| 9901 |
Baroda Calibration Services LLP, Vadodara
| 7175421
| IS 1180 : Part 1 (2014) |
Outdoor Type Oil Immersed Distribution Transformers Upto and Including 2 500 kVA, 33kV - Specification Part 1 Mineral Oil Immersed (Fourth Revision) |
Up to 2500 kVA, 33 kV, oil cooled, 1 Phase & 3 Phase |
125250 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 21.2 a)(Measurement of winding resistance ) |
- |
500 |
|
Test charges are for one Tap. Test charges for subsequent tap Rs. 400 |
| 21.2 b)( Measurement of voltage ratio and check of
phase displacemen) |
- |
650 |
|
Test charges are for one Tap. Test charges for subsequent tap Rs. 400 |
| 21.2 c)( Measurement of short-circuit impedance
(principal tapping, when applicable) and load
loss at 50 percent and 100 percent load) |
- |
3000 |
|
Test charges for subsequent tap Rs. 2200 |
| 21.2 d)(Measurement of no-load loss and current) |
- |
2100 |
|
Test charges for subsequent tap Rs. 1050 |
| 21.2 e)(Measurement of insulation resistance) |
- |
475 |
|
Test charges are for one Tap. Test charges for subsequent tap Rs. 475 |
| 21.2 f)(Induced over-voltage withstand test) |
- |
950 |
|
Test charges are for one Tap. Test charges for subsequent tap Rs. 950. |
| 21.2 g)( Separate-source voltage withstand test) |
- |
950 |
|
Test charges are for one Tap. Test charges for subsequent tap Rs. 950 |
| 21.5.3.3(Oil leakage test) |
- |
4250 |
|
- |
| 21.3(a )(Lightning impulse test) |
- |
30000 |
|
Charges given for above 250 KVA to 1000 KVA. so test charges vary by rating of transformer |
| 21.3(b)(Temperature-rise test) |
- |
15000 |
|
- |
| 21.4 c(No load current at 112.5 percent voltage.) |
- |
1400 |
|
Test charges are for one Tap. Test charges for subsequent tap Rs. 700 |
| 21.4 d(Paint adhesion tests) |
- |
1000 |
|
- |
| 7.8 (50%)(Total losses at 50 % load (Watts)) |
- |
1200 |
|
- |
| 7.8 (100%)(Total losses at 100 % load (Watts)) |
- |
1200 |
|
- |
| 21.5.1.1(Pressure test-Type test (For Transformers up to 200 kVA
)) |
- |
5000 |
|
- |
| 21.5.1.2(Pressure test-routine test (For Transformers up to 200 kVA
)) |
- |
5000 |
|
- |
| 21.5.2.1(Type test : For Transformers Above 200 kVA and Up to Including 2 500 kVA) |
- |
5000 |
|
- |
| 21.5.2.2(routine test :For Transformers Above 200 kVA and Up to Including 2 500 kVA) |
- |
5000 |
|
- |
| 21.5.3.1(For Single Phase Distribution Transformers Up to Including 25 kVA : pressure test (type test)) |
- |
5000 |
|
- |
| 21.5.3.2(For Single Phase Distribution Transformers Up to Including 25 kVA : pressure test (routine test)) |
- |
5000 |
|
- |
|
21 Dec, 2026 |
-
Exclusion: Cl.21.3(c) (Short-circuit withstand test), Cl.21.4 a) ( Determination of sound levels), Cl.21.4 e (BDV and moisture content of oil in the transformer), Cl.21.4 b (Short-circuit withstand test IS 2026 (Part 5) (above 200 kVA)) |
| 9902 |
PIONEER TESTING LABORATORY PRIVATE LIMITED
| 8176806
| IS 278 (2009) |
Galvanized steel barbed wire for fencing - Specification (Fourth Revision) |
All Type |
5850 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 4(Type A/Type B) |
- |
200 |
|
- |
| 5 Table-1(Sizes Diameter of Line wire) |
- |
300 |
|
- |
| 5 Table-1(Sizes Diamater of Point wire) |
- |
300 |
|
- |
| 5 Table-1(Sizes Mass of Completed barbed wire) |
- |
300 |
|
- |
| 5 Table-1(Sizes No. of Lays between the two consequtive barbs) |
- |
300 |
|
- |
| 9.1(Freedom from defects) |
- |
300 |
|
- |
| 9.2(Freedom from defects) |
- |
300 |
|
- |
| 12.1(Tensile Strength) |
- |
1000 |
|
- |
| 12.1(Breaking load) |
- |
1000 |
|
- |
| 12.2.1(Mass of zinc coating (line wire)) |
- |
1200 |
|
- |
| 12.2.2(Mass of zinc coating (point wire)) |
- |
1200 |
|
- |
| 12.2(Uniformity of zinc coating) |
- |
1200 |
|
- |
| 12.3(Ductility) |
- |
600 |
|
- |
| Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.) |
- |
300 |
|
- |
| Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.) |
- |
300 |
|
- |
| Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.) |
- |
300 |
|
- |
| Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.) |
- |
300 |
|
- |
| Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.) |
- |
300 |
|
- |
| Cl. 7.2(Cut Angle) |
- |
350 |
|
- |
| Cl. 7.2(Length of Barbs) |
- |
350 |
|
- |
| Cl. 7.1(General) |
- |
350 |
|
- |
|
10 Mar, 2027 |
-
- |
| 9903 |
BIS, Central Laboratory (CL)
| None
| IS 15844 : Part 2 (2023) |
SPORTS FOOTWEAR PART -2 PERFORMANCE SPORTS FOOTWEAR |
- |
20400 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 7.1.6 (Complete Shoe Flexing) |
- |
|
|
|
| 7.2 , Table No. 2 , iv) ,a) (Water vapour permeability) |
- |
|
|
|
| 7.2 , Table No. 2 , iv) ,b) (Water vapour coefficient) |
- |
|
|
|
| 7.2 , Table No. 2 , vii) (Tensile strength) |
- |
|
|
|
| 7.2 , Table No. 2 , viii) (Elongation at break,) |
- |
|
|
|
| 7.2 , Table No. 2 , x) (Abrasion test (for unlined upper)) |
- |
|
|
|
| 7.12, Table no. 1 of IS 17011,(x) (pH) |
- |
|
|
|
| 7.12, Table no. 1 of IS 17011,(xi) (Phthalates (each individual phthalate)) |
- |
|
|
|
| 7.12, Table no. 1 of IS 17011,(vii) (Formaldehyde) |
- |
|
|
|
| 7.12, Table no. 1 of IS 17011,(i) (Allergenic and carcinogenic disperse dyes) |
- |
|
|
|
| 7.12, Table no. 1 of IS 17011,(ii) (Aromatic amines released from Azo dyes (each individual amine)) |
- |
|
|
|
| 7.12, Table no. 1 of IS 17011,(iv) (Chromium (VI)) |
- |
|
|
|
| 7.12, Table no. 1 of IS 17011,(v) (Dimethyl fumarate (DMFU)) |
- |
|
|
|
| 7.12, Table no. 1 of IS 17011,(vi) (Formaldehyde (free or released by partial hydrolysis)) |
- |
|
|
|
| 7.12, Table no. 1 of IS 17011,(viii) (Organotin compounds) |
- |
|
|
|
| 7.12, Table no. 1 of IS 17011,(ix) (PCP-TeCP-TriCP polychlorophenols) |
- |
|
|
|
| 7.12, Table no. 1 of IS 17011,(xii) (Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB)) |
- |
|
|
|
| 7.12.2 (Amendment 1) (Lead content) |
- |
|
|
|
| 7.12 ("Chemical Requirement on Complete Product
for All Types of Sports Shoe") |
- |
|
|
|
|
- |
-
Complete for Chemical requirement as per IS 17011 (Innocuousness ), {The material composition of each shoe part must be clearly declared for testing, Testing willonly be conducted on the components that have been specified in the declaration on the Test request}
Mechanical (Partial) Except : i) Energy absorption at seat region cl 7.1.5, ii) Washability cl 7.1.7, iii) Colour fastness rubbing table 2, iv) Colour fastness to light table 2, v) Strength at needle perforation table 3, , vi) Bursting strength table 3, vii) Colour fastness to rubbing table 4, viii) Colour fastness to perspiration table 4, ix) Elastic Tape cl 7.10, x) Fasteners cl 7.11,
material requirement :4 pair of complete footwear and raw material with required specifications as per ISs and For abrassion resistance to outsole raw material of 10 mm min |
| 9904 |
PIONEER TESTING LABORATORY PRIVATE LIMITED
| 8176806
| IS 407 (1981) |
Specification for brass tubes for general purposes (Third Revision) |
All Type |
10250 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 6/6.1(FREEDOM FROM DEFECTS) |
- |
500 |
|
- |
| 7/7.1 & 7.1.1(CONDITION) |
- |
500 |
|
- |
| 8/8.1 & 8.2(SIZES AND TOLERANCES-Mean Outside Dia) |
- |
200 |
|
- |
| 8/8.1 & 8.2(SIZES AND TOLERANCES-Mean Wall thickness) |
- |
200 |
|
- |
| 8/8.1 & 8.2(SIZES AND TOLERANCES-Length) |
- |
200 |
|
- |
| 9/9.1/Appendix A(PRESSURE TESTS-Hydraulic Test) |
- |
1500 |
|
- |
| 9/9.2(PRESSURE TESTS-Pneumatic Test) |
- |
1500 |
|
- |
| 10/10.1-Table 2(PHYSICAL TEST- Hardness (HV)-IS : 1501 (Part 1)) |
- |
1500 |
|
- |
| 10/10.2-Table 2(PHYSICAL TEST- Tensilt Test - IS : 2655) |
- |
1500 |
|
- |
| 10/10.3(PHYSICAL TEST- Drifting Test- (For tubes upto and Including 100 mm nom OD)) |
- |
1000 |
|
- |
| 10/10.4 (10.4.1)("PHYSICAL TEST-Flattening Test (For Tubes ≤ 2.5 mm Wall Thickness and
not Exceeding 100 mm Outside Diameter)") |
- |
750 |
|
- |
| 10/10.4 (10.4.2)(PHYSICAL TEST-Flattening Test (For Tubes ≥ 2.5 mm Wall Thickness and More Than 100 mm Outside Diameter)) |
- |
750 |
|
- |
| 10/10.5(PHYSICAL TEST- Double Bend TestDouble Bend Test ( For Round Tubes ≤ 2.5 mm Wall Thickness and Over 100 mm Outside Diameter )) |
- |
1200 |
|
- |
| 10/10.6(PHYSICAL TEST- Mercurous Nitrate Test- IS : 2305) |
- |
1000 |
|
- |
| 11/11.1(MARKING) |
- |
350 |
|
- |
| 5(Chemical Composition - IS 3685) |
- |
1800 |
|
- |
|
10 Mar, 2027 |
-
- |
| 9905 |
BIS, Central Laboratory (CL)
| None
| IS 15844 : Part 1 (2023) |
SPORTS FOOTWEAR PART -1 GENERAL PURPOSEFirst Revision |
- |
20400 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| Cl No.4.4 , Table No. 2 , i) , a) (Flexing resistance, Dry condition) |
- |
|
|
|
| Cl No.4.4 , Table No. 2 , i) , b) (Flexing resistance, Wet condition) |
- |
|
|
|
| Cl No.4.4 , Table No. 2 , iv) , a) (Water vapour permeability, mg/cm2h, Min) |
- |
|
|
|
| Cl No.4.4 , Table No. 2 , iv) , b) (Water vapour coefficient, mg/cm2 , Min) |
- |
|
|
|
| Cl No.4.10 , Table No. 8 , iii) (Moisture resistance, percent, Min) |
- |
|
|
|
| Cl No . 4.14, Table no. 1 of IS 17011(x) (pH) |
- |
|
|
|
| Cl No . 4.14, Table no. 1 of IS 17011(xi) (Phthalates (each individual phthalate)) |
- |
|
|
|
| Cl No . 4.14, Table no. 1 of IS 17011(vii) (Formaldehyde) |
- |
|
|
|
| Cl No . 4.14, Table no. 1 of IS 17011(i) (Allergenic and carcinogenic disperse dyes) |
- |
|
|
|
| Cl No . 4.14, Table no. 1 of IS 17011(ii) (Aromatic amines released from Azo dyes (each individual amine)) |
- |
|
|
|
| Cl No . 4.14, Table no. 1 of IS 17011(iv) (Chromium (VI)) |
- |
|
|
|
| Cl No . 4.14, Table no. 1 of IS 17011(v) (Dimethyl fumarate (DMFU)) |
- |
|
|
|
| Cl No . 4.14, Table no. 1 of IS 17011(vi) (Formaldehyde (free or released by partial hydrolysis)) |
- |
|
|
|
| Cl No . 4.14, Table no. 1 of IS 17011(viii) (Organotin compounds) |
- |
|
|
|
| Cl No . 4.14, Table no. 1 of IS 17011(ix) (PCP-TeCP-TriCP polychlorophenols) |
- |
|
|
|
| Cl No . 4.14, Table no. 1 of IS 17011(x) (pH) |
- |
|
|
|
| Cl No . 4.14, Table no. 1 of IS 17011(xi) (Phthalates (each individual phthalate)) |
- |
|
|
|
| Cl No . 4.14, Table no. 1 of IS 17011(xii) (Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB)) |
- |
|
|
|
|
- |
-
Complete for Chemical ( The material composition of each shoe part must be clearly declared for testing)
Mechanical TF (Partial for Type 1);
Following test are not available:
i)Energy absorption at seat region Cl. 4.3.6 ii) Washability Cl. 4.3.8 (Optional) iii) Colour fastness to light (Optional) as per Table 1 iv) Bursting Strength, kg/cm2 , Min (Additional test required for Knitted Fabrics) as per Table 2 v) Colour fastness to perspiration(contact method) table 3 vi) Elastic Tape(limit of useful extension ) as per Table 10 / Lace tag strength as per Table 11 / Colour fastness to water of Table 11.
Complete Mechanical Test Facility for Type 2.
