BIS - LIMS (Laboratory Information Management System)

DELHI TEST HOUSE, Azadhpur

A-62/3, G T KARNAL ROAD INDUSTRIAL AREA, OPPOSITE HANS CINEMA, AZADPUR, DELHI 110033, Delhi, North, Delhi, 110033

9810442016 info@delhitesthouse.com

Scope List

Reset

204 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 736 (1986)

Specification for wrought aluminium and aluminium alloy plate for general engineering purposes (Third Revision)

ALL

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Freedom from defect)	-	500	-
5(chemical composition)	-	4500	-
6.1 table 2(0.2% proof strength)	-	1700	-
6.1 table 2(tensile strength)	-	1700	-
6.1 table 2(Elongation)	-	1700	-
8(Dimensions & Tolerances)	-	2000	-
5.1, Table 1(Aluminium)	-	500	-
5.1, Table 1(Copper)	-	500	-
5.1, Table 1(Magnesium)	-	500	-
5.1, Table 1(Silicon)	-	500	-
5.1, Table 1(Iron)	-	500	-
5.1, Table 1(Mangnese)	-	500	-
5.1, Table 1(Zinc)	-	500	-
5.1, Table 1(Titanium and /or other grain refining element)	-	500	-
5.1, Table 1(Chromium)	-	500	-
5.1, Table 1(Vanadium)	-	500	-

17 Jun, 2027

-
Included w.e.f. 03.03.2025

IS 740 (1977)

Specification for wrought aluminium and aluminium alloy rivet stock for general engineering purposes (Second Revision)

ALL

9500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1, Table 1of IS:740 (Designation & Condition 65032, 'W')(Tensile Strength of Size upto and including 25 mm)	-	2000	NA
4.1, Table 1of IS:740 (Designation & Condition 64430, 'W')(Tensile Strength of Size upto and including 25 mm)	-	2000	NA
4.1, Table 1of IS:740 (Designation & Condition 55000, 'OD')(Tensile Strength of Size upto and including 25 mm)	-	2000	NA
4.1, Table 1of IS:740 (Designation & Condition 55000, 'O or M')(Tensile Strength of Size upto and including 25 mm)	-	2000	NA
4.1, Table 1of IS:740 (Designation & Condition 53000, 'OD')(Tensile Strength of Size upto and including 25 mm)	-	2000	NA
4.1, Table 1of IS:740 (Designation & Condition 53000, 'O or M')(Tensile Strength of Size upto and including 25 mm)	-	2000	NA
4.1, Table 1of IS:740 (Designation & Condition 24345, 'W')(Tensile Strength of Size upto and including 12 mm)	-	2000	NA
4.1, Table 1of IS:740 (Designation & Condition 19000, '112')(Tensile Strength of Size upto and including 12 mm)	-	2000	NA
4.1, Table 1of IS:740 (Designation 65032)(Aluminium)	-	500	NA
4.1, Table 1of IS:740 (Designation 65032)(Either Cr or Mn shall present)	-	500	NA
4.1, Table 1of IS:740 (Designation 65032)(Chromium)	-	500	NA
4.1, Table 1of IS:740 (Designation 65032)(Titanium and or other grain refining elements)	-	500	NA
4.1, Table 1of IS:740 (Designation 65032)(Zinc)	-	500	NA
4.1, Table 1of IS:740 (Designation 65032)(Manganese)	-	500	NA
4.1, Table 1of IS:740 (Designation 65032)(Iron)	-	500	NA
4.1, Table 1of IS:740 (Designation 65032)(Silicon)	-	500	NA
4.1, Table 1of IS:740 (Designation 65032)(Magnesium)	-	500	NA
4.1, Table 1of IS:740 (Designation 65032)(Copper)	-	500	NA
4.1, Table 1of IS:740 (Designation 64430)(Aluminium)	-	500	NA
4.1, Table 1of IS:740 (Designation 64430)(Cr+Mn)	-	500	NA
4.1, Table 1of IS:740 (Designation 64430)(Chromium)	-	500	NA
4.1, Table 1of IS:740 (Designation 64430)(Titanium and or other grain refining elements)	-	500	NA
4.1, Table 1of IS:740 (Designation 64430)(Zinc)	-	500	NA
4.1, Table 1of IS:740 (Designation 64430)(Manganese)	-	500	NA
4.1, Table 1of IS:740 (Designation 64430)(Iron)	-	500	NA
4.1, Table 1of IS:740 (Designation 64430)(Silicon)	-	500	NA
4.1, Table 1of IS:740 (Designation 64430)(Magnesium)	-	500	NA
4.1, Table 1of IS:740 (Designation 64430)(Copper)	-	500	NA
4.1, Table 1of IS:740 (Designation 55000)(Aluminium)	-	500	NA
4.1, Table 1of IS:740 (Designation 55000)(Cr+Mn)	-	2000	NA
4.1, Table 1of IS:740 (Designation 55000)(Chromium)	-	500	NA
4.1, Table 1of IS:740 (Designation 55000)(Titanium and or other grain refining elements)	-	500	NA
4.1, Table 1of IS:740 (Designation 55000)(Zinc)	-	500	NA
4.1, Table 1of IS:740 (Designation 55000)(Manganese)	-	500	NA
4.1, Table 1of IS:740 (Designation 55000)(Iron)	-	500	NA
4.1, Table 1of IS:740 (Designation 55000)(Silicon)	-	500	NA
4.1, Table 1of IS:740 (Designation 55000)(Magnesium)	-	500	NA
4.1, Table 1of IS:740 (Designation 55000)(Copper)	-	500	NA
4.1, Table 1of IS:740 (Designation 53000)(Aluminium)	-	500	NA
4.1, Table 1of IS:740 (Designation 53000)(Cr+Mn)	-	2000	NA
4.1, Table 1of IS:740 (Designation 53000)(Chromium)	-	500	NA
4.1, Table 1of IS:740 (Designation 53000)(Titanium and or other grain refining elements)	-	500	NA
4.1, Table 1of IS:740 (Designation 53000)(Zinc)	-	500	NA
4.1, Table 1of IS:740 (Designation 53000)(Manganese)	-	500	NA
4.1, Table 1of IS:740 (Designation 53000)(Iron)	-	500	NA
4.1, Table 1of IS:740 (Designation 53000)(Silicon)	-	500	NA
4.1, Table 1of IS:740 (Designation 53000)(Magnesium)	-	500	NA
4.1, Table 1of IS:740 (Designation 53000)(Copper)	-	500	NA
4.1, Table 1of IS:740 (Designation 24345)(Aluminium)	-	500	NA
4.1, Table 1of IS:740 (Designation 24345)(Chromium)	-	500	NA
4.1, Table 1of IS:740 (Designation 24345)(Titanium and or other grain refining elements)	-	500	NA
4.1, Table 1of IS:740 (Designation 24345)(Zinc)	-	500	NA
4.1, Table 1of IS:740 (Designation 24345)(Manganese)	-	500	NA
4.1, Table 1of IS:740 (Designation 24345)(Iron)	-	500	NA
4.1, Table 1of IS:740 (Designation 24345)(Silicon)	-	500	NA
4.1, Table 1of IS:740 (Designation 24345)(Magnesium)	-	500	NA
4.1, Table 1of IS:740 (Designation 24345)(Copper)	-	500	NA
4.1, Table 1of IS:740 (Designation 19000)(Cu+Mg+Si+Fe+Mn+Zn)	-	2000	NA
4.1, Table 1of IS:740 (Designation 19000)(Aluminium)	-	500	NA
4.1, Table 1of IS:740 (Designation 19000)(Zinc)	-	500	NA
4.1, Table 1of IS:740 (Designation 19000)(Manganese)	-	500	NA
4.1, Table 1of IS:740 (Designation 19000)(Iron)	-	500	NA
4.1, Table 1of IS:740 (Designation 19000)(Silicon)	-	500	NA
4.1, Table 1of IS:740 (Designation 19000)(Magnesium)	-	500	NA
4.1, Table 1of IS:740 (Designation 19000)(Copper)	-	500	NA
6(Freedom From Defects)	-	500	NA
7(Dmension And Tolerances)	-	2000	NA
9.2(Head Forming Test)	-	1500	NA
11(Marking)	-	250	NA

17 Jun, 2027

-
Included w.e.f. 03.03.2025

IS 734 (1975)

Specification for wrought aluminium and aluminium alloy forging stock and forgings (For General Engineering Purposes) (Second Revision)

ALL

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1 table 2(0.2% proof strength)	-	2000	COMPLETE TESTING - 10000
5.1 table 2(Tensile strength)	-	2000	COMPLETE TESTING - 10000
5.1 table 2(Elongation)	-	1000	COMPLETE TESTING - 10000
Cl.5.1(Aluminium - IS 504 and its parts or any other intrumental/chemical methods)	-	500	COMPLETE TESTING - 10000
Cl.5.1(Copper - IS 504 and its parts or any other intrumental/chemical methods)	-	500	COMPLETE TESTING - 10000
Cl.5.1(Magnesium - IS 504 and its parts or any other intrumental/chemical methods)	-	500	COMPLETE TESTING - 10000
Cl.5.1(Silicon - IS 504 and its parts or any other intrumental/chemical methods)	-	500	COMPLETE TESTING - 10000
Cl.5.1(Iron - IS 504 and its parts or any other intrumental/chemical methods)	-	500	COMPLETE TESTING - 10000
Cl.5.1(Manganese - IS 504 and its parts or any other intrumental/chemical methods)	-	500	COMPLETE TESTING - 10000
Cl.5.1(Zinc - IS 504 and its parts or any other intrumental/chemical methods)	-	500	COMPLETE TESTING - 10000
Cl.5.1(Titanium And/or Other Grain Refining Elements - IS 504 and its parts or any other intrumental/chemical methods)	-	500	COMPLETE TESTING - 10000
Cl.5.1(Chromium - IS 504 and its parts or any other intrumental/chemical methods)	-	500	COMPLETE TESTING - 10000
Cl.5.1(Remarks (Cu + Mg + Si + Fe + Mn + Zn) - IS 504 and its parts or any other intrumental/chemical methods)	-	3000	COMPLETE TESTING - 10000
4.1(Freedom from defects)	-	250	COMPLETE TESTING - 10000
9.1(Tensile test)	-	2000	COMPLETE TESTING - 10000
5.1 table 1(chemical composition)	-	5000	COMPLETE TESTING - 10000

17 Jun, 2027

-
Included w.e.f. 03.03.2025

IS 1285 (2023)

WROUGHT ALUMINIUM AND ALUMINIUM ALLOYS EXTRUDED ROUND TUBE AND HOLLOW SECTIONS FOR GENERAL ENGINEERINGPURPOSES SPECIFICATION

