BIS - LIMS (Laboratory Information Management System)

Search by IS Number

Reset

15475 Results

S.No.

Lab Name

Osl Code

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

7831

Samridhi Test House Pvt. Ltd.

8184706

IS 17681 (2022)

Specification for Bottled water dispensers

210000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Construction)	-	6300	-
4.1(General Design)	-	700	-
4.2(Materials)	-	700	-
4.3(Finish)	-	700	-
4.4(Thermal Insulation)	-	700	-
4.5(Hardware)	-	700	-
4.6(Disposal of Waste Water)	-	700	-
4.7(Hot Water Tank)	-	700	-
4.8(Hermetically Sealed Compressor)	-	700	-
4.9(Protective Guards)	-	700	-
5(Refrigeration System)	-	1000	-
5.1(Pipes and Connections/Fitting)	-	500	-
5.2(Control of Operation)	-	500	-
6.1(General)	-	30700	-
6.1(Protection against electric shock (Cl. 8 of IS 302-2-24))	-	2000	-
6.1(Power Input & Current (Cl. 10 of IS 302-2-24))	-	3000	-
6.1(Temperature Rise/ Heating (Cl. 11 of IS 302-2-24))	-	5000	-
6.1("Insulation Resistance and Electric Strength/ Leakage Current and Electric Strength (Cl. 13 of IS 302-2-24)")	-	6000	-
6.1("Moisture Resistance (Cl. 15 of IS 302-2-24)")	-	3500	-
6.1("Insulation resistance and electric strength (After humidity treatment) (Cl. 16 of IS 302-2-24)")	-	4000	-
6.1("Provision For Earthing (Cl. 27 of IS 302-2-24)")	-	4000	-
6.2(Electrical Accessories)	-	1500	-
6.3(Salt Mist Test)	-	20000	-
7(Sound pressure level)	-	14300	-
10.1(Cooling Capacity Test)	-	22000	-
10.2(Maximum Operating Condition Test (Environmental))	-	15000	-
10.3(Maximum Operating Condition Test (Voltage))	-	15000	-
10.4(Heating Capacity Test)	-	15000	-
10.5(Annual Energy Consumption Test)	-	30000	-
10.6(Freeze-up Test)	-	20000	-
10.7(Door Opening and Closing Test)	-	8000	-
10.8(Door Seal Test)	-	2000	-
10.9(Pull-down Test)	-	8000	-
11(Marking and instruction)	-	1000	-
6.1("Screws & Connections (Cl. 28 of IS 302-2-24)")	-	3000	-

-
Included w.e.f 21.05.2025

7832

BIS, Northern Regional Laboratory (NRL)

None

IS 2347 (2023)

DOMESTIC PRESSURE COOKER ï¿½ SPECIFICATION

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Gross capacity)	-
4.2 (Body Capacity)	-
6 (Construction)	-
7 (Workmanship and Finish )	-
8.1 (Air Pressure Test )	-
8.2 (Proof Pressure Test )	-
8.6.2 (Tests for Removal of Lid under Pressure For inner Lid Cooker)	-
8.3 (Operating Test for Pressure Regulating Device )	-
8.4 (Test for Safety Relief Device )	-
8.5 (Bursting Pressure Test )	-
8.6.1 (Tests for Removal of Lid under Pressure For Outer Lid Cooker)	-

-
-

7833

ALAIPURIA TEST HOUSE PRIVATE LIMITED, GHAZIABAD

8180426

IS 302 : Part 2 : Sec 14 (2009)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 14 electric kitchen machines (First Revision)

-----

15400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Classification- IS 302-1 )	-	50	-
6(Classification- IS 302-1)	-	50	-
7.1(Marking- IS 302-1)	-	50	-
7.1(Marking- IS 302-1)	-	50	-
7.1(Marking- IS 302-1)	-	50	-
7.1(Marking- IS 302-1)	-	50	-
7.1(Marking- IS 302-1)	-	50	-
7.1(Marking- IS 302-1)	-	50	-
7.1(Marking- IS 302-1)	-	50	-
7.3(Marking- IS 302-1)	-	50	-
7.4(Marking- IS 302-1)	-	50	-
7.6(Marking- IS 302-1)	-	50	-
7.7(Marking- IS 302-1)	-	50	-
7.8(Marking- IS 302-1)	-	50	-
7.11(Marking- IS 302-1)	-	50	-
7.12(Marking- IS 302-1)	-	50	-
7.13(Marking- IS 302-1)	-	50	-
7.14(Marking- IS 302-1)	-	50	-
7.15(Marking- IS 302-1)	-	200	-
7.101(Marking)	-	50	-
8( Protection Against Electric Shock, IS 302-1)	-	500	-
10(Power Input and Current, IS 302-1)	-	1000	-
11(Heating, IS 302-1)	-	500	-
11(Heating, IS 302-1)	-	50	-
11(Heating, IS 302-1)	-	50	-
11(Heating, IS 302-1)	-	50	-
11(Heating, IS 302-1)	-	50	-
13(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-	500	-
13(Electrical Insulation and Leakage Current at Operating Temperature: High Voltage, IS 302-1)	-	50	-
14(Transient Over Voltages, IS 302-1)	-	500	-
15.1(Moisture Resistance, IS 302-1)	-	500	-
15.2(Moisture Resistance, IS 302-1)	-	500	-
15(Moisture Resistance, IS 302-1)	-	50	-
16(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-	1000	-
16(Electrical Insulation and Leakage Current at Operating Temperature: High Voltage, IS 302-1)	-	100	-
17(Overload protection of Transformers and Associated Circuits, IS 302-1)	-	150	-
17(Overload protection of Transformers and Associated Circuits, IS 302-1)	-	50	-
19.7(Abnormal Operation, IS 302-1)	-	500	-
19.8(Abnormal Operation, IS 302-1)	-	50	-
19.9(Abnormal Operation, IS 302-1)	-	50	-
19.1(Abnormal Operation, IS 302-1)	-	50	-
19.101(Abnormal Operation)	-	50	-
19.102(Abnormal Operation)	-	50	-
20.1(Stability & Mechanical Hazards, IS 302-1)	-	500	-
20.2(Stability & Mechanical Hazards, IS 302-1)	-	50	-
20.101(Stability & Mechanical Hazards)	-	50	-
20.102(Stability & Mechanical Hazards)	-	50	-
20.103(Stability & Mechanical Hazards)	-	50	-
20.104(Stability & Mechanical Hazards)	-	50	-
20.105(Stability & Mechanical Hazards)	-	50	-
20.106(Stability & Mechanical Hazards)	-	50	-
20.107(Stability & Mechanical Hazards)	-	50	-
20.108(Stability & Mechanical Hazards)	-	50	-
20.109(Stability & Mechanical Hazards)	-	50	-
20.110(Stability & Mechanical Hazards)	-	50	-
20.111(Stability & Mechanical Hazards)	-	50	-
20.112(Stability & Mechanical Hazards)	-	50	-
20.113(Stability & Mechanical Hazards)	-	50	-
20.114(Stability & Mechanical Hazards)	-	50	-
20.115(Stability & Mechanical Hazards)	-	50	-
20.116(Stability & Mechanical Hazards)	-	50	-
21.1(Mechanical Strength, IS 302-1)	-	500	-
21.2(Mechanical Strength, IS 302-1)	-	50	-
22(Construction, IS 302-1)	-	500	-
22.101(Construction)	-	50	-
22.102(Construction)	-	50	-
23.1(Internal Wiring, IS 302-1)	-	50	-
23.2(Internal Wiring, IS 302-1)	-	50	-
23.3(Internal Wiring, IS 302-1)	-	50	-
23.4(Internal Wiring, IS 302-1)	-	50	-
23.5(Internal Wiring, IS 302-1)	-	50	-
23.6(Internal Wiring, IS 302-1)	-	50	-
23.7(Internal Wiring, IS 302-1)	-	50	-
23.8(Internal Wiring, IS 302-1)	-	50	-
23.9(Internal Wiring, IS 302-1)	-	50	-
23.10(Internal Wiring, IS 302-1)	-	50	-
24.1(Components, IS 302-1)	-	500	-
24.2(Components, IS 302-1)	-	50	-
24.5(Components, IS 302-1)	-	50	-
24.6(Components, IS 302-1)	-	50	-
25.1(Supply Connection and External Flexible Cords, IS 302-1)	-	100	-
25.5(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.6(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.7(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.8(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
26.9(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.1(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.11(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.12(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.13(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.14(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.14(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.15(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.16(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.17(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.18(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.19(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.2(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.21(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.22(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
26(Terminals for External Conductors, IS 302-1)	-	50	-
27(Provision for Earthing, IS 302-1)	-	500	-
27.2(Provision for Earthing, IS 302-1)	-	50	-
27.3(Provision for Earthing, IS 302-1)	-	50	-
27.4(Provision for Earthing, IS 302-1)	-	50	-
27.5(Provision for Earthing, IS 302-1)	-	50	-
28(Screws & Connections, IS 302-1)	-	100	-
29.1(Clearances, Creepage distances and Solid Insulation, IS 302-1)	-	100	-
29.2(Clearances, Creepage distances and Solid Insulation, IS 302-1)	-	50	-
30.1(Resistance to Heat and Fire, IS 302-1)	-	500	-
30.2(Resistance to Heat and Fire, IS 302-1)	-	50	-
31(Resistance of Rusting, IS 302-1)	-	500	-
4(GENERAL REQUIREMENTS)	-	50	-
5(GENERAL CONDITIONS FOR THE TESTS)	-	50	-
27(Provision for Earthing)	-	50	-
29(Clearances, Creepage distances and Solid Insulation)	-	50	-
7.1(Marking- IS 302-1)	-	50	-
6(Classification- IS 302-1 )	-	50	-
6(Classification- IS 302-1)	-	50	-
7.1(Marking- IS 302-1)	-	50	-
7.1(Marking- IS 302-1)	-	50	-
7.1(Marking- IS 302-1)	-	50	-
7.1(Marking- IS 302-1)	-	50	-
7.1(Marking- IS 302-1)	-	50	-
7.1(Marking- IS 302-1)	-	50	-
7.1(Marking- IS 302-1)	-	50	-
7.3(Marking- IS 302-1)	-	50	-
7.4(Marking- IS 302-1)	-	50	-
7.6(Marking- IS 302-1)	-	50	-
7.7(Marking- IS 302-1)	-	50	-
7.8(Marking- IS 302-1)	-	50	-
7.11(Marking- IS 302-1)	-	50	-
7.12(Marking- IS 302-1)	-	50	-
7.13(Marking- IS 302-1)	-	50	-
7.14(Marking- IS 302-1)	-	50	-
7.15(Marking- IS 302-1)	-	200	-
7.101(Marking)	-	50	-
8( Protection Against Electric Shock, IS 302-1)	-	500	-
10(Power Input and Current, IS 302-1)	-	1000	-
11(Heating, IS 302-1)	-	500	-
11(Heating, IS 302-1)	-	50	-
11(Heating, IS 302-1)	-	50	-
11(Heating, IS 302-1)	-	50	-
11(Heating, IS 302-1)	-	50	-
13(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-	500	-
13(Electrical Insulation and Leakage Current at Operating Temperature: High Voltage, IS 302-1)	-	50	-
14(Transient Over Voltages, IS 302-1)	-	500	-
15.1(Moisture Resistance, IS 302-1)	-	500	-
15.2(Moisture Resistance, IS 302-1)	-	500	-
15(Moisture Resistance, IS 302-1)	-	50	-
16(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-	1000	-
16(Electrical Insulation and Leakage Current at Operating Temperature: High Voltage, IS 302-1)	-	100	-
17(Overload protection of Transformers and Associated Circuits, IS 302-1)	-	150	-
17(Overload protection of Transformers and Associated Circuits, IS 302-1)	-	50	-
19.7(Abnormal Operation, IS 302-1)	-	500	-
19.8(Abnormal Operation, IS 302-1)	-	50	-
19.9(Abnormal Operation, IS 302-1)	-	50	-
19.1(Abnormal Operation, IS 302-1)	-	50	-
19.101(Abnormal Operation)	-	50	-
19.102(Abnormal Operation)	-	50	-
20.1(Stability & Mechanical Hazards, IS 302-1)	-	500	-
20.2(Stability & Mechanical Hazards, IS 302-1)	-	50	-
20.101(Stability & Mechanical Hazards)	-	50	-
20.102(Stability & Mechanical Hazards)	-	50	-
20.103(Stability & Mechanical Hazards)	-	50	-
20.104(Stability & Mechanical Hazards)	-	50	-
20.105(Stability & Mechanical Hazards)	-	50	-
20.106(Stability & Mechanical Hazards)	-	50	-
20.107(Stability & Mechanical Hazards)	-	50	-
20.108(Stability & Mechanical Hazards)	-	50	-
20.109(Stability & Mechanical Hazards)	-	50	-
20.110(Stability & Mechanical Hazards)	-	50	-
20.111(Stability & Mechanical Hazards)	-	50	-
20.112(Stability & Mechanical Hazards)	-	50	-
20.113(Stability & Mechanical Hazards)	-	50	-
20.114(Stability & Mechanical Hazards)	-	50	-
20.115(Stability & Mechanical Hazards)	-	50	-
20.116(Stability & Mechanical Hazards)	-	50	-
21.1(Mechanical Strength, IS 302-1)	-	500	-
21.2(Mechanical Strength, IS 302-1)	-	50	-
22(Construction, IS 302-1)	-	500	-
22.101(Construction)	-	50	-
22.102(Construction)	-	50	-
23.1(Internal Wiring, IS 302-1)	-	50	-
23.2(Internal Wiring, IS 302-1)	-	50	-
23.3(Internal Wiring, IS 302-1)	-	50	-
23.4(Internal Wiring, IS 302-1)	-	50	-
23.5(Internal Wiring, IS 302-1)	-	50	-
23.6(Internal Wiring, IS 302-1)	-	50	-
23.7(Internal Wiring, IS 302-1)	-	50	-
23.8(Internal Wiring, IS 302-1)	-	50	-
23.9(Internal Wiring, IS 302-1)	-	50	-
23.10(Internal Wiring, IS 302-1)	-	50	-
24.1(Components, IS 302-1)	-	500	-
24.2(Components, IS 302-1)	-	50	-
24.5(Components, IS 302-1)	-	50	-
24.6(Components, IS 302-1)	-	50	-
25.1(Supply Connection and External Flexible Cords, IS 302-1)	-	100	-
25.5(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.6(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.7(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.8(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
26.9(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.1(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.11(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.12(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.13(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.14(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.14(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.15(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.16(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.17(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.18(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.19(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.2(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.21(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.22(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
26(Terminals for External Conductors, IS 302-1)	-	50	-
27(Provision for Earthing, IS 302-1)	-	500	-
27.2(Provision for Earthing, IS 302-1)	-	50	-
27.3(Provision for Earthing, IS 302-1)	-	50	-
27.4(Provision for Earthing, IS 302-1)	-	50	-
27.5(Provision for Earthing, IS 302-1)	-	50	-
28(Screws & Connections, IS 302-1)	-	100	-
29.1(Clearances, Creepage distances and Solid Insulation, IS 302-1)	-	100	-
29.2(Clearances, Creepage distances and Solid Insulation, IS 302-1)	-	50	-
30.1(Resistance to Heat and Fire, IS 302-1)	-	500	-
30.2(Resistance to Heat and Fire, IS 302-1)	-	50	-
31(Resistance of Rusting, IS 302-1)	-	500	-
4(GENERAL REQUIREMENTS)	-	50	-
5(GENERAL CONDITIONS FOR THE TESTS)	-	50	-
27(Provision for Earthing)	-	50	-
29(Clearances, Creepage distances and Solid Insulation)	-	50	-
7.1(Marking- IS 302-1)	-	50	-

03 Oct, 2027

-
Included w.e.f.18.11.2024 Exclusion 32 (Radiation, Toxicity and similar Hazard IS 302-1) 19.11.4.1 to 19.11.4.5 (EMI/EMC)

7834

Ahmedabad Textile Industry's Research Association (ATIRA), Ahmedabad

7173002

IS 17730 : Part 2 (2021)

Agro-Textiles Hail Protection Nets for Agriculture and Horticulture Purposes Specification Part 2 Woven Hail Protection Nets

38170 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 7, Table 1, (i)(Mass in g/m2, (with a tolerance of ± 5 percent))	-	400	-
Clause 7, table 1, (ii) a("Average breaking strength of Woven hail protection fabric (Strip method, 325 × 50 mm test piece with gauge length of 200 mm), N,Min,(a) Warpway")	-	900	-
Clause 7,table 1, (ii) b("Average breaking strength of woven hail protection fabric (Strip method, 325 × 50 mm test piece with gauge length of 200 mm), N,Min,(b) Weftway")	-	0	-
Clause 7, table 1, (iii)("Retention of breaking strength after UV exposure of 144 hours, percent, Min")	-	13860	-
Clause 7,table 1, (iv)(Colour fastness to artificial light (Applicable for coloured hail protection nets only))	-	3300	-
Clause 7, table 1, (v)(Bursting pressure, kgf/cm2, Min)	-	800	-
Clause 7, table 1, (vii)(Porosity, percent)	-	300	-
Clause 7, table 1, (viii)(Cold cracking resistance test at –10 °C)	-	0	-
Clause 7, table 1, (ix)(Seam (joint) strength, percent, Min)	-	800	-
7.1(Dimensions)	-	300	-
Cl-4.1(HDPE Monofilament)	-	450	-
Cl-4.1.1(The heat shrinkage of the monofilament yarn)	-	2000	-
Cl-6.1(Fabric)	-	400	-
Cl-6.2(Reinforcement)	-	200	-
Cl-6.3(Joints)	-	200	-
Cl-6.4(Stitching)	-	13760	-
Cl-6.5(Colour)	-	200	-
Cl-7.1(Dimensions)	-	300	-
Clause 7, Table 1, (i)(Mass in g/m2, (with a tolerance of ± 5 percent))	-	0	-
Clause 7, table 1, (ii) a("Average breaking strength of Woven hail protection fabric (Strip method, 325 × 50 mm test piece with gauge length of 200 mm), N,Min,(a) Warpway")	-	0	-
Clause 7,table 1, (ii) b("Average breaking strength of woven hail protection fabric (Strip method, 325 × 50 mm test piece with gauge length of 200 mm), N,Min,(b) Weftway")	-	0	-
Clause 7, table 1, (iii)("Retention of breaking strength after UV exposure of 144 hours, percent, Min")	-	0	-
Clause 7,table 1, (iv)(Colour fastness to artificial light (Applicable for coloured hail protection nets only))	-	0	-
Clause 7, table 1, (v)(Bursting pressure, kgf/cm2, Min)	-	0	-
Clause 7, table 1, (vii)(Porosity, percent)	-	0	-
Clause 7, table 1, (viii)(Cold cracking resistance test at –10 °C)	-	0	-
Clause 7, table 1, (ix)(Seam (joint) strength, percent, Min)	-	0	-
7.1(Dimensions)	-	0	-
Cl-4.1(HDPE Monofilament)	-	0	-
Cl-4.1.1(The heat shrinkage of the monofilament yarn)	-	0	-
Cl-6.1(Fabric)	-	0	-
Cl-6.2(Reinforcement)	-	0	-
Cl-6.3(Joints)	-	0	-
Cl-6.4(Stitching)	-	0	-
Cl-6.5(Colour)	-	0	-
Cl-7.1(Dimensions)	-	0	-
Clause 7, Table 1, (i)(Mass in g/m2, (with a tolerance of ± 5 percent))	-	0	-
Clause 7, table 1, (ii) a("Average breaking strength of Woven hail protection fabric (Strip method, 325 × 50 mm test piece with gauge length of 200 mm), N,Min,(a) Warpway")	-	0	-
Clause 7,table 1, (ii) b("Average breaking strength of woven hail protection fabric (Strip method, 325 × 50 mm test piece with gauge length of 200 mm), N,Min,(b) Weftway")	-	0	-
Clause 7, table 1, (iii)("Retention of breaking strength after UV exposure of 144 hours, percent, Min")	-	0	-
Clause 7,table 1, (iv)(Colour fastness to artificial light (Applicable for coloured hail protection nets only))	-	0	-
Clause 7, table 1, (v)(Bursting pressure, kgf/cm2, Min)	-	0	-
Clause 7, table 1, (vii)(Porosity, percent)	-	0	-
Clause 7, table 1, (ix)(Seam (joint) strength, percent, Min)	-	0	-
7.1(Dimensions)	-	0	-
Cl-4.1(HDPE Monofilament)	-	0	-
Cl-4.1.1(The heat shrinkage of the monofilament yarn)	-	0	-
Cl-6.1(Fabric)	-	0	-
Cl-6.2(Reinforcement)	-	0	-
Cl-6.3(Joints)	-	0	-
Cl-6.4(Stitching)	-	0	-
Cl-6.5(Colour)	-	0	-
Cl-7.1(Dimensions)	-	0	-

-
Included w.e.f 12.03.2025 Exclusion: Clause 7, table 1, (vi) (Shading percentage, percent, Max) Clause 7, table 1, (viii) (Cold cracking resistance test at –10 °C)

7835

ALAIPURIA TEST HOUSE PRIVATE LIMITED, GHAZIABAD

8180426

IS 302 : Part 2 : Sec 23 (2009)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 23 appliances for skin or hair care (First Revision)

-----

22000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
31(Resistance to Rusting)	-	1000	-
30(Resistance to Heat & Fire)	-	1000	-
29(Clearances, Creepage Distances & Solid Insulation)	-	1500	-
28(Screws & Connection)	-	500	-
27(Provision For Earthing)	-	1500	-
26(Terminals For External Conductors)	-	500	-
25(Supply Connection & External Flexible Cables and Cords)	-	500	-
24(Component)	-	500	-
23(Internal wiring)	-	500	-
22(Construction)	-	500	-
21(Mechanical strength)	-	500	-
20(Stability & Mechanical Hazards)	-	500	-
19(Abnormal Operation)	-	1500	-
18(Endurance)	-	500	-
17(Overload Protection/ Overload Protection of Transformers & Associated Circuits)	-	500	-
16(Leakage Current and Electric Strength)	-	1000	-
15(Moisture Resistance)	-	1000	-
14(Transient Over Voltage)	-	1000	-
13(Leakage Current and Electric Strength at Operating Temperature)	-	1000	-
11(Temperature Rise/Heating)	-	1500	-
10(Power Input & Current)	-	2500	-
9(Starting Of Motor Operated Appliances)	-	500	-
8(Protection against Electric Shock/ Protection against Access to Live Parts)	-	500	-
7(Marking/ Marking & Instructions)	-	500	-
6(Classification)	-	500	-
22.32(CONSTRUCTION)	-	500	-

03 Oct, 2027

-
Included.w.e.f.07.11.2024 Exclusion 32 (RADIATION, TOXICITY AND SIMILAR HAZARDS) 19.11.4.1 to 19.11.4.5 (EMI/EMC)

7836

BIS, Hyderabad Branch Laboratory (HYBL)

None

IS 15351 (2015)

Agro textiles – Laminated high density polyethylene (HDPE) woven geomembrane for water proof lining – Specification (second revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (HDPE Tapes)	-
3.2 (HDPE Fabric)	-
5 (MANUFACTURE)	-
5.1 (Lamination)	-
5.2 (Panel Width)	-
5.3 (Joints/Seams)	-
5.1.1 and 6.2 (Thickness, mm- IS 7016: Part 1)	-
5.1.1 and 6.2 (Mass, g/sq m)	-
5.1.1 and 6.2 (Dimensions, mm- Annexure A of IS 11652)	-
5.1.1 and 6.2 (Length)	-
5.1.1 and 6.2 (Width)	-
5.1.1 and 6.2 (Carbon black content, Percent- IS 2530)	-
5.1.1 and 6.2 (Breaking Load on 20 cm X 10 cm Strip, Min )	-
5.1.1 and 6.2 (Before UV exposure IS 13162 (Part 5)	-
5.1.1 and 6.2 (Strain at Maximum load, Percent-IS 13162 (Part 5)	-
5.1.1 and 6.2 (Impact failure load, at 1524 mm drop,)	-
5.1.1 and 6.2 (Tear resistance, N, Min-Method A1 of IS 7016 (Part 3))	-
5.1.1 and 6.2 (Puncture resistance, N, Min-Annex D)	-
5.1.1 and 6.2 (Bursting strength (Ball burst),N/cm², Min-)	-
5.1.1 and 6.2 (Seam strength before UV exposure (N/mm), Min-IS 15060)	-
5.1.1 and 6.2 (Hydrostatic resistance-Annex E)	-
5.1.1 and 6.2 (Ash content, percent, Max-Annex F)	-

-
except long term tests.

