BIS - LIMS (Laboratory Information Management System)

DELHI TEST HOUSE KUNDLI

PLOT NO 50 phase IV sector 57 hsiidc industrial area kundli, Sonipat, Sonipat, Haryana, 131028

9810442016 ag@delhitesthouse.com

Scope List

Reset

60 Results

S.No.

Indian Standard No.

Product

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 16169 (2014)

Utility - Interconnected photovoltaic inverters - Test procedure of islanding prevention measures

300000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6, (Elec)(Test for single or multi-phase inverter)	-	3500	-
Annex A(Islanding as it applies to PV systems)	-	2000	-
Annex B(Test for independent islanding device)	-	4000	-
6 to 6.2, (Elec)(Test for single or multi-phase inverter to Pass/fail criteria)	-	290000	-
7, (Elec)(Documentation)	-	500	-
Annex B, (Elec)(Test for independent islanding device)	-	4000	-
Annex A, (Elec)(Islanding as it applies to PV systems)	-	2000	-
7(Documentation)	-	500	-
6 to 6.2(Test for single or multi-phase inverter to Pass/fail criteria)	-	290000	-
6(Test for single or multi-phase inverter)	-	3500	-

Complete

23 Jun, 2025

IS 16169 (2019)

Utility - Interconnected photovoltaic inverters - Test procedure of islanding prevention measures (First Revision)

300000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Test for single or multi-phase inverter)	-	3000	-
Annex A(Islanding as it applies to PV systems)	-	2000	-
Annex B(Test for independent islanding device)	-	4000	-
6 to 6.2(Test for single or multi-phase inverter to Pass/fail criteria)	-	290000	-
7(Documentation)	-	500	-
4(Testing circuit)	-	200	-
5(Testing equipment)	-	100	-
Annex C(Gate blocking signal)	-	200	-

Complete

23 Jun, 2025

IS/IEC 61730 : PART 2 (2019)

Photovoltaic (PV) module safety qualification: Part 2 requirements for testing (First Revision)

1500000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(General)	-	5000	-
4.2(Thermal Cycling (TC50))	-	7857	-
4.2(Thermal Cycling (TC200))	-	7857	-
4.2(Humidity Freeze (HF10))	-	7857	-
4.2(Damp Heat (DH1000))	-	7857	-
4.2(UV Preconditioning)	-	7857	-
4.2(Cold Conditioning)	-	7857	-
4.2(Dry Hot Conditioning)	-	7857	-
4.3(Visual inspection)	-	11428	-
4.3(Performance at STC)	-	11428	-
4.3(Maximum power determination)	-	11428	-
4.3(Insulation thickness)	-	11428	-
4.3(Durability of markings)	-	11428	-
4.3(Sharp edge test)	-	11428	-
4.3(Bypass diode functionality test)	-	11428	-
4.4(Accessibility test)	-	2857	-
4.4(Cut susceptibility test)	-	2857	-
4.4(Continuity test for equipotential bonding)	-	2857	-
4.4(Impulse voltage test)	-	2857	-
4.4(Insulation test)	-	2857	-
4.4(Wet leakage current test)	-	2857	-
4.4(Robustness of terminations test)	-	2857	-
4.5(Temperature test)	-	1333	-
4.5(Hot-spot endurance test)	-	1333	-
4.5(Fire test)	-	1333	-
4.5(Ignitability test)	-	1333	-
4.5(Bypass diode thermal test)	-	1333	-
4.5(Reverse current overload test)	-	1333	-
4.6(Module breakage test)	-	2142	-
4.6(Screw connection test)	-	2142	-
4.6(Mechanical load test)	-	2142	-
4.6(Peel test)	-	2142	-
4.6(Lap shear strength test)	-	2142	-
4.6(Materials creep test)	-	2142	-
4.6(Robustness of terminations test)	-	2142	-
10.2 IS/IEC 61730-2( Visual inspection MST01)	-	10000	-
10.3 IS/IEC 61730-2(Performance at STC MST 02)	-	80000	-
10.4 IS/IEC 61730-2(Maximum power determination MST 03)	-	30000	-
10.5 IS/IEC 61730-2(Insulation thickness test MST 04)	-	10000	-
10.6 IS/IEC 61730-2(Durability of marking MST 05)	-	10000	-
10.7 IS/IEC 61730-2(Sharp edge test MST 06)	-	10000	-
10.8 IS/IEC 61730-2(Bypass diode functionality test MST 07)	-	10000	-
10.9 IS/IEC 61730-2(Accessibility test MST 11)	-	20000	-
10.10 IS/IEC 61730-2(Cut susceptibility test MST 12)	-	10000	-
10.11 IS/IEC 61730-2(Continuity test of equipotential bonding MST 13)	-	20000	-
10.12 IS/IEC 61730-2(Impulse voltage test MST 14)	-	20000	-
10.13 IS/IEC 61730-2( Insulation test MST 16)	-	10000	-
10.14 IS/IEC 61730-2( Wet leakage current test MST 17)	-	20000	-
10.15 IS/IEC 61730-2( Temperature test MST 21)	-	35000	-
10.16 IS/IEC 61730-2(Hot-spot endurance test MST 22)	-	35000	-
10.17 IS/IEC 61730-2( Fire test MST 23)	-	70000	-
10.18 IS/IEC 61730-2(Ignitability test MST 24)	-	15000	-
10.19 IS/IEC 61730-2( Bypass diode thermal test MST 25)	-	25000	-
10.20 IS/IEC 61730-2( Reverse current overload test MST 25)	-	25000	-
10.21 IS/IEC 61730-2( Module breakage test MST 32)	-	25000	-
10.22 IS/IEC 61730-2(Screw connections test MST 33)	-	20000	-
10.23 IS/IEC 61730-2( Static Mechanical load test MST 34)	-	30000	-
10.24 IS/IEC 61730-2( Peel test MST 35)	-	80000	-
10.25 IS/IEC 61730-2( Lap shear strength test MST 36)	-	50000	-
10.26 IS/IEC 61730-2(Materials creep test MST 37)	-	20000	-
10.27 IS/IEC 61730-2( Robutness of terminations test MST 42)	-	20000	-
10.28 IS/IEC 61730-2(Thermal cycling test MST 51)	-	80000	-
10.29 IS/IEC 61730-2( Humidity-freeze test MST 52)	-	80000	-
10.30 IS/IEC 61730-2( Damp heat test MST 53)	-	80000	-
10.31 IS/IEC 61730-2(UV test MST 54)	-	30000	-
10.32 IS/IEC 61730-2( Cold conditioning MST 55)	-	80000	-
10.33 IS/IEC 61730-2( Dry heat conditioning MST 56)	-	80000	-
CL. 4,4.1(61730-2)	-	5000	-
CL. 4.2, 10.27, 10.28, 10.29, 10.30, 10.31, 10.32, 10.32.1, 10.32.2, 10.32.3, 10.32.4(61730-2)	-	55000	-
CL. 4.3(61730-2)	-	80000	-
CL. 4.4(61730-2)	-	20000	-
CL. 4.5(61730-2)	-	80000	-
CL. 4.6(61730-2)	-	15000	-
CL. 5(Table 6)(61730-2)	-	15000	-
CL. 7(61730-2)	-	10000	-
CL. 8(61730-2)	-	10000	-
CL. 9(61730-2)	-	10000	-
CL. 10, 10.1(61730-2)	-	10000	-
CL. 10.2, 10.2.1, 10.2.2, 10.2.3(61730-2)	-	10000	-
CL. 10.3, 10.3.1, 10.3.2, 10.3.3(61730-2)	-	80000	-
CL. 10.4, 10.4.1, 10.4.2, 10.4.3(61730-2)	-	30000	-
CL. 10.5, 10.5.1, 10.5.2, 10.5.3(61730-2)	-	10000	-
CL. 10.6(61730-2)	-	10000	-
CL. 10.7(61730-2)	-	10000	-
CL. 10.8,10.8.1,10.8.2,10.8.3(61730-2)	-	10000	-
CL. 10.9, 10.9.1, 10.9.2, 10.9.3,10.9.4,10.9.5(61730-2)	-	20000	-
CL. 10.10, 10.10.1, 10.10.2, 10.10.3, 10.10.4, 10.10.5(61730-2)	-	10000	-
CL. 10.11, 10.11.1, 10.11.2, 10.11.3, 10.11.4, 10.11.5(61730-2)	-	20000	-
CL. 10.12, 10.12.1, 10.12.2, 10.12.3, 10.12.4, 10.12.5(61730-2)	-	20000	-
CL. 10.13, 10.13.1, 10.13.2, 10.13.3(61730-2)	-	10000	-
CL. 10.14(61730-2)	-	20000	-
CL. 10.15, 10.15.1, 10.15.2, 10.15.2.1, 10.15.2.2, 10.15.3, 10.15.3.1, 10.15.3.2, 10.15.4(61730-2)	-	35000	-
CL. 10.16(61730-2)	-	35000	-
CL. 10.17, 10.17.1(61730-2)	-	70000	-
CL. 10.18, 10.18.1, 10.18.2, 10.18.2.1,10.18.2.2, 10.18.2.3, 10.18.2.4, 10.18.3, 10.18.3.1, 10.18.3.2,10.18.3.3, 10.18.4, 10.18.5, 10.18.5.1, 10.18.5.2, 10.18.5.3, 10.18.6, 10.18.7, 10.18.8(61730-2)	-	15000	-
CL. 10.19(61730-2)	-	25000	-
CL. 10.20, 10.20.1, 10.20.2, 10.20.3(61730-2)	-	25000	-
CL. 10.21, 10.21.1, 10.21.2, 10.21.3, 10.21.4(61730-2)	-	25000	-
CL. 10.22, 10.22.1, 10.22.1.1, 10.22.1.2, 10.22.2, 10.22.2.1, 10.22.2.2(61730-2)	-	20000	-
CL. 10.23, 10.23.1(61730-2)	-	30000	-
CL. 10.24, 10.24.1, 10.24.2 , 10.24.3,10.24.4 , 10.24.5(61730-2)	-	80000	-
CL. 10.25, 10.25.1, 10.25.2 , 10.25.3 , 10.25.4 , 10.25.5(61730-2)	-	50000	-
CL 10.26, 10.26.1, 10.26.2, 10.26.3 , 10.26.4, 10.26.5(61730-2)	-	20000	-
CL 10.27(61730-2)	-	20000	-
CL 10.28(61730-2)	-	80000	-
CL 10.28(61730-2)	-	80000	-
CL 10.30(61730-2)	-	80000	-
CL 10.31(61730-2)	-	30000	-
CL 10.32, 10.32.1, 10.32.2, 10.32.3, 10.32.4(61730-2)	-	80000	-
CL 10.33, 10.33.1, 10.33.2, 10.33.3, 10.33.4(61730-2)	-	80000	-
Annexure B.1, B.2,B.2.1,B.2.2, B.2.3,B.3(61730-2)	-	40000	-
Annexure A.1, A.2,A.3,A.4,A.5,A.6(61730-2)	-	10000	-

