BIS - LIMS (Laboratory Information Management System)

BIS, Southern Regional Laboratory (SRL)

IV CROSS ROAD, CIT CAMPUS, TARAMANI, CHENNAI-600113, TAMILNADU, CHENNAI, Chennai, Tamil Nadu, 600113

- srol@bis.gov.in

Scope List

Reset

262 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

181

IS 9294 (1979)

Cold-Rolled Stainless Steel Strips for Razor Blades

1725/ View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1 (Freedom from defects )	-
9.1 (Edge condition )	-
10.1 (Dimensions, mm )	-
10.2.1 (Camber -The transverse variation of thickness )	-
10.2.2 (Edge camber )	-
10.2.3 (Edge Ripple )	-
10.2.4 (Finish)	-

-
" 1.5 m Excluding except hardness test and chemical tests

182

IS 2556 : Part 15 (2004)

Vitreous sanitary appliances (Vitreous China) - Specification: Part 15 specific requirements of universal water closets

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 3 - General Requirements ( Ref. Cl.5.2 of IS 2556 (Part 1) : 1994) (Lead or a lead compound, Annex - A of IS 2556 (Part 1) : 1994))	-
Cl. 3 - General Requirements ( Ref. Cl.9.6 of IS 2556 (Part 1) : 1994) (Resistance to staining and burning, Annex - C of IS 2556 (Part 1) : 1994))	-
3 (General requirements-Application of Glazing-IS 2556 (Part 1))	-
3 (General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-General-Wavy finiah-IS 2556 (Part 1))	-
3 (General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Visible surfaces other than above-Polishing mark -IS 2556 (Part 1))	-
3 (General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-General-Wavy finiah-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Service space top of slab inside of bowl, front of fascis-Spots, blisters and pinholes-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Face of intrnal, back and side-Spots, blisters and pinholes-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-General-Warpage-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-General-Dislocations-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-wavy finish-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-Spot, blisters and pinholes-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-Bubbles and specks-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-Polishing marks-IS 2556 (Part 1)))	-
3 (General requirements-Thickness IS 2556 (Part 1))	-
3 (General requirements-PERFORMANCE REQUIllEMENTS-WARPAGE IS 2556 (Part 1))	-
8.4 (FLUSHING TESTS-Water Holding Capacity )	-
8.5.1 (FLUSHING TESTS-Single Ball Test)	-
8.5.2 (FLUSHING TESTS-Fifty Ball Test)	-
8.6 (FLUSHING TESTS-Saw Dust Test)	-
8.7 (FLUSHING TESTS-Splash Test )	-
6.1 (CONSTRUCTION)	-
4 (SIZES)	-
5.1-table 1 (DIMENSIONS AND TOLERANCES-L)	-
5.1-table 1 (DIMENSIONS AND TOLERANCES-W)	-
5.1-table 1 (DIMENSIONS AND TOLERANCES-H)	-
5.1-table 1 (DIMENSIONS AND TOLERANCES-W1)	-
5.1-table 1 (DIMENSIONS AND TOLERANCES-L2)	-
5.1-table 1 (DIMENSIONS AND TOLERANCES-L1)	-
5.1-table 1 (DIMENSIONS AND TOLERANCES-L3)	-
5.1-table 1 (DIMENSIONS AND TOLERANCES-T)	-
5.1-table 1 (DIMENSIONS AND TOLERANCES-D)	-
5.1-Table 2 (DIMENSIONS AND TOLERANCES-Connecting Dimensions-h1)	-
5.1-Table 2 (DIMENSIONS AND TOLERANCES-Connecting Dimensions-h2)	-
5.1-Table 2 (DIMENSIONS AND TOLERANCES-Connecting Dimensions-h3)	-
5.1-Table 2 (DIMENSIONS AND TOLERANCES-Connecting Dimensions-d1)	-
5.1-Table 2 (DIMENSIONS AND TOLERANCES-Connecting Dimensions-d2)	-
5.1-Table 2 (DIMENSIONS AND TOLERANCES-Connecting Dimensions-d3)	-
5.1-Table 2 (DIMENSIONS AND TOLERANCES-Connecting Dimensions-A)	-
5.1-Table 2 (DIMENSIONS AND TOLERANCES-Connecting Dimensions-B)	-
5.1-Table 2 (DIMENSIONS AND TOLERANCES-Connecting Dimensions-d4)	-
5.1-Table 2 (DIMENSIONS AND TOLERANCES-Connecting Dimensions-d5/2)	-
5.1-Table 2 (DIMENSIONS AND TOLERANCES-Connecting Dimensions-n)	-
5.1-Table 2 (DIMENSIONS AND TOLERANCES-Connecting Dimensions-M)	-
6.1 (CONSTRUCTION-closet)	-
6.1 (CONSTRUCTION-closet)	-
6.3-Table 3 (CONSTRUCTION-Dimensions of Two Piece Bend-d1)	-
6.3-Table 3 (CONSTRUCTION-Dimensions of Two Piece Bend-d2)	-
6.3-Table 3 (CONSTRUCTION-Dimensions of Two Piece Bend-d6)	-
6.3-Table 3 (CONSTRUCTION-Dimensions of Two Piece Bend-f)	-
6.3-Table 3 (CONSTRUCTION-Dimensions of Two Piece Bend-h)	-
7 (FINISH)	-
8.2 (FLUSHING TESTS-Toilet Paper)	-
3 (General requirements-PERFORMANCE REQUIllEMENTS-CRAZING IS 2556 (Part 1))	-

-
2 NOS

183

IS 204 : Part 1 (1991)

Tower bolts - Specification: Part 1 ferrous metals (Fifth Revision)

