BIS - LIMS (Laboratory Information Management System)

Search by IS Number

Reset

14051 Results

S.No.

Lab Name

Osl Code

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

4291

Kailtech Test and Research Centre Pvt. Ltd., Indore

8125636

IS 7834 : Part 8 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 8 Specific requirements for caps

8051.16 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.2.2(diameter of the socket of cap)	-	0		No Test required
6.1.1(VCM Content Test)	-	10000		OK

18 Dec, 2027

-
-

4292

Kailtech Test and Research Centre Pvt. Ltd., Indore

8125636

IS 8041 (1990)

Rapid hardening portland cement - Specific4tion (Second Revision)

All

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1 - Table - 1 i(Ratio of percentage of lime to percentages of silica, alumina and iron oxide - Cl 4 of IS 4032:1985)	-	3000	atio of percentage of lime to percentages of silica, alumina and iron oxide
5.1 - Table - 1 ii(Ratio of percentage of alumina to that of iron oxide - Cl 4 of IS 4032:1985)	-	2000	Ratio of percentage of alumina to that of iron oxide
5.1 - Table - 1 iii(Insoluble residue - Cl 4.10 of IS 4032:1985)	-	1500	Insoluble residue
5.1 - Table - 1 iv(Magnesia - Cl 4.8 of IS 4032:1985)	-	1000	Magnesia
5.1 - Table - 1 v(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-	1000	Total Sulphur Content calculated as Sulphuric Anhydride (SO3)
5.1 - Table - 1 vi(Total loss on ignition - Cl 4.2 of IS 4032:1985)	-	1000	Total loss on ignition
6.1(Fineness 4031 Part 2)	-	1000	Fineness
6.2.1(Expansion by Le Chatelier- 4031 Part 3)	-	1000	Expansion by Le Chatelier
6.2.1(Expansion by Autoclave- 4031 Part 3)	-	3000	Expansion by Autoclave
6.3 a)(Setting Time Initial- 4031 Part 5)	-	2000	Setting Time Initial & Final
6.3 b)(Setting Time Final- 4031 Part 5)	-	2000	Setting Time Initial & Final
6.4 a)(Compressive Strength At 24 hrs ± 30 minutes - IS 4031 Part 6)	-	5000	Compressive Strength (All Ages)
6.4 b)(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	5000	Compressive Strength (All Ages)
6.5(Transverse Strength - IS 4031 Part 8 (Optional))	-	5000	Compressive Strength (All Ages)

18 Dec, 2027

-
-

4293

Kailtech Test and Research Centre Pvt. Ltd., Indore

8125636

IS 7887 (1992)

Mild steel wire rod for general engineering purposes - Specification (First Revision)

All

7320 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8(Workmanship)	-	1000	NA
Cl 9(Nominal Diameter & Out Of Shape)	-	1000	Dimensions
6.1(Carbon %)	-	500	Carbon
6.1(Manganese %)	-	500	Manganese
6.1(Phosphorus %)	-	500	Phosphorous
6.1(Sulphur %)	-	500	Sulphur
6.1(Silicon %)	-	500	Silicon
6.1( Aluminium %)	-	500	Aluminium
Cl. 9(Out of Shape)	-	1000	Dimension

18 Dec, 2027

-
-

4294

Kailtech Test and Research Centre Pvt. Ltd., Indore

8125636

IS 13487 (1992)

Irrigation equipment - Emitters - Specification

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.2(Flow path in emitters)	-	2000	OK
7.3.1(Resistance to Hydrostatic pressure)	-	3000	OK
7.3.2(Resistance to Hydrostatic pressure)	-	3000	OK
7.3.3(Resistance to Hydrostatic pressure)	-	3000	OK
7.4.1(Emitter Pull Out In-line emitters)	-	2000	OK
8.1.2(Uniformity of Emission Rate Unregulated emitters)	-	2000	OK
8.1.2(Uniformity of Emission Rate Unregulated emitters)	-	2000	OK
8.1.3(Uniformity of Emission Rate Regulated emitters)	-	2000	OK
8.2.2(Emission rate as a function of inlet pressure Unregulated emitters)	-	2000	OK
8.2.3(Emission rate as a function of inlet pressure Regulated emitters)	-	2000	OK
8.3(Determination of Emitter Exponent)	-	5000	OK

18 Dec, 2027

-
-

4295

Kailtech Test and Research Centre Pvt. Ltd., Indore

8125636

IS 13757 (1993)

Burnt Clay Fly Ash Building Bricks-specification

All

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.0(GENERAL QUALITY)	-	1000	General Requirement
6.1(Dimensions)	-	2000	All Dimensions and Tolerance
6.2(Tolerances)	-	2000	All Dimensions and Tolerance
7.1(Compressive Strength)	-	4000	Compressive Strength
7.3(Efforescence)	-	1500	Efflorescence

18 Dec, 2027

-
-

4296

Kailtech Test and Research Centre Pvt. Ltd., Indore

8125636

IS 6527 (1995)

Stainless steel wire rods - Specification (First Revision)

All

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 9(Tensile & Hardness)	-	8500	Tensile and Hardness
Cl 10(Diameter & Out Of Round)	-	500	Dimension
Cl. 10.1(Out of Round)	-	500	Dimension
Cl. 6(Freedom from defects)	-	500	Freedom from Defects
Cl. 9 .1 Table 3(0.2 % Proof Stress )	-	7500	0.2 % Proof Stress
Cl. 9 .1 Table 3(Elongation)	-	7500	Elongation
Cl. 9.2 Table 4(Hardness)	-	1000	Hardness

18 Dec, 2027

-
-

4297

Kailtech Test and Research Centre Pvt. Ltd., Indore

8125636

IS 6528 (1995)

Stainless steel wire - Specification (First Revision)

All

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Table 7(Workmanship)	-	14250	Chemical Composition
Cl 6(Workmanship)	-	1000	Freedom from Defects
Cl 9.1 & Table 3(Diameter & Out Of Round)	-	1000	Dimensions
Cl 10(UTM)	-	7500	Tensile Test

18 Dec, 2027

-
-

4298

Kailtech Test and Research Centre Pvt. Ltd., Indore

8125636

IS 3975 (1999)

Low carbon galvanized steel wires, formed wires and tapes for armouring of cables - Specification (Third Revision)

All

4050 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Dimensions)	-	1000	NA
11(Freedom from defects)	-	1000	Freedom from Defects
9.1(Galvanizing Requirements )	-	1000	Mass of Coating
9.2(Galvanizing Requirements )	-	1000	Uniformity of Coating
9.3(Galvanizing Requirements )	-	2000	Adhesion Test
8.1(Mechanical Properties (as per table 5 of IS 1608))	-	3000	Tensile
8.2(Mechanical Properties (as per IS 1717))	-	2000	Torsion
8.3(Mechanical Properties (as per IS 1755))	-	2000	Wrapping
8.4(Mechanical Properties (as per IS 10810(Part- 42)))	-	2000	Resistance Test
7(Dimensions)	-	1000	Dimension
8.1(Mechanical Properties (as per table 5 of IS 1608))	-	3000	Elongation

18 Dec, 2027

-
-

4299

Kailtech Test and Research Centre Pvt. Ltd., Indore

8125636

IS 9103 (1999)

Specification for Concrete Admixtures -

All

35000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4, Table 1A(Slump)	-	3000	Slump
Cl 4, Table 1 B(Flow)	-	5000	Flow
Cl 4, Table 1 B(Loss of workability on standing)	-	5000	Loss of Workability on Standing
Cl 4, Table 1 B(Minimum compressive strength ( 7 Days,28 Days, 6 Month and 1 Year))	-	5000	Time of setting, allowable deviation from control sample hours
Cl 4, Table 1A(Water Content, percent of control sample, Max)	-	5000	Time of setting, allowable deviation from control sample hours
Cl 4, Table 1A(Time of setting, allowable deviation from control sample hours)	-	5000	Time of setting, allowable deviation from control sample hours
Cl 4, Table 1A(Compressive strength, percent of control sample, Min)	-	5000	Compressive strength, percent of control sample
Cl 4, Table 1A(Flexural strength, percent of control sample, Min)	-	5000	Flexural strength, percent of control sample
Cl 4, Table 1A(Length change, percent increase over control sample, Max)	-	5000	Length change, percent increase over control sample
Cl 4, Table 1A(Bleeding, percent increase over control sample, Max)	-	5000	Bleeding, percent increase over control sample
Cl 4, Table 1A(Air content (%), Max, over control)	-	5000	Air content (%), Max, over control
Clause 9, Table- 2( pH)	-	750	pH
Clause 9, Table- 2(Dry material content )	-	1000	Dry Material Content
Clause 9, Table- 2(Ash content)	-	750	Ash Content
Clause 9, Table- 2(Relative density)	-	750	Relative Density
Clause 9, Table- 2(Chloride ion content)	-	1500	Chloride Content
4, Table 1B( minimum Compressive strength percent of control mix concrete 7 days)	-	-	-
Clause 4, Table 1A, SI no. (iii) (Initial time of setting allowable deviation from control sample)	-	-	-
4, Table 1A(Compressive strength percent of control Sample 1 Day )	-	-	-
4, Table 1A(Flexural strength percent of control Sample 3 Day)	-	-	-
4, Table 1A(Length Change percent Increase over control Sample 28 Day)	-	-	-
4, Table 1B( minimum Compressive strength percent of control mix concrete 28 days)	-	-	-
4, Table 1B( minimum Compressive strength percent of control mix concrete 6 Months days)	-	-	-
4, Table 1B( minimum Compressive strength percent of control mix concrete 1 Year )	-	-	-
Clause 4, Table 1A, SI no. (iii) (Final time of setting allowable deviation from control sample)	-	-	-
4, Table 1A(Compressive strength percent of control Sample 3 Days)	-	-	-
4, Table 1A(Compressive strength percent of control Sample 7 Days)	-	-	-
4, Table 1A(Compressive strength percent of control Sample 28 Days )	-	-	-
4, Table 1A(Compressive strength percent of control Sample 6 Months )	-	-	-
4, Table 1A(Compressive strength percent of control Sample 1 year )	-	-	-
4, Table 1A(Flexural strength percent of control Sample 7 Day)	-	-	-
4, Table 1A(Flexural strength percent of control Sample 28 Day)	-	-	-
4, Table 1A(Length Change percent Increase over control Sample 6 Month)	-	-	-
4, Table 1A(Length Change percent Increase over control Sample 1 year)	-	-	-

18 Dec, 2027

-
-

4300

Kailtech Test and Research Centre Pvt. Ltd., Indore

8125636

IS 1786 (2008)

High strength deformed steel bars and wires for concretere inforcement - Specification (Fourth Revision)

All

21000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 9.4(Load In Other Direction From Bend)	-	2000	None
Cl 9.3(Load In One Direction)	-	1000	None
Cl 8.1(UTM)	-	3000	None
Cl 7.2(Weight)	-	750	None
Cl 6.1(Length, Width & Thickness)	-	750	None
Cl 5(Deformations and Surface Characteristics)	-	10000	Deformations and Surface Characteristics (Pull Out Test)
4.1(Carbon %)	-	500	Carbon
4.1(Manganese %)	-	500	Manganese
4.1(Sulphur %)	-	500	Sulphur
4.1(Phosphorus %)	-	500	Phosphorous
4.1( Nitrogen%)	-	1500	Nitrogen
4.1(Silicon %)	-	500	Silicon
4.1(Ni)	-	1500	Nickle
4.1(Cr)	-	750	Chromium
4.1(Mo)	-	750	Molybdenum
4.1( Copper %)	-	750	Copper
4.1(V)	-	1500	Vanadium
4.1( Ti)	-	1500	Titanium
4.1( Nb)	-	1500	Niobium
4.1( Aluminium %)	-	500	Aluminium
4.1(Sulphur and phosphorous)	-	500	Sulphur and Phosphorous
4.1(CE)	-	500	Carbon Equivalent
Cl.9.4 & Cl. 9.4.1(Rebend test)	-	2000	Rebend Test
Cl. 9.3, Table 4(Bend Test )	-	1000	Bend Test
Cl. 8.1 Table 3(Tensile Strength (TS))	-	3000	Tensile Test
Cl. 7.2 Table -2 (Nominal Mass)	-	750	Nominal Mass
Cl. 6.1(Nominal Size)	-	750	Nominal Size (Specified Length)
Cl 5(Deformations and Surface Characteristics)	-	500	TS /YS Ratio
Cl. 5 (Cl.5 Mean area of ribs/unit length (Ar), )	-	1000	Mean area of ribs/unit length
Cl. 5 (Cl. 5 - Mean projected area of transverse ribs (1/3 of Ar))	-	1000	Mean projected area of transverse ribs
Cl. 8.1 Table 3(Yield Stress (YS))	-	3000	Yield Stress
Cl. 8.1 Table 3(Elongation, percentage)	-	3000	Elongation
Cl 6.1(Length, Width & Thickness)	-	3000	Maximum Extension
Cl 8.1(UTM)	-	3000	Elongation at maximum Force
Cl 7.2(Weight)	-	1000	Ribs Contributing to Projected Area
Cl 9.4(Load In Other Direction From Bend)	-	1000	Gross Cross Sectional Area
Cl 9.3(Load In One Direction)	-	1000	Visual Inspection
Cl. 4.3(Visual Inspection.)	-	1000	Visual Inspection
5.7(PullOut (Bond Test))	-	5000	Pull Out
8.18.1 Table 3(Total elongation at maximum force)	-	3000	Total elongation at maximum force
Cl. 8.1 Table 3(Maximum Extension)	-	3000	Maximum Extension
Cl. 5.2(Surface Characteristics)	-	1000	Surface Characteristics
Cl. 6.2, 6.3 Table 1(Gross Cross Sectional Area, A)	-	750	Gross Cross Sectional Area
Cl. 5.3 (a)(The ribs contributing the projected area - Longitudinal Ribs)	-	1000	The ribs contributing the projected area - Longitudinal Ribs
Cl. 5.3 (b)(The ribs contributing the projected area - Transverse Ribs)	-	1000	The ribs contributing the projected area - Transverse Ribs
Cl. 8.1 Table 3(TS/YS Ratio)	-	1000	TS/YS Ratio
Cl. 5.7(Date of casting of concrete cubes)	-	1000	Date of casting of concrete cubes
Cl. 5.7(Date of testing of concrete cubes)	-	1000	Date of testing of concrete cubes
Cl. 5.7(Average compressive strength of cubes at 28 days)	-	1000	Average compressive strength of cubes at 28 days
Cl. 5.7(Bond Strength at 0.25 mm slip)	-	5000	Bond Strength at 0.25 mm slip

18 Dec, 2027

-
-

4301

Bharat Test House Pvt. Ltd. 1668 Sonipat

9168306

IS 2202 : Part 1 (2023)