Complete

23 Jun, 2025

IS/IEC 62368 : Part 1 (2018)

Audio / Video, Information and Communication Technology Equipment Part 1 Safety Requirements ( First Revision )

85000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 4, 4.1, 4.1.1, 4.1.2, 4.1.3, 4.1.4, 4.1.5, 4.1.6, 4.1.7, 4.1.8, 4.1.9,4.1.10, 4.1.11,4.1.12, 4.1.13, 4.1.14,4.1.15(General Requirements)	-	500	-
Cl. 4.2, 4.2.1, 4.2.2, 4.2.3, 4.2.4(Energy source classifications)	-	1000	-
Cl. No. 4.3 ,4.4,4.5, 4.6,4.7,4.8,4.9,4.10 with all sub clauses(Protection against energy sources)	-	500	-
Cl. No. 5,5.1,5.2,5.3,5.4,5.5,5.6,5.7,5.8 with all sub clauses(Electrically-caused injury)	-	2000	-
Cl No. 6,6.1,6.2,6.3,6.4,6.5,6.6 with all sub clause(Electrically-caused fire)	-	2000	-
Cl. 7, 7.1, 7.2, 7.3, 7.4, 7.5, 7.6(Injury caused by hazardous substances)	-	4000	-
Cl. 8,8.1,8.2,8.3,8.4,8.5,8.6,8.7,8.8,8.9,8.10,8.11,8.12 with all sub clause(Mechanically-caused injury)	-	2000	-
Cl. 9, 9.1, 9.2, 9.2.1,9.2.2, 9.2.3, 9.3, 9.3.1, 9.3.2, 9.4, 9.5, 9.5.1, 9.5.2, 9.6, 9.6.1, 9.6.2, 9.6.3(Thermal burn injury)	-	3000	-
Annex. B, B.1, B.1.1, B.1.2, B.1.3, B.1.4, B.1.5,B.2,B.2.1, B.2.2, B.2.3, B.2.4, B.2.5, B.2.6, B.2.6.1, B.2.6.2, B.2.6.3, B.2.7, B.3, B.3.1, B.3.2, B.3.3, B.3.4, B.3.5, B.3.6, B.3.7, B.3.8, B.4, B.4.1, B.4.2, B.4.3, B.4.3.1, B.4.3.2,B.4.4, B.4.4.1, B.4.4.(Normal operating condition tests, abnormal operating condition tests and single fault condition tests)	-	4000	-
Annex. D, D.1, D.2, D.3(Test Generators)	-	6000	-
Annex E, E.1, E.2, E.3(Test conditions)	-	3000	-
Annex. F, F.1, F.2, F2.1, F.2.2,F2.3,F.3, F.3.1, F.3.2, F.3.2.1,F.3.2.2, F.3.3,F.3.3.1, F.3.3.2,F.3.3.3, F.3.3.4, F.3.3.5, F.3.3.6,F.3.3.7, F.3.3.8, F.3.4, F.3.5, F.3.5.1,F.3.5.2, F.3.5.3, F.3.5.4, F.3.5.5,F.3.5.6, F.3.5.7,F.3.6, F.3.6.1, F.3.6.1.1, F.3.6(Equipment markings, instructions, and instructional safeguards)	-	4000	-
Annex. G, G.1, G.1.1, G.1.2, G.1.3, G.2, G.2.1, G.2.2, G.2.3, G.2.4, G.3, G.3.1, G.3.1.1, G.3.1.2, G.3.2, G.3.2.1,G.3.2.2, G.3.3,G.3.4, G.3.5, G.3.5.1, G.3.5.2, G.4, G.4.1, G.4.2, G.4.3, G.5, G.5.1, G.5.1.1, G.5.1.2,G.5.1.3,G.5.2,G.5.2.1, G.5.2.2, G.5.2.3(Components)	-	4000	-
Annex I(Overvoltage categories)	-	4000	-
Annex. J, J.1, J.2, J.2.1, J.2.2, J.2.2.1, J.2.2.1.1, J.2.2.1.2, J.2.2.1.3, J.2.2.2, J.2.3, J.2.4, J.2.5, J.3, J.3.1, J.3.2, J.3.3(Insulated winding wires for use without interleaved insulation)	-	4000	-
Annex. K, K.1, K.1.1, K.1.2, K.2, K.3, K.4, K.5, K.5.1, K.5.2, K.6, K.6.1, K.6.2, K.7, K.7.1, K.7.2, K.7.3, K.7.4(Safety Interlocks)	-	5000	-
Annex. L, L.1, L.2, L.3, L.4, L.5, L.6, L.7, L.8, L.9,(Disconnect devices)	-	1000	-
Annex. M, M.1, M.2, M.2.1, M.2.2, M.3, M.3.1, M.3.2, M.3.3, M.4, M.4.1, M.4.2,M.4.2.1, M.4.2.2,M.4.3, M.4.4,M.4.4.1, M.4.4.2,M.4.4.3, M.4.4.4, M.4.4.5, M.4.4.6, M.5, M.5.1, M.5.2, M.6, M.6.1, M.6.2, M.7, M.7.1, M.7.2, M.7.3, M.7.3.1,M.7.3.2, M.7.3.3, M.7.(Equipment containing batteries and their protection circuits)	-	2000	-
Annex. N(Electrochemical potentials)	-	2000	-
Annex. O(Measurement of creepage distances and clearances)	-	3000	-
Annex. P, P.1, P.2, P.2.1, P.2.2, P.2.3, P.2.3.1, P.2.3.2, P.3, P.3.1, P.3.2, P.3.3, P.3.4, P.4, P.4.1, P.4.2(Safeguards against conductive objects)	-	2000	-
Annex. Q, Q.1, Q.1.1, Q.1.2, Q.2(Circuits intended for interconnection with building wiring)	-	2000	-
Annex. R, R.1, R.2, R.3, R.4(Limited short-circuit test)	-	5000	-
Annex. S, S.1, S.2, S.3, S.3.1, S.3.2, S.4, S.5(Tests for resistance to heat and fire)	-	5000	-
Annex. T, T.1, T.2, T.3, T.4, T.5, T.6, T.7, T.8, T.9, T.10, T.11(Mechanical strength tests)	-	8000	-
Annex. V, V.1, V.1.1, V.1.2, V.1.3, V.1.4, V.1.5, V.1.6, V.2(Determination of accessible parts)	-	4000	-
Annex. X(Alternative method for determining clearances for insulation in circuits connected to an AC mains not exceeding 420V peak (300V rms))	-	1000	-
Annex. Y, Y.1, Y.2, Y.3, Y.3.1, Y.3.2, Y.3.3, Y.3.4, Y.3.5, Y.4, Y.4.1 Y.4.2, Y.4.3, Y.4.4, Y.4.5, Y.5, Y.5.1, Y.5.2, Y.5.3, Y.5.4, Y.5.5, Y.5.5.1, Y.5.5.2, Y.5.5.3, Y.6, Y.6.1, Y.6.2(Construction requirements for outdoor enclosure)	-	1000	-

Complete

23 Jun, 2025

IS 6290 (1986)

Specification for steam irons (First Revision)

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 5,5.1,5.2(6290)	-	250	-
Cl.6,6.1(6290)	-	250	-
Cl.7,7.1,7.12,7.14,7.101,7.102(6290)	-	500	-
CL 8(6290)	-	500	-
Cl.9(6290)	-	500	-
CL 10(6290)	-	500	-
CL 11(6290)	-	1500	-
CL 12(6290)	-	500	-
CL 13(6290)	-	800	-
Cl.14(6290)	-	800	-
CL 15(6290)	-	2000	-
CL 16(6290)	-	800	-
Cl.17(6290)	-	500	-
CL 18(6290)	-	1000	-
CL 19(6290)	-	1000	-
Cl.20(6290)	-	700	-
Cl 21(6290)	-	1000	-
Cl.22, 22.101, 22.102, 22.103, 22.104,22.105, 22.106, 22.107, 22.108,22.109(6290)	-	1000	-
Cl.23(6290)	-	600	-
Cl.24,24.101(6290)	-	900	-
CL 25(6290)	-	900	-
Cl.26(6290)	-	900	-
Cl.27(6290)	-	800	-
Cl.28(6290)	-	500	-
Cl.29(6290)	-	700	-
Cl.30(6290)	-	1000	-
Cl.31(6290)	-	800	-
Cl.32(6290)	-	500	-
Cl.33(6290)	-	100	-
Cl.101,101.1 ,101.2 101.3 ,101.4, 101.5 101.6 ,101.7(6290)	-	1700	-
CL 102(6290)	-	1700	-
Cl.103,103.1,103.2, 103.3(6290)	-	1800	-
Cl.104.1, 104.2(6290)	-	1800	-
Cl.105,105.1,105.2,105.3,105.4,105.(6290)	-	2700	-
Cl.106,106.1,106.2(6290)	-	2700	-
CL 107.1(6290)	-	2800	-
Cl.107.2,107.3(6290)	-	3000	-

Complete

23 Jun, 2025

IS 13273 (1991)

