BIS - LIMS (Laboratory Information Management System)

Search by IS Number

Reset

15546 Results

S.No.

Lab Name

Osl Code

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

15061

BIS, Central Laboratory (CL)

None

IS 253 (2014)

Specification for common salt (Fourth Revision)

6690 View breakup
Total testing charges for common Salt = Rs 6651/- Total testing charges for Dairy Salt = Rs 6726/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause -3 for common salt 3.1 ( 3.1.1 ) ( The material shall be crystalline solid, white or pale pink or light grey in colour.)	-
Clause -3 for common salt 3.1 ( 3.1.2 ) Annex-2 (Moisture The material shall contain not more than 6.0 percent by mass of moisture, on as received basis, when tested according to the method given in A-2)	-
Clause-3.2 for dairy salt (3.2.1) (The material shall be crystalline white solid and free from any visible impurities.)	-
Clause-3.2 for dairy salt (3.2.3) Annex -2 (3.2.3 Moisture The material shall contain not more than 0.5 percent by mass of moisture, on as received basis, when tested according to the methods given in A-2.)	-
Table 1 (i) Annex -4 (Water insoluble matter, common)	-
Table 1 (i) Annex -4 (Water insoluble matter, Dairy)	-
Table 1 (ii) Annex-5 (Chloride content (as NaCl)common)	-
Table 1 (ii) Annex-5 (Chloride content (as NaCl), Dairy)	-
Table 1 (iii) Annex-6 ( Matter soluble in water, other than sodium chloride, common)	-
Table 1 (iii) Annex-6 ( Matter soluble in water, other than sodium chloride, Dairy)	-
Table 1 (iv) (Calcium (as Ca), water soluble, percent by mass, common)	-
Table 1 (iv) Annex-7 (Calcium (as Ca), water soluble, percent by mass, Dairy)	-
Table 1 (v) (Magnesium (as Mg), water soluble, percent by mass, common )	-
Table 1 (v) Annex-7 (Magnesium (as Mg), water soluble, percent by mass, Dairy )	-
Table 1 (vi) (Sulphate as SO2 percent by mass, common)	-
Table 1 (vi) Annex-8 (sulphate as SO2 percent by mass, Dairy)	-
Table 1 (vii) Annex-9 (Alkalinity (as Na2CO3), common)	-
Table 1 (vii) Annex-11 (Alkalinity (as Na2CO3), Dairy)	-
Table 1 (viii) (Lead (as Pb), common)	-
Table 1 (viii) (Lead (as Pb),Dairy )	-
Table 1 (ix) (Iron (as Fe), common)	-
Table 1 (ix) (Iron (as Fe), Dairy)	-
Table 1 (x) Annex-11 (x) Arsenic (as As), common)	-
Table 1 (x) Annex-11 (x) Arsenic (as As),Dairy)	-
Table 1 (xi) Annex-12 (Copper (as Cu), common)	-
Table 1 (xi) Annex-12 (Copper (as Cu), Dairy )	-

-
-

15062

BIS, Central Laboratory (CL)

None

IS 4923 (2017)

Hollow steel sections for structural use - Specification (Third Revision)

7290 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.7.1 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.7.1 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.7.1 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.7.1 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.7.1 (Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.9.1, Table 1 (Dimensions and Properties of Hollow Sections (Depth))	-
Cl.9.1, Table 1 (Dimensions and Properties of Hollow Sections (Width))	-
Cl.9.1, Table 1 (Dimensions and Properties of Hollow Sections(Thickness))	-
Cl.9.1, Table 1 (Dimensions and Properties of Hollow Sections (Weigth))	-
10.6 ("External corner Radius/ Radii of corners-outside - SOP MT-23")	-
Cl. 10.1, 14.1, 18.1 (Straightness)	-
Cl. 10.4, Fig 2 (Concavity, X1)	-
Cl. 10.4, Fig 2 (Convexity, X2)	-
Cl. 10.5, Fig 3 (Squareness of side)	-
Cl. 10.6, Fig 4 (External Corner Radius)	-
Cl. 10.7, Fig 5 (Total twist, V)	-
Cl. 15.2, Table 3 (Tensile Strength- IS 1608)	-
Cl. 15.2, Table 3 (Yield Strength- IS 1608)	-
Cl. 15.2, Table 3 (Elongation- IS 1608)	-
Cl.7.1 (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.7.1 (Aluminium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
18.1 (Height of the internal weld fin - IS 4923)	-
11 (Oiling & Painting - IS 4923)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm;