ALL

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8("Dimensions and tolerances of the material shall be as laid down in the Indian Standards indicated below: a) Extruded round tube IS 2673; and b) Extruded hollow sections IS 6477.")	-	500	-
10(Tensile test)	-	2000	-
Cl.9.1(Aluminium- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Copper- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Magnesium- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Silicon- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Iron- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Manganese- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Zinc- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Titanium and/ or other grain refining elements- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Chromium- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Remarks (Ti+V) - IS 504 and its parts or any other intrumental/chemical methods)	-	1000	-
Cl.9.1(Remarks (Cr+Mn) - IS 504 and its parts or any other intrumental/chemical methods)	-	1000	-
Cl.9.1(Remarks (Total Impurities)- IS 504 and its parts or any other intrumental/chemical methods)	-	5000	-
6.1("The extruded round tube and hollow sections shall be sound and visually free from harmful defects. ")	-	0	-
6.2(Slight discoloration due to heat treatment, minor polishing marks and spiral marks due to roll straightening shall not be a cause for rejection.)	-	0	-
9(" Extruded round tubes and hollow sections shall be made from alloys specified in IS 733. 9.2 The chemical analysis of the material shall be carried out either in accordance with the methods specified in IS 504 (Part 1 to 12) and IS 504 (Part 13 to 16) or by any other established instrumental/chemical method. In case of any dispute the method specified in relevant parts of IS 504 shall be used as referee method. However, when the method is not given in IS 504, the referee method shall be as agreed to between the purchaser and the manufacturer. ")	-	0	-
8("Dimensions and tolerances of the material shall be as laid down in the Indian Standards indicated below: a) Extruded round tube IS 2673; and b) Extruded hollow sections IS 6477.")	-	-	-
10(Tensile test)	-	-	-
Cl.9.1(Aluminium- IS 504 and its parts or any other intrumental/chemical methods)	-	-	-
Cl.9.1(Copper- IS 504 and its parts or any other intrumental/chemical methods)	-	-	-
Cl.9.1(Magnesium- IS 504 and its parts or any other intrumental/chemical methods)	-	-	-
Cl.9.1(Silicon- IS 504 and its parts or any other intrumental/chemical methods)	-	-	-
Cl.9.1(Iron- IS 504 and its parts or any other intrumental/chemical methods)	-	-	-
Cl.9.1(Manganese- IS 504 and its parts or any other intrumental/chemical methods)	-	-	-
Cl.9.1(Zinc- IS 504 and its parts or any other intrumental/chemical methods)	-	-	-
Cl.9.1(Titanium and/ or other grain refining elements- IS 504 and its parts or any other intrumental/chemical methods)	-	-	-
Cl.9.1(Chromium- IS 504 and its parts or any other intrumental/chemical methods)	-	-	-
Cl.9.1(Remarks (Ti+V) - IS 504 and its parts or any other intrumental/chemical methods)	-	-	-
Cl.9.1(Remarks (Cr+Mn) - IS 504 and its parts or any other intrumental/chemical methods)	-	-	-
Cl.9.1(Remarks (Total Impurities)- IS 504 and its parts or any other intrumental/chemical methods)	-	-	-
6.1("The extruded round tube and hollow sections shall be sound and visually free from harmful defects. ")	-	-	-
6.2(Slight discoloration due to heat treatment, minor polishing marks and spiral marks due to roll straightening shall not be a cause for rejection.)	-	-	-
9(" Extruded round tubes and hollow sections shall be made from alloys specified in IS 733. 9.2 The chemical analysis of the material shall be carried out either in accordance with the methods specified in IS 504 (Part 1 to 12) and IS 504 (Part 13 to 16) or by any other established instrumental/chemical method. In case of any dispute the method specified in relevant parts of IS 504 shall be used as referee method. However, when the method is not given in IS 504, the referee method shall be as agreed to between the purchaser and the manufacturer. ")	-	-	-

17 Jun, 2027

-
-

IS 739 (1992)

Wrought aluminium and aluminium alloys - Wire for general engineering purposes - Specification (Third Revision)

ALL

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.0(Freedom from defects)	-	500	COMPLETE TESTING CHARGES - 12500/-
7.0(Dimension and Tolerances)	-	500	COMPLETE TESTING CHARGES - 12500/-
8.1 Table-1(Al)	-	500	COMPLETE TESTING CHARGES - 12500/-
8.1 Table-1(Cu)	-	500	COMPLETE TESTING CHARGES - 12500/-
8.1 Table-1(Mg)	-	500	COMPLETE TESTING CHARGES - 12500/-
8.1 Table-1(Si)	-	500	COMPLETE TESTING CHARGES - 12500/-
8.1 Table-1(Fe)	-	500	COMPLETE TESTING CHARGES - 12500/-
8.1 Table-1(Mn)	-	500	COMPLETE TESTING CHARGES - 12500/-
8.1 Table-1(Zn)	-	500	COMPLETE TESTING CHARGES - 12500/-
8.1 Table-1(Ti)	-	500	COMPLETE TESTING CHARGES - 12500/-
8.1 Table-1(Cr)	-	500	COMPLETE TESTING CHARGES - 12500/-
9.1(Tensile Strength)	-	5000	COMPLETE TESTING CHARGES - 12500/-
9.3(Wrapping Test)	-	1500	COMPLETE TESTING CHARGES - 12500/-
10(Selection of Test Samples)	-	0	COMPLETE TESTING CHARGES - 12500/-
10(Selection of Test Samples)	-	0	COMPLETE TESTING CHARGES - 12500/-
10(Selection of Test Samples)	-	0	-
10(Selection of Test Samples)	-	0	-
10(Selection of Test Samples)	-	-	-

17 Jun, 2027

-
Included .w.e.f.03.03.2025

IS 17782 (2021)

FORTIFIED RICE KERNELS-SPECIFICATION

45000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Description)	-	500	-
4.1.1(length, breadth, and thickness)	-	1500	-
4.1.2(length, breadth, thickness, thousand kernel weight, and true density)	-	1000	-
4.1.6(ree from added colouring matter, metal peices and other impurities)	-	1000	-
Table-1, (4.1.3, 4.1.5 and 8)(i) Iron, mg/100 g)	-	2000	-
Table-1, (4.1.3, 4.1.5 and 8)(ii) Folic acid, μg/100 g)	-	2000	-
Table-1, (4.1.3, 4.1.5 and 8)(iii) Vitamin B12, μg/100 g)	-	2000	-
Table-2, 4.1.4, 4.1.5 and 8(i) Zinc, mg/100 g)	-	2000	-
Table-2, 4.1.4, 4.1.5 and 8(ii) Vitamin A, μg/100 g)	-	2000	-
Table-2, 4.1.4, 4.1.5 and 8(iii) Thiamine)	-	2500	-
Table-2, 4.1.4, 4.1.5 and 8(iv) Riboflavin (Vitamin B2), mg/100 g)	-	2500	-
Table-2, 4.1.4, 4.1.5 and 8(v) Niacin (Vitamin B3), mg/100 g)	-	2500	-
Table-2, 4.1.4, 4.1.5 and 8(vi) Pyridoxine (Vitamin B6), mg/100 g)	-	2500	-
Table-3, 4.1.6 and 8(i) Moisture content,)	-	1000	-
Table-3, 4.1.6 and 8(ii) Broken fortified rice kernels,)	-	1000	-
Table-3, 4.1.6 and 8(iii) Foreign matter,)	-	1000	-
Table-3, 4.1.6 and 8(iv) Damaged grains)	-	1000	-
Table-3, 4.1.6 and 8(v) Discolored grains)	-	1000	-
Table-3, 4.1.6 and 8(vi) Chalky grains)	-	1000	-
Table-3, 4.1.6 and 8(vii) Admixture)	-	1000	-
Table-4, 4.7 and 8(i) Total plate count,)	-	3000	-
Table-4, 4.7 and 8(ii) Yeasts and moulds,)	-	3000	-
Table-4, 4.7 and 8(iii) Coliform count,)	-	3000	-
4.5(Cooking Quality)	-	1000	-

17 Jun, 2027

-
Exclusion: Cl.4.5.3 (Texture of the cooked fortified rice)

IS 8944 (2005)

Chlorpyrifos, emulsifiable concentrates - Specification (First Revision)

6500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2.1(Description)	-	500	NA
3.2.2(Cold Test)	-	1000	NA
3.2.3(Flash Point (Abel))	-	1000	NA
3.2.4(Emulsion Stability)	-	1000	NA
3.3.1(Chloropyrifos content)	-	2750	NA
3.3.2(Acidity (as H2SO4), )	-	500	NA
3.2.1(Description)	-	250	NA

17 Jun, 2027

-
-

IS 15573 (2018)

Polyaluminium chloride (First Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1, 5.1.2, 5.2, Table-1(i)(Aluminium as Al2O3,)	-	750	Rs.15000/- for liquid, Rs.14000/- for powder
5.1.1, 5.1.2, 5.2, Table-1(ii)(Basicity)	-	750	Rs.15000/- for liquid, Rs.14000/- for powder
5.1.1, 5.1.2, 5.2, Table-1(iii)(Chloride (as Cl))	-	750	Rs.15000/- for liquid, Rs.14000/- for powder
5.1.1, 5.1.2, 5.2, Table-1(iv)(Sulphates(as SO4))	-	750	Rs.15000/- for liquid, Rs.14000/- for powder
5.1.1, 5.1.2, 5.2, Table-1(v)(Specific gravity)	-	1500	Rs.15000/- for liquid, Rs.14000/- for powder
5.1.1, 5.1.2, 5.2, Table-1(x)(Insoluble)	-	750	Rs.15000/- for liquid, Rs.14000/- for powder
5.1.1, 5.1.2, 5.2, Table-1(xi)(Ph of 5% of solution)	-	750	Rs.15000/- for liquid, Rs.14000/- for powder
5.1.1, 5.1.2, 5.2, Table-1(ix)(Total organic carbon)	-	1500	Rs.15000/- for liquid, Rs.14000/- for powder
5.1.1, 5.1.2, 5.2, Table-1(vii)(Bulk density)	-	1500	Rs.15000/- for liquid, Rs.14000/- for powder
5.1.1,5.1.2,5.2, Table-1, Toxic substances(Mercury(as Hg))	-	750	Rs.15000/- for liquid, Rs.14000/- for powder
5.1.1, 5.1.2 ,5.2, Table-1, Toxic substances(Arsenic(as As))	-	750	Rs.15000/- for liquid, Rs.14000/- for powder
5.1.1, 5.1.2, 5.2, Table-1, Toxic substances(Cadmium(as Cd))	-	750	Rs.15000/- for liquid, Rs.14000/- for powder
5.1.1, 5.1.2, 5.2, Table-1, Toxic substances(Lead(as Pb))	-	750	Rs.15000/- for liquid, Rs.14000/- for powder
5.1.1.5.1.2,5.2, Table-1, Toxic substances(Iron(as Fe))	-	750	Rs.15000/- for liquid, Rs.14000/- for powder
5.1.1, 5.1.2, 5.2, Table-1, Toxic substances(Manganese(as Mn))	-	750	Rs.15000/- for liquid, Rs.14000/- for powder
5.1.1, 5.1.2, 5.2, Table-1, Toxic substances(Chromium (as Cr))	-	750	Rs.15000/- for liquid, Rs.14000/- for powder
5.1.1, 5.12, 5.2, Table-1, Toxic substances(Selenium (as Se))	-	750	Rs.15000/- for liquid, Rs.14000/- for powder
5.1.1(Description -)	-	750	Rs.15000/- for liquid, Rs.14000/- for powder

17 Jun, 2027

-
-

IS 5986 (2017)

Hot rolled steel sheet, plate and strip for forming and flanging purposes - Specification (Fourth Revision)

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 11(Expansion Test)	-	500	NA
Cl 15(Length, Width & Thickness)	-	750	NA
7.1(Carbon %)	-	500	NA
7.1(Manganese %)	-	500	NA
7.1(Phosphorus %)	-	500	NA
7.1(Sulphur %)	-	500	NA
7.1(Silicon %)	-	500	NA
7.1( Copper %)	-	500	-
7.1( Aluminium %)	-	500	NA
7.1( Nb)	-	500	NA
7.1(V)	-	500	NA
7.1( Ti)	-	500	NA
7.1(Cr)	-	500	NA
7.1(Mo)	-	500	NA
7.1(Ni)	-	500	NA
7.1( Nitrogen%)	-	2000	NA
Cl. 16(Weight)	-	250	NA
Cl. 15(Thickness)	-	250	NA
Cl. 15(Width)	-	250	NA
Cl. 8.3, Table 6 & 7( Elongation at 5.65√A Gauge length)	-	1000	NA
Cl. 8.3, Table 6 & 7(Elongation at 80 mm gauge length)	-	1000	NA
Cl. 8.3, Table 6 & 7(Elongation at 50 mm gauge length)	-	1000	NA
Cl. 8.3, Table 6 & 7(Yield strength)	-	1000	NA
Cl 15(Length, Width & Thickness)	-	750	NA
Clauses 8.2, 8.3 and 8.3.1 & table 6 & 7(Tensile Strength)	-	1000	NA
Clauses 8.2, 8.3 and 8.3.1 & table 6 & 7(Yield Strength)	-	1000	NA
Clauses 8.2, 8.3 and 8.3.1 & table 6 & 7(Elongation)	-	1000	NA