7837

BIS, Hyderabad Branch Laboratory (HYBL)

None

IS 14887 (2014)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg food grains – Specification (first revision)

19750 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2 (Tapes – Width and Thickness ( IS 6192/IS 11197))	-
3.2 (Tapes – Linear Density (IS 6192/IS 11197))	-
3.3.1 (Bottom seam (IS 10789))	-
4.1 and 3.4 (Mass of bale (Cl. 4.1), Capacity (Cl 3.4))	-
4.2 and Table 1 ii (Dimensions )	-
5.2 and Table 1 iii (Ends per dm )	-
5.2 and Table 1 iv (Picks per dm )	-
4.2 and Table 1 v (Mass of sack )	-
4.2 and Table 1 vi (Average breaking strength of fabric )	-
4.2 and Table 1 vi (Breaking strength of bottom seam )	-
4.2 and Table 1 viii (Elongation at break of fabric )	-
4.2 and Table 1 ix (Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-
4.2 and Table 1 x (Ash content )	-

-
Complete test facility

7838

BIS, Hyderabad Branch Laboratory (HYBL)

None

IS 14968 (2015)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packing 50 Kg/25 kg sugar – Specification (first revision)

14300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3 (TYPES)	-
4.1 (Raw Material)	-
4.2 (Tapes – Width IS 6192 and IS 11197)	-
4.2 (Tapes – Linear Density )	-
4.3 (Sacks)	-
4.3.1 (Bottom Seam)	-
4.3.1 (The two rows of stitches shall be separated from each other)	-
4.3.1 ( The outer stitch)	-
4.3.1 ( The stitching shall be done with double fold over seam to a depth )	-
4.3.1 (Stitches pass through a minimum of six layers of the fabric. )	-
4.3.1 (stitches/dm)	-
4.3.2 (Mouth)	-
4.4 (Liner IS 10146 or IS 10910.)	-
4.4 (Mass of the loose liner )	-
4.4 (Width of the loose liner)	-
4.4 (Length of the line)	-
4.4 (Bottom seam of the loose liner)	-
4.4.1 (Liner)	-
4.5 and Table 1 i (Capacity)	-
5.2 and Table 1 ii a (Dimensions Inside Length)	-
5.2 and Table 1 ii b (Dimensions Inside Width)	-
5.2 and Table 1 iii (Ends per dm )	-
5.2 and Table 1 iv (Picks per dm )	-
5.1 and Table 1 v a (Mass of unlaminated sack IS 1964)	-
5.1 and Table 1 v b (Mass of unlaminated sack with liner )	-
5.2 and Table 1 vi a (Average breaking strength of fabric Lengthwise IS 1969 (Part 1))	-
5.2 and Table 1 vi b (Average breaking strength of fabric Widthwise IS 1969 (Part 1))	-
5.2 and Table 1 vi (Breaking strength of bottom seam IS 9030 )	-
5.2 and Table 1 viii a (Elongation at break of fabric Lengthwise IS 1969 (Part 1))	-
5.2 and Table 1 viii b (Elongation at break of fabric Widthwise IS 1969 (Part 1))	-
5.2 and Table 1 ix (Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-
5.2 and Table 1 x (Ash content )	-

-
Complete test facility

7839

Bombay Textiles Research Association (BTRA), Mumbai

7130206

IS 16393 (2015)

Geosynthetics - Geotextiles used in subsurface drainage application - Specification

219560 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
1(Roll length- IS 1954)	-	500	-
1(Roll width- IS 1954)	-	500	-
1(Grab strength- IS 16342)	-	1500	-
1(Sewn seam strength- IS 15060)	-	1500	-
1(Trapezidal tear strength- IS 14293)	-	1500	-
1(CBR puncture strength- IS 16078)	-	2700	-
1(Burst strength- IS 1966 (part-2))	-	1500	-
1(Permitttivity- IS 14324)	-	2100	-
1(Apparent opening size (AOS)- IS 14294)	-	750	-
1("Resistance to installation damage, Percent retained strength- ISO 10722 SC SW GP")	-	150000	-
1("Ultraviolet stability at 500h, Retained strength- IS 13162 (part-2)")	-	52000	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation <50%(Type of geotextile)	-	500	-
4.2(Polyster)	-	760	-
4.2(carbon black content and dispersion)	-	750	-
4.2(isophthalic acid content)	-	3000	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation <50%(Roll length)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation <50%(Roll width)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation <50%(Grab strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation <50%(Sewn seam strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation <50%(Trapezidal tear strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation <50%(CBR puncture strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation <50%(Burst strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation <50%(Permitttivity, sec-1)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation <50%(Apparent opening size (AOS), mm)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation <50%(Resistance to installation damage, percent retained strength, SC/SW/GP)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation <50%(Ultraviolet stability at 500 h, retained strength, percent of original strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation <50%(Type of geotextile)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation <50%(Roll length)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation <50%(Roll width)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation <50%(Grab strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation <50%(Sewn seam strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation <50%(Trapezidal tear strength IS 14293)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation <50%(CBR puncture strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation <50%(Burst strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation <50%(Permitttivity, sec-1)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation <50%(Apparent opening size (AOS), mm)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation <50%(Resistance to installation damage, percent retained strength, SC/SW/GP)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation <50%(Ultraviolet stability at 500 h, retained strength, percent of original strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Type of geotextile)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Roll length)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Roll width)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Grab strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Sewn seam strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Trapezidal tear strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Trapezidal tear strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(CBR puncture strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Burst strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Permitttivity, sec-1)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Apparent opening size (AOS), mm)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Resistance to installation damage, percent retained strength, SC/SW/GP)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation <50%(Ultraviolet stability at 500 h, retained strength, percent of original strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Type of geotextile)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Roll length)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Roll width)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Grab strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Sewn seam strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Trapezidal tear strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(CBR puncture strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Burst strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Permitttivity, sec-1)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Apparent opening size (AOS), mm)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Resistance to installation damage, percent retained strength, SC/SW/GP)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation ≥50%(Type of geotextile)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation ≥50%(Roll length)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation ≥50%(Roll width)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation ≥50%(Grab strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation ≥50%(Sewn seam strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation ≥50%(Trapezidal tear strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation ≥50%(CBR puncture strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation ≥50%(Burst strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation ≥50%(Permitttivity, sec-1)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation ≥50%(Apparent opening size (AOS), mm)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation ≥50%(Resistance to installation damage, percent retained strength, SC/SW/GP)	-	0	-
4.3(Roll length)	-	0	-
4.3, table 1, A(ii)(Roll length,m,min)	-	0	-
4.3, table 1, A(ii)(Roll length,m,min)	-	0	-
4.3, table 1,A(iii)(Roll width,m,mim)	-	0	-
4.3, table 1,A (iv)(Grab strength,N,Min)	-	0	-
4.3, table 1,A (v)(Sewn seam strength,N,Min)	-	0	-
4.3, table 1,A(vi)(Trapezidal tear strength,N,min)	-	0	-
4.3, table 1,A (vii)(CBR puncture strength,N,Min)	-	0	-
4.3, table 1,A (viii)(Burst strength, kPa, Min)	-	0	-
4.3, table 1,B (ii)(Permitttivity, sec-1, Min)	-	0	-
4.3, table 1,B (iii)(Apparent opening size (AOS), mm, Max)	-	0	-
4.3, table 1,C(iii)(Resistance to installation damage)	-	0	-
4.3, table 1,C (iv)(Ultraviolet stability)	-	0	-
1(Roll length- IS 1954)	-	0	-
1(Roll width- IS 1954)	-	0	-
1(Grab strength- IS 16342)	-	0	-
1(Sewn seam strength- IS 15060)	-	0	-
1(Trapezidal tear strength- IS 14293)	-	0	-
1(CBR puncture strength- IS 16078)	-	0	-
1(Burst strength- IS 1966 (part-2))	-	0	-
1(Permitttivity- IS 14324)	-	0	-
1(Apparent opening size (AOS)- IS 14294)	-	0	-
1("Resistance to installation damage, Percent retained strength- ISO 10722 SC SW GP")	-	0	-
1("Ultraviolet stability at 500h, Retained strength- IS 13162 (part-2)")	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation <50%(Type of geotextile)	-	0	-
4.2(Polyster)	-	0	-
4.2(carbon black content and dispersion)	-	0	-
4.2(isophthalic acid content)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation <50%(Roll length)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation <50%(Roll width)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation <50%(Grab strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation <50%(Sewn seam strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation <50%(Trapezidal tear strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation <50%(CBR puncture strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation <50%(Burst strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation <50%(Permitttivity, sec-1)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation <50%(Apparent opening size (AOS), mm)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation <50%(Resistance to installation damage, percent retained strength, SC/SW/GP)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation <50%(Ultraviolet stability at 500 h, retained strength, percent of original strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation <50%(Type of geotextile)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation <50%(Roll length)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation <50%(Roll width)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation <50%(Grab strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation <50%(Sewn seam strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation <50%(Trapezidal tear strength IS 14293)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation <50%(CBR puncture strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation <50%(Burst strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation <50%(Permitttivity, sec-1)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation <50%(Apparent opening size (AOS), mm)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation <50%(Resistance to installation damage, percent retained strength, SC/SW/GP)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation <50%(Ultraviolet stability at 500 h, retained strength, percent of original strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Type of geotextile)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Roll length)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Roll width)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Grab strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Sewn seam strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Trapezidal tear strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Trapezidal tear strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(CBR puncture strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Burst strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Permitttivity, sec-1)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Apparent opening size (AOS), mm)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Resistance to installation damage, percent retained strength, SC/SW/GP)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation <50%(Ultraviolet stability at 500 h, retained strength, percent of original strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Type of geotextile)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Roll length)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Roll width)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Grab strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Sewn seam strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Trapezidal tear strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(CBR puncture strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Burst strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Permitttivity, sec-1)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Apparent opening size (AOS), mm)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class I, Elongation ≥50%(Resistance to installation damage, percent retained strength, SC/SW/GP)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation ≥50%(Type of geotextile)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation ≥50%(Roll length)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation ≥50%(Roll width)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation ≥50%(Grab strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation ≥50%(Sewn seam strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation ≥50%(Trapezidal tear strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation ≥50%(CBR puncture strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation ≥50%(Burst strength)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation ≥50%(Permitttivity, sec-1)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation ≥50%(Apparent opening size (AOS), mm)	-	0	-
Table 1, Clauses 4.3 and 5.4, Class II, Elongation ≥50%(Resistance to installation damage, percent retained strength, SC/SW/GP)	-	0	-
4.3(Roll length)	-	0	-
4.3, table 1, A(ii)(Roll length,m,min)	-	0	-
4.3, table 1, A(ii)(Roll length,m,min)	-	0	-
4.3, table 1,A(iii)(Roll width,m,mim)	-	0	-
4.3, table 1,A (iv)(Grab strength,N,Min)	-	0	-
4.3, table 1,A (v)(Sewn seam strength,N,Min)	-	0	-
4.3, table 1,A(vi)(Trapezidal tear strength,N,min)	-	0	-
4.3, table 1,A (vii)(CBR puncture strength,N,Min)	-	0	-
4.3, table 1,A (viii)(Burst strength, kPa, Min)	-	0	-
4.3, table 1,B (ii)(Permitttivity, sec-1, Min)	-	0	-
4.3, table 1,B (iii)(Apparent opening size (AOS), mm, Max)	-	0	-
4.3, table 1,C(iii)(Resistance to installation damage)	-	0	-
4.3, table 1,C (iv)(Ultraviolet stability)	-	0	-

-
Included .w.e.f.13.02.2025

7840

CIPET, Lucknow

9102534

IS 14333 (2022)

Polyethylene Pipes for Sewerage and Industrial Chemicals and Effluent ï¿½ Specification (First Revision)

31569 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2.1,T2("Base Density (At 27°C Temp.)-IS 7328:2020 ")	-	700	-
5.2.1,T2(Melt Flow Rate (At 190°C /5kg)-IS 2530:1963)	-	1100	-
5.2.1,T2(Thermal Stability(Oxidation Induction Time)-IS 4984:2016(Annexure-B))	-	2000	-
5.2.1,T2("Volatile Matter- IS 4984:2016 (Annexure-C)")	-	1100	-
5.2.1,T2("Water Content-IS 4984:2016 (Annexure-D)")	-	1100	-
5.2.1.1, T2(Compound Density-IS 7328:2020)	-	700	-
5.2.1.1, T2("Compound carbon black -IS 2530:1963 content")	-	925	-
5.2.1.1, T2(Compound maximum volatile matter -IS 4984:2016 (Annexure-C))	-	1100	-
5.2.1.1, T2(Compound ash content - Any Method)	-	1200	-
5.2.1.1, T2("Compound carbon black -IS 2530:1963 dispersion")	-	925	-
5.3(Density of Higher olefin - IS 7328:2020)	-	700	-
5.3(Olefin Constituents- 14333-2022)	-	500	-
5.3(Loading of Carbon Black - IS 2530:1963)	-	925	-
5.3(Ash content- Any Method)	-	1200	-
5.3("Maximum volatile matter -IS 4984:2016 (Annexure-C)")	-	1100	-
6(Pipe Description - IS 14333-2022)	-	500	-
6.2(Colour- IS 14333-2022)	-	500	-
7.1(Visual Appearance- IS 14333-2022)	-	500	-
7.2(Length- IS 14333-2022)	-	500	-
7.3(Coiling- IS 14333-2022)	-	500	-
7.4,T3 of IS 4984(Outside Diameter-IS 4984-2016)	-	500	-
7.4,T4 of IS 4984(wall Thickness-IS 4984-2016)	-	500	-
7.4,T3 of IS 4984(Ovality-IS 4984-2016)	-	500	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 27 oC , Test Period - 100 hrs.-IS 4984-2016 (Annexure-E))	-	4000	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 48 hrs.-IS 4984-2016 (Annexure-E))	-	1600	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 165 hrs.-IS 4984-2016 (Annexure-E))	-	4800	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 1000 hrs.-IS 4984-2016 (Annexure-E))	-	11000	-
8.1.2, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 48 hrs.-IS 4984-2016 (Annexure-E))	-	1600	-
8.2("Longitudinal Reversion Test - IS 4984-2016 (Annexure-F)")	-	1200	-
8.3(Carbon black content- IS 2530-1963)	-	925	-
8.3(Carbon black content Dispersion- IS 2530-1963)	-	700	-
8.4(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	1100	-
8.6(Density-IS 7328:2020)	-	700	-
8.7("Tensile Strength for Butt Fusion - IS 4984-2016 (Annexure-G)")	-	1800	-
8.8,T5("Tensile - IS 4984-2016 (Annexure-H)")	-	1800	-
8.8,T5("Elongation -IS 4984-2016 (Annexure-H)")	-	0	-
8.9(Slow Crack Growth Rate{Internal Pressure creep Rupture test, Temperature - 80±1 oC , Test Pressure – 0.80MPa, Test Period - 500 hrs.-IS 4984-2016 (Annexure-E &J))	-	6000	-
8.5(Oxidation Induction Time -IS 4984:2016(Annexure-B))	-	2000	-

31 Dec, 2026

-
Included w.e.f. 06.11.2024 Exclusion: Cl.5.2.1.1, T2 (Compound Toluene extract - Any Method), Cl.5.3 (Toluene extract - Any Method), Cl. 5.4 (Antioxidant - Any Method)

7841

URS PRODUCTS AND TESTING PVT. LTD. (A29), NOIDA

8168906

IS 10322 : Part 5 : Sec 1 (2012)

Luminaires: Part 5 particular requirements: Sec 1 fixed general purpose luminaires (First Revision)

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(General Test Requireements)	-	2000	-
5(Classification of Luminaires')	-	3000	-
6.0(Marking)	-	3000	-
7.0(Construction)	-	4000	-
8.0(Creepage Distance and Clearances)	-	2000	-
9.0(Provision for earthing)	-	5000	-
10.0(Terminals)	-	3000	-
11.0(External & Internal Wiring)	-	4000	-
12.0(Protection against electric shock)	-	4000	-
13.0(Endurance Tests and Thermal Tests)	-	6000	-
14.0(Resistance to Dust & Moisture)	-	5000	-
15.0(Insulation Resistance and Electric Strength)	-	4000	-
16.0(Resistance to Heat , fire and tracking)	-	4000	-
17.0(Photometric Test)	-	6000	-
(Cl.4.24) (Annex-P)(UV Radiations for metal halide lamps)	-	2000	-
4.26.2(Short Circuit Protection)	-	2000	-

-
Included w.e.f.26.11.2024 Exclusion (Cl.4.24) (Annex-P) (UV Radiations for metal halide lamps) 4.26.2 (Short Circuit Protection)

7842

IDMA LABORATORIES LIMITED, PANCHKULA

9123236

IS 266 (2024)

