BIS - LIMS (Laboratory Information Management System)

Search by IS Number

Reset

15393 Results

S.No.

Lab Name

Osl Code

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

5431

CIPET: CENTRE FOR SKILLING AND TECHNICAL SUPPORT (CSTS) - (CIPET), AURANGABAD

7123534

IS 15450 (2022)

Polyethylene-aluminium-polyethylene composite pressure pipes for hot and cold water supplies Specifications first revision of IS 15450

90150 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(MATERIALS)	-	11475	FOR 8 PARAMETERS
8(COLOUR)	-	500	-
9(DIMENSIONS OF PIPE)	-	500	-
10(VISUAL APPEARANCE)	-	500	-
11.1(Density (Method of test as per Table 3))	-	1325	700+625
11.2(Melt Flow Rate (Method of test as per Table 3))	-	1100	-
11.3(Overall Migration)	-	2200	1700+500
11.4(Thermal Stability to Oxidation (Method of test as per Table 3))	-	2200	-
11.5(Carbon Black Content and Dispersion (Method of test as per Table 3))	-	700	-
11.6(Pigment Dispersion (For Coloured Pipes) (Method of test as per Table 3))	-	0	-
11.7(Resistance to Weathering)	-	51000	36000 WEATHERING FOR 24 MONTHS AFTER WEATHERING TESTS 1800 (ELONGATION) 2200 (OIT) 11000 (HYDROSTATIC TEST FOR 1000 HOURS)
11.8(Adhesion Test)	-	1100	-
11.9(Apparent Tensile Strength of Pipe)	-	1300	-
11.11(Hydraulic Characteristics)	-	7350	850 1700 4800
14(MARKING)	-	500	-
9.3(Length of Straight Pipe)	-	500	-
11.1(Minimum Burst Pressure)	-	850	-
11.11.12(Long Term Hydrostatic Test)	-	1700	-
12.1(Type Test)	-	4800	-
5(MATERIALS)	-	0	-
8(COLOUR)	-	0	-
9(DIMENSIONS OF PIPE)	-	0	-
10(VISUAL APPEARANCE)	-	0	-
11.1(Density (Method of test as per Table 3))	-	0	-
11.2(Melt Flow Rate (Method of test as per Table 3))	-	0	-
11.3(Overall Migration)	-	0	-
11.4(Thermal Stability to Oxidation (Method of test as per Table 3))	-	0	-
11.5(Carbon Black Content and Dispersion (Method of test as per Table 3))	-	0	-
11.6(Pigment Dispersion (For Coloured Pipes) (Method of test as per Table 3))	-	0	-
11.7(Resistance to Weathering)	-	0	-
11.8(Adhesion Test)	-	0	-
11.9(Apparent Tensile Strength of Pipe)	-	0	-
11.11(Hydraulic Characteristics)	-	0	-
14(MARKING)	-	0	-
9.3(Length of Straight Pipe)	-	0	-
11.1(Minimum Burst Pressure)	-	0	-
11.11.12(Long Term Hydrostatic Test)	-	0	-
12.1(Type Test)	-	0	-

31 Dec, 2026

-
Included w.e.f.09.04.2025

5432

BUREAU VERITAS CONSUMER PRODUCTS SERVICES INDIA PRIVATE LIMITED, NOIDA

8127706

IS 302 : Part 2 : Sec 202 (1992)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 202 electric stoves

53000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Classification- IS 302-1 )	-	0	-
6(Classification- IS 302-1)	-	0	-
7.1(Marking- IS 302-1)	-	2000	-
7.1(Marking- IS 302-1)	-	0	Testing charges included in Cl. 7.1
7.1(Marking- IS 302-1)	-	0	Testing charges included in Cl. 7.1
7.1(Marking- IS 302-1)	-	0	Testing charges included in Cl. 7.1
7.1(Marking- IS 302-1)	-	0	Testing charges included in Cl. 7.1
7.1(Marking- IS 302-1)	-	0	Testing charges included in Cl. 7.1
7.1(Marking- IS 302-1)	-	0	Testing charges included in Cl. 7.1
7.1(Marking- IS 302-1)	-	0	Testing charges included in Cl. 7.1
7.1(Marking- IS 302-1)	-	0	Testing charges included in Cl. 7.1
7.3(Marking- IS 302-1)	-	0	Testing charges included in Cl. 7.1
7.4(Marking- IS 302-1)	-	0	Testing charges included in Cl. 7.1
7.6(Marking- IS 302-1)	-	0	Testing charges included in Cl. 7.1
7.11(Marking- IS 302-1)	-	0	Testing charges included in Cl. 7.1
7.12(Marking- IS 302-1)	-	0	Testing charges included in Cl. 7.1
7.13(Marking- IS 302-1)	-	0	Testing charges included in Cl. 7.1
7.14(Marking- IS 302-1)	-	0	Testing charges included in Cl. 7.1
7.15(Marking- IS 302-1)	-	0	Testing charges included in Cl. 7.1
7.101(Marking)	-	0	Testing charges included in Cl. 7.1
8( Protection Against Electric Shock, IS 302-1)	-	2000	-
10(Power Input and Current, IS 302-1)	-	2000	-
11(Heating, IS 302-1)	-	4000	-
11(Heating, IS 302-1)	-	0	Testing charges included in Cl. 11
11(Heating, IS 302-1)	-	0	Testing charges included in Cl. 11
11(Heating, IS 302-1)	-	0	Testing charges included in Cl. 11
11(Heating, IS 302-1)	-	0	Testing charges included in Cl. 11
11(Heating, IS 302-1)	-	0	Testing charges included in Cl. 11
11(Heating, IS 302-1)	-	0	Testing charges included in Cl. 11
12(Operation under overload conditions of appliances with heating elements, IS 302-2-202: 1992)	-	0	-
13(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-	3000	-
13(Electrical Insulation and Leakage Current at Operating Temperature: High Voltage, IS 302-1)	-	0	Testing charges included in Cl. 13
15.1(Moisture Resistance, IS 302-1)	-	4000	-
15.3(Moisture Resistance, IS 302-1)	-	0	Testing charges included in Cl. 15.1
16(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-	3000	-
16(Electrical Insulation and Leakage Current at Operating Temperature: High Voltage, IS 302-1)	-	0	Testing charges included in Cl. 16
19.2(Abnormal Operation, IS 302-1)	-	5000	-
19.2(Abnormal Operation, IS 302-1)	-	0	Testing charges included in Cl. 19.2
19.3(Abnormal Operation, IS 302-1)	-	0	Testing charges included in Cl. 19.2
19.3(Abnormal Operation, IS 302-1)	-	0	Testing charges included in Cl. 19.2
20.1(Stability & Mechanical Hazards, IS 302-1)	-	2000	-
21.1(Mechanical Strength, IS 302-1 & IS 302-2-202)	-	1500	-
22(Construction, IS 302-1)	-	5000	-
22.101(Construction)	-	0	Testing charges included in Cl. 22
22.102(Construction)	-	0	Testing charges included in Cl. 22
22.103(Construction)	-	0	Testing charges included in Cl. 22
22.104(Construction)	-	0	Testing charges included in Cl. 22
22.105(Construction)	-	0	Testing charges included in Cl. 22
22.105.1(Construction)	-	0	Testing charges included in Cl. 22
22.105.2(Construction)	-	0	Testing charges included in Cl. 22
22.106(Construction)	-	0	Testing charges included in Cl. 22
22.107(Construction)	-	0	Testing charges included in Cl. 22
11.107.1(Construction)	-	0	Testing charges included in Cl. 22
23.1(Internal Wiring, IS 302-1)	-	2000	-
23.2(Internal Wiring, IS 302-1)	-	0	Testing charges included in Cl. 23.1
23.8(Internal Wiring, IS 302-1)	-	0	Testing charges included in Cl. 23.1
23.9(Internal Wiring, IS 302-1)	-	0	Testing charges included in Cl. 23.1
23.10(Internal Wiring, IS 302-1)	-	0	Testing charges included in Cl. 23.1
24.1(Components, IS 302-1)	-	3000	-
24.2(Components, IS 302-1)	-	0	Testing charges included in Cl. 24.1
24.101(Components)	-	0	Testing charges included in Cl. 24.1
25.1(Supply Connection and External Flexible Cords, IS 302-1)	-	2000	-
25.4(Supply Connection and External Flexible Cords)	-	0	Testing charges included in Cl. 25.1
25.5(Supply Connection and External Flexible Cords, IS 302-1)	-	0	Testing charges included in Cl. 25.1
25.6(Supply Connection and External Flexible Cords, IS 302-1)	-	0	Testing charges included in Cl. 25.1
25.8(Supply Connection and External Flexible Cords, IS 302-1)	-	0	Testing charges included in Cl. 25.1
26.9(Supply Connection and External Flexible Cords, IS 302-1)	-	0	Testing charges included in Cl. 26
25.1(Supply Connection and External Flexible Cords, IS 302-1)	-	0	Testing charges included in Cl. 25.1
25.11(Supply Connection and External Flexible Cords, IS 302-1)	-	0	Testing charges included in Cl. 25.1
25.12(Supply Connection and External Flexible Cords, IS 302-1)	-	0	Testing charges included in Cl. 25.1
25.15(Supply Connection and External Flexible Cords, IS 302-1)	-	0	Testing charges included in Cl. 25.1
25.16(Supply Connection and External Flexible Cords, IS 302-1)	-	0	Testing charges included in Cl. 25.1
25.17(Supply Connection and External Flexible Cords, IS 302-1)	-	0	Testing charges included in Cl. 25.1
25.18(Supply Connection and External Flexible Cords, IS 302-1)	-	0	Testing charges included in Cl. 25.1
25.19(Supply Connection and External Flexible Cords, IS 302-1)	-	0	Testing charges included in Cl. 25.1
25.2(Supply Connection and External Flexible Cords, IS 302-1)	-	0	Testing charges included in Cl. 25.1
25.21(Supply Connection and External Flexible Cords, IS 302-1)	-	0	Testing charges included in Cl. 25.1
25.22(Supply Connection and External Flexible Cords, IS 302-1)	-	0	Testing charges included in Cl. 25.1
26(Terminals for External Conductors, IS 302-1)	-	1000	-
27.1(Provision for Earthing, IS 302-1)	-	2000	-
27.2(Provision for Earthing, IS 302-1)	-	0	Testing charges included in Cl. 27.1
27.3(Provision for Earthing, IS 302-1)	-	0	Testing charges included in Cl. 27.1
27.4(Provision for Earthing, IS 302-1)	-	0	Testing charges included in Cl. 27.1
27.5(Provision for Earthing, IS 302-1)	-	0	Testing charges included in Cl. 27.1
28(Screws & Connections, IS 302-1)	-	1000	-
29.1(Clearances, Creepage distances and Solid Insulation, IS 302-1)	-	2000	-
29.2(Clearances, Creepage distances and Solid Insulation, IS 302-1)	-	0	Testing charges included in Cl. 29.1
30.1(Resistance to Heat, Fire & Tracking, IS 302-1)	-	1000	-
30.2(Resistance to Heat, Fire & Tracking, IS 302-1)	-	2000	-
31(Resistance of Rusting, IS 302-1)	-	0	-

-
Included w.e.f.20.06.2025 Exclusion (EMI/EMC)Cl 19.11.4.1 TO Cl 19.11.4.7

5433

MARQUIS TECHNOLOGIES PRIVATE LIMITED, NOIDA

8175126

IS 10322 : Part 5 : Sec 5 (2013)

Luminaires: Part 5 particular requirements: Sec 5 floodlights (First Revision)

45000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(General Test Requireements)	-	4000	-
5(Classification of Luminaires')	-	4000	-
6.0(Marking)	-	4000	-
7.0(Construction)	-	6000	-
8.0(Creepage Distance and Clearances)	-	4000	-
9.0(Provision for earthing)	-	4000	-
10.0(Terminals)	-	3000	-
11.0(External & Internal Wiring)	-	4000	-
12.0(Protection against electric shock)	-	4000	-
13.0(Endurance Tests and Thermal Tests)	-	8000	-
14.0(Resistance to Dust & Moisture)	-	3000	-
15.0(Insulation Resistance and Electric Strength)	-	3000	-
16.0(Resistance to Heat , fire and tracking)	-	6000	-
17.0(Photometric Test)	-	8000	-

13 Dec, 2026

-
Included w.e.f 19.05.2025

5434

KPML Low Voltage Rotating Machine and Hydraulic Laboratory Karad Projects and motors Limited

7187626

IS 9079 (2018)

Monoset pumps for clear, cold water for agricultural and water supply purposes - Specification (Third Revision)

Monoset Pump for Agricultural Purpose(0.37KW to 25KW)

24467 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1(DIRECTION OF ROTATION (Cl 7))	-	5000	-
7.2(DIRECTION OF ROTATION (Cl 7))	-	5000	-
9.1(DESIGN FEATURES (Cl 9))	-	5000	-
9.2(DESIGN FEATURES (Cl 9))	-	5000	-
13.1(Guarantee and tolerances on Pump Performance (Cl 13))	-	5000	-
13.2(Guarantee and tolerances on Pump Performance (Cl 13))	-	5000	-
9.1(DESIGN FEATURES (Cl 9))	-	5000	-
9.2(DESIGN FEATURES (Cl 9))	-	5000	-
13.1(Guarantee and tolerances on Pump Performance (Cl 13))	-	5000	-
13.2(Guarantee and tolerances on Pump Performance (Cl 13))	-	5000	-
7(Contructional Features)	-	10000	-
7.1(Material of Construction)	-	10000	-
7.2(Gaskets.Seals and packings)	-	5000	-
9(Design Features)	-	10000	-
9.1.1(The pump may be equipped with replaceable bearing and wearing ring, wherever provided.)	-	5000	-
9.1.2(The pump shall be capable to perform as per guaranteed duty point at the manometric suction lift as specified in Table 1.)	-	5000	-
9.3(The manufacturer shall have a system of controlling dimensional accuracy within a scheme of fits and tolerance limits. The system shall help interchangeability and fitment at site for replacement spares during subsequent repair and maintenance.)	-	5000	-
9.4(The pump efficiency of monoset pumps at duty point as declared by the manufacturer for 2 and 4 poles shall not be less than given in Fig. 3 to Fig. 6 and beyond this range, the efficiency shall be declared by manufacturer.)	-	15000	-
10.6.2, 10.6.3(Direction of Rotation)	-	5000	-
11.8(Type test)	-	24467	-
11.8.1(a)(Measurement of stator resistance)	-	5000	-
11.8.1(b)(High Voltage test)	-	5000	-
11.8.1(c)(Insulation Resistance test)	-	5000	-
11.8.1(d)(No load test at rated voltage)	-	5000	-
11.8.1(e)(Locked rotor)	-	5000	-
11.8.1(f)(Breakaway (starting) torque)	-	5000	-
11.8.1(g)(Reduced voltage running up test at no load)	-	5000	-
11.8.1(h)(Temperature rise test at rated voltage)	-	24467	-
11.8.1(j)(Temperature rise test at reduced voltage)	-	24467	-
13.1.1(The pumpset shall be guaranteed for their performance of the nominal volume rate of flow and the nominal head at the guaranteed duty point. The overall efficiency of the pumpset shall be guaranteed at the declared duty point only.)	-	24467	-
13.1.2(The guarantee shall be deemed to have been met with, if the measured values of head, volume rate of flow and overall efficiency are within the limits indicated in clause 8 of IS 11346. However, after applying the tolerance, overall efficiency value shall not be less than that derived from Fig. 3 to 6.)	-	24467	-
13.1.3(Monoset motor shall not get overloaded in the specified operating head range at rated voltage and supply frequency.)	-	24467	-
13.1.4(The tolerance shall apply to guaranteed duty point only.)	-	5000	-
15.1(Marking)	-	5000	-
15.1(Marking)	-	5000	-
15.1(Marking)	-	5000	-
15.1(Marking)	-	5000	-
15.1(Marking)	-	5000	-
15.1(Marking)	-	5000	-
15.1(Marking)	-	5000	-
15.1(Marking)	-	5000	-
15.1(Marking)	-	5000	-
15.1(Marking)	-	5000	-
15.1(Marking)	-	5000	-
15.1(Marking)	-	5000	-
15.1(Marking)	-	5000	-
15.1(Marking)	-	5000	-
15.1(Marking)	-	5000	-
15.1(Marking)	-	5000	-
15.1(Marking)	-	5000	-
15.1(Marking)	-	5000	-
15.1(Hydrostatic Pressure Test)	-	5000	-
13.5(Minimum Current Requirement)	-	5000	-
13(Guarantee and tolerance on pump performance)	-	5000	-
13.4.1 (Amendment-1)(Pump Efficiency)	-	5000	-
8.2 IS 11346 : 2002(Verification of Guarantee Rate of flow and head (Cl.8.2 IS 11346 : 2002))	-	5000	-
12.5(Efficiency)	-	24467	-
Cl.8.3 b IS 11346 : 2002(Overall efficiency)	-	24467	-
13.1.1 (8.2 of IS 11346 : 2002)(Verification of Guarantee Rate of flow and head (Cl.8.2 IS 11346 : 2002))	-	24467	-
13.1.1 (8.2 of IS 11346 : 2002)(Verification of Guarantee Rate of flow and head (Cl.8.2 IS 11346 : 2002))	-	24467	-
12.5(Efficiency)	-	24467	-
Cl.8.3 b IS 11346 : 2002(Overall efficiency)	-	24467	-
Cl13.2.3 IS 9079:2002(Current consumption)	-	24467	-
12.2(Laboratory Test)	-	24467	-
Cl13.2.3 IS 9079:2002(Current consumption)	-	24467	-
8.2 IS 11346 : 2002(Verification of Guarantee Rate of flow and head (Cl.8.2 IS 11346 : 2002))	-	24467	-
10.1(GENERAL REQUIREMENTS Casing)	-	1000	-
10.2(GENERAL REQUIREMENTS Impeller)	-	1000	-
10.3(GENERAL REQUIREMENTS Shaft)	-	1000	-
10(General Requirements)	-	1000	-
10.1(General Requirements(Casing))	-	1000	-
10.2(General Requirements(Impeller))	-	1000	-
10.3(General Requirements(Shaft))	-	1000	-
10.5(Provision of Earthing)	-	1000	-
10.6.1(Terminal Marking)	-	1000	-
8.6.5(If four core cable is used, the fourth core is to be used for earthing.)	-	1000	-
11.1.1(Type of Enclosures)	-	25000	-