17 Jun, 2027

-
-

IS 1239 : Part 1 (2004)

Steel Tubes, Tubulars and Other Wrought Steel Fittings : Part 1 Steel Tubes (BI-LINGUAL)

13500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
12 AND AS PER IS 4736(UNIFORMITY OF ZINC COATING)	-	1000	NA
12 AND AS PER IS 4736(MASS OF ZINC COATING)	-	1000	NA
6.2 AND AS PER IS 513(NITROGEN)	-	2000	NA
6.2 AND AS PER IS 513(ALUMINIUM)	-	500	NA
6.2 AND AS PER IS 513(SILICON)	-	500	NA
6.2 AND AS PER IS 513(MANGANESE)	-	500	NA
6.2 AND AS PER IS 513(PHOSPHORUS)	-	500	NA
6.2 AND AS PER IS 513(SULPHUR)	-	500	NA
6.2 AND AS PER IS 513(CARBON)	-	500	NA
6.2 AND AS PER IS 10748(COPPER)	-	500	NA
6.1.1(MANGANESE)	-	500	NA
6.1.1(PHOSPHORUS)	-	500	NA
6.1.1(SULPHUR)	-	500	NA
6.1.1(CARBON)	-	500	NA
Cl. 6.1.1, table1 of IS 1239(Part1)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	NA
Cl. 6.1.1, table1 of IS 1239(Part1)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	NA
Cl. 6.1.1, table1 of IS 1239(Part1)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	NA
Cl. 6.1.1, table1 of IS 1239(Part1)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	NA
Cl. 15(Workmanship)	-	250	NA
Cl. 14.3(Flattening test (Over 50 mm NB))	-	500	NA
Cl. 14.1.1(Elongation)	-	1000	NA
Cl. 11(Length)	-	250	NA
Cl. 8, 9 Table 3,4 & 5(Thickness)	-	250	NA
Cl. 8 Table 3,4 & 5(Outside Diameter)	-	250	NA
Clause 14.1.1(Elongation Percent)	-	1000	NA
Clause 11.3(Approximate Length)	-	250	NA
Clause 11.2(Exact Length)	-	250	NA
Clause 11.1(Random Length)	-	250	NA
6.2(Carbon Equivalent as CE- IS:8811-98(RA12))	-	750	NA
Cl 8(Outer Diameter, Thickness & Mass)	-	1000	NA

17 Jun, 2027

-
-

IS 191 (2007)

Copper - Specification (Fourth Revision)

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1 - Table 4(Copper + Silver(By difference)-IS440)	-	500	NA
7.1 - Table 4(Silver- IS 440)	-	500	NA
7.1 - Table 4(Copper (any Silver present to be counted as copper)-IS440)	-	1700	NA
7.1 - Table 4(Phosphorus- IS 440)	-	500	NA
7.1 - Table 4(Arsenic- IS440)	-	500	NA
7.1 - Table 4(Antimony-IS440)	-	500	NA
7.1 - Table 4(Bismuth-IS 440)	-	500	NA
7.1 - Table 4(Iron IS 440)	-	500	NA
7.1 - Table 4(Lead IS 440)	-	500	NA
7.1 - Table 4(Nickel IS 440)	-	500	NA
7.1 - Table 4(Oxygen IS 440)	-	500	NA
7.1 - Table 4(Selenium - IS 440)	-	500	NA
7.1 - Table 4(Tellurium- IS 440)	-	500	NA
7.1 - Table 4(Tin - IS 440)	-	500	NA
7.1 - Table 4(Znic-IS 440)	-	500	NA
7.1 - Table 4(Selenium + Telluuium- IS 440)	-	1000	NA
7.1 - Table 4(Total Impurities- IS 440)	-	250	NA
7.1 - Table 4(Sulphur- IS 440)	-	500	NA
8.1(FREEDOM FROM DEFECTS)	-	250	NA
8.2(FREEDOM FROM DEFECTS)	-	250	NA
9.1- Table 5(Mass Resistivity- IS 3635)	-	2000	NA
8.1(FREEDOM FROM DEFECTS)	-	250	NA
8.2(FREEDOM FROM DEFECTS)	-	250	NA
7.1 - Table 4(Silver- IS 440)	-	200	NA

17 Jun, 2027

-
-

IS 302 : Part 1 (2024)

Household and Similar Electrical Appliances â Safety Part 1 General Requirements (Seventh Revision)

ALL

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
12(Charging of metal-ion batteries)	-	2500	NA
6(Classification- IS 302-1)	-	100	NA
5(General conditions for the tests)	-	100	NA
11.8(Temperature rise)	-	1500	NA
11.7(Duration corresponding)	-	100	NA
11.6(Combined appliances)	-	100	NA
11.5(Motor-operated appliances)	-	100	NA
11.4(Heating appliances)	-	100	NA
8.1.5(Live parts of built-in appliances)	-	200	NA
18(Endurance)	-	100	NA
17(Overload protection of transformers and associated circuits)	-	1000	NA
16(Leakage current and electric strength)	-	1100	NA
4(General requirement)	-	100	NA
32.1(Radiation Toxicity and Similar Hazards)	-	400	NA
31(Resistance to Rusting)	-	500	NA
30.2(Needle Flame Test)	-	500	NA
30.2(Glow Wire Test)	-	1500	NA
30.1(Ball pressure test)	-	1500	NA
29(clearance, creepage distances and solid insulation)	-	500	NA
28(Screw test and connections)	-	500	NA
27.1(Provision for Earthing, IS 302-1)	-	500	NA
26(Terminals for external conductors)	-	500	NA
25.8(Supply Connection and External Flexible Cords, IS 302-1)	-	500	NA
24(Components)	-	100	NA
23.1(Internal Wiring, IS 302-1)	-	400	NA
22.1(Construction, IS 302-1)	-	500	NANA
21.1(Mechanical Strength, IS 302-1)	-	100	NA
20.1(Stability & Mechanical Hazards, IS 302-1)	-	100	NA
19(Abnormal Operation)	-	2000	NA
18(Endurance)	-	100	NA
17(Over Load Protection of Transformers and associated circuits)	-	600	NA
16.3(Electric Strength (after clause 15 and 16.2))	-	500	NA
16.2(Leakage Current (after Clause 15))	-	500	NA
16.1(General)	-	100	NA
16.0(General)	-	100	NA
15.3(Humidity Test)	-	2000	NA
15.2(Spillage Test)	-	300	NA
15.1(Ingress Protection test other than IPX0 (IP test))	-	500	NA
15.0(Moisture resistance)	-	100	NA
14(Transient Over Voltages)	-	400	NA
13.3(Electric Strength at operating temperature)	-	500	NA
13.2(Leakage current at operating temperature)	-	500	NA
13(Leakage current and electric strength at operating temperature)	-	500	NA
11.3(Heating)	-	500	NA
11.2(General)	-	100	NA
11.1(General)	-	100	NANA
10.2(Current input)	-	100	NA
10.1(Power input)	-	100	NA
9(Starting of motor operation test requirements and tests)	-	100	NA
8.1.4(Protection against live parts against protective impedance)	-	100	NA
8.1.3(Protection against live parts in visible glowing heating elements)	-	100	NA
8.1.2(Protection against live parts in openings)	-	100	NA
8.1.1(Protection against live parts in all positions)	-	100	NA
7(Marking and instructions)	-	100	NA
A.2(Earth continuity test)	-	100	NA
Annex C(Ageing test on motors)	-	100	NA
Annex D(Thermal motor protectors)	-	100	NA
15.2(Moisture resistance)	-	100	NA
19.17(Abnormal Operation, IS 302-1)	-	100	NA
20.2(Stability & Mechanical Hazards, IS 302-1)	-	100	NA
21.2(Mechanical Strength, IS 302-1)	-	100	NA
21.3(Mechanical Strength, IS 302-1)	-	100	NA
22.5(Construction)	-	100	NA
22.6(Construction, IS 302-1)	-	100	NA
22.11(Construction, IS 302-1)	-	100	NA
22.16(Construction)	-	100	NA
22.32(Construction, IS 302-1)	-	100	NA
22.42(Construction)	-	100	NA
23.3(Internal Wiring, IS 302-1)	-	100	NA
25.6(Supply connection and external flexible cords, IS 302-1)	-	100	NA
25.7(Supply Connection and External Flexible Cords, IS 302-1)	-	100	NA
25.14(Supply Connection and External Flexible Cords, IS 302-1)	-	100	NA
25.15(Supply Connection and External Flexible Cords, IS 302-1)	-	100	NA
26.5(Terminals for external conductors)	-	100	NA
27.5(Provision for Earthing, IS 302-1)	-	100	NA
28.1(Screws and connections)	-	100	NA
22.2(Construction, IS 302-1)	-	100	NA
22.3(Construction, IS 302-1)	-	100	NA
B.22.4(Construction, IS 302-1)	-	100	NA
B.22.5(Construction, IS 302-1)	-	100	NA
12(Charging of metal-ion batteries)	-	0	NA
6(Classification- IS 302-1)	-	0	NA
5(General conditions for the tests)	-	0	NA
11.8(Temperature rise)	-	0	NA
11.7(Duration corresponding)	-	0	NA
11.6(Combined appliances)	-	0	NA
11.5(Motor-operated appliances)	-	0	NA
11.4(Heating appliances)	-	0	NA
8.1.5(Live parts of built-in appliances)	-	0	NA
18(Endurance)	-	0	NA
17(Overload protection of transformers and associated circuits)	-	0	NA
16(Leakage current and electric strength)	-	0	NA
4(General requirement)	-	0	NA
32.1(Radiation Toxicity and Similar Hazards)	-	0	NA
31(Resistance to Rusting)	-	0	NA
30.2(Needle Flame Test)	-	0	NA
30.2(Glow Wire Test)	-	0	NA
30.1(Ball pressure test)	-	0	NA
29(clearance, creepage distances and solid insulation)	-	0	NA
28(Screw test and connections)	-	0	NA
27.1(Provision for Earthing, IS 302-1)	-	0	NA
26(Terminals for external conductors)	-	0	NA
25.8(Supply Connection and External Flexible Cords, IS 302-1)	-	0	NA
24(Components)	-	0	NA
23.1(Internal Wiring, IS 302-1)	-	0	NA
22.1(Construction, IS 302-1)	-	0	NA
21.1(Mechanical Strength, IS 302-1)	-	0	NA
20.1(Stability & Mechanical Hazards, IS 302-1)	-	0	NA
19(Abnormal Operation)	-	0	NA
18(Endurance)	-	0	NA
17(Over Load Protection of Transformers and associated circuits)	-	0	NA
16.3(Electric Strength (after clause 15 and 16.2))	-	0	NA
16.2(Leakage Current (after Clause 15))	-	0	NANA
16.1(General)	-	0	NA
16.0(General)	-	0	NA
15.3(Humidity Test)	-	0	NA
15.2(Spillage Test)	-	0	NA
15.1(Ingress Protection test other than IPX0 (IP test))	-	0	NA
15.0(Moisture resistance)	-	0	NA
14(Transient Over Voltages)	-	0	NA
13.3(Electric Strength at operating temperature)	-	0	NA
13.2(Leakage current at operating temperature)	-	0	NA
13(Leakage current and electric strength at operating temperature)	-	0	NA
11.3(Heating)	-	0	NA
11.2(General)	-	0	NA
11.1(General)	-	0	NA
10.2(Current input)	-	0	NA
10.1(Power input)	-	0	NA
9(Starting of motor operation test requirements and tests)	-	0	NA
8.1.4(Protection against live parts against protective impedance)	-	0	NA
8.1.3(Protection against live parts in visible glowing heating elements)	-	0	NA
8.1.2(Protection against live parts in openings)	-	0	NA
8.1.1(Protection against live parts in all positions)	-	0	NA
7(Marking and instructions)	-	0	NA
A.2(Earth continuity test)	-	0	NA
Annex C(Ageing test on motors)	-	0	NA
Annex D(Thermal motor protectors)	-	0	NA
15.2(Moisture resistance)	-	0	NA
19.17(Abnormal Operation, IS 302-1)	-	0	NA
20.2(Stability & Mechanical Hazards, IS 302-1)	-	0	NA
21.2(Mechanical Strength, IS 302-1)	-	0	NA
21.3(Mechanical Strength, IS 302-1)	-	0	NA
22.5(Construction)	-	0	NA
22.6(Construction, IS 302-1)	-	0	NA
22.11(Construction, IS 302-1)	-	0	NA
22.16(Construction)	-	0	NA
22.32(Construction, IS 302-1)	-	0	NA
22.42(Construction)	-	0	NA
23.3(Internal Wiring, IS 302-1)	-	0	NA
25.6(Supply connection and external flexible cords, IS 302-1)	-	0	NA
25.7(Supply Connection and External Flexible Cords, IS 302-1)	-	0	NA
25.14(Supply Connection and External Flexible Cords, IS 302-1)	-	0	NA
25.15(Supply Connection and External Flexible Cords, IS 302-1)	-	0	NA
26.5(Terminals for external conductors)	-	0	NA
27.5(Provision for Earthing, IS 302-1)	-	0	NA
28.1(Screws and connections)	-	0	NA
22.2(Construction, IS 302-1)	-	0	NA
22.3(Construction, IS 302-1)	-	0	NA
B.22.4(Construction, IS 302-1)	-	0	NA
B.22.5(Construction, IS 302-1)	-	0	NA
12(Charging of metal-ion batteries)	-	-	-
6(Classification- IS 302-1)	-	-	-
5(General conditions for the tests)	-	-	-
11.8(Temperature rise)	-	-	-
11.7(Duration corresponding)	-	-	-
11.6(Combined appliances)	-	-	-
11.5(Motor-operated appliances)	-	-	-
11.4(Heating appliances)	-	-	-
8.1.5(Live parts of built-in appliances)	-	-	-
18(Endurance)	-	-	-
17(Overload protection of transformers and associated circuits)	-	-	-
16(Leakage current and electric strength)	-	-	-
4(General requirement)	-	-	-
32.1(Radiation Toxicity and Similar Hazards)	-	-	-
31(Resistance to Rusting)	-	-	-
30.2(Needle Flame Test)	-	-	-
30.2(Glow Wire Test)	-	-	-
30.1(Ball pressure test)	-	-	-
29(clearance, creepage distances and solid insulation)	-	-	-
28(Screw test and connections)	-	-	-
27.1(Provision for Earthing, IS 302-1)	-	-	-
26(Terminals for external conductors)	-	-	-
25.8(Supply Connection and External Flexible Cords, IS 302-1)	-	-	-
24(Components)	-	-	-
23.1(Internal Wiring, IS 302-1)	-	-	-
22.1(Construction, IS 302-1)	-	-	-
21.1(Mechanical Strength, IS 302-1)	-	-	-
20.1(Stability & Mechanical Hazards, IS 302-1)	-	-	-
19(Abnormal Operation)	-	-	-
18(Endurance)	-	-	-
17(Over Load Protection of Transformers and associated circuits)	-	-	-
16.3(Electric Strength (after clause 15 and 16.2))	-	-	-
16.2(Leakage Current (after Clause 15))	-	-	-
16.1(General)	-	-	-
16.0(General)	-	-	-
15.3(Humidity Test)	-	-	-
15.2(Spillage Test)	-	-	-
15.1(Ingress Protection test other than IPX0 (IP test))	-	-	-
15.0(Moisture resistance)	-	-	-
14(Transient Over Voltages)	-	-	-
13.3(Electric Strength at operating temperature)	-	-	-
13.2(Leakage current at operating temperature)	-	-	-
13(Leakage current and electric strength at operating temperature)	-	-	-
11.3(Heating)	-	-	-
11.2(General)	-	-	-
11.1(General)	-	-	-
10.2(Current input)	-	-	-
10.1(Power input)	-	-	-
9(Starting of motor operation test requirements and tests)	-	-	-
8.1.4(Protection against live parts against protective impedance)	-	-	-
8.1.3(Protection against live parts in visible glowing heating elements)	-	-	-
8.1.2(Protection against live parts in openings)	-	-	-
8.1.1(Protection against live parts in all positions)	-	-	-
7(Marking and instructions)	-	-	-
A.2(Earth continuity test)	-	-	-
Annex C(Ageing test on motors)	-	-	-
Annex D(Thermal motor protectors)	-	-	-
15.2(Moisture resistance)	-	-	-
19.17(Abnormal Operation, IS 302-1)	-	-	-
20.2(Stability & Mechanical Hazards, IS 302-1)	-	-	-
21.2(Mechanical Strength, IS 302-1)	-	-	-
21.3(Mechanical Strength, IS 302-1)	-	-	-
22.5(Construction)	-	-	-
22.6(Construction, IS 302-1)	-	-	-
22.11(Construction, IS 302-1)	-	-	-
22.16(Construction)	-	-	-
22.32(Construction, IS 302-1)	-	-	-
22.42(Construction)	-	-	-
23.3(Internal Wiring, IS 302-1)	-	-	-
25.6(Supply connection and external flexible cords, IS 302-1)	-	-	-
25.7(Supply Connection and External Flexible Cords, IS 302-1)	-	-	-
25.14(Supply Connection and External Flexible Cords, IS 302-1)	-	-	-
25.15(Supply Connection and External Flexible Cords, IS 302-1)	-	-	-
26.5(Terminals for external conductors)	-	-	-
27.5(Provision for Earthing, IS 302-1)	-	-	-
28.1(Screws and connections)	-	-	-
22.2(Construction, IS 302-1)	-	-	-
22.3(Construction, IS 302-1)	-	-	-
B.22.4(Construction, IS 302-1)	-	-	-
B.22.5(Construction, IS 302-1)	-	-	-