Rs.2100.00. View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (General)	-
5.2.1 Table 1 (Particulars-Barrel Tower Bolts)	-
5.2.2 Table 2 (Particulars-Sami Barrel Tower Bolts)	-
5.2.3 Table 3 (Particulars-Riveted or Spot Welded Tower Bolts)	-
5.2.4 Table 4 (Particulars-Skeleton Tower Bolts)	-
6.1- Table 1 (Dimension of Barrel tower bolts-Minimum No. of equally Spaced Screw holes in Barrel and Socket for wood screw no 6)	-
6.2- Table 2 (Dimension of Sami Barrel Tower Bolts-Minimum No. of equally Spaced Screw holes in Bolt Plate and Socket for wood screw no 6)	-
6.3- Table 3 (Dimension of Riveted or Spot Welded Tower Bolts-Minimum No. of equally Spaced Screw holes in Bolt Plate and Socket for wood screw no 6)	-
6.4- Table 4 (Dimension of Skeleton Tower Bolts- Nos of Staples)	-
6.4- Table 4 (Dimension of Skeleton Tower Bolts-Minimum No. of Screw holes for wood screw no 6)	-
8.1 (MARKING- .)	-
9 (PACKING)	-
6.1- Table 1 (Dimension of Barrel tower bolts-1.Size 2.Length of Bolt-A 3.Length of Barrel-B 4.Width of Barrel-C 5.Dia of Bolt-D 6.Length of Socket-E 7.Thickness of mild steel sheet for barrel-F 8.Dia of bore of barrel or socket- G )	-
6.2- Table 2 (Dimension of Sami Barrel Tower Bolts 1.Size 2.Length of Bolt-A 3.Length of Bolt Plate-B 4.Width of Bolt Plate-C 5.Dia of Bolt-D 6.Length of Socket-E 7.Thickness of Bolt Plate or Socket-F 8.Dia of bore of Bolt Plate or socket G )	-
6.3- Table 3 (Dimension of Riveted or Spot Welded Tower Bolts- 1.Size 2.Length of Bolt-A 3.Length of Bolt Plate-B 4.Width of Bolt Plate-C 5.Dia of Bolt-D 6.Length of Socket-E 7. Length of Strap-E" 8.Thickness of Back Plate -F 9.Thickness of Socket or Upper Plate and Strap- F" 10.Dia of bore of Bolt Plate or socket- G 11. Length of Alternative Socket-H )	-
6.4- Table 4 (Dimension of Skeleton Tower Bolts 1.Size 2.Length of Bolt-A 3.Length of Bolt Plate-B 4.Width of Bolt Plate-C 5.Dia of Bolt-D 6.Length of Staple-E 7.Thickness of Plate or Staple -F 8.Dia of bore of Plate or Staple-G 9.Dia of shank of Knob-J)	-

-
" 3x2 pcs . Excluding Excl chemical tests

184

IS 1879 (2010)

Malleable cast iron pipe fittings - Specification (Third Revision)

Rs.7800.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1.1 (Type of Fittings - IS 1879)	-
5.1.2 (Size designation - IS 1879)	-
5.1.2.1 (Equal fitting - IS 1879)	-
5.1.2.2 (Unequal fitting -IS 1879)	-
5.1.3 (Right and Left hand thread - IS 1879)	-
5.1.1 (Code Number -IS 1879)	-
6.1 (Tensile Strength - IS 14329)	-
10.ii) (Uniformity of Galvanized coating-IS 2633)	-
10.i) (Mass of Galvanized coating)	-
10.iii) (Adhesion of Galvanized coating IS 2629)	-

-
" 3 pcs+1 test bar+50g Excluding excl thread checking and pressure test

185

IS 2556 : Part 4 (2004)

Vitreous sanitary appliances (Vitreous China) - specification: Part 4 specific requirements of wash basins

