BIS - LIMS (Laboratory Information Management System)

Search by IS Number

Reset

15558 Results

S.No.

Lab Name

Osl Code

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

15451

BIS, Guwahati Branch Laboratory (GBL)

None

IS 2098 (1997)

Asbestos cement building boards - Specification (First Revision)

3300.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8.3 Table 1 & 7.1 (TESTS-Measurement of Thickness )	-
8.4 (TESTS-Water Absorption Test )	-
11 (MARKING-Each board shall be stamped or marked by any suitable method on non weathering side with the following information: )	-
Cl. 7.1 Table -1 (Cl. 7.1 ,Table-1 (Length))	-
Cl. 7.1 Table -1 (Cl. 7.1 , Table-1 (Width))	-
Cl. 7.2 Table -1 (Cl. 7.1 , Table-1 (Thickness))	-
Cl.6 (General apperance and finish)	-
Cl. 8.2 (Cl. 8.2 ,Tests-Load Bearing Capacity test, Class A/B/C ,Average Load)	-
Cl. 8.2 (Cl. 8.2 ,Tests-Load Bearing Capacity test, Class-A/B/C , Individual Load )	-

-
Qty. required 2 Sheets (Full size)

15452

BIS, Bengaluru Branch Laboratory (BNBL)

None

IS 1507 (1977)

Specification for copper oxychloride water dispersible powder concentrates

Rs 2700/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.2.1 (Description)	-
Cl. 2.3, Table-1 (Copper Content)	-
Cl. 2.3, Table-1 (Suspensibility)	-
Cl. 2.3, Table-1 (pH of one percent aqueous dispersion)	-

-
Complete for chemical section.

15453

BIS, Guwahati Branch Laboratory (GBL)

None

IS 1626 : Part 3 (1994)

Asbestos Cement Building types and Pipe Fittings, Gutters and Gutter Fittings and Roofing Fittings - Part 3 : Roofing Fittings

Rs.3300.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 Table-1 (Shapes)	-
6.1 (Physical requirements)	-
7 (Genaral appearance and finish)	-
10 (Marking)	-
6.2 (Impermeability test according to the Method 1 described in IS 5913 : 1989)	-
Cl. 5.2 (Cl. 5.2 Outer Thickness)	-
Cl. 5.2 (Cl. 5.2 Inner Thickness)	-
Cl. 5.2 (Cl. 5.2, Outer Length)	-
Cl. 5.2 (Cl. 5.2, Inner Length )	-

-
Qty. required One Pair (One Inner & One Outer)

15454

BIS, Bengaluru Branch Laboratory (BNBL)

None

IS 1011 (2002)

Biscuits - Specification (Fourth Revision)

3280 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.3 Table 2 i (Moisture)	-
6.3 Table 2 ii (Acid insoluble ash (on dry basis))	-
6.3 Table 2 iii (Acidity of extracted fat (as oleic acid))	-
6.1 (General Requirement)	-

-
Complete for chemical section.

15455

BIS, Guwahati Branch Laboratory (GBL)

None

IS 1328 (1996)

Veneered Decorative Plywood -Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Grade - For BWR)	-
4.1 (Grade - For MR)	-
4.2 (Type - For Type 1)	-
4.2 (Type - For Type 2)	-
7.1.1 (Requirements - Open splits, checks or open joints - For Type 1 - Cl. 7.1.1)	-
7.2.1 (Requirements - Open splits, checks or open joints - For Type 2 - Cl. 7.2.1)	-
7.1.2 (Requirements - Other defects - For Type 1 - Cl. 7.1.2)	-
7.2.2 (Requirements - Other defects - For Type 2 - Cl. 7.2.2.)	-
7.1.3 (Requirements - Other Charcteristics and Manufacturing Defects - For Type 1 - Cl. 7.1.3)	-
7.2.3 (Requirements - Other Charcteristics and Manufacturing Defects - For Type 2 - Cl. 7.2.3)	-
8 (Dimensions & Tolerances - Length - Cl. 8)	-
8 (Dimensions & Tolerances - Width - Cl. 8)	-
8 (Dimensions & Tolerances - Thickness - Cl. 8)	-
8 (Dimensions & Tolerances - Edge Straightness - Annexure C)	-
8 (Dimensions & Tolerances - Squareness - Annexure C)	-
9 (Finish - Cl. 9.1, 8.3)	-
9 (Finish - Cl. 9.2, 8.3)	-
11 (Tests - Moisture Content - Part 1 of IS 1734)	-
11 (Tests - Water Resistance Test - Cl. 11.1.2.1 [for MR Grade])	-
11 (Tests - Water Resistance Test - Cl. 11.1.2.2 [for BWR Grade])	-

-
Qty. required 1 Nos

15456

BIS, Eastern Regional Laboratory (ERL)

None

IS 3074 (2013)

Steel tubes for automotive purposes - Specification (Third Revision)

All grades except for the tests mentioned in remarks

4200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7, 20,Table 1,2,4 &6 ( C)	-
7, Table 1,2,4 &6 (Mn)	-
7, Table 1,2,4 &6 (S)	-
7, Table 1,2,4 &6 (P)	-
7, Table 1,2,4 &6 (Si)	-
7, Table 1,2,4 &6 (Ni)	-
7, Table 1,2,4 &6 (Cr)	-
7, Table 1,2,4 &6 (Mo)	-
8.2,15,17,22, Table 3,5 &7 (Tensile Tests,IS 1608 Part 1)	-
8.3,18, (Flattening Test)	-
6 (STRAIGHTNESS)	-
21 (Condition)	-
3.2.1 (Height of internal fin)	-
10 (Surface protection)	-

-
Facility not available for leak tightness test. Grade designation, type, class, condition to be declared. Chem- Complete for CDS but Partial for ERW,CEW (facility not available for micro alloying elements)

15457

BIS, Bengaluru Branch Laboratory (BNBL)

None

IS 12701 (1996)

Rotational moulded polyethylene water storage tanks - specification (First Revision)

