BIS - LIMS (Laboratory Information Management System)

Search by IS Number

Reset

11237 Results

S.No.

Lab Name

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

481

Kailtech Test and Research Centre Pvt. Ltd.

IS 13757 (1993)

Burnt Clay Fly Ash Building Bricks-specification

All

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.0(GENERAL QUALITY)	-	1000	General Requirement
6.1(Dimensions)	-	2000	All Dimensions and Tolerance
6.2(Tolerances)	-	2000	All Dimensions and Tolerance
7.1(Compressive Strength)	-	4000	Compressive Strength
7.3(Efforescence)	-	1500	Efflorescence

Complete

18 Dec, 2027

-
-

482

Kailtech Test and Research Centre Pvt. Ltd.

IS 6527 (1995)

Stainless steel wire rods - Specification (First Revision)

All

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 9(Tensile & Hardness)	-	8500	Tensile and Hardness
Cl 10(Diameter & Out Of Round)	-	500	Dimension
Cl. 10.1(Out of Round)	-	500	Dimension
Cl. 6(Freedom from defects)	-	500	Freedom from Defects
Cl. 9 .1 Table 3(0.2 % Proof Stress )	-	7500	0.2 % Proof Stress
Cl. 9 .1 Table 3(Elongation)	-	7500	Elongation
Cl. 9.2 Table 4(Hardness)	-	1000	Hardness

Complete

18 Dec, 2027

-
-

483

Kailtech Test and Research Centre Pvt. Ltd.

IS 6528 (1995)

Stainless steel wire - Specification (First Revision)

All

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Table 7(Workmanship)	-	14250	Chemical Composition
Cl 6(Workmanship)	-	1000	Freedom from Defects
Cl 9.1 & Table 3(Diameter & Out Of Round)	-	1000	Dimensions
Cl 10(UTM)	-	7500	Tensile Test

Complete

18 Dec, 2027

-
-

484

Kailtech Test and Research Centre Pvt. Ltd.

IS 3975 (1999)

Low carbon galvanized steel wires, formed wires and tapes for armouring of cables - Specification (Third Revision)

All

4050 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Dimensions)	-	1000	NA
11(Freedom from defects)	-	1000	Freedom from Defects
9.1(Galvanizing Requirements )	-	1000	Mass of Coating
9.2(Galvanizing Requirements )	-	1000	Uniformity of Coating
9.3(Galvanizing Requirements )	-	2000	Adhesion Test
8.1(Mechanical Properties (as per table 5 of IS 1608))	-	3000	Tensile
8.2(Mechanical Properties (as per IS 1717))	-	2000	Torsion
8.3(Mechanical Properties (as per IS 1755))	-	2000	Wrapping
8.4(Mechanical Properties (as per IS 10810(Part- 42)))	-	2000	Resistance Test
7(Dimensions)	-	1000	Dimension
8.1(Mechanical Properties (as per table 5 of IS 1608))	-	3000	Elongation

Complete

18 Dec, 2027

-
-

485

Kailtech Test and Research Centre Pvt. Ltd.

IS 9103 (1999)

Specification for Concrete Admixtures -

All

35000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4, Table 1A(Slump)	-	3000	Slump
Cl 4, Table 1 B(Flow)	-	5000	Flow
Cl 4, Table 1 B(Loss of workability on standing)	-	5000	Loss of Workability on Standing
Cl 4, Table 1 B(Minimum compressive strength ( 7 Days,28 Days, 6 Month and 1 Year))	-	5000	Time of setting, allowable deviation from control sample hours
Cl 4, Table 1A(Water Content, percent of control sample, Max)	-	5000	Time of setting, allowable deviation from control sample hours
Cl 4, Table 1A(Time of setting, allowable deviation from control sample hours)	-	5000	Time of setting, allowable deviation from control sample hours
Cl 4, Table 1A(Compressive strength, percent of control sample, Min)	-	5000	Compressive strength, percent of control sample
Cl 4, Table 1A(Flexural strength, percent of control sample, Min)	-	5000	Flexural strength, percent of control sample
Cl 4, Table 1A(Length change, percent increase over control sample, Max)	-	5000	Length change, percent increase over control sample
Cl 4, Table 1A(Bleeding, percent increase over control sample, Max)	-	5000	Bleeding, percent increase over control sample
Cl 4, Table 1A(Air content (%), Max, over control)	-	5000	Air content (%), Max, over control
Clause 9, Table- 2( pH)	-	750	pH
Clause 9, Table- 2(Dry material content )	-	1000	Dry Material Content
Clause 9, Table- 2(Ash content)	-	750	Ash Content
Clause 9, Table- 2(Relative density)	-	750	Relative Density
Clause 9, Table- 2(Chloride ion content)	-	1500	Chloride Content
4, Table 1B( minimum Compressive strength percent of control mix concrete 7 days)	-	-	-
Clause 4, Table 1A, SI no. (iii) (Initial time of setting allowable deviation from control sample)	-	-	-
4, Table 1A(Compressive strength percent of control Sample 1 Day )	-	-	-
4, Table 1A(Flexural strength percent of control Sample 3 Day)	-	-	-
4, Table 1A(Length Change percent Increase over control Sample 28 Day)	-	-	-
4, Table 1B( minimum Compressive strength percent of control mix concrete 28 days)	-	-	-
4, Table 1B( minimum Compressive strength percent of control mix concrete 6 Months days)	-	-	-
4, Table 1B( minimum Compressive strength percent of control mix concrete 1 Year )	-	-	-
Clause 4, Table 1A, SI no. (iii) (Final time of setting allowable deviation from control sample)	-	-	-
4, Table 1A(Compressive strength percent of control Sample 3 Days)	-	-	-
4, Table 1A(Compressive strength percent of control Sample 7 Days)	-	-	-
4, Table 1A(Compressive strength percent of control Sample 28 Days )	-	-	-
4, Table 1A(Compressive strength percent of control Sample 6 Months )	-	-	-
4, Table 1A(Compressive strength percent of control Sample 1 year )	-	-	-
4, Table 1A(Flexural strength percent of control Sample 7 Day)	-	-	-
4, Table 1A(Flexural strength percent of control Sample 28 Day)	-	-	-
4, Table 1A(Length Change percent Increase over control Sample 6 Month)	-	-	-
4, Table 1A(Length Change percent Increase over control Sample 1 year)	-	-	-

Complete

18 Dec, 2027

-
-

486

Kailtech Test and Research Centre Pvt. Ltd.

IS 1786 (2008)

High strength deformed steel bars and wires for concretere inforcement - Specification (Fourth Revision)

All

21000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 9.4(Load In Other Direction From Bend)	-	2000	None
Cl 9.3(Load In One Direction)	-	1000	None
Cl 8.1(UTM)	-	3000	None
Cl 7.2(Weight)	-	750	None
Cl 6.1(Length, Width & Thickness)	-	750	None
Cl 5(Deformations and Surface Characteristics)	-	10000	Deformations and Surface Characteristics (Pull Out Test)
4.1(Carbon %)	-	500	Carbon
4.1(Manganese %)	-	500	Manganese
4.1(Sulphur %)	-	500	Sulphur
4.1(Phosphorus %)	-	500	Phosphorous
4.1( Nitrogen%)	-	1500	Nitrogen
4.1(Silicon %)	-	500	Silicon
4.1(Ni)	-	1500	Nickle
4.1(Cr)	-	750	Chromium
4.1(Mo)	-	750	Molybdenum
4.1( Copper %)	-	750	Copper
4.1(V)	-	1500	Vanadium
4.1( Ti)	-	1500	Titanium
4.1( Nb)	-	1500	Niobium
4.1( Aluminium %)	-	500	Aluminium
4.1(Sulphur and phosphorous)	-	500	Sulphur and Phosphorous
4.1(CE)	-	500	Carbon Equivalent
Cl.9.4 & Cl. 9.4.1(Rebend test)	-	2000	Rebend Test
Cl. 9.3, Table 4(Bend Test )	-	1000	Bend Test
Cl. 8.1 Table 3(Tensile Strength (TS))	-	3000	Tensile Test
Cl. 7.2 Table -2 (Nominal Mass)	-	750	Nominal Mass
Cl. 6.1(Nominal Size)	-	750	Nominal Size (Specified Length)
Cl 5(Deformations and Surface Characteristics)	-	500	TS /YS Ratio
Cl. 5 (Cl.5 Mean area of ribs/unit length (Ar), )	-	1000	Mean area of ribs/unit length
Cl. 5 (Cl. 5 - Mean projected area of transverse ribs (1/3 of Ar))	-	1000	Mean projected area of transverse ribs
Cl. 8.1 Table 3(Yield Stress (YS))	-	3000	Yield Stress
Cl. 8.1 Table 3(Elongation, percentage)	-	3000	Elongation
Cl 6.1(Length, Width & Thickness)	-	3000	Maximum Extension
Cl 8.1(UTM)	-	3000	Elongation at maximum Force
Cl 7.2(Weight)	-	1000	Ribs Contributing to Projected Area
Cl 9.4(Load In Other Direction From Bend)	-	1000	Gross Cross Sectional Area
Cl 9.3(Load In One Direction)	-	1000	Visual Inspection
Cl. 4.3(Visual Inspection.)	-	1000	Visual Inspection
5.7(PullOut (Bond Test))	-	5000	Pull Out
8.18.1 Table 3(Total elongation at maximum force)	-	3000	Total elongation at maximum force
Cl. 8.1 Table 3(Maximum Extension)	-	3000	Maximum Extension
Cl. 5.2(Surface Characteristics)	-	1000	Surface Characteristics
Cl. 6.2, 6.3 Table 1(Gross Cross Sectional Area, A)	-	750	Gross Cross Sectional Area
Cl. 5.3 (a)(The ribs contributing the projected area - Longitudinal Ribs)	-	1000	The ribs contributing the projected area - Longitudinal Ribs
Cl. 5.3 (b)(The ribs contributing the projected area - Transverse Ribs)	-	1000	The ribs contributing the projected area - Transverse Ribs
Cl. 8.1 Table 3(TS/YS Ratio)	-	1000	TS/YS Ratio
Cl. 5.7(Date of casting of concrete cubes)	-	1000	Date of casting of concrete cubes
Cl. 5.7(Date of testing of concrete cubes)	-	1000	Date of testing of concrete cubes
Cl. 5.7(Average compressive strength of cubes at 28 days)	-	1000	Average compressive strength of cubes at 28 days
Cl. 5.7(Bond Strength at 0.25 mm slip)	-	5000	Bond Strength at 0.25 mm slip

Complete

18 Dec, 2027

-
-

487

Hi Physix Laboratory India Private Limited

IS 302 : Part 2 : Sec 13 (2024)

Household and Similar Electrical Appliances âSafety Part 2 Particular Requirements Section 13 Deep Fat Fryers, Frying Pans and Similar Appliances (First Revision)

66000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking and instructions)	-	2000	-
8(Protection against access to live parts)	-	2000	-
10(Power input and current)	-	2000	-
11(Heating)	-	4000	-
13.1 &13.2(Leakage current test)	-	1500	-
13.1 &13.3(Electric strength test)	-	1500	-
14(Transient overvoltages)	-	2000	-
15(Moisture resistance)	-	4000	-
15.3(Moisture resistance)	-	0	Testing charges included in Cl.15
15.101(Moisture resistance)	-	0	Testing charges included in Cl.15
16.1 &16.2(Leakage current test)	-	1500	-
16.1 & 16.3(Electric strength test)	-	1500	-
17(Overload protection of transformers and associated circuits)	-	4000	-
19.1 to 19.13, Table No. - 9(Abnormal operation)	-	8000	Charges applicable excluding the test of Cl.19.11.4.1 to Cl.19.11.4.7. The testing charges for EMI/EMC Testing (Cl.19.11.4.1 to Cl.19.11.4.7) will be charged extra.
19.101 to to 19.102(Abnormal operation)	-	0	Testing charges included in Cl.19.1 to CL.19.13
20(Stability and mechanical hazards)	-	2000	-
21(Mechanical strength)	-	3000	-
22(Construction)	-	8000	-
22.101(Construction)	-	0	Testing charges included in Cl.22
23(Internal wiring)	-	2000	-
24(Components)	-	3000	-
25("Supply connection and external flexible cords")	-	1000	-
26("Terminals for external conductors")	-	1000	-
27(Provision for earthing)	-	2000	-
28(Screws and connections)	-	1000	-
29("Clearances, creepage distances and solid insulation")	-	2000	-
30(Resistance to heat and fire)	-	3000	-
31(Resistance to rusting)	-	1000	-
32("Radiation, toxicity and similar hazards")	-	1000	-

Complete

20 Jun, 2028

-
Included w.e.f 25.03.2025 Exclusion: Cl 24 (Components), Cl 32 ("Radiation, toxicity and similar hazards")

488

Unique Test House

IS 9537 : Part 2 (1981)

Specification for conduits for electrical installations: Part 2 rigid steel conduits

ALL GRADE /TYPE/ SIZE

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Marking, IS 9537-2)	-	200	-
6.1(Marking, IS 9537-2)	-	500	-
6.1(Marking, IS 9537-2)	-	500	-
6.3(Marking, Cl. 6.4 of IS 9537-1)	-	500	-
6.2(Marking, IS 9537-2)	-	500	-
7.2.1(Dimensions, (Minimum outside Diameter), IS 9537-2)	-	500	-
7.2.2(Dimensions (Maximum outside Diameter), IS 9537-2)	-	200	-
7.3(Dimensions (Wall thickness), IS 9537-2)	-	200	-
7.3.3(Uniformity of wall thickness, IS 9537-2)	-	300	-
7.4(Screw threads, IS 9537-2)	-	300	-
8.1(Construction, Cl. 8 of IS 9537-1)	-	200	-
8.2(Construction, IS 9537-2)	-	200	-
9.2(Mechanical Properties (Bending test), Cl. 9.3 of IS 9537-1)	-	2000	-
9.3(Mechanical Properties (Compression Test), IS 9537-2)	-	2500	-
13(External Influences, IS 9537-2)	-	200	-
Cl 13.4.5(External Influence ( Outside tube))	-	200	-
Cl 13.4.6(External Influence ( Inside tube))	-	500	-
7.1(Dimensions)	-	500	-

Complete

07 Sep, 2025

-
Included w.e.f. 05.03.2025

489

Conformity Testing Labs Pvt. Ltd. Unit 2

IS 2993 : Part 2 (2024)

a.c. Motor Capacitors Part 2 Motor Start Capacitors ( Third Revision )

