BIS - LIMS (Laboratory Information Management System)

Search by IS Number

Reset

15572 Results

S.No.

Lab Name

Osl Code

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

10831

RTRC LIMITED, GURUGRAM

9177406

IS 8783 : Part 4 : Sec 3 (1995)

Winding wires for submersible motors - Specification: Part 4 specification for individual wires: Sec 3 polyester and polypropylene insulated winding wires (First Revision)

13050 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(The winding wire shall either be wound on spools / reels conforming to IS 482-1981. or supplied in a coils packed and labelled.)	-	0	-
6.1(The winding wire shall carry following information marked on the lable on spool / reel / coil;)	-	0	-
6.1(a) Reference to this Indian Standard;)	-	0	-
6.1(b) Manufacturer's name,brand name or trade-mark;)	-	0	-
6.1(c) Size of conductor / maximum overall diameter,)	-	0	-
6.1(d) Length of conductor on spool / reel /coil;)	-	0	-
6.1(e) Number of lengths onspool / reel / coil (if more than one);)	-	0	-
6.1(f) Country of Manufacturer)	-	0	-
6.1(g) Year of Manufacture.)	-	0	-
6.2(BIS Certification Mark)	-	0	-
4(i) Material)	-	0	-
5(ii) Diameter [mm] Seperate wire:)	-	500	-
5(ii) Diameter [mm] Wire taken from cable:)	-	0	-
5(iii) Annealing test [Percentage] on Seperate wire:)	-	1000	-
5(iii) Annealing test [Percentage] on Wire taken from cable:)	-	0	-
5(d) Resistance test [Ohm/km corrected to 20°c)	-	1000	-
4.1, table 1 & 2(a) Thickness of Polyster (mm))	-	500	-
4.1, table 1 & 3(b) Thickness of Polypropylene (mm))	-	0	-
4.1, table 1 & 4(c) Total thickness of Insulation(mm))	-	500	-
4.2(Application of insulation)	-	0	-
4.3(Colour of Insuation)	-	0	-
4.4(Overall diameter (mm))	-	500	-
4(Before ageing Tensile strength [N/mm²])	-	1500	-
4(Before ageing Elongation at break [Percentage])	-	0	-
4(After ageing Tensile strength [N/mm²])	-	2500	-
4(Variation on tensile strangth [Percentage])	-	0	-
4(After ageing Elongation at break [Percentage])	-	0	-
4(Variation on elongation at break [Percentage])	-	0	-
4(Shrinkage test [Percentage])	-	1500	-
4(After Shrinkage Cracks found.)	-	0	-
4.1(Water absorption test [Gravimetric] [mg/cm²])	-	4500	-
4.1(Hot Deformation test [depth of indentation) [Percentage])	-	1500	-
4.1(Heat Shock Test - No cracks found)	-	1500	-
4.5(High Voltage test [Water Immersion test] 3 KV for 1 Minute)	-	2500	-
4.1(Insulation Resistance test [ohm-cm] At 27 ºC)	-	1500	-
4.1([Insulation Resistance test [ohm-cm] At 90 ºC)	-	0	-
5(The winding wire shall either be wound on spools / reels conforming to IS 482-1981. or supplied in a coils packed and labelled.)	-	0	-
6(The winding wire shall carry following information marked on the lable on spool / reel / coil;)	-	0	-
6(a) Reference to this Indian Standard;)	-	0	-
6(b) Manufacturer's name,brand name or trade-mark;)	-	0	-
6(c) Size of conductor / maximum overall diameter,)	-	0	-
6(d) Length of conductor on spool / reel /coil;)	-	0	-
6(e) Number of lengths onspool / reel / coil (if more than one);)	-	0	-
6(f) Country of Manufacturer Marking)	-	0	-
6(g) Year of Manufacture.)	-	0	-
6.2(BIS Certification Mark)	-	0	-
4(i) Material)	-	0	-
4(ii) Diameter [mm] Seperate wire:)	-	0	-
4(ii) Diameter [mm] Wire taken from cable)	-	0	-
4(iii) Annealing test [Percentage] on Seperate wire:)	-	0	-
4([iii) Annealing test [Percentage] on Wire taken from cable:)	-	0	-
4(d) Resistance test [Ohm/km corrected to 20°c])	-	0	-
4(a) Thickness of Polyster (mm))	-	0	-
4(b) Thickness of Polypropylene (mm))	-	0	-
4(c) Total thickness of Insulation(mm))	-	0	-
4(Application of insulation)	-	0	-
4(Colour of Insuation)	-	0	-
4(Overall diameter (mm))	-	0	-
4(Before ageing Tensile strength [N/mm²])	-	0	-
4(Before ageing Elongation at break [Percentage])	-	0	-
4(After ageing Tensile strength [N/mm²])	-	0	-
4(Variation on tensile strangth [Percentage])	-	0	-
4(After ageing Elongation at break [Percentage])	-	0	-
4(Variation on elongation at break [Percentage])	-	0	-
4(Shrinkage test [Percentage])	-	0	-
4(After Shrinkage Cracks found.)	-	0	-
4(Water absorption test [Gravimetric] [mg/cm²])	-	0	-
4(Hot Deformation test [depth of indentation) [Percentage])	-	0	-
4(Heat Shock Test - No cracks found Physical)	-	0	-
4(High Voltage test [Water Immersion test] 3 KV for 1 Minute)	-	0	-
4(Insulation Resistance test [ohm-cm] At 27 ºC)	-	0	-
4(Insulation Resistance test [ohm-cm] At 90 ºC)	-	0	-
Clause No. 3(Insulation Resistance (Volume Resistivity at test temperature 90 º C ))	-	0	-
Clause No. 3(Water absorption)	-	0	-
Clause No. 3(Hot Deformation)	-	0	-
Clause No. 3(Shrinkage)	-	0	-
Clause No. 3(Heat Shock)	-	0	-
Clause No. 3(Thickness of Insulation)	-	0	-
Clause No. 3(Annealing Test)	-	0	-
Clause No. 3(Conductor Diameter)	-	500	-
Clause No. 3(Overall Dimensions)	-	0	-
Clause No. 3(Insulation Resistance (Volume Resistivity at 27º C ))	-	0	-
Clause No. 3(High Voltage Test (Water Immersion test) at room temperature)	-	0	-
Clause No. 3(Conductor Resistance)	-	0	-

03 Apr, 2027

-
Included w.e.f. 24.04.2024

10832

RTRC LIMITED, GURUGRAM

9177406

IS 8783 : Part 4 : Sec 2 (1995)

Winding wires for submersible motors - specification: Part 4 specification for individual wires: Sec 2 crosslinked polyethylene insulated and polyamide jacketed wires (First Revision)

23500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Thickness of insulation)	-	500	-
4.2(Application of insulation and jacket)	-	0	-
4.3(Colour)	-	0	-
4.4(Overall diameter)	-	500	-
4.5(The overall surface of finished winding wire)	-	0	-
4.6(High voltage test)	-	2500	-
Table 1, Cl.4.1, Cl.4.4(Cross sectional area)	-	0	-
Table 1, Cl.4.1, Cl.4.4(Conductor diameter)	-	0	-
Table 1, Cl.4.1, Cl.4.4(Thickness of insulation)	-	500	-
Table 1, Cl.4.1, Cl.4.4(Thickness of PA jacket)	-	0	-
Table 1, Cl.4.1, Cl.4.4(Overall diameter)	-	500	-
Table 2, Cl.4.1,Cl.4.4(Conductor cross sectional area)	-	0	-
Table 2, Cl.4.1, Cl.4.4(Conductor composition No. of strands/Strand diameter)	-	0	-
Table 2, Cl.4.1, Cl.4.4(Conductor diameter)	-	0	-
Table 2, Cl.4.1, Cl.4.4(Thickness of insulation)	-	0	-
Table 2, Cl.4.1, Cl.4.4(Thickness of PA jacket)	-	0	-
Table 2, Cl.4.1, Cl.4.4(Overall diameter)	-	0	-
4.6(High Voltage Test (Water Immersion ) )	-	2500	-
4.5( Finish)	-	0	-
4.4(Overall Diameter)	-	0	-
4.3(Insulation : Colour)	-	0	-
4.2(Insulation : Application)	-	0	-
4.1(Insulation : Thickness)	-	0	-
3.2(Requirements(Cl. 4 Table 1 of IS: 8783 (part 2) Heat shock Test)	-	1500	-
3.2(Requirements(Cl. 4 Table 1 of IS: 8783 (part 2) Hot deformation Test )	-	1500	-
3.2(Requirements(Cl. 4 Table 1 of IS: 8783 (part 2) Water absorption)	-	4500	-
3.2(Requirements(Cl. 4 Table 1 of IS: 8783 (part 2) Shrinkage Test)	-	1500	-
3.2(Requirements(Cl. 4 Table 1 of IS: 8783 (part 2) Shrinkage Test)	-	0	-
3.2(Requirements(Cl. 4 Table 1 of IS: 8783 (part 2) Elongation Variation)	-	0	-
3.2(Requirements(Cl. 4 Table 1 of IS: 8783 (part 2) After Ageing Elongation Test)	-	3000	-
3.2(Requirements(Cl. 4 Table 1 of IS: 8783 (part 2) Tensile strength Variation)	-	0	-
3.2(Requirements(Cl. 4 Table 1 of IS: 8783 (part 2) After Ageing Tensile strength)	-	0	-
3.2(Requirements(Cl. 4 Table 1 of IS: 8783 (part 2) Befor Ageing Elongation Test)	-	1500	-
3.2(Requirements(Cl. 4 Table 1 of IS: 8783 (part 2) Befor Ageing Tensile strength)	-	0	-
3.2(Requirements(Cl. 4 Table 1 of IS: 8783 (part 2) Volume resistivity@ 85 °C)	-	1500	-
3.2(Requirements(Cl. 4 Table 1 of IS: 8783 (part 2) Volume resistivity@Room Temprature )	-	0	-
3.2(Dielectric Material )	-	0	-
3.1(Visual examination (Cl 4.1.2 of IS:8783 (Part I):95 )	-	0	-
3.1(Resistance Test ((Cl 6 of IS:8783(Part I):95 )	-	1000	-
3.1(Annealing Test(Cl. 6 of IS:8783(Part I):95 )	-	1000	-
3.1(Dimensions (Cl.5.1.1 of IS:8783 (Part I):95 )	-	500	-
3.1(Conductor (Cl.3.1 ) : ) Material (Cl.4 of IS:8783 (Part I):95 )	-	0	-

03 Apr, 2027

-
Included w.e.f. 24.04.2024

10833

Rajkot Metlab Services LLP, Rajkot

7183706

IS 210 (2009)

Grey iron castings - Specification (First Revision)

Grey iron castings

6900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Chemical Composition(chemical composition shall be as agreed to between the purchaser and the manufacturer.))	-	2000	-
15, Table 3(TENSIL.E TEST- IS 1608 Part1 )	-	1500	-
7.1(WORKMANSHIP AND FINISH)	-	100	-
10.1(FREEDOM FROM DEFECTS)	-	100	-
10.2(FREEDOM FROM DEFECTS)	-	100	-
13(SIZE OF TEST BARS-Diameter)	-	100	-
13(SIZE OF TEST BARS-Length)	-	100	-
16, Table 3(Hardness Test)	-	500	-
17,Annex B(TRANSVERSE TEST)	-	1500	-
9(IS 7754)	-	800	-
9(IS 7754)	-	800	-
9(Microstructure)	-	1800	-
21(Marking)	-	100	-
9(Microstructure)	-	1800	-
6(Chemical Composition(chemical composition shall be as agreed to between the purchaser and the manufacturer.))	-	2000	-
7.1(WORKMANSHIP AND FINISH)	-	100	-
10.1(FREEDOM FROM DEFECTS)	-	100	-
10.2(FREEDOM FROM DEFECTS)	-	100	-
13(SIZE OF TEST BARS-Diameter)	-	100	-
13(SIZE OF TEST BARS-Length)	-	100	-
15, Table 3(TENSIL.E TEST- IS 1608 Part1 )	-	1500	-
16, Table 3(Hardness Test)	-	500	-
17,Annex B(TRANSVERSE TEST)	-	1500	-
18(HYDROSTATIC TEST)	-	1500	-
18(HYDROSTATIC TEST)	-	1500	-

12 Jan, 2028

-
Exclusion: Cl.18 (Hydrostatic Test)

10834

RTRC LIMITED, GURUGRAM

9177406

IS 8783 : Part 4 : Sec 1 (1995)

Winding wires for submersible motors - Specification: Part 4 specification for indmdual wires: Sec 1 HR PVC insulated wires (First Revision)

13950 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.3.1 (Conductor)	-	0	-
Cl.4(Material)	-	0	-
Cl.5.1.1 (Dimensions)	-	0	-
Cl. 6(Annealing Test)	-	1000	-
Cl 6(Resistance Test)	-	1000	-
Cl 4.1.2 (Visual examination)	-	0	-
Cl.3.2(Dielectric Material )	-	0	-
Cl. 4 Table 1of IS: 8783 (part 2) (Volume resistivity)	-	0	-
Cl. 4 Table 1of IS: 8783 (part 2) (Volume resistivity)	-	0	-
Cl. 4 Table 1of IS: 8783 (part 2) (Tensile strength )	-	0	-
Cl. 4 Table 1of IS: 8783 (part 2) (Elongation)	-	0	-
Cl. 4 Table 1of IS: 8783 (part 2) (Tensile Strength)	-	0	-
Cl. 4 Table 1of IS: 8783 (part 2) (Variation)	-	0	-
Cl. 4 Table 1of IS: 8783 (part 2) (Elongation at Break )	-	0	-
Cl. 4 Table 1of IS: 8783 (part 2) (Variation)	-	0	-
Cl. 4 Table 1of IS: 8783 (part 2) (Shrinkage test )	-	1500	-
Cl. 4 Table 1of IS: 8783 (part 2) (Shrinkage test )	-	0	-
Cl. 4 Table 1of IS: 8783 (part 2) (Water absorption (Gravimetric) )	-	15	-
Cl. 4 Table 1of IS: 8783 (part 2) (Hot deformation Test )	-	1500	-
Cl. 4 Table 1of IS: 8783 (part 2) (Heat shock Test )	-	1500	-
Cl.4.1(Insulation )	-	0	-
Cl.4.2(Application)	-	0	-
Cl.4.3(Colour)	-	0	-
Cl.4.4(Overall Diameter)	-	500	-
Cl.4.5(Finish)	-	0	-
Cl.4.6(High Voltage Test Water Immersion )	-	2500	-
Cl No. 3.1(Conductor diameter)	-	500	-

03 Apr, 2027

-
Included w.e.f. 24.04.2024

10835

RTRC LIMITED, GURUGRAM

9177406

IS 4289 : Part 1 (1984)

Specification for flexible cables for lifts and other flexible connections: Part 1 elastomer insulated cables (First Revision)