Vitreous enamelled inner tanks for storage water heater - specification

27000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 5.3.2.1(1238)	-	500	-
Cl. 5.3.2.1(1238)	-	500	-
Cl. 5.3.2.3(13273)	-	2000	-
Cl 5.3.2.2(13273)	-	2500	-
Cl. 5.3.3(13273)	-	1500	-
Cl. 5.3.2.2(3972(P-2/Sec-1))	-	500	-
Cl. 5.3.2.2(3972(P-2/Sec-1))	-	3000	-
Cl. 5.3.2.2(3972(P-2/Sec-1))	-	3000	-
Cl. 5.3.2.2(3972(P-2/Sec-1))	-	2500	-
Cl. 5.3.2.5(13273)	-	3500	-
Cl. 5.4(13273)	-	2500	-
Cl. 5.5(13273)	-	5000	-

Complete

23 Jun, 2025

IS 12510 (1988)

Specification for wall clocks (Battery Operated)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 3, 3.0 to 3.5, 3.5.1 to 3.5.3(12510)	-	1500	-
Cl. 4, 4.1 to 4.4(12510)	-	5000	-
Cl. 3, 3.0 to 3.5, 3.5.1 to 3.5.3(12510)	-	1500	-
Cl. 4, 4.1 to 4.4(12510)	-	5000	-
Cl. 5, 5.1, 5.2, 5.2.1, 5.2.1.1, 5.2.2(12510)	-	1500	-
Cl. 7(12510)	-	1000	-
Cl. 8, 8.1(12510)	-	1000	-

Complete

23 Jun, 2025

IS/IEC 60695 : Part 11 : Sec 10 (2013)

Fire hazard testing: Part 11 test flames :: Sec 10 50 w horizontal and vertical flame test methods

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 8(60695-11-10)	-	20000		-
Cl. 9(60695-11-10)	-	20000		-

Complete

23 Jun, 2025

IS 7872 (2020)

Deep Freezers - Specification ( Second Revision )

165000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Refrigeration system)	-	5000	-
5.4.2(Individual Strength - Pressure Test)	-	833	-
5.4.3(Individual Strength - Pressure Test)	-	833	-
5.4.4(Fatigue Test)	-	833	-
6(Safety Requirements)	-	7000	-
7(Sound Pressure Level)	-	8000	-
8(Freezer Storage Capacity)	-	15000	-
11.1(No load Pull down Test)	-	25000	-
11.2(Energy Consumption Test)	-	35000	-
11.3(Temperature Rise Test)	-	20000	-
11.4(Door Seal Test)	-	10000	-
11.5(Mechanical Strength of Shelves and Similar Components)	-	10000	-
11.6(Thermal Insulation Test ( External Condensation))	-	10000	-
11.7(Pressure Test)	-	10000	-
13(Marking and Instruction)	-	1500	-
4.8(Door and Fittings)	-	2500	-
5.5(Strength Pressure test for components)	-	833	-
5.6(External surface condensation test)	-	833	-
5.1(Sound level)	-	833	-
6(Measurement of freezer storage capacity)	-	3500	-
6.11(Volume measurement Water fill method)	-	3500	-
9.1(No load test)	-	500	-
9.2.1(Pull down time)	-	500	-
9.2.2(Power consumption & percentage running time)	-	500	-

Complete

23 Jun, 2025

IS/IEC 61730 : PART 1 (2016)

Photovoltaic (PV) Module Safety Qualification Part 1 Requirements for Construction ( First Revision )

190000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.0(Application Classes)	-	7500	-
4.0(Construction Requirements)	-	10000	-
5.0(Polymeric Materials)	-	10000	-
4 IS/IEC 61730-1( Classification, Application and Inteded Use)	-	12500	-
5, 5.1 IS/IEC 61730-1( Requirements for design and Construction)	-	10000	-
5.2 IS/IEC 61730-1( Marking and Documentation)	-	12500	-
5.3, 5.3.1 IS/IEC 61730-1( Electrical Components and Insualtion)	-	35000	-
5.3.2 IS/IEC 61730-1( Internal Wiring)	-	3888	-
5.3.3 IS/IEC 61730-1( External Wirings and cables)	-	3888	-
5.3.4 IS/IEC 61730-1( Connectors)	-	3888	-
5.3.5 IS/IEC 61730-1( Junction Box for PV modules)	-	3888	-
5.3.6 IS/IEC 61730-1( Front sheet and back Sheet)	-	3888	-
5.3.7 IS/IEC 61730-1( Insulation Barrier)	-	3888	-
5.3.8 IS/IEC 61730-1( Electrical Connections)	-	3888	-
5.3.9 IS/IEC 61730-1( Encapsulants)	-	3888	-
5.3.10 IS/IEC 61730-1( Bypass Diodes)	-	3888	-
5.4, 5.4.1 IS/IEC 61730-1( Mechanical and Electromechanical connections)	-	45000	-
5.4.2 IS/IEC 61730-1( Screw Connctions)	-	7500	-
5.4.3 IS/IEC 61730-1( Rivets)	-	7500	-
5.4.4 IS/IEC 61730-1( Thread Cutting Screws)	-	7500	-
5.4.5 IS/IEC 61730-1( Form/Press/Tight/Fit)	-	7500	-
5.4.6 IS/IEC 61730-1( Connections by adhesives)	-	7500	-
5.4.7 IS/IEC 61730-1( Other Connections)	-	7500	-
5.5, 5.5.1 IS/IEC 61730-1( Materials)	-	22500	-
5.5.2 IS/IEC 61730-1( Polymeric Materials)	-	2500	-
5.5.2.3.2 IS/IEC 61730-1( Endurance to Electrical Stress)	-	2500	-
5.5.2.3.3 IS/IEC 61730-1( Endurance to thermal stress-RTE (RTI) or TI )	-	2500	-
5.5.2.3.4 IS/IEC 61730-1( Polymeric Insulating materials used as external Parts)	-	2500	-
5.5.2.3.5 IS/IEC 61730-1(Polymeric Insulating Parts supporting live Parts)	-	2500	-
5.5.2.4 IS/IEC 61730-1(Polymeric Meterial used for Mechanical functions )	-	2500	-
5.5.3, 5.5.3.1 IS/IEC 61730-1(Metallic materials)	-	2500	-
5.5.3.2 IS/IEC 61730-1( Current Carrying Parts)	-	2500	-
5.5.4 IS/IEC 61730-1(Adhesives)	-	2500	-
5.6, 5.6.1 IS/IEC 61730-1( Protection Agianst Electric Shock)	-	25000	-
5.6.2 IS/IEC 61730-1( Protection Agianst accessibility to hazardeous live parts)	-	8333	-
5.6.3 IS/IEC 61730-1(Insulation Coordination)	-	8333	-
5.6.4 IS/IEC 61730-1( Distance through Insulation)	-	8333	-
4 IS/IEC 61730-1( Classification, Application and Inteded Use)	-	12500	-
5, 5.1 IS/IEC 61730-1( Requirements for design and Construction)	-	10000	-
5.2 IS/IEC 61730-1( Marking and Documentation)	-	12500	-
5.3, 5.3.1 IS/IEC 61730-1( Electrical Components and Insualtion)	-	35000	-
5.3.2 IS/IEC 61730-1( Internal Wiring)	-	3888	-
5.3.3 IS/IEC 61730-1( External Wirings and cables)	-	3888	-
5.3.4 IS/IEC 61730-1( Connectors)	-	3888	-
5.3.5 IS/IEC 61730-1( Junction Box for PV modules)	-	3888	-
5.3.6 IS/IEC 61730-1( Front sheet and back Sheet)	-	3888	-
5.3.7 IS/IEC 61730-1( Insulation Barrier)	-	3888	-
5.3.8 IS/IEC 61730-1( Electrical Connections)	-	3888	-
5.3.9 IS/IEC 61730-1( Encapsulants)	-	3888	-
5.3.10 IS/IEC 61730-1( Bypass Diodes)	-	3888	-
5.4, 5.4.1 IS/IEC 61730-1( Mechanical and Electromechanical connections)	-	45000	-
5.4.2 IS/IEC 61730-1( Screw Connctions)	-	7500	-
5.4.3 IS/IEC 61730-1( Rivets)	-	7500	-
5.4.4 IS/IEC 61730-1( Thread Cutting Screws)	-	7500	-
5.4.5 IS/IEC 61730-1( Form/Press/Tight/Fit)	-	7500	-
5.4.6 IS/IEC 61730-1( Connections by adhesives)	-	7500	-
5.4.7 IS/IEC 61730-1( Other Connections)	-	7500	-
5.5, 5.5.1 IS/IEC 61730-1( Materials)	-	22500	-
5.5.2 IS/IEC 61730-1( Polymeric Materials)	-	2500	-
5.5.2.3.2 IS/IEC 61730-1( Endurance to Electrical Stress)	-	2500	-
5.5.2.3.3 IS/IEC 61730-1( Endurance to thermal stress-RTE (RTI) or TI )	-	2500	-
5.5.2.3.4 IS/IEC 61730-1( Polymeric Insulating materials used as external Parts)	-	2500	-
5.5.2.3.5 IS/IEC 61730-1(Polymeric Insulating Parts supporting live Parts)	-	2500	-
5.5.2.4 IS/IEC 61730-1(Polymeric Meterial used for Mechanical functions )	-	2500	-
5.5.3, 5.5.3.1 IS/IEC 61730-1(Metallic materials)	-	2500	-
5.5.3.2 IS/IEC 61730-1( Current Carrying Parts)	-	2500	-
5.5.4 IS/IEC 61730-1(Adhesives)	-	2500	-
5.6, 5.6.1 IS/IEC 61730-1( Protection Agianst Electric Shock)	-	25000	-
5.6.2 IS/IEC 61730-1( Protection Agianst accessibility to hazardeous live parts)	-	833	-
5.6.3 IS/IEC 61730-1(Insulation Coordination)	-	833	-
5.6.4 IS/IEC 61730-1( Distance through Insulation)	-	833	-

Complete

23 Jun, 2025

IS/IEC 60335 : Part 2 : Sec 89 (2010)

Household and similar electrical appliances - Safety: Part 2 - 89: particular requirements for commercial refrigerating appliances with an incorporated or remote refrigerant unit or compressor