375000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.7(Voltage test between the terminals)	-	5000	-
5.1.8(Voltage test between terminals and case)	-	5000	-
5.1.9(Capacitance measurement)	-	5000	-
5.1.10(Check of dimensions)	-	5000	-
5.1.11.1(Robustness of terminations)	-	5000	-
5.1.11.2(Soldering)	-	5000	-
5.1.11.3(Vibration)	-	5000	-
5.1.12(Sealing test)	-	5000	-
5.1.13(Endurance test)	-	120000	-
5.1.14(Damp heat test)	-	120000	-
5.1.15(Self-healing test)	-	20000	-
5.1.16(Destruction test)	-	30000	-
5.1.17.1(Ball-pressure test)	-	20000	-
5.1.17.2(Glow-wire test)	-	5000	-
5.1.17.3(Tracking test)	-	5000	-
5.2(Overloads)	-	5000	-
5.3.2(Terminals and connecting cables)	-	5000	-
5.3.3(Earth connections)	-	5000	-
5.3.4(Discharge devices)	-	5000	-
5.3.5(Pollution)	-	5000	-
5.4(Marking)	-	5000	-
6.1.6(Voltage test between the terminals)	-	5000	-
6.1.7(Voltage test between terminals and case)	-	5000	-
6.1.8(Capacitance and power factor measurement)	-	5000	-
6.1.9(Check of dimensions)	-	5000	-
6.1.10.1(Robustness of terminations)	-	5000	-
6.1.10.2(Soldering)	-	5000	-
6.1.10.3(Vibration)	-	5000	-
6.1.10.4(Fixing bolt or stud (if fitted))	-	5000	-
6.1.10.5(Rapid change of temperature)	-	5000	-
6.1.11(Sealing test)	-	5000	-
6.1.12(Endurance test)	-	120000	-
6.1.13(Damp heat test)	-	120000	-
6.1.14(Pressure relief test)	-	5000	-
6.3.1(Creepage distances and clearances)	-	5000	-
6.4(Marking)	-	5000	-
7.2.1(Measurement of working voltage)	-	5000	-
7.2.2(Influence of capacitance)	-	5000	-
7.3(Checking capacitor temperature)	-	5000	-
7.4(Checking transients)	-	5000	-
7.5(Storage of electrolytic capacitors)	-	5000	-
Annex A(Test voltage)	-	5000	-
5.1.1.1(General)	-	5000	-
5.3.1(Creepage distances and clearances)	-	5000	-
6.1.15.1(Ball-pressure test)	-	20000	-
6.1.15.2(Glow-wire test)	-	25000	-
6.1.15.3(Tracking test)	-	5000	-
6.2(Overloads)	-	5000	-
6.3.2(Terminals and connecting cables)	-	5000	-
6.3.3(Earth connections)	-	5000	-
6.3.4(Discharge devices)	-	5000	-
6.3.5(Pollution)	-	5000	-
6.1.10.4(Fixing bolt or stud (if fitted))	-	5000	-
5.1.10(Check of dimensions)	-	5000	-
5.1.7(Voltage test between the terminals)	-	5000	-
5.1.8(Voltage test between terminals and case)	-	5000	-
5.1.9(Capacitance measurement)	-	5000	-
5.1.10(Check of dimensions)	-	5000	-
5.1.11.1(Robustness of terminations)	-	5000	-
5.1.11.2(Soldering)	-	5000	-
5.1.11.3(Vibration)	-	5000	-
5.1.12(Sealing test)	-	5000	-
5.1.13(Endurance test)	-	100000	-
5.1.14(Damp heat test)	-	120000	-
5.1.15(Self-healing test)	-	20000	-
5.1.16(Destruction test)	-	30000	-
5.1.17.1(Ball-pressure test)	-	20000	-
5.1.17.2(Glow-wire test)	-	5000	-
5.1.17.3(Tracking test)	-	5000	-
5.2(Overloads)	-	5000	-
5.3.2(Terminals and connecting cables)	-	5000	-
5.3.3(Earth connections)	-	5000	-
5.3.4(Discharge devices)	-	5000	-
5.3.5(Pollution)	-	5000	-
5.4(Marking)	-	5000	-
6.1.6(Voltage test between the terminals)	-	5000	-
6.1.7(Voltage test between terminals and case)	-	5000	-
6.1.8(Capacitance and power factor measurement)	-	5000	-
6.1.9(Check of dimensions)	-	5000	-
6.1.10.1(Robustness of terminations)	-	5000	-
6.1.10.2(Soldering)	-	5000	-
6.1.10.3(Vibration)	-	5000	-
6.1.10.4(Fixing bolt or stud (if fitted))	-	5000	-
6.1.10.5(Rapid change of temperature)	-	5000	-
6.1.11(Sealing test)	-	5000	-
6.1.12(Endurance test)	-	100000	-
6.1.13(Damp heat test)	-	120000	-
6.1.14(Pressure relief test)	-	5000	-
6.3.1(Creepage distances and clearances)	-	5000	-
6.4(Marking)	-	5000	-
7.2.1(Measurement of working voltage)	-	5000	-
7.2.2(Influence of capacitance)	-	5000	-
7.3(Checking capacitor temperature)	-	5000	-
7.4(Checking transients)	-	5000	-
7.5(Storage of electrolytic capacitors)	-	5000	-
Annex A(Test voltage)	-	5000	-
5.1.1.1(General)	-	5000	-
5.3.1(Creepage distances and clearances)	-	5000	-
6.1.15.1(Ball-pressure test)	-	20000	-
6.1.15.2(Glow-wire test)	-	5000	-
6.1.15.3(Tracking test)	-	5000	-
6.2(Overloads)	-	5000	-
6.3.2(Terminals and connecting cables)	-	5000	-
6.3.3(Earth connections)	-	5000	-
6.3.4(Discharge devices)	-	5000	-
6.3.5(Pollution)	-	5000	-
6.1.10.4(Fixing bolt or stud (if fitted))	-	5000	-
5.1.10(Check of dimensions)	-	5000	-

Complete

05 Apr, 2027

-
Included w.e.f 25.03.2025

490

Bahadurgarh Footwear Development Services (BFDS)

IS 6721 (2023)

SANDAL AND SLIPPERS SPECIFICATION First revision

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No.4(SHAPE AND DESIGN)	-	200	-
Cl. No.5("SIZE AND FITTINGS ")	-	200	-
Cl. No.6("CONSTRUCTION ")	-	200	-
Cl. No.7(MATERIAL)	-	200	-
Cl. No.8.1, Table no. 1(i),a("Tear strength, (other than moulded upper material) ")	-	450	-
Cl. No.8.1, Table no. 1(i),b("For all moulded upper material ")	-	450	-
Cl. No.8.1, Table no. 1(ii)(Flexing endurance)	-	600	-
Cl. No.8.2,Table no. 2(i)(Tear strength)	-	450	-
Cl. No.8.2,Table no. 2(ii),a("Abrasion resistance- At dry condition")	-	600	-
Cl. No.8.2,Table no. 2(ii),b("Abrasion resistance- At wet condition")	-	600	-
Cl. No.8.3,Table no. 3(i)(Tear strength)	-	450	-
Cl. No.8.3,Table no. 3(ii),a("Abrasion resistance- At dry condition")	-	600	-
Cl. No.8.3,Table no. 3(ii),b("Abrasion resistance- At wet condition")	-	600	-
Cl. No.8.4,Table no. 4(i)(Grain crack index)	-	500	-
Cl. No.8.4,Table no. 4(ii)(Density)	-	200	-
Cl. No.8.4,Table no. 4(iii)(Abrasion resistance)	-	600	-
Cl. No.8.4,Table no. 5(i)(Density)	-	200	-
Cl. No.8.4,Table no. 5(ii)("Abrasion resistance, Volume loss ")	-	600	-
Cl. No.8.4, Table no. 5(iii)("Flexing resistance, At 30 000 flexes")	-	600	-
Cl. No.8.5, Table no. 6(i)("Bond strength, N/mm, Min (Applicable when fore part is fully covered or strap width is more than 25 mm)")	-	500	-
Cl. No.8.5, Table no. 6(ii)("Toe post attachment strength, N, Min (Applicable if toe post is present)")	-	500	-
Cl. No.8.5, Table no. 6(iii)("Toe ring attachment strength, Min (Applicable if toe ring is not integral part of upper")	-	500	-
Cl. No.8.5, Table no. 6(iv)(Strap to outsole strength)	-	500	-
Cl. No.8.5, Table no. 6(v)("Attachment strength of back strap and Buckle/D-ring ")	-	500	-
Cl. No.8.5, Table no. 6(vi)("Attachment strength of elastic, limit of useful extension, percent")	-	500	-
Cl. No.8.5, Table no. 6(vii)("Attachment strength of back strap and velcro, N, Min (If, present)")	-	500	-
Cl. No.8.5, Table no. 6(viii)("Hydrolysis resistance, Cut growth after 150 000 flexes, mm, Max (Applicable for PU sole only)")	-	2000	-
Cl. No.8.5, Table no. 6(ix)("Heel pull off strength, N, Min (Applicable for heel height 40 mm and above attached separately to the sandal/slipper)")	-	500	-
Cl. No.8.5, Table no. 6(x)("Inter layer bond strength, N/mm, (Applicable for multi-layer sole)")	-	500	-
Cl. No.8.5, Table no. 6(xi)("Slip Resistance, Coefficient of Friction (COF) (Not applicable for leather sole) (To be carried out on quarry tiles)")	-	1200	-
Cl. No.9.(MARKING AND PACKING)	-	500	-

Complete

02 Sep, 2027

-
Exclusion: Table 1 xiv Chemical requirement and Table 1 xv Lead content

491

Bahadurgarh Footwear Development Services (BFDS)

IS 10702 (2023)

