BIS - LIMS (Laboratory Information Management System)

Search by IS Number

Reset

14027 Results

S.No.

Lab Name

Osl Code

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

9751

The Synthetic and Art Silk Mills' Research Association (SASMIRA), MUMBAI

7175004

IS 12171 (2019)

Cotton bales – Specification (third revision)

2900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.3(Moisture Content)	-	500	-
5.2.1(Dimensions)	-	200	-
5.2.2(Mass (Weight))	-	200	-
5.2.3.1(a) Cotton fabric)	-	200	-
5.2.3.1(b) Baling hoops)	-	400	-
5.2.3.1(c) Cotton twine)	-	1400	-
5.1.4(Strength of Fibre)	-	0	-

14 Dec, 2026

-
-

9752

The Synthetic and Art Silk Mills' Research Association (SASMIRA), MUMBAI

7175004

IS 16089 (2013)

Jute agro-textile – Sapling bags for growth of seedling/ sapling – Specification

2200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4, Table 1, (i)(Mass, g/m², Min)	-	200	-
Clause 4, Table 1, (ii)(Thickness, mm)	-	200	-
Clause 4, Table 1, (iii)(Open area, percent)	-	0	-
Clause 4, Table 1, (iv) a(Threads/dm, Warp)	-	200	-
Clause 4, Table 1, (iv) b(Threads/dm, Weft)	-	0	-
Clause 4, Table 1, (v)(Width of Hessian fabric, cm)	-	200	-
Clause 4, Table 1, (vi)(Length and width of sapling bags, cm, Min)	-	400	-
Clause 4, Table 1, (vii)(Water holding capacity, percent)	-	500	-
Clause 4, Table 1, (viii) a(Tensile strength, kN/m, Warp)	-	500	-
Clause 4, Table 1, (viii) b(Tensile strength, kN/m, Weft)	-	0	-

14 Dec, 2026

-
-

9753

BIS, Central Laboratory (CL)

None

IS 3521 : Part 2 (2021)

Personal Fall Arrest Systems Specification Part 2 Lanyards and Energy Absorbers

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2.6 (Static strength)	-
4.3.5 (Dynamic performance)	-
5.2.4 (Corrosion resistance)	-
6.2 (Marking)	-
4.2.4 (Fittings)	-

-
Excluding Test Facility only for clauses 4.1, 4.2, 4.3

9754

Central Institute of Petrochemicals Engineering & Technology (CIPET), CSTS - Dehradun

9178004

IS 16098 Part 2 (2013)

Structured-Wall Plastics Piping Systems for Non-Pressure Drainage and Sewerage Part 2 Pipes and Fittings with Non-Smooth External Surface, Type B

57450.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Table -1 Cl. No. 5.1, i)(Base Density)	-	500.00	-
Table -1 Cl. No. 5.1, ii)(Melt Flow Rate (MFR) at (190ºC, 5kg load))	-	1100.00	-
Table -1 Cl. No. 5.1, iii)(Thermal Stability (Oxidation Induction Test, OIT) at 200ºC)	-	2200.00	-
" 5.1 Table-2 ", i)(Resistance to Internal Pressure 165hrs)	-	4800.00	-
" 5.1 Table-2 ", ii)(Resistance to Internal Pressure 1000hrs)	-	11000.00	-
6.3.3(Out Side Diameter)	-	1000.00	-
7.1(Appearance)	-	1000.00	-
7.2 Table-6 (i)(Resistance to Heating oven test at (110±2ºC for 30 minute))	-	1100.00	-
9 Table-12 (i)(Tightness of elastomeric ring seal Joint)	-	1000.00	-
8.1.1 Table-10 (i)(Ring Stiffness)	-	0.00	Test Charge for this parameter taken above.
8.1.1 Table-10 (ii)(Impact Strength at (0±1 ºC))	-	0.00	Test Charge for this parameter taken above.
8.1.1, 8.1.2 Table-10 (iii)(Ring flexibility 30% of dem)	-	0.00	Test Charge for this parameter taken above.
6.3.1 & Table-5(Dim (min.) E4 (min) E5 (min.) Socket Length)	-	0.00	Test Charge for this parameter taken above.
6.3.2(Length of Pipe)	-	0.0	Test Charge for this parameter taken above.
6.3.5.1.1(Ring Stiffness of Spigot + socket)	-	0.00	Test Charge for this parameter taken above.
"6.3.5.1.5 Table-5 "(Socket thickness Avg. (min.) Avg.)	-	0.00	Test Charge for this parameter taken above.
6.3.5.2(Wall Thickness(e4 min))	-	0.00	Test Charge for this parameter taken above.
9 Table 12 (ii)(Water tightness)	-	0.00	Test Charge for this parameter taken above.
7.1.1(Color of Finished Pipes)	-	0.00	Test Charge for this parameter taken above.
6.3.5.2("Construction Height of body wall(ec) Wall Thickness (emin) ")	-	0.00	Test Charge for this parameter taken above.

24 Apr, 2027

-
Exclusion: Cl 8.1.1 Table-10 (iv) (Creep ratio) Cl 9 Table- 12 (iii) (Resistance to combined temperature cycling and external loading)

9755

Central Institute of Petrochemicals Engineering & Technology (CIPET), CSTS - Dehradun

9178004

IS 16098 Part 1 (2013)

Structured-Wall Plastics Piping Systems for Non-Pressure Drainage and Sewerage Part 1 Pipes and Fittings With Smooth External Surface, Type A

60950.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2 Table 1(Composition of the material- Resistance to internal hydrostatic Pipe material (1) 1 000 IS 12235 No seepage, cracking, pressure at 60ºC)	-	11500.00	Resistance to Internal Hydrostatic Pressure at 60 °C/1000h. (pipes & Fittings) = 11000 Specimen/Conditioning Charge= 500
6.1(Wall Construction Designated as Type A)	-	500.00	-
6.3.1(Dimension of Pipes and Fittings Diameter of pipe)	-	500.00	-
7.1(Appearance)	-	500.00	-
7.2(Colour )	-	0.00	Appearance and color have single charge.
7.3(Vicat softening temperature of pipes)	-	1100.00	-
7.4(Resistance to Dichloromethane)	-	1000.00	-
7.5(longitudinal reversion)	-	1200.00	Test Charge= 700.00 Specimen/Conditioning Charge- 500.00
8.1(Appearance and colour)	-	500.00	-
8.2(Vicat softening temperature of fittings)	-	1100.00	-
8.3(Effect of Heating (Stress Relief Test))	-	1200.00	Test Charge= 700.00 Specimen Charge= 500.00
9.1(Ring stiffness)	-	1600.00	Test Charge= 1100.00 Specimen Charge= 500.00
9.2(Resistance to external blows at o C)	-	1600.00	Test Charge= 1100.00 Specimen Charge= 500.00
9.3(Ring flexibility)	-	1100.00	-
10.1(Impact Strength of Injection Moulded and Fabricated Fittings)	-	1100.00	-
12.1(Elastomeric Sealing Ring Joints)	-	1350.00	test Charge= 850.00 specimen Charge = 500.00
12.1.2(Tightness of Elastomeric Sealing Ring Joints (Internal Vaccum ))	-	2500.00	Internal Negative Hydrostatic Pressure test (internal Vacuum) for Elastomeric Sealing ring joint = 2000.00 Specimen Charge= 500.00
6.3.2(Dimension of Pipes and Fittings Lengths of Pipe)	-	0.00	ALREADY TEST CHARGE TAKEN FOR ABOVE PARAMETER.
6.3.3(Dimension of Pipes and Fittings Diameters of Pipes and Spigots of Pipes orFittings)	-	0.00	ALREADY TEST CHARGE TAKEN FOR ABOVE PARAMETER.
7.0(Physical characteristics for pipes and fittings Appearance)	-	0.00	ALREADY TEST CHARGE TAKEN FOR ABOVE PARAMETER.
7.1.1(Physical characteristics for pipes and fittings Colour of Finished Pipes)	-	0.00	ALREADY TEST CHARGE TAKEN FOR ABOVE PARAMETER.
7.2(Physical characteristics for pipes and fittings )	-	0.00	ALREADY TEST CHARGE TAKEN FOR ABOVE PARAMETER.
7.3(Physical characteristics for pipes and fittings )	-	0.00	ALREADY TEST CHARGE TAKEN FOR ABOVE PARAMETER.
8.1.1(Mechanical Characteristics of Pipes General)	-	0.00	-
8.1.1(Mechanical Characteristics of Pipes General)	-	0.00	-
8.1.2 (a)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0.00	ALREADY TEST CHARGE TAKEN FOR ABOVE PARAMETER.
8.1.2 (b)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0.00	ALREADY TEST CHARGE TAKEN FOR ABOVE PARAMETER.
8.1.2 (c)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0.00	ALREADY TEST CHARGE TAKEN FOR ABOVE PARAMETER.
8.1.2 (d)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0.00	ALREADY TEST CHARGE TAKEN FOR ABOVE PARAMETER.
8.1.2 (e)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0.00	ALREADY TEST CHARGE TAKEN FOR ABOVE PARAMETER.
8.2.1(Mechanical Characteristics of Fittings General)	-	0.00	-
8.2.1(Mechanical Characteristics of Fittings General)	-	0.00	-
8.2.2(Mechanical Characteristics of Fittings)	-	0.00	-
8.3(Joints)	-	0.00	-
9 (Table 12)(Performance Requirements)	-	0.00	-
9 (Table 12)(Performance Requirements)	-	0.00	-
9 (Table 12)(Performance Requirements)	-	0.00	-
11.1(Marking General)	-	0.00	-
11.2.1(Minimum Required Marking Pipes)	-	0.00	-
11.2.1(Minimum Required Marking Pipes)	-	0.00	-
11.2.1(Minimum Required Marking Pipes)	-	0.00	-
11.2.1(Minimum Required Marking Pipes)	-	0.00	-
11.2.1(Minimum Required Marking Pipes)	-	0.00	-
11.2.2(Minimum Required Marking Fittings)	-	0.00	-
11.2.2(Minimum Required Marking Fittings)	-	0.00	-
11.2.2(Minimum Required Marking Fittings)	-	0.00	-
11.2.2(Minimum Required Marking Fittings)	-	0.00	-
11.2.2(Minimum Required Marking Fittings)	-	0.00	-
11.2.2(Minimum Required Marking Fittings)	-	0.00	-
5.0(Composition of the material)	-	0.00	-
5.1(Composition of the material)	-	0.00	-
5.3(Composition of the material)	-	0.00	-
5.4(Composition of the material)	-	0.00	-
6.0(DESIGNATION OF WALL CONSTRUCTIONS AND EXAMPLES OF TYPICAL JOINTING METHODS )	-	0.00	-
6.2(Deswignation)	-	0.00	-
6.3(Dimensions of pipes and fittings)	-	0.00	ALREADY TEST CHARGE TAKEN FOR ABOVE PARAMETER.
6.3.1 Table 2(Mean outside diameter)	-	0.00	ALREADY TEST CHARGE TAKEN FOR ABOVE PARAMETER.
6.3.2 Table 3(Wall thickness)	-	0.00	ALREADY TEST CHARGE TAKEN FOR ABOVE PARAMETER.
6.3.3 Fig 2(Length of pipe)	-	0.00	ALREADY TEST CHARGE TAKEN FOR ABOVE PARAMETER.
6.3.4,Table 4,5(Dimensions of Integral sckets and spigot ends)	-	0.00	ALREADY TEST CHARGE TAKEN FOR ABOVE PARAMETER.
6.3.4.1(Wall thickness of sockets)	-	0.00	ALREADY TEST CHARGE TAKEN FOR ABOVE PARAMETER.
6.3.4.2(Fabricated fittings)	-	0.00	-
6.3.4.3(Rotational moulded fittings)	-	0.00	-
6.3.4.4(Type of fittings)	-	0.00	-
7.0(Physical characteristics of pipes)	-	0.00	-
8.0(Physical characteristics of fittings)	-	0.00	-
9.0(Mechanical characteristics ofpipes)	-	0.00	-
10.0(Mechanical Characteristics of fittings)	-	0.00	-
11.0(Joints)	-	0.00	-
11.1(Elastomeric Sealing Rings)	-	0.00	-
11.2(Solvent cement)	-	0.00	-
12.0(PERFORMANCE REQUIREMENTS)	-	0.00	-
12.1.1(Tightness of Elastomeric Sealing Ring Joints (Water pressure))	-	0.00	ALREADY TEST CHARGE TAKEN FOR ABOVE PARAMETER.
12.2(Solvent cement joints)	-	0.00	-
12.2.1(Tightness of Solvent cemented Ring Joints )	-	0.00	ALREADY TEST CHARGE TAKEN FOR ABOVE PARAMETER.
12.2.2(Tightness of Solvent cemented Ring Joints (Vaccum pressure))	-	0.00	ALREADY TEST CHARGE TAKEN FOR ABOVE PARAMETER.
6.3.1(Dimension of Pipes and Fittings Diameter of pipe)	-	0.00	ALREADY TEST CHARGE TAKEN FOR ABOVE PARAMETER.
6.3.2(Dimension of Pipes and Fittings Lengths of Pipe)	-	0.00	ALREADY TEST CHARGE TAKEN FOR ABOVE PARAMETER.
6.3.3(Dimension of Pipes and Fittings Diameters of Pipes and Spigots of Pipes orFittings)	-	0.00	ALREADY TEST CHARGE TAKEN FOR ABOVE PARAMETER.
7.0(Physical characteristics for pipes and fittings Appearance)	-	0.00	-
7.1.1(Physical characteristics for pipes and fittings Colour of Finished Pipes)	-	0.00	-
7.2(Physical characteristics for pipes and fittings )	-	0.00	-
7.3(Physical characteristics for pipes and fittings )	-	0.00	-
8.1.1(Mechanical Characteristics of Pipes General)	-	0.00	-
8.1.1(Mechanical Characteristics of Pipes General)	-	0.00	-
8.1.2 (a)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0.00	ALREADY TEST CHARGE TAKEN FOR ABOVE PARAMETER.
8.1.2 (b)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0.00	ALREADY TEST CHARGE TAKEN FOR ABOVE PARAMETER.
8.1.2 (c)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0.00	ALREADY TEST CHARGE TAKEN FOR ABOVE PARAMETER.
8.1.2 (d)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0.00	ALREADY TEST CHARGE TAKEN FOR ABOVE PARAMETER.
8.1.2 (e)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0.00	ALREADY TEST CHARGE TAKEN FOR ABOVE PARAMETER.
8.2.1(Mechanical Characteristics of Fittings General)	-	0.00	-
8.2.1(Mechanical Characteristics of Fittings General)	-	0.00	-
8.3(Joints)	-	0.00	-
9 (Table 12)(Performance Requirements)	-	0.00	-
9 (Table 12)(Performance Requirements)	-	0.00	-
9 (Table 12)(Performance Requirements)	-	0.00	-
11.1(Marking General)	-	0.00	-
11.2.1(Minimum Required Marking Pipes)	-	0.00	-
11.2.1(Minimum Required Marking Pipes)	-	0.00	-
11.2.1(Minimum Required Marking Pipes)	-	0.00	-
11.2.1(Minimum Required Marking Pipes)	-	0.00	-
11.2.1(Minimum Required Marking Pipes)	-	0.00	-
11.2.2(Minimum Required Marking Fittings)	-	0.00	-
11.2.2(Minimum Required Marking Fittings)	-	0.00	-
11.2.2(Minimum Required Marking Fittings)	-	0.00	-
11.2.2(Minimum Required Marking Fittings)	-	0.00	-
11.2.2(Minimum Required Marking Fittings)	-	0.00	-
11.2.2(Minimum Required Marking Fittings)	-	0.00	-
6.3.4 Table 4 & 5(Dimensions of Integral Socket and spigot ends)	-	0.00	ALREADY TEST CHARGE TAKEN FOR ABOVE PARAMETER.
6.3.4 Table 4 & 5(Outside diameter (dsm) min)	-	0.00	ALREADY TEST CHARGE TAKEN FOR ABOVE PARAMETER.
6.3.4 Table 4 & 5(C max)	-	0.00	ALREADY TEST CHARGE TAKEN FOR ABOVE PARAMETER.
7.1.1(Colour of finished pipes)	-	0.00	ALREADY TEST CHARGE TAKEN FOR ABOVE PARAMETER.
12.1.1(Tightness of Elastomeric Sealing Ring Joints (Water Pressure))	-	0.00	ALREADY TEST CHARGE TAKEN FOR ABOVE PARAMETER.
12.1.2(Tightness of Elastomeric Sealing Ring Joints (Internal Vacuum))	-	0.00	ALREADY TEST CHARGE TAKEN FOR ABOVE PARAMETER.
8.2.2(Mechanical Characteristics of Fittings)	-	0.00	-