115000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1 , 7.12, 7.14,7.15(Marking)	-	3400	-
8, 8.1(Protection against access to live parts)	-	1200	-
8.1.1 to 8.1.5(Protection against access to live parts)	-	1200	-
8.2(Protection against access to live parts)	-	1200	-
10.1(Power input and current)	-	2500	-
10.101 (Power input and current)	-	2500	-
11(TEMPERATURE RISE)	-	5000	-
11.2(TEMPERATURE RISE)	-	555	-
11.4(TEMPERATURE RISE)	-	555	-
11.5(TEMPERATURE RISE)	-	555	-
11.6(TEMPERATURE RISE)	-	555	-
11.7(TEMPERATURE RISE)	-	555	-
11.8(TEMPERATURE RISE)	-	555	-
11.101(TEMPERATURE RISE)	-	555	-
11.102(TEMPERATURE RISE)	-	555	-
11.103(TEMPERATURE RISE)	-	555	-
13(ELECTRICAL INSULATION AND LEAKAGE CURRENT AT OPERATING TEMPERATURE)	-	4500	-
13.2(ELECTRICAL INSULATION AND LEAKAGE CURRENT AT OPERATING TEMPERATURE)	-	2250	-
13.3 & table 4,5(ELECTRICAL INSULATION AND LEAKAGE CURRENT AT OPERATING TEMPERATURE)	-	2250	-
14(Transient Over Voltage & table 6)	-	4000	-
15(Moisture resistance)	-	12000	-
15.1.1(Moisture resistance)	-	1714	-
15.1.2(Moisture resistance)	-	1714	-
15.2(Moisture resistance)	-	1714	-
15.3(Moisture resistance)	-	1714	-
15.101(Moisture resistance)	-	1714	-
15.102(Moisture resistance)	-	1714	-
15.103(Moisture resistance)	-	1714	-
16 & 16.1(Leakage current and electric strength)	-	5500	-
16.2(Leakage current and electric strength)	-	2750	-
16.3 & table 7(Leakage current and electric strength)	-	2750	-
17(Overload protection of transformers and associated circuits)	-	4000	-
19(ABNORMAL OPERATION)	-	15000	-
19.2(ABNORMAL OPERATION)	-	790	-
19.3(ABNORMAL OPERATION)	-	790	-
19.4(ABNORMAL OPERATION)	-	790	-
19.5(ABNORMAL OPERATION)	-	790	-
19.6(ABNORMAL OPERATION)	-	790	-
19.7 & table 8(ABNORMAL OPERATION)	-	790	-
19.8(ABNORMAL OPERATION)	-	790	-
19.9(ABNORMAL OPERATION)	-	790	-
19.1(ABNORMAL OPERATION)	-	790	-
19.11(ABNORMAL OPERATION)	-	790	-
19.11.1(ABNORMAL OPERATION)	-	790	-
19.11.2(ABNORMAL OPERATION)	-	790	-
19.11.3(ABNORMAL OPERATION)	-	790	-
19.11.4(ABNORMAL OPERATION)	-	790	-
19.11.4.1(ABNORMAL OPERATION)	-	790	-
19.12(ABNORMAL OPERATION)	-	790	-
19.13(ABNORMAL OPERATION)	-	790	-
19.14(ABNORMAL OPERATION)	-	790	-
19.15(ABNORMAL OPERATION)	-	790	-
20.1(Stability and mechanical hazards)	-	2500	-
20.2(Stability and mechanical hazards)	-	2500	-
21.1(MECHANICAL STRENGTH)	-	1000	-
21.2(MECHANICAL STRENGTH)	-	1000	-
22.101(MECHANICAL STRENGTH)	-	1000	-
22.102(MECHANICAL STRENGTH)	-	1000	-
22.1(Constructions)	-	3000	-
22.2(Constructions)	-	230	-
22.3(Constructions)	-	230	-
22.4(Constructions)	-	230	-
22.5(Constructions)	-	230	-
22.6(Constructions)	-	230	-
22.7 to 22.10(Constructions)	-	230	-
22.11(Constructions)	-	230	-
22.12(Constructions)	-	230	-
22.13 to 22.52(Constructions)	-	230	-
22.101 to 22.102(Constructions)	-	230	-
22.103(Constructions)	-	230	-
22.104(Constructions)	-	230	-
22.105 to 22.114(Constructions)	-	230	-
22.104(Constructions)	-	230	-
23.1 & 23.2(Internal wiring)	-	1000	-
23.3(Internal wiring)	-	1000	-
23.4(Internal wiring)	-	1000	-
23.5 to 23.8(Internal wiring)	-	1000	-
23.9 ,23.10(Internal wiring)	-	1000	-
24(Components)	-	8000	-
24.2 to 24.5 (Components)	-	4000	-
25.1(Supply connection and external flexible cords)	-	2500	-
25.2 to 25.25(Supply connection and external flexible cords)	-	2500	-
26, 26.1 to 26.11(Terminals for external conductors)	-	2000	-
27, 27.1 to 27.6(Provision for earthing)	-	3000	-
28.1, Table No.-14(Screws and connections)	-	2000	-
28.2 to 28.4(Screws and connections)	-	2000	-
29 and table (creepage and Clearances distances )	-	1500	-
29.1 & 29.3(creepage and Clearances distances )	-	1500	-
30.1(Resistance to heat and fire)	-	1800	-
30.2(Resistance to heat and fire)	-	1800	-
30.2.1(Resistance to heat and fire)	-	1800	-
30.2.2(Resistance to heat and fire)	-	1800	-
30.2.3(Resistance to heat and fire)	-	1800	-
31(Resistance to rusting)	-	3000	-
7.1 , 7.12, 7.14,7.15(Marking)	-	3400	-
8, 8.1(Protection against access to live parts)	-	1200	-
8.1.1 to 8.1.5(Protection against access to live parts)	-	1200	-
8.2(Protection against access to live parts)	-	1200	-
10.1(Power input and current)	-	2500	-
10.101 (Power input and current)	-	2500	-
11(TEMPERATURE RISE)	-	5000	-
11.2(TEMPERATURE RISE)	-	555	-
11.4(TEMPERATURE RISE)	-	555	-
11.5(TEMPERATURE RISE)	-	555	-
11.6(TEMPERATURE RISE)	-	555	-
11.7(TEMPERATURE RISE)	-	555	-
11.8(TEMPERATURE RISE)	-	555	-
11.101(TEMPERATURE RISE)	-	555	-
11.102(TEMPERATURE RISE)	-	555	-
11.103(TEMPERATURE RISE)	-	555	-
13(ELECTRICAL INSULATION AND LEAKAGE CURRENT AT OPERATING TEMPERATURE)	-	4500	-
13.2(ELECTRICAL INSULATION AND LEAKAGE CURRENT AT OPERATING TEMPERATURE)	-	2250	-
13.3 & table 4,5(ELECTRICAL INSULATION AND LEAKAGE CURRENT AT OPERATING TEMPERATURE)	-	2250	-
14(Transient Over Voltage & table 6)	-	4000	-
15(Moisture resistance)	-	12000	-
15.1.1(Moisture resistance)	-	1714	-
15.1.2(Moisture resistance)	-	1714	-
15.2(Moisture resistance)	-	1714	-
15.3(Moisture resistance)	-	1714	-
15.101(Moisture resistance)	-	1714	-
15.102(Moisture resistance)	-	1714	-
15.103(Moisture resistance)	-	1714	-
16 & 16.1(Leakage current and electric strength)	-	5500	-
16.2(Leakage current and electric strength)	-	2750	-
16.3 & table 7(Leakage current and electric strength)	-	2750	-
17(Overload protection of transformers and associated circuits)	-	4000	-
19(ABNORMAL OPERATION)	-	15000	-
19.2(ABNORMAL OPERATION)	-	790	-
19.3(ABNORMAL OPERATION)	-	790	-
19.4(ABNORMAL OPERATION)	-	790	-
19.5(ABNORMAL OPERATION)	-	790	-
19.7 & table 8(ABNORMAL OPERATION)	-	790	-
19.8(ABNORMAL OPERATION)	-	790	-
19.9(ABNORMAL OPERATION)	-	790	-
19.11(ABNORMAL OPERATION)	-	790	-
19.11.1(ABNORMAL OPERATION)	-	790	-
19.11.2(ABNORMAL OPERATION)	-	790	-
19.11.3(ABNORMAL OPERATION)	-	790	-
19.11.4(ABNORMAL OPERATION)	-	790	-
19.11.4.1(ABNORMAL OPERATION)	-	790	-
19.12(ABNORMAL OPERATION)	-	790	-
19.13(ABNORMAL OPERATION)	-	790	-
19.14(ABNORMAL OPERATION)	-	790	-
19.15(ABNORMAL OPERATION)	-	790	-
20.1(Stability and mechanical hazards)	-	2500	-
20.2(Stability and mechanical hazards)	-	2500	-
21.1(MECHANICAL STRENGTH)	-	1000	-
21.2(MECHANICAL STRENGTH)	-	1000	-
22.101(MECHANICAL STRENGTH)	-	1000	-
22.102(MECHANICAL STRENGTH)	-	1000	-
22.1(Constructions)	-	3000	-
22.2(Constructions)	-	230	-
22.3(Constructions)	-	230	-
22.4(Constructions)	-	230	-
22.5(Constructions)	-	230	-
22.6(Constructions)	-	230	-
22.7 to 22.10(Constructions)	-	230	-
22.11(Constructions)	-	230	-
22.12(Constructions)	-	230	-
22.13 to 22.52(Constructions)	-	230	-
22.101 to 22.102(Constructions)	-	230	-
22.103(Constructions)	-	230	-
22.104(Constructions)	-	230	-
22.104(Constructions)	-	230	-
22.105 to 22.114(Constructions)	-	230	-
22.104(Constructions)	-	230	-
23.1 & 23.2(Internal wiring)	-	1000	-
23.3(Internal wiring)	-	1000	-
23.4(Internal wiring)	-	1000	-
23.5 to 23.8(Internal wiring)	-	1000	-
23.9 ,23.10(Internal wiring)	-	1000	-
24(Components)	-	8000	-
24.2 to 24.5 (Components)	-	4000	-
25.1(Supply connection and external flexible cords)	-	2500	-
25.2 to 25.25(Supply connection and external flexible cords)	-	2500	-
26, 26.1 to 26.11(Terminals for external conductors)	-	2000	-
27, 27.1 to 27.6(Provision for earthing)	-	3000	-
28.1, Table No.-14(Screws and connections)	-	2000	-
28.2 to 28.4(Screws and connections)	-	2000	-
29 and table (creepage and Clearances distances )	-	1500	-
29.1 & 29.3(creepage and Clearances distances )	-	1500	-
30.1(Resistance to heat and fire)	-	9000	-
30.2(Resistance to heat and fire)	-	1800	-
30.2.1(Resistance to heat and fire)	-	1800	-
30.2.2(Resistance to heat and fire)	-	1800	-
30.2.3(Resistance to heat and fire)	-	1800	-
31(Resistance to rusting)	-	3000	-