Sulphuric Acid âSpecification (Fourth Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1, 4.1.1(Technical Grade (Description))	-	800	Testing Charges 1) Battery Grade (Conc.) INR 15000 2) Battery Grade (Dil.) INR 14000 3) AR Grade INR 10000 4) Chemically Pure Grade INR 9000 5) Technical Grade INR 6000
4.1, 4.1.2(Battery Grade (Concentrated) (Description))	-	800	-
4.1, 4.1.2(Battery Grade (Dilute) (Description))	-	800	-
4.1, 4.1.3(Chemically Pure Grade (Description))	-	800	-
4.1, 4.1.3(Analytical Reagent Grade (Description))	-	800	-
4.3.1 & Table 1, S.No (i)("Total acidity (as H2SO4) (Technical Grade)")	-	1200	-
4.3.1 & Table 1, S.No (ii)("Residue on ignition (Technical Grade)")	-	1000	-
4.3.1 & Table 1, S.No (iii)("Iron (as Fe) (Technical Grade)")	-	1000	-
4.3.1 & Table 1, S.No (v)("Heavy metals (as lead) (Technical Grade)")	-	1000	-
4.3.1 & Table 1, S.No (vi)("Arsenic (as As) (Technical Grade)")	-	1000	-
4.3.2 & Table 1, S.No (i)("Total acidity (as H2SO4) (Battery Grade Concentrated)")	-	1200	-
4.3.2 & Table 1, S.No (ii)("Residue on ignition (Battery Grade Concentrated)")	-	1000	-
4.3.2 & Table 1, S.No (iii)("Iron (as Fe) (Battery Grade Concentrated)")	-	1000	-
4.3.2 & Table 1, S.No (iv)("Chloride (Battery Grade Concentrated)")	-	1000	-
4.3.2 & Table 1, S.No (vi)("Arsenic (as As) (Battery Grade Concentrated)")	-	1000	-
4.3.2 & Table 1, S.No (vii)("Oxidizable impurities (as SO2), (Battery Grade Concentrated)")	-	1000	-
4.3.2 & Table 1, S.No (viii)("Organic Matter (Battery Grade Concentrated)")	-	1000	-
4.3.2 & Table 1, S.No (xi)("Selenium (as Se) (Battery Grade Concentrated)")	-	1000	-
4.3.2 & Table 1, S.No (xii)("Manganese (as Mn) (Battery Grade Concentrated)")	-	1000	-
4.3.2 & Table 1, S.No (xiii)("Copper (as Cu) (Battery Grade Concentrated)")	-	1000	-
4.3.2 & Table 1, S.No (xiv)("Zinc (as Zn) (Battery Grade Concentrated)")	-	1000	-
4.3.2 & Table 1, S.No (xv)("Nitrates, nitrites and ammonia (as N) (Battery Grade Concentrated)")	-	1000	-
4.3.2 & Table 1, S.No (i)("Total acidity (as H2SO4) (Battery Grade Diluted)")	-	1200	-
4.3.2 & Table 1, S.No (ii)("Residue on ignition (Battery Grade Diluted)")	-	1000	-
4.3.2 & Table 1, S.No (iii)("Iron (as Fe) (Battery Grade Diluted)")	-	1000	-
4.3.2 & Table 1, S.No (iv)("Chloride (Battery Grade Diluted)")	-	1000	-
4.3.2 & Table 1, S.No (vi)("Arsenic (as As) (Battery Grade Diluted)")	-	1000	-
4.3.2 & Table 1, S.No (vii)("Oxidizable impurities (as SO2), (Battery Grade Diluted)")	-	1000	-
4.3.2 & Table 1, S.No (xi)("Selenium (as Se) (Battery Grade Diluted)")	-	1000	-
4.3.2 & Table 1, S.No (xii)("Manganese (as Mn) (Battery Grade Diluted)")	-	1000	-
4.3.2 & Table 1, S.No (xiii)("Copper (as Cu) (Battery Grade Diluted)")	-	1000	-
4.3.2 & Table 1, S.No (xiv)("Zinc (as Zn) (Battery Grade Diluted)")	-	1000	-
4.3.2 & Table 1, S.No (xv)("Nitrates, nitrites and ammonia (as N) (Battery Grade Diluted)")	-	1000	-
4.1.3 & Table 1, S.No (i)("Total acidity (as H2SO4) (Chemically Pure Grade)")	-	1200	-
4.1.3 & Table 1, S.No (ii)("Residue on ignition (Chemically Pure Grade)")	-	1000	-
4.1.3 & Table 1, S.No (iii)("Iron (as Fe) (Chemically Pure Grade)")	-	1000	-
4.1.3 & Table 1, S.No (iv)("Chloride (Chemically Pure Grade)")	-	1000	-
4.1.3 & Table 1, S.No (v)("Heavy metals (as lead) (Chemically Pure Grade)")	-	1000	-
4.1.3 & Table 1, S.No (vi)("Arsenic (as As) (Chemically Pure Grade)")	-	1000	-
4.1.3 & Table 1, S.No (vii)("Oxidizable impurities (as SO2), (Chemically Pure Grade)")	-	1000	-
4.1.3 & Table 1, S.No (xv)("Nitrates, nitrites and ammonia (as N) (Chemically Pure Grade)")	-	1000	-
4.1.3 & Table 1, S.No (i)("Total acidity (as H2SO4) (Analytical Reagent Grade)")	-	1200	-
4.1.3 & Table 1, S.No (ii)("Residue on ignition (Analytical Reagent Grade)")	-	1000	-
4.1.3 & Table 1, S.No (iii)("Iron (as Fe) (Analytical Reagent Grade)")	-	1000	-
4.1.3 & Table 1, S.No (iv)("Chloride (Analytical Reagent Grade)")	-	1000	-
4.1.3 & Table 1, S.No (v)("Heavy metals (as lead) (Analytical Reagent Grade)")	-	1000	-
4.1.3 & Table 1, S.No (vi)("Arsenic (as As) (Analytical Reagent Grade)")	-	1000	-
4.1.3 & Table 1, S.No (vi)("Arsenic (as As) (Analytical Reagent Grade)")	-	1000	-
4.1.3 & Table 1, S.No (vii)("Oxidizable impurities (as SO2), (Analytical Reagent Grade)")	-	1000	-
4.1.3 & Table 1, S.No (vii)("Nitrates (as NO3) (Analytical Reagent Grade)")	-	1000	-
4.1.3 & Table 1, S.No (vii)("Ammonia (as NH3) (Analytical Reagent Grade)")	-	1000	-
4.3.2.2 a)("Antimony (as Sb) (Battery Grade Concentrated acid)")	-	1000	-
4.3.2.2 a)("Antimony (as Sb) (Battery Grade Diluted acid)")	-	1000	-
4.3.2.2 b)(Platinum (as Pt) (Battery Grade Concentrated acid))	-	1000	-
4.3.2.2 b)(Platinum (as Pt) (Battery Grade Diluted acid))	-	1000	-
4.1, 4.1.1(Technical Grade (Description))	-	-	-
4.1, 4.1.2(Battery Grade (Concentrated) (Description))	-	-	-
4.1, 4.1.2(Battery Grade (Dilute) (Description))	-	-	-
4.1, 4.1.3(Chemically Pure Grade (Description))	-	-	-
4.1, 4.1.3(Analytical Reagent Grade (Description))	-	-	-
4.3.1 & Table 1, S.No (i)("Total acidity (as H2SO4) (Technical Grade)")	-	-	-
4.3.1 & Table 1, S.No (ii)("Residue on ignition (Technical Grade)")	-	-	-
4.3.1 & Table 1, S.No (iii)("Iron (as Fe) (Technical Grade)")	-	-	-
4.3.1 & Table 1, S.No (v)("Heavy metals (as lead) (Technical Grade)")	-	-	-
4.3.1 & Table 1, S.No (vi)("Arsenic (as As) (Technical Grade)")	-	-	-
4.3.2 & Table 1, S.No (i)("Total acidity (as H2SO4) (Battery Grade Concentrated)")	-	-	-
4.3.2 & Table 1, S.No (ii)("Residue on ignition (Battery Grade Concentrated)")	-	-	-
4.3.2 & Table 1, S.No (iii)("Iron (as Fe) (Battery Grade Concentrated)")	-	-	-
4.3.2 & Table 1, S.No (iv)("Chloride (Battery Grade Concentrated)")	-	-	-
4.3.2 & Table 1, S.No (vi)("Arsenic (as As) (Battery Grade Concentrated)")	-	-	-
4.3.2 & Table 1, S.No (vii)("Oxidizable impurities (as SO2), (Battery Grade Concentrated)")	-	-	-
4.3.2 & Table 1, S.No (viii)("Organic Matter (Battery Grade Concentrated)")	-	-	-
4.3.2 & Table 1, S.No (xi)("Selenium (as Se) (Battery Grade Concentrated)")	-	-	-
4.3.2 & Table 1, S.No (xii)("Manganese (as Mn) (Battery Grade Concentrated)")	-	-	-
4.3.2 & Table 1, S.No (xiii)("Copper (as Cu) (Battery Grade Concentrated)")	-	-	-
4.3.2 & Table 1, S.No (xiv)("Zinc (as Zn) (Battery Grade Concentrated)")	-	-	-
4.3.2 & Table 1, S.No (xv)("Nitrates, nitrites and ammonia (as N) (Battery Grade Concentrated)")	-	-	-
4.3.2 & Table 1, S.No (i)("Total acidity (as H2SO4) (Battery Grade Diluted)")	-	-	-
4.3.2 & Table 1, S.No (ii)("Residue on ignition (Battery Grade Diluted)")	-	-	-
4.3.2 & Table 1, S.No (iii)("Iron (as Fe) (Battery Grade Diluted)")	-	-	-
4.3.2 & Table 1, S.No (iv)("Chloride (Battery Grade Diluted)")	-	-	-
4.3.2 & Table 1, S.No (vi)("Arsenic (as As) (Battery Grade Diluted)")	-	-	-
4.3.2 & Table 1, S.No (vii)("Oxidizable impurities (as SO2), (Battery Grade Diluted)")	-	-	-
4.3.2 & Table 1, S.No (xi)("Selenium (as Se) (Battery Grade Diluted)")	-	-	-
4.3.2 & Table 1, S.No (xii)("Manganese (as Mn) (Battery Grade Diluted)")	-	-	-
4.3.2 & Table 1, S.No (xiii)("Copper (as Cu) (Battery Grade Diluted)")	-	-	-
4.3.2 & Table 1, S.No (xiv)("Zinc (as Zn) (Battery Grade Diluted)")	-	-	-
4.3.2 & Table 1, S.No (xv)("Nitrates, nitrites and ammonia (as N) (Battery Grade Diluted)")	-	-	-
4.1.3 & Table 1, S.No (i)("Total acidity (as H2SO4) (Chemically Pure Grade)")	-	-	-
4.1.3 & Table 1, S.No (ii)("Residue on ignition (Chemically Pure Grade)")	-	-	-
4.1.3 & Table 1, S.No (iii)("Iron (as Fe) (Chemically Pure Grade)")	-	-	-
4.1.3 & Table 1, S.No (iv)("Chloride (Chemically Pure Grade)")	-	-	-
4.1.3 & Table 1, S.No (v)("Heavy metals (as lead) (Chemically Pure Grade)")	-	-	-
4.1.3 & Table 1, S.No (vi)("Arsenic (as As) (Chemically Pure Grade)")	-	-	-
4.1.3 & Table 1, S.No (vii)("Oxidizable impurities (as SO2), (Chemically Pure Grade)")	-	-	-
4.1.3 & Table 1, S.No (xv)("Nitrates, nitrites and ammonia (as N) (Chemically Pure Grade)")	-	-	-
4.1.3 & Table 1, S.No (i)("Total acidity (as H2SO4) (Analytical Reagent Grade)")	-	-	-
4.1.3 & Table 1, S.No (ii)("Residue on ignition (Analytical Reagent Grade)")	-	-	-
4.1.3 & Table 1, S.No (iii)("Iron (as Fe) (Analytical Reagent Grade)")	-	-	-
4.1.3 & Table 1, S.No (iv)("Chloride (Analytical Reagent Grade)")	-	-	-
4.1.3 & Table 1, S.No (v)("Heavy metals (as lead) (Analytical Reagent Grade)")	-	-	-
4.1.3 & Table 1, S.No (vi)("Arsenic (as As) (Analytical Reagent Grade)")	-	-	-
4.1.3 & Table 1, S.No (vi)("Arsenic (as As) (Analytical Reagent Grade)")	-	-	-
4.1.3 & Table 1, S.No (vii)("Oxidizable impurities (as SO2), (Analytical Reagent Grade)")	-	-	-
4.1.3 & Table 1, S.No (vii)("Nitrates (as NO3) (Analytical Reagent Grade)")	-	-	-
4.1.3 & Table 1, S.No (vii)("Ammonia (as NH3) (Analytical Reagent Grade)")	-	-	-
4.3.2.2 a)("Antimony (as Sb) (Battery Grade Concentrated acid)")	-	-	-
4.3.2.2 a)("Antimony (as Sb) (Battery Grade Diluted acid)")	-	-	-
4.3.2.2 b)(Platinum (as Pt) (Battery Grade Concentrated acid))	-	-	-
4.3.2.2 b)(Platinum (as Pt) (Battery Grade Diluted acid))	-	-	-

31 Dec, 2026

-
Included w.e.f.10.12.2024

7843

ALAIPURIA TEST HOUSE PRIVATE LIMITED, GHAZIABAD

8180426

IS 302 : Part 2 : Sec 201 (2008)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 201 electric immersion water heaters (First Revision)

-----

13500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.6 of IS 302-‐2-‐201:2008(Classification)	-	200	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	200	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.8 of IS 302‐2-201: 2008(Protection Against Access to Live Parts)	-	500	-
Cl.10 of IS 302‐2‐201:2008(Power Input and Current )	-	1500	-
Cl.11 of IS 302-2201: 2008(Heating)	-	1000	-
Cl.11 of IS 302-2201: 2008(Heating)	-	0	-
Cl.11 of IS 302-2201: 2008(Heating)	-	0	-
Cl.11 of IS 302-2201: 2008(Heating)	-	0	-
Cl.11 of IS 302-2201: 2008(Heating)	-	0	-
Cl.11 of IS 302-2201: 2008(Heating)	-	0	-
Cl.11 of IS 302-2201: 2008(Heating)	-	0	-
Cl.11 of IS 302-2201: 2008(Heating)	-	0	-
Cl.11 of IS 302-2201: 2008(Heating)	-	0	-
Cl.11 of IS 302-2201: 2008(Heating)	-	0	-
Cl.11 of IS 302-2201: 2008(Heating)	-	0	-
Cl.13 of IS 302-2-201: 2008(Leakage Current & Electric Strength at Operating Temperature)	-	1000	-
Cl.14 of IS 302‐2-201:2008(Transient Over Voltages )	-	500	-
Cl.15 of IS 302-2-201:2008(Moisture Resistance )	-	1000	-
Cl.15 of IS 302-2-201:2008(Moisture Resistance )	-	0	-
Cl.16 of IS 302-2-201:2008(Leakage Current & Electric Strength)	-	1000	-
Cl.16 of IS 302-2-201:2008(Leakage Current & Electric Strength)	-	0	-
Cl.17 of IS 302‐2-201: 2008(Overload Protection of Transformers & Associated Circuits)	-	500	-
Cl.19 of IS 302‐2-201: 2008(Abnormal Operation )	-	1000	-
Cl.19 of IS 302‐2-201: 2008(Abnormal Operation )	-	0	-
Cl.19 of IS 302‐2-201: 2008(Abnormal Operation )	-	0	-
Cl.19 of IS 302‐2-201: 2008(Abnormal Operation )	-	0	-
Cl.20 of IS 302-2-201: 2008(Stability & Mechanical Hazards)	-	200	-
Cl.21 of IS 302-2-201: 2008(Mechanical Strength )	-	200	-
Cl.21 of IS 302-2-201: 2008(Mechanical Strength )	-	0	-
Cl.21 of IS 302-2-201: 2008(Mechanical Strength )	-	0	-
Cl.22 of IS 302-2-201: 2008(Construction)	-	200	-
Cl.23 of 302-2-201:2008(Internal Wiring )	-	200	-
Cl.23 of 302-2-201:2008(Internal Wiring )	-	0	-
Cl.23 of 302-2-201:2008(Internal Wiring )	-	0	-
Cl.23 of 302-2-201:2008(Internal Wiring )	-	0	-
Cl.23 of 302-2-201:2008(Internal Wiring )	-	0	-
Cl.23 of 302-2-201:2008(Internal Wiring )	-	0	-
Cl.23 of 302-2-201:2008(Internal Wiring )	-	0	-
Cl.23 of 302-2-201:2008(Internal Wiring )	-	0	-
Cl.23 of 302-2-201:2008(Internal Wiring )	-	0	-
Cl.24 of IS 302-2-201: 2008(Component)	-	200	-
Cl.24 of IS 302-2-201: 2008(Component)	-	0	-
Cl.24 of IS 302-2-201: 2008(Component)	-	0	-
Cl.24 of IS 302-2-201: 2008(Component)	-	0	-
Cl.24 of IS 302-2-201: 2008(Component)	-	0	-
Cl.24 of IS 302-2-201: 2008(Component)	-	0	-
Cl.24 of IS 302-2-201: 2008(Component)	-	0	-
Cl.24 of IS 302-2-201: 2008(Component)	-	0	-
Cl.24 of IS 302-2-201: 2008(Component)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	500	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.26 of IS 302-2-201: 2008(Terminals for External Conductors)	-	200	-
Cl.27 of IS 302-2-201: 2008(Provision for Earthing )	-	1500	-
Cl.27 of IS 302-2-201: 2008(Provision for Earthing )	-	0	-
Cl.27 of IS 302-2-201: 2008(Provision for Earthing )	-	0	-
Cl.27 of IS 302-2-201: 2008(Provision for Earthing )	-	0	-
Cl.27 of IS 302-2-201: 2008(Provision for Earthing )	-	0	-
Cl.27 of IS 302-2-201: 2008(Provision for Earthing )	-	0	-
Cl.28 of IS 302-2-201: 2008(Screws & Connections )	-	200	-
Cl.29 of IS 302-2‐201:2008(Clearances, Creepage Distances and Solid Insulation )	-	500	-
Cl.30 of IS 302-2‐201:2008(Resistance to Heat and Fire )	-	500	-
Cl.31 of IS 302-2-201:2008(Resistance of Rusting )	-	500	-
4(GENERAL REQUIREMENTS)	-	100	-
5(GENERAL CONDITIONS FOR THE TESTS)	-	100	-
Cl.6 of IS 302-‐2-‐201:2008(Classification)	-	200	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	200	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	-
Cl.8 of IS 302‐2-201: 2008(Protection Against Access to Live Parts)	-	500	-
Cl.10 of IS 302‐2‐201:2008(Power Input and Current )	-	1500	-
Cl.11 of IS 302-2201: 2008(Heating)	-	1000	-
Cl.11 of IS 302-2201: 2008(Heating)	-	0	-
Cl.11 of IS 302-2201: 2008(Heating)	-	0	-
Cl.11 of IS 302-2201: 2008(Heating)	-	0	-
Cl.11 of IS 302-2201: 2008(Heating)	-	0	-
Cl.11 of IS 302-2201: 2008(Heating)	-	0	-
Cl.11 of IS 302-2201: 2008(Heating)	-	0	-
Cl.11 of IS 302-2201: 2008(Heating)	-	0	-
Cl.11 of IS 302-2201: 2008(Heating)	-	0	-
Cl.11 of IS 302-2201: 2008(Heating)	-	0	-
Cl.11 of IS 302-2201: 2008(Heating)	-	0	-
Cl.13 of IS 302-2-201: 2008(Leakage Current & Electric Strength at Operating Temperature)	-	1000	-
Cl.14 of IS 302‐2-201:2008(Transient Over Voltages )	-	500	-
Cl.15 of IS 302-2-201:2008(Moisture Resistance )	-	1000	-
Cl.15 of IS 302-2-201:2008(Moisture Resistance )	-	0	-
Cl.16 of IS 302-2-201:2008(Leakage Current & Electric Strength)	-	1000	-
Cl.16 of IS 302-2-201:2008(Leakage Current & Electric Strength)	-	0	-
Cl.17 of IS 302‐2-201: 2008(Overload Protection of Transformers & Associated Circuits)	-	500	-
Cl.19 of IS 302‐2-201: 2008(Abnormal Operation )	-	1000	-
Cl.19 of IS 302‐2-201: 2008(Abnormal Operation )	-	0	-
Cl.19 of IS 302‐2-201: 2008(Abnormal Operation )	-	0	-
Cl.19 of IS 302‐2-201: 2008(Abnormal Operation )	-	0	-
Cl.20 of IS 302-2-201: 2008(Stability & Mechanical Hazards)	-	200	-
Cl.21 of IS 302-2-201: 2008(Mechanical Strength )	-	200	-
Cl.21 of IS 302-2-201: 2008(Mechanical Strength )	-	0	-
Cl.21 of IS 302-2-201: 2008(Mechanical Strength )	-	0	-
Cl.22 of IS 302-2-201: 2008(Construction)	-	200	-
Cl.23 of 302-2-201:2008(Internal Wiring )	-	200	-
Cl.23 of 302-2-201:2008(Internal Wiring )	-	0	-
Cl.23 of 302-2-201:2008(Internal Wiring )	-	0	-
Cl.23 of 302-2-201:2008(Internal Wiring )	-	0	-
Cl.23 of 302-2-201:2008(Internal Wiring )	-	0	-
Cl.23 of 302-2-201:2008(Internal Wiring )	-	0	-
Cl.23 of 302-2-201:2008(Internal Wiring )	-	0	-
Cl.23 of 302-2-201:2008(Internal Wiring )	-	0	-
Cl.23 of 302-2-201:2008(Internal Wiring )	-	0	-
Cl.24 of IS 302-2-201: 2008(Component)	-	200	-
Cl.24 of IS 302-2-201: 2008(Component)	-	0	-
Cl.24 of IS 302-2-201: 2008(Component)	-	0	-
Cl.24 of IS 302-2-201: 2008(Component)	-	0	-
Cl.24 of IS 302-2-201: 2008(Component)	-	0	-
Cl.24 of IS 302-2-201: 2008(Component)	-	0	-
Cl.24 of IS 302-2-201: 2008(Component)	-	0	-
Cl.24 of IS 302-2-201: 2008(Component)	-	0	-
Cl.24 of IS 302-2-201: 2008(Component)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	1000	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	-
Cl.26 of IS 302-2-201: 2008(Terminals for External Conductors)	-	200	-
Cl.27 of IS 302-2-201: 2008(Provision for Earthing )	-	1000	-
Cl.27 of IS 302-2-201: 2008(Provision for Earthing )	-	0	-
Cl.27 of IS 302-2-201: 2008(Provision for Earthing )	-	0	-
Cl.27 of IS 302-2-201: 2008(Provision for Earthing )	-	0	-
Cl.27 of IS 302-2-201: 2008(Provision for Earthing )	-	0	-
Cl.27 of IS 302-2-201: 2008(Provision for Earthing )	-	0	-
Cl.28 of IS 302-2-201: 2008(Screws & Connections )	-	200	-
Cl.29 of IS 302-2‐201:2008(Clearances, Creepage Distances and Solid Insulation )	-	500	-
Cl.30 of IS 302-2‐201:2008(Resistance to Heat and Fire )	-	500	-
Cl.31 of IS 302-2-201:2008(Resistance of Rusting )	-	500	-
4(GENERAL REQUIREMENTS)	-	100	-
5(GENERAL CONDITIONS FOR THE TESTS)	-	100	-

03 Oct, 2027

-
Included.w.e.f.07.11.2024 Exclusion 32 (RADIATION, TOXICITY AND SIMILAR HAZARDS) 19.11.4.1 to 19.11.4.5 (EMI/EMC)

7844

URS PRODUCTS AND TESTING PVT. LTD. (A29), NOIDA

8168906

IS 16103 : Part 1 (2012)

Led modules for general lighting: Part 1 safety requirements

35000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking)	-	3000	-
8(Terminals)	-	3000	-
9(PROVISION FOR EARTHING)	-	5000	-
10(Protection against accidental contact with live parts)	-	5000	-
11(Mositure Resistance and Insulation)	-	5000	-
12(Electric Strength)	-	5000	-
13(Fault conditions)	-	4000	-
15(Construction)	-	3000	-
16(Creepage distance and clearances)	-	2000	-
17(Screws, current carrying parts and connections)	-	4000	-
18(Resistance to heat, fire and tracking)	-	4000	-
19(Resistance to corrosion)	-	4000	-
21(Heat management)	-	3000	-
21(Heat management)	-	2000	-

-
Included w.e.f 01.01.2025

7845

ALAIPURIA TEST HOUSE PRIVATE LIMITED, GHAZIABAD

8180426

IS 302 : Part 2 : Sec 13 (1994)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 13 frying pans, deep fat fryers and similar appliances

-----

24000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
31(Resistance to Rusting)	-	1000	-
30(Resistance to Heat, Fire and Tracking)	-	1000	-
29(Clearances, Creepage Distances & Solid Insulation)	-	500	-
28(Screws & Connections)	-	500	-
27(Provision For Earthing)	-	1500	-
26(Terminals For External Conductors)	-	500	-
25(Supply Connection & External Flexible Cables and Cords)	-	500	-
24(Components)	-	500	-
23(Internal wiring)	-	500	-
22(Construction)	-	500	-
21(Mechanical strength)	-	500	-
20(Stability & Mechanical Hazards)	-	500	-
19(Abnormal Operation)	-	2000	-
18(Endurance)	-	100	-
17(Overload Protection/ Overload Protection of Transformers & Associated Circuits)	-	500	-
16(Leakage Current and Electric Strength)	-	1500	-
15(Moisture Resistance)	-	3000	-
14(Transient Over Voltage)	-	1000	-
13(Leakage Current and Electric Strength at Operating Temperature)	-	1500	-
11(Temperature Rise/Heating)	-	2000	-
10(Power Input)	-	2000	-
9(Starting Of Motor Operated Appliances)	-	200	-
8(Protection against Electric Shock/ Protection against Access to Live Parts)	-	1000	-
7(Marking/ Marking & Instructions)	-	500	-
6(Classification)	-	500	-
5(Rating)	-	200	-
31(Resistance to Rusting)	-	1000	-
30(Resistance to Heat, Fire and Tracking)	-	1000	-
29(Clearances, Creepage Distances & Solid Insulation)	-	500	-
28(Screws & Connections)	-	500	-
27(Provision For Earthing)	-	1500	-
26(Terminals For External Conductors)	-	500	-
25(Supply Connection & External Flexible Cables and Cords)	-	500	-
24(Components)	-	500	-
23(Internal wiring)	-	500	-
22(Construction)	-	500	-
21(Mechanical strength)	-	500	-
20(Stability & Mechanical Hazards)	-	500	-
19(Abnormal Operation)	-	2000	-
18(Endurance)	-	100	-
17(Overload Protection/ Overload Protection of Transformers & Associated Circuits)	-	500	-
16(Leakage Current and Electric Strength)	-	1500	-
15(Moisture Resistance)	-	3000	-
14(Transient Over Voltage)	-	1000	-
13(Leakage Current and Electric Strength at Operating Temperature)	-	1500	-
11(Temperature Rise/Heating)	-	2000	-
10(Power Input)	-	2000	-
9(Starting Of Motor Operated Appliances)	-	200	-
8(Protection against Electric Shock/ Protection against Access to Live Parts)	-	1000	-
7(Marking/ Marking & Instructions)	-	500	-
6(Classification)	-	500	-
5(Rating)	-	200	-

03 Oct, 2027

-
Included w.e.f.18.11.2024 Exclusion 32 (Radiation ,Toxicity and similar hazards) 19.11.4.1 to 19.11.4.7 (EMI/EMC)

7846

INDIAN TESTING LABORATORY PRIVATE LIMITED, GREATER NOIDA

8171306

IS 12786 (2024)

Irrigation equipment - Polyethylene pipes for irrigation laterals - Specification (first revision)