24 Apr, 2027

-
Exclusion: Cl 9.4 (Creep ratio) Cl 12.1.3 (Resistance to Combined Temperature Cycling and External Loading)

9756

BIS, Eastern Regional Laboratory (ERL)

None

IS 12254 (2021)

POLYVINYLCHLORIDE PVC INDUSTRIAL BOOTS - SPECIFICATION Second Revision

For all type and variety

20400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.4.8.1 (Conductive Footwear)	-
Cl.6.1 (Volatility- IS 12240 (Part 4))	-
Cl.6.2 (Lead Content-IS 12240 (Part 5),)	-
Table 1 as per IS 17011 2018 (pH)	-
Table 1 as per IS 17011 2018 (Phthalates (each individual phthalate))	-
Table 1 as per IS 17011 2018 (Nickel, on skin contact)	-
Table 1 as per IS 17011 2018 (Allergenic and carcinogenic disperse dyes)	-
Table 1 as per IS 17011 2018 (Aromatic amines released from Azo dyes (each individual amine))	-
Table 1 as per IS 17011 2018 (Chromium (VI))	-
5.2 (Size)	-
5.3 (Height)	-
5.4.2 (Ergonomic feature)	-
5.4.3 (Sole bond)	-
5.4.5 (Leak proofness)	-
5.4.6.2 (Internal length of toecaps)	-
5.4.6.4 (Impact resistance)	-
5.4.6.5 (Compression resistance)	-
5.4.7 (Colour)	-
5.4.8.3.2 (Penetration resistance)	-
5.4.8.4 (Cut resistance)	-
5.4.8.6 (Outsole resistance to fuel oil)	-
5.5.1 (Upper material)	-
5.5.2 (Upper tensile strength)	-
5.5.3 (Upper flexing)	-
5.5.4 (Upper Hardness)	-
5.6.1 (Lining material)	-
5.6.2 (Lining Tear strength)	-
5.6.3 (Lining abrasion)	-
5.6.4 (Lining adhesion with upper)	-
5.7.1 (Insole material)	-
5.7.2 (Insole abrasion)	-
5.7.3 (Water absorption and desorption)	-
5.9.1 (Insock material)	-
5.9.2 (Inscok abrasion resistance)	-
5.9.3 (Insock water absorption and desorption)	-
5.11.1 (Outsole material)	-
5.11.2 (Outsole density)	-
5.11.3 (Outsole Interlayer bond)	-
5.11.4 (Outsole tear)	-
5.11.5 (Outsole Abrasion)	-
5.11.6 (Outsole hardness)	-
5.11.7 (Outsole flexing)	-

-
Chem- Complete, Material declaration required for Innocuousness test. Mech- Except Cold Flex Resistance as per Cl. 5.5.5

9757

International Testing Centre, MSME Technology Development Centre, Meerut

8177804

IS 10702 (2023)

Hawai Chappal-Specification

39000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Material)	-	1000	-
4.2(Length)	-	300	-
4.3(Thickness)	-	300	-
4.4 , Table No. 1 , i)(Density)	-	300	-
4.4 , Table No. 1 , ii)(2Compression set at constant stress)	-	500	-
4.4 , Table No. 1 , iii)(3Split tear strength)	-	500	-
4.4 , Table No. 1 , iv)("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber")	-	500	-
4.4 , Table No. 1 , v)(5Abrasion resistance at applied force)	-	500	-
4.4 , Table No. 1 , vi)(Flexing resistance: Maximum cut growth at 50 000 flexes)	-	500	-
4.4 , Table No. 1 , vii)(7 Hydrolysis resistance, Maximum cut growth at 50 000 flexes)	-	1500	-
4.4 , Table No . 2 , i)(Density , Solid strap, Cellular strap)	-	300	-
4.4 , Table No . 2 , ii)("Breaking strength , Strap to strap and Toe portion to strap , Elongation at break")	-	500	-
4.4 , Table No . 2 , iii)(Minimum cross section of the stud)	-	300	-
4.4 , Table No . 3 , i)(Toe post attachment strength)	-	500	-
4.4 , Table No . 3 , ii)(Attachment strength of rear strap)	-	500	-
4.4 , Table No . 3 , iii)(Inter layer bond strength)	-	500	-
5(CHEMICAL REQUIREMENT FOR HAWAI CHAPPAL)	-	35000	-
Cl. No.5.1,Table no.1 of IS 17011(i)(Allergenic and carcinogenic disperse dyes)	-	8000	-
Cl. No.5.1,Table no.1 of IS 17011(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	8000	-
Cl. No.5.1,Table no.1 of IS 17011(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	8000	-
Cl. No.5.1,Table no.1 of IS 17011(iv)(Chromium (VI))	-	1000	-
Cl. No.5.1,Table no.1 of IS 17011(v)(Dimethyl fumarate (DMFU))	-	5000	-
Cl. No.5.1,Table no.1 of IS 17011(vi)(Formaldehyde (free or released by partial hydrolysis))	-	800	-
Cl. No.5.1,Table no.1 of IS 17011(vii)(Formaldehyde)	-	800	-
Cl. No.5.1,Table no.1 of IS 17011(viii)(Organotin compounds)	-	4500	-
Cl. No.5.1,Table no.1 of IS 17011(ix)(PCP-TeCP-TriCP polychlorophenols)	-	4500	-
Cl. No.5.1,Table no.1 of IS 17011(x)(pH)	-	500	-
Cl. No.5.1,Table no.1 of IS 17011(xi)(Phthalates (each individual phthalate))	-	4500	-
Cl. No.5.1,Table no.1 of IS 17011(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	800	-
Cl.No. 5.2(lead content)	-	1000	-
Clause 4.1 - 4.1.1(Bottom Material)	-	1500	-
Clause 4.1 - 4.1.2(Strap Material)	-	1000	-
Clause 4.1 - 4.1.3(Material)	-	1000	-
Clause 4.1 - 4.1.4(Material)	-	1000	-
Clause 4.2(Material)	-	1000	-
Clause 4.3 - 4.3.1(Thickness)	-	300	-
Clause 4.3 - 4.3.2(Thickness)	-	300	-
Clause 4.4 Table 1 -i)(Density, g/cm3, Min)	-	300	-
Clause 4.4 Table 1 -iii)(Split tear strength, kg, Min)	-	500	-
Clause 4.4 Table 1 -iv) - a("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, percent, Max")	-	500	-
Clause 4.4 Table 1 -iv) - b(Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber, percent, Max)	-	500	-
Clause 4.4 Table 1 -v)(Abrasion resistance at applied force 5 N)	-	800	-
Clause 4.4 Table 2 -i) - a("Density, g/cm3 Solid strap ")	-	300	-
Clause 4.4 Table 2 -i) - b(Density, g/cm3 Cellular strap)	-	300	-
Clause 4.4 Table 2 -ii) - a - 1("Breaking strength, kgf, Min Strap to strap(Solid Strap)")	-	500	-
Clause 4.4 Table 2 -ii) - a - 2("Breaking strength, kgf, Min Strap to strap(Cellular Strap)")	-	500	-
Clause 4.4 Table 2 -ii) - a - 3("Breaking strength, kgf, Min Toe portion to strap(Solid Strap)")	-	500	-
Clause 4.4 Table 2 -ii) - a - 4("Breaking strength, kgf, Min Toe portion to strap(Cellular Strap)")	-	500	-
Clause 4.4 Table 2 -ii) - b - 1("Elongation at break, percent (Applicable to strap to strap (V shape) Solid Strap")	-	500	-
Clause 4.4 Table 2 -ii) - b - 2("Elongation at break, percent (Applicable to strap to strap (V shape) Cellular Strap")	-	500	-
Clause 4.4 Table 2 -iii) - a("Minimum cross section of the stud, mm, Size 1 to 13 (Adult)")	-	500	-
Clause 4.4 Table 2 -iii) - b("Minimum cross section of the stud, mm, Size 3 to 13 (Children)")	-	500	-
Clause 4.4 Table 2 -iv) - a("Stud bolt, mm Diameter/edge to edge length")	-	300	-
Clause 4.4 Table 2 -iv) - b("Stud bolt, mm Thickness")	-	300	-
Clause 4.4 Table 3 -i)("Toe post attachment strength, N, Min")	-	500	-
Clause 4.4 Table 3 -ii)("Attachment strength of rear strap, N, Min")	-	500	-
Clause 4.4 Table 3 -iii)("Inter layer bond strength, N/mm, Min")	-	500	-