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 3 and Clause 5.2 of IS 2556(Part 1) (Lead solubility test)	-
Clause 3 and Clause 9.6 of IS 2556(Part 1) (Resistance to staining and burning)	-
3 (General requirements-Application of Glazing-IS 2556 (Part 1))	-
3 (General requirements-Application of Glazing-IS 2556 (Part 1))	-
3 (General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-General-Wavy finiah-IS 2556 (Part 1))	-
3 (General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Flushing surface and horizontal face of WC pans,iDI lurfaco and horizontal tace of rima of we pans, Squatting pans bidets and urinals-Bubbles and specks-IS 2556 (Part 1))	-
3 (General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-General-Wavy finiah-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-General-Warpages-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-General-Dislocations-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Service space top of slab inside of bowl, front of fascis-Spots, blisters and pinholes-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Face of intrnal, back and side-Spots, blisters and pinholes-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-General-Warpage-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-General-Dislocations-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-wavy finish-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-Spot, blisters and pinholes-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-Bubbles and specks-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-Polishing marks-IS 2556 (Part 1)))	-
3 (General requirements-Thickness IS 2556 (Part 1))	-
3 (General requirements-PERFORMANCE REQUIllEMENTS-WARPAGE IS 2556 (Part 1))	-
3 (General requirements-PERFORMANCE REQUIllEMENTS-CRAZING IS 2556 (Part 1))	-
4 (PAITERNS)	-
4 (SIZE)	-
5.1-Table 2 (DIMENSIONS AND TOLERANCES-Functional Dimensions-A)	-
5.1-Table 2 (DIMENSIONS AND TOLERANCES-Functional Dimensions-B)	-
5.1-Table 2 (DIMENSIONS AND TOLERANCES-Functional Dimensions-B)	-
5.2.1 (DIMENSIONS AND TOLERANCES-Connecting Dimensions)	-
5.2.2-Table 3 (DIMENSIONS AND TOLERANCES-Connecting Dimensions-d1)	-
5.2.2-Table 3 (DIMENSIONS AND TOLERANCES-Connecting Dimensions-d2)	-
5.2.2-Table 3 (DIMENSIONS AND TOLERANCES-Connecting Dimensions-e)	-
5.2.2-Table 3 (DIMENSIONS AND TOLERANCES-Connecting Dimensions-f1)	-
5.2.2-Table 3 (DIMENSIONS AND TOLERANCES-Connecting Dimensions-f2)	-
5.2.2-Table 3 (DIMENSIONS AND TOLERANCES-Connecting Dimensions-g1)	-
5.2.2-Table 3 (DIMENSIONS AND TOLERANCES-Connecting Dimensions-g2)	-
5.2.2-Table 3 (DIMENSIONS AND TOLERANCES-Connecting Dimensions-g3)	-
5.2.2-Table 3 (DIMENSIONS AND TOLERANCES-Connecting Dimensions-g4)	-
5.2.2-Table 3 (DIMENSIONS AND TOLERANCES-Connecting Dimensions-g4)	-
5.2.2-Table 3 (DIMENSIONS AND TOLERANCES-Connecting Dimensions-r)	-
5.2.2-Table 3 (DIMENSIONS AND TOLERANCES-Connecting Dimensions-r1)	-
5.2.2-Table 3 (DIMENSIONS AND TOLERANCES-Connecting Dimensions-s)	-
5.2.3-Table 4 (DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-d2)	-
5.2.3-Table 4 (DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-g1)	-
5.2.3-Table 4 (DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-g4)	-
5.2.3-Table 4 (DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-g4)	-
5.2.3-Table 4 (DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-r)	-
5.2.3-Table 4 (DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-r1)	-
5.2.3-Table 4 (DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-s)	-
5.2.3-Table 4 (DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-t)	-
5.2.4-Table 5 (DIMENSIONS AND TOLERANCES-Dimensions or Waste Outlet Hole-d3)	-
5.2.4-Table 5 (DIMENSIONS AND TOLERANCES-Dimensions or Waste Outlet Hole-d5)	-
5.2.4-Table 5 (DIMENSIONS AND TOLERANCES-Dimensions or Waste Outlet Hole-d6)	-
5.2.4-Table 5 (DIMENSIONS AND TOLERANCES-Dimensions or Waste Outlet Hole-h)	-
5.2.4-Table 5 (DIMENSIONS AND TOLERANCES-Dimensions or Waste Outlet Hole-p)	-
5.2.5-Table 6 (DIMENSIONS AND TOLERANCES-Fixing Dimensions for Wall Hung Wash Basin-n)	-
5.2.5-Table 6 (DIMENSIONS AND TOLERANCES-Fixing Dimensions for Wall Hung Wash Basin-p)	-
6.1 (CONSTRUCTION)	-
6.1.1 (CONSTRUCTION)	-
6.2 (CONSTRUCTION-Tap Holes)	-
6.2 (CONSTRUCTION-Tap Holes)	-
6.3-Table 5 (CONSTRUCTION-Waste Hole)	-
6.3 (CONSTRUCTION-Waste Hole-Flange dia west fitting)	-
6.4.1 (CONSTRUCTION-Fixing Arrangements-Bracket Stud)	-
6.4.1 (CONSTRUCTION-Fixing Arrangements-Bracket Stud-Horizontal distance between two stud)	-
6.4.2 (CONSTRUCTION-Fixing Arrangements-Screw Fixing-Holes)	-
6.4.2 (CONSTRUCTION-Fixing Arrangements-Screw Fixing-Hole dia)	-
6.4.3 (CONSTRUCTION-Fixing Arrangements-Rag Bolt)	-
6.5 (CONSTRUCTION-Overflow-horizontal dimension )	-
6.5 (CONSTRUCTION-Overflow-Area)	-
6.6 (CONSTRUCTION-Soap Recess(es))	-
6.8 (CONSTRUCTION-Chain Stay Hole-Dia)	-
6.9 (CONSTRUCTION-Pedestal)	-
6.9 (CONSTRUCTION-Pedestal)	-
6.9 (CONSTRUCTION-Pedestal-The height from the floor to top of the rim of basin)	-
7 (FINISH)	-

-
2 NOS

186

IS 2556 : Part 3 (2004)

Vitreous Sanitary Appliances (Vitreous China) - - Part 3: Specific Requirements of Squatting Pans

