BIS - LIMS (Laboratory Information Management System)

LUCID LABORATORIES PRIVATE LIMITED, HYDERABAD

PLOT NO.3, IDA,, BALANAGAR, HYDERABAD, Medchal Malkajgiri, Telangana, 500037

9848163346 info@lucidlabsindia.com

Scope List

Reset

74 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 10748 (2025)

Hot-Rolled Steel Strip for Welded Tubes and Pipes - Specification ( Third Revision)

7600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(Supply of Materials)	-	0	-
Cl-6(Manufacture)	-	0	-
Cl-7.1(Ladle Analysis)	-	0	-
Cl-7.2(Product Analysis)	-	0	-
Cl-7.3(Carbon Equivalent Value)	-	200	-
Cl-8.1(Number of Tensile Tests)	-	0	-
Cl-8.2(Tensile Test Pieces)	-	0	-
Cl-8.3(Tensile Test)	-	1000	-
Cl-8.3, Table-5 & 6(Tensile Strength, MPa)	-	0	-
Cl-8.3, Table-5 & 6(Yield Strength, MPa)	-	0	-
Cl-8.3, Table-5 & 6(Internal Diameter of Bend)	-	0	-
Cl-9.1(Number of Bend Tests)	-	0	-
Cl-9.2(Bend test)	-	1000	-
Cl-10(Re- Tests)	-	0	-
Cl-11(freedam from Defects)	-	500	-
Cl-12(Dimensions)	-	1000	-
Cl-13(Tolerances)	-	0	-
Cl-14(Calculation of Mass)	-	300	-
Cl-16(Marking)	-	0	-
Cl-7.1, 7.2, 7.3 & 7.4(Carbon)	-	200	-
Cl-7.1, 7.2, 7.3 & 7.4(Manganese)	-	200	-
Cl-7.1, 7.2, 7.3 & 7.4(Sulphur)	-	200	-
Cl-7.1, 7.2, 7.3 & 7.4(Phosphorus)	-	200	-
Cl-7.1, 7.2, 7.3 & 7.4(Carbon Equivalent Value (CEV))	-	0	-
Cl-7.1, 7.2, 7.3 & 7.4(silicon)	-	200	-
Cl-7.1, 7.2, 7.3 & 7.4(aluminium)	-	200	-
Cl-7.1, 7.2, 7.3 & 7.4(total aluminium)	-	0	-
Cl-7.1, 7.2, 7.3 & 7.4(Niobium)	-	200	-
Cl-7.1, 7.2, 7.3 & 7.4(Vanadium)	-	200	-
Cl-7.1, 7.2, 7.3 & 7.4(Titanium)	-	200	-
Cl-7.1, 7.2, 7.3 & 7.4(Nitrogen)	-	800	-
Cl-7.1, 7.2, 7.3 & 7.4(Copper)	-	200	-
Cl-7.1, 7.2, 7.3 & 7.4(Mo + Cr +W)	-	0	-
Cl-7.1, 7.2, 7.3 & 7.4(Mo)	-	200	-
Cl-7.1, 7.2, 7.3 & 7.4(Boron)	-	200	-
Cl-7.1, 7.2, 7.3 & 7.4(Nickel)	-	200	-
Cl-7.1, 7.2, 7.3 & 7.4(Chromium)	-	200	-
Cl-8.3, Table-5 & 6(Elongation at Gauge Length,)	-	0	-

19 Apr, 2028

-
included w.e.f 04.08.2026

IS 5872 (2025)

Steel strapping for packaging ( Third Revision)

9300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause. 5.0(Carbon)	-	200	-
Clause. 5.0(Silicon)	-	200	-
Clause. 5.0(Manganese)	-	200	-
Clause. 5.0(Sulphur)	-	200	-
Clause. 5.0(Phosphorus)	-	200	-
Clause. 5.0(Boron)	-	200	-
Clause. 5.0(Niobium)	-	200	-
Clause. 5.0(Vanadium)	-	200	-
Clause. 5.0(Titanium)	-	200	-
Clause. 6.0(Tensile Test)	-	750	-
Clause. 6.0(Elongation test)	-	0	-
Clause. 7.0(Reverse Bend Test)	-	750	-
Clause. 8.0(Retest)	-	0	-
Clause. 9.0(Freedom From Defects)	-	250	-
Clause.10.0(Dimension , Shape & Tolerance)	-	500	-
Clause.11.0(Surface Finish)	-	500	-
Clause.12.0(Corrosion Resistance)	-	4000	-
Clause.13.0(Packing)	-	0	-
Clause.14.0(Marking)	-	0	-
Cl-10.1(Nominal Dimensions)	-	0	-
Cl-10.2(Dimension Tolerances)	-	0	-
Cl-10.3(Shape Tolerances)	-	0	-
Cl-10.4(Weld)	-	750	-
Cl-10.5(Coil Inside Diameter)	-	0	-

19 Apr, 2028

-
included w.e.f 15.09.2026.

IS 15410 (2025)

PLASTIC BOTTLES/CONTAINERS FOR PACKAGING OF NATURAL MINERAL WATER AND PACKAGED DRINKING WATER - SPECIFICATION (first revision)

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4.1.1(Materials for Primary Packaging (Container))	-	2000	-
Clause 4.1.2.1(Material for Closures (a) Closure materials (Aluminium))	-	0	-
Clause 4.1.2.1(Material for Closures (b) Plastic Materials)	-	0	-
Clause 4.1.2.1(Material for Closures (c) Combination of plastics and metal)	-	0	-
Clause 4.1.2.2(Materials for Primary Packaging-Closure colourants)	-	0	-
Clause 4.1.2.3(Materials for Primary Packaging-Sleeves for the closure)	-	0	-
Clause 4.1.3(Materials for Primary Packaging-Wad)	-	0	-
Clause 4.2(Design, Shape and Dimensions)	-	800	-
Clause 4.3("Manufacture, Workmanship, Finish and Appearance")	-	100	-
Clause 4.4(Capacity (Nominal))	-	500	-
Clause 4.4(Capacity (Brimfull))	-	0	-
Clause 4.5(Wall Thickness Top)	-	100	-
Clause 4.5(Wall Thickness Middle)	-	100	-
Clause 4.5(Wall Thickness Bottom)	-	100	-
Clause 4.6.1.1(Colour-Transparency)	-	500	-
Clause 4.6.1.2(Colour-Tint)	-	0	-
Clause 4.6.2(Leakage Test (Closure Leakage) cls. 6.1 of IS 2798)	-	0	-
Clause 4.6.2(Leakage Test (Vibration Leakage) cls. 6.2 of IS 2798)	-	500	-
Clause 4.6.3.1(Drop Impact test)	-	500	-
Clause 4.6.3.2(Stack Load test)	-	500	-
Clause 4.6.4.1(Overall Migration Container)	-	1000	-
Clause 4.6.4.1(Overall Migration Closure)	-	0	-
Clause 4.6.4.2(Specific Migration Container Barium)	-	400	-
Clause 4.6.4.2(Specific Migration Container Cobalt)	-	400	-
Clause 4.6.4.2(Specific Migration Container Copper)	-	400	-
Clause 4.6.4.2(Specific Migration Container Iron)	-	400	-
Clause 4.6.4.2(Specific Migration Container Lithium)	-	400	-
Clause 4.6.4.2(Specific Migration Container Manganese)	-	400	-
Clause 4.6.4.2(Specific Migration Container Zinc)	-	400	-
Clause 4.6.4.2(Specific Migration Container Antimony)	-	400	-
Clause 4.6.4.2(Specific Migration Container Phthalic acid, bis (2- ethylhexyl) ester (DEHP))	-	3000	-
Clause 4.6.4.2(Specific Migration Closure Barium)	-	400	-
Clause 4.6.4.2(Specific Migration Closure Cobalt)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Copper)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Iron)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Lithium)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Manganese)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Zinc)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Antimony)	-	0	-
Clause 4.6.4.2(Specific Migration Closure Phthalic acid, bis (2- ethylhexyl) ester (DEHP))	-	0	-
Clause 4.6.4.3(Colour migration Container)	-	500	-
Clause 4.6.4.3(Colour migration Closure)	-	0	-
Clause 4.6.5(Water Potability Test (Taste))	-	100	-
Clause 4.6.5(Water Potability Test (odour))	-	100	-
Clause 5.1(Marking)	-	0	-

19 Apr, 2028

-
Included w.e.f. 18.08.2026

IS 1875 (2025)

Steel Ingots, Billets, Blooms, Slabs and Bars For Forging - Specification (Sixth Revision)

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 6(Freedom From Defects)	-	200	-
Clause 7.1, 7.2 & 7.4, Table 1(C)	-	200	-
Clause 7.1, 7.2 & 7.4, Table 1(Si)	-	200	-
Clause 7.1, 7.2 & 7.4, Table 1(Mn)	-	200	-
Clause 7.1, 7.2 & 7.4, Table 1(Ni)	-	200	-
Clause 7.1, 7.2 & 7.4, Table 1(Cr)	-	200	-
Clause 7.1, 7.2 & 7.4, Table 1(Mo)	-	200	-
Clause 7.1, 7.2 & 7.4, Table 1(V)	-	200	-
Clause 7.1, 7.2 & 7.4, Table 1(Ala)	-	200	-
Clause 7.1, 7.2 & 7.4, Table 1(Cu)	-	200	-
Clause 7.1, 7.2 & 7.4, Table 1(Sb, Max)	-	200	-
Clause 7.1, 7.2 & 7.4, Table 1(P, Max)	-	200	-
Clause 7.4(Check Analysis)	-	0	-
Clasue -8(Dimensional Tolerances)	-	1000	-
Clause 8.2(Billets, blooms and slabs)	-	0	-
Clause 8.3(length of billets, blooms and slabs)	-	0	-
Clause 9(Conditions of Delivery)	-	0	-
Clause - 10.1, Table 4(Tensile Strength Min (MPa))	-	1000	-
Clause - 10.1, Table 4(Yield Strength Min (MPa))	-	0	-
Clause - 10.1, Table 4(Elongation (GL = 5.65√So) Min, Percent)	-	0	-
Clause - 10.1, Table 4(Normalizing Temperature (oC))	-	0	-
Clause - 10.2(Hardness Test)	-	500	-
Clause - 10.3(Hardenability Test)	-	2000	-
Clause 10.4(Grain Size)	-	800	-
Clause-12(Retests)	-	0	-
Clause 13.1(Hot Upset Test)	-	0	-
Clause -13.3(Decarburization Depth)	-	800	-
Clause-13.4(Bend Test)	-	500	-
Clause 13.5 (a)(Blue fracture Test)	-	1000	-
Clause 13.5 (b)(Step machined test)	-	0	-
Clause 13.5 (c)(Magnetic particle inspection)	-	0	-
Clause 13.5 (d)(Macrostreak flaw test)	-	0	-
Clause-13.6(Other Tests- Ultrasonic test)	-	1000	-
Clause-14(Marking)	-	0	-

