminals for external conductors)	-	300	-
25.16 to 25.25(Supply connection and external flexible cords)	-	200	-
25.15(Supply connection and external flexible cords)	-	300	-
25.14(Supply connection and external flexible cords)	-	200	-
25.9 to 25.13(Supply connection and external flexible cords)	-	500	-
25.8, Table No.-11(Supply connection and external flexible cords)	-	500	-
25.5 to 25.7(Supply connection and external flexible cords)	-	500	-
25.4(Supply connection and external flexible cords)	-	300	-
25.3(Supply connection and external flexible cords)	-	200	-
25.2(Supply connection and external flexible cords)	-	500	-
25.1(Supply connection and external flexible cords)	-	500	-
24.101 to 24.103(Components)	-	500	-
24.2 to 24.6(Components)	-	500	-
24.1(Components)	-	500	-
23.101 to 23.102(Internal wiring)	-	500	-
23.6 to 23.10(Internal wiring)	-	500	-
23.5(Internal wiring)	-	300	-
23.4(Internal wiring)	-	200	-
23.3(Internal wiring)	-	500	-
23.1 & 23.2(Internal wiring)	-	500	-
22.101 to 22.114(Constructions)	-	500	-
22.13 to 22.48(Constructions)	-	500	-
22.12(Constructions)	-	500	-
22.11(Constructions)	-	300	-
22.11(Constructions)	-	200	-
22.7 to 22.10(Constructions)	-	300	-
22.6(Constructions)	-	200	-
22.5(Constructions)	-	300	-
22.4(Constructions)	-	200	-
22.3(Constructions)	-	300	-
22.2(Constructions)	-	200	-
22.1(Constructions)	-	500	-
21.2(MECHANICAL STRENGTH)	-	300	-
21.1(MECHANICAL STRENGTH)	-	200	-
20.2(Stability and mechanical hazards)	-	500	-
20.1(Stability and mechanical hazards)	-	500	-
19.101 and 19.102(ABNORMAL OPERATION)	-	500	-
19.1 to 19.13, Table No. - 9(ABNORMAL OPERATION)	-	500	-
17(Overload protection of transformers and associated circuits)	-	500	-
16.3(Insulation resistance test)	-	500	-
16.3(Electric strength test)	-	500	-
16.1 & 16.2(Leakage current test)	-	500	-
15.102(Moisture resistance)	-	500	-
15.102(Moisture resistance)	-	500	-
15.101(Moisture resistance)	-	500	-
15.3(Moisture resistance)	-	300	-
15.2(Moisture resistance)	-	200	-
15.1(Moisture resistance)	-	500	-
14, Table No.- 6 & Table No.-16(Transient over voltages)	-	500	-
13.3 and Table No.- 4(Electric strength test)	-	300	-
13.1, 13.2(Leakage current test)	-	200	-
11.1 to 11.8, Table No.-3(Heating)	-	500	-
10.1 & 10.2 -Table No. 1, Table No. 2(Power Input and Current)	-	500	-
8.1.5(Protection against access to live parts)	-	500	-
8.1.4(Protection against access to live parts)	-	300	-
8.1.3(Protection against access to live parts)	-	200	-
8.1.2(Protection against access to live parts)	-	500	-
8.1, 8.1.1 & 8.2(Protection against access to live parts)	-	500	-
7.14(Legibility & Durability of Markings test)	-	300	-
7.1 to 7.13, 7.15, 7.16(Marking)	-	200	-
19.11.4.4(Surge immunity test)	-	500	-
19.11.4.7(Harmonics)	-	500	-

15 Jun, 2029

-
Included w.e.f.11.12.2024 Exclusion CL 19.11.4.1 (Electrostatic discharges) CL 19.11.4.2 (Radiated fields) CL 19.11.4.3 (Fast transient bursts) CL 19.11.4.5 (Immunity to conducted discharges) CL 19.11.4.6 (Class 3 Voltage dips and interruptions)

IS 302 : Part 2 : SEC 31 (2009)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 31 range hoods

50000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause No - 5(GENERAL CONDITIONS FOR THE TESTS)	-	2000	-
Clause No - 5.18(linear and angular dimension)	-	2000	-
Clause No - 6.2(harmfull ingress of water)	-	2000	-
Clause No - 8.1.1("PROTECTION AGAINST ACCESS TO LIVE PART- test probe B")	-	2000	-
Clause No - 8.1.2("PROTECTION AGAINST ACCESS TO LIVE PART - test probe 13")	-	2000	-
Clause No - 8.2(Addition)	-	2000	-
Clause No - 10.1, Table No. -1(power input deviation)	-	2000	-
Clause No - 13.3("LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING TEMPERATURE")	-	2000	-
Clause No - 13.3,Table No.- 4(voltage for electrical strength)	-	2000	-
Clause No - 14(Impulse test voltage)	-	2000	-
Clause No - 15.1.1(MOISTURE RESISTANCE)	-	2000	-
Clause No -19.7(test is repeated with the capacitor short circuited)	-	2000	-
Clause No -21.1(Mechanical strength)	-	2000	-
Clause No -22.1(construction)	-	2000	-
Clause No -22.11(push force applied)	-	2000	-
Clause No -24.1.2(safety isolating transformer)	-	2000	-
Clause No -24.1.3(for switches)	-	2000	-
Clause No -24.1.4(for automatic control)	-	2000	-
Clause No -24.1.5(for innterconnection couplers)	-	2000	-
Clause No -25.8, Table no -11(conductor resistance)	-	2000	-
Clause No -25.5(dimension for pins)	-	2000	-
Clause No -27.6(for circuit board)	-	2000	-
Clause No -29.2(comparative tracking index)	-	2000	-
Clause No -29.3.3(dry heat test)	-	2000	-
Clause No -30.2.1(glow wire test)	-	2000	-
Clause No -30.101("incorporate combustible material")	-	2000	-
Clause No -24.4(plug and socket)	-	2000	-