WOODEN FLUSH DOOR SHUTTERS SOLID CORE TYPE SPECIFICATION PART 1 PLYWOOD FACE PANELS Seventh Revision

Wooden Flush Door Shutters (Solid Core Type)-Specification

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.1(Workmanship & Finish)	-	200	-
9.2(Workmanship & Finish)	-	100	-
9.3(Workmanship & Finish)	-	100	-
11.1(Dimensions - Height)	-	200	-
11.1(Dimensions - Width)	-	100	-
11.1(Dimensions - Thickness)	-	100	-
11.1(Dimensions - Variation in thickness)	-	100	-
11.1(Dimensions - Squareness)	-	100	-
11.12(End immersion test)	-	500	-
11.13(Knife Test)	-	300	-
11.14(Glue Adhesion Test)	-	500	-
4(GRADE)	-	200	-
4(TYPE)	-	100	-
5(SIZES)	-	300	-
7.1.1(CONSTRUCTION-Blockboard Core)	-	200	-
7.1.1(CONSTRUCTION-Blockboard Core)	-	100	-
7.1.2(CONSTRUCTION-Blockboard Core)	-	100	-
7.3.2(CONSTRUCTION-Stiles and Rails)	-	200	-
7.3.2(a)(CONSTRUCTION-Stiles and Rails-Joints)	-	100	-
7.3.2(b)(CONSTRUCTION-Stiles and Rails-Joints)	-	100	-
7.3.2(c)(CONSTRUCTION-Stiles and Rails-Joints)	-	100	-
7.3.3(CONSTRUCTION-Stiles and Rails)	-	100	-
9.1(WORKMANSHIP AND FINISH)	-	100	-
9.2(WORKMANSHIP AND FINISH)	-	100	-
9.3(WORKMANSHIP AND FINISH)	-	100	-
11.1(Dimensions and Squareness Test)	-	200	-
11.1(Dimensions and Squareness Test)	-	200	-
11.1(Dimensions and Squareness Test)	-	200	-
11.1(Dimensions and Squareness Test)	-	200	-
11.1(Dimensions and Squareness Test)	-	200	-
11.2(General Flatness Test)	-	200	-
11.2(General Flatness Test)	-	200	-
11.2(General Flatness Test)	-	200	-
11.3(Local Planeness Test)	-	200	-
11.4(Impact Indentation Test)	-	200	-
11.4(Impact Indentation Test)	-	500	-
11.5(Flexure Test)	-	200	-
11.5(Flexure Test)	-	500	-
11.6(Edge Loading Test)	-	200	-
11.6(Edge Loading Test)	-	200	-
11.6(Edge Loading Test)	-	200	-
11.6(Edge Loading Test)	-	200	-
11.7.1(Shock Resistance Test)	-	500	-
11.7.2(Shock Resistance Test)	-	200	-
11.8(Buckling Test)	-	300	-
11.8(Buckling Test)	-	300	-
11.8(Buckling Test)	-	300	-
11.9.2(Slamming Test)	-	200	-
11.9.3(Slamming Test)	-	200	-
11.10(Misuse Test)	-	200	-
11.11(Varying Humidity Test)	-	300	-
11.11(Varying Humidity Test)	-	300	-
11.12(End Immersion Test)	-	300	-
11.13(Knife Test)	-	300	-
11.14(Glue Adhesion Test)	-	300	-
11.15(Screw Withdrawal Resistance Test)	-	200	-
11.15(Screw Withdrawal Resistance Test)	-	200	-
Clause 4.2(grades specified)	-	200	-
Clause 5(SIZES)	-	200	-
Clause 6.1.1(species of timber)	-	500	-
Clause 6.1.2(list of species)	-	200	-
Clause 6.1.3(moisture content)	-	200	-
Clause 6.2.1(Plywood)	-	500	-
Clause 6.2.2(Decorative plywood)	-	200	-
Clause 6.3(Cross-Bands)	-	500	-
Clause 6.4.1(Commercial Face Veneers)	-	500	-
Clause 6.4.2(Decorative Face Veneers)	-	200	-
Clause 6.6.1(Adhesives)	-	500	-
Clause 6.7(Particle Board)	-	500	-
Clause 6.8(Medium density fibre board)	-	500	-
Clause 6.9(Alternative Materials)	-	200	-
Clause 7.1(Blockboard Core)	-	200	-
Clause 7.2(Particle Board or Medium Density Fibre)	-	200	-
Clause 7.3(Stiles and Rails)	-	200	-
Clause 7.4(Levelling)	-	200	-
Clause 7.5(Face Panel)	-	200	-
Clause 7.6(Lipping)	-	200	-
Clause 7.7(Rebating)	-	200	-
Clause 7.8(Opening for Glazing)	-	200	-
Clause 7.9(Venetian)	-	500	-
Clause 8.1(Locks)	-	200	-
Clause 9(WORKMANSHIP AND FINISH)	-	200	-
Clause 10.1(Classification of Tests)	-	200	-
Clause 11.1(Dimensions and Squareness Test)	-	200	-
Clause 11.2(General Flatness Test)	-	200	-
Clause 11.3(Local Planeness Test)	-	200	-
Clause 11.4(Impact Indentation Test)	-	200	-
Clause 11.5(Flexure Test)	-	200	-
Clause 11.6(Edge Loading Test)	-	200	-
Clause 11.7(Shock Resistance Test)	-	200	-
Clause 11.8(Buckling Resistance Test)	-	200	-
Clause 11.9(Slamming Test)	-	200	-
Clause 11.10(Misuse Test)	-	200	-
Clause 11.11(Varying Humidity Test)	-	200	-
Clause 11.12(End Immersion Test)	-	200	-
Clause 11.13(Knife Test)	-	200	-
Clause 11.14(Glue Adhesion Test)	-	200	-
Clause 11.15(Screw Withdrawal Resistance Test)	-	200	-
Clause 12(SAMPLING AND CRITERIA FOR CONFORMITY)	-	200	-
Clause 13(ADDITIONAL REQUIREMENTS FOR ECO MARK)	-	200	-
Clause 14(Marking)	-	200	-
4(Grade, Type and Construction)	-	200	-
5(Sizes and Thickness)	-	200	-
6.1(Timber)	-	200	-
6.2(Plywood for flush door shutter)	-	200	-
6.3(Cross-Bands )	-	200	-
6.4.1(Commercial Face Veneers)	-	200	-
6.4.2(Decorative face veneers)	-	200	-
6.6(Adhesives)	-	200	-
6.7(Particle Board)	-	200	-
6.8(Medium Density Fibre)	-	200	-
6.9(Alternative Materials)	-	200	-
7(Construction)	-	200	-
8.1(Locks)	-	200	-
8.2(Other Fittings)	-	200	-
9(Workmanship and Finish)	-	200	-
10(Tests)	-	200	-
11.1(Dimensions and Squareness Test)	-	200	-
11.2(General Flatness Test)	-	200	-
11.3(Local Planeness Test)	-	200	-
11.4(Impact Indentation Test)	-	200	-
11.5(Flexure Test)	-	200	-
11.6(Edge Loading Test)	-	200	-
11.7(Shock Resistance Test)	-	200	-
11.8(Buckling Resistance Test)	-	200	-
11.9(Slamming Test)	-	200	-
11.1(Misuse Test)	-	200	-
11.11(Varying Humidity Test)	-	200	-
11.12(End Immersion Test)	-	200	-
11.13(Knife Test)	-	200	-
11.14(Glue Adhesion Test)	-	200	-
11.15(Screw Withdrawal Resistance Test)	-	200	-
14(Marking )	-	200	-
Cl-13(ADDITIONAL REQUIREMENTS FOR ECO MARK)	-	200	-
9.1(Workmanship & Finish)	-	0	-
9.2(Workmanship & Finish)	-	0	-
9.3(Workmanship & Finish)	-	0	-
11.1(Dimensions - Height)	-	0	-
11.1(Dimensions - Width)	-	0	-
11.1(Dimensions - Thickness)	-	0	-
11.1(Dimensions - Variation in thickness)	-	0	-
11.1(Dimensions - Squareness)	-	0	-
11.12(End immersion test)	-	0	-
11.13(Knife Test)	-	0	-
11.14(Glue Adhesion Test)	-	0	-
4(GRADE)	-	0	-
4(TYPE)	-	0	-
5(SIZES)	-	0	-
7.1.1(CONSTRUCTION-Blockboard Core)	-	0	-
7.1.1(CONSTRUCTION-Blockboard Core)	-	0	-
7.1.2(CONSTRUCTION-Blockboard Core)	-	0	-
7.3.2(CONSTRUCTION-Stiles and Rails)	-	0	-
7.3.2(a)(CONSTRUCTION-Stiles and Rails-Joints)	-	0	-
7.3.2(b)(CONSTRUCTION-Stiles and Rails-Joints)	-	0	-
7.3.2(c)(CONSTRUCTION-Stiles and Rails-Joints)	-	0	-
7.3.3(CONSTRUCTION-Stiles and Rails)	-	0	-
9.1(WORKMANSHIP AND FINISH)	-	0	-
9.2(WORKMANSHIP AND FINISH)	-	0	-
9.3(WORKMANSHIP AND FINISH)	-	0	-
11.1(Dimensions and Squareness Test)	-	0	-
11.1(Dimensions and Squareness Test)	-	0	-
11.1(Dimensions and Squareness Test)	-	0	-
11.1(Dimensions and Squareness Test)	-	0	-
11.1(Dimensions and Squareness Test)	-	0	-
11.2(General Flatness Test)	-	0	-
11.2(General Flatness Test)	-	0	-
11.2(General Flatness Test)	-	0	-
11.3(Local Planeness Test)	-	0	-
11.4(Impact Indentation Test)	-	0	-
11.4(Impact Indentation Test)	-	0	-
11.5(Flexure Test)	-	0	-
11.5(Flexure Test)	-	0	-
11.6(Edge Loading Test)	-	0	-
11.6(Edge Loading Test)	-	0	-
11.6(Edge Loading Test)	-	0	-
11.6(Edge Loading Test)	-	0	-
11.7.1(Shock Resistance Test)	-	0	-
11.7.2(Shock Resistance Test)	-	0	-
11.8(Buckling Test)	-	0	-
11.8(Buckling Test)	-	0	-
11.8(Buckling Test)	-	0	-
11.9.2(Slamming Test)	-	0	-
11.9.3(Slamming Test)	-	0	-
11.10(Misuse Test)	-	0	-
11.11(Varying Humidity Test)	-	0	-
11.11(Varying Humidity Test)	-	0	-
11.12(End Immersion Test)	-	0	-
11.13(Knife Test)	-	0	-
11.14(Glue Adhesion Test)	-	0	-
11.15(Screw Withdrawal Resistance Test)	-	0	-
11.15(Screw Withdrawal Resistance Test)	-	0	-
Clause 4.2(grades specified)	-	0	-
Clause 5(SIZES)	-	0	-
Clause 6.1.1(species of timber)	-	0	-
Clause 6.1.2(list of species)	-	0	-
Clause 6.1.3(moisture content)	-	0	-
Clause 6.2.1(Plywood)	-	0	-
Clause 6.2.2(Decorative plywood)	-	0	-
Clause 6.3(Cross-Bands)	-	0	-
Clause 6.4.1(Commercial Face Veneers)	-	0	-
Clause 6.4.2(Decorative Face Veneers)	-	0	-
Clause 6.6.1(Adhesives)	-	0	-
Clause 6.7(Particle Board)	-	0	-
Clause 6.8(Medium density fibre board)	-	0	-
Clause 6.9(Alternative Materials)	-	0	-
Clause 7.1(Blockboard Core)	-	0	-
Clause 7.2(Particle Board or Medium Density Fibre)	-	0	-
Clause 7.3(Stiles and Rails)	-	0	-
Clause 7.4(Levelling)	-	0	-
Clause 7.5(Face Panel)	-	0	-
Clause 7.6(Lipping)	-	0	-
Clause 7.7(Rebating)	-	0	-
Clause 7.8(Opening for Glazing)	-	0	-
Clause 7.9(Venetian)	-	0	-
Clause 8.1(Locks)	-	0	-
Clause 9(WORKMANSHIP AND FINISH)	-	0	-
Clause 10.1(Classification of Tests)	-	0	-
Clause 11.1(Dimensions and Squareness Test)	-	0	-
Clause 11.2(General Flatness Test)	-	0	-
Clause 11.3(Local Planeness Test)	-	0	-
Clause 11.4(Impact Indentation Test)	-	0	-
Clause 11.5(Flexure Test)	-	0	-
Clause 11.6(Edge Loading Test)	-	0	-
Clause 11.7(Shock Resistance Test)	-	0	-
Clause 11.8(Buckling Resistance Test)	-	0	-
Clause 11.9(Slamming Test)	-	0	-
Clause 11.10(Misuse Test)	-	0	-
Clause 11.11(Varying Humidity Test)	-	0	-
Clause 11.12(End Immersion Test)	-	0	-
Clause 11.13(Knife Test)	-	0	-
Clause 11.14(Glue Adhesion Test)	-	0	-
Clause 11.15(Screw Withdrawal Resistance Test)	-	0	-
Clause 12(SAMPLING AND CRITERIA FOR CONFORMITY)	-	0	-
Clause 13(ADDITIONAL REQUIREMENTS FOR ECO MARK)	-	0	-
Clause 14(Marking)	-	0	-
4(Grade, Type and Construction)	-	0	-
5(Sizes and Thickness)	-	0	-
6.1(Timber)	-	0	-
6.2(Plywood for flush door shutter)	-	0	-
6.3(Cross-Bands )	-	0	-
6.4.1(Commercial Face Veneers)	-	0	-
6.4.2(Decorative face veneers)	-	0	-
6.6(Adhesives)	-	0	-
6.7(Particle Board)	-	0	-
6.8(Medium Density Fibre)	-	0	-
6.9(Alternative Materials)	-	0	-
7(Construction)	-	0	-
8.1(Locks)	-	0	-
8.2(Other Fittings)	-	0	-
9(Workmanship and Finish)	-	0	-
10(Tests)	-	0	-
11.1(Dimensions and Squareness Test)	-	0	-
11.2(General Flatness Test)	-	0	-
11.3(Local Planeness Test)	-	0	-
11.4(Impact Indentation Test)	-	0	-
11.5(Flexure Test)	-	0	-
11.6(Edge Loading Test)	-	0	-
11.7(Shock Resistance Test)	-	0	-
11.8(Buckling Resistance Test)	-	0	-
11.9(Slamming Test)	-	0	-
11.1(Misuse Test)	-	0	-
11.11(Varying Humidity Test)	-	0	-
11.12(End Immersion Test)	-	0	-
11.13(Knife Test)	-	0	-
11.14(Glue Adhesion Test)	-	0	-
11.15(Screw Withdrawal Resistance Test)	-	0	-
14(Marking )	-	0	-
Cl-13(ADDITIONAL REQUIREMENTS FOR ECO MARK)	-	0	-

26 Jul, 2027

-
Included w.e.f.13.05.2025

4302

Hi Physix Laboratory India Private Limited, Pune

7126926

IS 302 : Part 2 : Sec 13 (2024)

Household and Similar Electrical Appliances âSafety Part 2 Particular Requirements Section 13 Deep Fat Fryers, Frying Pans and Similar Appliances (First Revision)

66000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking and instructions)	-	2000	-
8(Protection against access to live parts)	-	2000	-
10(Power input and current)	-	2000	-
11(Heating)	-	4000	-
13.1 &13.2(Leakage current test)	-	1500	-
13.1 &13.3(Electric strength test)	-	1500	-
14(Transient overvoltages)	-	2000	-
15(Moisture resistance)	-	4000	-
15.3(Moisture resistance)	-	0	Testing charges included in Cl.15
15.101(Moisture resistance)	-	0	Testing charges included in Cl.15
16.1 &16.2(Leakage current test)	-	1500	-
16.1 & 16.3(Electric strength test)	-	1500	-
17(Overload protection of transformers and associated circuits)	-	4000	-
19.1 to 19.13, Table No. - 9(Abnormal operation)	-	8000	Charges applicable excluding the test of Cl.19.11.4.1 to Cl.19.11.4.7. The testing charges for EMI/EMC Testing (Cl.19.11.4.1 to Cl.19.11.4.7) will be charged extra.
19.101 to to 19.102(Abnormal operation)	-	0	Testing charges included in Cl.19.1 to CL.19.13
20(Stability and mechanical hazards)	-	2000	-
21(Mechanical strength)	-	3000	-
22(Construction)	-	8000	-
22.101(Construction)	-	0	Testing charges included in Cl.22
23(Internal wiring)	-	2000	-
24(Components)	-	3000	-
25("Supply connection and external flexible cords")	-	1000	-
26("Terminals for external conductors")	-	1000	-
27(Provision for earthing)	-	2000	-
28(Screws and connections)	-	1000	-
29("Clearances, creepage distances and solid insulation")	-	2000	-
30(Resistance to heat and fire)	-	3000	-
31(Resistance to rusting)	-	1000	-
32("Radiation, toxicity and similar hazards")	-	1000	-

20 Jun, 2028

-
Included w.e.f 25.03.2025 Exclusion: Cl 24 (Components), Cl 32 ("Radiation, toxicity and similar hazards")

4303

Unique Test House

9134536

IS 9537 : Part 2 (1981)

Specification for conduits for electrical installations: Part 2 rigid steel conduits

ALL GRADE /TYPE/ SIZE

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Marking, IS 9537-2)	-	200	-
6.1(Marking, IS 9537-2)	-	500	-
6.1(Marking, IS 9537-2)	-	500	-
6.3(Marking, Cl. 6.4 of IS 9537-1)	-	500	-
6.2(Marking, IS 9537-2)	-	500	-
7.2.1(Dimensions, (Minimum outside Diameter), IS 9537-2)	-	500	-
7.2.2(Dimensions (Maximum outside Diameter), IS 9537-2)	-	200	-
7.3(Dimensions (Wall thickness), IS 9537-2)	-	200	-
7.3.3(Uniformity of wall thickness, IS 9537-2)	-	300	-
7.4(Screw threads, IS 9537-2)	-	300	-
8.1(Construction, Cl. 8 of IS 9537-1)	-	200	-
8.2(Construction, IS 9537-2)	-	200	-
9.2(Mechanical Properties (Bending test), Cl. 9.3 of IS 9537-1)	-	2000	-
9.3(Mechanical Properties (Compression Test), IS 9537-2)	-	2500	-
13(External Influences, IS 9537-2)	-	200	-
Cl 13.4.5(External Influence ( Outside tube))	-	200	-
Cl 13.4.6(External Influence ( Inside tube))	-	500	-
7.1(Dimensions)	-	500	-

07 Sep, 2028

-
Included w.e.f. 05.03.2025

4304

INDIAN TESTING LABORATORY PRIVATE LIMITED, GREATER NOIDA

8171306

IS 16647 (2017)

Oriented unplasticized polyvinyl chloride (Pvc - O) pipes for water supply - Specification

49000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.5( Density, g/cc)	-	5000	-
9 /9.1 / 27 degree centigrate(MECHANICAL CHARACTERISTICS OF PIPES9./ Resistance to Hydrostatic Pressure)	-	5000	-
7.3( Opacity)	-	5000	-
9.2, table -11( Resistance to External Blows at 0 °C)	-	5000	-
8.2 table-9( Pipe Ends)	-	2000	-
5 / 5.1(MATERIALS )	-	5000	-
5.3(VCM Content)	-	5000	-
5.4( K-Value)	-	5000	-
5.6 / 5.6.1( Material Classification, table -1)	-	1000	-
6.0(CLASSIFICATION OF PIPES, table-2)	-	1000	-
7, see 8.3 and fig-1( GENERAL REQUIREMENTS OF PIPES/ visual appearance)	-	5000	-
7.2( Colour)	-	2000	-
8.1.1, 8.1.1.2, table-3(Dimension of Pipes / Diameter/8.1.1.2 Diameter at any point)	-	5000	-
8.1.2, table 4 to 7(Wall Thickness)	-	2000	-
8.1.3 (Length, meter)	-	2000	-
8.2 table-9(Dimensions of Integral Socket)	-	5000	-
9.3 table-12( Ring Stiffness)	-	5000	-
9.4, annexure-E( Orientation Factor)	-	5000	-
10, table-13( PHYSICAL AND 1CHARACTERISTICS)	-	5000	-
11,11.1( MECHANICAL CHARACTERISTICS OF ASSEMBLIES INCLUDING JOINTS/ 11.1 Assemblies with Non-End-Load-Bearing Joints)	-	5000	-
11.2 / 11.2.1( Short-Term Pressure Test for Leak Tightness of Assemblies)	-	5000	-
11.3( Short-Term Negative Pressure Test for Leak Tightness of Assemblies)	-	5000	-
12(a)( ELASTOMERIC SEALS)	-	5000	-
12(b)( ELASTOMERIC SEALS)	-	5000	-
Cl.10, Table 10/1(Vicat Softening Temp (C))	-	5000	-
Cl.10, Table 10/2(Effect on Water)	-	10000	-
Cl.10, Table 10/3(Resistant to di-chloromethane (Degree of gelation))	-	2000	-
Cl.10, Table 10/4(Alternate Test (Tensile test))	-	5000	-
Cl.10, Table 10/1(Vicat Softening Temp (C))	-	0	-
Cl.10, Table 10/2(Effect on Water)	-	0	-
Cl.10, Table 10/3(Resistant to di-chloromethane (Degree of gelation))	-	0	-
Cl.10, Table 10/4(Alternate Test (Tensile test))	-	0	-
Cl.10, Table 10/1(Vicat Softening Temp (C))	-	0	-
Cl.10, Table 10/2(Effect on Water)	-	0	-
Cl.10, Table 10/3(Resistant to di-chloromethane (Degree of gelation))	-	0	-
Cl.10, Table 10/4(Alternate Test (Tensile test))	-	0	-
Cl.10, Table 10/1(Vicat Softening Temp (C))	-	-	-
Cl.10, Table 10/2(Effect on Water)	-	-	-
Cl.10, Table 10/3(Resistant to di-chloromethane (Degree of gelation))	-	-	-
Cl.10, Table 10/4(Alternate Test (Tensile test))	-	-	-

15 Aug, 2028

-
Included w.e.f.05.05.2025 up to 1000 mm only

4305

URS PRODUCTS AND TESTING PVT. LTD. (A29), NOIDA

8168906

IS 14434 (2023)

POLYCARBONATE MOULDING AND EXTRUSION MATERIALS SPECIFICATION

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2.2.2(Filler Content)	-	1000	-
5(Melt Volume-Flow Rate (MVR))	-	1000	-
5.2(Specific Gravity)	-	1000	-
5.3(Flexural Modulus)	-	1000	-
5.4(Charpy Impact Strength, Notched)	-	1000	-
5.5(Deflection Temperature Under 1.82 MPa)	-	1000	-
5.6.1.2(Overall migration)	-	1000	-
4.2.5(Flammability)	-	1000	-
4.2.5(Optical Properties(% Transmittance))	-	1000	-
4.1(General)	-	1000	-
4.2.2.1(Data Block 2)	-	1000	-
4.2.2.2(Block 2)	-	1000	-
4.2.3(Data Block 3)	-	1000	-
4.2.4 (a)(Melt volume-flow rate)	-	1000	-
4.2.4 (b)(Specific gravity)	-	1000	-
4.2.4 (c)(Flexural modulus)	-	1000	-
4.2.4 (d)(Impact strength)	-	1000	-
4.2.4 (e)(Deflection temperature)	-	1000	-
5.6.1.1(Pigments and colourants)	-	1000	-
5.6.1.2(Overall migration)	-	1000	-
5.6.1.3(Storage and control)	-	1000	-
6(Preparation of Test Specimens)	-	1000	-
8(Packing and Marking)	-	1000	-
4.2.5.2 Table - 6 (i)(Volume resistivity, Min, ohm-cm)	-	1000	-
4.2.5.2 Table - 6 (ii)(Dielectric strength, Min, kV/mm)	-	1000	-
4.2.5.2 Table - 6 (iii)(Dielectric constant at 1 MHz, Max)	-	1000	-
4.2.5.2 Table - 6 (iv)(Dissipation factor at 1 MHz, Max)	-	1000	-
4.2.5.2 Table 6 Sr.No.(i)(Volume resistivity)	-	1000	-
4.2.5.2 Table 6 Sr.No.(ii)(Dielectric strength)	-	1000	-
4.2.5.2 Table 6 Sr.No.(ii)(Dielectric Constant)	-	1000	-
4.2.5.2 Table 6 Sr.No.(ii)(Dissipation factor)	-	1000	-

26 Sep, 2027

-
Included w.e.f 21.05.2025

4306

RAMCO RESEARCH AND DEVOLPMENT CENTRE, CHENNAI

6183606

IS 16415 (2015)