Sample Size requirement: 4 pairs of complete footwear and raw material with required specifications as per ISs and For abrasion resistance to the outsole, raw material of 10 mm min. thickness required. |
| 9906 |
BIS, Central Laboratory (CL)
| None
| IS 15844 (2010) |
Sports Footwear Specification |
- |
Single phase energy meters-Rs. 16179/- • Three phase en View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 3.7 (Tensile Strength) |
- |
|
|
|
| 3.8 (Elongation at Break ) |
- |
|
|
|
|
- |
-
No chemical testing
Excluding i) Energy absorption at seat region cl 3.3.4, ii) Lastometer test table 3, iii) Colour fastness & Fastness to artificial light, iv) Compression Set, v) Ross flaxing, vi) Flaxing index table 10, vii) Abrasion resistance of lace material table 14, viii) Counter material table 15 |
| 9907 |
PIONEER TESTING LABORATORY PRIVATE LIMITED
| 8176806
| IS 318 (1981) |
Specification for leaded tin bronze ingots and castings (Second Revision) |
All Type |
5800 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 7(SIZE AND SHAPE) |
- |
200 |
|
- |
| 6(FREEDOM FROM DEFECTS) |
- |
300 |
|
- |
| 3, Table 1.(CHEMlCAL COMPOSITION) |
- |
2600 |
|
- |
| 7.2(Dimension) |
- |
300 |
|
- |
| 7.1(Mass) |
- |
500 |
|
- |
| 6.2(Freedom from defects-Castings) |
- |
300 |
|
- |
| 6.1(Freedom from defects-Ingots) |
- |
300 |
|
- |
| 4.1, Table 2(Elongation) |
- |
1000 |
|
- |
| 4.1, Table 2(0.2% Proof stress) |
- |
1000 |
|
- |
| 4.1, Table 2(Tensile strength) |
- |
1000 |
|
- |
| 5(Pressure Test) |
- |
500 |
|
- |
| 8(Marking) |
- |
200 |
|
- |
|
10 Mar, 2027 |
-
- |
| 9908 |
PIONEER TESTING LABORATORY PRIVATE LIMITED
| 8176806
| IS 319 (2007) |
Free cutting brass bars, rods and section - Specification (Fifth Revision) |
All Type |
6500 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 5.0(Freedom from defects) |
- |
500 |
|
- |
| 7.0(Dimension and Tolerances) |
- |
500 |
|
- |
| 8.1 Table 1(Cu) |
- |
750 |
|
- |
| 8.1 Table 1(Pb) |
- |
750 |
|
- |
| 8.1 Table 1(Fe) |
- |
750 |
|
- |
| 8.1 Table 1(Total other impurities excluding iron) |
- |
750 |
|
- |
| 8.1 Table 1(Zn) |
- |
750 |
|
- |
| 9.1 Table-2(Tensile Strength) |
- |
1000 |
|
- |
| 9.1 Table-2(Elongation) |
- |
1000 |
|
- |
| 9.2(Vickers Hardness) |
- |
1500 |
|
- |
| 10.1(Mercurous Nitrate Test) |
- |
1500 |
|
- |
| 14(Marking) |
- |
300 |
|
- |
|
10 Mar, 2027 |
-
- |
| 9909 |
PIONEER TESTING LABORATORY PRIVATE LIMITED
| 8176806
| IS 1328 (1996) |
Veneered Decorative Plywood -Specification |
All Type |
3850 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 4.1(Grade - For BWR) |
- |
200 |
|
- |
| 4.1(Grade - For MR) |
- |
200 |
|
- |
| 4.2(Type - For Type 1) |
- |
200 |
|
- |
| 4.2(Type - For Type 2) |
- |
200 |
|
- |
| 7.1.1(Requirements - Open splits, checks or open joints - For Type 1 - Cl. 7.1.1) |
- |
200 |
|
- |
| 7.2.1(Requirements - Open splits, checks or open joints - For Type 2 - Cl. 7.2.1) |
- |
200 |
|
- |
| 7.1.2(Requirements - Other defects - For Type 1 - Cl. 7.1.2) |
- |
200 |
|
- |
| 7.2.2(Requirements - Other defects - For Type 2 - Cl. 7.2.2.) |
- |
200 |
|
- |
| 7.1.3(Requirements - Other Charcteristics and Manufacturing Defects - For Type 1 - Cl. 7.1.3) |
- |
200 |
|
- |
| 7.2.3(Requirements - Other Charcteristics and Manufacturing Defects - For Type 2 - Cl. 7.2.3) |
- |
200 |
|
- |
| 8(Dimensions & Tolerances - Length - Cl. 8) |
- |
400 |
|
- |
| 8(Dimensions & Tolerances - Width - Cl. 8) |
- |
400 |
|
- |
| 8(Dimensions & Tolerances - Thickness - Cl. 8) |
- |
400 |
|
- |
| 8(Dimensions & Tolerances - Edge Straightness - Annexure C) |
- |
1200 |
|
- |
| 8(Dimensions & Tolerances - Squareness - Annexure C) |
- |
1200 |
|
- |
| 9(Finish - Cl. 9.1, 8.3) |
- |
500 |
|
- |
| 11(Tests - Moisture Content - Part 1 of IS 1734) |
- |
1000 |
|
- |
| 11(Tests - Water Resistance Test - Cl. 11.1.2.2 [for BWR Grade]) |
- |
1500 |
|
- |
|
10 Mar, 2027 |
-
- |
| 9910 |
PIONEER TESTING LABORATORY PRIVATE LIMITED
| 8176806
| IS 694 (2010) |
Polyvinyl chloride insulated unsheathed and sheathed cables/cords with rigid and flexible conductor for rated voltages up to and including 450/750 v (Fourth Revision) |
All Type |
43750 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 13(Cable code) |
- |
200 |
|
- |
| 11.2(Legibility) |
- |
200 |
|
- |
| 11.1(Durability) |
- |
200 |
|
- |
| 11(Identification) |
- |
200 |
|
- |
| 10.9(Additional ageing test (OU cables only) -HV test (at 60±3oC)) |
- |
5500 |
|
- |
| 10.4(Flammability test- Unaffected portion) |
- |
3500 |
|
- |
| 10.4(Flammability test-Burning after flame removal) |
- |
3500 |
|
- |
| table 1 e) 3) (IR constant- max. Temp) |
- |
1200 |
|
- |
| table 1 e) 3) (IR constant- Room temp ) |
- |
1200 |
|
- |
| table 1 e) 3) (Volume Resistivity - Maximum temp) |
- |
1000 |
|
- |
| table 1 e) 3) (Volume Resistivity - Room temp ) |
- |
1000 |
|
- |
| 10.2(HV (room temperature)) |
- |
2500 |
|
- |
| 10.1(HV (water immersion)) |
- |
8000 |
|
- |
| 10.8(Smoke density rating) |
- |
2500 |
|
- |
| 10.6(Halogen evolution) |
- |
2000 |
|
- |
| 10.7(Temperature index) |
- |
2500 |
|
- |
| 10.5(Oxygen index) |
- |
2000 |
|
- |
| Table 1 iii) d) 9)(Cold impact for sheath) |
- |
1000 |
|
- |
| Table 1 iii) d) 8)(Cold bend for sheath) |
- |
1000 |
|
- |
| Table 1 iii) c) 9)(Cold impact for insulation) |
- |
1000 |
|
- |
| Table 1(Category Code) |
- |
200 |
|
- |
| Table 1 iii) d) 7)(Thermal stability- Sheath ) |
- |
1500 |
|
- |
| Table 1 iii) c) 7)(Thermal stability- Insulation ) |
- |
1500 |
|
- |
| Table 1 iii) d) 6)(Hot deformation -Indentation depth - Sheath ) |
- |
1500 |
|
- |
| Table 1 iii) c) 6)(Hot deformation - Indentation depth- Insulation) |
- |
1500 |
|
- |
| Table 1 iii) d) 5)(Heat shock-Sheath ) |
- |
1000 |
|
- |
| Table 1 iii) c) 5)(Heat shock-Insulation ) |
- |
1000 |
|
- |
| Table 1 iii) d) 4)(Cracks Observed) |
- |
1000 |
|
- |
| Table 1 iii) d) 4)(Shrinkage- Sheath ) |
- |
750 |
|
- |
| Table 1 iii) c) 4)(Shrinkage-Insulation) |
- |
750 |
|
- |
| Table 1 iii) d) 2)(Loss of mass- Sheath ) |
- |
750 |
|
- |
| Table 1 iii) c) 2)(Loss of mass- Insulation ) |
- |
750 |
|
- |
| Table 1 iii) d) 3)(Sheath- Elongation variation) |
- |
1200 |
|
- |
| Table 1 iii) d) 3)(Sheath- TS variation) |
- |
1200 |
|
- |
| Table 1 iii) d) 3)(Sheath- Elongation (After ageing)) |
- |
1200 |
|
- |
| Table 1 iii) d) 3)(Sheath- Tensile strength (After ageing)) |
- |
1200 |
|
- |
| Table 1 iii) d) 1)(Sheath- Elongation (Without ageing)) |
- |
1200 |
|
- |
| Table 1 iii) d) 1)(Sheath -Tensile strength (Without ageing)) |
- |
1200 |
|
- |
| Table 1 iii) c) 3)(Elongation variation) |
- |
1200 |
|
- |
| Table 1 iii) c) 3)(TS variation) |
- |
1200 |
|
- |
| Table 1 iii) c) 3)(Elongation (After ageing)) |
- |
1200 |
|
- |
| Table 1 iii) c) 3)(Tensile strength (After ageing)) |
- |
1200 |
|
- |
| Table 1 iii) c) 1)(Elongation (Without ageing)) |
- |
1200 |
|
- |
| Table 1 iii) c) 1)(Tensile strength (Without ageing)) |
- |
1200 |
|
- |
| (Cl. 18.1.4)
(Cl. 19.1.5)
(Cl. 20.1.4)
(Cl. 22.1.4)(Colour of Sheath) |
- |
200 |
|
- |
| 8.3(Thickness of Sheath) |
- |
350 |
|
- |
| 5.2(Application ) |
- |
200 |
|
- |
| 5.3(Thickness of Insulation) |
- |
200 |
|
- |
| 9.1(Ovality) |
- |
200 |
|
- |
| 9(Overall dimensions) |
- |
200 |
|
- |
| 10.11(Per sulphate test (for tinned Cu cable only)) |
- |
350 |
|
- |
| 4.2(Conductor resistance test) |
- |
2000 |
|
- |
| 4.1(Wrapping test (for Al)) |
- |
1000 |
|
- |
| 4.1(Tensile test (for Al)- After Stranding) |
- |
1200 |
|
- |
| 4.1(Tensile test (for Al)-Before Stranding) |
- |
1200 |
|
- |
| 4.1(Annealing test (for copper)) |
- |
1000 |
|
- |
| (Cl.6.1.3 of IS 8130:2013)(Flexible Conductors (Classes 5)) |
- |
1500 |
|
- |
| (Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors(Class-2)) |
- |
1500 |
|
- |
| (Cl.6.1.3 of IS 8130:2013)(Stranded compacted circular conductors and shaped conductors (Class 2)) |
- |
1500 |
|
- |
| (Cl.6.1.3 of IS 8130:2013)(Solid Conductor (Class 1)) |
- |
1500 |
|
- |
| (Cl.16.1)
(Cl.19.1)(Conductor- Diameter ) |
- |
1500 |
|
- |
| (Cl. 18.1.3)
(Cl. 19.1.4)
(Cl. 20.1.3)
(Cl. 21.1.3)
(Cl. 22.1.3)(Assembly of cores ) |
- |
500 |
|
- |
| 12(CONSTRUCTION Core Identification) |
- |
500 |
|
- |
| 8.1(Sheath Material ) |
- |
500 |
|
- |
| 7(Binder Tape) |
- |
500 |
|
- |
| 6.2(Filler) |
- |
500 |
|
- |
| 5.1(Insulation) |
- |
500 |
|
- |
| 4.4(Joints in Conductor) |
- |
500 |
|
- |
| 4.1(Conductor - Material) |
- |
500 |
|
- |
| 10.11(Persulphate Test ) |
- |
1500 |
|
- |
| 12.0(Core identification) |
- |
500 |
|
- |
| 4, IS 8130(Construction of conductor) |
- |
500 |
|
- |
| Table 2, IS 8130(No fo wire in a conductor) |
- |
200 |
|
- |
| 8.3(Minimum thickness of Sheath) |
- |
350 |
|
- |
| 8.3(Avarage thickness of Sheath) |
- |
200 |
|
- |
| 5.3(Avarage thickness of insulation) |
- |
200 |
|
- |
| Table 4(Copper purity test) |
- |
6500 |
|
- |
| 10.3(Spark test) |
- |
1500 |
|
- |
| table 1, 4.2(insulation resistance test) |
- |
1000 |
|
- |
| 5.4(Mechanical properties before and after ageing) |
- |
1500 |
|
- |
| 10.3(Spark Test) |
- |
1500 |
|
- |
| 22(TWO AND THREE CORE FLAT CABLES WITH PVC INSULATION
AND SHEATHED (CLASS 2 OR 5) FOR GENERAL PURPOSE( FOR MAXIMUM CONDUCTOR TEMPERA TURE 70°C OR 85°C)) |
- |
0 |
|
- |
| 21(ARALLEL TWIN AND TWISTED TWIN FLEXIBLE PVC INSULATED
UNSHEATHED CORDS (CLASS 5) FOR GENERAL PURPOSE (FOR MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C)) |
- |
0 |
|
- |
| 20(MULTICORE CIRCULAR PVC INSULATED AND SHEATHED
CABLES WITH FLEXIBLE CONDUCTOR (CLASS 5) FOR GENERAL PURPOSE (FOR MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C)) |
- |
0 |
|
- |
| 19(SINGLE AND MULTICORE CIRCULAR PVC INSULATED AND SHEATHED CABLES/CORDS WITH FLEXIBLE CONDUCTOR (CLASS 5)
FOR GENERAL PURPOSE (MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C)) |
- |
0 |
|
- |
| 18(SINGLE AND MULTICORE CIRCULAR PVC INSULATED
AND SHEATHED CABLES WITH RIGID CONDUCTOR (CLASS 1 AND CLASS 2) FOR GENERAL PURPOSE ) FOR MAXIMUM CONDUCTOR TEMPERATURE (70°C OR 85°C)) |
- |
0 |
|
- |
| 17(SINGLE CORE NON-SHEATHED CABLES WITH
FLEXIBLE CONDUCTOR FOR GENERAL PURPOSE (MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C)) |
- |
0 |
|
- |
| 16.2(Tests) |
- |
0 |
|
- |
| 16.1(Construction) |