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(Material)	-	1000	-
Cl-4.2(Carbon content of finished PE lateral pipe)	-	500	-
Cl-5.1(Dimensions of pipes and wall thicknesses)	-	1000	-
Cl-6.0(Visual Appearance)	-	500	-
Cl-7.1(Hydraulic Characteristics- Internal pressure creep rupture test)	-	2000	-
Cl-7.1(Hydraulic Characteristics- quality acceptance test)	-	2000	-
Cl-7.2(Reversion Test)	-	1000	-
Cl-7.3(Tensile Test)	-	1000	-
Cl-7.3.1(Test Piece)	-	100	-
Cl-7.3.2(Procedure)	-	100	-
Cl-7.4(Susceptibility to Environmental Stress Cracking)	-	500	-
Cl-8.0(Supply of pipes)	-	100	-
Cl-9.0(Coiling)	-	500	-
Cl-10.0(Sampling and criteria for conformity)	-	100	-
Cl-11(Marking)	-	100	-
3(Class of Pipe)	-	100	-
5.1 & Table 1(Dimensions of Pipes - Outside diameters)	-	500	-
5.1 & Table 1(Dimensions of Pipes - Wall thickness)	-	500	-
6(Visual Appearance)	-	500	-
7.1 & Table 2(Hydraulic Characteristics)	-	2000	-
7.1 & Table 2(Hydraulic Characteristics)	-	2000	-
7.2(Reversion Test)	-	1000	-
7.3(Tensile Strength)	-	1000	-
7.3(Elongation at Break)	-	1000	-
7.4(SusceptibiIity to Environmental Stress Cracking)	-	500	-
4.2(a)(Carbon Black Content-IS 2530)	-	500	-
4.2(b)(Carbon Black Dispersion-IS 2530)	-	500	-

15 Aug, 2028

-
Included w.e.f. 12.12.2024

7847

INDIAN TESTING LABORATORY PRIVATE LIMITED, GREATER NOIDA

8171306

IS 444 (2017)

Rubber hoses, textile - Reinforced, for general - Purpose water applications - Specification (Fifth Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Classification - IS 444)	-	200	-
5(Lining - IS 444)	-	200	-
5(Reinforcement - IS 444)	-	200	-
5(Cover - IS 444)	-	200	-
5(Lining and Cover - IS 444)	-	200	-
6.1- Table 1(Internal diameters - ISO 4671)	-	500	-
6.2(Concentricity - ISO 4671)	-	500	-
6.3(Length -IS 4671)	-	500	-
6.4( thickness of the lining plus cover - ISO 4671)	-	500	-
6.4(If the cover is fluted, the depth of the flutes - ISO 4671)	-	500	-
7.1 - Table 2( tensile strength of Lining - ISO 37 )	-	1000	-
7.1 - Table 2( tensile strength of Cover - ISO 37 )	-	1000	-
7.1 - Table 2(elongation at break of Lining - ISO 37)	-	1000	-
7.1 - Table 2(elongation at break of Cover - ISO 37)	-	1000	-
7.1 - Table 2(Change in tensile strength of Lining from original value after ageing(max) - ISO 188 and ISO 37)	-	1000	-
7.1 - Table 2(Change in tensile strength of Cover from original value after ageing(max) - ISO 188 and ISO 37)	-	1000	-
7.1 - Table 2(Change in elongation at break of Lining from original value after ageing (max.) - ISO 188 and ISO 37)	-	1000	-
7.1 - Table 2(Change in elongation at break of Cover from original value after ageing (max.) - ISO 188 and ISO 37)	-	1000	-
7.2 - Table 3(Proof pressure at 23 °C - ISO 1402)	-	1000	-
7.2 - Table 3(Change in length at proof pressure - ISO 1402)	-	1000	-
7.2 - Table 3(Minimum burst pressure - ISO 1402)	-	1000	-
7.2 - Table 3(Adhesion between components - ISO 8033)	-	1000	-
7.2 - Table 3(Ozone resistance - ISO 7326)	-	2000	-
7.2 - Table 3(Flexibility at 23 °C - Method A of ISO 1746)	-	1000	-
7.2 - Table 3(Low-temperature flexibility - Method B of ISO 4672)	-	1000	-

15 Aug, 2028

-
Included w.e.f. 12.12.2024

7848

CENTRAL INSTITUTE OF PETROCHEMICALS ENGINEERING & TECHNOLOGY - CIPET, HALDIA

5116334

IS 2508 (2016)

Polyethylene films and sheets - Specification (Third Revision)

All Types

18256 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1(Appearance)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
5.1.2(Film Form)	-	0	-
5.1.3(Odour)	-	0	-
5.1.4(Density, Cl.5 of IS 13360(Part-3/Section-1))	-	700	Discount of 25% is applicable on Total Test Charges only for BIS
5.1.5(Melt Flow Index. Cl 6, 7 of IS 13360(Part-4/Section-1))	-	1100	Discount of 25% is applicable on Total Test Charges only for BIS
Cl.5.1.6(a)(Carbon Black Content)	-	0	-
Cl.5.1.6(b)(Ash content)	-	0	-
Cl.5.1.6(c)(Dispersion of Carbon Black)	-	0	-
5.2.1.1(Nominal Thickness)	-	0	-
5.2.1.2(Nominal width)	-	0	-
5.2.2(Tolerance on Thickness, Annex-A)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
Clause 5.2.3(Tolerance on Width)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
6.1, Table 1(Tensile strength at break. A) Machine Direction. IS 13360 (Part 5/Sec 1))	-	1800	Testing charge + Specimen ( 1300+500) Discount of 25% is applicable on Total Test Charges only for BIS
6.1, Table 1(Tensile strength at break. B) Transverse Direction. IS 13360 (Part 5/Sec 3))	-	1300	Discount of 25% is applicable on Total Test Charges only for BIS
6.1, Table 1(Ageing test at (70-1)c for 7 days , cl 4 IS 7016 )	-	4200	Ageing changes (4200) Discount of 25% is applicable on Total Test Charges only for BIS
6.1, Table 1(Elongation at break ,A) Machine direction .IS 13360(Part-5/sec-1) )	-	0	-
6.1, Table 1(Elongation at break ,B) Cross-machine direction..IS 13360(Part-5/sec-3) )	-	0	-
6.1, Table 1(Dartimpact strength Method B of IS 13360 (Part-5/sec-6) )	-	850	Discount of 25% is applicable on Total Test Charges only for BIS
6.1, Table 1(Tear resistence. A) Machine direction Annex B)	-	1100	Discount of 25% is applicable on Total Test Charges only for BIS
6.1, Table 1(Tear resistence. B) Transverse direction )	-	1100	Discount of 25% is applicable on Total Test Charges only for BIS
7.1. Table 2(Tensile strength at break A) Machine direction IS 13360 (Part-5/sec-1) )	-	0	-
7.1. Table 2(Tensile strength at break,B) Crosse machine direction IS 13360 (Part-5/sec-3) )	-	0	-
7.1. Table 2(Ageing test at (70-1)c for 7 days , cl 4 IS 7016 )	-	0	-
7.1. Table 2(Elongation at break , A) Machine direction IS 13360 (Part-5/sec-3) IS 13360 (Part-5/sec-1) )	-	0	-
7.1. Table 2(Elongation at break , A) Transverse direction IS 13360 (Part-5/sec-3) )	-	0	-
7.1. Table 2(Dart impact strenght , Method A of IS 3360 (Part-5/sec-6) )	-	0	-
Clause 6.1(Table 1)(Decrease in Tensile Strength after Ageing(Machine Direction))	-	1300	Discount of 25% is applicable on Total Test Charges only for BIS
Clause 6.1(Table 1)(Decrease in Tensile Strength after Ageing(Transverse Direction))	-	1300	Discount of 25% is applicable on Total Test Charges only for BIS
Clause 7.1(Table 2)(Decrease in Tensile Strength after Ageing(Machine Direction))	-	0	-
Clause 7.1(Table 2)(Decrease in Tensile Strength after Ageing(Transverse Direction))	-	0	-
Clause 8.1(Table 3)(Break strength)	-	0	-
Clause 8.1(Table 3)(Break Elongation)	-	0	-
8.1, Table 3(Tear resistance , Annex B)	-	0	-
8.1, Table 3(Puncture resistance , Annex C)	-	1100	Discount of 25% is applicable on Total Test Charges only for BIS
9.1, Table 4(Tensile properties ,A) Yield strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	2600	Testing charge + Specimen (MD/TD) (2600) Discount of 25% is applicable on Total Test Charges only for BIS
9.1, Table 4(Tensile properties , B) Break strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	-
9.1, Table 4(Tensile properties ,C) Yield elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	-
9.1, Table 4(Tensile properties ,D) Break elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	-
9.1, Table 4(Tear resistance , Annex B)	-	0	-
9.1, Table 4(Puncture resistance , Annex C)	-	0	-

-
-

7849

SGS India Private Limited-Multilaboratory, Chennai

6114716

IS 13428 (2024)

PACKAGED NATURAL MINERAL WATER - SPECIFICATION Third Revision

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1.1(Escherichia coli)	-	150	-
6.1.2(Coliform)	-	150	-
6.1.3(Faecal Streptococci)	-	375	-
6.1.4(Sulphite Reducing Anaerobe)	-	150	-
6.1.5(Pseudomonas aeruginosa)	-	300	-
6.1.6(Yeast and moould)	-	150	-
6.1.7(Salmonella)	-	675	-
6.1.8(Vibrio Cholera)	-	450	-
6.2/Table 1/i(Colour)	-	150	-
6.2/Table 1/ii(Odour)	-	37.5	-
6.2/Table 1/iii(Taste)	-	37.5	-
6.2/Table 1/iv(Turbidity)	-	37.5	-
6.2/Table 1/v(Total Dissoved)	-	75	-
6.2/Table 1/vi(pH Value)	-	37.5	-
6.2/Table 2/i(Nitrate)	-	300	-
6.2/Table 2/ii(Nitrite)	-	225	-
6.2/Table 2/iii(Sulphide)	-	150	-
6.2/Table 2/iv(Manganese)	-	150	-
6.2/Table 2/v(Copper)	-	150	-
6.2/Table 2/vi(Fluoride)	-	150	-
6.2/Table 2/vii(Barium)	-	150	-
6.2/Table 2/viii(Antimony)	-	150	-
6.2/Table 2/ix(Borate)	-	225	-
6.2/Table 2/x(Silver)	-	75	-
6.2/Table 2/xi(Chloride)	-	75	-
6.2/Table 2/xii(Sulphate)	-	150	-
6.2/Table 2/xiii(Magnesium)	-	75	-
6.2/Table 2/xiv(Calcium)	-	75	-
6.2/Table 2/xv(Sodium)	-	75	-
6.2/Table 2/xvi(Alkalinity)	-	75	-
6.2/Table 2/xvii(Selenium)	-	75	-
6.2/Table 2/xviii(Mineral Oil)	-	150	-
6.2/Table 2/xix(Phenolic Compounds)	-	375	-
6.2/Table 2/xx(Anionic Surface active agents)	-	375	-
6.2/Table 3/i(Arsenic)	-	150	-
6.2/Table 3/ii(Cadmium)	-	150	-
6.2/Table 3/iii(Cyanide)	-	225	-
6.2/Table 3/iv(Chromium)	-	75	-
6.2/Table 3/v(Mercury)	-	150	-
6.2/Table 3/vi(Lead)	-	150	-
6.2/Table 3/vii(Nickel)	-	75	-
6.2/Table 3/viii(Polychlorinated biphenyle (PCB))	-	300	-
6.2/Table 3/ix(Polynuclear aromatic hydrocarbons)	-	300	-
6.2/Table 3/x(Uranium)	-	150	-
Cl- 6.3, Annex N (i)(P,P -DDE)	-	2250	Testing charge applicable for Total pesticides (package)
Cl- 6.3, Annex N (i)(O,P -DDE)	-	0	-
Cl- 6.3, Annex N (i)(P,P- DDT)	-	0	-
Cl- 6.3, Annex N (i)(O,P -DDT)	-	0	-
Cl-6.3, Annex N (i)(P,P- DDD)	-	0	-
Cl-6.3, Annex N (i)(O,P-DDD)	-	0	-
Cl- 6.3, Annex N (ii)(γ-HCH (lindane))	-	0	-
Cl- 6.3, Annex N (iii)(α-HCH)	-	0	-
Cl- 6.3, Annex N (iii)(β-HCH)	-	0	-
Cl- 6.3, Annex N (iii)(δ - HCH)	-	0	-
Cl- 6.3, Annex N (iv)(Endosulfan - α)	-	0	-
Cl- 6.3, Annex N (iv)(Endosulfan - β)	-	0	-
Cl- 6.3, Annex N (iv)(Endosulfan - sulphate)	-	0	-
Cl- 6.3, Annex N (v)(Monocrotophos)	-	0	-
Cl- 6.3, Annex N (vi)(Ethion)	-	0	-
Cl- 6.3, Annex N (vii)(Chlorpyrifos)	-	0	-
Cl- 6.3, Annex N (viii)(Phorate and its oxygen analogue)	-	0	-
Cl- 6.3, Annex N (viii)(phorate sulphoxide)	-	0	-
Cl- 6.3, Annex N (viii)(phorate sulphone)	-	0	-
Cl- 6.3, Annex N (ix)(2,4-D)	-	0	-
Cl- 6.3, Annex N (x)(Butachlor)	-	0	-
Cl- 6.3, Annex N (xi)(Isoproturon)	-	0	-
Cl- 6.3, Annex N (xii)(Alachlor)	-	0	-
Cl- 6.3, Annex N (xiii)(Atrazine)	-	0	-
Cl- 6.3, Annex N (xiv)(Methyl parathion)	-	0	-
Cl- 6.3, Annex N (xiv)(Methyl paraoxon)	-	0	-
Cl- 6.3, Annex N (xv)(Malathion)	-	0	-
Cl- 6.3, Annex N (xv)(malaoxon)	-	0	-
Cl- 6.3, Annex N (xvi)(Aldrin)	-	0	-
Cl-6.1.3(Staphylococcus aureus)	-	0	-
Cl-6.1.7(Shigella)	-	0	-
Cl-6.1.8(V. parahaemolyticus)	-	0	-
Cl-6.3, Annex N (XVI)(Dieldrin)	-	0	-
6.1.1(Escherichia coli)	-	0	-
6.1.2(Coliform)	-	0	-
6.1.3(Faecal Streptococci)	-	0	-
6.1.4(Sulphite Reducing Anaerobe)	-	0	-
6.1.5(Pseudomonas aeruginosa)	-	0	-
6.1.6(Yeast and moould)	-	0	-
6.1.7(Salmonella)	-	0	-
6.1.8(Vibrio Cholera)	-	0	-
6.2/Table 1/i(Colour)	-	0	-
6.2/Table 1/ii(Odour)	-	0	-
6.2/Table 1/iii(Taste)	-	0	-
6.2/Table 1/iv(Turbidity)	-	0	-
6.2/Table 1/v(Total Dissoved)	-	0	-
6.2/Table 1/vi(pH Value)	-	0	-
6.2/Table 2/i(Nitrate)	-	0	-
6.2/Table 2/ii(Nitrite)	-	0	-
6.2/Table 2/iii(Sulphide)	-	0	-
6.2/Table 2/iv(Manganese)	-	0	-
6.2/Table 2/v(Copper)	-	0	-
6.2/Table 2/vi(Fluoride)	-	0	-
6.2/Table 2/vii(Barium)	-	0	-
6.2/Table 2/viii(Antimony)	-	0	-
6.2/Table 2/ix(Borate)	-	0	-
6.2/Table 2/x(Silver)	-	0	-
6.2/Table 2/xi(Chloride)	-	0	-
6.2/Table 2/xii(Sulphate)	-	0	-
6.2/Table 2/xiii(Magnesium)	-	0	-
6.2/Table 2/xiv(Calcium)	-	0	-
6.2/Table 2/xv(Sodium)	-	0	-
6.2/Table 2/xvi(Alkalinity)	-	0	-
6.2/Table 2/xvii(Selenium)	-	0	-
6.2/Table 2/xviii(Mineral Oil)	-	0	-
6.2/Table 2/xix(Phenolic Compounds)	-	0	-
6.2/Table 2/xx(Anionic Surface active agents)	-	0	-
6.2/Table 3/i(Arsenic)	-	0	-
6.2/Table 3/ii(Cadmium)	-	0	-
6.2/Table 3/iii(Cyanide)	-	0	-
6.2/Table 3/iv(Chromium)	-	0	-
6.2/Table 3/v(Mercury)	-	0	-
6.2/Table 3/vi(Lead)	-	0	-
6.2/Table 3/vii(Nickel)	-	0	-
6.2/Table 3/viii(Polychlorinated biphenyle (PCB))	-	0	-
6.2/Table 3/ix(Polynuclear aromatic hydrocarbons)	-	0	-
6.2/Table 3/x(Uranium)	-	0	-
Cl- 6.3, Annex N (i)(P,P -DDE)	-	0	-
Cl- 6.3, Annex N (i)(O,P -DDE)	-	0	-
Cl- 6.3, Annex N (i)(P,P- DDT)	-	0	-
Cl- 6.3, Annex N (i)(O,P -DDT)	-	0	-
Cl-6.3, Annex N (i)(P,P- DDD)	-	0	-
Cl-6.3, Annex N (i)(O,P-DDD)	-	0	-
Cl- 6.3, Annex N (ii)(γ-HCH (lindane))	-	0	-
Cl- 6.3, Annex N (iii)(α-HCH)	-	0	-
Cl- 6.3, Annex N (iii)(β-HCH)	-	0	-
Cl- 6.3, Annex N (iii)(δ - HCH)	-	0	-
Cl- 6.3, Annex N (iv)(Endosulfan - α)	-	0	-
Cl- 6.3, Annex N (iv)(Endosulfan - β)	-	0	-
Cl- 6.3, Annex N (iv)(Endosulfan - sulphate)	-	0	-
Cl- 6.3, Annex N (v)(Monocrotophos)	-	0	-
Cl- 6.3, Annex N (vi)(Ethion)	-	0	-
Cl- 6.3, Annex N (vii)(Chlorpyrifos)	-	0	-
Cl- 6.3, Annex N (viii)(Phorate and its oxygen analogue)	-	0	-
Cl- 6.3, Annex N (viii)(phorate sulphoxide)	-	0	-
Cl- 6.3, Annex N (viii)(phorate sulphone)	-	0	-
Cl- 6.3, Annex N (ix)(2,4-D)	-	0	-
Cl- 6.3, Annex N (x)(Butachlor)	-	0	-
Cl- 6.3, Annex N (xi)(Isoproturon)	-	0	-
Cl- 6.3, Annex N (xii)(Alachlor)	-	0	-
Cl- 6.3, Annex N (xiii)(Atrazine)	-	0	-
Cl- 6.3, Annex N (xiv)(Methyl parathion)	-	0	-
Cl- 6.3, Annex N (xiv)(Methyl paraoxon)	-	0	-
Cl- 6.3, Annex N (xv)(Malathion)	-	0	-
Cl- 6.3, Annex N (xv)(malaoxon)	-	0	-
Cl- 6.3, Annex N (xvi)(Aldrin)	-	0	-
Cl-6.1.3(Staphylococcus aureus)	-	0	-
Cl-6.1.7(Shigella)	-	0	-
Cl-6.1.8(V. parahaemolyticus)	-	0	-
Cl-6.3, Annex N (XVI)(Dieldrin)	-	0	-

14 Feb, 2028

-
Included w.e.f 30.04.2025 Exclusion:Cl 6.2/Table 4/i (Alpha emitters, Bq/l, Max), Cl 6.2/Table 4/ii (Beta emitters, Bq/l, Max)

7850

INDIAN TESTING LABORATORY PRIVATE LIMITED, GREATER NOIDA

8171306

IS 12585 (2023)

SPECIFICATION FOR THERMOPLASTIC HOSES (TEXTILE REINFORCED) FOR WATER - GENERAL PURPOSE ( First Revision of IS 12585 )

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Materials and Construction)	-	250	-
5(Materials and Construction)	-	250	-
6.1(Dimensions (Inside diameters and tolerances on inside diameter))	-	250	-
6.2(Concentricity)	-	250	-
6.3(Tolerance on Length)	-	250	-
6.4(Minimum Wall Thickness)	-	250	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Tensile Strength) - Lining)	-	250	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Tensile Strength) - Cover)	-	250	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Elongation at break) - Lining)	-	250	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Elongation at break) - Cover)	-	250	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials-Resistance to ageing (Change in Tensile Strength from original value, max) -Lining)	-	800	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Resistance to ageing(Change in Tensile Strength from original value, max) -Cover)	-	800	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Resistance to ageing(Change in Elongation at break from original value, max) - Lining)	-	800	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Resistance to ageing(Change in Elongation at break from original value, max) - Cover)	-	800	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Loss in mass on heating- Lining)	-	800	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Loss in mass on heating- Cover)	-	800	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 23°C - Type 1)	-	800	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 23°C - Type 2)	-	800	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 23°C - Type 3)	-	800	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 23°C - Type 1)	-	800	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 23°C - Type 2)	-	800	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 23°C - Type 3)	-	800	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 60°C - Type 1)	-	800	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 60°C - Type 2)	-	800	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 60°C - Type 3)	-	800	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 60°C - Type 1)	-	800	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 60°C - Type 2)	-	800	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 60°C - Type 3)	-	800	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Change in Length at maximum working pressure at 23°C (±8%))	-	800	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Adhesion between components)	-	800	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - UV resistance (Xenon-arc lamp))	-	800	-
7, 7.2 -Table 3(Flexibility at 23°C)	-	800	-
7, 7.2 -Table 3(Low Temperature flexibility)	-	800	-
5(Materials and Construction)	-	0	-
5(Materials and Construction)	-	0	-
6.1(Dimensions (Inside diameters and tolerances on inside diameter))	-	0	-
6.2(Concentricity)	-	0	-
6.3(Tolerance on Length)	-	0	-
6.4(Minimum Wall Thickness)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Tensile Strength) - Lining)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Tensile Strength) - Cover)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Elongation at break) - Lining)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Elongation at break) - Cover)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials-Resistance to ageing (Change in Tensile Strength from original value, max) -Lining)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Resistance to ageing(Change in Tensile Strength from original value, max) -Cover)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Resistance to ageing(Change in Elongation at break from original value, max) - Lining)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Resistance to ageing(Change in Elongation at break from original value, max) - Cover)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Loss in mass on heating- Lining)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Loss in mass on heating- Cover)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 23°C - Type 1)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 23°C - Type 2)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 23°C - Type 3)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 23°C - Type 1)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 23°C - Type 2)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 23°C - Type 3)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 60°C - Type 1)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 60°C - Type 2)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 60°C - Type 3)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 60°C - Type 1)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 60°C - Type 2)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 60°C - Type 3)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Change in Length at maximum working pressure at 23°C (±8%))	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Adhesion between components)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - UV resistance (Xenon-arc lamp))	-	0	-
7, 7.2 -Table 3(Flexibility at 23°C)	-	0	-
7, 7.2 -Table 3(Low Temperature flexibility)	-	0	-
5(Materials and Construction)	-	0	-
5(Materials and Construction)	-	0	-
6.1(Dimensions (Inside diameters and tolerances on inside diameter))	-	0	-
6.2(Concentricity)	-	0	-
6.3(Tolerance on Length)	-	0	-
6.4(Minimum Wall Thickness)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Tensile Strength) - Lining)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Tensile Strength) - Cover)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Elongation at break) - Lining)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Elongation at break) - Cover)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials-Resistance to ageing (Change in Tensile Strength from original value, max) -Lining)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Resistance to ageing(Change in Tensile Strength from original value, max) -Cover)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Resistance to ageing(Change in Elongation at break from original value, max) - Lining)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Resistance to ageing(Change in Elongation at break from original value, max) - Cover)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Loss in mass on heating- Lining)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Loss in mass on heating- Cover)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 23°C - Type 1)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 23°C - Type 2)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 23°C - Type 3)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 23°C - Type 1)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 23°C - Type 2)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 23°C - Type 3)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 60°C - Type 1)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 60°C - Type 2)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 60°C - Type 3)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 60°C - Type 1)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 60°C - Type 2)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 60°C - Type 3)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Change in Length at maximum working pressure at 23°C (±8%))	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Adhesion between components)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - UV resistance (Xenon-arc lamp))	-	0	-
7, 7.2 -Table 3(Flexibility at 23°C)	-	0	-
7, 7.2 -Table 3(Low Temperature flexibility)	-	0	-