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 3 and Clause 5.2 of IS 2556(Part 1) (Lead solubility test)	-
Clause 3 and Clause 9.6 of IS 2556(Part 1) (Resistance to staining and burning)	-
3 (General requirements-Application of Glazing-IS 2556 (Part 1))	-
3 (General requirements-Application of Glazing-IS 2556 (Part 1))	-
3 (General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-General-Wavy finiah-IS 2556 (Part 1))	-
3 (General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-General-Discoloration-IS 2556 (Part 1))	-
3 (General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Visible surfaces other than above-Polishing mark -IS 2556 (Part 1))	-
3 (General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-General-Wavy finiah-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-General-Dislocations-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Service space top of slab inside of bowl, front of fascis-Spots, blisters and pinholes-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Face of intrnal, back and side-Spots, blisters and pinholes-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Face of intrnal, back and side-Polishing marks-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-General-Warpage-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-General-Dislocations-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-wavy finish-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-Spot, blisters and pinholes-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-Bubbles and specks-IS 2556 (Part 1)))	-
3 (General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-Polishing marks-IS 2556 (Part 1)))	-
3 (General requirements-Thickness IS 2556 (Part 1))	-
3 (General requirements-PERFORMANCE REQUIllEMENTS-WARPAGE IS 2556 (Part 1))	-
3 (General requirements-PERFORMANCE REQUIllEMENTS-CRAZING IS 2556 (Part 1))	-
4 (PATTERNS )	-
4 (SIZE)	-
5.1 (CONSTRUCTION)	-
5.1.1 (CONSTRUCTION)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-A)	-
6.1-Table 1 (DIMENSIONS AND TOLERANCES-B)	-
6.1-Table 2 (DIMENSIONS AND TOLERANCES-F)	-
6.1-Table 3 (DIMENSIONS AND TOLERANCES-H)	-
6.1-Table 4 (DIMENSIONS AND TOLERANCES-J)	-
6.1-Table 5 (DIMENSIONS AND TOLERANCES-Slope of bottom of pan)	-
6.1-Table 6 (DIMENSIONS AND TOLERANCES-L)	-
6.1-Table 7 (DIMENSIONS AND TOLERANCES-N)	-
6.1-Table 8 (DIMENSIONS AND TOLERANCES-P)	-
6.2-Table 2 (DIMENSIONS AND TOLERANCES-C)	-
6.2-Table 3 (DIMENSIONS AND TOLERANCES-D)	-
6.2-Table 4 (DIMENSIONS AND TOLERANCES-E)	-
6.2-Table 5 (DIMENSIONS AND TOLERANCES-G)	-
6.2-Table 6 (DIMENSIONS AND TOLERANCES-K)	-
6.2-Table 7 (DIMENSIONS AND TOLERANCES-M)	-
6.2 (DIMENSIONS AND TOLERANCES-top surface variation)	-
7 (FINLSH)	-
8.1 (FLUSHING TESTS-Toilet Paper Test)	-
8.3 (FLUSHING TESTS-Water Holding Capacity Test)	-
8.4 (FLUSHING TESTS-Saw Dust Test)	-
8.5 (FLUSHING TESTS-Splash Test)	-

-
2 NOS

187

IS 8794 (1988)

Specification for cast iron detachable joints for use with asbestos cement pressure pipes (First Revision)

3900/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1, Table 2 (External Dia of AC Pipe(D2))	-
6.1, Table 2 (Inside diaFlange(DI))	-
6.1, Table 2 (External Dia at Centre(DEC))	-
6.1, Table 2 (Collar Width(Wc))	-
6.1, Table 2 (Thickness(t))	-
6.1, Table 3 (Nominal Dia of Bolt(do))	-
6.1, Table 3 (Minimum prefared length of bolt(L))	-
6.1, Table 4 (Mass of joints)	-

-
" one set " Excluding "Excl hydrostatic test. Facility for preparation of test specimen not available"

188

IS 9295 (1983)

Specification for steel tubes for idlers for belt conveyors (First Revision)

Rs 5100/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8.1.1 Table 1 (Tensile Strength- IS 1608(1))	-
8.1.1 Table 1 (Yield Strength- IS 1608)	-
8.1.1 Table 1 (Elongation Percent- IS 1608)	-
8.3 (Flattening Test- IS 2328)	-
9.1 Table 2 (Outside Diameter)	-
9.1 Table 2 (Thickness)	-
9.1 Table 2 (Mass)	-
13.1.1 (Ovality)	-
13.1.2 (Eccentricity)	-
16.1 (Length)	-
7.1 (Sulphur- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
7.1 (Phosphorous- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-

-
" 2 mt + 25g " Chemical Facility is available Quantity: 5 Pieces of 5cm X 5cm Excluding excl drift test for >150mm NB. Facility for preparation of test specimen not available.

189

IS 11657 (1986)

Specification for phosphorus oxychloride, technical

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.1 (Description )	-
2.2, Table 1 and A-3 of IS 11657 (Relative density at 27°C)	-
2.2, Table 1 and A-4 of IS 11657 (Assay ( as POCl3 ))	-

-
" 500 ml Excluding except boiling range

190

IS 11744 (1986)

PecificatiOn for phosphorous pentachloride, technical

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl no . 2.1 (Description)	-
Cl no . 2.2 APPENDIX A -2 [Table 1 Sl no. (i)] (Phosphorous pentachloride ( as PCl 5),)	-

-
" 100 g Excluding except bulk density

191

IS 12330 (1988)

Specificatioon for sulphate resisting Portland cement

Rs.12900/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 - Table - 1 i (Ratio of percentage of lime to percentages of silica, alumina and iron oxide - Cl 4 of IS 4032:1985)	-
4.1 - Table - 1 ii (Insoluble residue - Cl 4.10 of IS 4032:1985)	-
4.1 - Table - 1 iii (Magnesia - Cl 4.8 of IS 4032:1985)	-
4.1 - Table - 1 iv (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-
4.1 - Table - 1 v (Tricalcium aluminate (C3A) - Cl 4 of IS 4032:1985)	-
4.1 - Table - 1 vi (Tetracalcium alumino ferrite phase plus twice the tricalcium aluminate ( C4AF + 2C3A ) - Cl 4 of IS 4032:1985)	-
4.1 - Table - 1 vii (Total loss on ignition - Cl 4.2 of IS 4032:1985)	-
5.1 (Fineness 4031 Part 2)	-
5.2.1 (Expansion by Le Chatelier- 4031 Part 3)	-
5.2.1.1 (Expansion after aeration - 4031 Part 3)	-
5.2.1 (Expansion by Autoclave- 4031 Part 3)	-
5.3 a) (Setting Time Initial- 4031 Part 5)	-
5.3 b) (Setting Time Final- 4031 Part 5)	-
5.5 i) (Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-
5.5 ii) (Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-
5.5 iii) (Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-
5.6 (Transverse Strength - IS 4031 Part 8 (Optional))	-

-
" 8 kg + 500gm Excluding cl. 5.4 sulphate expansion and transverse strength test (Optional)

192

IS 12928 (1990)