- |
500 |
|
- |
| 15(PACKING AND MARKING) |
- |
500 |
|
- |
| 13(CABLE CODE) |
- |
200 |
|
- |
| 12(CORE IDENTIFICATION) |
- |
500 |
|
- |
| 10.11(Persulphate Test) |
- |
1500 |
|
- |
| 11(IDENTIFICATION) |
- |
0 |
|
- |
| 10.1(Flex Test) |
- |
0 |
|
- |
| 10.9(Additional Ageing Test (for Cables for Outdoor Use) |
- |
5500 |
|
- |
| 10.8(Smoke Density Rating) |
- |
2500 |
|
- |
| 10.7(Test for Temperature Index) |
- |
2500 |
|
- |
| 10.6(Test for Halogen Acid Gas Evolution) |
- |
2000 |
|
- |
| 10.5(Oxygen Index Test) |
- |
2000 |
|
- |
| 10.4(Flammability Test) |
- |
3500 |
|
- |
| 10.3(Spark Test) |
- |
1500 |
|
- |
| 10.2(High Voltage Test (at Room Temperature)) |
- |
4000 |
|
- |
| 10.1(High Voltage Test (Water Immersion Test)) |
- |
4000 |
|
- |
| 9(OVERALL DIMENSIONS) |
- |
200 |
|
- |
| 8(SHEATH) |
- |
200 |
|
- |
| 7(BINDER TAPE) |
- |
0 |
|
- |
| 6(FILLER) |
- |
0 |
|
- |
| 5(INSULATION) |
- |
0 |
|
- |
| 4.1(Material) |
- |
0 |
|
- |
| 4.2(Electrical Resistance) |
- |
2000 |
|
- |
| 5.3(Minimum thickness of insulation) |
- |
200 |
|
- |
| 4.1(Conductor - Material) |
- |
0 |
|
- |
| 4.4(Joints in Conductor) |
- |
0 |
|
- |
| 6.1(Filler) |
- |
0 |
|
- |
| (Cl.16.1)
(Cl.19.1)(Conductor) |
- |
0 |
|
- |
| (Cl.16.1)
(Cl.19.1)(Conductor) |
- |
0 |
|
- |
| (Cl.16.1)
(Cl.19.1)(Conductor) |
- |
0 |
|
- |
| (Cl.6.1 of IS 8130:2013)(Solid Conductor (Class 1)) |
- |
0 |
|
- |
| (Cl.6.1 of IS 8130:2013)(Solid Conductor (Class 1)) |
- |
0 |
|
- |
| (Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors (Class-2)) |
- |
0 |
|
- |
| (Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors (Class-2)) |
- |
0 |
|
- |
| (Cl.6.1.3 of IS 8130:2013)( Flexible Conductors (Classes 5)) |
- |
1500 |
|
- |
| Table 1 iii) c) 4)(Cracks Observed) |
- |
1000 |
|
- |
| Table 1 iii) c) 8)(Cold bend for insulation) |
- |
1000 |
|
- |
| 10.1(HV (water immersion)) |
- |
8000 |
|
- |
|
10 Mar, 2027 |
-
- |
| 9911 |
PIONEER TESTING LABORATORY PRIVATE LIMITED
| 8176806
| IS 1161 (2014) |
Steel tubes for structural purposes - Specification (Fifth Revision) |
All Type |
8400 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| Cl 6(Outer Diameter, Thickness & Mass) |
- |
800 |
|
- |
| Cl 7(Workmanship) |
- |
500 |
|
- |
| Cl 8(Workmanship) |
- |
1500 |
|
- |
| Cl 9(Workmanship) |
- |
1500 |
|
- |
| Cl 11(Tensile Test, Flattening Test & Cold Bend Test) |
- |
3500 |
|
- |
| Cl 13(Workmanship) |
- |
500 |
|
- |
| 8 AND AS PER IS 4736(UNIFORMITY OF ZINC COATING) |
- |
1500 |
|
- |
| 8 AND AS PER IS 4736(MASS OF ZINC COATING) |
- |
1500 |
|
- |
| 5 AND AS PER IS 10748(COPPER) |
- |
300 |
|
- |
| 5 AND AS PER IS 10748(MICRO ALLOY) |
- |
900 |
|
- |
| 5 AND AS PER IS 10748(CARBON EQUIVALENT) |
- |
300 |
|
- |
| 5 AND AS PER IS 10748(CARBON) |
- |
300 |
|
- |
| Clause - 5.1, Table-3( ALUMINIUM) |
- |
400 |
|
- |
| Clause - 5.1, Table-3(SILICON) |
- |
300 |
|
- |
| Clause - 5.1, Table-3(NITROGEN) |
- |
350 |
|
- |
| Clause - 5.1, Table-3(MANGANESE) |
- |
300 |
|
- |
| Clause - 5.1, Table-3(PHOSPHURS) |
- |
300 |
|
- |
| Clause - 5.1, Table-3(SULPHUR) |
- |
300 |
|
- |
| Clause - 5.1, Table-3( CARBON) |
- |
300 |
|
- |
| 9(Straightness) |
- |
500 |
|
- |
| 10(Lengths) |
- |
300 |
|
- |
| Cl 11.3.1(Flattening test (over 50 mm NB)) |
- |
750 |
|
- |
| Cl 11.3.1(Cold bend test (upto & including 50 mm NB)) |
- |
1000 |
|
- |
| Cl. 11.2 Table 2(Elongation) |
- |
750 |
|
- |
| Cl. 11.2 Table 2(Yield strength) |
- |
750 |
|
- |
| Cl. 6 , 6.2 Table 1(Square of radius of gyyration) |
- |
500 |
|
- |
| Cl. 6 , 6.2 Table 1(Radius of gyration) |
- |
500 |
|
- |
| Cl. 6 , 6.2 Table 1(Area of cross section) |
- |
500 |
|
- |
| Cl. 6 , 6.2 Table 1(Weight) |
- |
500 |
|
- |
| Cl 13(Workmanship) |
- |
500 |
|
- |
| 8.0(Freedom from defects - IS 4736) |
- |
500 |
|
- |
| 8.0(Adhesion test-Pivoted Hammer Test - IS 4736) |
- |
1500 |
|
- |
| 13.0(Oiling and Painting - Visual) |
- |
500 |
|
- |
|
10 Mar, 2027 |
-
- |
| 9912 |
PIONEER TESTING LABORATORY PRIVATE LIMITED
| 8176806
| IS 710 (2010) |
Marine plywood - Specification (Second Revision) |
All Type |
15450 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 11.1(MARKING) |
- |
250 |
|
- |
| 11.2(MARKING) |
- |
250 |
|
- |
| 7.1(WORKMANSHIP AND FINISH ) |
- |
500 |
|
- |
| 7.2(WORKMANSHIP AND FINISH ) |
- |
500 |
|
- |
| 7.3(WORKMANSHIP AND FINISH ) |
- |
500 |
|
- |
| 7.5(WORKMANSHIP AND FINISH ) |
- |
500 |
|
- |
| 6.1(DIMENSIONS) |
- |
750 |
|
- |
| 6.2(DIMENSIONS) |
- |
750 |
|
- |
| 6.3(DIMENSIONS) |
- |
750 |
|
- |
| 6.3(DIMENSIONS) |
- |
750 |
|
- |
| 9.1.1(MOISTURE CONTENT) |
- |
500 |
|
- |
| 9.1.2 , 9.1.2.1(Glue Adhesion in Dry State) |
- |
750 |
|
- |
| 9.1.2 , 9.1.2.2(Glue Adhesion in Dry State) |
- |
750 |
|
- |
| 9.1.3 , 9.1.3.1.1(Water resistance test) |
- |
1000 |
|
- |
| 9.1.3 , 9.1.3.1.2(Water resistance test) |
- |
1000 |
|
- |
| 9.1.5(Mycological test) |
- |
1000 |
|
- |
| 9.1.5 , 9.1.3.1.1(Mycological test) |
- |
1000 |
|
- |
| 9.1.5 , 9.1.3.1.2(Mycological test) |
- |
1000 |
|
- |
| 9.1.4(Tensile strength) |
- |
800 |
|
- |
| 9.1.6 (Table 3)(Static bending strength) |
- |
750 |
|
- |
| 9.1.6 (Table 3)(Static bending strength) |
- |
750 |
|
- |
| 9.1.7 (Table 4)(Wet bending strength) |
- |
1200 |
|
- |
| 9.1.7 (Table 4)(Wet bending strength) |
- |
1200 |
|
- |
| 9.1.8(Retention of preservative) |
- |
1500 |
|
- |
| Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Rupture: Across the Face Grain: Minimum Individual)) |
- |
750 |
|
- |
| Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Rupture: Across the Face Grain: Average)) |
- |
750 |
|
- |
| Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Rupture: Along the Face Grain: Minimum Individual)) |
- |
750 |
|
- |
| Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Rupture: Along the Face Grain: Average)) |
- |
750 |
|
- |
| Cl. 9.1.7 (Table 4)(Cl. 9.1.7 (Table 4) (Modulus of Elasticity: Across the Face Grain: Minimum Individual)) |
- |
750 |
|
- |
| Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Elasticity: Across the Face Grain: Average)) |
- |
750 |
|
- |
| Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Elasticity: Along the Face Grain: Minimum Individual)) |
- |
750 |
|
- |
| Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Elasticity: Along the Face Grain: Average)) |
- |
750 |
|
- |
| Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Rupture: Across the Face Grain: Minimum Individual)) |
- |
1200 |
|
- |
| Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Rupture: Across the Face Grain: Average)) |
- |
1200 |
|
- |
| Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Rupture: Along the Face Grain: Minimum Individual)) |
- |
1200 |
|
- |
| Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Rupture: Along the Face Grain: Average)) |
- |
1200 |
|
- |
| Cl. 9.1.6 (Table 3)(Cl. 9.1.6 (Table 3) (Modulus of Elasticity: Across the Face Grain: Minimum Individual)) |
- |
1200 |
|
- |
| Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Elasticity: Across the Face Grain: Average)) |
- |
1200 |
|
- |
| Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Elasticity: Along the Face Grain: Minimum Individual)) |
- |
1200 |
|
- |
| Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Elasticity: Along the Face Grain: Average)) |
- |
1200 |
|
- |
| Cl. 9.1.4(Cl. 9.1.4 (Tensile Strength: Sum of the Tensile Strength in two directions)) |
- |
800 |
|
- |
| Cl. 9.1.4 (Cl. 9.1.4 (Tensile Strength: Perpendicular to grain)) |
- |
800 |
|
- |
| Cl. 9.1.4(Cl. 9.1.4 (Tensile Strength: Parallel to grain)) |
- |
800 |
|
- |
| Cl.9.1.5,9.1.3.1.1(Cl.9.1.5 (Mycological Test),9.1.3.1.1 (Glue Shear Strength: Individual)) |
- |
1000 |
|
- |
| Cl.9.1.5,9.1.3.1.1(Cl.9.1.5 (Mycological Test),9.1.3.1.1 ( Glue Shear Strength: Average)) |
- |
1000 |
|
- |
| Cl. 9.1.3, 9.1.3.1.1 (Cl. 9.1.3 (Water Resistance Test) , 9.1.3.1.1 (Glue Shear Strength: Individual)) |
- |
1000 |
|
- |
| Cl. 9.1.3, 9.1.3.1.1 (Cl. 9.1.3 (Water Resistance Test ), 9.1.3.1.1 (Glue Shear Strength: Average)) |
- |
1000 |
|
- |
| Cl. 9.1.2, 9.1.2.1 (Cl. 9.1.2 (Glue Adhesion in Dry State), 9.1.2.1 ( Glue Shear Strength: Individual)) |
- |
750 |
|
- |
| Cl. 9.1.2, 9.1.2.1 (Cl. 9.1.2 (Glue Adhesion in Dry State), 9.1.2.1 ( Glue Shear Strength: Average )) |
- |
750 |
|
- |
| cl.5.1(manufacture - Veneers) |
- |
500 |
|
- |
| cl.5.1(manufacture - Veneers - moisture content) |
- |
500 |
|
- |
| cl.5.1.1(manufacture - Veneers - Defects in Veneers) |
- |
500 |
|
- |
| cl.5.2.2(Assembly - Thickness of Veneers) |
- |
250 |
|
- |
| 6.1(DIMENSIONS) |
- |
250 |
|
For BIS samples: 1.5 times of BIS testing charges (10% discount to BIS) |
|
10 Mar, 2027 |
-
- |
| 9913 |
PIONEER TESTING LABORATORY PRIVATE LIMITED
| 8176806
| IS 848 (2006) |
Synthetic resin adhesives for plywood (Phenolic And Aminoplastic) - Specification (Second Revision) |
All Type |
6400 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 4 Table (i)(BWP (BOiling WaterProof)) |
- |
4400 |
|
- |
| 4 Table (i)(BWR (Boiling Water Resistant)) |
- |
4400 |
|
- |
| 4 Table (i)(MR (Moisture Ressistant)) |
- |
4400 |
|
- |
| 5,7.4(Keeping Quality (Resistance to heat Polymerization)) |
- |
1500 |
|
- |
| 7.4(Acidity and Alkalinity ( pH)) |
- |
500 |
|
- |
|
10 Mar, 2027 |
-
- |
| 9914 |
PIONEER TESTING LABORATORY PRIVATE LIMITED
| 8176806
| IS 303 (1989) |
Plywood for General Purposes - |
All Type |
10450 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 11.4, Table 4(Static Bending Strength - Modulus of Rupture - Across the Face Grain - Minimum Individual) |
- |
750 |
|
- |
| 11.4, Table 4(Static Bending Strength - Modulus of Rupture - Across the Face Grain - Average) |
- |
750 |
|
- |
| 11.4, Table 4(Static Bending Strength - Modulus of Rupture - Along the Face Grain - Minimum Individual) |
- |
750 |
|
- |
| 11.4, Table 4(Static Bending Strength - Modulus of Rupture - Along the Face Grain - Average) |
- |
750 |
|
- |
| 11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Minimum Individual) |
- |
750 |
|
- |
| 11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Average) |
- |
750 |
|
- |
| 11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Minimum Individual) |
- |
750 |
|
- |
| 11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average) |