17 Jun, 2027

-
Included .w.e.f.27.02.2025 Exclusion CL 19.11.4.1 (Electrostatic discharges) CL 19.11.4.2 (Radiated fields) CL 19.11.4.3 (Fast transient bursts) CL 19.11.4.5 (Immunity to conducted discharges) CL 19.11.4.6 (Class 3 Voltage dips and interruptions) CL 19.11.4.7 (Harmonics) CL 32 (Radiation, toxicity and similar hazards) CL 24 (Components) "Domestic Electric Clothes Washing Machines (For testing charges please refer part 2 standard in LIMS)"

IS 13098 (2024)

AUTOMOTIVE VEHICLES TUBES FOR PNEUMATIC TYRES â SPECIFICATION (second revision)

15500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 3.1(Materials)	-	5500	NA
Cl 3.2(Classification)	-	250	NA
Cl 3.2.1(Blend Name)	-	0	NA
Cl 3.3(Fit)	-	1000	NA
Cl 3.3.1(Thickness Uniformity)	-	1000	NA
Cl 4.1.1(Elongation)	-	1000	NA
Cl 4.1.2(Strength of Splice)	-	1000	NA
Cl 4.1.3(Set After Ageing)	-	1000	NA
Cl 4.1.4(Accelerated Ageing)	-	3500	NA
Cl 5(AIR TIGHTNESS)	-	1500	NA
Cl 6(MARKING)	-	500	NA
Cl 3.1(Materials)	-	-	-
Cl 3.2(Classification)	-	-	-
Cl 3.2.1(Blend Name)	-	-	-
Cl 3.3(Fit)	-	-	-
Cl 3.3.1(Thickness Uniformity)	-	-	-
Cl 4.1.1(Elongation)	-	-	-
Cl 4.1.2(Strength of Splice)	-	-	-
Cl 4.1.3(Set After Ageing)	-	-	-
Cl 4.1.4(Accelerated Ageing)	-	-	-
Cl 5(AIR TIGHTNESS)	-	-	-
Cl 6(MARKING)	-	-	-

17 Jun, 2027

-
Included w.e.f. 21.01.2025

IS 5168 (2018)

Glass feeding bottles - Specification (First Revision)

22500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5.1(Materials)	-	6000	NA
Cl 5.2(Description)	-	500	NA
Cl 5.3(Capacity)	-	1000	NA
Cl 5.4(Types, Dimensions and Wall Thickness)	-	1000	NA
Cl 5.5(Scale and Graduations)	-	1500	NA
Cl 5.7(Thermal Shock Resistance)	-	2500	NA
Cl 5.5(Scale and Graduations)	-	1500	NA
5.6(Limit of Alkalinity)	-	2000	NA
5.8(Migration of Heavy and toxic Elements)	-	5500	NA
Cl 5.3(Capacity)	-	250	NA
"Clause 5.2.1 Sub Clause.5.2.1.1 &5.2.1.2 "(Manufacture, workmanship, Finish and Appearance)	-	250	NA
Cl 5.7(Thermal Shock Resistance)	-	2000	NA

17 Jun, 2027

-
-

IS 12701 (1996)

Rotational moulded polyethylene water storage tanks - specification (First Revision)

14500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2.3(Carbon Black Content )	-	1500	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
4.2.3(Carbon Dispersion Test)	-	2500	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
5(Types and Features )	-	500	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	1500	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	1500	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	1500	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	1500	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	1500	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	1500	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	1500	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	1500	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	1500	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	1500	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	1500	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	150	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	1500	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	1500	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	1500	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	1500	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
5.3(Types and Features )	-	500	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
5.6(Types and Features )	-	500	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
6.1(Finish)	-	500	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
7.1.1(Resistance to Deformation)	-	1500	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
7.1.2(Resistance to Deformation)	-	1500	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
7.2(Resistance to Impact)	-	1500	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
7.3(Test for Top Load Resistance)	-	1000	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
7.4(Tensile Strength)	-	1500	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
7.5(Flexural Modulus)	-	1500	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
7.6(overall Migration)	-	3000	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
5.1 Table 1 (7)(Minimum Weight of Tank (Without Lid))	-	500	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
5.2 Table 2 (7)(Minimum Wall Thickness)	-	250	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
5.4(Wall Thickness above effective height)	-	250	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
9.1(Lid Thickness)	-	250	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
9.1(Man-Hole and Hand-Hole Lids)	-	250	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
9.2(Man-Hole and Hand-Hole Lids)	-	250	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
9.2.1(Man-Hole and Hand-Hole Lids)	-	250	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
7.3(Test for Top Load Resistance)	-	1000	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
6.1(Finish)	-	250	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
4.2.1(Density)	-	1000	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
7.6(overall Migration)	-	3000	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)
4.2.2(MFR)	-	1000	Rs. :-14500/-( UPTO SIZE 1000 LITRE WATER TANK) Rs.:- 20500/-(ABOVE 1000 LITRE TANK)

17 Jun, 2027

-
-

IS 15609 (2005)

Polyethylene flexible pouches for the packing of natural mineral water and packaged drinking water - Specification