Precipitated barium carbonate for ceramic and glass industry - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl no 5.1 (Description )	-
Cl no 5.2 [ Table 1, Sl no.(i) ] Annex A-2 Grade-1 (Barium ( as Ba ))	-
Cl no 5.2 [ Table 1, Sl no.(i) ] Annex A-2 Grade-2 (Barium ( as Ba ))	-
Cl no 5.2 [ Table 1, Sl no.(ii) ] Annex A-3 Grade-1 (Volatile matter 105 ± 2°C)	-
Cl no 5.2 [ Table 1, Sl no.(ii) ] Annex A-3 Grade-2 (Volatile matter 105 ± 2°C)	-
Cl no 5.2 [ Table 1, Sl no.(iii) ] Annex A-4 Grade-1 ref to IS 12305 (Matter insoluble in hydrochloric acid)	-
Cl no 5.2 [ Table 1, Sl no.(iii) ] Annex A-4 Grade-2 ref to IS 12305 (Matter insoluble in hydrochloric acid)	-
Cl no 5.2 [ Table 1, Sl no.(iv) ] Annex A-5 Grade-2 only (Free alkali)	-
Cl no 5.2 [ Table 1, Sl no.(v) ] Annex A-6 Grade-1 (Water soluble sulphide ( as S ))	-
Cl no 5.2 [ Table 1, Sl no.(v) ] Annex A-6 Grade-2 (Water soluble sulphide ( as S ))	-
Cl no 5.2 [ Table 1, Sl no.(vi) ] Annex A-7 Grade-1 only (Sulphur ( as SO4 ))	-
Cl no 5.2 [ Table 1, Sl no.(vii) ] Annex A-8 Grade-1only (Alkali and other metal sulphates ( as BaSO4 ),)	-
Cl no 5.2 [ Table 1, Sl no.(viii) ] Annex A-9 Grade-1only (Sodium oxide ( as Na2O ))	-
Cl no 5.2 [ Table 1, Sl no.(ix) ] Annex A-10 Grade-1 & Grade-2 (Total iron ( as Fe2O3 ))	-
Cl no 5.2 [ Table 1, Sl no.(x) ] Annex A-11 Grade-1only (Tap density)	-

-
" 500 g Excluding except residue retained on 63 microns IS sieve

193

IS 14709 (1999)

N - Butyl acrylate - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl No. 3 C-5 and D-5 [ Table 1, Sl no.(ii)] Annex B (Acidity (as acrylic acid))	-
Cl No. 3 C-5 and D-5 [ Table 1, Sl no.(v)] Annex C (Inhibitors (as Butyl Etherhydroquinone))	-

-
" 250 ml " Excluding except assay of n-butyl acrylate, colour, water content

194

IS 14735 (1999)

Unplasticized Polyvinyl Chloride (UPVC) Injection Moulded Fittings for Soil and Waste Discharge System for Inside and Outside Buildings Including Ventilation and Rain Water System -

Total Testing Charges : Rs. 9970.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.15, Annex B (Sulphated Ash Content)	-
19 (Marking)	-
3 (Type of Fitting)	-
4 (Size Designation)	-
5 (Colour of fittings)	-
7.1,Table 1 (Wall thickness)	-
7.2 ,Table 2&3 (Socket Dimensions)	-
7.3 (Dimensions of waste trap(Nahani Trap)	-
10 (Workmanship)	-
11 (Design requirements)	-
11.1 (Solvent cement type or Rubber ring type)	-
11.2 (Socket and spigot configeration)	-
11.4,Table 5 (Vent cowl)	-
11.5,Table 6 (Pipe Clips)	-
12.1 (Visual appearance)	-
12.2 (Stress relief test)	-
12.3 (Vicat softening tempewrature)	-
16.1 (Impact test)	-
17 (Watet tightness of joint)	-
16.1 (Impact test)	-

-
Excluding excl resistance to sulphuric acid, titanium dioxide, Hydrostatic test above 110mm. Pipes shall be supplied for hydrostatic testing.

195

IS 1489 : Part 2 (2015)

Portland - Pozzolana cement - Specification: Part 2 calcined clay based

Rs.8420/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 - Table - 1 i (Insoluble residue - Cl 7.4 of IS 4032:1985)	-
6 - Table - 1 ii (Magnesia - Cl 7.2 of IS 4032:1985)	-
6 - Table - 1 iii (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-
6 - Table - 1 iv (Loss on ignition - Cl 7.1 of IS 4032:1985)	-
6 - Table - 1 v (Chloride content - Cl 4.13 of IS 4032:1985)	-
7 -Table 2- i (Fineness 4031 Part 2)	-
7 -Table 2- ii- a (Expansion by Le Chatelier- 4031 Part 3)	-
7 -Table 2- ii- b (Expansion by Autoclave- 4031 Part 3)	-
7 -Table 2- iii- a (Setting Time Initial- 4031 Part 5)	-
7 -Table 2-iii- b (Setting Time Final- 4031 Part 5)	-
7 -Table 2- iv- a (Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-
7 -Table 2- iv- b (Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-
7 -Table 2- iv- c (Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-
7 -Table 2- vi (Drying Shrinkage- IS 4031 Part 10)	-
7 -Table 2- vi (Drying Shrinkage- IS 4031 Part 10)	-
7 -Table 2- vi (Drying Shrinkage- IS 4031 Part 10)	-

-
" 8 Kg for Mechanical + Chemical 500 g " Excluding Complete other than Transverse Strength (Optional)

196

IS 15030 (2001)

