BIS - LIMS (Laboratory Information Management System)

Search by IS Number

Reset

11171 Results

S.No.

Lab Name

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

11131

BIS, Eastern Regional Laboratory (ERL)

IS 2347 (2017)

Domestic pressure cooker - Specification (Sixth Revision)

- View breakup
Rs. 14700/- excluding test on handles and chemical tests.

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Capacity )	-
5.2 (Safety Relief Device)	-
6.1.1 (Pressure Regulating Device)	-
8.1 (Air Pressure Test)	-
8.2 (Proof Pressure Test)	-
8.3 (Operating Test for Pressure Regulating Device)	-
8.4 (Test for Safety Pressure Relief Device)	-
8.5 (Bursting Pressure Test)	-
8.6.1 (Tests for Removal of Lid under Pressure For Outer Lid Cooker)	-

Partial

-
Facility not available for Cl 8.6(test for Outer lid type),8.7,8.8,8.9,8.10,7.4, For Chemical tests, see status of IS for individual components (IS 21/6911/5522).

11132

BIS, Western Regional Laboratory (WRL)

IS 398 : Part 2 (1996)

Aluminium conductors for overhead transmission purposes - Specification: Part 2 aluminium conuuctors, galvanized steel - Reinforced (Third Revision)

Up to 100 sq mm

- View breakup
(I) For galvanized steel core only (consisting of 7 steel strands)- Rs.2850.00, (II) For galvanized steel reinforced stranded conductors with nominal aluminium area upto and including 100mm2-(a) For single steel wire core (1 steel + 6 Aluminium)- Rs. 1950.00 (b) For 7 wire core (7 steel + 6 Aluminium) - Rs. 4000.00, (III) For galvanized steel reinforced stranded conductors with nominal aluminium area more than 100mm2 (excluding special tests as per Cl. 13.9, 13.10 & 13.11)-(a) For stranded conductors with 37 strands-Rs.7900/-, (b) For stranded conductors with 49 strands-Rs.10000/-, (c) For stranded conductors with 61 strands-Rs.11100/-,

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
10 (elec) (Stranding)	-
10 (elec) (Stranding)	-
10 (elec) (Stranding)	-
13.4.2 (elec) (Ductility by Elongation Test before stranding)	-
13.4.2 (elec) (Ductility by Elongation Test after stranding)	-
13.6 (elec) (Resistance test-Aluminium wire before Stranding)	-
13.6 (elec) (Resistance test-Aluminium wire after stranding)	-
13.9 (elec) (Surface condition test)	-
13.10 (elec) (Ultimate breaking load)	-
13.11 (elec) (Stress-strain test)	-
13.8 Table-4 (elec) (Lay Ratio- Steel Core (6 Wire Layer))	-
13.8 Table-4 (elec) (Lay Ratio- Steel Core (6 Wire Layer))	-
13.8 Table-4 (elec) (Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-
13.8 Table-4 (elec) (Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-
13.8 Table-4 (elec) (Lay Ratio- Aluminium Wire Outermost Layer)	-
13.7.2 (elec) (Uniformity of Zinc coating)	-
13.7.2 (elec) (Mass of Zinc coating)	-
13.5.2 (elec) (Wrapping Test Galvanized Steel Wires After Stranding)	-
13.5.2 (elec) (Wrapping Test Galvanized Steel Wires Before Stranding)	-
13.5.1 (elec) (Wrapping Test Aluminium Wires After Stranding)	-
13.5.1 (elec) (Wrapping Test Aluminium Wires Before Stranding)	-
13.4.1 (elec) (Ductility by Torsion Test after stranding)	-
13.4.1 (elec) (Ductility by Torsion Test before stranding)	-
13.3 Table 2 (elec) (Breaking Load of Steel Wires After Stranding)	-
13.3 Table 2 (elec) (Breaking Load of Steel Wires Before Stranding)	-
13.3 Table 1 (elec) (Breaking Load of Aluminium Wires After Stranding)	-
13.3 Table 1 (elec) (Breaking Load of Aluminium Wires Before Stranding)	-
8.1.1 & 13.2 Table 2 (elec) (Diameter of Steel Wires After Stranding)	-
8.1.1 & 13.2 Table-1 (elec) (Diameter of Aluminium Wires After Stranding)	-
8.1.1 & 13.2 Table 2 (elec) (Diameter of Steel Wires Before Stranding)	-
8.1.1 & 13.2 Table-1 (elec) (Diameter of Aluminium Wires Before Stranding)	-

Partial

-
Test facility not available for Cl. 13.9, 13.10 and 13.11 for size 100 sq.mm and above.

11133

BIS, Western Regional Laboratory (WRL)

IS 3854 (1997)

Switches for domestic and similar purposes - Specification (Second Revision)

- View breakup
6A Screw type terminals-Rs.4900/-, 6A Screwless type terminals-Rs.5850/-,10A Screw type terminals-Rs.5050/-, 10A Screwless type terminals-Rs.6400/-, 16A Screw type terminals-Rs.5850/-,16A Screwless type terminals-Rs.7900/-, 20A-Rs.5250/-, 25A-Rs.5900/-, 32A-Rs.6250/-, 40A-Rs.6550/-, 63A-Rs.6200/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
10 (Protection against Electric Shock)	-
11.1 (Provision for earthing)	-
12.2.3 (Mechanical strength of terminals)	-
12.2.4 (Resistance to corrosion)	-
12.2.5 (Undue damage to conductor)	-
12.2.7 (Insertion of conductor)	-
12.2.11 (Distance between screw and conductor)	-
12.3.2 (Screwless terminals)	-
12.3.4 (Material of terminals)	-
12.3.11 (vi) Electrical & Thermal Stresses [Cl 12.3.11])	-
12.3.12 (vii) Deflection Stresses [Cl. 12.3.12])	-
13.15 (q) Requirements for membrane in inlet opening [ Cl. 13.15])	-
15.1 (Resistance to Ageing, to Harmful Ingress of water and to Humidity [Cl. 15]: Resistance to Ageing, [Cl. 15.1])	-
15.2 (b)Resistance to Harmful ingress of water [Cl. 15.2])	-
15.3 (c) Resistance to Humidity [Cl. 15.3])	-
16.1 (Insulation resistance [Cl. 16.1])	-
16.2 ( Electric Strength [Cl. 16.2])	-
17 (Temperature- rise [Cl. 17])	-
19 (Normal Operation [Cl. 19] a) General & Operation)	-
19 (b) Electric Strength)	-
19 (c)Temperature-rise )	-
19.2 (Normal Operation (For AX type Switches) [Cl. 19.2])	-
20 (Mechanical Strength Test [Cl. 20])	-
21 (Resistance to Heat [Cl.21])	-
22 (Screw, Current Carrying Part And Connection [Cl.22])	-
23.2 (Creepage distances, clearances and distance through sealing compound [Cl.23])	-
24.1.1 (Resistance to Abnormal Heat & Fire [Cl.24.1] [Glow Wire Test] [Cl.24.1.1])	-
8 (Marking)	-
8 (Marking)	-
8 (Marking)	-
8 (Marking)	-
8 (Marking)	-
8 (Marking)	-
8 (Marking)	-
8.9 (Marking)	-
8 (Marking)	-
7 (Classification)	-
7 (Classification)	-
7 (Classification)	-
7 (Classification)	-
7 (Classification)	-
7 (Classification)	-
7 (Classification)	-
12 (Terminals)	-
12.2.1 (Terminals)	-
12 (Terminals)	-
12.2.2 (Connection of conductor)	-
12.2.7 (Insertion of conductor)	-
12.2.9 (Locking against accidental loosening)	-
12.3.2 (Screwless terminals)	-
12.3.3 (Connectin of conductor)	-
12.3.4 (Material of terminals)	-
12.3.5 (Clamping)	-
12.3.7 (v) Interconnection of conductors [Cl. 12.3.7])	-
13.1 (a) Insulating lining, barriers and the like [Cl 13.1])	-
13.2 (b) Construction of switch [Cl 13.2])	-
13.2 (i) Installation Test)	-
13.3 (c) Covers,cover plates and actuating members [Cl 13.3])	-
13.4 (d) Ordinary switches [Cl 13.4])	-
13.5 (e) Rotary switches [Cl 13.5])	-
13.6 (f) Screws and other means [Cl 13.6])	-
12.3.7 (v) Interconnection of conductors [Cl. 12.3.7])	-
13.8 (h) Assessories combined with switches [Cl. 13.8])	-
13.9 (j) Switches other than ordinary switches [Cl. 13.9])	-
13.9 (j) Switches other than ordinary switches [Cl. 13.9])	-
13.1 (k) Switches to be installed in a box [Cl. 13.10])	-
13.12, 13.13, 13.14 (m) Inlet opening [Cl. 13.12.13.13 & 13.14])	-
13.15 (q) Requirements for membrane in inlet opening [ Cl. 13.15])	-
13.15 (q) Requirements for membrane in inlet opening [ Cl. 13.15])	-
14 (Mechanism [Cl. 14])	-
14.4 (Mechanism)	-
8 (Marking)	-
8 (Marking)	-
14.4 (Mechanism)	-
14.3 (d)Test for arcing and sparking [Cl 14.3])	-
21 (Resistance to Heat [Cl.21])	-
21 (Resistance to Heat [Cl.21])	-
23 (Creepage distances, clearances and distance through sealing compound [Cl.23])	-
24.2 (Resistance to tracking [For Switch other than ordinary] [Cl.24.2])	-
19.2 (Normal Operation (For AX type Switches) [Cl. 19.2])	-
22.1 (i) Screw & Nuts [Cl.22.1])	-
22.3 (iii) Electrical Connections [Cl.22.3])	-
22.4 (ii) Screw & rivets [Cl . 22.4])	-
22.5 (iv) Current carrying part [Cl.22.5])	-
18 (Marking and breaking Capacity[Cl. 18])	-
7 (Classification)	-
7 (Classification)	-
6.1 (Ratings)	-
6.2 (Ratings)	-
25 (Resistance to Rusting)	-

Partial

-
Complete TF is available for variety upto and including 20A. For above 20A rating (32A, 63A), the following facilities are not available: 1. Cl 17 Temperature rise 2. Cl 18, Making and breaking Capacity 3. Cl 19 Normal Operation"

11134

BIS, Eastern Regional Laboratory (ERL)

