BIS - LIMS (Laboratory Information Management System)

Search by IS Number

Reset

15123 Results

S.No.

Lab Name

Osl Code

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

14941

BIS, Central Laboratory (CL)

None

IS 1489 : Part 2 (2015)

Portland - Pozzolana cement - Specification: Part 2 calcined clay based

Rs.8420/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7 -Table 2- i (Fineness 4031 Part 2)	-
7 -Table 2- ii- a (Expansion by Le Chatelier- 4031 Part 3)	-
7 -Table 2- ii- b (Expansion by Autoclave- 4031 Part 3)	-
7 -Table 2- iii- a (Setting Time Initial- 4031 Part 5)	-
7 -Table 2-iii- b (Setting Time Final- 4031 Part 5)	-
7 -Table 2- iv- a (Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-
7 -Table 2- iv- b (Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-
7 -Table 2- iv- c (Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-
7 -Table 2- vi (Drying Shrinkage- IS 4031 Part 10)	-
6 - Table - 1 i (Insoluble residue - Cl 7.4 of IS 4032:1985)	-
6 - Table - 1 ii (Magnesia - Cl 7.2 of IS 4032:1985)	-
6 - Table - 1 iii (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-
6 - Table - 1 iv (Loss on ignition - Cl 7.1 of IS 4032:1985)	-
6 - Table - 1 v (Chloride content - Cl 4.13 of IS 4032:1985)	-
6 - Table - 1 vi ( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-

-
Excluding Table 1,Clause 6.1 ,sl. no.(vi) , alkali content;

14942

BIS, Southern Regional Laboratory (SRL)

None

IS 1785 : Part 1 (1983)

Specification for plain hard - Drawn steel wire for prestressed concrete: Part 1 cold drawn stress - Relieved wire (Second Revision)

Rs. 27300.00 (Complete testing charges) Rs. 9300.00 (F View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5.1 (Diameter)	-
Cl 6.1 (Tensile Test On UTM)	-
Cl 6.4 (Tensile Test On UTM)	-

-
" 2mt.+2m " Excluding Except proof load, ductility, stress relaxation & reverse bend test

14943

BIS, Central Laboratory (CL)

None

IS 1293 (2019)

Plugs and socket - Outlets of rated Voltage up to and including 250 Volts and rated current up to and including 16 amperes - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 (Ratings)	-
6 (Ratings)	-
6 (Ratings)	-
7.1.1 (Accessories Classification)	-
7.1.2 (Accessories Classification)	-
7.1.3 (Accessories Classification)	-
7.1.4 (Accessories Classification)	-
7.2.1 (Socket-Outlets Classification)	-
7.2.2 (Socket-Outlets Classification)	-
7.2.3 (Socket-Outlets Classification)	-
7.2.4 (Socket-Outlets Classification)	-
7.3 (Plug Classification)	-
8.1 (MARKING)	-
8.8 (MARKING)	-
8.9 (MARKING)	-
9.1 (CHECKING OF DIMENSIONS)	-
9.2 (CHECKING OF DIMENSIONS)	-
10.1 (PROTECTION AGAINST ELECTRIC SHOCK)	-
10.1 (PROTECTION AGAINST ELECTRIC SHOCK)	-
10.4 (PROTECTION AGAINST ELECTRIC SHOCK)	-
10.5 (PROTECTION AGAINST ELECTRIC SHOCK)	-
10.6 (PROTECTION AGAINST ELECTRIC SHOCK)	-
10.7 (PROTECTION AGAINST ELECTRIC SHOCK)	-
11.1 (PROVISIONS FOR EARTHING)	-
11.2 (PROVISIONS FOR EARTHING)	-
11.3 (PROVISIONS FOR EARTHING)	-
11.4 (PROVISIONS FOR EARTHING)	-
11.5 (PROVISIONS FOR EARTHING)	-
11.6 (PROVISIONS FOR EARTHING)	-
12.1.1 (TERMINALS)	-
12.1.2 (TERMINALS)	-
12.2.1 (TERMINALS)	-
12.2.2 (TERMINALS)	-
12.2.3 (TERMINALS)	-
12.2.4 (TERMINALS)	-
12.2.5 (TERMINALS)	-
12.2.6 (TERMINALS)	-
12.2.7 (TERMINALS)	-
12.2.8 (TERMINALS)	-
12.2.9 (TERMINALS)	-
12.2.10 (TERMINALS)	-
12.2.11 (TERMINALS)	-
12.3.1 (TERMINALS)	-
12.3.2 (TERMINALS)	-
12.3.3 (TERMINALS)	-
12.3.4 (TERMINALS)	-
12.3.5 (TERMINALS)	-
12.3.6 (TERMINALS)	-
12.3.7 (TERMINALS)	-
12.3.8 (TERMINALS)	-
12.3.9 (TERMINALS)	-
12.3.10 (TERMINALS)	-
12.3.11 (TERMINALS)	-
12.3.12 (TERMINALS)	-
13.1 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.2 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.3 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.4 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.5 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.6 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.7 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.8 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.9 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.1 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.11 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.12 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.13 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.14 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.15 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.16 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.17 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.18 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.19 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.2 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.21 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.22 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.23 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
14.1 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.2 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.3 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.4 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.5 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.6 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.7 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.8 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.9 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.1 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.11 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.12 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.13 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.14 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.15 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.16 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.17 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.18 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.19 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.2 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.21 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.22 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.23 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.23.1 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.23.2 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.24 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.25 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.26 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
15 (INTERLOCKED SOCKET-OUTLETS)	-
16.1 (RESISTANCE TO AGEING,)	-
16.2 (RESISTANCE TO HARMFUL INGRESS OF WATER AND TO HUMIDITY)	-
16.3 (Resistance to Humidity)	-
17.1 (INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-
17.2 (INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-
19 (TEMPERATURE RISE)	-
20 (BREAKING CAPACITY)	-
21 (NORMAL OPERATION)	-
21 (NORMAL OPERATION)	-
21 (NORMAL OPERATION)	-
22.1 (Verification of the Maximum Withdrawal Force)	-
22.2 (Verification of Minimum Withdrawal Force)	-
23.1 (FLEXIBLE CABLES AND THEIR CONNECTION)	-
23.3 (FLEXIBLE CABLES AND THEIR CONNECTION)	-
23.4 (FLEXIBLE CABLES AND THEIR CONNECTION)	-
24.1 (MECHANICAL STRENGTH For all kinds of fixed socket-outlets )	-
24.1 (MECHANICAL STRENGTH For Plug (1) with enclosures, covers or bodies of thermoplastic or elastomeric material)	-
24.1 (MECHANICAL STRENGTH For surface mounting boxes)	-
24.2 (MECHANICAL STRENGTH For portable single socket-outlets: 1) with enclosures, covers or bodies other than thermoplastic or elastomeric material)	-
24.2 (MECHANICAL STRENGTH For portable multiple and combined socket outlets: 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-
24.2 (MECHANICAL STRENGTH For plug 1) with enclosures, covers and bodies other than elastomeric or thermoplastic material)	-
24.2 (MECHANICAL STRENGTH For plug 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-
24.3 (MECHANICAL STRENGTH for fixed socket-outlets with a main part intended to be mounted directly on a surface)	-
24.4 (MECHANICAL STRENGTH For portable single socket-outlets: 1) with enclosures, covers or bodies of thermoplastic or elastomeric material)	-
24.4 (MECHANICAL STRENGTH For portable multiple and combined socket outlets: 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-
24.4 (MECHANICAL STRENGTH For Plug 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-
24.5 (MECHANICAL STRENGTH For portable single socket-outlets: 1) with enclosures, covers or bodies of thermoplastic or elastomeric material)	-
24.5 (MECHANICAL STRENGTH For portable multiple and combined socket outlets: 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-
24.5 (MECHANICAL STRENGTH For Plug 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-
24.6 (MECHANICAL STRENGTH For screwed glands of accessories having an IP code higher than IP20)	-
24.7 (MECHANICAL STRENGTH For plug pins provided with insulating sleeves)	-
24.8 (MECHANICAL STRENGTH For shuttered socket-outlets)	-
24.9 (MECHANICAL STRENGTH For portable multiple and combined socket outlets (1) with enclosures, covers or bodies other than thermoplastic or elastomeric material)	-
24.1 (MECHANICAL STRENGTH For Plug (1) with enclosures, covers or bodies other than thermoplastic or elastomeric material)	-
24.11 (MECHANICAL STRENGTH For portable socket-outlets having means for suspension on a wall)	-
24.12 (MECHANICAL STRENGTH For portable socket-outlets having means for suspension on a wall)	-
24.13 (MECHANICAL STRENGTH For portable socket-outlets having means for suspension on a wall)	-
24.14.1 (MECHANICAL STRENGTH For fixed socket-outlets)	-
24.14.2 (MECHANICAL STRENGTH For fixed socket-outlets)	-
25.1 (RESISTANCE TO HEAT Accessories and surface mounting boxes)	-
25.2 (RESISTANCE TO HEAT Parts of insulating material necessary to retain current-carrying parts of the earthing circuit in position, as well as parts of the front surface zone of thermoplastic material)	-
25.3 (RESISTANCE TO HEAT Parts of insulating material not necessary to retain current-carrying parts and parts of the earthing circuit in position, even though they are in contact with them)	-
25.4 (RESISTANCE TO HEAT )	-
26.1 (SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-
27.1 (CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH SEALING COMPOUND)	-
27.2 (CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH SEALING COMPOUND)	-
27.3 (CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH SEALING COMPOUND)	-
28.1.1 (Resistance to Abnormal Heat and to Fire Glow-Wire Test)	-
28.1.2 (Resistance to Abnormal Heat and to Fire for plugs with pins provided with insulating sleeves)	-
28.2 (Resistance to Tracking For accessories other than IP code higher than IPX0 parts of insulating material retaining live parts in position)	-
29 (RESISTANCE TO RUSTING)	-
30.1 (ADDITIONAL TESTS ON PINS PROVIDED WITH INSULATING SLEEVES Pressure Test at High Temperature)	-
30.2 (ADDITIONAL TESTS ON PINS PROVIDED WITH INSULATING SLEEVES Static Damp Heat Test)	-
30.3 (ADDITIONAL TESTS ON PINS PROVIDED WITH INSULATING SLEEVES Tests at Low Temperature)	-
30.4 (ADDITIONAL TESTS ON PINS PROVIDED WITH INSULATING SLEEVES Impact Test at Low Temperature)	-
7.1.5 (Accessories Classification)	-
8.1 (MARKING)	-
10.1 (PROTECTION AGAINST ELECTRIC SHOCK)	-
23.2 (FLEXIBLE CABLES AND THEIR CONNECTION)	-