6900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2.3 (Carbon Black Content )	-
4.2.3 (Carbon Dispersion Test)	-
5.1 Table 1 (Dimensioas of Cylinderical Vertical Tank)	-
5.1 Table 1 (Dimensioas of Cylinderical Vertical Tank)	-
5.1 Table 1 (Dimensioas of Cylinderical Vertical Tank)	-
5.1 Table 1 (Dimensioas of Cylinderical Vertical Tank)	-
5.1 Table 1 (Dimensioas of Cylinderical Vertical Tank)	-
5.1 Table 1 (Dimensioas of Cylinderical Vertical Tank)	-
5.1 Table 1 (Dimensioas of Cylinderical Vertical Tank)	-
5.1 Table 1 (Dimensioas of Cylinderical Vertical Tank)	-
5.2 Table 2 (Dimensions of Rectangular Loft Tanks)	-
5.2 Table 2 (Dimensions of Rectangular Loft Tanks)	-
5.2 Table 2 (Dimensions of Rectangular Loft Tanks)	-
5.2 Table 2 (Dimensions of Rectangular Loft Tanks)	-
5.2 Table 2 (Dimensions of Rectangular Loft Tanks)	-
5.2 Table 2 (Dimensions of Rectangular Loft Tanks)	-
5.3 (Types and Features )	-
7.1.1 (Resistance to Deformation)	-
7.1.2 (Resistance to Deformation)	-
7.2 (Resistance to Impact)	-
7.4 (Tensile Strength)	-
7.5 (Flexural Modulus)	-
7.6 (overall Migration)	-
6.1 (Finish)	-
9.2.1 (Man-Hole and Hand-Hole Lids)	-
9.2 (Man-Hole and Hand-Hole Lids)	-
9.1 (Lid Thickness)	-
7.3 (Test for Top Load Resistance)	-
6.1 (Finish)	-
5.4 (Wall Thickness above effective height)	-
5.2 Table 2 (7) (Minimum Wall Thickness)	-
5.1 Table 1 (7) (Minimum Weight of Tank (Without Lid))	-
9.1 (Man-Hole and Hand-Hole Lids)	-
7.6 (overall Migration)	-

-
Excluding: Available up to 3000 L capacity and except for Cl No 4.1 (Material) , 4.2(anti-oxidants), 4.2.1(density of resin), 4.2.2(melt flow rate), 4.3 (Reworked material).

15458

BIS, Patna Branch Laboratory (PBL)

None

IS 9295 (1983)

Specification for steel tubes for idlers for belt conveyors (First Revision)

Rs 5100/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1 (Sulphur- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
7.1 (Phosphorous- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
8.1.1 Table 1 (Tensile Strength- IS 1608(1))	-
8.1.1 Table 1 (Yield Strength- IS 1608)	-
8.1.1 Table 1 (Elongation Percent- IS 1608)	-
9.1 Table 2 (Outside Diameter)	-
9.1 Table 2 (Thickness)	-
9.1 Table 2 (Mass)	-
10 (Hardness)	-
13.1.1 (Ovality)	-
13.1.2 (Eccentricity)	-
15.1 (Straightness)	-
16.1 (Length)	-
17.1 (Surface Protection)	-

-
All test facilities are available as per the IS except i. Hardness Test (Clause 10)

15459

BIS, Patna Branch Laboratory (PBL)

None

IS 5986 (2017)

Hot rolled steel sheet, plate and strip for forming and flanging purposes - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (UTM)	-
Cl 15 (Length, Width & Thickness)	-
Cl 9 (Press)	-
Cl 13 (Workmanship)	-
7.1 (Carbon %)	-
7.1 (Manganese %)	-
7.1 (Phosphorus %)	-
7.1 (Sulphur %)	-
7.1 (Silicon %)	-
7.1 ( Nitrogen%)	-
7.1 (CE)	-
Cl. 8.3, Table 6 & 7 ( Elongation at 5.65√A Gauge length)	-
Cl. 8.3, Table 6 & 7 (Elongation at 80 mm gauge length)	-
Cl. 8.3, Table 6 & 7 (Elongation at 50 mm gauge length)	-
Cl. 8.3, Table 6 & 7 (Yield strength)	-

-
All test facilities are available as per the IS except- i) Hole Expansion Ratio Test (Clause 11) and ii. Impact Test (Clause 10) facility is out of order

15460

BIS, Patna Branch Laboratory (PBL)

None

IS 4923 (2017)

Hollow steel sections for structural use - Specification (Third Revision)

7290 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.7.1 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.7.1 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.9.1, Table 1 (Dimensions and Properties of Hollow Sections (Depth))	-
Cl.9.1, Table 1 (Dimensions and Properties of Hollow Sections (Width))	-
Cl.9.1, Table 1 (Dimensions and Properties of Hollow Sections(Thickness))	-
Cl.9.1, Table 1 (Dimensions and Properties of Hollow Sections (Weigth))	-
Cl.9.1, Table 1 (Dimensions and Properties of Hollow Sections (Area of Section))	-
Cl.9.1, Table 1 (Dimensions and Properties of Hollow Sections (Moment of Inertia))	-
Cl.9.1, Table 1 (Dimensions and Properties of Hollow Sections (Radius of Gyration))	-
Cl.9.1, Table 1 (Dimensions and Properties of Hollow Sections(Elastic Modulus))	-
Cl.9.1, Table 1 (Dimensions and Properties of Hollow Sections (Plastic Modulus))	-
Cl. 10.1, 14.1, 18.1 (Straightness)	-
Cl. 10.2, Fig 1 (Outside dimension (B))	-
Cl. 10.2, Fig 1 (Outside dimension (H))	-
Cl. 10.2, Fig 1 (Outside dimension (T))	-
Cl. 10.4, Fig 2 (Concavity, X1)	-
Cl. 10.4, Fig 2 (Convexity, X2)	-
Cl. 10.5, Fig 3 (Squareness of side)	-
Cl. 10.6, Fig 4 (External Corner Radius)	-
Cl. 10.7, Fig 5 (Total twist, V)	-
Cl. 15.2, Table 3 (Tensile Strength- IS 1608)	-
Cl. 15.2, Table 3 (Yield Strength- IS 1608)	-
Cl. 15.2, Table 3 (Elongation- IS 1608)	-
Cl. 14.1 (Exact Length)	-
Cl. 14.1 (Random Length)	-
Cl. 14.1 (Weight on individual length)	-
Cl.7.1 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.7.1 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.7.1 (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.7.1 (Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.7.1 (Carbon Equivalent-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 18, Note 2 (Internal Fin Height (Only for Cold Formed))	-

-
Complete test facility available.