19 Apr, 2028

-
Included w.e.f. 18.08.2026

IS 737 (2024)

WROUGHT ALUMINIUM AND ALUMINIUM ALLOY SHEET AND STRIP FOR GENERAL ENGINEERING PURPOSES SPECIFICATION (Fifth Revision)

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 4(Ordering Information - IS 737)	-	0	-
Cl. 4 (a)(Grade/ Thickness - IS 737)	-	0	-
Cl. 4 (b)(Condition - IS 737)	-	0	-
Cl. 4 (c)(Quantity in Kg - IS 737)	-	0	-
Cl. 4 (d)(Size - Thickness X Width X Length (T X W X L) in mm for sheets and (T X W) in mm for Strips/ Coils - IS 737)	-	0	-
Cl. 4 (e)(Coil ID and Coil Weight for Strips/ Coils - IS 737)	-	0	-
Cl. 4 (f)(Core/ Spool Requirement for Coils - IS 737)	-	0	-
Cl. 4 (g)(Packing Mode - IS 737)	-	0	-
Cl. 5(Supply for Material - IS 737/ IS 10259)	-	0	-
Cl. 6(Freedom from Defects - IS 737)	-	500	-
Cl. 7(Chemical Composition - IS 504/ IS 504 (Part-1 to 12)/ IS 504 (Part-13 to 16)/ ASTM E 1251/ IS 11035)	-	3000	-
Cl. 7(Si - IS 504 (Part-1)/ ASTM E 1251/ IS 11035)	-	0	-
Cl. 7(Fe - IS 504 (Part-2)/ ASTM E 1251/ IS 11035)	-	0	-
Cl. 7(Cu - IS 504 (Part-3)/ ASTM E 1251/ IS 11035)	-	0	-
Cl. 7(Mn - IS 504 (Part-5)/ ASTM E 1251/ IS 11035)	-	0	-
Cl. 7(Mg - IS 504 (Part-6)/ ASTM E 1251/ IS 11035)	-	0	-
Cl. 7(Cr - IS 504 (Part-8)/ ASTM E 1251/ IS 11035)	-	0	-
Cl. 7(Zn - IS 504 (Part-4)/ ASTM E 1251/ IS 11035)	-	0	-
Cl. 7(Ti - IS 504 (Part-11)/ ASTM E 1251/ IS 11035)	-	0	-
Cl. 7(Others (Each) - IS 504/ IS 504 (Part-1 to 12)/ IS 504 (Part-13 to 16)/ ASTM E 1251/ IS 11035)	-	0	-
Cl. 7(Others (Total) - IS 504/ IS 504 (Part-1 to 12)/ IS 504 (Part-13 to 16)/ ASTM E 1251/ IS 11035)	-	0	-
Cl. 7(Al - IS 504)	-	0	-
Cl. 8(Mechanical Properties - IS 1608 (Part-1))	-	0	-
Cl. 8.1(0.2% Proof Stress - IS 1608 (Part-1))	-	0	-
Cl. 8.1(Tensile Strength - IS 1608 (Part-1))	-	4200	-
Cl. 8.1(Elongation on 50mm Gauge Length - IS 1608 (Part-1))	-	0	-
Cl. 8.2(Bend Test - IS 1599)	-	1000	-
Cl. 9(Condition - IS 737/ IS 5052)	-	0	-
Cl. 10(Dimensions and Tolerances - IS 737/ IS 2676)	-	1000	-
Cl. 11(Selection of Test Samples - IS 737)	-	0	-
Cl. 11.1(Sheet and Strip of Aluminium or Non - Heat Treatable Aluminium Alloy - IS 737)	-	0	-
Cl. 11.2(Sheet and Strip of Heat - Treatable Aluminium Alloys - IS 737)	-	0	-
Cl. 12(Retests - IS 737/ IS 10259)	-	0	-
Cl. 13(Packaging - IS 737/ IS 10259)	-	0	-
Cl. 13.1(Marking - IS 737)	-	0	-
Cl. 4(Ordering Information - IS 737)	-	0	-
Cl. 4 (a)(Grade/ Thickness - IS 737)	-	0	-
Cl. 4 (b)(Condition - IS 737)	-	0	-
Cl. 4 (c)(Quantity in Kg - IS 737)	-	0	-
Cl. 4 (d)(Size - Thickness X Width X Length (T X W X L) in mm for sheets and (T X W) in mm for Strips/ Coils - IS 737)	-	0	-
Cl. 4 (e)(Coil ID and Coil Weight for Strips/ Coils - IS 737)	-	0	-
Cl. 4 (f)(Core/ Spool Requirement for Coils - IS 737)	-	0	-
Cl. 4 (g)(Packing Mode - IS 737)	-	0	-
Cl. 5(Supply for Material - IS 737/ IS 10259)	-	0	-
Cl. 6(Freedom from Defects - IS 737)	-	0	-
Cl. 7(Chemical Composition - IS 504/ IS 504 (Part-1 to 12)/ IS 504 (Part-13 to 16)/ ASTM E 1251/ IS 11035)	-	0	-
Cl. 7(Si - IS 504 (Part-1)/ ASTM E 1251/ IS 11035)	-	0	-
Cl. 7(Fe - IS 504 (Part-2)/ ASTM E 1251/ IS 11035)	-	0	-
Cl. 7(Cu - IS 504 (Part-3)/ ASTM E 1251/ IS 11035)	-	0	-
Cl. 7(Mn - IS 504 (Part-5)/ ASTM E 1251/ IS 11035)	-	0	-
Cl. 7(Mg - IS 504 (Part-6)/ ASTM E 1251/ IS 11035)	-	0	-
Cl. 7(Cr - IS 504 (Part-8)/ ASTM E 1251/ IS 11035)	-	0	-
Cl. 7(Zn - IS 504 (Part-4)/ ASTM E 1251/ IS 11035)	-	0	-
Cl. 7(Ti - IS 504 (Part-11)/ ASTM E 1251/ IS 11035)	-	0	-
Cl. 7(Others (Each) - IS 504/ IS 504 (Part-1 to 12)/ IS 504 (Part-13 to 16)/ ASTM E 1251/ IS 11035)	-	0	-
Cl. 7(Others (Total) - IS 504/ IS 504 (Part-1 to 12)/ IS 504 (Part-13 to 16)/ ASTM E 1251/ IS 11035)	-	0	-
Cl. 7(Al - IS 504)	-	0	-
Cl. 8(Mechanical Properties - IS 1608 (Part-1))	-	0	-
Cl. 8.1(0.2% Proof Stress - IS 1608 (Part-1))	-	0	-
Cl. 8.1(Tensile Strength - IS 1608 (Part-1))	-	0	-
Cl. 8.1(Elongation on 50mm Gauge Length - IS 1608 (Part-1))	-	0	-
Cl. 8.2(Bend Test - IS 1599)	-	0	-
Cl. 9(Condition - IS 737/ IS 5052)	-	0	-
Cl. 10(Dimensions and Tolerances - IS 737/ IS 2676)	-	0	-
Cl. 11(Selection of Test Samples - IS 737)	-	0	-
Cl. 11.1(Sheet and Strip of Aluminium or Non - Heat Treatable Aluminium Alloy - IS 737)	-	0	-
Cl. 11.2(Sheet and Strip of Heat - Treatable Aluminium Alloys - IS 737)	-	0	-
Cl. 12(Retests - IS 737/ IS 10259)	-	0	-
Cl. 13(Packaging - IS 737/ IS 10259)	-	0	-
Cl. 13.1(Marking - IS 737)	-	0	-

19 Apr, 2028

-
Included w.e.f. 18.08.2026

IS 733 (2025)

Wrought Aluminium and Aluminium Alloy Bars, Rods, Sections, Extruded Tube, Hollow Sections and Profiles for General Engineering Purposes ? Specification (Fourth Revision)

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 6 Table 1 - Table 8(Sodium)	-	200	-
Cl. 6 Table 1 - Table 8(Strontium)	-	200	-
Cl. 6 Table 1 - Table 8(Antimony)	-	200	-
Cl. 6 Table 1 - Table 8(Phosphorus)	-	200	-
Cl. 6 Table 1 - Table 8(Zirconium +Titanium)	-	200	-
Cl-4(General requirements)	-	0	-
Cl-6.1, Table-1 to 8(Fe)	-	200	-
Cl-6.1, Table-1 to 8(Cu)	-	200	-
Cl-6.1, Table-1 to 8(Mn)	-	200	-
Cl-6.1, Table-1 to 8(Mg)	-	200	-
Cl-6.1, Table-1 to 8(Cr)	-	200	-
Cl-6.1, Table-1 to 8(Zn)	-	200	-
Cl-6.1, Table-1 to 8(Ti)	-	200	-
Cl-6.1, Table-1 to 8(V)	-	200	-
Cl-6.1, Table-1 to 8(Aluminium)	-	200	-
Cl-6.2(chemical analysis)	-	0	-
Cl-7.1, 7.2 & 7.3, Table-9(Dimensions)	-	0	-
Cl-7.1, 7.2 & 7.3, Table-9(Rm MPa)	-	0	-
Cl-7.1, 7.2 & 7.3, Table-9(Rp0.2 MPa)	-	0	-
Cl-7.1, 7.2 & 7.3, Table-9(Elongation , Percent)	-	0	-
Cl-9(Dimensions and Tolerances)	-	800	-
Cl-12(Packaging and Marking)	-	0	-
Cl-7.1(Tensile test)	-	3500	-
Cl-5(Freedom from Defects)	-	200	-
Cl-6.1, Table-1 to 8(Si)	-	200	-

19 Apr, 2028

-
Included w.e.f. 18.08.2026

IS 12592 (2002)

Precast concrete manhole cover and frame - Specification (First Revision)