- |
750 |
|
- |
| 11.2.2(Glue Adhesion - Mycological test - 11.2.2, Part 7 of IS 1734 [for MR Garde only]) |
- |
1500 |
|
- |
| 11.2.1(Glue Adhesion - Water resistance test - 11.2.1.1 [for MR Grade]) |
- |
1000 |
|
- |
| 11.2.1(Glue Adhesion - Water resistance test - 11.2.1.1 [for BWR Grade]) |
- |
1000 |
|
- |
| 11.3(Moisture Content - Part 1 of IS 1734) |
- |
750 |
|
- |
| 8(Dimensions & Tolerances - Edge Straightness - Annexure C) |
- |
750 |
|
- |
| 8(Dimensions & Tolerances - Squareness - Annexure C) |
- |
750 |
|
- |
| 8(Dimensions & Tolerances - Thickness - Cl. 8) |
- |
300 |
|
- |
| 8(Dimensions & Tolerances - Width - Cl. 8) |
- |
300 |
|
- |
| 8(Dimensions & Tolerances - Length - Cl. 8) |
- |
300 |
|
- |
| 9(Workmanship and Finish - Cl.9, 8.3, Annexure C) |
- |
350 |
|
- |
| 5.2, Table 1, Table 2(Quality Requirements - Cl. 5.2) |
- |
300 |
|
- |
| cl. 13.2(marking) |
- |
200 |
|
- |
| cl. 13.1(marking) |
- |
200 |
|
- |
| 4(Grade - For BWR grade) |
- |
200 |
|
- |
| 4(Grade - For MR grade) |
- |
200 |
|
- |
| 5.1(Type - For AA Type) |
- |
200 |
|
- |
| 5.1(Type - For AB Type) |
- |
200 |
|
- |
| 5.1(Type - For BB Type) |
- |
200 |
|
- |
| 9(Workmanship and Finish - Cl.9, 8.3, Annexure C) |
- |
350 |
|
For BIS samples: 1.5 times of BIS testing charges (10% discount to BIS) |
|
10 Mar, 2027 |
-
- |
| 9915 |
PIONEER TESTING LABORATORY PRIVATE LIMITED
| 8176806
| IS 4990 (2011) |
Plywood for concrete shuttering works - Specification (Third Revision) |
All Type |
18850 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 4.0(Types) |
- |
350 |
|
- |
| 7.2(DIMENSIONS &
TOLERANCES
) |
- |
400 |
|
- |
| 7.3(DIMENSIONS &
TOLERANCES
) |
- |
200 |
|
- |
| 7.4(DIMENSIONS &
TOLERANCES
) |
- |
300 |
|
- |
| 8.1(WORKMANSHIP AND FINISH ) |
- |
300 |
|
- |
| 8.3(WORKMANSHIP AND FINISH ) |
- |
300 |
|
- |
| 10.1.1(MOISTURE CONTENT) |
- |
500 |
|
- |
| 10.1.2, 10.1.2.1 (Table-1)(GLUE ADHESION IN DRY STATE) |
- |
1000 |
|
- |
| 10.1.2, 10.1.2.2(GLUE ADHESION IN DRY STATE) |
- |
1000 |
|
- |
| 10.1.3, 10.1.3.1.1 (Table-1)(RESISTANCE TO WATER TEST) |
- |
1000 |
|
- |
| 10.1.3, 10.1.3.1.2(RESISTANCE TO WATER TEST) |
- |
1000 |
|
- |
| 10.1.4(RESISTANCE TO WATER TEST) |
- |
1000 |
|
- |
| 10.1.5(MYCOLOGICAL TEST ) |
- |
2000 |
|
- |
| 10.1.5, 10.1.5.1 (Table-1)(MYCOLOGICAL TEST ) |
- |
2000 |
|
- |
| 10.1.6(TENSILE STRENGTH) |
- |
1000 |
|
- |
| 10.1.7 (Table-2)(STATIC BENDING STRENGTH) |
- |
1600 |
|
- |
| 10.1.7 (Table-2)(STATIC BENDING STRENGTH) |
- |
1600 |
|
- |
| 10.1.8 (Table-3)(WET BENDING STRENGTH) |
- |
1600 |
|
- |
| 10.1.8 (Table-3)(WET BENDING STRENGTH) |
- |
1600 |
|
- |
| 10.1.9(RETENTION OF PRESERVATIVE) |
- |
2500 |
|
- |
| 12, 12.1(MARKING) |
- |
500 |
|
- |
|
10 Mar, 2027 |
-
- |
| 9916 |
BIS, Bengaluru Branch Laboratory (BNBL)
| None
| IS 15500 : Part 1 to 8 (2021) |
Deepwell Handpumps Components and Special Tools Specification |
- |
- View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
No Record Found
|
|
- |
-
Exclusion
Except Material Testing. |
| 9917 |
PIONEER TESTING LABORATORY PRIVATE LIMITED
| 8176806
| IS 5509 (2021) |
Fire Retardant Plywood - Specification ( Third Revision ) |
All Type |
14450 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 8.3 (Table 1)(b) 6 mm and above) |
- |
1500 |
|
- |
| 4.1(Flame retardant chemicals) |
- |
1500 |
|
- |
| 4.2(Flame retardant and preservative treatment) |
- |
1500 |
|
- |
| 4.3(Treatment) |
- |
500 |
|
- |
| 5(PREPARATION FOR TREATMENT) |
- |
500 |
|
- |
| 6.1.1(Treatment of Plywood by Pressure Impregnation after Manufacture) |
- |
0 |
|
- |
| 6.1.2(Soaking Treatment) |
- |
500 |
|
- |
| 6.2(Choice of Treatment) |
- |
500 |
|
- |
| 7(CONDITIONING AFTER TREATMENT) |
- |
0 |
|
- |
| 8.1(Dimensions) |
- |
800 |
|
- |
| 8.2(Thickness) |
- |
200 |
|
- |
| 8.3, Taable-1 (i)(Tolerance- Length) |
- |
200 |
|
- |
| 9(WORKMANSHIP AND FINISH) |
- |
500 |
|
- |
| 11 (a)(For flammability) |
- |
1000 |
|
- |
| 11 (b)(For flame penetration) |
- |
1200 |
|
- |
| 11 (c)(For rate of burning) |
- |
1500 |
|
- |
| 12.1 Table - 2 (i)(Moisture content, percent, Max) |
- |
500 |
|
- |
| 12.1 Table - 2 (ii)(Flammability (see Note 1), minutes, Min) |
- |
1000 |
|
- |
| 12.1 Table - 2 (iii)(Flame penetration (see Note 2), minutes, Min) |
- |
1200 |
|
- |
| 12.1 Table - 2 (iv)(Rate of burning (see Note 3), minutes, Min) |
- |
1500 |
|
- |
| 12.2(Other Tests) |
- |
0 |
|
- |
| 14(Marking) |
- |
500 |
|
- |
| 10(SAMPLING AND CRITERIA FOR CONFORMITY) |
- |
750 |
|
For BIS samples: 1.5 times of BIS testing charges (10% discount to BIS) |
|
10 Mar, 2027 |
-
- |
| 9918 |
PIONEER TESTING LABORATORY PRIVATE LIMITED
| 8176806
| IS 12406 (2003) |
Medium density fibre boards for general purpose - Specification (First Revision) |
All Type |
12900 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| Cl 4( Types) |
- |
500 |
|
- |
| Cl 7(Finish) |
- |
500 |
|
- |
| Cl 8(Dimensions & Tolerances) |
- |
1500 |
|
- |
| Cl 11.4(Test For Density) |
- |
750 |
|
- |
| Cl 11.5(Test For Moisture Content) |
- |
750 |
|
- |
| Cl 11.6(Test For water Absorption) |
- |
750 |
|
- |
| Cl 11.7.1(Due To General Absorption) |
- |
1000 |
|
- |
| Cl 11.7.2(Due To Surfacel Absorption) |
- |
1000 |
|
- |
| Cl 11.8(Tesr For Modulus Of Elasticity & Mudulus Of Rupture) |
- |
2500 |
|
- |
| Cl 11.9(Test For Internal Bond) |
- |
1500 |
|
- |
| Cl 11.10(Test For Screw Withdrawal Strength) |
- |
1500 |
|
- |
| Table 1 (iii)(Moisture content, Grade 1) |
- |
750 |
|
- |
| Table 1 (iii)(Moisture content, Grade 2) |
- |
750 |
|
- |
| Cl 4( Types) |
- |
500 |
|
- |
| Cl 7(Finish) |
- |
500 |
|
- |
| Cl 8(Dimensions & Tolerances) |
- |
1500 |
|
- |
| Cl 11.4(Test For Density) |
- |
750 |
|
- |
| Cl 11.5(Test For Moisture Content) |
- |
750 |
|
- |
| Cl 11.6(Test For water Absorption) |
- |
750 |
|
- |
| Cl 11.7.1(Due To General Absorption) |
- |
1000 |
|
- |
| Cl 11.7.2(Due To Surfacel Absorption) |
- |
1000 |
|
- |
| Cl 11.8(Tesr For Modulus Of Elasticity & Mudulus Of Rupture) |
- |
2500 |
|
- |
| Cl 11.9(Test For Internal Bond) |
- |
1500 |
|
- |
| Cl 11.10(Test For Screw Withdrawal Strength) |
- |
1500 |
|
- |
| Cl 11.10(Test For Screw Withdrawal Strength) |
- |
1500 |
|
- |
| Cl 11.9(Test For Internal Bond) |
- |
1500 |
|
- |
| Cl 11.8(Tesr For Modulus Of Elasticity & Mudulus Of Rupture) |
- |
2500 |
|
- |
| Cl 11.7.2(Due To Surfacel Absorption) |
- |
1000 |
|
- |
| Cl 11.6(Test For water Absorption) |
- |
750 |
|
- |
| Cl 11.5(Test For Moisture Content) |
- |
7500 |
|
- |
| Cl 11.4(Test For Density) |
- |
750 |
|
- |
| Cl 8(Dimensions & Tolerances) |
- |
500 |
|
- |
| Cl 7(Finish) |
- |
500 |
|
- |
| Cl 4( Types) |
- |
500 |
|
- |
| Cl 11.7.1(Due To General Absorption) |
- |
500 |
|
- |
|
10 Mar, 2027 |
-
- |
| 9919 |
PIONEER TESTING LABORATORY PRIVATE LIMITED
| 8176806
| IS 14587 (1998) |
Prelaminated Medium Density Fibre Board -specification |
All Type |
16500 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 8(Dimensions and tolerances) |
- |
2500 |
|
- |
| 10.2, Table-1(Test for Density) |
- |
750 |
|
- |
| 10.4, Table-1(Test for Water Absorption) |
- |
750 |
|
- |
| 10.5(test for swelling in water) |
- |
1000 |
|
- |
| 10.6(test for modulis of rupture) |
- |
2500 |
|
- |
| 10.7(Test for tensile strength perpendicular to Surface) |
- |
1000 |
|
- |
| 10.8(Test for tensile strength perpendicular to Surface after ageing ) |
- |
1000 |
|
- |
| 10.9(test screw withdrawal strength) |
- |
1000 |
|
- |
| 10.1(test for surface abrasion resistance) |
- |
1000 |
|
- |
| 10.11(test for resistance to steam) |
- |
1000 |
|
- |
| 10.12(test for resistance to crack) |
- |
1000 |
|
- |
| 10.13(test for resistance to cigarette burn) |
- |
1500 |
|
- |
| 10.14(test for resistance to stain) |
- |
1500 |
|
- |
|
10 Mar, 2027 |
-
- |
| 9920 |
PIONEER TESTING LABORATORY PRIVATE LIMITED
| 8176806
| IS 191 (2007) |
Copper - Specification (Fourth Revision) |
All Type |
7500 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 5.2(Billets) |
- |
500 |
|
- |
| 5.4-Table 3 (For Billets)(Mass) |
- |
300 |
|
- |
| 5.2-Table 3 (For Billets)(Diameter) |
- |
300 |
|
- |
| 5.2-Table 3 (For Billets)(Length) |
- |
300 |
|
- |
| 5.2-Table 3 (For Billets)(Deviation from straightness per 1000 mm length) |
- |
300 |
|
- |
| 5.4-Table 3 (Vertically continuously cast wire bars)(Mass) |
- |
300 |
|
- |
| 5.3-Table 3 (Vertically continuously cast wire bars)(Width) |
- |
300 |
|
- |
| 5.3-Table 3 (Vertically continuously cast wire bars)(thickness ) |
- |
300 |
|
- |
| 5.3-Table 3 (Vertically continuously cast wire bars)(Other dimention) |
- |
300 |
|
- |
| 5.4-Table 3 (Vertically static cast wire bars)(Mass) |
- |
300 |
|
- |
| 5.3-Table 3 (Vertically static cast wire bars)(Width) |
- |
300 |
|
- |
| 5.3-Table 3 (Vertically static cast wire bars)(thickness ) |
- |
300 |
|
- |
| 5.3-Table 3 (Vertically static cast wire bars)(Other dimention) |
- |
300 |
|
- |
| 5.4-Table 3 (Cast cakes)(Mass) |
- |
300 |
|
- |
| 5.3-Table 3 (Cast cakes)(Width) |
- |
300 |
|
- |
| 5.3-Table 3 (Cast cakes)(thickness ) |
- |
300 |
|
- |
| 5.3-Table 3 (Cast cakes)(Deviation from straightness per 1000 mm length) |
- |
300 |
|
- |
| 7.1 - Table 4(Copper + Silver(By difference)-IS440) |
- |
450 |
|
- |
| 7.1 - Table 4(Silver- IS 440) |
- |
450 |
|
- |
| 7.1 - Table 4(Copper (any Silver present to be counted as copper)-IS440) |
- |
450 |
|
- |
| 7.1 - Table 4(Phosphorus- IS 440) |
- |
450 |
|
- |
| 7.1 - Table 4(Arsenic- IS440) |
- |
750 |
|
- |
| 7.1 - Table 4(Antimony-IS440) |
- |
750 |
|
- |
| 7.1 - Table 4(Bismuth-IS 440) |
- |
1000 |
|
- |
| 7.1 - Table 4(Iron IS 440) |
- |
350 |
|
- |
| 7.1 - Table 4(Lead IS 440) |
- |
350 |
|
- |
| 7.1 - Table 4(Nickel IS 440) |
- |
350 |
|
- |
| 7.1 - Table 4(Oxygen IS 440) |
- |
1500 |
|
- |
| 7.1 - Table 4(Selenium - IS 440) |
- |
750 |
|
- |
| 7.1 - Table 4(Sulphur- IS 440) |
- |
350 |
|
- |
| 7.1 - Table 4(Tellurium- IS 440) |
- |
750 |
|
- |
| 7.1 - Table 4(Tin - IS 440) |
- |
350 |
|
- |
| 7.1 - Table 4(Znic-IS 440) |
- |
350 |
|
- |
| 7.1 - Table 4(Selenium + Telluuium- IS 440) |
- |
750 |
|
- |
| 7.1 - Table 4(Total Impurities- IS 440) |
- |
750 |
|
- |
| 8.1(FREEDOM FROM DEFECTS) |
- |
500 |
|
- |
| 8.2(FREEDOM FROM DEFECTS) |
- |
500 |