-
-

14944

BIS, Southern Regional Laboratory (SRL)

None

IS 398 : Part 2 (1996)

Aluminium conductors for overhead transmission purposes - Specification: Part 2 aluminium conuuctors, galvanized steel - Reinforced (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8.1.1 & 13.2 Table-1 (mech) (Diameter of Aluminium Wires Before Stranding)	-
8.1.1 & 13.2 Table 2 (mech) (Diameter of Steel Wires Before Stranding)	-
8.1.1 & 13.2 Table-1 (mech) (Diameter of Aluminium Wires After Stranding)	-
8.1.1 & 13.2 Table 2 (mech) (Diameter of Steel Wires After Stranding)	-
10 (elec) (Stranding)	-
13.3 Table 1 (mech) (Breaking Load of Aluminium Wires Before Stranding)	-
13.3 Table 2 (mech) (Breaking Load of Steel Wires Before Stranding)	-
13.3 Table 1 (mech) (Breaking Load of Aluminium Wires After Stranding)	-
13.3 Table 2 (mech) (Breaking Load of Steel Wires After Stranding)	-
13.4.1 (mech) (Ductility by Torsion Test before stranding)	-
13.4.1 (mech) (Ductility by Torsion Test after stranding)	-
13.5.1 (mech) (Wrapping Test Aluminium Wires Before Stranding)	-
13.5.1 (mech) (Wrapping Test Aluminium Wires After Stranding)	-
13.5.2 (mech) (Wrapping Test Galvanized Steel Wires Before Stranding)	-
13.5.2 (mech) (Wrapping Test Galvanized Steel Wires After Stranding)	-
13.6 (elec) (Resistance test-Aluminium wire before Stranding)	-
13.6 (elec) (Resistance test-Aluminium wire after stranding)	-
13.7.2 (chem) (Mass of Zinc coating)	-
13.7.2 (chem) (Uniformity of Zinc coating)	-
13.8 Table-4 (mech) (Lay Ratio- Aluminium Wire Outermost Layer)	-
13.8 Table-4 (mech) (Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-
13.8 Table-4 (mech) (Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-
13.8 Table-4 (mech) (Lay Ratio- Steel Core (6 Wire Layer))	-
13.4.2 (elec) (Ductility by Elongation Test before stranding)	-
13.4.2 (elec) (Ductility by Elongation Test after stranding)	-

-
" 5 m Excluding 1.)Complete upto 100 sq mm 2.)Except surface condition test, ultimate breaking load test on stranded conductor above 100 sqmm & stress strain test on conductor

14945

BIS, Eastern Regional Laboratory (ERL)

None

IS 5950 (1984)

Specification for shot firing cables (For Use Other Than In Shafts) (First Revision)

all sizes/varieties

Rs 11030/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (Conductor : Material -IS : 8130-2013)	-
4.1 (Insulation : Material -IS : 5831-1984)	-
5.1 (Sheath : materail IS : 5831-1984)	-
6.1 (Conductor : Construction IS : 8130-2013)	-
7.1 (Insulation : Application )	-
7.2 (Thickness of Insulation - average )	-
7.2 (Thickness of Insulation - Min. )	-
7.3 (Colour of Insulation)	-
8.1, 9.1 (c) (Nominal radial thickness of sheath)	-
8.2 (Thickness of Sheath)	-
8.2 (Thickness of Sheath - min.)	-
8.3 (Colour of Sheath)	-
9.1 a) (Annealing test)	-
9.1 b) (Conductor resistance test)	-
9.1 d) i) (Insulation : Tensile strength)	-
9.1 d) i) (Insulation : elongation at break)	-
9.1 d) i) (Sheath : Tensile strength)	-
9.1 d) i) (Sheath : elongation at break)	-
9.1 d) ii) (Ageing in air oven - Sheath : elongation variation at break)	-
9.1 d) iii ) (Loss of mass test - insulation )	-
9.1 d) iii ) (Loss of mass test - Sheath )	-
9.1 d) iv ) (Hot deformation - insulation )	-
9.1 d) iv ) (Hot deformation - sheath )	-
9.1 d) v ) (Heat shock - insulation )	-
9.1 d) v ) (Heat shock - Sheath )	-
9.1 d) vi ) (Shrinkage - insulation )	-
9.1 d) vi ) (Shrinkage - Sheath )	-
9.1 d) vi ) (Shrinkage : Crack observed - insulation )	-
9.1 f) (Insulation resistance test: Volume resistivity )	-
9.1 f) (Insulation resistance test : IR constant)	-
10.4 (Flammability Test )	-
10.2 (Voltage test )	-
11.1 (Manufacturer’s Identification)	-
11.2 (Cable Code)	-
12.1 (packing )	-
12.2 (Marking )	-
12.2.1 (Standard marks )	-
9.1 d) ii) (Ageing in air oven - Insulation : Tensile strength)	-
9.1 d) ii) (Ageing in air oven - Insulation : Tensile strength Variation)	-
9.1 d) ii) (Ageing in air oven - Insulation : elongation at break)	-
9.1 d) ii) (Ageing in air oven - Insulation : elongation variation at break)	-