15 Apr, 2027

-
-

9758

Central Institute of Petrochemicals Engineering & Technology (CIPET), CSTS - Dehradun

9178004

IS 16205 : Part 24 (2017)

Conduit Systems for Cable Management part 24 Particular Requirements Conduit Systems Buried Under Ground

20350.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1.1(Classification - Resistance to Compression)	-	1600.00	Test Charge- 1100.00 specimen Charge- 500.00
6.1.2(Classification - Resistance to Impact)	-	1600.00	Test Charge- 1100.00 specimen Charge- 500.00
6.1.3(Classification - Resistance to Bending)	-	2000.00	-
6.5 of IS 16205 (Part 1) : 2017(Classification - According to Resistance to Flame Propogation)	-	3650.00	Spread of Fire 750 Spread of Fire Glow Wire 2900
14.0(External Influences)	-	10000.00	-
15.0(Electromagnetic Compatibility)	-	500.00	-
8 Table 101(Dimensions)	-	500.00	-
9.1 of IS 16205 (Part 1) : 2017(Construction)	-	500	-
6.1.4 of IS 16205 (Part 1) : 2017(Classification - Tensile Strength)	-	0.00	-
6.1.5 of IS 16205 (Part 1) : 2017(Classification - Suspended Load Capacity)	-	0.00	-
6.3 of IS 16205 (Part 1) : 2017(Classification - According to Electrical Characteristics)	-	0.00	-
6.4 of IS 16205 (Part 1) : 2017(Classification - According to Resistance to External Influences)	-	0.00	-
7.1(Marking and Documentation)	-	0.00	-
7.1.2(Marking and Documentation)	-	0.00	-
7.1.3(Marking and Documentation)	-	0.00	-
7.1.101(Marking and Documentation)	-	0.00	-
7.2(Marking and Documentation)	-	0.00	-
7.5 of IS 16205 (Part 1) : 2017(Marking and Documentation)	-	0.00	-
7.6 of IS 16205 (Part 1) : 2017(Marking and Documentation)	-	0.00	-
7.101(Marking and Documentation)	-	0.00	-
7.102(Marking and Documentation)	-	0.00	-
8 Table 101(Dimensions)	-	0.00	-
9.2 of IS 16205 (Part 1) : 2017(Construction)	-	0.00	-
9.4 of IS 16205 (Part 1) : 2017(Construction)	-	0.00	-
9.5 of IS 16205 (Part 1) : 2017(Construction)	-	0.00	-
9.6 of IS 16205 (Part 1) : 2017(Construction)	-	0.00	-
10.1(Mechanical Strength)	-	0.00	-
10.2(Compression Test)	-	0.00	-
10.3(Impact Test)	-	0.00	-
10.4(Bending Test)	-	0.00	-
13.1.3(Spread of fire)	-	0.00	-
13.1.3.1(Spread of fire)	-	0.00	-
13.1.3.2(Spread of fire)	-	0.00	-
14.2 of IS 16205 (Part 1) : 2017(Resistance against corrosion)	-	0.00	-
15(Mech)(Electromagnetic Compatibility)	-	0.00	-
14.2 of IS 16205 (Part 1) : 2017(Mech)(Resistance against corrosion)	-	0.00	-
14(Mech)(External Influences)	-	0.00	-
13.1.3.2(Mech)(Spread of fire)	-	0.00	-
13.1.3.1(Mech)(Spread of fire)	-	0.00	-
10.4(Mech)(Bending Test)	-	0.00	-
10.3(Mech)(Impact Test)	-	0.00	-
10.2(Mech)(Compression Test)	-	0.00	-
10.1(Mech)(Mechanical Strength )	-	0.00	-
9.6 of IS 16205 (Part 1) : 2017(Mech)(Construction)	-	0.00	-
9.5 of IS 16205 (Part 1) : 2017(Mech)(Construction)	-	0.00	-
9.4 of IS 16205 (Part 1) : 2017(Mech)(Construction)	-	0.00	-
9.2 of IS 16205 (Part 1) : 2017(Mech)(Construction)	-	0.00	-
9.1 of IS 16205 (Part 1) : 2017(Mech)(Construction)	-	0.00	-
8 Table 101(Mech)(Dimensions)	-	0.00	-
8 Table 101(Mech)(Dimensions)	-	0.00	-
7.102(Mech)(Marking and Documentation)	-	0.00	-
7.5 of IS 16205 (Part 1) : 2017(Mech)(Marking and Documentation)	-	0.00	-
7.2(Mech)(Marking and Documentation)	-	0.00	-
7.1.101(Mech)(Marking and Documentation)	-	0.00	-
7.1.3(Mech)(Marking and Documentation)	-	0.00	-
7.1.2(Mech)(Marking and Documentation)	-	0.00	-
7.1(Mech)(Marking and Documentation)	-	0.00	-
6.5 of IS 16205 (Part 1) : 2017(Mech)(Classification - According to Resistance to Flame Propogation)	-	0.00	-
6.4 of IS 16205 (Part 1) : 2017(Mech)(Classification - According to Resistance to External Influences)	-	0.00	-
6.3 of IS 16205 (Part 1) : 2017(Mech)(Classification - According to Electrical Characteristics)	-	0.00	-
6.1.5 of IS 16205 (Part 1) : 2017(Mech)(Classification - Suspended Load Capacity)	-	0.00	-
6.1.4 of IS 16205 (Part 1) : 2017(Mech)(Classification - Tensile Strength)	-	0.00	-
6.1.3(Mech)(Classification - Resistance to Bending)	-	0.00	-
6.1.2(Mech)(Classification - Resistance to Impact)	-	0.00	-
6.1.1 (Mech)(Classification - Resistance to Compression)	-	0.00	-
13.1.3(Mech)(Spread of fire)	-	0.00	-
7.101(Mech)(Marking and Documentation)	-	0.00	-
7.6 of IS 16205 (Part 1) : 2017(Mech)(Marking and Documentation)	-	0.00	-

24 Apr, 2027

-
-

9759

BIS, Eastern Regional Laboratory (ERL)

None

IS 17043 (2018)

Derby shoes - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.5.5.1 (Electrical Properties Antistatic )	-
5.0 (Innocuosness test IS 17011)	-

-
Chem - Excluding Allergenic & Carcinogenic Dyes, Organotin Compounds, Polychlorophenols Mech- Tag retention (Cl 4.15.2), Pull out test of eyelet (Cl 4.14)

9760

BIS, Eastern Regional Laboratory (ERL)

None

IS 17012 (2018)

High ankle tactical boots with pu - Rubber sole - Specification

For all design and size

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.5.5 (Antistatic test)	-
5.0 (Innocuousness Test IS 17011)	-
4.2 (Design )	-
4.3.1 (Size)	-
4.3.2 (Weight)	-
4.4 (Height of upper )	-
4.5.1 (Construction)	-
4.5.2 (Ergonomic Feature)	-
4.5.3.1 (Upper/outsole bond strength)	-
4.5.3.2 (Interayer bond strength)	-
4.6.1 (Thickness )	-
4.6.2 (Tear Strength)	-
4.6.3 (Water Penetration and water absorption )	-
4.7.1 (Material vamp & Quarter)	-
4.7.3 (Tear Strength)	-
4.7.4 (Abrasion resistance )	-
4.7.5 (Water Vapour permeability & coefficient )	-
4.8 (Thickness Toe puff & counter stiffener)	-
4.9.1 (Thickness)	-
4.9.2 (Abrasion resistance )	-
4.9.3 (Water absorption & desorption percent)	-
4.10.2 (Abrasion resistance )	-
4.10.3 (Water absorption & desorption percent)	-
4.11.1 (Thickness )	-
4.11.2 (Tear Strength)	-
4.12.1 (Thickness )	-
4.12.2 (Tear Strength)	-
4.13 (Breaking Strength of thread )	-
4.14.2 (Thickness)	-
4.14.3 (Sole Density )	-
4.14.4 (Tear Strength)	-
4.14.5 (Abrasion resistance )	-
4.14.6 (Hardness (IRHD))	-
4.14.7 (Ageing test)	-
4.14.8 (Flexing resistance )	-
4.14.9 (Resistance to hot contact )	-
4.15 (D-ring & Hooks )	-
4.16.1 (Length of lace )	-
4.16.2 (Breaking Strength of lace )	-
4.5.4 (Slip Resitance)	-

-
Chem- Complete, Material declaration required for Innocuousness test. Mech- Complete

9761

PIONEER TESTING LABORATORY PRIVATE LIMITED

8176806

IS 446 (2017)

Rubber hoses, textile - Reinforced, for compressed air - Specification (Fifth Revision)

All Type

14800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.3(Cut Lengths)	-	300	-
5.2(Thickness of Cover)	-	300	-
5.2(Thickness of Lining)	-	300	-
5.1, Table-1(Internal Diameter)	-	300	-
7.2, Table 3(Low temperature Flexibility)	-	2000	-
7.2, Table 3(Flexibility at 23°C)	-	1500	-
7.2, Table 3(Ozone Resistance)	-	2500	-
7.2, Table 3(Adhesion between Components- Cover and Reinforcement)	-	1000	-
7.2, Table 3(Adhesion between Components- Reinforcement layers)	-	1000	-
7.2, Table 3(Adhesion between Components- Lining and Reinforcement)	-	1000	-
7.2, Table 3(Minimum Bursting Pressure for type 3)	-	2000	-
7.2, Table 3(Minimum Bursting Pressure for type 2)	-	2000	-
7.2, Table 3(Minimum Bursting Pressure for type 1)	-	2000	-
7.2, Table 3(Change in Diameeter at Maximum working Pressure)	-	2000	-
7.2, Table 3(Change in Length at Maximum working Pressure)	-	2000	-
7.2, Table 3(Proof Pressure at 23°C for type 3)	-	2000	-
7.2, Table 3(Proof Pressure at 23°C for type 2)	-	2000	-
7.2, Table 3(Proof Pressure at 23°C for type 1)	-	2000	-
7.1, Table 2(Resistance to Liquid , Increase in Volume (Class C only)-Cover)	-	750	-
7.1, Table 2(Resistance to Liquid , Increase in Volume (Class C only)-Lining)	-	750	-
7.1, Table 2(Resistance to Liquid , Increase in Volume (Class B only)-Lining)	-	750	-
7.1, Table 2(Accelerated Ageing for all types: Change in Elongation of Cover of its original value)	-	2000	-
7.1, Table 2(Accelerated Ageing for all types: Change in Elongation of Lining of its original value)	-	2000	-
7.1, Table 2(Accelerated Ageing for all types: Change in Tensile Strength of Cover of its original value)	-	2000	-
7.1, Table 2(Accelerated Ageing for all types: Change in Tensile Strength of Lining of its original value)	-	2000	-
7.1, Table 2(Elongation at Break of Cover of all types)	-	1000	-
7.1, Table 2(Elongation at Break of Lining of all types)	-	1000	-
7.1, Table 2(Tensile Strength of Cover)	-	1000	-
7.1, Table 2(Tensile Strength of Lining)	-	1000	-
6, Dimensions(Thickness of Cover of Type 3)	-	300	-
6, Dimensions(Thickness of Cover of Type 2)	-	300	-
6, Dimensions(Thickness of Cover of Type 1)	-	300	-
6, Dimensions(Thickness of Lining of Type 3)	-	300	-
6, Dimensions(Thickness of Lining of Type 2)	-	300	-
6, Dimensions(Thickness of Lining of Type 1)	-	300	-
6, Dimensions(Tolerance on Length)	-	300	-
6, Dimensions(Concentricity)	-	300	-
6, Dimensions(Internal Diameter)	-	300	-
5(Material and Construction)	-	1000	-
Cl 4(Classification)	-	500	-

10 Mar, 2027

-
-

9762

PIONEER TESTING LABORATORY PRIVATE LIMITED

8176806

IS 937 (1981)

