| 9871 |
Intertek India Private Limited (289-290), Gurugram
| 8166336
| IS 16289 (2014) |
Medical textiles - Surgical face masks - Specification |
Medical textiles - Surgical face masks |
40000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 4.2 Table 1 i)(Bacterial Filtration Efficiency) |
- |
7900 |
|
- |
| 4.2 Table 1 ii)(Differential Pressure) |
- |
6700 |
|
- |
| 4.2 Table 1 iii)(Splash Resistance) |
- |
17500 |
|
- |
| 4.2 Table 1 iv)(Sub-micron particulate filtration efficiency at 0.1 µ) |
- |
7900 |
|
- |
| 4.1.1(Materials and Construction) |
- |
1000 |
|
- |
| 4.1.2(Design) |
- |
1000 |
|
- |
| 4.2 Table 1 i)(Bacterial Filtration Efficiency) |
- |
7900 |
|
- |
| 4.2 Table 1 ii)(Differential Pressure) |
- |
6700 |
|
- |
| 4.2 Table 1 iii)(Splash Resistance) |
- |
17500 |
|
- |
|
- |
-
- |
| 9872 |
Intertek India Private Limited (289-290), Gurugram
| 8166336
| IS 15354 : Part 1 (2018) |
Single - Use medical examination gloves: Part 1 specification for gloves made from rubber latex or rubber solution (First Revision) |
Single - Use medical examination gloves |
14300.00 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 6.1 & Table 2(Width corresponding to size code (dimension w,Figure 1)) |
- |
500 |
|
- |
| 6.2(Watertightness) |
- |
700 |
|
- |
| 6.3.2 & Table 3(Minimum force at break before accelerated ageing) |
- |
550 |
|
- |
| 6.3.2 & Table 3(Minimum Elongation at break before accelerated ageing) |
- |
550 |
|
- |
| 6.3.3 & Table 3(Minimum force at break after accelerated ageing) |
- |
2550 |
|
- |
|
- |
-
- |
| 9873 |
Intertek India Private Limited (289-290), Gurugram
| 8166336
| IS 13422 (1992) |
Disposable surgical rubber gloves specification |
Disposable surgical rubber gloves |
10350 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 5.2.1(General Characteristics and Dimensions) |
- |
500 |
|
- |
| 5.3 and Table 2( Tensile Strength Before Ageing) |
- |
550 |
|
- |
| 5.3 and Table 2( Tensile StrengthAfter Accelerated Ageing) |
- |
2550 |
|
- |
| 5.4(Sterility) |
- |
0 |
|
- |
| 5.5(Airtight Test) |
- |
700 |
|
- |
| 5.3 and Table 2( Elongation at Break Before Ageing) |
- |
550 |
|
- |
| 5.3 and Table 2( Elongation at Break After Accelerated Ageing) |
- |
2550 |
|
- |
| 5.2.2 and Table 1
Fig. 1(Dimensions - Length) |
- |
500 |
|
- |
| 5.2.2 and Table 1
Fig. 1(Dimensions - Width) |
- |
500 |
|
- |
| 5.2.2 and Table 1
Fig. 1(Dimensions - Thickness of Finger) |
- |
500 |
|
- |
| 5.2.2 and Table 1
Fig. 1(Dimensions - Thickness of Palm) |
- |
500 |
|
- |
| 5.2.2 and Table 1
Fig. 1(Dimensions - Thickness of Cuff) |
- |
500 |
|
- |
| 5.3 and Table 2(Stress at 500% Elongation at Break Before Ageing) |
- |
550 |
|
- |
| 5.2.3(thickness) |
- |
500 |
|
- |
|
- |
-
Exclusion: Cl.5.4 (Sterility) |
| 9874 |
Intertek India Private Limited (289-290), Gurugram
| 8166336
| IS 9873 : Part 9 (2017) |
Safety of Toys Part 9 Certain Phthalates Esters in Toys and Children's Products |
- |
30000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 3.0(Vinyl in toys or childcare articles - a) Bis-(2-ethlyhexyl) Phthalates (DEHP), b) Di-Butyl phthalate (DBP), c) Benzyl butyl Phthalate (BBP) - IS 9873 Part 6) |
- |
4000 |
|
4000 /component |
| 3.0(Vinyl in any part of the toy or childcare article that can be placed in mouth of a child under 4 years of age - a) Di-iso-Nonyl Phthalate (DINP), b) Di-iso-Decyl Phthalate (DIDP), c) Di-n-Octyl Phthalate (DNOP) - IS 9873 Part 6) |
- |
4000 |
|
4000 /component |
| 3.0(Vinyl in toys or childcare articles - a) Bis-(2-ethlyhexyl) Phthalates (DEHP), b) Di-Butyl phthalate (DBP), c) Benzyl butyl Phthalate (BBP) - IS 9873 Part 6) |
- |
4000 |
|
4000 /component |
| 3.0(Vinyl in any part of the toy or childcare article that can be placed in mouth of a child under 4 years of age - a) Di-iso-Nonyl Phthalate (DINP), b) Di-iso-Decyl Phthalate (DIDP), c) Di-n-Octyl Phthalate (DNOP) - IS 9873 Part 6) |
- |
4000 |
|
4000 /component |
| 3.0(Vinyl in toys or childcare articles - a) Bis-(2-ethlyhexyl) Phthalates (DEHP), b) Di-Butyl phthalate (DBP), c) Benzyl butyl Phthalate (BBP) - IS 9873 Part 6) |
- |
4000 |
|
4000 /component |
| 3.0(Vinyl in any part of the toy or childcare article that can be placed in mouth of a child under 4 years of age - a) Di-iso-Nonyl Phthalate (DINP), b) Di-iso-Decyl Phthalate (DIDP), c) Di-n-Octyl Phthalate (DNOP) - IS 9873 Part 6) |
- |
4000 |
|
4000 /component |
| 3.0(Vinyl in toys or childcare articles - a) Bis-(2-ethlyhexyl) Phthalates (DEHP), b) Di-Butyl phthalate (DBP), c) Benzyl butyl Phthalate (BBP) - IS 9873 Part 6) |
- |
4000 |
|
4000 /component |
| 3.0(Vinyl in any part of the toy or childcare article that can be placed in mouth of a child under 4 years of age - a) Di-iso-Nonyl Phthalate (DINP), b) Di-iso-Decyl Phthalate (DIDP), c) Di-n-Octyl Phthalate (DNOP) - IS 9873 Part 6) |
- |
4000 |
|
4000 /component |
|
- |
-
- |
| 9875 |
Intertek India Private Limited (289-290), Gurugram
| 8166336
| IS 9873 : Part 7 (2017) |
Safety of toys: Part 7 requirements and test methods for finger paints |
- |
38480 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 4.2.1 (Colourants used in finger paint shall not have any of the health hazard classifications set out in
4.1 (hazard class 3.1 to 3.10) - ISO 8124) |
- |
2640 |
|
2640/- per component |
| 4.2.2 - Table 1, 2(Finger Paint shall not contain Azo colourants that by cleavage of one or more azo groups can produce the primary aromatic amines - Annex C) |
- |
2640 |
|
2640/- per component |
| 4.3 - Annex - D- Table D.1 - Ref 1(Preservatives - Benzoic acid,
sodium benzoate (as acid) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 2(Preservatives - Ammonium benzoate
calcium benzoate, potassium benzoate, magnesium benzoate, MEA-benzoate, methyl benzoate, ethyl benzoate, propyl benzoate, butyl benzoate, isobutyl benzoate, isopropyl benzoate,
phenyl benzoate (as acid) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 3(Preservatives - Propionic acid,, ammonium propionate, calcium propionate, magnesium propionate, potassium propionate, sodium propionate (as acid) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 4(Preservatives - Hexa-2,4-dienoic acid and its
salts: Sorbic acid, calcium sorbate, sodium sorbate
potassium sorbate (as acid) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 5(Preservatives - Paraformaldehyde (free-formaldehyde)- EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 6(Preservatives - Biphenyl-2-ol (o-Phenylphenol), sodium o-phenylphenate, potassium o-phenylphenate, MEA o-phenylphenate (expressed as the phenol) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 7(Preservatives - Pyrithione zinc - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 8(Preservatives - Inorganic sulfites and hydrogen-sulfites: Sodium sulfite, ammonium bisulfite, ammonium sulfite, potassium sulfite, potassium, hydrogen sulfite, sodium bisulfite, sodium metabisulfite, potassium metabisulfite (as free SO2) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 9(Preservatives - Chlorobutanol - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 10(Preservatives -4-Hydroxybenzoic acid, methylparaben, potassium ethylparaben, potassium paraben, sodium methylparaben, sodium ethylparaben, ethylparaben, sodium paraben, potassium methylparaben, calcium paraben, phenylparaben (as acid) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 11(Preservatives - 3-Acetyl-6-methylpyran-2,4
(3H)-dione and its salts: Dehydroacetic acid, sodium dehydroacetate (as acid) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 12(Preservatives - Formic acid, sodium formate (as acid) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 13(Preservatives - 3,3’-Dibromo-4,4’-hexamethylenedioxydi-benzamidine and its salts (including isethionate) (Dibromohexamidine isethionate) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 14(Preservatives - Undec-10-
enoic acid and its salts: Undecylenic acid, potassium undecylenate, sodium undecylenate, calcium undecylenate, TEA-undecylenate, MEA-undecylenate (as acid) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 15(Preservatives - 5- Pyrimidinamine, 1,3-
bis (2-ethylhexyl)-5- methylhexahydropyrimidin-5-amine (Hexetidine) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 16(Preservatives - 2-Bromo-2-nitropropane-1,3-diol (Bronopol) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 17(Preservatives - 2,4-Dichlorobenzyl alcohol - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 18(Preservatives - 1-(4-Chlorophenyl)-3-(3,4-dichlorophenyl) urea (Triclocarban) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 19(Preservatives - 5-Chloro-2- (2,4- dichlorophenoxy) phenol (Triclosan) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 20(Preservatives - Chloroxylenol - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 21(Preservatives -N,N″-methylenebis[N′-[3-(hydroxymethyl)-2,5-dioxoimidazolidin-4-yl]urea] (Imidazolidinyl urea) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 22(Preservatives -Poly(methylene),.alpha.,.omega.-bis[[[(aminoiminomethyl)
amino]iminomethyl] amino]-,
dihydrochloride (Polyaminopropyl biguanide) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 23(Preservatives - 2-Phenoxyethanol - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 24(Preservatives - Methenamine - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 25(Preservatives - Methenamine-3-chloro-allylochloride
(Quaternium-15) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 26(Preservatives -1-(4-Chlorophenoxy)-1-(imidazol-1-yl)-3,3-dimethylbutan-2-one (Climbazole)
- EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 27(Preservatives - 1,3-Bis (hydroxymethyl)-5,5-dimethylimidazolidine-2,4-dione (DMDM
Hydantoin) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 28(Preservatives - 1-Hydroxy-4-methyl-6-(2,4,4-
trimethylpentyl) 2-pyridon
and its monoethanolamine salt
(Piroctone Olamine) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 29(Preservatives - 2,2’-methylenebis(6-bromo-4-chlorophenol) (Bromochlorophene) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 30(Preservatives - 4-Isopropyl-m-cresol (o-Cymen-5-ol)
- EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 31(Preservatives - Mixture of 5-Chloro-2-methyl-isothiazol-3(2H)-one and 2-methylisothiazol-3(2H)-one with magnesium chloride and magnesium nitrate (of a mixture in the ratio 3:1 of 5-chloro-2-methylisothiazol 3(2H)-one and 2-methylisothiazol-3 (2H)-one) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 32(Preservatives - 2-methylisothiazol-3(2H)-one
(MIT) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 33(Preservatives - 2-Benzyl-4-chlorophenol (Chlorophene) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 34(Preservatives - 2-Chloroacetamide - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 35(Preservatives - N,N″-bis(4-chlorophenyl)-3,12-diimino-2,4,11,13-tetraazatetradecanediamidine and
its digluconate, diacetate and
dihydrochloride: Chlorhexidine, Chlorhexidine Diacetate, Chlorhexidine Digluconate
Chlorhexidine Dihydrochloride (as chlorhexidine)
- EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 36(Preservatives - Alkyl (C 12–22) trimethyl
ammonium bromide and chloride: Behentrimonium chloride, cetrimonium bromide, cetrimonium chloride, laurtrimonium bromide, laurtrimonium chloride, steartrimonium bromide, steartrimonium chloride - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 37(Preservatives - 4,4-Dimethyl-1,3-oxazolidine - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 38(Preservatives - N-(Hydroxymethyl)-N-(dihydroxymethyl-1,3-dioxo-2,5-imidazolidinyl-4)-N’-(hydroxymethyl) urea (Diazolidinyl Urea) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 39(Preservatives -Benzenecarboximidamide,
4,4’-(1,6-hexanediyl-bis-(oxy))-bis-(3-nitrobenzamidine) and its salts (including
isethionate and phydroxybenzoate):
hexamidine, hexamidine diisethionate,
hexamidine paraben - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 40(Preservatives - Pentane-1,5-dial (Glutaraldehyde, Glutaral) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 41(Preservatives - 3-(p-Chlorophenoxy)-propane-1,2 diol (Chlorphenesin) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 42(Preservatives - Sodium N-hydroxymethyl-glycinate - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 43(Preservatives - Benzenemethanaminium, N,Ndimethyl-N-[2-[2-[4-(1,1,3,3,- tetramethylbutyl)phenoxy]
ethoxy] ethyl]-, chloride (Benzethonium Chloride)- EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.4 (ref. Table 1 row 3 of ISO 8124-3-2010)(Antimony (Sb) - Cl 7,8,9 of IS 9873-3 : 2017 and
ISO 8124-3 : 2010) |
- |
2640 |
|
2640/- per component |
| 4.4 (ref. Table 1 row 3 of ISO 8124-3-2010)(Arsenic (As) - Cl 7,8,9 of IS 9873-3 : 2017 and
ISO 8124-3 : 2010) |
- |
2640 |
|
2640/- per component |
| 4.4 (ref. Table 1 row 3 of ISO 8124-3-2010)(Barium (Ba) - Cl 7,8,9 of IS 9873-3 : 2017 and
ISO 8124-3 : 2010) |
- |
2640 |
|
2640/- per component |
| 4.4 (ref. Table 1 row 3 of ISO 8124-3-2010)(Cadmium (Cd) - Cl 7,8,9 of IS 9873-3 : 2017 and
ISO 8124-3 : 2010) |
- |
2640 |
|
2640/- per component |
| 4.4 (ref. Table 1 row 3 of ISO 8124-3-2010)(Chromium (Cr) - Cl 7,8,9 of IS 9873-3 : 2017 and
ISO 8124-3 : 2010) |
- |
2640 |
|
2640/- per component |
| 4.4 (ref. Table 1 row 3 of ISO 8124-3-2010)(Lead (Pb) - Cl 7,8,9 of IS 9873-3 : 2017 and
ISO 8124-3 : 2010) |
- |
2640 |
|
2640/- per component |
| 4.4 (ref. Table 1 row 3 of ISO 8124-3-2010)(Mercury (Hg) - Cl 7,8,9 of IS 9873-3 : 2017 and
ISO 8124-3 : 2010) |
- |
2640 |
|
2640/- per component |
| 4.4 (ref. Table 1 row 3 of ISO 8124-3-2010)(Selenium (Se) - Cl 7,8,9 of IS 9873-3 : 2017 and
ISO 8124-3 : 2010) |
- |
2640 |
|
2640/- per component |
| 4.5.1.1 - Table 1(Primary aromatic amines - Annex C) |
- |
2640 |
|
2640/- per component |
| 4.5.1.2 - Table 2(Individual carcinogenic primary aromatic amines - Annex C) |
- |
2640 |
|
2640/- per component |
| 4.5.1.2 - Table 2(Total,carcinogenic primary aromatic amines - Annex C) |
- |
2640 |
|
2640/- per component |
| 4.5.2 - Table 3(Impurities - Polychlorinated biphenyls - Annex C) |
- |
2640 |
|
2640/- per component |
| 4.5.2 - Table 3(IImpurities- Hexachlorobenzene - Annex C) |
- |
2640 |
|
2640/- per component |
| 4.5.2 - Table 3(Impurities - Benzo (α) pyrene - Annex C) |
- |
2640 |
|
2640/- per component |
| 4.6 - Table 4(Taste and smell - Finger paints shall not be sweetened, flavoured or fragranced - Cl 4.6) |
- |
2640 |
|
2640/- per component |
| 4.7(pH value - ISO 787-9) |
- |
2640 |
|
2640/- per component |
| 4.8(shall only use binding agents, extenders, humectants and surfactants which are not
classified with any of the health hazards set out in in 4.1 (hazards class 3.1 to 3.10)) |
- |
2640 |
|
2640/- per component |
| 4.9(N-Nitrosamines - N-nitrosodiethanolamine (NDELA) - n EN 71–12:2013, 7.2.1 and Clause 8) |
- |
2640 |
|
2640/- per component |
| 4.1(Container - Containers used for finger paints shall not have a design that is likely to be mistaken by children with containers of foodstuffs or drinks) |
- |
2640 |
|
2640/- per component |
| 4.2.1 (Colourants used in finger paint shall not have any of the health hazard classifications set out in
4.1 (hazard class 3.1 to 3.10) - ISO 8124) |
- |
2640 |
|
2640/- per component |
| 4.2.2 - Table 1, 2(Finger Paint shall not contain Azo colourants that by cleavage of one or more azo groups can produce the primary aromatic amines - Annex C) |
- |
2640 |
|
2640/- per component |
| 4.3 - Annex - D- Table D.1 - Ref 1(Preservatives - Benzoic acid,
sodium benzoate (as acid) - EU Cosmetics Legislation) |
- |
0.0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 2(Preservatives - Ammonium benzoate
calcium benzoate, potassium benzoate, magnesium benzoate, MEA-benzoate, methyl benzoate, ethyl benzoate, propyl benzoate, butyl benzoate, isobutyl benzoate, isopropyl benzoate,
phenyl benzoate (as acid) - EU Cosmetics Legislation) |
- |
0.0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 3(Preservatives - Propionic acid,, ammonium propionate, calcium propionate, magnesium propionate, potassium propionate, sodium propionate (as acid) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 4(Preservatives - Hexa-2,4-dienoic acid and its
salts: Sorbic acid, calcium sorbate, sodium sorbate
potassium sorbate (as acid) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 5(Preservatives - Paraformaldehyde (free-formaldehyde)- EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 6(Preservatives - Biphenyl-2-ol (o-Phenylphenol), sodium o-phenylphenate, potassium o-phenylphenate, MEA o-phenylphenate (expressed as the phenol) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 7(Preservatives - Pyrithione zinc - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 8(Preservatives - Inorganic sulfites and hydrogen-sulfites: Sodium sulfite, ammonium bisulfite, ammonium sulfite, potassium sulfite, potassium, hydrogen sulfite, sodium bisulfite, sodium metabisulfite, potassium metabisulfite (as free SO2) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 9(Preservatives - Chlorobutanol - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 10(Preservatives -4-Hydroxybenzoic acid, methylparaben, potassium ethylparaben, potassium paraben, sodium methylparaben, sodium ethylparaben, ethylparaben, sodium paraben, potassium methylparaben, calcium paraben, phenylparaben (as acid) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 11(Preservatives - 3-Acetyl-6-methylpyran-2,4
(3H)-dione and its salts: Dehydroacetic acid, sodium dehydroacetate (as acid) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 12(Preservatives - Formic acid, sodium formate (as acid) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 13(Preservatives - 3,3’-Dibromo-4,4’-hexamethylenedioxydi-benzamidine and its salts (including isethionate) (Dibromohexamidine isethionate) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 14(Preservatives - Undec-10-
enoic acid and its salts: Undecylenic acid, potassium undecylenate, sodium undecylenate, calcium undecylenate, TEA-undecylenate, MEA-undecylenate (as acid) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 15(Preservatives - 5- Pyrimidinamine, 1,3-
bis (2-ethylhexyl)-5- methylhexahydropyrimidin-5-amine (Hexetidine) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 16(Preservatives - 2-Bromo-2-nitropropane-1,3-diol (Bronopol) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 17(Preservatives - 2,4-Dichlorobenzyl alcohol - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 18(Preservatives - 1-(4-Chlorophenyl)-3-(3,4-dichlorophenyl) urea (Triclocarban) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 19(Preservatives - 5-Chloro-2- (2,4- dichlorophenoxy) phenol (Triclosan) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 20(Preservatives - Chloroxylenol - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 21(Preservatives -N,N″-methylenebis[N′-[3-(hydroxymethyl)-2,5-dioxoimidazolidin-4-yl]urea] (Imidazolidinyl urea) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 22(Preservatives -Poly(methylene),.alpha.,.omega.-bis[[[(aminoiminomethyl)
amino]iminomethyl] amino]-,
dihydrochloride (Polyaminopropyl biguanide) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 23(Preservatives - 2-Phenoxyethanol - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 24(Preservatives - Methenamine - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 25(Preservatives - Methenamine-3-chloro-allylochloride
(Quaternium-15) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 26(Preservatives -1-(4-Chlorophenoxy)-1-(imidazol-1-yl)-3,3-dimethylbutan-2-one (Climbazole)
- EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 27(Preservatives - 1,3-Bis (hydroxymethyl)-5,5-dimethylimidazolidine-2,4-dione (DMDM
Hydantoin) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 28(Preservatives - 1-Hydroxy-4-methyl-6-(2,4,4-
trimethylpentyl) 2-pyridon
and its monoethanolamine salt
(Piroctone Olamine) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 29(Preservatives - 2,2’-methylenebis(6-bromo-4-chlorophenol) (Bromochlorophene) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 30(Preservatives - 4-Isopropyl-m-cresol (o-Cymen-5-ol)
- EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 31(Preservatives - Mixture of 5-Chloro-2-methyl-isothiazol-3(2H)-one and 2-methylisothiazol-3(2H)-one with magnesium chloride and magnesium nitrate (of a mixture in the ratio 3:1 of 5-chloro-2-methylisothiazol 3(2H)-one and 2-methylisothiazol-3 (2H)-one) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 32(Preservatives - 2-methylisothiazol-3(2H)-one
(MIT) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 34(Preservatives - 2-Chloroacetamide - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 35(Preservatives - N,N″-bis(4-chlorophenyl)-3,12-diimino-2,4,11,13-tetraazatetradecanediamidine and
its digluconate, diacetate and
dihydrochloride: Chlorhexidine, Chlorhexidine Diacetate, Chlorhexidine Digluconate
Chlorhexidine Dihydrochloride (as chlorhexidine)
- EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 36(Preservatives - Alkyl (C 12–22) trimethyl
ammonium bromide and chloride: Behentrimonium chloride, cetrimonium bromide, cetrimonium chloride, laurtrimonium bromide, laurtrimonium chloride, steartrimonium bromide, steartrimonium chloride - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 37(Preservatives - 4,4-Dimethyl-1,3-oxazolidine - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 38(Preservatives - N-(Hydroxymethyl)-N-(dihydroxymethyl-1,3-dioxo-2,5-imidazolidinyl-4)-N’-(hydroxymethyl) urea (Diazolidinyl Urea) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 39(Preservatives -Benzenecarboximidamide,
4,4’-(1,6-hexanediyl-bis-(oxy))-bis-(3-nitrobenzamidine) and its salts (including
isethionate and phydroxybenzoate):
hexamidine, hexamidine diisethionate,
hexamidine paraben - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 40(Preservatives - Pentane-1,5-dial (Glutaraldehyde, Glutaral) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 41(Preservatives - 3-(p-Chlorophenoxy)-propane-1,2 diol (Chlorphenesin) - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 42(Preservatives - Sodium N-hydroxymethyl-glycinate - EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.3 - Annex - D- Table D.1 - Ref 43(Preservatives - Benzenemethanaminium, N,Ndimethyl-N-[2-[2-[4-(1,1,3,3,- tetramethylbutyl)phenoxy]
ethoxy] ethyl]-, chloride (Benzethonium Chloride)- EU Cosmetics Legislation) |
- |
0 |
|
Exclusion |
| 4.4 (ref. Table 1 row 3 of ISO 8124-3-2010)(Antimony (Sb) - Cl 7,8,9 of IS 9873-3 : 2017 and
ISO 8124-3 : 2010) |
- |
2640 |
|
2640/- per component |
| 4.4 (ref. Table 1 row 3 of ISO 8124-3-2010)(Arsenic (As) - Cl 7,8,9 of IS 9873-3 : 2017 and
ISO 8124-3 : 2010) |
- |
2640 |
|
2640/- per component |
| 4.4 (ref. Table 1 row 3 of ISO 8124-3-2010)(Barium (Ba) - Cl 7,8,9 of IS 9873-3 : 2017 and
ISO 8124-3 : 2010) |
- |
2640 |
|
2640/- per component |
| 4.4 (ref. Table 1 row 3 of ISO 8124-3-2010)(Cadmium (Cd) - Cl 7,8,9 of IS 9873-3 : 2017 and
ISO 8124-3 : 2010) |
- |
2640 |
|
2640/- per component |
| 4.4 (ref. Table 1 row 3 of ISO 8124-3-2010)(Chromium (Cr) - Cl 7,8,9 of IS 9873-3 : 2017 and
ISO 8124-3 : 2010) |
- |
2640 |
|
2640/- per component |
| 4.4 (ref. Table 1 row 3 of ISO 8124-3-2010)(Lead (Pb) - Cl 7,8,9 of IS 9873-3 : 2017 and
ISO 8124-3 : 2010) |
- |
2640 |
|
2640/- per component |
| 4.4 (ref. Table 1 row 3 of ISO 8124-3-2010)(Mercury (Hg) - Cl 7,8,9 of IS 9873-3 : 2017 and
ISO 8124-3 : 2010) |
- |
2640 |
|
2640/- per component |
| 4.4 (ref. Table 1 row 3 of ISO 8124-3-2010)(Selenium (Se) - Cl 7,8,9 of IS 9873-3 : 2017 and
ISO 8124-3 : 2010) |
- |
2640 |
|
2640/- per component |
| 4.5.1.1 - Table 1(Primary aromatic amines - Annex C) |
- |
2640 |
|
2640/- per component |
| 4.5.1.2 - Table 2(Individual carcinogenic primary aromatic amines - Annex C) |
- |
2640 |
|
2640/- per component |
| 4.5.1.2 - Table 2(Total,carcinogenic primary aromatic amines - Annex C) |
- |
2640 |
|
2640/- per component |
| 4.5.2 - Table 3(Impurities - Polychlorinated biphenyls - Annex C) |
- |
2640 |
|
2640/- per component |
| 4.5.2 - Table 3(IImpurities- Hexachlorobenzene - Annex C) |
- |
2640 |
|
2640/- per component |
| 4.5.2 - Table 3(Impurities - Benzo (α) pyrene - Annex C) |
- |
2640 |
|
2640/- per component |
| 4.6 - Table 4(Taste and smell - Finger paints shall not be sweetened, flavoured or fragranced - Cl 4.6) |
- |
2640 |
|
2640/- per component |
| 4.7(pH value - ISO 787-9) |
- |
2640 |
|
2640/- per component |
| 4.8(shall only use binding agents, extenders, humectants and surfactants which are not
classified with any of the health hazards set out in in 4.1 (hazards class 3.1 to 3.10)) |
- |
2640 |
|
2640/- per component |
| 4.9(N-Nitrosamines - N-nitrosodiethanolamine (NDELA) - n EN 71–12:2013, 7.2.1 and Clause 8) |
- |
2640 |
|
2640/- per component |
| 4.1(Container - Containers used for finger paints shall not have a design that is likely to be mistaken by children with containers of foodstuffs or drinks) |
- |
2640 |
|
2640/- per component |
|
- |
-
Exclusion: Cl.4.3 Annex D, Table D.1 |
| 9876 |
Intertek India Private Limited (289-290), Gurugram
| 8166336
| IS 9873 : Part 3 (2020) |
Safety of Toys Part 3 Migration of Certain Elements ( Third Revision ) |
Safety of Toys |
25000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 4.1 - Table 1(Antimony (Sb) - Cl 7,8,9 of IS 9873-3 : 2017 and
ISO 8124-3 : 2010) |
- |
2500 |
|
INR 2500/ material for complete all 8 HM. |
| 4.1 - Table 1(Arsenic (As) - Cl 7,8,9 of IS 9873-3 : 2017 and
ISO 8124-3 : 2010) |
- |
2500 |
|
INR 2500/ material for complete all 8 HM. |
| 4.1 - Table 1(Barium (Ba) - Cl 7,8,9 of IS 9873-3 : 2017 and
ISO 8124-3 : 2010) |
- |
2500 |
|
INR 2500/ material for complete all 8 HM. |
| 4.1 - Table 1(Cadmium (Cd) - Cl 7,8,9 of IS 9873-3 : 2017 and
ISO 8124-3 : 2010) |
- |
2500 |
|
INR 2500/ material for complete all 8 HM. |
| 4.1 - Table 1(Chromium (Cr) - Cl 7,8,9 of IS 9873-3 : 2017 and
ISO 8124-3 : 2010) |
- |
2500 |
|
INR 2500/ material for complete all 8 HM. |
| 4.1 - Table 1(Lead (Pb) - Cl 7,8,9 of IS 9873-3 : 2017 and
ISO 8124-3 : 2010) |
- |
2500 |
|
INR 2500/ material for complete all 8 HM. |
| 4.1 - Table 1(Mercury (Hg) - Cl 7,8,9 of IS 9873-3 : 2017 and
ISO 8124-3 : 2010) |
- |
2500 |
|
INR 2500/ material for complete all 8 HM. |
| 4.1 - Table 1(Selenium (Se) - Cl 7,8,9 of IS 9873-3 : 2017 and
ISO 8124-3 : 2010) |
- |