-
Complete

14946

BIS, Northern Regional Laboratory (NRL)

None

IS 1703 (2000)

Water Fittings - Copper Alloy Float Valves (Horizontal Plunger Type) -

Rs. 4800/-and testing charges as per referred ISs View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.4 and Table 2(a) ,2(b), 3(a) & 3(b) and Fig.2 (Dimensions of Body - A)	-
7.4 and Table 2(a) ,2(b), 3(a) & 3(b) and Fig.2 (Dimensions of Body- B)	-
7.4 and Table 2(a) ,2(b), 3(a) & 3(b) and Fig.2 (Dimensions of Body - C)	-
7.4 and Table 2(a) ,2(b), 3(a) & 3(b) and Fig.2 (Dimensions of Body - D)	-
7.4 and Table 2(a) ,2(b), 3(a) & 3(b) and Fig.2 (Dimensions of Body - E)	-
7.4 and Table 2(a) ,2(b), 3(a) & 3(b) and Fig.2 (Dimensions of Body- F)	-
7.4 and Table 2(a) ,2(b), 3(a) & 3(b) and Fig.2 (Dimensions of Body- G)	-
7.4 and Table 2(a) ,2(b), 3(a) & 3(b) and Fig.2 (Dimensions of Body - H)	-
7.4 and Table 2(a) ,2(b), 3(a) & 3(b) and Fig.2 (Dimensions of Body - J)	-
7.4 and Table 2(a) ,2(b), 3(a) & 3(b) and Fig.2 (Dimensions of Body- K)	-
7.4 and Table 2(a) ,2(b), 3(a) & 3(b) and Fig.2 (Dimensions of Body - L)	-
7.4 and Table 2(a) ,2(b), 3(a) & 3(b) and Fig.2 (Dimensions of Body- M)	-
7.4 and Table 2(a) ,2(b), 3(a) & 3(b) and Fig.2 (Dimensions of Body - N)	-
7.4 and Table 2(a) ,2(b), 3(a) & 3(b) and Fig.2 (Dimensions of Body - P)	-
7.4 and Table 2(a) ,2(b), 3(a) & 3(b) and Fig.2 (Dimensions of Body- Q)	-
7.4 and Table 2(a) ,2(b), 3(a) & 3(b) and Fig.2 (Dimensions of Body- R)	-
7.6 and Table 4(a) & 4(b) (Dimensions of the piston - A)	-
7.6 and Table 4(a) & 4(b) (Dimensions of the piston - B)	-
7.6 and Table 4(a) & 4(b) (Dimensions of the piston - C)	-
7.6 and Table 4(a) & 4(b) (Dimensions of the piston - D)	-
7.6 and Table 4(a) & 4(b) (Dimensions of the piston - E)	-
7.6 and Table 4(a) & 4(b) (Dimensions of the piston - F)	-
7.6 and Table 4(a) & 4(b) (Dimensions of the piston - G)	-
7.6 and Table 4(a) & 4(b) (Dimensions of the piston - H)	-
7.6 and Table 4(a) & 4(b) (Dimensions of the piston - J)	-
7.7.1 and Table 5(a) & 5(b) (Dimensions of Levers- K)	-
7.7.1 and Table 5(a) & 5(b) (Dimensions of Levers - A)	-
7.7.1 and Table 5(a) & 5(b) (Dimensions of Levers- B)	-
7.7.1 and Table 5(a) & 5(b) (Dimensions of Levers - C)	-
7.7.1 and Table 5(a) & 5(b) (Dimensions of Levers - D)	-
7.7.1 and Table 5(a) & 5(b) (Dimensions of Levers - E)	-
7.7.1 and Table 5(a) & 5(b) (Dimensions of Levers- F)	-
7.7.1 and Table 5(a) & 5(b) (Dimensions of Levers- G)	-
7.7.1 and Table 5(a) & 5(b) (Dimensions of Levers- H)	-
7.7.1 and Table 5(a) & 5(b) (Dimensions of Levers- J)	-
7.7.1 and Table 5(a) & 5(b) (Dimensions of Levers- K)	-
7.7.1 and Table 5(a) & 5(b) (Dimensions of Levers- L)	-
7.7.1 and Table 5(a) & 5(b) (Dimensions of Levers- M)	-
7.7.1 and Table 5(a) & 5(b) (Dimensions of Levers- N)	-
7.7.3 (Clearance diameter different between the lever and the arm at the joint)	-
7.7.7 (Piston Travel)	-
7.9.2 (Silencing Pipes and Anti-Siphonage Provision -Diameter ofthe hole)	-
8.1 (Hydraulic Test)	-
3 (CLASSIFICATION)	-
4 (NOMINAL SIZES)	-
6 (MANUFACTURE AND WORKMANSHIP)	-
7.2 and Fig.1 (CONSTRUCTION)	-

-
Except shut off and mechanical strength test, Facility for chemical testing is not available

14947

BIS, Central Laboratory (CL)

None

IS 12818 (2010)

Unplasticized polyvinyl chloride (Pvc - U) screen and casing pipes for bore/tubewells - Specification (Second Revision)

Rs.6450.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
9.5 (Tensile Strength IS 12235(Part 13))	-
9.6 (Vicat Softening Temperature IS 12235 (Part 2).)	-
9.3 (Density IS 12235 (Part 14))	-
9.1 ( Visual Appearance)	-
7.2 and Table 5, 6 & 7 Fig 1B (Wall thickness, Max)	-
7.2 and Table 5, 6 & 7 Fig 1B (Wall thickness, Min)	-
7.1, 7.2 and Table 5, 6 & 7 Fig 1B (Mean outside dia over connection,mm (Take 4 reading and maximum valu reported))	-
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B (Wall thickness)	-

-
Excluding Test facility not avaialble for Cl 9.4 Resistance to External Blows ,9.7 Effect on Water;

14948

BIS, Central Laboratory (CL)

None

IS 2029 (1998)

Ring wrenches (Spanners) - Specification (Fourth Revision)

Rs.3700/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.4 (CARBON)	-
Cl.4 (SULPHUR)	-
Cl.4 (PHOSPHURS)	-
Cl.4 (MANGANESE)	-
Cl.4 (NITROGEN)	-
Cl.4 (SILICON)	-
Cl.4 (ALUMINIUM)	-
Cl.4 (CHROMIUM)	-
Cl.4 (NICKEL)	-
Cl.4 (VANADIUM)	-
Cl.4 (MOLYBDENUM)	-
3, Table-1 (Dimensions- s1)	-
3, Table-1 (Dimensions- s2)	-
3, Table-1 (Dimensions- a)	-
3, Table-1 (Dimensions- b1)	-
3, Table-1 (Dimensions- b2)	-
3, Table-1 (Dimensions- L)	-
5 (Hardness)	-
6 (Workmanship and Finish)	-
6 (Torque Testing)	-
7 (Designation)	-

-
Grade designation of material as per relevant IS may please declared.; Excluding -; torque test

14949

BIS, Southern Regional Laboratory (SRL)

None

IS 11947 (1987)

Specification for soft magnetic iron rods, bars, flats and sections

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5 (PHYSICAL CONDITIONS)	-
6.1 (Tensile Strength-1608: Part 1)	-
6.2 (Hardness - 1586)	-
8.2 (Tolerances for Round Rods and Bars)	-
8.3 (Tolerances on Thickness for Rectangular Flat)	-
8.4 (Tolerances on Width for Rectangular F)	-
8.6 (Tolerance on Length-for-Rods, Bars, Flats and Section)	-
8.7 (Tolerance on Straightness of Bars)	-
8.8 (Tolerance on Out-of-Roundness)	-

-
" mech - 2 x 500 mm Excluding except bend test and chemical tests

14950

BIS, Southern Regional Laboratory (SRL)