Composite cement - Specification

35100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Physical Requirement)	-	15000	-
7 and Table 3 i(Fineness IS 4031(Part 2))	-	2000	-
7 and Table 3 ii a(Soundness, Le-Chate1ier expansion IS 4031(Part 3) )	-	2000	-
7 and Table 3 ii b(Soundness, Autoclave expansion IS 4031(Part 3) )	-	2000	-
7 and Table 3 iii a(Setting Time ( by Vicat Apparatus), Initial IS 4031(Part 5))	-	2000	-
7 and Table 3 iii b(Setting Time ( by Vicat Apparatus ), Final IS 4031(Part 5))	-	2000	-
7 and Table 3 iv a(Compretsive Strenqth .72 ± 1 hr IS 4031(Part 6))	-	3000	-
7 and Table 3 iv b(Compretsive Strenqth 168 ± 2 hr IS 4031(Part 6))	-	3000	-
7 and Table 3 iv c(Compretsive Strenqth 672 ± 4 hr IS 4031(Part 6))	-	3000	-
7 and Table 3 v(Drying shrinkage IS 4031(Part 10))	-	2000	-
7 and Table 3 i(Fineness IS 4031(Part 2))	-	2000	-
7 and Table 3 ii a(Soundness, Le-Chate1ier expansion IS 4031(Part 3) )	-	2000	-
7 and Table 3 ii b(Soundness, Autoclave expansion IS 4031(Part 3) )	-	2000	-
7 and Table 3 iv a(Compretsive Strenqth .72 ± 1 hr IS 4031(Part 6))	-	3000	-
6(Chemical Requirements)	-	15500	-
6 -Table - 2 i(Insoluble residue - Cl 4.10 of IS 4032:1985)	-	1800	-
6 -Table - 2 ii(Magnesia - Cl 4.8 of IS 4032:1985)	-	1000	-
6 -Table - 2 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-	1800	-
6 -Table - 2 iv(Sulphide sulphur (S) - Cl 6.12 of IS 4032:1985)	-	1800	-
6 -Table - 2 v(Loss on ignition - Cl 4.2 of IS 4032:1985)	-	1000	-
6 -Table - 2 vi(Chloride content - Cl 4.13 of IS 4032:1985)	-	1500	-
6 -Table - 2 i(Insoluble residue - Cl 4.10 of IS 4032:1985)	-	1800	-
6 -Table - 2 ii(Magnesia - Cl 4.8 of IS 4032:1985)	-	1000	-
6 -Table - 2 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-	1800	-
6 -Table - 2 iv(Sulphide sulphur (S) - Cl 6.12 of IS 4032:1985)	-	1800	-
6 -Table - 2 v(Loss on ignition - Cl 4.2 of IS 4032:1985)	-	1000	-
6 -Table - 2 vi(Chloride content - Cl 4.13 of IS 4032:1985)	-	1800	-
Cl. 6.1,Table 2(Alkali content)	-	2000	-
Cl. 6.1,Table 2(Chloride content)	-	1800	-
Cl. 6.1,Table 2(Loss on ignition)	-	1000	-
Cl. 6.1,Table 2(Suilphide sulphur)	-	1800	-
Cl. 6.1,Table 2(Total sulphur content calculated as sulphuric anhydride)	-	1800	-
Cl. 6.1,Table 2(Magnesia)	-	1000	-
Cl. 6.1,Table 2(Insoluble residue)	-	1800	-
7 and Table 3 vi(Transverse strength (optional) IS 4031(Part 8) )	-	2000	-
7 and Table 3 iii a(Setting Time ( by Vicat Apparatus), Initial IS 4031(Part 5))	-	2000	-
7 and Table 3 iii b(Setting Time ( by Vicat Apparatus ), Final IS 4031(Part 5))	-	2000	-
7 and Table 3 iv b(Compretsive Strenqth 168 ± 2 hr IS 4031(Part 6))	-	3000	-
7 and Table 3 iv c(Compretsive Strenqth 672 ± 4 hr IS 4031(Part 6))	-	3000	-
7 and Table 3 v(Drying shrinkage IS 4031(Part 10))	-	2000	-
7(Physical Requirement)	-	15500	-
6(Chemical Requirements)	-	15000	-
Cl. 6.1,Table 2(Alkali content)	-	2000	-
Cl. 6.1,Table 2(Chloride content)	-	1500	-
Cl. 6.1,Table 2(Loss on ignition)	-	1500	-
Cl. 6.1,Table 2(Suilphide sulphur)	-	1800	-
Cl. 6.1,Table 2(Total sulphur content calculated as sulphuric anhydride)	-	1800	-
Cl. 6.1,Table 2(Magnesia)	-	1000	-
Cl. 6.1,Table 2(Insoluble residue)	-	1800	-
7(Physical Requirement)	-	15500	-
6(Chemical Requirements)	-	15000	-
Cl. 6.1,Table 2(Alkali content)	-	2000	-
Cl. 6.1,Table 2(Chloride content)	-	1500	-
Cl. 6.1,Table 2(Loss on ignition)	-	1500	-
Cl. 6.1,Table 2(Suilphide sulphur)	-	1800	-
Cl. 6.1,Table 2(Total sulphur content calculated as sulphuric anhydride)	-	1800	-
Cl. 6.1,Table 2(Magnesia)	-	1000	-
Cl. 6.1,Table 2(Insoluble residue)	-	1800	-
7(Physical Requirement)	-	-	-
6(Chemical Requirements)	-	-	-
Cl. 6.1,Table 2(Alkali content)	-	-	-
Cl. 6.1,Table 2(Chloride content)	-	-	-
Cl. 6.1,Table 2(Loss on ignition)	-	-	-
Cl. 6.1,Table 2(Suilphide sulphur)	-	-	-
Cl. 6.1,Table 2(Total sulphur content calculated as sulphuric anhydride)	-	-	-
Cl. 6.1,Table 2(Magnesia)	-	-	-
Cl. 6.1,Table 2(Insoluble residue)	-	-	-

12 Jan, 2028

-
Included w.e.f 18.07.2025 Exclusion: Cl 7 & Table 3(vi) Transverse Strength(optional)

4307

Conformity Testing Labs Pvt. Ltd. Unit 2 (A33)

8139626

IS 2993 : Part 2 (2024)

a.c. Motor Capacitors Part 2 Motor Start Capacitors ( Third Revision )

375000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.7(Voltage test between the terminals)	-	5000	-
5.1.8(Voltage test between terminals and case)	-	5000	-
5.1.9(Capacitance measurement)	-	5000	-
5.1.10(Check of dimensions)	-	5000	-
5.1.11.1(Robustness of terminations)	-	5000	-
5.1.11.2(Soldering)	-	5000	-
5.1.11.3(Vibration)	-	5000	-
5.1.12(Sealing test)	-	5000	-
5.1.13(Endurance test)	-	120000	-
5.1.14(Damp heat test)	-	120000	-
5.1.15(Self-healing test)	-	20000	-
5.1.16(Destruction test)	-	30000	-
5.1.17.1(Ball-pressure test)	-	20000	-
5.1.17.2(Glow-wire test)	-	5000	-
5.1.17.3(Tracking test)	-	5000	-
5.2(Overloads)	-	5000	-
5.3.2(Terminals and connecting cables)	-	5000	-
5.3.3(Earth connections)	-	5000	-
5.3.4(Discharge devices)	-	5000	-
5.3.5(Pollution)	-	5000	-
5.4(Marking)	-	5000	-
6.1.6(Voltage test between the terminals)	-	5000	-
6.1.7(Voltage test between terminals and case)	-	5000	-
6.1.8(Capacitance and power factor measurement)	-	5000	-
6.1.9(Check of dimensions)	-	5000	-
6.1.10.1(Robustness of terminations)	-	5000	-
6.1.10.2(Soldering)	-	5000	-
6.1.10.3(Vibration)	-	5000	-
6.1.10.4(Fixing bolt or stud (if fitted))	-	5000	-
6.1.10.5(Rapid change of temperature)	-	5000	-
6.1.11(Sealing test)	-	5000	-
6.1.12(Endurance test)	-	120000	-
6.1.13(Damp heat test)	-	120000	-
6.1.14(Pressure relief test)	-	5000	-
6.3.1(Creepage distances and clearances)	-	5000	-
6.4(Marking)	-	5000	-
7.2.1(Measurement of working voltage)	-	5000	-
7.2.2(Influence of capacitance)	-	5000	-
7.3(Checking capacitor temperature)	-	5000	-
7.4(Checking transients)	-	5000	-
7.5(Storage of electrolytic capacitors)	-	5000	-
Annex A(Test voltage)	-	5000	-
5.1.1.1(General)	-	5000	-
5.3.1(Creepage distances and clearances)	-	5000	-
6.1.15.1(Ball-pressure test)	-	20000	-
6.1.15.2(Glow-wire test)	-	25000	-
6.1.15.3(Tracking test)	-	5000	-
6.2(Overloads)	-	5000	-
6.3.2(Terminals and connecting cables)	-	5000	-
6.3.3(Earth connections)	-	5000	-
6.3.4(Discharge devices)	-	5000	-
6.3.5(Pollution)	-	5000	-
6.1.10.4(Fixing bolt or stud (if fitted))	-	5000	-
5.1.10(Check of dimensions)	-	5000	-
5.1.7(Voltage test between the terminals)	-	5000	-
5.1.8(Voltage test between terminals and case)	-	5000	-
5.1.9(Capacitance measurement)	-	5000	-
5.1.10(Check of dimensions)	-	5000	-
5.1.11.1(Robustness of terminations)	-	5000	-
5.1.11.2(Soldering)	-	5000	-
5.1.11.3(Vibration)	-	5000	-
5.1.12(Sealing test)	-	5000	-
5.1.13(Endurance test)	-	100000	-
5.1.14(Damp heat test)	-	120000	-
5.1.15(Self-healing test)	-	20000	-
5.1.16(Destruction test)	-	30000	-
5.1.17.1(Ball-pressure test)	-	20000	-
5.1.17.2(Glow-wire test)	-	5000	-
5.1.17.3(Tracking test)	-	5000	-
5.2(Overloads)	-	5000	-
5.3.2(Terminals and connecting cables)	-	5000	-
5.3.3(Earth connections)	-	5000	-
5.3.4(Discharge devices)	-	5000	-
5.3.5(Pollution)	-	5000	-
5.4(Marking)	-	5000	-
6.1.6(Voltage test between the terminals)	-	5000	-
6.1.7(Voltage test between terminals and case)	-	5000	-
6.1.8(Capacitance and power factor measurement)	-	5000	-
6.1.9(Check of dimensions)	-	5000	-
6.1.10.1(Robustness of terminations)	-	5000	-
6.1.10.2(Soldering)	-	5000	-
6.1.10.3(Vibration)	-	5000	-
6.1.10.4(Fixing bolt or stud (if fitted))	-	5000	-
6.1.10.5(Rapid change of temperature)	-	5000	-
6.1.11(Sealing test)	-	5000	-
6.1.12(Endurance test)	-	100000	-
6.1.13(Damp heat test)	-	120000	-
6.1.14(Pressure relief test)	-	5000	-
6.3.1(Creepage distances and clearances)	-	5000	-
6.4(Marking)	-	5000	-
7.2.1(Measurement of working voltage)	-	5000	-
7.2.2(Influence of capacitance)	-	5000	-
7.3(Checking capacitor temperature)	-	5000	-
7.4(Checking transients)	-	5000	-
7.5(Storage of electrolytic capacitors)	-	5000	-
Annex A(Test voltage)	-	5000	-
5.1.1.1(General)	-	5000	-
5.3.1(Creepage distances and clearances)	-	5000	-
6.1.15.1(Ball-pressure test)	-	20000	-
6.1.15.2(Glow-wire test)	-	5000	-
6.1.15.3(Tracking test)	-	5000	-
6.2(Overloads)	-	5000	-
6.3.2(Terminals and connecting cables)	-	5000	-
6.3.3(Earth connections)	-	5000	-
6.3.4(Discharge devices)	-	5000	-
6.3.5(Pollution)	-	5000	-
6.1.10.4(Fixing bolt or stud (if fitted))	-	5000	-
5.1.10(Check of dimensions)	-	5000	-

05 Apr, 2027

-
Included w.e.f 25.03.2025

4308

Bahadurgarh Footwear Development Services (BFDS), Bahadurgarh

8168806

IS 6721 (2023)

SANDAL AND SLIPPERS SPECIFICATION First revision

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No.4(SHAPE AND DESIGN)	-	200	-
Cl. No.5("SIZE AND FITTINGS ")	-	200	-
Cl. No.6("CONSTRUCTION ")	-	200	-
Cl. No.7(MATERIAL)	-	200	-
Cl. No.8.1, Table no. 1(i),a("Tear strength, (other than moulded upper material) ")	-	450	-
Cl. No.8.1, Table no. 1(i),b("For all moulded upper material ")	-	450	-
Cl. No.8.1, Table no. 1(ii)(Flexing endurance)	-	600	-
Cl. No.8.2,Table no. 2(i)(Tear strength)	-	450	-
Cl. No.8.2,Table no. 2(ii),a("Abrasion resistance- At dry condition")	-	600	-
Cl. No.8.2,Table no. 2(ii),b("Abrasion resistance- At wet condition")	-	600	-
Cl. No.8.3,Table no. 3(i)(Tear strength)	-	450	-
Cl. No.8.3,Table no. 3(ii),a("Abrasion resistance- At dry condition")	-	600	-
Cl. No.8.3,Table no. 3(ii),b("Abrasion resistance- At wet condition")	-	600	-
Cl. No.8.4,Table no. 4(i)(Grain crack index)	-	500	-
Cl. No.8.4,Table no. 4(ii)(Density)	-	200	-
Cl. No.8.4,Table no. 4(iii)(Abrasion resistance)	-	600	-
Cl. No.8.4,Table no. 5(i)(Density)	-	200	-
Cl. No.8.4,Table no. 5(ii)("Abrasion resistance, Volume loss ")	-	600	-
Cl. No.8.4, Table no. 5(iii)("Flexing resistance, At 30 000 flexes")	-	600	-
Cl. No.8.5, Table no. 6(i)("Bond strength, N/mm, Min (Applicable when fore part is fully covered or strap width is more than 25 mm)")	-	500	-
Cl. No.8.5, Table no. 6(ii)("Toe post attachment strength, N, Min (Applicable if toe post is present)")	-	500	-
Cl. No.8.5, Table no. 6(iii)("Toe ring attachment strength, Min (Applicable if toe ring is not integral part of upper")	-	500	-
Cl. No.8.5, Table no. 6(iv)(Strap to outsole strength)	-	500	-
Cl. No.8.5, Table no. 6(v)("Attachment strength of back strap and Buckle/D-ring ")	-	500	-
Cl. No.8.5, Table no. 6(vi)("Attachment strength of elastic, limit of useful extension, percent")	-	500	-
Cl. No.8.5, Table no. 6(vii)("Attachment strength of back strap and velcro, N, Min (If, present)")	-	500	-
Cl. No.8.5, Table no. 6(viii)("Hydrolysis resistance, Cut growth after 150 000 flexes, mm, Max (Applicable for PU sole only)")	-	2000	-
Cl. No.8.5, Table no. 6(ix)("Heel pull off strength, N, Min (Applicable for heel height 40 mm and above attached separately to the sandal/slipper)")	-	500	-
Cl. No.8.5, Table no. 6(x)("Inter layer bond strength, N/mm, (Applicable for multi-layer sole)")	-	500	-
Cl. No.8.5, Table no. 6(xi)("Slip Resistance, Coefficient of Friction (COF) (Not applicable for leather sole) (To be carried out on quarry tiles)")	-	1200	-
Cl. No.9.(MARKING AND PACKING)	-	500	-

02 Sep, 2027

-
Exclusion: Table 1 xiv Chemical requirement and Table 1 xv Lead content

4309

Bahadurgarh Footwear Development Services (BFDS), Bahadurgarh

8168806

IS 10702 (2023)