2500 |
|
INR 2500/ material for complete all 8 HM. |
| 4.1 - Table 1(Antimony (Sb) - Cl 7,8,9 of IS 9873-3 : 2017 and
ISO 8124-3 : 2010) |
- |
2500 |
|
INR 2500/ material for complete all 8 HM. |
| 4.1 - Table 1(Arsenic (As) - Cl 7,8,9 of IS 9873-3 : 2017 and
ISO 8124-3 : 2010) |
- |
2500 |
|
INR 2500/ material for complete all 8 HM. |
| 4.1 - Table 1(Barium (Ba) - Cl 7,8,9 of IS 9873-3 : 2017 and
ISO 8124-3 : 2010) |
- |
2500 |
|
INR 2500/ material for complete all 8 HM. |
| 4.1 - Table 1(Cadmium (Cd) - Cl 7,8,9 of IS 9873-3 : 2017 and
ISO 8124-3 : 2010) |
- |
2500 |
|
INR 2500/ material for complete all 8 HM. |
| 4.1 - Table 1(Chromium (Cr) - Cl 7,8,9 of IS 9873-3 : 2017 and
ISO 8124-3 : 2010) |
- |
2500 |
|
INR 2500/ material for complete all 8 HM. |
| 4.1 - Table 1(Lead (Pb) - Cl 7,8,9 of IS 9873-3 : 2017 and
ISO 8124-3 : 2010) |
- |
2500 |
|
INR 2500/ material for complete all 8 HM. |
| 4.1 - Table 1(Mercury (Hg) - Cl 7,8,9 of IS 9873-3 : 2017 and
ISO 8124-3 : 2010) |
- |
2500 |
|
INR 2500/ material for complete all 8 HM. |
| 4.1 - Table 1(Selenium (Se) - Cl 7,8,9 of IS 9873-3 : 2017 and
ISO 8124-3 : 2010) |
- |
2500 |
|
INR 2500/ material for complete all 8 HM. |
| 4.1 - Table 1(Selenium (Se) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010) |
- |
2500 |
|
INR 2500/ material for complete all 8 HM. |
| 4.1 - Table 1(Mercury (Hg) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010) |
- |
2500 |
|
INR 2500/ material for complete all 8 HM. |
| 4.1 - Table 1(Lead (Pb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010) |
- |
2500 |
|
INR 2500/ material for complete all 8 HM. |
| 4.1 - Table 1(Chromium (Cr) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010) |
- |
2500 |
|
INR 2500/ material for complete all 8 HM. |
| 4.1 - Table 1(Cadmium (Cd) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010) |
- |
2500 |
|
INR 2500/ material for complete all 8 HM. |
| 4.1 - Table 1(Barium (Ba) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010) |
- |
2500 |
|
INR 2500/ material for complete all 8 HM. |
| 4.1 - Table 1(Arsenic (As) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010) |
- |
2500 |
|
INR 2500/ material for complete all 8 HM. |
| 4.1 - Table 1(Antimony (Sb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010) |
- |
2500 |
|
INR 2500/ material for complete all 8 HM. |
| 4.1 - Table 1(Antimony (Sb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010) |
- |
2500 |
|
INR 2500/ material for complete all 8 HM. |
| 4.1 - Table 1(Arsenic (As) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010) |
- |
2500 |
|
INR 2500/ material for complete all 8 HM. |
| 4.1 - Table 1(Barium (Ba) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010) |
- |
2500 |
|
INR 2500/ material for complete all 8 HM. |
| 4.1 - Table 1(Cadmium (Cd) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010) |
- |
2500 |
|
INR 2500/ material for complete all 8 HM. |
| 4.1 - Table 1(Mercury (Hg) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010) |
- |
2500 |
|
INR 2500/ material for complete all 8 HM. |
| 4.1 - Table 1(Selenium (Se) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010) |
- |
2500 |
|
INR 2500/ material for complete all 8 HM. |
| 4.1 - Table 1(Chromium (Cr) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010) |
- |
2500 |
|
INR 2500/ material for complete all 8 HM. |
| 4.1 - Table 1(Lead (Pb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010) |
- |
2500 |
|
INR 2500/ material for complete all 8 HM. |
| 4.1(Sample preparation as per clause 8 of IS 9873 Part 3:1999) |
- |
2500 |
|
INR 2500/ material for complete all 8 HM. |
| Cl-4.1 & 4.2,Table 1,sl.no-i(Sb) |
- |
2500 |
|
INR 2500/ material for complete all 8 HM. |
| Cl-4.1 & 4.2,Table 1,sl.no-ii(As) |
- |
2500 |
|
INR 2500/ material for complete all 8 HM. |
|
- |
-
- |
| 9877 |
Intertek India Private Limited (289-290), Gurugram
| 8166336
| IS 9873 : Part 1 (2019) |
Safety of toys: Part 1 safety aspects related to mechanical and physical properties (Fourth Revision) |
- |
16500 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 4.2 - 5.24.2( Reasonably foreseeable abuse -Drop Test) |
- |
500 |
|
Charges for Drop Test |
| 4.2 - 5.24.3( Reasonably foreseeable abuse -Tip-over test for large and bulky toys) |
- |
500 |
|
- |
| 4.2 - 5.24.4( Reasonably foreseeable abuse -Dynamic strength test for wheeled ride-on toys other than toy scooters) |
- |
500 |
|
- |
| 4.2 - 5.24.5( Reasonably foreseeable abuse -Torque test) |
- |
500 |
|
- |
| 4.2 - 5.24.6.2( Reasonably foreseeable abuse -Tension test for seams in soft-filled (stuffed) toys. beanbag-type toys, and other similar filled toys) |
- |
500 |
|
- |
| 4.2 - 5.24.6.3( Reasonably foreseeable abuse -Tension test for pompoms) |
- |
500 |
|
- |
| 4.2 - 5.24.6.4( Reasonably foreseeable abuse -Tension test for protective components) |
- |
500 |
|
- |
| 4.2 - 5.24.6.5( Reasonably foreseeable abuse -Tension test for a projectile with a suction cup) |
- |
500 |
|
- |
| 4.2 - 5.24.7( Reasonably foreseeable abuse -Compression test) |
- |
500 |
|
- |
| 4.2 - 5.24.8.2( Reasonably foreseeable abuse-Flexure test-Wires and other metallic components intended to be bent) |
- |
500 |
|
- |
| 4.2 - 5.24.8.3( Reasonably foreseeable abuse -Flexure test-Wires likely to be bent) |
- |
500 |
|
- |
| 4.3.2 - 5.21( Expanding materials) |
- |
500 |
|
- |
| 4.4.1 - 5.2(Small parts-For children under 36 months) |
- |
500 |
|
- |
| 4.4.2 - 5.2(Small parts-For children 36 months and over but under 72 months
) |
- |
500 |
|
- |
| 4.5.1.2 - 5.3(Shape, size and strength of certain toys-Squeeze toys, rattles, and certain other toys and components of toys-Test for shape and size of certain toys) |
- |
500 |
|
- |
| 4.5.1.3 - 5.3(Shape, size and strength of certain toys-Other toys or components of toys with nearly spherical, hemispherical, circular
flared, or dome-shaped ends of toys having a mass less than 0,5 kg and intended for children
under 18 months-Test for shape and size of certain toys) |
- |
500 |
|
- |
| 4.5.1.4 - 5.3(Shape, size and strength of certain toys-Toy fasteners (e.g. nails, bolts, screws, and pegs) with nearly spherical, hemispherical,
or dome-shaped ends intended for children 18 months and over but under 48 months-Test for shape and size of certain toys) |
- |
500 |
|
-- |
| 4.5.2 - 5.4(Shape, size and strength of certain toys-Small balls-Small balls test) |
- |
500 |
|
- |
| 4.5.3 - 5.5(Shape, size and strength of certain toys-Pompoms-Test for pompoms) |
- |
500 |
|
- |
| 4.5.4 - 5.6(Shape, size and strength of certain toys- Pre-school play figures-Test for pre-school play figures) |
- |
500 |
|
- |
| 4.5.5(Shape, size and strength of certain toys-Toy pacifiers-Nipple length) |
- |
500 |
|
- |
| 4.5.6(Shape, size and strength of certain toys-Balloons) |
- |
500 |
|
- |
| 4.5.7(Shape, size and strength of certain toys-Marbles) |
- |
500 |
|
- |
| 4.5.8 - a(Shape, size and strength of certain toys-Hemispheric-shaped toys-No of Opening) |
- |
500 |
|
- |
| 4.5.8 - b(Shape, size and strength of certain toys-Hemispheric-shaped toys-Extension of divider) |
- |
500 |
|
- |
| 4.5.8 - c(Shape, size and strength of certain toys-Hemispheric-shaped toys-No of Opening) |
- |
500 |
|
- |
| 4.5.8 - d(Shape, size and strength of certain toys-Hemispheric-shaped toys) |
- |
500 |
|
- |
| 4.6.3 - 5.8(Edges-Edges on metal toys-Sharp edge test) |
- |
500 |
|
- |
| 4.6.2(Edges-Functional sharp edges) |
- |
500 |
|
- |
| 4.6.4( Edges-Edges on moulded toys) |
- |
500 |
|
- |
| 4.6.5( Edges-Edges on exposed bolts or threaded rod) |
- |
500 |
|
- |
| 4.7.1 - 5.9(Points-Accessible sharp points-sharp-point test) |
- |
500 |
|
- |
| 4.7.2 - a(Points-Functional sharp points) |
- |
500 |
|
- |
| 4.7.2 - b(Points-Functional sharp points) |
- |
500 |
|
- |
| 4.7.3 (Wooden toys) |
- |
500 |
|
- |
| 4.8.1(Projections-General requirments) |
- |
500 |
|
- |
| 4.8.1(Projections-General requirments) |
- |
500 |
|
- |
| 4.9(a) - 5.24.8.2( Metal wires and rods-wires and other metallic components intended to be bent) |
- |
500 |
|
- |
| 4.9(b) - 5.24.8.3( Metal wires and rods-wires likely to be bent) |
- |
500 |
|
- |
| 4.9 - c( Metal wires and rods) |
- |
500 |
|
- |
| 4.9 - c - 5.8( Metal wires and rods-Sharp edge test) |
- |
500 |
|
- |
| 4.9 - c - 5.9( Metal wires and rods-Sharp Point test) |
- |
500 |
|
- |
| 4.9 - c( Metal wires and rods-Minimum dia of spokes) |
- |
500 |
|
- |
| 4.3.1(Material quality) |
- |
500 |
|
- |
| 4.1(Normal use) |
- |
500 |
|
- |
| 4.10(a) - 5.10(Plastic film or plastic bags in packaging and in toys-average thickness) |
- |
500 |
|
- |
| 4.10(a) - 5.10(Plastic film or plastic bags in packaging and in toys- individual thickness) |
- |
500 |
|
- |
| 4.10(a) - 5.10(Plastic film or plastic bags in packaging and in toys- individual thickness) |
- |
500 |
|
- |
| 4.11.2.1(a) - 5.11.2( Cords-Cords in toys intended for children under 18 months-Cords with the potential to tangle-Length of cords and electrical cables) |
- |
500 |
|
- |
| 4.11.2.1(b) - 5.11.3( Cords-Cords in toys intended for children under 18 months-Cords with the potential to tangle-breakaway feature separation test) |
- |
500 |
|
- |
| 4.11.2.1(b) - 5.11.2( Cords-Cords in toys intended for children under 18 months-Cords with the potential to tangle-Length of cords and electrical cables after breakaway feature separation test) |
- |
500 |
|
- |
| 4.11.2.2 - 5.11.2( Cords-Cords in toys intended for children under 18 months--Other cords-free length ) |
- |
500 |
|
- |
| 4.11.3.1(a) - 5.11.2( Cords-Cords in toys intended for children 18 months and over but under 36 months-Cords with the potential to tangle-Length of cords and electrical cables) |
- |
500 |
|
- |
| 4.11.3.1(b) - 5.11.3( Cords-Cords in toys intended for children 18 months and over but under 36 months-Cords with the potential to tangle-breakaway feature separation test) |
- |
500 |
|
- |
| 4.11.3.1(b) - 5.11.2( Cords-Cords in toys intended for children 18 months and over but under 36 months-Cords with the potential to tangle-Length of cords and electrical cables after breakaway feature separation test) |
- |
500 |
|
- |
| 4.11.3.2( Cords-Cords in toys intended for children 18 months and over but under 36 months-Other cords) |
- |
500 |
|
- |
| 4.11.3.3 ( Cords-Cords in toys intended for children 18 months and over but under 36 months-Other cords without a free end
) |
- |
500 |
|
- |
| 4.11.4(a) - 5.11.4.1(Cords-Fixed loops and nooses intended for children under 36 months-Test for fixed loops and nooses-Head probe push test) |
- |
500 |
|
- |
| 4.11.4(a) - 5.11.4.2(Cords-Fixed loops and nooses intended for children under 36 months-Test for fixed loops and nooses-Elastic materials) |
- |
500 |
|
- |
| 4.11.4(b) - 5.11.3(Cords-Fixed loops and nooses intended for children under 36 months-Breakaway feature separation test) |
- |
500 |
|
- |
| 4.11.5 - 5.11.2(Cords-Cords on pull toys-free length) |
- |
500 |
|
- |
| 4.11.6(Cords- Electrical cables) |
- |
500 |
|
- |
| 4.11.7 - 5.11.1(Cords- Diameter of certain cords intended for children under 36 months-cords cross-sectional
dimension) |
- |
500 |
|
- |
| 4.11.8 - 5.11.5(Cords- Self-retracting cords intended for children under 36 months-self-retracting cords) |
- |
500 |
|
- |
| 4.11.9.1(Cords-Toys intended to be strung across a cradle, cot, perambulator or carriage) |
- |
500 |
|
- |
| 4.11.9.2 (Cords-Toys otherwise intended to be attached to a cradle, cot, perambulator or carriage) |
- |
500 |
|
- |
| 4.11.9.2 (Cords-Toys otherwise intended to be attached to a cradle, cot, perambulator or carriage) |
- |
500 |
|
- |
| 4.11.10(Cords-Cords on toy bags) |
- |
500 |
|
- |
| 4.11.11 - 5.11.6( Cords, strings and lines for flying toys- electrical resistance) |
- |
500 |
|
- |
| 4.11.11( Cords, strings and lines for flying toys- ) |
- |
500 |
|
- |
| 4.12.1(a - 1)(Folding mechanisms-Toy pushchairs, perambulators and similar toys) |
- |
500 |
|
- |
| 4.12.1(a - 2)(Folding mechanisms-Toy pushchairs, perambulators and similar toys) |
- |
500 |
|
- |
| 4.12.1(a - 3) - 5.22.2(Folding mechanisms-Toy pushchairs, perambulators and similar toys-toy pushchairs and perambulators) |
- |
500 |
|
- |
| 4.12.1(a - 4)(Folding mechanisms-Toy pushchairs, perambulators and similar toys) |
- |
500 |
|
- |
| 4.12.1(a - 5) - 5.22.2(Folding mechanisms-Toy pushchairs, perambulators and similar toys) |
- |
500 |
|
- |
| 4.12.1(b - 1)(Folding mechanisms-Toy pushchairs, perambulators and similar toys) |
- |
500 |
|
- |
| 4.12.1(b - 2) - 5.22.2(Folding mechanisms-Toy pushchairs, perambulators and similar toys) |
- |
500 |
|
- |
| 4.12.1(b - 3) - 5.22.2(Folding mechanisms-Toy pushchairs, perambulators and similar toys) |
- |
500 |
|
- |
| 4.12.2 (a) - 5.22.3(Folding mechanisms-Other toys with folding mechanisms) |
- |
500 |
|
- |
| 4.12.2 (b)(Folding mechanisms-Other toys with folding mechanisms) |
- |
500 |
|
- |
| 4.12.3(Folding mechanisms-Hinge line clearance) |
- |
500 |
|
- |
| 4.13.1(Holes, clearances and accessibility of mechanisms-Circular holes in rigid materials) |
- |
500 |
|
- |
| 4.13.2 (Holes, clearances and accessibility of mechanisms-Accessible clearances for movable segments) |
- |
500 |
|
- |
| 4.13.3(Holes, clearances and accessibility of mechanisms- Chains or belts in ride-on toys) |
- |
500 |
|
- |
| 4.13.3 - 5.7(Holes, clearances and accessibility of mechanisms- Chains or belts in ride-on toys-accessibility of a part or component) |
- |
500 |
|
- |
| 4.13.3(Holes, clearances and accessibility of mechanisms- Chains or belts in ride-on toys) |
- |
500 |
|
- |
| 4.13.4(Holes, clearances and accessibility of mechanisms-Other driving mechanisms) |
- |
500 |
|
- |
| 4.13.5(Holes, clearances and accessibility of mechanisms-Winding keys) |
- |
500 |
|
- |
| 4.14(a)(Springs) |
- |
500 |
|
- |
| 4.14(b)(Springs) |
- |
500 |
|
- |
| 4.14(c)(Springs) |
- |
500 |
|
- |
| 4.15.1.1 - 5.12.2( Stability and overload requirements-Stability of ride-on toys and seats-Sideways stability, feet available for stabilization) |
- |
500 |
|
- |
| 4.15.1.2 - 5.12.3( Stability and overload requirements-Stability of ride-on toys and seats-Sideways stability, feet unavailable for stabilization) |
- |
500 |
|
- |
| 4.15.1.3 - 5.12.4( Stability and overload requirements-Stability of ride-on toys and seats-Fore and aft stability Test) |
- |
500 |
|
- |
| 4.15.2 - 5.12.5( Stability and overload requirements-Overload requirements for ride-on toys and seats-overload test for ride-on toys and seats) |
- |
500 |
|
- |
| 4.15.2 - 5.24.4( Stability and overload requirements-Overload requirements for ride-on toys and seats-dynamic strength test for wheeled ride-on toys other than toy scooters) |
- |
500 |
|
- |
| 4.15.3 - 5.12.6( Stability and overload requirements-Stability of stationary floor toy-Stability test of stationary floor toys) |
- |
500 |
|
- |
| 4.16.1(Enclosures-Ventilation) |
- |
500 |
|
- |
| 4.16.1(Enclosures-Ventilation-No of openings) |
- |
500 |
|
- |
| 4.16.1(Enclosures-Ventilation-Area of Each openings(If two openings)) |
- |
500 |
|
- |
| 4.16.1(Enclosures-Ventilation-Area of Each openings(If One opening)) |
- |
500 |
|
- |
| 4.16.1(Enclosures-Ventilation-spacing(If One opening)) |
- |
500 |
|
- |
| 4.16.1(Enclosures-Ventilation) |
- |
500 |
|
- |
| 4.16.1(Enclosures-Ventilation) |
- |
500 |
|
- |
| 4.16.2.1(Enclosures-Closures-Lids, doors and similar devices) |
- |
500 |
|
- |
| 4.16.2.1 - 5.13.1(Enclosures-Closures-Lids, doors and similar devices-Test For closures) |
- |
500 |
|
- |
| 4.16.2.2(a)(Enclosures-Closures-Lid support for toy chests and similar toys) |
- |
500 |
|
- |
| 4.16.2.2(a) - 5.13.2.1(Enclosures-Closures-Lid support for toy chests and similar toys-Test For lid support) |
- |
500 |
|
- |
| 4.16.2.2(a) - 5.13.2.2(Enclosures-Closures-Lid support for toy chests and similar toys- After durability test for toy chest lids) |
- |
500 |
|
- |
| 4.16.2.2(a) - 5.13.2.2(Enclosures-Closures-Lid support for toy chests and similar toys-Test For lid support After durability test for toy chest lids) |
- |
500 |
|
- |
| 4.16.2.2(b) - 5.13.2.2(Enclosures-Closures-Lid support for toy chests and similar toys-durability test for toy chest lids) |
- |
500 |
|
- |
| 4.16.2.2(c) - 5.13.2.2 - 4.12.1(a - 1)(Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Toy pushchairs, perambulators and similar toys) |
- |
500 |
|
- |
| 4.16.2.2(c) - 5.13.2.2 - 4.12.1(a - 2)(Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Toy pushchairs, perambulators and similar toys) |
- |
500 |
|
- |
| 4.16.2.2(c) - 5.13.2.2 - 4.12.1(a - 3) - 5.22.2(Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Toy pushchairs, perambulators and similar toys-toy pushchairs and perambulators) |
- |
500 |
|
- |
| 4.16.2.2(c) - 5.13.2.2 - 4.12.1(a - 4)(Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Toy pushchairs, perambulators and similar toys) |
- |
500 |
|
- |
| 4.16.2.2(c) - 5.13.2.2 - 4.12.1(a - 5) - 5.22.2(Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Toy pushchairs, perambulators and similar toys) |
- |
500 |
|
- |
| 4.16.2.2(c) - 5.13.2.2 - 4.12.1(b - 1)(Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Toy pushchairs, perambulators and similar toys) |
- |
500 |
|
- |
| 4.16.2.2(c) - 5.13.2.2 - 4.12.1(b - 2) - 5.22.2(Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Toy pushchairs, perambulators and similar toys) |
- |
500 |
|
- |
| 4.16.2.2(c) - 5.13.2.2 - 4.12.1(b - 3) - 5.22.2(Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Toy pushchairs, perambulators and similar toys) |
- |
500 |
|
- |
| 4.16.2.2(c) - 5.13.2.2 - 4.12.2 (a) - 5.22.3(Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Other toys with folding mechanisms) |
- |
500 |
|
- |
| 4.16.2.2(c) - 5.13.2.2 - 4.12.2 (b)(Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Other toys with folding mechanisms) |
- |
500 |
|
- |
| 4.16.2.2(c) - 5.13.2.2 - 4.12.3(Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Hinge line clearance) |
- |
500 |
|
- |
| 4.16.2.2(d)(Enclosures-Closures-Lid support for toy chests and similar toys) |
- |
500 |
|
- |
| 4.16.3(Enclosures-Toys that enclose the head) |
- |
500 |
|
- |
| 4.16.3(Enclosures-Toys that enclose the head-No of openings) |
- |
500 |
|
- |
| 4.16.3(Enclosures-Toys that enclose the head-Area of Each openings(If two openings)) |
- |
500 |
|
- |
| 4.16.3(Enclosures-Toys that enclose the head-Area of Each openings(If One opening)) |
- |
500 |
|
- |
| 4.16.1(Enclosures-Ventilation-Distance between openings(If two openings)) |
- |
500 |
|
- |
| 4.16.3(Enclosures-Toys that enclose the head-Distance between openings(If two openings)) |
- |
500 |
|
- |
| 4.17 - 5.14(Simulated protective equipment, such as helmets, hats and goggles-Impact test for toys that cover the face) |
- |
500 |
|
- |
| 4.17(Simulated protective equipment, such as helmets, hats and goggles) |
- |
500 |
|
- |
| 4.18.2(a) - 5.36(Projectile toys-Projectiles-tip assessment of rigid projectiles) |
- |
500 |
|
- |
| 4.18.2(b)(Projectile toys-Projectiles) |
- |
500 |
|
- |
| 4.18.2(c)(Projectile toys-Projectiles) |
- |
500 |
|
- |
| 4.18.2(c)(Projectile toys-Projectiles-Radius) |
- |
500 |
|
- |
| 4.18.2(d) - 5.37(Projectile toys-Projectiles-length of suction cup projectiles) |
- |
500 |
|
- |
| 4.18.2(d) - 5.37 - 5.24.5(Projectile toys-Projectiles-length of suction cup projectiles After torque test) |
- |
500 |
|
- |
| 4.18.2(d) - 5.37 - 5.24.6.5(Projectile toys-Projectiles-length of suction cup projectiles After tension test for a projectile with a suction cup) |
- |
500 |
|
- |
| 4.18.2 - e - 5.24.5(Projectile toys-Projectiles-torque test) |
- |
500 |
|
- |
| 4.18.2 - e - 5.24.6.5(Projectile toys-Projectiles-tension test for a projectile with a suction cup) |
- |
500 |
|
- |
| 4.18.3(a) - 5.2(Projectile toys-Projectile toys with stored energy-small parts test) |
- |
500 |
|
- |
| 4.18.3(a) - 5.3 - 5.24(Projectile toys-Projectile toys with stored energy-small parts test after reasonably foreseeable abuse testing) |
- |
500 |
|
- |
| 4.18.3(a) - 5.4(Projectile toys-Projectile toys with stored energy--small parts test after (wall impact test for projectiles) |
- |
500 |
|
- |
| 4.18.3(b)(Projectile toys-Projectile toys with stored energy) |
- |
500 |
|
- |
| 4.18.3(b)(Projectile toys-Projectile toys with stored energy) |
- |
500 |
|
- |
| 4.18.3(b) - 5.15.1.3.3(Projectile toys-Projectile toys with stored energy-determination of kinetic energy per area of contact) |
- |
500 |
|
- |
| 4.18.3(c ) - 5.24.5(Projectile toys-Projectile toys with stored energy-torque test) |
- |
500 |
|
- |
| 4.18.3(c ) - 5.24.6.4(Projectile toys-Projectile toys with stored energy- tension test for protective components) |
- |
500 |
|
- |
| 4.18.3(c )(Projectile toys-Projectile toys with stored energy) |
- |
500 |
|
- |
| 4.18.3(d) - 5.15.2(Projectile toys-Projectile toys with stored energy-Wall impact test for projectiles) |
- |
500 |
|
- |
| 4.18.3(e )(Projectile toys-Projectile toys with stored energystored energy-Discharge mechanism) |
- |
500 |
|
- |
| 4.18.4.1 - 5.20(Projectile toys-Projectile toys without stored energy-Mouth-actuated projectile toys-durability of mouth-actuated toys) |
- |
500 |
|
- |
| 4.18.4.2(a) - 5.15.1.3.3(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart-determination of the kinetic energy per area of contact when the contact area of the dart shall be at least 3 cm^2) |
- |
500 |
|
- |
| 4.18.4.2(b)(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart) |
- |
500 |
|
- |
| 4.18.4.2(b)(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart) |
- |
500 |
|
- |
| 4.18.4.2(b)(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart) |
- |
500 |
|
- |
| 4.18.4.2(c ) - 5.24.5(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart-After torque test) |
- |
500 |
|
- |
| 4.18.4.2(c ) - 5.24.5(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart-After torque test) |
- |
500 |
|
- |
| 4.18.4.2(c ) - 5.24.5(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart-Contact area After torque test) |
- |
500 |
|
- |
| 4.18.4.2(c ) - 5.24.6.4(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart-After tension test for protective
components) |
- |
500 |
|
- |
| 4.18.4.2(c ) - 5.24.6.4(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart-After tension test for protective
components) |
- |
500 |
|
- |
| 4.18.4.2(c ) - 5.24.6.4(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart-Contact area After tension test for protective components) |
- |
500 |
|
- |
| 4.18.4.3 - 5.15.1.3.3(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set)-kinetic energy per area) |
- |
500 |
|
- |
| 4.18.4.3 - 5.15.2(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set)-wall impact test for projectiles) |
- |
500 |
|
- |
| 4.18.4.3(a)(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set) |
- |
500 |
|
- |
| 4.18.4.3(b)(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set) |
- |
500 |
|
- |
| 4.18.4.3(c)(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set) |
- |
500 |
|
- |
| 4.18.4.6 - 5.24.5(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set-After torque test) |
- |
500 |
|
- |
| 4.18.4.6 - 5.24.5(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set-After torque test) |
- |
500 |
|
- |
| 4.18.4.6 - 5.24.5 - 5.15.1.3.3(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set- kinetic energy per area After torque test) |
- |
500 |
|
- |
| 4.18.4.6 - 5.24.6.4(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set-After tension test for protective
components) |
- |
500 |
|
- |
| 4.18.4.6 - 5.24.6.4(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set-After tension test for protective
components) |
- |
500 |
|
- |
| 4.18.4.6 - 5.24.6.4 - 5.15.1.3.3(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set-kinetic energy per area After tension test for protective components) |
- |
500 |
|
- |
| 4.19(Rotors and propellers) |
- |
500 |
|
- |
| 4.2(Aquatic toys) |
- |
500 |
|
- |
| 4.2(Aquatic toys) |
- |
500 |
|
- |
| 4.2(Aquatic toys) |
- |
500 |
|
- |
| 4.2(Aquatic toys) |
- |
500 |
|
- |
| 4.21(a)(Braking) |
- |
500 |
|
- |
| 4.21(a)(Braking-brake performance for mechanically or electrically
powered ride-on toys other than toy bicycles) |
- |
500 |
|
- |
| 4.21(a)(braking) |
- |
500 |
|
- |
| 4.21(b)(braking) |
- |
500 |
|
- |
| 4.22.1(Toy bicycles-Instructions for use) |
- |
500 |
|
- |
| 4.22.2(Toy bicycles-Determination of maximum saddle height) |
- |
500 |
|
- |
| 4.22.2(Toy bicycles-Determination of maximum saddle height) |
- |
500 |
|
- |
| 4.22.3 - 5.16.1(Toy bicycles-Braking requirements-determination of free-wheeling
facility) |
- |
500 |
|
- |
| 4.22.3 (Toy bicycles-Braking requirements- brake lever dimension(d)) |
- |
500 |
|
- |
| 4.22.3 (Toy bicycles-Braking requirements- lever Length(l)) |
- |
500 |
|
- |
| 4.22.3 - 5.16.3(Toy bicycles-Braking requirements- brake performance for toy bicycles) |
- |
500 |
|
- |
| 4.23 - 5.17(Speed limitation of electrically driven ride-on toys-determination of speed of electrically driven ride-on toys) |
- |
500 |
|
- |
| 4.24(a) - 5.18(Toys containing a heat source-determination of temperature increases) |
- |
500 |
|
- |
| 4.24(b) - 5.18(Toys containing a heat source-rise in temperature of handles, knobs and similar parts which are likely to be touched by hand-(Parts made of metals)) |
- |
500 |
|
- |
| 4.24(b) - 5.18(Toys containing a heat source-rise in temperature of handles, knobs and similar parts which are likely to be touched by hand(Parts made of glass or porcelain)) |
- |
500 |
|
- |
| 4.24(b) - 5.18(Toys containing a heat source-rise in temperature of handles, knobs and similar parts which are likely to be touched by hand(Parts made of Plastic or wood )) |
- |
500 |
|
- |
| 4.24(c) - 5.18(Toys containing a heat source- rise in temperature of other accessible parts of the toy(Parts made of metals)) |
- |
500 |
|
- |
| 4.24(c) - 5.18(Toys containing a heat source- rise in temperature of other accessible parts of the toy( Parts made of other materials)) |
- |
500 |
|
- |
| 4.25 - 5.19(Liquid-filled toys-leakage of liquid-filled toys) |
- |
500 |
|
- |
| 4.25(Liquid-filled toys) |
- |
500 |
|
- |
| 4.26(a) - 5.2( Mouth-actuated toys-small parts test) |
- |
500 |
|
- |
| 4.26(b) - 5.24.5 - 5.3( Mouth-actuated toys-small parts test after torque test) |
- |
500 |
|
- |
| 4.26(b) - 5.24.6.1 - 5.4( Mouth-actuated toys-small parts test after tension test, general procedure) |
- |
500 |
|
- |
| 4.26(c ) - 5.20 - 5.2( Mouth-actuated toys-small parts test after durability of mouth-actuated toys) |