None

IS 12146 (1987)

Specification for carbon manganese steel forgings for pressure vessels

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8 (Freedom from defects)	-
6.1, Table 3 (Tensile Test-1608:Part 1)	-
6.1, Table 3 (Yield Strength, Mpa)	-
6.1, Table 3 (Elongation, %)	-
6.1, Table 3 (Reduction in area, Percent)	-
6.1, Table 3 (Impact Test)	-

-
" mech - 100 gm drillings " Excluding except ultrasonic test and Chemical tests

14951

BIS, Southern Regional Laboratory (SRL)

None

IS 14542 (1998)

Partly skimmed milk powder specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 6.6.1 (Bacterial Count (IS 5402))	-
Cl 6.6.2 (Coliform Count ((IS 5402))	-
Table 1(iii) (Milk fat, Type I (IS I1722))	-
Table 1(iii) (Milk fat, Type II (IS I1722))	-
Table 1(iv) (Insolubility index, a) Roller dried Type I (IS 12759))	-
Table 1(iv) (Insolubility index, a) Roller dried Type II (IS 12759))	-
Table 1(iv) (Insolubility index, b) Spray dried Type I (IS 12759))	-
Table 1(iv) (Insolubility index, b) Spray dried Type II (IS 12759))	-
Table 1(v) (Total ash Type I (Annex B of IS 14433 - Part 1))	-
Table 1(v) (Total ash Type II (Annex B of IS 14433 - Part 1))	-
Table 1(vi) (Titratable acidity (as lactic acid) Type I (IS 11766))	-
Table 1(vi) (Titratable acidity (as lactic acid) Type II (IS 11766))	-
Cl 6.4 (Flavour and Taste (IS 10030))	-

-
" 2 x 500 g "

14952

BIS, Southern Regional Laboratory (SRL)

None

IS 4505 (2015)

Sodium formaldehyde sulphoxylate - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl no 4.1 (Description )	-
Cl no 4.2 (Description )	-
Cl no 4.3 [ Table 1, Sl no.(i) ] Annex A-2 Grade-1 (Sodium formaldehyde sulphoxylate dihydrate (NaHSO2.CH2O.2H2O))	-

-
" 500 g x 2 1 pack for keeping quality test as per clause 5 "

14953

BIS, Northern Regional Laboratory (NRL)

None

IS 398 : Part 4 (1994)

Aluminium conductors for overhead transmission purposes: Part 4 aluminium alloy stranded conductors (Aluminium - Magnesium - Silicon Type) - Specification (Third Revision)

Please see remarks View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 (Freedom from Defects)	-
7.1 Table-1 (Dimensional measurement of wires)	-
7.2.2 Table-2, Table-4 (Calculated resistance of Stranded Conductor)	-
8.1 (Joints in wires-Conductors Containing Seven Wires)	-
8.2 (Joints in wires-Conductors Containing More Than Seven Wires)	-
9.1 (Stranding)	-
9.2 Table 3 (Lay Ratio of stranded conductors)	-
9.3 (Direction of Lay)	-
9.4 (Multiple layers of wires)	-
11 (Packing and Marking)	-
12.2 Table 1 (Breaking Load Test- Before Stranding)	-
12.2 Table 1 (Breaking Load Test- After Stranding)	-
12.3 Table 1 (Elongation Test- Before Stranding)	-
12.3 Table 1 (Elongation Test- After Stranding)	-
12.4 Table 1 (Resistance of Aluminium wire)	-

-
Test facility is complete

14954

BIS, Northern Regional Laboratory (NRL)

None

IS 1673 (1984)

Spectfication for mild steel wire, cold heading quality (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1 (i)Ultimate Tensile Strength,)	-
7.2 (ii) Reverse Torsion Test)	-
8 ( DIMENSIONS AND TOLERANCES)	-
6 (FREEDOM FROM DEFECTS)	-
Cl. 5.1 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.1 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.1 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.1 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.1 (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-

-
-

14955

BIS, Southern Regional Laboratory (SRL)

None

IS 336 (1973)

Specification for ether

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl no .3.1 (Description)	-
Cl no .3.2 (Odour and Taste )	-
Cl No. 3.2.1 (Ether , anaesthetic)	-
Cl no .3.3.1 (Composition )	-
Cl no .3.3.2 (Composition )	-
Cl no .3.4 (Solubility )	-
Cl no .3.5 [ Table 1, Sl no.(ii) ] Appendix A 3 (Peroxides )	-
Cl no .3.5 [ Table 1, Sl no.(iv) ] Appendix A 5 (Residue on Evaporation )	-
Cl no .3.5 [ Table 1, Sl no.(v) ] Appendix A 6 (Methyl alcohol )	-
Cl no .3.5 [ Table 1, Sl no.(vi) ] Appendix A 7 (Aldehydes and acetone )	-
Cl no .3.5 [ Table 1, Sl no.(vii) ] Appendix A 8 (Sulphurous acids and other free acids )	-

-
" 500 ml x 2 Excluding except distillation range, relative density

14956

BIS, Eastern Regional Laboratory (ERL)

None

IS 14255 (1995)

Aertal bunched cables - For working voltages up to and including 1100 Volts - Specification

complete for Cat 01(Except melt flow, vicat, bending)

- View breakup
Total Rs. 48x300 + 250x9 i.e. Rs.16650.00 for XLPE insulated single core cable Rs. 43x300 + 250x9 i.e. Rs.15150.00 for PE insulated single core cable

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (Insulation)	-
6.1 (Flexibility class)	-
6.2 (Compactness)	-
6.2 (No of strands)	-
6.2 (Surface)	-
6.3 (Protective barrier)	-
6.4 (size of street lighting conductor)	-
6.5 (Size of messenger conductor )	-
6.6 (Joints in messenger conductor )	-
6.6 (Direction of outer layer)	-
7.2 ( Thickness of insulation)	-
7.3 (Tolerance on thickness of insulation )	-
7.4 (Aplication of the insulation )	-
7.5 (Colour of the insulation )	-
8.1 (Core identification)	-
8.2 (Core identification)	-
8.3 (Identification by other means)	-
9.1 (Assembly (Laying up))	-
9.2 (Assembly (Laying up))	-
9.3 (Direction of lay)	-
10.1 a) i) (Tests on phase/street light conductor: tensile test - Test method IS10810:Part 2)	-
10.1 a) ii) (Wrapping test - 10810: Part 3)	-
10.1 a) iii) (Resistance test - IS10810: Part 5)	-
10.1 b) i) (Test on messenger conductor: Breaking load - IS 10810: Part 2)	-
10.1 b) ii) (Test on messenger conductor: Elongation test - Cl 11.3)	-
10.1 b) iii) (Test on messenger conductor: Resistance test - IS 10810: Part 5)	-
10.1 c) i) (Physical tests for XLPE Insulation: Tensile strength - IS 10810: Part 7)	-
10.1 c) i) (Physical tests for XLPE Insulation: elongation at break - IS 10810: part 7)	-
10.1 c) ii) (Ageing in air oven : Tensile strength variation - IS 10810:Part 11)	-
10.1 c) ii) (Ageing in air oven : Elongation variation- IS 10810: Part 11)	-
10.1 c) iii) (Hot set test: Elongation under load - IS 10810: Part 30)	-
10.1 c) iii) (Hot set test: Permanent elongation (set) after cooling - IS 10810: Part 30)	-
10.1 c) iv) (Shrinkage test : Shrinkage - 10810:Part 12)	-
10.1 c) iv) (Shrinkage test : Crack Observed - 10810:Part 12)	-
10.1 c) v) (Water ahsorption (Gravimetric) - IS 10810: Part 33 )	-
10.1 d) i) (Physical test for PE insulation: Tensile strength - IS 10810: Part 7 )	-
10.1 d) i) (Physical test for PE insulation: elongation at break - IS 10810: Part 7)	-
10.1 f) (Insulation resistance (Volume resistivity) test a) volume resistivity at 27°C - IS 10810: Part 43)	-
10.1 f) (Insulation resistance (Volume resistivity) test b) volume resistivity at 70°C - IS 10810: Part 43)	-
10.1 g) (High voltage test - IS10810:Part 45)	-

-
Facility not available for breaking load of messenger conductor, Carbon Black test, Vicat Test, Environmental stress cracking for PE insulation. For XLPE water absorption test facility available upto 25 sq.mm. (Facility for nominal area of conductor, Tensile & Elongation above 2.0 mm thickness is not available). 5 mtr Aluminium wire before stranding to be provided additionally.