35000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Conductor)	-	0	-
4(Separator)	-	0	-
5(Insulation)	-	0	-
5(Central heart)	-	0	-
7(Fillers)	-	0	-
8(Proofed tape)	-	0	-
9(Braid)	-	0	-
10(Sheath)	-	0	-
11(GENERAL DETAILS OF CONSTRUCTION)	-	0	-
12(Conductor)	-	0	-
17.1.f.1(Tensile strength and elongation at break for Sheath)	-	1000	-
17.1.e.2(Ageing in air oven for insulation)	-	0	-
17.1.e.3(Ageing in oxygen bomb for insulation)	-	1000	-
17.1.f.2(Ageing in air bomb for sheath)	-	0	-
17.1.f.3(Oil resistance for sheath)	-	3500	-
17.1.f.4(Tear resistance)	-	3500	-
17.1.g(High voltage water immersion test)	-	1000	-
17.1.h(Insulation resistance test)	-	1500	-
17.1.j(Static flexibility test)	-	4800	-
17.1.k(Flammability test)	-	3000	-
17.1.a(Persulphate test)	-	1000	-
17.1.b(Annealing test)	-	1200	-
17.1.c(Conductor resistance test)	-	1000	-
17.1.d(Test for thickness of insulation and sheath)	-	1000	-
17.1.e.1(Tensile strength and elongation at break for insulation)	-	1000	-
17.1.f.1(Tensile strength and elongation at break for Sheath)	-	1000	-
17.1.e.2(Ageing in air oven for insulation)	-	0	-
17.1.e.3(Ageing in oxygen bomb for insulation)	-	1000	-
17.1.f.2(Ageing in air bomb for sheath)	-	0	-
17.1.f.3(Oil resistance for sheath)	-	3500	-
13(Insulation)	-	0	-
14(Core identification)	-	0	-
15(Core assembly)	-	0	-
16.1(Overall covering- sheathed cables)	-	0	-
16.2(overall covering- braided cables)	-	0	-
17.1.a(Persulphate test)	-	1000	-
17.1.b(Annealing test)	-	1200	-
17.1.c(Conductor resistance test)	-	1000	-
17.1.d(Test for thickness of insulation and sheath)	-	1000	-
17.1.e.1(Tensile strength and elongation at break for insulation)	-	1000	-
17.1.f.4(Tear resistance)	-	3500	-
17.1.g(High voltage water immersion test)	-	1000	-
17.1.h(Insulation resistance test)	-	1500	-
17.1.j(Static flexibility test)	-	4800	-
17.1.k(Flammability test)	-	3000	-
17.1.a(IS 10810 Part-4)	-	0	-
17.1.b(IS 10810 Part-1)	-	0	-
17.1.c(IS 10810 Part-5)	-	0	-
17.1.d(IS 10810 Part-6)	-	0	-
17.1.e.1(IS 10810 Part-7)	-	0	-
17.1.f.1(IS 10810 Part-7)	-	0	-
17.1.e.2(IS 10810 Part-11)	-	0	-
17.1.e.3(IS 10810 Part-56)	-	0	-
17.1.f.2(IS 10810 Part-56)	-	0	-
17.1.f.3(IS 10810 Part-31)	-	0	-
17.1.f.4(IS 10810 Part-17)	-	0	-
17.1.g(IS 10810 Part-45)	-	0	-
17.1.h(IS 10810 Part-43)	-	0	-
17.1.j(IS 10810 Part-54)	-	0	-
17.1.k(IS 10810 Part-53)	-	0	-
17.1.a(IS 10810 Part-4)	-	0	-
17.1.b(IS 10810 Part-1)	-	0	-
17.1.c(IS 10810 Part-5)	-	0	-
17.1.d(IS 10810 Part-6)	-	0	-
17.1.e.1(IS 10810 Part-7)	-	0	-
17.1.f.1(IS 10810 Part-7)	-	0	-
17.1.e.2(IS 10810 Part-11)	-	0	-
17.1.e.3(IS 10810 Part-56)	-	0	-
17.1.f.2(IS 10810 Part-56)	-	0	-
17.1.f.3(IS 10810 Part-31)	-	0	-
17.1.f.4(IS 10810 Part-17)	-	0	-
17.1.g(IS 10810 Part-45)	-	0	-
17.1.h(IS 10810 Part-43)	-	0	-
17.1.j(IS 10810 Part-54)	-	0	-
17.1.k(IS 10810 Part-53)	-	0	-
3(Conductor)	-	0	-
4(Separator)	-	0	-
5(Insulation)	-	0	-
5(Central heart)	-	0	-
7(Fillers)	-	0	-
8(Proofed tape)	-	0	-
9(Braid)	-	0	-
10(Sheath)	-	0	-
11(GENERAL DETAILS OF CONSTRUCTION)	-	0	-
12(Conductor)	-	0	-
17.1.f.1(Tensile strength and elongation at break for Sheath)	-	0	-
17.1.e.2(Ageing in air oven for insulation)	-	0	-
17.1.e.3(Ageing in oxygen bomb for insulation)	-	0	-
17.1.f.2(Ageing in air bomb for sheath)	-	0	-
17.1.f.3(Oil resistance for sheath)	-	0	-
17.1.f.4(Tear resistance)	-	0	-
17.1.g(High voltage water immersion test)	-	0	-
17.1.h(Insulation resistance test)	-	0	-
17.1.j(Static flexibility test)	-	0	-
17.1.k(Flammability test)	-	0	-
17.1.a(Persulphate test)	-	0	-
17.1.b(Annealing test)	-	0	-
17.1.c(Conductor resistance test)	-	0	-
17.1.d(Test for thickness of insulation and sheath)	-	0	-
17.1.e.1(Tensile strength and elongation at break for insulation)	-	0	-
17.1.f.1(Tensile strength and elongation at break for Sheath)	-	0	-
17.1.e.2(Ageing in air oven for insulation)	-	0	-
17.1.e.3(Ageing in oxygen bomb for insulation)	-	0	-
17.1.f.2(Ageing in air bomb for sheath)	-	0	-
17.1.f.3(Oil resistance for sheath)	-	0	-
13(Insulation)	-	0	-
14(Core identification)	-	0	-
15(Core assembly)	-	0	-
16.1(Overall covering- sheathed cables)	-	0	-
16.2(overall covering- braided cables)	-	0	-
17.1.a(Persulphate test)	-	0	-
17.1.b(Annealing test)	-	0	-
17.1.c(Conductor resistance test)	-	0	-
17.1.d(Test for thickness of insulation and sheath)	-	0	-
17.1.e.1(Tensile strength and elongation at break for insulation)	-	0	-
17.1.f.4(Tear resistance)	-	0	-
17.1.g(High voltage water immersion test)	-	0	-
17.1.h(Insulation resistance test)	-	0	-
17.1.j(Static flexibility test)	-	0	-
17.1.k(Flammability test)	-	0	-
17.1.a(IS 10810 Part-4)	-	0	-
17.1.b(IS 10810 Part-1)	-	0	-
17.1.c(IS 10810 Part-5)	-	0	-
17.1.d(IS 10810 Part-6)	-	0	-
17.1.e.1(IS 10810 Part-7)	-	0	-
17.1.f.1(IS 10810 Part-7)	-	0	-
17.1.e.2(IS 10810 Part-11)	-	0	-
17.1.e.3(IS 10810 Part-56)	-	0	-
17.1.f.2(IS 10810 Part-56)	-	0	-
17.1.f.3(IS 10810 Part-31)	-	0	-
17.1.f.4(IS 10810 Part-17)	-	0	-
17.1.g(IS 10810 Part-45)	-	0	-
17.1.h(IS 10810 Part-43)	-	0	-
17.1.j(IS 10810 Part-54)	-	0	-
17.1.k(IS 10810 Part-53)	-	0	-
17.1.a(IS 10810 Part-4)	-	0	-
17.1.b(IS 10810 Part-1)	-	0	-
17.1.c(IS 10810 Part-5)	-	0	-
17.1.d(IS 10810 Part-6)	-	0	-
17.1.e.1(IS 10810 Part-7)	-	0	-
17.1.f.1(IS 10810 Part-7)	-	0	-
17.1.e.2(IS 10810 Part-11)	-	0	-
17.1.e.3(IS 10810 Part-56)	-	0	-
17.1.f.2(IS 10810 Part-56)	-	0	-
17.1.f.3(IS 10810 Part-31)	-	0	-
17.1.f.4(IS 10810 Part-17)	-	0	-
17.1.g(IS 10810 Part-45)	-	0	-
17.1.h(IS 10810 Part-43)	-	0	-
17.1.j(IS 10810 Part-54)	-	0	-
17.1.k(IS 10810 Part-53)	-	0	-

03 Apr, 2027

-
Included w.e.f. 24.04.2024

10836

RTRC LIMITED, GURUGRAM

9177406

IS 9857 (1990)

Welding cables - Specification (First Revision)

CABLE

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Conductor : Material )	-	0	-
5(SEPARATOR)	-	0	-
6(COVERING)	-	0	-
7(CONDUCTOR : CONSTRUCTION )	-	0	-
8(S E P A R A T O R)	-	0	-
9.1(C O V E R I N G : Application )	-	0	-
9.2(T h i c k n e s s o f C o v e r i n g)	-	0	-
9.3(T o l e r a n c e on Thickness o f C o v e r i n g)	-	0	-
9.4(A p p l i c a t i o n of C o v e r i n g)	-	0	-
9.5(Colour of C o v e r i n g)	-	0	-
10.1 a) 1)(Annealing test - IS 10810: Part 1)	-	1000	-
10.1 a) 2)(Conductor resistance tes - IS 10810 : Part 5)	-	500	-
10.1 c) 1)(Physical tests for covering : Tensile strength )	-	500	-
10.1 c) 1)(Physical tests for covering : Elongation at break )	-	500	-
10.1 c) 2)(Physical tests for covering - Ageing in Air oven : Tensile strength variation)	-	1000	-
10.1 c) 2)(Physical tests for covering -Ageing in Air oven : Elongation at break )	-	0	-
10.1 c) 2)(Physical tests for covering - Ageing in Air oven : Tensile strength )	-	0	-
10.1 c) 2)(Physical tests for covering -Ageing in Air oven : Elongation variation at break )	-	0	-
10.1 c) 3)(Physical tests for covering - Ageing in Air Bomb : Tensile strength variation )	-	1500	-
10.1 c) 3)(Physical tests for covering -Ageing in Air Bomb : Elongation variation at break )	-	0	-
10.1 c) 4)(Physical tests for covering - Oil Resistance : Tensile strength variation )	-	1500	-
10.1 c) 4)(Physical tests for covering - Oil Resistance : Elongation variation at break )	-	0	-
10.1 c) 5)(Hot set test )	-	500	-
10.1 c) 5)(Permanent set )	-	0	-
11.1(High Voltage Test ( Water Immersion Test ))	-	1000	-
11.2(Spark Test)	-	0	-
11.3(Static Flexibility Test)	-	1000	-
11.4(Flammability Test)	-	1000	-
12.1(Manufacturer's Identification)	-	0	-
12.2(Cable Identification)	-	0	-
12.3(Cable Code)	-	0	-
13.1(Packing )	-	0	-
13.2(Marking)	-	0	-
14(CABLE RATINGS)	-	0	-
15(VOLTAGE DROP)	-	0	-
Table 4(Copper purity test)	-	2500	-
Table 2(Oil resistance - Elongation)	-	0	-
Table 2(Oil resistance - Tensile strength )	-	1500	-
Table 2(Ageing in air bomb - Elongation)	-	0	-
Table 2(Ageing in air bomb - Tensile strength )	-	0	-
Table 1 (Thickness of covering)	-	0	if applicable
15.1 (d)(Heat Shock Test)	-	0	if applicable
15.1 (d)(Hot Deformation Test)	-	0	if applicable
15.1 (d)(Loss Of Mass Test)	-	0	if applicable
10.1(b), Table 1(Thickness of covering)	-	0	if applicable

03 Apr, 2027

-
-

10837

RTRC LIMITED, GURUGRAM

9177406

IS 4289 : Part 2 (2000)

Flexible cables for lifts and other flexible connections - Specification: Part 2 pvc insulated circular cables

24500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Conductor)	-	0	-
5(Separator)	-	0	-
6(Insulation)	-	0	-
7(Central heart)	-	0	-
8(Fillers)	-	0	-
9(tape)	-	0	-
10(braid)	-	0	-
11(sheath)	-	0	-
12(GENERAL DETAILS OF CONSTRUCTION)	-	0	-
13(Construction- Conductor)	-	0	-
14(Construction- Insulation)	-	0	-
14.2(Thickness of Insulation)	-	1000	-
14.3(Tolerance on Thickness of Insulation)	-	0	-
15(Core identification)	-	0	-
16(Core assembly)	-	0	-
17(overall covering)	-	0	-
17.1.1(Thickness of Sheath)	-	1000	-
17.1.2(Tolerance on Thickness of Sheath)	-	0	-
18.1.a.i(IS 10810 Part-1)	-	1500	-
18.1.a.ii(IS 10810 Part-5)	-	1000	-
18.1.b(IS 10810 Part-6)	-	1000	-
18.1.c.i(IS 10810 Part-7)	-	1000	-
18.1.c.i(IS 10810 Part-7)	-	0	-
18.1.c.ii(IS 10810 Part-11)	-	1000	-
18.1.c.ii(IS 10810 Part-11)	-	0	-
18.1.c.iii(IS 10810 Part-10)	-	3500	-
18.1.c.iii(IS 10810 Part-10)	-	0	-
18.1.c.iv(IS 10810 Part-14)	-	1500	-
18.1.c.iv(IS 10810 Part-14)	-	0	-
18.1.c.v(IS 10810 Part-12)	-	1500	-
18.1.c.v(IS 10810 Part-12)	-	0	-
18.1.c.vi(IS 10810 Part-60)	-	1000	-
18.1.c.vi(IS 10810 Part-60)	-	0	-
18.1.d(IS 10810 Part-45)	-	1000	-
18.1.e(IS 10810 Part-43)	-	1000	-
18.1. f(IS 10810 Part-54)	-	4500	-
18.1.g(IS 10810 Part-53)	-	3000	-

03 Apr, 2027

-
Included w.e.f. 24.04.2024

10838

RTRC LIMITED, GURUGRAM

9177406

IS 3975 (1999)

Low carbon galvanized steel wires, formed wires and tapes for armouring of cables - Specification (Third Revision)

4050 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
14 (a)(Marking)	-	0	-
14 (b)(Marking)	-	0	-
14 (c)(Marking)	-	0	-
14 (d)(Marking)	-	0	-
14 (e)(Marking)	-	0	-
14 (f)(Marking)	-	0	-
14 (g)(Marking)	-	0	-
14.2(Marking)	-	0	-
7(Dimensions)	-	500	-
7(Dimensions)	-	0	-
7(Dimensions)	-	0	-
7(Dimensions)	-	0	-
7(Dimensions)	-	0	-
7(Dimensions)	-	0	-
7(Dimensions)	-	0	-
11(Freedom from defects)	-	0	-
9.1(Galvanizing Requirements )	-	2500	-
9.2(Galvanizing Requirements )	-	0	-
9.3(Galvanizing Requirements )	-	0	-
8.1(Mechanical Properties (as per table 5 of IS 1608))	-	1500	-
8.1(Mechanical Properties (as per table 5 of IS 1608))	-	0	-
8.2(Mechanical Properties (as per IS 1717))	-	0	-
8.3(Mechanical Properties (as per IS 1755))	-	0	-
8.4(Mechanical Properties (as per IS 10810(Part- 42)))	-	0	-
14(Marking)	-	0	-
14 (a)(Marking)	-	0	-
14 (b)(Marking)	-	0	-
14 (c)(Marking)	-	0	-
14 (d)(Marking)	-	0	-
14 (e)(Marking)	-	0	-
14 (f)(Marking)	-	0	-
14 (g)(Marking)	-	0	-
14.2(Marking)	-	0	-
7(Dimensions)	-	0	-
7(Dimensions)	-	0	-
7(Dimensions)	-	0	-
7(Dimensions)	-	0	-
7(Dimensions)	-	0	-
7(Dimensions)	-	0	-
7(Dimensions)	-	0	-
11(Freedom from defects)	-	0	-
9.1(Galvanizing Requirements )	-	0	-
9.2(Galvanizing Requirements )	-	0	-
9.3(Galvanizing Requirements )	-	0	-
8.1(Mechanical Properties (as per table 5 of IS 1608))	-	0	-
8.1(Mechanical Properties (as per table 5 of IS 1608))	-	0	-
8.2(Mechanical Properties (as per IS 1717))	-	0	-
8.3(Mechanical Properties (as per IS 1755))	-	0	-
8.4(Mechanical Properties (as perIS 10810(Part- 42)))	-	0	-
Clause 6.1, Table-1(Sulphur)	-	100	-
Clause 6.1, Table-1(Phosphorus)	-	100	-
6.2(Phosphorus %)	-	0	-
6.2(Sulphur %)	-	0	-
6.2( Nitrogen%)	-	100	-
6.2(Phosphorus %)	-	0	-
6.2(Sulphur %)	-	0	-
6.2( Nitrogen%)	-	0	-
6.2(Phosphorus %)	-	0	-
6.2(Sulphur %)	-	0	-
6.2( Nitrogen%)	-	0	-