- |
500 |
|
- |
| 4.27(Toy roller skates, toy inline skates and toy skateboards) |
- |
500 |
|
- |
| 4.28( Percussion caps specifically designed for use in toys) |
- |
500 |
|
- |
| 4.29(a) - 5.25(Acoustic requirements-determination of sound pressure levels) |
- |
500 |
|
- |
| 4.29(b) - 5.25(Acoustic requirements-determination of sound pressure levels) |
- |
500 |
|
- |
| 4.29(c) - 5.25(Acoustic requirements-determination of sound pressure levels) |
- |
500 |
|
- |
| 4.29(d) - 5.25(Acoustic requirements-determination of sound pressure levels) |
- |
500 |
|
- |
| 4.29(e) - 5.25(Acoustic requirements-determination of sound pressure levels) |
- |
500 |
|
- |
| 4.29(f) - 5.25(Acoustic requirements-determination of sound pressure levels) |
- |
500 |
|
- |
| 4.29(g) - 5.25(Acoustic requirements-determination of sound pressure levels) |
- |
500 |
|
- |
| 4.30.2(Toy scooters-Warnings and instructions for use) |
- |
500 |
|
- |
| 4.30.3 - 5.26 - 5.8(Toy scooters-Strength-After static strength for toy scooters- sharp edge test) |
- |
500 |
|
- |
| 4.30.3 - 5.26 - 5.9(Toy scooters-Strength-static strength for toy scooters-sharp-point test) |
- |
500 |
|
- |
| 4.30.3 - 5.26(Toy scooters-Strength-static strength for toy scooters) |
- |
500 |
|
- |
| 4.30.3 - 5.26(Toy scooters-Strength-static strength for toy scooters) |
- |
500 |
|
- |
| 4.30.3 - 5.27 - 5.8(Toy scooters-Strength-dynamic strength for toy scooters- sharp-edge test) |
- |
500 |
|
- |
| 4.30.3 - 5.27 - 5.9(Toy scooters-Strength-dynamic strength for toy scooters-sharp-point test) |
- |
500 |
|
- |
| 4.30.3 - 5.27(Toy scooters-Strength-dynamic strength for toy scooters) |
- |
500 |
|
- |
| 4.30.3 - 5.27(Toy scooters-Strength-dynamic strength for toy scooters) |
- |
500 |
|
- |
| 4.30.3 - 5.29(Toy scooters-Strength-strength of toy scooter steering tubes) |
- |
500 |
|
- |
| 4.30.3 - 5.29(Toy scooters-Strength-strength of toy scooter steering tubes) |
- |
500 |
|
- |
| 4.30.3 - 5.29(Toy scooters-Strength-strength of toy scooter steering tubes) |
- |
500 |
|
- |
| 4.30.4 - 5.12.2(Toy scooters-Stability-sideways stability test, feet available for stabilization) |
- |
500 |
|
- |
| 4.30.5(a)( Toy scooters-Adjustable and folding steering tubes and handlebars) |
- |
500 |
|
- |
| 4.30.5(a)( Toy scooters-Adjustable and folding steering tubes and handlebars) |
- |
500 |
|
- |
| 4.30.5(b)( Toy scooters-Adjustable and folding steering tubes and handlebars) |
- |
500 |
|
- |
| 4.30.5(c)( Toy scooters-Adjustable and folding steering tubes and handlebars) |
- |
500 |
|
- |
| 4.30.5(d)( Toy scooters-Adjustable and folding steering tubes and handlebars) |
- |
500 |
|
- |
| 4.30.5(e)( Toy scooters-Adjustable and folding steering tubes and handlebars) |
- |
500 |
|
- |
| 4.30.5(f) - 5.30( Toy scooters-Adjustable and folding steering tubes and handlebars-resistance to separation of handlebar) |
- |
500 |
|
- |
| 4.30.6 ( Toy scooters-Braking) |
- |
500 |
|
- |
| 4.30.6 ( Toy scooters-Braking) |
- |
500 |
|
- |
| 4.30.6 - 5.28( Toy scooters-Braking- force required to hold the toy) |
- |
500 |
|
- |
| 4.30.7( Toy scooters-Wheel size(diameter)) |
- |
500 |
|
- |
| 4.30.8(Toy scooters-Projections) |
- |
500 |
|
- |
| 4.30.8(Toy scooters-Projections(rounded handlebar grips or plugs Diameter)) |
- |
500 |
|
- |
| 4.30.8(Toy scooters-Projections(rounded handlebar grips or plugs space from end)) |
- |
500 |
|
- |
| 4.31(Magnets and magnetic components-Magnetic/electrical experimental sets intended for children 8 years and over) |
- |
500 |
|
- |
| 4.31.1 - 5.32(Magnets and magnetic components-Magnetic/electrical experimental sets intended for children 8 years and over-magnetic flux index) |
- |
500 |
|
- |
| 4.31.1 - 5.2(Magnets and magnetic components-Magnetic/electrical experimental sets intended for children 8 years and over-small parts test) |
- |
500 |
|
- |
| 4.31.2(a) - 5.32(Magnets and magnetic components-All other toys with magnets and magnetic components-magnetic flux index) |
- |
500 |
|
- |
| 4.31.2(a) - 5.32(Magnets and magnetic components-All other toys with magnets and magnetic components-small parts test) |
- |
500 |
|
- |
| 4.31.2(c ) - 5.31 - 5.24.2 - 5.24.3 - 5.24.5 - 5.24.6.1 - 5.24.6.2 - 5.33 - 5.31 - 5.32(Magnets and magnetic components-All other toys with magnets and magnetic components-magnetic flux index After Following tests:
-tension test for magnets;
-drop test/tip over test for large and bulky toys;
-torque test;
-tension test, general procedure;
-tension test for seams in soft-filled (stuffed) toys, beanbag-type toys and other similar filled toys, if applicable;
-impact test for magnets;
-compression test;
-tension test for magnets;) |
- |
500 |
|
- |
| 4.31.2(c ) - 5.31 - 5.24.2 - 5.24.3 - 5.24.5 - 5.24.6.1 - 5.24.6.2 - 5.33 - 5.31 - 5.2(Magnets and magnetic components-All other toys with magnets and magnetic components-small parts test After Following tests:
-tension test for magnets;
-drop test/tip over test for large and bulky toys;
-torque test;
-tension test, general procedure;
-tension test for seams in soft-filled (stuffed) toys, beanbag-type toys and other similar filled toys, if applicable;
-impact test for magnets;
-compression test;
-tension test for magnets;) |
- |
500 |
|
- |
| 4.32 - 5.38.2( Yo-yo balls - length (lo) of the yo-yo ball tether) |
- |
500 |
|
- |
| 4.32 - 5.38.1( Yo-yo balls - The ratio of the mass m (in grams) to the elastic constant k of the yo-yo ball tether(m/k)) |
- |
500 |
|
- |
| 4.33 - 5.11.3(Straps intended to be worn fully or partially around the neck-breakaway feature separation test) |
- |
500 |
|
- |
| 4.34(Sledges and toboggans with cords for pulling) |
- |
500 |
|
- |
| 4.35.3 - 5.39(Jaw entrapment in handles and steering wheels-jaw entrapment test) |
- |
500 |
|
- |
| 9873 (Part - 2) 4.5 - 5.5(Soft-filled toys-Test for soft-filled toys
) |
- |
500 |
|
- |
| 9873 (Part - 2) 4.5 - 5.5(Soft-filled toys-rate of spread of flame ) |
- |
500 |
|
- |
| 9873 (Part - 2) 4.4(Toys intended to be entered by a child-rate of spread of flame-Test relating to flowing elements of toys to be worn on the head (except those
covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child
) |
- |
500 |
|
- |
| 9873 (Part - 2) 4.4 - 5.4(Toys intended to be entered by a child-rate of spread of flame-Test relating to flowing elements of toys to be worn on the head (except those
covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child
) |
- |
500 |
|
- |
| 9873 (Part - 2) 4.4 - 5.4(Toys intended to be entered by a child-rate of spread of flame-Test relating to flowing elements of toys to be worn on the head (except those
covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child) |
- |
500 |
|
- |
| 9873 (Part - 2) 4.4 - 5.4(Toys intended to be entered by a child-rate of spread of flame) |
- |
500 |
|
- |
| 9873 (Part - 2) 4.3(Toys to be worn on the head-Toy disguise costumes and toys intended to be worn by a child in play) |
- |
500 |
|
- |
| 9873 (Part - 2) 4.3 - 5.4(Toys to be worn on the head-Toy disguise costumes and toys intended to be worn by a child in play-Test relating to flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child) |
- |
500 |
|
- |
| 9873 (Part - 2) 4.3 - 5.4(Toys to be worn on the head-Toy disguise costumes and toys intended to be worn by a child in play-rate of spread of flame) |
- |
500 |
|
- |
| 9873 (Part - 1) 4.2.5 - 5.4(Toys to be worn on the head-Flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks)-Test relating to flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child
) |
- |
500 |
|
- |
| 9873 (Part - 1) 4.2.5 - 5.4(Toys to be worn on the head-Flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks)-rate of spread of flame) |
- |
500 |
|
- |
| 9873 (Part - 1) 4.2.4 - 5.3(Toys to be worn on the head-Full or partial moulded head masks-maximum distance between the upper edge of the burnt area and the point of application of the test flame) |
- |
500 |
|
- |
| 9873 (Part - 1) 4.2.4 - 5.3(Toys to be worn on the head-Full or partial moulded head masks-Duration of the flame after the removal of the test flame) |
- |
500 |
|
- |
| 9873 (Part - 1) 4.2.3 - 5.3(Toys to be worn on the head-Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude less than 50 mm and more than 5 mm from the surface of the toy- maximum distance between the upper edge of the burnt area and the point of application of the test flame) |
- |
500 |
|
- |
| 9873 (Part - 1) 4.2.2(b) - 5.3(Toys to be worn on the head-Test relating to Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude 50 mm or more from the surface of the toy- if ignition occurs, the maximum burnt length of hair, pile, or material that behaves in a similar manner when the initial length was less than 150 mm) |
- |
500 |
|
- |
| 9873 (Part - 1) 4.2.2(a) - 5.3(Toys to be worn on the head-Test relating to Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude 50 mm or more from the surface of the toy- if ignition occurs, the maximum burnt length of hair, pile, or material that behaves in a similar manner when the initial length was 150 mm or more) |
- |
500 |
|
- |
| 9873 (Part - 1) 4.2.2 - 5.2(Toys to be worn on the head-Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude 50 mm or more from the surface of the toy-Duration of the flame after the removal of the test flame) |
- |
500 |
|
- |
| 9873 (Part - 9) 3(Vinyl in any part of the toy or childcare article that can be placed in mouth of a child under 4 years of age - a) Di-iso-Nonyl Phthalate (DINP), b) Di-iso-Decyl Phthalate (DIDP), c) Di-n-Octyl Phthalate (DNOP) - IS 9873 Part 6) |
- |
500 |
|
- |
| 9873 (Part - 9) 3(Vinyl in toys or childcare articles - a) Bis-(2-ethlyhexyl) Phthalates (DEHP), b) Di-Butyl phthalate (DBP), c) Benzyl butyl Phthalate (BBP) - IS 9873 Part 6) |
- |
500 |
|
- |
| 9873 (Part - 9) 3(Vinyl in toys or childcare articles - a) Bis-(2-ethlyhexyl) Phthalates (DEHP), b) Di-Butyl phthalate (DBP), c) Benzyl butyl Phthalate (BBP) - IS 9873 Part 6) |
- |
500 |
|
- |
| 9873 (Part - 3) 4.1 - Table 1(Selenium (Se) - Cl 7,8,9 ) |
- |
500 |
|
- |
| 9873 (Part - 3) 4.1 - Table 1(Mercury (Hg) - Cl 7,8,9 ) |
- |
500 |
|
- |
| 9873 (Part - 3) 4.1 - Table 1(Lead (Pb) - Cl 7,8,9 ) |
- |
500 |
|
- |
| 9873 (Part - 3) 4.1 - Table 1(Chromium (Cr) - Cl 7,8,9 ) |
- |
500 |
|
- |
| 9873 (Part - 3) 4.1 - Table 1(Cadmium (Cd) - Cl 7,8,9) |
- |
500 |
|
- |
| 9873 (Part - 3) 4.1 - Table 1(Barium (Ba) - Cl 7,8,9 ) |
- |
500 |
|
- |
| 9873 (Part - 3) 4.1 - Table 1(Arsenic (As) - Cl 7,8,9 ) |
- |
500 |
|
- |
| 9873 (Part - 3) 4.1 - Table 1(Antimony (Sb) - Cl 7,8,9) |
- |
500 |
|
- |
|
- |
-
- |
| 9878 |
Delta Testing and Research Laboratories Private Limited (C5)
| 9179506
| IS 383 (2016) |
Coarse and Fine Aggregate for Concrete - Specification (Third Revision) |
All Grade / Type / Size / Designation |
12000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 5.4.1 (a)(mechanical properties- Aggregate Crushing Value/Ten Percent Fines Value) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.4.1 (b)(mechanical properties- Aggregate Crushing Value/Ten Percent Fines Value) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.4.2(a)( Aggregates Impact Value) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.4.2(b)( Aggregates Impact Value) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.4.3(a)( Aggregate Abrasion Value) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.4.3(b)( Aggregate Abrasion Value) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.1-Table 7(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Nominal Size of aggregate) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.1-Table 7(i)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 80 mm sieve ) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.1-Table 7(ii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 63 mm sieve ) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.1-Table 7(iii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 40 mm sieve ) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.1-Table 7(iv)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 20 mm sieve ) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.1-Table 7(v)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 16 mm sieve ) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.1-Table 7(vi)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 12.5 mm sieve ) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.1-Table 7(vii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 10 mm sieve ) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.1-Table 7(viii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 4.75 mm sieve ) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.1-Table 7(ix)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 2.36 mm sieve ) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.1.1-Table 8(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Class) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.1.1-Table 8(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Size) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.1.1-Table 8(i)(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Percentage Passing through 160 mm Sieve) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.1.1-Table 8(i)(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Percentage Passing through 80 mm Sieve) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.1.1-Table 8(ii)(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Percentage Passing through 80 mm Sieve) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.1.1-Table 8(ii)(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Percentage Passing through 40 mm Sieve) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.1.1-Table 8(iii)(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Percentage Passing through 40 mm Sieve) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.1.1-Table 8(iii)(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Percentage Passing through 20 mm Sieve) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.1.1-Table 8(iv)(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Percentage Passing through 20 mm Sieve) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.1.1-Table 8(iv)(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Percentage Passing through 4.75 mm Sieve) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.1.1-Table 8(iv)(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Percentage Passing through 2.36 mm Sieve) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2-Table 7(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Nominal Size of aggregate) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2-Table 7(i)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 80 mm sieve) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2-Table 7(ii)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 63 mm sieve) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2-Table 7(iii)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 40 mm sieve) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2-Table 7(iv)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 20 mm sieve) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2-Table 7(v)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 16 mm sieve) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2-Table 7(vi)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 12.5 mm sieve) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2-Table 7(vii)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 10 mm sieve) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2-Table 7(viii)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 4.75 mm sieve) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2-Table 7(ix)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 2.36 mm sieve) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.3-Table 9(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Grading Zone) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.3-Table 9(i)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 10mm Sieve ) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.3-Table 9(ii)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 4.75mm Sieve ) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.3-Table 9(iii)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 2.36mm Sieve ) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.3-Table 9(iv)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 1.18mm Sieve ) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.3-Table 9(v)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 600µm Sieve ) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.3-Table 9(vi)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 300µm Sieve ) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.3-Table 9(vii)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 150µm Sieve ) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.4-Table 10(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Nominal Size ) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.4-Table 10(i)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 80mm Sieve ) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.4-Table 10(ii)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 40mm Sieve ) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.4-Table 10(iii)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 20mm Sieve ) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.4-Table 10(iv)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 4.75mm Sieve ) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.4-Table 10(v)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 600µm Sieve ) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.4-Table 10(vi)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 150µm Sieve ) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.7-Table-3-(v) IS: 2386 (P-3)(specific gravity(fine aggregate)) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.7-Table-3-(Iv) IS: 2386 (P-3)(Water absorption (fine aggregate)) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.7-Table-3-(III) IS:14959 (P-2)(Water soluble chloride content (fine aggregate)) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.7-Table-3-(II) IS:4032(Total sulphate content (fine aggregate)) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.6-IS: 2386 (P-7)(Alkali Aggregate Reaction (fine aggregate)) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.5-IS: 2386 (P-5)(Soundness (fine aggregate)) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.2- TABLE-2- (Note-3) IS-2386 (P-2)(Mica content (fine aggregate)) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.2- TABLE-2- (Note-4) IS-2386 (P-2)(Effect of organic impurities on strength of mortar (fine aggregate)) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.2- TABLE-2- (Note-4) IS-2386 (P-2)(Effect of organic impurities on strength of mortar (fine aggregate)) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.2- TABLE-2- (Note-4) IS-2386 (P-2)(Organic impurities (fine aggregate)) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.2- TABLE-2- (vi) IS-2386 (P-2)(Total deleterious material (fine aggregate)) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.2- TABLE-2- (iii) IS-2386 (P-1)(Material fine aggregater than 75 micron (fine aggregate)) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.2- TABLE-2- (ii) IS-2386 (P-2)(Clay lumps (fine aggregate )) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.2- TABLE-2- (i) IS-2386 (P-2)(Coal and Lignite (fine aggregate )) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.7-Table-3-(v) IS: 2386 (P-3)(specific gravity(coarse aggregate)) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.7-Table-3-(Iv) IS: 2386 (P-3)(Water absorption (coarse aggregate)) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.7-Table-3-(III) BN EN: 1744(Water soluble chloride content (coarse aggregate)) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.7-Table-3-(II) BN EN: 1744(Total sulphate content (coarse aggregate)) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.6-IS: 2386 (P-7)(Alkali Aggregate Reaction (coarse aggregate)) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.5-IS: 2386 (P-5)(Soundness (coarse aggregate)) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.3-IS: 2386 (P-1)(Combined elongation & flakiness index (coarse aggregate)) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.2- TABLE-2- (vi) IS-2386 (P-2)(Total deleterious material (coarse aggregate)) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.2- TABLE-2- (iv) IS-2386 (P-2)(Soft fragments (coarse aggregate)) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.2- TABLE-2- (iii) IS-2386 (P-1)(Material fine aggregater than 75 micron (coarse aggregate)) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.2- TABLE-2- (ii) IS-2386 (P-2)(Clay lumps (coarse aggregate )) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.2- TABLE-2- (i) IS-2386 (P-2)(Coal and Lignite (coarse aggregate )) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.5(Soundness By Magnesium Sulphate) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.2(Moisture Content) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.2(Bulking Of Fine Aggregate) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.2(Bulk Density loose) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.2(Bulk Density Rodded) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Clause 5.7- Table 3 (i) (TotalAlkali content as Na2O equivalent ) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Clause 5.6(Nature of Aggregate) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.5(Soundness By Magnesium Sulphate) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.2(Moisture Content) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.2(Bulk Density loose) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.2(Bulk Density Rodded) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.3(Elongation Index) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.3(Flakiness Index) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.6(Alkali Agregate Reaction ) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.7 table 3(WaterAbsorption) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.7 table 3(Specific Gravity) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.3(Flakiness & Elongation) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.5 Na2so4/5.5.1 Maso4/5.5.1 (Soundness) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.7 table 4 (Calcium oxide) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.5 Na2so4/5.5.1 Maso4/5.5.1 (Soundness) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.2 (5.2.2, 5.2.1, 5.2.3, shale table-2 ) (Deleterious material (Clay lumps, coal & lignite, material finer than 75 micron IS sieve, Soft fragments,shale)) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 3.2.2
Table 3 ii)
IS 1963(Basicity as CaO/SiO2) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Clause 5.6(Dissolved Silica) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Clause 5.6(Reduction in Alkalinity) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Clause 5.1(General) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Clause 5.1(General) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Table 4 Cl. 5.7 (ii)(Total Sulphur as S) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Table 4 Cl. 5.7 (iii)(Total iron as FeO) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Table 5 Cl. 5.7 (i)(Calcium oxide as CaO,) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Table 5 Cl. 5.7 (ii)(Magnesium oxide as MgO) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Table 5 Cl. 5.7 (iii)(Total iron as FeO) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Table 5 Cl. 5.7 (iv)(Basicity as CaO/SiO2) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Table 6 Cl. 5.7 (i)(Calcium oxide as CaO) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Table 6 Cl. 5.7 (ii)(Total sulphur as S) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Table 6 Cl. 5.7 (iii)(Total iron as FeO) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Table 6 Cl. 5.7 (iv)() |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Table 6 Cl. 5.7 (iv)() |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
|
21 Aug, 2027 |
-
- |
| 9879 |
Testtex India Laboratories Private Limited, Noida
| 8138306
| IS 3976 (2018) |
Safety Rubber Canvas Boots for Miners †Specification ( Sixth Revision ) |
Safety Boots for miners |
62100 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 5.1(Design) |
- |
300 |
|
- |
| Cl.5.2.1 Upper
Cl.5.2.1.1
IS 3400(Part 5)( Composite upper material shall comply with consolidation test as per 5.10.(IS 3400 (Part 5). There shall be no separation at a load
of 1.5 kg.)) |
- |
400 |
|
- |
| Cl.5.2.1 Upper
Cl.5.2.1.1
IS 3400(Part 5)( Composite upper material shall comply with consolidation test as per 5.10.(IS 3400 (Part 5). There shall be no separation at a load
of 1.5 kg.)) |
- |
400 |
|
- |
| Cl.5.2.1.2( Composite upper material shall comply with
tear strength as per 5.4.3 of IS 15298 (Part 2).) |
- |
500 |
|
- |
| Cl.5.2.1.3 ,
Cl.6.5 of IS 15298 (Part 1).( Composite upper material shall develop no cracks before 150 000 cycles when tested in accordance
with 6.5 of IS 15298 (Part 1).) |
- |
1000 |
|
- |
| Cl.5.2.1.4 ( Type 2 footwear, the composite upper
material shall comply with requirements of water coefficient as prescribed
in 5.4.6 of IS 15298 (Part 2).) |
- |
1000 |
|
- |
| Cl.5.2.1.5( Inner layer of upper shall meet requirement of abrasion resistance as prescribed in 5.5.2 of IS 15298 (Part 2).) |
- |
1000 |
|
- |
| Cl.5.2.2 Compact Insole/Compact Insocks/Counter
Stiffener Lining(Textile material shall be used as lining material for
compact insole/compact insocks / counter stiffener. It
shall meet the requirement of tear strength as prescribed
in 5.6.1 of IS 15298 (Part 2).) |
- |
500 |
|
- |
| Cl.5.2.2.1 Abrasion resistance of compact insole/insocks/
counter stiffener(
When textiles used as lining for all the above are tested
in accordance with 6.12 of IS 15298 (Part 1), the lining
shall not develop any holes before the following number
of cycles has been performed:) |
- |
1000 |
|
- |
| Cl.5.2.3 Coated Binding Material
IS 1954(
Coated binding materials shall conform to the
requirements given in col 3 of Table 1 when tested
according to the methods prescribed in col 4 of Table 1.