Specification for Washers For Water Fittings For Fire Fighting Purposes

All Type

9600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.1(Hardness of Rubber before & after Ageing)	-	2000	-
2.1(Elongation at Break before & after Ageing)	-	4500	-
2.1()	-	4500	-
2.1(Acid & Alkali Resistant Test)	-	2500	-
4.1(Size & Dimension)	-	200	-
5.1(Workmanship and Finish)	-	200	-
6.1(Marking)	-	200	-
2.2(Leather - IS 581)	-	0	-

10 Mar, 2027

-
-

9763

PIONEER TESTING LABORATORY PRIVATE LIMITED

8176806

IS 291 (1989)

Naval brass rods and sections for machining purposes - Specification (Third Revision)

All Type

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No.5(CONDITION)	-	200	-
Cl. No.6(FREEDOM FROM DEFECTS)	-	500	-
Cl. No.7.1(Sizes)	-	500	-
Cl. No.7.2(Tolerances)	-	200	-
Cl. No.8, Table no. 1(CHEMICAL COMPOSITION)	-	2400	-
Cl. No.9, Table no. 2(Tensile properties)	-	1500	-
Cl. No.10(MERCUROUS NITRATE TEST)	-	700	-
Cl. No.14(MARKING)	-	200	-

10 Mar, 2027

-
-

9764

BIS, Central Laboratory (CL)

None

IS 648 (2022)

Cold rolled non-oriented electrical steel sheet and strip - Fully processed type - Specification Sixth Revision

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. No. 8.1 (Thickness for CRNO Strips)	-
Cl. No. 8.2 (Width Tolerance for CRNO strips)	-
Cl. No. 8.3 (Length Tolerance for CRNO strips)	-
Cl. No. 8.6 (Flatness (Wavefactor) for CRNO strips)	-
Cl. No. 9.2 & Table-1 (Ductility (Bend test) for CRNO Strips)	-

-
Grade/Designation or Element to be tested may be declared with specified requirement. Exclusion : All Except Dimension

9765

Central Institute of Petrochemicals Engineering & Technology (CIPET), CSTS - Dehradun

9178004

IS 11652 (2017)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg cement – Specification (third revision)

27680.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2 (width of tape, 2.5 mm ± 0.1 mm)	-	500.00	-
4.1(Raw Material )	-	1050.00	Optional ( Applicable on Raw material)
4.2 (Linear Density, 900 denier)	-	500.00	Optional ( Applicable on Raw material)
4.3(Sacks)	-	500.00	-
4.4(Seam )	-	1850.00	Visual 300 Dimensions 250 Material identification 1050 Denier of stitching material 250
4.5(Lamination )	-	1350.00	Visual 300 Material identification 1050
4.6(Capacity The sack shall have the nominal filling capacity of 50 kg)	-	500.00	-
4.7(Valve for Filling of Sacks)	-	500.00	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note )- Annex B c) Width of gusset (e) 76 ± 10 mm )	-	500.00	-
Fig. 1- Table 1- Sr. no. ii (Ends per dm - Annex B 40 ± 2 )	-	500.00	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) Non-gusseted type 70 + 6%)	-	500.00	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): -1969 (Part 1) a) Lengthwise , 900 (91.8) )	-	2200.00	-
5/5.3-Table 1-Sr. no.vi(Breaking strength of bottom seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	2200.00	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) a) Lengthwise 15 to 25)	-	0.00	Breaking strength & Elongation have shingle Charge.
5/5.4-Table 1-Sr. no.viii(Drop impact strength - Annex C No failure)	-	1100.00	-
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D a) For UV stabilized sacks 2.2 )	-	1200.00	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to b) Accelerated Weathering - Annex F )	-	12380.00	Testing Charge- 2200.00 Conditioning Charge- 10180
Fig. 1- Table 1-Sr. no. iii (Picks per dm-Annex B 40 ± 2 )	-	500.00	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note )- Annex B c) Width of gusset (e) 76 ± 10 mm )	-	0.00	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B d) Width of valve (v) 100, + 10/-5 mm )	-	0.00	-
Fig. 1- Table 1-Sr. no. i (Dimensions, mm (see Note )- Annex B b) Width of sack (w) 480 ± 10 mm )	-	0.00	-
Fig. 1, Table 1 (i) Dimensions, mm (see Note ) -Annex B a) Length of sack, inside (l), 710 ± 10 mm )	-	0.00	-
4.5(and the remaining overhang shall not be more than 5 mm after trimming.)	-	0.00	-
4.2 (Fabric)	-	0.00	-
4.2 (The woven fabric shall be of mesh, 10 × 10 per inch)	-	0.00	-
4.2 (The woven fabric shall be of weight, 79 g/m2 )	-	0.00	-
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: a) ± 10 percent on individual value, and )	-	0.00	-
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: b) ± 5 percent on average. )	-	0.00	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0.00	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0.00	-
4.4(Seam )	-	0.00	-
4.4(Seam The two rows of stitches shall be separated from each other by minimum 5 mm and )	-	0.00	-
4.4(Seam The outer stitch shall be minimum 8 mm from the outer edge of the sacks. )	-	0.00	-
4.4(Seam The stitching shall be done with double fold over seam to)	-	0.00	-
4.4(to a depth of minimum 25 mm, so that so that)	-	0.00	-
4.4(that the stitches pass through a minimum of six layers of the fabric.)	-	0.00	-
4.4(The number of stitches/dm shall be 14 ± 2.)	-	0.00	-
4.4(Seam)	-	0.00	-
4.4(The material used for stitching shall be HDPE/PP tape having minimum 20 percent higher denier than the tapes used in the fabric.)	-	0.00	-
4.4(Seam)	-	0.00	-
4.4(Seam)	-	0.00	-
4.5(Lamination )	-	0.00	-
4.5(Lamination )	-	0.00	-
4.7(There shall be a double fold at the top seam and)	-	0.00	-
4.7(and then stitching shall be done through six layers.)	-	0.00	-
4.7(The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and)	-	0.00	-
4.7(and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0.00	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) gusseted type 71 + 6%)	-	0.00	-
5/5.1(The mass of bale of sacks (excluding packing materials) shall be within ± 3 percent of the mass calculated by multiplying the number of sacks with the mass of sack specified in Table 1.)	-	0.00	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): - 1969 (Part 1) b) Widthwise , 900 (91.8) )	-	0.00	-
5/5.3-Table 1-Sr. no.vi(Breaking strength of top seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	0.00	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) b) Widthwise 15 to 25)	-	0.00	-
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D b) For non-UV stabilized sacks 6 )	-	0.00	-
5/5.6 (UV Resistance, )	-	0.00	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to a) UV Radiation -Annex F )	-	0.00	-
4.2 (width of tape, 2.5 mm ± 0.1 mm)	-	0.00	-
Fig. 1- Table 1- Sr. no. ii (Ends per dm - Annex B 40 ± 2 )	-	0.00	-
Fig. 1- Table 1-Sr. no. iii (Picks per dm-Annex B 40 ± 2 )	-	0.00	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B d) Width of valve (v) 100, + 10/-5 mm )	-	0.00	-
Fig. 1- Table 1-Sr. no. i (Dimensions, mm (see Note )- Annex B b) Width of sack (w) 480 ± 10 mm )	-	0.00	-
Fig. 1, Table 1 (i) Dimensions, mm (see Note ) -Annex B a) Length of sack, inside (l), 710 ± 10 mm )	-	0.00	-
4.5(and the remaining overhang shall not be more than 5 mm after trimming.)	-	0.00	-
4.1(Raw Material )	-	0.00	-
4.2 (Fabric)	-	0.00	-
4.2 (Linear Density, 900 denier)	-	0.00	-
4.2 (The woven fabric shall be of mesh, 10 × 10 per inch)	-	0.00	-
4.2 (The woven fabric shall be of weight, 79 g/m2 )	-	0.00	-
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: a) ± 10 percent on individual value, and )	-	0.00	-
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: b) ± 5 percent on average. )	-	0.00	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0.00	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0.00	-
4.3(Sacks)	-	0.00	-
4.4(Seam )	-	0.00	-
4.4(Seam )	-	0.00	-
4.4(Seam The two rows of stitches shall be separated from each other by minimum 5 mm and )	-	0.00	-
4.4(Seam The outer stitch shall be minimum 8 mm from the outer edge of the sacks. )	-	0.00	-
4.4(Seam The stitching shall be done with double fold over seam to)	-	0.00	-
4.4(to a depth of minimum 25 mm, so that so that)	-	0.00	-
4.4(that the stitches pass through a minimum of six layers of the fabric.)	-	0.00	-
4.4(Seam)	-	0.00	-
4.4(The material used for stitching shall be HDPE/PP tape having minimum 20 percent higher denier than the tapes used in the fabric.)	-	0.00	-
4.4(Seam)	-	0.00	-
4.4(The number of stitches/dm shall be 14 ± 2.)	-	0.00	-
4.4(Seam)	-	0.00	-
4.4(Seam)	-	0.00	-
4.4(Seam)	-	0.00	-
4.5(Lamination )	-	0.00	-
4.5(Lamination )	-	0.00	-
4.5(Lamination )	-	0.00	-
4.6(Capacity The sack shall have the nominal filling capacity of 50 kg)	-	0.00	-
4.7(Valve for Filling of Sacks)	-	0.00	-
4.7(There shall be a double fold at the top seam and)	-	0.00	-
4.7(and then stitching shall be done through six layers.)	-	0.00	-
4.7(The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and)	-	0.00	-
4.7(and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0.00	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) Non-gusseted type 70 + 6%)	-	0.00	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) gusseted type 71 + 6%)	-	0.00	-
5/5.1(The mass of bale of sacks (excluding packing materials) shall be within ± 3 percent of the mass calculated by multiplying the number of sacks with the mass of sack specified in Table 1.)	-	0.00	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): -1969 (Part 1) a) Lengthwise , 900 (91.8) )	-	0.00	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): - 1969 (Part 1) b) Widthwise , 900 (91.8) )	-	0.00	-
5/5.3-Table 1-Sr. no.vi(Breaking strength of top seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	0.00	-
5/5.3-Table 1-Sr. no.vi(Breaking strength of bottom seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	0.00	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) a) Lengthwise 15 to 25)	-	0.00	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) b) Widthwise 15 to 25)	-	0.00	-
5/5.4-Table 1-Sr. no.viii(Drop impact strength - Annex C No failure)	-	0.00	-
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D a) For UV stabilized sacks 2.2 )	-	0.00	-
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D b) For non-UV stabilized sacks 6 )	-	0.00	-
5/5.6 (UV Resistance, )	-	0.00	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to a) UV Radiation -Annex F )	-	0.00	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to b) Accelerated Weathering - Annex F )	-	0.00	-
4.2 (width of tape, 2.5 mm ± 0.1 mm)	-	0.00	-
Fig. 1- Table 1- Sr. no. ii (Ends per dm - Annex B 40 ± 2 )	-	0.00	-
Fig. 1- Table 1-Sr. no. iii (Picks per dm-Annex B 40 ± 2 )	-	0.00	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note )- Annex B c) Width of gusset (e) 76 ± 10 mm )	-	0.00	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B d) Width of valve (v) 100, + 10/-5 mm )	-	0.00	-
Fig. 1- Table 1-Sr. no. i (Dimensions, mm (see Note )- Annex B b) Width of sack (w) 480 ± 10 mm )	-	0.00	-
Fig. 1, Table 1 (i) Dimensions, mm (see Note ) -Annex B a) Length of sack, inside (l), 710 ± 10 mm )	-	0.00	-
4.5(and the remaining overhang shall not be more than 5 mm after trimming.)	-	0.00	-
4.1(Raw Material )	-	0.00	-
4.2 (Fabric)	-	0.00	-
4.2 (Linear Density, 900 denier)	-	0.00	-
4.2 (The woven fabric shall be of mesh, 10 × 10 per inch)	-	0.00	-
4.2 (The woven fabric shall be of weight, 79 g/m2 )	-	0.00	-
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: a) ± 10 percent on individual value, and )	-	0.00	-
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: b) ± 5 percent on average. )	-	0.00	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0.00	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0.00	-
4.3(Sacks)	-	0.00	-
4.4(Seam )	-	0.00	-
4.4(Seam )	-	0.00	-
4.4(Seam The two rows of stitches shall be separated from each other by minimum 5 mm and )	-	0.00	-
4.4(Seam The outer stitch shall be minimum 8 mm from the outer edge of the sacks. )	-	0.00	-
4.4(Seam The stitching shall be done with double fold over seam to)	-	0.00	-
4.4(to a depth of minimum 25 mm, so that so that)	-	0.00	-
4.4(that the stitches pass through a minimum of six layers of the fabric.)	-	0.00	-
4.4(The number of stitches/dm shall be 14 ± 2.)	-	0.00	-
4.4(Seam)	-	0.00	-
4.4(The material used for stitching shall be HDPE/PP tape having minimum 20 percent higher denier than the tapes used in the fabric.)	-	0.00	-
4.4(Seam)	-	0.00	-
4.4(Seam)	-	0.00	-
4.4(Seam)	-	0.00	-
4.5(Lamination )	-	0.00	-
4.5(Lamination )	-	0.00	-
4.5(Lamination )	-	0.00	-
4.6(Capacity The sack shall have the nominal filling capacity of 50 kg)	-	0.00	-
4.7(Valve for Filling of Sacks)	-	0.00	-
4.7(There shall be a double fold at the top seam and)	-	0.00	-
4.7(and then stitching shall be done through six layers.)	-	0.00	-
4.7(The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and)	-	0.00	-
4.7(and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0.00	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) Non-gusseted type 70 + 6%)	-	0.00	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) gusseted type 71 + 6%)	-	0.00	-
5/5.1(The mass of bale of sacks (excluding packing materials) shall be within ± 3 percent of the mass calculated by multiplying the number of sacks with the mass of sack specified in Table 1.)	-	0.00	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): -1969 (Part 1) a) Lengthwise , 900 (91.8) )	-	0.00	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): - 1969 (Part 1) b) Widthwise , 900 (91.8) )	-	0.00	-
5/5.3-Table 1-Sr. no.vi(Breaking strength of top seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	0.00	-
5/5.3-Table 1-Sr. no.vi(Breaking strength of bottom seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	0.00	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) a) Lengthwise 15 to 25)	-	0.00	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) b) Widthwise 15 to 25)	-	0.00	-
5/5.4-Table 1-Sr. no.viii(Drop impact strength - Annex C No failure)	-	0.00	-
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D a) For UV stabilized sacks 2.2 )	-	0.00	-
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D b) For non-UV stabilized sacks 6 )	-	0.00	-
5/5.6 (UV Resistance, )	-	0.00	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to a) UV Radiation -Annex F )	-	0.00	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to b) Accelerated Weathering - Annex F )	-	0.00	-
4.2 (width of tape, 2.5 mm ± 0.1 mm)	-	0.00	-
Cl-5 Fig. 1- Table 1- Sr. no. ii(Ends per dm - Annex B 40 ± 2)	-	0.00	-
Cl-5 Fig. 1- Table 1-Sr. no. iii(Picks per dm-Annex B 40 ± 2)	-	0.00	-
Cl-5, Fig. 1- Table 1- Sr. no. i(Dimensions, mm (see Note )- Annex B c) Width of gusset (e) 76 ± 10 mm)	-	0.00	-
Cl-5, Fig. 1- Table 1- Sr. no. i(Dimensions, mm (see Note ) -Annex B d) Width of valve (v) 100, + 10/-5 mm)	-	0.00	-
Cl-5, Fig. 1- Table 1-Sr. no. i(Dimensions, mm (see Note )- Annex B b) Width of sack (w) 480 ± 10 mm)	-	0.00	-
Cl-5, Fig. 1, Table 1(i) Dimensions, mm (see Note ) -Annex B a) Length of sack, inside (l), 710 ± 10 mm)	-	0.00	-
4.5(and the remaining overhang shall not be more than 5 mm after trimming.)	-	0.00	-
4.1(Raw Material )	-	0.00	-
4.2 (Fabric)	-	0.00	-
4.2 (Linear Density, 900 denier)	-	0.00	-
4.2 (The woven fabric shall be of mesh, 10 × 10 per inch)	-	0.00	-
4.2 (The woven fabric shall be of weight, 79 g/m2 )	-	0.00	-
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: a) ± 10 percent on individual value, and )	-	0.00	-
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: b) ± 5 percent on average. )	-	0.00	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0.00	-
4.3(Sacks)	-	0.00	-
4.4(Seam )	-	0.00	-
4.4(Seam )	-	0.00	-
4.4(Seam The two rows of stitches shall be separated from each other by minimum 5 mm and )	-	0.00	-
4.4(Seam The outer stitch shall be minimum 8 mm from the outer edge of the sacks. )	-	0.00	-
4.4(Seam The stitching shall be done with double fold over seam to)	-	0.00	-
4.4(that the stitches pass through a minimum of six layers of the fabric.)	-	0.00	-
4.4(The number of stitches/dm shall be 14 ± 2.)	-	0.00	-
4.4(Seam)	-	0.00	-
4.4(The material used for stitching shall be HDPE/PP tape having minimum 20 percent higher denier than the tapes used in the fabric.)	-	0.00	-
4.4(Seam)	-	0.00	-
4.4(Seam)	-	0.00	-
4.4(Seam)	-	0.00	-
4.5(Lamination )	-	0.00	-
4.5(Lamination )	-	0.00	-
4.5(Lamination )	-	0.00	-
4.6(Capacity The sack shall have the nominal filling capacity of 50 kg)	-	0.00	-
4.7(Valve for Filling of Sacks)	-	0.00	-
4.7(There shall be a double fold at the top seam and)	-	0.00	-
4.7(and then stitching shall be done through six layers.)	-	0.00	-
4.7(The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and)	-	0.00	-
4.7(and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0.00	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) Non-gusseted type 70 + 6%)	-	0.00	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) gusseted type 71 + 6%)	-	0.00	-
5/5.1(The mass of bale of sacks (excluding packing materials) shall be within ± 3 percent of the mass calculated by multiplying the number of sacks with the mass of sack specified in Table 1.)	-	0.00	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): -1969 (Part 1) a) Lengthwise , 900 (91.8) )	-	0.00	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): - 1969 (Part 1) b) Widthwise , 900 (91.8) )	-	0.00	-
5/5.3-Table 1-Sr. no.vi(Breaking strength of top seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	0.00	-
5/5.3-Table 1-Sr. no.vi(Breaking strength of bottom seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	0.00	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) a) Lengthwise 15 to 25)	-	0.00	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) b) Widthwise 15 to 25)	-	0.00	-
5/5.4-Table 1-Sr. no.viii(Drop impact strength - Annex C No failure)	-	0.00	-
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D a) For UV stabilized sacks 2.2 )	-	0.00	-
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D b) For non-UV stabilized sacks 6 )	-	0.00	-
5/5.6 (UV Resistance, )	-	0.00	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to a) UV Radiation -Annex F )	-	0.00	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to b) Accelerated Weathering - Annex F )	-	0.00	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0.00	-
4.4(to a depth of minimum 25 mm, so that so that)	-	0.00	-