Hawai Chappal-Specification

6500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Material)	-	200	-
4.2(Length)	-	200	-
4.3(Thickness)	-	200	-
4.4 , Table No. 1 , i)(Density)	-	200	-
4.4 , Table No. 1 , ii)(2Compression set at constant stress)	-	500	-
4.4 , Table No. 1 , iii)(3Split tear strength)	-	450	-
4.4 , Table No. 1 , iv)("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber")	-	600	-
4.4 , Table No. 1 , v)(5Abrasion resistance at applied force)	-	600	-
4.4 , Table No. 1 , vi)(Flexing resistance: Maximum cut growth at 50 000 flexes)	-	600	-
4.4 , Table No. 1 , vii)(7 Hydrolysis resistance, Maximum cut growth at 50 000 flexes)	-	2000	-
4.4 , Table No . 2 , i)(Density , Solid strap, Cellular strap)	-	200	-
4.4 , Table No . 2 , ii)("Breaking strength , Strap to strap and Toe portion to strap , Elongation at break")	-	450	-
4.4 , Table No . 2 , iii)(Minimum cross section of the stud)	-	500	-
4.4 , Table No . 2 , iv)(Stud bolt)	-	200	-
4.4 , Table No . 3 , i)(Toe post attachment strength)	-	500	-
4.4 , Table No . 3 , ii)(Attachment strength of rear strap)	-	500	-
4.4 , Table No . 3 , iii)(Inter layer bond strength)	-	500	-
6(MARKING AND PACKING)	-	500	-
Cl. No.5.1,Table no.1 of IS 17011(iv)(Chromium (VI))	-	600	-
Cl. No.5.1,Table no.1 of IS 17011(x)(pH)	-	400	-
Clause 4.1 - 4.1.1(Bottom Material)	-	200	-
Clause 4.1 - 4.1.2(Strap Material)	-	200	-
Clause 4.1 - 4.1.4(Material)	-	200	-
Clause 4.2(Material)	-	200	-
Clause 4.3 - 4.3.1(Thickness)	-	200	-
Clause 4.3 - 4.3.2(Thickness)	-	200	-
Clause 4.4 Table 1 -i)(Density, g/cm3, Min)	-	200	-
Clause 4.4 Table 2 -i) - b(Density, g/cm3 Cellular strap)	-	200	-
Clause 4.4 Table 1 -iii)(Split tear strength, kg, Min)	-	450	-
Clause 4.4 Table 1 -iv) - a("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, percent, Max")	-	600	-
Clause 4.4 Table 1 -iv) - b(Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber, percent, Max)	-	600	-
Clause 4.4 Table 1 -v)(Abrasion resistance at applied force 5 N)	-	600	-
Clause 4.4 Table 2 -i) - a("Density, g/cm3 Solid strap ")	-	200	-
Clause 4.4 Table 2 -ii) - a - 1("Breaking strength, kgf, Min Strap to strap(Solid Strap)")	-	450	-
Clause 4.4 Table 2 -ii) - a - 2("Breaking strength, kgf, Min Strap to strap(Cellular Strap)")	-	450	-
Clause 4.4 Table 2 -ii) - a - 3("Breaking strength, kgf, Min Toe portion to strap(Solid Strap)")	-	450	-
Clause 4.4 Table 2 -ii) - a - 4("Breaking strength, kgf, Min Toe portion to strap(Cellular Strap)")	-	450	-
Clause 4.4 Table 2 -ii) - b - 1("Elongation at break, percent (Applicable to strap to strap (V shape) Solid Strap")	-	450	-
Clause 4.4 Table 2 -ii) - b - 2("Elongation at break, percent (Applicable to strap to strap (V shape) Cellular Strap")	-	450	-
Clause 4.4 Table 2 -iii) - a("Minimum cross section of the stud, mm, Size 1 to 13 (Adult)")	-	200	-
Clause 4.4 Table 2 -iii) - b("Minimum cross section of the stud, mm, Size 3 to 13 (Children)")	-	200	-
Clause 4.4 Table 2 -iv) - a("Stud bolt, mm Diameter/edge to edge length")	-	200	-
Clause 4.4 Table 2 -iv) - b("Stud bolt, mm Thickness")	-	200	-
Clause 4.4 Table 3 -i)("Toe post attachment strength, N, Min")	-	450	-
Clause 4.4 Table 3 -iii)("Inter layer bond strength, N/mm, Min")	-	500	-
Clause 4.1 - 4.1.3(Material)	-	200	-
Clause 4.4 Table 3 -ii)("Attachment strength of rear strap, N, Min")	-	450	-
4.1(Material)	-	200	-
4.2(Length)	-	200	-
4.3(Thickness)	-	200	-
4.4 , Table No. 1 , i)(Density)	-	200	-
4.4 , Table No. 1 , ii)(2Compression set at constant stress)	-	500	-
4.4 , Table No. 1 , iii)(3Split tear strength)	-	450	-
4.4 , Table No. 1 , iv)("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber")	-	600	-
4.4 , Table No. 1 , v)(5Abrasion resistance at applied force)	-	600	-
4.4 , Table No. 1 , vi)(Flexing resistance: Maximum cut growth at 50 000 flexes)	-	600	-
4.4 , Table No. 1 , vii)(7 Hydrolysis resistance, Maximum cut growth at 50 000 flexes)	-	2000	-
4.4 , Table No . 2 , i)(Density , Solid strap, Cellular strap)	-	200	-
4.4 , Table No . 2 , ii)("Breaking strength , Strap to strap and Toe portion to strap , Elongation at break")	-	500	-
4.4 , Table No . 2 , iii)(Minimum cross section of the stud)	-	200	-
4.4 , Table No . 2 , iv)(Stud bolt)	-	200	-
4.4 , Table No . 3 , i)(Toe post attachment strength)	-	500	-
4.4 , Table No . 3 , ii)(Attachment strength of rear strap)	-	500	-
4.4 , Table No . 3 , iii)(Inter layer bond strength)	-	500	-
6(MARKING AND PACKING)	-	200	-
Cl. No.5.1,Table no.1 of IS 17011(iv)(Chromium (VI))	-	800	-
Cl. No.5.1,Table no.1 of IS 17011(x)(pH)	-	500	-
Clause 4.1 - 4.1.1(Bottom Material)	-	200	-
Clause 4.1 - 4.1.2(Strap Material)	-	200	-
Clause 4.1 - 4.1.4(Material)	-	200	-
Clause 4.2(Material)	-	200	-
Clause 4.3 - 4.3.1(Thickness)	-	200	-
Clause 4.3 - 4.3.2(Thickness)	-	200	-
Clause 4.4 Table 1 -i)(Density, g/cm3, Min)	-	200	-
Clause 4.4 Table 2 -i) - b(Density, g/cm3 Cellular strap)	-	200	-
Clause 4.4 Table 1 -iii)(Split tear strength, kg, Min)	-	450	-
Clause 4.4 Table 1 -iv) - a("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, percent, Max")	-	600	-
Clause 4.4 Table 1 -iv) - b(Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber, percent, Max)	-	600	-
Clause 4.4 Table 1 -v)(Abrasion resistance at applied force 5 N)	-	600	-
Clause 4.4 Table 2 -i) - a("Density, g/cm3 Solid strap ")	-	200	-
Clause 4.4 Table 2 -ii) - a - 1("Breaking strength, kgf, Min Strap to strap(Solid Strap)")	-	500	-
Clause 4.4 Table 2 -ii) - a - 2("Breaking strength, kgf, Min Strap to strap(Cellular Strap)")	-	500	-
Clause 4.4 Table 2 -ii) - a - 3("Breaking strength, kgf, Min Toe portion to strap(Solid Strap)")	-	500	-
Clause 4.4 Table 2 -ii) - a - 4("Breaking strength, kgf, Min Toe portion to strap(Cellular Strap)")	-	500	-
Clause 4.4 Table 2 -ii) - b - 1("Elongation at break, percent (Applicable to strap to strap (V shape) Solid Strap")	-	450	-
Clause 4.4 Table 2 -ii) - b - 2("Elongation at break, percent (Applicable to strap to strap (V shape) Cellular Strap")	-	450	-
Clause 4.4 Table 2 -iii) - a("Minimum cross section of the stud, mm, Size 1 to 13 (Adult)")	-	200	-
Clause 4.4 Table 2 -iii) - b("Minimum cross section of the stud, mm, Size 3 to 13 (Children)")	-	200	-
Clause 4.4 Table 2 -iv) - a("Stud bolt, mm Diameter/edge to edge length")	-	200	-
Clause 4.4 Table 2 -iv) - b("Stud bolt, mm Thickness")	-	200	-
Clause 4.4 Table 3 -i)("Toe post attachment strength, N, Min")	-	500	-
Clause 4.4 Table 3 -iii)("Inter layer bond strength, N/mm, Min")	-	500	-
Clause 4.1 - 4.1.3(Material)	-	200	-
Clause 4.4 Table 3 -ii)("Attachment strength of rear strap, N, Min")	-	500	-
4.4 , Table No. 1 , vi)(Flexing resistance: Maximum cut growth at 50 000 flexes)	-	800	-
4.4 , Table No. 1 , vii)(7 Hydrolysis resistance, Maximum cut growth at 50 000 flexes)	-	2500	-
4.4 , Table No . 2 , ii)("Breaking strength , Strap to strap and Toe portion to strap , Elongation at break")	-	450	-
6(MARKING AND PACKING)	-	500	-
Clause 4.4 Table 1 -iv) - a("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, percent, Max")	-	800	-
Clause 4.4 Table 1 -iv) - b(Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber, percent, Max)	-	800	-
Clause 4.4 Table 2 -ii) - b - 1("Elongation at break, percent (Applicable to strap to strap (V shape) Solid Strap")	-	500	-
Clause 4.4 Table 2 -ii) - b - 2("Elongation at break, percent (Applicable to strap to strap (V shape) Cellular Strap")	-	500	-
Clause 4.4 Table 2 -iii) - a("Minimum cross section of the stud, mm, Size 1 to 13 (Adult)")	-	500	-
Clause 4.4 Table 2 -iii) - b("Minimum cross section of the stud, mm, Size 3 to 13 (Children)")	-	500	-
Clause 4.4 Table 2 -iv) - a("Stud bolt, mm Diameter/edge to edge length")	-	500	-
Cl-4 ((Amendment No-1)(Category And Type)	-	200	-
Cl-4.4, Table -1 S. No-1 (i) (Amendment No-1)(Compression set at constant stress)	-	500	-
Cl-4.4, Table -1 S. No-1 (ii) (Amendment No-1)(Split tear strength)	-	450	-
Cl-4.4, Table -1 S. No-1 (iii) (a)(Amendment No-1)("Shrinkage at Shrinkage at 50 °C ± 1 °C for 2 h for polymeric material, percent, Max ")	-	800	-
Cl-4.4, Table -1 S. No-1 (iii)(b) (Amendment No-1)(Shrinkage at 100 °C ± 1 °C for 1 h for rubber, percent, Max)	-	800	-
Cl-4.4, Table -1 S. No-1 (iv) (Amendment No-1)(Abrasion resistance at applied force)	-	600	-
Cl-4.4, Table -1 S. No-1 (v) (Amendment No-1)(Flexing resistance: Maximum cut growth,)	-	600	-
Cl-4.4, Table -1 S. No-1 (vi) (Amendment No-1)(Hydrolysis resistance:Maximum cut growth)	-	2500	-
Cl-4.4, Table -2 S. No-1 (i), a (Amendment No-1)("Breaking strength for Strap to strap 1-Solid strap 2-Cellular strap")	-	500	-
Cl-4.4, Table -2 S. No-1 (i), b (Amendment No-1)("Breaking strength for Toe portion to strap 1-Solid strap 2-Cellular strap")	-	500	-
Cl-4.4, Table -2 S. No-1 (i), c (Amendment No-1)("Elongation at break , percent, Min 1-Solid strap 2-Cellular strap")	-	450	-
Cl-4.4, Table -3 S. No-1 (i), (Amendment No-1)(Toe post attachment strength)	-	500	-
Cl-4.4, Table -3 S. No-1 (ii), (Amendment No-1)(Attachment strength of rear strap)	-	500	-
Cl-4.4, Table -3 S. No-1 (iii), (Amendment No-1)(Inter layer bond strength)	-	500	-
4.4 , Table No. 1 , iv)("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber")	-	800	-
Clause 4.4 Table 2 -ii) - a - 1("Breaking strength, kgf, Min Strap to strap(Solid Strap)")	-	450	-
Clause 4.4 Table 2 -ii) - a - 2("Breaking strength, kgf, Min Strap to strap(Cellular Strap)")	-	450	-
Clause 4.4 Table 2 -ii) - a - 3("Breaking strength, kgf, Min Toe portion to strap(Solid Strap)")	-	450	-
Clause 4.4 Table 2 -ii) - a - 4("Breaking strength, kgf, Min Toe portion to strap(Cellular Strap)")	-	450	-
Clause 4.4 Table 3 -ii)("Attachment strength of rear strap, N, Min")	-	450	-
Cl-4 ((Amendment No-1)(Category And Type)	-	450	-
Cl-4.4, Table -1 S. No-1 (i) (Amendment No-1)(Compression set at constant stress)	-	500	-
Cl-4.4, Table -1 S. No-1 (ii) (Amendment No-1)(Split tear strength)	-	450	-
Cl-4.4, Table -1 S. No-1 (iii) (a)(Amendment No-1)("Shrinkage at Shrinkage at 50 °C ± 1 °C for 2 h for polymeric material, percent, Max ")	-	800	-
Cl-4.4, Table -1 S. No-1 (iii)(b) (Amendment No-1)(Shrinkage at 100 °C ± 1 °C for 1 h for rubber, percent, Max)	-	800	-
Cl-4.4, Table -1 S. No-1 (iv) (Amendment No-1)(Abrasion resistance at applied force)	-	600	-
Cl-4.4, Table -1 S. No-1 (v) (Amendment No-1)(Flexing resistance: Maximum cut growth,)	-	800	-
Cl-4.4, Table -1 S. No-1 (vi) (Amendment No-1)(Hydrolysis resistance:Maximum cut growth)	-	2500	-
Cl-4.4, Table -2 S. No-1 (i), a (Amendment No-1)("Breaking strength for Strap to strap 1-Solid strap 2-Cellular strap")	-	450	-
Cl-4.4, Table -2 S. No-1 (i), b (Amendment No-1)("Breaking strength for Toe portion to strap 1-Solid strap 2-Cellular strap")	-	450	-
Cl-4.4, Table -2 S. No-1 (i), c (Amendment No-1)("Elongation at break , percent, Min 1-Solid strap 2-Cellular strap")	-	450	-
Cl-4.4, Table -3 S. No-1 (i), (Amendment No-1)(Toe post attachment strength)	-	500	-
Cl-4.4, Table -3 S. No-1 (ii), (Amendment No-1)(Attachment strength of rear strap)	-	450	-
Cl-4.4, Table -3 S. No-1 (iii), (Amendment No-1)(Inter layer bond strength)	-	500	-
4.4 , Table No . 2 , iii)(Minimum cross section of the stud)	-	500	-
Clause 4.1 - 4.1.2(Strap Material)	-	450	-
Clause 4.4 Table 2 -iii) - a("Minimum cross section of the stud, mm, Size 1 to 13 (Adult)")	-	450	-
Clause 4.4 Table 2 -iii) - b("Minimum cross section of the stud, mm, Size 3 to 13 (Children)")	-	450	-
Cl-4 ((Amendment No-1)(Category And Type)	-	200	-
Cl-4.4, Table -1 S. No-1 (v) (Amendment No-1)(Flexing resistance: Maximum cut growth,)	-	600	-
Cl-4.4, Table -3 S. No-1 (ii), (Amendment No-1)(Attachment strength of rear strap)	-	500	-
4.1(Material)	-	-	-
4.2(Length)	-	-	-
4.3(Thickness)	-	-	-
4.4 , Table No. 1 , i)(Density)	-	-	-
4.4 , Table No. 1 , ii)(2Compression set at constant stress)	-	-	-
4.4 , Table No. 1 , iii)(3Split tear strength)	-	-	-
4.4 , Table No. 1 , iv)("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber")	-	-	-
4.4 , Table No. 1 , v)(5Abrasion resistance at applied force)	-	-	-
4.4 , Table No. 1 , vi)(Flexing resistance: Maximum cut growth at 50 000 flexes)	-	-	-
4.4 , Table No. 1 , vii)(7 Hydrolysis resistance, Maximum cut growth at 50 000 flexes)	-	-	-
4.4 , Table No . 2 , i)(Density , Solid strap, Cellular strap)	-	-	-
4.4 , Table No . 2 , ii)("Breaking strength , Strap to strap and Toe portion to strap , Elongation at break")	-	-	-
4.4 , Table No . 2 , iii)(Minimum cross section of the stud)	-	-	-
4.4 , Table No . 2 , iv)(Stud bolt)	-	-	-
4.4 , Table No . 3 , i)(Toe post attachment strength)	-	-	-
4.4 , Table No . 3 , ii)(Attachment strength of rear strap)	-	-	-
4.4 , Table No . 3 , iii)(Inter layer bond strength)	-	-	-
6(MARKING AND PACKING)	-	-	-
Cl. No.5.1,Table no.1 of IS 17011(iv)(Chromium (VI))	-	-	-
Cl. No.5.1,Table no.1 of IS 17011(x)(pH)	-	-	-
Clause 4.1 - 4.1.1(Bottom Material)	-	-	-
Clause 4.1 - 4.1.2(Strap Material)	-	-	-
Clause 4.1 - 4.1.4(Material)	-	-	-
Clause 4.2(Material)	-	-	-
Clause 4.3 - 4.3.1(Thickness)	-	-	-
Clause 4.3 - 4.3.2(Thickness)	-	-	-
Clause 4.4 Table 1 -i)(Density, g/cm3, Min)	-	-	-
Clause 4.4 Table 2 -i) - b(Density, g/cm3 Cellular strap)	-	-	-
Clause 4.4 Table 1 -iii)(Split tear strength, kg, Min)	-	-	-
Clause 4.4 Table 1 -iv) - a("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, percent, Max")	-	-	-
Clause 4.4 Table 1 -iv) - b(Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber, percent, Max)	-	-	-
Clause 4.4 Table 1 -v)(Abrasion resistance at applied force 5 N)	-	-	-
Clause 4.4 Table 2 -i) - a("Density, g/cm3 Solid strap ")	-	-	-
Clause 4.4 Table 2 -ii) - a - 1("Breaking strength, kgf, Min Strap to strap(Solid Strap)")	-	-	-
Clause 4.4 Table 2 -ii) - a - 2("Breaking strength, kgf, Min Strap to strap(Cellular Strap)")	-	-	-
Clause 4.4 Table 2 -ii) - a - 3("Breaking strength, kgf, Min Toe portion to strap(Solid Strap)")	-	-	-
Clause 4.4 Table 2 -ii) - a - 4("Breaking strength, kgf, Min Toe portion to strap(Cellular Strap)")	-	-	-
Clause 4.4 Table 2 -ii) - b - 1("Elongation at break, percent (Applicable to strap to strap (V shape) Solid Strap")	-	-	-
Clause 4.4 Table 2 -ii) - b - 2("Elongation at break, percent (Applicable to strap to strap (V shape) Cellular Strap")	-	-	-
Clause 4.4 Table 2 -iii) - a("Minimum cross section of the stud, mm, Size 1 to 13 (Adult)")	-	-	-
Clause 4.4 Table 2 -iii) - b("Minimum cross section of the stud, mm, Size 3 to 13 (Children)")	-	-	-
Clause 4.4 Table 2 -iv) - a("Stud bolt, mm Diameter/edge to edge length")	-	-	-
Clause 4.4 Table 2 -iv) - b("Stud bolt, mm Thickness")	-	-	-
Clause 4.4 Table 3 -i)("Toe post attachment strength, N, Min")	-	-	-
Clause 4.4 Table 3 -iii)("Inter layer bond strength, N/mm, Min")	-	-	-
Clause 4.1 - 4.1.3(Material)	-	-	-
Clause 4.4 Table 3 -ii)("Attachment strength of rear strap, N, Min")	-	-	-
Cl-4 ((Amendment No-1)(Category And Type)	-	-	-
Cl-4.4, Table -1 S. No-1 (i) (Amendment No-1)(Compression set at constant stress)	-	-	-
Cl-4.4, Table -1 S. No-1 (ii) (Amendment No-1)(Split tear strength)	-	-	-
Cl-4.4, Table -1 S. No-1 (iii) (a)(Amendment No-1)("Shrinkage at Shrinkage at 50 °C ± 1 °C for 2 h for polymeric material, percent, Max ")	-	-	-
Cl-4.4, Table -1 S. No-1 (iii)(b) (Amendment No-1)(Shrinkage at 100 °C ± 1 °C for 1 h for rubber, percent, Max)	-	-	-
Cl-4.4, Table -1 S. No-1 (iv) (Amendment No-1)(Abrasion resistance at applied force)	-	-	-
Cl-4.4, Table -1 S. No-1 (v) (Amendment No-1)(Flexing resistance: Maximum cut growth,)	-	-	-
Cl-4.4, Table -1 S. No-1 (vi) (Amendment No-1)(Hydrolysis resistance:Maximum cut growth)	-	-	-
Cl-4.4, Table -2 S. No-1 (i), a (Amendment No-1)("Breaking strength for Strap to strap 1-Solid strap 2-Cellular strap")	-	-	-
Cl-4.4, Table -2 S. No-1 (i), b (Amendment No-1)("Breaking strength for Toe portion to strap 1-Solid strap 2-Cellular strap")	-	-	-
Cl-4.4, Table -2 S. No-1 (i), c (Amendment No-1)("Elongation at break , percent, Min 1-Solid strap 2-Cellular strap")	-	-	-
Cl-4.4, Table -3 S. No-1 (i), (Amendment No-1)(Toe post attachment strength)	-	-	-
Cl-4.4, Table -3 S. No-1 (ii), (Amendment No-1)(Attachment strength of rear strap)	-	-	-
Cl-4.4, Table -3 S. No-1 (iii), (Amendment No-1)(Inter layer bond strength)	-	-	-