IS 398 : Part 2 (1996)

Aluminium conductors for overhead transmission purposes - Specification: Part 2 aluminium conuuctors, galvanized steel - Reinforced (Third Revision)

Complete up to 100 sqmm

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8.1.1 & 13.2 Table 2 (elec) (Diameter of Steel Wires After Stranding)	-
10 (elec) (Stranding)	-
13.3 Table 2 (elec) (Breaking Load of Steel Wires Before Stranding)	-
13.3 Table 2 (elec) (Breaking Load of Steel Wires After Stranding)	-
13.3 Table 1 (elec) (Breaking Load of Aluminium Wires After Stranding)	-
13.4.1 (elec) (Ductility by Torsion Test before stranding)	-
13.4.1 (elec) (Ductility by Torsion Test after stranding)	-
13.8 Table-4 (elec) (Lay Ratio- Steel Core (6 Wire Layer))	-
13.8 Table-4 (elec) (Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-
13.8 Table-4 (elec) (Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-
13.8 Table-4 (elec) (Lay Ratio- Aluminium Wire Outermost Layer)	-
13.5.2 (elec) (Wrapping Test Galvanized Steel Wires After Stranding)	-
13.5.1 (elec) (Wrapping Test Aluminium Wires After Stranding)	-
13.4.2 (elec) (Ductility by Elongation Test after stranding)	-
13.7.2 (elec) (Uniformity of Zinc coating)	-
13.7.2 (elec) (Mass of Zinc coating)	-
13.9 (elec) (Surface condition test)	-
13.10 (elec) (Ultimate breaking load)	-
13.6 (elec) (Resistance test-Aluminium wire after stranding)	-
10 (elec) (Stranding)	-
10 (elec) (Stranding)	-
13.6 (elec) (Resistance test-Aluminium wire before Stranding)	-
8.1.1 & 13.2 Table-1 (elec) (Diameter of Aluminium Wires After Stranding)	-
8.1.1 & 13.2 Table 2 (elec) (Diameter of Steel Wires After Stranding)	-
8.1.1 & 13.2 Table-1 (mech) (Diameter of Aluminium Wires Before Stranding)	-
10 (elec) (Stranding)	-
13.3 Table 1 (mech) (Breaking Load of Aluminium Wires After Stranding)	-
13.6 (elec) (Resistance test-Aluminium wire after stranding)	-
13.3 Table 1 (mech) (Breaking Load of Aluminium Wires Before Stranding)	-
8.1.1 & 13.2 Table-1 (mech) (Diameter of Aluminium Wires Before Stranding)	-
8.2.2 (Calculated resistance)	-

Partial

-
All tests are available up to and including 100 sq.mm. For Above 100 sq.mm. facility not available for Stress-Strain Test, Surface Condition, Ultimate B/L on stranded conductor.

11135

BIS, Eastern Regional Laboratory (ERL)

IS 1786 (2008)

High strength deformed steel bars and wires for concretere inforcement - Specification (Fourth Revision)

For all grades except for the tests mentioned in remarks

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 5 (Cl.5 Mean area of ribs/unit length (Ar), )	-
Cl. 5 (Cl. 5 - Mean projected area of transverse ribs (1/3 of Ar))	-
Cl 7.2 (Weight)	-
Cl. 8.1 Table 3 (Yield Stress (YS))	-
Cl. 8.1 Table 3 (Tensile Strength (TS))	-
Cl. 8.1 Table 3 (TS/YS ratio)	-
Cl. 8.1 Table 3 (Elongation, percentage)	-
4.1 (Sulphur and phosphorous)	-
Clause - 4.2 & 4.2.1 (Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 CARBON )	-
Clause - 4.2 & 4.2.1 (Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 SULPHUR)	-
Clause - 4.2 & 4.2.1 (Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 PHOSPHURS)	-
Clause - 4.2 & 4.2.1 (Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 NITROGEN)	-
Clause - 4.2 & 4.2.1 (Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 MANGANESE)	-
Clause - 4.2 & 4.2.1 (Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 SULPHUR+PHOSPHUR)	-
Clause - 4.2 & 4.2.1 (Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 CARBON +EQUIVELENT )	-
Cl. 8.1 Table 3 (Elongation, percentage)	-
Cl. 9.3, Table 4 (Bend Test )	-
Cl.9.4 & Cl. 9.4.1 (Rebend test)	-
8.18.1 Table 3 (Total elongation at maximum force)	-

Partial

-
Mech - Facility not available for pull out test, total elongation at maximum force. Chem- Facility not available for Micro-alloying elements. Declarations regarding type of 'Killed' material, Micro-alloys/low-alloys, Nitrogen content or any other parameter as per Note under clause 4.2 to be provided.

11136

BIS, Eastern Regional Laboratory (ERL)

IS 1554 : Part 1 (1988)

Specification for pvc insulated (Heavy Duty) electric cables: Part 1 for working voltages up to and including 1100 v (Third Revision)

Complete for Cat 01(up to 400sq.mm)Except optional test

- View breakup
Rs.16650/- for single core unarmoured cable, Rs.22500/- for two core, unarmoured cable, Rs.26700/- for two core armoured cable (Excluding addl. Type test for cables with improved fire performance.) For multi core cables, extra charges @ 35 % for each additional core shall be levied. Material testing charges as per relevant referred ISs Testing charges for Additional Type Tests for Improved Fire Performance Tests: Rs. 7100/- for category C1 Rs. 11700/- for category C2

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (MATERIALS : CONDUCTOR)	-
5.2 (MATERIALS : FILLER AND INNER SHEATH)	-
5.1 (MATERIALS : FILLER AND INNER SHEATH)	-
6.1 (MATERIALS : ARMGURING)	-
8.1 (CONSTRUCTION : CONDUCTOR)	-
8.2 (CONSTRUCTION : CONDUCTOR)	-
9.2 (INSULATION : Thickness of Insulation)	-
9.3 (INSULATION :Tolerance on Thickness of Insulation)	-
9.4 (INSULATION : Application of Insulation)	-
10.1 (CORE IDENTIFICATION)	-
10.3 (CORE IDENTIFICATION)	-
10.2 (CORE IDENTIFICATION)	-
11.1 (LAYING UP OF CORES)	-
12.1 (INNER SHEATH)	-
12.2 (INNER SHEATH)	-
12.3 (INNER SHEATH :Thickness of Inner Sheath)	-
12.3.1 (INNER SHEATH :Thickness of Inner Sheath)	-
13.1.1 (ARMOURING : Application)	-
13.1.2 (Armouring: Coverage )	-
13.1.3 (ARMOURING : Direction of lay )	-
13.1.4 (ARMOURING : Application)	-
13.2 (ARMOURING : Type of Armour)	-
13.2.1 (ARMOURING : Type of Armour)	-
13.3 (Armouring : Dimensions -Wire Diameter)	-
13.3 (Armouring : Dimensions -Formed wire )	-
13.4 (ARMOURING : Joints)	-
13.5.1 (ARMOURING : Resistance)	-
13.5.2 (ARMOURING : Resistance)	-
13.6 a) (ARMOURING: Tensile Strength)	-
13.6 b) (ARMOURING: Elongation )	-
13.6 c) (ARMOURING: Torsion Test (For round wire ) )	-
13.6 d) (ARMOURING: Winding Test(For formed wire))	-
13.6 e) (ARMOURING: Uniformity of zinc coating)	-
13.6 f) (ARMOURING: Mass of zinc coating )	-
13.6 g) (ARMOURING: Resistivity)	-
14.1 (OUTER SHEATH)	-
14.2 (OUTER SHEATH)	-
14.3 (OUTER SHEATH : Colour )	-
14.4.2 (Thickness of Outer Sheath : Armoured Cables)	-
15.1 a) 1) (Tests on conductor : Annealing test ( for copper ))	-
15.1 a) 2) (Tensile test (for aluminium) - Before stranding )	-
15.1 a) 2) (Tensile test (for aluminium) - After stranding )	-
15.1 a) 3) (Tests on conductor : Wrapping test ( for aluminium ))	-
15.1 a) 4) (Tests on conductor : Conductor resistance test)	-
15.1 a) 4) (Resistance test - Neutral conductor )	-
15.1 d)1) (Phyaical tests for insulation : Tensile Test)	-
15.1 d)1) (Phyaical tests for insulation : Elongation )	-
15.1 d)1) (Physical tests for sheath : Elongation )	-
15.1 d)1) (Physical tests for sheath : Tensile stregth )	-
15.1 d)1) (Physical tests for sheath : Elongation )	-
15.1 d)1) (Physical tests for sheath : Tensile stregth )	-
15.1 d)1) (Physical tests for sheath : Elongation )	-
15.1 d)2) (Phyaical tests for insulation- Ageing in air Oven : Tensile Test)	-
15.1 d)2) (Phyaical tests for insulation - Ageing in air oven : Elongation )	-
15.1 d)2) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-
15.1 d)2) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-
15.1 d)2) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-
15.1 d)2) (Physical tests for outer sheath -Ageing in air oven : Elongation )	-
15.1 d)2) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-
15.1 d)2) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-
15.1 d)3) (Phyaical tests for insulation : Shrinkage )	-
15.1 d)3) (Phyaical tests for insulation : Shrinkage - Crack observed )	-
15.1 d)3) (Phyaical tests for Sheath : Shrinkage )	-
15.1 d)3) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-
15.1 d)4) (Hot deformation : Insulation )	-
15.1 d)4) (Hot deformation : Sheath )	-
15.1 d)5) ( Loss of mass in air oven- Insulation )	-
15.1 d)5) ( Loss of mass in air oven- sheath )	-
15.1 d)6) (Heat shock test- Insulation )	-
15.1 d)6) (Heat shock test- sheath )	-
15.1 d)7) (Thermal stability- insulation )	-
15.1 d)7) (Thermal stability- Sheath )	-
15.1.e (Insulation resistance Test- Volume Resistivity At Room temperature)	-
15.1.e (Insulation resistance Test- Volume Resistivity At Maximum rated temperature temperature)	-
15.1.e (Insulation resistance Test- Insulation resistance constant At Room temperature)	-
15.1.e (Insulation resistance Test- Insulation resistance At Maximum rated temperature temperature)	-
16.2 (DETAILS OF TESTS : High Voltage Test at Room Temperature)	-
16.3.2 (High Voltage Test ( Water Immersion Test ) : d.c. Test)	-
16.3.1 (High Voltage Test ( Water Immersion Test ) : a.c. Test)	-
17.1 (IDENTIFICATION : Manufacturer’s Identification)	-
17.2 (IDENTIFICATION : Cable Identification)	-
17.2.1 (IDENTIFICATION : Cable Identification)	-
17.3 (IDENTIFICATION : Cable Code)	-
15.1 e) (Insulation resistance test : Volume Resistivity )	-
15.1 e) (Insulation resistance test : IR Constant )	-
15.1 d)3) (Phyaical tests for insulation : Shrinkage )	-
15.1 d)3) (Phyaical tests for Sheath : Shrinkage )	-
15.1 d)4) (Hot deformation : Insulation )	-
15.1 d)4) (Hot deformation : Sheath )	-
13.3 (Armouring : Dimensions -Formed wire )	-
14.4.1 (Thickness of Outer Sheath : Unarmowed Cables)	-
16.4 (Flammability Test)	-
8.1 (CONSTRUCTION : CONDUCTOR)	-
3.1 (MATERIALS : CONDUCTOR)	-
8.2 (CONSTRUCTION : CONDUCTOR)	-
9.3 (Minimum Thickness of Reduce core insulation)	-
9.2 (Thickness of Reduce core insulation)	-
3.1 Table 2 IS 8130 (Number of wires in the conductor)	-