24 Apr, 2027

-
-

9766

GIGA LABS, BENGALURU

6177526

IS/IEC 60947 : Part 2 (2016)

Low - Voltage switchgear and controlgear: Part 2 circuit - Breakers (First Revision)

Low-voltage switchgear and control gear;Circuit-breaker

625000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.3.4.4(Verification of dielectric withstand)	-	15000	-
8.3.5.4(Verification of dielectric withstand)	-	15000	-
8.3.7.4(Verification of dielectric withstand)	-	15000	-
8.3.7.8(Verification of dielectric withstand)	-	15000	-
8.3.8.6(verification of dielectric withstand (sequence VI))	-	15000	-
8.3.3.4(Mechanical operation and operational performance capability)	-	500000	-
8.3.6.4(verification of temperature-rise (sequence IV))	-	25000	-
8.3.8.7(Verification of temperature-rise)	-	25000	-

08 Apr, 2027

-
Exclusion: Cl.8.3.9 (Critical d.c. load current test), Cl.8.3.7.2 (Short-circuit at the selectivity limit current), Cl.8.3.7.6 ((stage 2) short circuit at 1.1 time the take-over current (sequence V)), Cl.8.3.7.7 (Short-circuit at ultimate short-circuit breaking capacity), Cl.8.3.6.5 (Short-circuit breaking capacity at maximum short-time withstand current), Cl.8.3.6.3 (Rated short-time withstand current), Cl.8.3.8.3 (Rated short-time withstand current)

9767

Central Institute of Petrochemicals Engineering & Technology (CIPET), CSTS - Dehradun

9178004

IS 15450 (2022)

Polyethylene-aluminium-polyethylene composite pressure pipes for hot and cold water supplies Specifications first revision of IS 15450

48550.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(MATERIALS)	-	500.00	Optional (Applicable on Raw material)
8(COLOUR)	-	500.00	-
9(DIMENSIONS OF PIPE)	-	1500.00	All dimension have single Charge- 1500.00
10(VISUAL APPEARANCE)	-	500.00	-
11.1(Density (Method of test as per Table 3))	-	700.00	-
11.2(Melt Flow Rate (Method of test as per Table 3))	-	1100.00	-
11.3(Overall Migration)	-	2200.00	Testing charge- 1700.00 Specimen Charge- 500.00
11.4(Thermal Stability to Oxidation (Method of test as per Table 3))	-	2200.00	-
11.5(Carbon Black Content and Dispersion (Method of test as per Table 3))	-	1625.00	CBC- 925.00 CBD- 700.00
11.6(Pigment Dispersion (For Coloured Pipes) (Method of test as per Table 3))	-	700.00	-
11.7(Resistance to Weathering)	-	14800.00	Elongation at Break 1100 Thermal stability Oxidation Induction Time 2200 Hydrostatic pressure test 80oC for 1000 h₹ 11000 Specimen Charge 250
11.8(Adhesion Test)	-	1600.00	Test Charge- 1100.00 Specimen Charge- 500.00
11.9(Apparent Tensile Strength of Pipe)	-	1800.00	Test Charge- 1300.00 Specimen Charge- 500.00
11.10(Minimum Burst Pressure)	-	1000.00	-
11.11(Hydraulic Characteristics)	-	8500.00	(i) Acceptance Test 27oC for 1 hr. - 1000 500 60oC for 10 hr. - 1700 (ii) Type Test 95oC for 170 h₹ - 4800 500
6(PRESSURE RATING)	-	0.00	ALREADY CHARGE TAKEN FOR ABOVE PARAMETER.
7(NOMINAL DIAMETERS)	-	0.00	ALREADY CHARGE TAKEN FOR ABOVE PARAMETER.
Table 3(Anti-oxidant (as per IS 2530))	-	0.00	ALREADY CHARGE TAKEN FOR ABOVE PARAMETER.
14(MARKING)	-	0.00	ALREADY CHARGE TAKEN FOR ABOVE PARAMETER.
5.1(MATERIALS)	-	0.00	ALREADY CHARGE TAKEN FOR ABOVE PARAMETER.
5.2.1(MATERIALS)	-	0.00	ALREADY CHARGE TAKEN FOR ABOVE PARAMETER.
5.2.1.1(The other constituents)	-	0.00	ALREADY CHARGE TAKEN FOR ABOVE PARAMETER.
5.3.1(UV Stabilizer)	-	0.00	ALREADY CHARGE TAKEN FOR ABOVE PARAMETER.
5.3.2(UV Stabilizer)	-	0.00	ALREADY CHARGE TAKEN FOR ABOVE PARAMETER.
5.4(Aluminium)	-	0.00	ALREADY CHARGE TAKEN FOR ABOVE PARAMETER.
5.5(REWORK Material)	-	0.00	ALREADY CHARGE TAKEN FOR ABOVE PARAMETER.
7(NOMINAL DIAMETERS)	-	0.00	ALREADY CHARGE TAKEN FOR ABOVE PARAMETER.
8(COLOUR)	-	0.00	ALREADY CHARGE TAKEN FOR ABOVE PARAMETER.
9.1(DIMENSIONS OF PIPE)	-	0.00	ALREADY CHARGE TAKEN FOR ABOVE PARAMETER.
9.2.1(Method of Measurements)	-	0.00	ALREADY CHARGE TAKEN FOR ABOVE PARAMETER.
9.3(Length of Straight Pipe)	-	0.00	ALREADY CHARGE TAKEN FOR ABOVE PARAMETER.
9.4(Coiling)	-	0.00	ALREADY CHARGE TAKEN FOR ABOVE PARAMETER.
10(VISUAL APPEARANCE)	-	0.00	ALREADY CHARGE TAKEN FOR ABOVE PARAMETER.
11.1(Density)	-	0.00	ALREADY CHARGE TAKEN FOR ABOVE PARAMETER.
11.3(Melt Flow Rate)	-	0.00	ALREADY CHARGE TAKEN FOR ABOVE PARAMETER.
11.3(Overall Migration)	-	0.00	ALREADY CHARGE TAKEN FOR ABOVE PARAMETER.
6(PRESSURE RATING)	-	0.00	-
11.4(Thermal Stability to Oxidation)	-	0.00	ALREADY CHARGE TAKEN FOR ABOVE PARAMETER.
11.5(Carbon Black Content and Dispersion)	-	0.00	ALREADY CHARGE TAKEN FOR ABOVE PARAMETER.
11.6(Pigment Dispersion (For Coloured Pipes))	-	0.00	ALREADY CHARGE TAKEN FOR ABOVE PARAMETER.
11.7(Resistance to Weathering)	-	0.00	ALREADY CHARGE TAKEN FOR ABOVE PARAMETER.
11.8(Adhesion Test)	-	0.00	ALREADY CHARGE TAKEN FOR ABOVE PARAMETER.
11.9(Apparent Tensile Strength of Pipe)	-	0.00	ALREADY CHARGE TAKEN FOR ABOVE PARAMETER.
11.1(Minimum Burst Pressure)	-	0.00	ALREADY CHARGE TAKEN FOR ABOVE PARAMETER.
11.11.1(Short Term Hydrostatic Tests)	-	0.00	ALREADY CHARGE TAKEN FOR ABOVE PARAMETER.
11.11.12(Long Term Hydrostatic Test)	-	0.00	ALREADY CHARGE TAKEN FOR ABOVE PARAMETER.
12.1(Type Test)	-	0.00	-