Hawai Chappal-Specification

6500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Material)	-	200	-
4.2(Length)	-	200	-
4.3(Thickness)	-	200	-
4.4 , Table No. 1 , i)(Density)	-	200	-
4.4 , Table No. 1 , ii)(2Compression set at constant stress)	-	500	-
4.4 , Table No. 1 , iii)(3Split tear strength)	-	450	-
4.4 , Table No. 1 , iv)("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber")	-	600	-
4.4 , Table No. 1 , v)(5Abrasion resistance at applied force)	-	600	-
4.4 , Table No. 1 , vi)(Flexing resistance: Maximum cut growth at 50 000 flexes)	-	600	-
4.4 , Table No. 1 , vii)(7 Hydrolysis resistance, Maximum cut growth at 50 000 flexes)	-	2000	-
4.4 , Table No . 2 , i)(Density , Solid strap, Cellular strap)	-	200	-
4.4 , Table No . 2 , ii)("Breaking strength , Strap to strap and Toe portion to strap , Elongation at break")	-	450	-
4.4 , Table No . 2 , iii)(Minimum cross section of the stud)	-	500	-
4.4 , Table No . 2 , iv)(Stud bolt)	-	200	-
4.4 , Table No . 3 , i)(Toe post attachment strength)	-	500	-
4.4 , Table No . 3 , ii)(Attachment strength of rear strap)	-	500	-
4.4 , Table No . 3 , iii)(Inter layer bond strength)	-	500	-
6(MARKING AND PACKING)	-	500	-
Cl. No.5.1,Table no.1 of IS 17011(iv)(Chromium (VI))	-	600	-
Cl. No.5.1,Table no.1 of IS 17011(x)(pH)	-	400	-
Clause 4.1 - 4.1.1(Bottom Material)	-	200	-
Clause 4.1 - 4.1.2(Strap Material)	-	200	-
Clause 4.1 - 4.1.4(Material)	-	200	-
Clause 4.2(Material)	-	200	-
Clause 4.3 - 4.3.1(Thickness)	-	200	-
Clause 4.3 - 4.3.2(Thickness)	-	200	-
Clause 4.4 Table 1 -i)(Density, g/cm3, Min)	-	200	-
Clause 4.4 Table 2 -i) - b(Density, g/cm3 Cellular strap)	-	200	-
Clause 4.4 Table 1 -iii)(Split tear strength, kg, Min)	-	450	-
Clause 4.4 Table 1 -iv) - a("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, percent, Max")	-	600	-
Clause 4.4 Table 1 -iv) - b(Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber, percent, Max)	-	600	-
Clause 4.4 Table 1 -v)(Abrasion resistance at applied force 5 N)	-	600	-
Clause 4.4 Table 2 -i) - a("Density, g/cm3 Solid strap ")	-	200	-
Clause 4.4 Table 2 -ii) - a - 1("Breaking strength, kgf, Min Strap to strap(Solid Strap)")	-	450	-
Clause 4.4 Table 2 -ii) - a - 2("Breaking strength, kgf, Min Strap to strap(Cellular Strap)")	-	450	-
Clause 4.4 Table 2 -ii) - a - 3("Breaking strength, kgf, Min Toe portion to strap(Solid Strap)")	-	450	-
Clause 4.4 Table 2 -ii) - a - 4("Breaking strength, kgf, Min Toe portion to strap(Cellular Strap)")	-	450	-
Clause 4.4 Table 2 -ii) - b - 1("Elongation at break, percent (Applicable to strap to strap (V shape) Solid Strap")	-	450	-
Clause 4.4 Table 2 -ii) - b - 2("Elongation at break, percent (Applicable to strap to strap (V shape) Cellular Strap")	-	450	-
Clause 4.4 Table 2 -iii) - a("Minimum cross section of the stud, mm, Size 1 to 13 (Adult)")	-	200	-
Clause 4.4 Table 2 -iii) - b("Minimum cross section of the stud, mm, Size 3 to 13 (Children)")	-	200	-
Clause 4.4 Table 2 -iv) - a("Stud bolt, mm Diameter/edge to edge length")	-	200	-
Clause 4.4 Table 2 -iv) - b("Stud bolt, mm Thickness")	-	200	-
Clause 4.4 Table 3 -i)("Toe post attachment strength, N, Min")	-	450	-
Clause 4.4 Table 3 -iii)("Inter layer bond strength, N/mm, Min")	-	500	-
Clause 4.1 - 4.1.3(Material)	-	200	-
Clause 4.4 Table 3 -ii)("Attachment strength of rear strap, N, Min")	-	450	-
4.1(Material)	-	200	-
4.2(Length)	-	200	-
4.3(Thickness)	-	200	-
4.4 , Table No. 1 , i)(Density)	-	200	-
4.4 , Table No. 1 , ii)(2Compression set at constant stress)	-	500	-
4.4 , Table No. 1 , iii)(3Split tear strength)	-	450	-
4.4 , Table No. 1 , iv)("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber")	-	600	-
4.4 , Table No. 1 , v)(5Abrasion resistance at applied force)	-	600	-
4.4 , Table No. 1 , vi)(Flexing resistance: Maximum cut growth at 50 000 flexes)	-	600	-
4.4 , Table No. 1 , vii)(7 Hydrolysis resistance, Maximum cut growth at 50 000 flexes)	-	2000	-
4.4 , Table No . 2 , i)(Density , Solid strap, Cellular strap)	-	200	-
4.4 , Table No . 2 , ii)("Breaking strength , Strap to strap and Toe portion to strap , Elongation at break")	-	500	-
4.4 , Table No . 2 , iii)(Minimum cross section of the stud)	-	200	-
4.4 , Table No . 2 , iv)(Stud bolt)	-	200	-
4.4 , Table No . 3 , i)(Toe post attachment strength)	-	500	-
4.4 , Table No . 3 , ii)(Attachment strength of rear strap)	-	500	-
4.4 , Table No . 3 , iii)(Inter layer bond strength)	-	500	-
6(MARKING AND PACKING)	-	200	-
Cl. No.5.1,Table no.1 of IS 17011(iv)(Chromium (VI))	-	800	-
Cl. No.5.1,Table no.1 of IS 17011(x)(pH)	-	500	-
Clause 4.1 - 4.1.1(Bottom Material)	-	200	-
Clause 4.1 - 4.1.2(Strap Material)	-	200	-
Clause 4.1 - 4.1.4(Material)	-	200	-
Clause 4.2(Material)	-	200	-
Clause 4.3 - 4.3.1(Thickness)	-	200	-
Clause 4.3 - 4.3.2(Thickness)	-	200	-
Clause 4.4 Table 1 -i)(Density, g/cm3, Min)	-	200	-
Clause 4.4 Table 2 -i) - b(Density, g/cm3 Cellular strap)	-	200	-
Clause 4.4 Table 1 -iii)(Split tear strength, kg, Min)	-	450	-
Clause 4.4 Table 1 -iv) - a("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, percent, Max")	-	600	-
Clause 4.4 Table 1 -iv) - b(Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber, percent, Max)	-	600	-
Clause 4.4 Table 1 -v)(Abrasion resistance at applied force 5 N)	-	600	-
Clause 4.4 Table 2 -i) - a("Density, g/cm3 Solid strap ")	-	200	-
Clause 4.4 Table 2 -ii) - a - 1("Breaking strength, kgf, Min Strap to strap(Solid Strap)")	-	500	-
Clause 4.4 Table 2 -ii) - a - 2("Breaking strength, kgf, Min Strap to strap(Cellular Strap)")	-	500	-
Clause 4.4 Table 2 -ii) - a - 3("Breaking strength, kgf, Min Toe portion to strap(Solid Strap)")	-	500	-
Clause 4.4 Table 2 -ii) - a - 4("Breaking strength, kgf, Min Toe portion to strap(Cellular Strap)")	-	500	-
Clause 4.4 Table 2 -ii) - b - 1("Elongation at break, percent (Applicable to strap to strap (V shape) Solid Strap")	-	450	-
Clause 4.4 Table 2 -ii) - b - 2("Elongation at break, percent (Applicable to strap to strap (V shape) Cellular Strap")	-	450	-
Clause 4.4 Table 2 -iii) - a("Minimum cross section of the stud, mm, Size 1 to 13 (Adult)")	-	200	-
Clause 4.4 Table 2 -iii) - b("Minimum cross section of the stud, mm, Size 3 to 13 (Children)")	-	200	-
Clause 4.4 Table 2 -iv) - a("Stud bolt, mm Diameter/edge to edge length")	-	200	-
Clause 4.4 Table 2 -iv) - b("Stud bolt, mm Thickness")	-	200	-
Clause 4.4 Table 3 -i)("Toe post attachment strength, N, Min")	-	500	-
Clause 4.4 Table 3 -iii)("Inter layer bond strength, N/mm, Min")	-	500	-
Clause 4.1 - 4.1.3(Material)	-	200	-
Clause 4.4 Table 3 -ii)("Attachment strength of rear strap, N, Min")	-	500	-
4.4 , Table No. 1 , vi)(Flexing resistance: Maximum cut growth at 50 000 flexes)	-	800	-
4.4 , Table No. 1 , vii)(7 Hydrolysis resistance, Maximum cut growth at 50 000 flexes)	-	2500	-
4.4 , Table No . 2 , ii)("Breaking strength , Strap to strap and Toe portion to strap , Elongation at break")	-	450	-
6(MARKING AND PACKING)	-	500	-
Clause 4.4 Table 1 -iv) - a("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, percent, Max")	-	800	-
Clause 4.4 Table 1 -iv) - b(Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber, percent, Max)	-	800	-
Clause 4.4 Table 2 -ii) - b - 1("Elongation at break, percent (Applicable to strap to strap (V shape) Solid Strap")	-	500	-
Clause 4.4 Table 2 -ii) - b - 2("Elongation at break, percent (Applicable to strap to strap (V shape) Cellular Strap")	-	500	-
Clause 4.4 Table 2 -iii) - a("Minimum cross section of the stud, mm, Size 1 to 13 (Adult)")	-	500	-
Clause 4.4 Table 2 -iii) - b("Minimum cross section of the stud, mm, Size 3 to 13 (Children)")	-	500	-
Clause 4.4 Table 2 -iv) - a("Stud bolt, mm Diameter/edge to edge length")	-	500	-
Cl-4 ((Amendment No-1)(Category And Type)	-	200	-
Cl-4.4, Table -1 S. No-1 (i) (Amendment No-1)(Compression set at constant stress)	-	500	-
Cl-4.4, Table -1 S. No-1 (ii) (Amendment No-1)(Split tear strength)	-	450	-
Cl-4.4, Table -1 S. No-1 (iii) (a)(Amendment No-1)("Shrinkage at Shrinkage at 50 °C ± 1 °C for 2 h for polymeric material, percent, Max ")	-	800	-
Cl-4.4, Table -1 S. No-1 (iii)(b) (Amendment No-1)(Shrinkage at 100 °C ± 1 °C for 1 h for rubber, percent, Max)	-	800	-
Cl-4.4, Table -1 S. No-1 (iv) (Amendment No-1)(Abrasion resistance at applied force)	-	600	-
Cl-4.4, Table -1 S. No-1 (v) (Amendment No-1)(Flexing resistance: Maximum cut growth,)	-	600	-
Cl-4.4, Table -1 S. No-1 (vi) (Amendment No-1)(Hydrolysis resistance:Maximum cut growth)	-	2500	-
Cl-4.4, Table -2 S. No-1 (i), a (Amendment No-1)("Breaking strength for Strap to strap 1-Solid strap 2-Cellular strap")	-	500	-
Cl-4.4, Table -2 S. No-1 (i), b (Amendment No-1)("Breaking strength for Toe portion to strap 1-Solid strap 2-Cellular strap")	-	500	-
Cl-4.4, Table -2 S. No-1 (i), c (Amendment No-1)("Elongation at break , percent, Min 1-Solid strap 2-Cellular strap")	-	450	-
Cl-4.4, Table -3 S. No-1 (i), (Amendment No-1)(Toe post attachment strength)	-	500	-
Cl-4.4, Table -3 S. No-1 (ii), (Amendment No-1)(Attachment strength of rear strap)	-	500	-
Cl-4.4, Table -3 S. No-1 (iii), (Amendment No-1)(Inter layer bond strength)	-	500	-
4.4 , Table No. 1 , iv)("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber")	-	800	-
Clause 4.4 Table 2 -ii) - a - 1("Breaking strength, kgf, Min Strap to strap(Solid Strap)")	-	450	-
Clause 4.4 Table 2 -ii) - a - 2("Breaking strength, kgf, Min Strap to strap(Cellular Strap)")	-	450	-
Clause 4.4 Table 2 -ii) - a - 3("Breaking strength, kgf, Min Toe portion to strap(Solid Strap)")	-	450	-
Clause 4.4 Table 2 -ii) - a - 4("Breaking strength, kgf, Min Toe portion to strap(Cellular Strap)")	-	450	-
Clause 4.4 Table 3 -ii)("Attachment strength of rear strap, N, Min")	-	450	-
Cl-4 ((Amendment No-1)(Category And Type)	-	450	-
Cl-4.4, Table -1 S. No-1 (i) (Amendment No-1)(Compression set at constant stress)	-	500	-
Cl-4.4, Table -1 S. No-1 (ii) (Amendment No-1)(Split tear strength)	-	450	-
Cl-4.4, Table -1 S. No-1 (iii) (a)(Amendment No-1)("Shrinkage at Shrinkage at 50 °C ± 1 °C for 2 h for polymeric material, percent, Max ")	-	800	-
Cl-4.4, Table -1 S. No-1 (iii)(b) (Amendment No-1)(Shrinkage at 100 °C ± 1 °C for 1 h for rubber, percent, Max)	-	800	-
Cl-4.4, Table -1 S. No-1 (iv) (Amendment No-1)(Abrasion resistance at applied force)	-	600	-
Cl-4.4, Table -1 S. No-1 (v) (Amendment No-1)(Flexing resistance: Maximum cut growth,)	-	800	-
Cl-4.4, Table -1 S. No-1 (vi) (Amendment No-1)(Hydrolysis resistance:Maximum cut growth)	-	2500	-
Cl-4.4, Table -2 S. No-1 (i), a (Amendment No-1)("Breaking strength for Strap to strap 1-Solid strap 2-Cellular strap")	-	450	-
Cl-4.4, Table -2 S. No-1 (i), b (Amendment No-1)("Breaking strength for Toe portion to strap 1-Solid strap 2-Cellular strap")	-	450	-
Cl-4.4, Table -2 S. No-1 (i), c (Amendment No-1)("Elongation at break , percent, Min 1-Solid strap 2-Cellular strap")	-	450	-
Cl-4.4, Table -3 S. No-1 (i), (Amendment No-1)(Toe post attachment strength)	-	500	-
Cl-4.4, Table -3 S. No-1 (ii), (Amendment No-1)(Attachment strength of rear strap)	-	450	-
Cl-4.4, Table -3 S. No-1 (iii), (Amendment No-1)(Inter layer bond strength)	-	500	-
4.4 , Table No . 2 , iii)(Minimum cross section of the stud)	-	500	-
Clause 4.1 - 4.1.2(Strap Material)	-	450	-
Clause 4.4 Table 2 -iii) - a("Minimum cross section of the stud, mm, Size 1 to 13 (Adult)")	-	450	-
Clause 4.4 Table 2 -iii) - b("Minimum cross section of the stud, mm, Size 3 to 13 (Children)")	-	450	-
Cl-4 ((Amendment No-1)(Category And Type)	-	200	-
Cl-4.4, Table -1 S. No-1 (v) (Amendment No-1)(Flexing resistance: Maximum cut growth,)	-	600	-
Cl-4.4, Table -3 S. No-1 (ii), (Amendment No-1)(Attachment strength of rear strap)	-	500	-
4.1(Material)	-	-	-
4.2(Length)	-	-	-
4.3(Thickness)	-	-	-
4.4 , Table No. 1 , i)(Density)	-	-	-
4.4 , Table No. 1 , ii)(2Compression set at constant stress)	-	-	-
4.4 , Table No. 1 , iii)(3Split tear strength)	-	-	-
4.4 , Table No. 1 , iv)("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber")	-	-	-
4.4 , Table No. 1 , v)(5Abrasion resistance at applied force)	-	-	-
4.4 , Table No. 1 , vi)(Flexing resistance: Maximum cut growth at 50 000 flexes)	-	-	-
4.4 , Table No. 1 , vii)(7 Hydrolysis resistance, Maximum cut growth at 50 000 flexes)	-	-	-
4.4 , Table No . 2 , i)(Density , Solid strap, Cellular strap)	-	-	-
4.4 , Table No . 2 , ii)("Breaking strength , Strap to strap and Toe portion to strap , Elongation at break")	-	-	-
4.4 , Table No . 2 , iii)(Minimum cross section of the stud)	-	-	-
4.4 , Table No . 2 , iv)(Stud bolt)	-	-	-
4.4 , Table No . 3 , i)(Toe post attachment strength)	-	-	-
4.4 , Table No . 3 , ii)(Attachment strength of rear strap)	-	-	-
4.4 , Table No . 3 , iii)(Inter layer bond strength)	-	-	-
6(MARKING AND PACKING)	-	-	-
Cl. No.5.1,Table no.1 of IS 17011(iv)(Chromium (VI))	-	-	-
Cl. No.5.1,Table no.1 of IS 17011(x)(pH)	-	-	-
Clause 4.1 - 4.1.1(Bottom Material)	-	-	-
Clause 4.1 - 4.1.2(Strap Material)	-	-	-
Clause 4.1 - 4.1.4(Material)	-	-	-
Clause 4.2(Material)	-	-	-
Clause 4.3 - 4.3.1(Thickness)	-	-	-
Clause 4.3 - 4.3.2(Thickness)	-	-	-
Clause 4.4 Table 1 -i)(Density, g/cm3, Min)	-	-	-
Clause 4.4 Table 2 -i) - b(Density, g/cm3 Cellular strap)	-	-	-
Clause 4.4 Table 1 -iii)(Split tear strength, kg, Min)	-	-	-
Clause 4.4 Table 1 -iv) - a("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, percent, Max")	-	-	-
Clause 4.4 Table 1 -iv) - b(Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber, percent, Max)	-	-	-
Clause 4.4 Table 1 -v)(Abrasion resistance at applied force 5 N)	-	-	-
Clause 4.4 Table 2 -i) - a("Density, g/cm3 Solid strap ")	-	-	-
Clause 4.4 Table 2 -ii) - a - 1("Breaking strength, kgf, Min Strap to strap(Solid Strap)")	-	-	-
Clause 4.4 Table 2 -ii) - a - 2("Breaking strength, kgf, Min Strap to strap(Cellular Strap)")	-	-	-
Clause 4.4 Table 2 -ii) - a - 3("Breaking strength, kgf, Min Toe portion to strap(Solid Strap)")	-	-	-
Clause 4.4 Table 2 -ii) - a - 4("Breaking strength, kgf, Min Toe portion to strap(Cellular Strap)")	-	-	-
Clause 4.4 Table 2 -ii) - b - 1("Elongation at break, percent (Applicable to strap to strap (V shape) Solid Strap")	-	-	-
Clause 4.4 Table 2 -ii) - b - 2("Elongation at break, percent (Applicable to strap to strap (V shape) Cellular Strap")	-	-	-
Clause 4.4 Table 2 -iii) - a("Minimum cross section of the stud, mm, Size 1 to 13 (Adult)")	-	-	-
Clause 4.4 Table 2 -iii) - b("Minimum cross section of the stud, mm, Size 3 to 13 (Children)")	-	-	-
Clause 4.4 Table 2 -iv) - a("Stud bolt, mm Diameter/edge to edge length")	-	-	-
Clause 4.4 Table 2 -iv) - b("Stud bolt, mm Thickness")	-	-	-
Clause 4.4 Table 3 -i)("Toe post attachment strength, N, Min")	-	-	-
Clause 4.4 Table 3 -iii)("Inter layer bond strength, N/mm, Min")	-	-	-
Clause 4.1 - 4.1.3(Material)	-	-	-
Clause 4.4 Table 3 -ii)("Attachment strength of rear strap, N, Min")	-	-	-
Cl-4 ((Amendment No-1)(Category And Type)	-	-	-
Cl-4.4, Table -1 S. No-1 (i) (Amendment No-1)(Compression set at constant stress)	-	-	-
Cl-4.4, Table -1 S. No-1 (ii) (Amendment No-1)(Split tear strength)	-	-	-
Cl-4.4, Table -1 S. No-1 (iii) (a)(Amendment No-1)("Shrinkage at Shrinkage at 50 °C ± 1 °C for 2 h for polymeric material, percent, Max ")	-	-	-
Cl-4.4, Table -1 S. No-1 (iii)(b) (Amendment No-1)(Shrinkage at 100 °C ± 1 °C for 1 h for rubber, percent, Max)	-	-	-
Cl-4.4, Table -1 S. No-1 (iv) (Amendment No-1)(Abrasion resistance at applied force)	-	-	-
Cl-4.4, Table -1 S. No-1 (v) (Amendment No-1)(Flexing resistance: Maximum cut growth,)	-	-	-
Cl-4.4, Table -1 S. No-1 (vi) (Amendment No-1)(Hydrolysis resistance:Maximum cut growth)	-	-	-
Cl-4.4, Table -2 S. No-1 (i), a (Amendment No-1)("Breaking strength for Strap to strap 1-Solid strap 2-Cellular strap")	-	-	-
Cl-4.4, Table -2 S. No-1 (i), b (Amendment No-1)("Breaking strength for Toe portion to strap 1-Solid strap 2-Cellular strap")	-	-	-
Cl-4.4, Table -2 S. No-1 (i), c (Amendment No-1)("Elongation at break , percent, Min 1-Solid strap 2-Cellular strap")	-	-	-
Cl-4.4, Table -3 S. No-1 (i), (Amendment No-1)(Toe post attachment strength)	-	-	-
Cl-4.4, Table -3 S. No-1 (ii), (Amendment No-1)(Attachment strength of rear strap)	-	-	-
Cl-4.4, Table -3 S. No-1 (iii), (Amendment No-1)(Inter layer bond strength)	-	-	-

02 Sep, 2027

-
Exclusion: Table 1 vii and Table 2 ii Chemical requirements, Table 1 viii and Table 2 iii Lead content

4310

Bahadurgarh Footwear Development Services (BFDS), Bahadurgarh

8168806

IS 15844 : Part 1 (2023)