Partial

-
For Category-01 and upto 400 sq mm: all tests are available except additional tests. For cat. C1 and C2 : Except oxygen Index,Temperature index, Flame Retardance, Smoke Density, Halogen acid Gas Evolution

11137

BIS, Guwahati Branch Laboratory (GBL)

IS 269 (2015)

Ordinary portland cement - Specification (Sixth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7 Table-3 iii b (Setting Time Final)	-
7 Table-3 iii a (Setting Time Initial)	-
7 Table-3 ii b (Expansion after aeration)	-
7 Table-3 ii b (Expansion by Autoclave)	-
7 Table-3 ii a (Expansion after aeration)	-
7 Table-3 ii a (Expansion by Le Chatelier)	-
7 Table-3 i. (Fineness)	-
7 Table-3 iv a (Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-
7 Table-3 iv b (Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-
7 Table-3 iv c (Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-
6 - Table - 1 i (Ratio of percentage of lime to percentages of silica, alumina and iron oxide - Cl 4 of IS 4032:1985)	-
6 - Table - 1 ii (Ratio of percentage of alumina to that of iron oxide - Cl 4 of IS 4032:1985)	-
6 - Table - 1 iii (Insoluble residue - Cl 4.10 of IS 4032:1985)	-
6 - Table - 1 iv (Magnesia - Cl 4.8 of IS 4032:1985)	-
6 - Table - 1 v (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-
6 - Table - 1 vi (Loss on ignition - Cl 4.2 of IS 4032:1985)	-
6 - Table - 1 vii (Chloride content - Cl 4.13 of IS 4032:1985)	-
6.1 Table-2 vii (Chloride content)	-
6.1 Table-2 vi (Loss on ignition)	-
6.1 Table-2 v (Total Sulphur Content calculated as Sulphuric Anhydride)	-
6.1 Table-2 iv (Magnesia)	-
6.1 Table-2 iii. (Insoluble residue)	-
6.1 Table-2 ii. (Ratio of percentage of alumina to that of iron oxide)	-
6.1 Table-2 i. (Ratio of percentage of lime to percentage of silica, alumina and iron oxide)	-
6.1 Table-2 viii (Alkali content)	-

Partial

-
Partial T.F. available. (Transverse Strength T.F. not available)

11138

BIS, Western Regional Laboratory (WRL)

IS 694 (2010)

Polyvinyl chloride insulated unsheathed and sheathed cables/cords with rigid and flexible conductor for rated voltages up to and including 450/750 v (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
table 1 e) 3) (IR constant- Room temp )	-
table 1 e) 3) (IR constant- max. Temp)	-
10.2 (HV (room temperature))	-
10.1 (HV (water immersion))	-
Table 1 iii) d) 9) (Cold impact for sheath)	-
Table 1 iii) d) 8) (Cold bend for sheath)	-
Table 1 iii) c) 9) (Cold impact for insulation)	-
Table 1 iii) c) 8) (Cold bend for insulation)	-
Table 1 iii) d) 7) (Thermal stability- Sheath )	-
Table 1 iii) c) 7) (Thermal stability- Insulation )	-
Table 1 iii) d) 6) (Hot deformation -Indentation depth - Sheath )	-
Table 1 iii) d) 5) (Heat shock-Sheath )	-
Table 1 iii) c) 5) (Heat shock-Insulation )	-
Table 1 iii) d) 4) (Shrinkage- Sheath )	-
Table 1 iii) c) 4) (Shrinkage-Insulation)	-
Table 1 iii) d) 2) (Loss of mass- Sheath )	-
Table 1 iii) c) 2) (Loss of mass- Insulation )	-
Table 1 iii) d) 3) (Sheath- Elongation variation)	-
Table 1 iii) d) 3) (Sheath- TS variation)	-
Table 1 iii) d) 3) (Sheath- Elongation (After ageing))	-
Table 1 iii) d) 3) (Sheath- Tensile strength (After ageing))	-
Table 1 iii) d) 1) (Sheath- Elongation (Without ageing))	-
Table 1 iii) c) 3) (Elongation variation)	-
Table 1 iii) c) 3) (TS variation)	-
Table 1 iii) c) 3) (Elongation (After ageing))	-
Table 1 iii) c) 3) (Tensile strength (After ageing))	-
Table 1 iii) c) 1) (Elongation (Without ageing))	-
Table 1 iii) c) 1) (Tensile strength (Without ageing))	-
4.2 (Conductor resistance test)	-
4.1 (Wrapping test (for Al))	-
4.1 (Tensile test (for Al)- After Stranding)	-
4.1 (Tensile test (for Al)-Before Stranding)	-
4.1 (Annealing test (for copper))	-
(Cl.16.1) (Cl.19.1) (Conductor- Diameter )	-
10.9 (Additional ageing test (OU cables only) -HV test (at 60±3oC))	-
11.2 (Legibility)	-
11.1 (Durability)	-
11 (Identification)	-
10.9 (Additional ageing test (OU cables only) -HV test (at 60±3oC))	-
10.4 (Flammability test- Unaffected portion)	-
10.4 (Flammability test-Burning after flame removal)	-
Table 1 iii) d) 4) (Cracks Observed)	-
Table 1 iii) c) 4) (Cracks Observed)	-
(Cl. 18.1.4) (Cl. 19.1.5) (Cl. 20.1.4) (Cl. 22.1.4) (Colour of Sheath)	-
5.2 (Application )	-
9.1 (Ovality)	-
(Cl.6.1.3 of IS 8130:2013) (Flexible Conductors (Classes 5))	-
(Cl.6.1.3 of IS 8130:2013) ( Flexible Conductors (Classes 5))	-
(Cl.6.1.3 of IS 8130:2013) (Stranded circular non compacted conductors(Class-2))	-
(Cl.6.1.3 of IS 8130:2013) (Stranded compacted circular conductors and shaped conductors (Class 2))	-
(Cl.6.1.3 of IS 8130:2013) (Stranded circular non compacted conductors (Class-2))	-
(Cl.6.1.3 of IS 8130:2013) (Solid Conductor (Class 1))	-
(Cl.6.1 of IS 8130:2013) (Solid Conductor (Class 1))	-
(Cl.6.1 of IS 8130:2013) (Solid Conductor (Class 1))	-
(Cl.16.1) (Cl.19.1) (Conductor)	-
(Cl.16.1) (Cl.19.1) (Conductor)	-
(Cl.16.1) (Cl.19.1) (Conductor)	-
(Cl. 18.1.3) (Cl. 19.1.4) (Cl. 20.1.3) (Cl. 21.1.3) (Cl. 22.1.3) (Assembly of cores )	-
12 (CONSTRUCTION Core Identification)	-
8.1 (Sheath Material )	-
7 (Binder Tape)	-
6.1 (Filler)	-
6.2 (Filler)	-
5.1 (Insulation)	-
4.4 (Joints in Conductor)	-
4.4 (Joints in Conductor)	-
4.1 (Conductor - Material)	-
4.1 (Conductor - Material)	-
11 (Identification)	-
8.3 (Thickness of Sheath)	-
4.1 (Annealing test (for copper))	-
9 (Overall dimensions)	-
Table 1 iii) c) 6) (Hot deformation - Indentation depth- Insulation)	-
Table 1 iii) d) 1) (Sheath -Tensile strength (Without ageing))	-
8.3 (Minimum thickness of Sheath)	-
8.3 (Avarage thickness of Sheath)	-
5.3 (Minimum thickness of insulation)	-
5.3 (Avarage thickness of insulation)	-
Table 1 iii) c) 1) (Elongation (Without ageing))	-

Partial

-
Test facility not available for Copper purity test and FR/FRLSH category cables

11139

BIS, Southern Regional Laboratory (SRL)

IS 694 (2010)

Polyvinyl chloride insulated unsheathed and sheathed cables/cords with rigid and flexible conductor for rated voltages up to and including 450/750 v (Fourth Revision)