15063

BIS, Central Laboratory (CL)

None

IS 15692 (2006)

Hexaconazole, suspension concentrate (SC) - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2.5 (Wet Sieve Test)	-
3.32 (Acidity/Alkalinity)	-
3.2.2 (Pourability (Rinsed Residue))	-
3.2.3 (Spontaneity of Dispersion)	-
3.2.4 (Suspensibiliy)	-
3.3.1 (Hexaconazole Content)	-
3.2.6 (Persistent Foam)	-

-
-

15064

BIS, Central Laboratory (CL)

None

IS 11708 (1986)

Specification for hand, mechanical

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
1.1 (Scope)	-
1.2 (Scope)	-
1.3 (Scope)	-
2,Table 1 ( Dimension)	-
3.1 (Light material)	-
3.2 (Material for cable)	-
3.3 ( Durometer hardness of Shore A 60-75 ; Appendix F of IS :9766)	-
3.4 (The functional hand)	-
3.5 (The finger)	-
5.1 (Provisions of adaption)	-
5.4 (Aluminium finger)	-
5.5 (Total weight)	-
6,6.1 (Workmanship &Finish)	-

-
-

15065

BIS, Central Laboratory (CL)

None

IS 4882 (1979)

Specification for low carbon steel wire for rivets for use in bearing industry (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1,4.1.1,5.1 (Carbon- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
4.1,4.1.1,5.1 (Sulphur- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
4.1,4.1.1,5.1 (Phosphorus- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
4.1,4.1.1,5.1 (Manganese- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
4.1,4.1.1,5.1 (Nitrogen- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm;

15066

BIS, Central Laboratory (CL)

None

IS 15848 (2009)

Zinc sulphate, monohydrate, agricultural grade - Specification

6300/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (Description)	-
3.2.Table 1.i (Zinc (as Zn))	-
3.2.Table 1.ii (Magnesium (as Mg)	-
3.2.Table 1.iii (Copper (as Cu))	-
3.2.Table 1.iv (Lead (as Pb))	-
3.2.Table 1.v (pH of 5 percent solution)	-
3.2.Table 1.vii (Iron (as Fe))	-

-
-

15067

BIS, Central Laboratory (CL)

None

IS 4454 : Part 4 (2001)

Steel wires for mechanical springs: Part 4 stainless steel wire (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Table 1. Cl.1.1,1.2,7.1 & 7.2 (Carbon- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
Table 1. Cl.1.1,1.2,7.1 & 7.2 (Suphur- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
Table 1. Cl.1.1,1.2,7.1 & 7.2 (Phosphorous- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
Table 1. Cl.1.1,1.2,7.1 & 7.2 (Manganese- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
Table 1. Cl.1.1,1.2,7.1 & 7.2 (Nickel- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
8 (Freedom from defects)	-
9 (Dimensions & Tolerances)	-
10.1 (Tensile test)	-
10.2 (Wrapping test)	-
10.3 (Reverse torsion test)	-
10.5 (Bend test)	-
11 (Surface finish)	-

-
-

15068

BIS, Eastern Regional Laboratory (ERL)

None

IS 8952 (1995)

Steel ingots, blooms and billets for production of mild steel wire rods for general engineering purposes - Specification (First Revision)

All grades except for the tests mentioned in remarks

4840 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4,7.1 Table 1 (Carbon- IS 228 or any other established instrumental /Chemical method)	-
4,7.1 Table 1 (Manganese- IS 228 or any other established instrumental /Chemical method)	-
4,7.1 Table 1 (Sulphur- IS 228 or any other established instrumental /Chemical method)	-
4,7.1 Table 1 (Phosphorous- IS 228 or any other established instrumental /Chemical method)	-
4,7.1 Table 1 (Silicon- IS 228 or any other established instrumental /Chemical method)	-
9 (Freedom from defects , IS 8952)	-
10 ,a) (Macro examination - IS 11371)	-
11,12 (Dimensions & Tolerance)	-
Clause 4,7.1 (Aluminium)	-
Clause 4,7.1 (Titanium)	-
9 (Freedom from defects , IS 8952)	-
10 ,a) (Macro examination - IS 11371)	-
11,12 (Dimensions & Tolerance)	-
10 ,c) (Inclusion content - IS 4163)	-
4,7.1 Table 1 (Nb- IS 228 or any other established instrumental /Chemical method)	-
Clause 4,7.1 (Vanadium)	-