Complete

23 Jun, 2025

IS 16221 : Part 2 (2015)

Safety of power converters for use in photovoltaic power systems: Part 2 particular requirements for inverters

400000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(General Test Requireements)	-	50000	-
5(Marking and documentation)	-	20000	-
6(Environmental requirements and conditions)	-	50000	-
7(Protection against electric shock and energy hazards)	-	50000	-
8(Protection against Mechanical Hazards)	-	50000	-
9(Protection against Fire Hazards)	-	50000	-
10(Protection against Sonic Pressure Hazards)	-	25000	-
11(Protection against Liquid Hazards)	-	25000	-
12(Protection against Chemical Hazards)	-	20000	-
13(Physical Requirements)	-	30000	-
14(Components)	-	30000	-
14(Components)	-	30000	-
4(General Test Requirements)	-	50000	-
5(Marking and documentation)	-	20000	-
6(Environmental requirements and conditions)	-	50000	-
7(Protection against electric shock and energy hazards)	-	50000	-
8(Protection against Mechanical Hazards)	-	50000	-
9(Protection against Fire Hazards)	-	50000	-
10(Protection against Sonic Pressure Hazards)	-	25000	-
11(Protection against Liquid Hazards)	-	25000	-
12(Protection against Chemical Hazards)	-	20000	-
13(Physical Requirements)	-	30000	-
14(Components)	-	30000	-

Complete

23 Jun, 2025

IS 16103 : Part 1 (2012)

Led modules for general lighting: Part 1 safety requirements

37500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking)	-	4000	1000
21(Heat management)	-	4000	-
8(Terminals)	-	1500	-
9(PROVISION FOR EARTHING)	-	2000	-
10(Protection against accidental contact with live parts)	-	2000	-
11(Mositure Resistance and Insulation)	-	8000	-
12(Electric Strength)	-	5000	-
13(Fault conditions)	-	3000	-
15(Construction)	-	1000	-
16(Creepage distance and clearances)	-	1000	-
17(Screws, current carrying parts and connections)	-	2000	-
18(Resistance to heat, fire and tracking)	-	6000	-
19(Resistance to corrosion)	-	1000	-

Complete

23 Jun, 2025

IS 14286 : Part 1 : Sec 1 (2019)

Terrestrial photovoltaic (PV) modules - Design qualification and type approval: Part 1 test requirements: Sec 1 special requirements for testing of crystalline silicon photovoltaic (Pv) modules (Second Revision)

700000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11.1(Visual inspection (MQT 01))	-	20000	-
11.2(Maximum power determination (MQT 02))	-	20000	-
11.3(Insulation test (MQT 03))	-	10000	-
11.4(Measurement of temperature coefficients (MQT 04))	-	30000	-
11.5(Measurement of nominal module operating temperature (NMOT) (MQT 05))	-	30000	-
11.6(Performance at STC and NMOT (MQT 06))	-	30000	-
11.7(Performance at low irradiance (MQT 07))	-	30000	-
11.8(Outdoor exposure test (MQT 08))	-	30000	-
11.9(Hot-spot endurance test (MQT 09))	-	45000	-
11.1(UV preconditioning test (MQT 10))	-	30000	-
11.11(Thermal cycling test (MQT 11))	-	70000	-
11.12(Humidity-freeze test (MQT 12))	-	85000	-
11.13(Damp heat test (MQT 13))	-	100000	-
11.14(Robustness of terminations (MQT 14))	-	20000	-
11.15(Wet leakage current test (MQT 15))	-	20000	-
11.16(Static mechanical load test (MQT 16))	-	30000	-
11.17(Hail test (MQT 17))	-	30000	-
11.18(Bypass diode thermal test (MQT 18))	-	40000	-
11.19(Stabilization (MQT 19))	-	30000	-

Complete

23 Jun, 2025

IS 14286 : Part 1 (2019)

Terrestrial photovoltaic (PV) modules - Design qualification and type approval: Part 1 test requirements (Second Revision)

1100000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11(Test flow and procedures)	-	100000	-
5(Marking and documentation)	-	100000	-
7(Pass criteria)	-	300000	-
6(Testing)	-	100000	-
8(Major visual defects)	-	200000	-
8(Major visual defects)	-	200000	-
9(Report)	-	150000	-
10(Modifications)	-	150000	-

Complete

23 Jun, 2025

IS 302 : Part 2 : Sec 8 (1994)

Safety of household and similar electrical appliances : part 2 particular requirements, section 8 electrical shavers hair, clippers and similar appliances

24000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Rating)	-	500	-
6(Classification)	-	500	-
7(Marking/ Marking & Instructions)	-	500	-
8(Protection against Electric Shock/ Protection against Access to Live Parts)	-	750	-
9(Starting Of Motor Operated Appliances)	-	500	-
10(Power Input & Current)	-	1000	-
11(Temperature Rise/Heating)	-	1500	-
13(Leakage Current and Electric Strength at Operating Temperature)	-	750	-
14(Radio and Television Interference Suppression/ Transient Over Voltage)	-	750	-
15(Moisture Resistance)	-	2000	-
16(Leakage Current and Electric Strength)	-	750	-
17(Overload Protection/ Overload Protection of Transformers & Associated Circuits)	-	250	-
18(Endurance)	-	1500	-
19(Abnormal Operation)	-	2000	-
20(Stability & Mechanical Hazards)	-	500	-
21(Mechanical strength)	-	750	-
22(Construction)	-	1000	-
23(Internal wiring)	-	750	-
24(Component)	-	1000	-
25(Supply Connection & External Flexible Cables and Cords)	-	1500	-
26(Terminals For External Conductors)	-	750	-
27(Provision For Earthing)	-	1000	-
28(Screws & Connection)	-	750	-
29(Clearances, Creepage Distances & Solid Insulation)	-	1000	-
30(Resistance to Heat & Fire)	-	750	-
31(Resistance to Rusting)	-	750	-
32(Radiation ,Toxicity and similar hazards)	-	250	-

Complete

23 Jun, 2025

IS 302 : Part 2 : Sec 6 (2009)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 6 cooking ranges, hobs, ovens and similar appliances (First Revision)

19000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.0(Classification)	-	250	-
7.0(Marking and instructions)	-	250	-
8.0(Protection against access to live part test)	-	250	-
9.0(Starting of motor-operated appliances test)	-	250	-
10.0(Power Input and current test)	-	800	-
11.0(Heating test)	-	1000	-
13.0(Leakage current and electric strength test)	-	500	-
14.0(Transient voltages)	-	1200	-
15.0(Moisture Resistance)	-	1500	-
16.0(Leakage current and electric strength test)	-	500	-
17.0(Overload protection of transformers test)	-	250	-
18.0(Endurance test)	-	250	-
19.0(Abnormal Operations)	-	1000	-
20.0(Stability and Mechanical Hazards)	-	700	-
21.0(Mechanical Strength)	-	700	-
22.0(Construction verification related tests)	-	1000	-
23.0(Internal wiring)	-	950	-
24.0(Components)	-	1000	-
25.0(Supply connections and External Flexible Cords)	-	1500	-
26.0(Terminal for External Conductors)	-	500	-
27.0(Provision for Earthing)	-	950	-
28.0(Screws and connections)	-	500	-
29.0(Clearances and Creepage distances and solid insulation)	-	1500	-
30.0(Resistance to heat and fire)	-	950	-
31.0(Resistance to rusting)	-	500	-
32.0(Radiation, Toxicity and Similar hazards)	-	250	-