PVC Cables except FR & FRLSH Category

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
13 (Cable code)	-
11.2 (Legibility)	-
11.1 (Durability)	-
11 (Identification)	-
10.9 (Additional ageing test (OU cables only) -HV test (at 60±3oC))	-
10.4 (Flammability test- Unaffected portion)	-
10.4 (Flammability test-Burning after flame removal)	-
table 1 e) 3) (IR constant- max. Temp)	-
table 1 e) 3) (IR constant- Room temp )	-
table 1 e) 3) (Volume Resistivity - Maximum temp)	-
table 1 e) 3) (Volume Resistivity - Room temp )	-
10.2 (HV (room temperature))	-
10.1 (HV (water immersion))	-
10.1 (HV (water immersion))	-
Table 1 iii) d) 9) (Cold impact for sheath)	-
Table 1 iii) d) 8) (Cold bend for sheath)	-
Table 1 iii) c) 9) (Cold impact for insulation)	-
Table 1 iii) c) 8) (Cold bend for insulation)	-
Table 1 (Category Code)	-
Table 1 iii) d) 7) (Thermal stability- Sheath )	-
Table 1 iii) c) 7) (Thermal stability- Insulation )	-
Table 1 iii) d) 6) (Hot deformation -Indentation depth - Sheath )	-
Table 1 iii) c) 6) (Hot deformation - Indentation depth- Insulation)	-
Table 1 iii) d) 5) (Heat shock-Sheath )	-
Table 1 iii) c) 5) (Heat shock-Insulation )	-
Table 1 iii) d) 4) (Cracks Observed)	-
Table 1 iii) d) 4) (Shrinkage- Sheath )	-
Table 1 iii) c) 4) (Cracks Observed)	-
Table 1 iii) c) 4) (Shrinkage-Insulation)	-
Table 1 iii) d) 2) (Loss of mass- Sheath )	-
Table 1 iii) c) 2) (Loss of mass- Insulation )	-
Table 1 iii) d) 3) (Sheath- Elongation variation)	-
Table 1 iii) d) 3) (Sheath- TS variation)	-
Table 1 iii) d) 3) (Sheath- Elongation (After ageing))	-
Table 1 iii) d) 3) (Sheath- Tensile strength (After ageing))	-
Table 1 iii) d) 1) (Sheath- Elongation (Without ageing))	-
Table 1 iii) d) 1) (Sheath -Tensile strength (Without ageing))	-
Table 1 iii) c) 3) (Elongation variation)	-
Table 1 iii) c) 3) (TS variation)	-
Table 1 iii) c) 3) (Elongation (After ageing))	-
Table 1 iii) c) 3) (Tensile strength (After ageing))	-
Table 1 iii) c) 1) (Elongation (Without ageing))	-
Table 1 iii) c) 1) (Tensile strength (Without ageing))	-
(Cl. 18.1.4) (Cl. 19.1.5) (Cl. 20.1.4) (Cl. 22.1.4) (Colour of Sheath)	-
8.3 (Thickness of Sheath)	-
5.2 (Application )	-
5.3 (Thickness of Insulation)	-
9.1 (Ovality)	-
9 (Overall dimensions)	-
4.2 (Conductor resistance test)	-
4.1 (Wrapping test (for Al))	-
4.1 (Tensile test (for Al)- After Stranding)	-
4.1 (Tensile test (for Al)-Before Stranding)	-
4.1 (Annealing test (for copper))	-
(Cl.16.1) (Cl.19.1) (Conductor- Diameter )	-
(Cl.16.1) (Cl.19.1) (Conductor)	-
(Cl. 18.1.3) (Cl. 19.1.4) (Cl. 20.1.3) (Cl. 21.1.3) (Cl. 22.1.3) (Assembly of cores )	-
8.1 (Sheath Material )	-
7 (Binder Tape)	-
6.2 (Filler)	-
6.1 (Filler)	-
5.1 (Insulation)	-
4.4 (Joints in Conductor)	-
4.4 (Joints in Conductor)	-
4.1 (Conductor - Material)	-
4.1 (Conductor - Material)	-

Partial

-
" 30 m Excluding Except FR & FRLSH test, Cu Purity test

11140

BIS, Guwahati Branch Laboratory (GBL)

IS 455 (2015)

Portland slag cement - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 7 Table-2 (Cl. 7 Table-2 iii b (Setting time Final))	-
Cl. 7 Table-2 (Cl. 7 Table-2 iii a (Setting time Initial))	-
Cl. 7 Table-2 (Cl. 7 Table-2 ii b (Soundness , Autoclave Expansion ))	-
Cl. 7 Table-2 (Cl. 7 Table-2 ii b (Expansion after aeration ))	-
Cl. 7 Table-2 (Cl. 7 Table-2 ii a (Soundness , Le Chatelier Expansion ))	-
Cl. 7 Table-2 (Cl. 7 Table-2 ii a (Expansion after aeration ))	-
Cl. 7 Table-2 (Cl. 7 Table-2 i (Fineness ))	-
Cl. 7 Table-2 (Cl. 7 Table-2 iv a (Compressive Strength 72±1 hr IS))	-
Cl. 7 Table-2 (Cl. 7 Table-2 iv b (Compressive Strength 168±2 hr ))	-
Cl. 7 Table-2 (Cl. 7 Table-2 iv c (Compressive Strength 672±4 hr) )	-
6 - Table - 1 ii (Magnesia - Cl 6.8 of IS 4032:1985)	-
6 - Table - 1 iii (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 6.11 of IS 4032:1985)	-
6 - Table - 1 iv (Sulphide sulphur (S) - Cl 6.12 of IS 4032:1985)	-
6 - Table - 1 v (Loss on ignition - Cl 6.2 of IS 4032:1985)	-
6 - Table - 1 i (Insoluble residue - Cl 6.9 of IS 4032:1985)	-
6 - Table - 1 vi (Chloride content - Cl 4.13 of IS 4032:1985)	-
6 - Table - 1 vii ( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-

Partial

-
Partial T.F. available. (Transverse Strength Test not available)

11141

BIS, Western Regional Laboratory (WRL)

IS 1554 : Part 1 (1988)

Specification for pvc insulated (Heavy Duty) electric cables: Part 1 for working voltages up to and including 1100 v (Third Revision)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
9.2 (INSULATION : Thickness of Insulation)	-
12.3 (INNER SHEATH :Thickness of Inner Sheath)	-
13.3 (Armouring : Dimensions -Wire Diameter)	-
13.3 (Armouring : Dimensions -Formed wire )	-
13.6 f) (ARMOURING: Mass of zinc coating )	-
13.6 a) (ARMOURING: Tensile Strength)	-
13.6 c) (ARMOURING: Torsion Test (For round wire ) )	-
13.6 d) (ARMOURING: Winding Test(For formed wire))	-
13.6 f) (ARMOURING: Mass of zinc coating )	-
13.6 g) (ARMOURING: Resistivity)	-
14.4.1 (Thickness of Outer Sheath : Unarmowed Cables)	-
15.1 a) 1) (Tests on conductor : Annealing test ( for copper ))	-
15.1 a) 4) (Tests on conductor : Conductor resistance test)	-
15.1 a) 4) (Resistance test - Neutral conductor )	-
15.1 d)1) (Phyaical tests for insulation : Tensile Test)	-
15.1 d)1) (Phyaical tests for insulation : Elongation )	-
15.1 d)2) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-
15.1 d)2) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-
15.1 d)2) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-
15.1 d)2) (Physical tests for outer sheath -Ageing in air oven : Elongation )	-
15.1 d)2) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-
15.1 d)2) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-
15.1 d)3) (Phyaical tests for insulation : Shrinkage )	-
15.1 d)3) (Phyaical tests for Sheath : Shrinkage )	-
15.1 d)4) (Hot deformation : Insulation )	-
15.1 d)4) (Hot deformation : Sheath )	-
15.1 d)5) ( Loss of mass in air oven- Insulation )	-
15.1 d)5) ( Loss of mass in air oven- sheath )	-
15.1 d)6) (Heat shock test- Insulation )	-
15.1 d)6) (Heat shock test- sheath )	-
15.1 d)7) (Thermal stability- insulation )	-
15.1 d)7) (Thermal stability- Sheath )	-
15.1.e (Insulation resistance Test- Insulation resistance constant At Room temperature)	-
15.1.e (Insulation resistance Test- Insulation resistance At Maximum rated temperature temperature)	-
15.4 a) (Cold bend test- Insulation ( Optional test))	-
15.4 a) (Cold bend test- Sheath ( Optional test))	-
15.4 b) (Cold impact test- Insulation ( Optional test))	-
15.4 b) (Cold impact test- Sheath ( Optional test))	-
15.4 c) (Armour resistance test ( for other than mining cables ).- Optional test )	-
16.2 (DETAILS OF TESTS : High Voltage Test at Room Temperature)	-
16.3.1 (High Voltage Test ( Water Immersion Test ) : a.c. Test)	-
16.3.2 (High Voltage Test ( Water Immersion Test ) : d.c. Test)	-
16.4 (Flammability Test)	-
3.1 (MATERIALS : CONDUCTOR)	-
4.1.1 (INSULATION : General Purjose Insulaiion)	-
4.1.2 (INSULATION : Heat Resisting Insulation)	-
5.1 (MATERIALS : FILLER AND INNER SHEATH)	-
5.2 (MATERIALS : FILLER AND INNER SHEATH)	-
6.1 (MATERIALS : ARMGURING)	-
7.1.1 (OUTER SHEATH : For Cables with General Purpose InsuIafion)	-
7.1.2 (OUTER SHEATH : For Cables with Heat Resisting InsuIalion)	-
8.1 (CONSTRUCTION : CONDUCTOR)	-
8.2 (CONSTRUCTION : CONDUCTOR)	-
9.1 (INSULATION )	-
9.3 (INSULATION :Tolerance on Thickness of Insulation)	-
9.4 (INSULATION : Application of Insulation)	-
10.1 (CORE IDENTIFICATION)	-
10.2 (CORE IDENTIFICATION)	-
10.3 (CORE IDENTIFICATION)	-
10.3.1 (Arrangement of Marking)	-
11.1 (LAYING UP OF CORES)	-
11.2 (LAYING UP OF CORES)	-
12.1 (INNER SHEATH)	-
12.2 (INNER SHEATH)	-
13.1.1 (ARMOURING : Application)	-
13.1.2 (Armouring: Coverage )	-
13.1.3 (ARMOURING : Direction of lay )	-
13.1.4 (ARMOURING : Application)	-
13.2 (ARMOURING : Type of Armour)	-
13.2.1 (ARMOURING : Type of Armour)	-
13.4 (ARMOURING : Joints)	-
13.5.2 (ARMOURING : Resistance)	-
13.6 b) (ARMOURING: Elongation )	-
13.6 e) (ARMOURING: Uniformity of zinc coating)	-
14.1 (OUTER SHEATH)	-
14.2 (OUTER SHEATH)	-
14.3 (OUTER SHEATH : Colour )	-
14.4.2 (Thickness of Outer Sheath : Armoured Cables)	-
15.1 a) 2) (Tensile test (for aluminium) - Before stranding )	-
15.1 a) 2) (Tensile test (for aluminium) - After stranding )	-
15.1 a) 3) (Tests on conductor : Wrapping test ( for aluminium ))	-
17.1 (IDENTIFICATION : Manufacturer’s Identification)	-
17.2 (IDENTIFICATION : Cable Identification)	-
17.2.1 (IDENTIFICATION : Cable Identification)	-
17.3 (IDENTIFICATION : Cable Code)	-
9.3 (Minimum Thickness of Reduce core insulation)	-
9.2 (Thickness of Reduce core insulation)	-
15.1 d)2) (Phyaical tests for insulation- Ageing in air Oven : Tensile Test)	-
15.1 d)2) (Phyaical tests for insulation - Ageing in air oven : Elongation )	-
15.1 d)1) (Physical tests for sheath : Tensile stregth )	-
15.1 d)1) (Physical tests for sheath : Elongation )	-