SPORTS FOOTWEAR PART -1 GENERAL PURPOSEFirst Revision

22000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl No.4.1(Sampling and Conditioning)	-	500	-
Cl No.4.2(Construction)	-	300	-
Cl No.4.3(Whole Footwear)	-	300	-
4.3.1(Insole)	-	300	-
4.3.2(Toe spring height)	-	500	-
4.3.3(Upper to Mid Sole/Out Sole Bond Performance)	-	500	-
4.3.4("Upper to Composite Sole Bond Performance (Applicable Only When the Sole is Composite)")	-	500	-
4.3.5(Out Sole to Mid Sole (Multilayer) Bond Performance)	-	500	-
4.3.6(Energy Absorption at Seat Region)	-	800	-
4.3.7(Complete Shoe Flexing)	-	640	-
4.3.8(Washability)	-	800	-
4.3.9(Slip Resistance)	-	1000	-
Cl No.4.4 , Table No. 2 , i) , a)(Flexing resistance, Dry condition)	-	600	-
Cl No.4.4 , Table No. 2 , ii)(Tear strength (average force), Min, N)	-	450	-
Cl No.4.4 , Table No. 2 , iii) , a)("Colour fastness rubbing (To and fro) Grey scale rate, Min , Dry: (rubbing) Rating: (Marring and staining) ")	-	600	-
Cl No.4.4 , Table No. 2 , iii) , b)("Colour fastness rubbing (To and fro) Grey scale rate, Min , Wet: (rubbing) Rating: (Marring and staining)")	-	600	-
Cl No.4.4 , Table No. 2 , iv) , a)(Water vapour permeability, mg/cm2h, Min)	-	800	-
Cl No.4.4 , Table No. 2 , iv) , b)(Water vapour coefficient, mg/cm2 , Min)	-	800	-
Cl No.4.4 , Table No. 2 , v)(Stitch tear strength (double hole), N/mm, Min)	-	600	-
Cl No.4.4 , Table No. 2 , i)(Breaking strength, N/mm, Min)	-	450	-
Cl No.4.4 , Table No. 2 , ii)(Elongation at break, percent Min)	-	450	-
Cl No.4.4 , Table No. 2 , iii)(Tear strength, N, Min For Fabric: For all other materials)	-	450	-
Cl No.4.4 , Table No. 2 , iv) , a)(Flexing resistance, Dry condition)	-	600	-
Cl No.4.4 , Table No. 2 , iv) , b)(Flexing resistance, ,Wet condition)	-	600	-
Cl No.4.4 , Table No. 2 , v) , a)(Water vapour permeability, mg/cm2h, Min)	-	800	-
Cl No.4.4 , Table No. 2 , v) , b)("Water vapour coefficient, mg/cm2 , Min ")	-	800	-
Cl No.4.4 , Table No. 2 , vi)(Hydrolysis resistance)	-	2000	-
Cl No.4.4 , Table No. 2 , vii)(Bursting Strength, kg/cm2 , Min)	-	500	-
Cl No.4.5 , Table No. 3 , i)(Tear strength, N, Min)	-	450	-
Cl No.4.5 , Table No. 3 , ii)(Abrasion resistance, cycles)	-	600	-
Cl No.4.5 , Table No. 3 , iii)("Colour fastness to rubbing (crocking), Grey scale rate with 10 rubs on dry or wet, Min")	-	600	-
Cl No.4.5 , Table No. 3 , iv)("Colour fastness to perspiration (contact method) Grey scale rate, Min")	-	600	-
Cl No.4.5 , Table No. 3 , v) , a)(Water vapour permeability, mg/cm2h, Min)	-	800	-
Cl No.4.5 , Table No. 3 , v) , b)("Water vapour coefficient, mg/cm2 , Min ")	-	800	-
Cl No.4.6 , Table No. 4 , i)(Thickness, mm, Min)	-	200	-
Cl No.4.6 , Table No. 4 , ii)(Flexing index, Min)	-	800	-
Cl No.4.6 , Table No. 4 , iii)(Abrasion resistance, at 400 cycles)	-	800	-
Cl No.4.6 , Table No. 4 , iv) , a)(Water Absorption, mg/cm2 , Min)	-	800	-
Cl No.4.6 , Table No. 4 , iv) , b)(Water Desorption, percent, Min)	-	800	-
Cl No.4.7, Table No. 5 , i)(Thickness, mm, Min)	-	200	-
Cl No.4.7, Table No. 5 , ii)(Abrasion resistance, cycles)	-	600	-
Cl No.4.7, Table No. 5 , iii) , a)(Water Absorption, mg/cm2 , Min)	-	800	-
Cl No.4.7, Table No. 5 , iii) , b)(Water Desorption, percent, Min)	-	800	-
Cl No.4.8 , Table No. 6 , i)(Abrasion resistance (Volume loss), mm3 , Max)	-	600	-
Cl No.4.8 , Table No. 6 , ii)("Flexing resistance Belt Method at 90 diameter Mandrel or Bennewart method, cut growth, Max")	-	600	-
Cl No.4.8 , Table No. 6 , iii)("Hydrolysis resistance, cut growth after 150 000 flexes, in mm, Max")	-	2000	-
Cl No.4.9 , Table No. 7 , i)(Compression set, percent, Max)	-	500	-
Cl No.4.9 , Table No. 7 , ii)(Split tear strength, kg/25 mm, Min)	-	450	-
Cl No.4.9 , Table No. 7 , iii)(Heat shrinkage, percent, Max)	-	800	-
Cl No.4.10 , Table No. 8 , i)(First dry collapsing load, hardness, N, Min)	-	800	-
Cl No.4.10 , Table No. 8 , ii)(Resilience, percent, Min)	-	800	-
Cl No.4.10 , Table No. 8 , iii)(Moisture resistance, percent, Min)	-	800	-
Cl No.4.10 , Table No. 8 , iv) , a)(Initial dry area shape retention, percent, Min)	-	800	-
Cl No.4.10 , Table No. 8 , iv) , b)(Area shape retention after 10th collapse, dry, percent, Min)	-	800	-
Cl No.4.11 , Table No. 9 , i)(Peel strength, N/mm, Min)	-	500	-
Cl No.4.11 , Table No. 9 , ii)(Shear strength, kPa , Min)	-	600	-
Cl No.4.12 , Table No. 10 , i)(Limit of useful extension, percent, Min)	-	600	-
Cl No.4.13 , Table No. 11 , i)(Breaking strength of lace, N, Min)	-	500	-
Cl No.4.13 , Table No. 11 , ii)(Lace tag strength, N, Min)	-	500	-
Cl No.4.13 , Table No. 11 , iii)(Lace to lace abrasion,)	-	800	-
Cl No.4.13 , Table No. 11 , iv)("Colour fastness to water Gray Scale Rate, Min Rating")	-	600	-
Cl No.4.13 , Table No. 11 , v)(Strength of Buckle/Ski hook, N, Min)	-	600	-
Cl No.4.13 , Table No. 11 , vi)(Corrosion resistance)	-	600	-
Cl No . 5(MARKING AND PACKING)	-	1000	-
Cl No . 4.14, Table no. 1 of IS 17011(iv)(Chromium (VI))	-	600	-
Cl No . 4.14, Table no. 1 of IS 17011(x)(pH)	-	400	-
Clause 4.2 - 4.2.1(Construction)	-	200	-
Clause 4.2 - 4.2.2(Construction)	-	200	-
Clause 4.3 - 4.3.1(Whole Footwear)	-	200	-
Clause 4.3 - 4.3.2(Whole Footwear)	-	200	-
Clause 4.3 - 4.3.3(Upper to Mid Sole/Out Sole Bond Performance)	-	500	-
Clause 4.3 - 4.3.4(Upper to Composite Sole Bond Performance(Applicable Only When the Sole is Composite))	-	500	-
Clause 4.3 - 4.3.5(Out Sole to Mid Sole (Multilayer) Bond)	-	500	-
Clause 4.3 - 4.3.7(Complete Shoe Flexing)	-	640	-
Clause 4.4, Table 1 ii)(Tear strength)	-	450	-
Clause 4.4, Table 1 iv)-a(Water Vapour Permeability)	-	800	-
Clause 4.5, Table 3 v)-b(Water Vapour Coeffecient)	-	800	-
Clause 4.4, Table 1 v)(Stitch Tear Strength(Double Hole))	-	600	-
Clause 4.4, Table 2 i)(Breaking Strength)	-	450	-
Clause 4.4, Table 2 ii)(Elongation at break)	-	450	-
Clause 4.4, Table 2 iii)(Tear strength)	-	450	-
Clause 4.4, Table 2 v)-a(Water Vapour Permeability)	-	800	-
Clause 4.4, Table 2 v)-b(Water Vapour Coeffecient)	-	800	-
Clause 4.5, Table 3 i)(Tear strength)	-	450	-
Clause 4.5, Table 3 ii)(Abrasion Resistance)	-	600	-
Clause 4.5, Table 3 v)-a(Water Vapour Permeability)	-	800	-
Clause 4.6, Table 4 i)(Thickness)	-	200	-
Clause 4.6, Table 4 ii)(Abrasion Resistance)	-	600	-
Clause 4.6, Table 4 iv)-a(Water Absorption)	-	800	-
Clause 4.6, Table 4 iv)-b(Water Desorption)	-	800	-
Clause 4.8, Table 6 i)(Abrasion Resistance)	-	600	-
Clause 4.8, Table 6 ii)(Flexing Resistance)	-	600	-
Clause 4.8, Table 6 iii)(Hydrolysis Resistance)	-	2000	-
Clause 4.9, Table 7 ii)(Split Tear strength)	-	450	-
Clause 4.9, Table 7 iii)(Heat shrinkage)	-	800	-
Clause 4.4, Table 1 iv)-b(Water Vapour Coeffecient)	-	800	-
Clause 4.7, Table 5 i)(Thickness)	-	200	-
Clause 4.7, Table 5 iii)-a(Water Absorption)	-	800	-
Cl No.4.4 , Table No. 2 , i) , b)(Flexing resistance, Wet condition)	-	600	-
Clause 4.7, Table 5 ii)(Abrasion Resistance)	-	600	-
Clause 4.7, Table 5 iii)-b(Water Desorption)	-	800	-
Cl No.4.1(Sampling and Conditioning)	-	200	-
Cl No.4.2(Construction)	-	200	-
Cl No.4.3(Whole Footwear)	-	200	-
4.3.1(Insole)	-	200	-
4.3.2(Toe spring height)	-	200	-
4.3.3(Upper to Mid Sole/Out Sole Bond Performance)	-	500	-
4.3.4("Upper to Composite Sole Bond Performance (Applicable Only When the Sole is Composite)")	-	500	-
4.3.5(Out Sole to Mid Sole (Multilayer) Bond Performance)	-	500	-
4.3.6(Energy Absorption at Seat Region)	-	800	-
4.3.7(Complete Shoe Flexing)	-	640	-
4.3.9(Slip Resistance)	-	1500	-
Cl No.4.4 , Table No. 2 , i) , a)(Flexing resistance, Dry condition)	-	600	-
Cl No.4.4 , Table No. 2 , ii)(Tear strength (average force), Min, N)	-	450	-
Cl No.4.4 , Table No. 2 , iii) , a)("Colour fastness rubbing (To and fro) Grey scale rate, Min , Dry: (rubbing) Rating: (Marring and staining) ")	-	500	-
Cl No.4.4 , Table No. 2 , iii) , b)("Colour fastness rubbing (To and fro) Grey scale rate, Min , Wet: (rubbing) Rating: (Marring and staining)")	-	500	-
Cl No.4.4 , Table No. 2 , iv) , a)(Water vapour permeability, mg/cm2h, Min)	-	800	-
Cl No.4.4 , Table No. 2 , iv) , b)(Water vapour coefficient, mg/cm2 , Min)	-	800	-
Cl No.4.4 , Table No. 2 , v)(Stitch tear strength (double hole), N/mm, Min)	-	450	-
Cl No.4.4 , Table No. 2 , i)(Breaking strength, N/mm, Min)	-	450	-
Cl No.4.4 , Table No. 2 , ii)(Elongation at break, percent Min)	-	450	-
Cl No.4.4 , Table No. 2 , iii)(Tear strength, N, Min For Fabric: For all other materials)	-	450	-
Cl No.4.4 , Table No. 2 , iv) , a)(Flexing resistance, Dry condition)	-	600	-
Cl No.4.4 , Table No. 2 , iv) , b)(Flexing resistance, ,Wet condition)	-	600	-
Cl No.4.4 , Table No. 2 , v) , a)(Water vapour permeability, mg/cm2h, Min)	-	800	-
Cl No.4.4 , Table No. 2 , v) , b)("Water vapour coefficient, mg/cm2 , Min ")	-	800	-
Cl No.4.4 , Table No. 2 , vi)(Hydrolysis resistance)	-	2500	-
Cl No.4.4 , Table No. 2 , vii)(Bursting Strength, kg/cm2 , Min)	-	600	-
Cl No.4.5 , Table No. 3 , i)(Tear strength, N, Min)	-	450	-
Cl No.4.5 , Table No. 3 , ii)(Abrasion resistance, cycles)	-	600	-
Cl No.4.5 , Table No. 3 , iii)("Colour fastness to rubbing (crocking), Grey scale rate with 10 rubs on dry or wet, Min")	-	500	-
Cl No.4.5 , Table No. 3 , iv)("Colour fastness to perspiration (contact method) Grey scale rate, Min")	-	500	-
Cl No.4.5 , Table No. 3 , v) , a)(Water vapour permeability, mg/cm2h, Min)	-	800	-
Cl No.4.5 , Table No. 3 , v) , b)("Water vapour coefficient, mg/cm2 , Min ")	-	800	-
Cl No.4.6 , Table No. 4 , i)(Thickness, mm, Min)	-	200	-
Cl No.4.6 , Table No. 4 , ii)(Flexing index, Min)	-	600	-
Cl No.4.6 , Table No. 4 , iii)(Abrasion resistance, at 400 cycles)	-	600	-
Cl No.4.6 , Table No. 4 , iv) , a)(Water Absorption, mg/cm2 , Min)	-	800	-
Cl No.4.6 , Table No. 4 , iv) , b)(Water Desorption, percent, Min)	-	800	-
Cl No.4.7, Table No. 5 , i)(Thickness, mm, Min)	-	200	-
Cl No.4.7, Table No. 5 , ii)(Abrasion resistance, cycles)	-	800	-
Cl No.4.7, Table No. 5 , iii) , a)(Water Absorption, mg/cm2 , Min)	-	800	-
Cl No.4.7, Table No. 5 , iii) , b)(Water Desorption, percent, Min)	-	800	-
Cl No.4.8 , Table No. 6 , i)(Abrasion resistance (Volume loss), mm3 , Max)	-	600	-
Cl No.4.8 , Table No. 6 , ii)("Flexing resistance Belt Method at 90 diameter Mandrel or Bennewart method, cut growth, Max")	-	600	-
Cl No.4.8 , Table No. 6 , iii)("Hydrolysis resistance, cut growth after 150 000 flexes, in mm, Max")	-	2500	-
Cl No.4.9 , Table No. 7 , i)(Compression set, percent, Max)	-	500	-
Cl No.4.9 , Table No. 7 , ii)(Split tear strength, kg/25 mm, Min)	-	450	-
Cl No.4.9 , Table No. 7 , iii)(Heat shrinkage, percent, Max)	-	800	-
Cl No.4.10 , Table No. 8 , i)(First dry collapsing load, hardness, N, Min)	-	800	-
Cl No.4.10 , Table No. 8 , ii)(Resilience, percent, Min)	-	800	-
Cl No.4.10 , Table No. 8 , iii)(Moisture resistance, percent, Min)	-	800	-
Cl No.4.10 , Table No. 8 , iv) , a)(Initial dry area shape retention, percent, Min)	-	800	-
Cl No.4.10 , Table No. 8 , iv) , b)(Area shape retention after 10th collapse, dry, percent, Min)	-	800	-
Cl No.4.11 , Table No. 9 , i)(Peel strength, N/mm, Min)	-	500	-
Cl No.4.11 , Table No. 9 , ii)(Shear strength, kPa , Min)	-	600	-
Cl No.4.12 , Table No. 10 , i)(Limit of useful extension, percent, Min)	-	800	-
Cl No.4.13 , Table No. 11 , i)(Breaking strength of lace, N, Min)	-	500	-
Cl No.4.13 , Table No. 11 , ii)(Lace tag strength, N, Min)	-	500	-
Cl No.4.13 , Table No. 11 , iii)(Lace to lace abrasion,)	-	800	-
Cl No.4.13 , Table No. 11 , iv)("Colour fastness to water Gray Scale Rate, Min Rating")	-	600	-
Cl No.4.13 , Table No. 11 , v)(Strength of Buckle/Ski hook, N, Min)	-	500	-
Cl No.4.13 , Table No. 11 , vi)(Corrosion resistance)	-	600	-
Cl No . 5(MARKING AND PACKING)	-	500	-
Cl No . 4.14, Table no. 1 of IS 17011(iv)(Chromium (VI))	-	800	-
Cl No . 4.14, Table no. 1 of IS 17011(x)(pH)	-	500	-
Clause 4.2 - 4.2.1(Construction)	-	200	-
Clause 4.2 - 4.2.2(Construction)	-	200	-
Clause 4.3 - 4.3.1(Whole Footwear)	-	500	-
Clause 4.3 - 4.3.2(Whole Footwear)	-	500	-
Clause 4.3 - 4.3.3(Upper to Mid Sole/Out Sole Bond Performance)	-	500	-
Clause 4.3 - 4.3.4(Upper to Composite Sole Bond Performance(Applicable Only When the Sole is Composite))	-	500	-
Clause 4.3 - 4.3.5(Out Sole to Mid Sole (Multilayer) Bond)	-	500	-
Clause 4.3 - 4.3.7(Complete Shoe Flexing)	-	640	-
Clause 4.4, Table 1 ii)(Tear strength)	-	450	-
Clause 4.4, Table 1 iv)-a(Water Vapour Permeability)	-	800	-
Clause 4.5, Table 3 v)-b(Water Vapour Coeffecient)	-	800	-
Clause 4.4, Table 1 v)(Stitch Tear Strength(Double Hole))	-	450	-
Clause 4.4, Table 2 i)(Breaking Strength)	-	450	-
Clause 4.4, Table 2 ii)(Elongation at break)	-	450	-
Clause 4.4, Table 2 iii)(Tear strength)	-	450	-
Clause 4.4, Table 2 v)-a(Water Vapour Permeability)	-	800	-
Clause 4.4, Table 2 v)-b(Water Vapour Coeffecient)	-	800	-
Clause 4.5, Table 3 i)(Tear strength)	-	450	-
Clause 4.5, Table 3 ii)(Abrasion Resistance)	-	600	-
Clause 4.5, Table 3 v)-a(Water Vapour Permeability)	-	800	-
Clause 4.6, Table 4 i)(Thickness)	-	200	-
Clause 4.6, Table 4 ii)(Abrasion Resistance)	-	600	-
Clause 4.6, Table 4 iv)-a(Water Absorption)	-	800	-
Clause 4.6, Table 4 iv)-b(Water Desorption)	-	800	-
Clause 4.8, Table 6 i)(Abrasion Resistance)	-	600	-
Clause 4.8, Table 6 ii)(Flexing Resistance)	-	600	-
Clause 4.8, Table 6 iii)(Hydrolysis Resistance)	-	2500	-
Clause 4.9, Table 7 ii)(Split Tear strength)	-	450	-
Clause 4.9, Table 7 iii)(Heat shrinkage)	-	800	-
Clause 4.4, Table 1 iv)-b(Water Vapour Coeffecient)	-	800	-
Clause 4.7, Table 5 i)(Thickness)	-	200	-
Clause 4.7, Table 5 iii)-a(Water Absorption)	-	800	-
Cl No.4.4 , Table No. 2 , i) , b)(Flexing resistance, Wet condition)	-	600	-
Clause 4.7, Table 5 ii)(Abrasion Resistance)	-	800	-
Clause 4.7, Table 5 iii)-b(Water Desorption)	-	800	-
Cl-5, Table -1 S. No-(i) (Amendment No-1)(Insole)	-	200	-
Cl-5, Table -1 S. No- (ii) (Amendment No-1)(Toe spring height)	-	200	-
Cl-5, Table -1 S. No- (iii) (Amendment No-1)("Bond performance (a) Upper to sole/mid sole/composite sole (b) Interlayer bond strength")	-	500	-
Cl-5, Table -1 S. No- (iv) (Amendment No-1)(Energy absorption at seat region)	-	800	-
Cl-5, Table -1 S. No- (v) (Amendment No-1)(Complete shoe flexing)	-	640	-
Cl-5, Table -1 S. No-(vi) (Amendment No-1)(Washability)	-	800	-
Cl-5, Table -1 S. No- (vii) (Amendment No-1)(Slip resistance, coefficient of friction (COF),)	-	1500	-
Cl-5, Table -1 S. No- (viii) (Amendment No-1)("Abrasion resistance a-Cellular sole b-Solid sole")	-	600	-
Cl-5, Table -1 S. No- (xi) (Amendment No-1)(Hydrolysis resistance)	-	2500	-
Cl-6, Table -2 S. No- (i) (Amendment No-1)(Tear strength)	-	450	-
Cl-6, Table -2 S. No- (ii) (Amendment No-1)("Colour fastness rubbing a-Dry: (rubbing) b-Wet: (rubbing)")	-	500	-
Cl-6, Table -2 S. No- (iii), a) (Amendment No-1)(Water vapour permeability)	-	800	-
Cl-6, Table -2 S. No- (iii), b) (Amendment No-1)(Water vapour coefficient)	-	800	-
Cl-6, Table -2 S. No- (iv),(Amendment No-1)(Stitch tear strength)	-	450	-
Cl-6, Table -3 S. No- (i),(Amendment No-1)(Breaking strength, N/mm, Min)	-	500	-
Cl-6, Table -3 S. No- (ii),(Amendment No-1)("Elongation at break a-Tighter direction b-Stretch direction")	-	450	-
Cl-6, Table -3 S. No- (iii),(Amendment No-1)("Tear strength, N, Min a) For fabric b) For all other materials")	-	450	-
Cl-6, Table -3 S. No- (iv),(Amendment No-1)("Flexing resistance a- Dry condition b-Wet condition")	-	600	-
Cl-6, Table -3 S. No- (v), a (Amendment No-1)(Water vapour permeability)	-	800	-
Cl-6, Table -3 S. No- (v), b (Amendment No-1)(Water vapour coefficient)	-	800	-
Cl-6, Table -3 S. No- (vi), (Amendment No-1)(Hydrolysis resistance)	-	2500	-
Cl-6, Table -3 S. No- (vii), (Amendment No-1)(Bursting strength)	-	800	-
Cl-6, Table -4 S. No- (ii),(Amendment No-1)("Abrasion resistance, cycles a- Dry condition b-Wet condition")	-	600	-
Cl-6, Table -4 S. No- (iii),(Amendment No-1)(Colour fastness to rubbing , grey scale rate with 10 rubs on dry or wet, Min)	-	500	-
Cl-6, Table -4 S. No- (iv),(Amendment No-1)(Colour fastness to perspiration)	-	800	-
Cl-6, Table -4 S. No- (v), a (Amendment No-1)(Water vapour permeability)	-	800	-
Cl-6, Table -4 S. No- (v), b (Amendment No-1)(Water vapour coefficient)	-	800	-
Cl-6, Table -5 S. No- (i), (Amendment No-1)(Thickness, mm, Min)	-	200	-
Cl-6, Table -5 S. No-(ii), (Amendment No-1)(Flexing index, Min)	-	640	-
Cl-6, Table -5 S. No-(iii), (Amendment No-1)(Abrasion resistance,)	-	600	-
Cl-6, Table -5 S. No- (iv), a (Amendment No-1)(Water absorption)	-	800	-
Cl-6, Table -5 S. No- (iv), b (Amendment No-1)(Water desorption, percent)	-	800	-
Cl-6, Table -6 S. No- (i), (Amendment No-1)(Thickness, mm, Min)	-	200	-
Cl-6, Table -6 S. No- (ii), (Amendment No-1)("Abrasion resistance, cycles a- Dry condition b-Wet condition")	-	600	-
Cl-6, Table -6 S. No- (iii),a (Amendment No-1)(Water absorption)	-	800	-
Cl-6, Table -6 S. No- (iv), b (Amendment No-1)(Water desorption, percent)	-	800	-
Cl-6, Table -7 S. No- (i), (Amendment No-1)(Flexing resistance (Belt method or Bennewart method))	-	600	-
Cl-6, Table -7 S. No- (ii), (Amendment No-1)(Hydrolysis resistance, cut growth after flexes)	-	2500	-
Cl-6, Table -8 S. No- (i), (Amendment No-1)("Compression set, percent, Max a) For EVA b) For all other materials")	-	500	-
Cl-6, Table -8 S. No- (ii), (Amendment No-1)(Split tear strength)	-	450	-
Cl-6, Table -8 S. No- (iii), (Amendment No-1)(Heat shrinkage)	-	800	-
Cl-6, Table -9 S. No- (i), (Amendment No-1)(First dry collapsing load, hardness)	-	800	-
Cl-6, Table -9 S. No- (ii), (Amendment No-1)(Resilience, percent)	-	800	-
Cl-6, Table -9 S. No- (iii), (Amendment No-1)(Moisture resistance)	-	800	-
Cl-6, Table -9 S. No- (iv), a (Amendment No-1)(Initial dry area shape retention)	-	800	-
Cl-6, Table -9 S. No- (iv), b (Amendment No-1)(Area shape retention after 10th collapse)	-	800	-
Cl-6, Table -10 S. No- (i), (Amendment No-1)("Peel strength a) Initial b) After 5 000 wear cycles")	-	500	-
Cl-6, Table -10 S. No- (ii), (Amendment No-1)("Shear strength a) Initial b) After 5 000 wear cycles")	-	500	-
Cl-6, Table -11 S. No- (i), (Amendment No-1)(Limit of useful extension)	-	800	-
Cl-6, Table -12 S. No- (i), (Amendment No-1)(Breaking strength of lace)	-	500	-
Cl-6, Table -12 S. No- (ii), (Amendment No-1)(Lace tag strength)	-	500	-
Cl-6, Table -12 S. No- (iii), (Amendment No-1)(Lace to lace abrasion)	-	800	-
Cl-6, Table -12 S. No- (iv), (Amendment No-1)(Colour fastness to water (for lace) (contact method))	-	500	-
Cl-6, Table -12 S. No- (iv), (Amendment No-1)(Colour fastness to water (for lace) (contact method))	-	500	-
Cl-6, Table -12 S. No (v), (Amendment No-1)(Strength of buckle/ski hook)	-	500	-
Cl-6, Table -12 S. No- (vi), (Amendment No-1)(Corrosion resistance)	-	600	-
Cl-6, Table -4 S. No- (i),(Amendment No-1)(Tear strength, N, Min)	-	450	-
Cl No.4.1(Sampling and Conditioning)	-	500	-
Cl No.4.2(Construction)	-	300	-
Cl No.4.3(Whole Footwear)	-	300	-
4.3.1(Insole)	-	300	-
4.3.2(Toe spring height)	-	500	-
Cl No.4.4 , Table No. 2 , i)(Breaking strength, N/mm, Min)	-	500	-
Cl No.4.4 , Table No. 2 , vii)(Bursting Strength, kg/cm2 , Min)	-	500	-
Cl No.4.7, Table No. 5 , ii)(Abrasion resistance, cycles)	-	600	-
Cl No.4.10 , Table No. 8 , ii)(Resilience, percent, Min)	-	500	-
Cl No.4.11 , Table No. 9 , ii)(Shear strength, kPa , Min)	-	800	-
Cl No.4.13 , Table No. 11 , iv)("Colour fastness to water Gray Scale Rate, Min Rating")	-	500	-
Cl No . 5(MARKING AND PACKING)	-	600	-
Clause 4.2 - 4.2.1(Construction)	-	500	-
Clause 4.2 - 4.2.2(Construction)	-	500	-
Clause 4.3 - 4.3.1(Whole Footwear)	-	600	-
Clause 4.3 - 4.3.2(Whole Footwear)	-	600	-
Clause 4.4, Table 2 i)(Breaking Strength)	-	500	-
Clause 4.9, Table 7 iii)(Heat shrinkage)	-	2000	-
Clause 4.7, Table 5 ii)(Abrasion Resistance)	-	600	-
Cl-5, Table -1 S. No-(i) (Amendment No-1)(Insole)	-	500	-
Cl-5, Table -1 S. No- (ii) (Amendment No-1)(Toe spring height)	-	500	-
Cl-5, Table -1 S. No- (iii) (Amendment No-1)("Bond performance (a) Upper to sole/mid sole/composite sole (b) Interlayer bond strength")	-	500	-
Cl-5, Table -1 S. No- (iv) (Amendment No-1)(Energy absorption at seat region)	-	800	-
Cl-5, Table -1 S. No- (v) (Amendment No-1)(Complete shoe flexing)	-	600	-
Cl-5, Table -1 S. No- (vii) (Amendment No-1)(Slip resistance, coefficient of friction (COF),)	-	1500	-
Cl-5, Table -1 S. No- (viii) (Amendment No-1)("Abrasion resistance a-Cellular sole b-Solid sole")	-	600	-
Cl-5, Table -1 S. No- (xi) (Amendment No-1)(Hydrolysis resistance)	-	2500	-
Cl-6, Table -2 S. No- (i) (Amendment No-1)(Tear strength)	-	450	-
Cl-6, Table -2 S. No- (ii) (Amendment No-1)("Colour fastness rubbing a-Dry: (rubbing) b-Wet: (rubbing)")	-	500	-
Cl-6, Table -2 S. No- (iii), a) (Amendment No-1)(Water vapour permeability)	-	800	-
Cl-6, Table -2 S. No- (iii), b) (Amendment No-1)(Water vapour coefficient)	-	800	-
Cl-6, Table -2 S. No- (iv),(Amendment No-1)(Stitch tear strength)	-	450	-
Cl-6, Table -3 S. No- (i),(Amendment No-1)(Breaking strength, N/mm, Min)	-	500	-
Cl-6, Table -3 S. No- (ii),(Amendment No-1)("Elongation at break a-Tighter direction b-Stretch direction")	-	450	-
Cl-6, Table -3 S. No- (iii),(Amendment No-1)("Tear strength, N, Min a) For fabric b) For all other materials")	-	450	-
Cl-6, Table -3 S. No- (iv),(Amendment No-1)("Flexing resistance a- Dry condition b-Wet condition")	-	600	-
Cl-6, Table -3 S. No- (v), a (Amendment No-1)(Water vapour permeability)	-	800	-
Cl-6, Table -3 S. No- (v), b (Amendment No-1)(Water vapour coefficient)	-	800	-
Cl-6, Table -3 S. No- (vi), (Amendment No-1)(Hydrolysis resistance)	-	2500	-
Cl-6, Table -3 S. No- (vii), (Amendment No-1)(Bursting strength)	-	600	-
Cl-6, Table -4 S. No- (ii),(Amendment No-1)("Abrasion resistance, cycles a- Dry condition b-Wet condition")	-	600	-
Cl-6, Table -4 S. No- (iii),(Amendment No-1)(Colour fastness to rubbing , grey scale rate with 10 rubs on dry or wet, Min)	-	500	-
Cl-6, Table -4 S. No- (iv),(Amendment No-1)(Colour fastness to perspiration)	-	600	-
Cl-6, Table -4 S. No- (v), a (Amendment No-1)(Water vapour permeability)	-	800	-
Cl-6, Table -4 S. No- (v), b (Amendment No-1)(Water vapour coefficient)	-	800	-
Cl-6, Table -5 S. No- (i), (Amendment No-1)(Thickness, mm, Min)	-	200	-
Cl-6, Table -5 S. No-(ii), (Amendment No-1)(Flexing index, Min)	-	600	-
Cl-6, Table -5 S. No-(iii), (Amendment No-1)(Abrasion resistance,)	-	600	-
Cl-6, Table -5 S. No- (iv), a (Amendment No-1)(Water absorption)	-	800	-
Cl-6, Table -5 S. No- (iv), b (Amendment No-1)(Water desorption, percent)	-	800	-
Cl-6, Table -6 S. No- (i), (Amendment No-1)(Thickness, mm, Min)	-	200	-
Cl-6, Table -6 S. No- (ii), (Amendment No-1)("Abrasion resistance, cycles a- Dry condition b-Wet condition")	-	600	-
Cl-6, Table -6 S. No- (iii),a (Amendment No-1)(Water absorption)	-	800	-
Cl-6, Table -6 S. No- (iv), b (Amendment No-1)(Water desorption, percent)	-	800	-
Cl-6, Table -7 S. No- (i), (Amendment No-1)(Flexing resistance (Belt method or Bennewart method))	-	600	-
Cl-6, Table -7 S. No- (ii), (Amendment No-1)(Hydrolysis resistance, cut growth after flexes)	-	2500	-
Cl-6, Table -8 S. No- (i), (Amendment No-1)("Compression set, percent, Max a) For EVA b) For all other materials")	-	500	-
Cl-6, Table -8 S. No- (ii), (Amendment No-1)(Split tear strength)	-	450	-
Cl-6, Table -8 S. No- (iii), (Amendment No-1)(Heat shrinkage)	-	800	-
Cl-6, Table -9 S. No- (i), (Amendment No-1)(First dry collapsing load, hardness)	-	800	-
Cl-6, Table -9 S. No- (ii), (Amendment No-1)(Resilience, percent)	-	800	-
Cl-6, Table -9 S. No- (iii), (Amendment No-1)(Moisture resistance)	-	800	-
Cl-6, Table -9 S. No- (iv), a (Amendment No-1)(Initial dry area shape retention)	-	800	-
Cl-6, Table -9 S. No- (iv), b (Amendment No-1)(Area shape retention after 10th collapse)	-	800	-
Cl-6, Table -10 S. No- (i), (Amendment No-1)("Peel strength a) Initial b) After 5 000 wear cycles")	-	500	-
Cl-6, Table -10 S. No- (ii), (Amendment No-1)("Shear strength a) Initial b) After 5 000 wear cycles")	-	800	-
Cl-6, Table -11 S. No- (i), (Amendment No-1)(Limit of useful extension)	-	800	-
Cl-6, Table -12 S. No- (i), (Amendment No-1)(Breaking strength of lace)	-	500	-
Cl-6, Table -12 S. No- (ii), (Amendment No-1)(Lace tag strength)	-	500	-
Cl-6, Table -12 S. No- (iii), (Amendment No-1)(Lace to lace abrasion)	-	600	-
Cl-6, Table -12 S. No (v), (Amendment No-1)(Strength of buckle/ski hook)	-	500	-
Cl-6, Table -12 S. No- (vi), (Amendment No-1)(Corrosion resistance)	-	800	-
Cl-6, Table -4 S. No- (i),(Amendment No-1)(Tear strength, N, Min)	-	450	-
Cl-6, Table -12 S. No- (iv), (Amendment No-1)(Colour fastness to water (for lace) (contact method))	-	600	-
Cl-6, Table -12 S. No- (iv), (Amendment No-1)(Colour fastness to water (for lace) (contact method))	-	600	-
Cl No.4.3(Whole Footwear)	-	640	-
Cl No.4.4 , Table No. 2 , v)(Stitch tear strength (double hole), N/mm, Min)	-	600	-
Cl No.4.5 , Table No. 3 , iv)("Colour fastness to perspiration (contact method) Grey scale rate, Min")	-	600	-
Cl No.4.6 , Table No. 4 , iii)(Abrasion resistance, at 400 cycles)	-	500	-
Cl No.4.9 , Table No. 7 , iii)(Heat shrinkage, percent, Max)	-	1200	-
Cl No.4.10 , Table No. 8 , ii)(Resilience, percent, Min)	-	400	-
Cl No.4.10 , Table No. 8 , iii)(Moisture resistance, percent, Min)	-	600	-
Cl No.4.12 , Table No. 10 , i)(Limit of useful extension, percent, Min)	-	600	-
Cl No.4.13 , Table No. 11 , i)(Breaking strength of lace, N, Min)	-	450	-
Cl No.4.13 , Table No. 11 , iii)(Lace to lace abrasion,)	-	600	-
Cl No . 5(MARKING AND PACKING)	-	200	-
Clause 4.3 - 4.3.1(Whole Footwear)	-	640	-
Clause 4.3 - 4.3.2(Whole Footwear)	-	640	-
Clause 4.4, Table 1 v)(Stitch Tear Strength(Double Hole))	-	600	-
Clause 4.9, Table 7 iii)(Heat shrinkage)	-	1200	-
Cl No.4.4 , Table No. 2 , i) , b)(Flexing resistance, Wet condition)	-	800	-
Cl-5, Table -1 S. No-(i) (Amendment No-1)(Insole)	-	200	-
Cl-5, Table -1 S. No- (ii) (Amendment No-1)(Toe spring height)	-	200	-
Cl-5, Table -1 S. No- (v) (Amendment No-1)(Complete shoe flexing)	-	640	-
Cl-6, Table -2 S. No- (iv),(Amendment No-1)(Stitch tear strength)	-	600	-
Cl-6, Table -4 S. No- (iii),(Amendment No-1)(Colour fastness to rubbing , grey scale rate with 10 rubs on dry or wet, Min)	-	600	-
Cl-6, Table -8 S. No- (iii), (Amendment No-1)(Heat shrinkage)	-	1200	-
Cl-6, Table -10 S. No- (ii), (Amendment No-1)("Shear strength a) Initial b) After 5 000 wear cycles")	-	600	-
Cl-6, Table -12 S. No- (i), (Amendment No-1)(Breaking strength of lace)	-	450	-
Cl-6, Table -12 S. No- (vi), (Amendment No-1)(Corrosion resistance)	-	600	-
Cl-6, Table -12 S. No- (iv), (Amendment No-1)(Colour fastness to water (for lace) (contact method))	-	500	-
Cl-6, Table -12 S. No- (iv), (Amendment No-1)(Colour fastness to water (for lace) (contact method))	-	500	-