|
- |
| 9.1- Table 5(Mass Resistivity- IS 3635) |
- |
1500 |
|
- |
| 10(HYDROGEN EMBRITTLEMENT TEST- IS 191) |
- |
1500 |
|
- |
| 13(Marking) |
- |
300 |
|
- |
| 13(Marking) |
- |
300 |
|
- |
| 13(Marking) |
- |
300 |
|
- |
| 9.1 , 9.2 & 10(Resistivity & HYDROGEN EMBRITTLEMENT TEST) |
- |
1500 |
|
- |
| 9.1 , 9.2 & 10(Resistivity & HYDROGEN EMBRITTLEMENT TEST) |
- |
1500 |
|
- |
| 10(HYDROGEN EMBRITTLEMENT TEST- IS 191) |
- |
1500 |
|
- |
| 9.1- Table 5(Mass Resistivity- IS 3635) |
- |
1500 |
|
- |
| 8.2(FREEDOM FROM DEFECTS) |
- |
500 |
|
- |
| 8.1(FREEDOM FROM DEFECTS) |
- |
500 |
|
- |
| 7.1 - Table 4(Total Impurities- IS 440) |
- |
450 |
|
- |
| 7.1 - Table 4(Selenium + Telluuium- IS 440) |
- |
450 |
|
- |
| 7.1 - Table 4(Znic-IS 440) |
- |
300 |
|
- |
| 7.1 - Table 4(Tin - IS 440) |
- |
300 |
|
- |
| 7.1 - Table 4(Tellurium- IS 440) |
- |
450 |
|
- |
| 7.1 - Table 4(Sulphur- IS 440) |
- |
300 |
|
- |
| 7.1 - Table 4(Selenium - IS 440) |
- |
450 |
|
- |
| 7.1 - Table 4(Oxygen IS 440) |
- |
1500 |
|
- |
| 7.1 - Table 4(Nickel IS 440) |
- |
300 |
|
- |
| 7.1 - Table 4(Lead IS 440) |
- |
300 |
|
- |
| 7.1 - Table 4(Iron IS 440) |
- |
300 |
|
- |
| 7.1 - Table 4(Bismuth-IS 440) |
- |
1000 |
|
- |
| 7.1 - Table 4(Antimony-IS440) |
- |
750 |
|
- |
| 7.1 - Table 4(Arsenic- IS440) |
- |
750 |
|
- |
| 7.1 - Table 4(Phosphorus- IS 440) |
- |
300 |
|
- |
| 7.1 - Table 4(Copper (any Silver present to be counted as copper)-IS440) |
- |
450 |
|
- |
| 7.1 - Table 4(Silver- IS 440) |
- |
450 |
|
- |
| 7.1 - Table 4(Copper + Silver(By difference)-IS440) |
- |
450 |
|
- |
| 5.3-Table 3 (Cast cakes)(Deviation from straightness per 1000 mm length) |
- |
200 |
|
- |
| 5.3-Table 3 (Cast cakes)(thickness ) |
- |
200 |
|
- |
| 5.3-Table 3 (Cast cakes)(Width) |
- |
200 |
|
- |
| 5.4-Table 3 (Cast cakes)(Mass) |
- |
200 |
|
- |
| 5.4-Table 3 (Ingots)(Mass) |
- |
200 |
|
- |
| 5.3-Table 3 (Vertically static cast wire bars)(Other dimention) |
- |
200 |
|
- |
| 5.3-Table 3 (Vertically static cast wire bars)(thickness ) |
- |
200 |
|
- |
| 5.3-Table 3 (Vertically static cast wire bars)(Width) |
- |
200 |
|
- |
| 5.4-Table 3 (Vertically static cast wire bars)(Mass) |
- |
200 |
|
- |
| 5.3-Table 3 (Vertically continuously cast wire bars)(Other dimention) |
- |
200 |
|
- |
| 5.3-Table 3 (Vertically continuously cast wire bars)(thickness ) |
- |
200 |
|
- |
| 5.3-Table 3 (Vertically continuously cast wire bars)(Width) |
- |
200 |
|
- |
| 5.4-Table 3 (Vertically continuously cast wire bars)(Mass) |
- |
200 |
|
- |
| 5.2-Table 3 (For Billets)(Deviation from straightness per 1000 mm length) |
- |
200 |
|
- |
| 5.2-Table 3 (For Billets)(Length) |
- |
200 |
|
- |
| 5.2-Table 3 (For Billets)(Diameter) |
- |
200 |
|
- |
| 5.4-Table 3 (For Billets)(Mass) |
- |
200 |
|
- |
| 5.2(Billets) |
- |
200 |
|
- |
| 5.1- Table 2(γ) |
- |
200 |
|
- |
| 5.1- Table 2( β ) |
- |
200 |
|
- |
| 5.1- Table 2(α ) |
- |
200 |
|
- |
| 5.1- Table 2(R2 ) |
- |
200 |
|
- |
| 5.1- Table 2(R1) |
- |
200 |
|
- |
| 5.1- Table 2(R) |
- |
200 |
|
- |
| 5.1- Table 2(b1) |
- |
200 |
|
- |
| 5.1- Table 2(b) |
- |
200 |
|
- |
| 5.1- Table 2(h1) |
- |
200 |
|
- |
| 5.1- Table 2(h) |
- |
200 |
|
- |
| 5.1- Table 2(L1) |
- |
200 |
|
- |
| 5.1- Table 2(L) |
- |
200 |
|
- |
| 4-Table 1(GRADES/DESIGNATIONS) |
- |
200 |
|
- |
| 5.4-Table 3 (Ingots)(Mass) |
- |
200 |
|
- |
| 5.1- Table 2(γ) |
- |
200 |
|
- |
| 5.1- Table 2( β ) |
- |
200 |
|
- |
| 5.1- Table 2(α ) |
- |
200 |
|
- |
| 5.1- Table 2(R2 ) |
- |
200 |
|
- |
| 5.1- Table 2(R1) |
- |
200 |
|
- |
| 5.1- Table 2(R) |
- |
200 |
|
- |
| 5.1- Table 2(b1) |
- |
200 |
|
- |
| 5.1- Table 2(b) |
- |
200 |
|
- |
| 5.1- Table 2(h1) |
- |
200 |
|
- |
| 5.1- Table 2(h) |
- |
200 |
|
- |
| 5.1- Table 2(L1) |
- |
200 |
|
- |
| 5.1- Table 2(L) |
- |
200 |
|
- |
| 4-Table 1(GRADES/DESIGNATIONS) |
- |
200 |
|
- |
|
10 Mar, 2027 |
-
- |
| 9921 |
ELECTRICAL POWER RESEARCH LABORATORY, VADODARA
| 7175321
| IS 1180 : Part 3 (2021) |
Outdoor/Indoor Type Liquid Immersed Distribution Transformers Up to and Including 2 500 kVA, 33 kV — Specification Part 3 Natural/Synthetic Organic Ester Liquid Immersed |
Outdoor/Indoor Type Liquid Immersed Distribution Transf |
156750 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 21.2 a(Measurement of winding resistance
[IS 2026 (Part 1)].) |
- |
7050 |
|
Sample rating : 2500 kVA, 17 Tap |
| 21.2 b(Measurement of voltage ratio and check of phase
displacement [IS 2026 (Part 1)].) |
- |
9650 |
|
Sample rating : 2500 kVA, 17 Tap |
| 21.2 c(Measurement of short-circuit impedance
(principal tapping, when applicable) and load
loss at 50 percent and 100 percent load
[IS 2026 (Part 1)].) |
- |
7000 |
|
Sample rating : 2500 kVA, 17 Tap |
| 21.2 d(Measurement of no-load loss and current
[IS 2026 (Part 1)].) |
- |
4500 |
|
Sample rating : 2500 kVA, 17 Tap |
| 21.2 e(Measurement of insulation resistance
[IS 2026 (Part 1)].) |
- |
550 |
|
Sample rating : 2500 kVA, 17 Tap |
| 21.2 f(Induced over-voltage withstand test
[IS 2026 (Part 3)].) |
- |
1000 |
|
Sample rating : 2500 kVA, 17 Tap |
| 21.2 g(Separate-source voltage withstand test
[IS 2026 (Part 3)]) |
- |
1000 |
|
Sample rating : 2500 kVA, 17 Tap |
| 21.3 a(Lightning impulse test [IS 2026 (Part 3)].) |
- |
75000 |
|
Sample rating : 2500 kVA, 17 Tap with chopping |
| 21.3 b(Temperature-rise test [IS 2026 (Part 2)].) |
- |
20000 |
|
Sample rating : 2500 kVA, 17 Tap |
| 21.3 d(Pressure test) |
- |
9000 |
|
Sample rating : 2500 kVA, 17 Tap |
| 21.4 a(Determination of sound levels [IS 2026 (Part 10)];) |
- |
5000 |
|
Sample rating : 2500 kVA, 17 Tap |
| 21.4 c(No load current at 112.5 percent voltage
(see 6.9.2, 7.9.2, 8.9.2);) |
- |
1500 |
|
Sample rating : 2500 kVA, 17 Tap |
| 21.4 d(Paint adhesion test — The test is performed as
per ASTM D3359 (Standard Test Methods for
measuring adhesion by tape test).) |
- |
1000 |
|
Sample rating : 2500 kVA, 17 Tap |
| 21.4 e(BDV and Moisture content of liquid in the
transformer (IS 16081, IS 16099, IS 16899 or
IS 16659, whichever is applicable).) |
- |
5000 |
|
Sample rating : 2500 kVA, 17 Tap |
| 21.5(Pressure and Ester Liquid Leakage Test) |
- |
9500 |
|
Sample rating : 2500 kVA, 17 Tap
Pressure (Routine): 5000 and Leakage test : 4500 |
|
26 Aug, 2027 |
-
Exclusion: 21.3 c (Short-circuit withstand test [IS 2026 (Part 5)] (up to 200 kVA) and) , Cl.21.4 b (Short-circuit withstand test [IS 2026 (Part 5)] (above 200 kVA);) |
| 9922 |
ELECTRICAL POWER RESEARCH LABORATORY, VADODARA
| 7175321
| IS 1180 : Part 1 (2014) |
Outdoor Type Oil Immersed Distribution Transformers Upto and Including 2 500 kVA, 33kV - Specification Part 1 Mineral Oil Immersed (Fourth Revision) |
Outdoor Type Oil Immersed Distribution Transformers up |
156750 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 21.2 a)(Measurement of winding resistance ) |
- |
7050 |
|
Rating of sample 2500 kVA, 17 Tap |
| 21.2 b)( Measurement of voltage ratio and check of
phase displacemen) |
- |
9650 |
|
Rating of sample 2500 kVA, 17 Tap |
| 21.2 c)( Measurement of short-circuit impedance
(principal tapping, when applicable) and load
loss at 50 percent and 100 percent load) |
- |
7000 |
|
Rating of sample 2500 kVA, 17 Tap |
| 21.2 d)(Measurement of no-load loss and current) |
- |
4500 |
|
Rating of sample 2500 kVA, 17 Tap |
| 21.2 e)(Measurement of insulation resistance) |
- |
550 |
|
Rating of sample 2500 kVA, 17 Tap |
| 21.2 f)(Induced over-voltage withstand test) |
- |
1000 |
|
Rating of sample 2500 kVA, 17 Tap |
| 21.2 g)( Separate-source voltage withstand test) |
- |
1000 |
|
Rating of sample 2500 kVA, 17 Tap |
| 21.3(a )(Lightning impulse test) |
- |
75000 |
|
Rating of sample 2500 kVA, 17 Tap with chopping |
| 21.3(b)(Temperature-rise test) |
- |
20000 |
|
Rating of sample 2500 kVA, 17 Tap |
| 21.4 a)( Determination of sound levels) |
- |
5000 |
|
Rating of sample 2500 kVA, 17 Tap |
| 21.5.2.1(Type test : For Transformers Above 200 kVA and Up to Including 2 500 kVA) |
- |
9000 |
|
Rating of sample 2500 kVA, 17 Tap |
| 21.5.2.2(routine test :For Transformers Above 200 kVA and Up to Including 2 500 kVA) |
- |
5000 |
|
Rating of sample 2500 kVA, 17 Tap |
| 21.5.2.3( Oil leakage test (routine test)) |
- |
4500 |
|
Rating of sample 2500 kVA, 17 Tap |
| 21.4 c(No load current at 112.5 percent voltage.) |
- |
1500 |
|
Rating of sample 2500 kVA, 17 Tap |
| 21.4 d(Paint adhesion tests) |
- |
1000 |
|
Rating of sample 2500 kVA, 17 Tap |
| 21.4 e(BDV and moisture content of oil in the transformer) |
- |
5000 |
|
Rating of sample 2500 kVA, 17 Tap |
|
26 Aug, 2027 |
-
Exclusion: Cl.21.3(c) (Short-circuit withstand test), Cl.21.4 b (Short-circuit withstand test) |
| 9923 |
CIPET : CSTS - AGARTALA PLASTICS TESTING LABORATORY, (CIPET, AGARTALA)
| 5173304
| IS 12818 (2010) |
Unplasticized polyvinyl chloride (Pvc - U) screen and casing pipes for bore/tubewells - Specification (Second Revision) |
upto 350mm dia |
10350 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 9.6(Vicat Softening Temperature
IS 12235 (Part 2).) |
- |
1100 |
|
- |
| 9.5(Tensile Strength
IS 12235(Part 13)) |
- |
1500 |
|
including sampling charges of Rs. 400/- |
| 9.4 and Table 14(Resistance to External Blows at 0 ?C
IS 12235 (Part 9)) |
- |
1300 |
|
including sampling charges of Rs. 300/- |
| 9.3(Density
IS 12235 (Part 14)) |
- |
500 |
|
- |
| 9.2(Internal Diameter) |
- |
250 |
|
- |
| 9.1( Visual Appearance) |
- |
300 |
|
including visual appearance and colour |
| 9.1(Visual Appearance) |
- |
300 |
|
including visual appearance and colour |
| 8.4.1 and Table 13
Fig 3B & 4B(Dimensions of sealing elements) |
- |
250 |
|
- |
| 8.4.1 and Table 13
Fig 3B & 4B(Dimensions of sealing elements) |
- |
250 |
|
- |
| 8.4.1 and Table 13
Fig 3B & 4B(Dimensions of sealing elements) |
- |
250 |
|
- |
| 8.4.1 and Table 13
Fig 3B & 4B(Dimensions of sealing elements) |
- |
250 |
|
- |
| 8.4.1 and Table 13
Fig 3B & 4B(Dimensions of sealing elements) |
- |
250 |
|
- |
| 8.4.1 and Table 13
Fig 3B & 4B(Dimensions of sealing elements) |
- |
250 |
|
- |
| 8.4.1 and Table 13
Fig 3B & 4B(Dimensions of sealing elements) |
- |
250 |
|
- |
| 8.4(Sealing rings - Hardness) |
- |
375 |
|
- |
| 8.1 to 8.3 and Table 11 &12
Fig 3A & 4A(THREADING OF SCREEN ANDCASING PIPES.