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.5 Annex J(Product resistance test for printed pouches)	-	500	NA
7.4 Annex H(Ink adhesion test for printed pouches)	-	500	NA
7.3 Annex G(Drop test )	-	500	NA
7.2 Annex F(Stack Load test)	-	500	NA
7.1 Annex E(Water Potability test (after 30 Days) a) Taste b) Odour)	-	1000	NA
6.1.10 Annex -6 of IS:2508:2016(Dart impact Resistance)	-	500	NA
6.1.9 Annex 4 of IS:2508:2016(Elongation at break - b. Crosswise direction)	-	500	NA
6.1.9 Annex 4 of IS:2508:2016(Elongation at break - a. Lengthwise direction)	-	500	NA
6.1.8 Annex 4 of IS:2508:2016(Tensile Strength b. Crosswise direction)	-	500	NA
6.1.8 Annex 4 of IS:2508:2016(Tensile Strength a. Lengthwise direction)	-	500	NA
6.1.7 IS: 9845:1998(Migration- b. Colour migration)	-	3500	NA
6.1.7 IS: 9845:1998(Migration- a. Amount of extractive )	-	2000	NA
6.1.6(Width)	-	250	NA
6.1.5 A-2 of IS: 2508:2016(Thickness)	-	250	NA
6.1.4(Odour)	-	250	NA
6.1.3(Winding of the Film )	-	250	NA
6.1.2(Film Form)	-	250	NA
6.1.1(Description)	-	250	NA
5(Material)	-	750	NA
Clause 7.2(Water Potability test (after 30 Days) a) Taste b) Odour)	-	1000	NA
6.1.7(Migration test)	-	3500	NA
7.2(Water potability)	-	1000	NA
7.3(Stack load test)	-	1000	NA
7.6(Product resistance test)	-	500	NA
7.5(Ink adhesion test)	-	500	NA
Table 3((i) Barium)	-	500	NA
Table 3(ii) Cobalt)	-	500	NA
Table 3(iii) Copper)	-	500	NA
Table 3(iv) Iron)	-	500	NA
Table 3(v) Lithium)	-	500	NA
Table 3(vi) Manganese)	-	500	NA
Table 3(viii) Antimony)	-	500	NA
Table 3(ix) Phthalic acid, bis(2-ethylhexyl)ester (DEHP))	-	500	NA
6.1.10(Dart Impact Resistance)	-	1000	NA
9(Packing and Marking)	-	250	NA

17 Jun, 2027

-
-

IS 15658 (2021)

Concrete Paving Blocks - Specification ( First Revision )

15500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Visual Rating of specimen after 50 cycles)	-	2500	NA
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Visual Rating of specimen after 25 cycles)	-	1250	NA
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Visual Rating of specimen after 10 cycles)	-	700	NA
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Cumulative Weight losses of specimen after 10, 25 & 50 cycles)	-	500	NA
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Weight losses of specimen after 50 cycles)	-	500	NA
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Weight losses of specimen after 25 cycles)	-	500	NA
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Weight losses of specimen after 10 cycles)	-	500	NA
Clause 7.3 & 9.1.4, Table 3, SI No. (v) b)(Average Flexural strength )	-	2000	NA
Clause 7.3 & 9.1.4, Table 3, SI No. (v) a)(Indivdual Flexural strength (i))	-	1000	NA
Clause 7.3 & 9.1.4, Table 3, SI No. (iv) b)(Average Tensile splitting strength )	-	1000	NA
Clause 7.3 & 9.1.4, Table 3, SI No. (iv) a)(Indivdual Tensile splitting strength (i))	-	2000	NA
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) b) ii)(Wet Abrasion resistance (Average of three test specimens))	-	500	NA
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) b) i)( Indivdual Wet Abrasion Resistance )	-	2000	NA
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) a) ii)(Dry Abrasion resistance (Average of three test specimens))	-	500	NA
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) a) i)( Indivdual Dry Abrasion Resistance )	-	2000	NA
Clause 7.3 & 9.1.4, Table 3, SI No. (ii) b)(Compressive strength (Average of eight test specimens))	-	500	NA
Clause 7.3 & 9.1.4, Table 3, SI No. (ii) a)(Indivdual Compressive strength (i))	-	2500	NA
Clause 7.3 & 9.1.4, Table 3, SI No. (i) b)(Water absorption (Average of three test specimens))	-	500	NA
Clause 7.3 & 9.1.4, Table 3, SI No. (i) a)( Indivdual Water absorption)	-	1500	NA
Clause 7.2 & 9.1.3, Table 2, SI No. (ix)(Deviation from squareness)	-	500	NA
Clause 7.2 & 9.1.3, Table 2, SI No. (viii)(Ratio of wearing face area and Plan area (Asw/Asp))	-	500	NA
Clause 7.2 & 9.1.3, Table 2, SI No. (vii)(Indivdual Plan Area (Asp))	-	500	NA
Clause 7.2 & 9.1.3, Table 2, SI No. (vii)(Plan Area (Asp))	-	500	NA
Clause 7.2 & 9.1.3, Table 2, SI No. (vi)(Indivdual Thickness of wearing Layer)	-	500	NA
Clause 7.2 & 9.1.3, Table 2, SI No. (vi)(Thickness of wearing Layer)	-	500	NA
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Indivdual Arris/chamfer, Depth)	-	500	NA
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Arris/chamfer, Depth)	-	500	NA
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Indivdual Arris/chamfer, Width)	-	500	NA
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Arris/chamfer, Width)	-	500	NA
Clause 7.2, Table No. 2, SI No. (iv) (Indivdual Aspect Ratio, L/Th)	-	250	NA
Clause 7.2, Table No. 2, SI No. (iv) (Aspect Ratio, L/Th)	-	250	-
Clause 7.2, Table No. 2, SI No. (iii) (Indivdual Thickness, Th)	-	250	NA
Clause 7.2, Table No. 2, SI No. (iii) (Thickness, Th)	-	250	NA
Clause 7.2, Table No. 2, SI No. (ii) (Indivdual Length, L)	-	250	NA
Clause 7.2, Table No. 2, SI No. (ii) (Length, L)	-	250	NA
Clause 7.2, Table No. 2, SI No. (i) (Indivdual Width, W)	-	250	-
Clause 7.2, Table No. 2, SI No. (i) (Width, W)	-	250	-
Clause 7.1.3 (Colour and Texture)	-	250	NA
Clauses 7.1.2 & 9.1.2 (Visual Inspection)	-	250	NA
10(Marking)	-	250	NA
7.2- TABLE-2- (i) IS-15658 (Annex-B)(Average Width -Higher)	-	250	NA
Clause 7.2 & 9.1.3, Table 2, SI No. (viii)(Indivdual Ratio of wearing face area and Plan area (Asw/Asp))	-	250	NA
Clause 7.1.1 (General Quality)	-	250	NA
7.2- TABLE-2- (i) IS-15658 (Annex-B)(Individual Width - Higher)	-	250	NA
7.2- TABLE-2- (i) IS-15658 (Annex-B)(Average Width -Lower)	-	250	NA
7.2- TABLE-2- (i) IS-15658 (Annex-B)(Individual Width - Lower)	-	250	NA

17 Jun, 2027

-
-

IS 13592 (2013)

Unplasticized Polyvinyl Chloride (PVC-U) Pipes for Soil and Waste Discharge System Inside and Outside Buiildings Including Ventilation and Rainwater System

18000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.5(Surface colour of the pipes shall be dark shade of grey)	-	500	NA
Cl6.3(The composition shall be based on PVC resin having a K-value of 64 or greater when tested in accordance with IS 4669)	-	2000	NA
Cl.7.1(Mean out side Diameter (For less than or equal to 40 mm- Average of 8 , For higher diameters up to 110 mm average of 6))	-	250	NA
Cl.7.1(Outside Diameter at any point (Take 8 reading reported minimum, maximum))	-	250	NA
Cl.7.1(Wall thickness "minimum,maximum" (Take 8 reading))	-	250	NA
Cl.7.2(Pipes shall be supplied in nominal lengths of 2, 3, 4 or 6 metres either plain or with socket for solvent cementing/grooved socket. Tolerances on specified length shall be + 10 mm and – 0 mm.The nominal length of the pipe with socket for solvent cementing/grooved socket shall be as given in Fig. 1.)	-	250	NA
Cl.7.3.1(Minimum wall thickness of socket on pipes shall be as given in Table 2 read with Fig. 2 and Fig. 3.)	-	250	NA
Cl.7.3.2(Dimensions of sockets for solvent cementing and grooved sockets of pipes shall be as given in Tables 3 and 4 respectively, read with Fig. 2 and 3.)	-	250	NA
Cl.8.1(The internal and external surface of the pipes shall be smooth and clean, and free from grooving and other defects. The end shall be clearly cut and shall be square with the axis of the pipe. The end may be chamfered on the plain side.)	-	250	NA
Cl.8.2(When tested by the method described in IS 12235 (Part 5), a length of pipe sample of 200 ± 20 mm shall not alter in length by more than 5 percent. In the case of socket ended pipes, this test shall be carried out on the plain portion of pipe taken at least 100 mm away from the root of the socket.)	-	500	NA
Cl8.3(This test shall be carried out for socket end pipes only. When tested by the method described in IS 12235 (Part 6), the test specimens shall not show blisters, excessive delamination or cracking or signs of weld line splitting.)	-	500	NA
Cl.8.4(When determined in accordance with IS 12235 (Part 2), the vicat softening temperature of the specimen shall not be less than 79°C.)	-	1000	NA
Cl.8.5(After the required period of exposure, the tensile strengths of two samples when tested as per IS 12235 (Part 13) shall not show difference of more than 20 percent of their initial tensile strengths)	-	3000	NA
Cl. 9, IS 12235 Part 7(Resistance to Sulphuric Acid)	-	2000	NA
Cl.10.1(When tested by method prescribed in IS 12235 (Part 9),the pipe shall have a true impact rate of not more than 10 percent. Mass of striker and height of fall shall be as per Annex A.)	-	1000	NA
Cl.10.2(When determined in accordance with the method described in IS 12235 (Part 13), the tensile strength at break shall not be less than 45 MPa.)	-	2000	NA
Cl.10.3(The axial shrinkage shall not exceed 2 percent when determined in accordance with Annex B.)	-	1000	NA
Cl.11.(Jointing of solvent cementing joints is to be carried out using solvent conforming to IS 14182. Apply a pressure of 0.05 MPa for a period of 15 min and there should be no leakage at any joint.)	-	1000	NA
Cl. 12, IS 12235 Part 11(Resistance to Di-Chloro-Methane)	-	1000	NA
8.6(Effect on Water Test)	-	4500	NA

17 Jun, 2027

-
-

IS 1786 (2008)

High strength deformed steel bars and wires for concretere inforcement - Specification (Fourth Revision)

35500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 9.4(Load In Other Direction From Bend)	-	1500	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
Cl 9.3(Load In One Direction)	-	1500	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
Cl 7.2(Weight)	-	500	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
Cl 5(Deformations and Surface Characteristics)	-	10000	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 CARBON +EQUIVELENT )	-	1000	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
4.1(Sulphur and phosphorous)	-	500	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
4.1(CE)	-	1000	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
4.1( Nitrogen%)	-	2000	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
4.1(Ni)	-	500	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
4.1(Mo)	-	500	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
4.1(Cr)	-	500	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
4.1( Ti)	-	500	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
4.1(V)	-	500	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
4.1( Nb)	-	500	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
4.1( Aluminium %)	-	500	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
4.1( Copper %)	-	500	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
4.1(Sulphur %)	-	500	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
4.1(Phosphorus %)	-	500	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
4.1(Manganese %)	-	500	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
4.1(Carbon %)	-	500	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
Cl.9.4 & Cl. 9.4.1(Rebend test)	-	1000	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
Cl. 9.3, Table 4(Bend Test )	-	1000	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
Cl. 8.1 Table 3(Elongation, percentage)	-	1000	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
Cl. 8.1 Table 3(TS/YS ratio)	-	500	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
Cl. 8.1 Table 3(Tensile Strength (TS))	-	1000	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
Cl. 8.1 Table 3(Yield Stress (YS))	-	1000	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
Cl. 7.2 Table -2 (Nominal Mass)	-	500	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 SULPHUR+PHOSPHUR)	-	0	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 MANGANESE)	-	500	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 NITROGEN)	-	2000	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 PHOSPHURS)	-	500	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 SULPHUR)	-	500	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 CARBON )	-	500	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
Cl.4.2 of IS 1786 (Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
Cl.4.2 of IS 1786 (Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
Cl.4.2 of IS 1786 (Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
Cl.4.2 of IS 1786 (Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
Cl.4.2 of IS 1786 (Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
Cl.4.2 of IS 1786 (Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	2000	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
Cl.4.2 of IS 1786 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
Cl.4.2 of IS 1786 (Grade:- Fe 415D,Fe 415S, Fe 500D,Fe 500S,Fe 550D)(Carbon Equivalent)	-	1000	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
Cl.4.2 of IS 1786 (Grade:- Fe 415,Fe 415D,Fe 415S,Fe 500,Fe 500D,Fe 500S,Fe 550,Fe 550D,Fe600,Fe 650,Fe 700)(Sulphur & Phosphorous)	-	500	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
8.18.1 Table 3(Total elongation at maximum force)	-	1000	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
Cl 5(Deformations and Surface Characteristics)	-	1000	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
5.7(PullOut (Bond Test))	-	10000	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
4.2(Niobium (Nb))	-	500	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
4.2(Boron (B))	-	500	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
Cl. 8.1 Table 3(TS/YS Ratio)	-	500	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
Cl. 5.3 (b)(The ribs contributing the projected area - Transverse Ribs)	-	1000	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
Cl. 5.3 (a)(The ribs contributing the projected area - Longitudinal Ribs)	-	1000	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
Cl. 8.1 Table 3(Total Elongation at Maximum Force)	-	1000	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
Cl. 6.2, 6.3 Table 1(Gross Cross Sectional Area, A)	-	500	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
Cl. 5.2(Surface Characteristics)	-	500	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
Clause 6.3(Effective Cross-sectional Area)	-	500	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM
5.7(Pull-out test - IS:2770(P1))	-	10000	Rs. 25000/-For SIZE UPTO 25 MM) Rs. 35000/-For SIZE ABOVE 25 MM