-
Chemical- Except Cu. Grades to be declared

15069

BIS, Northern Regional Laboratory (NRL)

None

IS 3650 (1981)

Specification for combination side cutting pliers (Second Revision)

2850/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3 Table 1 (Dimensions- L)	-
3 Table 1 (Dimensions- a)	-
3 Table 1 (Dimensions- b)	-
3 Table 1 (Dimensions- c1)	-
3 Table 1 (Dimensions- e)	-
3 Table 1 (Dimensions- h)	-
3 Table 1 (Dimensions- h1)	-
3 Table 1 (Dimensions- t)	-
4 (Hardness- Near cutting edges)	-
4 (Hardness- Body gripping surfce)	-
3 Table 1 (Dimensions- t)	-

-
Excluding Tortion , handle load, bend test and Hard wire cutting test

15070

BIS, Central Laboratory (CL)

None

IS 4398 (1994)

Carbon - Chromium steel for the manufacture of balls, rollers and bearing races - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 5.1 & Table 1 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.1 & Table 1 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.1 & Table 1 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.1 & Table 1 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm;

15071

BIS, Central Laboratory (CL)

None

IS 10243 (1993)

2,4 - D ethyl ester EC- Specificationn (First Revision)

Rs.2750.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2 (Description)	-
3.3 (Identity Test)	-
3.4.1 (Cold Test)	-
3.4.2 (Flash Point (Abel))	-
3.4.3 (Emulsion Stability)	-
3.5.1 (2,4-D Ethyl Ester EC content)	-
3.5.2 (Fee 2,4-D)	-

-
-

15072

BIS, Western Regional Laboratory (WRL)

None

IS 1029 (1970)

Specification for hot-rolled steel strip (Baling) (First Revision)

Rs.750/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.4 (Sulphur -IS 228 or method specified in relevant ISO standard)	-
Cl.4 (Phosphorus -IS 228 or method specified in relevant ISO standard)	-

-
-

15073

BIS, Central Laboratory (CL)

None

IS 4397 (1999)

Cold - Rolled carbon steel strips for ball and roller bearing cages retainers - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 5.2, 6.1, 6.1.1, 6.2 Table 1 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.2, 6.1, 6.1.1, 6.2 Table 1 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.2, 6.1, 6.1.1, 6.2 Table 1 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.2, 6.1, 6.1.1, 6.2 Table 1 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm;

15074

BIS, Central Laboratory (CL)

None

IS 4224 (1972)

Specification for steel wire for staples, pins and clips (First Revision)

525 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 3.1, Table 1 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 3.1, Table 1 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 3.1, Table 1 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 3.1, Table 1 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm;

15075

BIS, Central Laboratory (CL)

None

IS 4223 (1975)

Steel Wire For Umbrella Ribs

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 6.1 (Sulphur- Appropriate parts of IS 228.)	-
Cl 6.1 (Phosphorus- Appropriate parts of IS 228.)	-
7 (Freedom rom defects , IS 4223)	-
8,9 (Sizes and Tolerances - IS 4223)	-
10.1, Table 1 (Mechanical ptoperties - IS 1608(Pt -1))	-
10.2 (Torsion Test - IS 1717)	-
10.3 (Reverse Bend Test--IS 1716)	-
10.4 ( Straightness Test - IS 4223)	-
10.5 (Deflection Test - IS 4223)	-
12 (Rust Protection-IS 4223)	-
Cl. 6.1 (Sulphur- IS 228(Part 9))	-
Cl. 6.1 (Phosphorous- IS 228(Part 3))	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm;

15076

BIS, Northern Regional Laboratory (NRL)

None

IS 5986 (2017)

Hot rolled steel sheet, plate and strip for forming and flanging purposes - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (UTM)	-
Cl 9 (Press)	-
Cl 10 (Sudden Load Applied)	-
Cl 11 (Expansion Test)	-
Cl 14 (Weldability)	-
Cl 15 (Length, Width & Thickness)	-
Cl 13 (Workmanship)	-
7.1 (Carbon %)	-
7.1 (Manganese %)	-
7.1 (Phosphorus %)	-
7.1 (Sulphur %)	-
7.1 (Silicon %)	-
7.1 (CE)	-
7.1 ( Nitrogen%)	-