IS 554.) |
- |
250 |
|
- |
| 8.1 to 8.3 and Table 11 &12
Fig 3A & 4A(THREADING OF SCREEN ANDCASING PIPES.
IS 554.) |
- |
250 |
|
- |
| 7.5 and Table 10
Fig 2A & 2B(Approximate Free Passage Area, in Percent (Mean Value) for Width of Slot (w)) |
- |
1500 |
|
including all dimensions of clause no. 7 & sampling charges of Rs. 500/- |
| 7.5 and Table 10
Fig 2A & 2B(Minimum number of slots on the circumference of the cross-section.) |
- |
1500 |
|
including all dimensions of clause no. 7 & sampling charges of Rs. 500/- |
| 7.5 and Table 10
Fig 2A & 2B(Summation of slot lengths over internal circumference of the cross- section.) |
- |
1500 |
|
including all dimensions of clause no. 7 & sampling charges of Rs. 500/- |
| 7.4 Table 8 & 9 Fig 1(Segmental length for Spigot (average of 4.0)) |
- |
1500 |
|
including all dimensions of clause no. 7 & sampling charges of Rs. 500/- |
| 7.4 Table 8 & 9 Fig 1(Segmental length,mm for socket (average of 4.0)) |
- |
1500 |
|
including all dimensions of clause no. 7 & sampling charges of Rs. 500/- |
| 7.4 Table 8 & 9
Fig 1(Segmental length, l3) |
- |
1500 |
|
including all dimensions of clause no. 7 & sampling charges of Rs. 500/- |
| 7.4 Table 8 & 9
Fig 1(Effective length, l2) |
- |
1500 |
|
including all dimensions of clause no. 7 & sampling charges of Rs. 500/- |
| 7.3.2(Rib height) |
- |
1500 |
|
including all dimensions of clause no. 7 & sampling charges of Rs. 500/- |
| 7.3.1(No.of Ribs) |
- |
1500 |
|
including all dimensions of clause no. 7 & sampling charges of Rs. 500/- |
| 7.2 and Table 5, 6 & 7
Fig 1B(Wall thickness, Max) |
- |
1500 |
|
including all dimensions of clause no. 7 & sampling charges of Rs. 500/- |
| 7.2 and Table 5, 6 & 7
Fig 1B(Wall thickness, Min) |
- |
1500 |
|
including all dimensions of clause no. 7 & sampling charges of Rs. 500/- |
| 7.1, 7.2 and Table 5, 6 & 7 Fig 1B(Mean outside dia over connection,mm (Take 4 reading and maximum valu reported)) |
- |
1500 |
|
including all dimensions of clause no. 7 & sampling charges of Rs. 500/- |
| 7.1, 7.2 and Table 5, 6 & 7 Fig 1B(Outer Diameter at any point, Max) |
- |
1500 |
|
including all dimensions of clause no. 7 & sampling charges of Rs. 500/- |
| 7.1, 7.2 and Table 5, 6 & 7 Fig 1B(Outer Diameter at any point , Min) |
- |
1500 |
|
including all dimensions of clause no. 7 & sampling charges of Rs. 500/- |
| 7.2 and Table 5, 6 & 7
Fig 1B(Mean Outer Diameter of Pipe , Max) |
- |
1500 |
|
including all dimensions of clause no. 7 & sampling charges of Rs. 500/- |
| 7.2 and Table 5, 6 & 7
Fig 1B(Mean Outer Diameter of Pipe, Min) |
- |
1500 |
|
including all dimensions of clause no. 7 & sampling charges of Rs. 500/- |
| 7.2 and Table 5, 6 & 7
Fig 1B(Nominal Diameter) |
- |
1000 |
|
including all dimensional measurements of clause 7 |
| 4.1.2 (Ref. Cl 11 of IS 4669)(Composition -Sulphated ash content ) |
- |
850 |
|
- |
| 4.1.2 (Ref. Cl 5.1. of IS 4669)(Composition - Loss on heating ) |
- |
0 |
|
- |
| 4.1.1 (Ref. 3.4.1. of IS 10151)(Composition - The monomer content (VCM content) in the
resin - Annex A ofIS 10151) |
- |
3000 |
|
- |
| 5(COLOUR) |
- |
3000 |
|
Including color and visual appearance |
| 8.4(Sealing elements
a. Elastomeric material
b. Shore A hardness of sealing Elements
) |
- |
375 |
|
- |
| 8.4(Width b) |
- |
250 |
|
including all dimensions of clause no. 8.4 |
| 8.3.1
&
8.3.2
(Threading of casing pipe (from 100 to 200 DN Table – 11 & Fig. 3A) & (from 250 to 400 DN Table – 12 & Fig. 4A)
Outside diameter
d1(+0, -0.3)
d2
d3
D1 (+0.3, -0)
D2
D4
D5 (+0.3, -0)
Z
h3 (+0, -0.1)
H4 (+0, -0.1)
) |
- |
250 |
|
including all dimensions of clause no. 8.1, 8.2, 8.3 |
| 8.2(Threading of casing pipe As per IS 554 (from 40 to 80mm DN)
Number of threads in 25.4mm
Pitch (P)
Height of thread (h)
Major (Gauge Diameter) d
Pitch(d2)
Minor (d1)
External Thread gauge length
Nominal
No. of turns of thread
max
min
) |
- |
250 |
|
including all dimensions of clause no. 8.1, 8.2, 8.3 |
| 7.5.1
7.5.2
(Slot Dimension (Table 10) Fig 2A & 2B
a. Minimum number of slot on the circumference
b. Σa±5%
c. Mean value of approximate free passage area (%) for width of slot (w)
d. Tolerance on width of slot (w)
e. Width of material between slot (b)) |
- |
1500 |
|
including all dimensions of clause no. 7 & sampling charges of Rs. 500/- |
| 5.0(Colour of Pipes) |
- |
300 |
|
including visual appearance and color |
| 9.7(Effect on Water
a) Lead (first extraction)
b) Lead (Third extraction)
c) Dialkyl Tin C4 & higher homologues measured as Tin (Third extraction)
d) Cadmium (All three extracts)
e) Mercury (All three extracts)
f) Other Toxic Substances
) |
- |
3000 |
|
- |
| 4.1.2(K-Value as per IS-4669) |
- |
1100 |
|
- |
| 4.1.1
(VCM Content as per IS 10151 (Annex A)) |
- |
3000 |
|
- |
| 7.1(Screen Pipes) |
- |
1500 |
|
including sampling charges of Rs. 500/- |
| 7.1(Screen Pipes) |
- |
0 |
|
- |
|
27 Jul, 2026 |
-
Included w.e.f. 04.08.2023. |
| 9924 |
PIONEER TESTING LABORATORY PRIVATE LIMITED
| 8176806
| IS 455 (2015) |
Portland slag cement - Specification |
All Type |
11600 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 7 Table 1 v(Transverse strength (optional)
IS 4031(Part 8) ) |
- |
1500 |
|
- |
| 7 Table 1 iv c(Compretsive Strenqth 672 ± 4 hr
IS 4031(Part 6)) |
- |
1500 |
|
- |
| 7 Table 1 iv b(Compretsive Strenqth 168 ± 2 hr
IS 4031(Part 6)) |
- |
1500 |
|
- |
| 7 Table 1 iv a(Compretsive Strenqth .72 ± 1 hr
IS 4031(Part 6)) |
- |
1500 |
|
- |
| 7 Table 1 iii b(Setting Time ( by Vicat Apparatus ), Final
IS 4031(Part 5)) |
- |
750 |
|
- |
| 7 Table 1 iii a(Setting Time ( by Vicat Apparatus ),Initial
IS 4031(Part 5)) |
- |
750 |
|
- |
| 7 Table 1 ii b(Soundness, Autoclave expansion
IS 4031(Part 3) ) |
- |
750 |
|
- |
| 7 Table 1 ii a(Soundness, Le-Chate1ier expansion
IS 4031(Part 3) ) |
- |
750 |
|
- |
| 7 Table 1 i(Fineness
IS 4031(Part 2)) |
- |
500 |
|
- |
| 6 - Table - 1 vii( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985) |
- |
600 |
|
- |
| 6 - Table - 1 vi(Chloride content - Cl 4.13 of IS 4032:1985) |
- |
600 |
|
- |
| 6 - Table - 1 v(Loss on ignition - Cl 6.2 of IS 4032:1985) |
- |
600 |
|
- |
| 6 - Table - 1 iv(Sulphide sulphur (S) - Cl 6.12 of IS 4032:1985) |
- |
600 |
|
- |
| 6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 6.11 of IS 4032:1985) |
- |
600 |
|
- |
| 6 - Table - 1 ii(Magnesia - Cl 6.8 of IS 4032:1985) |
- |
600 |
|
- |
| 6 - Table - 1 i(Insoluble residue - Cl 6.9 of IS 4032:1985) |
- |
600 |
|
- |
|
10 Mar, 2027 |
-
- |
| 9925 |
PIONEER TESTING LABORATORY PRIVATE LIMITED
| 8176806
| IS 13487 (1992) |
Irrigation equipment - Emitters - Specification |
All Type |
5287 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 7.1(Construction and workmanship) |
- |
500 |
|
- |
| 7.2(Flow path in emitters) |
- |
500 |
|
- |
| 7.3.1(Resistance to Hydrostatic pressure) |
- |
2000 |
|
- |
| 7.3.2(Resistance to Hydrostatic pressure) |
- |
2000 |
|
- |
| 7.3.3(Resistance to Hydrostatic pressure) |
- |
2000 |
|
- |
| 7.4.1(Emitter Pull Out In-line emitters) |
- |
1000 |
|
- |
| 7.4.2(Emitter Pull Out On-line emitters) |
- |
1000 |
|
- |
| 8.1.2(Uniformity of Emission Rate Unregulated emitters) |
- |
1000 |
|
- |
| 8.1.3(Uniformity of Emission Rate Regulated emitters) |
- |
1000 |
|
- |
| 8.2.2(Emission rate as a function of inlet pressure Unregulated emitters) |
- |
1000 |
|
- |
| 8.2.3(Emission rate as a function of inlet pressure Regulated emitters) |
- |
1000 |
|
- |
| 8.3(Determination of Emitter Exponent) |
- |
1500 |
|
- |
| 4(Classification) |
- |
300 |
|
- |
| 9(Marking) |
- |
500 |
|
- |
| 8.3(Determiaatlon of Emitter Exponent) |
- |
1500 |
|
- |
| 8.2.3(Regulated Emitters) |
- |
1000 |
|
- |
| 8.2.2(Unregulated Emttters) |
- |
1000 |
|
- |
| 8.2.1(Selection of Telt Sample) |
- |
500 |
|
- |
| 8.2(Emission Rate as a Function of Inlet Pressure) |
- |
1000 |
|
- |
| 8.1.3(Regulated Emitters) |
- |
1000 |
|
- |
| 8.1.2(Unregulated Emitters) |
- |
1000 |
|
- |
| 8.1(Uniformity of Emission Rate) |
- |
1000 |
|
- |
| 8.1.1(Number of Test Samples) |
- |
1000 |
|
- |
| 7.4.2(On-Line Emitters) |
- |
1000 |
|
- |
| 7.4.1(In-Line Emitters) |
- |
1000 |
|
- |
| 7.4(Emitter Pull-out) |
- |
1000 |
|
- |
| 7.3(Resistance to Hydrostatic Pressure) |
- |
2000 |
|
- |
| 7.2(Flow Paths In Emitter) |
- |
1000 |
|
- |
| 7.1(Construction and Workmanship) |
- |
500 |
|
- |
| 6.3(Accuracy or Measuring Devices) |
- |
500 |
|
- |
| 6.2(Test Conditions) |
- |
200 |
|
- |
| 6.1(Test Specimens) |
- |
500 |
|
- |
| 5.3(Materials) |
- |
0 |
|
- |
| 5.2(Emitter Ends) |
- |
0 |
|
- |
| 5.1(Connections) |
- |
0 |
|
- |
| 8.1.3(Uniformity of Emission Rate Regulated emitters) |
- |
1000 |
|
- |
| 8.1.2(Uniformity of Emission Rate Unregulated emitters) |
- |
1000 |
|
- |
|
10 Mar, 2027 |
-
- |
| 9926 |
PIONEER TESTING LABORATORY PRIVATE LIMITED
| 8176806
| IS 1489 (Part 1) (2015) |
Portland pozzolana cement - Specification: Part 1 fly Ash Based |
All Type |
8600 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 7 -Table 2- vi(Drying Shrinkage- IS 4031 Part 10) |
- |
800 |
|
- |
| 7 -Table 2- v(Transverse Strength - IS 4031 Part 8 (Optional)) |
- |
1000 |
|
- |
| 7 -Table 2- iv- c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6) |
- |
1200 |
|
- |
| 7 -Table 2- iv- b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6) |
- |
1200 |
|
- |
| 7 -Table 2- iv- a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6) |
- |
1200 |
|
- |
| 7 -Table 2-iii- b(Setting Time Final- 4031 Part 5) |
- |
400 |
|
- |
| 7 -Table 2- iii- a(Setting Time Initial- 4031 Part 5) |
- |
400 |
|
- |
| 7 -Table 2- ii- b(Expansion after aeration- 4031 Part 3) |
- |
500 |
|
- |
| 7 -Table 2- ii- b(Expansion by Autoclave- 4031 Part 3) |
- |
500 |
|
- |
| 7 -Table 2- ii- a(Expansion after aeration - 4031 Part 3) |
- |
500 |
|
- |
| 7 -Table 2- ii- a(Expansion by Le Chatelier- 4031 Part 3) |
- |