26 Aug, 2028

-
Exclusion: Cl 10.4.1, Cl 10.4.2, Cl 10.4.3, v10.4.4 (General Requirements(Balancing))

5435

Customer Services & Development Center, HPCL-Mittal Energy Limited, Noida

8171106

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

Polyethylene Pipes for water supply - Specification

55000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.10(Slow Crack Growth Rate)	-	5500	-
8.9 table-6(Elongation at Break)	-	2000	-
8.8(Tensile Strength for Butt-fusion)	-	2000	-
8.7(Density)	-	750	-
8.5 (Oxidation Induction Time)	-	3000	-
8.4( Melt Flow Rate)	-	1200	-
8.2(Longitudinal Reversion Test)	-	1100	-
8.1.2 table -5(Internal Pressure Creep Rupture Test of Pipe Joints)	-	1600	-
8,/8.1/8.1.1 table-5(PERFORMANCE REQUIREMENTS / Hydraulic Characteristics/ Internal Pressure Creep Rupture Test of Pipe)	-	22000	-
7.4.1.2(Ovality)	-	0	Already Covered in Dimensions
Cl-7.4(Mean Outside Diameter (For upto 50 mm take 8 reading, above 50mm take 6 reading & average will be reported))	-	500	-
7.2(Length)	-	500	-
6.2.1(6.1.1 Identification Stripes)	-	0	Already covered in 6.2 Colour
6.2(Colour)	-	500	-
6.1.4(PIPE DESCRIPTION)	-	0	Already Covered in 6.1
6.1.3 (PIPE DESCRIPTION)	-	0	Already Covered in 6.1
6, 6.1.2(PIPE DESCRIPTION)	-	0	Already Covered in 6.1
6, 6.1.1(PIPE DESCRIPTION)	-	0	Already Covered in 6.1
6, 6.1(PIPE DESCRIPTION)	-	500	-
8.6(Overall migration)	-	8000	-
8.3(Carbon black)	-	2000	Already Covered
5.4(Anti oxydent)	-	3000	-
5.3(d)(Carbon Black Master Batch)	-	1000	-
5.2(Polyethylene Resin)	-	8500	Already Covered in 5.2 T2
5.2(Density)	-	1500	Already Covered in 5.2 T2
5.2(MFI @ 1900C/5.0 Kg)	-	1500	Already Covered in 5.2 T2
5.2(Volatile matter Content)	-	1000	Already Covered in 5.2 T2
Clause 7.1(Visual Apperance)	-	500	-
Clause 8.3(Carbon Black Dispersion)	-	1000	Already Covered
8.9,T6("Tensile - IS 4984-2016 (Annexure-H)")	-	2000	Already Covered
8.9,T6("Elongation -IS 4984-2016 (Annexure-H)")	-	2000	Already Covered
Cl 8.3(Carbon Black Dispersion)	-	1000	Already Covered
5.3 (a)(Carbon Black Master Batch)	-	0	Already Covered
8.7(Density-IS 7328:2020)	-	1500	-
8.7(Corrected Density- IS 7328:2020)	-	1500	Already Covered
5.2,T2(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	1500	-
Table-2 (iii, iv)(Thermal Stability (Oxidation Induction Time), Volatile Matter)	-	4000	-
7.3(Coiling)	-	500	-
Clause 8.6(Overall migration (surface of material))	-	7999.99	Already Covered
Clause 8.6(Overall migration (stimulate))	-	8000	Already Covered
Clause 7.3(Coiling)	-	500	Already Covered
5, 5.1 table-1(MATERIALS)	-	0	Already Covered
7()	-	0	Already Covered
7.1(Visual Appearance)	-	0	Already Covered
Cl. 8.3(Carbon Black Dispersion)	-	1000	Already Covered
8.10(Slow Crack Growth Rate)	-	5500	Already Covered
5.2(Density)	-	1500	Already Covered
5.2(MFI @ 1900C/5.0 Kg)	-	1500	Already Covered
5.2(Volatile matter Content)	-	1000	Already Covered
Clause 7.1(Visual Apperance)	-	500	-
Clause 8.3(Carbon Black Dispersion)	-	1000	Already Covered
8.9,T6("Tensile - IS 4984-2016 (Annexure-H)")	-	2000	Already Covered
8.9,T6("Elongation -IS 4984-2016 (Annexure-H)")	-	2000	Already Covered
Cl 8.3(Carbon Black Dispersion)	-	1000	Already Covered
8.7(Density-IS 7328:2020)	-	1500	-
8.7(Corrected Density- IS 7328:2020)	-	1500	Already Covered
5.2,T2(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	1500	-
Table-2 (iii, iv)(Thermal Stability (Oxidation Induction Time), Volatile Matter)	-	4000	-
7.3(Coiling)	-	500	Already Covered
Clause 8.6(Overall migration (surface of material))	-	8000	Already Covered
Clause 8.6(Overall migration (stimulate))	-	8000	Already Covered
Clause 7.3(Coiling)	-	500	Already Covered
7()	-	0	Already Covered
7.1(Visual Appearance)	-	499.99	Already Covered
Cl. 8.3(Carbon Black Dispersion)	-	1000	Already Covered
8.10(Slow Crack Growth Rate)	-	5500	-
5.2(Density)	-	1500	-
5.2(MFI @ 1900C/5.0 Kg)	-	1500	-
5.2(Volatile matter Content)	-	999.98	-
Clause 7.1(Visual Apperance)	-	500	ALREADY COVERED
Clause 8.3(Carbon Black Dispersion)	-	1000	-
8.9,T6("Tensile - IS 4984-2016 (Annexure-H)")	-	2000	-
8.9,T6("Elongation -IS 4984-2016 (Annexure-H)")	-	2000	-
Cl 8.3(Carbon Black Dispersion)	-	1000	-
8.7(Density-IS 7328:2020)	-	1500	-
8.7(Corrected Density- IS 7328:2020)	-	1500	-
5.2,T2(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	1500	-
Table-2 (iii, iv)(Thermal Stability (Oxidation Induction Time), Volatile Matter)	-	3999.99	-
7.3(Coiling)	-	500	-
Clause 8.6(Overall migration (surface of material))	-	8000	-
Clause 8.6(Overall migration (stimulate))	-	8000	-
Clause 7.3(Coiling)	-	500	-
7()	-	500	-
7.1(Visual Appearance)	-	500	-
Cl. 8.3(Carbon Black Dispersion)	-	1000	-
Cl 8.3(Carbon Black Content)	-	1000	-
Clause 8.3(Carbon Black content)	-	1000	-
Cl. 8.3(Carbon Black Content)	-	1000	-
5.3(c)(Carbon Black Master Batch)	-	1000	-
8.10(Slow Crack Growth Rate)	-	5500	-
5.2(Density)	-	1500	-
5.2(MFI @ 1900C/5.0 Kg)	-	1500	-
5.2(Volatile matter Content)	-	1000	-
Clause 7.1(Visual Apperance)	-	500	-
Clause 8.3(Carbon Black Dispersion)	-	1000	-
8.9,T6("Tensile - IS 4984-2016 (Annexure-H)")	-	2000	-
8.9,T6("Elongation -IS 4984-2016 (Annexure-H)")	-	2000	-
Cl 8.3(Carbon Black Dispersion)	-	1000	-
8.7(Density-IS 7328:2020)	-	1500	-
8.7(Corrected Density- IS 7328:2020)	-	1500	-
5.2,T2(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	1500	-
Table-2 (iii, iv)(Thermal Stability (Oxidation Induction Time), Volatile Matter)	-	4000	-
7.3(Coiling)	-	500	-
Clause 8.6(Overall migration (surface of material))	-	8000	-
Clause 8.6(Overall migration (stimulate))	-	8000	-
Clause 7.3(Coiling)	-	500	-
7()	-	0	-
7.1(Visual Appearance)	-	500	-
Cl. 8.3(Carbon Black Dispersion)	-	2000	-
Cl 8.3(Carbon Black Content)	-	2000	-
Clause 8.3(Carbon Black content)	-	2000	-
Cl. 8.3(Carbon Black Content)	-	2000	-
8.10(Slow Crack Growth Rate)	-	5500	-
5.2(Density)	-	1500	-
5.2(MFI @ 1900C/5.0 Kg)	-	1500	-
5.2(Volatile matter Content)	-	1000	-
Clause 7.1(Visual Apperance)	-	0	-
Clause 8.3(Carbon Black Dispersion)	-	1000	-
8.9,T6("Tensile - IS 4984-2016 (Annexure-H)")	-	2000	-
8.9,T6("Elongation -IS 4984-2016 (Annexure-H)")	-	2000	-
Cl 8.3(Carbon Black Dispersion)	-	1000	-
8.7(Density-IS 7328:2020)	-	1500	-
8.7(Corrected Density- IS 7328:2020)	-	1500	-
5.2,T2(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	1500	-
Table-2 (iii, iv)(Thermal Stability (Oxidation Induction Time), Volatile Matter)	-	4000	-
7.3(Coiling)	-	500	-
Clause 8.6(Overall migration (surface of material))	-	8000	-
Clause 8.6(Overall migration (stimulate))	-	8000	-
Clause 7.3(Coiling)	-	500	-
7()	-	0	-
7.1(Visual Appearance)	-	500	-
Cl. 8.3(Carbon Black Dispersion)	-	100	-
Cl 8.3(Carbon Black Content)	-	8000	-
Clause 8.3(Carbon Black content)	-	8000	-
Cl. 8.3(Carbon Black Content)	-	8000	-
8.10(Slow Crack Growth Rate)	-	5500	-
5.2(Density)	-	1500	-
5.2(MFI @ 1900C/5.0 Kg)	-	1500	-
5.2(Volatile matter Content)	-	1000	-
Clause 7.1(Visual Apperance)	-	500	-
Clause 8.3(Carbon Black Dispersion)	-	1000	-
8.9,T6("Tensile - IS 4984-2016 (Annexure-H)")	-	2000	-
8.9,T6("Elongation -IS 4984-2016 (Annexure-H)")	-	2000	-
Cl 8.3(Carbon Black Dispersion)	-	1000	-
8.7(Density-IS 7328:2020)	-	1500	-
8.7(Corrected Density- IS 7328:2020)	-	1500	-
5.2,T2(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	1500	-
Table-2 (iii, iv)(Thermal Stability (Oxidation Induction Time), Volatile Matter)	-	4000	-
7.3(Coiling)	-	500	-
Clause 8.6(Overall migration (surface of material))	-	8000	-
Clause 8.6(Overall migration (stimulate))	-	8000	-
Clause 7.3(Coiling)	-	500	-
7()	-	0	-
7.1(Visual Appearance)	-	0	-
Cl. 8.3(Carbon Black Dispersion)	-	1000	-
Cl 8.3(Carbon Black Content)	-	1000	-
Clause 8.3(Carbon Black content)	-	1000	-
Cl. 8.3(Carbon Black Content)	-	1000	-
8.10(Slow Crack Growth Rate)	-	5500	-
5.2(Density)	-	1500	-
5.2(MFI @ 1900C/5.0 Kg)	-	1500	-
5.2(Volatile matter Content)	-	999.99	-
Clause 7.1(Visual Apperance)	-	500	-
Clause 8.3(Carbon Black Dispersion)	-	1000	-
8.9,T6("Tensile - IS 4984-2016 (Annexure-H)")	-	2000	-
8.9,T6("Elongation -IS 4984-2016 (Annexure-H)")	-	2000	-
Cl 8.3(Carbon Black Dispersion)	-	1000	-
8.7(Density-IS 7328:2020)	-	1500	-
8.7(Corrected Density- IS 7328:2020)	-	1500	-
5.2,T2(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	1500	-
Table-2 (iii, iv)(Thermal Stability (Oxidation Induction Time), Volatile Matter)	-	4000	-
7.3(Coiling)	-	500	-
Clause 8.6(Overall migration (surface of material))	-	8000	-
Clause 8.6(Overall migration (stimulate))	-	8000	-
Clause 7.3(Coiling)	-	500	-
7()	-	0	-
7.1(Visual Appearance)	-	500	-
Cl. 8.3(Carbon Black Dispersion)	-	1000	-
Cl 8.3(Carbon Black Content)	-	2000	-
Clause 8.3(Carbon Black content)	-	2000	-
Cl. 8.3(Carbon Black Content)	-	2000	-
8.10(Slow Crack Growth Rate)	-	5500	-
5.2(Density)	-	1500	-
5.2(MFI @ 1900C/5.0 Kg)	-	1500	-
5.2(Volatile matter Content)	-	1000	-
Clause 7.1(Visual Apperance)	-	500	-
Clause 8.3(Carbon Black Dispersion)	-	1000	-
8.9,T6("Tensile - IS 4984-2016 (Annexure-H)")	-	2000	-
8.9,T6("Elongation -IS 4984-2016 (Annexure-H)")	-	2000	-
Cl 8.3(Carbon Black Dispersion)	-	1000	-
8.7(Density-IS 7328:2020)	-	1500	-
8.7(Corrected Density- IS 7328:2020)	-	1500	-
5.2,T2(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	1500	-
Table-2 (iii, iv)(Thermal Stability (Oxidation Induction Time), Volatile Matter)	-	4000	-
7.3(Coiling)	-	500	-
Clause 8.6(Overall migration (surface of material))	-	8000	-
Clause 8.6(Overall migration (stimulate))	-	8000	-
Clause 7.3(Coiling)	-	500	-
7()	-	0	-
7.1(Visual Appearance)	-	500	-
Cl. 8.3(Carbon Black Dispersion)	-	1000	-
Cl 8.3(Carbon Black Content)	-	2000	-
Clause 8.3(Carbon Black content)	-	2000	-
Cl. 8.3(Carbon Black Content)	-	2000	-
8.10(Slow Crack Growth Rate)	-	5500	-
5.2(Density)	-	1500	-
5.2(MFI @ 1900C/5.0 Kg)	-	1500	-
5.2(Volatile matter Content)	-	1000	-
Clause 7.1(Visual Apperance)	-	500	-
Clause 8.3(Carbon Black Dispersion)	-	1000	-
8.9,T6("Tensile - IS 4984-2016 (Annexure-H)")	-	2000	-
8.9,T6("Elongation -IS 4984-2016 (Annexure-H)")	-	2000	-
Cl 8.3(Carbon Black Dispersion)	-	1000	-
8.7(Density-IS 7328:2020)	-	1500	-
8.7(Corrected Density- IS 7328:2020)	-	1500	-
5.2,T2(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	1500	-
Table-2 (iii, iv)(Thermal Stability (Oxidation Induction Time), Volatile Matter)	-	4000	-
7.3(Coiling)	-	500	-
Clause 8.6(Overall migration (surface of material))	-	8000	-
Clause 8.6(Overall migration (stimulate))	-	8000	-
Clause 7.3(Coiling)	-	500	-
7()	-	0	-
7.1(Visual Appearance)	-	500	-
Cl. 8.3(Carbon Black Dispersion)	-	1000	-
Cl 8.3(Carbon Black Content)	-	2000	-
Clause 8.3(Carbon Black content)	-	2000	-
Cl. 8.3(Carbon Black Content)	-	2000	-
8.10(Slow Crack Growth Rate)	-	5500	-
5.2(Density)	-	1500	-
5.2(MFI @ 1900C/5.0 Kg)	-	1500	-
5.2(Volatile matter Content)	-	1000	-
Clause 7.1(Visual Apperance)	-	500	-
Clause 8.3(Carbon Black Dispersion)	-	1000	-
8.9,T6("Tensile - IS 4984-2016 (Annexure-H)")	-	2000	-
8.9,T6("Elongation -IS 4984-2016 (Annexure-H)")	-	2000	-
Cl 8.3(Carbon Black Dispersion)	-	1000	-
8.7(Density-IS 7328:2020)	-	1500	-
8.7(Corrected Density- IS 7328:2020)	-	1500	-
5.2,T2(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	1500	-
Table-2 (iii, iv)(Thermal Stability (Oxidation Induction Time), Volatile Matter)	-	4000	-
7.3(Coiling)	-	500	-
Clause 8.6(Overall migration (surface of material))	-	8000	-
Clause 8.6(Overall migration (stimulate))	-	8000	-
Clause 7.3(Coiling)	-	500	-
7()	-	0	-
7.1(Visual Appearance)	-	500	-
Cl. 8.3(Carbon Black Dispersion)	-	1000	-
Cl 8.3(Carbon Black Content)	-	2000	-
Clause 8.3(Carbon Black content)	-	2000	-
Cl. 8.3(Carbon Black Content)	-	2000	-
8.10(Slow Crack Growth Rate)	-	-	-
5.2(Density)	-	-	-
5.2(MFI @ 1900C/5.0 Kg)	-	-	-
5.2(Volatile matter Content)	-	-	-
Clause 7.1(Visual Apperance)	-	-	-
Clause 8.3(Carbon Black Dispersion)	-	-	-
8.9,T6("Tensile - IS 4984-2016 (Annexure-H)")	-	-	-
8.9,T6("Elongation -IS 4984-2016 (Annexure-H)")	-	-	-
Cl 8.3(Carbon Black Dispersion)	-	-	-
8.7(Density-IS 7328:2020)	-	-	-
8.7(Corrected Density- IS 7328:2020)	-	-	-
5.2,T2(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	-	-
Table-2 (iii, iv)(Thermal Stability (Oxidation Induction Time), Volatile Matter)	-	-	-
7.3(Coiling)	-	-	-
Clause 8.6(Overall migration (surface of material))	-	-	-
Clause 8.6(Overall migration (stimulate))	-	-	-
Clause 7.3(Coiling)	-	-	-
7()	-	-	-
7.1(Visual Appearance)	-	-	-
Cl. 8.3(Carbon Black Dispersion)	-	-	-
Cl 8.3(Carbon Black Content)	-	-	-
Clause 8.3(Carbon Black content)	-	-	-
Cl. 8.3(Carbon Black Content)	-	-	-