15461

BIS, Patna Branch Laboratory (PBL)

None

IS 3975 (1999)

Low carbon galvanized steel wires, formed wires and tapes for armouring of cables - Specification (Third Revision)

Rs 2700/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8.1 (Mechanical Properties (as per table 5 of IS 1608))	-
8.1 (Mechanical Properties (as per table 5 of IS 1608))	-
8.3 (Mechanical Properties (as per IS 1755))	-
8.2 (Mechanical Properties (as per IS 1717))	-
9.1 (Galvanizing Requirements )	-
9.2 (Galvanizing Requirements )	-
9.3 (Galvanizing Requirements )	-
6.2 (Phosphorus %)	-
6.2 (Sulphur %)	-
Clause 6.1, Table-1 (Sulphur)	-
Clause 6.1, Table-1 (Phosphorus)	-
11 (Freedom from defects)	-
7 (Dimensions)	-
11 (Freedom from defects)	-
8.1 (Mechanical Properties (as per table 5 of IS 1608))	-
8.1 (Mechanical Properties (as per table 5 of IS 1608))	-
8.2 (Mechanical Properties (as per IS 1717))	-
8.3 (Mechanical Properties (as per IS 1755))	-

-
Test facilities are available as per the IS except- i. Wrapping Test (Clause 8.3) upto 2 mm mandrel not available ii. Adhesion Test (Clause 9.3)

15462

BIS, Patna Branch Laboratory (PBL)

None

IS 3589 (2001)

Steel pipes for water and sewage (168.3 To 2540 Mm Outside Diameter) - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8.1 Table 2 Table 3 (Carbon Content IS 228)	-
8.1 Table 2 Table 3 (Manganese Content IS 228)	-
8.1 Table 2 Table 3 (Phosphorus Content IS 228)	-
8.1 Table 2 Table 3 (Sulphur Content IS 228)	-
11.1, Table 5. (Outside Diameter (OD))	-
11.1, Table 5. (Thickness)	-
11.1, Table 5. (Mass)	-
12.3.3 (Ovality)	-
12.5 (Strightness)	-
14.1 (Visual inspection, Appearance and Workmanship)	-
14.2 (Visual inspection, Appearance and Workmanship)	-
14.3 (Visual inspection, Appearance and Workmanship)	-
14.4 (Visual inspection, Appearance and Workmanship-Dent Depth(below 610 mm OD))	-
14.4 (Visual inspection, Appearance and Workmanship-Dent Depth(Above 610 mm OD))	-
14.4 (Visual inspection, Appearance and Workmanship-Dent Length)	-
14.4 (Visual inspection, Appearance and Workmanship-Dent Length)	-
9.1 (Tensile test-Yield Strength)	-
9.1 (Tensile test-Strength)	-
9.1 (Tensile test- Elongation)	-
9.3 (Guided Bend Test (for SAW Pipes))	-
9.2.3 (Flattening Test for seamless pipes)	-
9.2.1 (Flattening test for ERW pipes )	-

-
Except i Hydraulic Pressure Test (The Hyrostatic Test has to be carried out at the manufacturer's end only.) ii dimentions Size above 219.1 mm OD iii. Ovality Test Facility is not available for size 273 mm and above (Clause 12.3.3)

15463

BIS, Patna Branch Laboratory (PBL)

None

IS 299 (2012)

Alumino - Ferric - Specification (Fifth Revision)