Terephthalic acid - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl No 3.1 (Description)	-
Cl No 3.2 [ Table 1, Sl no.(iii) ] Annex C (Ash content,)	-
Cl No 3.2 [ Table 1, Sl no.(iv) ] Annex D (Acid value)	-
Cl No 3.2 [ Table 1, Sl no.(v) ] Annex E & Annex J (Total of iron, cobalt, manganese and chromium)	-
Cl No 3.2 [ Table 1, Sl no.(v) ] Annex E & Annex J (iron)	-
Cl No 3.2 [ Table 1, Sl no.(v) ] Annex E & Annex J (cobalt)	-
Cl No 3.2 [ Table 1, Sl no.(v) ] Annex E & Annex J (manganese )	-
Cl No 3.2 [ Table 1, Sl no.(v) ] Annex E & Annex J (chromium)	-
Cl No 3.2 [ Table 1, Sl no.(vi) ] Annex F & Annex J (Total of sodium, magnesium, potassium, calcium and Nickel)	-
Cl No 3.2 [ Table 1, Sl no.(vi) ] Annex F & Annex J (Sodium)	-
Cl No 3.2 [ Table 1, Sl no.(vi) ] Annex F & Annex J (magnesium)	-
Cl No 3.2 [ Table 1, Sl no.(vi) ] Annex F & Annex J (potassium)	-
Cl No 3.2 [ Table 1, Sl no.(vi) ] Annex F & Annex J (calcium)	-
Cl No 3.2 [ Table 1, Sl no.(vi) ] Annex F & Annex J (nickel)	-

-
" 500 g x 2 Excluding TF for acid value only is available

197

IS 1507 (1977)

Specification for copper oxychloride water dispersible powder concentrates

Rs 2700/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.2.1 (Description)	-
2.3 Table 1 (i) (Copper content, )	-
2.3 Table 1 (ii) (Suspensibility, )	-
2.3 Table 1 (iii) (pH )	-

-
" 500 g

198

IS 170 (2020)

Acetone — Specification ( Fifth Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl No 3.1 ( Description)	-
Cl No 3.2 (Miscibility with Water)	-
Cl 3.3 and 6.1 [ Table 1, Sl No. (vi) ] ref to 8 of IS 82 (Residue on evaporation)	-
Cl 3.3 and 6.1 ANNEX C [ Table 1, Sl No. (vii) ] (Acidity (as CH3COOH),)	-
Cl 3.3 and 6.1 ANNEX D [ Table 1, Sl No. (viii) ] (Alkalinity)	-
Cl 3.3 and 6.1 ANNEX E [ Table 1, Sl No. (ix) ] (Permanganate test)	-
Cl 3.3 and 6.1 ANNEX F [ Table 1, Sl No. (x) ] (Alcoholic impurities)	-

-
" 500 ml x 2 Excluding except purity of acetone, water content, colour, distillation range, benzene content, methanol content

199

IS 253 (2014)

Specification for common salt (Fourth Revision)

6690 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause -3 for common salt 3.1 ( 3.1.1 ) ( The material shall be crystalline solid, white or pale pink or light grey in colour.)	-
Clause -3 for common salt 3.1 ( 3.1.2 ) Annex-2 (Moisture The material shall contain not more than 6.0 percent by mass of moisture, on as received basis, when tested according to the method given in A-2)	-
Clause-3.2 for dairy salt (3.2.1) (The material shall be crystalline white solid and free from any visible impurities.)	-
Clause-3.2 for dairy salt (3.2.3) Annex -2 (3.2.3 Moisture The material shall contain not more than 0.5 percent by mass of moisture, on as received basis, when tested according to the methods given in A-2.)	-
Table 1 (i) Annex -4 (Water insoluble matter, common)	-
Table 1 (i) Annex -4 (Water insoluble matter, Dairy)	-
Table 1 (ii) Annex-5 (Chloride content (as NaCl)common)	-
Table 1 (ii) Annex-5 (Chloride content (as NaCl), Dairy)	-
Table 1 (iii) Annex-6 ( Matter soluble in water, other than sodium chloride, common)	-
Table 1 (iii) Annex-6 ( Matter soluble in water, other than sodium chloride, Dairy)	-
Table 1 (iv) (Calcium (as Ca), water soluble, percent by mass, common)	-
Table 1 (iv) Annex-7 (Calcium (as Ca), water soluble, percent by mass, Dairy)	-
Table 1 (v) (Magnesium (as Mg), water soluble, percent by mass, common )	-
Table 1 (v) Annex-7 (Magnesium (as Mg), water soluble, percent by mass, Dairy )	-
Table 1 (vi) (Sulphate as SO2 percent by mass, common)	-
Table 1 (vi) Annex-8 (sulphate as SO2 percent by mass, Dairy)	-
Table 1 (vii) Annex-9 (Alkalinity (as Na2CO3), common)	-
Table 1 (vii) Annex-11 (Alkalinity (as Na2CO3), Dairy)	-
Table 1 (viii) (Lead (as Pb), common)	-
Table 1 (viii) (Lead (as Pb),Dairy )	-
Table 1 (ix) (Iron (as Fe), common)	-
Table 1 (ix) (Iron (as Fe), Dairy)	-
Table 1 (x) Annex-11 (x) Arsenic (as As), common)	-
Table 1 (x) Annex-11 (x) Arsenic (as As),Dairy)	-
Table 1 (xi) Annex-12 (Copper (as Cu), common)	-
Table 1 (xi) Annex-12 (Copper (as Cu), Dairy )	-

-
" 500 g

200

IS 4148 (1989)

Surgical rubber gloves - Specification (First Revision)