02 Sep, 2027

-
Exclusion: Table-1 (vi), Table-1 (ix), Table-2 (v) & Table-1 (x)- Chemical Requirement, Table 1 xii Lead

4311

DELHI TEST HOUSE, Azadhpur

8131406

IS 737 (2024)

WROUGHT ALUMINIUM AND ALUMINIUM ALLOY SHEET AND STRIP FOR GENERAL ENGINEERING PURPOSES SPECIFICATION (Fifth Revision)

ALL

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 7(Chemical Composition - IS 504/ IS 504 (Part-1 to 12)/ IS 504 (Part-13 to 16)/ ASTM E 1251/ IS 11035)	-	7000	NA
Cl. 7(Si - IS 504 (Part-1)/ ASTM E 1251/ IS 11035)	-	500	NA
Cl. 7(Fe - IS 504 (Part-2)/ ASTM E 1251/ IS 11035)	-	500	NA
Cl. 7(Cu - IS 504 (Part-3)/ ASTM E 1251/ IS 11035)	-	500	NA
Cl. 7(Mn - IS 504 (Part-5)/ ASTM E 1251/ IS 11035)	-	500	NA
Cl. 7(Mg - IS 504 (Part-6)/ ASTM E 1251/ IS 11035)	-	500	NA
Cl. 7(Cr - IS 504 (Part-8)/ ASTM E 1251/ IS 11035)	-	500	NA
Cl. 7(Zn - IS 504 (Part-4)/ ASTM E 1251/ IS 11035)	-	500	NA
Cl. 7(Ti - IS 504 (Part-11)/ ASTM E 1251/ IS 11035)	-	500	NA
Cl. 7(Others (Each) - IS 504/ IS 504 (Part-1 to 12)/ IS 504 (Part-13 to 16)/ ASTM E 1251/ IS 11035)	-	5000	NA
Cl. 7(Others (Total) - IS 504/ IS 504 (Part-1 to 12)/ IS 504 (Part-13 to 16)/ ASTM E 1251/ IS 11035)	-	500	NA
Cl. 8(Mechanical Properties - IS 1608 (Part-1))	-	5000	NA
Cl. 8.1(0.2% Proof Stress - IS 1608 (Part-1))	-	2000	NA
Cl. 8.1(Tensile Strength - IS 1608 (Part-1))	-	2000	NA
Cl. 8.1(Elongation on 50mm Gauge Length - IS 1608 (Part-1))	-	1000	NA
Cl. 8.2(Bend Test - IS 1599)	-	1000	NA
Cl. 10(Dimensions and Tolerances - IS 737/ IS 2676)	-	1000	NA
Cl. 13.1(Marking - IS 737)	-	250	NA
Cl. 7(Al - IS 504)	-	500	NA
Cl. 4(Ordering Information - IS 737)	-	0	NA
Cl. 4 (a)(Grade/ Thickness - IS 737)	-	0	NA
Cl. 4 (b)(Condition - IS 737)	-	0	NA
Cl. 4 (c)(Quantity in Kg - IS 737)	-	0	NA
Cl. 4 (d)(Size - Thickness X Width X Length (T X W X L) in mm for sheets and (T X W) in mm for Strips/ Coils - IS 737)	-	0	NA
Cl. 4 (e)(Coil ID and Coil Weight for Strips/ Coils - IS 737)	-	0	NA
Cl. 4 (f)(Core/ Spool Requirement for Coils - IS 737)	-	0	NA
Cl. 4 (g)(Packing Mode - IS 737)	-	0	NA
Cl. 5(Supply for Material - IS 737/ IS 10259)	-	0	NA
Cl. 9(Condition - IS 737/ IS 5052)	-	0	NA
Cl. 11(Selection of Test Samples - IS 737)	-	0	NA
Cl. 11.1(Sheet and Strip of Aluminium or Non - Heat Treatable Aluminium Alloy - IS 737)	-	0	NA
Cl. 11.2(Sheet and Strip of Heat - Treatable Aluminium Alloys - IS 737)	-	0	NA
Cl. 12(Retests - IS 737/ IS 10259)	-	0	NA
Cl. 13(Packaging - IS 737/ IS 10259)	-	0	NA
Cl. 6(Freedom from Defects - IS 737)	-	250	NA

17 Jun, 2027

-
Included w.e.f.12.03.2025

4312

The Synthetic and Art Silk Mills' Research Association (SASMIRA), MUMBAI

7175004

IS 16513 (2016)

Agro textiles “ Insect nets for agriculture and horticulture purposes “ Specification

18500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6/6.1( REQUIREMENTS Dimensions and Mass a) Length)	-	400	-
6/6.1( REQUIREMENTS Dimensions and Mass b) width)	-	400	-
6/6.1( REQUIREMENTS Dimensions and Mass c) Mass gm/m2)	-	400	-
4.2( Netting Fabric)	-	200	-
4/4.1(b) percent on avarage value; and( MATERIAL / HDPE Monofilament Yarn)	-	400	-
4/4.1(a) percent on individual value; and( MATERIAL / HDPE Monofilament Yarn)	-	400	-
4.2( Netting Fabric)	-	200	-
4.2( Netting Fabric)	-	200	-
5.0(types a) Type I — having mesh of 30; b) Type II — having mesh of 40; andc) c) Type III — having mesh of 50)	-	2100	-
4/4.1.1/60°C / 95°C( MATERIAL / HDPE Monofilament Yarn)	-	1000	-
4.3( Colour)	-	0	-
6.2(Table-1)	-	12300	-
6.2/3(cover factor)	-	500	-

14 Dec, 2026

-
-

4313

Unique Test House

9134536

IS 9295 (2024)

STEEL TUBES FOR IDLERS FOR BELT CONVEYORS - SPECIFICATION (second revision)

ALL GRADE TYPE DESIGNATION AND SIZE

7200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
As per Clause 5(Types /Grade and Designation)	-	500	-
As per clause 6(Material)	-	100	-
As per clause 7(Manufacture)	-	200	-
As per clause 7.1.5(Sulphur)	-	800	-
As per clause 7.1.6(Phosphorus)	-	800	-
As per clause 8(Mechanical Properties)	-	200	-
As per clause 8.1(Tensile Test)	-	700	-
As per clause 8.1.1(Yield Stress)	-	700	-
As per clause 8.1.2(Elongation)	-	700	-
As per clause 8.2(Drift Expansion Test)	-	1000	-
As per clause 8.3(Flattening Test)	-	1500	-
Cl-9.1, Table-2(Outside Diameter)	-	700	-
As per clause 10(Hardness Test)	-	1000	-
As per clause 11(Mechanical Test)	-	1500	-
As per clause 12(Retests)	-	1500	-
As per clause 13(Dimension Tolerance)	-	500	-
As per clause 14(Workmanship)	-	200	-
As per clause 15(Straightness)	-	800	-
As per clause 16(Length)	-	200	-
As per clause 17(Surface Protection)	-	500	-
As per clause 18(Marking)	-	500	-

07 Sep, 2028

-
-

4314

SIIR, Delhi Shriram Institute For Industrial Research

8102006

IS 16415 (2015)

Composite cement - Specification

Composite Cement

26000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Chemical Requirements)	-	0	-
7(Physical Requirement)	-	0	-
6 -Table - 2 i(Insoluble residue - Cl 4.10 of IS 4032:1985)	-	1000	30% Discount
6 -Table - 2 ii(Magnesia - Cl 4.8 of IS 4032:1985)	-	2000	30% Discount
6 -Table - 2 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-	1000	30% Discount
6 -Table - 2 iv(Sulphide sulphur (S) - Cl 6.12 of IS 4032:1985)	-	1000	30% Discount
6 -Table - 2 v(Loss on ignition - Cl 4.2 of IS 4032:1985)	-	1000	30% Discount
6 -Table - 2 vi(Chloride content - Cl 4.13 of IS 4032:1985)	-	1000	30% Discount
Cl. 6.1,Table 2(Alkali content)	-	2000	30% Discount
6 -Table - 2 i(Insoluble residue - Cl 4.10 of IS 4032:1985)	-	0	-
6 -Table - 2 ii(Magnesia - Cl 4.8 of IS 4032:1985)	-	0	-
6 -Table - 2 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-	0	-
6 -Table - 2 iv(Sulphide sulphur (S) - Cl 6.12 of IS 4032:1985)	-	0	-
6 -Table - 2 v(Loss on ignition - Cl 4.2 of IS 4032:1985)	-	0	-
6 -Table - 2 vi(Chloride content - Cl 4.13 of IS 4032:1985)	-	0	-
Cl. 6.1,Table 2(Chloride content)	-	0	-
Cl. 6.1,Table 2(Loss on ignition)	-	0	-
Cl. 6.1,Table 2(Suilphide sulphur)	-	0	-
Cl. 6.1,Table 2(Total sulphur content calculated as sulphuric anhydride)	-	0	-
Cl. 6.1,Table 2(Magnesia)	-	0	-
Cl. 6.1,Table 2(Insoluble residue)	-	0	-
7 and Table 3 i(Fineness IS 4031(Part 2))	-	1000	30% Discount
7 and Table 3 ii a(Soundness, Le-Chate1ier expansion IS 4031(Part 3) )	-	1000	30% Discount
7 and Table 3 ii b(Soundness, Autoclave expansion IS 4031(Part 3) )	-	1000	30% Discount
7 and Table 3 iii a(Setting Time ( by Vicat Apparatus), Initial IS 4031(Part 5))	-	500	30% Discount
7 and Table 3 iii b(Setting Time ( by Vicat Apparatus ), Final IS 4031(Part 5))	-	500	30% Discount
7 and Table 3 iv a(Compretsive Strenqth .72 ± 1 hr IS 4031(Part 6))	-	5000	30% Discount
7 and Table 3 iv b(Compretsive Strenqth 168 ± 2 hr IS 4031(Part 6))	-	0	-
7 and Table 3 iv c(Compretsive Strenqth 672 ± 4 hr IS 4031(Part 6))	-	0	-
7 and Table 3 v(Drying shrinkage IS 4031(Part 10))	-	3000	30% Discount
7 and Table 3 vi(Transverse strength (optional) IS 4031(Part 8) )	-	5000	30% Discount
7 and Table 3 i(Fineness IS 4031(Part 2))	-	0	-
7 and Table 3 ii a(Soundness, Le-Chate1ier expansion IS 4031(Part 3) )	-	0	-
7 and Table 3 ii b(Soundness, Autoclave expansion IS 4031(Part 3) )	-	0	-
7 and Table 3 iii a(Setting Time ( by Vicat Apparatus), Initial IS 4031(Part 5))	-	0	-
7 and Table 3 iii b(Setting Time ( by Vicat Apparatus ), Final IS 4031(Part 5))	-	0	-
7 and Table 3 iv a(Compretsive Strenqth .72 ± 1 hr IS 4031(Part 6))	-	0	-
7 and Table 3 iv b(Compretsive Strenqth 168 ± 2 hr IS 4031(Part 6))	-	0	-
7 and Table 3 iv c(Compretsive Strenqth 672 ± 4 hr IS 4031(Part 6))	-	0	-
7 and Table 3 v(Drying shrinkage IS 4031(Part 10))	-	0	-
7 and Table 3 vi(Transverse strength (optional) IS 4031(Part 8) )	-	0	-
6(Chemical Requirements)	-	0	-
7(Physical Requirement)	-	0	-
Cl. 6.1,Table 2(Alkali content)	-	0	-
Cl. 6.1,Table 2(Chloride content)	-	0	-
Cl. 6.1,Table 2(Loss on ignition)	-	0	-
Cl. 6.1,Table 2(Suilphide sulphur)	-	0	-
Cl. 6.1,Table 2(Total sulphur content calculated as sulphuric anhydride)	-	0	-
Cl. 6.1,Table 2(Magnesia)	-	0	-
Cl. 6.1,Table 2(Insoluble residue)	-	0	-