14957

BIS, Southern Regional Laboratory (SRL)

None

IS 1161 (2014)

Steel tubes for structural purposes - Specification (Fifth Revision)

5725 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 6 (Outer Diameter, Thickness & Mass)	-
Cl 7 (Workmanship)	-
Cl 11 (Tensile Test, Flattening Test & Cold Bend Test)	-
5 AND AS PER IS 10748 (COPPER)	-
5 AND AS PER IS 10748 (MICRO ALLOY)	-
5 AND AS PER IS 10748 (CARBON EQUIVALENT)	-
5 AND AS PER IS 10748 (CARBON)	-
Clause - 5.1, Table-3 ( ALUMINIUM)	-
Clause - 5.1, Table-3 (SILICON)	-
Clause - 5.1, Table-3 (NITROGEN)	-
Clause - 5.1, Table-3 (MANGANESE)	-
Clause - 5.1, Table-3 (PHOSPHURS)	-
Clause - 5.1, Table-3 (SULPHUR)	-

-
" mech - 1.5 m Chemical Facility is available Quantity: 5 Pieces of 5cm X 5cm Excluding except cold bend test

14958

BIS, Northern Regional Laboratory (NRL)

None

IS 1610 (2018)

Household sewing machines - General requirements (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (Driving arrangement Hand Operated Sewing Machine)	-
4.1 (Sewing Mechanism Design )	-
4.2 (Sewing Mechanism Reverse stitch mechanism )	-
4.2.1 (Sewing Mechanism Stitch Regulator)	-
4.3 (Sewing Mechanism Thread Tension)	-
4.4 (Sewing Mechanism Timing)	-
4.7 (Sewing Mechanism Thread Spool Pin)	-
6 (Lubrication)	-
8 (WORKMANSHIP AND FINISH)	-
8 (WORKMANSHIP AND FINISH)	-
8 (WORKMANSHIP AND FINISH)	-
10.1 IS 7491 (Accuracy Requirement Functional Dimension Feed Dog Measuring Condition - Feed dog raised to its highest position )	-
10.1 IS 7491 (Accuracy Requirement Functional Dimension Shuttle and shuttle driver Measuring Condition - Shuttle heel at bottom - most position)	-
10.1 IS 7491 (Accuracy Requirement Functional Dimension Presser foot Measuring Condition - Presser foot in lifted condition)	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Needle bar Measuring Condition - Needle bar at lower-most condition)	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Needle bar Measuring Condition - Needle bar at lower-most condition)	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Thread take up lever Measuring Condition - Thread take up lever at top and intermediate position)	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Thread take up lever Measuring Condition - Thread take up lever at top and intermediate position)	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Shuttle Measuring Condition - Difference between highest & lowest position of needle bar.)	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Shuttle Measuring Condition - Tip of pin at top most bottom most position of needle bar)	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Shuttle Measuring Condition - Difference between highest & lowest position of needle bar.)	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Arm shaft Measuring Condition -At different fly wheel position (turn fly wheel by hand) axial push./pull to be given)	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Flywheel Measuring Condition - Rotate flywheel to Radially measure eccentrity)	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Feed section Measuring Condition - At its highest position above needle place)	-
10.2 IS 7492 (Sewing Requirement)	-
10.2 IS 7492 (Sewing Requirement)	-
10.2 IS 7492 (Sewing Requirement)	-
10.2 IS 7492 (Sewing Requirement)	-
10.2 IS 7492 (Sewing Requirement)	-
10.3 IS 7493 (Durability Requirement Needle bar Measuring Condition - Needle bar at lower-most condition)	-
10.1 IS 7491 (Accuracy Requirement Functional Dimension Shuttle and shuttle driver Measuring Condition - Shuttle heel at bottom - most position)	-
10.3 IS 7493 (Durability Requirement Thread take up lever Measuring Condition - Thread take up lever at top and intermediate position)	-
10.3 IS 7493 (Durability Requirement Thread take up lever Measuring Condition - Thread take up lever at top and intermediate position)	-
10.3 IS 7493 (Durability Requirement Shuttle Measuring Condition - Tip of pin at top most bottom most position of needle bar)	-
10.3 IS 7493 (Accuracy Requirement Assembly Clearance Shuttle Measuring Condition - Difference between two indicator readings when needle bar is at its highest and lowest position)	-
10.3 IS 7493 (Durability requirement Arm shaft Measuring Condition -At different fly wheel position (turn fly wheel by hand) axial push./pull to be given)	-
10.3 IS 7493 (Durability Requirement Feed section Measuring Condition - At its highest position above needle place)	-
12 (Marking)	-
12 (Marking)	-
Clause 8.3 (Plating)	-

-
Mechanical- Complete, Chemical- Not Available

14959

BIS, Northern Regional Laboratory (NRL)

None

IS 1341 (2018)

Steel Butt Hinges - Specification (Sixth Revision)

3550/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 Tables 2 to 9 (3) (Length A)	-
5.1 Tables 2 to 9 (4) (Breadth B)	-
5.1 Tables 2 to 9 (4) (Breadth B1)	-
5.1 Tables 2 to 9 (4) (Breadth B2)	-
5.1 Tables 2 to 9 (5) (Thickness of Flap C)	-
5.1 Tables 2 to 9 (6) (Diameter of Hinge Pin D)	-
6.4.2 (X)	-
6.4.2 (Y)	-
6.4.2 (Z)	-
3 Tables 2 to 9 (Types)	-
5.1 Tables 2 to 9 (2) (Size of Hinge)	-
5.1 Tables 2 to 9 (7) (Number of Knuckles)	-
5.1 Tables 2 to 9 (8) (Number of Screw Holes)	-
5.1 Tables 2 to 9 (9) (Holes for Screw No.)	-
6.1 (General)	-
6.2.1 (Knuckles)	-
6.3 (Pins)	-
6.4 (Screw Holes)	-
6.4.2 (Position of Holes)	-
TABLE-1 (Clause-4) ( CARBON)	-
TABLE-1 (Clause-4) (SULPHUR)	-
TABLE-1 (Clause-4) (MANGANESE)	-
TABLE-1 (Clause-4) (PHOSPHURS)	-
Cl 4 & Table 1 (Silicon- IS 228(Part 2))	-
Clause 4 Table 1 (Nitrogen ( Flap))	-
TABLE-1 (Clause-4) (TITANIUM)	-
TABLE-1 (Clause-4) (VANADIUM)	-
TABLE-1 (Clause-4) (NIOBIUM)	-
TABLE-1 (Clause-4) (Molybdenum)	-
TABLE-1 (Clause-4) (Chromium)	-
TABLE-1 (Clause-4) (Nickel)	-
TABLE-1 (Clause-4) ( ALUMINIUM)	-
Clause 4 Table 1 (Manganese ( Pin))	-
Clause 4 Table 1 (Phosphorus ( Pin))	-
Clause 4 Table 1 (Sulphur ( Pin))	-
Clause 4 Table 1 (Carbon ( Pin))	-
Clause 4 Table 1 (Nitrogen ( Flap))	-
Clause 4 Table 1 (Manganese ( Flap))	-
Clause 4 Table 1 (Phosphorus ( Flap))	-
Clause 4 Table 1 (Sulphur ( Flap))	-
Clause 4 Table 1 (Carbon ( Flap))	-