i)Width in mm,
) |
- |
300 |
|
- |
| Cl.5.2.3 Coated Binding Material
Annex C(ii) Breaking load in N, Min (50 cm grip length test specimen) ) |
- |
500 |
|
- |
| Cl.5.2.3.1 In case of cotton black binding materia( the same shall be free from sulphur dyes when tested in
accordance with Annex B.) |
- |
1000 |
|
- |
| 5.2.4(Reinforcing Material) |
- |
300 |
|
- |
| Cl.5.2.5 Compact Sole Heel
Cl. 5.2.5.1
(The compact sole heel shall be made out
of polymeric/rubber components and the typical design
recommendation (not mandatory) of compact sole heel
is as shown in Fig. 3. Sectional view of Type 1/Type 2
)
toe position is given in Fig. 4.) |
- |
0 |
|
- |
| Cl.5.2.5 Compact Sole Heel
Cl.5.2.5.1 IS 3400 (Part 2)(requirements prescribed in col 3 of Table 2 when tested
as per corresponding test methods prescribed in col 4
of Table 2.
i)i) Hardness (IRHD) |
- |
500 |
|
- |
| Cl.5.2.5 Compact Sole Heel
5.2.5.1 IS 3400 (Part 4)(ii)*Change in hardness after
accelerated ageing at 100 ± 2
°C for 24 h
) |
- |
1500 |
|
- |
| Cl.5.2.5.3 Ageing for whole footwear(When rubber is used for manufacturing boots or when
the outer sole heel is made of bi-polymer, the finished
boots shall be aged at 100 ± 2°C for 24 h. On completion of test, all rubber components shall not
develop any sign of tackiness or brittleness.) |
- |
1000 |
|
Thickness of Component |
| Cl.5.2.5.4 Thickness of compact sole hee(Thickness of compact sole heel of the boots shall
comply with the thickness and material requirements
prescribed in Table 3.) |
- |
1000 |
|
Abrasion Resistance |
| Cl.5.2.5.4 Thickness of compact sole hee(of black cotton thread, the same shall be free from
sulphur dyes when tested in accordance with
Annex B.) |
- |
1000 |
|
Flexing Resistance |
| Cl.5.2.5.4 Thickness of compact sole hee(Thickness of compact sole heel of the boots shall
comply with the thickness and material requirements
prescribed in Table 3.) |
- |
500 |
|
Tear Strength |
| Cl.5.2.5.4 Thickness of compact sole hee(of black cotton thread, the same shall be free from
sulphur dyes when tested in accordance with
Annex B.) |
- |
500 |
|
Resistance to Hot contact |
| Cl.5.2.5.4 Thickness of compact sole hee(of black cotton thread, the same shall be free from
sulphur dyes when tested in accordance with
Annex B.) |
- |
1500 |
|
Hydrolysis |
| Cl.5.2.5.3 Ageing for whole footwear(When rubber is used for manufacturing boots or when
the outer sole heel is made of bi-polymer, the finished
boots shall be aged at 100 ± 2°C for 24 h. On completion of test, all rubber components shall not
develop any sign of tackiness or brittleness.) |
- |
1500 |
|
Ageing of Whole Footwear |
| Cl.5.2.6 Thread for Upper Closing(
The length (m/kg) and construction of sewing thread
shall conform to requirements as prescribed in
Table 4.) |
- |
400 |
|
- |
| Cl.5.2.6 Thread for Upper Closing(
The length (m/kg) and construction of sewing thread
shall conform to requirements as prescribed in
Table 4.) |
- |
1000 |
|
Detection of Sulphur Dye |
| Cl.5.2.7 Safety Toe Cap(Safety toe cap as per 3.6 shall be fitted into the footwear and must not come out while in use.) |
- |
500 |
|
Safety Toe Cap - Dimensions |
| Cl.5.2.7 Safety Toe Cap(Safety toe cap as per 3.6 shall be fitted into the footwear and must not come out while in use.) |
- |
1500 |
|
Safety Toe Cap - Performance Test |
| Cl.5.2.7 Safety Toe Cap(Safety toe cap as per 3.6 shall be fitted into the footwear and must not come out while in use.) |
- |
1000 |
|
Safety Toe Cap - Finish (Rs. 500)
Safety Toe Cap - Rust prevention (Rs. 500) |
| Cl.5.2.8.1( The boots shall be provided with laces having minimum length of 115 cm for Type 1 and minimum
100 cm for Type 2.) |
- |
300 |
|
5.2.9.1 |
| Cl.5.2.8.2 (Minimum breaking load of 60 kg is to be
achieved when tested between 18 cm grip length in
accordance with Annex C.) |
- |
500 |
|
5.2.9.2 |
| Cl.5.2.8.3( In case of cotton lace of black colour, the same
shall be free from sulphur dyes when tested in
accordance with Annex B. Two ends of the laces shall
be provided with plastic tips.) |
- |
1000 |
|
5.2.9.3 |
| Cl.5.2.9 Eyelets(
Aluminum eyelets of external collar diameter not less
than 10 mm and wall thickness of 0.30 to 0.35 mm
shall be used.) |
- |
500 |
|
5.2.10 |
| CL.5.2.10 Counter Stiffener(
A counter stiffener, made out of textile reinforced withpolymer/rubber including (thermoplastic) having
thickness not less than 1.5 mm is to be stitched at inside
of upper so as to fortify the back of the footwear at
joints of quarter.) |
- |
300 |
|
5.2.11 |
| 5.3, 5.3.1,5.3.3,5.3.4(Construction) |
- |
300 |
|
5.3.1 Construction - Stitch/dm |
| Cl.5.3.2 (The tongue shall be made out of composite upper
material and shall be half bellow type for Type 2 and
full bellow type for Type 1.) |
- |
0 |
|
- |
| Cl.5.3.5 Outer toe cap( shall be provided which is made
of polymer/rubber and it shall be strongly adhered such
that it shall not open up or come out while in use. Toe
of the boot shall be reinforced with safety toe cap) |
- |
0 |
|
- |
| Cl.5.3.6( A designed foxing of width of minimum 25 mm
and of thickness of minimum 2 mm is to be provided.
The foxing shall not extend the edges of the outer
sole.) |
- |
600 |
|
- |
| Cl.5.3.7( Two pairs of detachable insocks are to be
provided. The insocks shall be compact in nature having
thickness not less than 2 mm.) |
- |
300 |
|
- |
| Cl.5.4 Finish(
In appearance, general workmanship and in all other
respects with regard to finish and get up of the footwear,
the footwear shall be matching to the approved sample
of the purchaser.) |
- |
300 |
|
- |
| Cl.5.5 Mass(The mass of one pair of finished footwear of size 8
shall not exceed 1 500 g for Type 1 and 1 400 g for
Type 2 with an increase or decrease of 100 g for each
bigger or smaller size, respectively.) |
- |
300 |
|
- |
| Cl.5.6( Height of Upper
Height of upper of the boots shall conform to column 5
(Design C) and column 4 (Design B) of 5.2.2, Table 4
of IS 15298 (Part 2) for Type 1 and Type 2, respectively
when measured as per 6.2 of IS 15298 (Part 1) on the
inside of the back of the footwear and from seat of the
insole to top edge of the upper.) |
- |
300 |
|
- |
| Cl.5.7 Performance Test(When safety footwear is tested in accordance with the
method described in 5.4 of IS 15298 (Part 1), at an
impact energy of (200 ± 4) J, the clearance under the
toecap at the moment of impact shall be in accordance
with Table 5. In addition, the toecap shall not develop
any cracks which go through the material, that is,
through which light can be seen.) |
- |
2000 |
|
- |
| Cl.5.8 Upper/Outsole Bond Strength(When the footwear is tested in accordance with the
method prescribed in 5.2 of IS 15298 (Part 1), the bond
strength shall not be less than 4.0 N/mm, unless there
is tearing of the sole in which case the bond strength
shall not be less than 3.0 N/mm.) |
- |
1000 |
|
- |
| Cl.5.9 Sole Interlayer Bond Strength for Bi-polymer(
and Bi-density Sole
When tested in accordance with 5.2 of IS 15298 (Part 1),
the bond strength between the outer or cleated layer
and the adjacent layer shall not be less than 4.0 N/mm
unless there is tearing of any part of the sole, in which
case the bond strength shall not be less than 3.0 N/mm.) |
- |
1000 |
|
- |
| Cl.5.10 Consolidation Test(
Representative sample of width 25 ± 0.5 mm are cut
out from the quarter of the upper along the length of
boot. The plies are separated by breaking the bond.
Carry out the test on two specimens in accordance with
IS 3400 (Part 5). Th) |
- |
1000 |
|
- |
| Cl.5.11 Compression Resistance(
5.11.1 When safety boots are tested in accordance
with 5.5 of IS 15298 (Part 1), the clearance under the
toe cap at a compression load of 15 kN ± 0.1 kN shall
be in accordance with Table 5.) |
- |
1000 |
|
- |
| Cl.5.13 Energy Absorption Test(When footwear is tested in accordance with the method
prescribed in 5.14 of IS 15298 (Part 1), the energy
absorption of the seat region shall not be less than 20 J.) |
- |
1500 |
|
- |
| 7.1(Resistance to fuel) |
- |
1000 |
|
- |
| 8(CHEMICAL REQUIREMENTS) |
- |
26500 |
|
- |
| 9, 9.1(BIS CERTIFICATION MARKING) |
- |
0 |
|
- |
| 9, 9.1(BIS CERTIFICATION MARKING) |
- |
0 |
|
- |
| 10(Marking) |
- |
0 |
|
- |
| 10(Marking) |
- |
0 |
|
- |
| Cl. 8 (IS 17011, Table-1 (i))(Allergenic and carcinogenic disperse dyes) |
- |
0 |
|
Clause Repeated |
| 11(Packing) |
- |
0 |
|
Clause Repeated |
| 11(PACKING) |
- |
0 |
|
Clause Repeated |
| Cl.6.3 Tear Strength of Compact Outsole(
When outsoles are tested in accordance to 8.2 of
IS 15298 (Part 1), the tear strength shall be not less
than 8 kN/m for material having density higher
than 0.9/cm³ and when density of material is less than
or equal to 0.9 g/cm³, tear strength shall not be less
than 5 kN/m.) |
- |
0 |
|
Clause Amended |
| Cl.5.13 Energy Absorption Test(When footwear is tested in accordance with the method
prescribed in 5.14 of IS 15298 (Part 1), the energy
absorption of the seat region shall not be less than 20 J.) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.3 Coated Binding Material
IS 1954(
Coated binding materials shall conform to the
requirements given in col 3 of Table 1 when tested
according to the methods prescribed in col 4 of Table 1.
i)Width in mm,
) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.3 Coated Binding Material
Annex C(ii) Breaking load in N, Min (50 cm grip length test specimen) ) |
- |
0 |
|
Clause Repeated |
| Cl.5.13 Energy Absorption Test(When footwear is tested in accordance with the method
prescribed in 5.14 of IS 15298 (Part 1), the energy
absorption of the seat region shall not be less than 20 J.) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.3 Coated Binding Material
Annex C(ii) Breaking load in N, Min (50 cm grip length test specimen) ) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.1.4 ( Type 2 footwear, the composite upper
material shall comply with requirements of water
vapour permeability as prescribed
in 5.4.6 of IS 15298 (Part 2).) |
- |
0 |
|
Clause Amended |
| CL.5.2.10 Counter Stiffener(
A counter stiffener, made out of textile reinforced withpolymer/rubber including (thermoplastic) having
thickness not less than 1.5 mm is to be stitched at inside
of upper so as to fortify the back of the footwear at
joints of quarter.) |
- |
0 |
|
Clause Amended |
| Cl.5.1.1 Fittings(Fittings of the footwear shall be in conformity to Table 9
of IS 1638 (measurement of men’s lasts) and Table 8
of IS 1638 (measurement of women’s lasts).) |
- |
300 |
|
- |
| Cl.5.2.5.3 Ageing for whole footwear(When rubber is used for manufacturing boots or when
the outer sole heel is made of bi-polymer, the finished
boots shall be aged at 100 ± 2°C for 24 h. On completion of test, all rubber components shall not
develop any sign of tackiness or brittleness.) |
- |
0 |
|
- |
| Cl.5.12 Internal Length of Toe Cap(
For safety boots, internal length of the toe cap shall
meet the specification given in Table 5 of IS 15298
(Part 2) when tested as per 5.3 of IS 15298 (Part 1).) |
- |
0 |
|
Clause Amended |
| Cl.6.1 Abrasion Resistance of Compact Outsole(
When outsole is tested in accordance with 8.3 of
IS 15298 (Part 1), the relative volume loss shall not
be greater than 250 mm³ for materials having density
0.9 g/cm³ or less, and not greater than 150 mm³ for
materials with density greater than 0.9 g/cm³.) |
- |
0 |
|
Clause Amended |
| Cl.6.2 Flexing Resistance of Compact Outsole(
When outsole is tested in accordance with 8.4 of
IS 15298 (Part 1), the cut growth shall not be greater
than 4 mm before 30 000 cycles.) |
- |
0 |
|
Clause Amended |
| Cl.6.4 Resistance to Hot Contact( — Sole Heel
When sole heel is tested in accordance with 8.7 of IS 15298 (Part 1), the material shall not melt/deform
and shall not develop any cracks when bent around the
mandrel.) |
- |
0 |
|
Clause Amended |
| Cl.6.5 Hydrolysis(
When bottom sole or other components are made out
of polyurethane, the same shall be tested in accordance
with 8.5 of IS 15298 (Part 1) and the same shall comply
with 5.8.5 of IS 15298 (Part 2).) |
- |
0 |
|
Clause Amended |
| Cl.5.2.5 Compact Sole Heel
Cl.5.2.5.1 IS 3400 (Part 2)(requirements prescribed in col 3 of Table 2 when tested
as per corresponding test methods prescribed in col 4
of Table 2.
i)i) Hardness (IRHD) |
- |
0 |
|
Clause Amended |
| Cl.6.3 Tear Strength of Compact Outsole(
When outsoles are tested in accordance to 8.2 of
IS 15298 (Part 1), the tear strength shall be not less
than 8 kN/m for material having density higher
than 0.9/cm³ and when density of material is less than
or equal to 0.9 g/cm³, tear strength shall not be less
than 5 kN/m.) |
- |
0 |
|
Clause Amended |
| Cl.5.2.1.4 ( Type 2 footwear, the composite upper
material shall comply with requirements of water coefficient as prescribed
in 5.4.6 of IS 15298 (Part 2).) |
- |
0 |
|
Claus Repeated |
| Cl.5.2.1.4 ( Type 2 footwear, the composite upper
material shall comply with requirements of water
vapour permeability as prescribed
in 5.4.6 of IS 15298 (Part 2).) |
- |
0 |
|
Clause Amended |
| Cl.5.1.1 Fittings(Fittings of the footwear shall be in conformity to Table 9
of IS 1638 (measurement of men’s lasts) and Table 8
of IS 1638 (measurement of women’s lasts).) |
- |
0 |
|
Claus Repeated |
| Cl.5.2.1.2( Composite upper material shall comply with
tear strength as per 5.4.3 of IS 15298 (Part 2).) |
- |
0 |
|
Clause Amended |
| Cl.5.2.1.3 ,
Cl.6.5 of IS 15298 (Part 1).( Composite upper material shall develop no cracks before 150 000 cycles when tested in accordance
with 6.5 of IS 15298 (Part 1).) |
- |
0 |
|
Clause Amended |
| Cl.5.2.1.5( Inner layer of upper shall meet requirement of abrasion resistance as prescribed in 5.5.2 of IS 15298 (Part 2).) |
- |
0 |
|
Clause Amended |
| Cl.5.2.2 Compact Insole/Compact Insocks/Counter
Stiffener Lining(Textile material shall be used as lining material for
compact insole/compact insocks / counter stiffener. It
shall meet the requirement of tear strength as prescribed
in 5.6.1 of IS 15298 (Part 2).) |
- |
0 |
|
Clause Amended |
| Cl.5.2.2.1 Abrasion resistance of compact insole/insocks/
counter stiffener(
When textiles used as lining for all the above are tested
in accordance with 6.12 of IS 15298 (Part 1), the lining
shall not develop any holes before the following number
of cycles has been performed:) |
- |
0 |
|
Clause Amended |
| Cl.5.2.3.1 In case of cotton black binding materia( the same shall be free from sulphur dyes when tested in
accordance with Annex B.) |
- |
0 |
|
Clause Amended |
| Cl.5.2.5 Compact Sole Heel
Cl. 5.2.5.1
(The compact sole heel shall be made out
of polymeric/rubber components and the typical design
recommendation (not mandatory) of compact sole heel
is as shown in Fig. 3. Sectional view of Type 1/Type 2
)
toe position is given in Fig. 4.) |
- |
0 |
|
Clause Amended |
| Cl.5.2.5 Compact Sole Heel
5.2.5.1 IS 3400 (Part 4)(ii)*Change in hardness after
accelerated ageing at 100 ± 2
°C for 24 h
) |
- |
0 |
|
Clause Amended |
| Cl.5.2.8.1( The boots shall be provided with laces having minimum length of 115 cm for Type 1 and minimum
100 cm for Type 2.) |
- |
0 |
|
Clause Amended |
| Cl.5.2.8.2 (Minimum breaking load of 60 kg is to be
achieved when tested between 18 cm grip length in
accordance with Annex C.) |
- |
0 |
|
Clause Amended |
| Cl.5.2.8.3( In case of cotton lace of black colour, the same
shall be free from sulphur dyes when tested in
accordance with Annex B. Two ends of the laces shall
be provided with plastic tips.) |
- |
0 |
|
Clause Amended |
| Cl.5.2.9 Eyelets(
Aluminum eyelets of external collar diameter not less
than 10 mm and wall thickness of 0.30 to 0.35 mm
shall be used.) |
- |
0 |
|
Clause Repeated |
| Cl.5.3.2 (The tongue shall be made out of composite upper
material and shall be half bellow type for Type 2 and
full bellow type for Type 1.) |
- |
0 |
|
Clause Repeated |
| Cl.5.3.5 Outer toe cap( shall be provided which is made
of polymer/rubber and it shall be strongly adhered such
that it shall not open up or come out while in use. Toe
of the boot shall be reinforced with safety toe cap) |
- |
0 |
|
Clause Repeated |
| Cl.5.3.6( A designed foxing of width of minimum 25 mm
and of thickness of minimum 2 mm is to be provided.
The foxing shall not extend the edges of the outer
sole.) |
- |
0 |
|
Clause Repeated |
| Cl.5.3.7( Two pairs of detachable insocks are to be
provided. The insocks shall be compact in nature having
thickness not less than 2 mm.) |
- |
0 |
|
Clause Repeated |
| Cl.5.4 Finish(
In appearance, general workmanship and in all other
respects with regard to finish and get up of the footwear,
the footwear shall be matching to the approved sample
of the purchaser.) |
- |
0 |
|
Clause Repeated |
| Cl.5.5 Mass(The mass of one pair of finished footwear of size 8
shall not exceed 1 500 g for Type 1 and 1 400 g for
Type 2 with an increase or decrease of 100 g for each
bigger or smaller size, respectively.) |
- |
0 |
|
Clause Repeated |
| Cl.5.6( Height of Upper
Height of upper of the boots shall conform to column 5
(Design C) and column 4 (Design B) of 5.2.2, Table 4
of IS 15298 (Part 2) for Type 1 and Type 2, respectively
when measured as per 6.2 of IS 15298 (Part 1) on the
inside of the back of the footwear and from seat of the
insole to top edge of the upper.) |
- |
0 |
|
Clause Repeated |
| Cl.5.7 Performance Test(When safety footwear is tested in accordance with the
method described in 5.4 of IS 15298 (Part 1), at an
impact energy of (200 ± 4) J, the clearance under the
toecap at the moment of impact shall be in accordance
with Table 5. In addition, the toecap shall not develop
any cracks which go through the material, that is,
through which light can be seen.) |
- |
0 |
|
Clause Repeated |
| Cl.5.8 Upper/Outsole Bond Strength(When the footwear is tested in accordance with the
method prescribed in 5.2 of IS 15298 (Part 1), the bond
strength shall not be less than 4.0 N/mm, unless there
is tearing of the sole in which case the bond strength
shall not be less than 3.0 N/mm.) |
- |
0 |
|
Clause Repeated |
| Cl.5.9 Sole Interlayer Bond Strength for Bi-polymer(
and Bi-density Sole
When tested in accordance with 5.2 of IS 15298 (Part 1),
the bond strength between the outer or cleated layer
and the adjacent layer shall not be less than 4.0 N/mm
unless there is tearing of any part of the sole, in which
case the bond strength shall not be less than 3.0 N/mm.) |
- |
0 |
|
Clause Repeated |
| Cl.5.10 Consolidation Test(
Representative sample of width 25 ± 0.5 mm are cut
out from the quarter of the upper along the length of
boot. The plies are separated by breaking the bond.