12400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Grade)	-	100	-
3(Type/Shape of Cover)	-	100	-
4.4(Reinforcement)	-	3000	-
4.5(Steel Fibres - Diameter / equivalent diameterofsteel tibres)	-	250	-
4.5(Steel Fibres - The aspect ratio of the tibres)	-	0	-
5.2 and Table 1(Dimensions of Frame - A)	-	200	-
5.2 and Table 1(Dimensions of Frame - B)	-	200	-
5.2 and Table 1(Dimensions of Frame - C)	-	200	-
5.2 and Table 1(Dimensions of Frame - D)	-	200	-
5.2 and Table 1(Dimensions of Frame - E)	-	200	-
5.2 and Table 1(Dimensions of Frame - F)	-	200	-
5.2(Dimensions of cover- Diameter)	-	100	-
5.2(Clearance at top between the frame and the cover all round the periphery)	-	50	-
5.2(Top surface ofthe frame and cover is in level)	-	100	-
5.2(Suitable taper matching with taper given for the frame shall be provided to the periphery of the cover)	-	100	-
5.2 and Fig 1(Clear cover to reinforcement)	-	100	-
5.2 and Fig 1(Distance of housing from the edge)	-	100	-
7.4.1(Edge Protection and Finishing - Frame)	-	200	-
7.4.1(Edge Protection and Finishing - Frame)	-	0	-
7.4.1(Edge Protection and Finishing - Frame)	-	0	-
7.4.1(Edge Protection and Finishing - Frame)	-	0	-
7.4.2(Edge Protection and Finishing - Cover)	-	200	-
7.4.2(Edge Protection and Finishing - Cover)	-	0	-
7.4.2(Edge Protection and Finishing - Cover)	-	0	-
7.4.2(Edge Protection and Finishing - Cover)	-	0	-
8(LIFTING HOOKS)	-	200	-
8(LIFTING HOOKS)	-	0	-
9.1(General)	-	0	-
9.3 and Table and Annex C(Load Test)	-	6000	-
Clause No. 5.2, Figure 1(Typical Illustration of circular precast concrete manhole cover)	-	0	-
Clause No. 9.3 Annex C(Adhesion between concrete and reinforcing steel)	-	0	-
Clause No. 9.3 Annex C(Cracks at bottom side of the cover )	-	0	-
Clause No. 9.3 Annex C(Permanent set of cover)	-	0	-
Clause No. 9.3, 12.3 & C-1.1, Table No. 2(2/3rd of Test Load)	-	0	-
Clause No. 9.3, 12.3 & C-1.1, Table No. 2(Test Load)	-	0	-
Clause No. 8(Lifting Device)	-	0	-
Clause No. 8(Lifting Hooks (Diameter of MS rod))	-	200	-
Clause No. 7.4.4(Compatitbilty of Seating of cover and frame)	-	200	-
Clause No. 7.4.2(Edge protection and finishing of cover (Thikness of MS sheet))	-	200	-
Clause No. 7.4.2(Edge protection and finishing of cover (Cover finish of top surface))	-	0	-
Clause No. 7.4.1(Edge protection and finishing of frame (Steel connectors))	-	0	-
Clause No. 7.4.1(Edge protection and finishing of frame (Size of mild steel flat))	-	0	-
Clause No. 6(Design)	-	0	-
4.4(Reinforcement)	-	0	-

19 Apr, 2028

-
Included w.e.f. 18.08.2026

IS 2062 (Part 2) (2026)

Structural Steel - Part 2 - Hot Rolled Quenched and Tempered Steel Plates, Sheets, Strips and Wide Flats

16800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(General requirements)	-	0	-
Cl-6(Manufacture )	-	0	-
Cl-7.1(Ladle Analysis (Heat Analysis))	-	0	-
Cl-7.1 & 7.3, Table 1 (C (S Grades ))	-	0	-
Cl-7.1 & 7.3, Table 1 (Mn (S Grades ))	-	0	-
Cl-7.1 & 7.3, Table 1 (S (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (P (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (Si (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (Cr (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (Ni (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (Mo (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (N (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (B (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (Cu (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (Nb (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (Ti (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (V (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (Zr (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (Aluminium (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 2(C (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(Mn (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(S (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(P (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(Si (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(Cu (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(Ni (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(Cr (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(Mo (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(V (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(Nb (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(Ti (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(B (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(Zr (SG Grades))	-	0	-
Cl-7.2, Table 3 (i)(Carbon)	-	200	-
Cl-7.2, Table 3 (ii)(Silicon)	-	200	-
Cl-7.2, Table 3 (iii)(Manganese)	-	200	-
Cl-7.2, Table 3 (iv)(Phosphorus)	-	200	-
Cl-7.2, Table 3 (v)(Sulphur)	-	200	-
Cl-7.2, Table 3 (vi)(Vanadium)	-	200	-
Cl-7.2, Table 3 (vii)(Niobium)	-	200	-
Cl-7.2, Table 3 (viii)(Boron)	-	200	-
Cl-7.2, Table 3 (ix)(Titanium)	-	200	-
Cl-7.2, Table 3 (x)(Copper)	-	200	-
Cl-7.2, Table 3 (xi)(Nickel)	-	200	-
Cl-7.2, Table 3 (xii)(Chromium)	-	200	-
Cl-7.2, Table 3 (xiii)(Molybdenum)	-	200	-
Cl-7.2, Table 3 (xiv)(Zirconium)	-	200	-
Cl-7.2, Table 3 (xv)(Nitrogen)	-	1500	-
Cl-7.2, Table-4 (i)(Carbon)	-	0	-
Cl-7.2, Table-4 (ii)(Silicon)	-	0	-
Cl-7.2, Table-4 (iii)(Manganese)	-	0	-
Cl-7.2, Table-4 (iv)(Phosphorus)	-	0	-
Cl-7.2, Table-4 (v)(Sulphur)	-	0	-
Cl-7.2, Table-4 (vi)(Vanadium)	-	0	-
Cl-7.2, Table-4 (vii)(Niobium)	-	0	-
Cl-7.2, Table-4 (viii)(Boron)	-	0	-
Cl-7.2, Table-4 (ix)(Titanium)	-	0	-
Cl-7.2, Table-4 (x)(Copper)	-	0	-
Cl-7.2, Table-4 (xi)(Nickel)	-	0	-
Cl-7.2, Table-4 (xii)(Chromium)	-	0	-
Cl-7.2, Table-4 (xiii)(Molybdenum)	-	0	-
Cl-7.2, Table-4 (xiv)(Zirconium)	-	0	-
Cl-7.2, Table-4 (xv)(Nitrogen)	-	0	-
Cl-7.3 & 7.4(Carbon Equivalent Value (CE))	-	200	-
Cl-8.1 & 8.4, Table 7(Minimum Yield Strength ReH, MPa Nominal Thickness,-≥3 ≤ 50)	-	0	-
Cl-8.1 & 8.4, Table 7(Minimum Yield Strength ReH, MPa Nominal Thickness,-> 50 ≤ 100)	-	0	-
Cl-8.1 & 8.4, Table 7(Minimum Yield Strength ReH, MPa Nominal Thickness,-> 100 ≤ 125)	-	0	-
Cl-8.1 & 8.4, Table 7(Minimum Yield Strength ReH, MPa Nominal Thickness,-> 125 ≤ 200)	-	0	-
Cl-8.1 & 8.4, Table 7(Tensile Strength Rm , MPa Nominal Thickness- ≥ 3 ≤ 50)	-	0	-
Cl-8.1 & 8.4, Table 7(Tensile Strength Rm , MPa Nominal Thickness- > 50 ≤ 100)	-	0	-
Cl-8.1 & 8.4, Table 7(Tensile Strength Rm , MPa Nominal Thickness- > 100 ≤ 125 )	-	0	-
Cl-8.1 & 8.4, Table 7(Tensile Strength Rm , MPa Nominal Thickness- > 125 ≤ 200)	-	0	-
Cl-8.1 & 8.4, Table 7(Elongation A, Percentage Min at Gauge Length, Lo = 5.65√So- ≥ 3 ≤ 200)	-	0	-
Cl-8.2(Location of Samples and Orientation of Test Pieces)	-	0	-
Cl-8.3(Tensile Test Pieces)	-	0	-
Cl-8.4(Tensile Test)	-	2000	-
Cl-9 & 9.4(Transverse Charpy V-notch properties a,c S Grades)	-	2500	-
Cl-9 & 9.4(Longitudinal Charpy V-notch properties SG Grades)	-	2500	-
Cl-9.1(Preparation of Impact Test Pieces (V-notch test))	-	1500	-
Cl-10.1(Weldability)	-	1500	-
Cl-10.2.1(Hot-Forming)	-	0	-
Cl-10.2.2(Cold Formability)	-	0	-
Cl-10.2.3(Flangeability)	-	800	-
Cl-10.3(Hot-Dip Zinc-Coating)	-	1000	-
Cl-11(Internal Soundness (Ultrasonic testing))	-	1500	-
Cl-12.1(Re-Tests )	-	0	-
Cl-12.2(Re-Heat Treatment)	-	0	-
Cl-13(Freedom From Defect)	-	200	-
Cl-14(Dimensions )	-	1000	-
Cl-15(Tolerances)	-	0	-
Cl-16(Calculation of Mass )	-	200	-
Cl-18(Marking and Packing )	-	100	-

19 Apr, 2028

-
Included w.e.f. 18.08.2026

IS 2062 (Part 1) (2025)