-
Test facility is complete for mechanical Except Microalloying Elements

14960

BIS, Northern Regional Laboratory (NRL)

None

IS 398 : Part 1 (1996)

Aluminium conductors for overhead transmission purposes - Specification: Part 1 aluminium stranded conductors (Third Revision)

Rs.1600/- for 7 strands, Rs.3750/- for 19 strands View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
12.2, Table-1 (Measurement of diameter of individual aluminium wire)	-
12.3, Table-1 (Breaking load before stranding)	-
12.3, Table-1 (Breaking load after stranding)	-
12.4 (Wrapping test)	-
12.5, Table 1 (Resistance test)	-
12.6, Table 3 (Measurement of lay ratio)	-
9.3 (Stranding)	-
6 (Freedom from defects)	-

-
Test facility is complete

14961

BIS, Northern Regional Laboratory (NRL)

None

IS 1328 (1996)

Veneered Decorative Plywood -Specification

Please see remarks View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1.1 (Requirements - Open splits, checks or open joints - For Type 1 - Cl. 7.1.1)	-
7.2.1 (Requirements - Open splits, checks or open joints - For Type 2 - Cl. 7.2.1)	-
7.2.2 (Requirements - Other defects - For Type 2 - Cl. 7.2.2.)	-
8 (Dimensions & Tolerances - Length - Cl. 8)	-
8 (Dimensions & Tolerances - Width - Cl. 8)	-
8 (Dimensions & Tolerances - Thickness - Cl. 8)	-
8 (Dimensions & Tolerances - Edge Straightness - Annexure C)	-
8 (Dimensions & Tolerances - Squareness - Annexure C)	-
11 (Tests - Moisture Content - Part 1 of IS 1734)	-
11 (Tests - Water Resistance Test - Cl. 11.1.2.1 [for MR Grade])	-
11 (Tests - Water Resistance Test - Cl. 11.1.2.2 [for BWR Grade])	-
4.1 (Grade - For BWR)	-
4.1 (Grade - For MR)	-
4.2 (Type - For Type 1)	-
4.2 (Type - For Type 2)	-
7.1.2 (Requirements - Other defects - For Type 1 - Cl. 7.1.2)	-
7.2.3 (Requirements - Other Charcteristics and Manufacturing Defects - For Type 2 - Cl. 7.2.3)	-
9 (Finish - Cl. 9.1, 8.3)	-
9 (Finish - Cl. 9.2, 8.3)	-

-
Test facility is complete

14962

BIS, Northern Regional Laboratory (NRL)

None

IS 13095 (1991)

Butterfly valves for general purposes

Rs3300/-t View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (VALVE END CONNECTIONS)	-
5 (SERVICE APPLICATIONS)	-
6 ( NOMINAL SIZES )	-
7 (NOMINAL PRESSURES)	-
7.2 (Class designations)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Flange-D)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges-IS 6418 (Table 2/3/6/7/10)- Flange-b)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges-IS 6418 (Table 2/3/6/7/10)- Rasied Face-d4)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges-IS 6418 (Table 2/3/6/7/10)- Rasied Face-f)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Bolting )	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Drilling -Nos. )	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Drilling -d2)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Drilling -k)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Neck -d3)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Neck- r)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Flange-D)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Flange-b)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Rasied Face-d4)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Raised Face - f)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Bolting)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Drilling -Nos. )	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Drilling -d2 )	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Drilling -k)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Neck -d3)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Neck-r)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Pipe O.D.- d1)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Flange - D)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Flange - b)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Raised Face - d4)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Raised Face - f)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Drilling - Nos.)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Drilling -d2)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Drilling -k)	-
9.1.1 ( Double Flanged Body Ends)	-
9.2.2 (Wafer Body Ends)	-
10.1 -Table1 (FACE TO FACE DIMENSIONS)	-
11 (Bodies)	-
12 (DISC AND SHAFT)	-
13 (SEATING AND LININGS)	-
14.2 (BEARINGS)	-
14.3 (BEARINGS)	-
16 (OPERATION)	-
17.1 (Performance Testing)	-
17.2 (Body Test)	-
17.3 (Seat Test)	-
17.4 (Disc Strength Test)	-

-
Except Microalloying Elements

14963

BIS, Central Laboratory (CL)

None

IS 8944 (2005)

Chlorpyrifos, emulsifiable concentrates - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2.1 (Description)	-
3.2.2 (Cold Test)	-
3.2.3 (Flash Point (Abel))	-
3.2.4 (Emulsion Stability)	-
3.3.1 (Chloropyrifos content)	-
3.3.2 (Acidity (as H2SO4), )	-

-
Excluding Cl. 3.3.1 Content;

14964

BIS, Southern Regional Laboratory (SRL)

None

IS 10109 (2018)

Oil pressure stoves - Offset burner type - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
9.6 (Resistance to Draught)	-
9.7 (Fuel Creep)	-
9.1.1 (Air Pressure Test)	-
9.1.2 ( Safety Pressure Test)	-
9.1.3 (Bursting Pressure Test)	-
5.4 (Plastic components (for example, handles) shall be free from fissures, distortions, blemishes and discolouration.)	-
6.2 (The vassel when kept on the stove shall not touch burner top.)	-
6.4 (Minimum Sheet thickness of fuel container)	-
6.5 (Maximum height of the fuel feed pipe into the container from the bottom)	-
7.1.1 (Construction, General)	-
7.1.1 (Construction, General)	-
7.1.1 (Construction, General The base of the fuel container clear from the ground )	-
7.1.1 (Construction, General The fuel container may be of detachable type)	-
7.1.3 (Regulator near the socket may be provided for opening or closing of the fuel supply.In case the Regulator is not provided,the kerosene oil should not come out of the nipple when the tank is full under atmospheric pressure.)	-
7.3 (Pump)	-
7.4 ( Pressure Release Screw)	-
7.7 (Taps)	-
7.1 (Pricker)	-

-
" 1 set " Excluding Except Burner assembly, Washer, Workmanship, Fuel Consumption & Thermal efficiency ,

14965

BIS, Southern Regional Laboratory (SRL)

None

IS 3205 (1984)

Specification for precipitated barium carbonate, technical (First Revision)

Rs 1575/- Grade 1; Rs 1125/- for Gr 2 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (Description)	-
3.2, Table 1 and Appendix A-2 of IS 3205 (Barium (as Ba ) - for All Grades)	-
3.2, Table 1 and Appendix A-4 of IS 3205 (Moisture - For Grade 1 )	-
3.2, Table 1 and Appendix A-4 of IS 3205 (Moisture - For Grade 2)	-
3.2, Table 1 and Appendix A-5 of IS 3205 (Matter insolubile in hydrochloric acid - For Grade 1)	-
3.2, Table 1 and Appendix A-5 of IS 3205 (Matter insolubile in hydrochloric acid - For Grade 2)	-
3.2, Table 1 and Appendix A-6 of IS 3205 (Free Alkali - For Grade 2)	-
3.2, Table 1 and Appendix A-7 of IS 3205 (Water Soluble Sulphide ( as BaS ) -For Grade 1)	-
3.2, Table 1 and Appendix A-7 of IS 3205 (Water Soluble Sulphide ( as BaS ) -For Grade 2)	-
3.2, Table 1 and Appendix A-8 of IS 3205 (Total Sulphur ( as SO4 ) - For Grade 1)	-
3.2, Table 1 and Appendix A-9 of IS 3205 (Alkali and other metasulphates ( as BaSO4 ) - For Grade 1 )	-
3.2, Table 1 and Appendix A-9 of IS 3205 (Alkali and other metasulphates ( as BaSO4 ) - For Grade 2)	-
3.2, Table 1 and Appendix A-10 of IS 3205 (Sodium Oxides ( as NaO2 ) - For Grade 1)	-
3.2, Table 1 and Appendix A-11 of IS 3205 (Iron ( as Fe2O3) - For Grade 1)	-
3.2, Table 1 and Appendix A-11 of IS 3205 (Iron ( as Fe2O3) - For Grade 2)	-
3.2, Table 1 and Appendix A-14 of IS 3205 (Reaction efficiency ( after 45 minutes ) - For Grade 2)	-