15 Aug, 2028

-
Included w.e.f 15.01.2025

7851

Global Testing Laboratory Private limited, Ghaziabad

8184306

IS 694 (2010)

Polyvinyl chloride insulated unsheathed and sheathed cables/cords with rigid and flexible conductor for rated voltages up to and including 450/750 v (Fourth Revision)

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
13(Cable code)	-	500	-
11.2(Legibility)	-	500	-
11.1(Durability)	-	500	-
11(Identification)	-	500	-
10.9(Additional ageing test (OU cables only) -HV test (at 60±3oC))	-	3000	-
10.4(Flammability test- Unaffected portion)	-	1000	-
10.4(Flammability test-Burning after flame removal)	-	1000	-
table 1 e) 3) (IR constant- max. Temp)	-	1000	-
table 1 e) 3) (IR constant- Room temp )	-	1000	-
table 1 e) 3) (Volume Resistivity - Maximum temp)	-	1000	-
table 1 e) 3) (Volume Resistivity - Room temp )	-	1000	-
10.2(HV (room temperature))	-	1000	-
10.1(HV (water immersion))	-	2000	-
10.1(HV (water immersion))	-	2000	-
10.8(Smoke density rating)	-	2000	-
10.6(Halogen evolution)	-	2000	-
10.7(Temperature index)	-	2000	-
10.5(Oxygen index)	-	2000	-
Table 1 iii) d) 9)(Cold impact for sheath)	-	1000	-
Table 1 iii) d) 8)(Cold bend for sheath)	-	1000	-
Table 1 iii) c) 9)(Cold impact for insulation)	-	1000	-
Table 1 iii) c) 8)(Cold bend for insulation)	-	1000	-
Table 1(Category Code)	-	500	-
Table 1 iii) d) 7)(Thermal stability- Sheath )	-	1000	-
Table 1 iii) c) 7)(Thermal stability- Insulation )	-	2000	-
Table 1 iii) d) 6)(Hot deformation -Indentation depth - Sheath )	-	1000	-
Table 1 iii) c) 6)(Hot deformation - Indentation depth- Insulation)	-	1000	-
Table 1 iii) d) 5)(Heat shock-Sheath )	-	1000	-
Table 1 iii) c) 5)(Heat shock-Insulation )	-	1000	-
Table 1 iii) d) 4)(Cracks Observed)	-	1000	-
Table 1 iii) d) 4)(Shrinkage- Sheath )	-	1000	-
Table 1 iii) c) 4)(Cracks Observed)	-	1000	-
Table 1 iii) c) 4)(Shrinkage-Insulation)	-	1000	-
Table 1 iii) d) 2)(Loss of mass- Sheath )	-	2000	-
Table 1 iii) c) 2)(Loss of mass- Insulation )	-	2000	-
Table 1 iii) d) 3)(Sheath- Elongation variation)	-	2000	-
Table 1 iii) d) 3)(Sheath- TS variation)	-	2000	-
Table 1 iii) d) 3)(Sheath- Elongation (After ageing))	-	2000	-
Table 1 iii) d) 3)(Sheath- Tensile strength (After ageing))	-	2000	-
Table 1 iii) d) 1)(Sheath- Elongation (Without ageing))	-	1000	-
Table 1 iii) d) 1)(Sheath -Tensile strength (Without ageing))	-	1000	-
Table 1 iii) c) 3)(Elongation variation)	-	2000	-
Table 1 iii) c) 3)(TS variation)	-	2000	-
Table 1 iii) c) 3)(Elongation (After ageing))	-	2000	-
Table 1 iii) c) 3)(Tensile strength (After ageing))	-	2000	-
Table 1 iii) c) 1)(Elongation (Without ageing))	-	1000	-
Table 1 iii) c) 1)(Tensile strength (Without ageing))	-	1000	-
(Cl. 18.1.4) (Cl. 19.1.5) (Cl. 20.1.4) (Cl. 22.1.4)(Colour of Sheath)	-	500	-
8.3(Thickness of Sheath)	-	1000	-
5.2(Application )	-	500	-
5.3(Thickness of Insulation)	-	1000	-
9.1(Ovality)	-	1000	-
9(Overall dimensions)	-	500	-
10.11(Per sulphate test (for tinned Cu cable only))	-	1000	-
4.2(Conductor resistance test)	-	1000	-
4.1(Wrapping test (for Al))	-	1000	-
4.1(Tensile test (for Al)- After Stranding)	-	1000	-
4.1(Tensile test (for Al)-Before Stranding)	-	1000	-
4.1(Annealing test (for copper))	-	1000	-
(Cl.6.1.3 of IS 8130:2013)(Flexible Conductors (Classes 5))	-	500	-
(Cl.6.1.3 of IS 8130:2013)( Flexible Conductors (Classes 5))	-	500	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors(Class-2))	-	500	-
(Cl.6.1.3 of IS 8130:2013)(Stranded compacted circular conductors and shaped conductors (Class 2))	-	500	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors (Class-2))	-	500	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors (Class-2))	-	500	-
(Cl.6.1.3 of IS 8130:2013)(Solid Conductor (Class 1))	-	500	-
(Cl.6.1 of IS 8130:2013)(Solid Conductor (Class 1))	-	500	-
(Cl.6.1 of IS 8130:2013)(Solid Conductor (Class 1))	-	500	-
(Cl.16.1) (Cl.19.1)(Conductor- Diameter )	-	500	-
(Cl.16.1) (Cl.19.1)(Conductor)	-	500	-
(Cl.16.1) (Cl.19.1)(Conductor)	-	500	-
(Cl.16.1) (Cl.19.1)(Conductor)	-	500	-
(Cl. 18.1.3) (Cl. 19.1.4) (Cl. 20.1.3) (Cl. 21.1.3) (Cl. 22.1.3)(Assembly of cores )	-	500	-
12(CONSTRUCTION Core Identification)	-	500	-
8.1(Sheath Material )	-	500	-
7(Binder Tape)	-	500	-
6.2(Filler)	-	500	-
6.1(Filler)	-	500	-
5.1(Insulation)	-	500	-
4.4(Joints in Conductor)	-	500	-
4.4(Joints in Conductor)	-	500	-
4.1(Conductor - Material)	-	500	-
4.1(Conductor - Material)	-	500	-
10.11(Persulphate Test )	-	2000	-
12.0(Core identification)	-	500	-
4, IS 8130(Construction of conductor)	-	500	-
Table 2, IS 8130(No fo wire in a conductor)	-	500	-
8.3(Minimum thickness of Sheath)	-	1000	-
8.3(Avarage thickness of Sheath)	-	1000	-
5.3(Minimum thickness of insulation)	-	1000	-
5.3(Avarage thickness of insulation)	-	1000	-
table 1, 4.2(insulation resistance test)	-	1000	-
5.4(Mechanical properties before and after ageing)	-	2000	-
4.1(Material)	-	500	-
4.2(Electrical Resistance)	-	1000	-
5(INSULATION)	-	500	-
6(FILLER)	-	500	-
7(BINDER TAPE)	-	500	-
8(SHEATH)	-	500	-
9(OVERALL DIMENSIONS)	-	1000	-
10.1(High Voltage Test (Water Immersion Test))	-	2000	-
10.2(High Voltage Test (at Room Temperature))	-	1000	-
10.4(Flammability Test)	-	1000	-
10.5(Oxygen Index Test)	-	2000	-
10.6(Test for Halogen Acid Gas Evolution)	-	2000	-
10.7(Test for Temperature Index)	-	2000	-
10.8(Smoke Density Rating)	-	2000	-
10.9(Additional Ageing Test (for Cables for Outdoor Use)	-	2000	-
10.1(Flex Test)	-	1000	-
10.11(Persulphate Test)	-	1000	-
11(IDENTIFICATION)	-	500	-
12(CORE IDENTIFICATION)	-	500	-
13(CABLE CODE)	-	500	-
15(PACKING AND MARKING)	-	500	-
16.1(Construction)	-	500	-
16.2(Tests)	-	500	-
17(SINGLE CORE NON-SHEATHED CABLES WITH FLEXIBLE CONDUCTOR FOR GENERAL PURPOSE (MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C))	-	500	-
18(SINGLE AND MULTICORE CIRCULAR PVC INSULATED AND SHEATHED CABLES WITH RIGID CONDUCTOR (CLASS 1 AND CLASS 2) FOR GENERAL PURPOSE ) FOR MAXIMUM CONDUCTOR TEMPERATURE (70°C OR 85°C))	-	500	-
19(SINGLE AND MULTICORE CIRCULAR PVC INSULATED AND SHEATHED CABLES/CORDS WITH FLEXIBLE CONDUCTOR (CLASS 5) FOR GENERAL PURPOSE (MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C))	-	500	-
20(MULTICORE CIRCULAR PVC INSULATED AND SHEATHED CABLES WITH FLEXIBLE CONDUCTOR (CLASS 5) FOR GENERAL PURPOSE (FOR MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C))	-	500	-
21(ARALLEL TWIN AND TWISTED TWIN FLEXIBLE PVC INSULATED UNSHEATHED CORDS (CLASS 5) FOR GENERAL PURPOSE (FOR MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C))	-	500	-
22(TWO AND THREE CORE FLAT CABLES WITH PVC INSULATION AND SHEATHED (CLASS 2 OR 5) FOR GENERAL PURPOSE( FOR MAXIMUM CONDUCTOR TEMPERA TURE 70°C OR 85°C))	-	500	-
(4.3 of IS 8130:2013)(Form of Conductor)	-	500	-
( 4.4.1 of IS 8130:2013)(Joints in Conductor)	-	500	-
(4.4.2 of IS 8130:2013)(Joints in Conductor Solid Conductors (Aluminium Conductors only))	-	500	-
(Cl.6.1.1 of IS 8130:2013)(Solid Conductor (Class 1))	-	500	-
(Cl.6.1.2 of IS 8130:2013)(Solid Conductor (Class 1))	-	500	-
(Cl.6.1.3 of IS 8130:2013)(Solid Conductor (Class 1))	-	500	-
(6.2.1 of IS 8130:2013)(Stranded Circular Non-compacted Conductors (Class 2))	-	500	-
(6.2.2 of IS 8130:2013)(Stranded Circular Non-compacted Conductors (Class 2))	-	500	-
(6.2.3 of IS 8130:2013)(Stranded Circular Non-compacted Conductors (Class 2))	-	500	-
(6.3.1 of IS 8130:2013)(Stranded Compacted Circular Conductors and Shaped Conductors (Class 2))	-	500	-
(6.3.2 of IS 8130:2013)(Stranded Compacted Circular Conductors and Shaped Conductors (Class 2))	-	500	-
(6.3.3 of IS 8130:2013)(Stranded Compacted Circular Conductors and Shaped Conductors (Class 2))	-	500	-
( 6.4.1 of IS 8130:2013)(Flexible Conductors (Class 5))	-	500	-
(6.4.2 of IS 8130:2013)(Flexible Conductors (Class 5))	-	500	-
( 6.4.3 of IS 8130:2013)(Flexible Conductors (Class 5))	-	500	-
Cl.19.1.4(Assembly of Cores)	-	500	-
Cl. 8.2(Application of Sheath)	-	500	-
10.3(Spark Test)	-	1000	-
10.3(Spark test)	-	1000	-
Table 4(Copper purity test)	-	2500	-
10.3(Spark Test)	-	1000	-

11 Mar, 2028

-
-

7852

INDIAN TESTING LABORATORY PRIVATE LIMITED, GREATER NOIDA

8171306

IS 14756 (2022)

Draft Indian Standard STAINLESS STEEL COOKWARE SPECIFICATION Second Revision of IS 14756

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Material)	-	500	-
3.2(Material)	-	500	-
3.3(Material)	-	500	-
3.4(Material)	-	500	-
3.4(Material)	-	500	-
3.5(Material)	-	500	-
3.5(Material)	-	500	-
3.5(Material)	-	500	-
3.5(Material)	-	500	-
4.1 (Annex A)(Shapes and Dimensions)	-	100	-
4.2 (Table 1)(Shapes and Dimensions)	-	100	-
4.2 (Table 1)(Shapes and Dimensions)	-	100	-
4.2(Shapes and Dimensions)	-	100	-
4.3(Shapes and Dimensions)	-	100	-
4.4(Shapes and Dimensions)	-	100	-
5.1(Workmanship and Finish)	-	100	-
5.1(Workmanship and Finish)	-	100	-
5.1(Workmanship and Finish)	-	100	-
5.2(Workmanship and Finish)	-	100	-
5.3(Workmanship and Finish)	-	100	-
5.3(Workmanship and Finish)	-	100	-
5.3(Workmanship and Finish)	-	100	-
5.3(Workmanship and Finish)	-	100	-
5.3(Workmanship and Finish)	-	100	-
5.3(Workmanship and Finish)	-	100	-
5.4(Workmanship and Finish)	-	100	-
5.5(Workmanship and Finish)	-	100	-
5.6(Workmanship and Finish)	-	100	-
6.1(Staining Test)	-	1000	-
6.1(Staining Test)	-	1000	-
6.2(Mechanical Shock Test (For Cladded Utensils only))	-	1000	-
6.3(Thermal Shock Test (For Cladded Utensils only))	-	1000	-
6.4(Dry Heat Test (For Cladded Utensils only))	-	1000	-
6.5(Coating Thickness Test (For Copper Deposit))	-	1000	-
6.6(3 Ply)	-	1000	-
6.7.1(Nominal Capacity Test)	-	1000	-
6.7.2(Nominal Capacity Test- Diameter)	-	1000	-
6.8.1(Tests on Tempered Glass Lid)	-	1000	-
6.8.1(Tests on Tempered Glass Lid)	-	1000	-
6.8.2(Tests on Tempered Glass Lid (Ball drop test))	-	1000	-
6.8.3(Tests on Tempered Glass Lid (thermal shock test))	-	1000	-
6.8.4.1(Tests on Tempered Glass Lid (Free Fall Test with rim facing down))	-	1000	-
6.8.4.2(Tests on Tempered Glass Lid (Free Fall Test without rim facing down))	-	1000	-
As per Clause 3(Carbon)	-	500	-
As per Clause 3(Silicon)	-	500	-
As per Clause 3(Manganese)	-	500	-
As per Clause 3(Nickel)	-	500	-
As per Clause 3(Chromium)	-	500	-
As per Clause 3(Sulphur)	-	500	-
As per Clause 3(phosphorus)	-	500	-
As per Clause 3(Nitrogen)	-	500	-
As per Clause 3(Titanium)	-	500	-
As per Clause 3(Aluminium)	-	500	-
As per Clause 3(Copper)	-	500	-
As per Clause 3(Magnesium)	-	500	-
As per Clause 3(Iron)	-	500	-
As per Clause 3(Zinc)	-	500	-
As per Clause 3(Arsenic)	-	500	-
As per Clause 3(Antimony)	-	500	-
As per Clause 3(Bismith)	-	500	-
As per Clause 3(Lead)	-	500	-
As per Clause 3(Tellurium)	-	500	-
CL-5.4(CL-4.1 of IS 13395)(Construction)	-	100	-
CL-5.4(CL-4.2 of IS 13395)(Materials)	-	100	-
CL-5.4(CL-4.3 of IS 13395)(Selection and Size)	-	100	-
CL-5.4(CL-4.4 of IS 13395)("Position of Handle and Knob with Respect to Cookware")	-	100	-
CL_5.4(CL-4.5 of IS 13395)(Attachment to Cookware)	-	100	-
CL-5.4(CL-5.2 of IS 13395)(Bending Strength)	-	100	-
CL-5.4(CL-5.3 of IS 13395)(Torque Strength)	-	100	-
CL-5.4(CL-5.4 of IS 13395)(Impact Strength)	-	100	-
CL-5.4(CL-5.5 of IS 13395)(Fatigue Resistance)	-	100	-
CL-5.4(CL-5.6 of IS 13395)(Leakage)	-	100	-
CL-5.4(CL-5.7 of IS 13395)(Thermal Insulation)	-	100	-
CL-5.4(CL-5.8 of IS 13395)(Heat Resistance)	-	100	-
CL-5.4(CL-5.9 of IS 13395)(Washing Resistance (Type Test))	-	100	-
CL-5.4(CL-5.10 of IS 13395)(Burning Resistance)	-	100	-
3.1(Material)	-	0	-
3.2(Material)	-	0	-
3.3(Material)	-	0	-
3.4(Material)	-	0	-
3.4(Material)	-	0	-
3.5(Material)	-	0	-
3.5(Material)	-	0	-
3.5(Material)	-	0	-
3.5(Material)	-	0	-
4.1 (Annex A)(Shapes and Dimensions)	-	0	-
4.2 (Table 1)(Shapes and Dimensions)	-	0	-
4.2 (Table 1)(Shapes and Dimensions)	-	0	-
4.2(Shapes and Dimensions)	-	0	-
4.3(Shapes and Dimensions)	-	0	-
4.4(Shapes and Dimensions)	-	0	-
5.1(Workmanship and Finish)	-	0	-
5.1(Workmanship and Finish)	-	0	-
5.1(Workmanship and Finish)	-	0	-
5.2(Workmanship and Finish)	-	0	-
5.3(Workmanship and Finish)	-	0	-
5.3(Workmanship and Finish)	-	0	-
5.3(Workmanship and Finish)	-	0	-
5.3(Workmanship and Finish)	-	0	-
5.3(Workmanship and Finish)	-	0	-
5.3(Workmanship and Finish)	-	0	-
5.4(Workmanship and Finish)	-	0	-
5.5(Workmanship and Finish)	-	0	-
5.6(Workmanship and Finish)	-	0	-
6.1(Staining Test)	-	0	-
6.1(Staining Test)	-	0	-
6.2(Mechanical Shock Test (For Cladded Utensils only))	-	0	-
6.3(Thermal Shock Test (For Cladded Utensils only))	-	0	-
6.4(Dry Heat Test (For Cladded Utensils only))	-	0	-
6.5(Coating Thickness Test (For Copper Deposit))	-	0	-
6.6(3 Ply)	-	0	-
6.7.1(Nominal Capacity Test)	-	0	-
6.7.2(Nominal Capacity Test- Diameter)	-	0	-
6.8.1(Tests on Tempered Glass Lid)	-	0	-
6.8.1(Tests on Tempered Glass Lid)	-	0	-
6.8.2(Tests on Tempered Glass Lid (Ball drop test))	-	0	-
6.8.3(Tests on Tempered Glass Lid (thermal shock test))	-	0	-
6.8.4.1(Tests on Tempered Glass Lid (Free Fall Test with rim facing down))	-	0	-
6.8.4.2(Tests on Tempered Glass Lid (Free Fall Test without rim facing down))	-	0	-
As per Clause 3(Carbon)	-	0	-
As per Clause 3(Silicon)	-	0	-
As per Clause 3(Manganese)	-	0	-
As per Clause 3(Nickel)	-	0	-
As per Clause 3(Chromium)	-	0	-
As per Clause 3(Sulphur)	-	0	-
As per Clause 3(phosphorus)	-	0	-
As per Clause 3(Nitrogen)	-	0	-
As per Clause 3(Titanium)	-	0	-
As per Clause 3(Aluminium)	-	0	-
As per Clause 3(Copper)	-	0	-
As per Clause 3(Magnesium)	-	0	-
As per Clause 3(Iron)	-	0	-
As per Clause 3(Zinc)	-	0	-
As per Clause 3(Arsenic)	-	0	-
As per Clause 3(Antimony)	-	0	-
As per Clause 3(Bismith)	-	0	-
As per Clause 3(Lead)	-	0	-
As per Clause 3(Tellurium)	-	0	-
CL-5.4(CL-4.1 of IS 13395)(Construction)	-	0	-
CL-5.4(CL-4.2 of IS 13395)(Materials)	-	0	-
CL-5.4(CL-4.3 of IS 13395)(Selection and Size)	-	0	-
CL-5.4(CL-4.4 of IS 13395)("Position of Handle and Knob with Respect to Cookware")	-	0	-
CL_5.4(CL-4.5 of IS 13395)(Attachment to Cookware)	-	0	-
CL-5.4(CL-5.2 of IS 13395)(Bending Strength)	-	0	-
CL-5.4(CL-5.3 of IS 13395)(Torque Strength)	-	0	-
CL-5.4(CL-5.4 of IS 13395)(Impact Strength)	-	0	-
CL-5.4(CL-5.5 of IS 13395)(Fatigue Resistance)	-	0	-
CL-5.4(CL-5.6 of IS 13395)(Leakage)	-	0	-
CL-5.4(CL-5.7 of IS 13395)(Thermal Insulation)	-	0	-
CL-5.4(CL-5.8 of IS 13395)(Heat Resistance)	-	0	-
CL-5.4(CL-5.9 of IS 13395)(Washing Resistance (Type Test))	-	0	-
CL-5.4(CL-5.10 of IS 13395)(Burning Resistance)	-	0	-
3.1(Material)	-	0	-
3.2(Material)	-	0	-
3.3(Material)	-	0	-
3.4(Material)	-	0	-
3.4(Material)	-	0	-
3.5(Material)	-	0	-
3.5(Material)	-	0	-
3.5(Material)	-	0	-
3.5(Material)	-	0	-
4.1 (Annex A)(Shapes and Dimensions)	-	0	-
4.2 (Table 1)(Shapes and Dimensions)	-	0	-
4.2 (Table 1)(Shapes and Dimensions)	-	0	-
4.2(Shapes and Dimensions)	-	0	-
4.3(Shapes and Dimensions)	-	0	-
4.4(Shapes and Dimensions)	-	0	-
5.1(Workmanship and Finish)	-	0	-
5.1(Workmanship and Finish)	-	0	-
5.1(Workmanship and Finish)	-	0	-
5.2(Workmanship and Finish)	-	0	-
5.3(Workmanship and Finish)	-	0	-
5.3(Workmanship and Finish)	-	0	-
5.3(Workmanship and Finish)	-	0	-
5.3(Workmanship and Finish)	-	0	-
5.3(Workmanship and Finish)	-	0	-
5.3(Workmanship and Finish)	-	0	-
5.4(Workmanship and Finish)	-	0	-
5.5(Workmanship and Finish)	-	0	-
5.6(Workmanship and Finish)	-	0	-
6.1(Staining Test)	-	0	-
6.1(Staining Test)	-	0	-
6.2(Mechanical Shock Test (For Cladded Utensils only))	-	0	-
6.3(Thermal Shock Test (For Cladded Utensils only))	-	0	-
6.4(Dry Heat Test (For Cladded Utensils only))	-	0	-
6.5(Coating Thickness Test (For Copper Deposit))	-	0	-
6.6(3 Ply)	-	0	-
6.7.1(Nominal Capacity Test)	-	0	-
6.7.2(Nominal Capacity Test- Diameter)	-	0	-
6.8.1(Tests on Tempered Glass Lid)	-	0	-
6.8.1(Tests on Tempered Glass Lid)	-	0	-
6.8.2(Tests on Tempered Glass Lid (Ball drop test))	-	0	-
6.8.3(Tests on Tempered Glass Lid (thermal shock test))	-	0	-
6.8.4.1(Tests on Tempered Glass Lid (Free Fall Test with rim facing down))	-	0	-
6.8.4.2(Tests on Tempered Glass Lid (Free Fall Test without rim facing down))	-	0	-
As per Clause 3(Carbon)	-	0	-
As per Clause 3(Silicon)	-	0	-
As per Clause 3(Manganese)	-	0	-
As per Clause 3(Nickel)	-	0	-
As per Clause 3(Chromium)	-	0	-
As per Clause 3(Sulphur)	-	0	-
As per Clause 3(phosphorus)	-	0	-
As per Clause 3(Nitrogen)	-	0	-
As per Clause 3(Titanium)	-	0	-
As per Clause 3(Aluminium)	-	0	-
As per Clause 3(Copper)	-	0	-
As per Clause 3(Magnesium)	-	0	-
As per Clause 3(Iron)	-	0	-
As per Clause 3(Zinc)	-	0	-
As per Clause 3(Arsenic)	-	0	-
As per Clause 3(Antimony)	-	0	-
As per Clause 3(Bismith)	-	0	-
As per Clause 3(Lead)	-	0	-
As per Clause 3(Tellurium)	-	0	-
CL-5.4(CL-4.1 of IS 13395)(Construction)	-	0	-
CL-5.4(CL-4.2 of IS 13395)(Materials)	-	0	-
CL-5.4(CL-4.3 of IS 13395)(Selection and Size)	-	0	-
CL-5.4(CL-4.4 of IS 13395)("Position of Handle and Knob with Respect to Cookware")	-	0	-
CL_5.4(CL-4.5 of IS 13395)(Attachment to Cookware)	-	0	-
CL-5.4(CL-5.2 of IS 13395)(Bending Strength)	-	0	-
CL-5.4(CL-5.3 of IS 13395)(Torque Strength)	-	0	-
CL-5.4(CL-5.4 of IS 13395)(Impact Strength)	-	0	-
CL-5.4(CL-5.5 of IS 13395)(Fatigue Resistance)	-	0	-
CL-5.4(CL-5.6 of IS 13395)(Leakage)	-	0	-
CL-5.4(CL-5.7 of IS 13395)(Thermal Insulation)	-	0	-
CL-5.4(CL-5.8 of IS 13395)(Heat Resistance)	-	0	-
CL-5.4(CL-5.9 of IS 13395)(Washing Resistance (Type Test))	-	0	-
CL-5.4(CL-5.10 of IS 13395)(Burning Resistance)	-	0	-