Structural Steel - Part 1 - Hot Rolled Medium and High tensile Steel

10500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-6(MANUFACTURE)	-	50	-
Cl-7(FREEDOM FROM DEFECTS)	-	150	-
Cl-8.1(Ladle Analysis)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis-C)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Mn)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- S)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- P)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Si )	-	0	-
Cl-8.1 & 8.2, Table-1(Carbon Equivalen t (CE), Max)	-	200	-
Cl-8.1 & 8.2, Note-1(Total aluminium)	-	200	-
Cl-8.1 & 8.2, Note-5(Nb)	-	200	-
Cl-8.1 & 8.2, Note-5(V)	-	200	-
Cl-8.1 & 8.2, Note-5(Ti)	-	200	-
Cl-8.1 & 8.2, Note-6(B)	-	200	-
Cl-8.2, Table 2 (i)(Carbon)	-	200	-
Cl-8.2, Table 2 (ii)(Manganese)	-	200	-
Cl-8.2, Table 2 (iii)(Sulphur)	-	200	-
Cl-8.2, Table 2 (iv)(Phosphorus)	-	200	-
Cl-8.2, Table 2 (v)(Silicon)	-	200	-
Cl-8.2, Table 2 (vi)(Copper)	-	200	-
Cl-8.2, Table 2 (vii)(Vanadium)	-	0	-
Cl-8.2, Table 2 (viii)(Niobium)	-	0	-
Cl-8.2, Table 2 (ix)(Titanium)	-	0	-
Cl-8.2, Table 2 (x)(Nitrogen)	-	1500	-
Cl-10.1(Number of Tensile Tests)	-	0	-
Cl-10.2(Tensile Test Pieces)	-	400	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Tensile Strength Rm, Min MPa7)	-	700	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Yield Stress ReH, Min MPa7)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Percentage Elongation A, Min at Gauge Length, L0=5.65√So)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Internal Bend Diameter Max)	-	500	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test-Temp°C)	-	2500	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test- Min J)	-	2500	-
Cl-11.1(Number of Bend Tests)	-	0	-
Cl-11.2(Bend Test Piece)	-	0	-
Cl-11.3(Bend Test )	-	0	-
Cl-12(Impact Test )	-	0	-
Cl-14, Table-4 (i)(Beam, column, channel and angle sections including parallel beam and column sections)	-	1000	-
Cl-14, Table-4 (ii)(Tee bars)	-	0	-
Cl-14, Table-4 (iii)(Bulb angles)	-	0	-
Cl-14, Table-4 (iv)(Plates, sheets, strips and flats)	-	0	-
Cl-14, Table-4 (vi)(Round and square bars)	-	0	-
Cl-14, Table-4 (vii)(Bulb flats)	-	0	-
Cl-14, Table-4 (viii)(Sheet piling sections)	-	0	-
Cl-14, Table-4 (ix)(Channel sections)	-	0	-
Cl-13(Other TestsNondestructive testing, Metallurgical tests )	-	2000	-
Cl-13.3(Strength of joint )	-	700	-
Cl-15(Tolerances)	-	0	-
Cl-16.1(Retests)	-	0	-
Cl-16.2(Re-heat Treatment)	-	0	-
Cl-6(MANUFACTURE)	-	0	-
Cl-7(FREEDOM FROM DEFECTS)	-	0	-
Cl-8.1(Ladle Analysis)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis-C)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Mn)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- S)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- P)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Si )	-	0	-
Cl-8.1 & 8.2, Table-1(Carbon Equivalen t (CE), Max)	-	0	-
Cl-8.1 & 8.2, Note-1(Total aluminium)	-	0	-
Cl-8.1 & 8.2, Note-5(Nb)	-	0	-
Cl-8.1 & 8.2, Note-5(V)	-	0	-
Cl-8.1 & 8.2, Note-5(Ti)	-	0	-
Cl-8.1 & 8.2, Note-6(B)	-	0	-
Cl-8.2, Table 2 (i)(Carbon)	-	0	-
Cl-8.2, Table 2 (ii)(Manganese)	-	0	-
Cl-8.2, Table 2 (iii)(Sulphur)	-	0	-
Cl-8.2, Table 2 (iv)(Phosphorus)	-	0	-
Cl-8.2, Table 2 (v)(Silicon)	-	0	-
Cl-8.2, Table 2 (vi)(Copper)	-	0	-
Cl-8.2, Table 2 (vii)(Vanadium)	-	0	-
Cl-8.2, Table 2 (viii)(Niobium)	-	0	-
Cl-8.2, Table 2 (ix)(Titanium)	-	0	-
Cl-8.2, Table 2 (x)(Nitrogen)	-	0	-
Cl-10.1(Number of Tensile Tests)	-	0	-
Cl-10.2(Tensile Test Pieces)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Tensile Strength Rm, Min MPa7)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Yield Stress ReH, Min MPa7)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Percentage Elongation A, Min at Gauge Length, L0=5.65√So)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Internal Bend Diameter Max)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test-Temp°C)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test- Min J)	-	0	-
Cl-11.1(Number of Bend Tests)	-	0	-
Cl-11.2(Bend Test Piece)	-	0	-
Cl-11.3(Bend Test )	-	0	-
Cl-12(Impact Test )	-	0	-
Cl-14, Table-4 (i)(Beam, column, channel and angle sections including parallel beam and column sections)	-	0	-
Cl-14, Table-4 (ii)(Tee bars)	-	0	-
Cl-14, Table-4 (iii)(Bulb angles)	-	0	-
Cl-14, Table-4 (iv)(Plates, sheets, strips and flats)	-	0	-
Cl-14, Table-4 (vi)(Round and square bars)	-	0	-
Cl-14, Table-4 (vii)(Bulb flats)	-	0	-
Cl-14, Table-4 (viii)(Sheet piling sections)	-	0	-
Cl-14, Table-4 (ix)(Channel sections)	-	0	-
Cl-13(Other TestsNondestructive testing, Metallurgical tests )	-	0	-
Cl-13.3(Strength of joint )	-	0	-
Cl-15(Tolerances)	-	0	-
Cl-16.1(Retests)	-	0	-
Cl-16.2(Re-heat Treatment)	-	0	-
Cl-6(MANUFACTURE)	-	0	-
Cl-7(FREEDOM FROM DEFECTS)	-	0	-
Cl-8.1(Ladle Analysis)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis-C)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Mn)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- S)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- P)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Si )	-	0	-
Cl-8.1 & 8.2, Table-1(Carbon Equivalen t (CE), Max)	-	0	-
Cl-8.1 & 8.2, Note-1(Total aluminium)	-	0	-
Cl-8.1 & 8.2, Note-5(Nb)	-	0	-
Cl-8.1 & 8.2, Note-5(V)	-	0	-
Cl-8.1 & 8.2, Note-5(Ti)	-	0	-
Cl-8.1 & 8.2, Note-6(B)	-	0	-
Cl-8.2, Table 2 (i)(Carbon)	-	0	-
Cl-8.2, Table 2 (ii)(Manganese)	-	0	-
Cl-8.2, Table 2 (iii)(Sulphur)	-	0	-
Cl-8.2, Table 2 (iv)(Phosphorus)	-	0	-
Cl-8.2, Table 2 (v)(Silicon)	-	0	-
Cl-8.2, Table 2 (vi)(Copper)	-	0	-
Cl-8.2, Table 2 (vii)(Vanadium)	-	0	-
Cl-8.2, Table 2 (viii)(Niobium)	-	0	-
Cl-8.2, Table 2 (ix)(Titanium)	-	0	-
Cl-8.2, Table 2 (x)(Nitrogen)	-	0	-
Cl-10.1(Number of Tensile Tests)	-	0	-
Cl-10.2(Tensile Test Pieces)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Tensile Strength Rm, Min MPa7)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Yield Stress ReH, Min MPa7)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Percentage Elongation A, Min at Gauge Length, L0=5.65√So)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Internal Bend Diameter Max)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test-Temp°C)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test- Min J)	-	0	-
Cl-11.1(Number of Bend Tests)	-	0	-
Cl-11.2(Bend Test Piece)	-	0	-
Cl-11.3(Bend Test )	-	0	-
Cl-12(Impact Test )	-	0	-
Cl-14, Table-4 (i)(Beam, column, channel and angle sections including parallel beam and column sections)	-	0	-
Cl-14, Table-4 (ii)(Tee bars)	-	0	-
Cl-14, Table-4 (iii)(Bulb angles)	-	0	-
Cl-14, Table-4 (iv)(Plates, sheets, strips and flats)	-	0	-
Cl-14, Table-4 (vi)(Round and square bars)	-	0	-
Cl-14, Table-4 (vii)(Bulb flats)	-	0	-
Cl-14, Table-4 (viii)(Sheet piling sections)	-	0	-
Cl-14, Table-4 (ix)(Channel sections)	-	0	-
Cl-13(Other TestsNondestructive testing, Metallurgical tests )	-	0	-
Cl-13.3(Strength of joint )	-	0	-
Cl-15(Tolerances)	-	0	-
Cl-16.1(Retests)	-	0	-
Cl-16.2(Re-heat Treatment)	-	0	-

19 Apr, 2028

-
Included w.e.f. 18.08.2026

IS 5872 (1990)

Cold rolled steel strips (Box Strappings) - Specification

COLD ROLLED STEEL STRIPS (BOX STRAPPINGS)

5800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 9(Workmanship)	-	100	-
Cl 10(Width & Thickness)	-	100	-
Cl 12(Coating)	-	100	-
Cl. 10.2(Thickness)	-	100	-
Cl. 6 Table 3(Elongation at 50 mm gauge length)	-	800	-
5.0 & 5.1 , Table 1 & 2(Carbon)	-	300	-
5.0 & 5.1 , Table 1 & 2(Manganese)	-	300	-
5.0 & 5.1 , Table 1 & 2(Sulphur)	-	300	-
5.0 & 5.1 , Table 1 & 2(Phosphorus)	-	300	-
5.0 & 5.1 , Table 1 & 2(Niobium)	-	300	-
5.0 & 5.1 , Table 1 & 2(Vanadium)	-	300	-
5.0 & 5.1 , Table 1 & 2(Titanium)	-	300	-
5.0 & 5.1 , Table 1 & 2(Boron)	-	300	-
5.0 & 5.1 , Table 1 & 2(Micro Alloying Elements)	-	300	-
6.0 & Table3(Tensile Strength - IS: 1608(P1))	-	300	-
10.0 & 10.2(Width -SOP MT-23)	-	300	-
12.0 & 12.1(Corrosion Resistance - IS 9844)	-	1000	-
Cl 7(Bending To Both Side At 90°, Then Straight)	-	300	-
Cl 6(UTM)	-	0	-
Cl 11(Workmanship)	-	0	-
Cl 6(UTM)	-	0	-
Cl 7(Bending To Both Side At 90°, Then Straight)	-	0	-
Cl 9(Workmanship)	-	0	-
Cl 10(Width & Thickness)	-	0	-
Cl 11(Workmanship)	-	0	-
Cl 12(Coating)	-	0	-
Cl 6(UTM)	-	0	-
Cl 7(Bending To Both Side At 90°, Then Straight)	-	0	-
Cl 9(Workmanship)	-	0	-
Cl 10(Width & Thickness)	-	0	-
Cl 11(Workmanship)	-	0	-
Cl 12(Coating)	-	0	-
Cl 12(Coating)	-	0	-
Cl 11(Workmanship)	-	0	-
Cl 10(Width & Thickness)	-	0	-
Cl 9(Workmanship)	-	0	-
Cl 7(Bending To Both Side At 90°, Then Straight)	-	0	-
Cl 6(UTM)	-	0	-
5(Chemical Composition)	-	0	-
Cl 6(UTM)	-	0	-
Cl 7(Bending To Both Side At 90°, Then Straight)	-	0	-
Cl 9(Workmanship)	-	0	-
Cl 10(Width & Thickness)	-	0	-
Cl 11(Workmanship)	-	0	-
Cl 12(Coating)	-	0	-
6.0 & Table3(Elongation on 50mm GL-IS: 1608(P1))	-	0	-
10.0 & 10.2(Thickness -SOP MT-23)	-	0	-
11.0 & 11.1(Surface finish - Visual)	-	0	-