17 Jun, 2027

-
-

IS 10748 (2004)

Hot - Rolled steel strip for welded tubes and pipes - Specification (Second Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 12 & 13(Length, Width & Thickness)	-	1000	NA
7.1(Carbon %)	-	500	NA
7.1(Manganese %)	-	500	NA
7.1(Phosphorus %)	-	500	NA
7.1(Sulphur %)	-	500	NA
7.1(Silicon %)	-	500	NA
7.1( Copper %)	-	500	NA
7.1( Aluminium %)	-	500	NA
7.1( Nb)	-	500	NA
7.1(V)	-	500	NA
7.1( Ti)	-	500	NA
7.1(Cr)	-	500	NA
7.1(Mo)	-	500	NA
7.1(Ni)	-	500	NA
7.1( Nitrogen%)	-	2000	NA
Table 1 ( Clauses 7.1 ,7.2 )(TITANIUM)	-	500	NA
Table 1 ( Clauses 7.1 ,7.2 )(VANADIUM)	-	500	NA
Table 1 ( Clauses 7.1 ,7.2 )(NIOBIUM)	-	500	NA
Table 1 ( Clauses 7.1 ,7.2 )(CARBON EQUIVELENT )	-	500	NA
Table 1 ( Clauses 7.1 ,7.2 )(Molybdenum)	-	500	NA
Table 1 ( Clauses 7.1 ,7.2 )(Chromium)	-	500	NA
Table 1 ( Clauses 7.1 ,7.2 )(NITROGEN)	-	2000	NA
Table 1 ( Clauses 7.1 ,7.2 )(MANGANESE)	-	500	NA
Table 1 ( Clauses 7.1 ,7.2 )(PHOSPHURS)	-	500	NA
Table 1 ( Clauses 7.1 ,7.2 )(SULPHUR)	-	500	NA
Cl. 12, 13(Camber)	-	500	NA
Cl. 12, 13(Thickness)	-	500	NA
Cl. 8, Table 3(Elongation)	-	1000	NA
Cl. 8, Table 3(Yield Stress)	-	1000	NA
Cl 12 & 13(Length, Width & Thickness)	-	1000	NA
Cl 11(Workmanship)	-	250	NA
8.0 (1)(Tensile Strength-IS:1608(P1))	-	1000	NA
8.0 (2)(Yield Strength-IS:1608(P1))	-	1000	NA
8.0 (3)(Elongation on 5.65 SoA GL-IS:1608(P1))	-	1000	NA
Table 1 ( Clauses 7.1 ,7.2 )(Tungsten (W))	-	500	NA
Table 1 ( Clauses 7.1 ,7.2 )(Boron (B))	-	500	NA

17 Jun, 2027

-
-

IS 446 (2017)

Rubber hoses, textile - Reinforced, for compressed air - Specification (Fifth Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.2, Table 3(Low temperature Flexibility)	-	1000	NA
7.2, Table 3(Flexibility at 23°C)	-	1000	NA
7.2, Table 3(Ozone Resistance)	-	2500	NA
7.2, Table 3(Adhesion between Components- Cover and Reinforcement)	-	1500	NA
7.2, Table 3(Adhesion between Components- Reinforcement layers)	-	1500	NA
7.2, Table 3(Adhesion between Components- Lining and Reinforcement)	-	1500	NA
7.2, Table 3(Minimum Bursting Pressure for type 3)	-	1000	NA
7.2, Table 3(Minimum Bursting Pressure for type 2)	-	1000	NA
7.2, Table 3(Minimum Bursting Pressure for type 1)	-	1000	NA
7.2, Table 3(Change in Diameeter at Maximum working Pressure)	-	1000	NA
7.2, Table 3(Change in Length at Maximum working Pressure)	-	1000	NA
7.2, Table 3(Proof Pressure at 23°C for type 3)	-	1000	NA
7.2, Table 3(Proof Pressure at 23°C for type 2)	-	1000	NA
7.2, Table 3(Proof Pressure at 23°C for type 1)	-	1000	NA
7.1, Table 2(Resistance to Liquid , Increase in Volume (Class C only)-Cover)	-	2000	NA
7.1, Table 2(Resistance to Liquid , Increase in Volume (Class B only)-Lining)	-	2000	NA
7.1, Table 2(Accelerated Ageing for all types: Change in Elongation of Cover of its original value)	-	3000	NA
7.1, Table 2(Accelerated Ageing for all types: Change in Tensile Strength of Cover of its original value)	-	3000	NA
7.1, Table 2(Elongation at Break of Cover of all types)	-	3000	NA
7.1, Table 2(Elongation at Break of Lining of all types)	-	1000	NA
7.1, Table 2(Tensile Strength of Cover)	-	1000	NA
7.1, Table 2(Tensile Strength of Lining)	-	1000	NANA
6, Dimensions(Thickness of Cover of Type 3)	-	500	NA
6, Dimensions(Thickness of Cover of Type 2)	-	500	-
6, Dimensions(Thickness of Cover of Type 1)	-	500	-
6, Dimensions(Tolerance on Length)	-	500	NA
6, Dimensions(Concentricity)	-	500	NA
5(Material and Construction)	-	500	NA
Cl 7.2 & Table 3(Low-temperature flexibility)	-	500	NA
Cl 7.2 & Table 3(Flexibility at 23 °C)	-	500	NA
Cl 7.2 & Table 3(Ozone resistance)	-	2000	For BIS samples: 1.5 times of BIS testing charges
Cl 7.2 & Table 3(Adhesion between components)	-	2000	NA
Cl 7.2 & Table 3(Minimum burst pressure)	-	1000	NA
Cl 7.2 & Table 3(Change in diameter at maximum working pressure)	-	1000	NA
Cl 7.2 & Table 3(Change in length at maximum working pressure)	-	1000	NA
Cl 7.2 & Table 3(Proof pressure)	-	1000	NA
Cl 7.1 & Table 2(Resistance to liquids-Increase in volume (max.) (class C only) )	-	2000	NA
Cl 7.1 & Table 2(Resistance to liquids-Increase in volume (max.) (class B only) )	-	2000	NA
Cl 7.1 & Table 2(Resistance to liquids-Increase in volume (class A))	-	2000	NA
Cl 7.1 & Table 2(Resistance to ageing-Change in elongation at break from original value (max.) original value (max.) )	-	1000	NA
Cl 7.1 & Table 2(Resistance to ageing-Change in tensile strength from original value (max.) )	-	1000	NA
Cl 7.1 & Table 2(Minimum elongation at break)	-	500	NA
Cl 7.1 & Table 2(Minimum tensile strength)	-	500	NA
Cl 6.4(Minimum thickness of lining and cover-Type 3)	-	500	NA
Cl 6.4(Minimum thickness of lining and cover-Type 2 )	-	500	NA
Cl 6.4(Minimum thickness of lining and cover-Type 1 )	-	500	NA
Cl 6.3(Tolerance on length)	-	500	NA
Cl 6.2(Concentricity)	-	500	NA
Cl 6.1 & Table 1(Internal diameters and tolerances)	-	500	NA
Cl 5(Materials and construction)	-	500	NA

17 Jun, 2027

-
-

IS 14756 (2024)

Stainless Steel Utensils - Specification (THIRD REVISION)

32500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 3.1(Material used for manufacturing utensils)	-	8500	NA
Cl 3.2(Material used for composite bottom)	-	8500	NA
Cl 3.3(Material used for body of utensil of 3-ply construction)	-	8500	NA
Cl 3.4(Material used for stainless steel lid)	-	8500	NA
Cl 3.5(Material used for tempered glass lid)	-	8500	NA
Cl 3.5(Material used for stainless steel rim)	-	8500	NA
Cl 4.2 & Table 1(Minimum Sheet Thickness for Body of Utensil)	-	500	NA
Cl 4.2 & Table 2(Minimum Sheet Thickness for Lid of Utensil)	-	500	NA
Cl 4.2(Thickness of the finished utensil)	-	500	NA
Cl 4.4 (i)(Thickness of Aluminium disc/core)	-	500	NA
Cl 4.4 (ii)(Thickness of Protector/cowl)	-	500	NA
Cl 4.5(Minimum sheet thickness (3-ply utensil))	-	500	NA
Cl 4.5(Thickness of finished utensil (3-ply utensil))	-	500	NA
Cl 5.1(Manufacturing defect & visual appearance)	-	500	NA
Cl 6.1(Staining Test (Type Test - Frequency Once in a Year))	-	1500	NA
Cl 6.2(Mechanical Shock Test (for Cladded Utensils Only))	-	1500	NA
Cl 6.3(Thermal Shock Test (for Cladded Utensils Only))	-	1500	NA
Cl 6.4(Dry Heat Test (for Cladded Utensils Only))	-	1500	NA
Cl 6.5(Coating Thickness Test (for Copper Deposit))	-	2500	NA
Cl 6.6(Thermal shock test (3-ply construction utensil body))	-	1500	NA
Cl 6.7(Nominal Capacity Test)	-	250	NA
Cl 8(Marking)	-	250	NA
Cl 4.3(Classification)	-	250	NA
CL 5.2(Accessibility for cleaning)	-	250	NA
Cl 5.3(Joining of handles to the utensils)	-	500	NA
Cl 5.4(Requirement for handles)	-	15000	NA
Cl 5.5(Welding (Finish))	-	250	NA
Cl 5.6(Finish of 3-ply utensil)	-	250	NA
Cl 5.7(Requirement for coating)	-	1500	NA
Cl 5.8(Coating thickness test)	-	1500	NA
Cl 5.8(Coating adhesion test)	-	1500	NA
Cl 5.8.1(Thermal shock test (Coating))	-	1500	NA

17 Jun, 2027

-
Included.w.e.f.14.01.2025

IS 2887 (2017)

Laundry soap powders/flakes - Specification (Third Revision)

15500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5 (5.1.1)(Description)	-	500	NA
5 (5.1.2)(Odour and lathering Properties)	-	500	NA
5.2,7.31 and 8.1Table 1(Total fatty matter)	-	2000	NA
5.2,7.31 and 8.1Table 1(Rosin acid)	-	2000	NA
5.2,7.31 and 8.1Table 1(Unsaponifiable matter)	-	2000	NA
5.2,7.31 and 8.1Table 1(Free caustic alkali)	-	1000	NA
5.2,7.31 and 8.1Table 1(Matter insoluble in alcohol)	-	2000	NA
5.2,7.31 and 8.1Table 1(Glycerol)	-	1500	NA
5.2,7.31 and 8.1Table 1(Hexbromide test ( on fatty acid))	-	500	NA
5.2,7.31 and 8.1Table 1(Active alkalinity)	-	500	NA
5.2,7.31 and 8.1Table 1(Chloride (as sodium chloride))	-	500	NA
5.2,7.31 and 8.1Table 1(LSD?NSD)	-	1500	NA