Complete

23 Jun, 2025

IS 302 : Part 2 : Sec 3 (2007)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 3 electric iron (First Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Classification- IS 302-1 )	-	200	-
6(Classification- IS 302-1)	-	200	-
7.1(Marking- IS 302-1)	-	500	-
7.1(Marking- IS 302-1)	-	50	-
7.1(Marking- IS 302-1)	-	50	-
7.1(Marking- IS 302-1)	-	50	-
7.1(Marking- IS 302-1)	-	50	-
7.1(Marking- IS 302-1)	-	50	-
7.1(Marking- IS 302-1)	-	50	-
7.1(Marking- IS 302-1)	-	50	-
7.1(Marking- IS 302-1)	-	50	-
7.3(Marking- IS 302-1)	-	50	-
7.4(Marking- IS 302-1)	-	50	-
7.6(Marking- IS 302-1)	-	50	-
7.7(Marking- IS 302-1)	-	50	-
7.8(Marking- IS 302-1)	-	50	-
7.11(Marking- IS 302-1)	-	50	-
7.12(Marking- IS 302-1)	-	50	-
7.13(Marking- IS 302-1)	-	50	-
7.14(Marking- IS 302-1)	-	50	-
7.15(Marking- IS 302-1)	-	50	-
7.101(Marking)	-	50	-
8( Protection Against Electric Shock, IS 302-1)	-	250	-
10(Power Input and Current, IS 302-1)	-	600	-
11(Heating, IS 302-1)	-	500	-
11(Heating, IS 302-1)	-	500	500
11(Heating, IS 302-1)	-	500	-
11(Heating, IS 302-1)	-	500	-
11(Heating, IS 302-1)	-	500	-
11(Heating, IS 302-1)	-	500	-
11(Heating, IS 302-1)	-	500	-
11(Heating, IS 302-1)	-	500	-
13(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-	300	-
13(Electrical Insulation and Leakage Current at Operating Temperature: High Voltage, IS 302-1)	-	300	-
14(Transient Over Voltages, IS 302-1)	-	500	-
15.1(Moisture Resistance, IS 302-1)	-	300	-
15.2(Moisture Resistance, IS 302-1)	-	300	-
15.3(Moisture Resistance, IS 302-1)	-	300	-
16(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-	450	-
16(Electrical Insulation and Leakage Current at Operating Temperature: High Voltage, IS 302-1)	-	450	-
19.4(Abnormal Operation, IS 302-1)	-	100	-
19.4(Abnormal Operation, IS 302-1)	-	100	-
19.5(Abnormal Operation, IS 302-1)	-	100	-
19.5(Abnormal Operation, IS 302-1)	-	100	-
19.7(Abnormal Operation)	-	100	-
19.9(Abnormal Operation)	-	100	-
19.1(Abnormal Operation)	-	100	-
19.101(Abnormal Operation)	-	100	-
20.1(Stability & Mechanical Hazards, IS 302-1)	-	150	-
20.2(Stability & Mechanical Hazards, IS 302-1)	-	150	-
21.1(Mechanical Strength, IS 302-1)	-	200	-
21.2(Mechanical Strength, IS 302-1)	-	200	-
22(Construction, IS 302-1)	-	400	-
23.1(Internal Wiring, IS 302-1)	-	200	-
23.2(Internal Wiring, IS 302-1)	-	200	-
23.3(Internal Wiring, IS 302-1)	-	200	-
23.4(Internal Wiring, IS 302-1)	-	200	-
23.5(Internal Wiring, IS 302-1)	-	200	-
23.6(Internal Wiring, IS 302-1)	-	200	-
23.7(Internal Wiring, IS 302-1)	-	200	-
23.8(Internal Wiring, IS 302-1)	-	200	-
23.9(Internal Wiring, IS 302-1)	-	200	-
23.10(Internal Wiring, IS 302-1)	-	200	-
24.1(Components, IS 302-1)	-	100	-
24.2(Components, IS 302-1)	-	100	-
24.5(Components, IS 302-1)	-	100	-
24.6(Components, IS 302-1)	-	100	-
25.1(Supply Connection and External Flexible Cords, IS 302-1)	-	200	-
25.5(Supply Connection and External Flexible Cords, IS 302-1)	-	200	-
25.6(Supply Connection and External Flexible Cords, IS 302-1)	-	200	-
25.7(Supply Connection and External Flexible Cords, IS 302-1)	-	200	-
25.8(Supply Connection and External Flexible Cords, IS 302-1)	-	200	-
26.9(Supply Connection and External Flexible Cords, IS 302-1)	-	200	-
25.1(Supply Connection and External Flexible Cords, IS 302-1)	-	200	-
25.11(Supply Connection and External Flexible Cords, IS 302-1)	-	200	-
25.12(Supply Connection and External Flexible Cords, IS 302-1)	-	200	-
25.13(Supply Connection and External Flexible Cords, IS 302-1)	-	200	-
25.14(Supply Connection and External Flexible Cords, IS 302-1)	-	200	-
25.14(Supply Connection and External Flexible Cords, IS 302-1)	-	200	-
25.15(Supply Connection and External Flexible Cords, IS 302-1)	-	200	-
25.16(Supply Connection and External Flexible Cords, IS 302-1)	-	200	-
25.17(Supply Connection and External Flexible Cords, IS 302-1)	-	200	-
25.18(Supply Connection and External Flexible Cords, IS 302-1)	-	200	-
25.19(Supply Connection and External Flexible Cords, IS 302-1)	-	200	-
25.2(Supply Connection and External Flexible Cords, IS 302-1)	-	200	-
25.21(Supply Connection and External Flexible Cords, IS 302-1)	-	200	-
25.22(Supply Connection and External Flexible Cords, IS 302-1)	-	200	-
26(Terminals for External Conductors, IS 302-1)	-	200	-
27.1(Provision for Earthing, IS 302-1)	-	60	-
27.2(Provision for Earthing, IS 302-1)	-	60	-
27.3(Provision for Earthing, IS 302-1)	-	60	-
27.4(Provision for Earthing, IS 302-1)	-	60	-
27.5(Provision for Earthing, IS 302-1)	-	60	-
28(Screws & Connections, IS 302-1)	-	250	-
29.1(Clearances, Creepage distances and Solid Insulation, IS 302-1)	-	125	-
29.2(Clearances, Creepage distances and Solid Insulation, IS 302-1)	-	125	-
30.1(Resistance to Heat, Fire & Tracking, IS 302-1)	-	250	-
30.2(Resistance to Heat, Fire & Tracking, IS 302-1)	-	250	-
31(Resistance of Rusting, IS 302-1)	-	200	-
32(Radiation, Toxicity and similar Hazard IS 302-1)	-	250	-
17(Overload protection of transformers and associated circuits)	-	250	-
17(Overload protection of transformers and associated circuits)	-	250	-
17(Overload protection of transformers and associated circuits)	-	250	-
18(Endurance)	-	250	-
21.101(Mechanical Strength, IS 302-2-3)	-	400	-
22.101(Construction)	-	400	-
22.102(Construction)	-	400	-
22.103(Construction)	-	400	-
22.104(Construction)	-	400	-
22.105(Construction)	-	400	-
22.106(Construction)	-	400	-
22.107(Construction)	-	400	-
24.4(Components, IS 302-1)	-	100	-
4(General requirement)	-	200	-
16(Leakage current and electric strength)	-	450	-

Complete

23 Jun, 2025

IS 5790 (1985)

Specification for domestic electric cooking ovens (First Revision)

80000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Rating)	-	1000	-
6(Classification)	-	500	-
7(Marking)	-	750	-
8(Protection against Access to Live Parts)	-	1000	-
9(Starting Of Motor Operated Appliances)	-	2000	-
10(Power Input & Current)	-	4000	-
11(Temperature Rise/ Heating)	-	6500	-
12(Operation under overload condition of appliances with heating element)	-	5000	-
13(Electrical Insulation and Leakage Current at Operating Temperature)	-	6500	-
14(Radio and Television Interference Suppressions/ Transient Over Voltage)	-	4000	-
15(Moisture Resistance)	-	4500	-
16(Insulation Resistance and Electric Strength (After Humidity Treatment)/ Leakage Current and Electric Strength)	-	3750	-
17(Overload Protection/ Overload Protection of Transformers & Associated Circuits)	-	1000	-
18(Endurance)	-	5000	-
19(Abnormal Operation)	-	3000	-
20(Stability & Mechanical Hazards)	-	1000	-
21(Mechanical strength)	-	1000	-
22(Construction)	-	2000	-
23(Internal wiring)	-	2000	-
24(Components)	-	1000	-
25(Supply Connection & External Flexible Cords)	-	1000	-
26(Terminals For External Conductors)	-	1000	-
27(Provision For Earthing)	-	2000	-
28(Screws & Connections)	-	2000	-
29(Clearances, Creepage Distances & Solid Insulation)	-	1500	-
30(Resistance to Heat & Fire)	-	5000	-
31(Resistance to Rusting)	-	2500	-
32(Radiation ,Toxicity and similar hazards)	-	1500	-
33(Finish)	-	1000	-
101(Heating Up Time)	-	1500	-
102(Heat Losses)	-	1500	-
103(Uniformity of Temperature)	-	1000	-
104(Thermostat setting and differential (For automatic ovens only))	-	3000	-

Complete

23 Jun, 2025

IS 10322 : Part 5 : Sec 9 (2017)

Luminaires: Part 5 particular requirements: Sec 9 rope lights

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
21.4(General Test Requireements)	-	2000	-
21.5(Classification of Luminaires')	-	1000	-
21.6(Marking)	-	1000	-
21.7(Construction)	-	3000	-
21.8(Creepage Distance and Clearances)	-	1000	-
21.10(Terminals)	-	1000	-
21.11(External & Internal Wiring)	-	1000	-
21.12(Protection against electric shock)	-	2000	-
21.13(Endurance Tests and Thermal Tests)	-	10000	-
21.14(Resistance to Dust & Moisture)	-	10000	-
21.15(Insulation Resistance and Electric Strength)	-	3000	-
21.16(Resistance to Heat , fire and tracking)	-	5000	-

Complete

23 Jun, 2025

IS 10617 (2018)

Hermetic compressors - Specification (Second Revision)

1400000 View breakup
For all type of compressor cooling capacity Upto 0.75 kW- Rs. 7,00,000/- For all type of compressor cooling capacity from 0.75 kW to 2.5 kW - Rs. 9,50,000/- For all type of compressor cooling capacity from 2.5 kW to 5 kW - Rs. 12,50,000/- For all type of compressor cooling capacity from 5 kW to 17.5 kW - Rs. 14,00,000/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1.1 & 5.1 -Table 2, 3, 4,5(Compressor Performance Test & Compressor Capacity Rating Test)	-	468000	-
Cl. 4 of IS:10617:2018(10617)	-	2000	-
Cl. 5,5.1 of IS:10617:2018(10617)	-	3000	-
Cl.6.1.1 of IS:10617:2018(10617)	-	468000	-
Cl. 6.1.2, 6.1.2.1 of IS:10617:2018(10617)	-	5000	-
Cl. 6.1.2.2 of IS:10617:2018(10617)	-	25000	-
Cl. 6.1.2.3 of IS:10617:2018(10617)	-	25000	-
Cl. 6.1.2.4 of IS:10617:2018(10617)	-	25000	-
Cl. 6.1.3 of IS:10617(10617)	-	20000	-
Cl. 6.1.4 of IS:10617:2018(10617)	-	5000	-
Cl. 6.1.5 of IS:10617:2018(10617)	-	5000	-
Cl. 6.1.6 of IS:10617:2018(10617)	-	20000	-
Cl. 6.1.7 of IS:10617:2018(10617)	-	25000	-
Cl. 6.2 of IS:10617:2018(10617)	-	30000	-
Cl. 7, 7.1 of IS:10617:2018(10617)	-	30000	-
Cl. 8, 8.1, 8.2, 8.3, 8.4, 8.5 of IS:10617:2018(10617)	-	200000	-
Cl. 9 of IS:10617-2018(10617)	-	5000	-
Cl. 10 of IS:10617-2018(10617)	-	2000	-
Cl. 11, 11.1, 11.2, 11.2.1 of IS:10617-2018(10617)	-	5000	-