31 Dec, 2026

-
Included w.e.f.12.03.2025

4315

INDIAN TESTING LABORATORY PRIVATE LIMITED, GREATER NOIDA

8171306

IS 1285 (2023)

WROUGHT ALUMINIUM AND ALUMINIUM ALLOYS EXTRUDED ROUND TUBE AND HOLLOW SECTIONS FOR GENERAL ENGINEERINGPURPOSES SPECIFICATION

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1("The extruded round tube and hollow sections shall be sound and visually free from harmful defects. ")	-	500	-
6.2(Slight discoloration due to heat treatment, minor polishing marks and spiral marks due to roll straightening shall not be a cause for rejection.)	-	500	-
8("Dimensions and tolerances of the material shall be as laid down in the Indian Standards indicated below: a) Extruded round tube IS 2673; and b) Extruded hollow sections IS 6477.")	-	1000	-
9(" Extruded round tubes and hollow sections shall be made from alloys specified in IS 733. 9.2 The chemical analysis of the material shall be carried out either in accordance with the methods specified in IS 504 (Part 1 to 12) and IS 504 (Part 13 to 16) or by any other established instrumental/chemical method. In case of any dispute the method specified in relevant parts of IS 504 shall be used as referee method. However, when the method is not given in IS 504, the referee method shall be as agreed to between the purchaser and the manufacturer. ")	-	500	-
10(Tensile test)	-	1000	-
Cl.9.1(Aluminium- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Copper- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Magnesium- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Silicon- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Iron- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Manganese- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Zinc- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Titanium and/ or other grain refining elements- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Chromium- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Remarks (Ti+V) - IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Remarks (Cr+Mn) - IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Remarks (Total Impurities)- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-

15 Aug, 2028

-
Included w.e.f 12.03.2025

4316

VARDAN ENVIROLAB, GURUGRAM

8169616

IS 3736 (1995)

Canvas boots, rubber sole - Specification (Second Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4.1.7.4 Ageing(The boots shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the soles and heels of the boots shall conform to the physical requirements prescribed in Table 5. i) Tensile Length)	-	500	-
Cl.4.1.7.4 Ageing(ii) Elongation at break)	-	500	-
Cl.4.1.7.2 IS 3400 (Part 2) : 1980(2)Hardness, IRHD)	-	500	-
4.1.6 Fabric Laces Cl.4.1.6.1( The boots shall be provided with braided of cotton or man made or blended fabric laces 115 ± 5 cm in length, matching the colour of the upper. )	-	1000	-
Cl.4.1.1 upper IS 1969(d) Picks/dm)	-	500	-
Cl.4.4.5 ( Table 1.)(d) Picks/dm)	-	500	-
4.1.2 Lining Material(195 ± 5 picks/dm shall be used.)	-	500	-
Cl.4.1.1 upper IS 1969(c) Ends/dm )	-	500	-
Cl.4.4.5 ( Table 1.)(c) Ends/dm )	-	500	-
4.1.2 Lining Material(having 390 ± 10 ends/dm and )	-	500	-
Cl.4.1.7.2 IS 3400 (Part 4) : 1987 IS 3400 (Part 2) : 1980(Change in initial hardness after accelerated ageing for 24 h at l00 ± 1°C)	-	500	-
Cl.4.8 Adhesion Test(From the upper foxing portion where it is adhered to the canvas cut a strip of 8.0 ± 0.5 mm width along with the length of the sole at the waist portion and of sufficient lengh to permit separation over a length of at least 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10 mm per minute in accordance with IS 3400 (Part 5):1986 or the Static Dead Load Method as given in Annex C. The individual adhesion value noted/recorded shall not be less than 8 N (0.8 kgf) for each of the test pieces ( see Note under 4.7 ).')	-	1000	-
Cl.4.4.9(From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine)	-	500	-
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Tensile strength in MPa, Min)	-	500	-
Cl.4.1.3 Binding Material IS 1954:1990(Cotton tape NEWAR used as binding material shall conform to the requirements as mentioned in Table 2, when tested in accordance with the methods referred to in col 4 of Table 2. 1)Width, mm. Min )	-	500	-
Cl.4.4.3(The top, side and front edges of the quarters and tongue shall be bound with cotton tape NEWAR of not less than 13 mm width using variety No. 29 thread.)	-	500	-
Cl.4.1.7.3 IS 3400 (Part 10) : 1977(Compression set, in percent. Max)	-	500	-
Cl.4.4.4( The back of the quarter shall be reinforced with a strip, not less than 25 mm wide,of either upper material or canvas. In case of composite upper material the edges of the strip shall be bound by cotton tape ( NEWAR ). When canvas cloth is used the edges shall be folded and shall be stitched with two rows of stitching.)	-	500	-
Cl.4.7 Consolidation Test(From the quarter, cut a strip of 25.0 ± 0. 5 mm width along the length of the boot and of sufficient length to permit separation over a length of 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10mm per minute in accordance with IS 3400 (Part 5): 1986 or Static Dead Load Method as given in Annex C. The individual adhesion value for consolidation test shall not be less than 30 N (3.0 kgf) for each of the test pieces)	-	1000	-
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Elongation at break, in percent, Min)	-	500	-
IS 1969:1985(Breaking load on 50 cm test length. N, Min)	-	500	-
4.1.6 Fabric Laces Cl.4.1.6.1(The laces shall have a minimum breaking load of 450 N, when tested between 18 cm grips, the rate of traverse of power actuated grip being 30 cm/min.)	-	500	-
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles b)Cut growth at the end of 150 000 cycles, Percent, Max)	-	500	-
Cl.4.4.5 ( Table 1.)(b) Weft )	-	500	-
Cl.4.4.5 ( Table 1.)( in case of half bellow. Thefull bellow tongue shall be made out of canvas cloth as prescribed in Sl No. (i) of Table 1. Breaking load in N, Min a) Warp )	-	500	-
Cl.4.1.1 upper IS 1969(b)Weft)	-	500	-
Cl.4.1.1 upper IS 1969(Breaking load in N.Min (5 × 20 cm grip): a) Wrap)	-	500	-
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles a)Initial crack, Min)	-	500	-
4.1.2 Lining Material( 200 N Minin weft way (when tested in accordance with IS 1969 : 1985) )	-	500	-
4.1.2 Lining Material(For covering of the insole, cotton drill conforming to Table 1, Sl No. (ii) shall be used. For detachable insole, bleached cotton twill of breaking load 390 N Min in warp way and)	-	500	-
Cl.4.1.1 upper(The upper shall consist of Rip Stop Fabric of cotton or manmade or its blend being the over layer and cotton drill as an inner layer and shall conform to the requirements given at Sl No. (i) of Table 1. Sr.no 1.Overlayer Construction )	-	500	-
4.1.1.1 Colour fastness(The dyed fabrics prescribed in 4.1.1 shall be fast to daylight and mechanical washing. Fastness to daylight shall be of rating 4 or better, when tested in accordance with IS 686 : 1985 or IS 2454 : 1985.)	-	500	-
Cl.4.1.1.2( Fastness to mechanical washing (mild) shall be of rating 4 or better, when tested in accordance with IS 764 : 1979)	-	500	-
Cl.4.1.3.3( Black tapes shall be free from sulphur dyes when tested in accordance with Annex B.)	-	500	-
Cl.4.1.4 Reinforcement Material(The back seam, joining two quarters at the back of the heel shall be reinforced with a not less than 25 mm wide tape made out of material conforming to Sl No. (i) of Table 1)	-	500	-
Cl.4.1.5 Thread for Upper Closing Cl.4.1.5.1 (IS 1670:1991)(Sewing thread cotton, man made or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirements. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirement of specification.')	-	500	-
Cl.4.1.5.2( The colour of the threads shall be asagreed to between the purchaser and the supplier. The dyed threads shall conform to the following requirements)	-	500	-
4.1.6 Fabric Laces Cl.4.1.6.1(The two ends of the lace shall be provided with suitable metal or plastic tips. Black laces shall be free from sulphur dyes when tested in accordance with Annex B.)	-	500	-
Cl.4.1.7 Rubber Components Cl.4.1.7.1( the soles and heels shall conform to Type 2 of IS 5676:1995.)	-	500	-
Cl.4.1.7.2 IS 3400 (Part 9) : 1978( The rubber components shall conform to Table 4 when tested.' ( Page 3, Table 4, Note 1) — 'However in case it is not possible then 4.2.5.3 of IS 13695:1993 shall be followed. 1)Relative density, Max)	-	500	-
Cl.4.1.7.5 Thickness of components(Individual components of the boots shall comply with the thickness and material requirements prescribed in Table 6.)	-	500	-
Cl.4.3 Leg Height(The leg height of the boots for size 8 shall be 160 ± 2 mm with an increase or decrease of 4 mm of the nominal height for each bigger or smaller sizes respectively when measured at the inside from the back of the boot from insole to the top.)	-	500	-
Cl.4.4.2( The canvas upper shall be lined with bleached drill cloth.)	-	500	-
Cl.4.4.3( The upper shall be stitched on a lockstitch machine, with 30 to 40 stitches per decimetre by thread of variety No. 8 and variety No. 29 cotton sewing thread conforming to 4.1.5 using variety No. 29 for taping and binding and variety No. 8 for remaining seams. )	-	500	-
Cl.4.4.5 ( The tongue shall be either half or full bellow depending on the requirement of the purchaser andshall be made from composite material prescribed for the upper in 4.1.1.)	-	500	-
Cl.4.4.6( A minimum of seven aluminium, brass or steel eyelets having 10 mm diameter and wall thickness 0.30 to 0.35 mm shall be fitted in each face.')	-	500	-
Cl.4.4.7( The toe shall be reinforced with a toe puff cemented inside and outside with rubber toe cap. The heel piece (counter) or stiffener shall be set from the bottom of the lining and bound flat on the top edge with white cloth for binding of countertop edge with white clothfor binding of counter)	-	500	-
Cl.4.4.8( A strengthening rubber arch piece shall be firmly pasted and stitched at the middle arch of the inside quarter. Another strengthening rubber piece, circular in shape 35 ± 1 mm in diameter, may bepasted and stitched at the centre of the inside)	-	500	-
Cl.4.4.10( A 25 mm Min wide and 2 mm Min thick rubber golosh in serrated, diamond or any otherdesign, as agreed to between the purchaser and thesupplier, shall be fitted all round the sole edge of the boot. The golosh shall not extend below the edge of the sole.)	-	500	-
Cl.4.5.1(Cl.4.1.6.)( Each pair of boot shall be provided with a pair of braided fabric laces of the quality as prescribed in 4.1.6.)	-	500	-
Cl.4.5.2( In appearance, general workmanship, finish and in all other respects, not defined in this standard, the boot shall be similar to those of the sample approved by the purchaser, if any.)	-	500	-
Cl.4.6 Mass(The mass of finished boots, rubber sole, of size 8 shall not exceed 1130 g per pair, and the mass shall increase or decrease by 75 g per pair for each bigger or smaller size respectively.)	-	500	-
Cl.4.9 Composite Breaking Strength Test( From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine.Rate of traverse of pulling jaw shall be 100 ± 5 mm per minute. Two such test pieces will be required to be obtained from the made up footwear and will be subjected to test to break each test piece. Mean value of each set of test pieces comprising of length wise and height wise test pieces will be 1 000 N/25 mm width minimum.')	-	500	-
Cl.4.1.7.4 Ageing(The boots shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the soles and heels of the boots shall conform to the physical requirements prescribed in Table 5. i) Tensile Length)	-	0	PARAMETER REPEAT
Cl.4.1.7.4 Ageing(ii) Elongation at break)	-	0	PARAMETER REPEAT
Cl.4.1.7.2 IS 3400 (Part 2) : 1980(2)Hardness, IRHD)	-	0	PARAMETER REPEAT
4.1.6 Fabric Laces Cl.4.1.6.1( The boots shall be provided with braided of cotton or man made or blended fabric laces 115 ± 5 cm in length, matching the colour of the upper. )	-	0	PARAMETER REPEAT
Cl.4.1.1 upper IS 1969(d) Picks/dm)	-	0	PARAMETER REPEAT
Cl.4.4.5 ( Table 1.)(d) Picks/dm)	-	0	PARAMETER REPEAT
4.1.2 Lining Material(195 ± 5 picks/dm shall be used.)	-	0	PARAMETER REPEAT
Cl.4.1.1 upper IS 1969(c) Ends/dm )	-	0	PARAMETER REPEAT
Cl.4.4.5 ( Table 1.)(c) Ends/dm )	-	0	PARAMETER REPEAT
4.1.2 Lining Material(having 390 ± 10 ends/dm and )	-	0	PARAMETER REPEAT
Cl.4.1.7.2 IS 3400 (Part 4) : 1987 IS 3400 (Part 2) : 1980(Change in initial hardness after accelerated ageing for 24 h at l00 ± 1°C)	-	0	PARAMETER REPEAT
Cl.4.8 Adhesion Test(From the upper foxing portion where it is adhered to the canvas cut a strip of 8.0 ± 0.5 mm width along with the length of the sole at the waist portion and of sufficient lengh to permit separation over a length of at least 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10 mm per minute in accordance with IS 3400 (Part 5):1986 or the Static Dead Load Method as given in Annex C. The individual adhesion value noted/recorded shall not be less than 8 N (0.8 kgf) for each of the test pieces ( see Note under 4.7 ).')	-	0	PARAMETER REPEAT
Cl.4.4.9(From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine)	-	0	PARAMETER REPEAT
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Tensile strength in MPa, Min)	-	0	PARAMETER REPEAT
Cl.4.1.3 Binding Material IS 1954:1990(Cotton tape NEWAR used as binding material shall conform to the requirements as mentioned in Table 2, when tested in accordance with the methods referred to in col 4 of Table 2. 1)Width, mm. Min )	-	0	PARAMETER REPEAT
Cl.4.4.3(The top, side and front edges of the quarters and tongue shall be bound with cotton tape NEWAR of not less than 13 mm width using variety No. 29 thread.)	-	0	PARAMETER REPEAT
Cl.4.1.7.3 IS 3400 (Part 10) : 1977(Compression set, in percent. Max)	-	0	PARAMETER REPEAT
Cl.4.4.4( The back of the quarter shall be reinforced with a strip, not less than 25 mm wide,of either upper material or canvas. In case of composite upper material the edges of the strip shall be bound by cotton tape ( NEWAR ). When canvas cloth is used the edges shall be folded and shall be stitched with two rows of stitching.)	-	0	PARAMETER REPEAT
Cl.4.7 Consolidation Test(From the quarter, cut a strip of 25.0 ± 0. 5 mm width along the length of the boot and of sufficient length to permit separation over a length of 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10mm per minute in accordance with IS 3400 (Part 5): 1986 or Static Dead Load Method as given in Annex C. The individual adhesion value for consolidation test shall not be less than 30 N (3.0 kgf) for each of the test pieces)	-	0	PARAMETER REPEAT
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Elongation at break, in percent, Min)	-	0	PARAMETER REPEAT
IS 1969:1985(Breaking load on 50 cm test length. N, Min)	-	0	PARAMETER REPEAT
4.1.6 Fabric Laces Cl.4.1.6.1(The laces shall have a minimum breaking load of 450 N, when tested between 18 cm grips, the rate of traverse of power actuated grip being 30 cm/min.)	-	0	PARAMETER REPEAT
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles b)Cut growth at the end of 150 000 cycles, Percent, Max)	-	0	PARAMETER REPEAT
Cl.4.4.5 ( Table 1.)(b) Weft )	-	0	PARAMETER REPEAT
Cl.4.4.5 ( Table 1.)( in case of half bellow. Thefull bellow tongue shall be made out of canvas cloth as prescribed in Sl No. (i) of Table 1. Breaking load in N, Min a) Warp )	-	0	PARAMETER REPEAT
Cl.4.1.1 upper IS 1969(b)Weft)	-	0	PARAMETER REPEAT
Cl.4.1.1 upper IS 1969(Breaking load in N.Min (5 × 20 cm grip): a) Wrap)	-	0	PARAMETER REPEAT
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles a)Initial crack, Min)	-	0	PARAMETER REPEAT
4.1.2 Lining Material( 200 N Minin weft way (when tested in accordance with IS 1969 : 1985) )	-	0	PARAMETER REPEAT
4.1.2 Lining Material(For covering of the insole, cotton drill conforming to Table 1, Sl No. (ii) shall be used. For detachable insole, bleached cotton twill of breaking load 390 N Min in warp way and)	-	0	PARAMETER REPEAT
Cl.4.1.1 upper(The upper shall consist of Rip Stop Fabric of cotton or manmade or its blend being the over layer and cotton drill as an inner layer and shall conform to the requirements given at Sl No. (i) of Table 1. Sr.no 1.Overlayer Construction )	-	0	PARAMETER REPEAT
4.1.1.1 Colour fastness(The dyed fabrics prescribed in 4.1.1 shall be fast to daylight and mechanical washing. Fastness to daylight shall be of rating 4 or better, when tested in accordance with IS 686 : 1985 or IS 2454 : 1985.)	-	0	PARAMETER REPEAT
Cl.4.1.1.2( Fastness to mechanical washing (mild) shall be of rating 4 or better, when tested in accordance with IS 764 : 1979)	-	0	PARAMETER REPEAT
Cl.4.1.3.3( Black tapes shall be free from sulphur dyes when tested in accordance with Annex B.)	-	0	PARAMETER REPEAT
Cl.4.1.4 Reinforcement Material(The back seam, joining two quarters at the back of the heel shall be reinforced with a not less than 25 mm wide tape made out of material conforming to Sl No. (i) of Table 1)	-	0	PARAMETER REPEAT
Cl.4.1.5 Thread for Upper Closing Cl.4.1.5.1 (IS 1670:1991)(Sewing thread cotton, man made or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirements. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirement of specification.')	-	0	PARAMETER REPEAT
Cl.4.1.5.2( The colour of the threads shall be asagreed to between the purchaser and the supplier. The dyed threads shall conform to the following requirements)	-	0	PARAMETER REPEAT
4.1.6 Fabric Laces Cl.4.1.6.1(The two ends of the lace shall be provided with suitable metal or plastic tips. Black laces shall be free from sulphur dyes when tested in accordance with Annex B.)	-	0	PARAMETER REPEAT
Cl.4.1.7 Rubber Components Cl.4.1.7.1( the soles and heels shall conform to Type 2 of IS 5676:1995.)	-	0	PARAMETER REPEAT
Cl.4.1.7.2 IS 3400 (Part 9) : 1978( The rubber components shall conform to Table 4 when tested.' ( Page 3, Table 4, Note 1) — 'However in case it is not possible then 4.2.5.3 of IS 13695:1993 shall be followed. 1)Relative density, Max)	-	0	PARAMETER REPEAT
Cl.4.1.7.5 Thickness of components(Individual components of the boots shall comply with the thickness and material requirements prescribed in Table 6.)	-	0	PARAMETER REPEAT
Cl.4.3 Leg Height(The leg height of the boots for size 8 shall be 160 ± 2 mm with an increase or decrease of 4 mm of the nominal height for each bigger or smaller sizes respectively when measured at the inside from the back of the boot from insole to the top.)	-	0	PARAMETER REPEAT
Cl.4.4.2( The canvas upper shall be lined with bleached drill cloth.)	-	0	PARAMETER REPEAT
Cl.4.4.3( The upper shall be stitched on a lockstitch machine, with 30 to 40 stitches per decimetre by thread of variety No. 8 and variety No. 29 cotton sewing thread conforming to 4.1.5 using variety No. 29 for taping and binding and variety No. 8 for remaining seams. )	-	0	PARAMETER REPEAT
Cl.4.4.5 ( The tongue shall be either half or full bellow depending on the requirement of the purchaser andshall be made from composite material prescribed for the upper in 4.1.1.)	-	0	PARAMETER REPEAT
Cl.4.4.6( A minimum of seven aluminium, brass or steel eyelets having 10 mm diameter and wall thickness 0.30 to 0.35 mm shall be fitted in each face.')	-	0	PARAMETER REPEAT
Cl.4.4.7( The toe shall be reinforced with a toe puff cemented inside and outside with rubber toe cap. The heel piece (counter) or stiffener shall be set from the bottom of the lining and bound flat on the top edge with white cloth for binding of countertop edge with white clothfor binding of counter)	-	0	PARAMETER REPEAT
Cl.4.4.8( A strengthening rubber arch piece shall be firmly pasted and stitched at the middle arch of the inside quarter. Another strengthening rubber piece, circular in shape 35 ± 1 mm in diameter, may bepasted and stitched at the centre of the inside)	-	0	PARAMETER REPEAT
Cl.4.4.10( A 25 mm Min wide and 2 mm Min thick rubber golosh in serrated, diamond or any otherdesign, as agreed to between the purchaser and thesupplier, shall be fitted all round the sole edge of the boot. The golosh shall not extend below the edge of the sole.)	-	0	PARAMETER REPEAT
Cl.4.5.1(Cl.4.1.6.)( Each pair of boot shall be provided with a pair of braided fabric laces of the quality as prescribed in 4.1.6.)	-	0	PARAMETER REPEAT
Cl.4.5.2( In appearance, general workmanship, finish and in all other respects, not defined in this standard, the boot shall be similar to those of the sample approved by the purchaser, if any.)	-	0	PARAMETER REPEAT
Cl.4.6 Mass(The mass of finished boots, rubber sole, of size 8 shall not exceed 1130 g per pair, and the mass shall increase or decrease by 75 g per pair for each bigger or smaller size respectively.)	-	0	PARAMETER REPEAT
Cl.4.9 Composite Breaking Strength Test( From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine.Rate of traverse of pulling jaw shall be 100 ± 5 mm per minute. Two such test pieces will be required to be obtained from the made up footwear and will be subjected to test to break each test piece. Mean value of each set of test pieces comprising of length wise and height wise test pieces will be 1 000 N/25 mm width minimum.')	-	0	PARAMETER REPEAT
Cl.4.1.7.4 Ageing(The boots shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the soles and heels of the boots shall conform to the physical requirements prescribed in Table 5. i) Tensile Length)	-	0	PARAMETER REPEAT
Cl.4.1.7.4 Ageing(ii) Elongation at break)	-	0	PARAMETER REPEAT
Cl.4.1.7.2 IS 3400 (Part 2) : 1980(2)Hardness, IRHD)	-	0	PARAMETER REPEAT
4.1.6 Fabric Laces Cl.4.1.6.1( The boots shall be provided with braided of cotton or man made or blended fabric laces 115 ± 5 cm in length, matching the colour of the upper. )	-	0	PARAMETER REPEAT
Cl.4.1.1 upper IS 1969(d) Picks/dm)	-	0	PARAMETER REPEAT
Cl.4.4.5 ( Table 1.)(d) Picks/dm)	-	0	PARAMETER REPEAT
4.1.2 Lining Material(195 ± 5 picks/dm shall be used.)	-	0	PARAMETER REPEAT
Cl.4.1.1 upper IS 1969(c) Ends/dm )	-	0	PARAMETER REPEAT
Cl.4.4.5 ( Table 1.)(c) Ends/dm )	-	0	PARAMETER REPEAT
4.1.2 Lining Material(having 390 ± 10 ends/dm and )	-	0	PARAMETER REPEAT
Cl.4.1.7.2 IS 3400 (Part 4) : 1987 IS 3400 (Part 2) : 1980(Change in initial hardness after accelerated ageing for 24 h at l00 ± 1°C)	-	0	PARAMETER REPEAT
Cl.4.8 Adhesion Test(From the upper foxing portion where it is adhered to the canvas cut a strip of 8.0 ± 0.5 mm width along with the length of the sole at the waist portion and of sufficient lengh to permit separation over a length of at least 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10 mm per minute in accordance with IS 3400 (Part 5):1986 or the Static Dead Load Method as given in Annex C. The individual adhesion value noted/recorded shall not be less than 8 N (0.8 kgf) for each of the test pieces ( see Note under 4.7 ).')	-	0	PARAMETER REPEAT
Cl.4.4.9(From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine)	-	0	PARAMETER REPEAT
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Tensile strength in MPa, Min)	-	0	PARAMETER REPEAT
Cl.4.1.3 Binding Material IS 1954:1990(Cotton tape NEWAR used as binding material shall conform to the requirements as mentioned in Table 2, when tested in accordance with the methods referred to in col 4 of Table 2. 1)Width, mm. Min )	-	0	PARAMETER REPEAT
Cl.4.4.3(The top, side and front edges of the quarters and tongue shall be bound with cotton tape NEWAR of not less than 13 mm width using variety No. 29 thread.)	-	0	PARAMETER REPEAT
Cl.4.1.7.3 IS 3400 (Part 10) : 1977(Compression set, in percent. Max)	-	0	PARAMETER REPEAT
Cl.4.4.4( The back of the quarter shall be reinforced with a strip, not less than 25 mm wide,of either upper material or canvas. In case of composite upper material the edges of the strip shall be bound by cotton tape ( NEWAR ). When canvas cloth is used the edges shall be folded and shall be stitched with two rows of stitching.)	-	0	PARAMETER REPEAT
Cl.4.7 Consolidation Test(From the quarter, cut a strip of 25.0 ± 0. 5 mm width along the length of the boot and of sufficient length to permit separation over a length of 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10mm per minute in accordance with IS 3400 (Part 5): 1986 or Static Dead Load Method as given in Annex C. The individual adhesion value for consolidation test shall not be less than 30 N (3.0 kgf) for each of the test pieces)	-	0	PARAMETER REPEAT
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Elongation at break, in percent, Min)	-	0	PARAMETER REPEAT
IS 1969:1985(Breaking load on 50 cm test length. N, Min)	-	0	PARAMETER REPEAT
4.1.6 Fabric Laces Cl.4.1.6.1(The laces shall have a minimum breaking load of 450 N, when tested between 18 cm grips, the rate of traverse of power actuated grip being 30 cm/min.)	-	0	PARAMETER REPEAT
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles b)Cut growth at the end of 150 000 cycles, Percent, Max)	-	0	PARAMETER REPEAT
Cl.4.4.5 ( Table 1.)(b) Weft )	-	0	PARAMETER REPEAT
Cl.4.4.5 ( Table 1.)( in case of half bellow. Thefull bellow tongue shall be made out of canvas cloth as prescribed in Sl No. (i) of Table 1. Breaking load in N, Min a) Warp )	-	0	PARAMETER REPEAT
Cl.4.1.1 upper IS 1969(b)Weft)	-	0	PARAMETER REPEAT
Cl.4.1.1 upper IS 1969(Breaking load in N.Min (5 × 20 cm grip): a) Wrap)	-	0	PARAMETER REPEAT
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles a)Initial crack, Min)	-	0	PARAMETER REPEAT
4.1.2 Lining Material( 200 N Minin weft way (when tested in accordance with IS 1969 : 1985) )	-	0	PARAMETER REPEAT
4.1.2 Lining Material(For covering of the insole, cotton drill conforming to Table 1, Sl No. (ii) shall be used. For detachable insole, bleached cotton twill of breaking load 390 N Min in warp way and)	-	0	PARAMETER REPEAT
Cl.4.1.1 upper(The upper shall consist of Rip Stop Fabric of cotton or manmade or its blend being the over layer and cotton drill as an inner layer and shall conform to the requirements given at Sl No. (i) of Table 1. Sr.no 1.Overlayer Construction )	-	0	PARAMETER REPEAT
4.1.1.1 Colour fastness(The dyed fabrics prescribed in 4.1.1 shall be fast to daylight and mechanical washing. Fastness to daylight shall be of rating 4 or better, when tested in accordance with IS 686 : 1985 or IS 2454 : 1985.)	-	0	PARAMETER REPEAT
Cl.4.1.1.2( Fastness to mechanical washing (mild) shall be of rating 4 or better, when tested in accordance with IS 764 : 1979)	-	0	PARAMETER REPEAT
Cl.4.1.3.3( Black tapes shall be free from sulphur dyes when tested in accordance with Annex B.)	-	0	PARAMETER REPEAT
Cl.4.1.4 Reinforcement Material(The back seam, joining two quarters at the back of the heel shall be reinforced with a not less than 25 mm wide tape made out of material conforming to Sl No. (i) of Table 1)	-	0	PARAMETER REPEAT
Cl.4.1.5 Thread for Upper Closing Cl.4.1.5.1 (IS 1670:1991)(Sewing thread cotton, man made or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirements. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirement of specification.')	-	0	PARAMETER REPEAT
Cl.4.1.5.2( The colour of the threads shall be asagreed to between the purchaser and the supplier. The dyed threads shall conform to the following requirements)	-	0	PARAMETER REPEAT
4.1.6 Fabric Laces Cl.4.1.6.1(The two ends of the lace shall be provided with suitable metal or plastic tips. Black laces shall be free from sulphur dyes when tested in accordance with Annex B.)	-	0	PARAMETER REPEAT
Cl.4.1.7 Rubber Components Cl.4.1.7.1( the soles and heels shall conform to Type 2 of IS 5676:1995.)	-	0	PARAMETER REPEAT
Cl.4.1.7.2 IS 3400 (Part 9) : 1978( The rubber components shall conform to Table 4 when tested.' ( Page 3, Table 4, Note 1) — 'However in case it is not possible then 4.2.5.3 of IS 13695:1993 shall be followed. 1)Relative density, Max)	-	0	PARAMETER REPEAT
Cl.4.1.7.5 Thickness of components(Individual components of the boots shall comply with the thickness and material requirements prescribed in Table 6.)	-	0	PARAMETER REPEAT
Cl.4.3 Leg Height(The leg height of the boots for size 8 shall be 160 ± 2 mm with an increase or decrease of 4 mm of the nominal height for each bigger or smaller sizes respectively when measured at the inside from the back of the boot from insole to the top.)	-	0	PARAMETER REPEAT
Cl.4.4.2( The canvas upper shall be lined with bleached drill cloth.)	-	0	PARAMETER REPEAT
Cl.4.4.3( The upper shall be stitched on a lockstitch machine, with 30 to 40 stitches per decimetre by thread of variety No. 8 and variety No. 29 cotton sewing thread conforming to 4.1.5 using variety No. 29 for taping and binding and variety No. 8 for remaining seams. )	-	0	PARAMETER REPEAT
Cl.4.4.5 ( The tongue shall be either half or full bellow depending on the requirement of the purchaser andshall be made from composite material prescribed for the upper in 4.1.1.)	-	0	PARAMETER REPEAT
Cl.4.4.6( A minimum of seven aluminium, brass or steel eyelets having 10 mm diameter and wall thickness 0.30 to 0.35 mm shall be fitted in each face.')	-	0	PARAMETER REPEAT
Cl.4.4.7( The toe shall be reinforced with a toe puff cemented inside and outside with rubber toe cap. The heel piece (counter) or stiffener shall be set from the bottom of the lining and bound flat on the top edge with white cloth for binding of countertop edge with white clothfor binding of counter)	-	0	PARAMETER REPEAT
Cl.4.4.8( A strengthening rubber arch piece shall be firmly pasted and stitched at the middle arch of the inside quarter. Another strengthening rubber piece, circular in shape 35 ± 1 mm in diameter, may bepasted and stitched at the centre of the inside)	-	0	PARAMETER REPEAT
Cl.4.4.10( A 25 mm Min wide and 2 mm Min thick rubber golosh in serrated, diamond or any otherdesign, as agreed to between the purchaser and thesupplier, shall be fitted all round the sole edge of the boot. The golosh shall not extend below the edge of the sole.)	-	0	PARAMETER REPEAT
Cl.4.5.1(Cl.4.1.6.)( Each pair of boot shall be provided with a pair of braided fabric laces of the quality as prescribed in 4.1.6.)	-	0	PARAMETER REPEAT
Cl.4.5.2( In appearance, general workmanship, finish and in all other respects, not defined in this standard, the boot shall be similar to those of the sample approved by the purchaser, if any.)	-	0	PARAMETER REPEAT
Cl.4.6 Mass(The mass of finished boots, rubber sole, of size 8 shall not exceed 1130 g per pair, and the mass shall increase or decrease by 75 g per pair for each bigger or smaller size respectively.)	-	0	PARAMETER REPEAT
Cl.4.9 Composite Breaking Strength Test( From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine.Rate of traverse of pulling jaw shall be 100 ± 5 mm per minute. Two such test pieces will be required to be obtained from the made up footwear and will be subjected to test to break each test piece. Mean value of each set of test pieces comprising of length wise and height wise test pieces will be 1 000 N/25 mm width minimum.')	-	0	PARAMETER REPEAT
4.1.3.2(Fastness to mechanical washing (mild))	-	500	-
4.1.3(Cotton tape NEWAR)	-	200	-
Table 2 (ii)(Breaking load on 50 cm test length. N, Min)	-	500	-
4.1.6.2(Laces- Fastness to daylight)	-	500	-
4.1.6.3(Laces- Fastness to mechanical washing (mild))	-	500	-