Partial

-
Test facility not available for tests as per Cl. 15.1.1 of C1 and C2 category

11142

BIS, Guwahati Branch Laboratory (GBL)

IS 1489 (Part 1) (2015)

Portland pozzolana cement - Specification: Part 1 fly Ash Based

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7 -Table 2-iii- b (Setting Time Final- 4031 Part 5)	-
7 -Table 2- iii- a (Setting Time Initial- 4031 Part 5)	-
7 -Table 2- ii- b (Expansion after aeration- 4031 Part 3)	-
7 -Table 2- ii- b (Expansion by Autoclave- 4031 Part 3)	-
7 -Table 2- ii- a (Expansion after aeration - 4031 Part 3)	-
7 -Table 2- ii- a (Expansion by Le Chatelier- 4031 Part 3)	-
7 -Table 2- i (Fineness 4031 Part 2)	-
7 -Table 2- vi (Drying Shrinkage- IS 4031 Part 10)	-
7 -Table 2- iv- a (Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-
7 -Table 2- iv- b (Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-
7 -Table 2- iv- c (Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-
6 - Table - 1 v (Chloride content - Cl 4.13 of IS 4032:1985)	-
6 - Table - 1 iv (Loss on ignition - Cl 7.1 of IS 4032:1985)	-
6 - Table - 1 iii (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-
6 - Table - 1 ii (Magnesia - Cl 7.2 of IS 4032:1985)	-
6 - Table - 1 i (Insoluble residue - Cl 7.4 of IS 4032:1985)	-
6 - Table - 1 vi ( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-

Partial

-
Partial test facility (Transverse Strength Test not available).

11143

BIS, Western Regional Laboratory (WRL)

IS 13334 : Part 1 (2014)

Skimmed milk powder - Specification: Part 1 standard grade (Second Revision)

- View breakup
Rs.10430/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.6 (Listeria monocytogenes)	-
5.6 (Spore count, Anaerobic (Sulfite reducing Clostridia))	-
5.6 (Spore count, Aerobic (Bacillus cereus))	-
5.6 (Salmonella)	-
5.6 (Coagulase positive Staphylococcus aureus)	-
5.6 (Escherichia coli)	-
5.6 (Coliform count )	-
5.6 (Bacterial count)	-
5.6 (Scorched particles)	-
5.6 (Milk fat)	-
5.6 (Titratable acidity (lactic acid))	-
5.6 (Total ash (on dry basis))	-
5.6 (Milk protein in milk solids not fat)	-
5.6 (Moisture)	-
5.2 (Absence of extraneous matter, added colour and added flavour)	-
4 (Description)	-
Cl 5.4 (The flavour of the product or of the reconstituted milk shall be pleasant and clean (see IS 10030).)	-
5.6 (Insolubility index)	-

Partial

-
(1) As per Cl. 5.7 The pesticide residues, heavy metals, toxins (aflatoxins and other naturally occurring toxins) and contaminants, if any, in the product shall not exceed the limits as prescribed in the Food Safety and Standards (Contaminants, Toxins and Residues) Regulations, 2011.’

11144

BIS, Guwahati Branch Laboratory (GBL)

IS 303 (1989)

Plywood for General Purposes -

BWR/MR

Rs 4000/- /BWR Grade, Rs.4900/- for MR Grade View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
11.4, Table 4 (Static Bending Strength - Modulus of Rupture - Across the Face Grain - Minimum Individual)	-
11.4, Table 4 (Static Bending Strength - Modulus of Rupture - Across the Face Grain - Average)	-
11.4, Table 4 (Static Bending Strength - Modulus of Rupture - Along the Face Grain - Minimum Individual)	-
11.4, Table 4 (Static Bending Strength - Modulus of Rupture - Along the Face Grain - Average)	-
11.4, Table 4 (Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Minimum Individual)	-
11.4, Table 4 (Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Average)	-
11.4, Table 4 (Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Minimum Individual)	-
11.4, Table 4 (Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average)	-
11.2.2 (Glue Adhesion - Mycological test - 11.2.2, Part 7 of IS 1734 [for MR Garde only])	-
11.2.1 (Glue Adhesion - Water resistance test - 11.2.1.1 [for MR Grade])	-
11.2.1 (Glue Adhesion - Water resistance test - 11.2.1.1 [for BWR Grade])	-
11.3 (Moisture Content - Part 1 of IS 1734)	-
8 (Dimensions & Tolerances - Edge Straightness - Annexure C)	-
8 (Dimensions & Tolerances - Squareness - Annexure C)	-
8 (Dimensions & Tolerances - Thickness - Cl. 8)	-
8 (Dimensions & Tolerances - Width - Cl. 8)	-
8 (Dimensions & Tolerances - Length - Cl. 8)	-
5.2, Table 1, Table 2 (Quality Requirements - Cl. 5.2)	-
5.1 (Type - For BB Type)	-
5.1 (Type - For AB Type)	-
5.1 (Type - For AA Type)	-
4 (Grade - For MR grade)	-
4 (Grade - For BWR grade)	-
9 (Workmanship and Finish - Cl.9, 8.3, Annexure C)	-
9 (Workmanship and Finish - Cl.9, 8.3, Annexure C)	-
cl. 13.1 (marking)	-
cl. 13.2 (marking)	-

Partial

-
-

11145

BIS, Bengaluru Branch Laboratory (BNBL)

IS 455 (2015)

Portland slag cement - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 - Table - 1 i (Insoluble residue - Cl 6.9 of IS 4032:1985)	-
6 - Table - 1 ii (Magnesia - Cl 6.8 of IS 4032:1985)	-
6 - Table - 1 iii (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 6.11 of IS 4032:1985)	-
6 - Table - 1 iv (Sulphide sulphur (S) - Cl 6.12 of IS 4032:1985)	-
6 - Table - 1 v (Loss on ignition - Cl 6.2 of IS 4032:1985)	-
6 - Table - 1 vi (Chloride content - Cl 4.13 of IS 4032:1985)	-
6 - Table - 1 vii ( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-
7 Table 1 iv c (Compretsive Strenqth 672 ± 4 hr IS 4031(Part 6))	-
7 Table 1 iv b (Compretsive Strenqth 168 ± 2 hr IS 4031(Part 6))	-
7 Table 1 iv a (Compretsive Strenqth .72 ± 1 hr IS 4031(Part 6))	-
7 Table 1 iii b (Setting Time ( by Vicat Apparatus ), Final IS 4031(Part 5))	-
7 Table 1 iii a (Setting Time ( by Vicat Apparatus ),Initial IS 4031(Part 5))	-
7 Table 1 ii b (Soundness, Autoclave expansion IS 4031(Part 3) )	-
7 Table 1 ii a (Soundness, Le-Chate1ier expansion IS 4031(Part 3) )	-
7 Table 1 i (Fineness IS 4031(Part 2))	-

Partial

-
Expect Transverse Strength

11146

BIS, Western Regional Laboratory (WRL)

IS 2347 (2017)

Domestic pressure cooker - Specification (Sixth Revision)

- View breakup
Rs. 14700/- excluding test on handles and chemical tests.

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Capacity )	-
6.1.1 (Pressure Regulating Device)	-
6.1.5 (Pressure Regulating Device)	-
8.1 (Air Pressure Test)	-
8.2 (Proof Pressure Test)	-
8.3 (Operating Test for Pressure Regulating Device)	-
8.4 (Test for Safety Pressure Relief Device)	-
8.5 (Bursting Pressure Test)	-
8.6.1 (Tests for Removal of Lid under Pressure For Outer Lid Cooker)	-
8.6.2 (Tests for Removal of Lid under Pressure For inner Lid Cooker)	-
6.1.2 (Pressure Regulating Device)	-
6.1.3 (Pressure Regulating Device)	-
6.1.4 (Pressure Regulating Device)	-
6.2 (Safety Relief Device)	-
6.2.1 (Safety Relief Device)	-
6.3.1 (Temperature Responsive Pressure Relief Device)	-
6.4.1 (Handles and Knobs)	-
7.1 (WORKMANSHIP AND FINISH)	-
7.2 (WORKMANSHIP AND FINISH)	-
7.3 (WORKMANSHIP AND FINISH)	-
7.4 (WORKMANSHIP AND FINISH)	-
8.14 (3 Ply Construction Cooker Body)	-
6 (CONSTRUCTION)	-
6.1 (Pressure Regulating Device)	-
6.2 NOTE (Construction-Safety Relief Device)	-
11 (Marking)	-

Partial

-
The following test facilities are not available: (1) Material as per Clause 5.1, 5.2, 5.5, 5.6, 5.7, 5.8, 5.9, 5.10, 5.11 (2) Test for Hard Anodized Surface. (3) Test for spring-loaded mechanism (4) Test for handle and knob. (5) Electrical Pressure cooker

11147

BIS, Western Regional Laboratory (WRL)

IS 2124 (2000)

Sodium bicarbonate - Specification (Second Revision)

Rs 4660/- for Pure Grade View breakup
Rs 8210/- for Analytical Reagent Grade Rs 4360/- for Refined Grade

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (Grade)	-
4.1 (Description)	-
4.2 (Table 1 S.no.(i)) (Total Alkalinity (as NaHCO3))	-
4.2 (Table 1 S.no.(i)) (pH )	-
4.2 (Table 1 S.no.(ii)) (Chlorides (as Cl))	-
4.2 (Table 1 S.no.(iii)) (Insoluble matter)	-
4.2 (Table 1 S.no.(iv)) (Sulphates (as SO4))	-
4.2 (Table 1 S.no.(v)) (Iron (as Fe))	-
4.2 (Table 1 S.no.(vii)) (Arsenic (as As))	-
4.2 (Table 1 S.no.(viii)) (Ammonium compounds (as NH4))	-
4.2 (Table 1 S.no.(ix)) (Phosphates (as PO4))	-
4.2 (Table 1 S.no.(x)) (Calcium and magnesium (as Ca))	-
4.2 (Table 1 S.no.(xi)) (Copper (as Cu))	-
4.2 (Table 1 S.no.(xii)) (Nitrates (as NO3))	-
4.2 (Table 1 S.no.(xiii)) (Silicates (as SiOz))	-
4.2 (Table 1 S.no.(xiv)) (Potassium (as K))	-
4.2 (Table 1 S.no.(xv)) (Substances reducing iodine)	-