19 Apr, 2028

-
-

IS 1161 (2014)

Steel tubes for structural purposes - Specification (Fifth Revision)

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5 AND AS PER IS 10748(CARBON)	-	300	-
Clause - 5.1, Table-3(SULPHUR)	-	300	-
Clause - 5.1, Table-3(PHOSPHURS)	-	300	-
Clause - 5.1, Table-3(MANGANESE)	-	300	-
Clause - 5.1, Table-3(SILICON)	-	300	-
Clause - 5.1, Table-3( ALUMINIUM)	-	300	-
5 AND AS PER IS 10748(CARBON EQUIVALENT)	-	300	-
5 AND AS PER IS 10748(MICRO ALLOY)	-	500	-
Cl 6(Outer Diameter, Thickness & Mass)	-	500	-
Cl 7(Workmanship)	-	500	-
8 AND AS PER IS 4736(MASS OF ZINC COATING)	-	1000	-
8 AND AS PER IS 4736(UNIFORMITY OF ZINC COATING)	-	1000	-
9(Straightness)	-	500	-
10(Lengths)	-	500	-
Cl 11(Tensile Test, Flattening Test & Cold Bend Test)	-	300	-
Cl. 11.2 Table 2(Yield strength)	-	250	-
Clause 11.2, Table -2(Elongation)	-	250	-
Cl 11.3.1(Cold bend test (upto & including 50 mm NB))	-	500	-
Cl 11.3.1(Flattening test (over 50 mm NB))	-	600	-

19 Apr, 2028

-
-

IS 15500 : Part 1 to 8 (2004)