Carry out the test on two specimens in accordance with
IS 3400 (Part 5). Th) |
- |
0 |
|
Clause Repeated |
| Cl.5.11 Compression Resistance(
5.11.1 When safety boots are tested in accordance
with 5.5 of IS 15298 (Part 1), the clearance under the
toe cap at a compression load of 15 kN ± 0.1 kN shall
be in accordance with Table 5.) |
- |
0 |
|
Clause Repeated |
| Cl.5.12 Internal Length of Toe Cap(
For safety boots, internal length of the toe cap shall
meet the specification given in Table 5 of IS 15298
(Part 2) when tested as per 5.3 of IS 15298 (Part 1).) |
- |
0 |
|
Clause Repeated |
| Cl.6.1 Abrasion Resistance of Compact Outsole(
When outsole is tested in accordance with 8.3 of
IS 15298 (Part 1), the relative volume loss shall not
be greater than 250 mm³ for materials having density
0.9 g/cm³ or less, and not greater than 150 mm³ for
materials with density greater than 0.9 g/cm³.) |
- |
0 |
|
Clause Amended |
| Cl.6.2 Flexing Resistance of Compact Outsole(
When outsole is tested in accordance with 8.4 of
IS 15298 (Part 1), the cut growth shall not be greater
than 4 mm before 30 000 cycles.) |
- |
0 |
|
Clause Amended |
| Cl.6.4 Resistance to Hot Contact( — Sole Heel
When sole heel is tested in accordance with 8.7 of IS 15298 (Part 1), the material shall not melt/deform
and shall not develop any cracks when bent around the
mandrel.) |
- |
0 |
|
Clause Amended |
| Cl.6.5 Hydrolysis(
When bottom sole or other components are made out
of polyurethane, the same shall be tested in accordance
with 8.5 of IS 15298 (Part 1) and the same shall comply
with 5.8.5 of IS 15298 (Part 2).) |
- |
0 |
|
Clause Amended |
| Cl.5.2.5 Compact Sole Heel
Cl.5.2.5.1 IS 3400 (Part 2)(requirements prescribed in col 3 of Table 2 when tested
as per corresponding test methods prescribed in col 4
of Table 2.
i)i) Hardness (IRHD) |
- |
0 |
|
Clause Amended |
| Cl.6.3 Tear Strength of Compact Outsole(
When outsoles are tested in accordance to 8.2 of
IS 15298 (Part 1), the tear strength shall be not less
than 8 kN/m for material having density higher
than 0.9/cm³ and when density of material is less than
or equal to 0.9 g/cm³, tear strength shall not be less
than 5 kN/m.) |
- |
0 |
|
Clause Amended |
| Cl.5.2.3 Coated Binding Material
IS 1954(
Coated binding materials shall conform to the
requirements given in col 3 of Table 1 when tested
according to the methods prescribed in col 4 of Table 1.
i)Width in mm,
) |
- |
0 |
|
Clause Amended |
| Cl.5.2.1.4 ( Type 2 footwear, the composite upper
material shall comply with requirements of water coefficient as prescribed
in 5.4.6 of IS 15298 (Part 2).) |
- |
0 |
|
Clause Amended |
| Cl.5.2.1.4 ( Type 2 footwear, the composite upper
material shall comply with requirements of water
vapour permeability as prescribed
in 5.4.6 of IS 15298 (Part 2).) |
- |
0 |
|
Clause Amended |
| CL.5.2.10 Counter Stiffener(
A counter stiffener, made out of textile reinforced withpolymer/rubber including (thermoplastic) having
thickness not less than 1.5 mm is to be stitched at inside
of upper so as to fortify the back of the footwear at
joints of quarter.) |
- |
0 |
|
Clause Amended |
| Cl.5.1.1 Fittings(Fittings of the footwear shall be in conformity to Table 9
of IS 1638 (measurement of men’s lasts) and Table 8
of IS 1638 (measurement of women’s lasts).) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.1 Upper
Cl.5.2.1.1
IS 3400(Part 5)( Composite upper material shall comply with consolidation test as per 5.10.(IS 3400 (Part 5). There shall be no separation at a load
of 1.5 kg.)) |
- |
0 |
|
Clause Amended |
| Cl.5.2.1.2( Composite upper material shall comply with
tear strength as per 5.4.3 of IS 15298 (Part 2).) |
- |
0 |
|
Clause Amended |
| Cl.5.2.1.3 ,
Cl.6.5 of IS 15298 (Part 1).( Composite upper material shall develop no cracks before 150 000 cycles when tested in accordance
with 6.5 of IS 15298 (Part 1).) |
- |
0 |
|
Clause Amended |
| Cl.5.2.1.5( Inner layer of upper shall meet requirement of abrasion resistance as prescribed in 5.5.2 of IS 15298 (Part 2).) |
- |
0 |
|
Clause Amended |
| Cl.5.2.2 Compact Insole/Compact Insocks/Counter
Stiffener Lining(Textile material shall be used as lining material for
compact insole/compact insocks / counter stiffener. It
shall meet the requirement of tear strength as prescribed
in 5.6.1 of IS 15298 (Part 2).) |
- |
0 |
|
Clause Amended |
| Cl.5.2.2.1 Abrasion resistance of compact insole/insocks/
counter stiffener(
When textiles used as lining for all the above are tested
in accordance with 6.12 of IS 15298 (Part 1), the lining
shall not develop any holes before the following number
of cycles has been performed:) |
- |
0 |
|
Clause Amended |
| Cl.5.2.3.1 In case of cotton black binding materia( the same shall be free from sulphur dyes when tested in
accordance with Annex B.) |
- |
0 |
|
Clause Amended |
| Cl.5.2.5 Compact Sole Heel
Cl. 5.2.5.1
(The compact sole heel shall be made out
of polymeric/rubber components and the typical design
recommendation (not mandatory) of compact sole heel
is as shown in Fig. 3. Sectional view of Type 1/Type 2
)
toe position is given in Fig. 4.) |
- |
0 |
|
Clause Amended |
| Cl.5.2.5 Compact Sole Heel
5.2.5.1 IS 3400 (Part 4)(ii)*Change in hardness after
accelerated ageing at 100 ± 2
°C for 24 h
) |
- |
0 |
|
Clause Amended |
| Cl.5.2.5.4 Thickness of compact sole hee(Thickness of compact sole heel of the boots shall
comply with the thickness and material requirements
prescribed in Table 3.) |
- |
0 |
|
Clause Amended |
| Cl.5.2.6 Thread for Upper Closing(
The length (m/kg) and construction of sewing thread
shall conform to requirements as prescribed in
Table 4.) |
- |
0 |
|
Clause Amended |
| Cl.5.2.8.1( The boots shall be provided with laces having minimum length of 115 cm for Type 1 and minimum
100 cm for Type 2.) |
- |
0 |
|
Clause Amended |
| Cl.5.2.8.2 (Minimum breaking load of 60 kg is to be
achieved when tested between 18 cm grip length in
accordance with Annex C.) |
- |
0 |
|
Clause Amended |
| Cl.5.2.8.3( In case of cotton lace of black colour, the same
shall be free from sulphur dyes when tested in
accordance with Annex B. Two ends of the laces shall
be provided with plastic tips.) |
- |
0 |
|
Clause Amended |
| Cl.5.2.9 Eyelets(
Aluminum eyelets of external collar diameter not less
than 10 mm and wall thickness of 0.30 to 0.35 mm
shall be used.) |
- |
0 |
|
Clause Amended |
| Cl.5.3.2 (The tongue shall be made out of composite upper
material and shall be half bellow type for Type 2 and
full bellow type for Type 1.) |
- |
0 |
|
Clause Repeated |
| Cl.5.3.5 Outer toe cap( shall be provided which is made
of polymer/rubber and it shall be strongly adhered such
that it shall not open up or come out while in use. Toe
of the boot shall be reinforced with safety toe cap) |
- |
0 |
|
Clause Repeated |
| Cl.5.3.6( A designed foxing of width of minimum 25 mm
and of thickness of minimum 2 mm is to be provided.
The foxing shall not extend the edges of the outer
sole.) |
- |
0 |
|
Clause Repeated |
| Cl.5.3.7( Two pairs of detachable insocks are to be
provided. The insocks shall be compact in nature having
thickness not less than 2 mm.) |
- |
0 |
|
Clause Repeated |
| Cl.5.4 Finish(
In appearance, general workmanship and in all other
respects with regard to finish and get up of the footwear,
the footwear shall be matching to the approved sample
of the purchaser.) |
- |
0 |
|
Clause Repeated |
| Cl.5.5 Mass(The mass of one pair of finished footwear of size 8
shall not exceed 1 500 g for Type 1 and 1 400 g for
Type 2 with an increase or decrease of 100 g for each
bigger or smaller size, respectively.) |
- |
0 |
|
Clause Repeated |
| Cl.5.6( Height of Upper
Height of upper of the boots shall conform to column 5
(Design C) and column 4 (Design B) of 5.2.2, Table 4
of IS 15298 (Part 2) for Type 1 and Type 2, respectively
when measured as per 6.2 of IS 15298 (Part 1) on the
inside of the back of the footwear and from seat of the
insole to top edge of the upper.) |
- |
0 |
|
Clause Repeated |
| Cl.5.7 Performance Test(When safety footwear is tested in accordance with the
method described in 5.4 of IS 15298 (Part 1), at an
impact energy of (200 ± 4) J, the clearance under the
toecap at the moment of impact shall be in accordance
with Table 5. In addition, the toecap shall not develop
any cracks which go through the material, that is,
through which light can be seen.) |
- |
0 |
|
Clause Repeated |
| Cl.5.8 Upper/Outsole Bond Strength(When the footwear is tested in accordance with the
method prescribed in 5.2 of IS 15298 (Part 1), the bond
strength shall not be less than 4.0 N/mm, unless there
is tearing of the sole in which case the bond strength
shall not be less than 3.0 N/mm.) |
- |
0 |
|
Clause Repeated |
| Cl.5.9 Sole Interlayer Bond Strength for Bi-polymer(
and Bi-density Sole
When tested in accordance with 5.2 of IS 15298 (Part 1),
the bond strength between the outer or cleated layer
and the adjacent layer shall not be less than 4.0 N/mm
unless there is tearing of any part of the sole, in which
case the bond strength shall not be less than 3.0 N/mm.) |
- |
0 |
|
Clause Repeated |
| Cl.5.10 Consolidation Test(
Representative sample of width 25 ± 0.5 mm are cut
out from the quarter of the upper along the length of
boot. The plies are separated by breaking the bond.
Carry out the test on two specimens in accordance with
IS 3400 (Part 5). Th) |
- |
0 |
|
Clause Repeated |
| Cl.5.11 Compression Resistance(
5.11.1 When safety boots are tested in accordance
with 5.5 of IS 15298 (Part 1), the clearance under the
toe cap at a compression load of 15 kN ± 0.1 kN shall
be in accordance with Table 5.) |
- |
0 |
|
Clause Repeated |
| Cl.5.12 Internal Length of Toe Cap(
For safety boots, internal length of the toe cap shall
meet the specification given in Table 5 of IS 15298
(Part 2) when tested as per 5.3 of IS 15298 (Part 1).) |
- |
0 |
|
Clause Repeated |
| Cl.6.1 Abrasion Resistance of Compact Outsole(
When outsole is tested in accordance with 8.3 of
IS 15298 (Part 1), the relative volume loss shall not
be greater than 250 mm³ for materials having density
0.9 g/cm³ or less, and not greater than 150 mm³ for
materials with density greater than 0.9 g/cm³.) |
- |
0 |
|
Clause Amended |
| Cl.6.2 Flexing Resistance of Compact Outsole(
When outsole is tested in accordance with 8.4 of
IS 15298 (Part 1), the cut growth shall not be greater
than 4 mm before 30 000 cycles.) |
- |
0 |
|
Clause Amended |
| Cl.6.4 Resistance to Hot Contact( — Sole Heel
When sole heel is tested in accordance with 8.7 of IS 15298 (Part 1), the material shall not melt/deform
and shall not develop any cracks when bent around the
mandrel.) |
- |
0 |
|
Clause Amended |
| Cl.6.5 Hydrolysis(
When bottom sole or other components are made out
of polyurethane, the same shall be tested in accordance
with 8.5 of IS 15298 (Part 1) and the same shall comply
with 5.8.5 of IS 15298 (Part 2).) |
- |
0 |
|
Clause Amended |
| 4(Types) |
- |
0 |
|
- |
| 5(Requirements) |
- |
0 |
|
- |
| 5.10(consolidation test IS 3400 (Part 5)) |
- |
0 |
|
Clause Repeated |
| 5.2.8.4(Colour of the lace) |
- |
0 |
|
Clause Amended |
| 5.10(Consolidation Test IS 3400 (Part 5) : 1986) |
- |
0 |
|
Clause Amended |
| Cl. 5.2.4(Reinforcing Material) |
- |
0 |
|
Clause Amended |
| Cl. 5.2.8.4(Colour of the lace) |
- |
0 |
|
Clause Amended |
| Cl. 5.3(Construction 5.3.1,5.3.3,5.3.4) |
- |
0 |
|
Clause Repeated |
| 7.2(Resistance to electricity) |
- |
0 |
|
Clause Repeated |
| 5.1(Design) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.1 Upper
Cl.5.2.1.1
IS 3400(Part 5)( Composite upper material shall comply with consolidation test as per 5.10.(IS 3400 (Part 5). There shall be no separation at a load
of 1.5 kg.)) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.1 Upper
Cl.5.2.1.1
IS 3400(Part 5)( Composite upper material shall comply with consolidation test as per 5.10.(IS 3400 (Part 5). There shall be no separation at a load
of 1.5 kg.)) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.1.4 ( Type 2 footwear, the composite upper
material shall comply with requirements of water coefficient as prescribed
in 5.4.6 of IS 15298 (Part 2).) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.1.5( Inner layer of upper shall meet requirement of abrasion resistance as prescribed in 5.5.2 of IS 15298 (Part 2).) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.2 Compact Insole/Compact Insocks/Counter
Stiffener Lining(Textile material shall be used as lining material for
compact insole/compact insocks / counter stiffener. It
shall meet the requirement of tear strength as prescribed
in 5.6.1 of IS 15298 (Part 2).) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.2.1 Abrasion resistance of compact insole/insocks/
counter stiffener(
When textiles used as lining for all the above are tested
in accordance with 6.12 of IS 15298 (Part 1), the lining
shall not develop any holes before the following number
of cycles has been performed:) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.3 Coated Binding Material
IS 1954(
Coated binding materials shall conform to the
requirements given in col 3 of Table 1 when tested
according to the methods prescribed in col 4 of Table 1.
i)Width in mm,
) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.3 Coated Binding Material
Annex C(ii) Breaking load in N, Min (50 cm grip length test specimen) ) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.3.1 In case of cotton black binding materia( the same shall be free from sulphur dyes when tested in
accordance with Annex B.) |
- |
0 |
|
Clause Repeated |
| 5.2.4(Reinforcing Material) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.5 Compact Sole Heel
Cl. 5.2.5.1
(The compact sole heel shall be made out
of polymeric/rubber components and the typical design
recommendation (not mandatory) of compact sole heel
is as shown in Fig. 3. Sectional view of Type 1/Type 2
)
toe position is given in Fig. 4.) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.5 Compact Sole Heel
Cl.5.2.5.1 IS 3400 (Part 2)(requirements prescribed in col 3 of Table 2 when tested
as per corresponding test methods prescribed in col 4
of Table 2.
i)i) Hardness (IRHD) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.5 Compact Sole Heel
5.2.5.1 IS 3400 (Part 4)(ii)*Change in hardness after
accelerated ageing at 100 ± 2
°C for 24 h
) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.5.3 Ageing for whole footwear(When rubber is used for manufacturing boots or when
the outer sole heel is made of bi-polymer, the finished
boots shall be aged at 100 ± 2°C for 24 h. On completion of test, all rubber components shall not
develop any sign of tackiness or brittleness.) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.5.4 Thickness of compact sole hee(Thickness of compact sole heel of the boots shall
comply with the thickness and material requirements
prescribed in Table 3.) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.5.4 Thickness of compact sole hee(of black cotton thread, the same shall be free from
sulphur dyes when tested in accordance with
Annex B.) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.5.4 Thickness of compact sole hee(Thickness of compact sole heel of the boots shall
comply with the thickness and material requirements
prescribed in Table 3.) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.5.4 Thickness of compact sole hee(of black cotton thread, the same shall be free from
sulphur dyes when tested in accordance with
Annex B.) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.5.4 Thickness of compact sole hee(of black cotton thread, the same shall be free from
sulphur dyes when tested in accordance with
Annex B.) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.5.3 Ageing for whole footwear(When rubber is used for manufacturing boots or when
the outer sole heel is made of bi-polymer, the finished
boots shall be aged at 100 ± 2°C for 24 h. On completion of test, all rubber components shall not
develop any sign of tackiness or brittleness.) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.6 Thread for Upper Closing(
The length (m/kg) and construction of sewing thread
shall conform to requirements as prescribed in
Table 4.) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.6 Thread for Upper Closing(
The length (m/kg) and construction of sewing thread
shall conform to requirements as prescribed in
Table 4.) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.7 Safety Toe Cap(Safety toe cap as per 3.6 shall be fitted into the footwear and must not come out while in use.) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.7 Safety Toe Cap(Safety toe cap as per 3.6 shall be fitted into the footwear and must not come out while in use.) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.7 Safety Toe Cap(Safety toe cap as per 3.6 shall be fitted into the footwear and must not come out while in use.) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.8.1( The boots shall be provided with laces having minimum length of 115 cm for Type 1 and minimum
100 cm for Type 2.) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.8.2 (Minimum breaking load of 60 kg is to be
achieved when tested between 18 cm grip length in
accordance with Annex C.) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.8.3( In case of cotton lace of black colour, the same
shall be free from sulphur dyes when tested in
accordance with Annex B. Two ends of the laces shall
be provided with plastic tips.) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.9 Eyelets(
Aluminum eyelets of external collar diameter not less
than 10 mm and wall thickness of 0.30 to 0.35 mm
shall be used.) |
- |
0 |
|
Clause Repeated |
| CL.5.2.10 Counter Stiffener(
A counter stiffener, made out of textile reinforced withpolymer/rubber including (thermoplastic) having
thickness not less than 1.5 mm is to be stitched at inside
of upper so as to fortify the back of the footwear at
joints of quarter.) |
- |
0 |
|
Clause Repeated |
| 5.3, 5.3.1,5.3.3,5.3.4(Construction) |
- |
9 |
|
Clause Repeated |
| Cl.5.3.2 (The tongue shall be made out of composite upper
material and shall be half bellow type for Type 2 and
full bellow type for Type 1.) |
- |
0 |
|
Clause Repeated |
| Cl.5.3.5 Outer toe cap( shall be provided which is made
of polymer/rubber and it shall be strongly adhered such
that it shall not open up or come out while in use. Toe
of the boot shall be reinforced with safety toe cap) |
- |
-0 |
|
Clause Repeated |
| Cl.5.3.6( A designed foxing of width of minimum 25 mm
and of thickness of minimum 2 mm is to be provided.
The foxing shall not extend the edges of the outer
sole.) |
- |
0 |
|
Clause Repeated |
| Cl.5.3.7( Two pairs of detachable insocks are to be
provided. The insocks shall be compact in nature having
thickness not less than 2 mm.) |
- |
0 |
|
Clause Repeated |
| Cl.5.4 Finish(
In appearance, general workmanship and in all other
respects with regard to finish and get up of the footwear,
the footwear shall be matching to the approved sample
of the purchaser.) |
- |
0 |
|
Clause Repeated |
| Cl.5.5 Mass(The mass of one pair of finished footwear of size 8
shall not exceed 1 500 g for Type 1 and 1 400 g for
Type 2 with an increase or decrease of 100 g for each
bigger or smaller size, respectively.) |
- |
0 |
|
Clause Repeated |
| Cl.5.6( Height of Upper
Height of upper of the boots shall conform to column 5
(Design C) and column 4 (Design B) of 5.2.2, Table 4
of IS 15298 (Part 2) for Type 1 and Type 2, respectively
when measured as per 6.2 of IS 15298 (Part 1) on the
inside of the back of the footwear and from seat of the
insole to top edge of the upper.) |
- |
0 |
|
Clause Repeated |
| Cl.5.7 Performance Test(When safety footwear is tested in accordance with the
method described in 5.4 of IS 15298 (Part 1), at an
impact energy of (200 ± 4) J, the clearance under the
toecap at the moment of impact shall be in accordance
with Table 5. In addition, the toecap shall not develop
any cracks which go through the material, that is,
through which light can be seen.) |
- |
0 |
|
Clause Repeated |
| Cl.5.8 Upper/Outsole Bond Strength(When the footwear is tested in accordance with the
method prescribed in 5.2 of IS 15298 (Part 1), the bond
strength shall not be less than 4.0 N/mm, unless there
is tearing of the sole in which case the bond strength
shall not be less than 3.0 N/mm.) |
- |
0 |
|
Clause Repeated |
| Cl.5.9 Sole Interlayer Bond Strength for Bi-polymer(
and Bi-density Sole
When tested in accordance with 5.2 of IS 15298 (Part 1),
the bond strength between the outer or cleated layer
and the adjacent layer shall not be less than 4.0 N/mm
unless there is tearing of any part of the sole, in which
case the bond strength shall not be less than 3.0 N/mm.) |
- |
0 |
|
Clause Repeated |
| Cl.5.10 Consolidation Test(
Representative sample of width 25 ± 0.5 mm are cut
out from the quarter of the upper along the length of
boot. The plies are separated by breaking the bond.
Carry out the test on two specimens in accordance with
IS 3400 (Part 5). Th) |
- |
0 |
|
Clause Repeated |
| Cl.5.11 Compression Resistance(
5.11.1 When safety boots are tested in accordance
with 5.5 of IS 15298 (Part 1), the clearance under the
toe cap at a compression load of 15 kN ± 0.1 kN shall
be in accordance with Table 5.) |
- |
0 |
|
Clause Repeated |
| Cl.5.13 Energy Absorption Test(When footwear is tested in accordance with the method
prescribed in 5.14 of IS 15298 (Part 1), the energy
absorption of the seat region shall not be less than 20 J.) |
- |
0 |
|
Clause Repeated |
| 7.1(Resistance to fuel) |
- |
0 |
|
Clause Repeated |
| 8(CHEMICAL REQUIREMENTS) |
- |
0 |
|
Clause Repeated |
| 9, 9.1(BIS CERTIFICATION MARKING) |
- |
0 |
|
Clause Repeated |
| 9, 9.1(BIS CERTIFICATION MARKING) |
- |
0 |
|
Clause Repeated |
| 10(Marking) |
- |
0 |
|
Clause Repeated |
| 10(Marking) |
- |
0 |
|
Clause Repeated |
| Cl. 8 (IS 17011, Table-1 (i))(Allergenic and carcinogenic disperse dyes) |
- |
0 |
|
Clause Repeated |
| 11(Packing) |
- |
0 |
|
Clause Repeated |
| 11(PACKING) |
- |
0 |
|
Clause Repeated |
| Cl.6.3 Tear Strength of Compact Outsole(
When outsoles are tested in accordance to 8.2 of
IS 15298 (Part 1), the tear strength shall be not less
than 8 kN/m for material having density higher
than 0.9/cm³ and when density of material is less than
or equal to 0.9 g/cm³, tear strength shall not be less
than 5 kN/m.) |
- |
0 |
|
Clause Repeated |
| Cl.5.13 Energy Absorption Test(When footwear is tested in accordance with the method
prescribed in 5.14 of IS 15298 (Part 1), the energy
absorption of the seat region shall not be less than 20 J.) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.3 Coated Binding Material
IS 1954(
Coated binding materials shall conform to the
requirements given in col 3 of Table 1 when tested
according to the methods prescribed in col 4 of Table 1.
i)Width in mm,
) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.3 Coated Binding Material
Annex C(ii) Breaking load in N, Min (50 cm grip length test specimen) ) |
- |
0 |
|
Clause Repeated |
| Cl.5.13 Energy Absorption Test(When footwear is tested in accordance with the method
prescribed in 5.14 of IS 15298 (Part 1), the energy
absorption of the seat region shall not be less than 20 J.) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.3 Coated Binding Material
Annex C(ii) Breaking load in N, Min (50 cm grip length test specimen) ) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.1.4 ( Type 2 footwear, the composite upper
material shall comply with requirements of water
vapour permeability as prescribed
in 5.4.6 of IS 15298 (Part 2).) |
- |
0 |
|
Clause Repeated |
| CL.5.2.10 Counter Stiffener(
A counter stiffener, made out of textile reinforced withpolymer/rubber including (thermoplastic) having
thickness not less than 1.5 mm is to be stitched at inside
of upper so as to fortify the back of the footwear at
joints of quarter.) |
- |
0 |
|
Clause Repeated |
| Cl.5.1.1 Fittings(Fittings of the footwear shall be in conformity to Table 9
of IS 1638 (measurement of men’s lasts) and Table 8
of IS 1638 (measurement of women’s lasts).) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.5.3 Ageing for whole footwear(When rubber is used for manufacturing boots or when
the outer sole heel is made of bi-polymer, the finished
boots shall be aged at 100 ± 2°C for 24 h. On completion of test, all rubber components shall not
develop any sign of tackiness or brittleness.) |
- |
0 |
|
Clause Repeated |
| Cl.5.12 Internal Length of Toe Cap(
For safety boots, internal length of the toe cap shall
meet the specification given in Table 5 of IS 15298
(Part 2) when tested as per 5.3 of IS 15298 (Part 1).) |
- |
2000 |
|
Slip Resistance |
| Cl.6.1 Abrasion Resistance of Compact Outsole(
When outsole is tested in accordance with 8.3 of
IS 15298 (Part 1), the relative volume loss shall not
be greater than 250 mm³ for materials having density
0.9 g/cm³ or less, and not greater than 150 mm³ for
materials with density greater than 0.9 g/cm³.) |
- |
0 |
|
Clause Repeated |
| Cl.6.2 Flexing Resistance of Compact Outsole(
When outsole is tested in accordance with 8.4 of
IS 15298 (Part 1), the cut growth shall not be greater
than 4 mm before 30 000 cycles.) |
- |
0 |
|
Clause Repeated |
| Cl.6.4 Resistance to Hot Contact( — Sole Heel
When sole heel is tested in accordance with 8.7 of IS 15298 (Part 1), the material shall not melt/deform
and shall not develop any cracks when bent around the
mandrel.) |
- |
0 |
|
Clause Repeated |
| Cl.6.5 Hydrolysis(
When bottom sole or other components are made out
of polyurethane, the same shall be tested in accordance
with 8.5 of IS 15298 (Part 1) and the same shall comply
with 5.8.5 of IS 15298 (Part 2).) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.5 Compact Sole Heel
Cl.5.2.5.1 IS 3400 (Part 2)(requirements prescribed in col 3 of Table 2 when tested
as per corresponding test methods prescribed in col 4
of Table 2.
i)i) Hardness (IRHD) |
- |
0 |
|
Clause Repeated |
| Cl.6.3 Tear Strength of Compact Outsole(
When outsoles are tested in accordance to 8.2 of
IS 15298 (Part 1), the tear strength shall be not less
than 8 kN/m for material having density higher
than 0.9/cm³ and when density of material is less than
or equal to 0.9 g/cm³, tear strength shall not be less
than 5 kN/m.) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.1.4 ( Type 2 footwear, the composite upper
material shall comply with requirements of water coefficient as prescribed
in 5.4.6 of IS 15298 (Part 2).) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.1.4 ( Type 2 footwear, the composite upper
material shall comply with requirements of water
vapour permeability as prescribed
in 5.4.6 of IS 15298 (Part 2).) |
- |
0 |
|
Clause Repeated |
| Cl.5.1.1 Fittings(Fittings of the footwear shall be in conformity to Table 9
of IS 1638 (measurement of men’s lasts) and Table 8
of IS 1638 (measurement of women’s lasts).) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.1.2( Composite upper material shall comply with
tear strength as per 5.4.3 of IS 15298 (Part 2).) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.1.3 ,
Cl.6.5 of IS 15298 (Part 1).( Composite upper material shall develop no cracks before 150 000 cycles when tested in accordance
with 6.5 of IS 15298 (Part 1).) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.1.5( Inner layer of upper shall meet requirement of abrasion resistance as prescribed in 5.5.2 of IS 15298 (Part 2).) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.2 Compact Insole/Compact Insocks/Counter
Stiffener Lining(Textile material shall be used as lining material for
compact insole/compact insocks / counter stiffener. It
shall meet the requirement of tear strength as prescribed
in 5.6.1 of IS 15298 (Part 2).) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.2.1 Abrasion resistance of compact insole/insocks/
counter stiffener(
When textiles used as lining for all the above are tested
in accordance with 6.12 of IS 15298 (Part 1), the lining
shall not develop any holes before the following number
of cycles has been performed:) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.3.1 In case of cotton black binding materia( the same shall be free from sulphur dyes when tested in
accordance with Annex B.) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.5 Compact Sole Heel
Cl. 5.2.5.1
(The compact sole heel shall be made out
of polymeric/rubber components and the typical design
recommendation (not mandatory) of compact sole heel
is as shown in Fig. 3. Sectional view of Type 1/Type 2
)
toe position is given in Fig. 4.) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.5 Compact Sole Heel
5.2.5.1 IS 3400 (Part 4)(ii)*Change in hardness after
accelerated ageing at 100 ± 2
°C for 24 h
) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.8.1( The boots shall be provided with laces having minimum length of 115 cm for Type 1 and minimum
100 cm for Type 2.) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.8.2 (Minimum breaking load of 60 kg is to be
achieved when tested between 18 cm grip length in
accordance with Annex C.) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.8.3( In case of cotton lace of black colour, the same
shall be free from sulphur dyes when tested in
accordance with Annex B. Two ends of the laces shall
be provided with plastic tips.) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.9 Eyelets(
Aluminum eyelets of external collar diameter not less
than 10 mm and wall thickness of 0.30 to 0.35 mm
shall be used.) |
- |
0 |
|
Clause Repeated |
| Cl.5.3.2 (The tongue shall be made out of composite upper
material and shall be half bellow type for Type 2 and
full bellow type for Type 1.) |
- |
0 |
|
Clause Repeated |
| Cl.5.3.5 Outer toe cap( shall be provided which is made
of polymer/rubber and it shall be strongly adhered such
that it shall not open up or come out while in use. Toe
of the boot shall be reinforced with safety toe cap) |
- |
0 |
|
Clause Repeated |
| Cl.5.3.6( A designed foxing of width of minimum 25 mm
and of thickness of minimum 2 mm is to be provided.