15 Aug, 2028

-
Included w.e.f 07.01.2025

7853

INDIAN TESTING LABORATORY PRIVATE LIMITED, GREATER NOIDA

8171306

IS 9573 : Part 2 (2017)

Rubber hose for liquefied petroleum gas (Lpg) - Specification: Part 2 domestic and commercial application (Fourth Revision)

14500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4.1(General)	-	200	-
Clause 4.2(Material)	-	200	-
Clause 4.2.1(Lining)	-	200	-
Clause 4.2.2 (a)(Reinforcement)	-	500	-
Clause 4.2.2 (b)(Reinforcement)	-	500	-
Clause 4.2.3(Cover)	-	500	-
Clause 4.3 Sub Clause 4.3.1 Table 1(Bore Size)	-	500	-
Clause 4.3 Sub Clause 4.3.2 (a)(Thickness of Lining and Cover)	-	500	-
Clause 4.3 Sub Clause 4.3.2 (b)(Thickness of Lining and Cover)	-	500	-
Clause 4.3 Sub Clause 4.3.3(Length)	-	500	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (i) (a)(Tensile Strength- Lining)	-	1000	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (i) (b)(Tensile Strength- cover)	-	1000	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (ii) (a)(Elongation at break- Lining)	-	1000	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (ii) (b)(Elongation at break- Cover)	-	1000	-
Clause 4.4 Sub Clause 4.4.2 (a)(Accelerated Ageing Test lining)	-	1000	-
Clause 4.4 Sub Clause 4.4.2 (b)(Accelerated Ageing Test lining)	-	1000	-
Clause 4.4 Sub Clause 4.4.2 (a)(Accelerated Ageing Test cover)	-	1000	-
Clause 4.4 Sub Clause 4.4.2 (b)(Accelerated Ageing Test cover)	-	1000	-
Clause 4.4 Sub Clause 4.4.3 (a)(Resistance of Lining to n-pentane)	-	1200	-
Clause 4.4 Sub Clause 4.4.3 (b)(Resistance of Lining to n-pentane)	-	1200	-
Clause 4.5 Sub clause 4.5.1(Adhesion)	-	1000	-
Clause 4.5 Sub clause 4.5.2(Low Temperature Flexibility)	-	1000	-
Clause 4.5 Sub clause 4.5.3(Flexibility of Hose)	-	1000	-
Clause 4.5 Sub clause 4.5.4(Ozone Resistance)	-	2000	-
Clause 4.5 Sub clause 4.5.5 4.5.5.1(Proof pressure test)	-	1000	-
Clause 4.5 Sub clause 4.5.5 4.5.5.2(Bursting pressure)	-	1000	-
Clause 4.5 Sub clause 4.5.6(Grip Strength Test)	-	1000	-
Clause 4.5 Sub clause 4.5.7(Burning Behaviour)	-	1000	-
Clause 5.2 (a)(Marking Manufacturer’s name or trade-mark, if any )	-	200	-
Clause 5.2 (b)(Marking Words LPG, Max W.P. 1.0 MPa; )	-	200	-
Clause 5.2 (c)(Marking Nominal bore, 1000111)	-	200	-
Clause 5.2 (d)(Marking Batch/Lot No. )	-	200	-
Clause 5.2 (e)(Marking Month and year of manufacture )	-	200	-
Clause 5.2 (f)(Marking IS 9573 (Part 2) )	-	200	-
Clause 5.2 (f)(Marking ecommended to replace before (MONTH/YEAR) )	-	200	-
Clause 5.2.1(BIS Certification Marking )	-	200	-

15 Aug, 2028

-
Included w.e.f. 12.12.2024

7854

INDIAN TESTING LABORATORY PRIVATE LIMITED, GREATER NOIDA

8171306

IS 9573 : Part 1 (2017)

Rubber hose for liquefied petroleum gas (Lpg) - Specification: Part 1 industrial application (Fourth Revision)

14800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4.1 (General)	-	200	-
Clause 4.1 (General)	-	200	-
Clause 4.1(General)	-	200	-
Clause 4.2(Material)	-	500	-
Clause 4.2.1(Lining)	-	500	-
Clause 4.2.2(Reinforcement)	-	500	-
Clause 4.2.3(Cover)	-	500	-
Clause 4.3 Sub Clause 4.3.1 Table 1(Bore Size)	-	500	-
Clause 4.3 Sub Clause 4.3.2 (a)(Thickness of Lining and Cover)	-	500	-
Clause 4.3 Sub Clause 4.3.2 (b)(Thickness of Lining and Cover)	-	500	-
Clause 4.3 Sub Clause 4.3.3(Length)	-	500	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (i) (a)(Tensile Strength- Lining)	-	1000	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (i) (b)(Tensile Strength- cover)	-	1000	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (ii) (a)(Elongation at break- Lining)	-	1000	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (ii) (b)(Elongation at break- cover)	-	1000	-
Clause 4.4 Sub Clause 4.4.2 (a)(Accelerated Ageing Test lining)	-	1000	-
Clause 4.4 Sub Clause 4.4.2 (b)(Accelerated Ageing Test lining)	-	1000	-
Clause 4.4 Sub Clause 4.4.2 (a)(Accelerated Ageing Test cover)	-	1000	-
Clause 4.4 Sub Clause 4.4.2 (b)(Accelerated Ageing Test cover)	-	1000	-
Clause 4.4 Sub Clause 4.4.3 (a)(Resistance of Lining to n-pentane)	-	1200	-
Clause 4.4 Sub Clause 4.4.3 (b)(Resistance of Lining to n-pentane)	-	1200	-
Clause 4.5 Sub clause 4.5.1(Adhesion)	-	1000	-
Clause 4.5 Sub clause 4.5.2(Low Temperature Flexibility)	-	1000	-
Clause 4.5 Sub clause 4.5.3(Flexibility of Hose)	-	1000	-
Clause 4.5 Sub clause 4.5.4(Ozone Resistance)	-	2000	-
Clause 4.5 Sub clause 4.5.5 4.5.5.1(Proof pressure test)	-	1000	-
Clause 4.5 Sub clause 4.5.5 4.5.5.2(Bursting pressure)	-	1000	-
Clause 4.5 Sub clause 4.5.6(Electrical Continuity Test)	-	1000	-
Clause 4.5 Sub clause 4.5.7(Burning Behaviour)	-	1000	-
Clause 5.2 (a)(Marking Manufacturer’s name or trade-mark, if any )	-	200	-
Clause 5.2 (b)(Marking Words LPG, Max W.P. 2.5 MPa; )	-	200	-
Clause 5.2 (c)(Marking Nominal bore )	-	200	-
Clause 5.2 (d)(Marking Batch/Lot No. )	-	200	-
Clause 5.2 (e)(Marking Month and year of manufacture )	-	200	-
Clause 5.2 (f)(Marking IS 9573 (Part 1) )	-	200	-
Clause 5.2.1(BIS Certification Marking )	-	200	-

15 Aug, 2028

-
Included w.e.f 18.12.2024

7855

LILABA ANALYTICAL LABORATORIES LLP, SURAT

7137216

IS 15410 (2025)

PLASTIC BOTTLES/CONTAINERS FOR PACKAGING OF NATURAL MINERAL WATER AND PACKAGED DRINKING WATER - SPECIFICATION (first revision)

11700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4.1.1(Materials for Primary Packaging (Container))	-	300	-
Clause 4.1.2.1(Material for Closures (a) Closure materials (Aluminium))	-	0	-
Clause 4.1.2.1(Material for Closures (b) Plastic Materials)	-	0	-
Clause 4.1.2.1(Material for Closures (c) Combination of plastics and metal)	-	0	-
Clause 4.1.2.2(Materials for Primary Packaging-Closure colourants)	-	0	-
Clause 4.1.2.3(Materials for Primary Packaging-Sleeves for the closure)	-	300	-
Clause 4.1.3(Materials for Primary Packaging-Wad)	-	100	-
Clause 4.2(Design, Shape and Dimensions)	-	100	-
Clause 4.3("Manufacture, Workmanship, Finish and Appearance")	-	100	-
Clause 4.4(Capacity (Nominal))	-	100	-
Clause 4.4(Capacity (Brimfull))	-	200	-
Clause 4.5(Wall Thickness Top)	-	100	-
Clause 4.5(Wall Thickness Middle)	-	100	-
Clause 4.5(Wall Thickness Bottom)	-	100	-
Clause 4.6.1.1(Colour-Transparency)	-	250	-
Clause 4.6.1.2(Colour-Tint)	-	0	-
Clause 4.6.2(Leakage Test (Closure Leakage) cls. 6.1 of IS 2798)	-	200	-
Clause 4.6.2(Leakage Test (Vibration Leakage) cls. 6.2 of IS 2798)	-	200	-
Clause 4.6.3.1(Drop Impact test)	-	200	-
Clause 4.6.3.2(Stack Load test)	-	250	-
Clause 4.6.4.1(Overall Migration Container)	-	500	-
Clause 4.6.4.1(Overall Migration Closure)	-	500	-
Clause 4.6.4.2(Specific Migration Container Barium)	-	250	-
Clause 4.6.4.2(Specific Migration Container Cobalt)	-	250	-
Clause 4.6.4.2(Specific Migration Container Copper)	-	250	-
Clause 4.6.4.2(Specific Migration Container Iron)	-	250	-
Clause 4.6.4.2(Specific Migration Container Lithium)	-	250	-
Clause 4.6.4.2(Specific Migration Container Manganese)	-	250	-
Clause 4.6.4.2(Specific Migration Container Zinc)	-	250	-
Clause 4.6.4.2(Specific Migration Container Antimony)	-	350	-
Clause 4.6.4.2(Specific Migration Container Phthalic acid, bis (2- ethylhexyl) ester (DEHP))	-	1000	-
Clause 4.6.4.2(Specific Migration Closure Barium)	-	250	-
Clause 4.6.4.2(Specific Migration Closure Cobalt)	-	250	-
Clause 4.6.4.2(Specific Migration Closure Copper)	-	250	-
Clause 4.6.4.2(Specific Migration Closure Iron)	-	250	-
Clause 4.6.4.2(Specific Migration Closure Lithium)	-	250	-
Clause 4.6.4.2(Specific Migration Closure Manganese)	-	250	-
Clause 4.6.4.2(Specific Migration Closure Zinc)	-	250	-
Clause 4.6.4.2(Specific Migration Closure Antimony)	-	350	-
Clause 4.6.4.2(Specific Migration Closure Phthalic acid, bis (2- ethylhexyl) ester (DEHP))	-	1000	-
Clause 4.6.4.3(Colour migration Container)	-	400	-
Clause 4.6.4.3(Colour migration Closure)	-	400	-
Clause 4.6.5(Water Potability Test (Taste))	-	500	-
Clause 4.6.5(Water Potability Test (odour))	-	500	-
Clause 5.1(Marking)	-	100	-
Clause 4.1.1(Materials for Primary Packaging (Container))	-	0	-
Clause 4.1.2.1(Material for Closures (a) Closure materials (Aluminium))	-	0	-
Clause 4.1.2.1(Material for Closures (b) Plastic Materials)	-	0	-
Clause 4.1.2.1(Material for Closures (c) Combination of plastics and metal)	-	0	-
Clause 4.1.2.2(Materials for Primary Packaging-Closure colourants)	-	0	-
Clause 4.1.2.3(Materials for Primary Packaging-Sleeves for the closure)	-	0	-
Clause 4.1.3(Materials for Primary Packaging-Wad)	-	0	-
Clause 4.2(Design, Shape and Dimensions)	-	0	-
Clause 4.3("Manufacture, Workmanship, Finish and Appearance")	-	0	-
Clause 4.4(Capacity (Nominal))	-	0	-
Clause 4.4(Capacity (Brimfull))	-	0	-
Clause 4.5(Wall Thickness Top)	-	0	-
Clause 4.5(Wall Thickness Middle)	-	0	-
Clause 4.5(Wall Thickness Bottom)	-	0	-
Clause 4.6.1.1(Colour-Transparency)	-	0	-
Clause 4.6.1.2(Colour-Tint)	-	0	-
Clause 4.6.2(Leakage Test (Closure Leakage) cls. 6.1 of IS 2798)	-	0	-
Clause 4.6.2(Leakage Test (Vibration Leakage) cls. 6.2 of IS 2798)	-	0	-
Clause 4.6.3.1(Drop Impact test)	-	0	-
Clause 4.6.3.2(Stack Load test)	-	0	-
Clause 4.6.4.1(Overall Migration Container)	-	0	-
Clause 4.6.4.1(Overall Migration Closure)	-	0	-
Clause 4.6.4.2(Specific Migration Container Barium)	-	0	-
Clause 4.6.4.2(Specific Migration Container Cobalt)	-	0	-
Clause 4.6.4.2(Specific Migration Container Copper)	-	0	-
Clause 4.6.4.2(Specific Migration Container Iron)	-	0	-
Clause 4.6.4.2(Specific Migration Container Lithium)	-	0	-
Clause 4.6.4.2(Specific Migration Container Manganese)	-	0	-
Clause 4.6.4.2(Specific Migration Container Zinc)	-	0	-
Clause 4.6.4.2(Specific Migration Container Antimony)	-	0	-
Clause 4.6.4.2(Specific Migration Container Phthalic acid, bis (2- ethylhexyl) ester (DEHP))	-	0	-
Clause 4.6.4.2(Specific Migration Closure Barium)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Cobalt)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Copper)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Iron)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Lithium)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Manganese)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Zinc)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Antimony)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Phthalic acid, bis (2- ethylhexyl) ester (DEHP))	-	0	-
Clause 4.6.4.3(Colour migration Container)	-	0	-
Clause 4.6.4.3(Colour migration Closure)	-	0	-
Clause 4.6.5(Water Potability Test (Taste))	-	0	-
Clause 4.6.5(Water Potability Test (odour))	-	0	-
Clause 5.1(Marking)	-	0	-
Clause 4.1.1(Materials for Primary Packaging (Container))	-	0	-
Clause 4.1.2.1(Material for Closures (a) Closure materials (Aluminium))	-	0	-
Clause 4.1.2.1(Material for Closures (b) Plastic Materials)	-	0	-
Clause 4.1.2.1(Material for Closures (c) Combination of plastics and metal)	-	0	-
Clause 4.1.2.2(Materials for Primary Packaging-Closure colourants)	-	0	-
Clause 4.1.2.3(Materials for Primary Packaging-Sleeves for the closure)	-	0	-
Clause 4.1.3(Materials for Primary Packaging-Wad)	-	0	-
Clause 4.2(Design, Shape and Dimensions)	-	0	-
Clause 4.3("Manufacture, Workmanship, Finish and Appearance")	-	0	-
Clause 4.4(Capacity (Nominal))	-	0	-
Clause 4.4(Capacity (Brimfull))	-	0	-
Clause 4.5(Wall Thickness Top)	-	0	-
Clause 4.5(Wall Thickness Middle)	-	0	-
Clause 4.5(Wall Thickness Bottom)	-	0	-
Clause 4.6.1.1(Colour-Transparency)	-	0	-
Clause 4.6.1.2(Colour-Tint)	-	0	-
Clause 4.6.2(Leakage Test (Closure Leakage) cls. 6.1 of IS 2798)	-	0	-
Clause 4.6.2(Leakage Test (Vibration Leakage) cls. 6.2 of IS 2798)	-	0	-
Clause 4.6.3.1(Drop Impact test)	-	0	-
Clause 4.6.3.2(Stack Load test)	-	0	-
Clause 4.6.4.1(Overall Migration Container)	-	0	-
Clause 4.6.4.1(Overall Migration Closure)	-	0	-
Clause 4.6.4.2(Specific Migration Container Barium)	-	0	-
Clause 4.6.4.2(Specific Migration Container Cobalt)	-	0	-
Clause 4.6.4.2(Specific Migration Container Copper)	-	0	-
Clause 4.6.4.2(Specific Migration Container Iron)	-	0	-
Clause 4.6.4.2(Specific Migration Container Lithium)	-	0	-
Clause 4.6.4.2(Specific Migration Container Manganese)	-	0	-
Clause 4.6.4.2(Specific Migration Container Zinc)	-	0	-
Clause 4.6.4.2(Specific Migration Container Antimony)	-	0	-
Clause 4.6.4.2(Specific Migration Container Phthalic acid, bis (2- ethylhexyl) ester (DEHP))	-	0	-
Clause 4.6.4.2(Specific Migration Closure Barium)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Cobalt)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Copper)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Iron)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Lithium)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Manganese)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Zinc)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Antimony)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Phthalic acid, bis (2- ethylhexyl) ester (DEHP))	-	0	-
Clause 4.6.4.3(Colour migration Container)	-	0	-
Clause 4.6.4.3(Colour migration Closure)	-	0	-
Clause 4.6.5(Water Potability Test (Taste))	-	0	-
Clause 4.6.5(Water Potability Test (odour))	-	0	-
Clause 5.1(Marking)	-	0	-
Clause 4.1.1(Materials for Primary Packaging (Container))	-	0	-
Clause 4.1.2.1(Material for Closures (a) Closure materials (Aluminium))	-	0	-
Clause 4.1.2.1(Material for Closures (b) Plastic Materials)	-	0	-
Clause 4.1.2.1(Material for Closures (c) Combination of plastics and metal)	-	0	-
Clause 4.1.2.2(Materials for Primary Packaging-Closure colourants)	-	0	-
Clause 4.1.2.3(Materials for Primary Packaging-Sleeves for the closure)	-	0	-
Clause 4.1.3(Materials for Primary Packaging-Wad)	-	0	-
Clause 4.2(Design, Shape and Dimensions)	-	0	-
Clause 4.3("Manufacture, Workmanship, Finish and Appearance")	-	0	-
Clause 4.4(Capacity (Nominal))	-	0	-
Clause 4.4(Capacity (Brimfull))	-	0	-
Clause 4.5(Wall Thickness Top)	-	0	-
Clause 4.5(Wall Thickness Middle)	-	0	-
Clause 4.5(Wall Thickness Bottom)	-	0	-
Clause 4.6.1.1(Colour-Transparency)	-	0	-
Clause 4.6.1.2(Colour-Tint)	-	0	-
Clause 4.6.2(Leakage Test (Closure Leakage) cls. 6.1 of IS 2798)	-	0	-
Clause 4.6.2(Leakage Test (Vibration Leakage) cls. 6.2 of IS 2798)	-	0	-
Clause 4.6.3.1(Drop Impact test)	-	0	-
Clause 4.6.3.2(Stack Load test)	-	0	-
Clause 4.6.4.1(Overall Migration Container)	-	0	-
Clause 4.6.4.1(Overall Migration Closure)	-	0	-
Clause 4.6.4.2(Specific Migration Container Barium)	-	0	-
Clause 4.6.4.2(Specific Migration Container Cobalt)	-	0	-
Clause 4.6.4.2(Specific Migration Container Copper)	-	0	-
Clause 4.6.4.2(Specific Migration Container Iron)	-	0	-
Clause 4.6.4.2(Specific Migration Container Lithium)	-	0	-
Clause 4.6.4.2(Specific Migration Container Manganese)	-	0	-
Clause 4.6.4.2(Specific Migration Container Zinc)	-	0	-
Clause 4.6.4.2(Specific Migration Container Antimony)	-	0	-
Clause 4.6.4.2(Specific Migration Container Phthalic acid, bis (2- ethylhexyl) ester (DEHP))	-	0	-
Clause 4.6.4.2(Specific Migration Closure Barium)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Cobalt)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Copper)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Iron)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Lithium)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Manganese)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Zinc)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Antimony)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Phthalic acid, bis (2- ethylhexyl) ester (DEHP))	-	0	-
Clause 4.6.4.3(Colour migration Container)	-	0	-
Clause 4.6.4.3(Colour migration Closure)	-	0	-
Clause 4.6.5(Water Potability Test (Taste))	-	0	-
Clause 4.6.5(Water Potability Test (odour))	-	0	-
Clause 5.1(Marking)	-	0	-
Clause 4.1.1(Materials for Primary Packaging (Container))	-	0	-
Clause 4.1.2.1(Material for Closures (a) Closure materials (Aluminium))	-	0	-
Clause 4.1.2.1(Material for Closures (b) Plastic Materials)	-	0	-
Clause 4.1.2.1(Material for Closures (c) Combination of plastics and metal)	-	0	-
Clause 4.1.2.2(Materials for Primary Packaging-Closure colourants)	-	0	-
Clause 4.1.2.3(Materials for Primary Packaging-Sleeves for the closure)	-	0	-
Clause 4.1.3(Materials for Primary Packaging-Wad)	-	0	-
Clause 4.2(Design, Shape and Dimensions)	-	0	-
Clause 4.3("Manufacture, Workmanship, Finish and Appearance")	-	0	-
Clause 4.4(Capacity (Nominal))	-	0	-
Clause 4.4(Capacity (Brimfull))	-	0	-
Clause 4.5(Wall Thickness Top)	-	0	-
Clause 4.5(Wall Thickness Middle)	-	0	-
Clause 4.5(Wall Thickness Bottom)	-	0	-
Clause 4.6.1.1(Colour-Transparency)	-	0	-
Clause 4.6.1.2(Colour-Tint)	-	0	-
Clause 4.6.2(Leakage Test (Closure Leakage) cls. 6.1 of IS 2798)	-	0	-
Clause 4.6.2(Leakage Test (Vibration Leakage) cls. 6.2 of IS 2798)	-	0	-
Clause 4.6.3.1(Drop Impact test)	-	0	-
Clause 4.6.3.2(Stack Load test)	-	0	-
Clause 4.6.4.1(Overall Migration Container)	-	0	-
Clause 4.6.4.1(Overall Migration Closure)	-	0	-
Clause 4.6.4.2(Specific Migration Container Barium)	-	0	-
Clause 4.6.4.2(Specific Migration Container Cobalt)	-	0	-
Clause 4.6.4.2(Specific Migration Container Copper)	-	0	-
Clause 4.6.4.2(Specific Migration Container Iron)	-	0	-
Clause 4.6.4.2(Specific Migration Container Lithium)	-	0	-
Clause 4.6.4.2(Specific Migration Container Manganese)	-	0	-
Clause 4.6.4.2(Specific Migration Container Zinc)	-	0	-
Clause 4.6.4.2(Specific Migration Container Antimony)	-	0	-
Clause 4.6.4.2(Specific Migration Container Phthalic acid, bis (2- ethylhexyl) ester (DEHP))	-	0	-
Clause 4.6.4.2(Specific Migration Closure Barium)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Cobalt)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Copper)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Iron)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Lithium)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Manganese)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Zinc)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Antimony)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Phthalic acid, bis (2- ethylhexyl) ester (DEHP))	-	0	-
Clause 4.6.4.3(Colour migration Container)	-	0	-
Clause 4.6.4.3(Colour migration Closure)	-	0	-
Clause 4.6.5(Water Potability Test (Taste))	-	0	-
Clause 4.6.5(Water Potability Test (odour))	-	0	-
Clause 5.1(Marking)	-	0	-
Clause 4.1.1(Materials for Primary Packaging (Container))	-	0	-
Clause 4.1.2.1(Material for Closures (a) Closure materials (Aluminium))	-	0	-
Clause 4.1.2.1(Material for Closures (b) Plastic Materials)	-	0	-
Clause 4.1.2.1(Material for Closures (c) Combination of plastics and metal)	-	0	-
Clause 4.1.2.2(Materials for Primary Packaging-Closure colourants)	-	0	-
Clause 4.1.2.3(Materials for Primary Packaging-Sleeves for the closure)	-	0	-
Clause 4.1.3(Materials for Primary Packaging-Wad)	-	0	-
Clause 4.2(Design, Shape and Dimensions)	-	0	-
Clause 4.3("Manufacture, Workmanship, Finish and Appearance")	-	0	-
Clause 4.4(Capacity (Nominal))	-	0	-
Clause 4.4(Capacity (Brimfull))	-	0	-
Clause 4.5(Wall Thickness Top)	-	0	-
Clause 4.5(Wall Thickness Middle)	-	0	-
Clause 4.5(Wall Thickness Bottom)	-	0	-
Clause 4.6.1.1(Colour-Transparency)	-	0	-
Clause 4.6.1.2(Colour-Tint)	-	0	-
Clause 4.6.2(Leakage Test (Closure Leakage) cls. 6.1 of IS 2798)	-	0	-
Clause 4.6.2(Leakage Test (Vibration Leakage) cls. 6.2 of IS 2798)	-	0	-
Clause 4.6.3.1(Drop Impact test)	-	0	-
Clause 4.6.3.2(Stack Load test)	-	0	-
Clause 4.6.4.1(Overall Migration Container)	-	0	-
Clause 4.6.4.1(Overall Migration Closure)	-	0	-
Clause 4.6.4.2(Specific Migration Container Barium)	-	0	-
Clause 4.6.4.2(Specific Migration Container Cobalt)	-	0	-
Clause 4.6.4.2(Specific Migration Container Copper)	-	0	-
Clause 4.6.4.2(Specific Migration Container Iron)	-	0	-
Clause 4.6.4.2(Specific Migration Container Lithium)	-	0	-
Clause 4.6.4.2(Specific Migration Container Manganese)	-	0	-
Clause 4.6.4.2(Specific Migration Container Zinc)	-	0	-
Clause 4.6.4.2(Specific Migration Container Antimony)	-	0	-
Clause 4.6.4.2(Specific Migration Container Phthalic acid, bis (2- ethylhexyl) ester (DEHP))	-	0	-
Clause 4.6.4.2(Specific Migration Closure Barium)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Cobalt)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Copper)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Iron)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Lithium)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Manganese)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Zinc)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Antimony)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Phthalic acid, bis (2- ethylhexyl) ester (DEHP))	-	0	-
Clause 4.6.4.3(Colour migration Container)	-	0	-
Clause 4.6.4.3(Colour migration Closure)	-	0	-
Clause 4.6.5(Water Potability Test (Taste))	-	0	-
Clause 4.6.5(Water Potability Test (odour))	-	0	-
Clause 5.1(Marking)	-	0	-