Deepwell handpumps, components and special tools - Specification

97000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2/2.3,(Refer 15500(Part 1 to 8)& 5 (Part 1)(Raw material)	-	1000	NIL
2/2.3,(Refer 15500(Part 1 to 8)& 9.4 (Part 1)(Dimensions & critical dimensions in conformance with the relevant figures in Part 4.)	-	900	NIL
2/2.3,(Refer fig 4.1 of Part4) & 9.4 (Part 1)(Dimensions of FIG.4.1 HEAD— STANDARD(For SDWP, VLOM-65 and VLOM-50))	-	900	NIL
2/2.3,(Refer fig 4.2 of Part4)(Dimensions of FIG. 4,2 HEAD— EWDP)	-	900	NIL
2/2.3,(Refer fig 4.3A of Part4)(Dimensions of Fig 4.3A Side Plate)	-	900	NIL
2/2.3,(Refer fig 4.3B of Part4)(Dimensions of Fig 4.3B Head Flange)	-	900	NIL
2/2.3,(Refer fig 4.3C of Part4)(Dimensions of Fig 4.3C Back Plate —Standard (For SDWP, VLOM-65 & VLOM-50))	-	500	NIL
2/2.3,(Refer fig 4.3D of Part4)(Dimensions of Fig 4.3D Bracket — Standard (For SDWP, VLOM-65 & VLOM-50))	-	500	NIL
2/2.3,(Refer fig 4.3E of Part4)(Dimensions of Fig 4.3E Back Plate — EDWP)	-	500	NIL
2/2.3,(Refer fig 4.3F of Part4)(Dimensions of Fig 4.3F Bracket — EDWP)	-	500	NIL
2/2.3,(Refer fig 4.3G of Part4)(Dimensions of Fig 4.3G Axle Bust — Right)	-	500	NIL
2/2.3,(Refer fig 4.3H of Part4)(Dimensions of Fig 4.3H Axle Bust — Left)	-	500	NIL
2/2.3,(Refer fig 4.3I of Part4)(Dimensions of Fig 4.3 I Front Top End Plate)	-	500	NIL
2/2.3,(Refer fig 4.3IJof Part4)(Dimensions of 4.3J Front Bottom End Plate)	-	500	NIL
2/2.3,(Refer fig 4.3IKof Part4)(Dimensions of Fig 4.3K Gusset — Standard w (For SDWP, VLOM-65 & VLOM-50))	-	500	NIL
2/2.3,(Refer fig 4.3L Jof Part4)(Dimensions of Fig 4.3L Gusset — EDWP (For EDWP) )	-	500	NIL
2/2.3,(Refer fig 4.4 Jof Part4)(Dimensions of FIG. 4.4 FRONTCOVER)	-	500	NIL
2/2.3,(Refer fig 4.5A of Part4)(Dimensions of FIG. 4.5A Flange for Third Plate)	-	500	NIL
2/2.3,(Refer fig 4.5 B of Part4)(Dimensions of FIG. 4.5B Guide Bush )	-	500	NIL
2/2.3,(Refer fig 4.6 of Part4)(Dimensions of FIG.4.6 HANDLE— STANDARD (For SDWP, VLOM-65 & VLOM-50))	-	500	NIL
2/2.3,(Refer fig 4.7 of Part4)(Dimensions of FIG.4.7 HANDLE— EDWP)	-	500	NIL
2/2.3,(Refer fig 4.8A of Part4)(Dimensions of FIG 4.8A Handle Bar — Standard (For SDWR VLOM-65 & VLOM-50))	-	500	NIL
2/2.3,(Refer fig 4.8B of Part4)(Dimensions of FIG 4.8B Handle Bar — EDWP)	-	500	NIL
2/2.3,(Refer fig 4.8C of Part4)(Dimensions of FIG 4.8C Chain Guide)	-	500	NIL
2/2.3,(Refer fig 4.8 D of Part4)(Dimensions of Fig 4.8D Bearing Housing )	-	500	NIL
2/2.3,(Refer fig 4.9 of Part4)(Dimensions of FIG. 4.9 CHAIN WITH COUPLING)	-	850	NIL
2/2.3,(Refer fig 4.10 of Part4)(Dimensions of FIG. 4.10 T-BAR (For EDWP only))	-	850	NIL
2/2.3,(Refer fig 4.11 of Part4)(Dimensions of FIG; 4.11 COUNTER WEIGHT (For EDWP only))	-	850	NIL
2/2.3,(Refer fig 4.12A of Part4)(Dimensions of Fig 4.1 2A Telescopic Stand — Standard (For borewell with 150 NB casing pipe)(For SDWP, VLOM-65 & VLOM-50))	-	850	NIL
2/2.3,(Refer fig 4.12B of Part4)(Dimensions of Fig 4.12B Normal Stand — Standard (For borewell with 1001125 NB casing pipe) (For SDWP, VLOM-65 & VLOM-50))	-	850	NIL
2/2.3,(Refer fig 4.13A of Part4)(Dimensions of Fig 4.1 3A Telescopic Stand — EDWP (For borewell with 150 NB casing pipe) FOR EDWP )	-	850	NIL
2/2.3,(Refer fig 4.13B of Part4)(Dimensions of Fig 4.1 3B Normal Stand — EDWP (For borewell with 100/125 NB casing pipe) FOR EDWP )	-	850	NIL
2/2.3,(Refer fig 4.14 A of Part4)(Dimensions of Fig 4.1 4A Stand Pipe — Standard (For SDWP, VLOM-65, VLOM-50))	-	850	NIL
2/2.3,(Refer fig 4.14 B of Part4)(Dimensions of Fig 4.14B Stand Pipe — EDWP (For EDWP))	-	850	NIL
2/2.3,(Refer fig 4.14 C of Part4)(Dimensions of Fig 4.14C Stand Flange)	-	850	NIL
2/2.3,(Refer fig 4.14 D of Part4)(Dimensions of Fig 4.14D Leg)	-	850	NIL
2/2.3,(Refer fig 4.14 E of Part4)(Dimensions of Fig 4.14E Gusset)	-	850	NIL
2/2.3,(Refer fig 4.14 F of Part4)(Dimensions of Fig 4.1 4F Reducer Coller)	-	850	NIL
2/2.3,(Refer fig 4.14 G of Part4)(Dimensions of Fig 4.14G Spike)	-	850	NIL
2/2.3,(Refer fig 4.15 of Part4)(Dimensions of FIG, 4.15 WATER TANK — 32 (For SDWP & EDWP))	-	850	NIL
2/2.3,(Refer fig 4.16 of Part4)(Dimensions of FIG. 4.16 WATERTANK— 50)	-	850	NIL
2/2.3,(Refer fig 4.17 of Part4)(Dimensions of FIG. 4.17 WATERTANK— 65)	-	850	NIL
2/2.3,(Refer fig 4.18A of Part4)(Dimensions of FIG. 4.1 8A Tank Pipe )	-	850	NIL
2/2.3,(Refer fig 4.18B of Part4)(Dimensions of FIG. 4.18B Tank Top Flange)	-	850	NIL
2/2.3,(Refer fig 4.18C of Part4)(Dimensions of FIG. 4.18C Spout)	-	850	NIL
2/2.3,(Refer fig 4.18D of Part4)(Dimensions of FIG 4.1 8D Gusset)	-	500	NIL
2/2.3,(Refer fig 4.18E of Part4)(Dimensions of FIG 4.18E Tank Bottom Flanae — 32 (For SWDP & EDW~))	-	850	NIL
2/2.3,(Refer fig 4.18F of Part4)(Dimensions of FIG 4.1 8F Riser Pipe Holder — 32 (For SWDP & EDWP))	-	850	NIL
2/2.3,(Refer fig 4.18G of Part4)(Dimensions of FIG 4. 18G Riser Pipe Holder — 50)	-	850	NIL
2/2.3,(Refer fig 4.18H of Part4)(Dimensions of FIG 4.1 8H Tank Bottom Flange — 50)	-	850	NIL
2/2.3,(Refer fig 4.18I of Part4)(Dimensions of FIG 4.18I Tank Bottom Flange — 65 )	-	850	NIL
2/2.3,(Refer fig 4.18J of Part4)(Dimensions of FIG 4.18J Riser Pipe Holder — 65 )	-	850	NIL
2/2.3,(Refer fig 4.19 of Part4)(Dimensions of FIGFIG. 4.19 CONE PLATE)	-	850	NIL
2/2.3,(Refer fig 4.20 A of Part4)(Dimensions of FIG 4.20A Cone Flange)	-	850	NIL
2/2.3,(Refer fig 4.20 B of Part4)(Dimensions of FIG 4.20B Steel Cone)	-	850	NIL
2/2.3,(Refer fig 4.21 of Part4)(Dimensions of FIG. 4.21 CONNECTING ROD)	-	850	NIL
2/2.3,(Refer fig 4.22of Part4)(Dimensions of FIG. 4.22 PLUNGER ROD — STANDARD (For SDWP))	-	850	NIL
2/2.3,(Refer fig 4.23of Part4)(Dimensions of FIG.4.23 PLUNGERROD — LONG (For EDWP, VLOM-65 & VLOM-50 ))	-	850	NIL
2/2.3,(Refer fig 4.24of Part4)(Dimensions of FIG. 4.24 HANDLEAXE )	-	850	NIL
2/2.3,(Refer fig 4.25 of Part4)(Dimensions of FIG. 4.25 PUSHROD )	-	850	NIL
2/2.3,(Refer fig 4.26 of Part4)(Dimensions of FIG. 4.26 BEARINGSPACER)	-	850	NIL
2/2.3,(Refer fig 4.27 of Part4)(Dimensions of FIG.4.27 WASHER)	-	850	NIL
2/2.3,(Refer fig 4.28 of Part4)(Dimensions of FIG. 4.28 SOCKET— 32 (For SDWP & EDWP))	-	850	NIL
2/2.3,(Refer fig 4.29 of Part4)(Dimensions of FIG. 4.29 SOCKET— 50 (For VLOM-50))	-	850	NIL
2/2.3,(Refer fig 4.30 of Part4)(Dimensions ofFIG. 4.30 SOCKET— 65 (For VLOM-65))	-	850	NIL
2/2.3,(Refer fig 5.1 of Part 5)(Dimensions of FIG. 5.1 CYLINDER BODY— STANDARD (For SDWP))	-	850	NIL
2/2.3,(Refer fig 5.2 of Part 5)(Dimensions of FIG. 5.2 CYLINDERBODY— LONG (For EDWP & VLOM-65))	-	850	NIL
2/2.3,(Refer fig 5.3 of Part 5)(Dimensions of FIG. 5.3 CYLINDERBODY— VLOM-50)	-	850	NIL
2/2.3,(Refer fig 5.4 of Part 5)(Dimensions of FIG. 5.4 REDUCERCAP (For SDWP & EDWP) )	-	850	NIL
2/2.3,(Refer fig 5.5A of Part 5)(Dimensions of FIG. 5.5 A CYLINDERCAPS— VLOM-65 (For SDWP & EDWP))	-	850	NIL
2/2.3,(Refer fig 5.5B of Part 5)(Dimensions of FIG. 5.5 BCYLINDERCAPS— V LOM-65 (For SDWP & EDWP))	-	850	NIL
2/2.3,(Refer fig 5.6 of Part 5)(Dimensions ofFIG. 5.6 CYLINDERCAPS— VLOM-50)	-	850	NIL
2/2.3,(Refer fig 6.1 of Part 6)(Dimensions of FIG. 6.1 A BRASS LINER)	-	850	NIL
2/2.3,(Refer fig 6.2 of Part 6)(Dimensions of FIG. 6.2 PLUNGERYOKE BODY (For SDWP, EDWP & VLOM-65))	-	850	NIL
2/2.3,(Refer fig 6.3 of Part 6)(Dimensions of FIG. 6.3 UPPERVALVE (For SDWP, EDWP & VLOM-65))	-	850	NIL
2/2.3,(Refer fig 6.4 of Part 6)(Dimensions of FIG. 6.4 BUCKETSPACER— STANDARII (For SDWP, EDWP & VLOM-65))	-	850	NIL
2/2.3,(Refer fig 6.5 of Part 6)(Dimensions of FIG.6.5 BUCKET SPACER — LOWER (For EDWP))	-	600	NIL
2/2.3,(Refer fig 6.6 of Part 6)(Dimensions of FIG. 6.6 FOLLOWER — SDWP )	-	600	NIL
2/2.3,(Refer fig 6.7 of Part 6)(Dimensions of FIG. 6.7 FOLLOWER— EDWP)	-	600	NIL
2/2.3,(Refer fig 6.9 of Part 6)(Dimensions of FIG. 6.9 CHECK VALVE— STANDARD (For SDWP & EDWP) )	-	600	NIL
2/2.3,(Refer fig 6.10 of Part 6)(Dimensions of FIG. 6.10 CHECKVALVE— VLOM-65)	-	600	NIL
2/2.3,(Refer fig 6.11 of Part 6)(Dimensions of FIG. 6.11 RUBBERSEATRETAINER (For SDWP & EDWP))	-	600	NIL
2/2.3,(Refer fig 6.12 of Part 6)(Dimensions of FIG. 6.12 CHECK VALVE SEAT— STAN~AR~ (For SDWP & EDWP))	-	600	NIL
2/2.3,(Refer fig 6.13 of Part 6)(Dimensions of FIG. 6.13 CHECK VALVE — VLOM-65)	-	600	NIL
2/2.3,(Refer fig 6.14 of Part 6)(Dimensions of FIG. 6.14 CAGE (For VLOM-65))	-	600	NIL
2/2.3,(Refer fig 6.15 of Part 6)(Dimensions of FIG. 6.15 PLUNGERVALVE BODY— VLOM-50)	-	600	NIL
2/2.3,(Refer fig 6.16 of Part 6)(Dimensions of FIG. 6.16 CHECKVALVE BODY— VLOM-50)	-	600	NIL
2/2.3,(Refer fig 7.1 of Part 7)(Dimensions of FIG. 7.1 PUMPBUCKET— STANDARD (For SDWP, EDWP & VLOM-65) )	-	600	NIL
2/2.3,(Refer fig 7.2 of Part 7)(Dimensions of FIG. 7.2 PUMP BUCKET — VLOM-50)	-	600	NIL
2/2.3,(Refer fig 7.3 of Part 7)(Dimensions of FIG. 7.3 SEALINGRING— STANDARD (For SDWP & EDWP))	-	600	NIL
2/2.3,(Refer fig 7.4 of Part 7)(Dimensions of FIG. 7.4 SEALING RING— VLOM-65)	-	600	NIL
2/2.3,(Refer fig 7.5 of Part 7)(Dimensions of FIG. 7.5 SEALINGRING— VLOM-50)	-	600	NIL
2/2.3,(Refer fig 7.6 of Part 7)(Dimensions of FIG. 7.6 UPPERVALVE SEATING (For SDWP, EDWP & VLOM-65))	-	600	NIL
2/2.3,(Refer fig 7.7 of Part 7)(Dimensions of FIG. 7.7 LOWERVALVE SEATING— STANDARD (For SDWP & EDWP) )	-	600	NIL
2/2.3,(Refer fig 7.8 of Part 7)(Dimensions of FIG. 7.8 LOWERVALVE SEATING— VLOM-65 68)	-	600	NIL
2/2.3,(Refer fig 7.9 of Part 7)(Dimensions ofFIG. 7.9 BOBBIN (For VLOM-50))	-	600	NIL
2/2.3,(Refer fig 7.10 of Part 7)(Dimensions of FIG. 7.10 O-RING— VLOM-65)	-	600	NIL
2/2.3,(Refer fig 7.11 of Part 7)(Dimensions of FIG. 7.11 O-RING—VLOM-50)	-	600	NIL
2/2.3,(Refer fig 7.12 of Part 7)(Dimensions of FIG. 7.12 RUBBER CONE— VLOM-65 )	-	600	NIL
2/2.3,(Refer fig 7.13 of Part 7)(Dimensions of FIG. 7.13 RUBBERCONE— VLOM-50)	-	600	NIL
2/2.3,(Refer fig 7.14 of Part 7)(Dimensions of FIG. 7.14 PIPE CENTRALIZER— VLOM-65 )	-	600	NIL
2/2.3,(Refer fig 7.15 of Part 7)(Dimensions of FIG.7.15 PIPECENTRALIZER— VLOM-50 )	-	600	NIL
3/3.3.1,(Refer Cl 9.4.1 and 9.4.3 15500(Part 1 )(Head and Cylinder Assemblies)	-	600	NIL
6.2 of Part 1 ,Refer IS 4759(Galvanizing)	-	600	NIL
6.2.1 of Part 1,Refer Cl 5.9 of IS 2629(Galvanizing)	-	600	NIL
9.2 of Part1, (Visual Tests)	-	600	NIL
2/2.3 ,Refer Fig 3.1(Dimensions of FIG.4.1 HEAD— STANDARD(For SDWP, VLOM-65 and VLOM-50))	-	600	NIL
2/2.3 ,Refer Fig 3.1(Dimensions of FIG. 4.4 FRONT COVER)	-	600	NIL
2/2.3 ,Refer Fig 3.1(Dimensions of FIG. 4.24 HANDLE AXE )	-	600	NIL
2/2.3 ,Refer Fig 3.1(Dimensions of FIG.4.27 WASHER)	-	600	NIL
2/2.3 ,Refer Fig 3.1 and Refer annex B( HexagonaI Nut — )	-	600	NIL
2/2.3 ,Refer Fig 3.3 and annex B(Hexagonal Bolt)	-	600	NIL
2/2.3 ,Refer Fig 3.1 and 3.2(Dimensions of FIG.4.6 HANDLE— STANDARD (For SDWP, VLOM-65 & VLOM-50))	-	600	NIL
2/2.3 ,Refer Fig 3.1 and 3.2(Dimensions of FIG. 4.9 CHAIN WITH COUPLING)	-	600	NIL
2/2.3 ,Refer Fig 3.1 and 3.2(Dimensions of FIG. 4.26 BEARING SPACER)	-	600	NIL
2/2.3 ,Refer Fig 3.1 and 3.2,Annex B(Prevailing Torque Type Hex. Nut)	-	600	NIL
2/2.3 ,Refer Fig 3.3 and 3.4(Hex. Bolt —)	-	500	NIL
2/2.3 ,Refer Fig 3.3 and 3.4(Ball bearing, single side shielded)	-	500	NIL
2/2.3 ,Refer Fig 3.5(Dimensions of FIG. 4.22 PLUNGER ROD — STANDARD (For SDWP))	-	500	NIL
2/2.3 ,Refer Fig 3.5(Dimensions of FIG. 5.1 CYLINDER BODY— STANDARD (For SDWP))	-	500	NIL
2/2.3 ,Refer Fig 3.5(Dimensions of FIG. 5.4 REDUCERCAP (For SDWP & EDWP) )	-	500	NIL
2/2.3 ,Refer Fig 3.5(Dimensions of FIG. 6.1 BRASS LINER)	-	500	NIL
2/2.3 ,Refer Fig 3.5(Dimensions of FIG. 7.3 SEALINGRING— STANDARD (For SDWP & EDWP))	-	500	NIL
2/2.3 ,Refer Fig 3.5 and 3.6(Dimensions of FIG. 6.2 PLUNGERYOKE BODY (For SDWP, EDWP & VLOM-65))	-	500	NIL
2/2.3 ,Refer Fig 3.5 and 3.6(Dimensions of FIG. 6.3 UPPERVALVE (For SDWP, EDWP & VLOM-65))	-	500	NIL
2/2.3 ,Refer Fig 3.5 and 3.6(Dimensions of FIG. 6.4 BUCKETSPACER— STANDARII (For SDWP, EDWP & VLOM-65))	-	500	NIL
2/2.3 ,Refer Fig 3.5 and 3.6(Dimensions of FIG. 6.6 FOLLOWER — SDWP )	-	500	NIL
2/2.3 ,Refer Fig 3.5 and 3.6(Dimensions of FIG. 6.9 CHECK VALVE— STANDARD (For SDWP & EDWP) )	-	500	NIL
2/2.3 ,Refer Fig 3.5 and 3.6(Dimensions of FIG. 6.11 RUBBERSEATRETAINER (For SDWP & EDWP))	-	500	NIL
2/2.3 ,Refer Fig 3.5 and 3.6(Dimensions of FIG. 6.12 CHECK VALVE SEAT— STAN~AR~ (For SDWP & EDWP))	-	500	NIL
2/2.3 ,Refer Fig 3.5 and 3.6(Dimensions of FIG. 7.1 PUMPBUCKET— STANDARD (For SDWP, EDWP & VLOM-65) )	-	500	NIL
2/2.3 ,Refer Fig 3.5 and 3.6(Dimensions of FIG. 7.6 UPPERVALVE SEATING (For SDWP, EDWP & VLOM-65))	-	500	NIL
2/2.3 ,Refer Fig 3.5 and 3.6(Dimensions of FIG. 7.7 LOWERVALVE SEATING— STANDARD (For SDWP & EDWP) )	-	500	NIL
2/2.3 ,Refer Fig 3.7(Dimensions of FIG.4.23 PLUNGERROD — LONG (For EDWP, VLOM-65 & VLOM-50 ))	-	500	NIL
2/2.3 ,Refer Fig 3.7(Dimensions of FIG. 5.2 CYLINDERBODY— LONG (For EDWP & VLOM-65))	-	500	NIL
2/2.3 ,Refer Fig 3.7(Dimensions of FIG. 5.5 A Upper CAPS— VLOM-65 (For SDWP & EDWP))	-	500	NIL
2/2.3 ,Refer Fig 3.7(Dimensions of FIG. 5.5 B Bottomr CAPS— VLOM-65 (For SDWP & EDWP))	-	500	NIL
2/2.3 ,Refer Fig 3.7(Dimensions of FIG. 6.1 B BRASS LINER)	-	500	NIL
2/2.3 ,Refer Fig 3.7(Dimensions of FIG. 7.4 SEALING RING— VLOM-65)	-	500	NIL
2/2.3 ,Refer Fig 3.7 and 3.8(Dimensions of FIG. 6.2 PLUNGERYOKE BODY (For SDWP, EDWP & VLOM-65))	-	500	NIL
2/2.3 ,Refer Fig 3.9 and 3.10(Dimensions of FIG. 6.16 CHECKVALVE BODY— VLOM-50)	-	500	NIL
2/2.3 ,Refer Fig 3.9 and 3.10(Dimensions of FIG. 7.2 PUMP BUCKET — VLOM-50)	-	500	NIL
2/2.3 ,Refer Fig 3.7 and 3.8(Dimensions of FIG. 7.6 UPPERVALVE SEATING (For SDWP, EDWP & VLOM-65))	-	500	NIL
2/2.3 ,Refer Fig 3.7 and 3.8(Dimensions of FIG. 7.10 O-RING— VLOM-65)	-	500	NIL
2/2.3 ,Refer Fig 3.7 and 3.8(Check Nut)	-	500	NIL
2/2.3 ,Refer Fig 3.9(Dimensions of FIG.4.23 PLUNGERROD — LONG (For EDWP, VLOM-65 & VLOM-50 ))	-	500	NIL