03 Apr, 2027

-
Included w.e.f. 24.04.2024

10839

RTRC LIMITED, GURUGRAM

9177406

IS 9968 : Part 1 (1988)

Specification for elastomer insulatedcables: Part 1 for working voltages up to and including 1100 volts (First Revision)

56500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1( Copper Cooduetor)	-	0	-
3.2(Aluminium conductor)	-	0	-
4.1(INSULATION : lnsulation for General Service)	-	0	-
4.2(INSULATION : Heat Resisting insulation)	-	0	-
4.3(INSULATION : Silicone Rubber Insulation)	-	0	-
5.1(TAPE : Proofed Tape)	-	0	-
5.2(TAPE : 2 Polyethyl_ Terephthalate ( PETP ) Tape or Plastic: Tape or Any Other SlIIitable Tape )	-	0	-
5.3(TAPE : Giass Tape)	-	0	-
6.1(FILLERS : )	-	0	-
7.1(BRAID : Textile Braid)	-	0	-
7.2(BRAID : Glass Braid )	-	0	-
8.1(SHEATH : General Service Insulated Cables and Flexible Cords)	-	0	-
8.2(SHEATH :Heat Resisting Insulated Cables)	-	0	-
9.1(PresenRtive Compound)	-	0	-
9.2(Varnish)	-	0	-
10( Conductor )	-	0	-
11(Separator tape)	-	0	-
12.2(Insulation : Thickness of Insufatien)	-	1000	-
12.4(Insulation : Allplication of Insulation)	-	0	-
13(CORE IDENTiFICATlON)	-	0	Additional charge, Rs. 1500 /- For each additional core
14(Tape)	-	0	-
15(BRAIDING)	-	0	-
16(COMPOUNDING AND VARNISHING)	-	0	-
17(LAYING UP OF CORES)	-	0	-
18( Binder tape)	-	0	-
19.2(Sheath : Thickness of Sheath)	-	1000	-
19.4( Sheath :Colour)	-	0	-
20( Overall diameter)	-	1000	-
21. (a)(Persulphate tests (for copper))	-	1000	-
21. (b)(Annealing Test (for coper))	-	1000	-
21. (c)( Tensile Test (for aluminium))	-	1000	-
21. (d)( Wrapping Test (for aluminium))	-	1000	-
21. (e)(Conductor Resistance )	-	1000	-
21.1( Tensile strength )	-	1000	-
22.1( Elongation)	-	1000	-
21.1(type test : Ageing In air oven)	-	5000	-
21.1(type test : Ageing in air bomb)	-	5000	-
21.1(type test : Ageing In oxygen bomb)	-	6500	-
21.1(type test : Hot set elongation)	-	1500	-
21.1(type test : Tear resistance )	-	3500	-
22.2(type test :Insulauon resistance High voltage (water immersron ) test)	-	5000	-
22.2(type test : Flammability test ( applicable to cables finished With SE 3 and SE 4 sheaths only) )	-	3000	-
21(Water absorption test)	-	8500	-
23(identification)	-	0	-
Cl No. 4.1(Ageing in oxygen bomb - Elongation)	-	0	-
Cl No. 4.1(Ageing in oxygen bomb - Tensile strength )	-	0	-
Cl No. 4.1(Ageing in air bomb - Elongation)	-	0	-
Cl No. 4.1(Ageing in air bomb - Tensile strength )	-	0	-
Cl No. 4.1(Ageing in air oven - Elongation)	-	0	-
Cl No. 4.1(Ageing in air oven - Tensile strength )	-	0	-
Cl No. 22.2(High Voltage Test (Water Immersion))	-	0	-
Cl No. 4.1(Insulation resistance)	-	2000	-
Cl No. 22.4, Appendix B (Flexing test for cords for use with electric iron )	-	0	-
Cl No. 22.2.2/22.2.3(High Voltage Test / Spark test)	-	2500	-
Cl No. 23.1, 23.2(Identification)	-	0	-
21.1((f) Oil resistance)	-	4500	-

03 Apr, 2027

-
Included w.e.f. 24.04.2024

10840

Adityapur Auto Cluster, Adityapur

5178506

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 18(Weight)	-	12000	-
Cl 15(Length, Width & Thickness)	-	12000	-
Cl 13(Y Groove Cracking Test)	-	12000	-
Cl 12(Sudden Load Applied)	-	12000	-
Cl 11.3(Press)	-	12000	-
Cl 10.3(UTM)	-	12000	-
Cl 7(Workmanship)	-	12000	-
Cl 18(Weight)	-	12000	-
Cl 15(Length, Width & Thickness)	-	12000	-
Cl 13(Y Groove Cracking Test)	-	12000	-
Cl 12(Sudden Load Applied)	-	12000	-
Cl 11.3(Press)	-	12000	-
Cl 10.3(UTM)	-	12000	-
Cl 7(Workmanship)	-	12000	-
Cl 18(Weight)	-	12000	-
Cl 15(Length, Width & Thickness)	-	12000	-
Cl 13(Y Groove Cracking Test)	-	12000	-
Cl 12(Sudden Load Applied)	-	12000	-
Cl 11.3(Press)	-	12000	-
Cl 10.3(UTM)	-	12000	-
Cl 7(Workmanship)	-	12000	-
Clause - 5, 8.1 & 8.2(E650, CARBON +EQUIVELENT )	-	12000	-
Cl. 15 (Cl. 15 Channel Section: Sweep)	-	12000	-
Cl. 15(Cl. 15 Channel Section: Camber)	-	12000	-
Cl. 15(Cl. 15 Channel Section: Flatness of Web (Concavity))	-	12000	-
Cl. 15(Cl. 15 Channel Section: Flatness of Web (Convexity))	-	12000	-
Cl. 15(Cl. 15 Channel Section: Flange Out of Square)	-	12000	-
Cl. 15(Cl. 15 Channel Section: Width of Flange)	-	12000	-
Cl. 15(Cl. 15 Channel Section: Depth)	-	12000	-
Cl. 15(Cl. 15 Square Bar: Out of Square)	-	12000	-
Cl. 15(Cl. 15 Square Bar: Side Width: Minimum)	-	12000	-
Cl. 15(Cl. 15 Square Bar: Side Width: Maximum)	-	12000	-
Cl. 15(Cl. 15 Round Bar: Out of Shape)	-	12000	-
Cl. 15(Cl. 15 Round Bar: Diameter Minimum)	-	12000	-
Cl. 15(Cl. 15 Round Bar: Diameter Maximum)	-	12000	-
Cl. 10.3 (Cl. 10.3 (Elongation %))	-	12000	-
Cl. 10.3 (Cl. 10.3 (Yield Stress))	-	12000	-
Cl. 10.3 (Cl. 10.3 (Tensile Strength))	-	12000	-
Clause - 5, 8.1 & 8.2(E650, ALUMINIUM)	-	12000	-
Clause - 5, 8.1 & 8.2(E650, SILICON)	-	12000	-
Clause - 5, 8.1 & 8.2(E650, NITROGEN)	-	12000	-
Clause - 5, 8.1 & 8.2(E650 ,MANGANESE)	-	12000	-
Clause - 5, 8.1 & 8.2(E650, PHOSPHURS)	-	12000	-
Clause - 5, 8.1 & 8.2(E650, SULPHUR)	-	12000	-
Clause - 5, 8.1 & 8.2(E650, CARBON)	-	12000	-
Clause - 5, 8.1 & 8.2(E600, CARBON +EQUIVELENT )	-	12000	-
Clause - 5, 8.1 & 8.2(E600, ALUMINIUM)	-	12000	-
Clause - 5, 8.1 & 8.2(E600, SILICON)	-	12000	-
Clause - 5, 8.1 & 8.2(E600, NITROGEN)	-	12000	-
Clause - 5, 8.1 & 8.2(E600 ,MANGANESE)	-	12000	-
Clause - 5, 8.1 & 8.2(E600, PHOSPHURS)	-	12000	-
Clause - 5, 8.1 & 8.2(E600, SULPHUR)	-	12000	-
Clause - 5, 8.1 & 8.2(E600, CARBON)	-	12000	-
Clause - 5, 8.1 & 8.2(E550, CARBON +EQUIVELENT )	-	12000	-
Clause - 5, 8.1 & 8.2(E550, ALUMINIUM)	-	12000	-
Clause - 5, 8.1 & 8.2(E550, SILICON)	-	12000	-
Clause - 5, 8.1 & 8.2(E550, NITROGEN)	-	12000	-
Clause - 5, 8.1 & 8.2(E550 ,MANGANESE)	-	12000	-
Clause - 5, 8.1 & 8.2(E550, PHOSPHURS)	-	12000	-
Clause - 5, 8.1 & 8.2(E550, SULPHUR)	-	12000	-
Clause - 5, 8.1 & 8.2(E550, CARBON)	-	12000	-
Clause - 5, 8.1 & 8.2(E450, CARBON +EQUIVELENT )	-	12000	-
Clause - 5, 8.1 & 8.2(E450, ALUMINIUM)	-	12000	-
Clause - 5, 8.1 & 8.2(E450, SILICON)	-	12000	-
Clause - 5, 8.1 & 8.2(E450, NITROGEN)	-	12000	-
Clause - 5, 8.1 & 8.2(E450 ,MANGANESE)	-	12000	-
Clause - 5, 8.1 & 8.2(E450, PHOSPHURS)	-	12000	-
Clause - 5, 8.1 & 8.2(E450, SULPHUR)	-	12000	-
Clause - 5, 8.1 & 8.2(E450, CARBON)	-	12000	-
Clause - 5, 8.1 & 8.2(E410, CARBON +EQUIVELENT )	-	12000	-
Clause - 5, 8.1 & 8.2(E410, ALUMINIUM)	-	12000	-
Clause - 5, 8.1 & 8.2(E410, SILICON)	-	12000	-
Clause - 5, 8.1 & 8.2(E410, NITROGEN)	-	12000	-
Clause - 5, 8.1 & 8.2(E410 ,MANGANESE)	-	12000	-
Clause - 5, 8.1 & 8.2(E410, PHOSPHURS)	-	12000	-
Clause - 5, 8.1 & 8.2(E410, SULPHUR)	-	12000	-
Clause - 5, 8.1 & 8.2(E410, CARBON)	-	12000	-
Clause - 5, 8.1 & 8.2(E350, CARBON +EQUIVELENT )	-	12000	-
Clause - 5, 8.1 & 8.2(E350, ALUMINIUM)	-	12000	-
Clause - 5, 8.1 & 8.2(E350, SILICON)	-	12000	-
Clause - 5, 8.1 & 8.2(E350, NITROGEN)	-	12000	-
Clause - 5, 8.1 & 8.2(E350 ,MANGANESE)	-	12000	-
Clause - 5, 8.1 & 8.2(E350, PHOSPHURS)	-	12000	-
Clause - 5, 8.1 & 8.2(E350, SULPHUR)	-	12000	-
Clause - 5, 8.1 & 8.2(E350, CARBON)	-	12000	-
Clause - 5, 8.1 & 8.2(E300, CARBON +EQUIVELENT )	-	12000	-
Clause - 5, 8.1 & 8.2(E300, ALUMINIUM)	-	12000	-
Clause - 5, 8.1 & 8.2(E300, SILICON)	-	12000	-
Clause - 5, 8.1 & 8.2(E300, NITROGEN)	-	12000	-
Clause - 5, 8.1 & 8.2(E300 ,MANGANESE)	-	12000	-
Clause - 5, 8.1 & 8.2(E300, PHOSPHURS)	-	12000	-
Clause - 5, 8.1 & 8.2(E300, SULPHUR)	-	12000	-
Clause - 5, 8.1 & 8.2(E300, CARBON)	-	12000	-
Clause - 5, 8.1 & 8.2(E275, CARBON +EQUIVELENT )	-	12000	-
Clause - 5, 8.1 & 8.2(E275, ALUMINIUM)	-	12000	-
Clause - 5, 8.1 & 8.2(E275, SILICON)	-	12000	-
Clause - 5, 8.1 & 8.2(E275, NITROGEN)	-	12000	-
Clause - 5, 8.1 & 8.2(E275 ,MANGANESE)	-	12000	-
Clause - 5, 8.1 & 8.2(E275, PHOSPHURS)	-	12000	-
Clause - 5, 8.1 & 8.2(E275, SULPHUR)	-	12000	-
Clause - 5, 8.1 & 8.2(E275, CARBON)	-	12000	-
Clause - 5, 8.1 & 8.2(E250, CARBON +EQUIVELENT )	-	12000	-
Clause - 5, 8.1 & 8.2(E250, ALUMINIUM)	-	12000	-
Clause - 5, 8.1 & 8.2(E250, SILICON)	-	12000	-
Clause - 5, 8.1 & 8.2(E250, NITROGEN)	-	12000	-
Clause - 5, 8.1 & 8.2(E250 ,MANGANESE)	-	12000	-
Clause - 5, 8.1 & 8.2(E250, PHOSPHURS)	-	12000	-
Clause - 5, 8.1 & 8.2(E250, SULPHUR)	-	12000	-
Clause - 5, 8.1 & 8.2(E250, CARBON)	-	12000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon Equivalent- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12000	-
Cl. 15, 16(Off Centre of Web)	-	12000	-
Cl. 15, 16(Flange out of square (I beam))	-	12000	-
Cl. 15, 16(Width of flange (I Beam))	-	12000	-
Cl. 15, 16(Depth (I Beam))	-	12000	-
Cl. 15, 16(Mass (Plate))	-	12000	-
Cl. 15, 16(Flange Slope)	-	12000	-
Cl. 15, 16(Web Thickness)	-	12000	-
Cl. 15, 16(Flange Thickness)	-	12000	-
Cl. 15, 16(Out of Square (Flat))	-	12000	-
Cl. 15, 16(Width )	-	12000	-
Cl. 15, 16(Thickness )	-	12000	-
Cl. 15, 16(Sectional Area )	-	12000	-
Cl. 15, 16(Camber (Angle))	-	12000	-
Cl. 15, 16(Out of Square (Angle))	-	12000	-
Cl. 15, 16(Weight)	-	12000	-
Cl. 15, 16(Leg Length Difference (Angle))	-	12000	-
Cl. 15, 16(Leg Length B (Angle))	-	12000	-
Cl. 15, 16(Leg Length A (Angle))	-	12000	-
Cl. 15, 16(Toe Radius R2)	-	12000	-
Cl. 15, 16(Root Radius R1)	-	12000	-
Cl 18(Weight)	-	12000	-
Cl 15(Length, Width & Thickness)	-	12000	-
Cl 13(Y Groove Cracking Test)	-	12000	-
Cl 12(Sudden Load Applied)	-	12000	-
Cl 11.3(Press)	-	12000	-
Cl 10.3(UTM)	-	12000	-
Cl 7(Workmanship)	-	12000	-
14.1(Soundness test)	-	12000	-
14.2(Grain Size)	-	12000	-
14.2(Inclusion)	-	12000	-
Cl 7(Workmanship)	-	12000	-
Cl 10.3(UTM)	-	12000	-
Cl 11.3(Press)	-	12000	-
Cl 12(Sudden Load Applied)	-	12000	-
Cl 13(Y Groove Cracking Test)	-	12000	-
Cl 15(Length, Width & Thickness)	-	12000	-
Cl 18(Weight)	-	12000	-
Clause 8, Table 1, Note 2(Any Instrumental Method/Chemical Method)	-	12000	-
Clause 8, Table 1, Note 5(Any Instrumental Method/Chemical Method)	-	12000	-
Clause 8, Table 1, Note 5(Any Instrumental Method/Chemical Method)	-	12000	-
Clause 8, Table 1, Note 5(By Calculation)	-	12000	-
Clause 8, Table 1, Note 6(Any Instrumental Method/Chemical Method)	-	12000	-
Clause 8, Table 1, Note 6(By Calculation)	-	12000	-
Clause 7(IS 2062)	-	12000	-
Clause 11.3(IS 1599)	-	12000	-
Clause 12(IS 1757)	-	12000	-
Clause 15, Table 4(IS 2062)	-	12000	-
16(Tolerance)	-	12000	-
20(Marking)	-	12000	-
20(MARKING)	-	12000	-
8(Micro Alloying elements)	-	12000	-
8(Niobium as Nb)	-	12000	-
8(Vanadium as V)	-	12000	-
8(Titanium as Ti)	-	12000	-
10(Tensile Strength-IS:1608(P1)-22)	-	12000	-
10(Yield Stress-IS:1608(P1)-22)	-	12000	-
10(Elongation on SoA 5.65mm GL)	-	12000	-
15(Mass -SOP MT-23)	-	12000	-
15(Sectional Area)	-	12000	-
15(Dimension -D)	-	12000	-
15(Dimension -B)	-	12000	-
15(Thickness - t)	-	12000	-
15(Thickness - T)	-	12000	-
15(Flange Slope)	-	12000	-
15(Radius R1)	-	12000	-
15(Radius R2)	-	12000	-
15(Mass -SOP MT-23)	-	12000	-
15(Sectional Area)	-	12000	-
15(Dimension -D)	-	12000	-
15(Dimension -B)	-	12000	-
15(Thickness - t)	-	12000	-
15(Thickness - T)	-	12000	-
15(Radius R1)	-	12000	-
15(Radius R2)	-	12000	-
15(Mass -SOP MT-23)	-	12000	-
15(Sectional Area)	-	12000	-
15(Dimensions AxB)	-	12000	-
15(Thickness - t)	-	12000	-
15(Radius -R1)	-	12000	-
15(Radius -R2)	-	12000	-
15(Diameter)	-	12000	-
15(Sectional Area)	-	12000	-
15(Mass per metre)	-	12000	-
15(Mass per metre)	-	12000	-
15(Ovality)	-	12000	-
15(Side Width)	-	12000	-
15(Sectional Area)	-	12000	-
15(Mass per metre)	-	12000	-
15(Out of Square)	-	12000	-
9(Preparation of test sample)	-	12000	-
Clause 8, Table 1, Note 2(Aluminium)	-	12000	-
Clause 8, Table 1, Note 5(Niobium)	-	12000	-
Clause 8, Table 1, Note 5(Titanium)	-	12000	-
Clause 8, Table 1, Note 5(Nb+V+Ti)	-	12000	-
Clause 8, Table 1, Note 6(Boron)	-	12000	-
Clause 8, Table 1, Note 6(Cr+Ni)	-	12000	-
Clause 7(Freedom from Defect)	-	12000	-
Clause 11.3(Bend Test)	-	12000	-
Clause 12(Impact Test)	-	12000	-
Clause 15, Table 4(Dimension)	-	12000	-
5(General Requirements)	-	12000	-
4(MARKING)	-	12000	-