The foxing shall not extend the edges of the outer
sole.) |
- |
0 |
|
Clause Repeated |
| Cl.5.3.7( Two pairs of detachable insocks are to be
provided. The insocks shall be compact in nature having
thickness not less than 2 mm.) |
- |
0 |
|
Clause Repeated |
| Cl.5.4 Finish(
In appearance, general workmanship and in all other
respects with regard to finish and get up of the footwear,
the footwear shall be matching to the approved sample
of the purchaser.) |
- |
0 |
|
Clause Repeated |
| Cl.5.5 Mass(The mass of one pair of finished footwear of size 8
shall not exceed 1 500 g for Type 1 and 1 400 g for
Type 2 with an increase or decrease of 100 g for each
bigger or smaller size, respectively.) |
- |
0 |
|
Clause Repeated |
| Cl.5.6( Height of Upper
Height of upper of the boots shall conform to column 5
(Design C) and column 4 (Design B) of 5.2.2, Table 4
of IS 15298 (Part 2) for Type 1 and Type 2, respectively
when measured as per 6.2 of IS 15298 (Part 1) on the
inside of the back of the footwear and from seat of the
insole to top edge of the upper.) |
- |
0 |
|
Clause Repeated |
| Cl.5.7 Performance Test(When safety footwear is tested in accordance with the
method described in 5.4 of IS 15298 (Part 1), at an
impact energy of (200 ± 4) J, the clearance under the
toecap at the moment of impact shall be in accordance
with Table 5. In addition, the toecap shall not develop
any cracks which go through the material, that is,
through which light can be seen.) |
- |
0 |
|
Clause Repeated |
| Cl.5.8 Upper/Outsole Bond Strength(When the footwear is tested in accordance with the
method prescribed in 5.2 of IS 15298 (Part 1), the bond
strength shall not be less than 4.0 N/mm, unless there
is tearing of the sole in which case the bond strength
shall not be less than 3.0 N/mm.) |
- |
0 |
|
Clause Repeated |
| Cl.5.9 Sole Interlayer Bond Strength for Bi-polymer(
and Bi-density Sole
When tested in accordance with 5.2 of IS 15298 (Part 1),
the bond strength between the outer or cleated layer
and the adjacent layer shall not be less than 4.0 N/mm
unless there is tearing of any part of the sole, in which
case the bond strength shall not be less than 3.0 N/mm.) |
- |
0 |
|
Clause Repeated |
| Cl.5.10 Consolidation Test(
Representative sample of width 25 ± 0.5 mm are cut
out from the quarter of the upper along the length of
boot. The plies are separated by breaking the bond.
Carry out the test on two specimens in accordance with
IS 3400 (Part 5). Th) |
- |
0 |
|
Clause Repeated |
| Cl.5.11 Compression Resistance(
5.11.1 When safety boots are tested in accordance
with 5.5 of IS 15298 (Part 1), the clearance under the
toe cap at a compression load of 15 kN ± 0.1 kN shall
be in accordance with Table 5.) |
- |
0 |
|
Clause Repeated |
| Cl.5.12 Internal Length of Toe Cap(
For safety boots, internal length of the toe cap shall
meet the specification given in Table 5 of IS 15298
(Part 2) when tested as per 5.3 of IS 15298 (Part 1).) |
- |
0 |
|
Clause Repeated |
| Cl.6.1 Abrasion Resistance of Compact Outsole(
When outsole is tested in accordance with 8.3 of
IS 15298 (Part 1), the relative volume loss shall not
be greater than 250 mm³ for materials having density
0.9 g/cm³ or less, and not greater than 150 mm³ for
materials with density greater than 0.9 g/cm³.) |
- |
0 |
|
Clause Repeated |
| Cl.6.2 Flexing Resistance of Compact Outsole(
When outsole is tested in accordance with 8.4 of
IS 15298 (Part 1), the cut growth shall not be greater
than 4 mm before 30 000 cycles.) |
- |
0 |
|
Clause Repeated |
| Cl.6.4 Resistance to Hot Contact( — Sole Heel
When sole heel is tested in accordance with 8.7 of IS 15298 (Part 1), the material shall not melt/deform
and shall not develop any cracks when bent around the
mandrel.) |
- |
0 |
|
Clause Repeated |
| Cl.6.5 Hydrolysis(
When bottom sole or other components are made out
of polyurethane, the same shall be tested in accordance
with 8.5 of IS 15298 (Part 1) and the same shall comply
with 5.8.5 of IS 15298 (Part 2).) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.5 Compact Sole Heel
Cl.5.2.5.1 IS 3400 (Part 2)(requirements prescribed in col 3 of Table 2 when tested
as per corresponding test methods prescribed in col 4
of Table 2.
i)i) Hardness (IRHD) |
- |
0 |
|
Clause Repeated |
| Cl.6.3 Tear Strength of Compact Outsole(
When outsoles are tested in accordance to 8.2 of
IS 15298 (Part 1), the tear strength shall be not less
than 8 kN/m for material having density higher
than 0.9/cm³ and when density of material is less than
or equal to 0.9 g/cm³, tear strength shall not be less
than 5 kN/m.) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.3 Coated Binding Material
IS 1954(
Coated binding materials shall conform to the
requirements given in col 3 of Table 1 when tested
according to the methods prescribed in col 4 of Table 1.
i)Width in mm,
) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.1.4 ( Type 2 footwear, the composite upper
material shall comply with requirements of water coefficient as prescribed
in 5.4.6 of IS 15298 (Part 2).) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.1.4 ( Type 2 footwear, the composite upper
material shall comply with requirements of water
vapour permeability as prescribed
in 5.4.6 of IS 15298 (Part 2).) |
- |
0 |
|
Clause Repeated |
| CL.5.2.10 Counter Stiffener(
A counter stiffener, made out of textile reinforced withpolymer/rubber including (thermoplastic) having
thickness not less than 1.5 mm is to be stitched at inside
of upper so as to fortify the back of the footwear at
joints of quarter.) |
- |
0 |
|
Clause Repeated |
| Cl.5.1.1 Fittings(Fittings of the footwear shall be in conformity to Table 9
of IS 1638 (measurement of men’s lasts) and Table 8
of IS 1638 (measurement of women’s lasts).) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.1 Upper
Cl.5.2.1.1
IS 3400(Part 5)( Composite upper material shall comply with consolidation test as per 5.10.(IS 3400 (Part 5). There shall be no separation at a load
of 1.5 kg.)) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.1.2( Composite upper material shall comply with
tear strength as per 5.4.3 of IS 15298 (Part 2).) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.1.3 ,
Cl.6.5 of IS 15298 (Part 1).( Composite upper material shall develop no cracks before 150 000 cycles when tested in accordance
with 6.5 of IS 15298 (Part 1).) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.1.5( Inner layer of upper shall meet requirement of abrasion resistance as prescribed in 5.5.2 of IS 15298 (Part 2).) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.2 Compact Insole/Compact Insocks/Counter
Stiffener Lining(Textile material shall be used as lining material for
compact insole/compact insocks / counter stiffener. It
shall meet the requirement of tear strength as prescribed
in 5.6.1 of IS 15298 (Part 2).) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.2.1 Abrasion resistance of compact insole/insocks/
counter stiffener(
When textiles used as lining for all the above are tested
in accordance with 6.12 of IS 15298 (Part 1), the lining
shall not develop any holes before the following number
of cycles has been performed:) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.3.1 In case of cotton black binding materia( the same shall be free from sulphur dyes when tested in
accordance with Annex B.) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.5 Compact Sole Heel
Cl. 5.2.5.1
(The compact sole heel shall be made out
of polymeric/rubber components and the typical design
recommendation (not mandatory) of compact sole heel
is as shown in Fig. 3. Sectional view of Type 1/Type 2
)
toe position is given in Fig. 4.) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.5 Compact Sole Heel
5.2.5.1 IS 3400 (Part 4)(ii)*Change in hardness after
accelerated ageing at 100 ± 2
°C for 24 h
) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.5.4 Thickness of compact sole hee(Thickness of compact sole heel of the boots shall
comply with the thickness and material requirements
prescribed in Table 3.) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.6 Thread for Upper Closing(
The length (m/kg) and construction of sewing thread
shall conform to requirements as prescribed in
Table 4.) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.8.1( The boots shall be provided with laces having minimum length of 115 cm for Type 1 and minimum
100 cm for Type 2.) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.8.2 (Minimum breaking load of 60 kg is to be
achieved when tested between 18 cm grip length in
accordance with Annex C.) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.8.3( In case of cotton lace of black colour, the same
shall be free from sulphur dyes when tested in
accordance with Annex B. Two ends of the laces shall
be provided with plastic tips.) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.9 Eyelets(
Aluminum eyelets of external collar diameter not less
than 10 mm and wall thickness of 0.30 to 0.35 mm
shall be used.) |
- |
0 |
|
Clause Repeated |
| Cl.5.3.2 (The tongue shall be made out of composite upper
material and shall be half bellow type for Type 2 and
full bellow type for Type 1.) |
- |
0 |
|
Clause Repeated |
| Cl.5.3.5 Outer toe cap( shall be provided which is made
of polymer/rubber and it shall be strongly adhered such
that it shall not open up or come out while in use. Toe
of the boot shall be reinforced with safety toe cap) |
- |
0 |
|
Clause Repeated |
| Cl.5.3.6( A designed foxing of width of minimum 25 mm
and of thickness of minimum 2 mm is to be provided.
The foxing shall not extend the edges of the outer
sole.) |
- |
0 |
|
Clause Repeated |
| Cl.5.3.7( Two pairs of detachable insocks are to be
provided. The insocks shall be compact in nature having
thickness not less than 2 mm.) |
- |
0 |
|
Clause Repeated |
| Cl.5.4 Finish(
In appearance, general workmanship and in all other
respects with regard to finish and get up of the footwear,
the footwear shall be matching to the approved sample
of the purchaser.) |
- |
0 |
|
Clause Repeated |
| Cl.5.5 Mass(The mass of one pair of finished footwear of size 8
shall not exceed 1 500 g for Type 1 and 1 400 g for
Type 2 with an increase or decrease of 100 g for each
bigger or smaller size, respectively.) |
- |
0 |
|
Clause Repeated |
| Cl.5.6( Height of Upper
Height of upper of the boots shall conform to column 5
(Design C) and column 4 (Design B) of 5.2.2, Table 4
of IS 15298 (Part 2) for Type 1 and Type 2, respectively
when measured as per 6.2 of IS 15298 (Part 1) on the
inside of the back of the footwear and from seat of the
insole to top edge of the upper.) |
- |
0 |
|
Clause Repeated |
| Cl.5.7 Performance Test(When safety footwear is tested in accordance with the
method described in 5.4 of IS 15298 (Part 1), at an
impact energy of (200 ± 4) J, the clearance under the
toecap at the moment of impact shall be in accordance
with Table 5. In addition, the toecap shall not develop
any cracks which go through the material, that is,
through which light can be seen.) |
- |
0 |
|
Clause Repeated |
| Cl.5.8 Upper/Outsole Bond Strength(When the footwear is tested in accordance with the
method prescribed in 5.2 of IS 15298 (Part 1), the bond
strength shall not be less than 4.0 N/mm, unless there
is tearing of the sole in which case the bond strength
shall not be less than 3.0 N/mm.) |
- |
0 |
|
Clause Repeated |
| Cl.5.9 Sole Interlayer Bond Strength for Bi-polymer(
and Bi-density Sole
When tested in accordance with 5.2 of IS 15298 (Part 1),
the bond strength between the outer or cleated layer
and the adjacent layer shall not be less than 4.0 N/mm
unless there is tearing of any part of the sole, in which
case the bond strength shall not be less than 3.0 N/mm.) |
- |
0 |
|
Clause Repeated |
| Cl.5.10 Consolidation Test(
Representative sample of width 25 ± 0.5 mm are cut
out from the quarter of the upper along the length of
boot. The plies are separated by breaking the bond.
Carry out the test on two specimens in accordance with
IS 3400 (Part 5). Th) |
- |
0 |
|
Clause Repeated |
| Cl.5.11 Compression Resistance(
5.11.1 When safety boots are tested in accordance
with 5.5 of IS 15298 (Part 1), the clearance under the
toe cap at a compression load of 15 kN ± 0.1 kN shall
be in accordance with Table 5.) |
- |
0 |
|
Clause Repeated |
| Cl.5.12 Internal Length of Toe Cap(
For safety boots, internal length of the toe cap shall
meet the specification given in Table 5 of IS 15298
(Part 2) when tested as per 5.3 of IS 15298 (Part 1).) |
- |
0 |
|
Clause Repeated |
| Cl.6.1 Abrasion Resistance of Compact Outsole(
When outsole is tested in accordance with 8.3 of
IS 15298 (Part 1), the relative volume loss shall not
be greater than 250 mm³ for materials having density
0.9 g/cm³ or less, and not greater than 150 mm³ for
materials with density greater than 0.9 g/cm³.) |
- |
0 |
|
Clause Repeated |
| Cl.6.2 Flexing Resistance of Compact Outsole(
When outsole is tested in accordance with 8.4 of
IS 15298 (Part 1), the cut growth shall not be greater
than 4 mm before 30 000 cycles.) |
- |
0 |
|
Clause Repeated |
| Cl.6.4 Resistance to Hot Contact( — Sole Heel
When sole heel is tested in accordance with 8.7 of IS 15298 (Part 1), the material shall not melt/deform
and shall not develop any cracks when bent around the
mandrel.) |
- |
0 |
|
Clause Repeated |
| Cl.6.5 Hydrolysis(
When bottom sole or other components are made out
of polyurethane, the same shall be tested in accordance
with 8.5 of IS 15298 (Part 1) and the same shall comply
with 5.8.5 of IS 15298 (Part 2).) |
- |
0 |
|
Clause Repeated |
| 4(Types) |
- |
0 |
|
Clause Repeated |
| 5(Requirements) |
- |
0 |
|
Clause Repeated |
| 5.10(consolidation test IS 3400 (Part 5)) |
- |
0 |
|
Clause Repeated |
| 5.2.8.4(Colour of the lace) |
- |
0 |
|
Clause Repeated |
| 5.10(Consolidation Test IS 3400 (Part 5) : 1986) |
- |
0 |
|
Clause Repeated |
| Cl. 5.2.4(Reinforcing Material) |
- |
0 |
|
Clause Repeated |
| Cl. 5.2.8.4(Colour of the lace) |
- |
0 |
|
Clause Repeated |
| Cl. 5.3(Construction 5.3.1,5.3.3,5.3.4) |
- |
0 |
|
Clause Repeated |
| 7.2(Resistance to electricity) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.1.2( Composite upper material shall comply with
tear strength as per 5.4.3 of IS 15298 (Part 2).) |
- |
0 |
|
Clause Repeated |
| Cl.5.2.1.3 ,
Cl.6.5 of IS 15298 (Part 1).( Composite upper material shall develop no cracks before 150 000 cycles when tested in accordance
with 6.5 of IS 15298 (Part 1).) |
- |
0 |
|
Clause Repeated |
|
- |
-
Included w.e.f 18.12.2024 |
| 9880 |
Delta Testing and Research Laboratories Private Limited (C5)
| 9179506
| IS 1239 : Part 2 (2011) |
Steel tubes, tubulars and other steel fittings - Specification: Part 2 steel pipe fittings (Fifth Revision) |
All Grade / Type / Size / Designation |
8400 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 7.1(Chemical Composition - Sulphur - Laddle Analysis IS 228) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1(Chemical Composition - Phosphorus - Laddle Analysis IS 228) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.1-Table 1( DIMENSIONS OF TUBULARS-Pieces
) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.1-Table 1( DIMENSIONS OF TUBULARS-Pieces-Approximate Standard Length(A)
) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.2-Table-2( DIMENSIONS OF TUBULARS-Nipples
) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.2-Table-2( DIMENSIONS OF TUBULARS-Nipples-A
) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.2-Table-2( DIMENSIONS OF TUBULARS-Nipples-B
) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.2-Table-2( DIMENSIONS OF TUBULARS-Nipples-C
) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.3.1-Table 3(DIMENSIONS OF TUBULARS-Longscrews (Connectors)) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.3.1-Table 3(DIMENSIONS OF TUBULARS-Longscrews (Connectors)-A) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.3.1-Table 3(DIMENSIONS OF TUBULARS-Longscrews (Connectors)-B) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.3.1-Table 3(DIMENSIONS OF TUBULARS-Longscrews (Connectors)-C) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.3.2(DIMENSIONS OF TUBULARS-Longscrews (Connectors)) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.3.2(DIMENSIONS OF TUBULARS-Longscrews (Connectors)-The face of the back nut angle) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.4.1 -Table 4(Bends and springs) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.4.1 -Table 4(Bends and springs-A) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.4.1 -Table 4(Bends and springs-B) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.4.1 -Table 4(Bends and springs-R) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.4.1 -Table 4(Bends and springs-C) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.4.1 -Table 4(Bends and springs-D) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.4.1 -Table 4(Bends and springs-E) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.5-Table 5( Return Bends) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.5-Table 5( Return Bends-A) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.5-Table 5( Return Bends-B) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.6 -Table 6(Sockets) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.6 -Table 6(Sockets-A) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.6 -Table 6(Sockets-B) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.6 -Table 6(Maximum Inside Diameter of Internal Parallel Thread) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9(DIMENSIONS OF STEEL FITTINGS (OTHER THAN TUBULARS)) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 7(Dimensions of Screwed Ends of Fittings-D
) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 7(Dimensions of Screwed Ends of Fittings-E
) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 7(Dimensions of Screwed Ends of Fittings-d
) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 7(Dimensions of Screwed Ends of Fittings-Taper
) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 8 (Dimensions of Elbows, Tees and Crosses, Equal-A) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 9 (Dimensions of Elbows Reducing-A) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 9 (Dimensions of Elbows Reducing-B) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 10 (Dimensions of Tees, Reducing (on the Branch)-A) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 10 (Dimensions of Tees, Reducing (on the Branch)-B) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 11 (Dimensions of Tees, Reducing (on the Run and Branch, or on the Run Only)-A) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 11 (Dimensions of Tees, Reducing (on the Run and Branch, or on the Run Only)-B) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 12(Dimensions of Tees (Increasing on the Branch)-A) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 12(Dimensions of Tees (Increasing on the Branch)-B) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 13( Dimensions of Crosses, Reducing-A) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 13( Dimensions of Crosses, Reducing-B) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 14( Elbows, Tees and Crosses, Side Outlet, Equal-A) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 14( Elbows, Tees and Crosses, Side Outlet, Equal-B) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 15( Dimensions of Elbows, Round, Male and Female, Equal-A) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 15( Dimensions of Elbows, Round, Male and Female, Equal-B) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 15( Dimensions of Elbows, Round, Male and Female, Equal-Minimum Bore of Male End) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 15( Dimensions of Elbows, Round, Male and Female, Equal-Maximum Bore of Male End) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 16( Dimensions of Elbows, Equal, 135°-A) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 17 (Dimensions of Y-Pieces, Female, Equal-A) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 18 (Dimensions of Socket, Reducing-A) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 19 (Dimensions of Caps-A) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 19 (Dimensions of Caps-T) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 20(Dimensions of Plug-Minimum Length of Thread for Basic Gauge) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 20(Dimensions of Plug-Minimum Length of Thread for Basic Gauge-S) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 20(Dimensions of Plug-Minimum Length of Thread for Basic Gauge-H) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 20(Dimensions of Plug-Minimum Length of Thread for Basic Gauge-D) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 20(Dimensions of Plug-Minimum Length of Thread for Basic Gauge-K) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 21 (Dimensions of Elbows, Tees and Crosses, Male, Equal-A) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 22(Dimensions of Y-Pieces and Angle Tees, Male, Equal-A
) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 22(Dimensions of Y-Pieces and Angle Tees, Male, Equal-B
) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 23( Dimensions of Twin Elbows and Sweep Tees, Male, Equal-A) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 23( Dimensions of Twin Elbows and Sweep Tees, Male, Equal-B) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 24(Dimensions of Socket Unions-A
) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 25 (Dimensions of Pipe Unions-A) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 26 (Dimensions of Union Bends-A
) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 26 (Dimensions of Union Bends-B
) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 27 (Dimensions of Hexagon Bushes-L) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 27 (Dimensions of Hexagon Bushes-T) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 27 (Dimensions of Hexagon Bushes-A) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 27 (Dimensions of Hexagon Bushes-B) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 28 (Dimensions of Nipples, Hexagon, Equal-L) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 28 (Dimensions of Nipples, Hexagon, Equal-T) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 28 (Dimensions of Nipples, Hexagon, Equal-A) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 28 (Dimensions of Nipples, Hexagon, Equal-C) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1-Table 28 (Dimensions of Nipples, Hexagon, Equal-B) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 11.1(a)(Internal hydraulic Pressure Test) |
- |
1250 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 11.1(a)(Internal Air Pressure Test) |
- |
1250 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 11.2.1( Drift Expanding Test) |
- |
1250 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 11.2.2 (Taper Screw Plug Test) |
- |
1250 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 14(WORKMANSHIP) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 14(WORKMANSHIP) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 14(WORKMANSHIP) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 13 and as per IS 4736(UNIFORMITY OF ZINC COATING) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 13 and as per IS 4736(MASS OF ZINC COATING) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Clause 13.1.3 (Adhesion Test) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Clause 10(Joints ) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Clause 9.2.3 (Threads tolerance ) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Clause 9.2.2 (Tolerance for alignment of threads ) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Clause 9.1, Table- 27(Normal Size (Internal Threads) (Dimensions of Hexagon Bushes) ) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Clause 9.1, Table- 27(Normal Size (External Threads) (Dimensions of Hexagon Bushes) ) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Clause 8.3.3(Parallel threads ) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
|
21 Aug, 2027 |
-
- |
| 9881 |
Bharat Test House Pvt Ltd 1474 Sonipat Haryana
| 9135626
| IS 302 : Part 2 : Sec 7 (2024) |
Safety of Household And Similar Electrical Appliances Part 2 Particular Requirements Section 7: Domestic Electric Clothes Washing Machines |
Domestic electric clothes washing machines |
195000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 4(GENERAL REQUIREMENT) |
- |
1000 |
|
5% discount for BIS |
| 6(CLASSIFICATION) |
- |
1000 |
|
5% discount for BIS |
| 7(MARKING AND INSTRUCTIONS) |
- |
2000 |
|
5% discount for BIS |
| 8(PROTECTION AGAINST ACCESS TO LIVE PARTS) |
- |
2500 |
|
5% discount for BIS |
| 10(POWER INPUT AND CURRENT) |
- |
4000 |
|
5% discount for BIS |
| 11(HEATING) |
- |
5000 |
|
5% discount for BIS |
| 13(LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING TEMPERATURE) |
- |
4500 |
|
5% discount for BIS |
| 14(TRANSIENT OVERVOLTAGES) |
- |
5500 |
|
5% discount for BIS |
| 15(MOISTURE RESISTANCE) |
- |
15000 |
|
5% discount for BIS |
| 16(LEAKAGE CURRENT AND ELECTRIC STRENGTH) |
- |
5000 |
|
5% discount for BIS |
| 17("OVERLOAD PROTECTION OF
TRANSFORMERS AND ASSOCIATED CIRCUITS ") |
- |
4000 |
|
5% discount for BIS |
| 17("OVERLOAD PROTECTION OF
TRANSFORMERS AND ASSOCIATED CIRCUITS ") |
- |
4000 |
|
5% discount for BIS |
| 18(ENDURANCE) |
- |
10000 |
|
5% discount for BIS |
| 19(ABNORMAL OPERATION) |
- |
45000 |
|
5% discount for BIS |
| 19.11.4.1(Electrostatic discharges) |
- |
45000 |
|
5% discount for BIS |
| 19.11.4.2(Radiated fields) |
- |
45000 |
|
5% discount for BIS |
| 19.11.4.5(Immunity to conducted discharges) |
- |
45000 |
|
5% discount for BIS |
| 19.11.4.6(Class 3 Voltage dips and interruptions) |
- |
45000 |
|
5% discount for BIS |
| 19.11.4.7(Harmonics) |
- |
45000 |
|
5% discount for BIS |
| 20(STABILITY AND MECHANICAL HAZARDS) |
- |
30000 |
|
5% discount for BIS |
| 21(MECHANICAL STRENGTH) |
- |
5000 |
|
5% discount for BIS |
| 22(CONSTRUCTION) |
- |
30000 |
|
5% discount for BIS |
| 23(INTERNAL WIRING) |
- |
2500 |
|
5% discount for BIS |
| 24(COMPONENTS) |
- |
2500 |
|
5% discount for BIS |
| 25(SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CORDS) |
- |
2500 |
|
5% discount for BIS |
| 26(TERMINALS FOR EXTERNAL CONDUCTORS) |
- |
3000 |
|
5% discount for BIS |
| 27(PROVISION FOR EARTHING) |
- |
3000 |
|
5% discount for BIS |
| 28(SCREWS AND CONNECTIONS) |
- |
3000 |
|
5% discount for BIS |
| 29(CLEARANCES, CREEPAGE DISTANCES AND SOLID INSULATION) |
- |
2500 |
|
5% discount for BIS |
| 30(RESISTANCE TO HEAT AND FIRE) |
- |
3000 |
|
5% discount for BIS |
| 31(RESISTANCE TO RUSTING) |
- |
2500 |
|
5% discount for BIS |
| 4(GENERAL REQUIREMENT) |
- |
0 |
|
- |
| 6(CLASSIFICATION) |
- |
0 |
|
- |
| 7(MARKING AND INSTRUCTIONS) |
- |
0 |
|
- |
| 8(PROTECTION AGAINST ACCESS TO LIVE PARTS) |
- |
0 |
|
- |
| 10(POWER INPUT AND CURRENT) |
- |
0 |
|
- |
| 11(HEATING) |
- |
0 |
|
- |
| 13(LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING TEMPERATURE) |
- |
0 |
|
- |
| 14(TRANSIENT OVERVOLTAGES) |
- |
0 |
|
- |
| 15(MOISTURE RESISTANCE) |
- |
0 |
|
- |
| 16(LEAKAGE CURRENT AND ELECTRIC STRENGTH) |
- |
0 |
|
- |
| 17("OVERLOAD PROTECTION OF
TRANSFORMERS AND ASSOCIATED CIRCUITS ") |
- |
0 |
|
- |
| 17("OVERLOAD PROTECTION OF
TRANSFORMERS AND ASSOCIATED CIRCUITS ") |
- |
0 |
|
- |
| 18(ENDURANCE) |
- |
0 |
|
- |
| 19(ABNORMAL OPERATION) |
- |
0 |
|
- |
| 19.11.4.1(Electrostatic discharges) |
- |
0 |
|
- |
| 19.11.4.2(Radiated fields) |
- |
0 |
|
- |
| 19.11.4.5(Immunity to conducted discharges) |
- |
0 |
|
- |
| 19.11.4.6(Class 3 Voltage dips and interruptions) |
- |
0 |
|
- |
| 19.11.4.7(Harmonics) |
- |
0 |
|
- |
| 20(STABILITY AND MECHANICAL HAZARDS) |
- |
0 |
|
- |
| 21(MECHANICAL STRENGTH) |
- |
0 |
|
- |
| 22(CONSTRUCTION) |
- |
0 |
|
- |
| 23(INTERNAL WIRING) |
- |
0 |
|
- |
| 25(SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CORDS) |
- |
0 |
|
- |
| 26(TERMINALS FOR EXTERNAL CONDUCTORS) |
- |
0 |
|
- |
| 27(PROVISION FOR EARTHING) |
- |
0 |
|
- |
| 28(SCREWS AND CONNECTIONS) |
- |
0 |
|
- |
| 29(CLEARANCES, CREEPAGE DISTANCES AND SOLID INSULATION) |
- |
0 |
|
- |
| 30(RESISTANCE TO HEAT AND FIRE) |
- |
0 |
|
- |
| 31(RESISTANCE TO RUSTING) |
- |
0 |
|
- |
| 19.11.4.3(Fast transient bursts) |
- |
45000 |
|
5% discount for BIS |
| 19.11.4.4(Surge immunity test) |
- |
45000 |
|
5% discount for BIS |
| 19.13(ABNORMAL OPERATION) |
- |
45000 |
|
5% discount for BIS |
| 19.101(Abnormal Operation) |
- |
45000 |
|
5% discount for BIS |
| 19.102(Abnormal Operation) |
- |
45000 |
|
5% discount for BIS |
|
19 Mar, 2029 |
-
Exclusion: 24 (COMPONENTS) |
| 9882 |
Delta Testing and Research Laboratories Private Limited (C5)
| 9179506
| IS 2016 (1967) |
Specification for plain washers (First Revision) |
All Grade / Type / Size / Designation |
5500 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 2.1(Material) |
- |
2000 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 2.2(Workmanship) |
- |
500 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 3(Designation) |
- |
500 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 4(Dimensions) |
- |
2000 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5(Finish) |
- |
1500 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7(Marking) |
- |
500 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
|
21 Aug, 2027 |
-
- |
| 9883 |
Delta Testing and Research Laboratories Private Limited (C5)
| 9179506
| IS 6649 (1985) |
Specification for hardened and tempered washers for high strength structural bolts and nuts (First Revision) |
All Grade / Type / Size / Designation |
10000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 3 Table-1(Dimensions Type A- d1) |
- |
2000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 3 Table-1(Dimensions Type A- d2) |
- |
2000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 3 Table-1(Dimensions Type A- S) |
- |
2000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 3 Table-2(Dimensions Type B&C- d) |
- |
2000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 3 Table-2(Dimensions Type B&C- a) |
- |
2000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 3 Table-2(Dimensions Type B&C- t) |
- |
2000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 3 Table-2(Dimensions Type B&C- θ) |
- |
2000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 3.1(Deviation) |
- |
2000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 3.2(Concentric) |
- |
2000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 3.3(Clearance) |
- |
2000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5(Chemical Composition- Sulphur) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5(Chemical Composition- Phosphorus) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7(Hardness) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8(Finish) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.1(Freedom from defect) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.1(Uniformity of zinc coating) |
- |
1500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.1(Mass of zinc coating) |
- |
1500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.1(Knife test (Adhesion of coating)) |
- |
1500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
|
21 Aug, 2027 |
-
- |
| 9884 |
Delta Testing and Research Laboratories Private Limited (C5)
| 9179506
| IS 9295 (1983) |