19 Apr, 2028

-
-

IS 513 : Part 2 (2016)

Cold reduced carbon steel sheet and strip: Part 2 high tensile and multi - Phase steel (Sixth Revision)

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.0(CARBON)	-	500	-
6.0(MANGANESE)	-	500	-
6.0(SULPHUR)	-	500	-
6.0(PHOSPHORUS)	-	500	-
6.0(SILICON)	-	250	-
6.0(ALUMINIUM)	-	250	-
6.0(MICRO ALLOYS)	-	500	-
6.0(NITROGEN)	-	1500	-
Cl 7(UTM)	-	1500	-
Cl 8.5(Workmanship)	-	500	-
Cl 8.6(Workmanship)	-	500	-
Cl 9(Workmanship)	-	500	-
Cl 10(Length, Width & Thickness)	-	1000	-

19 Apr, 2028

-
-

IS 432 : Part 1 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 1 Mild Steel and Medium Tensile Steel Bars

Grade I, II/5-50/1mtr*3nos

3150 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause -4, 4.1( CARBON)	-	100	nil
Clause -4, 4.1(SULPHUR)	-	100	nil
Clause -4, 4.1(PHOSPHURS)	-	100	nil
Clause -4, 4.1(NITROGEN)	-	500	nil
Clause -4, 4.1( ALUMINIUM)	-	100	nil
Clause -4, 4.1(SILICON)	-	100	nil
Clause -4, 4.1(Nickel)	-	100	nil
Clause -4, 4.1(Chromium)	-	100	nil
Clause -4, 4.1(Molybdenum)	-	100	nil
Clause -4, 4.1(NIOBIUM)	-	150	nil
Clause -4, 4.2(VANADIUM)	-	100	nil
Clause -4, 4.3(TITANIUM)	-	100	nil
Cl 6.2(Diameter & Ovality)	-	150	nil
Cl 6.2(Weight)	-	150	nil
Cl 8(Physical Requirements)	-	500	nil
Cl 9.3(Press)	-	250	nil
Cl 5.1(Workmanship)	-	150	nil
Clause -4, 4.1(MANGANESE)	-	100	nil
Clause 4(Copper)	-	100	nil
Clause 4(Boron)	-	100	nil

19 Apr, 2028

-
-

IS 432 : Part 2 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 2 Hard-Drawn Steel Wire

Hard drawn steel wire

3500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 3.1.1(Sulphur)	-	500	-
Clause 3.1.1(Phosphorus)	-	500	-
Cl 4.1(Workmanship)	-	500	-
Cl 5 & 6(Diameter)	-	500	-
Cl 7(UTM)	-	1000	-
Cl 8.3(Bending To Both Side At 90°, Then Straight)	-	500	-

19 Apr, 2028

-
-

IS 12330 (1988)

Specificatioon for sulphate resisting Portland cement

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Fineness 4031 Part 2)	-	800	-
5.2.1(Expansion by Le Chatelier- 4031 Part 3)	-	500	-
5.2.1(Expansion by Autoclave- 4031 Part 3)	-	1000	-
5.3 a)(Setting Time Initial- 4031 Part 5)	-	250	-
5.3 b)(Setting Time Final- 4031 Part 5)	-	250	-
5.5 i)(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	700	-
5.5 ii)(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	700	-
5.5 iii)(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	700	-
4.1 - Table - 1 i(Ratio of percentage of lime to percentages of silica, alumina and iron oxide - Cl 4 of IS 4032:1985)	-	500	-
4.1 - Table - 1 ii(Insoluble residue - Cl 4.10 of IS 4032:1985)	-	500	-
4.1 - Table - 1 iii(Magnesia - Cl 4.8 of IS 4032:1985)	-	500	-
4.1 - Table - 1 iv(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-	500	-
4.1 - Table - 1 v(Tricalcium aluminate (C3A) - Cl 4 of IS 4032:1985)	-	500	-
4.1 - Table - 1 vi(Tetracalcium alumino ferrite phase plus twice the tricalcium aluminate ( C4AF + 2C3A ) - Cl 4 of IS 4032:1985)	-	500	-
4.1 - Table - 1 vii(Total loss on ignition - Cl 4.2 of IS 4032:1985)	-	500	-

19 Apr, 2028

-
-

IS 8041 (1990)

Rapid hardening portland cement - Specific4tion (Second Revision)

10500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Fineness 4031 Part 2)	-	800	-
6.2.1(Expansion by Le Chatelier- 4031 Part 3)	-	500	-
6.2.1(Expansion by Autoclave- 4031 Part 3)	-	1000	-
6.3 a)(Setting Time Initial- 4031 Part 5)	-	250	-
6.3 b)(Setting Time Final- 4031 Part 5)	-	250	-
6.4 a)(Compressive Strength At 24 hrs ± 30 minutes - IS 4031 Part 6)	-	700	-
6.4 b)(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	700	-
6.5(Transverse Strength - IS 4031 Part 8 (Optional))	-	2000	-

19 Apr, 2028

-
-

IS 1875 (1992)

Carbon steel billets, blooms, slabs and bars for forgings - Specification (Fifth Revision)

1/1A/2/2A/3/3A/4/5/6

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1, 6.2(carbon)	-	250	-
6.1, 6.2(sulphur)	-	250	-
6.1, 6.2(manganese)	-	250	-
6.1, 6.2(silicon )	-	250	-
6.1, 6.2(aluminium)	-	250	-
6.1, 6.2(nickel)	-	250	-
6.1, 6.2(cromium)	-	250	-
6.1, 6.2(copper)	-	250	-
6.1, 6.2(molybdenum)	-	250	-
6.1, 6.2(vanadium)	-	250	-
6.1, 6.2(boron)	-	250	-
6.1, 6.2(tin)	-	250	-
Cl 7(Workmanship)	-	500	-
Cl 8(Diameter, Ovality & Weight)	-	500	-
Cl 9(UTM & HBW)	-	500	-
Cl 12(Supplementary Requirements)	-	500	-
6.1, 6.2(phosphorus)	-	500	-