28 Jul, 2028

-
Included w.e.f.04.08.2025 Exclusion "5.3(e) (Carbon Black Master Batch) 5.3(b) (Carbon Black Master Batch) 5.3 (Toluene Extract)"

5436

Bharat Test House Pvt. Ltd. 1668 Sonipat

9168306

IS 17875 (2022)

Stainless Steel seamless pipes and tubes for general service

All Ferritic steels , Martensitic steels , Austenitic steels, Duplex

22000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.0 (Table No.- 1)(Chemical Composition,% - IS 228)	-	8000	-
10.1 (Table No.- 4)(Tensile Test,Mpa - IS 1608)	-	2000	-
11(Transverse Tension Test,%)	-	2500	-
12 (Table No.- 5)(Hardness Test,HRC,HRB&BHN- IS 1500 (Part 1) or IS 1586 (Part 1))	-	1500	-
13 (Table No.- 7)(Flaring Test)	-	1000	-
14(Flattaning Test-IS 2328)	-	1000	-
15.1 (Table No.- 8)(Grain Size,No.-IS 4748)	-	2000	-
17(Leak Tighteness Test)	-	1000	-
18("Corrosion Test-IS 10461 (Part 1) or IS 10461 (Part 2)")	-	1000	-
19(Eddy current test & Air under water)	-	1000	-
21(Workmanship, Finish and Appearance)	-	500	-
22(Repair by Welding or Grinding)	-	500	-
23 (Table No.- 9,10&11)(Dimensions and Tolerances,mm)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Carbon)	-	1000	-
"Clause 8.1 and 8.2 - Table 1"(Silicon)	-	800	-
"Clause 8.1 and 8.2 - Table 1"(Mangnese)	-	800	-
"Clause 8.1 and 8.2 - Table 1"(Nickel)	-	800	-
"Clause 8.1 and 8.2 - Table 1"(Chromium)	-	800	-
"Clause 8.1 and 8.2 - Table 1"(Molybdenum)	-	800	-
"Clause 8.1 and 8.2 - Table 1"(Sulphur)	-	800	-
"Clause 8.1 and 8.2 - Table 1"(Phosphorous)	-	800	-
"Clause 8.1 and 8.2 - Table 1"(Nitrogen)	-	800	-
"Clause 8.1 and 8.2 - Table 1"(Copper)	-	800	-
"Clause 8.1 and 8.2 - Table 1"(Aluminium)	-	800	-
"Clause 8.1 and 8.2 - Table 1"(Titanium)	-	800	-
"Clause 8.1 and 8.2 - Table 1"(Niobium)	-	800	-
"Clause 18 IS 10461(Part 1)"(Corrosion Test)	-	800	-
Clause 10.1 - Table 4(Tensile Strength)	-	2000	-
Clause 10.1 - Table 4(Percent Elongation)	-	2000	-
Clause 11(Transverse Tension Test)	-	2500	-
Clause 12(Hardness Test)	-	1500	-
Clause 13(Flaring Test)	-	1000	-
Clause 14(Flattening Test)	-	1000	-
Clause 15(Grain Size)	-	2000	-
Clause 17(Leak Tightness Test)	-	1000	-
"Clause 18 IS 10461(Part 2)"(Corrosion Test)	-	1000	-
Clause 21(Workmanship, Finish & Appearance)	-	500	-
Clause 23 Annexure A, Table 9 Table 10(Dimensions & Tolerances)	-	500	-
10.2(Hardness test IS 1500 (part-1):2019)	-	1500	-
12.2(Flaring test IS 17878:2022)	-	1000	-
16(Sampling)	-	0	-
24(Marking)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(W)	-	800	-
"Clause 8.1 and 8.2 - Table 1"(Ta)	-	800	-
"Clause 8.1 and 8.2 - Table 2"(V)	-	800	-
8.0 (Table No.- 1)(Chemical Composition,% - IS 228)	-	0	-
10.1 (Table No.- 4)(Tensile Test,Mpa - IS 1608)	-	0	-
11(Transverse Tension Test,%)	-	0	-
12 (Table No.- 5)(Hardness Test,HRC,HRB&BHN- IS 1500 (Part 1) or IS 1586 (Part 1))	-	0	-
13 (Table No.- 7)(Flaring Test)	-	0	-
14(Flattaning Test-IS 2328)	-	0	-
15.1 (Table No.- 8)(Grain Size,No.-IS 4748)	-	0	-
17(Leak Tighteness Test)	-	0	-
18("Corrosion Test-IS 10461 (Part 1) or IS 10461 (Part 2)")	-	0	-
19(Eddy current test & Air under water)	-	0	-
21(Workmanship, Finish and Appearance)	-	0	-
22(Repair by Welding or Grinding)	-	0	-
23 (Table No.- 9,10&11)(Dimensions and Tolerances,mm)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Carbon)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Silicon)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Mangnese)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Nickel)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Chromium)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Molybdenum)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Sulphur)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Phosphorous)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Nitrogen)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Copper)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Aluminium)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Titanium)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Niobium)	-	0	-
"Clause 18 IS 10461(Part 1)"(Corrosion Test)	-	0	-
Clause 10.1 - Table 4(Tensile Strength)	-	0	-
Clause 10.1 - Table 4(Percent Elongation)	-	0	-
Clause 11(Transverse Tension Test)	-	0	-
Clause 12(Hardness Test)	-	0	-
Clause 13(Flaring Test)	-	0	-
Clause 14(Flattening Test)	-	0	-
Clause 15(Grain Size)	-	0	-
Clause 17(Leak Tightness Test)	-	0	-
"Clause 18 IS 10461(Part 2)"(Corrosion Test)	-	0	-
Clause 21(Workmanship, Finish & Appearance)	-	0	-
Clause 23 Annexure A, Table 9 Table 10(Dimensions & Tolerances)	-	0	-
10.2(Hardness test IS 1500 (part-1):2019)	-	0	-
12.2(Flaring test IS 17878:2022)	-	0	-
16(Sampling)	-	0	-
24(Marking)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(W)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Ta)	-	0	-
"Clause 8.1 and 8.2 - Table 2"(V)	-	0	-
8.0 (Table No.- 1)(Chemical Composition,% - IS 228)	-	0	-
10.1 (Table No.- 4)(Tensile Test,Mpa - IS 1608)	-	0	-
11(Transverse Tension Test,%)	-	0	-
12 (Table No.- 5)(Hardness Test,HRC,HRB&BHN- IS 1500 (Part 1) or IS 1586 (Part 1))	-	0	-
13 (Table No.- 7)(Flaring Test)	-	0	-
14(Flattaning Test-IS 2328)	-	0	-
15.1 (Table No.- 8)(Grain Size,No.-IS 4748)	-	0	-
17(Leak Tighteness Test)	-	0	-
18("Corrosion Test-IS 10461 (Part 1) or IS 10461 (Part 2)")	-	0	-
19(Eddy current test & Air under water)	-	0	-
21(Workmanship, Finish and Appearance)	-	0	-
22(Repair by Welding or Grinding)	-	0	-
23 (Table No.- 9,10&11)(Dimensions and Tolerances,mm)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Carbon)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Silicon)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Mangnese)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Nickel)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Chromium)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Molybdenum)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Sulphur)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Phosphorous)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Nitrogen)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Copper)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Aluminium)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Titanium)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Niobium)	-	0	-
"Clause 18 IS 10461(Part 1)"(Corrosion Test)	-	0	-
Clause 10.1 - Table 4(Tensile Strength)	-	0	-
Clause 10.1 - Table 4(Percent Elongation)	-	0	-
Clause 11(Transverse Tension Test)	-	0	-
Clause 12(Hardness Test)	-	0	-
Clause 13(Flaring Test)	-	0	-
Clause 14(Flattening Test)	-	0	-
Clause 15(Grain Size)	-	0	-
Clause 17(Leak Tightness Test)	-	0	-
"Clause 18 IS 10461(Part 2)"(Corrosion Test)	-	0	-
Clause 21(Workmanship, Finish & Appearance)	-	0	-
Clause 23 Annexure A, Table 9 Table 10(Dimensions & Tolerances)	-	0	-
10.2(Hardness test IS 1500 (part-1):2019)	-	0	-
12.2(Flaring test IS 17878:2022)	-	0	-
16(Sampling)	-	0	-
24(Marking)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(W)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Ta)	-	0	-
"Clause 8.1 and 8.2 - Table 2"(V)	-	0	-

-
Included w.e.f.11.07.2025

5437

BUREAU VERITAS CONSUMER PRODUCTS SERVICES INDIA PRIVATE LIMITED, NOIDA

8127706

IS 302 : Part 2 : Sec 201 (2008)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 201 electric immersion water heaters (First Revision)