Complete

-
-

11148

BIS, Western Regional Laboratory (WRL)

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.2.1 (6.1.1 Identification Stripes)	-
7.4 table -3 & 4 (6.1 Dimensions)	-
8.2 (Longitudinal Reversion Test)	-
8.4 ( Melt Flow Rate)	-
8.3 (Carbon black)	-
6.2 (Colour)	-
6, 6.1 (PIPE DESCRIPTION)	-
7 ()	-
Clause 8.3 (Carbon Black Dispersion)	-
8.5 (Oxidation Induction Time)	-
8.7 (Density)	-
8.9 table-6 (Elongation at Break)	-

Partial

-
The following test facilities are not available: (1)Internal Pressure creep rupture test (2)Tensile Strength for Butt-fusion (Clause 8.8) (3) Slow Crack Growth rate test (Clause 8.10) (4) Depth of strip (Clause 6.2.1) (5) Overall Migration (Clause 8.6) (6) Carbon Black content ( Clause 8.3) (7) For Size above 250 mm

11149

BIS, Guwahati Branch Laboratory (GBL)

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 11.3 (Press)	-
Cl 7 (Workmanship)	-
Cl 18 (Weight)	-
Cl. 10.3 (Cl. 10.3 (Elongation %))	-
Cl. 10.3 (Cl. 10.3 (Yield Stress))	-
Cl 15 (Length, Width & Thickness)	-
Cl. 10.3 (Cl. 10.3 (Tensile Strength))	-
Cl. 15, 16 (Leg Length A (Angle))	-
Cl. 15, 16 (Leg Length B (Angle))	-
Cl. 15, 16 (Thickness )	-
Cl. 15, 16 (Toe Radius R2)	-
Cl. 15, 16 (Out of Square (Angle))	-
Cl. 15, 16 (Leg Length Difference (Angle))	-
Cl. 15 (Cl. 15 Channel Section: Sweep)	-
Cl. 15 (Cl. 15 Channel Section: Camber)	-
Cl. 15 (Cl. 15 Channel Section: Flatness of Web (Concavity))	-
Cl. 15 (Cl. 15 Channel Section: Flatness of Web (Convexity))	-
Cl. 15 (Cl. 15 Round Bar: Out of Shape)	-
Cl. 15 (Cl. 15 Channel Section: Width of Flange)	-
Cl. 15 (Cl. 15 Channel Section: Depth)	-
Cl. 15 (Cl. 15 Square Bar: Out of Square)	-
Cl. 15 (Cl. 15 Square Bar: Side Width: Minimum)	-
Cl. 15 (Cl. 15 Square Bar: Side Width: Maximum)	-
Cl. 15 (Cl. 15 Round Bar: Out of Shape)	-
Cl. 15 (Cl. 15 Round Bar: Diameter Minimum)	-
Cl. 15 (Cl. 15 Round Bar: Diameter Maximum)	-
Cl. 15, 16 (Off Centre of Web)	-
Cl. 15, 16 (Width of flange (I Beam))	-
Cl. 15, 16 (Depth (I Beam))	-
Cl. 15, 16 (Flange Slope)	-
Cl. 15, 16 (Out of Square (Flat))	-
Cl. 15, 16 (Web Thickness)	-
Cl. 15, 16 (Flange Thickness)	-
Cl. 15, 16 (Flange out of square (I beam))	-
Clause 15, Table 4 (IS 2062)	-
16 (Tolerance)	-
Clause 15, Table 4 (IS 2062)	-
Cl. 15, 16 (Root Radius R1)	-
15 (Radius R1)	-
Cl. 15, 16 (Root Radius R1)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-

Partial

-
Mech- Except Y groove crackability, Impact test, NDT, grain size

11150

BIS, Western Regional Laboratory (WRL)

IS 14543 (2016)

Packaged drinking water (Other Than Packaged Natural Mineral Water) - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.3 Table-1vi (pH)	-
5.3 Table-1 v (Total dissolved solids)	-
5.3 Table-1 iv (Turbidity)	-
5.3 Table-1 iii (Taste)	-
5.3 Table-1 ii (Odour)	-
5.3 Table-1 i (Colour)	-
5.3 (Description)	-
5.2.9 (Vibrio parahaemolyticus)	-
5.2.9 (Vibrio cholera)	-
5.2.8 (Shigella)	-
5.2.8 (Salmonella)	-
5.2.7 (Yeast and Mould)	-
5.2.6 (Aerobic Microbial Count at 37°C)	-
5.2.6 (Aerobic Microbial Count at 20-22°C)	-
5.2.5 (Pseudomonas Aeruginosa)	-
5.2.4 (Sulphite Reducing Anaerobes)	-
5.2.3 (Staphylococcus Aureus)	-
5.2.3 (Faecal Streptococci)	-
5.2.2 (Coliform)	-
5.2.1 (Escherichia coli (or thermotolerant bacteria))	-
5.3 Table-2 xi (Chloride (as Cl))	-
5.3 Table-2 xiv (Alkaliniity (as HCO3))	-
5.3 Table-2 i (Barium (as Ba))	-
5.3 Table-2 ii (Copper (as Cu))	-
5.3 Table-2 iii (Iron (as Fe),)	-
5.3 Table-2 iv (Manganese (as Mn))	-
5.3 Table-2 viii (Zinc (as Zn))	-
5.3 Table-2 ix (Silver (as Ag))	-
5.3 Table-2 x (Aluminium (as Al))	-
5.3 Table-2 xii (Selenium (as Se),)	-
5.3 Table-2 xxiii (Antimony (as Sb))	-
5.3 Table-2 xxiv (Borates (as B))	-
5.3 Table-3 i (Mercury (as Hg))	-
5.3 Table-3 ii (Cadmium (as Cd))	-
5.3 Table-3 iii (Arsenic (as As))	-
5.3 Table-3 v (Lead (as Pb))	-
5.3 Table-3 vi (Chromium (as Cr))	-
5.3 Table-3 vii (Nickel (as Ni))	-
5.3 Table-2 vi (Nitrite (as NO2))	-
5.3 Table-2 v (Nitrate (as NO3))	-
5.3 Table-2 xiii (Sulphate (as SO4),)	-
5.3 Table-2 xviii (Residual free chlorine)	-
5.3 Table-2 xxv (Bromates (as BrO3),)	-
5.3 Table-2vii (Fluoride (as F))	-
5.3 Table-2 xvii (Sodium (as Na))	-
5.3 Table-2 xvi (Magnesium (as Mg))	-
5.3 Table-2 xv (Calcium (as Ca),)	-
Table 3, x) (Uranium)	-
5.4 ii) (Total pesticied residue)	-
5.4 i) (Dieldrin)	-
5.4 i) (Aldrin)	-
5.4 i) (Malathion)	-
5.4 i) (Methyl Paraoxon)	-
5.4 i) (Methyl Parathion)	-
5.4 i) (Atrazine)	-
5.4 i) (Alachlor)	-
5.4 i) (Isoproturon)	-
5.4 i) (Butachlor)	-
5.4 i) (2,4-D)	-
5.4 i) (phorate sulphone)	-
5.4 i) (Phorate sulphoxide)	-
5.4 i) (Phorate)	-
5.4 i) (Chlorpyrifos)	-
5.4 i) (Monocrotophos)	-
5.4 i) (Endosulfan Sulphate)	-
5.4 i) (beta-Endosulfan)	-
5.4 i) (alpha-Endosulfan)	-
5.4 i) (Delta-HCH)	-
5.4 i) (beta-HCH)	-
5.4 i) (alpha-HCH)	-
5.4 i) (Gamma-HCH (Lindane))	-
5.4 i) (p,p DDD)	-
5.4 i) (o,p DDD)	-
5.4 i) (p,p DDE)	-
5.4 i) (o,p DDE)	-
5.4 i) (p,p DDT)	-
5.4 i) (o,p DDT)	-
5.3 Table-3 ix (Polynuclear aromatic hydrocarbons)	-
5.3 Table-3 viii (Polychlorinated biphenyle (PCB))	-
5.3 Table-2 xxii (Sulphide (as H2S))	-
5.3 Table-2 xx (Mineral oil)	-
5.3 Table-2 xxi (Anionic surface active agents (as MBAS))	-
5.3 Table-2 xix (Phenolic compounds (as C6H5OH))	-
5.4 i) (Ethion)	-
5.4 i) (Malaoxon)	-

Partial

-
Excluding Cyanide, Radio Active Elements. For testing of Pesticide Residues please indicate accordingly

11151

BIS, Guwahati Branch Laboratory (GBL)

IS 1659 (2004)

Block boards - Specification (Fourth Revision)