Rs.3250.00 (for Grade 1, 2 & 3) and Rs.8250.00 (for Gra View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
1 (i) Table 1 ( Insouble matter, Grade 1, A-3)	-
1 (ii) Table 1 (Soluble iron compound (as Fe2+ and Fe3+), Grade 1, A-4)	-
1 (iii) Table 1 (Water soluble aluminium compounds (as Al2O3), Grade 1, A-5)	-
1 (iv) Table 1 (pH (of 5 percent aqueous solution), Grade 1, A-6)	-
1 (v) Table 1 (Free acidity (as H2SO4)/Basicity (as Al2O3), Grade 1, A-7)	-
1 (i) Table 1 ( Insouble matter, Grade 2, A-3)	-
1 (i) Table 1 ( Insouble matter, Grade 3, A-3)	-
1 (i) Table 1 ( Insouble matter, Grade 4, A-3)	-
1 (i) Table 1 ( Insouble matter, Grade 5, A-3)	-
1 (ii) Table 1 (Soluble iron compound (as Fe2+ and Fe3+), Grade 2, A-4)	-
1 (ii) Table 1 (Soluble iron compound (as Fe2+ and Fe3+), Grade 3, A-4)	-
1 (ii) Table 1 (Soluble iron compound (as Fe2+ and Fe3+), Grade 4, A-4)	-
1 (ii) Table 1 (Soluble iron compound as Fe2+ and Fe3+), Grade 5, A-4)	-
1 (iii) Table 1 (Water soluble aluminium compounds (as Al2O3), Grade 2, A-5)	-
1 (iii) Table 1 (Water soluble aluminium compounds (as Al2O3), Grade 3, A-5)	-
1 (iii) Table 1 (Water soluble aluminium compounds (as Al2O3), Grade 4, A-5)	-
1 (iii) Table 1 (Water soluble aluminium compounds (as Al2O3), Grade 5, A-5)	-
1 (iv) Table 1 (pH (of 5 percent aqueous solution), Grade 2, A-6)	-
1 (iv) Table 1 (pH (of 5 percent aqueous solution), Grade 3, A-6)	-
1 (iv) Table 1 (pH (of 5 percent aqueous solution), Grade 4, A-6)	-
1 (iv) Table 1 (pH (of 5 percent aqueous solution), Grade 5, A-6)	-
1 (v) Table 1 (Free acidity (as H2SO4)/Basicity (as Al2O3), Grade 2, A-7)	-
1 (v) Table 1 (Free acidity (as H2SO4)/Basicity (as Al2O3), Grade 3, A-7)	-
1 (v) Table 1 (Free acidity (as H2SO4)/Basicity (as Al2O3), Grade 4, A-7)	-
1 (v) Table 1 (Free acidity (as H2SO4)/Basicity (as Al2O3), Grade 5, A-7)	-
1 (vii) Table 1 (Arsenic (as As2O3), Grade 1, A-9)	-
1 (vii) Table 1 (Arsenic (as As2O3), Grade 2, A-9)	-
1 (vii) Table 1 (Arsenic (as As2O3), Grade 3, A-9)	-
1 (vii) Table 1 (Arsenic (as As2O3), Grade 4, A-9)	-
1 (vii) Table 1 (Arsenic (as As2O3), Grade 5, A-9)	-
1 (viii) Table 1 (Mercury (as Hg), Grade 1, A-10)	-
1 (viii) Table 1 (Mercury (as Hg), Grade 2, A-10)	-
1 (viii) Table 1 (Mercury (as Hg), Grade 3, A-10)	-
1 (viii) Table 1 (Mercury (as Hg), Grade 4, A-10)	-
1 (viii) Table 1 (Mercury (as Hg), Grade 5, A-10)	-
1 (ix) Table 1 (Manganese (as Mn), Grade 1, A-11)	-
1 (ix) Table 1 (Manganese (as Mn), Grade 2, A-11)	-
1 (ix) Table 1 (Manganese (as Mn), Grade 3, A-11)	-
1 (ix) Table 1 (Manganese (as Mn), Grade 4, A-11)	-
1 (ix) Table 1 (Manganese (as Mn), Grade 5, A-11)	-
1 (x) Table 1 (Chromium (as Cr), Grade 1, A-12)	-
1 (x) Table 1 (Chromium (as Cr), Grade 2, A-12)	-
1 (x) Table 1 (Chromium (as Cr), Grade 3, A-12)	-
1 (xi) Table 1 (Cadmium (as Cd), Grade 4, A-13)	-
1 (x) Table 1 (Chromium (as Cr), Grade 5, A-12)	-
1 (xi) Table 1 (Cadmium (as Cd), Grade 1, A-13)	-
1 (xi) Table 1 (Cadmium (as Cd), Grade 2, A-13)	-
1 (xi) Table 1 (Cadmium (as Cd), Grade 3, A-13)	-
1 (xi) Table 1 (Cadmium (as Cd), Grade 4, A-13)	-
1 (xi) Table 1 (Cadmium (as Cd), Grade 5, A-13)	-
1 (xii) Table 1 (Selenium (as Se), Grade 1, A-14)	-
1 (xii) Table 1 (Selenium (as Se), Grade 2, A-14)	-
1 (xii) Table 1 (Selenium (as Se), Grade 3, A-14)	-
1 (xii) Table 1 (Selenium (as Se), Grade 4, A-14)	-
1 (xii) Table 1 (Selenium (as Se), Grade 5, A-14)	-
1 (xiii) (a) Table 1 (Organic impurities:Phenolic compounds (as C6H5OH), Garde 1, A-15)	-
1 (xiii) (a) Table 1 (Organic impurities:Phenolic compounds (as C6H5OH), Garde 2, A-15)	-
1 (xiii) (a) Table 1 (Organic impurities:Phenolic compounds (as C6H5OH), Garde 3, A-15)	-
1 (xiii) (a) Table 1 (Organic impurities:Phenolic compounds (as C6H5OH), Garde 4, A-15)	-
1 (xiii) (a) Table 1 (Organic impurities:Phenolic compounds (as C6H5OH), Garde 5, A-15)	-
1 (xiii) (b) Table 1 (Anionic detergents (as MASS), Garde 1, A-16)	-
1 (xiii) (b) Table 1 (Anionic detergents (as MASS), Garde 2, A-16)	-
1 (xiii) (b) Table 1 (Anionic detergents (as MASS), Garde 3, A-16)	-
1 (xiii) (b) Table 1 (Anionic detergents (as MASS), Garde 4, A-16)	-
1 (xiii) (b) Table 1 (Anionic detergents (as MASS), Garde 5, A-16)	-
Clause 4.1 (Description)	-

-
Complete for Grade 1,2 &3. For Grade 4 & 5 complete except Mercury

15464

BIS, Patna Branch Laboratory (PBL)

None

IS 2879 (1998)

Mild steel for metal arc welding electrodes - Specification (Third Revision)

Testing charges are Rs.9050/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 7 (Workmanship)	-
Cl 8 & 9 (Diameter)	-
6 (Carbon %)	-
6 (Manganese %)	-
6 (Phosphorus %)	-
6 (Sulphur %)	-
6 (Silicon %)	-
Cl. 9.2 (Maximum Difference between 2 readings taken at any 2 diameters across cross section)	-
Cl. 8,9 (Width across flat)	-
Cl. 8,9 (Length)	-

-
All test facilities are available .