24 Apr, 2027

-
-

9768

The Synthetic and Art Silk Mills' Research Association (SASMIRA), MUMBAI

7175004

IS 17070 (2019)

Jute agrotextiles for growth of plant and suppression of weeds – Specification

5100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5 -Table 1 -(i)(Mass at 20 percent moisture regain)	-	400	-
5 -Table 1 -(ii)(Thickness)	-	200	-
5 -Table 1 -(iii)(Width)	-	200	-
5 -Table 1 -(iv)(Wide width tensile strength)	-	1500	-
5 -Table 1 -(v)(Tear strength)	-	500	-
5 -Table 1 -(vi)(Bursting strength)	-	400	-
5 -Table 1 -(vii)(Index Puncture resistance)	-	700	-
5-Table 1 -(ix)(Water permittivity)	-	700	-
5 -Table 1 -(viii)(Air permeability)	-	500	-
8(Marking)	-	0	-

14 Dec, 2026

-
-

9769

The Synthetic and Art Silk Mills' Research Association (SASMIRA), MUMBAI

7175004

IS 16718 (2021)

Textiles - Polypropylene Spun Bonded Non-Woven Crop Covers and Fruit Skirting Bags for Agricultural and Horticultural Applications - Specification (first revision)

18700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Raw Material)	-	500	-
5.2.2(Width of fabric)	-	200	-
5.4.2 -Table 1-(i)(Mango, Orange)	-	400	-
5.4.2 - Table 2 - (i)(Thickness)	-	200	-
5.4.2 - Table 2 - (ii)(Fabric mass)	-	200	-
5.4.2 - Table 2 - (iii)(Breaking strength)	-	500	-
5.4.2 - Table 2 - (iv)(Elongation at break)	-	0	-
5.4.2 - Table 2 - (v)(Trapezoid tear strength)	-	500	-
5.4.2 - Table 2 - (vi)(Air permeability)	-	500	-
5.4.2 - Table 2 - (viii)(UV stability test)	-	10500	-
5.4.2 - Table 2 - (ix)(Ash content)	-	800	-
5.4.2 - Table 2 - (x)(Index puncture resistance)	-	700	-
5.4.2 - Table 2 - (xi)(Water absorption capacity)	-	700	-
5.4.2 - Table 2 - (xii)(Colour)	-	400	-
5.4.2 -Table 1-(ii)(Banana bunch)	-	400	-
5.4.2 -Table 1-(iii)(Grape bunch)	-	400	-
5.4.2 -Table 1-(iv)(Pomegranate)	-	400	-
5.4.2 -Table 1-(v)(Papaya)	-	400	-
8.1.2(Marking)	-	0	-
5.4.2 - Table 2 - (vii)(water vapour permeability)	-	1000	-

14 Dec, 2026

-
-

9770

BIS, Central Laboratory (CL)

None

IS 5509 (2021)

Fire Retardant Plywood - Specification ( Third Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
12.1 Table - 2 (i) (Moisture content, percent, Max)	-
8.1 (Dimensions)	-

-
Exclusion : No testing facility for requirements (ii), (iii), (iv) as per table 2 of clause 12.1 Sample Test Parameter not available: Cl 11.4 Static Bending Strength Above 15 mm thickness, Cl 12 Flammability, Flame penetration, Rate of burning Existing Sample Size:1 Full Size Sheet For All Tests Sample Size without dimensional measurements:Length-1500 mm, width-1200

9771

CIPET: CENTRE FOR SKILLING AND TECHNICAL SUPPORT (CSTS) - (CIPET), AURANGABAD

7123534

IS 14885 (2022)

Polyethylene Pipes for the Supply of Gaseous Fuels ï¿½ Specification (First Revision)