28 Jun, 2027

-
Exclusion Cl.13 Y-groove crackability test, Cl.14 other tests

10841

Alpha Test House Services LLP (160), Sahibzada Ajit Singh Nagar

9138706

IS 2098 (1997)

Asbestos cement building boards - Specification (First Revision)

Asbestos cement building boards

13000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1 Table -1( TOLERANCES - 1.Tolerance on Length & Width)	-	500	-
7.2 Table -1(2.Tolerance on Thickness )	-	500	-
8.2(TESTS -Load Bearing Capacity Test )	-	5000	-
8.3 Table 1 & 7.1(TESTS-Measurement of Thickness )	-	1000	-
8.4(TESTS-Water Absorption Test )	-	1500	-
11(MARKING-Each board shall be stamped or marked by any suitable method on non weathering side with the following information: )	-	500	-
Cl. 8.2 (Cl. 8.2 ,Tests-Load Bearing Capacity test, Class-A/B/C , Individual Load )	-	5000	-
Cl. 8.2 (Cl. 8.2 ,Tests-Load Bearing Capacity test, Class A/B/C ,Average Load)	-	5000	-
Cl.6(General apperance and finish)	-	1000	-
Cl. 7.2 Table -1 (Cl. 7.1 , Table-1 (Thickness))	-	1000	-
Cl. 7.1 Table -1 (Cl. 7.1 , Table-1 (Width))	-	1000	-
Cl. 7.1 Table -1 (Cl. 7.1 ,Table-1 (Length))	-	1000	-
7.1 Table -1( TOLERANCES - 1.Tolerance on Length & Width)	-	-	-
7.2 Table -1(2.Tolerance on Thickness )	-	-	-
8.2(TESTS -Load Bearing Capacity Test )	-	-	-
8.3 Table 1 & 7.1(TESTS-Measurement of Thickness )	-	-	-
8.4(TESTS-Water Absorption Test )	-	-	-
11(MARKING-Each board shall be stamped or marked by any suitable method on non weathering side with the following information: )	-	-	-

31 Dec, 2029

-
Included w.e.f. 12.04.2024

10842

Alpha Test House Services LLP (160), Sahibzada Ajit Singh Nagar

9138706

IS 2096 (1992)

Asbestos cement flat sheets - Specification (First Revision)

Asbestos cement flat sheets

13000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1(DIMENSIONS AND TOLERANCES - Nominal Thickness)	-	1000	-
7.2(DIMENSIONS AND TOLERANCES - Nominal Length and Width)	-	1000	-
7.3.1 & 7.3.2 & 7.3.3(DIMENSIONS AND TOLE+I7RANCES - 1.Tolerance on Thickness 2.Tolerance on Leng+I58th & Width 3. Tolerance on shape )	-	1000	-
8.2 Table -1(Tests -Bending Strenth Test)	-	4500	-
8.3(Tests- Thickness)	-	1000	-
8.4 and 8.5 & 7.3.3.1 & 7.3.3.2(Tests- 1.Straigthness of edges 2.Squareness of edges)	-	3000	-
8.6(Density)	-	1100	-
11.1(Marking- Each sheet shall be stamped or marked by any suitable method on the surface not exposed to the weather with the following information:)	-	200	-
11.2(Standard Mark.)	-	200	-
7.1(DIMENSIONS AND TOLERANCES - Nominal Thickness)	-	-	-
7.2(DIMENSIONS AND TOLERANCES - Nominal Length and Width)	-	-	-
7.3.1 & 7.3.2 & 7.3.3(DIMENSIONS AND TOLE+I7RANCES - 1.Tolerance on Thickness 2.Tolerance on Leng+I58th & Width 3. Tolerance on shape )	-	-	-
8.2 Table -1(Tests -Bending Strenth Test)	-	-	-
8.3(Tests- Thickness)	-	-	-
8.4 and 8.5 & 7.3.3.1 & 7.3.3.2(Tests- 1.Straigthness of edges 2.Squareness of edges)	-	-	-
8.6(Density)	-	-	-
11.1(Marking- Each sheet shall be stamped or marked by any suitable method on the surface not exposed to the weather with the following information:)	-	-	-
11.2(Standard Mark.)	-	-	-

31 Dec, 2029

-
Included w.e.f. 15.04.2024

10843

RTRC LIMITED, GURUGRAM

9177406

IS 1554 : Part 2 (1988)

Specification for pvc insulated (Heavy Duty) electric cables: Part 2 for working voltages from 3.3 kV up to and including 11 kV (Second Revision)

190000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(CONDUCTOR)	-	0	Additional Charges, Rs 1500/- for each additional core. Additional Charges for FR-LSH/FR test as applicable
3.1.1(CONDUCTOR)	-	0	-
4.1(INSULATION)	-	0	-
5.1(SCREENING)	-	0	-
5.1.1(Non-magnetic Metallic Tape for SingleCore Unscreened and Unarmoured Cables)	-	0	-
6.1(FILLERS AND INNER SHEATH)	-	0	-
6.2(FILLERS AND INNER SHEATH)	-	0	-
7.1(ARMOURING)	-	0	-
7.2(ARMOURING)	-	0	-
8.1(OUTER SHEATH)	-	0	-
9.1(CONDUCTOR)	-	0	-
9.2(CONDUCTOR)	-	0	-
10.1(CONDUCTOR SCREENING)	-	0	-
11.1(INSULATION)	-	0	Additional Charge, Rs 25000/- for each additional Core
11.2(INSULATION : Thickness of Insulation)	-	1500	-
11.3(INSULATION : Tolerance on Thickness of Insulation)	-	0	-
11.4(INSULATION : Application of Insulation)	-	0	-
12.1(INSULATION SCREENING)	-	0	-
12.2(INSULATION SCREENING)	-	0	-
12.3(INSULATION SCREENING)	-	0	-
12.4(INSULATION SCREENING)	-	0	-
13.1(CORE IDENTIFICATION)	-	0	-
13.1.1(CORE IDENTIFICATION)	-	0	-
14.1(LAYING UP OF CORES)	-	0	-
15.1(INNER SHEATH (COMMON COVERING))	-	500	-
15.2(INNER SHEATH (COMMON COVERING))	-	0	-
15.3(INNER SHEATH (COMMON COVERING))	-	0	-
15.4(INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-	500	-
15.4.1(INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-	0	-
16.1.1(ARMOURING : Application)	-	0	-
16.1.2(ARMOURING : Application)	-	0	-
16.1.3(ARMOURING : Direction of lay )	-	0	-
16.1.4(ARMOURING : Application)	-	1500	-
16.2.1(ARMOURING : Type of Armour)	-	0	-
16.2.2(ARMOURING : Type of Armour)	-	0	-
13.6 g)(ARMOURING: Resistivity)	-	1000	-
17.1(OUTER SHEATH)	-	0	-
17.2(OUTER SHEATH : colour )	-	500	-
17.3.1(Thickness of Outer Sheath : Unarmoured Cables)	-	1500	-
17.3.2(Thickness of Outer Sheath : Armoured Cables)	-	1500	-
18.1 a) 1)(Tests on Conductor : Annealing test (for copper))	-	1000	AS APPLICABLE
18.1 a) 2)(Tensile test (for aluminium) - Before stranding )	-	0	AS APPLICABLE
18.1 a) 2)(Tensile test (for aluminium) - After stranding )	-	0	AS APPLICABLE
18.1 a) 3)(Tests on Conductor : Wrapping test ( for aluminium))	-	0	-
18.1 a)4)(Tests on conductor : Conductor resistance test - Main conductor )	-	3500	-
18.1 a)4)(Resistance test - Neutral conductor )	-	0	-
18.1 d) 1)(Phyaical tests for insulation : Tensile Test)	-	1000	-
18.1 d) 1)(Phyaical tests for insulation : Elongation )	-	1000	-
18.1 d) 1)(Physical tests for sheath : Tensile stregth )	-	1000	-
18.1 d) 1)(Physical tests for sheath : Elongation )	-	1000	-
18.1 d) 2)(Phyaical tests for insulation- Ageing in air Oven : Tensile Test)	-	2500	-
18.1 d) 2)(Phyaical tests for insulation - Ageing in air oven : Elongation )	-	2500	-
18.1 d) 2)(Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	2500	-
18.1 d) 2)(Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	2500	-
18.1 d) 2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	0	-
18.1 d) 2)(Physical tests for outer sheath -Ageing in air oven : Elongation )	-	0	-
18.1 d) 2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	0	-
18.1 d) 2)(Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	2500	-
18.1 d) 3)(Phyaical tests for insulation : Shrinkage )	-	2500	-
18.1 d) 3)(Phyaical tests for insulation : Shrinkage - Crack observed )	-	0	-
18.1 d) 5)( Loss of mass in air oven- sheath )	-	5000	-
18.1 d) 6)(Heat shock test- Insulation )	-	2000	-
18.1 d) 6)(Heat shock test- sheath )	-	2000	-
18.1 d) 7)(Thermal stability- insulation )	-	1000	-
18.1 d) 7)(Thermal stability- Sheath )	-	1000	-
18.1 d) 8)(Water absorption (gravimetric)(for insulation, where applicable))	-	5500	-
18.1 e)(Insulation resistance test : Volume Resistivity )	-	0	-
18.1 e)(Insulation resistance test : IR Constant )	-	2500	-
19.2(Partial discharge test)	-	22000	-
19.3(Bending test)	-	5000	-
19.4(Dielectric power factor test)	-	0	-
19.4(Dielectric power factor test)	-	15000	-
19.5(Heating cycle test)	-	35000	-
19.6(Impulse withstand test)	-	18000	-
19.7(High voltage test)	-	9000	-
19.8(Flammability test)	-	3500	-
19.9(Oxygen Index Test)	-	2500	-
19.10(Flame Retardance Test on Single Cables)	-	3000	-
18.1 d) 3)(Phyaical tests for Sheath : Shrinkage )	-	2500	-
18.1 d) 3)(Phyaical tests for Sheath : Shrinkage - Crack observed )	-	2500	-
18.1 d) 4)(Hot deformation : Insulation )	-	2500	-
18.1 d) 4)(Hot deformation : Sheath )	-	2500	-
18.1 d) 5)( Loss of mass in air oven- Insulation )	-	5000	-
19.11(Flame Retardance Test on Bunched Cables)	-	0	Additional Charge, if applicable
19.13(Test for Halogen Acid Gas Evolution)	-	0	Additional Charge, if applicable
19.14(Temperature Index)	-	0	Additional Charge, if applicable
18.4(Optional Test : Cold Impact )	-	1500	-
20.1(IDENTIFICATION : Manufacturer's Identification)	-	0	-
20.2(IDENTIFICATION : Cable Identification)	-	0	-
20.3(IDENTIFICATION : Cable Code)	-	0	-
16.3(Armouring : Dimensions -Wire Diameter)	-	1500	-
16.3(Armouring : Dimensions -Formed wire )	-	1500	-
16.4(ARMOURING : Joints)	-	0	-
16.5(ARMOURING : Resistance)	-	1000	-
13.6 a)(ARMOURING: Tensile Strength)	-	1000	-
13.6 b)(ARMOURING: Elongation )	-	0	-
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	1000	-
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	500	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	1000	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	2500	-

03 Apr, 2027

-
Included w.e.f. 24.04.2024

10844

Alpha Test House Services LLP (160), Sahibzada Ajit Singh Nagar

9138706

IS 459 (1992)

Corrugated and semi - Corrugated asbestos cement sheets - Specification (Third Revision)