15465

BIS, Patna Branch Laboratory (PBL)

None

IS 280 (2006)

Mild steel wire for general engineering purposes (Fourth Revision)

Rs.3750.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 7 & Table 1 (Diameter & Difference Between Two Reading On Any Two Diameters)	-
Cl 9 (Tensile Test On UTM)	-
Cl 11 (Workmanship)	-
Cl 13 (Workmanship)	-
6 AND AS PER IS 7887 (PHOSPHORUS)	-
6 AND AS PER IS 7887 (SULPHUR)	-
6 AND AS PER IS 7887 (MANGANESE)	-
6 AND AS PER IS 7887 (SILICON)	-
6 AND AS PER IS 7887 (CARBON)	-
9.2 (Wrapping Test)	-
9.3 (Bend test)	-
10 (Finish)	-
11 (Coating test)	-
13 (Freedom from defects)	-
11 (Coating test)	-

-
Test facilities are available as per the IS except- i. Wrapping Test (Clause 8.3) upto 2 mm mandrel not available

15466

BIS, Patna Branch Laboratory (PBL)

None

IS 253 (2014)

Specification for common salt (Fourth Revision)

6690 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause -3 for common salt 3.1 ( 3.1.1 ) ( The material shall be crystalline solid, white or pale pink or light grey in colour.)	-
Clause -3 for common salt 3.1 ( 3.1.2 ) Annex-2 (Moisture The material shall contain not more than 6.0 percent by mass of moisture, on as received basis, when tested according to the method given in A-2)	-
Clause-3.2 for dairy salt (3.2.1) (The material shall be crystalline white solid and free from any visible impurities.)	-
Clause-3.1 for dairy salt (3.2.2) (3.2.2 Particle Size 99 percent by mass of the material shall pass completely through 850-micron IS Sieve [see IS 460 (Part I)].)	-
Clause-3.2 for dairy salt (3.2.3) Annex -2 (3.2.3 Moisture The material shall contain not more than 0.5 percent by mass of moisture, on as received basis, when tested according to the methods given in A-2.)	-
Table 1 (i) Annex -4 (Water insoluble matter, common)	-
Table 1 (i) Annex -4 (Water insoluble matter, Dairy)	-
Table 1 (ii) Annex-5 (Chloride content (as NaCl)common)	-
Table 1 (ii) Annex-5 (Chloride content (as NaCl), Dairy)	-
Table 1 (iii) Annex-6 ( Matter soluble in water, other than sodium chloride, common)	-
Table 1 (iii) Annex-6 ( Matter soluble in water, other than sodium chloride, Dairy)	-
Table 1 (iv) (Calcium (as Ca), water soluble, percent by mass, common)	-
Table 1 (iv) Annex-7 (Calcium (as Ca), water soluble, percent by mass, Dairy)	-
Table 1 (v) (Magnesium (as Mg), water soluble, percent by mass, common )	-
Table 1 (v) Annex-7 (Magnesium (as Mg), water soluble, percent by mass, Dairy )	-
Table 1 (vi) (Sulphate as SO2 percent by mass, common)	-
Table 1 (vi) Annex-8 (sulphate as SO2 percent by mass, Dairy)	-
Table 1 (vii) Annex-9 (Alkalinity (as Na2CO3), common)	-
Table 1 (vii) Annex-11 (Alkalinity (as Na2CO3), Dairy)	-
Table 1 (ix) (Iron (as Fe), common)	-
Table 1 (ix) (Iron (as Fe), Dairy)	-
Table 1 (xi) Annex-12 (Copper (as Cu), common)	-
Table 1 (xi) Annex-12 (Copper (as Cu), Dairy )	-
Table 1 (x) Annex-11 (x) Arsenic (as As), common)	-
Table 1 (x) Annex-11 (x) Arsenic (as As),Dairy)	-

-
All test facilities are available as per the IS except tests for Lead.

15467

BIS, Patna Branch Laboratory (PBL)

None

IS 2124 (2000)

Sodium bicarbonate - Specification (Second Revision)

Rs 4660/- for Pure Grade View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (Grade)	-
4.1 (Description)	-
4.2 (Table 1 S.no.(i)) (Total Alkalinity (as NaHCO3))	-
4.2 (Table 1 S.no.(i)) (pH )	-
4.2 (Table 1 S.no.(ii)) (Chlorides (as Cl))	-
4.2 (Table 1 S.no.(iii)) (Insoluble matter)	-
4.2 (Table 1 S.no.(iv)) (Sulphates (as SO4))	-

-
All test facilities are available as per the IS

15468

BIS, Patna Branch Laboratory (PBL)

None

IS 1507 (1977)

Specification for copper oxychloride water dispersible powder concentrates

Rs 2700/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.2.1 (Description)	-
Cl. 2.3, Table-1 (pH of one percent aqueous dispersion)	-

-
All test facilities are available as per the IS

15469

BIS, Southern Regional Laboratory (SRL)

None

IS 459 (1992)

Corrugated and semi - Corrugated asbestos cement sheets - Specification (Third Revision)

Please see remarks View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5, Table 1 (Dimensions & Tolerances - Type of Sheet - cl. 5)	-
5, Table 1, Figure 1,2 (Dimensions & Tolerances - Depth of Corrugation, D - Cl. 5)	-
5, Table 1, Figure 1,2 (Dimensions & Tolerances - Pitch of Corrugation, P - Cl. 5)	-
5, Table 1, Figure 1,2 (Dimensions & Tolerances - Overall width, B - Cl. 5)	-
5, Table 1, Figure 1,2 (Dimensions & Tolerances - Effective Width, C - Cl. 5)	-
5, Table 1, Figure 1,2 (Dimensions & Tolerances - Nominal Thickness, T - Cl. 5)	-
5, Table 1, Figure 1,2 (Dimensions & Tolerances - Length of Sheet, A - Cl. 5)	-
6.1 (Load Bearing Capacity Test - Cl. 6.1, IS 5913)	-
7 (General Appearance and Finish - Cl. 7.1)	-
7 (General Appearance and Finish - Cl. 7.2)	-
12 (Marking - Indication of source of manufacture - Cl. 12)	-
12 (Marking - Year & Date of manufacture - Cl. 12)	-
12 (Marking - Pictorial warning signs as given in IS 12081 (Part 2) : 1987 - Cl. 12)	-

-
" 03 nos. " Excluding optional tests,colouring matter

15470

BIS, Patna Branch Laboratory (PBL)

None

IS 1489 : Part 2 (2015)