-
Excluding Microalloying Elements

15077

BIS, Western Regional Laboratory (WRL)

None

IS 15961 (2012)

Hot dip aluminium - Zinc alloy metallic coated steel strip and sheet (Plain)

Rs.4990 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (UTM)	-
Cl 9 & Table 2 (Workmanship)	-
Cl 12 (Weight)	-
Cl 10 (Coating Adhesion )	-
Cl 13 (Length, Width, Thickness, Camber, Deviation From Squareness & Deviation From Flatness)	-
Cl 11 (Workmanship)	-
Cl. 13.7 (Deviation from Flatness (Steepness))	-
Cl. 13.6 (Deviation from Squareness (Out of Square))	-
Cl. 13.5 (Camber)	-
4, 5 (CARBON)	-
4, 5 (SULPHUR)	-
4, 5 (PHOSPHURS)	-
4.5 (MANGANESE)	-
Clause 9 (Coating Test (Triple Spot Test) (Total Both Surface))	-
Clause 9 (Coating Test (Single Spot Test) (Total Both Surface))	-
Clause 9 (Coating Test (Single Spot Test) (One Surface))	-

-
-

15078

BIS, Central Laboratory (CL)

None

IS 3975 (1999)

Low carbon galvanized steel wires, formed wires and tapes for armouring of cables - Specification (Third Revision)

Rs 2700/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 6.1, Table-1 (Sulphur)	-
Clause 6.1, Table-1 (Phosphorus)	-
7 (Dimensions)	-
11 (Freedom from defects)	-
9.1 (Galvanizing Requirements )	-
8.1 (Mechanical Properties (as per table 5 of IS 1608))	-
8.2 (Mechanical Properties (as per IS 1717))	-
8.3 (Mechanical Properties (as per IS 1755))	-
14 (Marking)	-
14 (a) (Marking)	-
14 (b) (Marking)	-
14 (c) (Marking)	-
14 (d) (Marking)	-
14 (e) (Marking)	-
14 (f) (Marking)	-
14 (g) (Marking)	-
14.2 (Marking)	-
7 (Dimensions)	-
7 (Dimensions)	-
7 (Dimensions)	-
7 (Dimensions)	-
7 (Dimensions)	-
11 (Freedom from defects)	-
9.1 (Galvanizing Requirements )	-
9.2 (Galvanizing Requirements )	-
9.3 (Galvanizing Requirements )	-
8.1 (Mechanical Properties (as per table 5 of IS 1608))	-
8.1 (Mechanical Properties (as per table 5 of IS 1608))	-
8.2 (Mechanical Properties (as per IS 1717))	-
8.3 (Mechanical Properties (as per IS 1755))	-
8.4 (Mechanical Properties (as per IS 10810(Part- 42)))	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm; Excluding Except coating;

15079

BIS, Central Laboratory (CL)

None

IS 11646 : Part 2 (1986)

Specification for cane for visually handicapped: Part 2 folding type

Rs 4350/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2 (. Shape and Dimensions - As shown in Fig. 1.)	-
3.1 (Shaft/Tube)	-
3.2 (Grip)	-
3.3 (Tip)	-
3.4 (Coating)	-
3.5 (Inner Element)	-
2 (. Shape and Dimensions - As shown in Fig. 1.)	-
4.2 (GripThe grip may preferably be made of rubber compound. It may be moulded as shown in Fig. 1. The moulded grip shall have broader end at the top and gradually tapering at the lower end. The grip shall have flat surface in one bf the segment and the remaining portion may have a few ( 2 or 3 ) serrations for better grip. The weight of the grip shall be 70 to 90 g and length 175 to 225 mm. The grip shall be fixed on one end of the shaft with a strong adhesive. The hollowness may be filled in with a plastic button peg. The grip may have an elastic loop for handle at the top of)	-
4.1 (Shaft shall be made of tube of high tensile strength and ductility. The wall thickness of the tu-bes shall be minimum of 1 mm and outside~diameter of the tube at the centre shall be 12’5 mm minimum. The total length of the cane shall vary between 1 000 and 1 450 mm in steps of 50 mm.There may be 2 to 4 shafts which make it foldable)	-
4.3 (Ths tip may be made from suitable plastics as applicable to plastics for gear specified in IS : 7078-1973 ‘Specification for plastics used in instrument industry’ or any other material having property of good auditory impulse. The length of the tip outside the cane shall be 30 to 50 mm. The tip may have a peg hole at one end which shall be fixed into the other end of the shaft by either inserting or screwing it into the tube. The diameter of the tip shall be 12’5 mm minimum, and maybe half round at the bottom.)	-
4.4 ( Joints - The joints shall be such that it shall be easily fittable after disassembling. The joints may~be of taper type or peg type. In case of taper joint one end of the shaft is tapering and the other is done shaped. In case of peg type joint, either one end of the shaft is reduced in diameter by turning or a peg button is tightly fixed in the shaft to enable it to be fitted it in the female end of the shaft. The male and female parts shall fit into each other firmly (see Fig. 3 ). The shaft shall remain attached to when a single or double elastic cord is passed through. The elastic cord shall be fixed at the grip and the other end at the peg hold at the tip.)	-
5 (. Workmanship and Finish)	-
6.1 ( Endurance Test)	-