57000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.6 of IS 302-‐2-‐201:2008(Classification)	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	2000	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Test charges included in Cl.7
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Test charges included in Cl.7
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Test charges included in Cl.7
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Test charges included in Cl.7
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Test charges included in Cl.7
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Test charges included in Cl.7
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Test charges included in Cl.7
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Test charges included in Cl.7
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Test charges included in Cl.7
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Test charges included in Cl.7
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Test charges included in Cl.7
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Test charges included in Cl.7
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Test charges included in Cl.7
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Test charges included in Cl.7
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Test charges included in Cl.7
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Test charges included in Cl.7
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Test charges included in Cl.7
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Test charges included in Cl.7
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Test charges included in Cl.7
Cl.8 of IS 302‐2-201: 2008(Protection Against Access to Live Parts)	-	2000	-
Cl.10 of IS 302‐2‐201:2008(Power Input and Current )	-	2000	-
Cl.11 of IS 302-2201: 2008(Heating)	-	4000	-
Cl.11 of IS 302-2201: 2008(Heating)	-	0	Test charges included in Cl.11
Cl.11 of IS 302-2201: 2008(Heating)	-	0	Test charges included in Cl.11
Cl.11 of IS 302-2201: 2008(Heating)	-	0	Test charges included in Cl.11
Cl.11 of IS 302-2201: 2008(Heating)	-	0	Test charges included in Cl.11
Cl.11 of IS 302-2201: 2008(Heating)	-	0	Test charges included in Cl.11
Cl.11 of IS 302-2201: 2008(Heating)	-	0	Test charges included in Cl.11
Cl.11 of IS 302-2201: 2008(Heating)	-	0	Test charges included in Cl.11
Cl.11 of IS 302-2201: 2008(Heating)	-	0	Test charges included in Cl.11
Cl.11 of IS 302-2201: 2008(Heating)	-	0	Test charges included in Cl.11
Cl.11 of IS 302-2201: 2008(Heating)	-	0	Test charges included in Cl.11
Cl.13 of IS 302-2-201: 2008(Leakage Current & Electric Strength at Operating Temperature)	-	3000	-
Cl.14 of IS 302‐2-201:2008(Transient Over Voltages )	-	2000	-
Cl.15 of IS 302-2-201:2008(Moisture Resistance )	-	4000	-
Cl.15 of IS 302-2-201:2008(Moisture Resistance )	-	0	Test charges included in Cl.15
Cl.16 of IS 302-2-201:2008(Leakage Current & Electric Strength)	-	3000	-
Cl.16 of IS 302-2-201:2008(Leakage Current & Electric Strength)	-	0	Test charges included in Cl.16
Cl.17 of IS 302‐2-201: 2008(Overload Protection of Transformers & Associated Circuits)	-	4000	-
Cl.19 of IS 302‐2-201: 2008(Abnormal Operation )	-	5000	-
Cl.19 of IS 302‐2-201: 2008(Abnormal Operation )	-	0	Test charges included in Cl.15
Cl.19 of IS 302‐2-201: 2008(Abnormal Operation )	-	0	Test charges included in Cl.15
Cl.19 of IS 302‐2-201: 2008(Abnormal Operation )	-	0	Test charges included in Cl.15
Cl.20 of IS 302-2-201: 2008(Stability & Mechanical Hazards)	-	2000	-
Cl.21 of IS 302-2-201: 2008(Mechanical Strength )	-	2000	-
Cl.21 of IS 302-2-201: 2008(Mechanical Strength )	-	0	Test charges included in Cl.21
Cl.21 of IS 302-2-201: 2008(Mechanical Strength )	-	0	Test charges included in Cl.21
Cl.22 of IS 302-2-201: 2008(Construction)	-	5000	-
Cl.23 of 302-2-201:2008(Internal Wiring )	-	2000	-
Cl.23 of 302-2-201:2008(Internal Wiring )	-	0	Test charges included in Cl.23
Cl.23 of 302-2-201:2008(Internal Wiring )	-	0	Test charges included in Cl.23
Cl.23 of 302-2-201:2008(Internal Wiring )	-	0	Test charges included in Cl.23
Cl.23 of 302-2-201:2008(Internal Wiring )	-	0	Test charges included in Cl.23
Cl.23 of 302-2-201:2008(Internal Wiring )	-	0	Test charges included in Cl.23
Cl.23 of 302-2-201:2008(Internal Wiring )	-	0	Test charges included in Cl.23
Cl.23 of 302-2-201:2008(Internal Wiring )	-	0	Test charges included in Cl.23
Cl.23 of 302-2-201:2008(Internal Wiring )	-	0	Test charges included in Cl.23
Cl.24 of IS 302-2-201: 2008(Component)	-	3000	-
Cl.24 of IS 302-2-201: 2008(Component)	-	0	Test charges included in Cl.24
Cl.24 of IS 302-2-201: 2008(Component)	-	0	Test charges included in Cl.24
Cl.24 of IS 302-2-201: 2008(Component)	-	0	Test charges included in Cl.24
Cl.24 of IS 302-2-201: 2008(Component)	-	0	Test charges included in Cl.24
Cl.24 of IS 302-2-201: 2008(Component)	-	0	Test charges included in Cl.24
Cl.24 of IS 302-2-201: 2008(Component)	-	0	Test charges included in Cl.24
Cl.24 of IS 302-2-201: 2008(Component)	-	0	Test charges included in Cl.24
Cl.24 of IS 302-2-201: 2008(Component)	-	0	Test charges included in Cl.24
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	2000	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Test charges included in Cl.25
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Test charges included in Cl.25
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Test charges included in Cl.25
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Test charges included in Cl.25
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Test charges included in Cl.25
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Test charges included in Cl.25
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Test charges included in Cl.25
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Test charges included in Cl.25
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Test charges included in Cl.25
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Test charges included in Cl.25
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Test charges included in Cl.25
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Test charges included in Cl.25
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Test charges included in Cl.25
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Test charges included in Cl.25
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Test charges included in Cl.25
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Test charges included in Cl.25
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Test charges included in Cl.25
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Test charges included in Cl.25
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Test charges included in Cl.25
Cl.26 of IS 302-2-201: 2008(Terminals for External Conductors)	-	1000	-
Cl.27 of IS 302-2-201: 2008(Provision for Earthing )	-	2000	-
Cl.27 of IS 302-2-201: 2008(Provision for Earthing )	-	0	Test charges included in Cl.27
Cl.27 of IS 302-2-201: 2008(Provision for Earthing )	-	0	Test charges included in Cl.27
Cl.27 of IS 302-2-201: 2008(Provision for Earthing )	-	0	Test charges included in Cl.27
Cl.27 of IS 302-2-201: 2008(Provision for Earthing )	-	0	Test charges included in Cl.27
Cl.27 of IS 302-2-201: 2008(Provision for Earthing )	-	0	Test charges included in Cl.27
Cl.28 of IS 302-2-201: 2008(Screws & Connections )	-	1000	-
Cl.29 of IS 302-2‐201:2008(Clearances, Creepage Distances and Solid Insulation )	-	2000	-
Cl.30 of IS 302-2‐201:2008(Resistance to Heat and Fire )	-	3000	-
Cl.31 of IS 302-2-201:2008(Resistance of Rusting )	-	0	-
Cl.32 of IS 302-2-201:2008(Radiation, Toxicity and Similar Hazards)	-	0	-
4(GENERAL REQUIREMENTS)	-	0	-
5(GENERAL CONDITIONS FOR THE TESTS)	-	0	-

-
Included w.e.f.20.06.2025 Exclusion (EMI/EMC)Cl 19.11.4.1 TO Cl 19.11.4.7

5438

Sierra Aircon Pvt. Ltd., Gurugram

8163426

IS 1391 : Part 2 (2018)

Room air conditioners - Specification: Part 2 split air conditioners (Third Revision)

Size

655000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause No. 8.2.2 (The Maximum Heating/Overload Test was conducted using a Balanced Ambient Room-Type Calorimeter. )	-	100000	The Maximum Heating/Overload Test was conducted using a Balanced Ambient Room-Type Calorimeter.
Heating Capacity test (Clause No. 8.2.1, 9.11), Power consumption test by heat pump (Clause No. 9.8)(The Heating capacity test was conducted using a Balanced Ambient Room-Type Calorimeter. )	-	50000	The Heating capacity test was conducted using a Balanced Ambient Room-Type Calorimeter.
Clause No. 5.1(Physical Verification)	-	0	Physical Verification
Clause No. 15.3.3(a)(Protection against access to the live part was conducted using Test Probe B.)	-	2000	Protection against access to the live part was conducted using Test Probe B.
Clause No. 15.2.5 & 15.3.3(c)(Provision for Earthing (Earth Resistance Test) was conducted using a Earth Continuity Tester. )	-	5000	Provision for Earthing (Earth Resistance Test) was conducted using a Earth Continuity Tester.
Clause No. 15.2.3 & 15.3.3(b)(High Voltage (Electric strength) Test was conducted using AC withstanding voltage/IR Tester. )	-	5000	High Voltage (Electric strength) Test was conducted using AC withstanding voltage/IR Tester.
Clause No. 15.2.4 & 15.3.3(d)( 3 Leakage Current at Operating Temperature (Leakage Current Test) was conducted using Leak Current Hitester.)	-	5000	Leakage Current at Operating Temperature (Leakage Current Test) was conducted using Leak Current Hitester.
Clause No. 14.3( Sound Test was conducted using Sound Level Meter. )	-	25000	Sound Test was conducted using Sound Level Meter.
Clause No. 8.1.3, 9.5( Freeze Up (Air Blockage Test & Drip Test) Test was conducted using a Balanced Ambient Room-Type Calorimeter. )	-	100000	Freeze Up (Air Blockage Test & Drip Test) Test was conducted using a Balanced Ambient Room-Type Calorimeter.
Clause No. 8.1.4, 9.6( Enclosure Sweat test was conducted using a Balanced Ambient Room-Type Calorimeter. )	-	50000	Enclosure Sweat test was conducted using a Balanced Ambient Room-Type Calorimeter.
Clause No. 8.1.2, 9.4(Maximum Operating test was conducted using a Balanced Ambient Room-Type Calorimeter. )	-	100000	Maximum Operating test was conducted using a Balanced Ambient Room-Type Calorimeter.
Cooling Capacity Test (Cl. No. 8.1.1, 9.9), Power Factor Test (Cl. No. 9.3), Power Consumption Test for Cooling (Cl. No. 9.7)(Cooling Capacity Test was conducted using a Balanced Ambient Room-Type Calorimeter. )	-	50000	Cooling Capacity Test was conducted using a Balanced Ambient Room-Type Calorimeter.
Cooling Capacity Test (Cl. No. 8.1.1, 9.9), Power Factor Test (Cl. No. 9.3), Power Consumption Test for Cooling (Cl. No. 9.7)(Cooling Capacity Test at Full Load and Half Load were conducted using a Balanced Ambient Room-Type Calorimeter. )	-	125000	Cooling Capacity Test at Full Load and Half Load were conducted using a Balanced Ambient Room-Type Calorimeter.
Clause No. 15.4.2( Pressure Test or Leakage Test was conducted prior to start of Cooling Capacity Test using a Balanced Ambient Room-Type Calorimeter. )	-	0	Pressure Test or Leakage Test was conducted prior to start of Cooling Capacity Test using a Balanced Ambient Room-Type Calorimeter.
Clause No. 8.2.2 (The Maximum Heating/Overload Test was conducted using a Balanced Ambient Room-Type Calorimeter. )	-	100000	-
Heating Capacity test (Clause No. 8.2.1, 9.11), Power consumption test by heat pump (Clause No. 9.8)(The Heating capacity test was conducted using a Balanced Ambient Room-Type Calorimeter. )	-	50000	-
Clause No. 5.1(Physical Verification)	-	0	-
Clause No. 15.3.3(a)(Protection against access to the live part was conducted using Test Probe B.)	-	2000	-
Clause No. 15.2.5 & 15.3.3(c)(Provision for Earthing (Earth Resistance Test) was conducted using a Earth Continuity Tester. )	-	5000	-
Clause No. 15.2.3 & 15.3.3(b)(High Voltage (Electric strength) Test was conducted using AC withstanding voltage/IR Tester. )	-	5000	-
Clause No. 15.2.4 & 15.3.3(d)( 3 Leakage Current at Operating Temperature (Leakage Current Test) was conducted using Leak Current Hitester.)	-	5000	-
Clause No. 14.3( Sound Test was conducted using Sound Level Meter. )	-	25000	-
Clause No. 8.1.3, 9.5( Freeze Up (Air Blockage Test & Drip Test) Test was conducted using a Balanced Ambient Room-Type Calorimeter. )	-	100000	-
Clause No. 8.1.4, 9.6( Enclosure Sweat test was conducted using a Balanced Ambient Room-Type Calorimeter. )	-	50000	-
Clause No. 8.1.2, 9.4(Maximum Operating test was conducted using a Balanced Ambient Room-Type Calorimeter. )	-	100000	-
Cooling Capacity Test (Cl. No. 8.1.1, 9.9), Power Factor Test (Cl. No. 9.3), Power Consumption Test for Cooling (Cl. No. 9.7)(Cooling Capacity Test was conducted using a Balanced Ambient Room-Type Calorimeter. )	-	50000	-
Cooling Capacity Test (Cl. No. 8.1.1, 9.9), Power Factor Test (Cl. No. 9.3), Power Consumption Test for Cooling (Cl. No. 9.7)(Cooling Capacity Test at Full Load and Half Load were conducted using a Balanced Ambient Room-Type Calorimeter. )	-	125000	-
Clause No. 15.4.2( Pressure Test or Leakage Test was conducted prior to start of Cooling Capacity Test using a Balanced Ambient Room-Type Calorimeter. )	-	0	-

31 Mar, 2028

-
-

5439

Sierra Aircon Pvt. Ltd., Gurugram

8163426

IS 1391 : Part 1 (2017)

Room air conditioners - Specification: Part 1 unitary air conditioners (Third Revision)

Size

665000 View breakup
-

31 Mar, 2028

-
-

5440

MARQUIS TECHNOLOGIES PRIVATE LIMITED, NOIDA

8175126

IS 10322 : PART 5 : SEC 3 (2012)

Luminaires: Part 5 particular requirements: Sec 3 luminaires for road and street lighting (First Revision)

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(General Test Requireements)	-	2000	-
5(Classification of Luminaires')	-	4000	-
6.0(Marking)	-	4000	-
7.0(Construction)	-	5000	-
8.0(Creepage Distance and Clearances)	-	5000	-
9.0(Provision for earthing)	-	8000	-
10.0(Terminals)	-	4000	-
11.0(External & Internal Wiring)	-	6000	-
12.0(Protection against electric shock)	-	4000	-
13.0(Endurance Tests and Thermal Tests)	-	8000	-
14.0(Resistance to Dust & Moisture)	-	0	-
15.0(Insulation Resistance and Electric Strength)	-	8000	-
16.0(Resistance to Heat , fire and tracking)	-	8000	-
17.0(Photometric Test)	-	8000	-

13 Dec, 2026

-
Included w.e.f 19.05.2025

5441

BUREAU VERITAS CONSUMER PRODUCTS SERVICES INDIA PRIVATE LIMITED, NOIDA

8127706

IS 302 : Part 2 : Sec 45 (1994)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 45 electric heating tools

56000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Rating)	-	0	-
6(Classification)	-	0	-
7(Marking)	-	2000	-
8(Protection against Access to Live Parts)	-	2000	-
9(Starting Of Motor Operated Appliances)	-	0	-
10("Power Input & Current")	-	2000	-
11(Temperature Rise/ Heating)	-	4000	-
12(Operation Under Overload Condition)	-	1000	-
13(Electric Insulation at Operating Temperature)	-	3000	-
14("Radio and Television Interference Suppression / Transient Over Voltage ")	-	0	-
15(Moisture Resistance)	-	4000	-
16(Insulation Resistance and Electric Strength/ Leakage Current and Electric Strength (After Humidity Treatment))	-	3000	-
17(Overload Protection/ Overload Protection of Transformers & Associated Circuits)	-	4000	-
18(Endurance)	-	0	-
19(Abnormal Operation)	-	5000	-
20(Stability & Mechanical Hazards)	-	2000	-
21(Mechanical strength)	-	2000	-
22(Construction)	-	5000	-
23(Internal Wiring)	-	2000	-
24(Components)	-	3000	-
25(Supply Connection & External Flexible Cords)	-	2000	-
26(Terminals For External Conductors)	-	1000	-
27(Provision For Earthing)	-	2000	-
28(Screws & Connections)	-	1000	-
29(Creepage Distances & Clearances)	-	2000	-
30(Resistance to Heat, Fire and Tracking)	-	3000	-
31(Radiation hazards)	-	0	-
XXV of Table 101(Resistance to Rusting)	-	0	-
4(General Requirement)	-	0	-

-
Included w.e.f.20.06.2025 Exclusion (EMI/EMC)Cl 19.11.4.1 TO Cl 19.11.4.7

5442

EMC Testing and Compliance LLP, Gurugram

8141526

IS 3735 (1996)