11 Jun, 2029

-
Included w.e.f 08.12.2025

7856

Sleen India Biz venture Private Limited, Agra

9139736

IS 15298 : part 4 (2024)

Personal Protective Equipment Part 4 Occupational Footwear (ISO 20347 : 2021, MOD) (Third Revision)

Safety Shoes-Part-4

54000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5.2(Design)	-	150	10% Discount on BIS sample.
Cl 5.2.2(" Height of upper ")	-	150	10% Discount on BIS sample.
Cl 5.2.3(Heel area)	-	150	10% Discount on BIS sample.
Cl 5.3.1.1(Construction of whole footwear)	-	200	10% Discount on BIS sample.
Cl 5.3.1.2(Upper/outsole bond strength)	-	750	10% Discount on BIS sample.
Cl 5.3.2(Leak proofness)	-	300	10% Discount on BIS sample.
Cl 5.3.3(Specific ergonomic features)	-	600	10% Discount on BIS sample.
Cl 5.3.4.2(Slip resistance on ceramic tile floor with sodium lauryl sulphate (NaLS) solution)	-	1500	10% Discount on BIS sample.
Cl 5.3.5, Table no 1 of IS 17011,(i)(Allergenic and carcinogenic disperse dyes)	-	4500	10% Discount on BIS sample.
Cl 5.3.5, Table no 1 of IS 17011 (ii)(Aromatic amines released from Azo dyes (each individual amine))	-	2200	10% Discount on BIS sample.
Cl 5.3.5, Table no 1 of IS 17011 (iii)(Aromatic amines released from Azo dyes (each individual amine))	-	2200	10% Discount on BIS sample.
Cl 5.3.5, Table no 1 of IS 17011 (iv)(Chromium (VI))	-	1200	10% Discount on BIS sample.
Cl 5.3.5, Table no 1 of IS 17011 (v)(Dimethyl fumarate (DMFU))	-	2400	10% Discount on BIS sample.
Cl 5.3.5, Table no1 of IS 17011 (vi)(Formaldehyde (free or released by partial hydrolysis))	-	1000	10% Discount on BIS sample.
Cl 5.3.5, Table no 1 of IS 17011 (vii)(Formaldehyde)	-	1000	10% Discount on BIS sample.
Cl 5.3.5, Table no 1 of IS 17011 (viii)(Organotin compounds)	-	4500	10% Discount on BIS sample.
Cl 5.3.5, Table no 1 of IS 17011 (ix)(PCP-TeCP-TriCP polychlorophenols)	-	2400	10% Discount on BIS sample.
Cl 5.3.5, Table no 1 of IS 17011 (x)(pH)	-	300	10% Discount on BIS sample.
Cl 5.3.5, Table no 1 of IS 17011 (xi)(Phthalates (each individual phthalate))	-	2800	10% Discount on BIS sample.
Cl 5.3.5, Table no 1 of IS 17011 (xii)(Nickel, on skin contact)	-	1500	10% Discount on BIS sample.
Cl 5.3.6(Seam strength)	-	750	10% Discount on BIS sample.
Cl 5.3.7(Lead Content ( National Annex A))	-	1000	10% Discount on BIS sample.
Cl 5.4.1.1(Class I footwear, determination of the area where upper requirements apply of Upper)	-	400	10% Discount on BIS sample.
Cl 5.4.1.2(Hybrid footwear, determination of the area where upper requirements apply of Upper)	-	400	10% Discount on BIS sample.
Cl 5.4.2(Thickness)	-	200	10% Discount on BIS sample.
Cl 5.4.3(Tear strength)	-	500	10% Discount on BIS sample.
Cl 5.4.4, Table 9(Tensile properties- Tensile strength)	-	500	10% Discount on BIS sample.
Cl 5.4.4, Table 9(Tensile properties- Breaking Force)	-	500	10% Discount on BIS sample.
Cl 5.4.4, Table 9(Tensile properties-Modulus at 100 % elongation)	-	500	10% Discount on BIS sample.
Cl 5.4.4, Table 9(Tensile properties- Elongation at break)	-	500	10% Discount on BIS sample.
Cl 5.4.5(Flexing resistance)	-	600	10% Discount on BIS sample.
Cl 5.4.6(Water vapour permeability and coefficient)	-	700	10% Discount on BIS sample.
Cl 5.4.7(Resistance to hydrolysis)	-	1000	10% Discount on BIS sample.
Cl 5.5.2(Lining- Tear strength)	-	450	10% Discount on BIS sample.
Cl 5.5.3(Lining- Abrasion resistance)	-	600	10% Discount on BIS sample.
Cl 5.5.4(Lining-Water vapour permeability and coefficient)	-	700	10% Discount on BIS sample.
Cl 5.6.2(Tear strength of tongue)	-	500	10% Discount on BIS sample.
Cl 5.7.1(Thickness of Insole, insock and footbed)	-	200	10% Discount on BIS sample.
Cl 5.7.2(Water permeability of insock)	-	500	10% Discount on BIS sample.
Cl 5.7.3(Water absorption and desorption of Insole, insock and footbed)	-	800	10% Discount on BIS sample.
Cl 5.7.4.1(Abrasion resistance of Insoles)	-	600	10% Discount on BIS sample.
Cl 5.7.4.2(Abrasion resistance of Insocks)	-	600	10% Discount on BIS sample.
Cl 5.8.2.1(Thickness of Outsole)	-	200	10% Discount on BIS sample.
Cl 5.8.2.2(Cleated area)	-	150	10% Discount on BIS sample.
Cl 5.8.2.3(Cleat height)	-	150	10% Discount on BIS sample.
Cl 5.8.3(Outsole- Tear strength)	-	500	10% Discount on BIS sample.
Cl 5.8.4(Outsole- Abrasion resistance)	-	700	10% Discount on BIS sample.
Cl 5.8.5(Outsole-Flexing resistance)	-	700	10% Discount on BIS sample.
Cl 5.8.6(Outsole-Resistance to hydrolysis)	-	1000	10% Discount on BIS sample.
Cl 5.8.7(Interlayer bond strength)	-	450	10% Discount on BIS sample.
Cl 6.2.1.1.2(Metallic perforation-resistant inserts (Type P))	-	500	10% Discount on BIS sample.
Cl 6.2.1.1.3(Non-metallic perforation-resistant inserts and insoles (Type PL))	-	500	10% Discount on BIS sample.
Cl 6.2.1.1.4(Non-metallic perforation-resistant inserts and insoles (Type PS))	-	500	10% Discount on BIS sample.
Cl 6.2.1.2(Construction of perforation resistant insert)	-	200	10% Discount on BIS sample.
Cl 6.2.1.3(Dimensions of perforation resistant insert)	-	200	10% Discount on BIS sample.
Cl 6.2.1.4.1(Flex resistance of perforation-resistant inserts)	-	600	10% Discount on BIS sample.
Cl 6.2.1.4.2.1(ISO 20344:2021, 5.11.2)	-	500	10% Discount on BIS sample.
Cl 6.2.1.4.2.2(ISO 20344:2021, 5.6.2.1)	-	500	10% Discount on BIS sample.
Cl 6.2.1.4.3(Stability against ageing and environmental influence of non-metallic perforationresistant inserts)	-	700	10% Discount on BIS sample.
Cl 6.2.2.1(Electrical properties of Partially conductive footwear)	-	1500	10% Discount on BIS sample.
Cl 6.2.2.2(Electrical properties of Antistatic footwear)	-	1500	10% Discount on BIS sample.
Cl 6.2.3.1(Heat insulation of outsole complex)	-	600	10% Discount on BIS sample.
Cl 6.2.3.2(Cold insulation of outsole complex)	-	600	10% Discount on BIS sample.
Cl 6.2.4(Energy absorption of seat region)	-	450	10% Discount on BIS sample.
Cl 6.2.5(Water resistance)	-	300	10% Discount on BIS sample.
Cl 6.2.6(Ankle protection)	-	450	10% Discount on BIS sample.
Cl 6.2.7.1(Cut resistance footwear- design)	-	200	10% Discount on BIS sample.
Cl 6.2.7.2(Dimensions and construction of protective area of Cut resistance footwear)	-	200	10% Discount on BIS sample.
Cl 6.2.7.3(Resistance to cutting)	-	450	10% Discount on BIS sample.
Cl 6.2.8(Scuff cap)	-	600	10% Discount on BIS sample.
Cl 6.2.9("Slip resistance on ceramic tile floor with glycerine ")	-	1500	10% Discount on BIS sample.
Cl 6.3(Upper — Water penetration and absorption)	-	300	10% Discount on BIS sample.
Cl 6.4.1(Resistance to hot contact - Outsole)	-	300	10% Discount on BIS sample.
Cl 6.4.3.1(Mechanical properties of Ladder grip)	-	500	10% Discount on BIS sample.
Cl 6.4.3.2(Design of Ladder grip)	-	200	10% Discount on BIS sample.
Cl 6.4.3.3(Cleat height in the waist area of Ladder grip)	-	200	10% Discount on BIS sample.
Cl 6.4.3.4(Heel breast of Ladder grip)	-	200	10% Discount on BIS sample.
Cl 7("Marking ")	-	200	10% Discount on BIS sample.
Cl 6.4.2(Resistance to fuel oil - Outsole)	-	300	10% Discount on BIS sample.

-
Included w.e.f 28.05.2025

7857

URS PRODUCTS AND TESTING PVT. LTD. (A29), NOIDA

8168906

IS 15885 : Part 2 : Sec 13 (2012)

Safety of lamp controlgear: Part 2 particular requirements: Sec 13 d.c. or a.c. supplied electronic controlgear for led modules

47000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking)	-	3000	-
8(Protection against accidental contact with live parts)	-	3000	-
9(Terminals)	-	4000	-
10(PROVISION FOR EARTHING)	-	5000	-
11(MOISTURE RESISTANCE)	-	4000	-
12(Electric Strength)	-	4000	-
13(Thermal endurance test for winding of ballasts)	-	3000	-
14(Fault conditions)	-	4000	-
15(Transformer heating)	-	5000	-
16(Construction)	-	4000	-
17(Creepage distance and clearances)	-	3000	-
18(Screws, current carrying parts and connections)	-	3000	-
19(Resistance to heat, fire and tracking)	-	5000	-
20(Resistance to corrosion)	-	5000	-
16(Enclosures)	-	4000	-
16(Bridging resistor in primary circuit)	-	3000	-
16(Capacitor and RC units)	-	4000	-
16(RF suppression (X-Y capacitors))	-	4000	-
16(Inductor)	-	4000	-
16(MOV/VDR)	-	4000	-
16(SMPS/Mains Transformer)	-	4000	-
16(PCB material)	-	4000	-
19(Metal base PCB for LED)	-	4000	-
19(Transparent cover)	-	5000	-
19(Bobbin)	-	4000	-
16(Insulated tape)	-	3000	-
16(Heat shrinkage sleeve)	-	4000	-
19(Terminals)	-	4000	-
16(Connector)	-	4000	-
16(Fuse)	-	4000	-
16(Internal wire)	-	4000	-
16(LED)	-	4000	-
16(Opto-coupler)	-	4000	-
16(Opto-coupler)	-	4000	-
16(EMI/EMC filter)	-	4000	-
16(Winding wire)	-	4000	-
16(Thin sheet materials)	-	4000	-
7(Marking)	-	3000	-
8("PROTECTION AGAINST ACCIDENTAL CONTACT WITH LIVE PARTS")	-	3000	-
9(TERMINALS)	-	3000	-
10(PROVISIONS FOR PROTECTIVE EARTHING)	-	4000	-
11(MOISTURE RESISTANCE AND INSULATION)	-	4000	-
12(ELECTRIC STRENGTH)	-	4000	-
14(FAULT CONDITIONS)	-	4000	-
15(TRANSFORMER HEATING)	-	4000	-
16(CONSTRUCTION)	-	4000	-
17(CREEPAGE DISTANCES AND CLEARANCES)	-	2000	-
18("SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS")	-	3000	-
19(RESISTANCE TO HEAT, FIRE AND TRACKING)	-	2000	-
20(RESISTANCE TO CORROSION)	-	3000	-
4(GENERAL REQUIREMENTS)	-	2000	-
5(GENERAL NOTES ON TESTS)	-	2000	-
6(CLASSIFICATION)	-	3000	-
7(Marking)	-	2000	-
8(Protection against accidental contact with live parts)	-	3000	-
9(Terminals)	-	3000	-
10(PROVISION FOR EARTHING)	-	5000	-
11(MOISTURE RESISTANCE)	-	6000	-
12(Electric Strength)	-	5000	-
13(Thermal endurance test for winding of ballasts)	-	5000	-
14(Fault conditions)	-	5000	-
15(Transformer heating)	-	8000	-
16(Construction)	-	2000	-
17(Creepage distance and clearances)	-	3000	-
18(Screws, current carrying parts and connections)	-	2000	-
19(Resistance to heat, fire and tracking)	-	5000	-
20(Resistance to corrosion)	-	3000	-
16(Enclosures)	-	1000	-
16(Bridging resistor in primary circuit)	-	0	-
16(Capacitor and RC units)	-	0	-
16(RF suppression (X-Y capacitors))	-	0	-
16(Inductor)	-	0	-
16(MOV/VDR)	-	0	-
16(SMPS/Mains Transformer)	-	0	-
16(PCB material)	-	0	-
19(Metal base PCB for LED)	-	0	-
19(Transparent cover)	-	0	-
19(Bobbin)	-	0	-
16(Insulated tape)	-	0	-
16(Heat shrinkage sleeve)	-	0	-
19(Terminals)	-	1000	-
16(Connector)	-	0	-
16(Fuse)	-	0	-
16(Internal wire)	-	0	-
16(LED)	-	0	-
16(Opto-coupler)	-	0	-
16(Opto-coupler)	-	0	-
16(EMI/EMC filter)	-	0	-
16(Winding wire)	-	0	-
16(Thin sheet materials)	-	0	-
7(Marking)	-	2000	-
8("PROTECTION AGAINST ACCIDENTAL CONTACT WITH LIVE PARTS")	-	3000	-
9(TERMINALS)	-	2000	-
10(PROVISIONS FOR PROTECTIVE EARTHING)	-	5000	-
11(MOISTURE RESISTANCE AND INSULATION)	-	3000	-
12(ELECTRIC STRENGTH)	-	5000	-
14(FAULT CONDITIONS)	-	5000	-
15(TRANSFORMER HEATING)	-	8000	-
16(CONSTRUCTION)	-	5000	-
17(CREEPAGE DISTANCES AND CLEARANCES)	-	3000	-
18("SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS")	-	3000	-
19(RESISTANCE TO HEAT, FIRE AND TRACKING)	-	8000	-
20(RESISTANCE TO CORROSION)	-	5000	-
4(GENERAL REQUIREMENTS)	-	1000	-
5(GENERAL NOTES ON TESTS)	-	1000	-
6(CLASSIFICATION)	-	1000	-

-
Included w.e.f 01.01.2025 Exclusion : Cl 16 (RF suppression (X-Y capacitors), MOV/VDR), (SMPS/Mains Transformer), (PCB material), (Insulated tape), (Heat shrinkage sleeve), (Connector), (Fuse), (Internal wire), (LED), (Opto-coupler), (EMI/EMC filter), (Winding wire) Cl 19 (Metal base PCB for LED), (Transparent cover), (Bobbin)

7858

HT Product Services Private Limited, Noida

8175006

IS 302 : Part 2 : Sec 21 (2024)

Household and Similar Electrical Appliancesï¿½Safety Part 2 Particular Requirements Section 21 Storage Water Heaters

rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances including direct current (DC) supplied appliances and battery-operated appliances.