-
-

15080

BIS, Central Laboratory (CL)

None

IS 8708 (2006)

Mancozeb wettable powder - Specification (First Revision)

Rs 3900/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2.1 (Description)	-
3.2.2 (Sieving Requirement)	-
3.2.3 (Suspensibility)	-
3.2.4 (Wettability)	-
3.3.1 (Mancozeb Content)	-
3.3.2 (Zinc Content)	-
3.3.3 (Manganese Content)	-

-
Excluding Cl. 3.3.2 & Cl. 3.3.3 Zinc & Manganese Content;

15081

BIS, Northern Regional Laboratory (NRL)

None

IS 459 (1992)

Corrugated and semi - Corrugated asbestos cement sheets - Specification (Third Revision)

6000/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5, Table 1, Figure 1,2 (Dimensions & Tolerances - Depth of Corrugation, D - Cl. 5)	-
5, Table 1, Figure 1,2 (Dimensions & Tolerances - Pitch of Corrugation, P - Cl. 5)	-
5, Table 1, Figure 1,2 (Dimensions & Tolerances - Overall width, B - Cl. 5)	-
5, Table 1, Figure 1,2 (Dimensions & Tolerances - Effective Width, C - Cl. 5)	-
5, Table 1, Figure 1,2 (Dimensions & Tolerances - Nominal Thickness, T - Cl. 5)	-

-
Excluding load bearing test

15082

BIS, Central Laboratory (CL)

None

IS 3885 : Part 2 (1992)

Steel for the manufacture of laminated springs (Railway Rollingstock): Part 2 rib and groove sections (Second Revision)

Rs. 900 Chemical View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 3.1, 6.1 & Table 1 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 3.1, 6.1 & Table 1 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 3.1, 6.1 & Table 1 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 3.1, 6.1 & Table 1 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm; Excluding Except vanadiium as per table 1;

15083

BIS, Central Laboratory (CL)

None

IS 3885 : Part 1 (1992)

Steel for the manufacture of laminated springs (Railway Rolling Stock): Part 1 flat sections - Specification (Second Revision)

Rs. 975/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 3.1, 6.1 & Table 1 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 3.1, 6.1 & Table 1 (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 3.1, 6.1 & Table 1 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 3.1, 6.1 & Table 1 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 3.1, 6.1 & Table 1 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm;

15084

BIS, Northern Regional Laboratory (NRL)

None

IS 12109 (1987)