Canvas Shoes, Rubber Sole

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4.5 Consolidation Test IS 3400 (Part 5) : 1986 (From the quarter, cut a strip of 25.0 ± 0.5 mm width along the leagth of the boot and of sufficient length to permit separation over a length of 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100± 10mm per minute in accordance with IS 3400 (Part 5): 1986 or Static Dead Load Method as given in Annex C. The individual adhesion value for consolidation test shall not be less than 30N (3.0 kgf) for each of the teat piecea (see Note under 4.4).')	-	800	-
4.1.1 Upper, Sl No. (i) of Table 1(The upper shall consist of over layer of cotton, manmade or blended conforming' to the requirements given in Sl No. (i) of Table 1 as an overlayer and cotton drill conforming to the requirements given in Sl No. (ii) of Table 1, as an inner layer or lining. The two fabrics shall be firmly adhered together with rubber compound. )	-	500	-
Cl.4.1.1.1 Colour fastness(The dyed fabrics prescribed in 4.1.1 shall be fast todaylight and mechanical washing. Fastness to daylight shall be of rating 4 or better, when tested in accordance with IS 686 : 1985 or IS 2454: 1985. However in case of dispute the method prescribed in IS 686 : 1985 shall be considered as referee method.)	-	500	-
Cl.4.1.2 Binding Material(IS 1954 : 1990) (IS1969 : 1985)(Cotton tape NEWAR used as binding material shall conform to the requirements prescribed in col 3 of Table 2, when tested in accordance with the methods referred to in col 4 of the table.)	-	500	-
Cl.4.1.2.1 Anmex B.(Cotton, manmade or blended shall be used as binding material.' 'Coloured cotton tapes shall have fastness to day light of rating as and if agreed to between the purchaser and the supplier when tested in accordance with IS 686 : 1985. The black tapes shall be free from sulphur dyes when tested in accordance with Annex B.')	-	500	-
Cl.4.1.3.1( Sewing thread cotton, manmade or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other suitable thread shall have breaking load not less than above referred requirement of specification. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other suitable thread shall have breaking load not less than above referred requirement of specification.')	-	500	-
Cl.4.1.3.2 (IS 2454 : 1985) IS 765 : 1979 IS 971 : 1966( The colour of the threads shall be as agreedto between the purchaser and the supplier. The dyed threads shall conform to the following requirements or IS 686 : 1985'.)	-	500	-
Cl.4.1.4(.Brass, steel or aluminium eyelets of 7.5 mm diameter and wall thickness 0.30 to 0.35 mm shall be used.')	-	500	-
Cl.4.1.5 Laces( The shoes shall be provided with fabric braided laces either matching the shade of the upper or black or The length of the lace shall be 60 ± 3 cm )	-	500	-
Cl.4.1.6 Rubber Components(The rubber components shall conform to the requirements given in Table 4, when tested from finished boots.However in case it is not possible to cut the test pieces from the made up boots then 4.1.5.3 of IS 13695 : 1993 shall be followed.')	-	500	-
Cl.4.1.6.2 Ageing col 4 of Table 5.(The shoes shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the shoes shall conform to the physical requirements prescribed in col 4 of Table 5. )	-	500	-
Cl.4.1.6.2 Ageing (None of the rubber components of the shoes shall show any sign of tackiness or crack developed after ageing, when examined visually)	-	500	-
Cl.4.1.6.3 Thickness of components in Table 6.(Individual components of the shoes shall comply with the thickness and material requirements prescribed in Table 6.)	-	500	-
CL.4.2 Shape and Design IS 1638 : 1969(Cl 4.2.1 The shoes shall be made according to design and pattern as agreed to between the purchaser and the supplier. Size and fittings of the shoes shall be in accordance with IS 1638 : 1969 unless otherwise specified by the purchaser.)	-	2000	-
Cl.4.2.2( The recommended design of canvas shoes is shown in Fig. 1.)	-	500	-
Cl.4.3 Construction Cl 4.3.1( The upper shall be stitched on a lock stitch machine and the number of stitches shall be 30 to 40 per dm.)	-	1000	-
Cl.'4.3.2( Back of the upper shall be reinforced with a strip of upper material when there is a seam.')	-	500	-
Cl.4.3.3( The counter shall be stitched at the back, set from bottom of lining and bound flat on top edge with white/scoured binding material cut in bias and formed as a tape. T )	-	500	-
Cl.4.3.4 (The vantp shall be strengthened with a rubber toe-cap (see Fig. 1).)	-	500	-
Cl.4.3.5( Five pairs of eyelets shall be fitted in each shoe. The eyelets shall be properly clenched without any distortion. It shall properly match the colour of the upper canvas, or as agreed to between the purchaser and the supplier.)	-	500	-
Cl.4.3.6( The shoes shall be free from folds, wrinkles in the upper, blisters, embedded foreign matters and excessive surface markings. In appearance, general workmanship, finish and all other respects, not defined in the standard, the shoes shall be similar to the sample approved by the purchaser, if any)	-	500	-
CL.4.3.7( The soles shall be of even substance and ofone layer only.)	-	500	-
Cl.4.3.8( A rubber foxing shall be fixed all round the sole and heel. The colour shall be as agreed to between the purchaser and the supplier. )	-	500	-
Cl.4.4 Adhesion Test(From the upper-foxing portion where it is adhered to the canvas, parallel to the waist of sole, cut a strip of length 100 mm and width 8 mm. Separate out the plies initially by breaking the bond to a length of about 75 mm. Carry out the test on two specimens in accordance with IS 3400 (Part 5) : 1986. There shall be no further separation within 1 minute at a load of 1 kg for each of the two specimens.)	-	1000	-
CL.4.6 Mass(The mass of one pair of finished shoes of size 8 shall not exceed 750 g with an increase or decrease of 25 g for each bigger or smaller size respectively)	-	1000	-
4.1.1.2(Colorfastness to washing)	-	1000	-

19 Jul, 2027

-
-

5443

MARQUIS TECHNOLOGIES PRIVATE LIMITED, NOIDA

8175126

IS 10322 : Part 5 : Sec 2 (2012)

Luminaires: Part 5 particular requirements: Sec 2 recessed luminaires (First Revision)

45000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(General Test Requireements)	-	4000	-
5(Classification of Luminaires')	-	4000	-
6(Marking)	-	4000	-
7(Construction)	-	6000	-
8(Creepage Distance and Clearances)	-	8000	-
9(Provision for earthing)	-	6000	-
10(Terminals)	-	5000	-
11(External & Internal Wiring)	-	5000	-
12(Protection against electric shock)	-	4000	-
13(Endurance Tests and Thermal Tests)	-	8000	-
14(Resistance to Dust and Moisture)	-	5000	-
15(Insulation Resistance and Electric Strength)	-	6000	-
16(Resistance to Heat , fire and tracking)	-	6000	-
17(Photometric Test)	-	8000	-

13 Dec, 2026

-
Included w.e.f 19.05.2025

5444

BUREAU VERITAS CONSUMER PRODUCTS SERVICES INDIA PRIVATE LIMITED, NOIDA

8127706

IS 302 : Part 2 : Sec 35 (2017)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 35 electric instantaneous water heaters (Second Revision)

60000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.32(Verification)	-	0	Repeated clause
Cl.31(Verification)	-	0	Repeated clause
Cl.30(Verification)	-	0	Repeated clause
CL.29(Verification)	-	0	Repeated clause
Cl.28(Verification)	-	0	Repeated clause
Cl.27(Verification)	-	0	Repeated clause
Cl.26(Verification)	-	0	Repeated clause
Cl.25(Verification)	-	0	Repeated clause
Cl.24(Verification)	-	0	Repeated clause
Cl.23(Verification)	-	0	Repeated clause
Cl.22(Verification)	-	0	Repeated clause
Cl.21(Verification)	-	0	Repeated clause
Cl.20(Verification)	-	0	Repeated clause
Cl.19(Verification)	-	0	Repeated clause
Cl.17(Verification)	-	0	Repeated clause
Cl. 16(Verification)	-	0	Repeated clause
Cl.15(Verification)	-	0	Repeated clause
Cl.14(Verification)	-	0	Repeated clause
Cl.13(Verification)	-	0	Repeated clause
Cl.11(Verification)	-	0	Repeated clause
Cl.10(Verification)	-	0	Repeated clause
Cl.8(Verification)	-	0	Repeated clause
Cl. 7(Verification)	-	0	Repeated clause
Cl. 7(Verification)	-	0	Repeated clause
Cl. 32 IS 302-2-35(Radiation, Toxicity and similar hazards)	-	0	-
Cl. 31 IS 302-2-35(Resistance to Rusting)	-	0	-
Cl. 30 IS 302-2-35(Resistance to Heat Fire & Tracking )	-	3000	-
Cl. 29 IS 302-2-35(Clearances, Creepage Distances & Solid insulation )	-	2000	-
Cl. 28 IS 302-2-35(Screws & Connections)	-	1000	-
Cl. 27 IS 302-2-35(Provision for Earthing )	-	2000	-
Cl. 26 IS 302-2-35(Terminals for External conductors )	-	1000	-
Cl. 25 IS 302-2-35(Supply Connection & External Flexible Cords)	-	2000	-
Cl. 24 IS 302-2-35(Components)	-	3000	-
Cl. 23 IS 302-2-35(Internal Wiring)	-	2000	-
Cl. 22 IS 302-2-35(Construction )	-	8000	-
Cl. 21 IS 302-2-35(Mechanical strength)	-	2000	-
Cl. 20 IS 302-2-35(Stability & Mechanical Hazards)	-	2000	-
Cl. 19 IS 302-2-35(Abnormal Operation )	-	5000	-
Cl. 18 IS 302-2-35(Endurance)	-	0	-
Cl. 17 IS 302-2-35(Overload Protection of Transformers and Associated Circuit)	-	4000	-
Cl. 16 IS 302-2-35(Leakage Current & Electric Strength at Operating Temperature (After Humidity Treatment))	-	3000	-
Cl. 15 IS 302-2-35(Moisture Resistance Test )	-	4000	-
Cl. 14 IS 302-2-35(Radio and television interference suppression / Transient over voltages)	-	0	-
Cl. 13 IS 302-2-35(Leakage Current & Electric Strength at Operating Temperature)	-	3000	-
Cl. 11 IS 302-2-35(Heating)	-	4000	-
Cl. 10 IS 302-2-35(Power Input and Current )	-	2000	-
Cl. 9 IS 302-2-35(Starting of motor operated appliances)	-	0	-
Cl. 8 IS 302-2-35(Protection against access to live parts)	-	2000	-
Cl. 7 IS 302-2-35(Marking and Instruction)	-	2000	-
Cl. 6 IS 302-2-35(Classification)	-	0	-
5(GENERAL CONDITIONS FOR THE TESTS)	-	0	-
4(GENERAL REQUIREMENT)	-	0	-

-
Included w.e.f.20.06.2025 Exclusion (EMI/EMC)Cl 19.11.4.1 TO Cl 19.11.4.7

5445

KPML Low Voltage Rotating Machine and Hydraulic Laboratory Karad Projects and motors Limited

7187626

IS 8034 (2018)

Submersible pumpsets - Specification (Third Revision)

Bore Well Submersible Pump Set(0.37 to 75KW)

23526 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
14(Marking)	-	5000	-
14(Marking)	-	5000	-
14(Marking)	-	5000	-
14(Marking)	-	5000	-
14(Marking)	-	5000	-
14(Marking)	-	5000	-
14(Marking)	-	5000	-
14(Marking)	-	5000	-
14(Marking)	-	5000	-
14(Marking)	-	5000	-
14(Marking)	-	5000	-
14(Marking)	-	5000	-
14(Marking)	-	5000	-
14(Marking)	-	5000	-
14(Marking)	-	5000	-
14(Marking)	-	5000	-
14(Marking)	-	5000	-
14(Marking)	-	5000	-
14(Marking)	-	5000	-
6.1 (a)(Constructional Features)	-	10000	-
6.1 (b)(Constructional Features)	-	10000	-
6.1 (c)(Constructional Features)	-	10000	-
6.1 (d)(Constructional Features)	-	10000	-
6.1 (e)(Constructional Features)	-	10000	-
6.1 (f)(Constructional Features)	-	10000	-
6.2 (a)(Material of construction Part Sub Assembly Shaft Sleeve)	-	10000	-
6.2 (b)(Material of construction Part Sub Assembly Casing wear ring (if provided))	-	10000	-
6.2 (c)(Material of construction Part Sub Assembly Bush)	-	10000	-
6.2 (d)(Material of construction Part Sub Assembly Discharge casing (if provided))	-	10000	-
6.2 (e)(Material of construction Part Sub Assembly Impeller)	-	10000	-
6.2 (f)(Material of construction Part Sub Assembly Pump Bowl/Diffuser)	-	10000	-
6.2 (g)(Material of construction Part Sub Assembly Pump Shaft)	-	10000	-
6.2 (h)(Material of construction Part Sub Assembly Suction Casing)	-	10000	-
6.2.2.1(Gaskets, Seals and Packings)	-	10000	-
6.2.2.2(Gaskets, Seals and Packings)	-	10000	-
6.2.3(Gaskets, Seals and Packings)	-	10000	-
6.2.4(Gaskets, Seals and Packings)	-	10000	-
6.2.5(Gaskets, Seals and Packings)	-	10000	-
7.1.1(Design features: Typical design features 0f components of pump)	-	10000	-
7.1.2(Design features: Typical design features 0f components of pump)	-	10000	-
7.1.3(Design features: Typical design features 0f components of pump)	-	10000	-
7.1.4(Design features: Typical design features 0f components of pump)	-	9999.98	-
7.1.5(Design features: Typical design features 0f components of pump)	-	10000	-
7.1.6(Design features: Typical design features 0f components of pump)	-	10000	-
8.7.1(Direction of Rotation)	-	5000	-
8.7.2(Direction of Rotation)	-	5000	-
10.3(Hydrostatic Pressure Test)	-	5000	-
11.1.1(Guarantee of Performance)	-	23526	-
11.1.2(Guarantee of Performance)	-	23526	-
11.1.2(Guarantee of Performance)	-	23526	-
11.1.3(Guarantee of Performance)	-	23526	-
11.1.4(Guarantee of Performance)	-	23526	-
11.1.5(Guarantee of Performance)	-	23526	-
6(Measurement of shaft extension)	-	5000	-
6(Constructional Features)	-	10000	-
11(Guarantee of Performance)	-	23526	-
10(Pump Performance test)	-	23526	-
9.1(General)	-	23526	-
9.10 (a)(Insulation Resistance test)	-	5000	-
9.10 (b)(High Voltage test)	-	5000	-
9.10 (c)(Measurement of Stator Resistance)	-	5000	-
9.10 (d)(No Load Test at Rated Voltage)	-	5000	-
9.10 (e)(Reduced voltage Running up test)	-	5000	-
9.10 (f) & (g)(Locked Rotor Test)	-	5000	-
9.10 (h)(Leakage current test)	-	5000	-
9.10 (j)(Temperature Rise Test at Rated Voltage)	-	23526	-
9.10 (k)(Temperature rise test at reduced voltage)	-	23526	-
7.1.7(Pump loading shall be as per 11.1.5)	-	23526	-
7.1.9(prime mover electric motor suitable for the pumps shall be of contineous duty as specified in IS/IEC 60034-4 and as per IS 9283)	-	23526	-
9.10 m(Momentary over-load test)	-	23526	-
9.8(Speed)	-	23526	-
9.7(Breakaway (Starting)Torque Test)	-	10000	-
10.2.1(Measurement of Total Head)	-	23526	-
10.2.2(Flow Measurement)	-	23526	-
8.7(Direction of Rotation)	-	5000	-
7(Design features)	-	10000	-
10.2(Laboratory Tests Cl.8 of IS 11346-2002 Rate of flow and head Cl.8 of IS 11346-2002)	-	23526	-
10.2(Laboratory Tests Cl.8 of IS 11346-2002 Rate of flow and head Cl.8 of IS 11346-2002)	-	23526	-
10.2(Laboratory Tests Cl.8 of IS 11346-2002 Efficiency Cl.8.3 of IS 11346-2002)	-	23526	-
7.1.10(Voltage & Frequency variation)	-	23526	-
8.1(General Requirements)	-	2000	-
8.2(Casing)	-	2000	-
8.3(Impeller)	-	2000	-
8.4.1(Shaft)	-	2000	-
8.4.2(Shaft)	-	2000	-
8.8(Terminal Marking)	-	2000	-
8.9.1(Typical Installation)	-	2000	-
8.9.3(Typical Installation)	-	2000	-
12(Guarantee of workmanship and material)	-	2000	-
8.9(Typical installation)	-	2000	-
8.6(Submersible cable)	-	2000	-
8.6.1(Flat/Round cables as per IS694 shall be used)	-	2000	-
8.6.2(The size of the conductor shall be adequate and suitable for contineous use under water and in air. the length of the cable shall be minimum 2 m externallly unless otherwise specified by the customer)	-	2000	-
8.6.3(The size and of the cable should be suitably selected so that the voltage drop between control panel and the mptor terminal does not exeed three percent of the rated voltage)	-	2000	-
8.6.4(In case a joint is required to be made between the lead cable supplied with the motor and the user’s cable, a detailed procedure to make water tight joining shall be supplied by the motor manufacturer.)	-	2000	-
8.9(Installation)	-	2000	-
8.9.2(The pumpset shall be installed as per guidelines laid down in IS 14536 or as per the recommendation of the manufacturer)	-	2000	-
8.9.4.1(Earthing of the motor shall be done as per IS 9283 in accordance with the relevant provisions of IS 3043.)	-	2000	-
8.9.4.2(In case of PVC pipes used as discharge pipe, a separate non corrosive, low resistance conductor from motor earth terminal to control panel earth terminal shall be provided for earthing.)	-	2000	-
8.9.4.3(In case non corrosive GI pipes and clamps are used for the purpose of earthing the motor, earthing connection may be made to the discharge pipe clamp and to the control panel earth terminal)	-	2000	-
8.1(GENERAL REQUIREMENTS)	-	2000	-

26 Aug, 2028

-
Exclusion: Cl 8.5.1 (Balancing), Cl 8.5 (Balancing of rotor), Cl 8.8 (Terminal Marking), Cl 8.9.1 (Typical Installation), Cl 8.9.3 (Typical Installation), Cl 12 (Guarantee of workmanship and material), Cl 8.6 (Submersible cable), Cl 8.9.4c (Earthing)

5446

BUREAU VERITAS CONSUMER PRODUCTS SERVICES INDIA PRIVATE LIMITED, NOIDA

8127706

IS 302 : Part 2 : Sec 32 (1994)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 32 massage appliances