15 Jun, 2029

-
Exclusion: Clause No -19.11.4.1 (electrostatic discharge) Clause No -19.11.4.2 (radiated field) Clause No -19.11.4.3 (fast transient) Clause No -19.11.4.4 (Voltage dips and interruption)

IS 302 : Part 2 : Sec 23 (2009)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 23 appliances for skin or hair care (First Revision)

50000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
32(Radiation ,Toxicity and similar hazards)	-	1500	-
31(Resistance to Rusting)	-	1500	-
30(Resistance to Heat & Fire)	-	1500	-
29(Clearances, Creepage Distances & Solid Insulation)	-	1500	-
28(Screws & Connection)	-	1500	-
27(Provision For Earthing)	-	1500	-
26(Terminals For External Conductors)	-	1500	-
25(Supply Connection & External Flexible Cables and Cords)	-	1500	-
24(Component)	-	1500	-
23(Internal wiring)	-	1500	-
22(Construction)	-	1500	-
21(Mechanical strength)	-	1500	-
20(Stability & Mechanical Hazards)	-	1500	-
19(Abnormal Operation)	-	1500	-
18(Endurance)	-	1500	-
17(Overload Protection/ Overload Protection of Transformers & Associated Circuits)	-	1500	-
16(Leakage Current and Electric Strength)	-	1500	-
15(Moisture Resistance)	-	1500	-
14(Transient Over Voltage)	-	1500	-
13(Leakage Current and Electric Strength at Operating Temperature)	-	1500	-
11(Temperature Rise/Heating)	-	1500	-
10(Power Input & Current)	-	1500	-
9(Starting Of Motor Operated Appliances)	-	1500	-
8(Protection against Electric Shock/ Protection against Access to Live Parts)	-	1500	-
7(Marking/ Marking & Instructions)	-	1500	-
6(Classification)	-	1500	-
22.32(CONSTRUCTION)	-	1500	-
19.11.4.4(Surge immunity test)	-	1500	-
19.11.4.7(Harmonics)	-	1500	-
32(Radiation ,Toxicity and similar hazards)	-	1500	-
31(Resistance to Rusting)	-	1500	-
30(Resistance to Heat & Fire)	-	1500	-
29(Clearances, Creepage Distances & Solid Insulation)	-	1500	-
28(Screws & Connection)	-	1500	-
27(Provision For Earthing)	-	1500	-
26(Terminals For External Conductors)	-	1500	-
25(Supply Connection & External Flexible Cables and Cords)	-	1500	-
24(Component)	-	1500	-
23(Internal wiring)	-	1500	-
22(Construction)	-	1500	-
21(Mechanical strength)	-	1500	-
20(Stability & Mechanical Hazards)	-	1500	-
19(Abnormal Operation)	-	1500	-
18(Endurance)	-	1500	-
17(Overload Protection/ Overload Protection of Transformers & Associated Circuits)	-	1500	-
16(Leakage Current and Electric Strength)	-	1500	-
15(Moisture Resistance)	-	1500	-
14(Transient Over Voltage)	-	1500	-
13(Leakage Current and Electric Strength at Operating Temperature)	-	1500	-
11(Temperature Rise/Heating)	-	1500	-
10(Power Input & Current)	-	1500	-
9(Starting Of Motor Operated Appliances)	-	1500	-
8(Protection against Electric Shock/ Protection against Access to Live Parts)	-	1500	-
7(Marking/ Marking & Instructions)	-	1500	-
6(Classification)	-	1500	-
22.32(CONSTRUCTION)	-	1500	-
19.11.4.4(Surge immunity test)	-	1500	-
19.11.4.7(Harmonics)	-	1500	-

15 Jun, 2029

-
Included w.e.f. 18.09.2024 Exclusion: Cl.19.11.4.1 (Electrostatic discharges) Cl.19.11.4.2 (Radiated fields) Cl.19.11.4.3 (Fast transient bursts) Cl.19.11.4.5 (Immunity to conducted discharges) Cl.19.11.4.6 (Class 3 Voltage dips and interruptions)

First
Prev
1
2
3
4
Next
Last

Bureau of Indian Standards

The National Standards Body of India

(Suspended)ATCC TEST LABS LLP

KHASRA NO. 45/6, SITUATED IN THE AREA, VILLAGE PRAHLADPUR BANGER,, North West Delhi, Delhi, 110042, Delhi, North West, Delhi, 110042

9891606632 info@atcctestlabs.com

Scope List