General requirements for light duty sewing machine heads for industrial use

Rs 5880/- + Materials as per respective ISS View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.5 (Construction and Function)	-
6.2 Table 1 (Accuracy Requirement Needle Bar - Measuring Condition - Needle bar at lowermost position)	-
6.2 Table 1 (Accuracy Requirement Needle Bar - Measuring Condition - Needle bar at lowermost position)	-
6.2 Table 1 (Accuracy Requirement Thread takeup lever - Measuring Condition - Thread take up lever at top and intermediate position of motion)	-
6.1 (Accuracy Requirement)	-
6.2 Table 1 (Accuracy Requirement Thread takeup lever - Measuring Condition - Thread take up lever at top and intermediate position of motion)	-
6.2 Table 1 (Accuracy Requirement Rotating hook- Measuring Condition - With bobbin-case removed, play of rotating hook bobbin case holder )	-
6.2 Table 1 (Accuracy Requirement Rotating hook- Measuring Condition - With bobbin-case removed, play of rotating hook bobbin case holder )	-
7 Table 1 (Durability Requirements Feed machanlsm- Measuring Condition - Feed dog at the highest position above the needle plate )	-
7 Table 1 (Durability Requirements Rotating hook- Measuring Condition - With bobbin-case removed, play of rotating hook bobbin case holder )	-
7 Table 1 (Durability Requirements Arm shaft - Measuring Condition - Shaft end )	-
7 Table 1 (Durability Requirements Rotating hook shaft- Measuring Condition - Shaft end )	-
8 Table 2 (Sewing Requirement)	-
8 Table 3 (Sewing Requirement)	-
8 Table 2 (Sewing Requirement)	-
8 Table 2 (Sewing Requirement)	-
8 Table 2 (Sewing Requirement)	-
2.5 (Construction and Function)	-
2.1 (Construction and Function)	-
2.3 (Construction and Function)	-
2.4 (Construction and Function)	-
2.6 (Construction and Function)	-
2.7 (Construction and Function)	-
3.1 (Finish)	-
3.2 (Finish)	-
5 (Lubrication)	-
10 (Marking)	-
10 (Marking)	-
3.1 (Finish)	-

-
Mechanical- Complete. Chemical -Not available

15085

BIS, Northern Regional Laboratory (NRL)

None

IS 362 (1991)

Parliament Hinges -specification

2250/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1-able 2 (Dlmenslons for Aluminium Alloy Parliament Hinges-A)	-
5.1-able 2 (Dlmenslons for Aluminium Alloy Parliament Hinges-B)	-
5.1-able 2 (Dlmenslons for Aluminium Alloy Parliament Hinges-C)	-
5.1-able 2 (Dlmenslons for Aluminium Alloy Parliament Hinges-D)	-
5.1-able 2 (Dlmenslons for Aluminium Alloy Parliament Hinges-d)	-
5.1-able 2 (Dlmenslons for Aluminium Alloy Parliament Hinges-E)	-
5.1-able 2 (Dlmenslons for Aluminium Alloy Parliament Hinges-Thickness of Flap)	-
5.1-Table 4 (Dimensions for Mild Steel Parliament Hinges-A)	-
5.1-able 3 (Dimensions for Cast Brass Parliament Hinges-B)	-
5.1-able 2 (Dlmenslons for Aluminium Alloy Parliament Hinges-C)	-
5.1-able 2 (Dlmenslons for Aluminium Alloy Parliament Hinges-D)	-
5.1-able 2 (Dlmenslons for Aluminium Alloy Parliament Hinges-d)	-
5.1-able 2 (Dlmenslons for Aluminium Alloy Parliament Hinges-E)	-
5.1-able 2 (Dlmenslons for Aluminium Alloy Parliament Hinges-Thickness of Flap)	-
6.1 (MANUFACTURE-General)	-
6.1 (MANUFACTURE-General)	-
6.1 (MANUFACTURE-General)	-
6.2 (MANUFACTURE-Knuckles)	-
6.2 (MANUFACTURE-Knuckles)	-
6.2 (MANUFACTURE-Knuckles)	-
6.2 (MANUFACTURE-Knuckles)	-
6.3 (MANUFACTURE-Pins)	-
6.3 (MANUFACTURE-Pins)	-
6.3 (MANUFACTURE-Pins)	-
6.3 (MANUFACTURE-Pins)	-
6.4 (MANUFACTURE-Screw Holes)	-
6.5 (MANUFACTURE-Position of Holes)	-
6.5 (MANUFACTURE-Position of Holes)	-
6.5 (MANUFACTURE-Position of Holes-minimum distance from the ends of the flap)	-
6.5 (MANUFACTURE-Position of Holes-minimum distance from the inner edge)	-
6.5 (MANUFACTURE-Position of Holes)	-
7.1 (FINISH)	-
7.3 (FINISH)	-

-
Facility for chemical testing is not available

15086

BIS, Western Regional Laboratory (WRL)

None

IS 15778 (2007)

Chlorinated polyvinyl chloride (Cpvc) pipes for potable hot and cold water distribution supplies - Specification