17 Jun, 2027

-
-

IS 18755 (2024)

Tri-ply SS-AL-SS material used for manufacture of utensils and kitchen appliances Specification

ALL

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-7.1.1(Tensile properties)	-	1500	NA
Cl-7.1.1(Apparent Yield Strength)	-	1500	NA
Cl-7.1.1(Tensile Strength Mpa,)	-	1500	NA
Cl-7.2.1(Bond strength of Tri-Ply)	-	1500	NA
Cl-8.3, table-3(T-Peel Strength, N/mm, Min SS304 and Al 19500 interface)	-	1500	NA
Cl-8.3, table-3(T-Peel Strength, N/mm, Min SS430 and Al 19500 interface)	-	1500	NA
Cl-9.1(Thickness)	-	500	NA
Cl-8.2(specimen for peel strength)	-	1500	NANA
Cl-9.2(Diameter)	-	500	NA
Cl-9.3(Flatness)	-	500	NA
Cl-10(surface finish)	-	500	NA
Cl-11(Workmanship, finish and appearance)	-	500	NA
Cl-14(Marking)	-	250	NA

17 Jun, 2027

-
Included.w.e.f.14.01.2025

IS 5522 (2014)

Stainless steel sheets and strips for utensils - Specification (Third Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 7.1 & 7.2 Table 1(Carbon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	NA
Cl. 7.1 & 7.2 Table 1(Silicon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	NA
Cl. 7.1 & 7.2 Table 1(Manganese -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	NA
Cl. 7.1 & 7.2 Table 1(Nickel -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	NA
Cl. 7.1 & 7.2 Table 1(Chromium -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	NA
Cl. 7.1 & 7.2 Table 1(Sulphur -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	NA
Cl. 7.1 & 7.2 Table 1(Phosphorus -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	NA
Cl. 7.1 & 7.2 Table 1(Nitrogen -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	2000	NA
8.2, Table 3(Tensile Test-1608:Part 1)	-	1000	NA
8.2, Table 3(Proof Stress, N/mm2)	-	1000	NA
8.2, Table 3(Tensile Strength, N/mm2)	-	1000	NA
8.2, Table 3(Elongation, %)	-	800	NA
8.3(Hardness , max-IS 1500 or IS 1501 (Part 1) or IS 1586)	-	500	NA
8.4(Bend Test)	-	1000	NA
8.5(Erichsen Cupping Test)	-	1000	NA
10.1(Thickness, mm)	-	250	NA
10.2(width, mm)	-	250	NA
10.3(Length, mm)	-	250	NA
10.4(Flatness,mm)	-	250	NA
10.5(Camber, mm)	-	250	NA
11(Surface Finish)	-	250	NA
Cl . 6 .0(Freedom from defect)	-	100	NA

17 Jun, 2027

-
-

IS 15905 (2011)

Hubless centrifugally cast (Spun) iron pipes, fittings and accessories - Spigot series - Specification

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(shall conform to FG 150 grade,appropriate, specified in IS 210.)	-	2500	-
5.3(Hardness )	-	1000	-
7.1(Visual Inspection and Hammer Test)	-	250	-
8.1(Crushing Strength )	-	1500	-
9.1(Hydraustatic Test)	-	2500	-
10.1(External Diameter)	-	250	-
10.2, Table 3, Sl no. I to IV(Pipe Thickness)	-	250	-
10.2 , Table 3, Sl no. I to IV(Fittings Thickness)	-	250	-
10.3(Length)	-	250	-
10.5(Masses)	-	250	-
12.1 to 12.5(Coating )	-	500	-
5.3(Hardness )	-	1000	-
7.1(Visual Inspection and Hammer Test)	-	500	-
8.1(Crushing Strength )	-	250	-
9.1(Hydraustatic Test)	-	2500	-
10.1(External Diameter)	-	250	-
10.2, Table 3, Sl no. I to IV(Pipe Thickness)	-	250	-
10.2 , Table 3, Sl no. I to IV(Fittings Thickness)	-	250	-
10.3(Length)	-	250	-
10.5(Masses)	-	250	-
11.2.5, Table 8, Sl no. I to II(a)	-	250	-
11.2.5, Table 8, Sl no. I to II(Nominal Size (DN 1))	-	100	-
11.2.5, Table 8, Sl no. I to II(b)	-	100	-
11.2.5, Table 8, Sl no. I to II(c )	-	100	-
11.2.5, Table 8, Sl no. I to II(d)	-	100	-
11.2.6, Table 9, Sl no. I to II(Nominal Size (DN ))	-	100	-
11.2.6, Table 9, Sl no. I to II(a)	-	100	-
11.2.6, Table 9, Sl no. I to II(b)	-	100	-
11.2.6, Table 9, Sl no. I to II(c)	-	100	-
11.2.6, Table 9, Sl no. I to II(r)	-	100	-
11.2.7, 11.2.8, 11.2.9, 11.2.10 Table 10,11,12 & 13 (Nominal Size (DN 1))	-	100	-
11.2.7, 11.2.8, 11.2.9, 11.2.10 Table 10,11,12 & 13 (Nominal Size (DN 2))	-	100	-
11.2.7, 11.2.8, 11.2.9, 11.2.10 Table 10,11,12 & 13 (L)	-	100	-
11.2.7, 11.2.8, 11.2.9, 11.2.10 Table 10,11,12 & 13 (a)	-	100	-
11.2.7, 11.2.8, 11.2.9, 11.2.10 Table 10,11,12 & 13 (b)	-	100	-
11.2.11, Table 14, (Nominal Size (DN 1))	-	100	-
11.2.11, Table 14, (Nominal Size (DN 2))	-	100	-
11.2.11, Table 14, ( L)	-	100	-
11.2.12, Table 15(Nominal Size (DN ))	-	100	-
11.2.12, Table 15(L)	-	100	-
11.2.12, Table 15(a)	-	100	-
11.2.12, Table 15(b)	-	100	-
11.2.13, Table 16(Nominal Size (DN 1))	-	100	-
11.2.13, Table 16(Nominal Size (DN 2))	-	100	-
11.2.13, Table 16(L)	-	100	-
11.2.13, Table 16(a)	-	100	-
11.2.13, Table 16(b)	-	100	-
11.2.13, Table 16(c)	-	100	-
11.2.13, Table 16(d)	-	100	-
11.2.13, Table 16(r)	-	100	-
11.2.14, Table 17,(Nominal Size (DN ))	-	100	-
11.2.14, Table 17,(a)	-	100	-
11.2.14, Table 17,(b)	-	100	-
11.2.14, Table 17,(b)	-	100	-
11.2.14, Table 17,(r)	-	100	-
11.2.14, Table 17,(j)	-	100	-
11.2.14, Table 17,(k)	-	100	-
11.2.14, Table 17,(d)	-	100	-
11.2.15, Table 18,(Nominal Size (DN 1))	-	100	-
11.2.15, Table 18,(Nominal Size (DN 2))	-	100	-
11.2.15, Table 18,(L)	-	100	-
11.2.15, Table 18,(a)	-	100	-
11.2.15, Table 18,(b)	-	100	-
11.2.15, Table 18,(c)	-	100	-
11.2.15, Table 18,(d)	-	100	-
11.2.15, Table 18,(e )	-	100	-
11.2.15, Table 18,(f )	-	100	-
11.2.15, Table 18,(g)	-	100	-
11.2.16, Table 19, (Nominal Size (DN 1))	-	100	-
11.2.16, Table 19, (Nominal Size (DN 2))	-	100	-
11.2.16, Table 19, (L)	-	100	-
11.2.16, Table 19, (a)	-	100	-
11.2.16, Table 19, (b)	-	100	-
11.2.16, Table 19, (c)	-	100	-
11.2.16, Table 19, (d)	-	100	-
11.2.17, Table 20, (Nominal Size (DN 1))	-	100	-
11.2.17, Table 20, (Nominal Size (DN 2))	-	100	-
11.2.17, Table 20, (L)	-	100	-
11.2.17, Table 20, (a)	-	100	-
11.2.17, Table 20, (b)	-	100	-
11.2.17, Table 20, (c)	-	100	-
11.2.17, Table 20, (d)	-	100	-
11.2.18, Table 21, (Nominal Size (DN ))	-	100	-
11.2.18, Table 21, (L)	-	100	-
11.2.18, Table 21, (a)	-	100	-
11.2.18, Table 21, (b)	-	100	-
11.2.19, Table 22, (Nominal Size (DN ))	-	100	-
11.2.19, Table 22, (L)	-	100	-
11.2.19, Table 22, (c)	-	100	-
11.2.19, Table 22, (d)	-	100	-
Cl. A-1, Table 23, (Nominal Size (DN ))	-	100	-
Cl. A-1, Table 23, (Outside Dia (D))	-	100	-
Cl. A-1, Table 23, (Thickness (I))	-	100	-
Cl. A-1, Table 23, (Height (H))	-	100	-
Cl. A-2, Table 24, (Nominal Size (DN ))	-	100	-

17 Jun, 2027

-
-

IS 12818 (2010)

Unplasticized polyvinyl chloride (Pvc - U) screen and casing pipes for bore/tubewells - Specification (Second Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.6(Vicat Softening Temperature IS 12235 (Part 2).)	-	1000	-
9.5(Tensile Strength IS 12235(Part 13))	-	1500	-
9.4 and Table 14(Resistance to External Blows at 0 ?C IS 12235 (Part 9))	-	1000	-
9.3(Density IS 12235 (Part 14))	-	1000	-
9.2(Internal Diameter)	-	500	-
9.1( Visual Appearance)	-	250	-
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	250	-
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	250	-
8.4(Sealing rings - Hardness)	-	500	-
8.1 to 8.3 and Table 11 &12 Fig 3A & 4A(THREADING OF SCREEN ANDCASING PIPES. IS 554.)	-	500	-
7.5 and Table 10 Fig 2A & 2B(Approximate Free Passage Area, in Percent (Mean Value) for Width of Slot (w))	-	250	-
7.5 and Table 10 Fig 2A & 2B(Minimum number of slots on the circumference of the cross-section.)	-	250	-
7.5 and Table 10 Fig 2A & 2B(Summation of slot lengths over internal circumference of the cross- section.)	-	250	-
7.4 Table 8 & 9 Fig 1(Segmental length for Spigot (average of 4.0))	-	250	-
7.4 Table 8 & 9 Fig 1(Segmental length,mm for socket (average of 4.0))	-	250	-
7.4 Table 8 & 9 Fig 1(Segmental length, l3)	-	250	-
7.4 Table 8 & 9 Fig 1(Effective length, l2)	-	250	-
7.3.2(Rib height)	-	250	-
7.3.1(No.of Ribs)	-	250	-
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Max)	-	250	-
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Min)	-	250	-
7.1, 7.2 and Table 5, 6 & 7 Fig 1B(Mean outside dia over connection,mm (Take 4 reading and maximum valu reported))	-	250	-
7.1, 7.2 and Table 5, 6 & 7 Fig 1B(Outer Diameter at any point, Max)	-	250	-
7.1, 7.2 and Table 5, 6 & 7 Fig 1B(Outer Diameter at any point , Min)	-	250	-
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter of Pipe , Max)	-	250	-
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter of Pipe, Min)	-	250	-
7.2 and Table 5, 6 & 7 Fig 1B(Nominal Diameter)	-	250	-
7.2 and Table 5, 6 & 7 Fig 1B(DIMENSIONS - Casing Pipes)	-	250	-
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Wall thickness)	-	250	-
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Mean Outer Diameter over Connection)	-	250	-
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Outer Diameter at any point )	-	250	-
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Mean Outer Diameter of Pipe)	-	250	-
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Nominal Diameter)	-	250	-
4.1.2 (Ref. Cl 11 of IS 4669)(Composition -Sulphated ash content )	-	1000	-
4.1.2 (Ref. Cl 5.1. of IS 4669)(Composition - Loss on heating )	-	500	-
4.1.1 (Ref. 3.4.1. of IS 10151)(Composition - The monomer content (VCM content) in the resin - Annex A ofIS 10151)	-	500	-
5(COLOUR)	-	250	-
8.4(Sealing elements a. Elastomeric material b. Shore A hardness of sealing Elements )	-	1000	-
8.4(Width b)	-	250	-
8.3.1 & 8.3.2 (Threading of casing pipe (from 100 to 200 DN Table – 11 & Fig. 3A) & (from 250 to 400 DN Table – 12 & Fig. 4A) Outside diameter d1(+0, -0.3) d2 d3 D1 (+0.3, -0) D2 D4 D5 (+0.3, -0) Z h3 (+0, -0.1) H4 (+0, -0.1) )	-	250	-
8.2(Threading of casing pipe As per IS 554 (from 40 to 80mm DN) Number of threads in 25.4mm Pitch (P) Height of thread (h) Major (Gauge Diameter) d Pitch(d2) Minor (d1) External Thread gauge length Nominal No. of turns of thread max min )	-	250	-
7.5.1 7.5.2 (Slot Dimension (Table 10) Fig 2A & 2B a. Minimum number of slot on the circumference b. Σa±5% c. Mean value of approximate free passage area (%) for width of slot (w) d. Tolerance on width of slot (w) e. Width of material between slot (b))	-	250	-
5.0(Colour of Pipes)	-	250	-
9.7(Effect on Water a) Lead (first extraction) b) Lead (Third extraction) c) Dialkyl Tin C4 & higher homologues measured as Tin (Third extraction) d) Cadmium (All three extracts) e) Mercury (All three extracts) f) Other Toxic Substances )	-	5500	--
4.1.2(K-Value as per IS-4669)	-	1500	-
4.1.1 (VCM Content as per IS 10151 (Annex A))	-	1000	-
7.1(Screen Pipes)	-	250	-
7.2(Link Twisted (Cross chain))	-	500	-