Rs. 3925/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.5 (pH of Aqueous Extract )	-
4.2 (Dimensions Fig 1 and Table 1)	-
4.2 (Dimensions Fig 1 and Table 1)	-
4.1.1 (Manufacture)	-
4.1.2 (Manufacture)	-
4.1.3 (Manufacture)	-
4.1.4 (Manufacture)	-
4.3 (Thickness)	-
4.4.1 (Physical Properties)	-
4.4.1 (Physical Properties)	-
4.4.2 (After accelerated aging at 70 + 1OC for 240 h )	-
4.4.2 (After accelerated aging at 70 + 1OC for 240 h )	-
4.4.2 (After accelerated aging at 70 + 1OC for 240 h )	-
4.4.3 (After heat ageing in autoclave)	-
4.2 (Dimensions Fig 1 and Table 1)	-
4.2 (Dimensions Fig 1 and Table 1)	-
4.2 (Dimensions Fig 1 and Table 1)	-
4.2 (Dimensions Fig 1 and Table 1)	-
4.2 (Dimensions Fig 1 and Table 1)	-
4.4.4 (Tension Set)	-

-
" 20 Pairs

201

IS 4581 (1978)

Specification for phosphorus trichloride, pure and analytical reagent (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (Description )	-
3.2, Table 1 and A-2 of IS 4581 (Phosphprus Tricloride ( as PCl3 ) - For Analytical Reagent )	-
3.2, Table 1 and A-2 of IS 4581 (Phosphprus Tricloride ( as PCl3 ) - For Pure grade)	-
3.2, Table 1 and A-5 of IS 4581 (Sulphate ( as SO4) - For Analytical Reagent)	-
3.2, Table 1 and A-7 of IS 4581 (Iron ( as Fe ) - For Analytical Reagent)	-

-
" 500 ml " Excluding except boiling range, residue on evaporation for all grades; heavy metals for grade 1

202

IS 5295 (1985)

Specification for ethylene glycol (First Revision)

Rs. 1500 Fibre Grade View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl No. 3.1 (Description)	-
Cl No. 3.2 [ Table 1, Sl no.(i) ] Appendix A-2 FibreGrade only (Colour)	-
Cl No. 3.2 [ Table 1, Sl no.(ii) ] Appendix A-2 FibreGrade only (Colour after boiling for 4 hour under total reflux)	-
Cl No. 3.2 [ Table 1, Sl no.(vi) ] Appendix A-6 General Grade & Fibre Grade (Acidity ( as acetic acid))	-
Cl No. 3.2 [ Table 1, Sl no.(vii) ] Appendix A- 7 General Grade & Fibre Grade (Ash)	-
Cl No. 3.2 [ Table 1, Sl no.(x) ] Appendix A-10 Fibre Grade only (Iron Content )	-
Cl No. 3.2 [ Table 1, Sl no.(xi) ] Appendix A-11 Fibre Grade only (Chlorides content ( as Cl ))	-

-
" 500 g x 2 Excluding except distillation range, moisture content, freezing point for General grade; except diethylene glycol content, relative density, colour, colour after boiling, uv transmitance, distillation range, moisture content for Fibre grade

203

IS 6100 (1984)

Specification for sodium tripolyphosphate, anhydrous, technical (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.1 (Description)	-
2.3, Table 1 and Appendix B-2 of IS 6100 (Moisture)	-
2.3, Table 1 and Appendix B-3 of IS 6100 (Matter insoluble in water)	-
2.3, Table 1 and Appendix B-4 of IS 6100 (Phosphorus ( as P2O5 ))	-
2.3, Table 1 and Appendix B-5 of IS 6100 (pH value)	-

-
" 500g " Excluding except Iron, Copper, sieve analysis, fluoride, temperature rise

204

IS 650 (1991)

Standard sand for testing cement - Specification (Second Revision)

Rs 1500.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (Chemical Req)	-
Cl. 4.1 (shall be of quartz, light grey or whitish variety and shall be free from silt. The sand grains shall be angular, the shape of the grains approximating to the spherical form; elongated and flattened grains being present only in very small or negligible quantities)	-
Cl. 4.2 (Sieve test and particle size distribution)	-

-
-

205

IS 797 (1982)

Specification for common salt for chemical industries (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.3.1 (Description)	-
Cl.3.2.1 (Moisture Content For Grade 1 material (Annex A2))	-
Cl.3.2.2 (Moisture Content For Grade 2 material (Annex A2))	-
Table 1 Cl.3.3 (Sodium Chloride (as NaCl) For Grade 1 material (Annex A3))	-
Table 1 Cl.3.3 (Sodium Chloride (as NaCl) For Grade 2 material (Annex A3))	-
Table 1 Cl.3.3 (Material insoluble in water For Grade 1 material (Annex A4))	-
Table 1 Cl.3.3 (Material insoluble in water For Grade 2 material (Annex A4))	-
Table 1 Cl.3.3 (Calcium salts (as Ca) For Grade 1 material (Annex A5))	-
Table 1 Cl.3.3 (Calcium salts (as Ca) For Grade 2 material (Annex A5))	-
Table 1 Cl.3.3 (Magnasium salts (as Mg) For Grade 1 material (Annex A5))	-
Table 1 Cl.3.3 (Magnasium salts (as Mg) For Grade 2 material (Annex A5))	-
Table 1 Cl.3.3 (Sulphates (as SO4) For Grade 1 material (Annex A6))	-
Table 1 Cl.3.3 (Sulphates (as SO4) For Grade 2 material (Annex A6))	-
Table 1 Cl.3.3 (Iron compound (as Fe) For Grade 1 material (Annex A7))	-
Table 1 Cl.3.3 (Iron compound (as Fe) For Grade 2 material (Annex A7))	-

-
" 2 x 500 g " Excluding Excl TF for Table 1 & 3.3.1

206

IS 798 (2020)

Orthophosphoric Acid — Specification ( Third Revision )