Complete

02 Sep, 2027

-
Exclusion: Table 1 vii and Table 2 ii Chemical requirements, Table 1 viii and Table 2 iii Lead content

492

Bahadurgarh Footwear Development Services (BFDS)

IS 15844 : Part 1 (2023)

SPORTS FOOTWEAR PART -1 GENERAL PURPOSEFirst Revision

22000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl No.4.1(Sampling and Conditioning)	-	500	-
Cl No.4.2(Construction)	-	300	-
Cl No.4.3(Whole Footwear)	-	300	-
4.3.1(Insole)	-	300	-
4.3.2(Toe spring height)	-	500	-
4.3.3(Upper to Mid Sole/Out Sole Bond Performance)	-	500	-
4.3.4("Upper to Composite Sole Bond Performance (Applicable Only When the Sole is Composite)")	-	500	-
4.3.5(Out Sole to Mid Sole (Multilayer) Bond Performance)	-	500	-
4.3.6(Energy Absorption at Seat Region)	-	800	-
4.3.7(Complete Shoe Flexing)	-	640	-
4.3.8(Washability)	-	800	-
4.3.9(Slip Resistance)	-	1000	-
Cl No.4.4 , Table No. 2 , i) , a)(Flexing resistance, Dry condition)	-	600	-
Cl No.4.4 , Table No. 2 , ii)(Tear strength (average force), Min, N)	-	450	-
Cl No.4.4 , Table No. 2 , iii) , a)("Colour fastness rubbing (To and fro) Grey scale rate, Min , Dry: (rubbing) Rating: (Marring and staining) ")	-	600	-
Cl No.4.4 , Table No. 2 , iii) , b)("Colour fastness rubbing (To and fro) Grey scale rate, Min , Wet: (rubbing) Rating: (Marring and staining)")	-	600	-
Cl No.4.4 , Table No. 2 , iv) , a)(Water vapour permeability, mg/cm2h, Min)	-	800	-
Cl No.4.4 , Table No. 2 , iv) , b)(Water vapour coefficient, mg/cm2 , Min)	-	800	-
Cl No.4.4 , Table No. 2 , v)(Stitch tear strength (double hole), N/mm, Min)	-	600	-
Cl No.4.4 , Table No. 2 , i)(Breaking strength, N/mm, Min)	-	450	-
Cl No.4.4 , Table No. 2 , ii)(Elongation at break, percent Min)	-	450	-
Cl No.4.4 , Table No. 2 , iii)(Tear strength, N, Min For Fabric: For all other materials)	-	450	-
Cl No.4.4 , Table No. 2 , iv) , a)(Flexing resistance, Dry condition)	-	600	-
Cl No.4.4 , Table No. 2 , iv) , b)(Flexing resistance, ,Wet condition)	-	600	-
Cl No.4.4 , Table No. 2 , v) , a)(Water vapour permeability, mg/cm2h, Min)	-	800	-
Cl No.4.4 , Table No. 2 , v) , b)("Water vapour coefficient, mg/cm2 , Min ")	-	800	-
Cl No.4.4 , Table No. 2 , vi)(Hydrolysis resistance)	-	2000	-
Cl No.4.4 , Table No. 2 , vii)(Bursting Strength, kg/cm2 , Min)	-	500	-
Cl No.4.5 , Table No. 3 , i)(Tear strength, N, Min)	-	450	-
Cl No.4.5 , Table No. 3 , ii)(Abrasion resistance, cycles)	-	600	-
Cl No.4.5 , Table No. 3 , iii)("Colour fastness to rubbing (crocking), Grey scale rate with 10 rubs on dry or wet, Min")	-	600	-
Cl No.4.5 , Table No. 3 , iv)("Colour fastness to perspiration (contact method) Grey scale rate, Min")	-	600	-
Cl No.4.5 , Table No. 3 , v) , a)(Water vapour permeability, mg/cm2h, Min)	-	800	-
Cl No.4.5 , Table No. 3 , v) , b)("Water vapour coefficient, mg/cm2 , Min ")	-	800	-
Cl No.4.6 , Table No. 4 , i)(Thickness, mm, Min)	-	200	-
Cl No.4.6 , Table No. 4 , ii)(Flexing index, Min)	-	800	-
Cl No.4.6 , Table No. 4 , iii)(Abrasion resistance, at 400 cycles)	-	800	-
Cl No.4.6 , Table No. 4 , iv) , a)(Water Absorption, mg/cm2 , Min)	-	800	-
Cl No.4.6 , Table No. 4 , iv) , b)(Water Desorption, percent, Min)	-	800	-
Cl No.4.7, Table No. 5 , i)(Thickness, mm, Min)	-	200	-
Cl No.4.7, Table No. 5 , ii)(Abrasion resistance, cycles)	-	600	-
Cl No.4.7, Table No. 5 , iii) , a)(Water Absorption, mg/cm2 , Min)	-	800	-
Cl No.4.7, Table No. 5 , iii) , b)(Water Desorption, percent, Min)	-	800	-
Cl No.4.8 , Table No. 6 , i)(Abrasion resistance (Volume loss), mm3 , Max)	-	600	-
Cl No.4.8 , Table No. 6 , ii)("Flexing resistance Belt Method at 90 diameter Mandrel or Bennewart method, cut growth, Max")	-	600	-
Cl No.4.8 , Table No. 6 , iii)("Hydrolysis resistance, cut growth after 150 000 flexes, in mm, Max")	-	2000	-
Cl No.4.9 , Table No. 7 , i)(Compression set, percent, Max)	-	500	-
Cl No.4.9 , Table No. 7 , ii)(Split tear strength, kg/25 mm, Min)	-	450	-
Cl No.4.9 , Table No. 7 , iii)(Heat shrinkage, percent, Max)	-	800	-
Cl No.4.10 , Table No. 8 , i)(First dry collapsing load, hardness, N, Min)	-	800	-
Cl No.4.10 , Table No. 8 , ii)(Resilience, percent, Min)	-	800	-
Cl No.4.10 , Table No. 8 , iii)(Moisture resistance, percent, Min)	-	800	-
Cl No.4.10 , Table No. 8 , iv) , a)(Initial dry area shape retention, percent, Min)	-	800	-
Cl No.4.10 , Table No. 8 , iv) , b)(Area shape retention after 10th collapse, dry, percent, Min)	-	800	-
Cl No.4.11 , Table No. 9 , i)(Peel strength, N/mm, Min)	-	500	-
Cl No.4.11 , Table No. 9 , ii)(Shear strength, kPa , Min)	-	600	-
Cl No.4.12 , Table No. 10 , i)(Limit of useful extension, percent, Min)	-	600	-
Cl No.4.13 , Table No. 11 , i)(Breaking strength of lace, N, Min)	-	500	-
Cl No.4.13 , Table No. 11 , ii)(Lace tag strength, N, Min)	-	500	-
Cl No.4.13 , Table No. 11 , iii)(Lace to lace abrasion,)	-	800	-
Cl No.4.13 , Table No. 11 , iv)("Colour fastness to water Gray Scale Rate, Min Rating")	-	600	-
Cl No.4.13 , Table No. 11 , v)(Strength of Buckle/Ski hook, N, Min)	-	600	-
Cl No.4.13 , Table No. 11 , vi)(Corrosion resistance)	-	600	-
Cl No . 5(MARKING AND PACKING)	-	1000	-
Cl No . 4.14, Table no. 1 of IS 17011(iv)(Chromium (VI))	-	600	-
Cl No . 4.14, Table no. 1 of IS 17011(x)(pH)	-	400	-
Clause 4.2 - 4.2.1(Construction)	-	200	-
Clause 4.2 - 4.2.2(Construction)	-	200	-
Clause 4.3 - 4.3.1(Whole Footwear)	-	200	-
Clause 4.3 - 4.3.2(Whole Footwear)	-	200	-
Clause 4.3 - 4.3.3(Upper to Mid Sole/Out Sole Bond Performance)	-	500	-
Clause 4.3 - 4.3.4(Upper to Composite Sole Bond Performance(Applicable Only When the Sole is Composite))	-	500	-
Clause 4.3 - 4.3.5(Out Sole to Mid Sole (Multilayer) Bond)	-	500	-
Clause 4.3 - 4.3.7(Complete Shoe Flexing)	-	640	-
Clause 4.4, Table 1 ii)(Tear strength)	-	450	-
Clause 4.4, Table 1 iv)-a(Water Vapour Permeability)	-	800	-
Clause 4.5, Table 3 v)-b(Water Vapour Coeffecient)	-	800	-
Clause 4.4, Table 1 v)(Stitch Tear Strength(Double Hole))	-	600	-
Clause 4.4, Table 2 i)(Breaking Strength)	-	450	-
Clause 4.4, Table 2 ii)(Elongation at break)	-	450	-
Clause 4.4, Table 2 iii)(Tear strength)	-	450	-
Clause 4.4, Table 2 v)-a(Water Vapour Permeability)	-	800	-
Clause 4.4, Table 2 v)-b(Water Vapour Coeffecient)	-	800	-
Clause 4.5, Table 3 i)(Tear strength)	-	450	-
Clause 4.5, Table 3 ii)(Abrasion Resistance)	-	600	-
Clause 4.5, Table 3 v)-a(Water Vapour Permeability)	-	800	-
Clause 4.6, Table 4 i)(Thickness)	-	200	-
Clause 4.6, Table 4 ii)(Abrasion Resistance)	-	600	-
Clause 4.6, Table 4 iv)-a(Water Absorption)	-	800	-
Clause 4.6, Table 4 iv)-b(Water Desorption)	-	800	-
Clause 4.8, Table 6 i)(Abrasion Resistance)	-	600	-
Clause 4.8, Table 6 ii)(Flexing Resistance)	-	600	-
Clause 4.8, Table 6 iii)(Hydrolysis Resistance)	-	2000	-
Clause 4.9, Table 7 ii)(Split Tear strength)	-	450	-
Clause 4.9, Table 7 iii)(Heat shrinkage)	-	800	-
Clause 4.4, Table 1 iv)-b(Water Vapour Coeffecient)	-	800	-
Clause 4.7, Table 5 i)(Thickness)	-	200	-
Clause 4.7, Table 5 iii)-a(Water Absorption)	-	800	-
Cl No.4.4 , Table No. 2 , i) , b)(Flexing resistance, Wet condition)	-	600	-
Clause 4.7, Table 5 ii)(Abrasion Resistance)	-	600	-
Clause 4.7, Table 5 iii)-b(Water Desorption)	-	800	-
Cl No.4.1(Sampling and Conditioning)	-	200	-
Cl No.4.2(Construction)	-	200	-
Cl No.4.3(Whole Footwear)	-	200	-
4.3.1(Insole)	-	200	-
4.3.2(Toe spring height)	-	200	-
4.3.3(Upper to Mid Sole/Out Sole Bond Performance)	-	500	-
4.3.4("Upper to Composite Sole Bond Performance (Applicable Only When the Sole is Composite)")	-	500	-
4.3.5(Out Sole to Mid Sole (Multilayer) Bond Performance)	-	500	-
4.3.6(Energy Absorption at Seat Region)	-	800	-
4.3.7(Complete Shoe Flexing)	-	640	-
4.3.9(Slip Resistance)	-	1500	-
Cl No.4.4 , Table No. 2 , i) , a)(Flexing resistance, Dry condition)	-	600	-
Cl No.4.4 , Table No. 2 , ii)(Tear strength (average force), Min, N)	-	450	-
Cl No.4.4 , Table No. 2 , iii) , a)("Colour fastness rubbing (To and fro) Grey scale rate, Min , Dry: (rubbing) Rating: (Marring and staining) ")	-	500	-
Cl No.4.4 , Table No. 2 , iii) , b)("Colour fastness rubbing (To and fro) Grey scale rate, Min , Wet: (rubbing) Rating: (Marring and staining)")	-	500	-
Cl No.4.4 , Table No. 2 , iv) , a)(Water vapour permeability, mg/cm2h, Min)	-	800	-
Cl No.4.4 , Table No. 2 , iv) , b)(Water vapour coefficient, mg/cm2 , Min)	-	800	-
Cl No.4.4 , Table No. 2 , v)(Stitch tear strength (double hole), N/mm, Min)	-	450	-
Cl No.4.4 , Table No. 2 , i)(Breaking strength, N/mm, Min)	-	450	-
Cl No.4.4 , Table No. 2 , ii)(Elongation at break, percent Min)	-	450	-
Cl No.4.4 , Table No. 2 , iii)(Tear strength, N, Min For Fabric: For all other materials)	-	450	-
Cl No.4.4 , Table No. 2 , iv) , a)(Flexing resistance, Dry condition)	-	600	-
Cl No.4.4 , Table No. 2 , iv) , b)(Flexing resistance, ,Wet condition)	-	600	-
Cl No.4.4 , Table No. 2 , v) , a)(Water vapour permeability, mg/cm2h, Min)	-	800	-
Cl No.4.4 , Table No. 2 , v) , b)("Water vapour coefficient, mg/cm2 , Min ")	-	800	-
Cl No.4.4 , Table No. 2 , vi)(Hydrolysis resistance)	-	2500	-
Cl No.4.4 , Table No. 2 , vii)(Bursting Strength, kg/cm2 , Min)	-	600	-
Cl No.4.5 , Table No. 3 , i)(Tear strength, N, Min)	-	450	-
Cl No.4.5 , Table No. 3 , ii)(Abrasion resistance, cycles)	-	600	-
Cl No.4.5 , Table No. 3 , iii)("Colour fastness to rubbing (crocking), Grey scale rate with 10 rubs on dry or wet, Min")	-	500	-
Cl No.4.5 , Table No. 3 , iv)("Colour fastness to perspiration (contact method) Grey scale rate, Min")	-	500	-
Cl No.4.5 , Table No. 3 , v) , a)(Water vapour permeability, mg/cm2h, Min)	-	800	-
Cl No.4.5 , Table No. 3 , v) , b)("Water vapour coefficient, mg/cm2 , Min ")	-	800	-
Cl No.4.6 , Table No. 4 , i)(Thickness, mm, Min)	-	200	-
Cl No.4.6 , Table No. 4 , ii)(Flexing index, Min)	-	600	-
Cl No.4.6 , Table No. 4 , iii)(Abrasion resistance, at 400 cycles)	-	600	-
Cl No.4.6 , Table No. 4 , iv) , a)(Water Absorption, mg/cm2 , Min)	-	800	-
Cl No.4.6 , Table No. 4 , iv) , b)(Water Desorption, percent, Min)	-	800	-
Cl No.4.7, Table No. 5 , i)(Thickness, mm, Min)	-	200	-
Cl No.4.7, Table No. 5 , ii)(Abrasion resistance, cycles)	-	800	-
Cl No.4.7, Table No. 5 , iii) , a)(Water Absorption, mg/cm2 , Min)	-	800	-
Cl No.4.7, Table No. 5 , iii) , b)(Water Desorption, percent, Min)	-	800	-
Cl No.4.8 , Table No. 6 , i)(Abrasion resistance (Volume loss), mm3 , Max)	-	600	-
Cl No.4.8 , Table No. 6 , ii)("Flexing resistance Belt Method at 90 diameter Mandrel or Bennewart method, cut growth, Max")	-	600	-
Cl No.4.8 , Table No. 6 , iii)("Hydrolysis resistance, cut growth after 150 000 flexes, in mm, Max")	-	2500	-
Cl No.4.9 , Table No. 7 , i)(Compression set, percent, Max)	-	500	-
Cl No.4.9 , Table No. 7 , ii)(Split tear strength, kg/25 mm, Min)	-	450	-
Cl No.4.9 , Table No. 7 , iii)(Heat shrinkage, percent, Max)	-	800	-
Cl No.4.10 , Table No. 8 , i)(First dry collapsing load, hardness, N, Min)	-	800	-
Cl No.4.10 , Table No. 8 , ii)(Resilience, percent, Min)	-	800	-
Cl No.4.10 , Table No. 8 , iii)(Moisture resistance, percent, Min)	-	800	-
Cl No.4.10 , Table No. 8 , iv) , a)(Initial dry area shape retention, percent, Min)	-	800	-
Cl No.4.10 , Table No. 8 , iv) , b)(Area shape retention after 10th collapse, dry, percent, Min)	-	800	-
Cl No.4.11 , Table No. 9 , i)(Peel strength, N/mm, Min)	-	500	-
Cl No.4.11 , Table No. 9 , ii)(Shear strength, kPa , Min)	-	600	-
Cl No.4.12 , Table No. 10 , i)(Limit of useful extension, percent, Min)	-	800	-
Cl No.4.13 , Table No. 11 , i)(Breaking strength of lace, N, Min)	-	500	-
Cl No.4.13 , Table No. 11 , ii)(Lace tag strength, N, Min)	-	500	-
Cl No.4.13 , Table No. 11 , iii)(Lace to lace abrasion,)	-	800	-
Cl No.4.13 , Table No. 11 , iv)("Colour fastness to water Gray Scale Rate, Min Rating")	-	600	-
Cl No.4.13 , Table No. 11 , v)(Strength of Buckle/Ski hook, N, Min)	-	500	-
Cl No.4.13 , Table No. 11 , vi)(Corrosion resistance)	-	600	-
Cl No . 5(MARKING AND PACKING)	-	500	-
Cl No . 4.14, Table no. 1 of IS 17011(iv)(Chromium (VI))	-	800	-
Cl No . 4.14, Table no. 1 of IS 17011(x)(pH)	-	500	-
Clause 4.2 - 4.2.1(Construction)	-	200	-
Clause 4.2 - 4.2.2(Construction)	-	200	-
Clause 4.3 - 4.3.1(Whole Footwear)	-	500	-
Clause 4.3 - 4.3.2(Whole Footwear)	-	500	-
Clause 4.3 - 4.3.3(Upper to Mid Sole/Out Sole Bond Performance)	-	500	-
Clause 4.3 - 4.3.4(Upper to Composite Sole Bond Performance(Applicable Only When the Sole is Composite))	-	500	-
Clause 4.3 - 4.3.5(Out Sole to Mid Sole (Multilayer) Bond)	-	500	-
Clause 4.3 - 4.3.7(Complete Shoe Flexing)	-	640	-
Clause 4.4, Table 1 ii)(Tear strength)	-	450	-
Clause 4.4, Table 1 iv)-a(Water Vapour Permeability)	-	800	-
Clause 4.5, Table 3 v)-b(Water Vapour Coeffecient)	-	800	-
Clause 4.4, Table 1 v)(Stitch Tear Strength(Double Hole))	-	450	-
Clause 4.4, Table 2 i)(Breaking Strength)	-	450	-
Clause 4.4, Table 2 ii)(Elongation at break)	-	450	-
Clause 4.4, Table 2 iii)(Tear strength)	-	450	-
Clause 4.4, Table 2 v)-a(Water Vapour Permeability)	-	800	-
Clause 4.4, Table 2 v)-b(Water Vapour Coeffecient)	-	800	-
Clause 4.5, Table 3 i)(Tear strength)	-	450	-
Clause 4.5, Table 3 ii)(Abrasion Resistance)	-	600	-
Clause 4.5, Table 3 v)-a(Water Vapour Permeability)	-	800	-
Clause 4.6, Table 4 i)(Thickness)	-	200	-
Clause 4.6, Table 4 ii)(Abrasion Resistance)	-	600	-
Clause 4.6, Table 4 iv)-a(Water Absorption)	-	800	-
Clause 4.6, Table 4 iv)-b(Water Desorption)	-	800	-
Clause 4.8, Table 6 i)(Abrasion Resistance)	-	600	-
Clause 4.8, Table 6 ii)(Flexing Resistance)	-	600	-
Clause 4.8, Table 6 iii)(Hydrolysis Resistance)	-	2500	-