Corrugated and semi - Corrugated asbestos cement sheet

16500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5, Table 1(Dimensions & Tolerances - Type of Sheet - cl. 5)	-	1000	-
5, Table 1, Figure 1,2(Dimensions & Tolerances - Depth of Corrugation, D - Cl. 5)	-	1000	-
5, Table 1, Figure 1,2(Dimensions & Tolerances - Pitch of Corrugation, P - Cl. 5)	-	600	-
5, Table 1, Figure 1,2(Dimensions & Tolerances - Overall width, B - Cl. 5)	-	600	-
5, Table 1, Figure 1,2(Dimensions & Tolerances - Effective Width, C - Cl. 5)	-	600	-
5, Table 1, Figure 1,2(Dimensions & Tolerances - Nominal Thickness, T - Cl. 5)	-	600	-
5, Table 1, Figure 1,2(Dimensions & Tolerances - Length of Sheet, A - Cl. 5)	-	600	-
6.1(Load Bearing Capacity Test - Cl. 6.1, IS 5913)	-	6800	-
7(General Appearance and Finish - Cl. 7.1)	-	500	-
7(General Appearance and Finish - Cl. 7.2)	-	1000	-
12(Marking - Indication of source of manufacture - Cl. 12)	-	200	-
12(Marking - Year & Date of manufacture - Cl. 12)	-	200	-
12(Marking - Pictorial warning signs as given in IS 12081 (Part 2) : 1987 - Cl. 12)	-	300	-
5, Table 1(Dimensions & Tolerances - Type of Sheet - cl. 5)	-	1000	-
5, Table 1, Figure 1,2(Dimensions & Tolerances - Depth of Corrugation, D - Cl. 5)	-	1000	-
5, Table 1, Figure 1,2(Dimensions & Tolerances - Pitch of Corrugation, P - Cl. 5)	-	600	-
5, Table 1, Figure 1,2(Dimensions & Tolerances - Overall width, B - Cl. 5)	-	600	-
5, Table 1, Figure 1,2(Dimensions & Tolerances - Effective Width, C - Cl. 5)	-	600	-
5, Table 1, Figure 1,2(Dimensions & Tolerances - Nominal Thickness, T - Cl. 5)	-	600	-
5, Table 1, Figure 1,2(Dimensions & Tolerances - Length of Sheet, A - Cl. 5)	-	600	-
6.1(Load Bearing Capacity Test - Cl. 6.1, IS 5913)	-	6800	-
7(General Appearance and Finish - Cl. 7.1)	-	500	-
7(General Appearance and Finish - Cl. 7.2)	-	1000	-
12(Marking - Indication of source of manufacture - Cl. 12)	-	200	-
12(Marking - Year & Date of manufacture - Cl. 12)	-	200	-
12(Marking - Pictorial warning signs as given in IS 12081 (Part 2) : 1987 - Cl. 12)	-	300	-
6.2(Impermeability)	-	1000	-
6.3(Frost Cracking)	-	1000	-
6.4(Density)	-	500	-

31 Dec, 2029

-
Included w.e.f. 15.04.2024

10845

RTRC LIMITED, GURUGRAM

9177406

IS 16246 (2015)

Elastomer insulated cables with limited circuit integrity when affected by fire - Specification

101500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 19.4( Cable Code)	-	0	Additional Charges, Rs 1500/- for each additional core.
Cl 19.3( Cable Identification)	-	0	-
Cl 19.2( Voltage Identification)	-	0	-
Cl.4.1( Cables for Fixed Installation)	-	0	-
Cl.5( INSULATION)	-	0	-
Cl. 6.1( Glass Tape)	-	0	-
Cl 6.2( Polyethylene Teraphthalate (PETP) or Polypropylene base Tape)	-	0	-
Cl 6.4( Fire Barrier Tape)	-	0	-
Cl 7(CENTRE AND FILLERS)	-	0	-
Cl 7(CENTRE AND FILLERS)	-	0	-
Cl 7(CENTRE AND FILLERS)	-	0	-
Cl 7(CENTRE AND FILLERS)	-	0	-
Cl 8( ARMOUR)	-	0	-
Cl 9.1( Inner Sheath)	-	0	-
Cl 9.2( Outer Sheath)	-	0	-
Cl 10.1( CONDUCTORS)	-	1000	-
Cl 10.2( CONDUCTORS)	-	0	-
Cl 11.1( INSULATION)	-	0	-
Cl 19.1( Manufacturer’s Identification)	-	0	-
Cl 18.4.2(Flame Retardence Test on Bunched Cables IS 10810 : Part 63)	-	14500	-
Cl 18.3 Annex B of IS 16246( Circuit Integrity Test Under Fire Condition)	-	0	-
Cl 18.4.1( Flame Retardence Test on Single Cable IS 10810 : Part 61)	-	3000	-
Cl 15.4.2( ARMOURING)	-	0	-
Cl 15.4.2( ARMOURING)	-	0	-
Cl 15.4.2( ARMOURING)	-	0	-
Cl 15.4.2( ARMOURING)	-	0	-
Cl 15.4.2( ARMOURING)	-	0	-
Cl 15.4.2( ARMOURING)	-	0	-
Cl 15.4.2( ARMOURING)	-	0	-
Cl 16.2( OUTER SHEATH)	-	0	-
Cl 16.3( Thickness of Outer Sheath - Avg IS 10810 : Part 6)	-	500	-
Cl 16.3( Thickness of Outer Sheath - Minimum IS 10810 : Part 6)	-	500	-
Cl 11.2(Thickness of Insulation IS 10810 : Part 6)	-	500	-
Cl 12( CORE IDENTIFICATION)	-	0	-
Cl 13( LAYING UP OF CORES)	-	0	-
Cl 14.2( Thickness of Inner Sheath IS 10810 : Part 6)	-	500	-
Cl 15.1( ARMOURING)	-	0	-
Cl 15.3.1( Type of Armour)	-	0	-
Cl 15.3.2( Type of Armour)	-	0	-
Cl 15.3.3( ARMOURING)	-	0	-
Cl 15.3.3( ARMOURING)	-	0	-
Cl 15.4.1( ARMOURING)	-	0	-
Cl 17.2(Annealing test (for copper) IS 10810 : Part 1)	-	1000	-
Cl 17.2(Conductor resistance test IS 10810 : Part 5)	-	1000	-
Cl 17.1(Persulphate test (tinned copper conductor) IS 10810 : Part 4)	-	1000	-
Cl 17.2(Tensile strength before ageing on insulation IS 10810 : Part 7)	-	2000	as applicable
Cl 17.2(elongation at break before ageing on insulation IS 10810 : Part 7)	-	2000	-
Cl 17.2(Tensile strength after Ageing in air bomb IS 10810 : Part 56)	-	2000	-
Cl 17.2(Elongation after Ageing in air bomb IS 10810 : Part 56)	-	2000	-
Cl 17.2(Tensile strength variation)	-	0	-
Cl 17.2(Elongation Variation)	-	0	-
Cl 17.2(Hot set elongation on insulation IS 10810 : Part 30)	-	1500	-
Cl 17.2(Permanent elongation (set) on insulation IS 10810 : Part 30)	-	0	-
Cl 17.1(Tensile strength before ageing on sheath IS 10810 : Part 7)	-	2000	-
Cl 17.1(elongation at break before ageing on sheath IS 10810 : Part 7)	-	2000	-
Cl 17.1(Hot set elongation test on sheath IS 10810 : Part 30)	-	1500	-
Cl 17.1(Permanent elongation (set) test on sheath IS 10810 : Part 30)	-	0	-
Cl 17.1(Oxygen index test on sheath IS 10810 : Part 58)	-	2500	-
Cl 17.1(Temperature index test on sheath IS 10810 : Part 64)	-	2500	-
Cl 17.1(Acid gas generation on sheath IS 10810 : Part 39)	-	5000	-
Cl 17.2(Insulation resistance test IS 10810 : Part 43)	-	2500	-
Cl 17.1(Water absorption test (for insulation) IS 10810 : Part 28)	-	14500	-
Cl 18.2(High Voltage Test IS 10810 : Part 45)	-	2500	-
Cl 18.2(High Voltage Test IS 10810 : Part 45)	-	2500	-
Cl 18.3 Annex B of IS 16246( Circuit Integrity Test Under Fire Condition)	-	35000	as applicable

03 Apr, 2027

-
Included w.e.f. 24.04.2024

10846

Alpha Test House Services LLP (160), Sahibzada Ajit Singh Nagar

9138706

IS 7534 (1985)

Specificaiton for sliding locking bolts for use with padlocks

110,150,200,250,300 MM

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1 table 2(DIMENSIONS OF LOCKING BOLT)	-	3000	-
5.1 table 2(1. The locking bolts shall have smooth sliding action. 2. All sharp edges and corners shall be removed and finished smooth. 3. All screw holes shall be countersunk to suit the countersunk head wood screws)	-	1000	-
7.1(Mild steel locking bolts copper oxidized)	-	1000	-
7.1(Mild steel locking bolts Electrogalvanised)	-	1000	-
7.1(Aluminium alloy bolt anodized)	-	1500	-
7.1(Anodic Coatic)	-	1500	-
5.1.1(Bolt Plate)	-	500	-
5.1.2(Bolt)	-	500	-
4(Mild steel sheet, Aluminium alloy sheet)	-	10000	-

31 Dec, 2029

-
Included w.e.f. 12.04.2024

10847

Bharat Test House Pvt. Ltd. 1668 Sonipat

9168306

IS 7506 (1987)

Specification for nickel powder (First Revision)

6800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2(Supply of Material)	-	100	5% discount for BIS
3(Chemical Composition)	-	5500	5% discount for BIS
3.2(Hydrogen loss)	-	500	5% discount for BIS
4(Average Particle Size)	-	500	5% discount for BIS
6(Packing)	-	100	5% discount for BIS
7(Marking)	-	100	5% discount for BIS
2(Supply of Material)	-	-	-
3(Chemical Composition)	-	-	-
3.2(Hydrogen loss)	-	-	-
4(Average Particle Size)	-	-	-
6(Packing)	-	-	-
7(Marking)	-	-	-

26 Jul, 2027

-
-

10848

Adityapur Auto Cluster, Adityapur

5178506

IS 2830 (2012)

Carbon steel cast billet ingots, billets, blooms and slabs for re-rolling into steel for general structural purposes - Specification (Third Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 9(Workmanship)	-	12000	-
Cl 10.1(Workmanship)	-	12000	-
Cl 10.2(Workmanship)	-	12000	-
Cl 10.2(Press)	-	12000	-
Cl 10.3(Workmanship)	-	12000	-
Cl 11(Length, Width & Thickness)	-	12000	-
Cl 9(Workmanship)	-	12000	-
Cl 10.1.a)(Workmanship)	-	12000	-
Cl 10.1.b)(Workmanship)	-	12000	-
Cl 10.2(Press)	-	12000	-
Cl 10.3(Workmanship)	-	12000	-
Cl 11(Length, Width & Thickness)	-	12000	-
Cl 9(Workmanship)	-	12000	-
Cl 10.1(Workmanship)	-	12000	-
Cl 10.2(Workmanship)	-	12000	-
Cl 10.2(Press)	-	12000	-
Cl 10.3(Workmanship)	-	12000	-
Cl 11(Length)	-	12000	-
6.1(Carbon %)	-	12000	-
6.1(Manganese %)	-	12000	-
6.1(Phosphorus %)	-	12000	-
6.1(Sulphur %)	-	12000	-
6.1(Silicon %)	-	12000	-
6.1( Copper %)	-	12000	-
6.1( Aluminium %)	-	12000	-
6.1( Nb)	-	12000	-
6.1(V)	-	12000	-
6.1( Ti)	-	12000	-
6.1(Cr)	-	12000	-
6.1(Mo)	-	12000	-
6.1(Ni)	-	12000	-
6.1( Nitrogen%)	-	12000	-
6.1(Carbon %)	-	12000	-
6.1(Manganese %)	-	12000	-
6.1(Phosphorus %)	-	12000	-
6.1(Sulphur %)	-	12000	-
6.1(Silicon %)	-	12000	-
6.1( Copper %)	-	12000	-
6.1( Aluminium %)	-	12000	-
6.1( Nb)	-	12000	-
6.1(V)	-	12000	-
6.1( Ti)	-	12000	-
6.1(Cr)	-	12000	-
6.1(Mo)	-	12000	-
6.1(Ni)	-	12000	-
6.1( Nitrogen%)	-	12000	-
6.1(Carbon %)	-	12000	-
6.1(Manganese %)	-	12000	-
6.1(Phosphorus %)	-	12000	-
6.1(Sulphur %)	-	12000	-
6.1(Silicon %)	-	12000	-
6.1( Copper %)	-	12000	-
6.1( Aluminium %)	-	12000	-
6.1( Nb)	-	12000	-
6.1(V)	-	12000	-
6.1( Ti)	-	12000	-
6.1(Cr)	-	12000	-
6.1(Mo)	-	12000	-
6.1(Ni)	-	12000	-
6.1(Nitrogen%)	-	12000	-
11(Thickness)	-	12000	-
11(Width)	-	12000	-
10.1 (a)(Macro-examination)	-	12000	-
10.1 (b)(Sulphur print)	-	12000	-
Clause 6.1(IS 2830 : 2012)	-	12000	-
Cl. 10.1 (b)(Sulphur Print)	-	12000	-
Cl. 11.2(Out of Squareness)	-	12000	-
Cl. 10.3(Camber)	-	12000	-
Cl. 10.2(Bend)	-	12000	-
Cl. 10.1 (a)(Macro Examination)	-	12000	-
Clause 10.3(Camber)	-	12000	-
Clause 10.2(Bend)	-	12000	-
Cl 11(Length, Width & Thickness)	-	12000	-
Cl 10.3(Workmanship)	-	12000	-
Cl 10.2(Press)	-	12000	-
Cl 10.2(Workmanship)	-	12000	-
Cl 10.1(Workmanship)	-	12000	-
Cl 9(Workmanship)	-	12000	-
Cl 9(Workmanship)	-	12000	-
Cl 10.1(Workmanship)	-	12000	-
Cl 10.2(Workmanship)	-	12000	-
Cl 10.2(Press)	-	12000	-
Cl 10.3(Workmanship)	-	12000	-
Cl 11(Length, Width & Thickness)	-	12000	-
Clause 6, Table 1 Note : 1(By Calculation)	-	12000	-
Clause 6, Table 1 Note : 3(By Calculation)	-	12000	-
6(Carbon as C - IS:228)	-	12000	-
6(Manganese as Mn-IS:228)	-	12000	-
6(Sulphur as S- IS:228)	-	12000	-
6(carbon equivalent (CE))	-	12000	-
6(Micro alloying elements)	-	12000	-
6(Sulphur + Phosphorus)	-	12000	-
6(Copper as Cu)	-	12000	-
10 (a)(Macro Examination-IS:11371)	-	12000	-
10 (b)(Sulphur Print Test - IS:12037)	-	12000	-
8(Selection of Test samples)	-	12000	-
12(Tolerance - IS 2830)	-	12000	-
13(Marking)	-	12000	-
Clause 6, Table 1 Note : 1(Carbon Equivalent)	-	12000	-
Clause 6, Table 1 Note : 3(Nb+V+Ti)	-	12000	-
Clause 6, Table 1 Note : 9(S+P)	-	12000	-
Clause 9(Freedom from Defect)	-	12000	-
4(Supply of material)	-	12000	-
5(Manufacture)	-	12000	-
6.1(Chemical method)	-	12000	-
6.2(Copper bearing quality)	-	12000	-
6.3(Check Analysis)	-	12000	-
10.1(Test)	-	12000	-
10.2(Bend)	-	12000	-
10.3(Chamber)	-	12000	-
11(Dimensions)	-	12000	-
12(Tolrences)	-	12000	-
13(Marking)	-	12000	-

28 Jun, 2027

-
-

10849

Delhi Test House (A Unit of Delhii Test House Global LLP) (50) Kundli, Sonipat

9127026

IS 14155 (1994)