Portland - Pozzolana cement - Specification: Part 2 calcined clay based

Rs.8420/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 - Table - 1 i (Insoluble residue - Cl 7.4 of IS 4032:1985)	-
6 - Table - 1 ii (Magnesia - Cl 7.2 of IS 4032:1985)	-
6 - Table - 1 iii (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-
6 - Table - 1 iv (Loss on ignition - Cl 7.1 of IS 4032:1985)	-
6 - Table - 1 v (Chloride content - Cl 4.13 of IS 4032:1985)	-
6 - Table - 1 vi ( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-
7 -Table 2- i (Fineness 4031 Part 2)	-
7 -Table 2- ii- a (Expansion by Le Chatelier- 4031 Part 3)	-
7 -Table 2- ii- a (Expansion after aeration - 4031 Part 3)	-
7 -Table 2- ii- b (Expansion by Autoclave- 4031 Part 3)	-
7 -Table 2- ii- b (Expansion after aeration- 4031 Part 3)	-
7 -Table 2- iii- a (Setting Time Initial- 4031 Part 5)	-
7 -Table 2-iii- b (Setting Time Final- 4031 Part 5)	-
7 -Table 2- iv- a (Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-
7 -Table 2- iv- b (Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-
7 -Table 2- iv- c (Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-
7 -Table 2- vi (Drying Shrinkage- IS 4031 Part 10)	-

-
Except Transverse Strength (Mechanical Test) (It is an optional test as mentioned in the IS and not required for GoL.

15471

BIS, Patna Branch Laboratory (PBL)

None

IS 1148 (2009)

Steel Rivet Bars (medium And High Tensile)--For Structural Purposes--For Structural Purposes

8660 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 6 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
7 (FREEDOM FROM DEFECTS)	-
8 ( LENGTHS)	-
9 (DIMENSIONAL TOLERANCES)	-
11 (Tensile Test-1608:Part 1)	-
11 (Yield Strength, Mpa)	-
11 (Tensile Strength, Mpa)	-
11 (Elongation, %)	-
12 (Bend Test-1599)	-

-
Complete test facility available.

15472

BIS, Patna Branch Laboratory (PBL)

None

IS 1079 (2017)

Hot rolled carbon steel sheet, plate and strip - Specification (Seventh Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8, Table 5 & 6 (Tensile Strength)	-
Cl 12 (Workmanship)	-
6.1 (Carbon %)	-
6.1 (Manganese %)	-
6.1 (Phosphorus %)	-
6.1 (Sulphur %)	-
6.1 (Silicon %)	-
6.1 ( Nitrogen%)	-
8, Table 5 & 6 (Yield Strength)	-
8, Table 5 & 6 (Elongation)	-
Clause 10 (Cuppping Test)	-
Clause 12 (Freedom from defect)	-
Clause 13 (Length)	-
14 (Calculation of weight)	-
Cl.13 (Out of square)	-
Cl.13 (Flatness)	-
Cl.13 (Camber)	-
Cl.13 (Width)	-
Cl.13 (Thickness)	-
8, Table 5 & 6 (Yield Strength)	-

-
All test facilities are available as per the IS.

15473

MSME TESTING CENTRE (WR), MUMBAI

7119404

IS 651 (2007)

Glazed stoneware pipes and fittings - Specification (Sixth Revision)

Class: SP1, SP2 & SP3

9500 View breakup
Complete test charges

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(GENERAL QUALITY)	-	500	Visual inspection
7.2(Hydraulic Test)	-	2500	Hydraulic Test
7.3(Absorption Test)	-	1500	Absorption Test
Clause 7.4(Acid Resistance Test)	-	1000	Test for Acid Resistance
Clause 7.5(Alkali Resistance Test)	-	1000	Test for Alkali Resistance

-
-

15474

BIS, Patna Branch Laboratory (PBL)

None

IS 10748 (2004)

Hot - Rolled steel strip for welded tubes and pipes - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 & Table 3 (UTM)	-
Cl 9 (Press)	-
Cl 11 (Workmanship)	-
Cl 12 & 13 (Length, Width & Thickness)	-
7.1 (Carbon %)	-
7.1 (Manganese %)	-
7.1 (Phosphorus %)	-
7.1 (Sulphur %)	-
Cl. 8, Table 3 (Yield Stress)	-
Cl. 14 (Weight)	-
Cl. 12, 13 (Camber)	-
Cl. 12, 13 (Thickness)	-
Cl. 8, Table 3 (Elongation)	-
7.1 (Silicon %)	-
7.1 (CE)	-
7.1 ( Nitrogen%)	-

-
All test facilities are available as per the IS.

15475

BIS, Patna Branch Laboratory (PBL)

None

IS 1038 (1983)

Specification For Steel Doors, Windows And Ventilators

3000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1. (Size-Height)	-
4.1 (Size-Width)	-
4.3 (Designation)	-
6.1 (Frames)	-
6.1.1.1 (Visual Inspection Test)	-
6.2 (Side Hung Shutter)	-
6.2 (Side Hung Shutter)	-
6.2 (Side Hung Shutter- Thickness of hinge)	-
6.2 (Side Hung Shutter- Pin diameter)	-
6.2 (Side Hung Shutter-Width of hinge)	-
6.2.2 & 6.2.2.1 (Handle and Handle Plate- Thicknesss of handle)	-
6.2.2 & 6.2.2.1 (Handle and Handle Plate-Height of handle plate)	-
6.2.3 (Peg Stay - Thickness)	-
6.2.3 (Peg Stay - Dimensions-A)	-
6.2.3 (Peg Stay - Dimensions-B)	-
6.2.3 (Peg Stay - Dimensions-C)	-
6.2.3 (Peg Stay - Dimensions-D)	-
6.2.3 (Peg Stay - Dimensions-E)	-
6.2.3 (Peg Stay - Dimensions-F)	-
6.2.3 (Peg Stay - Dimensions-G)	-
6.2.3 (Peg Stay - Dimensions-H)	-
6.2.3 (Peg Stay - Dimensions-J)	-
6.2.3 (Peg Stay - Dimensions-K)	-
6.2.3 (Peg Stay - Dimensions-L)	-
6.2.3 (Peg Stay - Dimensions-M)	-
6.3 (Top Hung Ventilator)	-
6.3 (Top Hung Ventilator-Thickness of hinge)	-
6.3 (Top Hung Ventilator-Pin diameter)	-
6.3 (Top Hung Ventilator-Width of hinge)	-
7.1 (Position of Holes)	-
7.2 Table 2 (Position of Fixing Screws)	-
7.2 Table 2 (Lugs-A)	-
7.2 Table 2 (Lugs-B)	-
7.2 Table 2 (Lugs-C)	-
7.2 Table 2 (Lugs-D)	-
7.2 Table 2 (Lugs-E)	-
7.2 Table 2 (Lugs-F)	-
7.2 Table 2 (Lugs-G)	-
8 (Finish)	-
9 (Glazing)	-
9 (Glazing- No of glazing clip against each plate)	-