Complete

23 Jun, 2025

Single phase- LBP/MBP/HBP -Cooling capacity upto 17.5 kW Three phase- LBP/MBP/HBP- Cooling capacity upto 17.5 kW DC- LBP/MBP/HBP- Cooling capacity upto 17.5 kW

IS 1258 (2005)

Bayonet lamp holders (Fourth Revision)

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Rating )	-	400	-
6(Rating )	-	400	-
7(Classification)	-	500	-
7.2(Classification)	-	100	-
7.3(Classification)	-	100	-
7.4(Classification)	-	100	-
7.5(Classification)	-	100	-
7.6(Classification)	-	100	-
9.1(Dimensions)	-	500	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.2(Dimensions)	-	150	-
9.3(Dimensions)	-	150	-
9.3(Dimensions)	-	150	-
9.3(Dimensions)	-	150	-
9.3(Dimensions)	-	150	-
9.3(Dimensions)	-	150	-
9.3(Dimensions)	-	150	-
9.3(Dimensions)	-	150	-
10(Protection against electric shock )	-	1000	-
11.1(Terminals)	-	125	-
11.2(Terminals)	-	125	-
11.3(Terminals)	-	125	-
11.3(Terminals)	-	125	-
11.3(Terminals)	-	125	-
11.3(Terminals)	-	125	-
11.3(Terminals)	-	125	-
11.3(Terminals)	-	125	-
11.4(Terminals)	-	125	-
12(Provision for Earthing)	-	1000	-
13.1(Construction)	-	110	-
13.1(Construction (Data Sheet No 7005-10))	-	110	-
13.1(Construction (Data Sheet No 7005-10& 7006-15A))	-	110	-
13.2(Construction (Data Sheet No 7005-10& 7006-15A))	-	110	-
13.3(Construction )	-	110	-
13.4(Construction )	-	110	-
13.5(Construction)	-	110	-
13.2 ,13.6 & 13.7 (Construction)	-	110	-
13.2 ,13.6 & 13.8(Construction)	-	110	-
13.11(Construction)	-	110	-
14(Construction)	-	500	-
15.1(Moisture Resistance, Insulation Resistance and Electric Strength)	-	700	-
15.2(Moisture Resistance, Insulation Resistance and Electric Strength)	-	700	-
15.3(Moisture Resistance, Insulation Resistance and Electric Strength)	-	700	-
16.1(Mechanical Strength)	-	500	-
16.1(Mechanical Strength)	-	60	-
16.2(Mechanical Strength)	-	60	-
16.3(Mechanical Strength)	-	60	-
16.4(Mechanical Strength)	-	60	-
16.5(Mechanical Strength)	-	60	-
16.6 & Table - 6(Mechanical Strength)	-	60	-
16.7(Mechanical Strength)	-	60	-
16.8(Mechanical Strength)	-	60	-
17(Screws,current-carrying parts and connections)	-	500	-
18(Creepage distances and Clearances)	-	500	-
18.1, Table 8(Creepage distances and Clearances)	-	500	-
18.1, Table 8(Creepage distances and Clearances)	-	500	-
18.1, Table 8(Creepage distances and Clearances)	-	500	-
18.1, Table 8(Creepage distances and Clearances)	-	500	-
18.1, Table 8(Creepage distances and Clearances)	-	500	-
18.1, Table 8(Creepage distances and Clearances)	-	500	-
18.1, Table 8(Creepage distances and Clearances)	-	500	-
19.1(General resistance to heat)	-	375	-
19.2(General resistance to heat)	-	375	-
19.3(General resistance to heat)	-	375	-
19.4(Resistance to heat test)	-	375	-
20.1(Resistance to heat, fire and tracking)	-	500	-
20.3(Resistance to heat, fire and tracking)	-	500	-
20.4(Resistance to heat, fire and tracking)	-	500	-
20.5(Resistance to tracking)	-	500	-
21.1(Resistance to excessive residual stresses and to rusting)	-	500	-
21.1(Resistance to excessive residual stresses and to rusting)	-	500	-
6(Rating )	-	400	-
6(Rating )	-	400	-
7(Classification)	-	500	-
7.2(Classification)	-	100	-
7.3(Classification)	-	100	-
7.4(Classification)	-	100	-
7.5(Classification)	-	100	-
7.6(Classification)	-	100	-
8.1(Marking )	-	500	-
8.1(Marking )	-	60	-
8.1(Marking )	-	60	-
8.1(Marking )	-	60	-
8.1(Marking )	-	60	-
8.1(Marking )	-	60	-
8.1(Marking )	-	60	-
8.1(Marking )	-	60	-
8.1(Marking )	-	60	-
8.1(Marking )	-	60	-
8.1(Marking )	-	60	-
8.1(Marking )	-	60	-
8.2(Marking )	-	60	-
8.2(Marking )	-	60	-
8.2(Marking )	-	60	-
8.3(Marking )	-	60	-
8.4(Marking )	-	60	-
8.5(Marking )	-	60	-
8.6(Marking )	-	60	-
8.7(Marking )	-	60	-
8.8(Marking )	-	60	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.1(Dimensions)	-	150	-
9.2(Dimensions)	-	150	-
9.3(Dimensions)	-	150	-
9.3(Dimensions)	-	150	-
9.3(Dimensions)	-	150	-
9.3(Dimensions)	-	150	-
9.3(Dimensions)	-	150	-
9.3(Dimensions)	-	150	-
10(Protection against electric shock )	-	1000	-
11.1(Terminals)	-	125	-
11.2(Terminals)	-	125	-
11.3(Terminals)	-	125	-
12.3(Terminals)	-	125	-
11.3(Terminals)	-	125	-
11.3(Terminals)	-	125	-
11.3(Terminals)	-	125	-
11.4(Terminals)	-	125	-
13.1(Construction)	-	110	-
13.1(Construction (Data Sheet No 7005-10))	-	110	-
13.1(Construction (Data Sheet No 7005-10& 7006-15A))	-	100	-
13.2(Construction (Data Sheet No 7005-10& 7006-15A))	-	110	-
13.3(Construction )	-	110	-
13.4(Construction )	-	110	-
13.5(Construction)	-	110	-
13.2 ,13.6 & 13.7 (Construction)	-	110	-
13.2 ,13.6 & 13.8(Construction)	-	110	-
13.11(Construction)	-	110	*
14(Construction)	-	500	-
15.1(Moisture Resistance, Insulation Resistance and Electric Strength)	-	700	-
15.3(Moisture Resistance, Insulation Resistance and Electric Strength)	-	700	-
16.1(Mechanical Strength)	-	60	-
16.2(Mechanical Strength)	-	60	-
16.4(Mechanical Strength)	-	60	-
16.5(Mechanical Strength)	-	60	-
16.6 & Table - 6(Mechanical Strength)	-	60	-
16.7(Mechanical Strength)	-	60	-
16.8(Mechanical Strength)	-	60	-
17(Screws,current-carrying parts and connections)	-	500	-
18(Creepage distances and Clearances)	-	500	-
18(Creepage distances and Clearances)	-	500	-
18(Creepage distances and Clearances)	-	500	-
18(Creepage distances and Clearances)	-	500	-
18(Creepage distances and Clearances)	-	500	-
18(Creepage distances and Clearances)	-	500	-
18(Creepage distances and Clearances)	-	500	-
18(Creepage distances and Clearances)	-	500	-
19.1(General resistance to heat)	-	375	-
19.2(General resistance to heat)	-	375	-
19.3(General resistance to heat)	-	375	-
19.4(Resistance to heat test)	-	500	-
20.1(Resistance to heat, fire and tracking)	-	500	-
20.3(Resistance to heat, fire and tracking)	-	500	-
20.4(Resistance to heat, fire and tracking)	-	500	-
20.5(Resistance to tracking)	-	500	-
21.1(Resistance to excessive residual stresses and to rusting)	-	500	-
21.1(Resistance to excessive residual stresses and to rusting)	-	500	-

Complete

23 Jun, 2025

IS 555 (1979)

Specification for electric table type fans and regulators (Third Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.0(Size, Speed and Types)	-	300	-
4.0(Rated Voltages)	-	400	-
5.0(Rated Frequency)	-	1000	-
6.0(Design and General Construction)	-	300	-
7.8(Speed Regulators)	-	200	-
7.9(Interchangeability)	-	300	-
7.11(Oscillating Mechanism)	-	500	-
9.0(Marking)	-	300	-
10.3(Air Delivery Test)	-	1700	-
10.4(Temperature-Rise Test)	-	1000	-
10.5(Leakage Current)	-	800	-
10.6(High Voltage Test)	-	1300	-
10.7(Insulation-Resistance Test (Shall follow Moisture Resistance Test Cl.10.12))	-	900	-
10.8(Construction)	-	900	-
10.9(Fan Speed and Input)	-	400	-
10.1(Earthing Connection)	-	800	-
10.11(Protection against Electric Shock)	-	500	-
10.12(Moisture Resistance Test)	-	1500	-
10.13, 7.4(Mechanical Endurance Test (for Regulators Only))	-	1100	-
10.14(Cord Grip Test)	-	400	-
10.16(Creepage Distances and Clearances)	-	400	-

Complete

23 Jun, 2025

IS 11037 (2019)

Electronic Type Fan Regulators — Specification ( First Revision )