MR/BWP

- View breakup
Rs 5900/- for BWR Grade, Rs.6800/- for MR grade

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
9.2.5 (Modulus of elasticity - MINIMUM INDIVIDUAL - Annexure K)	-
9.2.4 (Mycological Test [for MR grade only] - Annexure J)	-
9.2.3 (Adhesion of Plies - Annexure H)	-
9.2.2 (Resistance to water - Annexure G, Annexure H [For MR Grade])	-
9.2.2 (Resistance to water - Annexure G, Annexure H [For BWP grade])	-
9.2.1 (Dimensional Changes caused by humidity Change in local planeness - Annexure F)	-
9.2.1 (Dimensional Changes caused by humidity - Delamination - Annexure F)	-
9.2.1 (Dimensional Changes caused by humidity - Change in thickness - at 40% RH - Annexure F)	-
9.2.1 (Dimensional Changes caused by humidity - Change in Thickness - at 90% RH - Annexure F)	-
9.2.1 (Dimensional Changes caused by humidity - Change in Length - at 40% RH - Annexure F)	-
9.2.1 (Dimensional Changes caused by humidity - Change in Length - at 90% RH - Annexure F)	-
7.3 (Dimensional Requirements - Variation in thickness - Annexure E)	-
7.3 (Dimensional Requirements - Squareness - Annexure D)	-
7.3 (Dimensional Requirements - Edge Straightness - Annexure D)	-
7.3 (Dimensional Requirements - Thickness - Annexure E)	-
7.3 (Dimensional Requirements - Width - 8.1.4)	-
7.3 (Dimensional Requirements - Length - 8.1.4)	-
9.2.5 (Modulus of elasticity - AVERAGE - Annexure K)	-
9.2.5 (Modulus of rupture - MINIMUM INDIVIDUAL - Annexure K)	-
9.2.5 (Modulus of rupture - AVERAGE - Annexure K)	-
9.2.6 (Spot test - Annexure L)	-
8.1.3, 6.3.3, IS 1328 (Visual Inspection - Permissible Defects - IS 1328 [test method for DECORATIVE type])	-
8.1.3, 6.3.3, IS 303 (Visual Inspection - Permissible Defects - IS 303 [test method for COMMERCIAL type])	-
cl. 11 (marking)	-
cl. 11.1 (marking - BIS certification marking)	-
9.2.6 (mechanical) (Spot test - Annexure L)	-

Partial

-
-

11152

BIS, Southern Regional Laboratory (SRL)

IS 14543 (2016)

Packaged drinking water (Other Than Packaged Natural Mineral Water) - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.3 Table-1 i (Colour)	-
5.3 Table-1 iv (Turbidity)	-
5.3 Table-1 v (Total dissolved solids)	-
5.3 Table-1vi (pH)	-
5.3 Table-2 i (Barium (as Ba))	-
5.3 Table-2 ii (Copper (as Cu))	-
5.3 Table-2 iii (Iron (as Fe),)	-
5.3 Table-2 iv (Manganese (as Mn))	-
5.3 Table-2 vi (Nitrite (as NO2))	-
5.3 Table-2vii (Fluoride (as F))	-
5.3 Table-2 viii (Zinc (as Zn))	-
5.3 Table-2 ix (Silver (as Ag))	-
5.3 Table-2 x (Aluminium (as Al))	-
5.3 Table-2 xi (Chloride (as Cl))	-
5.3 Table-2 xii (Selenium (as Se),)	-
5.3 Table-2 xiv (Alkaliniity (as HCO3))	-
5.3 Table-2 xv (Calcium (as Ca),)	-
5.3 Table-2 xvi (Magnesium (as Mg))	-
5.3 Table-2 xvii (Sodium (as Na))	-
5.3 Table-2 xx (Mineral oil)	-
5.3 Table-2 xxii (Sulphide (as H2S))	-
5.3 Table-2 xxiii (Antimony (as Sb))	-
5.3 Table-2 xxv (Bromates (as BrO3),)	-
5.3 Table-3 i (Mercury (as Hg))	-
5.3 Table-3 ii (Cadmium (as Cd))	-
5.3 Table-3 iii (Arsenic (as As))	-
5.3 Table-3 v (Lead (as Pb))	-
5.3 Table-3 vi (Chromium (as Cr))	-
5.3 Table-3 vii (Nickel (as Ni))	-
5.3 Table-1 ii (Odour)	-
5.3 Table-1 iii (Taste)	-
5.3 (Description)	-
5.2.1 (Escherichia coli (or thermotolerant bacteria))	-
5.2.2 (Coliform)	-
5.2.3 (Faecal Streptococci)	-
5.2.3 (Staphylococcus Aureus)	-
5.2.4 (Sulphite Reducing Anaerobes)	-
5.2.5 (Pseudomonas Aeruginosa)	-
5.2.6 (Aerobic Microbial Count at 20-22°C)	-
5.2.6 (Aerobic Microbial Count at 37°C)	-
5.2.7 (Yeast and Mould)	-
5.2.8 (Salmonella)	-
5.2.8 (Shigella)	-
5.2.9 (Vibrio cholera)	-
5.2.9 (Vibrio parahaemolyticus)	-
Table 3, x) (Uranium)	-
5.4 ii) (Total pesticied residue)	-
5.4 i) (Dieldrin)	-
5.4 i) (Aldrin)	-
5.4 i) (Malaoxon)	-
5.4 i) (Malathion)	-
5.4 i) (Methyl Paraoxon)	-
5.4 i) (Methyl Parathion)	-
5.4 i) (Atrazine)	-
5.4 i) (Alachlor)	-
5.4 i) (Isoproturon)	-
5.4 i) (Butachlor)	-
5.4 i) (2,4-D)	-
5.4 i) (phorate sulphone)	-
5.4 i) (Phorate sulphoxide)	-
5.4 i) (Phorate)	-
5.4 i) (Chlorpyrifos)	-
5.4 i) (Ethion)	-
5.4 i) (Monocrotophos)	-
5.4 i) (Endosulfan Sulphate)	-
5.4 i) (beta-Endosulfan)	-
5.4 i) (alpha-Endosulfan)	-
5.4 i) (Delta-HCH)	-
5.4 i) (beta-HCH)	-
5.4 i) (alpha-HCH)	-
5.4 i) (Gamma-HCH (Lindane))	-
5.4 i) (p,p DDD)	-
5.4 i) (o,p DDD)	-
5.4 i) (p,p DDE)	-
5.4 i) (o,p DDE)	-
5.4 i) (p,p DDT)	-
5.4 i) (o,p DDT)	-
5.3 Table-3 ix (Polynuclear aromatic hydrocarbons)	-
5.3 Table-3 viii (Polychlorinated biphenyle (PCB))	-
5.3 Table-2 xxiv (Borates (as B))	-
5.3 Table-2 xviii (Residual free chlorine)	-

Partial

-
52x500ml; 26x1 ltr; 7x2ltr; 5x5 ltr; 2x20ltr excluding tests for radio active residues, Cyanide, PAH, mbas, Phenolic compounds, Microbiology - Complete

11153

BIS Patna Branch Laboratory (PBL)

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 7 (Workmanship)	-
Clause - 5, 8.1 & 8.2 (E250, CARBON)	-
Clause - 5, 8.1 & 8.2 (E250, SULPHUR)	-
Clause - 5, 8.1 & 8.2 (E250, PHOSPHURS)	-
Clause - 5, 8.1 & 8.2 (E250 ,MANGANESE)	-
Clause - 5, 8.1 & 8.2 (E250, NITROGEN)	-
Clause - 5, 8.1 & 8.2 (E250, SILICON)	-
Clause - 5, 8.1 & 8.2 (E250, CARBON +EQUIVELENT )	-
Cl. 10.3 (Cl. 10.3 (Tensile Strength))	-
Cl. 10.3 (Cl. 10.3 (Yield Stress))	-
Cl. 10.3 (Cl. 10.3 (Elongation %))	-
Cl 18 (Weight)	-
Cl 15 (Length, Width & Thickness)	-
Cl 11.3 (Press)	-
Cl 12 (Sudden Load Applied)	-

Partial

-
All test facilities are available as per the IS except- i. Y-Groove Test (Clause 13) ii. Bend Test for thickness above 25 mm (Clause 11) iii. Tests for microalloying elements and Cr, Mo, Ni, Cu Al and B (Clause 8.2) Note: Prepared test piece of size 55 mm x10 mm x10 mm is required for Impact Test (Clause 12) *- The exact sample type, size and quantity may be ascertained from the latest product manual issued by BIS.

11154

BIS Patna Branch Laboratory (PBL)

IS 1786 (2008)

High strength deformed steel bars and wires for concretere inforcement - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5 (Deformations and Surface Characteristics)	-
Clause - 4.2 & 4.2.1 (Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 CARBON +EQUIVELENT )	-
Cl.9.4 & Cl. 9.4.1 (Rebend test)	-
Cl. 9.3, Table 4 (Bend Test )	-
Cl. 8.1 Table 3 (Elongation, percentage)	-
Cl. 8.1 Table 3 (TS/YS ratio)	-
Cl. 8.1 Table 3 (Tensile Strength (TS))	-
Cl. 8.1 Table 3 (Yield Stress (YS))	-
Cl. 7.2 Table -2 (Nominal Mass)	-
Cl. 6.1 (Nominal Size)	-
Cl. 5 (Cl. 5 - Mean projected area of transverse ribs (1/3 of Ar))	-
Cl. 5 (Cl.5 Mean area of ribs/unit length (Ar), )	-
Clause - 4.2 & 4.2.1 (Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 SULPHUR+PHOSPHUR)	-
Clause - 4.2 & 4.2.1 (Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 MANGANESE)	-
Clause - 4.2 & 4.2.1 (Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 NITROGEN)	-
Clause - 4.2 & 4.2.1 (Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 PHOSPHURS)	-
Clause - 4.2 & 4.2.1 (Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 SULPHUR)	-
Clause - 4.2 & 4.2.1 (Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 CARBON )	-
Cl. 5.3 (a) (The ribs contributing the projected area - Longitudinal Ribs)	-
Cl. 5.3 (b) (The ribs contributing the projected area - Transverse Ribs)	-

Partial

-
All test facilities are available as per the IS except- i. Bond/Pull Out Test (Clause 5.7) ii. Total Elongation at Maximum Force (Clause 8.1 and Table 3) iii. Tensile Test of Sizes > 16mm (Clause 8.1 and Table 3) iv. Tests for microalloying elements (Ti, Nb, B, V), Cr, Mo, Cu, Ni and Al (Clause 4.2)

11155

BIS Patna Branch Laboratory (PBL)

IS 1489 (Part 1) (2015)

Portland pozzolana cement - Specification: Part 1 fly Ash Based

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7 -Table 2- vi (Drying Shrinkage- IS 4031 Part 10)	-
7 -Table 2- iv- c (Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-
7 -Table 2- iv- b (Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-
7 -Table 2- iv- a (Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-
7 -Table 2-iii- b (Setting Time Final- 4031 Part 5)	-
7 -Table 2- iii- a (Setting Time Initial- 4031 Part 5)	-
7 -Table 2- ii- b (Expansion by Autoclave- 4031 Part 3)	-
7 -Table 2- ii- a (Expansion by Le Chatelier- 4031 Part 3)	-
7 -Table 2- i (Fineness 4031 Part 2)	-
6 - Table - 1 vi ( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-
6 - Table - 1 v (Chloride content - Cl 4.13 of IS 4032:1985)	-
6 - Table - 1 iv (Loss on ignition - Cl 7.1 of IS 4032:1985)	-
6 - Table - 1 iii (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-
6 - Table - 1 ii (Magnesia - Cl 7.2 of IS 4032:1985)	-
6 - Table - 1 i (Insoluble residue - Cl 7.4 of IS 4032:1985)	-
7 -Table 2- ii- a (Expansion after aeration - 4031 Part 3)	-
7 -Table 2- ii- b (Expansion after aeration- 4031 Part 3)	-
7 -Table 2- ii- a (Expansion after aeration - 4031 Part 3)	-