-
All test facilities are available as per the IS

15476

BIS, Southern Regional Laboratory (SRL)

None

IS 13422 (1992)

Disposable surgical rubber gloves specification

Rs.6900.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.4 (Sterility)	-
4 (TYPES)	-
5.2.1 (General Characteristics and Dimensions)	-
5.2.2 and Table 1 Fig. 1 (Dimensions - Length)	-
5.2.2 and Table 1 Fig. 1 (Dimensions - Width)	-
5.2.2 and Table 1 Fig. 1 (Dimensions - Thickness of Finger)	-
5.2.2 and Table 1 Fig. 1 (Dimensions - Thickness of Palm)	-
5.2.2 and Table 1 Fig. 1 (Dimensions - Thickness of Cuff)	-
5.3 and Table 2 ( Tensile Strength Before Ageing)	-
5.3 and Table 2 ( Elongation at Break Before Ageing)	-
5.3 and Table 2 (Stress at 500% Elongation at Break Before Ageing)	-
5.3 and Table 2 ( Tensile StrengthAfter Accelerated Ageing)	-
5.3 and Table 2 ( Elongation at Break After Accelerated Ageing)	-
5.5 (Airtight Test)	-

-
" Mech - 25 pairs, Micro - 3 pairs "

15477

BIS, Northern Regional Laboratory (NRL)

None

IS 1659 (2004)

Block boards - Specification (Fourth Revision)

Please check remarks View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
9.2.5 (Modulus of elasticity - MINIMUM INDIVIDUAL - Annexure K)	-
9.2.5 (Modulus of elasticity - AVERAGE - Annexure K)	-
9.2.5 (Modulus of rupture - MINIMUM INDIVIDUAL - Annexure K)	-
9.2.5 (Modulus of rupture - AVERAGE - Annexure K)	-
9.2.4 (Mycological Test [for MR grade only] - Annexure J)	-
9.2.2 (Resistance to water - Annexure G, Annexure H [For MR Grade])	-
9.2.2 (Resistance to water - Annexure G, Annexure H [For BWP grade])	-
9.2.1 (Dimensional Changes caused by humidity - Delamination - Annexure F)	-
9.2.1 (Dimensional Changes caused by humidity - Change in thickness - at 40% RH - Annexure F)	-
9.2.1 (Dimensional Changes caused by humidity - Change in Thickness - at 90% RH - Annexure F)	-
9.2.1 (Dimensional Changes caused by humidity - Change in Length - at 40% RH - Annexure F)	-
9.2.1 (Dimensional Changes caused by humidity - Change in Length - at 90% RH - Annexure F)	-
9.2.1 (Dimensional Changes caused by humidity - Change in thickness - at 40% RH - Annexure F)	-
9.2.1 (Dimensional Changes caused by humidity - Change in Thickness - at 90% RH - Annexure F)	-
9.2.1 (Dimensional Changes caused by humidity - Change in Length - at 40% RH - Annexure F)	-
9.2.1 (Dimensional Changes caused by humidity - Change in Length - at 90% RH - Annexure F)	-
7.3 (Dimensional Requirements - Variation in thickness - Annexure E)	-
7.3 (Dimensional Requirements - Squareness - Annexure D)	-
7.3 (Dimensional Requirements - Edge Straightness - Annexure D)	-
7.3 (Dimensional Requirements - Thickness - Annexure E)	-
7.3 (Dimensional Requirements - Width - 8.1.4)	-
7.3 (Dimensional Requirements - Length - 8.1.4)	-
8.1.3, 6.3.3, IS 1328 (Visual Inspection - Permissible Defects - IS 1328 [test method for DECORATIVE type])	-
8.1.3, 6.3.3, IS 303 (Visual Inspection - Permissible Defects - IS 303 [test method for COMMERCIAL type])	-
9.2.6 (Spot test - Annexure L)	-
8.1.3, 6.3.3, IS 1328 (Visual Inspection - Permissible Defects - IS 1328 [test method for DECORATIVE type])	-
8.1.3, 6.3.3, IS 303 (Visual Inspection - Permissible Defects - IS 303 [test method for COMMERCIAL type])	-
9.2.6 (Spot test - Annexure L)	-
9.2.3 (Adhesion of Plies - Annexure H)	-
9.2.1 (Dimensional Changes caused by humidity Change in local planeness - Annexure F)	-
9.2.6 (Spot test - Annexure L)	-
9.2.6 (mechanical) (Spot test - Annexure L)	-
Cl-9.2.7 (Amendment No-3) (Formaldehyde Content Test)	-

-
Test facility is complete except Steady State Formaldehyde Emission Test (optional Test) (Cl. 9.2.8)

15478

BIS, Southern Regional Laboratory (SRL)

None

IS 13334 : Part 2 (2014)

Skimmed milk powder - Specification: Part 2 extra grade (First Revision)