57000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 32 302-2-32 : 1994(Radiation Hazards)	-	0	-
Cl. 31 302-2-32 : 1994(Resistance to Rusting)	-	0	-
Cl. 30 302-2-32 : 1994(Resistance to Heat Fire & Tracking )	-	3000	-
Cl. 29 302-2-32 : 1994(Clearances, Creepage Distances & Solid insulation )	-	2000	-
Cl. 28 302-2-32 : 1994(Screws & Connections)	-	1000	-
Cl. 27 302-2-32 : 1994(Provision for Earthing )	-	2000	-
Cl. 26 302-2-32 : 1994(Terminals for External conductors )	-	1000	-
Cl. 25 302-2-32 : 1994(Supply Connection & External Flexible Cords)	-	2000	-
Cl. 24 302-2-32 : 1994(Components)	-	3000	-
Cl. 23 302-2-32 : 1994(Internal Wiring)	-	2000	-
Cl. 22 302-2-32 : 1994(Construction )	-	5000	-
Cl. 21 302-2-32 : 1994(Mechanical strength)	-	2000	-
Cl. 20 302-2-32 : 1994(Stability & Mechanical Hazards)	-	2000	-
Cl. 19 302-2-32 : 1994(Abnormal Operation )	-	5000	-
Cl. 18 302-2-32 : 1994(Endurance)	-	0	-
Cl. 17 302-2-32 : 1994(Overload Protection of Transformers and Associated Circuit)	-	4000	-
Cl. 16 302-2-32 : 1994(Leakage Current & Electric Strength at Operating Temperature (After Humidity Treatment))	-	3000	-
Cl. 15 302-2-32: 1994(Moisture Resistance Test )	-	4000	-
Cl. 14 302-2-32 : 1994(Radio and television interference suppression / Transient over voltages)	-	2000	-
Cl. 13 302-2-32 : 1994(Leakage Current & Electric Strength at Operating Temperature)	-	3000	-
Cl. 11 302-2-32 : 1994(Temperature Rise)	-	4000	-
Cl. 10 302-2-32 : 1994(Power Input and Current )	-	2000	-
Cl. 9 302-2-32 : 1994(Protection Against Electric Shock)	-	0	-
Cl. 8 302-2-32 : 1994(Starting of motor operated appliances)	-	2000	-
Cl. 7 302-2-32 : 1994(Marking)	-	2000	-
(CI. 6 IS 302-2-32 : 1994(Classification )	-	0	-
Cl. 32 302-2-32 : 1994(Radiation Hazards)	-	-	-
Cl. 31 302-2-32 : 1994(Resistance to Rusting)	-	-	-
Cl. 30 302-2-32 : 1994(Resistance to Heat Fire & Tracking )	-	-	-
Cl. 29 302-2-32 : 1994(Clearances, Creepage Distances & Solid insulation )	-	-	-
Cl. 28 302-2-32 : 1994(Screws & Connections)	-	-	-
Cl. 27 302-2-32 : 1994(Provision for Earthing )	-	-	-
Cl. 26 302-2-32 : 1994(Terminals for External conductors )	-	-	-
Cl. 25 302-2-32 : 1994(Supply Connection & External Flexible Cords)	-	-	-
Cl. 24 302-2-32 : 1994(Components)	-	-	-
Cl. 23 302-2-32 : 1994(Internal Wiring)	-	-	-
Cl. 22 302-2-32 : 1994(Construction )	-	-	-
Cl. 21 302-2-32 : 1994(Mechanical strength)	-	-	-
Cl. 20 302-2-32 : 1994(Stability & Mechanical Hazards)	-	-	-
Cl. 19 302-2-32 : 1994(Abnormal Operation )	-	-	-
Cl. 18 302-2-32 : 1994(Endurance)	-	-	-
Cl. 17 302-2-32 : 1994(Overload Protection of Transformers and Associated Circuit)	-	-	-
Cl. 16 302-2-32 : 1994(Leakage Current & Electric Strength at Operating Temperature (After Humidity Treatment))	-	-	-
Cl. 15 302-2-32: 1994(Moisture Resistance Test )	-	-	-
Cl. 14 302-2-32 : 1994(Radio and television interference suppression / Transient over voltages)	-	-	-
Cl. 13 302-2-32 : 1994(Leakage Current & Electric Strength at Operating Temperature)	-	-	-
Cl. 11 302-2-32 : 1994(Temperature Rise)	-	-	-
Cl. 10 302-2-32 : 1994(Power Input and Current )	-	-	-
Cl. 9 302-2-32 : 1994(Protection Against Electric Shock)	-	-	-
Cl. 8 302-2-32 : 1994(Starting of motor operated appliances)	-	-	-
Cl. 7 302-2-32 : 1994(Marking)	-	-	-
(CI. 6 IS 302-2-32 : 1994(Classification )	-	-	-

-
Included w.e.f.20.06.2025 Exclusion (EMI/EMC)Cl 19.11.4.1 TO Cl 19.11.4.7

5447

Sleen India Biz venture Private Limited, Agra

9139736

IS 12084 (2018)

Morpholine - Specification (First Revision)

INDUSTRIAL CHEMICAL

10300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.3 - Table 1 - Sl No - vi(Chloride ( as Cl ) I IS 3025 (Part 32)	-	1000	-
4.3 - Table 1 - Sl No - x(Silica ( as SiO2 ) - IS 3025 (Part 35))	-	1000	-
4.3 - Table 1 - Sl No - ix(Nickel ( as Ni ) - IS 3025 (Part 54))	-	1000	-
4.3 - Table 1 - Sl No - viii(Copper ( as Cu ) - IS 3025 (Part 42))	-	1000	-
4.3 - Table 1 - Sl No - vii(Iron ( as Fe ) - IS 3025 (Part 53))	-	1000	-
4.3 - Table 1 - Sl No - vi(Ash content - Annex E)	-	500	-
4.3 - Table 1 - Sl No - v(Residue, on evaporation - Annex D)	-	500	-
4.3 - Table 1 - Sl No - iv(Boiling range for for 90 percent recovery - IS 5298)	-	500	-
4.3 - Table 1 - Sl No - iii(Colour (Pt-Co-Scale ) - IS 3025(Part 4))	-	500	-
4.3 - Table 1 - Sl No - ii(Relative density, 20/20 oC - Annex C)	-	500	-
4.3 - Table 1 - Sl No - i(Purity (as Morpholine) - Annex B)	-	500	-
4.2(IS 11255 (Part 6))	-	500	-
4.1(Description)	-	300	-
4.1(Requirement)	-	200	-
4.2(The material shall not contain any free ammonia, IS 11255 part-6)	-	0	Test price for clause 4.2 is 500/-
5.1(Packing)	-	150	-
5.2(Marking)	-	150	-
4.3 & 7.1 - Table -1, Sl no. 1(Purity (as Morpholine), percent by mass, Annex B)	-	0	Test price for clause 4.3 table 1-i is 500/-.
4.3 & 7.1 - Table -1, Sl no. 2(Relative density, 20/20oC, Annex C)	-	0	Test price for clause 4.3 table 1-ii is 500/-.
4.3 & 7.1 - Table -1, Sl no. 3(Colour (Pt-Co-Scale ), IS 3025 part-4)	-	0	Test price for clause 4.3 table 1-iii is 500/-.
4.3 & 7.1 - Table -1, Sl no. 4(Boiling range, IS 5298)	-	0	Test price for clause 4.3 table 1-v is 500/-.
4.3 & 7.1 - Table -1, Sl no. 5(Residue, on evaporation, mg/l, Annex D)	-	0	Test price for clause 4.3 table 1-v is 500/-.
4.3 & 7.1 - Table -1, Sl no. 6(Ash content, g/100 ml, Annex E)	-	0	Test price for clause 4.3 table 1-vi is 500/-.
4.3 & 7.1 - Table -1, Sl no. 7(Iron ( as Fe ), ppm, IS 3025 part 53)	-	0	Test price for clause 4.3 table 1-vii is 1000/-.
4.3 & 7.1 - Table -1, Sl no. 8(Copper ( as Cu ), ppm, IS 3025 (Part 42))	-	0	Test price for clause 4.3 table 1-viii is 1000/-.
4.3 & 7.1 - Table -1, Sl no. 9(Nickel ( as Ni ), ppm, IS 3025 (Part 54))	-	0	Test price for clause 4.3 table 1-ix is 1000/-.
4.3 & 7.1 - Table -1, Sl no. 10(Silica ( as SiO2 ), ppm, IS 3025 (Part 35))	-	0	Test price for clause 4.3 table 1-x is 1000/-.
4.3 & 7.1 - Table -1, Sl no. 11(Chloride ( as Cl), ppm, IS 3025 (Part 32))	-	0	Test price for clause 4.3 table 1-vi is 1000/-.
4.1(Requirement)	-	0	-
4.2(The material shall not contain any free ammonia, IS 11255 part-6)	-	0	-
5.1(Packing)	-	0	-
5.2(Marking)	-	0	-
4.3 & 7.1 - Table -1, Sl no. 1(Purity (as Morpholine), percent by mass, Annex B)	-	0	-
4.3 & 7.1 - Table -1, Sl no. 2(Relative density, 20/20oC, Annex C)	-	0	-
4.3 & 7.1 - Table -1, Sl no. 3(Colour (Pt-Co-Scale ), IS 3025 part-4)	-	0	-
4.3 & 7.1 - Table -1, Sl no. 4(Boiling range, IS 5298)	-	0	-
4.3 & 7.1 - Table -1, Sl no. 5(Residue, on evaporation, mg/l, Annex D)	-	0	-
4.3 & 7.1 - Table -1, Sl no. 6(Ash content, g/100 ml, Annex E)	-	0	-
4.3 & 7.1 - Table -1, Sl no. 7(Iron ( as Fe ), ppm, IS 3025 part 53)	-	0	-
4.3 & 7.1 - Table -1, Sl no. 8(Copper ( as Cu ), ppm, IS 3025 (Part 42))	-	0	-
4.3 & 7.1 - Table -1, Sl no. 9(Nickel ( as Ni ), ppm, IS 3025 (Part 54))	-	0	-
4.3 & 7.1 - Table -1, Sl no. 10(Silica ( as SiO2 ), ppm, IS 3025 (Part 35))	-	0	-
4.3 & 7.1 - Table -1, Sl no. 11(Chloride ( as Cl), ppm, IS 3025 (Part 32))	-	0	-
4.1(Requirement)	-	0	-
4.2(The material shall not contain any free ammonia, IS 11255 part-6)	-	0	-
5.1(Packing)	-	0	-
5.2(Marking)	-	0	-
4.3 & 7.1 - Table -1, Sl no. 1(Purity (as Morpholine), percent by mass, Annex B)	-	0	-
4.3 & 7.1 - Table -1, Sl no. 2(Relative density, 20/20oC, Annex C)	-	0	-
4.3 & 7.1 - Table -1, Sl no. 3(Colour (Pt-Co-Scale ), IS 3025 part-4)	-	0	-
4.3 & 7.1 - Table -1, Sl no. 4(Boiling range, IS 5298)	-	0	-
4.3 & 7.1 - Table -1, Sl no. 5(Residue, on evaporation, mg/l, Annex D)	-	0	-
4.3 & 7.1 - Table -1, Sl no. 6(Ash content, g/100 ml, Annex E)	-	0	-
4.3 & 7.1 - Table -1, Sl no. 7(Iron ( as Fe ), ppm, IS 3025 part 53)	-	0	-
4.3 & 7.1 - Table -1, Sl no. 8(Copper ( as Cu ), ppm, IS 3025 (Part 42))	-	0	-
4.3 & 7.1 - Table -1, Sl no. 9(Nickel ( as Ni ), ppm, IS 3025 (Part 54))	-	0	-
4.3 & 7.1 - Table -1, Sl no. 10(Silica ( as SiO2 ), ppm, IS 3025 (Part 35))	-	0	-
4.3 & 7.1 - Table -1, Sl no. 11(Chloride ( as Cl), ppm, IS 3025 (Part 32))	-	0	-
4.1(Requirement)	-	0	-
4.2(The material shall not contain any free ammonia, IS 11255 part-6)	-	0	-
5.1(Packing)	-	0	-
5.2(Marking)	-	0	-
4.3 & 7.1 - Table -1, Sl no. 1(Purity (as Morpholine), percent by mass, Annex B)	-	0	-
4.3 & 7.1 - Table -1, Sl no. 2(Relative density, 20/20oC, Annex C)	-	0	-
4.3 & 7.1 - Table -1, Sl no. 3(Colour (Pt-Co-Scale ), IS 3025 part-4)	-	0	-
4.3 & 7.1 - Table -1, Sl no. 4(Boiling range, IS 5298)	-	0	-
4.3 & 7.1 - Table -1, Sl no. 5(Residue, on evaporation, mg/l, Annex D)	-	0	-
4.3 & 7.1 - Table -1, Sl no. 6(Ash content, g/100 ml, Annex E)	-	0	-
4.3 & 7.1 - Table -1, Sl no. 7(Iron ( as Fe ), ppm, IS 3025 part 53)	-	0	-
4.3 & 7.1 - Table -1, Sl no. 8(Copper ( as Cu ), ppm, IS 3025 (Part 42))	-	0	-
4.3 & 7.1 - Table -1, Sl no. 9(Nickel ( as Ni ), ppm, IS 3025 (Part 54))	-	0	-
4.3 & 7.1 - Table -1, Sl no. 10(Silica ( as SiO2 ), ppm, IS 3025 (Part 35))	-	0	-
4.3 & 7.1 - Table -1, Sl no. 11(Chloride ( as Cl), ppm, IS 3025 (Part 32))	-	0	-

-
Included w.e.f 04.07.2025

5448

EMC Testing and Compliance LLP, Gurugram

8141526

IS 15844 : Part 2 (2023)