559475 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2(Grade of material)	-	500	-
4.3(Nominal Diameter)	-	500	-
4.4(Colour)	-	500	-
5.1(Polyethylene compound)	-	6300	-
5.3(Anti-oxidant)	-	1500	-
5.4(U-V stabilizer)	-	2000	-
5.7(PE Compound Quality Evaluation)	-	400000	10000 HOURS HYDROSTATIC PRESSURE TEST
5.5(Effect of Gas condensate on the Hydrostatic strength)	-	5000	-
5.6(Resistance to Weathering)	-	50500	-
6.1(Out of Roundness (Ovality))	-	500	-
6.2(Wall thickness (Take 8 reading and Average will be repoted))	-	500	-
7(Finish)	-	500	-
8.1(Internal pressure creep rupture test for plain at 80 deg. C for 165h)	-	4000	-
8.1(Internal pressure creep rupture test for plain pipes at 20 deg. C for 100h)	-	4800	-
8.1(Internal pressure creep rupture test for plain pipes at 80 deg. C for 1000 h)	-	11000	-
8.2(Reversion Test)	-	1000	-
8.3(Density)	-	1325	700+625
8.6(Thermal Stability (Oxidation Induction Time))	-	2200	-
8.7(Volatile Matter Content)	-	600	-
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	1300	-
6.4(Length of Pipe)	-	500	-
8.4(Melt Flow Rate (MFR))	-	1100	-
8.5(Pigment Dispersion)	-	600	-
8.10(Slow Crack Growth Rate Test)	-	10800	165+500 HOURS HYDROSTATIC PRESSURE TEST
8.11(Squeeze-off)	-	1300	-
5.1, 5.7 Table 2(v) Water content1))	-	600	-
4.2(Grade of material)	-	0	-
4.3(Nominal Diameter)	-	0	-
4.4(Colour)	-	0	-
5.1(Polyethylene compound)	-	0	-
5.3(Anti-oxidant)	-	0	-
5.4(U-V stabilizer)	-	0	-
5.7(PE Compound Quality Evaluation)	-	0	-
5.5(Effect of Gas condensate on the Hydrostatic strength)	-	0	-
5.6(Resistance to Weathering)	-	0	-
6.1(Out of Roundness (Ovality))	-	0	-
6.2(Wall thickness (Take 8 reading and Average will be repoted))	-	0	-
7(Finish)	-	0	-
8.1(Internal pressure creep rupture test for plain at 80 deg. C for 165h)	-	0	-
8.1(Internal pressure creep rupture test for plain pipes at 20 deg. C for 100h)	-	0	-
8.1(Internal pressure creep rupture test for plain pipes at 80 deg. C for 1000 h)	-	0	-
8.2(Reversion Test)	-	0	-
8.3(Density)	-	0	-
8.6(Thermal Stability (Oxidation Induction Time))	-	0	-
8.7(Volatile Matter Content)	-	0	-
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	0	-
6.4(Length of Pipe)	-	0	-
8.4(Melt Flow Rate (MFR))	-	0	-
8.5(Pigment Dispersion)	-	0	-
8.10(Slow Crack Growth Rate Test)	-	0	-
8.11(Squeeze-off)	-	0	-
5.1, 5.7 Table 2(v) Water content1))	-	0	-
5.1, 5.7 Table 2(i) Conventional density (of base polymer))	-	0	-
5.1, 5.7 Table 2(ii) Melt flow rate (MFR))	-	0	-
5.1, 5.7 Table 2(iii) Thermal stability (oxidation induction time))	-	0	-
5.1, 5.7 Table 2(vi) Pigment dispersion)	-	0	-
5.1, 5.7 Table 3(iv) Resistance to slow crack growth rate)	-	0	-
5.3(Anti-Oxidant)	-	0	-
5.4(U.V. Stabilizer)	-	0	-
5.5(Effects of Gas Condensate on the Hydrostatic Strength)	-	0	-
5.6(ii) Hydraulic characteristics)	-	0	-
5.6(iii) Thermal stability (Oxidation induction time))	-	0	-
8.7(Volatile Matter Content)	-	0	-
6(Dimensions of pipes)	-	0	-
7(Finish)	-	0	-
8.1(Hydraulic Characteristics)	-	0	-
8.2(Reversion test)	-	0	-
8.3(Density)	-	0	-
8.4(Melt Flow Rate)	-	0	-
8.5(Pigment Dispersion)	-	0	-
8.6(Thermal Stability (Oxidation Induction Time))	-	0	-
8.9(Resistance to Weathering)	-	0	-
8.10(Slow Crack Growth Rate Test)	-	0	-
8.11(Squeeze-of)	-	0	-
10(Marking)	-	0	-
8.9(Resistance to Weathering)	-	0	-
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	0	-
6.1(Mean out side Diameter (For less than or equal to 25 mm- Average of 8 , For higher diameters average of 6))	-	0	-
5.1, 5.7 Table 2(iv) Volatile content)	-	0	-
4.2(Grade of material)	-	0	-
4.3(Nominal Diameter)	-	0	-
4.4(Colour)	-	0	-
5.1(Polyethylene compound)	-	0	-
5.3(Anti-oxidant)	-	0	-
5.4(U-V stabilizer)	-	0	-
5.7(PE Compound Quality Evaluation)	-	0	-
5.5(Effect of Gas condensate on the Hydrostatic strength)	-	0	-
5.6(Resistance to Weathering)	-	0	-
6.1(Out of Roundness (Ovality))	-	0	-
6.2(Wall thickness (Take 8 reading and Average will be repoted))	-	0	-
7(Finish)	-	0	-
8.1(Internal pressure creep rupture test for plain at 80 deg. C for 165h)	-	0	-
8.1(Internal pressure creep rupture test for plain pipes at 20 deg. C for 100h)	-	0	-
8.1(Internal pressure creep rupture test for plain pipes at 80 deg. C for 1000 h)	-	0	-
8.2(Reversion Test)	-	0	-
8.3(Density)	-	0	-
8.6(Thermal Stability (Oxidation Induction Time))	-	0	-
8.7(Volatile Matter Content)	-	0	-
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	0	-
6.4(Length of Pipe)	-	0	-
8.4(Melt Flow Rate (MFR))	-	0	-
8.5(Pigment Dispersion)	-	0	-
8.10(Slow Crack Growth Rate Test)	-	0	-
8.11(Squeeze-off)	-	0	-
5.1, 5.7 Table 2(v) Water content1))	-	0	-
5.1, 5.7 Table 2(i) Conventional density (of base polymer))	-	0	-
5.1, 5.7 Table 2(ii) Melt flow rate (MFR))	-	0	-
5.1, 5.7 Table 2(iii) Thermal stability (oxidation induction time))	-	0	-
5.1, 5.7 Table 2(vi) Pigment dispersion)	-	0	-
5.1, 5.7 Table 3(iv) Resistance to slow crack growth rate)	-	0	-
5.3(Anti-Oxidant)	-	0	-
5.4(U.V. Stabilizer)	-	0	-
5.5(Effects of Gas Condensate on the Hydrostatic Strength)	-	0	-
5.6(ii) Hydraulic characteristics)	-	0	-
5.6(iii) Thermal stability (Oxidation induction time))	-	0	-
8.7(Volatile Matter Content)	-	0	-
6(Dimensions of pipes)	-	0	-
7(Finish)	-	0	-
8.1(Hydraulic Characteristics)	-	0	-
8.2(Reversion test)	-	0	-
8.3(Density)	-	0	-
8.4(Melt Flow Rate)	-	0	-
8.5(Pigment Dispersion)	-	0	-
8.6(Thermal Stability (Oxidation Induction Time))	-	0	-
8.9(Resistance to Weathering)	-	0	-
8.10(Slow Crack Growth Rate Test)	-	0	-
8.11(Squeeze-of)	-	0	-
10(Marking)	-	0	-
8.9(Resistance to Weathering)	-	0	-
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	0	-
6.1(Mean out side Diameter (For less than or equal to 25 mm- Average of 8 , For higher diameters average of 6))	-	0	-
5.1, 5.7 Table 2(iv) Volatile content)	-	0	-
4.2(Grade of material)	-	0	-
4.3(Nominal Diameter)	-	0	-
4.4(Colour)	-	0	-
5.1(Polyethylene compound)	-	0	-
5.3(Anti-oxidant)	-	0	-
5.4(U-V stabilizer)	-	0	-
5.7(PE Compound Quality Evaluation)	-	0	-
5.5(Effect of Gas condensate on the Hydrostatic strength)	-	0	-
5.6(Resistance to Weathering)	-	0	-
6.1(Out of Roundness (Ovality))	-	0	-
6.2(Wall thickness (Take 8 reading and Average will be repoted))	-	0	-
7(Finish)	-	0	-
8.1(Internal pressure creep rupture test for plain at 80 deg. C for 165h)	-	0	-
8.1(Internal pressure creep rupture test for plain pipes at 20 deg. C for 100h)	-	0	-
8.1(Internal pressure creep rupture test for plain pipes at 80 deg. C for 1000 h)	-	0	-
8.2(Reversion Test)	-	0	-
8.3(Density)	-	0	-
8.6(Thermal Stability (Oxidation Induction Time))	-	0	-
8.7(Volatile Matter Content)	-	0	-
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	0	-
6.4(Length of Pipe)	-	0	-
8.4(Melt Flow Rate (MFR))	-	0	-
8.5(Pigment Dispersion)	-	0	-
8.10(Slow Crack Growth Rate Test)	-	0	-
8.11(Squeeze-off)	-	0	-
5.1, 5.7 Table 2(v) Water content1))	-	0	-
5.1, 5.7 Table 2(i) Conventional density (of base polymer))	-	0	-
5.1, 5.7 Table 2(ii) Melt flow rate (MFR))	-	0	-
5.1, 5.7 Table 2(iii) Thermal stability (oxidation induction time))	-	0	-
5.1, 5.7 Table 2(vi) Pigment dispersion)	-	0	-
5.1, 5.7 Table 3(iv) Resistance to slow crack growth rate)	-	0	-
5.3(Anti-Oxidant)	-	0	-
5.4(U.V. Stabilizer)	-	0	-
5.5(Effects of Gas Condensate on the Hydrostatic Strength)	-	0	-
5.6(ii) Hydraulic characteristics)	-	0	-
5.6(iii) Thermal stability (Oxidation induction time))	-	0	-
8.7(Volatile Matter Content)	-	0	-
6(Dimensions of pipes)	-	0	-
7(Finish)	-	0	-
8.1(Hydraulic Characteristics)	-	0	-
8.2(Reversion test)	-	0	-
8.3(Density)	-	0	-
8.4(Melt Flow Rate)	-	0	-
8.5(Pigment Dispersion)	-	0	-
8.6(Thermal Stability (Oxidation Induction Time))	-	0	-
8.9(Resistance to Weathering)	-	0	-
8.10(Slow Crack Growth Rate Test)	-	0	-
8.11(Squeeze-of)	-	0	-
10(Marking)	-	0	-
8.9(Resistance to Weathering)	-	0	-
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	0	-
6.1(Mean out side Diameter (For less than or equal to 25 mm- Average of 8 , For higher diameters average of 6))	-	0	-
5.1, 5.7 Table 2(iv) Volatile content)	-	0	-
4.2(Grade of material)	-	0	-
4.3(Nominal Diameter)	-	0	-
4.4(Colour)	-	0	-
5.1(Polyethylene compound)	-	0	-
5.3(Anti-oxidant)	-	0	-
5.4(U-V stabilizer)	-	0	-
5.7(PE Compound Quality Evaluation)	-	0	-
5.5(Effect of Gas condensate on the Hydrostatic strength)	-	0	-
5.6(Resistance to Weathering)	-	0	-
6.1(Out of Roundness (Ovality))	-	0	-
6.2(Wall thickness (Take 8 reading and Average will be repoted))	-	0	-
7(Finish)	-	0	-
8.1(Internal pressure creep rupture test for plain at 80 deg. C for 165h)	-	0	-
8.1(Internal pressure creep rupture test for plain pipes at 20 deg. C for 100h)	-	0	-
8.1(Internal pressure creep rupture test for plain pipes at 80 deg. C for 1000 h)	-	0	-
8.2(Reversion Test)	-	0	-
8.3(Density)	-	0	-
8.6(Thermal Stability (Oxidation Induction Time))	-	0	-
8.7(Volatile Matter Content)	-	0	-
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	0	-
6.4(Length of Pipe)	-	0	-
8.4(Melt Flow Rate (MFR))	-	0	-
8.5(Pigment Dispersion)	-	0	-
8.10(Slow Crack Growth Rate Test)	-	0	-
8.11(Squeeze-off)	-	0	-
5.1, 5.7 Table 2(v) Water content1))	-	0	-
5.1, 5.7 Table 2(i) Conventional density (of base polymer))	-	0	-
5.1, 5.7 Table 2(ii) Melt flow rate (MFR))	-	0	-
5.1, 5.7 Table 2(iii) Thermal stability (oxidation induction time))	-	0	-
5.1, 5.7 Table 2(vi) Pigment dispersion)	-	0	-
5.1, 5.7 Table 3(iv) Resistance to slow crack growth rate)	-	0	-
5.3(Anti-Oxidant)	-	0	-
5.4(U.V. Stabilizer)	-	0	-
5.5(Effects of Gas Condensate on the Hydrostatic Strength)	-	0	-
5.6(ii) Hydraulic characteristics)	-	0	-
5.6(iii) Thermal stability (Oxidation induction time))	-	0	-
8.7(Volatile Matter Content)	-	0	-
6(Dimensions of pipes)	-	0	-
7(Finish)	-	0	-
8.1(Hydraulic Characteristics)	-	0	-
8.2(Reversion test)	-	0	-
8.3(Density)	-	0	-
8.4(Melt Flow Rate)	-	0	-
8.5(Pigment Dispersion)	-	0	-
8.6(Thermal Stability (Oxidation Induction Time))	-	0	-
8.9(Resistance to Weathering)	-	0	-
8.10(Slow Crack Growth Rate Test)	-	0	-
8.11(Squeeze-of)	-	0	-
10(Marking)	-	0	-
8.9(Resistance to Weathering)	-	0	-
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	0	-
6.1(Mean out side Diameter (For less than or equal to 25 mm- Average of 8 , For higher diameters average of 6))	-	0	-
5.1, 5.7 Table 2(iv) Volatile content)	-	0	-

31 Dec, 2026

-
Included w.e.f 04.04.2024. 16 to 450 mm nominal diameter.

9772

Ahmedabad Textile Industry's Research Association (ATIRA), Ahmedabad

7173002

IS 17880 (2022)

Geosynthetics Polymer Gabions for Coastal and Waterways Protection Specification

58505 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4 .1(Classification of synthetic polymer rope gabions based on aperture size of netting used)	-	0	-
Clause 5.1 and 7.1 , Table 1, i(Mesh opening size, mm, nominal (with a tolerance of ± 5 percent))	-	400	-
Clause 5.1 and 7.1, Table 1, ii(Rope diameter, nominal, mm)	-	200	-
Clause 5.1 and 7.1, Table 1, iii(Linear density of the rope, ktex (with a tolerance of ± 10 percent))	-	400	-
Clause 5.1 and 7.1, Table 1, iv(Mass in kg per square meter of gabions, nominal (with a tolerance of ± 5 percent))	-	400	-
Clause 5.1 and 7.1, Table 1, v(Breaking strength of rope, Min, kN (For ropes with eye spliced terminations, the breaking strength shall be 90 percent of the given strength.))	-	800	-
Clause 5.1 and 7.1, Table 1, vii("Breaking strength after thermal stability at 45 °C for 3 hours, kN, Min (For ropes with eye spliced terminations, the breaking strength shall be 90 percent of the given strength. )")	-	965	-
Clause 5.1 and 7.1, Table 1, viii(Rope net strength, Min, kN/m (For ropes with eye spliced terminations, the breaking strength shall be 90 percent of the given strength.))	-	0	-
Clause 5.1 and 7.1, Table 1, x(Retention in breaking strength of rope after UV exposure, percent, Min)	-	40800	-
Clause 5.1 and 7.1, Table 1, xi(Retention in breaking strength after exposure to saline water cyclic corrosion test for 168 h)	-	13940	-
Clause 4 .1(Classification of synthetic polymer rope gabions based on aperture size of netting used)	-	0	-
Clause 6.2.3(Sizes of Synthetic Polymer Rope Gabion)	-	600	-

-
-

9773

Ahmedabad Textile Industry's Research Association (ATIRA), Ahmedabad

7173002

IS 17372 (2020)

Geosynthetics – Polymeric strip/geostrip used as soil reinforcement in retaining structures – Specification

137100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause No. 4.1(Geostrip Material)	-	400	-
Clause No. 4.2(PET geostrip weight)	-	200	-
Clause No. 5.2, Table 1 (i)(Ultimate tensile strength (kN) of Geostrips)	-	1500	-
Clause No. 5.2, Table 1 (ii)(UV resistance (500h), strength retained of Geostrips)	-	41500	-
Clause No. 5.2, Table 1 (iii)(Chemical resistance, strength retained after 72 h immersion of Geostrips)	-	16380	-
Clause No. 5.2, Table 1 (iv)(Width of Geostrips)	-	200	-
Clause No. 5.2, Table 1 (v)(Roll length of Geostrips)	-	200	-
CL 5.3.2(Resistance to hydrolysis)	-	38460	-
CL 5.3.2(Resistance to oxidation)	-	38460	-
5.2 Table 1(Ultimate Tensile Strength kN (MD))	-	0	-

-
-

9774

BIS, Central Laboratory (CL)

None

IS 3521 : Part 1 (2021)

Personal Fall Arrest Systems Specification Part 1 Full Body Harness Fourth Revision

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (General)	-
4.2 (Classification)	-
4.3 (Design and Construction)	-
4.6 (Static Strength)	-
4.8 (Static Suspension Test)	-
4.3.2.3 (No of stitches per cm)	-
4.3.2.4 (Flammability)	-

-
-

9775

BIS, Central Laboratory (CL)

None

IS 15381 (2021)

Fire Blanket - Specification ( First Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7 (Workmanship and Finish)	-
4.4 (Mass)	-
4.3 (Shape & Dimension)	-

-
Excluding Fire performance, Electrical resistance (Sample not received till date)

9776

The Synthetic and Art Silk Mills' Research Association (SASMIRA), MUMBAI

7175004

IS 17731 (2021)