Domestic electric clothes washing machines for household use - Specification

190000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
18(Finish)	-	2000.00	-
17(Endurance)	-	5000.00	-
16(Determination of mechanical detergent loss in the sump of washing machine)	-	5000.00	-
15(Determination of water and energy consumption)	-	5000.00	-
14(Determination of the water extraction efficiency)	-	5000.00	-
13(Determination of water retention percentage (Rinsing efficiency))	-	5000.00	-
12(Determination of wear suffered by textile)	-	4000.00	-
11(Determination of the washing performance standard measurement with a load of clean material and standardized soiling)	-	94000.00	-
Cl.9 (Cl.8 to Cl.32 of IS 302-2-7)(Safety requirement)	-	48000.00	-
Cl.9 (Cl.24 of IS 302-2-7)(Component)	-	2000.00	-
Cl.9 (Cl.8 to Cl.32 of IS 302-2-7)(Safety requirement for Washing machine)	-	10000	-
9.1(Spin Extractor safety requirement)	-	5000.00	-
18(Finish)	-	2000.00	-
17(Endurance)	-	5000.00	-
16(Determination of mechanical detergent loss in the sump of washing machine)	-	5000.00	-
15(Determination of water and energy consumption)	-	5000.00	-
14(Determination of the water extraction efficiency)	-	5000.00	-
13(Determination of water retention percentage (Rinsing efficiency))	-	5000.00	-
12(Determination of wear suffered by textile)	-	4000.00	-
11(Determination of the washing performance standard measurement with a load of clean material and standardized soiling)	-	94000	-
Cl.9 (Cl.8 to Cl.32 of IS 302-2-7)(Safety requirement)	-	48000	-
Cl.9 (Cl.24 of IS 302-2-7)(Component)	-	2000.00	-
Cl.9 (Cl.8 to Cl.32 of IS 302-2-7)(Safety requirement for Washing machine)	-	10000.00	-
9.1(Spin Extractor safety requirement)	-	5000.00	-

23 Jun, 2028

-
Included w.e.f. 03.05.2024

10850

RTRC LIMITED, GURUGRAM

9177406

IS 694 (2010)

Polyvinyl chloride insulated unsheathed and sheathed cables/cords with rigid and flexible conductor for rated voltages up to and including 450/750 v (Fourth Revision)

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
13(Cable code)	-	0	Additional charge, Rs. 1000 /- For each additional core, Additional Charges for FR-LSH/FR test as applicable
11.2(Legibility)	-	250	-
11.1(Durability)	-	250	-
11(Identification)	-	1000	Additional charge, Rs. 1000 /- For each additional core
10.9(Additional ageing test (OU cables only) -HV test (at 60±3oC))	-	5000	Additional charge, If applicable
10.4(Flammability test- Unaffected portion)	-	0	-
10.4(Flammability test-Burning after flame removal)	-	500	-
table 1 e) 3) (IR constant- max. Temp)	-	250	-
table 1 e) 3) (IR constant- Room temp )	-	250	-
table 1 e) 3) (Volume Resistivity - Maximum temp)	-	250	-
table 1 e) 3) (Volume Resistivity - Room temp )	-	250	-
10.2(HV (room temperature))	-	1000	-
10.1(HV (water immersion))	-	1000	-
10.1(HV (water immersion))	-	5500	(d.c. high voltage test)
10.8(Smoke density rating)	-	3500	Additional charge, If applicable
10.6(Halogen evolution)	-	3500	Additional charge, If applicable
10.7(Temperature index)	-	2500	Additional charge, If applicable
10.5(Oxygen index)	-	2500	Additional charge, If applicable
Table 1 iii) d) 9)(Cold impact for sheath)	-	1250	Additional charge, If applicable
Table 1 iii) d) 8)(Cold bend for sheath)	-	1250	Additional charge, If applicable
Table 1 iii) c) 9)(Cold impact for insulation)	-	1250	Additional charge, If applicable
Table 1 iii) c) 8)(Cold bend for insulation)	-	1250	Additional charge, If applicable
Table 1(Category Code)	-	0	-
Table 1 iii) d) 7)(Thermal stability- Sheath )	-	1000	Additional charge, If applicable
Table 1 iii) c) 7)(Thermal stability- Insulation )	-	1000	-
Table 1 iii) d) 6)(Hot deformation -Indentation depth - Sheath )	-	1000	Additional charge, If applicable
Table 1 iii) c) 6)(Hot deformation - Indentation depth- Insulation)	-	1000	-
Table 1 iii) d) 5)(Heat shock-Sheath )	-	750	Additional charge, If applicable
Table 1 iii) c) 5)(Heat shock-Insulation )	-	750	-
Table 1 iii) d) 4)(Cracks Observed)	-	0	-
Table 1 iii) d) 4)(Shrinkage- Sheath )	-	1000	Additional charge, If applicable
Table 1 iii) c) 4)(Cracks Observed)	-	0	-
Table 1 iii) c) 4)(Shrinkage-Insulation)	-	1000	-
Table 1 iii) d) 2)(Loss of mass- Sheath )	-	4500	Additional charge, If applicable
Table 1 iii) c) 2)(Loss of mass- Insulation )	-	4500	-
22(TWO AND THREE CORE FLAT CABLES WITH PVC INSULATION AND SHEATHED (CLASS 2 OR 5) FOR GENERAL PURPOSE( FOR MAXIMUM CONDUCTOR TEMPERA TURE 70°C OR 85°C))	-	0	-
21(ARALLEL TWIN AND TWISTED TWIN FLEXIBLE PVC INSULATED UNSHEATHED CORDS (CLASS 5) FOR GENERAL PURPOSE (FOR MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C))	-	0	-
20(MULTICORE CIRCULAR PVC INSULATED AND SHEATHED CABLES WITH FLEXIBLE CONDUCTOR (CLASS 5) FOR GENERAL PURPOSE (FOR MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C))	-	0	-
19(SINGLE AND MULTICORE CIRCULAR PVC INSULATED AND SHEATHED CABLES/CORDS WITH FLEXIBLE CONDUCTOR (CLASS 5) FOR GENERAL PURPOSE (MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C))	-	0	-
Table 1 iii) d) 3)(Sheath- Elongation variation)	-	500	Additional charge, If applicable
Table 1 iii) d) 3)(Sheath- TS variation)	-	500	Additional charge, If applicable
Table 1 iii) d) 3)(Sheath- Elongation (After ageing))	-	500	Additional charge, If applicable
Table 1 iii) d) 3)(Sheath- Tensile strength (After ageing))	-	500	Additional charge, If applicable
Table 1 iii) d) 1)(Sheath- Elongation (Without ageing))	-	500	Additional charge, If applicable
Table 1 iii) d) 1)(Sheath -Tensile strength (Without ageing))	-	500	Additional charge, If applicable
18(SINGLE AND MULTICORE CIRCULAR PVC INSULATED AND SHEATHED CABLES WITH RIGID CONDUCTOR (CLASS 1 AND CLASS 2) FOR GENERAL PURPOSE ) FOR MAXIMUM CONDUCTOR TEMPERATURE (70°C OR 85°C))	-	500	Additional charge, If applicable
17(SINGLE CORE NON-SHEATHED CABLES WITH FLEXIBLE CONDUCTOR FOR GENERAL PURPOSE (MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C))	-	0	-
16.2(Tests)	-	0	-
16.1(Construction)	-	0	-
15(PACKING AND MARKING)	-	0	-
13(CABLE CODE)	-	0	-
12(CORE IDENTIFICATION)	-	0	-
11(IDENTIFICATION)	-	1000	Additional charge, Rs. 1000 /- For each additional core
10.11(Persulphate Test)	-	1000	Additional charge, Rs. 1000 /- For each additional core
10.1(Flex Test)	-	0	-
10.9(Additional Ageing Test (for Cables for Outdoor Use)	-	0	-
10.8(Smoke Density Rating)	-	3500	Additional charge, Rs. 1000 /- For each additional core
Table 1 iii) c) 3)(Elongation variation)	-	500	-
Table 1 iii) c) 3)(TS variation)	-	500	-
Table 1 iii) c) 3)(Elongation (After ageing))	-	500	-
Table 1 iii) c) 3)(Tensile strength (After ageing))	-	500	-
Table 1 iii) c) 1)(Elongation (Without ageing))	-	500	-
Table 1 iii) c) 1)(Tensile strength (Without ageing))	-	500	-
(Cl. 18.1.4) (Cl. 19.1.5) (Cl. 20.1.4) (Cl. 22.1.4)(Colour of Sheath)	-	0	-
8.3(Thickness of Sheath)	-	500	Table 1 iii) c) 3) (TS variation)
5.2(Application )	-	0	-
10.7(Test for Temperature Index)	-	0	-
10.6(Test for Halogen Acid Gas Evolution)	-	0	-
10.5(Oxygen Index Test)	-	0	-
10.4(Flammability Test)	-	0	-
10.3(Spark Test)	-	2500	Additional charge, If applicable
10.2(High Voltage Test (at Room Temperature))	-	0	-
10.1(High Voltage Test (Water Immersion Test))	-	0	-
9(OVERALL DIMENSIONS)	-	500	-
8(SHEATH)	-	0	-
7(BINDER TAPE)	-	0	-
6(FILLER)	-	0	-
5(INSULATION)	-	0	-
4.2(Electrical Resistance)	-	0	-
4.1(Material)	-	0	-
10.3(Spark Test)	-	2500	Additional charge, If applicable
5.4(Mechanical properties before and after ageing)	-	0	-
table 1, 4.2(insulation resistance test)	-	0	-
10.3(Spark test)	-	2500	Additional charge, If applicable
Table 4(Copper purity test)	-	9000	Additional charge, If applicable
5.3(Avarage thickness of insulation)	-	0	-
5.3(Thickness of Insulation)	-	500	-
9.1(Ovality)	-	0	-
9(Overall dimensions)	-	500	-
10.11(Per sulphate test (for tinned Cu cable only))	-	1000	Additional charge, If applicable
4.2(Conductor resistance test)	-	1000	-
4.1(Wrapping test (for Al))	-	500	-
4.1(Tensile test (for Al)- After Stranding)	-	500	-
4.1(Tensile test (for Al)-Before Stranding)	-	500	-
4.1(Annealing test (for copper))	-	750	-
(Cl.6.1.3 of IS 8130:2013)(Flexible Conductors (Classes 5))	-	0	-
5.3(Minimum thickness of insulation)	-	500	-
8.3(Avarage thickness of Sheath)	-	0	-
8.3(Minimum thickness of Sheath)	-	500	Additional charge, If applicable
Table 2, IS 8130(No fo wire in a conductor)	-	0	-
4, IS 8130(Construction of conductor)	-	0	-
12.0(Core identification)	-	0	-
10.11(Persulphate Test )	-	1000	-
4.1(Conductor - Material)	-	0	-
4.1(Conductor - Material)	-	0	-
4.4(Joints in Conductor)	-	0	-
4.4(Joints in Conductor)	-	0	-
(Cl.6.1.3 of IS 8130:2013)( Flexible Conductors (Classes 5))	-	0	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors(Class-2))	-	0	-
(Cl.6.1.3 of IS 8130:2013)(Stranded compacted circular conductors and shaped conductors (Class 2))	-	0	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors (Class-2))	-	0	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors (Class-2))	-	0	-
5.1(Insulation)	-	0	-
6.1(Filler)	-	0	-
6.2(Filler)	-	0	-
7(Binder Tape)	-	0	-
8.1(Sheath Material )	-	0	-
(Cl.6.1.3 of IS 8130:2013)(Solid Conductor (Class 1))	-	0	-
(Cl.6.1 of IS 8130:2013)(Solid Conductor (Class 1))	-	0	-
(Cl.6.1 of IS 8130:2013)(Solid Conductor (Class 1))	-	0	-
(Cl.16.1) (Cl.19.1)(Conductor- Diameter )	-	500	-
(Cl.16.1) (Cl.19.1)(Conductor)	-	0	-
12(CONSTRUCTION Core Identification)	-	0	-
(Cl. 18.1.3) (Cl. 19.1.4) (Cl. 20.1.3) (Cl. 21.1.3) (Cl. 22.1.3)(Assembly of cores )	-	0	-
(Cl.16.1) (Cl.19.1)(Conductor)	-	0	-
(Cl.16.1) (Cl.19.1)(Conductor)	-	0	-

03 Apr, 2027

-
Included w.e.f. 24.04.2024

10851

RTRC LIMITED, GURUGRAM

9177406

IS 8130 (2013)

Conductors for insulated electric cables and flexible cords - Specification (Second Revision)

cable

9500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Aluminium)	-	0	-
4.1(Aluminium)	-	0	-
4.2(Copper)	-	0	-
4.3(Form of Conductor)	-	0	-
4.4(Joints in Conductor)	-	0	-
5(Classification)	-	0	-
6(Construction)	-	0	-
7.1(Tests for Copper Conductors)	-	3500	(Diameter of wire, Annealing test, Flexibility class) - As applicable
7.2(Tests for Aluminium Conductors)	-	4500	(Diameter of wire, Tensile test, Wrapping test, Flexibility class) - As applicable
7.3(Resistance Test)	-	1500	-
8(Packing and Marking)	-	0	-
4.1(Aluminium)	-	0	-
4.1(Aluminium)	-	0	-
4.2(Copper)	-	0	-
4.3(Form of Conductor)	-	0	-
4.4(Joints in Conductor)	-	0	-
5(Classification)	-	0	-
6(Construction)	-	0	-
7.1(Tests for Copper Conductors)	-	3500	(Diameter of wire, Annealing test, Flexibility class) - As applicable
7.2(Tests for Aluminium Conductors)	-	4500	(Diameter of wire, Tensile test, Wrapping test, Flexibility class) - As applicable
7.3(Resistance Test)	-	1500	-
8(Packing and Marking)	-	0	-
4.1(Aluminium)	-	0	-
4.1(Aluminium)	-	0	-
4.2(Copper)	-	0	-
4.3(Form of Conductor)	-	0	-
4.4(Joints in Conductor)	-	0	-
5(Classification)	-	0	-
6(Construction)	-	0	-
7.1(Tests for Copper Conductors)	-	3500	(Diameter of wire, Annealing test, Flexibility class) - As applicable
7.2(Tests for Aluminium Conductors)	-	4500	(Diameter of wire, Tensile test, Wrapping test, Flexibility class) - As applicable
7.3(Resistance Test)	-	1500	-
8(Packing and Marking)	-	0	-

03 Apr, 2027

-
Included w.e.f. 24.04.2024

10852

Intertek India Private Limited (Gujarat)

7166626

IS 14286 : Part 1 : Sec 1 (2019)

Terrestrial photovoltaic (PV) modules - Design qualification and type approval: Part 1 test requirements: Sec 1 special requirements for testing of crystalline silicon photovoltaic (Pv) modules (Second Revision)