36000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.1 (a)(Marking )	-	83	-
9.1 (b)(Marking )	-	83	-
9.1 (c)(Marking )	-	83	-
9.1 (d)(Marking )	-	83	-
9.1 (e)(Marking )	-	83	-
9.1 (f)(Marking )	-	83	-
9.2(Marking )	-	500	-
6.1(Design and General Construction)	-	200	-
6.2(Design and General Construction)	-	200	-
6.3(Design and General Construction)	-	200	-
6.5(Design and General Construction)	-	200	-
6.6(Design and General Construction)	-	200	-
9.5.1 , 7.3(Temperature Rise)	-	1500	-
9.5.1 , 7.3 (a)(Temperature Rise )	-	750	-
9.5.1 , 7.3 (b)(Temperature Rise)	-	750	-
9.5.1 , 7.3 (b)(Temperature Rise)	-	750	-
9.5.1 , 7.3 (b)(Temperature Rise)	-	750	-
9.5.2, 7.2(Leakage Current Test(as per Cl.13.2 of IS 302 (Part 1).)	-	1000	-
9.5.3(High Voltage Test)	-	1500	-
9.5.5(Earthing Connection)	-	1000	-
9.5.6(Protection against electric shock (as per Cl.8 of IS 302 (Part 1))	-	1000	-
7.6(General and safety requirements)	-	1000	-
7.7(Voltage drop)	-	1100	-
8.1(Performance)	-	300	-
8.2(Performance)	-	300	-
8.3(Performance)	-	300	-
9.5.7, 9.5.4(Moisture Resistance )	-	2500	-
7.4.1(a)(Mechanical strength )	-	500	-
7.4.1(b)(Mechanical strength )	-	500	-
9.5.8, (Mechanical strength (as per Cl.21.1 of IS 302-1:2008))	-	1500	-
9.5.9, 7.5, Table-1(Creepage Distances and Clearances (as per Cl. 29 of IS 302-1))	-	1000	-
9.5.9, 7.5, Table-1(Creepage Distances and Clearances (as per Cl. 29 of IS 302-1))	-	1000	-
9.5.10( Electrical Endurance Test)	-	3000	-
9.5.11.2(Environmental Tests)	-	5000	-
9.5.11.3(Environmental Tests)	-	3000	-
9.5.11.4(Environmental Tests)	-	4000	-
9.5.12(Resistance to Abnormal Heat and to Fire)	-	750	-
9.5.12.1(Resistance to Abnormal Heat and to Fire)	-	750	-
9.5.13(Resistance to Rusting )	-	1500	-
9.5.14(Checking of Dimensions)	-	1500	-
9.1(Marking )	-	500	-
9.1 (a)(Marking )	-	83	-
9.1 (b)(Marking )	-	83	-
9.1 (c)(Marking )	-	83	-
9.1 (d)(Marking )	-	83	-
9.1 (e)(Marking )	-	83	-
9.1 (f)(Marking )	-	83	-
9.2(Marking )	-	83	-
6.1(Design and General Construction)	-	200	-
6.2(Design and General Construction)	-	200	-
6.3(Design and General Construction)	-	200	-
6.5(Design and General Construction)	-	200	-
6.6(Design and General Construction)	-	200	-
9.5.1 , 7.3(Temperature Rise)	-	1500	-
9.5.1 , 7.3 (a)(Temperature Rise )	-	750	-
9.5.1 , 7.3 (b)(Temperature Rise)	-	750	-
9.5.1 , 7.3 (b)(Temperature Rise)	-	750	-
9.5.1 , 7.3 (b)(Temperature Rise)	-	750	-
9.5.2, 7.2(Leakage Current Test(as per Cl.13.2 of IS 302 (Part 1).)	-	1000	-
9.5.5(Earthing Connection)	-	1000	-
9.5.6(Protection against electric shock (as per Cl.8 of IS 302 (Part 1))	-	1000	-
7.6(General and safety requirements)	-	1000	-
8.1(Performance)	-	300	-
8.2(Performance)	-	300	-
8.3(Performance)	-	300	-
9.5.7, 9.5.4(Moisture Resistance )	-	2500	-
7.4.1(Mechanical strength )	-	1000	-
7.4.1(a)(Mechanical strength )	-	500	-
7.4.1(b)(Mechanical strength )	-	500	-
9.5.8, (Mechanical strength (as per Cl.21.1 of IS 302-1:2008))	-	1500	-
9.5.9, 7.5, Table-1(Creepage Distances and Clearances (as per Cl. 29 of IS 302-1))	-	1000	-
9.5.9, 7.5, Table-1(Creepage Distances and Clearances (as per Cl. 29 of IS 302-1))	-	1000	-
9.5.10( Electrical Endurance Test)	-	3000	-
9.5.11.3(Environmental Tests)	-	3000	-
9.5.11.4(Environmental Tests)	-	4000	-
9.5.12(Resistance to Abnormal Heat and to Fire)	-	750	-
9.5.12.1(Resistance to Abnormal Heat and to Fire)	-	750	-
9.5.13(Resistance to Rusting )	-	1500	-

Complete

23 Jun, 2025

IS 11328 (1985)

Specification for self - Contained automatic ice makers

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.5.1(Pressure Test and leakage tests)	-	5500	-
5.5.2(Insulation resistance test)	-	6250	-
5.5.3(High voltage test)	-	5000	-
5.5.4(Ice making capacity rating test)	-	8250	-

Complete

23 Jun, 2025

IS 15750 (2006)

Household frost - Free refrigerating appliances - Refrigerators cooled by internal forced air circulation - Characteristics and test methods - Specification

150000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.3(General Definitions)	-	500	-
4(Material Design & manufacturing)	-	600	-
5(Required characteristics)	-	500	-
6(Determination of linear dimensions, volumes and areas)	-	15000	-
7(General test condition)	-	600	-
8(Testing the air tightness of Door or Lid Seal)	-	7000	-
9(Testing the opening force of door(s) or lid(s))	-	3500	-
10(Testing the durability of hinges and handles of door(s) and lid(s))	-	3500	-
11(Testing the mechanical strength of shelves and similar components)	-	7000	-
12(Testing the storage temperatures)	-	10000	-
13(Water vapour condensation test )	-	7000	-
14(Energy consumption test)	-	40000	-
15(Temperature Rise Test)	-	10000	-
16(Pull down test)	-	25000	-
17(Ice making test)	-	5000	-
18(Test for absence of odour & taste)	-	3000	-
19(High voltage test)	-	3000	-
20(Insulation resistance test)	-	3000	-
22(Requirement of ECO mark)	-	4600	-
23(Designation)	-	600	-
24(Marking)	-	600	-

Complete

23 Jun, 2025

IS 1476 : Part 1 (2000)

Performance of household refrigerating appliance - Refrigerators with or without low temperature compartment: Part 1 energy consumption and performance (Third Revision)

135000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Classification)	-	500	-
5(Material Design & Manufacture)	-	3000	-
6(Electrical Components)	-	2500	-
7.1(Dimensional characteristics)	-	250	-
7.2(Performance Characteristics)	-	250	-
8(Determination of Linear dimensions, volumes & areas.)	-	12000	-
9(Operational requirement)	-	500	-
11( Additional Requirement for ECO mark)	-	500	-
13(Measurement)	-	500	-
14.1(Door Seal Test)	-	5000	-
14.2(Mechanical strength of shelves & similar components)	-	6000	-
14.3(Doors and fitting test)	-	5000	-
14.4(No load adjustment test)	-	10000	-
14.5(No-load performance Test)	-	22000	-
14.6(Ice making test)	-	13000	-
14.7(Thermal Insulation Test)	-	5500	-
14.8(High voltage test)	-	5000	-
14.9(Rated Energy consumption test)	-	34500	-
15.1(Thermostat Test)	-	5000	-
15.2(Insulation resistance)	-	4000	-

Complete

23 Jun, 2025

IS 1474 (1959)

Specification for commercial refrigerators

285000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.3.1(Gross Volume)	-	7000	-
3.3(Volume of evaporator space)	-	7000	-
3.5(Volume of fixed shelves and partitions)	-	7000	-
3.6(Computation of shelf area)	-	7000	-
3.7(Net volume)	-	7000	-
7.5.1(Pressure Test)	-	35000	-
7.5.7(Test for Adequate Rating of Compressor Motor)	-	25000	-
7.5.6(Rating Test)	-	40000	-
7.5.5(Condensation Test)	-	50000	-
7.5.4(Thermal Insulation Test)	-	25000	-
7.5.3(Insulation Resistance Test (Assembly Test))	-	40000	-
7.5.8(Door Seal Test)	-	35000	-

Complete

23 Jun, 2025

IS 1287 (1993)

Electric toasters - Specification (Third Revision)

38000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Rating)	-	600	-
7(Classification)	-	650	-
8(Marking)	-	750	-
9(Safety Requirements)	-	0	-
11(Overall dimension)	-	1500	-
12(Length of the Flexible cord)	-	750	-
13(Mass)	-	750	-
14(Number and Dimensions of the toasing chambers, toasting surfaces and heating elements)	-	5000	-
15(Force necessary to operate the bread carriage)	-	5000	-
16(Preparation of bread for toasters)	-	1000	-
17(Browning control setting)	-	5000	-
18(Toasting)	-	2000	-
19(Toasting time)	-	2000	-
20(Evenness of Browning)	-	3000	-
21(Browning control characteristic)	-	3000	-
22(Endurance)	-	5000	-
23(Finish)	-	1000	-
24(Functional Provision)	-	1000	-

Complete

23 Jun, 2025

IS/IEC 61730 : PART 1 (2004)

Photovoltaic (PV) Module Safety Qualification Part 1 Requirements for Construction

460000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Application classes)	-	20000	-
4(Construction requirements)	-	20000	-
5(Polymeric materials)	-	45000	-
6(Internal wiring and current-carrying parts)	-	45000	-
7(Connections)	-	95000	-
8(Bonding and grounding)	-	35000	-
9(Creepage and clearance distances)	-	35000	-
10(Field wiring compartments with covers)	-	60000	-
11(Marking)	-	15000	-
12()	-	40500	-

Complete

23 Jun, 2025

Bureau of Indian Standards

The National Standards Body of India

DELHI TEST HOUSE KUNDLI

PLOT NO 50 phase IV sector 57 hsiidc industrial area kundli, Sonipat, Sonipat, Haryana, 131028

9810442016 ag@delhitesthouse.com

Scope List