Clause 4.9, Table 7 ii)(Split Tear strength)	-	450	-
Clause 4.9, Table 7 iii)(Heat shrinkage)	-	800	-
Clause 4.4, Table 1 iv)-b(Water Vapour Coeffecient)	-	800	-
Clause 4.7, Table 5 i)(Thickness)	-	200	-
Clause 4.7, Table 5 iii)-a(Water Absorption)	-	800	-
Cl No.4.4 , Table No. 2 , i) , b)(Flexing resistance, Wet condition)	-	600	-
Clause 4.7, Table 5 ii)(Abrasion Resistance)	-	800	-
Clause 4.7, Table 5 iii)-b(Water Desorption)	-	800	-
Cl-5, Table -1 S. No-(i) (Amendment No-1)(Insole)	-	200	-
Cl-5, Table -1 S. No- (ii) (Amendment No-1)(Toe spring height)	-	200	-
Cl-5, Table -1 S. No- (iii) (Amendment No-1)("Bond performance (a) Upper to sole/mid sole/composite sole (b) Interlayer bond strength")	-	500	-
Cl-5, Table -1 S. No- (iv) (Amendment No-1)(Energy absorption at seat region)	-	800	-
Cl-5, Table -1 S. No- (v) (Amendment No-1)(Complete shoe flexing)	-	640	-
Cl-5, Table -1 S. No-(vi) (Amendment No-1)(Washability)	-	800	-
Cl-5, Table -1 S. No- (vii) (Amendment No-1)(Slip resistance, coefficient of friction (COF),)	-	1500	-
Cl-5, Table -1 S. No- (viii) (Amendment No-1)("Abrasion resistance a-Cellular sole b-Solid sole")	-	600	-
Cl-5, Table -1 S. No- (xi) (Amendment No-1)(Hydrolysis resistance)	-	2500	-
Cl-6, Table -2 S. No- (i) (Amendment No-1)(Tear strength)	-	450	-
Cl-6, Table -2 S. No- (ii) (Amendment No-1)("Colour fastness rubbing a-Dry: (rubbing) b-Wet: (rubbing)")	-	500	-
Cl-6, Table -2 S. No- (iii), a) (Amendment No-1)(Water vapour permeability)	-	800	-
Cl-6, Table -2 S. No- (iii), b) (Amendment No-1)(Water vapour coefficient)	-	800	-
Cl-6, Table -2 S. No- (iv),(Amendment No-1)(Stitch tear strength)	-	450	-
Cl-6, Table -3 S. No- (i),(Amendment No-1)(Breaking strength, N/mm, Min)	-	500	-
Cl-6, Table -3 S. No- (ii),(Amendment No-1)("Elongation at break a-Tighter direction b-Stretch direction")	-	450	-
Cl-6, Table -3 S. No- (iii),(Amendment No-1)("Tear strength, N, Min a) For fabric b) For all other materials")	-	450	-
Cl-6, Table -3 S. No- (iv),(Amendment No-1)("Flexing resistance a- Dry condition b-Wet condition")	-	600	-
Cl-6, Table -3 S. No- (v), a (Amendment No-1)(Water vapour permeability)	-	800	-
Cl-6, Table -3 S. No- (v), b (Amendment No-1)(Water vapour coefficient)	-	800	-
Cl-6, Table -3 S. No- (vi), (Amendment No-1)(Hydrolysis resistance)	-	2500	-
Cl-6, Table -3 S. No- (vii), (Amendment No-1)(Bursting strength)	-	800	-
Cl-6, Table -4 S. No- (ii),(Amendment No-1)("Abrasion resistance, cycles a- Dry condition b-Wet condition")	-	600	-
Cl-6, Table -4 S. No- (iii),(Amendment No-1)(Colour fastness to rubbing , grey scale rate with 10 rubs on dry or wet, Min)	-	500	-
Cl-6, Table -4 S. No- (iv),(Amendment No-1)(Colour fastness to perspiration)	-	800	-
Cl-6, Table -4 S. No- (v), a (Amendment No-1)(Water vapour permeability)	-	800	-
Cl-6, Table -4 S. No- (v), b (Amendment No-1)(Water vapour coefficient)	-	800	-
Cl-6, Table -5 S. No- (i), (Amendment No-1)(Thickness, mm, Min)	-	200	-
Cl-6, Table -5 S. No-(ii), (Amendment No-1)(Flexing index, Min)	-	640	-
Cl-6, Table -5 S. No-(iii), (Amendment No-1)(Abrasion resistance,)	-	600	-
Cl-6, Table -5 S. No- (iv), a (Amendment No-1)(Water absorption)	-	800	-
Cl-6, Table -5 S. No- (iv), b (Amendment No-1)(Water desorption, percent)	-	800	-
Cl-6, Table -6 S. No- (i), (Amendment No-1)(Thickness, mm, Min)	-	200	-
Cl-6, Table -6 S. No- (ii), (Amendment No-1)("Abrasion resistance, cycles a- Dry condition b-Wet condition")	-	600	-
Cl-6, Table -6 S. No- (iii),a (Amendment No-1)(Water absorption)	-	800	-
Cl-6, Table -6 S. No- (iv), b (Amendment No-1)(Water desorption, percent)	-	800	-
Cl-6, Table -7 S. No- (i), (Amendment No-1)(Flexing resistance (Belt method or Bennewart method))	-	600	-
Cl-6, Table -7 S. No- (ii), (Amendment No-1)(Hydrolysis resistance, cut growth after flexes)	-	2500	-
Cl-6, Table -8 S. No- (i), (Amendment No-1)("Compression set, percent, Max a) For EVA b) For all other materials")	-	500	-
Cl-6, Table -8 S. No- (ii), (Amendment No-1)(Split tear strength)	-	450	-
Cl-6, Table -8 S. No- (iii), (Amendment No-1)(Heat shrinkage)	-	800	-
Cl-6, Table -9 S. No- (i), (Amendment No-1)(First dry collapsing load, hardness)	-	800	-
Cl-6, Table -9 S. No- (ii), (Amendment No-1)(Resilience, percent)	-	800	-
Cl-6, Table -9 S. No- (iii), (Amendment No-1)(Moisture resistance)	-	800	-
Cl-6, Table -9 S. No- (iv), a (Amendment No-1)(Initial dry area shape retention)	-	800	-
Cl-6, Table -9 S. No- (iv), b (Amendment No-1)(Area shape retention after 10th collapse)	-	800	-
Cl-6, Table -10 S. No- (i), (Amendment No-1)("Peel strength a) Initial b) After 5 000 wear cycles")	-	500	-
Cl-6, Table -10 S. No- (ii), (Amendment No-1)("Shear strength a) Initial b) After 5 000 wear cycles")	-	500	-
Cl-6, Table -11 S. No- (i), (Amendment No-1)(Limit of useful extension)	-	800	-
Cl-6, Table -12 S. No- (i), (Amendment No-1)(Breaking strength of lace)	-	500	-
Cl-6, Table -12 S. No- (ii), (Amendment No-1)(Lace tag strength)	-	500	-
Cl-6, Table -12 S. No- (iii), (Amendment No-1)(Lace to lace abrasion)	-	800	-
Cl-6, Table -12 S. No- (iv), (Amendment No-1)(Colour fastness to water (for lace) (contact method))	-	500	-
Cl-6, Table -12 S. No- (iv), (Amendment No-1)(Colour fastness to water (for lace) (contact method))	-	500	-
Cl-6, Table -12 S. No (v), (Amendment No-1)(Strength of buckle/ski hook)	-	500	-
Cl-6, Table -12 S. No- (vi), (Amendment No-1)(Corrosion resistance)	-	600	-
Cl-6, Table -4 S. No- (i),(Amendment No-1)(Tear strength, N, Min)	-	450	-
Cl No.4.1(Sampling and Conditioning)	-	500	-
Cl No.4.2(Construction)	-	300	-
Cl No.4.3(Whole Footwear)	-	300	-
4.3.1(Insole)	-	300	-
4.3.2(Toe spring height)	-	500	-
Cl No.4.4 , Table No. 2 , i)(Breaking strength, N/mm, Min)	-	500	-
Cl No.4.4 , Table No. 2 , vii)(Bursting Strength, kg/cm2 , Min)	-	500	-
Cl No.4.7, Table No. 5 , ii)(Abrasion resistance, cycles)	-	600	-
Cl No.4.10 , Table No. 8 , ii)(Resilience, percent, Min)	-	500	-
Cl No.4.11 , Table No. 9 , ii)(Shear strength, kPa , Min)	-	800	-
Cl No.4.13 , Table No. 11 , iv)("Colour fastness to water Gray Scale Rate, Min Rating")	-	500	-
Cl No . 5(MARKING AND PACKING)	-	600	-
Clause 4.2 - 4.2.1(Construction)	-	500	-
Clause 4.2 - 4.2.2(Construction)	-	500	-
Clause 4.3 - 4.3.1(Whole Footwear)	-	600	-
Clause 4.3 - 4.3.2(Whole Footwear)	-	600	-
Clause 4.4, Table 2 i)(Breaking Strength)	-	500	-
Clause 4.9, Table 7 iii)(Heat shrinkage)	-	2000	-
Clause 4.7, Table 5 ii)(Abrasion Resistance)	-	600	-
Cl-5, Table -1 S. No-(i) (Amendment No-1)(Insole)	-	500	-
Cl-5, Table -1 S. No- (ii) (Amendment No-1)(Toe spring height)	-	500	-
Cl-5, Table -1 S. No- (iii) (Amendment No-1)("Bond performance (a) Upper to sole/mid sole/composite sole (b) Interlayer bond strength")	-	500	-
Cl-5, Table -1 S. No- (iv) (Amendment No-1)(Energy absorption at seat region)	-	800	-
Cl-5, Table -1 S. No- (v) (Amendment No-1)(Complete shoe flexing)	-	600	-
Cl-5, Table -1 S. No- (vii) (Amendment No-1)(Slip resistance, coefficient of friction (COF),)	-	1500	-
Cl-5, Table -1 S. No- (viii) (Amendment No-1)("Abrasion resistance a-Cellular sole b-Solid sole")	-	600	-
Cl-5, Table -1 S. No- (xi) (Amendment No-1)(Hydrolysis resistance)	-	2500	-
Cl-6, Table -2 S. No- (i) (Amendment No-1)(Tear strength)	-	450	-
Cl-6, Table -2 S. No- (ii) (Amendment No-1)("Colour fastness rubbing a-Dry: (rubbing) b-Wet: (rubbing)")	-	500	-
Cl-6, Table -2 S. No- (iii), a) (Amendment No-1)(Water vapour permeability)	-	800	-
Cl-6, Table -2 S. No- (iii), b) (Amendment No-1)(Water vapour coefficient)	-	800	-
Cl-6, Table -2 S. No- (iv),(Amendment No-1)(Stitch tear strength)	-	450	-
Cl-6, Table -3 S. No- (i),(Amendment No-1)(Breaking strength, N/mm, Min)	-	500	-
Cl-6, Table -3 S. No- (ii),(Amendment No-1)("Elongation at break a-Tighter direction b-Stretch direction")	-	450	-
Cl-6, Table -3 S. No- (iii),(Amendment No-1)("Tear strength, N, Min a) For fabric b) For all other materials")	-	450	-
Cl-6, Table -3 S. No- (iv),(Amendment No-1)("Flexing resistance a- Dry condition b-Wet condition")	-	600	-
Cl-6, Table -3 S. No- (v), a (Amendment No-1)(Water vapour permeability)	-	800	-
Cl-6, Table -3 S. No- (v), b (Amendment No-1)(Water vapour coefficient)	-	800	-
Cl-6, Table -3 S. No- (vi), (Amendment No-1)(Hydrolysis resistance)	-	2500	-
Cl-6, Table -3 S. No- (vii), (Amendment No-1)(Bursting strength)	-	600	-
Cl-6, Table -4 S. No- (ii),(Amendment No-1)("Abrasion resistance, cycles a- Dry condition b-Wet condition")	-	600	-
Cl-6, Table -4 S. No- (iii),(Amendment No-1)(Colour fastness to rubbing , grey scale rate with 10 rubs on dry or wet, Min)	-	500	-
Cl-6, Table -4 S. No- (iv),(Amendment No-1)(Colour fastness to perspiration)	-	600	-
Cl-6, Table -4 S. No- (v), a (Amendment No-1)(Water vapour permeability)	-	800	-
Cl-6, Table -4 S. No- (v), b (Amendment No-1)(Water vapour coefficient)	-	800	-
Cl-6, Table -5 S. No- (i), (Amendment No-1)(Thickness, mm, Min)	-	200	-
Cl-6, Table -5 S. No-(ii), (Amendment No-1)(Flexing index, Min)	-	600	-
Cl-6, Table -5 S. No-(iii), (Amendment No-1)(Abrasion resistance,)	-	600	-
Cl-6, Table -5 S. No- (iv), a (Amendment No-1)(Water absorption)	-	800	-
Cl-6, Table -5 S. No- (iv), b (Amendment No-1)(Water desorption, percent)	-	800	-
Cl-6, Table -6 S. No- (i), (Amendment No-1)(Thickness, mm, Min)	-	200	-
Cl-6, Table -6 S. No- (ii), (Amendment No-1)("Abrasion resistance, cycles a- Dry condition b-Wet condition")	-	600	-
Cl-6, Table -6 S. No- (iii),a (Amendment No-1)(Water absorption)	-	800	-
Cl-6, Table -6 S. No- (iv), b (Amendment No-1)(Water desorption, percent)	-	800	-
Cl-6, Table -7 S. No- (i), (Amendment No-1)(Flexing resistance (Belt method or Bennewart method))	-	600	-
Cl-6, Table -7 S. No- (ii), (Amendment No-1)(Hydrolysis resistance, cut growth after flexes)	-	2500	-
Cl-6, Table -8 S. No- (i), (Amendment No-1)("Compression set, percent, Max a) For EVA b) For all other materials")	-	500	-
Cl-6, Table -8 S. No- (ii), (Amendment No-1)(Split tear strength)	-	450	-
Cl-6, Table -8 S. No- (iii), (Amendment No-1)(Heat shrinkage)	-	800	-
Cl-6, Table -9 S. No- (i), (Amendment No-1)(First dry collapsing load, hardness)	-	800	-
Cl-6, Table -9 S. No- (ii), (Amendment No-1)(Resilience, percent)	-	800	-
Cl-6, Table -9 S. No- (iii), (Amendment No-1)(Moisture resistance)	-	800	-
Cl-6, Table -9 S. No- (iv), a (Amendment No-1)(Initial dry area shape retention)	-	800	-
Cl-6, Table -9 S. No- (iv), b (Amendment No-1)(Area shape retention after 10th collapse)	-	800	-
Cl-6, Table -10 S. No- (i), (Amendment No-1)("Peel strength a) Initial b) After 5 000 wear cycles")	-	500	-
Cl-6, Table -10 S. No- (ii), (Amendment No-1)("Shear strength a) Initial b) After 5 000 wear cycles")	-	800	-
Cl-6, Table -11 S. No- (i), (Amendment No-1)(Limit of useful extension)	-	800	-
Cl-6, Table -12 S. No- (i), (Amendment No-1)(Breaking strength of lace)	-	500	-
Cl-6, Table -12 S. No- (ii), (Amendment No-1)(Lace tag strength)	-	500	-
Cl-6, Table -12 S. No- (iii), (Amendment No-1)(Lace to lace abrasion)	-	600	-
Cl-6, Table -12 S. No (v), (Amendment No-1)(Strength of buckle/ski hook)	-	500	-
Cl-6, Table -12 S. No- (vi), (Amendment No-1)(Corrosion resistance)	-	800	-
Cl-6, Table -4 S. No- (i),(Amendment No-1)(Tear strength, N, Min)	-	450	-
Cl-6, Table -12 S. No- (iv), (Amendment No-1)(Colour fastness to water (for lace) (contact method))	-	600	-
Cl-6, Table -12 S. No- (iv), (Amendment No-1)(Colour fastness to water (for lace) (contact method))	-	600	-
Cl No.4.3(Whole Footwear)	-	640	-
Cl No.4.4 , Table No. 2 , v)(Stitch tear strength (double hole), N/mm, Min)	-	600	-
Cl No.4.5 , Table No. 3 , iv)("Colour fastness to perspiration (contact method) Grey scale rate, Min")	-	600	-
Cl No.4.6 , Table No. 4 , iii)(Abrasion resistance, at 400 cycles)	-	500	-
Cl No.4.9 , Table No. 7 , iii)(Heat shrinkage, percent, Max)	-	1200	-
Cl No.4.10 , Table No. 8 , ii)(Resilience, percent, Min)	-	400	-
Cl No.4.10 , Table No. 8 , iii)(Moisture resistance, percent, Min)	-	600	-
Cl No.4.12 , Table No. 10 , i)(Limit of useful extension, percent, Min)	-	600	-
Cl No.4.13 , Table No. 11 , i)(Breaking strength of lace, N, Min)	-	450	-
Cl No.4.13 , Table No. 11 , iii)(Lace to lace abrasion,)	-	600	-
Cl No . 5(MARKING AND PACKING)	-	200	-
Clause 4.3 - 4.3.1(Whole Footwear)	-	640	-
Clause 4.3 - 4.3.2(Whole Footwear)	-	640	-
Clause 4.4, Table 1 v)(Stitch Tear Strength(Double Hole))	-	600	-
Clause 4.9, Table 7 iii)(Heat shrinkage)	-	1200	-
Cl No.4.4 , Table No. 2 , i) , b)(Flexing resistance, Wet condition)	-	800	-
Cl-5, Table -1 S. No-(i) (Amendment No-1)(Insole)	-	200	-
Cl-5, Table -1 S. No- (ii) (Amendment No-1)(Toe spring height)	-	200	-
Cl-5, Table -1 S. No- (v) (Amendment No-1)(Complete shoe flexing)	-	640	-
Cl-6, Table -2 S. No- (iv),(Amendment No-1)(Stitch tear strength)	-	600	-
Cl-6, Table -4 S. No- (iii),(Amendment No-1)(Colour fastness to rubbing , grey scale rate with 10 rubs on dry or wet, Min)	-	600	-
Cl-6, Table -8 S. No- (iii), (Amendment No-1)(Heat shrinkage)	-	1200	-
Cl-6, Table -10 S. No- (ii), (Amendment No-1)("Shear strength a) Initial b) After 5 000 wear cycles")	-	600	-
Cl-6, Table -12 S. No- (i), (Amendment No-1)(Breaking strength of lace)	-	450	-
Cl-6, Table -12 S. No- (vi), (Amendment No-1)(Corrosion resistance)	-	600	-
Cl-6, Table -12 S. No- (iv), (Amendment No-1)(Colour fastness to water (for lace) (contact method))	-	500	-
Cl-6, Table -12 S. No- (iv), (Amendment No-1)(Colour fastness to water (for lace) (contact method))	-	500	-