24000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(General requirement)	-	0	-
5(General conditions for the tests)	-	0	-
6(Classification)	-	500	-
7(Marking and instructions)	-	500	-
8(Protection against access to live parts)	-	500	-
9(Starting of motor-operated appliances)	-	0	-
10(Power input and current)	-	1000	-
11(Heating)	-	2000	-
13(Leakage current and electric strength at operating temperature)	-	1000	-
14(Transient overvoltages)	-	0	-
15(Moisture resistance)	-	2000	-
16(Leakage current and electric strength)	-	1000	-
17(Overload protection of transformers and associated circuits)	-	0	-
18(Endurance)	-	0	-
19(Abnormal operation)	-	2000	-
20(Stability and mechanical hazards)	-	500	-
21(Mechanical strength)	-	1000	-
22(Construction)	-	1000	-
23(Internal wiring)	-	1000	-
24(Components)	-	1000	-
25(Supply connection and external flexible cords)	-	2000	-
26(Terminals for external conductors)	-	1000	-
27(Provision for earthing)	-	1000	-
28(Screws and connections)	-	1000	-
29(Clearances, creepage distances and solid insulation)	-	1000	-
30(Resistance to heat and fire)	-	2000	-
31(Resistance to rusting)	-	500	-
32(Radiation, toxicity and similar hazards)	-	0	-
A.101(Pressure test)	-	500	-
19.11.4.1(Electrostatic discharges)	-	0	-
19.11.4.2(Radiated fields)	-	0	-
19.11.4.3(Fast transient bursts)	-	0	-
19.11.4.4(Surge immunity test)	-	0	-
19.11.4.5(Immunity to conducted discharges)	-	0	-
19.11.4.6(Class 3 Voltage dips and interruptions)	-	0	-
19.11.4.7(Harmonics)	-	0	-
4(General requirement)	-	0	-
5(General conditions for the tests)	-	0	-
6(Classification)	-	0	-
7(Marking and instructions)	-	0	-
8(Protection against access to live parts)	-	0	-
9(Starting of motor-operated appliances)	-	0	-
10(Power input and current)	-	0	-
11(Heating)	-	0	-
13(Leakage current and electric strength at operating temperature)	-	0	-
14(Transient overvoltages)	-	0	-
15(Moisture resistance)	-	0	-
16(Leakage current and electric strength)	-	0	-
17(Overload protection of transformers and associated circuits)	-	0	-
18(Endurance)	-	0	-
19(Abnormal operation)	-	0	-
20(Stability and mechanical hazards)	-	0	-
21(Mechanical strength)	-	0	-
22(Construction)	-	0	-
23(Internal wiring)	-	0	-
24(Components)	-	0	-
25(Supply connection and external flexible cords)	-	0	-
26(Terminals for external conductors)	-	0	-
27(Provision for earthing)	-	0	-
28(Screws and connections)	-	0	-
29(Clearances, creepage distances and solid insulation)	-	0	-
30(Resistance to heat and fire)	-	0	-
31(Resistance to rusting)	-	0	-
32(Radiation, toxicity and similar hazards)	-	0	-
A.101(Pressure test)	-	0	-
19.11.4.1(Electrostatic discharges)	-	0	-
19.11.4.2(Radiated fields)	-	0	-
19.11.4.3(Fast transient bursts)	-	0	-
19.11.4.4(Surge immunity test)	-	0	-
19.11.4.5(Immunity to conducted discharges)	-	0	-
19.11.4.6(Class 3 Voltage dips and interruptions)	-	0	-
19.11.4.7(Harmonics)	-	0	-
12(Charging of metal-ion batteries)	-	0	-
4(General requirement)	-	0	-
5(General conditions for the tests)	-	0	-
6(Classification)	-	0	-
7(Marking and instructions)	-	0	-
8(Protection against access to live parts)	-	0	-
9(Starting of motor-operated appliances)	-	0	-
10(Power input and current)	-	0	-
11(Heating)	-	0	-
13(Leakage current and electric strength at operating temperature)	-	0	-
14(Transient overvoltages)	-	0	-
15(Moisture resistance)	-	0	-
16(Leakage current and electric strength)	-	0	-
17(Overload protection of transformers and associated circuits)	-	0	-
18(Endurance)	-	0	-
19(Abnormal operation)	-	0	-
20(Stability and mechanical hazards)	-	0	-
21(Mechanical strength)	-	0	-
22(Construction)	-	0	-
23(Internal wiring)	-	0	-
24(Components)	-	0	-
25(Supply connection and external flexible cords)	-	0	-
26(Terminals for external conductors)	-	0	-
27(Provision for earthing)	-	0	-
28(Screws and connections)	-	0	-
29(Clearances, creepage distances and solid insulation)	-	0	-
30(Resistance to heat and fire)	-	0	-
31(Resistance to rusting)	-	0	-
32(Radiation, toxicity and similar hazards)	-	0	-
A.101(Pressure test)	-	0	-
19.11.4.1(Electrostatic discharges)	-	0	-
19.11.4.2(Radiated fields)	-	0	-
19.11.4.3(Fast transient bursts)	-	0	-
19.11.4.4(Surge immunity test)	-	0	-
19.11.4.5(Immunity to conducted discharges)	-	0	-
19.11.4.6(Class 3 Voltage dips and interruptions)	-	0	-
19.11.4.7(Harmonics)	-	0	-
12(Charging of metal-ion batteries)	-	0	-

03 Dec, 2026

-
Included w.e.f 13.11.2024 Exclusion: Cl. 19.11.4.2 (Radiated fields), Cl. 19.11.4.3 (Fast transient bursts),Cl. 19.11.4.4 (Surge immunity test), Cl. 19.11.4.5 (Immunity to conducted discharges), Cl. 19.11.4.6 (Class 3 Voltage dips and interruptions), CL. 19.11.4.7 (Harmonics), 32 (Radiation, toxicity and similar hazards).

7859

ALAIPURIA TEST HOUSE PRIVATE LIMITED, GHAZIABAD

8180426

IS 2082 (2018)

Stationary storage type electric water heaters - Specification (Fifth Revision)

22000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking)	-	1250	--
7(Marking)	-	1250	--
7(Marking)	-	1250	--
7(Marking)	-	1250	--
7(Marking)	-	1250	--
7(Marking)	-	1250	--
7(Marking)	-	1250	--
7(Marking)	-	1250	--
7(Marking)	-	1250	--
7(Marking)	-	1250	--
7(Marking)	-	1250	--
7(Marking)	-	1250	--
7(Marking)	-	1250	--
7(Marking)	-	1250	--
7(Marking)	-	1250	--
7(Marking)	-	1250	--
7(Marking)	-	1250	--
7(Marking)	-	1250	--
7(Marking)	-	1250	--
7(Marking)	-	1250	--
7(Marking)	-	1250	--
7(Marking)	-	1250	--
7(Marking)	-	1250	--
7(Marking)	-	1250	--
7(Marking)	-	1250	--
7(Marking)	-	1250	--
7(Marking)	-	1250	--
7(Marking)	-	1250	--
6(Classification )	-	1250	--
6(Classification )	-	1250	--
(Cl.8 of IS 302-2-21:2011)(Protection Against Access to Live Parts)	-	500	--
(Cl.10 of IS 302-2-21: 2011)(Power Input & Current)	-	1000	--
(Cl.11 of 302-2-21:2011)(Heating)	-	1000	--
(Cl.11 of 302-2-21:2011)(Heating)	-	1000	--
(Cl.11 of 302-2-21:2011)(Heating)	-	1000	--
(Cl.13 of IS 302-2-21:2011)(Leakage Current )	-	500	--
(Cl.13 of IS 302-2-21:2011)(Electrical Strength at Operating Temperature)	-	500	--
(Cl.15 of IS 302-2-21-2011)(Moisture Resistance)	-	1000	--
(Cl.15 of IS 302-2-21-2011)(Moisture Resistance)	-	1000	--
(Cl.15 of IS 302-2-21-2011)(Moisture Resistance)	-	1000	--
(Cl.17 of IS 302-2-21:2011)(Overload protection of transformers & associated circuits)	-	2000	--
(Cl.19 of IS 302-2-21:2011)(Abnormal Operation)	-	1000	--
(Cl.19 of IS 302-2-21:2011)(Abnormal Operation)	-	1000	--
(Cl.19 of IS 302-2-21:2011)(Abnormal Operation)	-	1000	--
(Cl.19 of IS 302-2-21:2011)(Abnormal Operation)	-	1000	--
(Cl.20 of IS 302-2-21:2011)(Stability & Mechanical Hazards)	-	500	--
(Cl.21ofIS302-2-21:2011)(Mechanical strength)	-	750	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	1500	--
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	500	--
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	500	--
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	500	--
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	500	--
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	500	--
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	500	--
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	500	--
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	500	--
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	500	--
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	500	--
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	500	--
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	500	--
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	500	--
(Cl.24ofIS302-221:2011)(Component)	-	750	--
(Cl.24ofIS302-221:2011)(Component)	-	750	--
(Cl.24ofIS302-221:2011)(Component)	-	750	--
(Cl.24ofIS302-221:2011)(Component)	-	750	--
(Cl.24ofIS302-221:2011)(Component)	-	750	--
(Cl.24ofIS302-221:2011)(Component)	-	750	--
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	750	--
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	750	--
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	750	--
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	750	--
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	750	--
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	750	--
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	750	--
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	750	--
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	750	--
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	750	--
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	750	--
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	750	--
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	750	--
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	750	--
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	750	--
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	750	--
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	750	--
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	750	--
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	750	--
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	750	--
(Cl.26 of IS 302-2-21: 2011)(Terminals for External Conductors)	-	750	--
(Cl.26 of IS 302-2-21: 2011)(Terminals for External Conductors)	-	750	--
(Cl.26 of IS 302-2-21: 2011)(Terminals for External Conductors)	-	750	--
(Cl.26 of IS 302-2-21: 2011)(Terminals for External Conductors)	-	750	--
(Cl.26 of IS 302-2-21: 2011)(Terminals for External Conductors)	-	750	--
(Cl.26 of IS 302-2-21: 2011)(Terminals for External Conductors)	-	750	--
(Cl.26 of IS 302-2-21: 2011)(Terminals for External Conductors)	-	750	--
(Cl.26 of IS 302-2-21: 2011)(Terminals for External Conductors)	-	750	--
(Cl.26 of IS 302-2-21: 2011)(Terminals for External Conductors)	-	750	--
(Cl.26 of IS 302-2-21: 2011)(Terminals for External Conductors)	-	750	--
(Cl.26 of IS 302-2-21: 2011)(Terminals for External Conductors)	-	750	--
(Cl.27 of IS 302-2-21:2011)(Provision for Earthing)	-	500	--
(Cl.27 of IS 302-2-21:2011)(Provision for Earthing)	-	500	--
(Cl.27 of IS 302-2-21:2011)(Provision for Earthing)	-	500	--
(Cl.27 of IS 302-2-21:2011)(Provision for Earthing)	-	500	--
(Cl.27 of IS 302-2-21:2011)(Provision for Earthing)	-	500	--
(Cl.27 of IS 302-2-21:2011)(Provision for Earthing)	-	500	--
(Cl.28 of IS 302-2-21:2011)(Screws & Connections)	-	500	--
(Cl.29ofIS302-2-21:2011)(Clearances, Creepage Distances and Solid Insulation)	-	500	--
(Cl.30 of IS 302-2-21:2011)(Resistance to Heat & Fire)	-	1500	--
(Cl.30 of IS 302-2-21:2011)(Resistance to Heat & Fire)	-	1500	--
(Cl.31 of IS 302-2-21:2011)(Resistance to Rusting)	-	750	--
(Cl.15 of IS 2082:2018)(Verification of the Rated Capacity)	-	2250	--
(Cl.16 of IS 2082:2018)(Standing Loss per 24 Hours)	-	6000	--
(Cl.17 of IS 2082:2018)(Hot Water Output)	-	3000	--
(Cl.18 of IS 2082:2018)( Reheating Time)	-	2500	--
(Cl.19 of IS 2082:2018)(Mixing Factor)	-	1250	--
(Cl.20 of IS 2082:2018)(Deviation of Dial Calibration)	-	1500	--
(Cl.21 of IS 2082:2018)(Cyclic Temperature Variation)	-	1000	--
(Cl.22 of IS 2082:2018)(Finish)	-	1000	--
Cl.22 of IS 2082:2018(Finish)	-	1000	--
Cl.21 of IS 2082:2018(Cyclic Temperature Variation)	-	1000	--
Cl.20 of IS 2082:2018(Deviation of Dial Calibration)	-	1500	--
Cl.19 of IS 2082:2018(Mixing Factor)	-	1250	--
Cl.18 of IS 2082:2018( Reheating Time)	-	2500	--
Cl.17 of IS 2082:2018(Hot Water Output)	-	3000	--
Cl.16 of IS 2082:2018(Standing Loss per 24 Hours)	-	6000	--
Cl.15 of IS 2082:2018(Verification of the Rated Capacity)	-	2250	--
Cl.31 of IS 302-2-21:2018(Resistance to Rusting)	-	375	--
Cl.30.2 of IS 302-1:2008(Resistance to Heat & Fire : Glow wire test )	-	750	--
Cl.30.1 of IS 302-1:2008(Resistance to Heat & Fire : Ball pressure test )	-	750	--
Cl.29.2 of IS 302-1:2008(Clearances, Creepage Distances and Solid Insulation : Creepage distance )	-	250	--
Cl.29.1 of IS 302-1:2008(Clearances, Creepage Distances and Solid Insulation : Clearance distance )	-	250	--
Cl.28 of IS 302-2-21:2018(Screws & Connections)	-	500	--
Cl.27.5 of IS 302-1:2008(Provision for Earthing : ECR )	-	250	--
Cl.27 of IS 302-2-21:2018(Provision for Earthing)	-	250	--
Cl.26 of IS 302-2-21: 2018(Terminals for External Conductors)	-	750	--
Cl.25.18 of IS 302-1:2008(Supply Connection & External Flexible Cords)	-	90	--
Cl.25.15 of IS 302-1:2008(Supply Connection & External Flexible Cords : Cord grip test - displacement )	-	90	--
Cl.25.15 of IS 302-1:2008(Supply Connection & External Flexible Cords : Cord grip test )	-	90	--
Cl.25.12 of IS 302-1:2008(Supply Connection & External Flexible Cords : Moulding of supply cord )	-	90	--
Cl.25.10 of IS 302-1:2008(Supply Connection & External Flexible Cords : Colour of Earthing conductor )	-	90	--
Cl.25.8 of IS 302-2-21:2018(Supply Connection & External Flexible Cords : Resistance of supply cord )	-	90	--
Cl.25.5 of IS 302-1:2008(Supply Connection & External Flexible Cords : Type of attachment )	-	90	--
Cl.25 of IS 302-2-21:2018(Supply Connection & External Flexible Cords : connection to the supply mains)	-	90	--
Cl.24.102 of IS 302-221:2018(Component : Operation of thermal cut-out )	-	250	--
Cl.24.101 of IS302-221:2018(Component : Location of non self reseting thermal cut out )	-	250	--
Cl.24of IS 302-221:2018(Component : Relevent Indian standards )	-	250	--
Cl. 23 of IS 302-1:2008(Internal Wiring : color identification for earthing conductor )	-	250	--
Cl. 23 of IS 302-1:2008(Internal Wiring )	-	250	--
Cl.22.111 of IS 302-2-21:2018(Construction : Resistance to vacuum )	-	55	--
Cl.22.110 of IS 302-2-21:2018(Construction : meterial of connections )	-	55	--
Cl.22.110 of IS 302-2-21:2018(Construction : Material of Inner conatiner )	-	55	--
Cl.22.109 of IS 302-2-21:2018(Construction : Drain for appliance having a capacity of more than 15 liter)	-	55	--
Cl.22.108 of IS 302-2-21:2018(Construction : fixing to wall )	-	55	--
Cl.22.107 of IS 302-2-21:2018(Construction : Position of Heating elements and thermal control sensor)	-	55	--
Cl.22.106 of IS 302-2-21:2018(Construction : Operation of thermal cut- out )	-	55	--
Cl.22.104 of IS 302-2-21:2018(Construction : Outlet of open outlet heater )	-	55	--
Cl.22.103 of IS 302-2-21:2018(Construction : Operation of Pressure relieve devices )	-	55	--
Cl.22.102 of IS 302-2-21:2018(Construction : repeated drawing of water temp )	-	55	--
Cl.22.101 of IS 302-2-21:2018(Construction : rated pressure of closed water heater )	-	55	--
Cl.22.47 of IS 302-2-21:2018 (Construction : Water pressure test )	-	55	--
Cl.22.44 of IS 302-1:2008(Construction : Shape and decoration of enclosure)	-	55	--
Cl.22.34, Cl 22.35 of IS 302-1:2008(Construction : Shaft of operating Knobs )	-	55	--
Cl.22.33 of IS 302-1:2008(Construction : Direct contact of liquids )	-	55	--
Cl 22.26 ,Cl.22.28, Cl 22.29, Cl 22.30 , Cl 22.31, Cl 22.32 of IS 302-1:2008(Construction : Supplymentry/ double / reinforced insulation for Class II/ Class III appliance )	-	55	--
Cl.22.18 Of IS 302-1:2008(Construction : Resistance to corrosion )	-	55	--
Cl.22.17 of IS 302-1:2008(Construction : Spacers )	-	55	--
Cl.22.14 of IS 302-1:2008(Construction : ragged or sharp edges)	-	55	--
Cl.22.12 of IS 302-1:2008(Construction : Fixing of Handle, knob, grips, levers and similar parts)	-	55	--
Cl.22.11 of IS 302-1:2008(Construction : Fixing of non detachable part )	-	55	--
Cl.22.7 of IS 302-1:2008(Construction: adequate safeguards against the risk of excessive pressure)	-	55	--
Cl.22.6 of IS 302-2-21:2018(Construction : Size of drain hole )	-	55	--
Cl.22.2 of IS 302-1:2008(Construction : Provision to ensure all pole disconnection )	-	55	--
Cl.22.1 of IS 302-1:2008(Construction : IP test )	-	55	--
Cl.21.2 of IS 302-1:2008(Mechanical strength : prevent penetration by sharp implements. )	-	375	--
Cl.21.1 of IS 302-1:2008(Mechanical strength : Rough handling in normal use)	-	375	--
Cl.20 of IS 302-1:2008(Stability & Mechanical Hazards)	-	500	--
Cl.19 of IS 302-2-21:2018(Abnormal Operation : leakage from container during test)	-	200	--
Cl.19 of IS 302-2-21:2018(Abnormal Operation : High Voltage )	-	200	--
Cl.19 of IS 302-2-21:2018(Abnormal Operation : Insulation of the supply cable or cord)	-	200	--
Cl.19 of IS 302-2-21:2018(Abnormal Operation : emission of flame or molten metal or poisonous or ignitable gas )	-	200	--
Cl.16 of IS 302-2-21-2018(Leakage current and Electric strength (After humidity): Electric Strentgh )	-	1500	--
Cl.16 of IS 302-2-21-2018(Leakage current and Electric strength (After humidity): Leakage current )	-	1500	--
Cl.15 of IS 302-2-21-2018(Moisture Resistance)	-	1000	--
Cl.13 of IS 302-2-21:2018(3 Strength at Operating Temperature)	-	500	--
Cl.13 of IS 302-2-21:2018(Leakage Current )	-	500	--
Cl.11 of 302-2-21:2018(Heating : Room Temp.)	-	300	--
Cl.11 of 302-2-21:2018(Heating : Temp of Rubber or PVC insulation of internal and external wiring)	-	300	--
Cl.11 of 302-2-21:2018(Heating : Temp of Walls, ceilings and floor of the test corner )	-	300	--
Cl.10 of IS 302-2-21: 2018(Power Input & Current)	-	1000	--
Cl.8 of IS 302-2-21:2018(Protection Against Access to Live Parts)	-	500	--
7.101(Marking : Indifiction of water inlet and water outlet )	-	50	--
7.14(Marking : Legibility and durability)	-	500	--
7.13(Marking : Official language of Instruction )	-	50	--
7.11(Marking : Indication of controls )	-	50	--
7.8(Marking : Terminals )	-	50	--
7.6(Marking : Symbol used )	-	50	--
7.1(Marking : Warning for Open- outlet )	-	50	--
7.1(Marking : Statement for pressure reducing valve ( For rated pressure less than 0.6 MPa))	-	50	--
7.1(Marking : Rated capacity)	-	50	--
7.1(Marking : Country of manufacture)	-	50	--
7.1(Marking: IP Number)	-	50	--
7.1(Marking: Symbol for Class II)	-	50	--
7.1(Marking: Model or type reference)	-	50	--
7.1(Marking : Rated power input)	-	50	--
7.1(Marking : Symbol for nature of supply )	-	50	--
4(GENERAL REQUIREMENT)	-	1250	--
5(GENERAL CONDITIONS FOR THE TESTS)	-	50	--
12(THERMOSTAT SETTING)	-	1250	--
Cl-10(Mounting of the water heater)	-	1250	--
Cl-12(Thermostat setting)	-	1250	--
Cl-13(Measurement of energy consumption)	-	2250	--
Cl-14(Verification of the rated capacity)	-	2250	--
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	750	--
Cl.19 of IS 302-2-21:2018(Abnormal Operation : Wall ceiling temp. of test corner )	-	200	--
7.1(Marking : Statement for a pressure-relief device)	-	50	--
7.1(Marking : Rated pressure)	-	50	--
7.1(Marking: Name, trademark or identification mark of manufacturer )	-	50	--
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	750	--
Cl.22.6 of IS 302-1:2008(Construction : Effect of water on 3 insulation )	-	750	--
7.1(Marking : Rated Voltage )	-	50	--
Cl-11(Measurements of stored water temperature)	-	750	--
(Cl.14ofIS302-2-21:2011)(Transient Over Voltages)	-	500	-
Cl.14 of IS 302-2-21:2018(Transient Over Voltages)	-	500	-

03 Oct, 2027

-
-

7860

Atmy Analytical Labs Pvt. Ltd., Faridabad

8167506

IS 2494 : Part 1 (1994)

V - Belts - Endless V - Belts for industrial purposes: Part 1 general purpose - Specification (Second Revision)

16500 View breakup
-

Clause No.	Exclusion	Remark
11.0(Marking)	-	-
10.1(Elongation)	-	-
10.1(Tensile Strength)	-	-
8.0(Transmitting Capacities)	-	-
7.2.2(Matched Belts - Code)	-	-
7.2.1(Matched Belts - Difference)	-	-
7.1(Belt Pitch Length)	-	-
6.0(Designation)	-	-
5 Table 2B(Cross sectional dimension)	-	-
5 Table 2B(Cross sectional dimension)	-	-
5 Table 2A(Cross sectional dimension)	-	-
5 Table 2A(Cross sectional dimension)	-	-
5 Table 2A(Cross sectional dimension)	-	-
5 Table 2A(Cross sectional dimension)	-	-
5 Table 2A(Cross sectional dimension)	-	-
5 Table 2A(Cross sectional dimension)	-	-
5 Table 2A(Cross sectional dimension)	-	-
5 Table 2A(Cross sectional dimension)	-	-
5 Table 2A(Cross sectional dimension)	-	-
5 Table 1(Cross sectional dimension)	-	-
5 Table 1(Cross sectional dimension)	-	-
5 Table 1(Cross sectional dimension)	-	-
5 Table 1(Cross sectional dimension)	-	-
4.1(Material and Workmanship)	-	-
4.1(Material -Reinforcing polyester cord/fabric of the V-belts)	-	-
4.1(Material and Workmanship)	-	-
7.2(Test Matched Belts)	-	-
5 & 11(Test Belt ride position of top surface of belt with respect to top of pully groove.)	-	-
Clause 5 Table 1(Nominal Pitch Width (Wp))	-	-
Clause 5 Table 1(Nominal Height (T))	-	-
Clause 5 Table 1(Nominal Included Angle (A))	-	-
Clause 5 Table 1(Nominal Pitch Width (W))	-	-
Cl-4.3(Presence of polychloroprene rubber on outside jacket of V-belt)	-	-
7.2(Test Matched Belts)	-	-
5 & 11(Test Belt ride position of top surface of belt with respect to top of pully groove.)	-	-
Clause 5 Table 1(Nominal Pitch Width (Wp))	-	-
Clause 5 Table 1(Nominal Height (T))	-	-
Clause 5 Table 1(Nominal Included Angle (A))	-	-
Clause 5 Table 1(Nominal Pitch Width (W))	-	-
Cl-4.3(Presence of polychloroprene rubber on outside jacket of V-belt)	-	-

25 Feb, 2027

-
-

Bureau of Indian Standards

The National Standards Body of India

Search by IS Number