Agro-Textiles Laminated Woven Orchard Protection Covers Specification

68500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause No. 7, Table 1, (i)(Thickness, mm, Min)	-	200	-
Clause no. 7, Table 1, (ii)(Mass, g/m2, Min)	-	200	-
Clause No. 7, Table 1, (iii) a("Average breaking strength of laminated woven orchard protection cover fabric (Strip method, 325 mm × 50 mm test piece with gauge length of 200 mm), N, Min, (a) Warpway")	-	500	-
Clause No. 7, Table 1, (iii) b("Average breaking strength of laminated woven orchard protection cover fabric (Strip method, 325 mm × 50 mm test piece with gauge length of 200 mm), N, Min, (b) Weftway")	-	500	-
Clause No. 7, Table 1, (iv)("Retention of breaking strength after UV exposure of 1000 h, percentage of original actual value (fabric), percent, Min")	-	60500	-
Clause No. 7, Table 1, (iv)("Retention of breaking strength after UV exposure of 1000 h, percentage of original actual value (fabric), percent, Min")	-	0	-
Clause No. 7, Table 1, (v)(Strain at maximum load, percent)	-	0	-
Clause No. 7, Table 1, (vi)("Impact failure load at 1524 mm drop, Min, gram force at 50 percent failure")	-	700	-
Clause No. 7, Table 1, (vii)(Reinforcement band strength, N, Min)	-	500	-
Clause No. 7, Table 1, (viii)(Ash content, percent, Max)	-	500	-
Clause No. 7, Table 1, (ix)(Total visible light transmission, percent)	-	700	-
Clause No. 7, Table 1, (x)(Light diffusion, percent)	-	700	-
Clause No. 7, Table 1, (xi)(Thermicity IR effectiveness, percent)	-	1800	-
Clause No. 4.1(Width and linear density of HDPE Tapes)	-	200	-
Clause No. 4.1.1(Heat shrinkage of HDPE Tapes)	-	500	-
Clause No. 6.1.1(Coating Lamination thickness, micron)	-	600	-
Clause No. 6.1.2(Sandwich lamination thickness , micron)	-	400	-
Clause No. 6.2(Joints/Seams)	-	0	-
Clause No. 6.3(Number and position of metal eyelets)	-	0	-
Clause No. 7.1(colour , texture and finish)	-	0	-

14 Dec, 2026

-
-

9777

PIONEER TESTING LABORATORY PRIVATE LIMITED

8176806

IS 6527 (1995)

Stainless steel wire rods - Specification (First Revision)

All Type

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8(Heat Treatment)	-	1000	-
Cl 9(Tensile & Hardness)	-	3000	-
Cl 10(Diameter & Out Of Round)	-	300	-
10 & 10.1, Dia over 20 mm (Out of round)	-	300	-
10 & 10.1, Dia over 20 mm (Size, Tolerance)	-	300	-
10 & 10.1, Dia over 16 mm upto 20 mm (Out of round)	-	300	-
10 & 10.1, Dia over 16 mm upto 20 mm (Size, Tolerance)	-	300	-
10 & 10.1, Dia over 9.5 mm upto 16 mm (Out of round)	-	300	-
10 & 10.1, Dia over 9.5 mm upto 16 mm (Size, Tolerance)	-	300	-
10 & 10.1, Dia- (5.5-9.5 mm)(Out of round)	-	300	-
10 & 10.1, Dia- (5.5-9.5 mm)(Size, Tolerance)	-	300	-
Cl. 9.2 Table 4(Hardness)	-	1500	-
Cl. 9 .1 Table 3(Elongation)	-	1000	-
Cl. 9 .1 Table 3(0.2 % Proof Stress )	-	1000	-
Cl. 6(Freedom from defects)	-	500	-
Cl. 10.1(Out of Round)	-	300	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4)(Carbon)	-	300	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4)(Silicon)	-	300	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4)(Manganese)	-	300	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4)(Nickel)	-	300	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4)(Chromium)	-	300	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4)(Sulphur)	-	300	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4)(Phosphorous)	-	300	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4)(Nitrogen)	-	300	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4)(Copper)	-	300	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4)(Molybdenum)	-	300	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4)(Niobium)	-	300	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4)(Titanium)	-	300	-
13(Corrosion resistance-IS 10461,Part-1 & 2)	-	5000	-
13(Corrosion Resistance - IS 10461)	-	5000	-
15(Marking)	-	200	-

10 Mar, 2027

-
-

9778

PIONEER TESTING LABORATORY PRIVATE LIMITED

8176806

IS 1659 (2004)

Block boards - Specification (Fourth Revision)

All Type

7750 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.2.6(Spot test - Annexure L)	-	1000	-
9.2.5(Modulus of elasticity - MINIMUM INDIVIDUAL - Annexure K)	-	700	-
9.2.5(Modulus of elasticity - AVERAGE - Annexure K)	-	700	-
9.2.5(Modulus of rupture - MINIMUM INDIVIDUAL - Annexure K)	-	700	-
9.2.5(Modulus of rupture - AVERAGE - Annexure K)	-	700	-
9.2.4(Mycological Test [for MR grade only] - Annexure J)	-	1500	-
9.2.3(Adhesion of Plies - Annexure H)	-	750	-
9.2.2 (Resistance to water - Annexure G, Annexure H [For MR Grade])	-	600	-
9.2.2 (Resistance to water - Annexure G, Annexure H [For BWP grade])	-	600	-
9.2.1(Dimensional Changes caused by humidity Change in local planeness - Annexure F)	-	500	-
9.2.1(Dimensional Changes caused by humidity - Delamination - Annexure F)	-	500	-
9.2.1(Dimensional Changes caused by humidity - Change in thickness - at 40% RH - Annexure F)	-	500	-
9.2.1(Dimensional Changes caused by humidity - Change in Thickness - at 90% RH - Annexure F)	-	500	-
9.2.1(Dimensional Changes caused by humidity - Change in Length - at 40% RH - Annexure F)	-	500	-
9.2.1(Dimensional Changes caused by humidity - Change in Length - at 90% RH - Annexure F)	-	500	-
7.3(Dimensional Requirements - Variation in thickness - Annexure E)	-	200	-
7.3(Dimensional Requirements - Squareness - Annexure D)	-	500	-
7.3(Dimensional Requirements - Edge Straightness - Annexure D)	-	500	-
7.3(Dimensional Requirements - Thickness - Annexure E)	-	200	-
7.3(Dimensional Requirements - Width - 8.1.4)	-	200	-
7.3(Dimensional Requirements - Length - 8.1.4)	-	200	-
8.1.3, 6.3.3, IS 1328(Visual Inspection - Permissible Defects - IS 1328 [test method for DECORATIVE type])	-	200	-
8.1.3, 6.3.3, IS 303(Visual Inspection - Permissible Defects - IS 303 [test method for COMMERCIAL type])	-	200	-
9.2.6 (mechanical)(Spot test - Annexure L)	-	1000	-
cl. 11(marking)	-	200	-

10 Mar, 2027

-
-

9779

PIONEER TESTING LABORATORY PRIVATE LIMITED

8176806

IS 1237 (2012)

Cement Concrete Flooring Tiles - Specification

All Type

7200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 7.1(Length, Breadth, Minimum thickness, Difference in length of side between the longest side and shorterst side, Half tiles, Difference in Thickness between the thickest and thinnest tile, Thickness of wearing layer)	-	1200	-
Cl 12.2(Concavity & Convexity )	-	500	-
Cl 12.3(The Maximum gap between the arms of the square and the edge of the title shall notexceed 2 percent of the length.)	-	500	-
Cl 12.4(Shall not exceed 1 percent of the length of the edge.)	-	500	-
Cl 12.5(Water absorption)	-	1000	-
Cl 12.6(Wet transverse strength )	-	1500	-
Cl 12.7(Resistance to wear)	-	1500	-
Cl 11(Suface Finish)	-	500	-

10 Mar, 2027

-
-

9780

CENTRAL INSTITUTE OF PETROCHEMICALS ENGINEERING & TECHNOLOGY (CIPET) : IPT-BHUBANESWAR

5102634

IS 6192 (2023)

Textiles Monoaxially oriented high density polyethylene HDPE and polypropylene PP tapes Specification

Pigmented/Unpigmented tapes

25138 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(MATERIAL(Refer IS 7328 :1974))	-	1150.00	-
5.1(Linear density (For test method Refer IS 6193:1971 and IS 7703 Part 1))	-	525	-
5.2(Tenacity (For test method Refer IS 6193:1971))	-	825	-
5.3(Elongation (For test method Refer IS 6193:1971))	-	975	-
5.4(Finished width (For test method Refer IS 6193:1971))	-	375	-
5.5(Thickness (For test method Refer IS 6193:1971))	-	375	-
5.6(Heat Shrinkage at 60 degree C(For test method Refer IS 6193:1971) )	-	1275	-
5.6(Heat Shrinkage at 95 degree C(For test method Refer IS 6193:1971) )	-	0	-
5.7( pigmented tapes(Refer IS 2454))	-	19638	-
4(MATERIAL(Refer IS 7328 :1974))	-	0.00	-
5.1(Linear density (For test method Refer IS 6193:1971 and IS 7703 Part 1))	-	0.00	-
5.2(Tenacity (For test method Refer IS 6193:1971))	-	0.00	-
5.3(Elongation (For test method Refer IS 6193:1971))	-	0.00	-
5.4(Finished width (For test method Refer IS 6193:1971))	-	0	-
5.5(Thickness (For test method Refer IS 6193:1971))	-	0.00	-
5.6(Heat Shrinkage at 60 degree C(For test method Refer IS 6193:1971) )	-	0.00	-
5.6(Heat Shrinkage at 95 degree C(For test method Refer IS 6193:1971) )	-	0.00	-
5.7( pigmented tapes(Refer IS 2454))	-	0.00	-
Cl-4.1(High Density Polyethylene Tapes)	-	0	-
Cl-4.2(Polypropylene Tapes)	-	0	-
Cl-5.1.8(Ash Content)	-	0	-
Cl-6.1(Marking)	-	0	-
Cl-5.1.1(Finished tape width)	-	0	-
Cl-5.1.2(Thickness of the tape)	-	0	-
Cl-5.1.3(Linear density of tape)	-	0	-
Cl-5.1.4(Polypropylene Tapes)	-	0	-
Cl-5.1.5(Average value of the elongation at break of tape)	-	0	-
Cl-5.1.6(UV radiation exposure)	-	0	-
Cl-5.1.7(Average heat shrinkage of HDPE tapes)	-	0	-
Cl-5.1.6(UV stabilized HDPE and PP resins)	-	0	-
Cl-4.1(High Density Polyethylene Tapes)	-	0	-
Cl-4.2(Polypropylene Tapes)	-	0	-
Cl-5.1.8(Ash Content)	-	0	-
Cl-6.1(Marking)	-	0	-
Cl-5.1.1(Finished tape width)	-	0	-
Cl-5.1.2(Thickness of the tape)	-	0	-
Cl-5.1.3(Linear density of tape)	-	0	-
Cl-5.1.4(Polypropylene Tapes)	-	0	-
Cl-5.1.5(Average value of the elongation at break of tape)	-	0	-
Cl-5.1.6(UV radiation exposure)	-	0	-
Cl-5.1.7(Average heat shrinkage of HDPE tapes)	-	0	-
Cl-5.1.6(UV stabilized HDPE and PP resins)	-	0	-
Cl-4.1(High Density Polyethylene Tapes)	-	0	-
Cl-4.2(Polypropylene Tapes)	-	0	-
Cl-5.1.8(Ash Content)	-	0	-
Cl-6.1(Marking)	-	0	-
Cl-5.1.1(Finished tape width)	-	0	-
Cl-5.1.2(Thickness of the tape)	-	0	-
Cl-5.1.3(Linear density of tape)	-	0	-
Cl-5.1.4(Polypropylene Tapes)	-	0	-
Cl-5.1.5(Average value of the elongation at break of tape)	-	0	-
Cl-5.1.6(UV radiation exposure)	-	0	-
Cl-5.1.7(Average heat shrinkage of HDPE tapes)	-	0	-
Cl-5.1.6(UV stabilized HDPE and PP resins)	-	0	-
Cl-4.1(High Density Polyethylene Tapes)	-	0	-
Cl-4.2(Polypropylene Tapes)	-	0	-
Cl-5.1.8(Ash Content)	-	0	-
Cl-6.1(Marking)	-	0	-
Cl-5.1.1(Finished tape width)	-	0	-
Cl-5.1.2(Thickness of the tape)	-	0	-
Cl-5.1.3(Linear density of tape)	-	0	-
Cl-5.1.4(Polypropylene Tapes)	-	0	-
Cl-5.1.5(Average value of the elongation at break of tape)	-	0	-
Cl-5.1.6(UV radiation exposure)	-	0	-
Cl-5.1.7(Average heat shrinkage of HDPE tapes)	-	0	-
Cl-5.1.6(UV stabilized HDPE and PP resins)	-	0	-

31 Dec, 2026

-
Included w.e.f.03.07.2025 Exclusion Cl 4.3

Bureau of Indian Standards

The National Standards Body of India

Search by IS Number