1298050 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11.1(Visual inspection (MQT 01))	-	45500	-
11.2(Maximum power determination (MQT 02))	-	45000	-
11.3(Insulation test (MQT 03))	-	10000	-
11.4(Measurement of temperature coefficients (MQT 04))	-	65000	-
11.5(Measurement of nominal module operating temperature (NMOT) (MQT 05))	-	18200	-
11.6(Performance at STC and NMOT (MQT 06))	-	5000	-
11.7(Performance at low irradiance (MQT 07))	-	5000	-
11.8(Outdoor exposure test (MQT 08))	-	52200	-
11.9(Hot-spot endurance test (MQT 09))	-	36400	-
11.1(UV preconditioning test (MQT 10))	-	36400	-
11.11(Thermal cycling test (MQT 11))	-	400000	-
11.12(Humidity-freeze test (MQT 12))	-	118800	-
11.13(Damp heat test (MQT 13))	-	18000	-
11.14(Robustness of terminations (MQT 14))	-	45500	-
11.15(Wet leakage current test (MQT 15))	-	63800	-
11.16(Static mechanical load test (MQT 16))	-	18200	-
11.17(Hail test (MQT 17))	-	22750	-
11.18(Bypass diode thermal test (MQT 18))	-	42300	-
11.19(Stabilization (MQT 19))	-	250000	-
11.1(Visual inspection (MQT 01))	-	45500	-
11.2(Maximum power determination (MQT 02))	-	45000	-
11.3(Insulation test (MQT 03))	-	10000	-
11.4(Measurement of temperature coefficients (MQT 04))	-	65000	-
11.5(Measurement of nominal module operating temperature (NMOT) (MQT 05))	-	18200	-
11.6(Performance at STC and NMOT (MQT 06))	-	5000	-
11.7(Performance at low irradiance (MQT 07))	-	5000	-
11.8(Outdoor exposure test (MQT 08))	-	52200	-
11.9(Hot-spot endurance test (MQT 09))	-	36400	-
11.1(UV preconditioning test (MQT 10))	-	36400	-
11.11(Thermal cycling test (MQT 11))	-	400000	-
11.12(Humidity-freeze test (MQT 12))	-	118800	-
11.13(Damp heat test (MQT 13))	-	18000	-
11.14(Robustness of terminations (MQT 14))	-	45500	-
11.15(Wet leakage current test (MQT 15))	-	63800	-
11.16(Static mechanical load test (MQT 16))	-	18200	-
11.17(Hail test (MQT 17))	-	22750	-
11.18(Bypass diode thermal test (MQT 18))	-	42300	-
11.19(Stabilization (MQT 19))	-	250000	-
5(Marking and documentation)	-	0	-
8(Major visual defects)	-	0	-
5(Marking and documentation)	-	0	-
8(Major visual defects)	-	0	-
11.1(Visual inspection (MQT 01))	-	-	-
11.2(Maximum power determination (MQT 02))	-	-	-
11.3(Insulation test (MQT 03))	-	-	-
11.4(Measurement of temperature coefficients (MQT 04))	-	-	-
11.5(Measurement of nominal module operating temperature (NMOT) (MQT 05))	-	-	-
11.6(Performance at STC and NMOT (MQT 06))	-	-	-
11.7(Performance at low irradiance (MQT 07))	-	-	-
11.8(Outdoor exposure test (MQT 08))	-	-	-
11.9(Hot-spot endurance test (MQT 09))	-	-	-
11.1(UV preconditioning test (MQT 10))	-	-	-
11.11(Thermal cycling test (MQT 11))	-	-	-
11.12(Humidity-freeze test (MQT 12))	-	-	-
11.13(Damp heat test (MQT 13))	-	-	-
11.14(Robustness of terminations (MQT 14))	-	-	-
11.15(Wet leakage current test (MQT 15))	-	-	-
11.16(Static mechanical load test (MQT 16))	-	-	-
11.17(Hail test (MQT 17))	-	-	-
11.18(Bypass diode thermal test (MQT 18))	-	-	-
11.19(Stabilization (MQT 19))	-	-	-
5(Marking and documentation)	-	-	-
8(Major visual defects)	-	-	-

02 Dec, 2029

-
-

10853

Intertek India Private Limited (Gujarat)

7166626

IS/IEC 61730 : PART 2 (2016)

Photovoltaic (PV) module safety qualification: Part 2 requirements for testing (First Revision)

1834032 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

02 Dec, 2029

-
-

10854

Intertek India Private Limited (Gujarat)

7166626

IS/IEC 61730 : PART 1 (2016)

Photovoltaic (PV) Module Safety Qualification Part 1 Requirements for Construction ( First Revision )

500000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4 IS/IEC 61730-1(Classification, Application and Inteded Use)	-	15625	-
5, 5.1 IS/IEC 61730-1(Requirements for design and Construction)	-	15625	-
5.2(Marking and documentation)	-	15625	-
5.3.2 IS/IEC 61730-1(Internal Wiring)	-	15625	-
5.3.3 IS/IEC 61730-1(External Wirings and cables)	-	15625	-
5.3.4 IS/IEC 61730-1(Connectors)	-	15625	-
5.3.5 IS/IEC 61730-1(Junction Box for PV modules)	-	15625	-
5.3.6 IS/IEC 61730-1(Front sheet and back Sheet)	-	15625	-
5.3.7 IS/IEC 61730-1(Insulation Barrier)	-	15625	-
5.3.8 IS/IEC 61730-1(Electrical Connections)	-	15625	-
5.3.9 IS/IEC 61730-1(Encapsulants)	-	15625	-
5.3.10 IS/IEC 61730-1(Bypass Diodes)	-	15625	-
5.4, 5.4.1 IS/IEC 61730-1(Mechanical and Electromechanical connections)	-	15625	-
5.4.2 IS/IEC 61730-1(Screw Connctions)	-	15625	-
5.4.3 IS/IEC 61730-1(Rivets)	-	15625	-
5.4.4 IS/IEC 61730-1(Thread Cutting Screws)	-	15625	-
5.4.5 IS/IEC 61730-1(Form/Press/Tight/Fit)	-	15625	-
5.4.6 IS/IEC 61730-1(Connections by adhesives)	-	15625	-
5.4.7 IS/IEC 61730-1(Other Connections)	-	15625	-
5.5, 5.5.1 IS/IEC 61730-1(Materials)	-	15625	-
5.5.2.3.2 IS/IEC 61730-1(Endurance to Electrical Stress)	-	15625	-
5.5.2.3.3 IS/IEC 61730-1(Endurance to thermal stress-RTE (RTI) or TI)	-	15625	-
5.5.2.3.4 IS/IEC 61730-1(Polymeric Insulating materials used as external Parts)	-	15625	-
5.5.2.3.5 IS/IEC 61730-1(Polymeric Insulating Parts supporting live Parts)	-	15625	-
5.5.3, 5.5.3.1 IS/IEC 61730-1(Metallic materials)	-	15625	-
5.5.3.2 IS/IEC 61730-1(Current Carrying Parts)	-	15625	-
5.5.4 IS/IEC 61730-1(Adhesives)	-	15625	-
5.6, 5.6.1 IS/IEC 61730-1(Protection Agianst Electric Shock)	-	15625	-
5.6.2 IS/IEC 61730-1(Protection Agianst accessibility to hazardeous live parts)	-	15625	-
5.6.3 IS/IEC 61730-1(Insulation Coordination)	-	15625	-
5.6.3.4(Clearances and creepage distances)	-	15625	-
5.6.4 IS/IEC 61730-1(Distance through Insulation)	-	15625	-
4 IS/IEC 61730-1(Classification, Application and Inteded Use)	-	0	-
5, 5.1 IS/IEC 61730-1(Requirements for design and Construction)	-	0	-
5.2(Marking and documentation)	-	0	-
5.3.2 IS/IEC 61730-1(Internal Wiring)	-	0	-
5.3.3 IS/IEC 61730-1(External Wirings and cables)	-	0	-
5.3.4 IS/IEC 61730-1(Connectors)	-	0	-
5.3.5 IS/IEC 61730-1(Junction Box for PV modules)	-	0	-
5.3.6 IS/IEC 61730-1(Front sheet and back Sheet)	-	0	-
5.3.7 IS/IEC 61730-1(Insulation Barrier)	-	0	-
5.3.8 IS/IEC 61730-1(Electrical Connections)	-	0	-
5.3.9 IS/IEC 61730-1(Encapsulants)	-	0	-
5.3.10 IS/IEC 61730-1(Bypass Diodes)	-	0	-
5.4, 5.4.1 IS/IEC 61730-1(Mechanical and Electromechanical connections)	-	0	-
5.4.2 IS/IEC 61730-1(Screw Connctions)	-	0	-
5.4.3 IS/IEC 61730-1(Rivets)	-	0	-
5.4.4 IS/IEC 61730-1(Thread Cutting Screws)	-	0	-
5.4.5 IS/IEC 61730-1(Form/Press/Tight/Fit)	-	0	-
5.4.6 IS/IEC 61730-1(Connections by adhesives)	-	0	-
5.4.7 IS/IEC 61730-1(Other Connections)	-	0	-
5.5, 5.5.1 IS/IEC 61730-1(Materials)	-	0	-
5.5.2.3.2 IS/IEC 61730-1(Endurance to Electrical Stress)	-	0	-
5.5.2.3.3 IS/IEC 61730-1(Endurance to thermal stress-RTE (RTI) or TI)	-	0	-
5.5.2.3.4 IS/IEC 61730-1(Polymeric Insulating materials used as external Parts)	-	0	-
5.5.2.3.5 IS/IEC 61730-1(Polymeric Insulating Parts supporting live Parts)	-	0	-
5.5.3, 5.5.3.1 IS/IEC 61730-1(Metallic materials)	-	0	-
5.5.3.2 IS/IEC 61730-1(Current Carrying Parts)	-	0	-
5.5.4 IS/IEC 61730-1(Adhesives)	-	0	-
5.6, 5.6.1 IS/IEC 61730-1(Protection Agianst Electric Shock)	-	0	-
5.6.2 IS/IEC 61730-1(Protection Agianst accessibility to hazardeous live parts)	-	0	-
5.6.3 IS/IEC 61730-1(Insulation Coordination)	-	0	-
5.6.3.4(Clearances and creepage distances)	-	0	-
5.6.4 IS/IEC 61730-1(Distance through Insulation)	-	0	-
3.0(Application Classes)	-	0	-
4.0(Construction Requirements)	-	0	-
5.0(Polymeric Materials)	-	0	-
6.0(Internal Wiring and Current Carrying Parts)	-	0	-
7.0(Connections)	-	0	-
8.0(Bonding and Grounding)	-	0	-
9.0(Creepage and clearance distances)	-	0	-
10.0(Field Wiring Compartments with covers)	-	0	-
11.0(Marking)	-	0	-
12.0(Requirements of Supplied documents)	-	0	-
5.6.3 IS/IEC 61730-1(Insulation Coordination)	-	0	-
5.5.2.4 IS/IEC 61730-1(Polymeric Meterial used for Mechanical functions)	-	0	-
5.5.2 IS/IEC 61730-1(Polymeric Materials)	-	0	-
5.4.3 IS/IEC 61730-1(Rivets)	-	0	-
5.3.9 IS/IEC 61730-1(Encapsulants)	-	0	-
5.3.5 IS/IEC 61730-1(Junction Box for PV modules)	-	0	-
5.3.3 IS/IEC 61730-1(External Wirings and cables)	-	0	-
5.3, 5.3.1 IS/IEC 61730-1(Electrical Components and Insualtion)	-	0	-
5.2 IS/IEC 61730-1(Marking and Documentation)	-	0	-
5.6.4 IS/IEC 61730-1(Distance through Insulation)	-	0	-
5.5.2.4 IS/IEC 61730-1(Polymeric Meterial used for Mechanical functions)	-	0	-
5.5.2.3.4 IS/IEC 61730-1(Polymeric Insulating materials used as external Parts)	-	0	-
5.5.2.3.2 IS/IEC 61730-1(Endurance to Electrical Stress)	-	0	-
5.5.2 IS/IEC 61730-1(Polymeric Materials)	-	0	-
5.4.7 IS/IEC 61730-1(Other Connections)	-	0	-
5.3.4 IS/IEC 61730-1(Connectors)	-	0	-
5.3, 5.3.1 IS/IEC 61730-1(Electrical Components and Insualtion)	-	0	-
5.2 IS/IEC 61730-1(Marking and Documentation)	-	0	-
4(Classification, applications and intended use)	-	0	-
5.3(Electrical components and insulation)	-	0	-
5.4(Mechanical and electromechanical connections)	-	0	-
5.5(Materials)	-	0	-
5.5.2, 5.3.7(Polymeric materials)	-	0	-
5.6(Protection against electric shock)	-	0	-
5.5.2.3.3 IS/IEC 61730-1(Endurance to thermal stress-RTE (RTI) or TI)	-	0	-
5.5, 5.5.1 IS/IEC 61730-1(Materials)	-	0	-
5, 5.1 IS/IEC 61730-1(Requirements for design and Construction)	-	0	-
4 IS/IEC 61730-1(Classification, Application and Inteded Use)	-	0	-
5.6.2 IS/IEC 61730-1(Protection Agianst accessibility to hazardeous live parts)	-	0	-
5.6, 5.6.1 IS/IEC 61730-1(Protection Agianst Electric Shock)	-	0	-
5.5.4 IS/IEC 61730-1(Adhesives)	-	0	-
5.5.3.2 IS/IEC 61730-1(Current Carrying Parts)	-	0	-
5.5.3, 5.5.3.1 IS/IEC 61730-1(Metallic materials)	-	0	-
5.5.2.3.5 IS/IEC 61730-1(Polymeric Insulating Parts supporting live Parts)	-	0	-
5.4.6 IS/IEC 61730-1(Connections by adhesives)	-	0	-
5.4.5 IS/IEC 61730-1(Form/Press/Tight/Fit)	-	0	-
5.4.4 IS/IEC 61730-1(Thread Cutting Screws)	-	0	-
5.4.2 IS/IEC 61730-1(Screw Connctions)	-	0	-
5.4, 5.4.1 IS/IEC 61730-1(Mechanical and Electromechanical connections)	-	0	-
5.3.10 IS/IEC 61730-1(Bypass Diodes)	-	0	-
5.3.8 IS/IEC 61730-1(Electrical Connections)	-	0	-
5.3.7 IS/IEC 61730-1(Insulation Barrier)	-	0	-
5.3.6 IS/IEC 61730-1(Front sheet and back Sheet)	-	0	-
5.3.2 IS/IEC 61730-1(Internal Wiring)	-	0	-
5.3.2(Internal wiring)	-	0	-
5.3.4(Connectors)	-	0	-

02 Dec, 2029

-
-

10855

Intertek India Private Limited (Gujarat)

7166626

IS/IEC 61730 : PART 2 (2004)

Photovoltaic (PV) Module Safety Qualification Part 2 Requirements for Testing

1273748 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.1(Visual Inspection (MST 01))	-	50000	-
10.2(Accessibility test (MST 11))	-	11690	-
10.3(Cut susceptibility test (MST 12))	-	50100	-
10.4(Ground Continuity Test (MST 13))	-	250000	-
10.5(Impulse voltage test (MST 14))	-	9100	-
10.6(Dielectric withstand test (MST 16))	-	9485	-
10.7(Temperature test (MST 21))	-	18900	-
10.8(Fire test (MST 23))	-	200000	-
10.9(Reverse Current overload test (MST 26))	-	13300	-
10.10(Module breakage test (MST 32))	-	1600	-
11.1(Partial discharge-test (MST 15))	-	25000	-
11.2(Conduit Bending test (MST 33))	-	1600	-
11.3(Terminal box knockout tests (MST 44))	-	1600	-
Cl.5, Table 7(Thermal cycling (T200) (MST 51))	-	277000	-
Cl.5, Table 7(Thermal cycling (T50) (MST 51))	-	18200	-
Cl.5, Table 7(Humidity freeze (10HF) (MST 52))	-	118800	-
Cl.5, Table 7(Damp heat (DH1000) (MST 53))	-	268200	-
Cl.5, Table 7(UV resistance (MST 54))	-	18200	-
Cl.5, Table 7(Wet leakage current test (MST 17))	-	31850	-
Cl.5, Table 7(Robustness of termination test (MST 42))	-	27300	-
Cl.5, Table 7(Hot spot test (MST 22))	-	27300	-
Cl.5, Table 7(Mechanical load test (MST 34))	-	38200	-

02 Dec, 2029

-
-

10856

Intertek India Private Limited (Gujarat)

7166626

IS/IEC 61730 : PART 1 (2004)

Photovoltaic (PV) Module Safety Qualification Part 1 Requirements for Construction

250000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Application classes)	-	25000	-
4(Construction requirements)	-	25000	-
5(Polymeric materials)	-	25000	-
6(Internal wiring and current-carrying parts)	-	25000	-
7(Connections)	-	25000	-
8(Bonding and grounding)	-	25000	-
9(Creepage and clearance distances)	-	50000	-
10(Field wiring compartments with covers)	-	25000	-
11(Marking)	-	25000	-