SPORTS FOOTWEAR PART -2 PERFORMANCE SPORTS FOOTWEAR

68000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.12, Table no. 1 of IS 17011,(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	3500	-
7.12, Table no. 1 of IS 17011,(xi)(Phthalates (each individual phthalate))	-	6000	-
7.12, Table no. 1 of IS 17011,(x)(pH)	-	500	-
7.12, Table no. 1 of IS 17011,(ix)(PCP-TeCP-TriCP polychlorophenols)	-	4500	-
7.12, Table no. 1 of IS 17011,(viii)(Organotin compounds)	-	7000	-
7.12, Table no. 1 of IS 17011,(vii)(Formaldehyde)	-	2500	-
7.12, Table no. 1 of IS 17011,(v)(Dimethyl fumarate (DMFU))	-	5000	-
7.12, Table no. 1 of IS 17011,(iv)(Chromium (VI))	-	2100	-
7.12, Table no. 1 of IS 17011,(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	3700	-
7.12, Table no. 1 of IS 17011,(i)(Allergenic and carcinogenic disperse dyes)	-	4500	-
8(MARKING AND PACKING)	-	180	-
4(SAMPLING AND CONDITIONING)	-	180	-
5(DESIGN)	-	180	-
6(SIZE AND FITTINGS)	-	180	-
7.1.1(Whole Footwear)	-	180	-
7.1.2(Upper to Mid Sole/Out Sole Bond Performance)	-	1080	-
7.1.3("Upper to Composite Sole Bond Performance (Applicable Only When the Sole is Composite)")	-	1080	-
7.1.4(Out Sole to Mid Sole (Multilayer) Bond Performance)	-	1080	-
7.1.5(Energy Absorption at Seat Region)	-	700	-
7.1.6(Complete Shoe Flexing)	-	1500	-
7.1.7(Washability)	-	1000	-
7.1.8(Slip Resistance)	-	2500	-
7.1.9(Heel Drop)	-	180	-
7.2 , Table No. 2 , i)(Flexing resistance)	-	1500	-
7.2 , Table No. 2 , ii)(Tear strength (average force))	-	500	-
7.2 , Table No. 2 , iii)("Colour fastness rubbing (To and fro) Grey scale rate Dry: (rubbing) Rating: (Marring and staining) ")	-	500	-
7.2 , Table No. 2 , iv) ,a)(Water vapour permeability)	-	700	-
7.2 , Table No. 2 , vii)(Tensile strength)	-	500	-
7.2 , Table No. 2 , viii)(Elongation at break,)	-	500	-
7.2 , Table No. 2 , ix)("Water penetration and water absorption after 60 Minutes Water absorption %, Max Water penetration Gms, Max")	-	700	-
7.2 , Table No. 2 , x)(Abrasion test (for unlined upper))	-	1350	-
7.2 , Table No. 3 , i)(Breaking strength "As per Method 1 of IS 7016 (Part 2)/ ISO 1421 : 2016 or ISO 17706")	-	500	-
7.2 , Table No. 3 , ii)(Elongation at break)	-	500	-
7.2 , Table No. 3 , iii)(Tear strength, N, Min For Fabric: For all other materials)	-	500	-
7.2 , Table No. 3 , iv)(Strength at needle perforation)	-	600	-
7.2 , Table No. 3 , v)("Flexing resistance, no crack/damage to coating/ lamination / upper material till prescribed cycles")	-	1500	-
7.2 , Table No. 3 , vi) , a)(Water vapour permeability,)	-	700	-
7.2 , Table No. 3 , vi) , b)("Water vapour coefficient, ")	-	700	-
7.2 , Table No. 3 , vii)(Hydrolysis resistance)	-	2700	-
7.2 , Table No. 3 , viii)(Colour fastness to light grey scale rate)	-	300	-
7.2 , Table No. 3 , ix)(Bursting Strength,)	-	1000	-
7.3 , Table No. 4 , ii)(Abrasion resistance, cycles)	-	500	-
7.3 , Table No. 4 , i)(Tear strength,)	-	500	-
7.3 , Table No. 4 , iii)("Colour fastness to rubbing (crocking), Grey scale rate with 10 rubs on dry or wet, ")	-	500	-
7.3 , Table No. 4 , iv)("Colour fastness to perspiration (contact method) Grey scale rate, ")	-	300	-
7.3 , Table No. 4 , v) , b)("Water vapour coefficient, " As per IS 15298 (Part 1))	-	700	-
7.4 , Table No. 5 , i)(Thickness)	-	180	-
7.4 , Table No. 5 , ii)(Flexing index)	-	800	-
7.4 , Table No. 5 , iii)(Abrasion resistance, at 400 cycles)	-	1350	-
7.4 , Table No. 5 , iv) , a)(Water Absorption,)	-	700	-
7.4 , Table No. 5 , iv) , b)(Water Desorption)	-	700	-
7.5 , Table No. 6 , i)(Thickness)	-	180	-
7.5 , Table No. 6 , ii)(Abrasion resistance, cycles As per IS 15298 (Part 1))	-	1350	-
7.5 , Table No. 6 , iii) , a)(Water Absorption)	-	700	-
7.5 , Table No. 6 , iv)(Heat resistance shrinkage linear)	-	1000	-
7.6 , Table No. 7 , i)(Abrasion resistance (volume loss))	-	1350	-
7.6 , Table No. 7 , ii)(Flexing resistance)	-	1080	-
7.6 , Table No. 7 , iii)(Hydrolysis resistance, cut growth after 1 50 000 flexes)	-	2700	-
7.6 , Table No. 7 , iv)(Tear strength)	-	500	-
7.6 , Table No. 7 , v)(Tensile strength)	-	500	-
7.8 , Table No. 9 , i)(First dry collapsing load, hardness)	-	800	-
7.6 , Table No. 7 , vii)(Compression set)	-	800	-
7.7 , Table No. 8 , i)(Compression set)	-	800	-
7.7 , Table No. 8 , ii)(Split tear strength,)	-	500	-
7.7 , Table No. 8 , iii)(Heat shrinkage,)	-	1000	-
7.8 , Table No. 9 , ii)(Resilience)	-	800	-
7.8 , Table No. 9 , iii)(Moisture resistance)	-	800	-
7.8 , Table No. 9 , iv) , a)(Initial dry area shape retention)	-	800	-
7.8 , Table No. 9 , iv) , b)(Area shape retention after 10th collapse, dry)	-	800	-
7.8 , Table No. 9 , v)(Peel strength)	-	1500	-
7.9 , Table No. 10 , i)(Peel strength)	-	1500	-
7.9 , Table No. 10 , ii)(Shear strength)	-	1500	-
7.10 , Table No. 11 , i)(Limit of useful extension,)	-	1000	-
7.10 , Table No. 11 , ii)(Needle strength,)	-	600	-
7.11 , Table No. 12 , i)(Breaking strength of lace,)	-	500	-
7.11 , Table No. 12 , ii)(Lace tag strength,)	-	500	-
7.11 , Table No. 12 , iii)(Lace to lace abrasion,)	-	800	-
7.11 , Table No. 12 , iv)("Colour fastness to water Gray Scale Rate")	-	500	-
7.11 , Table No. 12 , v)(Strength of Buckle/Ski hook)	-	800	-
7.11 , Table No. 12 , vi)(Corrosion resistance)	-	900	-
7.12("Chemical Requirement on Complete Product for All Types of Sports Shoe")	-	35000	TOTAL PRICE WITH CHEMICAL TEST 68000; WITHOUT CHEMICAL TEST 33000 10% DISCOUNT TO BIS
7.12.2 (Amendment 1)(Lead content)	-	5000	-
7.12.2 (Amendment 1)(Lead content)	-	2000	-

19 Jul, 2027

-
-

5449

Atmy Analytical Labs Private Limited (Unit-2), Greater Noida

8176106

IS 17550 : Part 1 (2024)

Household Refrigerating Appliances - Characteristics and Test Methods Part 1 General Requirements (First Revision)

ALL

218000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(MARKING)	-	2500	-
8(MATERIALS, DESIGN, AND MANUFACTURE)	-	15000	-
9(Testing The Air Tightness Of Door Or Lid Seal(S))	-	3000	-
10(Testing The Opening Force Of Door(S) Or Lid(S))	-	10000	-
11(Testing The Durability Of Hinges And Handles Of Door(S) And Lid(S)	-	50000	-
12(Testing The Mechanical Strength Of Shelves And Similar Components)	-	10000	-
14(Ice-Making Test (If Applicable))	-	30000	-
15(Test For Absence Of Odour And Taste)	-	50000	-
16(Safety Requirements)	-	50000	-
5(MARKING)	-	0	-
8(MATERIALS, DESIGN, AND MANUFACTURE)	-	0	-
9(Testing The Air Tightness Of Door Or Lid Seal(S))	-	0	-
10(Testing The Opening Force Of Door(S) Or Lid(S))	-	0	-
11(Testing The Durability Of Hinges And Handles Of Door(S) And Lid(S)	-	0	-
12(Testing The Mechanical Strength Of Shelves And Similar Components)	-	0	-
14(Ice-Making Test (If Applicable))	-	0	-
15(Test For Absence Of Odour And Taste)	-	0	-
16(Safety Requirements)	-	0	-

08 Feb, 2027

-
Included w.e.f 29.04.2025

5450

Gravitas Laboratories Private Limited, Greater Noida

8182606

IS 280 (2006)

Mild steel wire for general engineering purposes (Fourth Revision)

All size

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	500	-
Cl 9(Tensile Test On UTM)	-	500	-
Cl 11(Workmanship)	-	500	-
Cl 13(Workmanship)	-	500	-
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	500	-
Cl 9(Tensile Test On UTM)	-	500	-
Cl 11(Workmanship)	-	500	-
Cl 13(Workmanship)	-	500	-
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	500	-
Cl 9(Tensile Test On UTM)	-	500	-
Cl 11(Workmanship)	-	500	-
Cl 13(Workmanship)	-	500	-
6 AND AS PER IS 7887(MICRO ALLOY)	-	500	-
6 AND AS PER IS 7887(ALUMINIUM)	-	500	-
6 AND AS PER IS 7887(PHOSPHORUS)	-	500	-
6 AND AS PER IS 7887(SULPHUR)	-	500	-
6 AND AS PER IS 7887(MANGANESE)	-	500	-
6 AND AS PER IS 7887(SILICON)	-	500	-
6 AND AS PER IS 7887(CARBON)	-	500	-
7 & 8(Ovality)	-	500	-
7 & 8(Diameter)	-	500	-
9.2(Wrapping Test)	-	1500	-
9.3(Bend test)	-	1000	-
10(Finish)	-	500	-
11(Coating test)	-	800	-
13(Freedom from defects)	-	800	-
Cl 13(Workmanship)	-	800	-
Cl 11(Workmanship)	-	800	-
Cl 9(Tensile Test On UTM)	-	800	-
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	880	-
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	500	-
Cl 9(Tensile Test On UTM)	-	500	-
Cl 11(Workmanship)	-	500	-
Cl 13(Workmanship)	-	500	-
Clause 6 and Note 3 of IS 7887(Any Instrumental Method/Chemical Method)	-	500	-
Clause 6 and Note 3 of IS 7887(Copper)	-	500	-
Clause 6 and Note 3 of IS 7887(Copper)	-	500	-
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	0	-
Cl 9(Tensile Test On UTM)	-	0	-
Cl 11(Workmanship)	-	0	-
Cl 13(Workmanship)	-	0	-
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	0	-
Cl 9(Tensile Test On UTM)	-	0	-
Cl 11(Workmanship)	-	0	-
Cl 13(Workmanship)	-	0	-
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	0	-
Cl 9(Tensile Test On UTM)	-	0	-
Cl 11(Workmanship)	-	0	-
Cl 13(Workmanship)	-	0	-
9.3(Bend test)	-	0	-
10(Finish)	-	0	-
11(Coating test)	-	0	-
13(Freedom from defects)	-	0	-
Cl 13(Workmanship)	-	0	-
Cl 11(Workmanship)	-	0	-
Cl 9(Tensile Test On UTM)	-	0	-
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	0	-
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	0	-
Cl 9(Tensile Test On UTM)	-	0	-
Cl 11(Workmanship)	-	0	-
Cl 13(Workmanship)	-	0	-
Clause 6 and Note 3 of IS 7887(Any Instrumental Method/Chemical Method)	-	0	-
Clause 6 and Note 3 of IS 7887(Copper)	-	0	-
Clause 6 and Note 3 of IS 7887(Copper)	-	0	-

-
Included w.e.f 22.07.2025

5451

MSME Testing Centre, New Delhi

8101204

IS 4246 (2002)

Domestic gas stoves for use with liquefied petroleum gases - Specification (Fifth Revision)

16100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.24(Annexure E)(on no account the carbon monoxidel carbon dioxide ratio of the exhaust gases of any burner. operating at any consumption at which the burner is stable at gas inlet pressure from 2452 kN/m2 to 3432 kN/m2 (25 gf/cm2 to 35 gf/cm2), exceed 0.02.)	-	300	-
Cl.23(There shall be no extinction of the flames on any of the burners operating at maximum consumption when the appliance is placed in a general (not localized) current of air with a velocity of 2 m/s, as measured with a rotating vane anemometer. The location of the appliance relative to neighboring walls and the direction of the draught shall be varied to correspond to likely conditions of appliance installation. This applies for all pressures from 2452 kN/m2 to 3432 kN/m2 (25 gf/cm2 to 35 gf/cm2).)	-	300	-
4.1(Requirement)	-	300	-
5(Materials)	-	2500	-
6(Design for Maintenance)	-	300	-
7(Rigidity and Stability)	-	300	-
8(Workmanship and Finish)	-	300	-
9(Gas Taps)	-	2400	-
10(Injector Jets)	-	1500	-
11(Burners)	-	300	-
12(Burner Pan Supports)	-	300	-
13.1(Gas Soundness)	-	300	-
14(Gas Inlet Connections)	-	2100	-
15(Strength and Rigidity)	-	300	-
17.1.1(Gas Consumption)	-	300	-
18(Ignition and Flame Travel)	-	300	-
19(Flame Stability)	-	300	-
20(Noise Control)	-	300	-
21(Flash Back)	-	300	-
22(Formation of Soot)	-	300	-
23(Resistance to Draught)	-	300	-
25(Fire Hazard and Limiting Temperature)	-	1000	-
26(Thermal Efficiency)	-	3000	-
5.1.2(Toughened glass- Adhesive tape)	-	300	-
5.1.3(Thermal Shock test)	-	300	-

31 Dec, 2026

-
-

5452

Saturn Quality Certifications Pvt.Ltd., Bahadurgarh

8133016

IS 10500 (2012)

Drinking water - Specification (Second Revision)

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4, table 4, i, a)(Alpha emitters)	-	2000	+ 18% GST (as applicable)
4, table 4, i, b)(Beta emitters)	-	2000	+ 18% GST (as applicable)
Table 3, x)(Uranium)	-	3000	+ 18% GST (as applicable)

03 Feb, 2028

-
-

5453

UL INDIA PRIVATE LIMITED, BENGALURU

6120526

IS 14286 : Part 1 (2023)

Terrestrial Photovoltaic PV Modules Design Qualification and Type Approval Part 1: Test Requirements (Third Revision)

PHOTOVOLTAIC (PV) MODULE

2349500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Visual inspection (MQT 01))	-	30000	-
4.2(Maximum power determination (MQT 02))	-	26000	-
4.3(Insulation test (MQT 03))	-	70000	-
4.4(Measurement of temperature coefficients (MQT 04))	-	100000	-
4.6(Performance at STC (MQT 06.1))	-	42000	-
4.7(Performance at low irradiance (MQT 07))	-	19500	-
4.8(Outdoor exposure test (MQT 08))	-	80000	-
4.9(Hot-spot endurance test (MQT 09))	-	25000	-
4.10(UV preconditioning test (MQT 10))	-	120000	-
4.11(Thermal cycling test (MQT 11))	-	400000	-
4.12(2 Humidity-freeze test (MQT 12))	-	250000	-
4.13(Damp heat test (MQT 13))	-	400000	-
4.14(Robustness of terminations (MQT 14))	-	12000	-
4.15(5 Wet leakage current test (MQT 15))	-	65000	-
4.16(Static mechanical load test (MQT 16))	-	20000	-
4.17(Hail test (MQT 17))	-	20000	-
4.18(Bypass diode testing (MQT 18))	-	20000	-
4.19(Stabilization (MQT 19))	-	150000	-
4.20(Cyclic (dynamic) mechanical load test (MQT 20))	-	80000	-
4.21(Potential induced degradation test (MQT 21))	-	350000	-
4.22(Bending test (MQT 22))	-	70000	-
4.5(Placeholder section, formerly NMOT)	-	0	-

-
Included w.e.f.09.04.2025

5454

Pulp and Paper Research Institute (PAPRI), Rayagada

5169006

IS 14490 (2024)

Plain Copier Paper â Specification (Second Revision)