6375 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1 IS 12235 (Part 1) Table 2 (Dimension of Pipes: Mean outside Diameter)	-
7.1,7.1.1 IS 12235 (Part 1) Table 2 (Outside Diameter at any point)	-
7.1.2 IS 12235 (Part 1) Table 2 (Wall Thickness )	-
9.2 IS 12235 (Part 3) (Opacity)	-
9.4 IS 12235(Part 5/Sec 1 and Sec 2) (Reversion Test : When tested by the method prescribed in IS 12235(Part 5/Sec 1 and Sec 2), a length of pipe 200 + 20 mm long shall not alter in length by more than 5 percent.)	-
9.5 IS 12235(Part 2) (Vicat Softening Temperature: When tested by the method prescribed in IS 12235(Part 2), the Vicat softening temperature of the specimen shall not be less than 110°C.)	-
9.6 IS 12235(Part 14) (Density)	-
10.3 IS 4985 Table 4 (Resistance to External Blow at O°C: When tested by the method prescribed in IS 4985, with classified striker mass and drop height as given in Table 4, the pipe shall have a true impact rate of not more than 10 percent.)	-
10.4 IS 12235(Part 19) (Flattening Test)	-
10.5 IS 12235(Part 13) (Tensile Strength : When tested by the method prescribed in IS 12235(Part 13), the tensile strength at yield shall not be less than 50 MPaat 27±2°C. )	-
7.1,7.1.1 IS 12235 (Part 1) Table 2 (Outside Diameter at any point)	-
7.1.2 IS 12235 (Part 1) Table 2 (Wall Thickness )	-

-
The following test facilities are not available: (1) Verification of the Malfunction temperature Cl 6.3.2 (2) Effect on water Cl.9.3 (3) Hyd. characteristics Cl.10.1 for 165 Hr and 1000 Hr (4) thermal stability test.Cl.10.2

15087

BIS, Western Regional Laboratory (WRL)

None

IS 15328 (2003)

Unplasticized Non-Pressure Polyvinyl Chloride ( PVC -U ) Pipes for use in Underground Drainage and Sewerage Systems -

3450 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1,6.1.1 IS 12235 (Part 1) Table 1 (Dimension of Pipes: Mean outside Diameter, dem)	-
6.1,6.1.1 IS 12235 (Part 1) Table 1 (Outside Diameter at any point, de)	-
6.1.2 IS 4985 Table 2 (Wall Thickness, e )	-
6.1.4, Table 3 (Dimensions of integral sockets and spigot ends :- a) Elastomeric Sealing Ringsockets and spigot ends i)Meean inside dia. Of socket, dsm)	-
6.1.4, Table 3 (ii) Min. depth of engagement, A. )	-
6.1.4 Table 3 (iii) Depth of sealing Zone C )	-
6.1.4, Table 3 (iv) Length of spigot, l1)	-
6.1.4, Table 3 (v) Chamfer length, H : Approx.)	-
6.1.4.1 (wall thickness of sockets e2 min=0.9e )	-
6.1.4, Table 4 (b) Solvent Cement Joint sockets and spigot ends i) Mean inside dia. Of socket, dsm)	-
6.1.4, Table 4 (ii) Length of Solvent Cement socket, l2 )	-
6.1.4, Table 4 (iii) Length of spigot, l1, 100 mm Min.)	-
6.1.4, Table 4 (iv) Chamfer length, H, 7 mm Approx.)	-
7.3 IS 1223S ( Part 2) (Vicat Softening Temperature When determined according to IS 1223S ( Part 2), shall not be lessthan 79°C.)	-
7.4 IS 1223S ( Part 5) (Longitudinal Reversion: When tested according to the methodprescribed in IS 1223S ( Part 5), shall not exceed ± 5 percent. The pipe shall not exhibit any blisters, bubbles or crackson completion of the test.)	-
8.3 IS 12235 ( Part 8/ Sec 1 ) Table 6 (Resistance to internal Hydrostatic Pressure(Type Test) a) Acceptance Test:(1h at 27 0 C) )	-
6.1.3 (Length of Pipe)	-
8.1 Annex B (Resistance to External Blows at 0ºC: When tested according to the method prescribed in Annex B, the pipes hall have a true impact rate of not more than I0 percent.)	-

-
The following test facilities are not available: (1) Ring Stiffness (2)Elastomeric Sealing ring (3)Internal Hydrostatic Pressure for sealing ring joints (4)Intenal negative hydrostatic pressure set up. (5)Effect on water (6) TF above 250 mm