-
" 500 g " Excluding except carbonates for all grades, residue retained on 63 microns IS sieve for grade 1

14966

BIS, Central Laboratory (CL)

None

IS 9798 (2013)

Low pressure regulators for use with liquefied petroleum gas (LPG) - Specification (Second Revision)

14276 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2 IS 742 (Material)	-
4.1.1 IS 2305 (Material)	-
4.2.1a (Finish)	-
4.2.1b IS 9844 IS 6009 (Finish)	-
4.3.1 (Diaphragm Material)	-
4.3.2 IS 3400(Part 4) (The material shall not show change of more than 10 IRHD when subjected to ageing of 72 h at 70°C in accordance with the method prescribed in 3 or 4 of IS 3400 (Part 4))	-
4.3.3 (Clamping test)	-
4.3.4 Annex C (Bursting & Pull out test)	-
4.3.5ai Annex D (The material shall, after immersion in n-pentane or octet commercial LPG for 72 h, meet the appropriate requirements specified in Annex D Diaphragm: Extractable )	-
4.3.5b IS 3400(Part 2) (Changes in hardness, before and after the immersion )	-
4.3.7 Annex E (The material shall have 25 percent max compression set when subjected to compression set test in accordance with the method prescribed in Annex E.)	-
4.4.1 (Valve Pad Material)	-
4.4.2ai Annex D (The material shall, after immersion in n-pentane or octet commercial LPG for 72 h, meet the appropriate requirements specified in Annex D Extractable )	-
4.4.2aii Annex D ( Absorbed)	-
4.4.2b IS 3400(Part 2) (Changes in hardness, before and after the test)	-
4.4.3 IS 3400(Part 4) (The material shall not show change of more than 10 IRHD when subjected to ageing of 72 h at 70°C in accordance with the method prescribed in 3 or 4 of IS 3400 (Part 4))	-
4.4.4 (Valve Pad Material)	-
4.4.5 Annex E (The material shall have 40 percent max compression set when subjected to compression set test in accordance with the method prescribed in Annex E.)	-
4.5,4.4.1 (Seals O rings and rubber components other than diaphragm and valve pad )	-
4.5,4.4.2i Annex D (The material shall, after immersion in n-pentane or octet commercial LPG for 72 h, meet the appropriate requirements specified in Annex D Extractable )	-
4.5,4.4.2ii Annex D ( Absorbed)	-
4.5,4.4.2b IS 3400(Part 2) (Changes in hardness, before and after the test)	-
4.5,4.4.3 IS 3400(Part 4) (The material shall not show change of more than 10 IRHD when subjected to ageing of 72 h at 70°C in accordance with the method prescribed in 3 or 4 of IS 3400 (Part 4))	-
4.5,4.4.5 Annex E (The material shall have 40 percent max compression set when subjected to compression set test in accordance with the method prescribed in Annex E.)	-
4.5,4.4.1 (Seals O rings and rubber components other than diaphragm and valve pad )	-
4.5,4.4.2i Annex D (The material shall, after immersion in n-pentane or octet commercial LPG for 72 h, meet the appropriate requirements specified in Annex D Extractable )	-
4.5,4.4.2ii Annex D ( Absorbed)	-
4.5,4.4.2b IS 3400(Part 2) (Changes in hardness, before and after the test)	-
4.5,4.4.3 IS 3400(Part 4) (The material shall not show change of more than 10 IRHD when subjected to ageing of 72 h at 70°C in accordance with the method prescribed in 3 or 4 of IS 3400 (Part 4))	-
4.5,4.4.5 Annex E (The material shall have 40 percent max compression set when subjected to compression set test in accordance with the method prescribed in Annex E.)	-
4.5,4.4.1 (Seals O rings and rubber components other than diaphragm and valve pad )	-
4.5,4.4.2i Annex D (The material shall, after immersion in n-pentane or octet commercial LPG for 72 h, meet the appropriate requirements specified in Annex D Extractable )	-
4.5,4.4.2ii Annex D ( Absorbed)	-
4.5,4.4.2b IS 3400(Part 2) (Changes in hardness, before and after the test)	-
4.5,4.4.3 IS 3400(Part 4) (The material shall not show change of more than 10 IRHD when subjected to ageing of 72 h at 70°C in accordance with the method prescribed in 3 or 4 of IS 3400 (Part 4))	-
4.5,4.4.5 Annex E (The material shall have 40 percent max compression set when subjected to compression set test in accordance with the method prescribed in Annex E.)	-
5.2 (Construction and Workmanship)	-
5.5 (Inlet Connection)	-
5.5 (Inlet Connection)	-
5.5 (Inlet Connection)	-
5.6,5.6.1 (Outlet Connection:- Non-threaded Outlet Connection)	-
5.7 (Body)	-
5.8 (Vent)	-
5.10.1 (Valve Pad Fitting)	-
5.11.1,8.11 Table 1 (The fixing of the inlet connection on to the regulator body , whether it is of the threaded or non - threaded type or in one piece, shall withstand the following tests, under the conditions defined in 8.11 (see Table 1))	-
5.11.1,8.11 Table 1 (The fixing of the inlet connection on to the regulator body , whether it is of the threaded or non - threaded type or in one piece, shall withstand the following tests, under the conditions defined in 8.11 (see Table 1))	-
5.12.1,8.11 Table 3 (The regulators when installed as indicated in the installation instruction shall resist the following tests under the conditions defined in 8.11 (see Table 3 ))	-
5.11.2a,8.11 Table 2 (The fixing of the outlet connection on to the regulator body, whether it is of the threaded, or non-threaded type or in one piece, shall resist the following tests, under the conditions defined in 8.11 (see Table 2):a)For non - threaded hose connection)	-
5.11.2b,8.11 Table 2 (The fixing of the outlet connection on to the regulator body, whether it is of the threaded, or non-threaded type or in one piece, shall resist the following tests, under the conditions defined in 8.11 (see Table 2):b)For threaded unions)	-
6,6.1,6.2 (SOUNDNESS)	-
6,6.1,6.2 (SOUNDNESS)	-
6.3 (SOUNDNESS)	-
6.4 (SOUNDNESS)	-
8.2 (CHATTER)	-
8.9 (Performance (Before Cycle test, Low Temp. Test and High Temp. Test) Inlet Pressure Flow Rate )	-
8.9 (0.5 kgf/cm2 100 % )	-
8.9 (17 kgf/cm2 10 % )	-
8.9 (Static(lock up) pressure)	-
8.9 (Performance (Before Cycle test, Low Temp. Test and High Temp. Test) Inlet Pressure Flow Rate )	-
8.10.1 Annex G (Cycle Test)	-
6,6.1,6.2 (SOUNDNESS (After Cycle Test))	-
8.9 (Performance (After Cycle test) Inlet Pressure Flow Rate )	-
8.10.2 Annex H 8.9 (Low Temperature Test Performance test after exposure to temperature at -200 C for 10 Min and back to ambient condition. Inlet Pressure Flow Rate)	-
8.9 (Static(lock up) pressure)	-
8.10.3 Annex H 8.9 (High Temperature Test Performance test after exposure to temperature at 650 C for 10 Min and back to ambient condition. Inlet Pressure Flow Rate)	-
8.9 (0.5 kgf/cm2 100 % )	-
8.9 (17 kgf/cm2 10 % )	-
8.9 (Static(lock up) pressure)	-
4.4.5 Annex E (The material shall have 40 percent max compression set when subjected to compression set test in accordance with the method prescribed in Annex E.)	-
Cl. 4.2 (Aluminium)	-
Cl. 4.2 (Copper)	-
Cl. 4.2 (Magnesium)	-
Cl. 4.2 (Iron)	-
Cl. 4.2 (Lead)	-
Cl. 4.2 (Cadmium)	-
Cl. 4.2 (Tin)	-
Cl. 4.2 (Thalium+ Indium)	-
Cl. 4.2 (Nickel)	-
Cl. 4.2 (Zinc)	-
Cl. 4.2 (Chromium)	-