26 Dec, 2027

-
Included w.e.f.17.06.2025

4317

Hi Physix Laboratory India Private Limited, Pune

7126926

IS 302 : Part 2 : Sec 8 (2024)

Household and Similar Electrical Appliances âSafety Part 2 Particular Requirements Section 8 Shavers, Hair Clippers and Similar Appliances (First Revision)

73000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking and instructions)	-	2000	-
8(Protection against access to live parts)	-	2000	-
10(Power input and current)	-	2000	-
11(Heating)	-	4000	-
12(Charging of metal-ion batteries)	-	15000	-
13.1 &13.2(Leakage current test)	-	1500	-
13.1 &13.3(Electric strength test)	-	1500	-
14(Transient overvoltages)	-	2000	-
15(Moisture resistance)	-	2000	-
15.3(Moisture resistance)	-	2000	-
16.1 &16.2(Leakage current test)	-	1500	-
16.1 & 16.3(Electric strength test)	-	1500	-
17(Overload protection of transformers and associated circuits)	-	4000	-
19.1 to 19.13, Table No. - 9(Abnormal operation)	-	5000	Charges applicable excluding the test of Cl.19.11.4.1 to Cl.19.11.4.7. The testing charges for EMI/EMC Testing (Cl.19.11.4.1 to Cl.19.11.4.7) will be charged extra.
19.101(Abnormal operation)	-	0	Testing charges included in Cl.19.1 TO cL.19.13
20.1(Stability and mechanical hazards)	-	1000	-
20.2(Stability and mechanical hazards)	-	1000	-
21(Mechanical strength)	-	3000	-
21.101(Mechanical strength)	-	0	Testing charges included in Cl.21
21.102(Mechanical strength)	-	0	Testing charges included in Cl.21
21.103(Mechanical strength)	-	0	Testing charges included in Cl.21
22(Construction)	-	5000	-
22.101(Construction)	-	0	Testing charges included in Cl.22
22.102(Construction)	-	0	Testing charges included in Cl.22
22.103(Construction)	-	0	Testing charges included in Cl.22
23(Internal wiring)	-	2000	-
24(Components)	-	3000	-
25("Supply connection and external flexible cords")	-	1000	-
26("Terminals for external conductors")	-	1000	-
27(Provision for earthing)	-	2000	-
28(Screws and connections)	-	1000	-
29("Clearances, creepage distances and solid insulation")	-	2000	-
30(Resistance to heat and fire)	-	3000	-
31(Resistance to rusting)	-	1000	-
32("Radiation, toxicity and similar hazards")	-	1000	-

20 Jun, 2028

-
Included w.e.f 25.03.2025 Exclusion : Cl 24 (Components), Cl 32 ("Radiation, toxicity and similar hazards")

4318

DELHI TEST HOUSE, Azadhpur

8131406

IS 736 (1986)

Specification for wrought aluminium and aluminium alloy plate for general engineering purposes (Third Revision)

ALL

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Freedom from defect)	-	500	-
5(chemical composition)	-	4500	-
6.1 table 2(0.2% proof strength)	-	1700	-
6.1 table 2(tensile strength)	-	1700	-
6.1 table 2(Elongation)	-	1700	-
8(Dimensions & Tolerances)	-	2000	-
5.1, Table 1(Aluminium)	-	500	-
5.1, Table 1(Copper)	-	500	-
5.1, Table 1(Magnesium)	-	500	-
5.1, Table 1(Silicon)	-	500	-
5.1, Table 1(Iron)	-	500	-
5.1, Table 1(Mangnese)	-	500	-
5.1, Table 1(Zinc)	-	500	-
5.1, Table 1(Titanium and /or other grain refining element)	-	500	-
5.1, Table 1(Chromium)	-	500	-
5.1, Table 1(Vanadium)	-	500	-

17 Jun, 2027

-
Included w.e.f. 03.03.2025

4319

IDMA LABORATORIES LIMITED, PANCHKULA

9123236

IS 5405 (2025)

Disposable Sanitary Napkin/Panty Liner/Maternity Pad/Period Panty - Specification ( Third Revision )

Sanitary Napkin, Panty liner, Maternity Pad, Period panty

261600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Cover/Top sheet)	-	800	Testing charges are Rs. 800/- for Cl. no. 3.1 Cover / Top sheet, 3.2 Absorbent core & 3.3 Barrier or Bottom sheet.
3.2(Absorbent core)	-	0	Testing charges already mentioned above at cl. no. 3.1 Cover / Top sheet i.e. Rs. 800/-.
3.3(Barrier or bottom sheet)	-	0	Testing charges already mentioned above at cl. no. 3.1 Cover / Top sheet i.e. Rs. 800/-.
4.1(Types)	-	800	Testing charges are 800/- for cl. 4.1 & 4.2
4.2(shapes)	-	0	Testing charges are 800/- for cl. 4.1 & 4.2 already mentioned above.
5(Sizes)	-	800	Testing charges are 800/- for Size, Size class, Length (Absorbent core only, Width (Absorbent core only as per cl. 5 Table - 1.
Cl. 5 Table-1(Type)	-	0	Total testing charges are Rs. 2,61,600/- including Bio compatibility evaluation - Cytotoxicity, Irritation & Skin sensitization (as per cl. no. 7.4) & (excluding Compostability as per cl. 7.6).
Cl. 5 Table-1(Size class)	-	0	Testing charges are 800/- for Size, Size class, Length (Absorbent core only, Width (Absorbent core only as per cl. 5 Table - 1 already mentioned above.
Cl. 5 Table-1(Length (Absorbent core only))	-	0	Testing charges are 800/- for Size, Size class, Length (Absorbent core only, Width (Absorbent core only as per cl. 5 Table - 1 already mentioned above.
Cl. 5 Table-1(Width (Absorbent core only))	-	0	Testing charges are 800/- for Size, Size class, Length (Absorbent core only, Width (Absorbent core only as per cl. 5 Table - 1 already mentioned above.
6.1(Manufacture, workmanship and finish)	-	500	Testing charges are 500/- for cl. 6.1 & 6.2.
6.2(Manufacture, workmanship and finish)	-	0	Testing charges are 500/- for cl. 6.1 & 6.2 already mentioned above.
7.1(pH Test)	-	1000	Testing charges are Rs. 21,600/- excluding Bio compatibility evaluation - Cytotoxicity, Irritation & Skin sensitization (as per cl. no. 7.4) &excluding Compostability as per cl. 7.6).
7.2("Ability to Withstand Pressure after Absorption: Liquid Absorption ml, Min")	-	1200	Testing charges are 1200/- for cl. Ability to Withstand Pressure after Absorption & Ability to Withstand Pressure after Absorption - leakage.
7.3.1(Bacterial and Fungal Bioburden)	-	3000	-
7.3.2(Staphylococcus aureus)	-	3000	-
7.4(Biocompatibility evaluation - Cytotoxicity (IS/ISO 10993 P-5))	-	50000	-
7.4(Biocompatibility evaluation - Irritation (IS 17932 P-7))	-	70000	-
7.4(Biocompatibility evaluation - skin Sensitization (Optional) (IS 17932 P-6))	-	120000	-
Cl 7.5(Phthalate test- Combination)	-	8000	-
7.7(Anti bacterial activity value (Optional) (IS/ISO 20743))	-	2500	-
7.6(Compostability (Optional) (IS/ISO 17088))	-	0	Clause no. 7.6 Compostability (Optional) test is applied for Exclusion as the test facilities are currently not available.

31 Dec, 2026

-
Included w.e.f.05.03.2025 Exclusion Cl 7.6 (Compostability (Optional) (IS/ISO 17088)

4320

IDMA LABORATORIES LIMITED, PANCHKULA

9123236

IS 15219 (2024)

Aluminium phosphide powder formulation - Specification (first revision)

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2.1(Description - IS 15219:2002)	-	1000		-
3.3.1(Aluminium Phosphide Content - IS 6438:1980)	-	6000		-

31 Dec, 2026

-
Included w.e.f.24.04.2025

Bureau of Indian Standards

The National Standards Body of India

Search by IS Number