500 |
|
- |
| 7 -Table 2- i(Fineness 4031 Part 2) |
- |
500 |
|
- |
| 6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985) |
- |
500 |
|
- |
| 6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985) |
- |
500 |
|
- |
| 6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985) |
- |
600 |
|
- |
| 6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985) |
- |
600 |
|
- |
| 6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985) |
- |
600 |
|
- |
| 6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985) |
- |
600 |
|
- |
|
10 Mar, 2027 |
-
- |
| 9927 |
PIONEER TESTING LABORATORY PRIVATE LIMITED
| 8176806
| IS 3812 (Part 1) (2013) |
Pulverized fuel ash - Specification: Part 1 For use as pozzolana in cement, cement mortar and concrete |
All Type |
11100 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| Cl. 6.1, Table 1 - i(Silicon dioxide (SiO2) plus aluminium oxide (Al2O3) plus ironoxide (Fe2O3) - IS 1727) |
- |
400 |
|
- |
| Cl. 6.1, Table 1 - ii(Silicon dioxide (SiO2) - IS 1727) |
- |
400 |
|
- |
| Cl. 6.1, Table 1 - iii(Reactive Silica - Annex B) |
- |
350 |
|
- |
| Cl. 6.1, Table 1 - iv(Magnesium oxide (MgO) - IS 1727) |
- |
500 |
|
- |
| Cl. 6.1, Table 1 - v( Total sulphur as sulphur trioxide (SO3) - IS 1727) |
- |
500 |
|
- |
| Cl. 6.1, Table 1 - vi( Available alkalis as equivalent sodium oxide (Na2O) - Annex C) |
- |
800 |
|
- |
| Cl. 6.1, Table 1 - vii( Total Chlorides - IS 4032) |
- |
600 |
|
- |
| Cl. 6.1, Table 1 - viii( Loss on ignition - IS 1727) |
- |
750 |
|
- |
| Cl. 6.2(Moisture content of the fly ash when supplied in dry condition - Annex D) |
- |
500 |
|
- |
| 7.1-Table 2(i)(PHYSICAL REQUIREMENTS-Fineness) |
- |
1000 |
|
- |
| 7.1-Table 2(ii)(PHYSICAL REQUIREMENTS-Particles retained on 45 micron IS sieve) |
- |
750 |
|
- |
| 7.1-Table 2(iii)(PHYSICAL REQUIREMENTS-Average compressive strength) |
- |
1500 |
|
- |
| 7.1-Table 2(iv)(PHYSICAL REQUIREMENTS-Compressive strength at 28 days) |
- |
1500 |
|
- |
| 7.1-Table 2(v)(PHYSICAL REQUIREMENTS-Soundness by autoclave test ) |
- |
1200 |
|
- |
| 5.1, 7.1, table-2, iii(Lime reacitivity) |
- |
1500 |
|
- |
|
10 Mar, 2027 |
-
- |
| 9928 |
PIONEER TESTING LABORATORY PRIVATE LIMITED
| 8176806
| IS 269 (2015) |
Ordinary portland cement - Specification (Sixth Revision) |
All Type |
8850 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 7 Table-3 v(Transverse Strength - IS 4031 Part 8 (Optional)) |
- |
1500 |
|
- |
| 7 Table-3 iv c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6) |
- |
1200 |
|
- |
| 7 Table-3 iv b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6) |
- |
1200 |
|
- |
| 7 Table-3 iv a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6) |
- |
1200 |
|
- |
| 7 Table-3 iii b(Setting Time Final) |
- |
500 |
|
- |
| 7 Table-3 iii a(Setting Time Initial) |
- |
500 |
|
- |
| 7 Table-3 ii b(Expansion after aeration) |
- |
500 |
|
- |
| 7 Table-3 ii b(Expansion by Autoclave) |
- |
500 |
|
- |
| 7 Table-3 ii a(Expansion after aeration) |
- |
400 |
|
- |
| 7 Table-3 ii a(Expansion by Le Chatelier) |
- |
400 |
|
- |
| 7 Table-3 i.(Fineness) |
- |
400 |
|
- |
| 6.1 Table-2 viii(Alkali content) |
- |
400 |
|
- |
| 6.1 Table-2 vii(Chloride content) |
- |
300 |
|
- |
| 6.1 Table-2 vi(Loss on ignition) |
- |
300 |
|
- |
| 6.1 Table-2 v(Total Sulphur Content calculated as Sulphuric Anhydride) |
- |
350 |
|
- |
| 6.1 Table-2 iv(Magnesia) |
- |
300 |
|
- |
| 6.1 Table-2 iii.(Insoluble residue) |
- |
400 |
|
- |
| 6.1 Table-2 ii.(Ratio of percentage of alumina to that of iron oxide) |
- |
300 |
|
- |
| 6.1 Table-2 i.(Ratio of percentage of lime to percentage of silica, alumina and iron oxide) |
- |
300 |
|
- |
| 6 - Table - 1 viii(Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985) |
- |
800 |
|
- |
| 11(Marking) |
- |
200 |
|
- |
|
10 Mar, 2027 |
-
- |
| 9929 |
PIONEER TESTING LABORATORY PRIVATE LIMITED
| 8176806
| IS 1786 (2008) |
High strength deformed steel bars and wires for concretere inforcement - Specification (Fourth Revision) |
All Type |
15500 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| Cl 9.4(Load In Other Direction From Bend) |
- |
500 |
|
- |
| Cl 9.3(Load In One Direction) |
- |
500 |
|
- |
| Cl 8.1(UTM) |
- |
1000 |
|
- |
| Cl 7.2(Weight) |
- |
500 |
|
- |
| Cl 6.1(Length, Width & Thickness) |
- |
500 |
|
- |
| Cl 5(Deformations and Surface Characteristics) |
- |
200 |
|
- |
| Cl.9.4 & Cl. 9.4.1(Rebend test) |
- |
500 |
|
- |
| Cl. 9.3, Table 4(Bend Test ) |
- |
500 |
|
- |
| Cl. 8.1 Table 3(Elongation, percentage) |
- |
500 |
|
- |
| Cl. 8.1 Table 3(TS/YS ratio) |
- |
30 |
|
- |
| Cl. 8.1 Table 3(Tensile Strength (TS)) |
- |
1000 |
|
- |
| Cl. 8.1 Table 3(Yield Stress (YS)) |
- |
500 |
|
- |
| Cl. 7.2 Table -2 (Nominal Mass) |
- |
500 |
|
- |
| Cl. 6.1(Nominal Size) |
- |
500 |
|
- |
| Cl. 5 (Cl. 5 - Mean projected area of transverse ribs (1/3 of Ar)) |
- |
1200 |
|
- |
| Cl. 5 (Cl.5 Mean area of ribs/unit length (Ar), ) |
- |
1200 |
|
- |
| 8.18.1 Table 3(Total elongation at maximum force) |
- |
300 |
|
- |
| 5.7(PullOut (Bond Test)) |
- |
3500 |
|
- |
| Cl. 5.7(Average compressive strength of cubes at 28 days) |
- |
2500 |
|
- |
| Cl. 5.7(Bond Strength at 0.25 mm slip) |
- |
2500 |
|
- |
| Cl. 5.3 (b)(The ribs contributing the projected area - Transverse Ribs) |
- |
500 |
|
- |
| Cl. 5.3 (a)(The ribs contributing the projected area - Longitudinal Ribs) |
- |
500 |
|
- |
| Cl. 8.1 Table 3(Maximum Extension) |
- |
500 |
|
- |
| Cl. 6.2, 6.3 Table 1(Gross Cross Sectional Area, A) |
- |
500 |
|
- |
| 9.2(Tensile test,IS:1608(Pt1)-2018) |
- |
1000 |
|
- |
| Cl.4.2 of IS 1786 (Grade:- Fe 415,Fe 415D,Fe 415S,Fe 500,Fe 500D,Fe 500S,Fe 550,Fe 550D,Fe600,Fe 650,Fe 700)(Carbon-IS 228) |
- |
300 |
|
- |
| Cl.4.2 of IS 1786 (Grade:- Fe 415,Fe 415D,Fe 415S,Fe 500,Fe 500D,Fe 500S,Fe 550,Fe 550D,Fe600,Fe 650,Fe 700)(Sulphur-IS 228) |
- |
300 |
|
- |
| Cl.4.2 of IS 1786 (Grade:- Fe 415,Fe 415D,Fe 415S,Fe 500,Fe 500D,Fe 500S,Fe 550,Fe 550D,Fe600,Fe 650,Fe 700)(Phosphorous- IS 228) |
- |
300 |
|
- |
| Cl.4.2 of IS 1786 (Grade:- Fe 415,Fe 415D,Fe 415S,Fe 500,Fe 500D,Fe 500S,Fe 550,Fe 550D,Fe600,Fe 650,Fe 700)(Sulphur & Phosphorous) |
- |
300 |
|
- |
| Cl.4.2 of IS 1786 (Grade:- Fe 415D,Fe 415S, Fe 500D,Fe 500S,Fe 550D)(Carbon Equivalent) |
- |
300 |
|
- |
| Cl.4.2 of IS 1786 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.) |
- |
300 |
|
- |
| Cl.4.2 of IS 1786 (Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.) |
- |
500 |
|
- |
| Cl.4.2 of IS 1786 (Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.) |
- |
300 |
|
- |
| Cl.4.2 of IS 1786 (Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.) |
- |
300 |
|
- |
| Cl.4.2 of IS 1786 (Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.) |
- |
300 |
|
- |
| Cl.4.2 of IS 1786 (Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.) |
- |
300 |
|
- |
| Cl.4.2 of IS 1786 (Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.) |
- |
500 |
|
- |
| 4.2(Niobium (Nb)) |
- |
500 |
|
- |
| 4.2(Boron (B)) |
- |
500 |
|
- |
| 4.1( Aluminium %) |
- |
500 |
|
- |
| 4.1(Silicon %) |
- |
300 |
|
- |
| 4.1( Ti) |
- |
500 |
|
- |
|
10 Mar, 2027 |
-
- |
| 9930 |
CIPET : CSTS - AGARTALA PLASTICS TESTING LABORATORY, (CIPET, AGARTALA)
| 5173304
| IS 14885 (2022) |
Polyethylene Pipes for the Supply of Gaseous Fuels � Specification (First Revision) |
upto 355mm dia |
382175 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 4.2(Grade of material) |
- |
0 |
|
Total Test charges is given after deducting 25% discount. |
| 4.3(Nominal Diameter) |
- |
0 |
|
- |
| 4.4(Colour) |
- |
300 |
|
- |
| 5.1(Polyethylene
compound) |
- |
6425 |
|
Rs. 5800 for testing and Rs. 625 for specimen preparation |
| 5.3(Anti-oxidant) |
- |
0 |
|
- |
| 5.4(U-V stabilizer) |
- |
0 |
|
- |
| 5.7(PE Compound Quality Evaluation) |
- |
400000 |
|
- |
| 5.5(Effect of Gas
condensate on the
Hydrostatic strength) |
- |
6250 |
|
including specimen preparation charges Rs. 4250 |
| 5.6(Resistance to Weathering) |
- |
23800 |
|
including specimen preparation charges Rs.500 |
| 6.1(Mean out side Diameter (For less than or equal to 25 mm- Average of 8 , For higher diameters average of 6)) |
- |
500 |
|
including all dimensional measurements of pipe |
| 6.1(Out of Roundness (Ovality)) |
- |
500 |
|
including all dimensional measurements of pipe |
| 6.2(Wall thickness (Take 8 reading and Average will be repoted)) |
- |
500 |
|
including all dimensional measurements of pipe |
| 7(Finish) |
- |
300 |
|
- |
| 8.1(Internal pressure creep
rupture test for plain at 80 deg. C for
165h) |
- |
5050 |
|
including specimen preparation charges Rs. 250 |
| 8.1(Internal pressure creep
rupture test for plain
pipes at 20 deg. C for
100h) |
- |
4000 |
|
- |
| 8.1(Internal pressure creep
rupture test for plain
pipes at 80 deg. C for
1000 h) |
- |
11250 |
|
including specimen preparation charges Rs. 250 |
| 8.2(Reversion Test) |
- |
700 |
|
- |
| 8.3(Density) |
- |
500 |
|
- |
| 8.6(Thermal Stability (Oxidation Induction Time)) |
- |
2200 |
|
- |
| 8.7(Volatile Matter Content) |
- |
700 |
|
- |
| 8.8(Tensile Properties (Tensile Yield Strength and
Elongation at Break)) |
- |
1350 |
|
including specimen preparation charges Rs. 250 |
| 8.9(Resistance to Weathering) |
- |
9000 |
|
- |
| 6.4(Length of Pipe) |
- |
500 |
|
including all dimensional measurements of pipe |
| 8.4(Melt Flow Rate (MFR)) |
- |
1100 |
|
- |
| 8.5(Pigment Dispersion) |
- |
600 |
|
- |
| 8.10(Slow Crack Growth Rate Test) |
- |
11050 |
|
for type test @165hrs/80degree C, Rs.4800, specimen preparation charges Rs. 250 and type test @500hrs/80 degree C, Rs.5500, specimen preparation charges Rs. 500 |
| 8.11(Squeeze-off) |
- |
6350 |
|
including specimen preparation charges Rs. 250 & Hydrostatic pressure Rs. 4800 |
| 5.1, 5.7 Table 2(i) Conventional density (of base polymer)) |
- |
1125 |
|