Rs.14822/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Description)	-
5.2.2 Table 1 (ii) (Orthophosphoric acid (H3 PO4 ))	-
5.2.2 Table 1 (iii) (Iron (as Fe), )	-
5.2.2 Table 1 (iv) (Chlorides (as Cl), )	-
5.2.2 Table 1 (v) (Sulphates (as SO4 ), )	-
5.2.2 Table 1 (vi) (Arsenic (as As2 O3 ), )	-
5.2.2 Table 1 (viii) (Nitrates (as NO3 ),)	-
5.2.2 Table 1 (ix) (Lead (as Pb), parts per million, Max)	-
5.2.2 Table 1 (x) (Silica (as SiO2 ), )	-
5.2.2 Table 1 (xii) (Oxygen absorbed (as O),)	-
5.2.2 Table 1 (xiv) (Manganese (as Mn), )	-
5.2.2 Table 1 (xvi) (Mercury (as Hg), )	-
5.2.2 Table 1 (xvii) (Aluminium (as Al), )	-

-
" 500 g " Excluding except Calcium, Magnesium, relative density, Volatile acid for AR Grade ; Molybdenum, relative density, Antimony for For Technical grade

207

IS 8041 (1990)

Rapid hardening portland cement - Specific4tion (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 - Table - 1 i (Ratio of percentage of lime to percentages of silica, alumina and iron oxide - Cl 4 of IS 4032:1985)	-
5.1 - Table - 1 ii (Ratio of percentage of alumina to that of iron oxide - Cl 4 of IS 4032:1985)	-
5.1 - Table - 1 iii (Insoluble residue - Cl 4.10 of IS 4032:1985)	-
5.1 - Table - 1 iv (Magnesia - Cl 4.8 of IS 4032:1985)	-
5.1 - Table - 1 v (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-
5.1 - Table - 1 vi (Total loss on ignition - Cl 4.2 of IS 4032:1985)	-
6.1 (Fineness 4031 Part 2)	-
6.2.1 (Expansion by Le Chatelier- 4031 Part 3)	-
6.2.1 (Expansion by Autoclave- 4031 Part 3)	-
6.3 a) (Setting Time Initial- 4031 Part 5)	-
6.3 b) (Setting Time Final- 4031 Part 5)	-
6.4 a) (Compressive Strength At 24 hrs ± 30 minutes - IS 4031 Part 6)	-
6.4 b) (Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-

-
" 8 kg + 500g " Excluding Except Transverse test (Optional)

208

IS 8043 (1991)

Specification for hydrophobic Portland cement

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (ref. 6 - Table - 1 i of IS 269:2015) (Ratio of percentage of lime to percentages of silica, alumina and iron oxide - Cl 4 of IS 4032:1985)	-
5.1 (ref. 6 - Table - 1 ii of IS 269:2015) (Ratio of percentage of alumina to that of iron oxide - Cl 4 of IS 4032:1985)	-
5.1 (ref. 6 - Table - 1 iii of IS 269:2015) (Insoluble residue - Cl 4.10 of IS 4032:1985)	-
5.1 (ref. 6 - Table - 1 iv of IS 269:2015) (Magnesia - Cl 4.8 of IS 4032:1985)	-
5.1 (ref. 6 - Table - 1 v of IS 269:2015) (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-
5.1 (ref. 6 - Table - 1 vi of IS 269:2015) (Loss on ignition - Cl 4.2 of IS 4032:1985)	-
5.1 (ref. 6 - Table - 1 vii of IS 269:2015) (Chloride content - Cl 4.13 of IS 4032:1985)	-
5.1 (ref. 6 - Table - 1 viii of IS 269:2015) ( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-

-
" mech - 8 kg; chem - 500 g Excluding Mech-Except transverse strength(optional), Hydrophobicity test; Chem-except Alkali content

209

IS 8229 (1986)

Specification for oil - Well cement (First Revision)

ordinary, moderate & high sulphate resistant type

5400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 - Table - 1 i (Magnesium Oxide (MgO) - Cl 4.8 of IS 4032:1985)	-
4.1 - Table - 1 ii (Sulphur Trioxide(SO3) - Cl 4.9 of IS 4032:1985)	-
4.1 - Table - 1 iii (Loss on ignition - Cl 4.2 of IS 4032:1985)	-
4.1 - Table - 1 iv (Insoluble residue - Cl 4.10 of IS 4032:1985)	-
4.1 - Table - 1 v (Tricalcium aluminate (3CaO.Al2O3) - Cl 4 of IS 4032:1985)	-
4.1 - Table - 1 x (Tricalcium Silicate (3CaO.SiO2) - Cl 4 of IS 4032:1985)	-
4.1 - Table - 1 xix (Tetracalcium aluminoferrite (4CaO.Al2O3.Fe2O3) plus twice the tricalcium aluminate (3CaO.Al2O3) - Cl 4 of IS 4032:1985)	-
4.1 - Table - 1 i (Magnesium Oxide (MgO) - Cl 4.8 of IS 4032:1985)	-
5.1 and Table 2 ii (Fineness IS : 4031:1988)	-
5.1 and Table 2 iii (Soundness, Autoclave expansion IS 4031:1988)	-

-
" mech - 8 kg; chem - 500 g Excluding Mech- except water, free water content of slurry, preparation of slurry, thickening time, compressive strength; Chem- except alkali content for Class- G & H

210

IS 9825 (2003)

Chlorine tablets - Specification (Second Revision)

Rs.4330/ View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.4.2 (Description)	-
Cl.4.3 (Size (Mass of tablet))	-
Cl.4.3 (Available Chlorine (Annex A))	-
Cl.4.4 (Moisture (Annex B))	-
Cl.4.4 (Shelf Life (Annex A))	-

-
2x500g

First
Prev
6
7
8
9
Next
Last

Bureau of Indian Standards

The National Standards Body of India

BIS, Southern Regional Laboratory (SRL)

IV CROSS ROAD, CIT CAMPUS, TARAMANI, CHENNAI-600113, TAMILNADU, CHENNAI, Chennai, Tamil Nadu, 600113

- srol@bis.gov.in

Scope List