Specification for steel tubes for idlers for belt conveyors (First Revision) |
All Grade / Type / Size / Designation |
7500 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 7.1(Sulphur- Relevant Parts of IS 228 or any other established instrumental/chemical method) |
- |
500 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1(Phosphorous- Relevant Parts of IS 228 or any other established instrumental/chemical method) |
- |
500 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.1.1 Table 1(Tensile Strength- IS 1608(1)) |
- |
1250 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.1.1 Table 1(Yield Strength- IS 1608) |
- |
1250 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.1.1 Table 1(Elongation Percent- IS 1608) |
- |
1250 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.2(Drift Expansion Test- IS 2335) |
- |
1250 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.3(Flattening Test- IS 2328) |
- |
1000 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1 Table 2(Outside Diameter) |
- |
1000 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1 Table 2(Thickness) |
- |
1000 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1 Table 2(Mass) |
- |
1000 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 10(Hardness) |
- |
1000 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 13.1.1(Ovality) |
- |
1000 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 13.1.2(Eccentricity) |
- |
1000 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 15.1(Straightness) |
- |
1000 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 16.1(Length) |
- |
1000 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 17.1(Surface Protection) |
- |
1000 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 14.0(Workmanship) |
- |
500 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2(Fin height) |
- |
1000 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.1 Table 1 (ii)(Ends per dm) |
- |
1000 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.1 Table 1 (iii)(Picks per dm) |
- |
1000 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.1 Table 1 (iv)(Mass of fabric, g/m2) |
- |
1000 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.1 Table 1 (v)(Average breaking strength of fabric, Min [Raveled strip method, 200 mm × 50 mm1), N²) (kgf)]:
a) Length-wise
b) Width-wise) |
- |
1250 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.1 Table 1 (vi)(Minimum breaking strength of bottom seam (Strip method), N²) (kgf), Min) |
- |
1250 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.1 Table 1 (vii)(Elongation at break of fabric (Raveled strip method), percent :) |
- |
1250 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6(PRINTING, PACKING AND MARKING) |
- |
500 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
|
21 Aug, 2027 |
-
- |
| 9885 |
Delta Testing and Research Laboratories Private Limited (C5)
| 9179506
| IS 4948 (2020.0) |
Welded steel wire fabric for general use - Specification (Second Revision) |
All Grade / Type / Size / Designation |
5000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| Cl. 4.1(MATERIALS) |
- |
1500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 4.2(MATERIALS) |
- |
1500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 5.1(MANUFACTURE OF MESH (Assembling of Wires)) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 5.2(MANUFACTURE OF MESH) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 5.3(MANUFACTURE OF MESH) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 5.4(Spacing of Longitudinal and Transverse Wires) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 5.5(Tolerance of Size of Mesh) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 5.6(Tolerance of Size of Sheet or Roll) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 6(TEST FOR WELDING) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 9.1(Marking) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 9.1(Marking) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 9.1(Marking) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 9.1(Marking) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 9.1(Marking) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 9.1(Marking) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 9.1(Marking) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 9.3(BIS Certification Marking) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 10.1(Finish) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 4.1(MATERIALS) |
- |
1500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 4.2(MATERIALS) |
- |
1500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 5.1(MANUFACTURE OF MESH (Assembling of Wires)) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 5.2(MANUFACTURE OF MESH) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 5.3(MANUFACTURE OF MESH) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 5.4(Spacing of Longitudinal and Transverse Wires) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 5.5(Tolerance of Size of Mesh) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 5.6(Tolerance of Size of Sheet or Roll) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 6(TEST FOR WELDING) |
- |
3000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
|
21 Aug, 2027 |
-
- |
| 9886 |
Delta Testing and Research Laboratories Private Limited (C5)
| 9179506
| IS 937 (1981) |
Specification for Washers For Water Fittings For Fire Fighting Purposes |
All Grade / Type / Size / Designation |
5500 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 2.1(Hardness of Rubber before & after Ageing) |
- |
1250 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 2.1() |
- |
1250 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 2.1(Elongation at Break before & after Ageing) |
- |
1250 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 2.1(Acid & Alkali Resistant Test) |
- |
1250 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 4.1(Size & Dimension) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.1(Workmanship and Finish) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.1(Marking) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 2.2(Leather - IS 581) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
|
21 Aug, 2027 |
-
- |
| 9887 |
Delta Testing and Research Laboratories Private Limited (C5)
| 9179506
| IS 6528 (1995) |
Stainless steel wire - Specification (First Revision) |
All type of Grade / Type / Size / Designation |
11000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| Table 7(Workmanship) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 6(Workmanship) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 9.1 & Table 3(Diameter & Out Of Round) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 10(UTM) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Table 7(Workmanship) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 6(Workmanship) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 9.1 & Table 3(Diameter & Out Of Round) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Table 7(Workmanship) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 6(Workmanship) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 9.1 & Table 3(Diameter & Out Of Round) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 10(UTM) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Nitrogen) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Titanium) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Vanadium) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Boron) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Copper) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Molybdenum) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Nickel) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Chromium) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Aluminium) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Silicon) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Manganese) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Phosphorous) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Sulphor) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Carbon) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 10(UTM) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 9.1 & Table 3(Diameter & Out Of Round) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 6(Workmanship) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Table 7(Workmanship) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Table 7(Workmanship) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 6(Workmanship) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 9.1 & Table 3(Diameter & Out Of Round) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 10(UTM) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 10.2(Reverse bend test-IS 1716) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 10.3(Torsion test- IS 1717) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 10.4(Wrapping test-IS 1755) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 10.3(Torsion Test(IS 1717-1985)) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 15(Corrosion Resistance - IS:10461) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
|
21 Aug, 2027 |
-
- |
| 9888 |
Delta Testing and Research Laboratories Private Limited (C5)
| 9179506
| IS 3502 (2009) |
Steel chequered plates (Third Revision) |
All Grade / Type / Size / Designation |
7500 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| Cl 5(Workmanship) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 6(Workmanship) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 8(Tensile Test) |
- |
3500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 9(Press) |
- |
1500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 10(Length, Width, Thickness & Chequered Height) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 5(Workmanship) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 6(Workmanship) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 8(Tensile Test) |
- |
3500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 9(Press) |
- |
1500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 10(Length, Width, Thickness & Chequered Height) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 5(Workmanship) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 6(Workmanship) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 8(Tensile Test) |
- |
3500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 9(Press) |
- |
1500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 10(Length, Width, Thickness & Chequered Height) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 11(Weight) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 10(Thickness) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 10(Width) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl.8(Elongation) |
- |
1200 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl.8(Yield Stress) |
- |
1200 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 4.1(Grade E 250A of IS 2062.) |
- |
2500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 10(Length, Width, Thickness & Chequered Height) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 9(Press) |
- |
1500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 8(Tensile Test) |
- |
3500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 6(Workmanship) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 5(Workmanship) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl.4.1 (IS-2062, E250A)(CARBON) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl.4.1 (IS-2062, E250A)(SULPHUR) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl.4.1 (IS-2062, E250A)(PHOSPHURS) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl.4.1 (IS-2062, E250A)(MANGANESE) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl.4.1 (IS-2062, E250A)(SILICON) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl.4.1 (IS-2062, E250A)(CARBON EQUIVALENT) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl.4.1 (IS-2062, E250A)(NITROGEN) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 5(Workmanship) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 6(Workmanship) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 8(UTM) |
- |
3500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 9(Press) |
- |
1500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 10(Length, Width, Thickness & Chequered Height) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 4(Carbon as C) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 4(Manganese as Mn) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 4(Sulphur as S) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 4(Phosphorus as P) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 4(Silicon as Si) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 4(Aluminium as Al) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 4(Micro Alloying elements) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 4(Niobium as Nb) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 4(Vanadium as V) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 4(Titanium as Ti) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 4(Nitrogen content) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8(Tensile Strength-IS:1608(P1)-22) |
- |
1200 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8(Yield Stress-IS:1608(P1)-22) |
- |
1200 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8(Elongation on SoA 5.65mm GL) |
- |
1200 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 10(Length - SOP MT-23) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 10(Width - SOP MT-23) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 10(Thickness- SOP MT-23) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 10(Mass -SOP MT-23) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 10(Chequred Height - SOP MT-23) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 10(Chequred Height - SOP MT-23) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 4.1(Carbon- IS 228(Part 1)) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 4.1(Sulphur- IS 228(Part 9)) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 4.1(Phosphorous- IS 228(Part 3)) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 4.1(Manganese- IS 228(Part 2)) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 4.1(Carbon Equivalent (CE)) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 4.1(Silicon- IS 228(Part 2)) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 4.1(Nitrogen -IS 228(Part 19)) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
|
21 Aug, 2027 |
-
- |
| 9889 |
Alpha Test House Services LLP (160), Sahibzada Ajit Singh Nagar
| 9138706
| IS 362 (1991) |
Parliament Hinges -specification |
1,2,3 |
14000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| Cl. 7.1 (Brass parliament hinges shall have either bright or satin finish and shall be suitably protected against discoloration) |
- |
2000 |
|
- |
| Cl. 7.2 (Ref. Cl. 11.1 of IS 1868:1996)( appearance and Colour - shall be free from visible defects on the significant surface(s) when viewed from an agreed distance) |
- |
100 |
|
- |
| Cl. 7.2 (Ref. Cl.9 of IS 1868:1996)(Aluminium shall be anodized to a bright,
natural, sat or satin finish or dyed. ) |
- |
1500 |
|
- |
| Cl. 7.2 (Ref. Cl.9 of IS 1868:1996)(Anodinc casting thickness (Cl. 9.2 of IS 1868:1996)) |
- |
1500 |
|
- |
| Cl. 7.3(Mild steel parliament hinges shall be finished bright or electro-galvanized as specified by the purchaser) |
- |
1500 |
|
- |
| 3(Type) |
- |
200 |
|
- |
| 5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-Size) |
- |
200 |
|
- |
| 5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-A) |
- |
200 |
|
- |
| 5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-B) |
- |
200 |
|
- |
| 5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-C) |
- |
200 |
|
- |
| 5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-D) |
- |
200 |
|
- |
| 5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-d) |
- |
200 |
|
- |
| 5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-E) |
- |
200 |
|
- |
| 5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-Thickness of Flap) |
- |
200 |
|
- |
| 5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-No. of Screw holes) |
- |
200 |
|
- |
| 5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-Holes for screw designation) |
- |
200 |
|
- |
| 5.1-able 3(Dimensions for Cast Brass Parliament Hinges-Size) |
- |
200 |
|
- |
| 5.1-able 3(Dimensions for Cast Brass Parliament Hinges-A) |
- |
200 |
|
- |
| 5.1-able 3(Dimensions for Cast Brass Parliament Hinges-B) |
- |
200 |
|
- |
| 5.1-able 3(Dimensions for Cast Brass Parliament Hinges-C) |
- |
200 |
|
- |
| 5.1-able 3(Dimensions for Cast Brass Parliament Hinges-D) |
- |
200 |
|
- |
| 5.1-able 3(Dimensions for Cast Brass Parliament Hinges-d) |
- |
200 |
|
- |
| 5.1-able 3(Dimensions for Cast Brass Parliament Hinges-E) |
- |
200 |
|
- |
| 5.1-able 3(Dimensions for Cast Brass Parliament Hinges-Thickness of Flap) |
- |
200 |
|
- |
| 5.1-able 3(Dimensions for Cast Brass Parliament Hinges-No. of Screw holes) |
- |
200 |
|
- |
| 5.1-able 3(Dimensions for Cast Brass Parliament Hinges-Holes for screw designation) |
- |
200 |
|
- |
| 5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-Size) |
- |
200 |
|
- |
| 5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-A) |
- |
200 |
|
- |
| 5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-B) |
- |
200 |
|
- |
| 5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-C) |
- |
200 |
|
- |
| 5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-D) |
- |
200 |
|
- |
| 5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-d) |
- |
200 |
|
- |
| 5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-E) |
- |
200 |
|
- |
| 5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-Thickness of Flap) |
- |
200 |
|
- |
| 5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-No. of Screw holes) |
- |
200 |
|
- |
| 5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-Holes for screw designation) |
- |
200 |
|
- |
| 6.1(MANUFACTURE-General) |
- |
200 |
|
- |
| 6.1(MANUFACTURE-General) |
- |
200 |
|
- |
| 6.1(MANUFACTURE-General) |
- |
200 |
|
- |
| 6.2(MANUFACTURE-Knuckles) |
- |
200 |
|
- |
| 6.2(MANUFACTURE-Knuckles) |
- |
200 |
|
- |
| 6.2(MANUFACTURE-Knuckles) |
- |
200 |
|
- |
| 6.2(MANUFACTURE-Knuckles) |
- |
200 |
|
- |
| 6.3(MANUFACTURE-Pins) |
- |
200 |
|
- |
| 6.3(MANUFACTURE-Pins) |
- |
200 |
|
- |
| 6.3(MANUFACTURE-Pins) |
- |
200 |
|
- |
| 6.3(MANUFACTURE-Pins) |
- |
200 |
|
- |
| 6.4(MANUFACTURE-Screw Holes) |
- |
200 |
|
- |
| 6.5(MANUFACTURE-Position of Holes) |
- |
200 |
|
- |
| 6.5(MANUFACTURE-Position of Holes) |
- |
200 |
|
- |
| 6.5(MANUFACTURE-Position of Holes-minimum distance from
the ends of the flap) |
- |
200 |
|
- |
| 6.5(MANUFACTURE-Position of Holes-minimum distance from
the inner edge) |
- |
200 |
|
- |
| 6.5(MANUFACTURE-Position of Holes) |
- |
200 |
|
- |
| 7.1(FINISH) |
- |
200 |
|
- |
| 7.3(FINISH) |
- |
200 |
|
- |
|
- |
-
Included w.e.f. 03.04.2024 |
| 9890 |
Delta Testing and Research Laboratories Private Limited (C5)
| 9179506
| IS 4454 : Part 2 (2001) |
Steel wire for mechanical springs - Specification february 2001: Part 2 oil hardened and tempered steel wire (Second Revision) |
All type of Grade / Type / Size / Designation |
16000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| Cl 8(Workmanship) |
- |
100 |
|
10% Discount to BIS and for others 1.5 times of the mentioned testing charges. |
| Cl 9(Diameter & Difference Between Two Reading On Any Two Diameters) |
- |
100 |
|
10% Discount to BIS and for others 1.5 times of the mentioned testing charges. |
| Cl 10(Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test, Decarburization Test, Coating and Surface Finish & Eddy Current Test) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of the mentioned testing charges. |
| Cl 8(Workmanship) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of the mentioned testing charges. |
| Cl 9(Diameter & Difference Between Two Reading On Any Two Diameters) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of the mentioned testing charges. |
| Cl 10(Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test, Decarburization Test, Coating and Surface Finish & Eddy Current Test) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of the mentioned testing charges. |
| Cl 8(Workmanship) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of the mentioned testing charges. |
| Cl 9(Diameter & Difference Between Two Reading On Any Two Diameters) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of the mentioned testing charges. |
| Cl 10(Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test, Decarburization Test, Coating and Surface Finish & Eddy Current Test) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of the mentioned testing charges. |
| 7.1, 7.2(Vanadium) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of the mentioned testing charges. |
| 7.1, 7.2(Chromium) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of the mentioned testing charges. |
| 7.1, 7.2(copper) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of the mentioned testing charges. |
| 7.1, 7.2(phosphorus) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of the mentioned testing charges. |
| 7.1, 7.2(sulphur) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of the mentioned testing charges. |
| 7.1, 7.2(manganese) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of the mentioned testing charges. |
| 7.1, 7.2(silicon ) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of the mentioned testing charges. |
| 7.1, 7.2(carbon) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of the mentioned testing charges. |
| Cl 10(Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test, Decarburization Test, Coating and Surface Finish & Eddy Current Test) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of the mentioned testing charges. |
| Cl 9(Diameter & Difference Between Two Reading On Any Two Diameters) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of the mentioned testing charges. |
| Cl 8(Workmanship) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of the mentioned testing charges. |
| Cl 10(Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test, Decarburization Test, Coating and Surface Finish & Eddy Current Test) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of the mentioned testing charges. |
| Cl 9(Diameter & Difference Between Two Reading On Any Two Diameters) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of the mentioned testing charges. |
| Cl 8(Workmanship) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of the mentioned testing charges. |
| 8(Freedom from defects) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of the mentioned testing charges. |
| 11(Surface finish) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of the mentioned testing charges. |
| 15(Marking) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of the mentioned testing charges. |
|
21 Aug, 2027 |
-
Exclusion: Eddy Current Test as per Cl.10.8 (Optional test) |
| 9891 |
Alpha Test House Services LLP (160), Sahibzada Ajit Singh Nagar
| 9138706
| IS 453 (1993) |
Double Acting Spring Hinges -Specification |
MS,BRASS |
27000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 6(DIMENSIONS) |
- |
200 |
|
- |
| 9(PERFORMANCE TESTS) |
- |
12000 |
|
- |
| Clause 4.1(Mild Steel
Sheet) |
- |
1500 |
|
- |
| Clause 4.2(Mild Steel Wire) |
- |
1000 |
|
- |
| Clause 4.3(Cast Brass) |
- |
2000 |
|
- |
| Clause 4.4(Brass Sheets) |
- |
2000 |
|
- |
| Clause 4.5(Brass Rods) |
- |
2500 |
|
- |
| Clause 4.6(Steel Wire) |
- |
2100 |
|
- |
| Clause 4.7(Phosphor Bronze
Wire) |
- |
2100 |
|
- |
| Clause 5(Sizes) |
- |
200 |
|
- |
| Clause 6(Dimensions) |
- |
200 |
|
- |
| Clause 8(Finish) |
- |
200 |
|
- |
| Clause 9(Performance Test) |
- |
12000 |
|
- |
| Clause 10(Marking) |
- |
100 |
|
- |
| Clause 11(Packing) |
- |
100 |
|
- |
| Cl-7.1(Mild Steel Hinges) |
- |
200 |
|
- |
| Cl-7.1.1(Blank hinge shall be made from mild steel sheet) |
- |
200 |
|
- |
| Cl-7.2(Brass Hinges) |
- |
200 |
|
- |
| Cl-7.2.1(Blank hinges shall be made of cast brass) |
- |
200 |
|
- |
| 6(DIMENSIONS) |
- |
200 |
|
- |
| 9(PERFORMANCE TESTS) |
- |
12000 |
|
- |
| Clause 4.1(Mild Steel
Sheet) |
- |
1500 |
|
- |
| Clause 4.2(Mild Steel Wire) |
- |
1000 |
|
- |
| Clause 4.3(Cast Brass) |
- |
2000 |
|
- |
| Clause 4.4(Brass Sheets) |
- |
2000 |
|
- |
| Clause 4.5(Brass Rods) |
- |
2500 |
|
- |
| Clause 4.6(Steel Wire) |
- |
2100 |
|
- |
| Clause 4.7(Phosphor Bronze
Wire) |
- |
2100 |
|
- |
| Clause 5(Sizes) |
- |
200 |
|
- |
| Clause 6(Dimensions) |
- |
200 |
|
- |
| Clause 8(Finish) |
- |
200 |
|
- |
| Clause 9(Performance Test) |
- |
12000 |
|
- |
| Clause 10(Marking) |
- |
100 |
|
- |
| Clause 11(Packing) |
- |
100 |
|
- |
| Cl-7.1(Mild Steel Hinges) |
- |
200 |
|
- |
| Cl-7.1.1(Blank hinge shall be made from mild steel sheet) |
- |
200 |
|
- |
| Cl-7.2(Brass Hinges) |
- |
200 |
|
- |
| Cl-7.2.1(Blank hinges shall be made of cast brass) |
- |
200 |
|
- |
| 6(DIMENSIONS) |
- |
- |
|
- |
| 9(PERFORMANCE TESTS) |
- |
- |
|
- |
| Clause 4.1(Mild Steel
Sheet) |
- |
- |
|
- |
| Clause 4.2(Mild Steel Wire) |
- |
- |
|
- |
| Clause 4.3(Cast Brass) |
- |
- |
|
- |
| Clause 4.4(Brass Sheets) |
- |
- |
|
- |
| Clause 4.5(Brass Rods) |
- |
- |
|
- |
| Clause 4.6(Steel Wire) |
- |
- |
|
- |
| Clause 4.7(Phosphor Bronze
Wire) |
- |
- |
|
- |
| Clause 5(Sizes) |
- |
- |
|
- |
| Clause 6(Dimensions) |
- |
- |
|
- |
| Clause 8(Finish) |
- |
- |
|
- |
| Clause 9(Performance Test) |
- |
- |
|
- |
| Clause 10(Marking) |
- |
- |
|
- |
| Clause 11(Packing) |
- |
- |
|
- |
| Cl-7.1(Mild Steel Hinges) |
- |
- |
|
- |
| Cl-7.1.1(Blank hinge shall be made from mild steel sheet) |
- |
- |
|
- |
| Cl-7.2(Brass Hinges) |
- |
- |
|
- |
| Cl-7.2.1(Blank hinges shall be made of cast brass) |
- |
- |
|
- |
|
- |
-
Included w.e.f. 04.04.2024 |
| 9892 |
Delta Testing and Research Laboratories Private Limited (C5)
| 9179506
| IS 208 (2020) |
Door Handles - Specification ( Sixth Revision ) |
All Grade / Type / Size / Designation |
5000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 10(PACKING) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.1(BIS Certification Marking) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9(MARKING) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2(Tolerance) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.1 Table2A & 2B and Fig 1,2,3,4(DIMENSIONS - Size 1. No. in each Lug 2. No. in a plate when a continious plate is used 3. Size Designation of Counter-sunk Head Wood Screws (as per IS 6760: 1972)) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.1 Table2A & 2B and Fig 1,2,3,4(DIMENSIONS - Size (A,B,C,D,E,F,G,H,I)) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.1(MANUFACTURE- General) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 3(TYPES-Doors handle shall be of the following types according to the materials used:) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981)(Chemical composition - Zinc- IS 2600:1964) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981)(Chemical composition - Impurities-Nickel- IS 2600:1964) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981)(Chemical composition - Impurities-Thallium and Indium- IS 2600:1964) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981)(Chemical composition - Impurities-Tin- IS 2600:1964) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981)(Chemical composition - Impurities-Cadmium- IS 2600:1964) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl.5.1(General) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl.6(Dimension) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl.7(Finish) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl.8.2(Cossosion Test) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl.8.3(Quench Test) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl.9(Sampling and criterion for conformity) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl.10(Marking) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl.11(Packing) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
|
21 Aug, 2027 |
-
- |
| 9893 |
Delta Testing and Research Laboratories Private Limited (C5)
| 9179506
| IS 204 : Part 1 (1991) |
Tower bolts - Specification: Part 1 ferrous metals (Fifth Revision) |
All Grade / Type / Size / Designation |
3150 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 4 -Table 5- i (Ref. Cl 7, Table 3, HR1 grade of IS 1079 : 2017)(Chemical composition - Carbon - IS 228) |
- |
500 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 4 -Table 5- i (Ref. Cl 7, Table 3, HR1 grade of IS 1079 : 2017)(Chemical composition - Manganese - IS 228) |
- |
500 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 4 -Table 5- i (Ref. Cl 7, Table 3, HR1 grade of IS 1079 : 2017)(Chemical composition - Phosphorus - IS 228) |
- |
500 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 4 -Table 5- i (Ref. Cl 7, Table 3, HR1 grade of IS 1079 : 2017)(Chemical composition - Sulphur - IS 228) |
- |
500 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 4 -Table 5- ii (Ref. Cl 5, Table 1, E300-C grade of IS 2062 : 2011)(Chemical composition - Carbon - IS 228) |
- |
500 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 4 -Table 5- ii (Ref. Cl 5, Table 1, E300-C grade of IS 2062 : 2011)(Chemical composition - Manganese - IS 228) |
- |
500 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 4 -Table 5- ii (Ref. Cl 5, Table 1, E300-C grade of IS 2062 : 2011)(Chemical composition - Sulphur - IS 228) |
- |
500 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 4 -Table 5- ii (Ref. Cl 5, Table 1, E300-C grade of IS 2062 : 2011)(Chemical composition - Phosphorus - IS 228) |
- |
500 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 4 -Table 5- ii (Ref. Cl 5, Table 1, E300-C grade of IS 2062 : 2011)(Chemical composition - Silicon - IS 228) |
- |
500 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 4 -Table 5- ii (Ref. Cl 5, Table 1, E300-C grade of IS 2062 : 2011)(Chemical composition - Carbon Equivalen(CE) - IS 228) |
- |
500 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 4 -Table 5- iii (Ref. Cl 6.1 of IS 210 : 2009)(Chemical composition - Sulphur and/or Phosphorous) |
- |
500 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 4 -Table 5- iii (Ref. Cl 9.1 of IS 210 : 2009)(The microstructure shall be substantially free of primary cementite and/ or massive stead ite and shall consist oftlake graphite
in a matrix offerrite or pearlite or mixture thereof.) |
- |
1000 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 4 -Table 5- iii (Ref. Cl 9.1.1 of IS 210 : 2009)(Graphite structute Distribution - IS 7754) |
- |
1000 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.1(General) |
- |
500 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.2.1 Table 1(Particulars-Barrel Tower Bolts) |
- |
1000 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.2.2 Table 2(Particulars-Sami Barrel Tower Bolts) |
- |
1000 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.2.3 Table 3(Particulars-Riveted or Spot Welded Tower Bolts) |
- |
1000 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 5.2.4 Table 4(Particulars-Skeleton Tower Bolts) |
- |
1000 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.1- Table 1(Dimension of Barrel tower bolts-1.Size 2.Length of Bolt-A 3.Length of Barrel-B 4.Width of Barrel-C 5.Dia of Bolt-D 6.Length of Socket-E 7.Thickness of mild steel sheet for barrel-F 8.Dia of bore of barrel or socket- G ) |