EXTRA GRADE

10430/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Table 1 (ix) (Bacterial count (IS 5402))	-
Table 1 (x) (Coliform count (IS 5401 - Part 1))	-
Table 1 (xi) (Escherichia coli (IS 5887 - Part 1))	-
Table 1 (xii) (Coagulase positive Staphylococcus aureus (IS 5887 - Part 2))	-
Table 1 (xiii) (Salmonella (IS 5887 - Part 3))	-
Table 1 (xiv)(a) (Spore Count: a)Aerobic (Bacillus cereus) Type m (IS 5887 - Part 6))	-
Table 1 (xiv)(b) (Spore Count: b) Anaerobic (Sulfite reducing Clostridia) Type m (ISO 15213 : 2003))	-
Table 1 (xiv)(b) (Spore Count: b) Anaerobic (Sulfite reducing Clostridia) Type M (ISO 15213 : 2003))	-
Table 1 (xv) (Listeria monocytogenes (IS 14988 - Part 2 : 2001))	-
Table 1 (i) (Moisture (IS 116231or 16072))	-
Table 1 (ii) (Milk protein in milk solids not fat (IS 72192))	-
Table 1 (iii) (Milk fat (IS 117213) or Annex B)	-
Table 1 (iv) (Insolubility index (IS 12759))	-
Table 1 (v) (Total ash (on dry basis), Annex B of IS 14433)	-
Table 1 (vi) (Titratable acidity (IS 11766))	-
Table 1 (viii) (Scorched particles (equivalent to Disc B) (IS 13500))	-

-
2X500g Excluding Except Lactate Content

15479

BIS, Northern Regional Laboratory (NRL)

None

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

3200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 18 (Weight)	-
Cl 15 (Length, Width & Thickness)	-
Cl 11.3 (Press)	-
Cl 10.3 (UTM)	-
Cl 7 (Workmanship)	-
Cl 7 (Workmanship)	-
Cl 7 (Workmanship)	-
Clause - 5, 8.1 & 8.2 (E250, CARBON)	-
Clause - 5, 8.1 & 8.2 (E250, SULPHUR)	-
Clause - 5, 8.1 & 8.2 (E250, SILICON)	-
Clause - 5, 8.1 & 8.2 (E250 ,MANGANESE)	-
Clause - 5, 8.1 & 8.2 (E250, PHOSPHURS)	-
Clause - 5, 8.1 & 8.2 (E250, NITROGEN)	-
Clause - 5, 8.1 & 8.2 (E250, CARBON +EQUIVELENT )	-
Clause - 5, 8.1 & 8.2 (E275, CARBON +EQUIVELENT )	-
Clause - 5, 8.1 & 8.2 (E300, CARBON +EQUIVELENT )	-
Clause - 5, 8.1 & 8.2 (E350, CARBON +EQUIVELENT )	-
Clause - 5, 8.1 & 8.2 (E410, CARBON +EQUIVELENT )	-
Clause - 5, 8.1 & 8.2 (E450, CARBON +EQUIVELENT )	-
Clause - 5, 8.1 & 8.2 (E550, CARBON +EQUIVELENT )	-
Clause - 5, 8.1 & 8.2 (E600, CARBON +EQUIVELENT )	-
Clause - 5, 8.1 & 8.2 (E250, CARBON +EQUIVELENT )	-
Clause - 5, 8.1 & 8.2 (E410, NITROGEN)	-
Clause - 5, 8.1 & 8.2 (E410, SILICON)	-
Clause - 5, 8.1 & 8.2 (E450 ,MANGANESE)	-
Clause - 5, 8.1 & 8.2 (E410, PHOSPHURS)	-
Clause - 5, 8.1 & 8.2 (E410, SULPHUR)	-
Clause - 5, 8.1 & 8.2 (E410, CARBON)	-
Clause - 5, 8.1 & 8.2 (E410, CARBON +EQUIVELENT )	-
Cl. 15 (Cl. 15 Square Bar: Out of Square)	-
Cl. 15 (Cl. 15 Square Bar: Side Width: Minimum)	-
Cl. 15 (Cl. 15 Square Bar: Side Width: Maximum)	-
Cl. 15, 16 (Thickness )	-
Cl. 15, 16 (Toe Radius R2)	-
15 (Radius R1)	-
Cl. 15, 16 (Leg Length Difference (Angle))	-
Cl. 15, 16 (Leg Length B (Angle))	-
Cl. 15, 16 (Leg Length A (Angle))	-
Cl. 15, 16 (Camber (Angle))	-
Cl 13 (Y Groove Cracking Test)	-
Clause 12 (Impact Test)	-
Cl. 15, 16 (Flange Slope)	-
Cl. 15, 16 (Web Thickness)	-
Cl. 15, 16 (Flange Thickness)	-
Cl. 15, 16 (Out of Square (Flat))	-
Cl. 15, 16 (Width )	-
Cl. 15, 16 (Thickness )	-
10 (Tensile Strength-IS:1608(P1)-22)	-
10 (Yield Stress-IS:1608(P1)-22)	-
10 (Elongation on SoA 5.65mm GL)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-

-
-

15480

BIS, Eastern Regional Laboratory (ERL)

None

IS 398 : Part 4 (1994)

Aluminium conductors for overhead transmission purposes: Part 4 aluminium alloy stranded conductors (Aluminium - Magnesium - Silicon Type) - Specification (Third Revision)

Complete facility available upto 100 sq mm only

Please see remarks View breakup
For stranded conductors with 7 strands- Rs.1500 For stranded conductors with 19 strands- Rs.3600 For stranded conductors with 37 strands- Rs. 6750 For stranded conductors with 61 strands- Rs. 10650

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 (Freedom from Defects)	-
7.2.2 Table-2, Table-4 (Calculated resistance of Stranded Conductor)	-
8.1 (Joints in wires-Conductors Containing Seven Wires)	-
8.2 (Joints in wires-Conductors Containing More Than Seven Wires)	-
9.2 Table 3 (Lay Ratio of stranded conductors)	-
9.3 (Direction of Lay)	-
9.4 (Multiple layers of wires)	-
12.2 Table 1 (Breaking Load Test- Before Stranding)	-
12.2 Table 1 (Breaking Load Test- After Stranding)	-
12.3 Table 1 (Elongation Test- Before Stranding)	-
12.3 Table 1 (Elongation Test- After Stranding)	-
12.4 Table 1 (Resistance of Aluminium wire)	-
11 (Packing and Marking)	-
7.1 Table-1 (Dimensional measurement of wires)	-
9.1 (Stranding)	-

-
Elec-Complete facility available upto 100 sq mm only. For Above 100 sq.mm. facility not available for Stress-Strain Test, Surface Condition, Ultimate B/L on stranded conductor.

Bureau of Indian Standards

The National Standards Body of India

Search by IS Number