17 Jun, 2027

-
-

IS 444 (2017)

Rubber hoses, textile - Reinforced, for general - Purpose water applications - Specification (Fifth Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Lining - IS 444)	-	100	NA
5(Reinforcement - IS 444)	-	100	NA
5(Cover - IS 444)	-	100	NA
5(Lining and Cover - IS 444)	-	100	NA
6.1- Table 1(Internal diameters - ISO 4671)	-	250	NA
6.2(Concentricity - ISO 4671)	-	250	NA
6.3(Length -IS 4671)	-	250	NA
6.4( thickness of the lining plus cover - ISO 4671)	-	250	NA
6.4(If the cover is fluted, the depth of the flutes - ISO 4671)	-	250	NA
7.1 - Table 2( tensile strength of Lining - ISO 37 )	-	1000	NA
7.1 - Table 2( tensile strength of Cover - ISO 37 )	-	1000	NA
7.1 - Table 2(elongation at break of Lining - ISO 37)	-	500	NA
7.1 - Table 2(elongation at break of Cover - ISO 37)	-	500	NA
7.1 - Table 2(Change in tensile strength of Lining from original value after ageing(max) - ISO 188 and ISO 37)	-	1000	NA
7.1 - Table 2(Change in tensile strength of Cover from original value after ageing(max) - ISO 188 and ISO 37)	-	1000	NA
7.1 - Table 2(Change in elongation at break of Lining from original value after ageing (max.) - ISO 188 and ISO 37)	-	500	NA
7.1 - Table 2(Change in elongation at break of Cover from original value after ageing (max.) - ISO 188 and ISO 37)	-	500	NA
7.2 - Table 3(Proof pressure at 23 °C - ISO 1402)	-	2500	NA
7.2 - Table 3(Change in length at proof pressure - ISO 1402)	-	1250	NA
7.2 - Table 3(Minimum burst pressure - ISO 1402)	-	1250	NA
7.2 - Table 3(Adhesion between components - ISO 8033)	-	1000	NA
7.2 - Table 3(Ozone resistance - ISO 7326)	-	2500	NA
7.2 - Table 3(Flexibility at 23 °C - Method A of ISO 1746)	-	500	NA
7.2 - Table 3(Low-temperature flexibility - Method B of ISO 4672)	-	500	NA

17 Jun, 2027

-
-

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

35400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.2(Colour)	-	250	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
6.2.1(6.1.1 Identification Stripes)	-	250	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
7.2(Length)	-	250	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
Cl-7.4(Mean Outside Diameter (For upto 50 mm take 8 reading, above 50mm take 6 reading & average will be reported))	-	500	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
8,/8.1/8.1.1 table-5(PERFORMANCE REQUIREMENTS / Hydraulic Characteristics/ Internal Pressure Creep Rupture Test of Pipe)	-	15000	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
8.2(Longitudinal Reversion Test)	-	1500	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
8.3(Carbon black)	-	2500	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
8.4( Melt Flow Rate)	-	1500	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
8.5 (Oxidation Induction Time)	-	4000	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
8.6(Overall migration)	-	3500	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
8.7(Density)	-	1000	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
8.8(Tensile Strength for Butt-fusion)	-	1500	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
8.9 table-6(Elongation at Break)	-	1000	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
8.10(Slow Crack Growth Rate)	-	3500	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
5.2(Polyethylene Resin)	-	8000	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
5.3(c)(Carbon Black Master Batch)	-	1500	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
5.3(d)(Carbon Black Master Batch)	-	1500	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
5.4(Anti oxydent)	-	1000	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
5.3(b)(Carbon Black Master Batch)	-	2000	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
5.3(e)(Carbon Black Master Batch)	-	1000	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
8.1.2 table -5(Internal Pressure Creep Rupture Test of Pipe Joints)	-	1000	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
7.4.1.2(Ovality)	-	250	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
Cl-7.4(Mean Outside Diameter (For upto 50 mm take 8 reading, above 50mm take 6 reading & average will be reported))	-	250	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
5.3(b)(Carbon Black Master Batch)	-	1500	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
5.3 (a)(Carbon Black Master Batch)	-	1500	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
5.2(Density)	-	1000	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
5.2(Volatile matter Content)	-	1000	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
5.3(Toluene Extract)	-	1500	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
Clause 7.1(Visual Apperance)	-	250	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
Clause 8.3(Carbon Black content)	-	1500	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
Clause 8.3(Carbon Black Dispersion)	-	1500	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
Clause 8.6(Overall migration (stimulate))	-	1000	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
Clause 8.6(Overall migration (surface of material))	-	1000	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
7.1(Visual Appearance)	-	250	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
Table-2 (iii, iv)(Thermal Stability (Oxidation Induction Time), Volatile Matter)	-	1000	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
Cl. 8.3(Carbon Black Content)	-	1500	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
Cl. 8.3(Carbon Black Dispersion)	-	1500	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
5.2,T2(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	2500	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
8.7(Density-IS 7328:2020)	-	1000	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
8.7(Corrected Density- IS 7328:2020)	-	1000	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
8.9,T6("Tensile - IS 4984-2016 (Annexure-H)")	-	1000	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
8.9,T6("Elongation -IS 4984-2016 (Annexure-H)")	-	1000	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
Cl 8.3(Carbon Black Content)	-	1500	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/
Cl 8.3(Carbon Black Dispersion)	-	1500	For DN 10mm - 400mm= Rs. 36500/- For DN 401mm - 630mm= Rs. 42500/-

17 Jun, 2027

-
-

IS 15965 (2012)

Pre - Painted aluminium zinc alloy metallic coated steel strip and sheet (Plain)

25500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8.3.1(Adhesion )	-	2000	Rs.25500/-, FOR - Corrosive resistance test @15/- per hour extra, Humidity resistance test @Rs.15/- per hour extra
Cl 8.3.2(Impact Resistance)	-	1500	Rs.25500/-, FOR - Corrosive resistance test @15/- per hour extra, Humidity resistance test @Rs.15/- per hour extra
Cl 8.4(Load Resistance)	-	1500	Rs.25500/-, FOR - Corrosive resistance test @15/- per hour extra, Humidity resistance test @Rs.15/- per hour extra
Cl 8.5(Scratch Resistance)	-	1500	Rs.25500/-, FOR - Corrosive resistance test @15/- per hour extra, Humidity resistance test @Rs.15/- per hour extra
Cl 8.7(Dry Film Thickness)	-	500	Rs.25500/-, FOR - Corrosive resistance test @15/- per hour extra, Humidity resistance test @Rs.15/- per hour extra
Cl 9.1(Workmanship)	-	500	Rs.25500/-, FOR - Corrosive resistance test @15/- per hour extra, Humidity resistance test @Rs.15/- per hour extra
Cl 10.1(Corrosion Test)	-	2000	Rs.25500/-, FOR - Corrosive resistance test @15/- per hour extra, Humidity resistance test @Rs.15/- per hour extra
Cl 10.2(Humidity Test)	-	4500	Rs.25500/-, FOR - Corrosive resistance test @15/- per hour extra, Humidity resistance test @Rs.15/- per hour extra
Cl 11(Length, Width & Thickness)	-	1500	Rs.25500/-, FOR - Corrosive resistance test @15/- per hour extra, Humidity resistance test @Rs.15/- per hour extra
Cl 12(Camber, Deviation From Squareness (Out-of- Square) & Deviation From Flatness)	-	1500	Rs.25500/-, FOR - Corrosive resistance test @15/- per hour extra, Humidity resistance test @Rs.15/- per hour extra
Cl 8.3.1(Adhesion )	-	1000	Rs.25500/-, FOR - Corrosive resistance test @15/- per hour extra, Humidity resistance test @Rs.15/- per hour extra
Cl 8.3.2(Impact Resistance)	-	1000	Rs.25500/-, FOR - Corrosive resistance test @15/- per hour extra, Humidity resistance test @Rs.15/- per hour extra
Cl 10.2(Humidity Test)	-	1000	Rs.25500/-, FOR - Corrosive resistance test @15/- per hour extra, Humidity resistance test @Rs.15/- per hour extra
Cl 11(Length, Width & Thickness)	-	1500	Rs.25500/-, FOR - Corrosive resistance test @15/- per hour extra, Humidity resistance test @Rs.15/- per hour extra
Cl 12(Camber, Deviation From Squareness (Out-of- Square) & Deviation From Flatness)	-	1500	Rs.25500/-, FOR - Corrosive resistance test @15/- per hour extra, Humidity resistance test @Rs.15/- per hour extra
8.6(Solvent Resistance test)	-	1000	Rs.25500/-, FOR - Corrosive resistance test @15/- per hour extra, Humidity resistance test @Rs.15/- per hour extra
9.2(colour)	-	500	Rs.25500/-, FOR - Corrosive resistance test @15/- per hour extra, Humidity resistance test @Rs.15/- per hour extra
9.3(Gloss (60 Deg))	-	1000	Rs.25500/-, FOR - Corrosive resistance test @15/- per hour extra, Humidity resistance test @Rs.15/- per hour extra
Cl 10.1(Corrosion Test)	-	15	Rs.25500/-, FOR - Corrosive resistance test @15/- per hour extra, Humidity resistance test @Rs.15/- per hour extra
10.1(IS 9844)	-	15	Rs.25500/-, FOR - Corrosive resistance test @15/- per hour extra, Humidity resistance test @Rs.15/- per hour extra
7 & 7.3(ISO 2808)	-	2000	Rs.25500/-, FOR - Corrosive resistance test @15/- per hour extra, Humidity resistance test @Rs.15/- per hour extra
11.0(Thickness)	-	500	Rs.25500/-, FOR - Corrosive resistance test @15/- per hour extra, Humidity resistance test @Rs.15/- per hour extra

17 Jun, 2027

-
-

First
Prev
1
2
3
4
Next
Last

Bureau of Indian Standards

The National Standards Body of India

DELHI TEST HOUSE, Azadhpur

A-62/3, G T KARNAL ROAD INDUSTRIAL AREA, OPPOSITE HANS CINEMA, AZADPUR, DELHI 110033, Delhi, North, Delhi, 110033

9810442016 info@delhitesthouse.com

Scope List