Complete

02 Sep, 2027

-
Exclusion: Table-1 (vi), Table-1 (ix), Table-2 (v) & Table-1 (x)- Chemical Requirement, Table 1 xii Lead

493

DELHI TEST HOUSE, Azadhpur

IS 737 (2024)

WROUGHT ALUMINIUM AND ALUMINIUM ALLOY SHEET AND STRIP FOR GENERAL ENGINEERING PURPOSES SPECIFICATION (Fifth Revision)

ALL

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 7(Chemical Composition - IS 504/ IS 504 (Part-1 to 12)/ IS 504 (Part-13 to 16)/ ASTM E 1251/ IS 11035)	-	7000	NA
Cl. 7(Si - IS 504 (Part-1)/ ASTM E 1251/ IS 11035)	-	500	NA
Cl. 7(Fe - IS 504 (Part-2)/ ASTM E 1251/ IS 11035)	-	500	NA
Cl. 7(Cu - IS 504 (Part-3)/ ASTM E 1251/ IS 11035)	-	500	NA
Cl. 7(Mn - IS 504 (Part-5)/ ASTM E 1251/ IS 11035)	-	500	NA
Cl. 7(Mg - IS 504 (Part-6)/ ASTM E 1251/ IS 11035)	-	500	NA
Cl. 7(Cr - IS 504 (Part-8)/ ASTM E 1251/ IS 11035)	-	500	NA
Cl. 7(Zn - IS 504 (Part-4)/ ASTM E 1251/ IS 11035)	-	500	NA
Cl. 7(Ti - IS 504 (Part-11)/ ASTM E 1251/ IS 11035)	-	500	NA
Cl. 7(Others (Each) - IS 504/ IS 504 (Part-1 to 12)/ IS 504 (Part-13 to 16)/ ASTM E 1251/ IS 11035)	-	5000	NA
Cl. 7(Others (Total) - IS 504/ IS 504 (Part-1 to 12)/ IS 504 (Part-13 to 16)/ ASTM E 1251/ IS 11035)	-	500	NA
Cl. 8(Mechanical Properties - IS 1608 (Part-1))	-	5000	NA
Cl. 8.1(0.2% Proof Stress - IS 1608 (Part-1))	-	2000	NA
Cl. 8.1(Tensile Strength - IS 1608 (Part-1))	-	2000	NA
Cl. 8.1(Elongation on 50mm Gauge Length - IS 1608 (Part-1))	-	1000	NA
Cl. 8.2(Bend Test - IS 1599)	-	1000	NA
Cl. 10(Dimensions and Tolerances - IS 737/ IS 2676)	-	1000	NA
Cl. 13.1(Marking - IS 737)	-	250	NA
Cl. 7(Al - IS 504)	-	500	NA
Cl. 4(Ordering Information - IS 737)	-	0	NA
Cl. 4 (a)(Grade/ Thickness - IS 737)	-	0	NA
Cl. 4 (b)(Condition - IS 737)	-	0	NA
Cl. 4 (c)(Quantity in Kg - IS 737)	-	0	NA
Cl. 4 (d)(Size - Thickness X Width X Length (T X W X L) in mm for sheets and (T X W) in mm for Strips/ Coils - IS 737)	-	0	NA
Cl. 4 (e)(Coil ID and Coil Weight for Strips/ Coils - IS 737)	-	0	NA
Cl. 4 (f)(Core/ Spool Requirement for Coils - IS 737)	-	0	NA
Cl. 4 (g)(Packing Mode - IS 737)	-	0	NA
Cl. 5(Supply for Material - IS 737/ IS 10259)	-	0	NA
Cl. 9(Condition - IS 737/ IS 5052)	-	0	NA
Cl. 11(Selection of Test Samples - IS 737)	-	0	NA
Cl. 11.1(Sheet and Strip of Aluminium or Non - Heat Treatable Aluminium Alloy - IS 737)	-	0	NA
Cl. 11.2(Sheet and Strip of Heat - Treatable Aluminium Alloys - IS 737)	-	0	NA
Cl. 12(Retests - IS 737/ IS 10259)	-	0	NA
Cl. 13(Packaging - IS 737/ IS 10259)	-	0	NA
Cl. 6(Freedom from Defects - IS 737)	-	250	NA