Plain copier Paper-Specification

14445 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1(plain copier paper)	-	0	-
5.1.2(k,)	-	0	-
5.2(Moisture)	-	1110	5% to BIS
5.3(Grammage (Substance))	-	1110	5% to BIS
5.4(Thickness)	-	1110	5% to BIS
5.5(Size)	-	510	5% to BIS
5.6, Table 1, i(ISO brightness, percent, Min)	-	1110	5% to BIS
5.6, Table 1, ii(Opacity, percent, Min)	-	1110	5% to BIS
5.6, Table 1, iii(One minute cobb test, both sides, g/m2 , Max)	-	1110	5% to BIS
5.6, Table 1, iv(Surface strength, Dennison (Wax Pick))	-	1725	5% to BIS
5.6, Table 1, v(Smoothness for both sides (Bendsten), ml/min, Max)	-	1110	5% to BIS
5.6, Table 1, vi(Ash content (at 900 °C), percent by mass, Max)	-	1110	5% to BIS
5.6, Table 1, vii(Taber stiffness, Min: Machine direction, Cross direction)	-	1110	5% to BIS
5.6, Table 1, viii(Tear Index, mN.m2 /g, Min: Machine direction, Cross direction)	-	1110	5% to BIS
5.6, Table 1, ix(Tensile index, N.m/g, Min: Machine direction, Cross direction)	-	1110	5% to BIS
5.7(Conditioning specified)	-	0	-
5.1.1(plain copier paper)	-	0	-
5.1.2(k,)	-	0	-
5.2(Moisture)	-	1110	-
5.3(Grammage (Substance))	-	1110	-
5.4(Thickness)	-	1110	-
5.5(Size)	-	510	-
5.6, Table 1, i(ISO brightness, percent, Min)	-	1110	-
5.6, Table 1, ii(Opacity, percent, Min)	-	1110	-
5.6, Table 1, iii(One minute cobb test, both sides, g/m2 , Max)	-	1110	-
5.6, Table 1, iv(Surface strength, Dennison (Wax Pick))	-	1725	-
5.6, Table 1, v(Smoothness for both sides (Bendsten), ml/min, Max)	-	1110	-
5.6, Table 1, vi(Ash content (at 900 °C), percent by mass, Max)	-	1110	-
5.6, Table 1, vii(Taber stiffness, Min: Machine direction, Cross direction)	-	1110	-
5.6, Table 1, viii(Tear Index, mN.m2 /g, Min: Machine direction, Cross direction)	-	1110	-
5.6, Table 1, ix(Tensile index, N.m/g, Min: Machine direction, Cross direction)	-	1110	-
5.7(Conditioning specified)	-	0	-
5.1.1(plain copier paper)	-	-	-
5.1.2(k,)	-	-	-
5.2(Moisture)	-	-	-
5.3(Grammage (Substance))	-	-	-
5.4(Thickness)	-	-	-
5.5(Size)	-	-	-
5.6, Table 1, i(ISO brightness, percent, Min)	-	-	-
5.6, Table 1, ii(Opacity, percent, Min)	-	-	-
5.6, Table 1, iii(One minute cobb test, both sides, g/m2 , Max)	-	-	-
5.6, Table 1, iv(Surface strength, Dennison (Wax Pick))	-	-	-
5.6, Table 1, v(Smoothness for both sides (Bendsten), ml/min, Max)	-	-	-
5.6, Table 1, vi(Ash content (at 900 °C), percent by mass, Max)	-	-	-
5.6, Table 1, vii(Taber stiffness, Min: Machine direction, Cross direction)	-	-	-
5.6, Table 1, viii(Tear Index, mN.m2 /g, Min: Machine direction, Cross direction)	-	-	-
5.6, Table 1, ix(Tensile index, N.m/g, Min: Machine direction, Cross direction)	-	-	-
5.7(Conditioning specified)	-	-	-

13 Oct, 2027

-
Included w.e.f.09.04.2025 Exclusion Cl 5.8 (Additional Requirements for Eco-Mark)

5455

Bharat Test House Pvt. Ltd. 1668 Sonipat

9168306

IS 4992 (2024)

Door Handles for Mortice Locks â Specification (Second Revision)

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-6.1(Fastening Elements and Spindle)	-	1000	-
Cl-6.2, Table-2 (i) a(Axial strength percent)	-	4000	-
Cl-6.2, Table-2 (i) b(Pre-load)	-	4000	-
Cl-6.2, Table-2 (i) c(Permanent deformation)	-	5000	-
Cl-6.3(Safety Requirements)	-	1000	-
Cl-6.4, Table-3 (1) a(Number of cycles)	-	4000	-
Cl-6.4, Table-3 (1) b(Force “P”)	-	4000	-
Cl-6.5(Corrosion Resistance)	-	1000	-
Cl-6.6(Fire Resistance Test)	-	5000	-
Cl-8(Marking)	-	1000	-

-
Included w.e.f.13.05.2025

5456

Bharat Test House Pvt. Ltd. 1668 Sonipat

9168306

IS 4992 (1975)

Specification for door handles for mortice locks (Vertical Type) (First Revision)

19500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 8.1(Finish - Brass door handles shall have natural finish or shall be bright electro chromium plated. Aluminium alloy door handles shall be anodized )	-	3000	-
Cl. 8.1 (Ref. Cl.9 of IS 1868:1996)(Finish - Anodinc casting thickness (Cl. 9.2 of IS 1868:1996))	-	3000	-
4.1(MANUFACTURE AND CONSTRUCTION)	-	1000	-
4.2(MANUFACTURE AND CONSTRUCTION)	-	1000	-
5(DIMENSIONS AND TOLERANCES)	-	1000	-
6.1(Performance Requirments)	-	5000	-
6.2(Performance Requirments)	-	5000	-
7(WORKMANSHIP)	-	1000	-
7(WORKMANSHIP)	-	1000	-
8(FINISH)	-	500	-
8(FINISH)	-	500	-
8(FINISH)	-	500	-

-
Included w.e.f.19.05.2025

5457

Gravitas Laboratories Private Limited, Greater Noida

8182606

IS 11169 : Part 2 (2023)

STEELS FOR COLD HEADING/COLD EXTRUSION APPLICATIONS part 2 stainless steels-SPECIFICATION (first revision)

All size

10500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-7.1(Ladle Analysis)	-	500	-
Cl-7.2, Table-1 (i)(Carbon)	-	500	-
Cl-7.2, Table-1 (ii)(Silicon)	-	500	-
Cl-7.2, Table-1 (iii)(Manganese)	-	500	-
Cl-7.2, Table-1 (iv)(Chromium)	-	500	-
Cl-7.2, Table-1 (v)(Molybdenum)	-	500	-
Cl-7.2, Table-1 (vi)(Nickel)	-	500	-
Cl-7.2, Table-1 (vii)(Sulphur)	-	500	-
Cl-7.2, Table-1 (viii)(Phosphorus)	-	500	-
Cl-7.2, Table-1 (ix)(Titanium)	-	500	-
Cl-7.2, Table-1 (x)(Nitrogen)	-	500	-
Cl-7.2, Table-1 (xi)(Aluminium)	-	500	-
Cl-7.2, Table-1 (xii)(Boron)	-	500	-
Cl-7.2, Table-1 (xiii)(Copper)	-	500	-
Cl-7.2, Table-1 (xiv)(Vanadium)	-	500	-
Cl-8.1,(Mechanical properties)	-	500	-
Cl-10.1(Upsetting Test)	-	500	-
Cl-12(Retests)	-	2000	-
Cl-13.2.1(Tolerances on Bright Bars)	-	500	-
Cl-13.2.1.1(Tolerance Classes)	-	500	-
Cl-13.2.1.1(Width Tolerance for Drawn Flats)	-	500	-
Cl-13.2.3(Straightness Tolerance)	-	500	-
Cl-13.2.4(Out of Shape)	-	500	-
Cl-13.2.5(Edges of Non-Round Bars)	-	500	-
Cl-7.1(Ladle Analysis)	-	0	-
Cl-7.2, Table-1 (i)(Carbon)	-	0	-
Cl-7.2, Table-1 (ii)(Silicon)	-	0	-
Cl-7.2, Table-1 (iii)(Manganese)	-	0	-
Cl-7.2, Table-1 (iv)(Chromium)	-	0	-
Cl-7.2, Table-1 (v)(Molybdenum)	-	0	-
Cl-7.2, Table-1 (vi)(Nickel)	-	0	-
Cl-7.2, Table-1 (vii)(Sulphur)	-	0	-
Cl-7.2, Table-1 (viii)(Phosphorus)	-	0	-
Cl-7.2, Table-1 (ix)(Titanium)	-	0	-
Cl-7.2, Table-1 (x)(Nitrogen)	-	0	-
Cl-7.2, Table-1 (xi)(Aluminium)	-	0	-
Cl-7.2, Table-1 (xii)(Boron)	-	0	-
Cl-7.2, Table-1 (xiii)(Copper)	-	0	-
Cl-7.2, Table-1 (xiv)(Vanadium)	-	0	-
Cl-8.1,(Mechanical properties)	-	0	-
Cl-10.1(Upsetting Test)	-	0	-
Cl-12(Retests)	-	0	-
Cl-13.2.1(Tolerances on Bright Bars)	-	0	-
Cl-13.2.1.1(Tolerance Classes)	-	0	-
Cl-13.2.1.1(Width Tolerance for Drawn Flats)	-	0	-
Cl-13.2.3(Straightness Tolerance)	-	0	-
Cl-13.2.4(Out of Shape)	-	0	-
Cl-13.2.5(Edges of Non-Round Bars)	-	0	-

-
Included w.e.f 22.07.2025 Excluding Cl. 11 Surface Quality

5458

Gravitas Laboratories Private Limited, Greater Noida

8182606

IS 2067 (1975)

Specification for wrought aluminium wire for electrical purposes (Fourth Revision)

All sizes

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause No 4("Chemical Composition")	-	2000	-
Clause No 5.1("Mechanical properties ")	-	1500	-
Clause No 6("Freedom from defects ")	-	500	-
Clause No 7.1(Electrical resistivity of the wire condition o, H3, H4)	-	1500	-
Clause No 8("Mechanical properties condition o, H3, H4")	-	1500	-
Clause No 9(Joints)	-	500	-
Clause No 10.1(Tolerances (on size))	-	500	-
Clause No 12.1(Tensile test)	-	1500	-
Clause No 12.2(Elongation test)	-	1500	-
Clause No 12.3(Wrapping test)	-	1500	-
Clause No 12.4.1(Electrical resistivity shall be measured at room temp.)	-	1500	-
Clause No 4("Chemical Composition")	-	0	-
Clause No 5.1("Mechanical properties ")	-	0	-
Clause No 6("Freedom from defects ")	-	0	-
Clause No 7.1(Electrical resistivity of the wire condition o, H3, H4)	-	0	-
Clause No 8("Mechanical properties condition o, H3, H4")	-	0	-
Clause No 9(Joints)	-	0	-
Clause No 10.1(Tolerances (on size))	-	0	-
Clause No 12.1(Tensile test)	-	0	-
Clause No 12.2(Elongation test)	-	0	-
Clause No 12.3(Wrapping test)	-	0	-
Clause No 12.4.1(Electrical resistivity shall be measured at room temp.)	-	0	-
Clause No 4("Chemical Composition")	-	0	-
Clause No 5.1("Mechanical properties ")	-	0	-
Clause No 6("Freedom from defects ")	-	0	-
Clause No 7.1(Electrical resistivity of the wire condition o, H3, H4)	-	0	-
Clause No 8("Mechanical properties condition o, H3, H4")	-	0	-
Clause No 9(Joints)	-	0	-
Clause No 10.1(Tolerances (on size))	-	0	-
Clause No 12.1(Tensile test)	-	0	-
Clause No 12.2(Elongation test)	-	0	-
Clause No 12.3(Wrapping test)	-	0	-
Clause No 12.4.1(Electrical resistivity shall be measured at room temp.)	-	0	-

-
Included w.e.f 22.07.2025

5459

INDIAN TEST HOUSE PRIVATE LIMITED, MURADNAGAR

8183336

IS 1328 (1996)

Veneered Decorative Plywood -Specification

MR/BWR/Type1/Type2

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Grade - For BWR)	-	0	-
4.1(Grade - For MR)	-	0	-
4.2(Type - For Type 1)	-	0	-
4.2(Type - For Type 2)	-	0	-
7.1.1(Requirements - Open splits, checks or open joints - For Type 1 - Cl. 7.1.1)	-	0	-
7.2.1(Requirements - Open splits, checks or open joints - For Type 2 - Cl. 7.2.1)	-	0	-
7.1.2(Requirements - Other defects - For Type 1 - Cl. 7.1.2)	-	0	-
7.2.2(Requirements - Other defects - For Type 2 - Cl. 7.2.2.)	-	0	-
7.1.3(Requirements - Other Charcteristics and Manufacturing Defects - For Type 1 - Cl. 7.1.3)	-	0	-
7.2.3(Requirements - Other Charcteristics and Manufacturing Defects - For Type 2 - Cl. 7.2.3)	-	0	-
8(Dimensions & Tolerances - Length - Cl. 8)	-	500	-
8(Dimensions & Tolerances - Width - Cl. 8)	-	500	-
8(Dimensions & Tolerances - Thickness - Cl. 8)	-	500	-
8(Dimensions & Tolerances - Edge Straightness - Annexure C)	-	500	-
8(Dimensions & Tolerances - Squareness - Annexure C)	-	500	-
9(Finish - Cl. 9.1, 8.3)	-	1000	-
9(Finish - Cl. 9.2, 8.3)	-	1000	-
11(Tests - Moisture Content - Part 1 of IS 1734)	-	1000	-
11(Tests - Water Resistance Test - Cl. 11.1.2.1 [for MR Grade])	-	1000	-
11(Tests - Water Resistance Test - Cl. 11.1.2.2 [for BWR Grade])	-	1000	-
6.1(Decorative Veneers (Thickness))	-	500	-
4.1(Grade - For BWR)	-	0	-
4.1(Grade - For MR)	-	0	-
4.2(Type - For Type 1)	-	0	-
4.2(Type - For Type 2)	-	0	-
7.1.1(Requirements - Open splits, checks or open joints - For Type 1 - Cl. 7.1.1)	-	0	-
7.2.1(Requirements - Open splits, checks or open joints - For Type 2 - Cl. 7.2.1)	-	0	-
7.1.2(Requirements - Other defects - For Type 1 - Cl. 7.1.2)	-	0	-
7.2.2(Requirements - Other defects - For Type 2 - Cl. 7.2.2.)	-	0	-
7.1.3(Requirements - Other Charcteristics and Manufacturing Defects - For Type 1 - Cl. 7.1.3)	-	0	-
7.2.3(Requirements - Other Charcteristics and Manufacturing Defects - For Type 2 - Cl. 7.2.3)	-	0	-
8(Dimensions & Tolerances - Length - Cl. 8)	-	500	-
8(Dimensions & Tolerances - Width - Cl. 8)	-	500	-
8(Dimensions & Tolerances - Thickness - Cl. 8)	-	500	-
8(Dimensions & Tolerances - Edge Straightness - Annexure C)	-	500	-
8(Dimensions & Tolerances - Squareness - Annexure C)	-	500	-
9(Finish - Cl. 9.1, 8.3)	-	500	-
9(Finish - Cl. 9.2, 8.3)	-	500	-
11(Tests - Moisture Content - Part 1 of IS 1734)	-	500	-
11(Tests - Water Resistance Test - Cl. 11.1.2.1 [for MR Grade])	-	1000	-
11(Tests - Water Resistance Test - Cl. 11.1.2.2 [for BWR Grade])	-	1000	-
6.1(Decorative Veneers (Thickness))	-	500	-

30 Dec, 2027

-
Included w.e.f 05.06.2025

5460

Gravitas Laboratories Private Limited, Greater Noida

8182606

IS 736 (1986)

Specification for wrought aluminium and aluminium alloy plate for general engineering purposes (Third Revision)

All sizes

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Freedom from defect)	-	500	-
5(chemical composition)	-	500	-
6.1 table 2(0.2% proof strength)	-	1500	-
6.1 table 2(tensile strength)	-	1500	-
6.1 table 2(Elongation)	-	1000	-
5.1, Table 1(Aluminium)	-	500	-
5.1, Table 1(Copper)	-	500	-
8(Dimensions & Tolerances)	-	500	-
5.1, Table 1(Magnesium)	-	500	-
5.1, Table 1(Silicon)	-	500	-
5.1, Table 1(Iron)	-	500	-
5.1, Table 1(Mangnese)	-	500	-
5.1, Table 1(Zinc)	-	500	-
5.1, Table 1(Titanium and /or other grain refining element)	-	500	-
5.1, Table 1(Chromium)	-	500	-
5.1, Table 1(Vanadium)	-	500	-
4(Freedom from defect)	-	500	-
5(chemical composition)	-	0	-
6.1 table 2(0.2% proof strength)	-	0	-
6.1 table 2(tensile strength)	-	0	-
6.1 table 2(Elongation)	-	0	-
5.1, Table 1(Aluminium)	-	0	-
5.1, Table 1(Copper)	-	0	-
8(Dimensions & Tolerances)	-	0	-
5.1, Table 1(Magnesium)	-	0	-
5.1, Table 1(Silicon)	-	0	-
5.1, Table 1(Iron)	-	0	-
5.1, Table 1(Mangnese)	-	0	-
5.1, Table 1(Zinc)	-	0	-
5.1, Table 1(Titanium and /or other grain refining element)	-	0	-
5.1, Table 1(Chromium)	-	0	-
5.1, Table 1(Vanadium)	-	0	-

-
Included w.e.f 11.07.2025

Bureau of Indian Standards

The National Standards Body of India

Search by IS Number