Partial

-
All test facilities are available as per the IS except Transverse Strength Test (Clause 7 and Table-2) which is an optional test

11156

BIS Patna Branch Laboratory (PBL)

IS 1659 (2004)

Block boards - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.3 (Dimensional Requirements - Variation in thickness - Annexure E)	-
7.3 (Dimensional Requirements - Squareness - Annexure D)	-
7.3 (Dimensional Requirements - Edge Straightness - Annexure D)	-
7.3 (Dimensional Requirements - Thickness - Annexure E)	-
7.3 (Dimensional Requirements - Width - 8.1.4)	-
7.3 (Dimensional Requirements - Length - 8.1.4)	-
9.2.5 (Modulus of elasticity - MINIMUM INDIVIDUAL - Annexure K)	-
9.2.5 (Modulus of elasticity - AVERAGE - Annexure K)	-
9.2.5 (Modulus of rupture - MINIMUM INDIVIDUAL - Annexure K)	-
9.2.5 (Modulus of rupture - AVERAGE - Annexure K)	-
9.2.4 (Mycological Test [for MR grade only] - Annexure J)	-
9.2.3 (Adhesion of Plies - Annexure H)	-
9.2.2 (Resistance to water - Annexure G, Annexure H [For MR Grade])	-
9.2.2 (Resistance to water - Annexure G, Annexure H [For BWP grade])	-
9.2.1 (Dimensional Changes caused by humidity Change in local planeness - Annexure F)	-
9.2.1 (Dimensional Changes caused by humidity - Delamination - Annexure F)	-
9.2.1 (Dimensional Changes caused by humidity - Change in thickness - at 40% RH - Annexure F)	-
9.2.1 (Dimensional Changes caused by humidity - Change in Thickness - at 90% RH - Annexure F)	-
9.2.1 (Dimensional Changes caused by humidity - Change in Length - at 40% RH - Annexure F)	-
9.2.1 (Dimensional Changes caused by humidity - Change in Length - at 90% RH - Annexure F)	-
8.1.3, 6.3.3, IS 1328 (Visual Inspection - Permissible Defects - IS 1328 [test method for DECORATIVE type])	-
8.1.3, 6.3.3, IS 303 (Visual Inspection - Permissible Defects - IS 303 [test method for COMMERCIAL type])	-
9.2.6 (mechanical) (Spot test - Annexure L)	-

Partial

-
All test facilities are available as per the IS

11157

BIS Patna Branch Laboratory (PBL)

IS 303 (1989)

Plywood for General Purposes -

Rs 4000/- /BWR Grade, Rs.4900/- for MR Grade View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
11.4, Table 4 (Static Bending Strength - Modulus of Rupture - Across the Face Grain - Minimum Individual)	-
11.4, Table 4 (Static Bending Strength - Modulus of Rupture - Across the Face Grain - Average)	-
11.4, Table 4 (Static Bending Strength - Modulus of Rupture - Along the Face Grain - Minimum Individual)	-
11.4, Table 4 (Static Bending Strength - Modulus of Rupture - Along the Face Grain - Average)	-
11.4, Table 4 (Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Minimum Individual)	-
11.4, Table 4 (Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Average)	-
11.4, Table 4 (Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Minimum Individual)	-
11.4, Table 4 (Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average)	-
11.2.2 (Glue Adhesion - Mycological test - 11.2.2, Part 7 of IS 1734 [for MR Garde only])	-
11.2.1 (Glue Adhesion - Water resistance test - 11.2.1.1 [for MR Grade])	-
11.2.1 (Glue Adhesion - Water resistance test - 11.2.1.1 [for BWR Grade])	-
11.3 (Moisture Content - Part 1 of IS 1734)	-
8 (Dimensions & Tolerances - Edge Straightness - Annexure C)	-
8 (Dimensions & Tolerances - Squareness - Annexure C)	-
8 (Dimensions & Tolerances - Thickness - Cl. 8)	-
8 (Dimensions & Tolerances - Width - Cl. 8)	-
8 (Dimensions & Tolerances - Length - Cl. 8)	-
9 (Workmanship and Finish - Cl.9, 8.3, Annexure C)	-
9 (Workmanship and Finish - Cl.9, 8.3, Annexure C)	-
5.2, Table 1, Table 2 (Quality Requirements - Cl. 5.2)	-
5.1 (Type - For BB Type)	-
5.1 (Type - For AB Type)	-
5.1 (Type - For AA Type)	-
4 (Grade - For MR grade)	-
4 (Grade - For BWR grade)	-
cl. 13.1 (marking)	-
cl. 13.2 (marking)	-

Partial

-
All test facilities are available as per the IS

11158

BIS Patna Branch Laboratory (PBL)

IS 269 (2015)

Ordinary portland cement - Specification (Sixth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7 Table-3 iv c (Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-
7 Table-3 iv b (Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-
7 Table-3 iv a (Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-
7 Table-3 iii b (Setting Time Final)	-
7 Table-3 iii a (Setting Time Initial)	-
7 Table-3 ii b (Expansion by Autoclave)	-
7 Table-3 ii a (Expansion by Le Chatelier)	-
7 Table-3 i. (Fineness)	-
6.1 Table-2 viii (Alkali content)	-
6.1 Table-2 vii (Chloride content)	-
6.1 Table-2 vi (Loss on ignition)	-
6.1 Table-2 v (Total Sulphur Content calculated as Sulphuric Anhydride)	-
6.1 Table-2 iv (Magnesia)	-
6.1 Table-2 iii. (Insoluble residue)	-
7 Table-3 ii b (Expansion after aeration)	-
7 Table-3 ii a (Expansion after aeration)	-
6.1 Table-2 ii. (Ratio of percentage of alumina to that of iron oxide)	-
6 - Table - 1 i (Ratio of percentage of lime to percentages of silica, alumina and iron oxide - Cl 4 of IS 4032:1985)	-

Partial

-
All test facilities are available as per the IS except Transverse Strength Test (Clause 7 and Table-3) which is an optional test

11159

BIS Patna Branch Laboratory (PBL)

IS 455 (2015)

Portland slag cement - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7 Table 1 iv c (Compretsive Strenqth 672 ± 4 hr IS 4031(Part 6))	-
7 Table 1 iv b (Compretsive Strenqth 168 ± 2 hr IS 4031(Part 6))	-
7 Table 1 iv a (Compretsive Strenqth .72 ± 1 hr IS 4031(Part 6))	-
7 Table 1 iii b (Setting Time ( by Vicat Apparatus ), Final IS 4031(Part 5))	-
7 Table 1 iii a (Setting Time ( by Vicat Apparatus ),Initial IS 4031(Part 5))	-
7 Table 1 ii b (Soundness, Autoclave expansion IS 4031(Part 3) )	-
7 Table 1 ii a (Soundness, Le-Chate1ier expansion IS 4031(Part 3) )	-
7 Table 1 i (Fineness IS 4031(Part 2))	-
6 - Table - 1 vii ( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-
6 - Table - 1 vi (Chloride content - Cl 4.13 of IS 4032:1985)	-
6 - Table - 1 v (Loss on ignition - Cl 6.2 of IS 4032:1985)	-
6 - Table - 1 iv (Sulphide sulphur (S) - Cl 6.12 of IS 4032:1985)	-
6 - Table - 1 iii (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 6.11 of IS 4032:1985)	-
6 - Table - 1 ii (Magnesia - Cl 6.8 of IS 4032:1985)	-
6 - Table - 1 i (Insoluble residue - Cl 6.9 of IS 4032:1985)	-
Cl. 7 Table-2 (Cl. 7 Table-2 ii a (Expansion after aeration ))	-
Cl. 7 Table-2 (Cl. 7 Table-2 ii b (Expansion after aeration ))	-

Partial

-
All test facilities are available as per the IS except Transverse Strength Test (Clause 7 and Table 2) which is an optional test

11160

BIS Patna Branch Laboratory (PBL)

IS 12818 (2010)

Unplasticized polyvinyl chloride (Pvc - U) screen and casing pipes for bore/tubewells - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
9.5 (Tensile Strength IS 12235(Part 13))	-
9.2 (Internal Diameter)	-
9.3 (Density IS 12235 (Part 14))	-
9.1 ( Visual Appearance)	-
5 (COLOUR)	-
7.2 and Table 5, 6 & 7 Fig 1B (Wall thickness, Max)	-
7.2 and Table 5, 6 & 7 Fig 1B (Wall thickness, Min)	-
7.2 and Table 5, 6 & 7 Fig 1B (Mean Outer Diameter over Connection)	-
7.2 and Table 5, 6 & 7 Fig 1B (Outer Diameter at any point, Max)	-
7.2 and Table 5, 6 & 7 Fig 1B (Outer Diameter at any point , Min)	-
7.2 and Table 5, 6 & 7 Fig 1B (Mean Outer Diameter of Pipe , Max)	-
7.2 and Table 5, 6 & 7 Fig 1B (Mean Outer Diameter of Pipe, Min)	-
7.2 and Table 5, 6 & 7 Fig 1B (Nominal Diameter)	-
7.2 and Table 5, 6 & 7 Fig 1B (DIMENSIONS - Casing Pipes)	-
8.4 (Sealing rings - Hardness)	-
9.6 (Vicat Softening Temperature IS 12235 (Part 2).)	-
9.4 and Table 14 (Resistance to External Blows at 0 ?C IS 12235 (Part 9))	-
8.1 to 8.3 and Table 11 &12 Fig 3A & 4A (THREADING OF SCREEN ANDCASING PIPES. IS 554.)	-

Partial

-
All test facilities available except Effect on Water (Clause 9.7)

Bureau of Indian Standards

The National Standards Body of India

Search by IS Number