Complete

-
Included w.e.f.12.03.2025

494

The Synthetic and Art Silk Mills' Research Association

IS 16513 (2016)

Agro textiles “ Insect nets for agriculture and horticulture purposes “ Specification

18500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6/6.1( REQUIREMENTS Dimensions and Mass a) Length)	-	400	-
6/6.1( REQUIREMENTS Dimensions and Mass b) width)	-	400	-
6/6.1( REQUIREMENTS Dimensions and Mass c) Mass gm/m2)	-	400	-
4.2( Netting Fabric)	-	200	-
4/4.1(b) percent on avarage value; and( MATERIAL / HDPE Monofilament Yarn)	-	400	-
4/4.1(a) percent on individual value; and( MATERIAL / HDPE Monofilament Yarn)	-	400	-
4.2( Netting Fabric)	-	200	-
4.2( Netting Fabric)	-	200	-
5.0(types a) Type I — having mesh of 30; b) Type II — having mesh of 40; andc) c) Type III — having mesh of 50)	-	2100	-
4/4.1.1/60°C / 95°C( MATERIAL / HDPE Monofilament Yarn)	-	1000	-
4.3( Colour)	-	0	-
6.2(Table-1)	-	12300	-
6.2/3(cover factor)	-	500	-

Complete

14 Dec, 2023

14 Dec, 2026

-
-

495

Unique Test House

IS 9295 (2024)

STEEL TUBES FOR IDLERS FOR BELT CONVEYORS - SPECIFICATION (second revision)

ALL GRADE TYPE DESIGNATION AND SIZE

7200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
As per Clause 5(Types /Grade and Designation)	-	500	-
As per clause 6(Material)	-	100	-
As per clause 7(Manufacture)	-	200	-
As per clause 7.1.5(Sulphur)	-	800	-
As per clause 7.1.6(Phosphorus)	-	800	-
As per clause 8(Mechanical Properties)	-	200	-
As per clause 8.1(Tensile Test)	-	700	-
As per clause 8.1.1(Yield Stress)	-	700	-
As per clause 8.1.2(Elongation)	-	700	-
As per clause 8.2(Drift Expansion Test)	-	1000	-
As per clause 8.3(Flattening Test)	-	1500	-
As per clause 9(Weight)	-	700	-
As per clause 10(Hardness Test)	-	1000	-
As per clause 11(Mechanical Test)	-	1500	-
As per clause 12(Retests)	-	1500	-
As per clause 13(Dimension Tolerance)	-	500	-
As per clause 14(Workmanship)	-	200	-
As per clause 15(Straightness)	-	800	-
As per clause 16(Length)	-	200	-
As per clause 17(Surface Protection)	-	500	-
As per clause 18(Marking)	-	500	-

Complete

07 Sep, 2025

-
-

496

SIIR, Delhi Shriram Institute For Industrial Research

IS 16415 (2015)

Composite cement - Specification

Composite Cement

26000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Chemical Requirements)	-	0	-
7(Physical Requirement)	-	0	-
6 -Table - 2 i(Insoluble residue - Cl 4.10 of IS 4032:1985)	-	1000	30% Discount
6 -Table - 2 ii(Magnesia - Cl 4.8 of IS 4032:1985)	-	2000	30% Discount
6 -Table - 2 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-	1000	30% Discount
6 -Table - 2 iv(Sulphide sulphur (S) - Cl 6.12 of IS 4032:1985)	-	1000	30% Discount
6 -Table - 2 v(Loss on ignition - Cl 4.2 of IS 4032:1985)	-	1000	30% Discount
6 -Table - 2 vi(Chloride content - Cl 4.13 of IS 4032:1985)	-	1000	30% Discount
Cl. 6.1,Table 2(Alkali content)	-	2000	30% Discount
6 -Table - 2 i(Insoluble residue - Cl 4.10 of IS 4032:1985)	-	0	-
6 -Table - 2 ii(Magnesia - Cl 4.8 of IS 4032:1985)	-	0	-
6 -Table - 2 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-	0	-
6 -Table - 2 iv(Sulphide sulphur (S) - Cl 6.12 of IS 4032:1985)	-	0	-
6 -Table - 2 v(Loss on ignition - Cl 4.2 of IS 4032:1985)	-	0	-
6 -Table - 2 vi(Chloride content - Cl 4.13 of IS 4032:1985)	-	0	-
Cl. 6.1,Table 2(Chloride content)	-	0	-
Cl. 6.1,Table 2(Loss on ignition)	-	0	-
Cl. 6.1,Table 2(Suilphide sulphur)	-	0	-
Cl. 6.1,Table 2(Total sulphur content calculated as sulphuric anhydride)	-	0	-
Cl. 6.1,Table 2(Magnesia)	-	0	-
Cl. 6.1,Table 2(Insoluble residue)	-	0	-
7 and Table 3 i(Fineness IS 4031(Part 2))	-	1000	30% Discount
7 and Table 3 ii a(Soundness, Le-Chate1ier expansion IS 4031(Part 3) )	-	1000	30% Discount
7 and Table 3 ii b(Soundness, Autoclave expansion IS 4031(Part 3) )	-	1000	30% Discount
7 and Table 3 iii a(Setting Time ( by Vicat Apparatus), Initial IS 4031(Part 5))	-	500	30% Discount
7 and Table 3 iii b(Setting Time ( by Vicat Apparatus ), Final IS 4031(Part 5))	-	500	30% Discount
7 and Table 3 iv a(Compretsive Strenqth .72 ± 1 hr IS 4031(Part 6))	-	5000	30% Discount
7 and Table 3 iv b(Compretsive Strenqth 168 ± 2 hr IS 4031(Part 6))	-	0	-
7 and Table 3 iv c(Compretsive Strenqth 672 ± 4 hr IS 4031(Part 6))	-	0	-
7 and Table 3 v(Drying shrinkage IS 4031(Part 10))	-	3000	30% Discount
7 and Table 3 vi(Transverse strength (optional) IS 4031(Part 8) )	-	5000	30% Discount
7 and Table 3 i(Fineness IS 4031(Part 2))	-	0	-
7 and Table 3 ii a(Soundness, Le-Chate1ier expansion IS 4031(Part 3) )	-	0	-
7 and Table 3 ii b(Soundness, Autoclave expansion IS 4031(Part 3) )	-	0	-
7 and Table 3 iii a(Setting Time ( by Vicat Apparatus), Initial IS 4031(Part 5))	-	0	-
7 and Table 3 iii b(Setting Time ( by Vicat Apparatus ), Final IS 4031(Part 5))	-	0	-
7 and Table 3 iv a(Compretsive Strenqth .72 ± 1 hr IS 4031(Part 6))	-	0	-
7 and Table 3 iv b(Compretsive Strenqth 168 ± 2 hr IS 4031(Part 6))	-	0	-
7 and Table 3 iv c(Compretsive Strenqth 672 ± 4 hr IS 4031(Part 6))	-	0	-
7 and Table 3 v(Drying shrinkage IS 4031(Part 10))	-	0	-
7 and Table 3 vi(Transverse strength (optional) IS 4031(Part 8) )	-	0	-
6(Chemical Requirements)	-	0	-
7(Physical Requirement)	-	0	-
Cl. 6.1,Table 2(Alkali content)	-	0	-
Cl. 6.1,Table 2(Chloride content)	-	0	-
Cl. 6.1,Table 2(Loss on ignition)	-	0	-
Cl. 6.1,Table 2(Suilphide sulphur)	-	0	-
Cl. 6.1,Table 2(Total sulphur content calculated as sulphuric anhydride)	-	0	-
Cl. 6.1,Table 2(Magnesia)	-	0	-
Cl. 6.1,Table 2(Insoluble residue)	-	0	-

Complete

31 Dec, 2026

-
Included w.e.f.12.03.2025

497

INDIAN TESTING LABORATORY

IS 1285 (2023)

WROUGHT ALUMINIUM AND ALUMINIUM ALLOYS EXTRUDED ROUND TUBE AND HOLLOW SECTIONS FOR GENERAL ENGINEERINGPURPOSES SPECIFICATION

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1("The extruded round tube and hollow sections shall be sound and visually free from harmful defects. ")	-	500	-
6.2(Slight discoloration due to heat treatment, minor polishing marks and spiral marks due to roll straightening shall not be a cause for rejection.)	-	500	-
8("Dimensions and tolerances of the material shall be as laid down in the Indian Standards indicated below: a) Extruded round tube IS 2673; and b) Extruded hollow sections IS 6477.")	-	1000	-
9(" Extruded round tubes and hollow sections shall be made from alloys specified in IS 733. 9.2 The chemical analysis of the material shall be carried out either in accordance with the methods specified in IS 504 (Part 1 to 12) and IS 504 (Part 13 to 16) or by any other established instrumental/chemical method. In case of any dispute the method specified in relevant parts of IS 504 shall be used as referee method. However, when the method is not given in IS 504, the referee method shall be as agreed to between the purchaser and the manufacturer. ")	-	500	-
10(Tensile test)	-	1000	-
Cl.9.1(Aluminium- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Copper- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Magnesium- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Silicon- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Iron- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Manganese- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Zinc- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Titanium and/ or other grain refining elements- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Chromium- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Remarks (Ti+V) - IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Remarks (Cr+Mn) - IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Remarks (Total Impurities)- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-

Complete

15 Aug, 2028

-
Included w.e.f 12.03.2025

498

Conformity Testing Labs Pvt. Ltd. Unit 2

IS 13450 : Part 2 : Sec 37 (2019)

Medical electrical equipment: Part 2 particular requirements for the basic safety and essential performance: Sec 37 ultrasonic medical diagnostic and monitoring equipment

950000 View breakup
-

Clause No.	Exclusion	Remark
201.4(General requirements)	-	-
201.5(General requirements for testing ME EQUIPMENT)	-	-
201.6(Classification of ME EQUIPMENT and ME SYSTEMS)	-	-
201.7(ME EQUIPMENT identification, marking and documents)	-	-
201.8(Protection against electrical HAZARDS from ME EQUIPMENT)	-	-
201.9(Protection against MECHANICAL HAZARDS OF ME EQUIPMENT and ME SYSTEMS)	-	-
201.1(Protection against unwanted and excessive radiation HAZARDS)	-	-
201.11(Protection against excessive temperatures and other HAZARDS)	-	-
201.12(Accuracy of controls and instruments and protection against hazardous outputs)	-	-
201.13(HAZARDOUS SITUATIONS and fault conditions for ME EQUIPMENT)	-	-
201.14(PROGRAMMABLE ELECTRICAL MEDICAL SYSTEMS (PEMS))	-	-
201.15(Construction of ME EQUIPMENT)	-	-
201.16(ME SYSTEMS)	-	-
201.17(ELECTROMAGNETIC COMPATIBILITY of ME EQUIPMENT and ME SYSTEMS)	-	-
202.6(ELECTROMAGNETIC COMPATIBILITY – Requirements and test)	-	-

Complete

05 Apr, 2027

-
Included w.e.f 25.03.2025 Exclusion: Cl 201.17 (Electromagnetic compatibility of ME EQUIPMENT and ME SYSTEMS)(Radiated emission, Conducted & Radiated susceptibility), Cl 202.6 (Electromagnetic disturbances – Requirements and tests)(Radiated emission, Conducted & Radiated susceptibility)

499

Alpha Test House Services LLP

IS 14862 (2000)

Fibre cement flat sheets - specification

Fibre cement flat sheets (Type-A ,Type-B)

28000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(CLASSIFICATION)	-	28000	For other Test Rs 28,000 For optional test extra- Freeze Thaw test-Rs,30000 Warm Water-Rs,10000 Heat-Rain test-Rs,15000
4.2(CLASSIFICATION -The sheets are further classified into five categories)	-	28000	For other Test Rs 28,000 For optional test extra- Freeze Thaw test-Rs,30000 Warm Water-Rs,10000 Heat-Rain test-Rs,15000
5.1.1(Nominal Length )	-	28000	For other Test -Rs 28,000 For optional test extra- Freeze Thaw test-Rs,30000 Warm Water-Rs,10000 Heat-Rain test-Rs,15000
5.1.1(Nominal Width)	-	28000	For other Test Rs 28,000 For optional test extra- Freeze Thaw test-Rs,30000 Warm Water-Rs,10000 Heat-Rain test-Rs,15000
5.1.2(Thickness)	-	28000	For other Test Rs 28,000 For optional test extra- Freeze Thaw test-Rs,30000 Warm Water-Rs,10000 Heat-Rain test-Rs,15000
5.1.4.1(Straightness of edges - Length )	-	28000	For other Test Rs 28,000 For optional test extra- Freeze Thaw test-Rs,30000 Warm Water-Rs,10000 Heat-Rain test-Rs,15000
5.1.4.1(Straightness of edges - Width )	-	28000	For other Test Rs 28,000 For optional test extra- Freeze Thaw test-Rs,30000 Warm Water-Rs,10000 Heat-Rain test-Rs,15000
5.1.4.2(Squareness of edges)	-	28000	For other Test Rs 28,000 For optional test extra- Freeze Thaw test-Rs,30000 Warm Water-Rs,10000 Heat-Rain test-Rs,15000
5.2.1(Bending Strength)	-	28000	For other Test Rs 28,000 For optional test extra- Freeze Thaw test-Rs,30000 Warm Water-Rs,10000 Heat-Rain test-Rs,15000
5.2.2(Apparent Density)	-	28000	For other Test Rs 28,000 For optional test extra- Freeze Thaw test-Rs,30000 Warm Water-Rs,10000 Heat-Rain test-Rs,15000
6.1(For TypeA sheets - Bending Strength)	-	28000	For other Test Rs 28,000 For optional test extra- Freeze Thaw test-Rs,30000 Warm Water-Rs,10000 Heat-Rain test-Rs,15000
6.2(For TypeA sheets - Water Impermeability)	-	28000	For other Test Rs 28,000 For optional test extra- Freeze Thaw test-Rs,30000 Warm Water-Rs,10000 Heat-Rain test-Rs,15000
6.3(For TypeA sheets - Frost Resistance)	-	28000	For other Test Rs 28,000 For optional test extra- Freeze Thaw test-Rs,30000 Warm Water-Rs,10000 Heat-Rain test-Rs,15000
6.4(For TypeA sheets - Warm Water)	-	28000	For other Test Rs 28,000 For optional test extra- Freeze Thaw test-Rs,30000 Warm Water-Rs,10000 Heat-Rain test-Rs,15000
6.5(For TypeA sheets - Soak-Dry)	-	28000	For other Test Rs 28,000 For optional test extra- Freeze Thaw test-Rs,30000 Warm Water-Rs,10000 Heat-Rain test-Rs,15000
6.6( Heat-Rain)	-	28000	For other Test Rs 28,000 For optional test extra- Freeze Thaw test-Rs,30000 Warm Water-Rs,10000 Heat-Rain test-Rs,15000