- |
1000 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.1- Table 1(Dimension of Barrel tower bolts-Minimum No. of equally Spaced Screw holes in Barrel and Socket for wood screw no 6) |
- |
1000 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2- Table 2(Dimension of Sami Barrel Tower Bolts 1.Size 2.Length of Bolt-A 3.Length of Bolt Plate-B 4.Width of Bolt Plate-C 5.Dia of Bolt-D 6.Length of Socket-E 7.Thickness of Bolt Plate or Socket-F 8.Dia of bore of Bolt Plate or socket G ) |
- |
1000 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2- Table 2(Dimension of Sami Barrel Tower Bolts-Minimum No. of equally Spaced Screw holes in Bolt Plate and Socket for wood screw no 6) |
- |
1000 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.3- Table 3(Dimension of Riveted or Spot Welded Tower Bolts- 1.Size 2.Length of Bolt-A 3.Length of Bolt Plate-B 4.Width of Bolt Plate-C 5.Dia of Bolt-D 6.Length of Socket-E 7. Length of Strap-E" 8.Thickness of Back Plate -F 9.Thickness of Socket or Upper Plate and Strap- F" 10.Dia of bore of Bolt Plate or socket- G 11. Length of Alternative Socket-H ) |
- |
1000 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.3- Table 3(Dimension of Riveted or Spot Welded Tower Bolts-Minimum No. of equally Spaced Screw holes in Bolt Plate and Socket for wood screw no 6) |
- |
1000 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.4- Table 4(Dimension of Skeleton Tower Bolts 1.Size 2.Length of Bolt-A 3.Length of Bolt Plate-B 4.Width of Bolt Plate-C 5.Dia of Bolt-D 6.Length of Staple-E 7.Thickness of Plate or Staple -F 8.Dia of bore of Plate or Staple-G 9.Dia of shank of Knob-J) |
- |
1000 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.4- Table 4(Dimension of Skeleton Tower Bolts- Nos of Staples) |
- |
1000 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.4- Table 4(Dimension of Skeleton Tower Bolts-Minimum No. of Screw holes for wood screw no 6) |
- |
1000 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.1(MARKING- .) |
- |
500 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.1.1,(MARKING- ) |
- |
500 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9(PACKING) |
- |
500 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7(Finish) |
- |
1000 |
|
10 % Discount to BIS and for others 1.5 times of mentioned testing charges. |
|
21 Aug, 2027 |
-
- |
| 9894 |
The Synthetic and Art Silk Mills' Research Association (SASMIRA), MUMBAI
| 7175004
| IS 17730 : Part 2 (2021) |
Agro-Textiles Hail Protection Nets for Agriculture and Horticulture Purposes Specification Part 2 Woven Hail Protection Nets |
- |
15800 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| Clause 7, Table 1, (i)(Mass in g/m2, (with a tolerance of ± 5 percent)) |
- |
200 |
|
- |
| Clause 7, table 1, (ii) a("Average breaking strength of Woven hail
protection fabric (Strip method, 325 × 50 mm
test piece with gauge length of 200 mm), N,Min,(a) Warpway") |
- |
500 |
|
- |
| Clause 7,table 1, (ii) b("Average breaking strength of woven hail
protection fabric (Strip method, 325 × 50 mm
test piece with gauge length of 200 mm), N,Min,(b) Weftway") |
- |
0 |
|
- |
| Clause 7, table 1, (iii)("Retention of breaking strength after UV exposure
of 144 hours, percent, Min") |
- |
10500 |
|
- |
| Clause 7,table 1, (iv)(Colour fastness to artificial light (Applicable for coloured hail protection nets only)) |
- |
1200 |
|
- |
| Clause 7, table 1, (v)(Bursting pressure, kgf/cm2, Min) |
- |
400 |
|
- |
| Clause 7, table 1, (vi)(Shading percentage, percent, Max) |
- |
700 |
|
- |
| Clause 7, table 1, (vii)(Porosity, percent) |
- |
500 |
|
- |
| Clause 7, table 1, (viii)(Cold cracking resistance test at –10 °C) |
- |
700 |
|
- |
| Clause 7, table 1, (ix)(Seam (joint) strength, percent, Min) |
- |
700 |
|
- |
| Clause 7, Table 1, (i)(Mass in g/m2, (with a tolerance of ± 5 percent)) |
- |
0 |
|
the test has been charged for type 1. hence not repeated again for type 2. The sample will be charged irrespective of type 1 or type 2 with above quoted charges |
| Clause 7, table 1, (ii) a("Average breaking strength of Woven hail
protection fabric (Strip method, 325 × 50 mm
test piece with gauge length of 200 mm), N,Min,(a) Warpway") |
- |
0 |
|
the test has been charged for type 1. hence not repeated again for type 2. The sample will be charged irrespective of type 1 or type 2 with above quoted charges |
| Clause 7,table 1, (ii) b("Average breaking strength of woven hail
protection fabric (Strip method, 325 × 50 mm
test piece with gauge length of 200 mm), N,Min,(b) Weftway") |
- |
0 |
|
- |
| Clause 7, table 1, (iii)("Retention of breaking strength after UV exposure
of 144 hours, percent, Min") |
- |
0 |
|
the test has been charged for type 1. hence not repeated again for type 2. The sample will be charged irrespective of type 1 or type 2 with above quoted charges |
| Clause 7,table 1, (iv)(Colour fastness to artificial light (Applicable for coloured hail protection nets only)) |
- |
0 |
|
the test has been charged for type 1. hence not repeated again for type 2. The sample will be charged irrespective of type 1 or type 2 with above quoted charges |
| Clause 7, table 1, (v)(Bursting pressure, kgf/cm2, Min) |
- |
0 |
|
the test has been charged for type 1. hence not repeated again for type 2. The sample will be charged irrespective of type 1 or type 2 with above quoted charges |
| Clause 7, table 1, (vi)(Shading percentage, percent, Max) |
- |
0 |
|
the test has been charged for type 1. hence not repeated again for type 2. The sample will be charged irrespective of type 1 or type 2 with above quoted charges |
| Clause 7, table 1, (vii)(Porosity, percent) |
- |
0 |
|
the test has been charged for type 1. hence not repeated again for type 2. The sample will be charged irrespective of type 1 or type 2 with above quoted charges |
| Clause 7, table 1, (viii)(Cold cracking resistance test at –10 °C) |
- |
0 |
|
the test has been charged for type 1. hence not repeated again for type 2. The sample will be charged irrespective of type 1 or type 2 with above quoted charges |
| Clause 7, table 1, (ix)(Seam (joint) strength, percent, Min) |
- |
0 |
|
the test has been charged for type 1. hence not repeated again for type 2. The sample will be charged irrespective of type 1 or type 2 with above quoted charges |
| 7.1(Dimensions) |
- |
400 |
|
- |
|
14 Dec, 2026 |
-
- |
| 9895 |
The Synthetic and Art Silk Mills' Research Association (SASMIRA), MUMBAI
| 7175004
| IS 17730 : Part 1 (2021) |
Agro-Textiles Hail Protection Nets for Agriculture and Horticulture Purposes Specification Part 1 Warp Knitted Hail Protection Nets |
- |
17500 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| Clause 7, Table 1, (i)(Mass in g/m2, (with a tolerance of ± 5 percent)) |
- |
200 |
|
- |
| Clause 7, table 1, (ii) a("Average breaking strength of knitted hail
protection fabric (Strip method, 325 × 50 mm
test piece with gauge length of 200 mm), N,Min,(a) Wales direction") |
- |
500 |
|
- |
| Clause 7,table 1, (ii) b("Average breaking strength of knitted hail
protection fabric (Strip method, 325 × 50 mm
test piece with gauge length of 200 mm), N,Min,(b) Course direction") |
- |
0 |
|
- |
| Clause 7, table 1, (iii)("Retention of breaking strength after UV exposure
of 144 hours, percent, Min") |
- |
10500 |
|
- |
| Clause 7,table 1, (iv)(Colour fastness to artificial light (Applicable for coloured hail protection only)) |
- |
1200 |
|
- |
| Clause 7, table 1, (v)(Bursting pressure, kgf/cm2, Min) |
- |
400 |
|
- |
| Clause 7, table 1, (vi)(Shading percentage, percent, Max) |
- |
700 |
|
- |
| Clause 7, table 1, (vii)(Cold cracking resistance test at – 10 °C) |
- |
700 |
|
- |
| Clause 7, table 1, (viii)(Seam (joint) strength, percent, Min) |
- |
700 |
|
- |
| 4.1(HDPE Monofilament (linear density)) |
- |
400 |
|
- |
| 4.1.1(Heat shrinkage at 60 degree to 95 degree) |
- |
1000 |
|
- |
| 6.1(Fabric (width)) |
- |
200 |
|
- |
| 6.2(Reinforcement) |
- |
200 |
|
- |
| 6.4(Stitching) |
- |
200 |
|
- |
| 6.5(Colour) |
- |
200 |
|
- |
| 7.1(Length, Width) |
- |
400 |
|
- |
| 6.3(Joints) |
- |
0 |
|
- |
|
14 Dec, 2026 |
-
- |
| 9896 |
Delta Testing and Research Laboratories Private Limited (C5)
| 9179506
| IS 1239 : Part 1 (2004) |
Steel tubes, tubulars and other wrought steel fittings - Specification: Part 1 steel tubes (Sixth Revision) |
All Grade / Type / Size / Designation |
8400 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| Cl 8(Outer Diameter, Thickness & Mass) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 10.1(Manufacturing ) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 10.1.1(Manufacturing ) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 12(Workmanship) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 14(Tensile Test, Flattening Test & Bend Test) |
- |
2500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 15(Workmanship) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 8(Outer Diameter, Thickness & Mass) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 10.1(Manufacturing ) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 10.1.1(Manufacturing ) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 12(Workmanship) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 14(Tensile Test, Flattening Test & Bend Test) |
- |
2500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 15(Workmanship) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 8(Outer Diameter, Thickness & Mass) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 10.1(Manufacturing ) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 10.1.1(Manufacturing ) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 12(Workmanship) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 14(Tensile Test, Flattening Test & Bend Test) |
- |
2500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 15(Workmanship) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7, 6.1.1(CARBON) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7, 6.1.1(SULPHUR) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7, 6.1.1(PHOSPHURS) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7, 6.1.1(MANGANESE) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7, 6.1.1(NITROGEN) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7, 6.1.1(SILICON) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7, 6.1.1(ALUMINIUM) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 8(Outer Diameter, Thickness & Mass) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 10.1(Manufacturing) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 10.1.1(Manufacturing) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 12(Workmanship) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 14(Tensile Test, Flattening Test & Bend Test) |
- |
2500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 15(Workmanship) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Clause 8.1 (Table3,4,5)(Nominal Bore) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Clause 11.1(Random Length) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Clause 11.2(Exact Length) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Clause 11.3(Approximate Length) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Clause 14.1.1(Elongation Percent) |
- |
2500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 8 Table 3,4 & 5(Outside Diameter) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 8, 9 Table 3,4 & 5(Thickness) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 6.5(Height of Internal Fin) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 8, 9 Table 3,4 & 5(Mass of Tube) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 11(Length) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 3.3, 10.2(Plain End) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 14.1(Tensile Strength) |
- |
2500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 14.1.1(Elongation) |
- |
2500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 14.2(Bend Test (uto and including 50 mm NB)) |
- |
2500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 14.3(Flattening test (Over 50 mm NB)) |
- |
2500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 15(Workmanship) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 6.1.1, table1 of IS 1239(Part1)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 6.1.1, table1 of IS 1239(Part1)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 6.1.1, table1 of IS 1239(Part1)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl. 6.1.1, table1 of IS 1239(Part1)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.1.1(CARBON) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.1.1(SULPHUR) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.1.1(PHOSPHORUS) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.1.1(MANGANESE) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2 AND AS PER IS 10748(CARBON) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2 AND AS PER IS 10748(SULPHUR) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2 AND AS PER IS 10748(PHOSPHORUS) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2 AND AS PER IS 10748(MANGANESE) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2 AND AS PER IS 10748(CARBON EQUIVALENT) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2 AND AS PER IS 10748(SILICON) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2 AND AS PER IS 10748(ALUMINIUM) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2 AND AS PER IS 10748(MICRO ALLOY) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| STEEI-I TUBES, TUBULARS AND OTHER WROUGHT STEEL FITTINGS(NITROGEN) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2 AND AS PER IS 10748(COPPER) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2 AND AS PER IS 513(CARBON) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2 AND AS PER IS 513(SULPHUR) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2 AND AS PER IS 513(PHOSPHORUS) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2 AND AS PER IS 513(MANGANESE) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2 AND AS PER IS 513(SILICON) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2 AND AS PER IS 513(ALUMINIUM) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2 AND AS PER IS 513(MICRO ALLOY) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2 AND AS PER IS 513(NITROGEN) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 12 AND AS PER IS 4736(MASS OF ZINC COATING) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 12 AND AS PER IS 4736(UNIFORMITY OF ZINC COATING) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Clause - 6.1.1, Table-1(CARBON) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Clause - 6.1.1, Table-1(SULPHUR) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Clause - 6.1.1, Table-1(PHOSPHURS) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Clause - 6.1.1, Table-1(MANGANESE) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Clause - 6.1.1, Table-1(NITROGEN) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Clause - 6.1.1, Table-1(SILICON) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Clause - 6.1.1, Table-1(ALUMINIUM) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2 AND AS PER IS 10748(CARBON) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2 AND AS PER IS 10748(SULPHUR) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2 AND AS PER IS 10748(PHOSPHORUS) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2 AND AS PER IS 10748(MANGANESE) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2 AND AS PER IS 10748(CARBON EQUIVALENT) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2 AND AS PER IS 10748(SILICON) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2 AND AS PER IS 10748(ALUMINIUM) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2 AND AS PER IS 10748(MICRO ALLOY) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2 AND AS PER IS 10748(NITROGEN) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2 AND AS PER IS 10748(COPPER) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2 AND AS PER IS 513(CARBON) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2 AND AS PER IS 513(SULPHUR) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2 AND AS PER IS 513(PHOSPHORUS) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2 AND AS PER IS 513(MANGANESE) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2 AND AS PER IS 513(SILICON) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2 AND AS PER IS 513(ALUMINIUM) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2 AND AS PER IS 513(ALUMINIUM) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2 AND AS PER IS 513(MICRO ALLOY) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6.2 AND AS PER IS 513(NITROGEN) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 12 AND AS PER IS 4736(UNIFORMITY OF ZINC COATING) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.0 (b)(Thickness- SOP MT-23) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8.0 (c)(Mass of Tube- SOP MT-23) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 12.1(Galvanizing) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 12.2(Galvanizing) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 17.0 & 17.1(Marking -IS:1239 (P1)) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 17.0 & 17.2(Colour Band - IS:1239 (P1)) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 17.0 & 17.4(Length of colour band - IS:1239 (P1)) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 10.1(Thared Joints(IS:554)) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 10.2(Plain end) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 13.0(Leak Proof Test) |
- |
5000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 11(Length & tolerance) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 14.2 & 14.3(Bend/Flattening test) |
- |
2500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 15(Workmanship) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
|
21 Aug, 2027 |
-
- |
| 9897 |
Hindustaan Testing Solutions LLP, Ambala
| 9122136
| IS 13714 (1993) |
Dunnage pallets - Warehousing - Specification |
All |
5000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 4.1(DIMENSIONS) |
- |
400 |
|
Testing charges-5000
20% discount to BIS
GSTIN applicable as per govt rule |
| 4.1(DIMENSIONS) |
- |
0 |
|
- |
| 4.1(DIMENSIONS) |
- |
0 |
|
- |
| 5.1 Annex A(Timber) |
- |
0 |
|
- |
| 5.1.1(Timber) |
- |
100 |
|
- |
| 5.1.2(Timber) |
- |
1200 |
|
- |
| 5.1.2(Timber) |
- |
100 |
|
- |
| 5.1.2(Timber) |
- |
200 |
|
- |
| 5.1.2.1 (Objectionable knots) |
- |
200 |
|
- |
| 5.2.1(Nails) |
- |
100 |
|
- |
| 5.2.1(Nails) |
- |
100 |
|
- |
| 6.1 , Fig. 1(CONSTRUCTION) |
- |
400 |
|
- |
| 6.1.1(CONSTRUCTION) |
- |
400 |
|
- |
| 6.1.2(CONSTRUCTION) |
- |
400 |
|
- |
| 6.1.2(CONSTRUCTION) |
- |
400 |
|
- |
| 6.1.2(CONSTRUCTION) |
- |
400 |
|
- |
| 7(WORKMANSHIP AND FINISH) |
- |
400 |
|
- |
| 10.1 (a)(MARKING) |
- |
0 |
|
- |
| 10.1 (b)(MARKING) |
- |
0 |
|
- |
| 10.1 (c)(MARKING) |
- |
0 |
|
- |
| 5.1.2.1 (Objectionable knots) |
- |
200 |
|
- |
|
12 Sep, 2028 |
-
Included w.e.f. 09.05.2024
Exclusion: Identification of timber species & Cl.5.2 (Nails) |
| 9898 |
Delta Testing and Research Laboratories Private Limited (C5)
| 9179506
| IS 4454 : Part 1 (2001) |
Steel wire for mechanical springs - Specification: Part 1 cold drawn unalloyed steel wire (Third Revision) |
All type of Grade/Type/Size/Designation |
12000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| Cl 8(Workmanship) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 9(Diameter & Difference Between Two Reading On Any Two Diameters) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 10(Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test & Decarburization Test) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 8(Workmanship) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 9(Diameter & Difference Between Two Reading On Any Two Diameters) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 10(Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test & Decarburization Test) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(copper) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(Vanadium) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(phosphorus) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(sulphur) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(manganese) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(silicon ) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(carbon) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(copper) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(Chromium) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(phosphorus) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(sulphur) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(manganese) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(silicon ) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(carbon) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(copper) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(Chromium) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(phosphorus) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(sulphur) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(manganese) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(silicon ) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(carbon) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(copper) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(Vanadium) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(Chromium) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(phosphorus) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(sulphur) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(manganese) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(silicon ) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(carbon) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(copper) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(Vanadium) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(Chromium) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(phosphorus) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(sulphur) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(manganese) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(silicon ) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(carbon) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(copper) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(Vanadium) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(Chromium) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(phosphorus) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(sulphur) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(manganese) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(silicon ) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(carbon) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(copper) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(Vanadium) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(Chromium) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(phosphorus) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(sulphur) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(manganese) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(silicon ) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(carbon) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(copper) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(Vanadium) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(Chromium) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(phosphorus) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(sulphur) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(manganese) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(silicon ) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(carbon) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(copper) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(Vanadium) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(Chromium) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(phosphorus) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(sulphur) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(manganese) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(silicon ) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(carbon) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(copper) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(phosphorus) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(sulphur) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(manganese) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(silicon ) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(carbon) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(copper) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(phosphorus) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(sulphur) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(manganese) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(silicon ) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(carbon) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(copper) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(phosphorus) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(sulphur) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(manganese) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(silicon ) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(carbon) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(nitrogen) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(micro alloy) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(cu + cr+ni) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(sulphur + phosphorus) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(copper) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(phosphorus) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(sulphur) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(manganese) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(silicon ) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(carbon) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(cu + cr + ni) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(sulphur + phosphorus) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(copper) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(phosphorus) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(sulphur) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(manganese) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(silicon ) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7.1, 7.2(carbon) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 10(Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test & Decarburization Test) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 9(Diameter & Difference Between Two Reading On Any Two Diameters) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 8(Workmanship) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 10(Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test & Decarburization Test) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 9(Diameter & Difference Between Two Reading On Any Two Diameters) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 8(Workmanship) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 11(Coating and surface finish) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 11(Coating & Surface finish) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 15(Marking) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8(Freedom from defects) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 11(Surface finish) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 15(Marking) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 11(Coating & Surface finish) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 15(Marking) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 10(Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test & Decarburization Test) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 8(Workmanship) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| Cl 9(Diameter & Difference Between Two Reading On Any Two Diameters) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
|
21 Aug, 2027 |
-
- |
| 9899 |
Delta Testing and Research Laboratories Private Limited (C5)
| 9179506
| IS 1566 (1982) |
Specification for hard - Drawn steel wire fabric for concrete reinforcement (Second Revision) |
All Grade / Type / Size / Designation |
8500 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 4.1(Sulphur-Relevant Parts of IS 228) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 4.1(Phosphorous-Relevant Parts of IS 228) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 4.1(Nitrogen-Relevant Parts of IS 228) |
- |
500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 6(DIMENSIONS) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 7(SIZES OF SHEETS ‘OR ROLLS) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 8(MASS) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.2(Tolerance on Size of Mesh) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.3(Tolerance on Size of Sheet) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 9.4(Tolerance on Mass of Fabric) |
- |
1000 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 10(MECHANICAL PROPERTIES) |
- |
3500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 11.2(Tensile Test) |
- |
3500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
| 11.3(Reverse Bend Test) |
- |
1500 |
|
10% Discount to BIS and for others 1.5 times of mentioned testing charges. |
|
21 Aug, 2027 |
-
- |
| 9900 |
Alpha Test House Services LLP (160), Sahibzada Ajit Singh Nagar
| 9138706
| IS 3818 (1992) |
Continuous (Piano) hinges -Specification |
Type 1,2,3 & 4 |
5900 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| Cl. 6 (Ref. Cl.9 of IS 1868:1996)(Anodic casting thickness (Cl. 9.2 of IS 1868:1996)) |
- |
1000 |
|
- |
| 4-Fig 1(DIMENSIONS AND TOLERANCES-Nominal Size) |
- |
200 |
|
- |
| 4-Fig 1(DIMENSIONS AND TOLERANCES-B) |
- |
200 |
|
- |
| 4-Fig 1(DIMENSIONS AND TOLERANCES-C) |
- |
200 |
|
- |
| 4-Fig 1(DIMENSIONS AND TOLERANCES-D) |
- |
200 |
|
- |
| 4-Fig 1(DIMENSIONS AND TOLERANCES-T) |
- |
200 |
|
- |
| 4-Fig 1(DIMENSIONS AND TOLERANCES-CSK Screw No.) |
- |
200 |
|
- |
| 4-Fig 1(DIMENSIONS AND TOLERANCES-minimum distance of screw holes from the end of flap) |
- |
200 |
|
- |
| 4-Fig 1(DIMENSIONS AND TOLERANCES- Other Dimensions) |
- |
200 |
|
- |
| 4-Fig 2(DIMENSIONS AND TOLERANCES-CoNTINUOUS ( PIANO) HINGIS TYPB III; 50 min NOMINAL SID) |
- |
200 |
|
- |
| 4-Fig 3(DIMENSIONS AND TOLERANCES-B) |
- |
200 |
|
- |
| 4-Fig 3(DIMENSIONS AND TOLERANCES-B1) |
- |
200 |
|
- |
| 4-Fig 3(DIMENSIONS AND TOLERANCES-B2) |
- |
200 |
|
- |
| 4-Fig 3(DIMENSIONS AND TOLERANCES-C) |
- |
200 |
|
- |
| 4-Fig 3(DIMENSIONS AND TOLERANCES-D) |
- |
200 |
|
- |
| 4-Fig 3(DIMENSIONS AND TOLERANCES-T) |
- |
200 |
|
- |
| 4-Fig 3(DIMENSIONS AND TOLERANCES-CSK Screw No.) |
- |
200 |
|
- |
| 5.1(MANUFACTURE) |
- |
100 |
|
- |
| 5.2(MANUFACTURE-Knuekles) |
- |
100 |
|
- |
| 5.2(MANUFACTURE-Knuekles) |
- |
100 |
|
- |
| 5.3(MANUFACTURE-Pins) |
- |
100 |
|
- |
| 5.3(MANUFACTURE-Pins) |
- |
100 |
|
- |
| 5.3(MANUFACTURE-Pin-Anodized thickness) |
- |
1000 |
|
- |
| 5.3(MANUFACTURE-Pins) |
- |
100 |
|
- |
| 5.4(MANUFACTURE-Screw Holes) |
- |
100 |
|
- |
| 6(Finish) |
- |
1000 |
|
- |
|
- |
-
Included w.e.f. 03.04.2024 |