15088

BIS, Western Regional Laboratory (WRL)

None

IS 14899 (2014)

Liquefied petroleum gas (LPG) containers for automotive use - Specification (First Revision)

21363 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
10.1.5 (Inner surface in tension)	-
10.1.5 (Outer surface in tension)	-
10.1.8 (Water Capacity)	-
10.1.6 (Macroscopic Examination On Circumferential Weld )	-
10.1.6 (Macroscopic Examination On longitudinal Weld)	-
10.1.6.1 (Macroscopic Examination, m1,Through valve boss )	-
10.1.6.1 (Macroscopic Examination, m2,Through valve plate welds)	-
11 (Surface coating and colour)	-

-
Test facilities are not available for the following: (1) ( Cl. 10.5.1) - Radiographic examinations, (2) (Cl.10.6.1) Bonfire test, (3) (Cl.10.6.3) - Crash test, (4) (cl.10.6.2) - Fatigue Test (5) Chemical composition( Ni, Cr, N )

15089

BIS, Bengaluru Branch Laboratory (BNBL)

None

IS 12330 (1988)

Specificatioon for sulphate resisting Portland cement

Rs.12900/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 - Table - 1 i (Ratio of percentage of lime to percentages of silica, alumina and iron oxide - Cl 4 of IS 4032:1985)	-
4.1 - Table - 1 ii (Insoluble residue - Cl 4.10 of IS 4032:1985)	-
4.1 - Table - 1 iii (Magnesia - Cl 4.8 of IS 4032:1985)	-
4.1 - Table - 1 iv (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-
4.1 - Table - 1 vi (Tetracalcium alumino ferrite phase plus twice the tricalcium aluminate ( C4AF + 2C3A ) - Cl 4 of IS 4032:1985)	-
4.1 - Table - 1 vii (Total loss on ignition - Cl 4.2 of IS 4032:1985)	-
4.1 - Table - 1 v (Tricalcium aluminate (C3A) - Cl 4 of IS 4032:1985)	-
5.1 (Fineness 4031 Part 2)	-
5.2.1 (Expansion by Le Chatelier- 4031 Part 3)	-
5.2.1.1 (Expansion after aeration- 4031 Part 3)	-
5.2.1 (Expansion by Autoclave- 4031 Part 3)	-
5.2.1.1 (Expansion after aeration- 4031 Part 3)	-
5.3 a) (Setting Time Initial- 4031 Part 5)	-
5.3 b) (Setting Time Final- 4031 Part 5)	-
5.5 i) (Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-
5.5 ii) (Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-
5.5 iii) (Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-

-
Expect(Cl 5.6 Transverse Strength)

15090

BIS, Western Regional Laboratory (WRL)

None

IS 13997 (2014)

Drums, large open top - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5, Table 1 (Dimensions-D2)	-
5, Table 1 (Dimensions-D3)	-
5, Table 1 (Dimensions-D4)	-
5, Table 1 (Dimensions-H1)	-
5, Table 1 (Dimensions-H5)	-
5, Table 1 (Dimensions-h2)	-
5, Table 1 (Dimensions-h3)	-
5, Table 1 (Dimensions-h4)	-
5, Table 1 (Dimensions-p1)	-
6.2 (The nominal thickness of steel sheets for body and ends )	-
7.2 ( CONSTRUCTION)	-
7.3 ( CONSTRUCTION- Double Seam/Spiral Seam/Triple Seam Construction for Grade A Drums)	-
7.4 ( CONSTRUCTION-Spiral Seam/Triple Seam Construction for Grade B Drums)	-
7.4 ( CONSTRUCTION-Spiral Seam/Triple Seam Construction for Grade B Drums-Seam rolling layers)	-
7.5 ( CONSTRUCTION)	-
7.6 ( CONSTRUCTION)	-
7.7 ( CONSTRUCTION)	-
7.8 ( CONSTRUCTION- crest to trough gap)	-
7.8 ( CONSTRUCTION- no of corrugations on the body Each side)	-
7.9 (Closures)	-
7.10(a) (Closures)	-
7.10(b) (Closures)	-
7.10(c) (Closures)	-
7.10(d) (Closures)	-
7.11 ( Locking Ring)	-
8.1 (FINISH )	-
9 (leakage test)	-

-
-

Bureau of Indian Standards

The National Standards Body of India

Search by IS Number