including specimen preparation charges Rs. 625 |
| 5.1, 5.7 Table 2(ii) Melt flow rate (MFR)) |
- |
1100 |
|
- |
| 5.1, 5.7 Table 2(iii) Thermal stability (oxidation induction time)) |
- |
2200 |
|
- |
| 5.1, 5.7 Table 2(iv) Volatile content) |
- |
700 |
|
- |
| 5.1, 5.7 Table 2(v) Water content1)) |
- |
700 |
|
- |
| 5.1, 5.7 Table 2(vi) Pigment dispersion) |
- |
600 |
|
- |
| 5.1, 5.7 Table 3(iv) Resistance to slow crack growth rate) |
- |
11050 |
|
for type test @165hrs/80degree C, Rs.4800, specimen preparation charges Rs. 250 and type test @500hrs/80 degree C, Rs.5500, specimen preparation charges Rs. 500 |
| 5.3(Anti-Oxidant) |
- |
0 |
|
- |
| 5.4(U.V. Stabilizer) |
- |
0 |
|
- |
| 5.5(Effects of Gas Condensate on the Hydrostatic Strength) |
- |
5000 |
|
for filling up of synthetic condensate and stand in air (including specimen preparation charges Rs. 4000) |
| 5.6(ii) Hydraulic characteristics) |
- |
1000 |
|
including specimen preparation charges Rs. 250 |
| 5.6(iii) Thermal stability (Oxidation induction time)) |
- |
2200 |
|
- |
| 6(Dimensions of pipes) |
- |
500 |
|
- |
| 7(Finish) |
- |
300 |
|
- |
| 8.1(Hydraulic Characteristics) |
- |
20300 |
|
including all tests of hydraulic characteristics |
| 8.2(Reversion test) |
- |
700 |
|
- |
| 8.3(Density) |
- |
500 |
|
- |
| 8.4(Melt Flow Rate) |
- |
1100 |
|
- |
| 8.5(Pigment Dispersion) |
- |
600 |
|
- |
| 8.6(Thermal Stability (Oxidation Induction Time)) |
- |
2200 |
|
- |
| 8.7(Volatile Matter Content) |
- |
700 |
|
- |
| 8.9(Resistance to Weathering) |
- |
9000 |
|
- |
| 8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break)) |
- |
1350 |
|
including specimen preparation charges Rs. 250 |
| 8.10(Slow Crack Growth Rate Test) |
- |
11050 |
|
for type test @165hrs/80degree C, Rs.4800, specimen preparation charges Rs. 250 and type test @500hrs/80 degree C, Rs.5500, specimen preparation charges Rs. 500 |
| 8.11(Squeeze-of) |
- |
6350 |
|
including specimen preparation charges Rs. 250 |
| 4.2(Grade of material) |
- |
0 |
|
- |
| 4.3(Nominal Diameter) |
- |
0 |
|
- |
| 4.4(Colour) |
- |
300 |
|
Including colour and designation of pipe |
| 5.1(Polyethylene
compound) |
- |
7350 |
|
for pipe material Rs. 6600 with specimen charges Rs. 750, for granules Rs. 5800 with specimen charges Rs. 625 |
| 5.3(Anti-oxidant) |
- |
0 |
|
- |
| 5.4(U-V stabilizer) |
- |
0 |
|
- |
| 5.7(PE Compound Quality Evaluation) |
- |
400000 |
|
- |
| 5.5(Effect of Gas
condensate on the
Hydrostatic strength) |
- |
6250 |
|
including specimen charges of Rs. 4250/- |
| 5.6(Resistance to Weathering) |
- |
23800 |
|
including specimen charges of Rs. 500/- |
| 6.1(Mean out side Diameter (For less than or equal to 25 mm- Average of 8 , For higher diameters average of 6)) |
- |
500 |
|
including all dimensional measurement |
| 6.1(Out of Roundness (Ovality)) |
- |
500 |
|
including all dimensional measurement |
| 6.2(Wall thickness (Take 8 reading and Average will be repoted)) |
- |
500 |
|
including all dimensional measurement |
| 7(Finish) |
- |
300 |
|
- |
| 8.1(Internal pressure creep
rupture test for plain at 80 deg. C for
165h) |
- |
5050 |
|
including specimen charges of Rs. 250/- |
| 8.1(Internal pressure creep
rupture test for plain
pipes at 20 deg. C for
100h) |
- |
4000 |
|
- |
| 8.1(Internal pressure creep
rupture test for plain
pipes at 80 deg. C for
1000 h) |
- |
11250 |
|
including specimen charges of Rs. 250/- |
| 8.2(Reversion Test) |
- |
700 |
|
- |
| 8.3(Density) |
- |
500 |
|
- |
| 8.6(Thermal Stability (Oxidation Induction Time)) |
- |
2200 |
|
- |
| 8.7(Volatile Matter Content) |
- |
700 |
|
- |
| 8.8(Tensile Properties (Tensile Yield Strength and
Elongation at Break)) |
- |
1350 |
|
including specimen charges of Rs. 250/- |
| 8.9(Resistance to Weathering) |
- |
9000 |
|
- |
| 6.4(Length of Pipe) |
- |
500 |
|
including all dimensional measurement |
| 8.4(Melt Flow Rate (MFR)) |
- |
1100 |
|
- |
| 8.5(Pigment Dispersion) |
- |
600 |
|
- |
| 8.10(Slow Crack Growth Rate Test) |
- |
11050 |
|
including specimen preparation charges of Rs. 750/- |
| 8.11(Squeeze-off) |
- |
6350 |
|
including specimen preparation charges of Rs. 250/- |
| 5.1, 5.7 Table 2(i) Conventional density (of base polymer)) |
- |
1125 |
|
including specimen preparation charges of Rs. 625/- |
| 5.1, 5.7 Table 2(ii) Melt flow rate (MFR)) |
- |
1100 |
|
- |
| 5.1, 5.7 Table 2(iii) Thermal stability (oxidation induction time)) |
- |
2200 |
|
- |
| 5.1, 5.7 Table 2(iv) Volatile content) |
- |
700 |
|
- |
| 5.1, 5.7 Table 2(v) Water content1)) |
- |
700 |
|
- |
| 5.1, 5.7 Table 2(vi) Pigment dispersion) |
- |
600 |
|
- |
| 5.1, 5.7 Table 3(iv) Resistance to slow crack growth rate) |
- |
6000 |
|
including specimen preparation charges of Rs. 500/- |
| 5.3(Anti-Oxidant) |
- |
0 |
|
- |
| 5.4(U.V. Stabilizer) |
- |
0 |
|
- |
| 5.5(Effects of Gas Condensate on the Hydrostatic Strength) |
- |
6250 |
|
including specimen preparation charges of Rs. 4250/- |
| 5.6(ii) Hydraulic characteristics) |
- |
11250 |
|
including specimen preparation charges of Rs. 250/- |
| 5.6(iii) Thermal stability (Oxidation induction time)) |
- |
2200 |
|
- |
| 6(Dimensions of pipes) |
- |
500 |
|
including all dimensional measurement |
| 7(Finish) |
- |
300 |
|
- |
| 8.1(Hydraulic Characteristics) |
- |
20300 |
|
including specimen preparation charges of Rs. 500/- |
| 8.2(Reversion test) |
- |
700 |
|
- |
| 8.3(Density) |
- |
500 |
|
- |
| 8.4(Melt Flow Rate) |
- |
1100 |
|
- |
| 8.5(Pigment Dispersion) |
- |
600 |
|
- |
| 8.6(Thermal Stability (Oxidation Induction Time)) |
- |
2200 |
|
- |
| 8.7(Volatile Matter Content) |
- |
700 |
|
- |
| 8.9(Resistance to Weathering) |
- |
23800 |
|
including specimen preparation charges of Rs. 500/- |
| 8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break)) |
- |
1350 |
|
including specimen preparation charges of Rs. 250/- |
| 8.10(Slow Crack Growth Rate Test) |
- |
11050 |
|
including specimen preparation charges of Rs. 750/- |
| 8.11(Squeeze-of) |
- |
6350 |
|
including specimen preparation charges of Rs. 250/- |
| 4.2(Grade of material) |
- |
0 |
|
- |
| 4.3(Nominal Diameter) |
- |
0 |
|
- |
| 4.4(Colour) |
- |
300 |
|
including designation and colour |
| 5.1(Polyethylene
compound) |
- |
0 |
|
- |
| 5.7(PE Compound Quality Evaluation) |
- |
6425 |
|
including specimen preparation charges of Rs. 625/- |
| 5.5(Effect of Gas
condensate on the
Hydrostatic strength) |
- |
6250 |
|
including specimen preparation charges of Rs. 4250/- |
| 5.6(Resistance to Weathering) |
- |
23800 |
|
including specimen preparation charges of Rs. 500/- |
| 6.1(Mean out side Diameter (For less than or equal to 25 mm- Average of 8 , For higher diameters average of 6)) |
- |
500 |
|
including all dimensional measurement charges |
| 6.1(Out of Roundness (Ovality)) |
- |
500 |
|
including all dimensional measurement charges |
| 6.2(Wall thickness (Take 8 reading and Average will be repoted)) |
- |
500 |
|
including all dimensional measurement charges |
| 7(Finish) |
- |
300 |
|
- |
| 8.1(Internal pressure creep
rupture test for plain at 80 deg. C for
165h) |
- |
5050 |
|
including specimen preparation charges of Rs. 250/- |
| 8.1(Internal pressure creep
rupture test for plain
pipes at 20 deg. C for
100h) |
- |
4000 |
|
- |
| 8.1(Internal pressure creep
rupture test for plain
pipes at 80 deg. C for
1000 h) |
- |
11250 |
|
including specimen preparation charges of Rs. 250/- |
| 8.2(Reversion Test) |
- |
700 |
|
- |
| 8.3(Density) |
- |
500 |
|
- |
| 8.6(Thermal Stability (Oxidation Induction Time)) |
- |
2200 |
|
- |
| 8.7(Volatile Matter Content) |
- |
700 |
|
- |
| 8.8(Tensile Properties (Tensile Yield Strength and
Elongation at Break)) |
- |
1100 |
|
- |
| 8.9(Resistance to Weathering) |
- |
9000 |
|
- |
| 6.4(Length of Pipe) |
- |
500 |
|
including all dimensional measurement charges |
| 8.4(Melt Flow Rate (MFR)) |
- |
1100 |
|
- |
| 8.5(Pigment Dispersion) |
- |
600 |
|
- |
| 8.10(Slow Crack Growth Rate Test) |
- |
11050 |
|
- |
| 5.1, 5.7 Table 2(i) Conventional density (of base polymer)) |
- |
1125 |
|
including specimen preparation charges of Rs. 625/- |
| 5.1, 5.7 Table 2(ii) Melt flow rate (MFR)) |
- |
1100 |
|
- |
| 5.1, 5.7 Table 2(iii) Thermal stability (oxidation induction time)) |
- |
2200 |
|
- |
| 5.1, 5.7 Table 2(iv) Volatile content) |
- |
700 |
|
- |
| 5.1, 5.7 Table 2(v) Water content1)) |
- |
700 |
|
- |
| 5.1, 5.7 Table 2(vi) Pigment dispersion) |
- |
600 |
|
- |
| 5.1, 5.7 Table 3(iv) Resistance to slow crack growth rate) |
- |
6000 |
|
including specimen preparation charges of Rs. 500/- |
| 5.5(Effects of Gas Condensate on the Hydrostatic Strength) |
- |
6250 |
|
including specimen preparation charges of Rs.4250/- |
| 5.6(ii) Hydraulic characteristics) |
- |
11250 |
|
including specimen preparation charges of Rs. 250/- |
| 5.6(iii) Thermal stability (Oxidation induction time)) |
- |
2200 |
|
- |
| 8.1(Hydraulic Characteristics) |
- |
20300 |
|
including specimen preparation charges of Rs. 500/- |
| 7(Finish) |
- |
300 |
|
- |
| 8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break)) |
- |
1350 |
|
including specimen preparation charges of Rs. 50/- |
| 8.10(Slow Crack Growth Rate Test) |
- |
11050 |
|
including specimen preparation charges of Rs. 750/- |
| 8.11(Squeeze-of) |
- |
1300 |
|
- |
| 6(Dimensions of pipes) |
- |
500 |
|
including all dimensional measurement |
| 8.2(Reversion test) |
- |
700 |
|
- |
| 8.3(Density) |
- |
500 |
|
- |
| 8.4(Melt Flow Rate) |
- |
1100 |
|
- |
| 8.5(Pigment Dispersion) |
- |
600 |
|
- |
| 8.6(Thermal Stability (Oxidation Induction Time)) |
- |
2200 |
|
- |
| 8.7(Volatile Matter Content) |
- |
700 |
|
- |
| 8.9(Resistance to Weathering) |
- |
23800 |
|
including specimen preparation charges of Rs. 500/- |
|
27 Jul, 2026 |
-
Included w.e.f. 04.08.2023. Exclusion: Cl.5.3 (Anti-oxidant), Cl.5.4 (U-V stabilizer) |