Complete

31 Dec, 2026

-
-

500

Hi Physix Laboratory India Private Limited

IS 302 : Part 2 : Sec 8 (2024)

Household and Similar Electrical Appliances âSafety Part 2 Particular Requirements Section 8 Shavers, Hair Clippers and Similar Appliances (First Revision)

73000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking and instructions)	-	2000	-
8(Protection against access to live parts)	-	2000	-
10(Power input and current)	-	2000	-
11(Heating)	-	4000	-
12(Charging of metal-ion batteries)	-	15000	-
13.1 &13.2(Leakage current test)	-	1500	-
13.1 &13.3(Electric strength test)	-	1500	-
14(Transient overvoltages)	-	2000	-
15(Moisture resistance)	-	2000	-
15.3(Moisture resistance)	-	2000	-
16.1 &16.2(Leakage current test)	-	1500	-
16.1 & 16.3(Electric strength test)	-	1500	-
17(Overload protection of transformers and associated circuits)	-	4000	-
19.1 to 19.13, Table No. - 9(Abnormal operation)	-	5000	Charges applicable excluding the test of Cl.19.11.4.1 to Cl.19.11.4.7. The testing charges for EMI/EMC Testing (Cl.19.11.4.1 to Cl.19.11.4.7) will be charged extra.
19.101(Abnormal operation)	-	0	Testing charges included in Cl.19.1 TO cL.19.13
20.1(Stability and mechanical hazards)	-	1000	-
20.2(Stability and mechanical hazards)	-	1000	-
21(Mechanical strength)	-	3000	-
21.101(Mechanical strength)	-	0	Testing charges included in Cl.21
21.102(Mechanical strength)	-	0	Testing charges included in Cl.21
21.103(Mechanical strength)	-	0	Testing charges included in Cl.21
22(Construction)	-	5000	-
22.101(Construction)	-	0	Testing charges included in Cl.22
22.102(Construction)	-	0	Testing charges included in Cl.22
22.103(Construction)	-	0	Testing charges included in Cl.22
23(Internal wiring)	-	2000	-
24(Components)	-	3000	-
25("Supply connection and external flexible cords")	-	1000	-
26("Terminals for external conductors")	-	1000	-
27(Provision for earthing)	-	2000	-
28(Screws and connections)	-	1000	-
29("Clearances, creepage distances and solid insulation")	-	2000	-
30(Resistance to heat and fire)	-	3000	-
31(Resistance to rusting)	-	1000	-
32("Radiation, toxicity and similar hazards")	-	1000	-

Complete

20 Jun, 2028

-
Included w.e.f 25.03.2025 Exclusion : Cl 24 (Components), Cl 32 ("Radiation, toxicity and similar hazards")

501

DELHI TEST HOUSE, Azadhpur

IS 736 (1986)

Specification for wrought aluminium and aluminium alloy plate for general engineering purposes (Third Revision)

ALL

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Freedom from defect)	-	500	-
5(chemical composition)	-	4500	-
6.1 table 2(0.2% proof strength)	-	1700	-
6.1 table 2(tensile strength)	-	1700	-
6.1 table 2(Elongation)	-	1700	-
8(Dimensions & Tolerances)	-	2000	-
5.1, Table 1(Aluminium)	-	500	-
5.1, Table 1(Copper)	-	500	-
5.1, Table 1(Magnesium)	-	500	-
5.1, Table 1(Silicon)	-	500	-
5.1, Table 1(Iron)	-	500	-
5.1, Table 1(Mangnese)	-	500	-
5.1, Table 1(Zinc)	-	500	-
5.1, Table 1(Titanium and /or other grain refining element)	-	500	-
5.1, Table 1(Chromium)	-	500	-
5.1, Table 1(Vanadium)	-	500	-

Complete

-
Included w.e.f. 03.03.2025

502

IDMA LABORATORIES LIMITED

IS 5405 (2025)

Disposable Sanitary Napkin/Panty Liner/Maternity Pad/Period Panty - Specification ( Third Revision )

Sanitary Napkin, Panty liner, Maternity Pad, Period panty

261600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Cover/Top sheet)	-	800	Testing charges are Rs. 800/- for Cl. no. 3.1 Cover / Top sheet, 3.2 Absorbent core & 3.3 Barrier or Bottom sheet.
3.2(Absorbent core)	-	0	Testing charges already mentioned above at cl. no. 3.1 Cover / Top sheet i.e. Rs. 800/-.
3.3(Barrier or bottom sheet)	-	0	Testing charges already mentioned above at cl. no. 3.1 Cover / Top sheet i.e. Rs. 800/-.
4.1(Types)	-	800	Testing charges are 800/- for cl. 4.1 & 4.2
4.2(shapes)	-	0	Testing charges are 800/- for cl. 4.1 & 4.2 already mentioned above.
5(Sizes)	-	800	Testing charges are 800/- for Size, Size class, Length (Absorbent core only, Width (Absorbent core only as per cl. 5 Table - 1.
Cl. 5 Table-1(Type)	-	0	Total testing charges are Rs. 2,61,600/- including Bio compatibility evaluation - Cytotoxicity, Irritation & Skin sensitization (as per cl. no. 7.4) & (excluding Compostability as per cl. 7.6).
Cl. 5 Table-1(Size class)	-	0	Testing charges are 800/- for Size, Size class, Length (Absorbent core only, Width (Absorbent core only as per cl. 5 Table - 1 already mentioned above.
Cl. 5 Table-1(Length (Absorbent core only))	-	0	Testing charges are 800/- for Size, Size class, Length (Absorbent core only, Width (Absorbent core only as per cl. 5 Table - 1 already mentioned above.
Cl. 5 Table-1(Width (Absorbent core only))	-	0	Testing charges are 800/- for Size, Size class, Length (Absorbent core only, Width (Absorbent core only as per cl. 5 Table - 1 already mentioned above.
6.1(Manufacture, workmanship and finish)	-	500	Testing charges are 500/- for cl. 6.1 & 6.2.
6.2(Manufacture, workmanship and finish)	-	0	Testing charges are 500/- for cl. 6.1 & 6.2 already mentioned above.
7.1(pH value (IS 1390))	-	1000	Testing charges are Rs. 21,600/- excluding Bio compatibility evaluation - Cytotoxicity, Irritation & Skin sensitization (as per cl. no. 7.4) &excluding Compostability as per cl. 7.6).
7.2(Ability to withstand Pressure after absorption)	-	1200	Testing charges are 1200/- for cl. Ability to Withstand Pressure after Absorption & Ability to Withstand Pressure after Absorption - leakage.
7.2(Ability to withstand Pressure after absorption - Leakage)	-	0	Testing charges are 1200/- for cl. Ability to Withstand Pressure after Absorption & Ability to Withstand Pressure after Absorption - leakage already mentioned above.
7.3.1(Total Viable count)	-	3000	-
7.3.2(Staphylococcus aureus)	-	3000	-
7.4(Biocompatibility evaluation - Cytotoxicity (IS/ISO 10993 P-5))	-	50000	-
7.4(Biocompatibility evaluation - Irritation (IS 17932 P-7))	-	70000	-
7.4(Biocompatibility evaluation - skin Sensitization (Optional) (IS 17932 P-6))	-	120000	-
7.5(Phthalate test)	-	8000	-
7.7(Anti bacterial activity value (Optional) (IS/ISO 20743))	-	2500	-
7.6(Compostability (Optional) (IS/ISO 17088))	-	0	Clause no. 7.6 Compostability (Optional) test is applied for Exclusion as the test facilities are currently not available.

Complete

31 Dec, 2026

-
Included w.e.f.05.03.2025 Exclusion Cl 7.6 (Compostability (Optional) (IS/ISO 17088)

503

IDMA LABORATORIES LIMITED

IS 15219 (2024)

Aluminium phosphide powder formulation - Specification (first revision)

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2.1(Description - IS 15219:2002)	-	1000		-
3.3.1(Aluminium Phosphide Content - IS 6438:1980)	-	6000		-

Complete

31 Dec, 2026

-
Included w.e.f.24.04.2025

504

IDMA LABORATORIES LIMITED

IS 9356 (2024)

Butachlor emulsifiable concentrate (EC) - Specification (first revision)

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2.1(Description - IS 9356 : 2024)	-	500	-
3.2.2(Cold Test - IS 6940 : 1982)	-	1000	-
3.2.3(Flash Point - IS 6940 : 1982)	-	1000	-
3.2.4(Emulsion Test - IS 6940 : 1982)	-	1500	-
3.3.1(Butachlor Content - IS 9355 : 2024)	-	3000	-
3.3.2(Acidity (as H2SO4) - IS 6940 : 1982)	-	1500	-
3.3.2(Alkalinity (as NaOH) - IS 6940 : 1982)	-	0	Testing charges i.e. Rs. 1500/- already mentioned above at clause no. 3.3.2 (Acidity (as H2SO4).

Complete

31 Dec, 2026

-
Included w.e.f 09.04.2025

505

IDMA LABORATORIES LIMITED

IS 9355 (2024)

Butachlor, Technical - Specification (First Revision)

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Description - IS 9355 : 2024)	-	500	-
3.2 & 7, Table - 1 (i)(Butachlor Content - IS 9355 : 2024)	-	3000	-
3.2 & 7, Table - 1 (ii)(Moisture Content - IS 6940 : 1982)	-	2000	-
3.2 & 7, Table - 1 (iii)(Acidity (as H2SO4) - IS 6940 : 1982)	-	1500	-
3.2 & 7, Table - 1 (iv)(Material insoluble in Acetone - IS 6940 : 1982)	-	1500	-

Complete

31 Dec, 2026

-
Included w.e.f 09.04.2025

506

IDMA LABORATORIES LIMITED

IS 8074 (2024)

Monocrotophos, Soluble Concentrate (SL) - Specification (Third Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2.1(Description - IS 8074 : 2024)	-	500	-
3.2.2(Cold Test - IS 6940 : 1982)	-	1000	-
3.2.3(Flash Point - IS 6940 : 1982)	-	1000	-
3.3.1(Monocrotophos Content - IS 8025 : 2024)	-	3500	-
3.3.2(Free Aceto - Acetic Acid Monomethyl - Amide (MMA) content - IS 8025 : 2024)	-	3000	-
3.3.3(Acidity ( as H2SO4) - IS 6940 : 1982)	-	1000	-

Complete

31 Dec, 2026

-
Included w.e.f. 24.04.2025

507

IDMA LABORATORIES LIMITED

IS 8025 (2024)

Monocrotophos, Technical - Specification (Third Revision)

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Description - IS 8025 : 2024)	-	1000	-
3.2 & 7 Table - 1 (i)(Monocrotophos Content - IS 8025 : 2024)	-	3500	-
3.2 & 7 Table - 1 (ii)(Free Acetic Acid Mono - methylamide (MMA) - IS 8025 : 2024)	-	3000	-
3.2 & 7 Table - 1 (iii)(Acidity (as H2SO4) - IS 6940 : 1982)	-	1500	-

Complete

31 Dec, 2026

-
Included w.e.f.24.04.2025

508

IDMA LABORATORIES LIMITED

IS 3205 (2024)

Precipitated Barium Carbonate, Technical - Specification (Second Revision)

Grade 1 & Grade 2

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Description - IS 3205:2024)	-	500	-
4.2 Table(i)(Barium (as Ba) - IS 3205: 2024)	-	1500	-
4.2 Table(ii)(Carbonate (as CO3) - IS 3205: 2024)	-	2000	-
4.2 Table(iii)(Moisture - IS 3205: 2024)	-	2000	-
4.2 Table(iv)(Matter insoluble in hydrochloric acid - IS 3205: 2024)	-	1500	-
4.2 Table(v)(Free alkali - IS 3205: 2024)	-	1500	-
4.2 Table(vi)(Water soluble sulphide (as BaS) - IS 3205: 2024)	-	1500	-
4.2 Table(vii)(Total sulphur (as SO4) - IS 3205: 2024)	-	1500	-
4.2 Table(viii)(Alkali and other metal sulphates (as BaSO4) - IS 3205: 2024)	-	1500	-
4.2 Table(ix)(Sodium oxides (as Na2O)- IS 3205: 2024)	-	1500	-
4.2 Table(x)(Iron (as Fe2O3)- IS 3205: 2024)	-	1500	-
4.2 Table(xi)(Tap density- IS 3205: 2024)	-	1000	-
4.2 Table(xii)(Residue retained on 63 micron IS sieve- IS 3205: 2024)	-	1500	-
4.2 Tablexii(i)(Reaction efficiency (after 45 min)- IS 3205: 2024)	-	1000	-

Complete

31 Dec, 2026

-
Included w.e.f.24.04.2025

509

CSIR-Central Building Research Institute, Roorkee

IS 16945 (2018)

Fire resistance test for glass walls

450000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
11(Integrity, Insulation, Radiation)	-	450000		450000 plus GST for two hours

Complete

12 Mar, 2028

-
-

510

CSIR-Central Building Research Institute, Roorkee

IS 16947 (2018)

Fire resistance tests for doors with glass panes, openable glass windows and sliding glass doors

450000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
9(Integrity, Insulation, Radiation)	-	450000		450000 plus GST for two hours

Complete

12 Mar, 2028

-
-

Bureau of Indian Standards

The National Standards Body of India

Search by IS Number