-
-

14967

BIS, Southern Regional Laboratory (SRL)

None

IS 11587 (1986)

Specification for structural weather resistant steels

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 4 (Grades)	-
Cl 8 (Tensile Test)	-
Cl 10 (Impact Test)	-
Cl 11 (Flattening Test)	-
Cl 12 (Freedom from Defects)	-
Cl 13 (Dimensions)	-
Cl 16 (Mass)	-
Cl 13 (Dimensions)	-
Cl 16 (Mass)	-

-
" 1 m Excluding except chemical tests (Prepared test pieces are required for Impact test)

14968

BIS, Central Laboratory (CL)

None

IS 1554 : Part 1 (1988)

Specification for pvc insulated (Heavy Duty) electric cables: Part 1 for working voltages up to and including 1100 v (Third Revision)

Rs 26700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (MATERIALS : CONDUCTOR)	-
4.1.1 (INSULATION : General Purjose Insulaiion)	-
4.1.2 (INSULATION : Heat Resisting Insulation)	-
5.1 (MATERIALS : FILLER AND INNER SHEATH)	-
6.1 (MATERIALS : ARMGURING)	-
7.1.1 (OUTER SHEATH : For Cables with General Purpose InsuIafion)	-
7.1.2 (OUTER SHEATH : For Cables with Heat Resisting InsuIalion)	-
8.1 (CONSTRUCTION : CONDUCTOR)	-
8.2 (CONSTRUCTION : CONDUCTOR)	-
9.2 (INSULATION : Thickness of Insulation)	-
9.4 (INSULATION : Application of Insulation)	-
10.1 (CORE IDENTIFICATION)	-
10.2 (CORE IDENTIFICATION)	-
10.3 (CORE IDENTIFICATION)	-
10.3.1 (Arrangement of Marking)	-
11.1 (LAYING UP OF CORES)	-
12.1 (INNER SHEATH)	-
12.2 (INNER SHEATH)	-
12.3 (INNER SHEATH :Thickness of Inner Sheath)	-
13.1.1 (ARMOURING : Application)	-
13.1.2 (Armouring: Coverage )	-
13.1.3 (ARMOURING : Direction of lay )	-
13.2 (ARMOURING : Type of Armour)	-
13.3 (Armouring : Dimensions -Wire Diameter)	-
13.3 (Armouring : Dimensions -Formed wire )	-
13.4 (ARMOURING : Joints)	-
13.5.1 (ARMOURING : Resistance)	-
13.5.2 (ARMOURING : Resistance)	-
13.6 a) (ARMOURING: Tensile Strength)	-
13.6 b) (ARMOURING: Elongation )	-
13.6 f) (ARMOURING: Mass of zinc coating )	-
13.6 g) (ARMOURING: Resistivity)	-
14.1 (OUTER SHEATH)	-
14.3 (OUTER SHEATH : Colour )	-
14.4.1 (Thickness of Outer Sheath : Unarmowed Cables)	-
14.4.2 (Thickness of Outer Sheath : Armoured Cables)	-
15.1 a) 1) (Tests on conductor : Annealing test ( for copper ))	-
15.1 a) 2) (Tensile test (for aluminium) - Before stranding )	-
15.1 a) 2) (Tensile test (for aluminium) - After stranding )	-
15.1 a) 3) (Tests on conductor : Wrapping test ( for aluminium ))	-
15.1 a) 4) (Tests on conductor : Conductor resistance test)	-
15.1 a) 4) (Resistance test - Neutral conductor )	-
15.1 d)1) (Phyaical tests for insulation : Tensile Test)	-
15.1 d)1) (Phyaical tests for insulation : Elongation )	-
15.1 d)1) (Physical tests for sheath : Tensile stregth )	-
15.1 d)1) (Physical tests for sheath : Elongation )	-
15.1 d)2) (Phyaical tests for insulation- Ageing in air Oven : Tensile Test)	-
15.1 d)2) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-
15.1 d)2) (Phyaical tests for insulation - Ageing in air oven : Elongation )	-
15.1 d)2) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-
15.1 d)2) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-
15.1 d)2) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-
15.1 d)2) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-
15.1 d)5) ( Loss of mass in air oven- Insulation )	-
15.1 d)5) ( Loss of mass in air oven- sheath )	-
15.1 d)3) (Phyaical tests for insulation : Shrinkage )	-
15.1 d)3) (Phyaical tests for insulation : Shrinkage - Crack observed )	-
15.1 d)3) (Phyaical tests for Sheath : Shrinkage )	-
15.1 d)3) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-
15.1 d)4) (Hot deformation : Insulation )	-
15.1 d)4) (Hot deformation : Sheath )	-
15.1 d)6) (Heat shock test- Insulation )	-
15.1 d)6) (Heat shock test- sheath )	-
15.1 d)7) (Thermal stability- insulation )	-
15.1 d)7) (Thermal stability- Sheath )	-
15.1 e) (Insulation resistance test : Volume Resistivity )	-
15.1 e) (Insulation resistance test : IR Constant )	-
15.1 f) (High voltage test ( water immersion test ))	-
15.1 g) (High voltage test at room temperature)	-
16.4 (Flammability Test)	-
15.4 a) (Cold bend test- Insulation ( Optional test))	-
15.4 a) (Cold bend test- Sheath ( Optional test))	-
15.4 b) (Cold impact test- Insulation ( Optional test))	-
15.4 b) (Cold impact test- Sheath ( Optional test))	-
15.4 c) (Armour resistance test ( for other than mining cables ).- Optional test )	-
17.1 (IDENTIFICATION : Manufacturer’s Identification)	-
17.2 (IDENTIFICATION : Cable Identification)	-
17.3 (IDENTIFICATION : Cable Code)	-
13.6 c) (ARMOURING: Torsion Test (For round wire ) )	-
13.6 d) (ARMOURING: Winding Test(For formed wire))	-
13.6 e) (ARMOURING: Uniformity of zinc coating)	-
Cl.8 (Conductor, Number of wires.)	-
Cl.8 (Conductor, Number of wires.)	-
Cl.8 (Flexibility class)	-
[(Cl.15), (d), 2] (After ageing, Elongation of Sheath [Percentage])	-

-
Except Cat C1 & C2

14969

BIS, Central Laboratory (CL)

None

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

3200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 18 (Weight)	-
Cl 15 (Length, Width & Thickness)	-
Cl 10.3 (UTM)	-
Cl 7 (Workmanship)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Clause - 5, 8.1 & 8.2 (E250, ALUMINIUM)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Carbon Equivalent- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-

-
Grade/Designation, Quality type of killing and declaration regarding micro alloying elements addition may please be declared. Sample size- 5 pcs of 5 cm x 5 cm having dia> 3mm and thickness >0.8 mm; Excluding -; Y-groove crackability test

14970

BIS, Bengaluru Branch Laboratory (BNBL)

None

IS 10086 (1982)

Specificaton for moulds for use in tests of cement and concrete

Rs 14700/- and Material testing charges as per relevan View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5.1 (Construction)	-
Cl 5.3 (Arangement for fastening / Clamping)	-

-
Test facility not available for Material Testing

Bureau of Indian Standards

The National Standards Body of India

Search by IS Number