02 Dec, 2029

-
-

10857

Intertek India Private Limited (Gujarat)

7166626

IS 14286 (2010)

Crystalline silicon terrestrial photovoltaic (PV) modules - Design qualification and type approval (First Revision)

Solar Photovoltaic Modules

1280550 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Marking)	-	50000	-
10.1(Visual inspection)	-	39033	-
10.2(Maximum power determination)	-	49662	-
10.3(Insulation test)	-	20840	-
10.4(Measurement of temperature coefficients)	-	65000	-
10.5(Measurement of NOCT)	-	38200	-
10.6(Performance at STC and NOCT)	-	49662	-
10.7(Performance at low irradiance)	-	7500	-
10.8(Outdoor exposure test)	-	52200	-
10.9(Hot-spot endurance test)	-	33318	-
10.10(UV preconditioning)	-	36400	-
10.11(Thermal cycling test)	-	372400	-
10.12(Humidity freeze test)	-	136400	-
10.13(Damp heat test)	-	318000	-
10.14(Robustness of termination test)	-	45500	-
10.15(Wet leakage current test)	-	163800	-
10.16(Mechanical load test)	-	38200	-
10.17(Hail test)	-	22750	-
10.18(Bypass diode thermal' test)	-	42300	-

02 Dec, 2029

-
-

10858

RTRC LIMITED, GURUGRAM

9177406

IS 14255 (1995)

Aertal bunched cables - For working voltages up to and including 1100 Volts - Specification

CABLE

18500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Phase/Street Lighting conductor)	-	0	-
4.2(Messenger (Neutral Conductor or Otherwise))	-	0	-
5.1(Insulation)	-	0	-
6.1(Flexibility class)	-	0	-
6.2(Compactness)	-	0	-
6.2(No of strands)	-	0	-
6.2(Surface)	-	0	-
6.3(Protective barrier)	-	0	-
6.4(size of street lighting conductor)	-	0	-
6.5(Size of messenger conductor )	-	0	-
6.6(Joints in messenger conductor )	-	0	-
6.6(Direction of outer layer)	-	0	-
7.1(Insulation)	-	0	-
7.2( Thickness of insulation)	-	500	-
7.3(Tolerance on thickness of insulation )	-	0	-
7.4(Aplication of the insulation )	-	0	-
7.5(Colour of the insulation )	-	0	-
8.1(Core identification)	-	0	-
8.2(Core identification)	-	0	-
8.3(Identification by other means)	-	0	-
9.1(Assembly (Laying up))	-	0	-
9.2(Assembly (Laying up))	-	0	-
9.3(Direction of lay)	-	0	-
10.1 a) i)(Tests on phase/street light conductor: tensile test - Test method IS10810:Part 2)	-	500	-
10.1 a) ii)(Wrapping test - 10810: Part 3)	-	500	-
10.1 a) iii)(Resistance test - IS10810: Part 5)	-	1000	-
10.1 b) i)(Test on messenger conductor: Breaking load - IS 10810: Part 2)	-	1000	-
10.1 b) ii)(Test on messenger conductor: Elongation test - Cl 11.3)	-	1000	-
10.1 b) iii)(Test on messenger conductor: Resistance test - IS 10810: Part 5)	-	500	-
10.1 c) i)(Physical tests for XLPE Insulation: Tensile strength - IS 10810: Part 7)	-	500	-
10.1 c) i)(Physical tests for XLPE Insulation: elongation at break - IS 10810: part 7)	-	500	-
10.1 c) ii)(Ageing in air oven : Tensile strength variation - IS 10810:Part 11)	-	3000	-
10.1 c) ii)(Ageing in air oven : Elongation variation- IS 10810: Part 11)	-	500	-
10.1 c) iii)(Hot set test: Elongation under load - IS 10810: Part 30)	-	1000	-
10.1 c) iii)(Hot set test: Permanent elongation (set) after cooling - IS 10810: Part 30)	-	500	-
10.1 c) iv)(Shrinkage test : Shrinkage - 10810:Part 12)	-	500	-
10.1 c) iv)(Shrinkage test : Crack Observed - 10810:Part 12)	-	500	-
10.1 c) v)(Water ahsorption (Gravimetric) - IS 10810: Part 33 )	-	3000	-
10.1 d) i)(Physical test for PE insulation: Tensile strength - IS 10810: Part 7 )	-	500	Additional, If applicable
10.1 d) i)(Physical test for PE insulation: elongation at break - IS 10810: Part 7)	-	500	Additional, If applicable
10.1 d) ii)(Melt flow index- IS 10810: Part 23)	-	1500	Additional charge, If applicable
10.1 d) iv)(Vicat softening point -IS 10810: Part 22)	-	2500	Additional charge, If applicable
10.1 d) v)(Environmental stress cracking -IS 10810:Part29)	-	4500	Additional charge, If applicable
10.1 f)(Insulation resistance (Volume resistivity) test a) volume resistivity at 27°C - IS 10810: Part 43)	-	1000	-
10.1 f)(Insulation resistance (Volume resistivity) test b) volume resistivity at 70°C - IS 10810: Part 43)	-	1000	-
10.1 g)(High voltage test - IS10810:Part 45)	-	1500	-
11.4(Bending Test on the Completed Cable ( Optional) )	-	1000	Additional charge, If applicable
11.4(Bending Test on the Completed Cable ( Optional))	-	1000	Additional charge, If applicable
10.1 d) iii)(Carbon Black Content)	-	3500	Additional charge, If applicable

03 Apr, 2027

-
Included w.e.f. 24.04.2024

10859

RTRC LIMITED, GURUGRAM

9177406

IS 1554 : Part 1 (1988)

Specification for pvc insulated (Heavy Duty) electric cables: Part 1 for working voltages up to and including 1100 v (Third Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(MATERIALS : CONDUCTOR)	-	0	Additional Charges, Rs 1500/- for each additional core. Additional Charges for FR-LSH/FR test as applicable
4.1.1(INSULATION : General Purjose Insulaiion)	-	0	-
4.1.2(INSULATION : Heat Resisting Insulation)	-	0	-
5.1(MATERIALS : FILLER AND INNER SHEATH)	-	0	-
5.2(MATERIALS : FILLER AND INNER SHEATH)	-	0	-
6.1(MATERIALS : ARMGURING)	-	0	-
6.2(MATERIALS : ARMGURING)	-	0	-
7.1.1(OUTER SHEATH : For Cables with General Purpose InsuIafion)	-	0	-
7.1.2(OUTER SHEATH : For Cables with Heat Resisting InsuIalion)	-	0	-
8.1(CONSTRUCTION : CONDUCTOR)	-	0	-
8.2(CONSTRUCTION : CONDUCTOR)	-	0	-
9.1(INSULATION )	-	0	-
9.2(INSULATION : Thickness of Insulation)	-	500	-
9.3(INSULATION :Tolerance on Thickness of Insulation)	-	0	-
9.4(INSULATION : Application of Insulation)	-	0	-
10.1(CORE IDENTIFICATION)	-	0	-
10.2(CORE IDENTIFICATION)	-	0	-
10.3(CORE IDENTIFICATION)	-	0	-
10.3.1(Arrangement of Marking)	-	0	-
11.1(LAYING UP OF CORES)	-	0	-
11.2(LAYING UP OF CORES)	-	0	-
12.1(INNER SHEATH)	-	0	-
12.2(INNER SHEATH)	-	0	-
12.3(INNER SHEATH :Thickness of Inner Sheath)	-	0	-
12.3.1(INNER SHEATH :Thickness of Inner Sheath)	-	0	-
13.1.1(ARMOURING : Application)	-	0	-
13.1.2(Armouring: Coverage )	-	0	-
13.1.3(ARMOURING : Direction of lay )	-	0	-
13.1.4(ARMOURING : Application)	-	0	-
13.2(ARMOURING : Type of Armour)	-	0	-
13.2.1(ARMOURING : Type of Armour)	-	0	-
13.3(Armouring : Dimensions -Wire Diameter)	-	0	-
13.3(Armouring : Dimensions -Formed wire )	-	500	-
13.4(ARMOURING : Joints)	-	0	-
13.5.1(ARMOURING : Resistance)	-	500	-
13.5.2(ARMOURING : Resistance)	-	0	-
13.6 a)(ARMOURING: Tensile Strength)	-	500	-
13.6 b)(ARMOURING: Elongation )	-	0	-
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	500	-
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	0	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	500	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	500	-
13.6 g)(ARMOURING: Resistivity)	-	500	-
14.1(OUTER SHEATH)	-	0	-
14.2(OUTER SHEATH)	-	0	-
14.3(OUTER SHEATH : Colour )	-	0	-
14.4.1(Thickness of Outer Sheath : Unarmowed Cables)	-	0	-
14.4.2(Thickness of Outer Sheath : Armoured Cables)	-	500	-
15.1 a) 1)(Tests on conductor : Annealing test ( for copper ))	-	0	-
15.1 a) 2)(Tensile test (for aluminium) - Before stranding )	-	0	-
15.1 a) 2)(Tensile test (for aluminium) - After stranding )	-	0	-
15.1 a) 3)(Tests on conductor : Wrapping test ( for aluminium ))	-	0	-
15.1 a) 4)(Tests on conductor : Conductor resistance test)	-	500	-
15.1 a) 4)(Resistance test - Neutral conductor )	-	0	-
15.1 d)1)(Phyaical tests for insulation : Tensile Test)	-	500	-
15.1 d)1)(Phyaical tests for insulation : Elongation )	-	0	-
15.1 d)1)(Physical tests for sheath : Tensile stregth )	-	500	-
15.1 d)1)(Physical tests for sheath : Elongation )	-	0	-
15.1 d)2)(Phyaical tests for insulation- Ageing in air Oven : Tensile Test)	-	500	-
15.1 d)2)(Phyaical tests for insulation - Ageing in air oven : Elongation )	-	0	-
15.1 d)2)(Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	0	-
15.1 d)2)(Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	0	-
15.1 d)2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	500	-
15.1 d)2)(Physical tests for outer sheath -Ageing in air oven : Elongation )	-	0	-
15.1 d)2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	0	-
15.1 d)2)(Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	0	-
15.1 d)3)(Phyaical tests for insulation : Shrinkage )	-	500	-
15.1 d)3)(Phyaical tests for insulation : Shrinkage - Crack observed )	-	0	-
15.1 d)3)(Phyaical tests for Sheath : Shrinkage )	-	0	-
15.1 d)3)(Phyaical tests for Sheath : Shrinkage - Crack observed )	-	0	-
15.1 d)4)(Hot deformation : Insulation )	-	500	-
15.1 d)4)(Hot deformation : Sheath )	-	0	-
15.1 d)5)( Loss of mass in air oven- Insulation )	-	500	-
15.1 d)5)( Loss of mass in air oven- sheath )	-	0	-
15.1 d)6)(Heat shock test- Insulation )	-	500	-
15.1 d)6)(Heat shock test- sheath )	-	0	-
15.1 d)7)(Thermal stability- insulation )	-	500	-
15.1 d)7)(Thermal stability- Sheath )	-	0	-
15.1 e)(Insulation resistance test : Volume Resistivity )	-	500	-
15.1 e)(Insulation resistance test : IR Constant )	-	0	-
15.1 f)(High voltage test ( water immersion test ))	-	1500	-
15.1 g)(High voltage test at room temperature)	-	500	-
15.1 g)(High voltage test at room temperature)	-	0	-
15.4 a)(Cold bend test- Insulation ( Optional test))	-	500	-
15.4 a)(Cold bend test- Sheath ( Optional test))	-	500	-
15.4 b)(Cold impact test- Insulation ( Optional test))	-	0	-
15.4 b)(Cold impact test- Sheath ( Optional test))	-	0	-
15.4 c)(Armour resistance test ( for other than mining cables ).- Optional test )	-	500	-
16.1(DETAILS OF TESTS : General)	-	0	-
16.2(DETAILS OF TESTS : High Voltage Test at Room Temperature)	-	0	-
16.3.1(High Voltage Test ( Water Immersion Test ) : a.c. Test)	-	500	-
16.3.2(High Voltage Test ( Water Immersion Test ) : d.c. Test)	-	500	-
16.4(Flammability Test)	-	0	-
16.5(Oxygen Index Test)	-	2500	additional charge, if applicable
16.6(Flame Retardance Test on Single Cables)	-	0	-
16.7(Flame Retardance Test on Bunched Cables)	-	5500	additional charge, if applicable
16.9(Test for Halogen Acid Gas Evolution)	-	3500	additional charge, if applicable
16.1(Temperature Index)	-	0	-
17.1(IDENTIFICATION : Manufacturer’s Identification)	-	0	-
17.2(IDENTIFICATION : Cable Identification)	-	0	-
17.2.1(IDENTIFICATION : Cable Identification)	-	0	-
17.3(IDENTIFICATION : Cable Code)	-	0	-
15.1.e(Insulation resistance Test- Insulation resistance At Maximum rated temperature temperature)	-	0	-
15.1.e(Insulation resistance Test- Insulation resistance constant At Room temperature)	-	0	-
15.1.e(Insulation resistance Test- Volume Resistivity At Maximum rated temperature temperature)	-	0	-
15.1.e(Insulation resistance Test- Volume Resistivity At Room temperature)	-	500	-
16.4(Flammability Test- Un affected portion)	-	0	-
16.4(Flammability Test- Period of Burning)	-	0	-
9.3(Minimum Thickness of Reduce core insulation)	-	0	-
9.2(Thickness of Reduce core insulation)	-	0	-
3.1 Table 2 IS 8130(Number of wires in the conductor)	-	0	-
Cl No. 16.10(Smoke density test)	-	3500	additional charge, if applicable
Cl No. 16.8(Test for specific optical density of smoke)	-	0	-
Table 4(Copper purity test)	-	0	-

03 Apr, 2027

-
Included w.e.f. 24.04.2024

10860

Atharva Laboratories Pvt. Ltd. (D115A), Noida (8134206)

8134206

IS 13893 (1994)

Polyurethane soles semirigid - specification

5300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Design)	-	200	Ok
4.2(Thickness )	-	300	Ok
4.3(Relative density )	-	300	Ok
4.3(Hardness Shore(A))	-	300	Ok
4.3(Tensile Strength )	-	600	Ok
4.3(Elongation at break)	-	200	Ok
4.3(Abrasion Resistance)	-	800	Ok
4.3(Flexural strength )	-	1000	Ok
4.3(Ross Flex test)	-	800	Ok
4.3.2(Ageing test)	-	0	N/A
5, 5.1, 5.2(Packing And Marking)	-	0	N/A
Cl.5, 5.1, 5.2(Packing And Marking)	-	0	N/A
4.2 (Amendment 2)(Thickness)	-	0	N/A
4.3.1 Table 1 i) (Amendment 2)(Relative Density)	-	0	N/A
4.3.1 Table 1 iii) (Amendment 2)(Abrasion Resistance at applied force of 10 N)	-	0	N/A
4.3.1 Table 1 iv) (Amendment 2)(Flexing Resistance, Bennewart method)	-	0	N/A
4.3.1 Table 1 v) (Amendment 2)(Hydrolysis Resistance, cut growth after 150000 flexes)	-	0	Ok
4.3.1 Table 1 vi) (Amendment 2)(Tensile Strength)	-	0	N/A
4.3.1 Table 1 vii) (Amendment 2)(Elongation at break)	-	0	N/A
4.3.1 Table 1 viii) (Amendment 2)(Tear Strength (average force))	-	800	Ok
4.3.1 Table 1 ii) (Amendment 2)(Hardness, degree, Shore A)	-	0	N/A

21 Jul, 2028

-
Amendment No. 2 included w.e.f. 05.04.2024

Bureau of Indian Standards

The National Standards Body of India

Search by IS Number

No Record Found