19 Apr, 2028

-
-

IS 7283 (1992)

Hot - Rolled bars for the production of bright bars and machined parts for engineering applications specification (First Revision)

HOT ROLLED BARS FOR THE PRODUCTION OF BRIGHT BARS

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 6(Workmanship)	-	500	-
Cl 7(Diameter & Out Of Round)	-	1000	-
Cl 8(Decarburization)	-	2500	-
Cl 9(Inclusion)	-	2000	-
Cl 10(Hardenability)	-	3000	-
Cl 11(Size)	-	1000	-
5, 5.1, 5.2(Chemical Composition - Carbon)	-	500	-
5, 5.1, 5.2(Chemical Composition - Sulphur)	-	500	-
5, 5.1, 5.2(Chemical Composition - Phosphorus)	-	500	-
5, 5.1, 5.2(Chemical Composition - Manganese)	-	500	-
5, 5.1, 5.2(Chemical Composition - Silicon)	-	500	-
5, 5.1, 5.2(Chemical Composition - Nickel)	-	500	-
5, 5.1, 5.2(Copper)	-	500	-
5, 5.1, 5.2(Chromium)	-	500	-
5, 5.1, 5.2(Chemical Composition - Lead)	-	500	-
5, 5.1, 5.2(Chemical Composition - Nitrogen)	-	1500	-

19 Apr, 2028

-
-

IS 7887 (1992)

Mild steel wire rod for general engineering purposes - Specification (First Revision)

1/2/3/4/4M/5/6/6M/7/8/8M

3500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Carbon %)	-	350	-
6.1(Sulphur %)	-	350	-
6.1(Phosphorus %)	-	250	-
6.1(Manganese %)	-	350	-
6.1( Aluminium %)	-	350	-
6.1(Silicon %)	-	350	-
Cl 8(Workmanship)	-	500	-
Cl 9(Nominal Diameter & Out Of Shape)	-	1000	-

19 Apr, 2028

-
-

IS 2879 (1998)

Mild steel for metal arc welding electrodes - Specification (Third Revision)

MILD STEEL FOR METAL ARC WELDING ELECTRODES

3500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Carbon %)	-	250	-
6(Sulphur %)	-	250	-
6(Phosphorus %)	-	250	-
6(Manganese %)	-	250	-
6(Silicon %)	-	250	-
6( Copper %)	-	250	-
6( Aluminium %)	-	250	-
6( Ti)	-	500	-
6(V)	-	250	-
6(Cr+ Mo+ Ni)	-	0	-
6(Mo)	-	250	-
6(Ni)	-	250	-
Cl 7(Workmanship)	-	250	-
Cl 8 & 9(Diameter)	-	250	-

19 Apr, 2028

-
-

IS 14650 (1999)

Carbon steel cast billet ingots, billets, blooms and slabs for re-rolling purposes - Specificaation

Carbon Steel Cast Billet

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Carbon- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	200	-
6(Manganese- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	200	-
6(Silicon- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	200	-
6(Nitrogen- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
6(Aluminium- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	200	-
6(Titanium- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
6(Vanadium- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	200	-
6(Nickel- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	200	-
6(Chromium- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	200	-
6(Copper- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	200	-
6(Molybdenum- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	200	-
6(Niobium- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	200	-
9 & 10(Dimensions and Tolerances )	-	500	-
11(Freedom from Defects )	-	500	-
12(Macro-examination )	-	1500	-
12(Sulphur Print Tests )	-	1500	-

19 Apr, 2028

-
-

IS 1239 : Part 1 (2004)

Steel Tubes, Tubulars and Other Wrought Steel Fittings : Part 1 Steel Tubes (BI-LINGUAL)

STEEL TUBES, TUBULARS AND OTHER WROUGHT STEEL FITTINGS

6500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause - 6.1.1, Table-1( CARBON)	-	300	-
Clause - 6.1.1, Table-1(SULPHUR)	-	300	-
Clause - 6.1.1, Table-1(PHOSPHURS)	-	200	-
Clause - 6.1.1, Table-1(MANGANESE)	-	200	-
6.2 AND AS PER IS 10748(SILICON)	-	200	-
6.2 AND AS PER IS 10748(ALUMINIUM)	-	200	-
6.2 AND AS PER IS 10748(MICRO ALLOY)	-	200	-
6.2 AND AS PER IS 10748(NITROGEN)	-	1000	-
6.2 AND AS PER IS 10748(COPPER)	-	200	-
12 AND AS PER IS 4736(MASS OF ZINC COATING)	-	800	-
12 AND AS PER IS 4736(UNIFORMITY OF ZINC COATING)	-	500	-
Cl 8(Outer Diameter, Thickness & Mass)	-	100	-
Clause 8.1 (Table3,4,5)(Nominal Bore )	-	100	-
Cl. 6.5(Height of Internal Fin)	-	100	-
Cl 14(Tensile Test, Flattening Test & Bend Test)	-	500	-
Clause 14.1.1(Elongation Percent)	-	200	-
Clause 11.2(Exact Length)	-	100	-
Cl. 8, 9 Table 3,4 & 5(Mass of Tube)	-	200	-
Cl 15(Workmanship)	-	100	-
Cl. 14.2(Bend Test (uto and including 50 mm NB))	-	500	-
Cl. 14.3(Flattening test (Over 50 mm NB))	-	500	-

19 Apr, 2028

-
Plain ended pipe only.

IS 10748 (2004)

Hot - Rolled steel strip for welded tubes and pipes - Specification (Second Revision)

1/2/3/4/6

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Table 1 ( Clauses 7.1 ,7.2 )( CARBON)	-	200	-
Table 1 ( Clauses 7.1 ,7.2 )(SULPHUR)	-	200	-
Table 1 ( Clauses 7.1 ,7.2 )(PHOSPHURS)	-	200	-
Table 1 ( Clauses 7.1 ,7.2 )(MANGANESE)	-	300	-
Table 1 ( Clauses 7.1 ,7.2 )(NITROGEN)	-	1000	-
Table 1 ( Clauses 7.1 ,7.2 )(SILICON)	-	300	-
Table 1 ( Clauses 7.1 ,7.2 )( ALUMINIUM)	-	300	-
Table 1 ( Clauses 7.1 ,7.2 )(Nickel)	-	300	-
Table 1 ( Clauses 7.1 ,7.2 )(Chromium)	-	200	-
Table 1 ( Clauses 7.1 ,7.2 )(Molybdenum)	-	200	-
Table 1 ( Clauses 7.1 ,7.2 )(NIOBIUM)	-	300	-
Table 1 ( Clauses 7.1 ,7.2 )(VANADIUM)	-	200	-
Table 1 ( Clauses 7.1 ,7.2 )(TITANIUM)	-	200	-
Table 1 ( Clauses 7.1 ,7.2 )(CARBON EQUIVELENT )	-	0	-
Cl 8 & Table 3(UTM)	-	500	-
Cl 9(Press)	-	500	-
Cl 11(Workmanship)	-	100	-

19 Apr, 2028

-
-

IS 3601 (2006)

Steel tubes for mechanical and general engineering purposes - Specification (Second Revision)

STEEL TUBES FOR MECHANICAL AND GENERAL ENGINEE~G PURPOS

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Material)	-	300	-
4.1(Sulphur-Percentage by mass)	-	250	-
4.1(Phosphorus-Percentage by mass)	-	250	-
6.0(Workmanship)	-	500	-
8.0(Straightness)	-	500	-
11.1(Surface Protection)	-	1000	-
11.2(Surface Protection)	-	1000	-
13.1.3(Tensile Strength)	-	250	-
13.1.1(Yield Stress)	-	250	-
13.1.2(Elongation)	-	250	-
13.2(Flattening Test)	-	1000	-
13.3(Bend Test (Strip))	-	250	-
13.4(Bend Test (Whole Tube))	-	500	-
13.5(Drift Expansion Test)	-	500	-
13.6(Crush Test)	-	100	-
19.1.3(Height of Internal Fin)	-	100	-

19 Apr, 2028

-
-

IS 15647 (2006)

Hot rolled steel narrow width strip for welded tubes and pipes

HOT ROLLED STEEL NARROW WIDTH STRIP

5000 View breakup
-

Clause No.	Exclusion	Remark
Cl 8(UTM)	-	-
Cl 9(Press)	-	-
Cl 11(Workmanship)	-	-
Cl 12(Length, Width & Thickness)	-	-
Cl 13(Workmanship)	-	-

19 Apr, 2028

-
-

IS 1786 (2008)

High strength deformed steel bars and wires for concretere inforcement - Specification (Fourth Revision)

HIGH STRENGTH DEFORMED STEEL BARS

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Carbon %)	-	500	-
4.1(Sulphur %)	-	500	-
4.1(Phosphorus %)	-	500	-
4.1(Silicon %)	-	0	-
4.1( Copper %)	-	0	-
4.1( Aluminium %)	-	0	-
4.1( Nb)	-	0	-
4.1(V)	-	0	-
4.1( Ti)	-	0	-
4.1(Cr)	-	0	-
4.1(Mo)	-	0	-
4.1( Nitrogen%)	-	1500	-
4.1(CE)	-	1000	-
Cl. 5 (Cl. 5 - Mean projected area of transverse ribs (1/3 of Ar))	-	1000	-
Cl. 5 (Cl.5 Mean area of ribs/unit length (Ar), )	-	1000	-
Cl. 6.1(Nominal Size)	-	500	-
Cl. 7.2 Table -2 (Nominal Mass)	-	500	-
Cl. 8.1 Table 3(TS/YS ratio)	-	500	-
Cl. 8.1 Table 3(Tensile Strength (TS))	-	1000	-
Cl. 8.1 Table 3(Yield Stress (YS))	-	1000	-
Cl. 8.1 Table 3(Elongation, percentage)	-	1000	-
Cl 9.3(Load In One Direction)	-	1500	-
Cl 9.4(Load In Other Direction From Bend)	-	1500	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 SULPHUR+PHOSPHUR)	-	500	-

19 Apr, 2028

-
-

IS 6240 (2008)

Hot rolled steel plate (Up To 6 Mm) sheet and strip for the manufacture of low pressure liquefiable gas cylinders (Fourth Revision)

8500 View breakup
-

Clause No.	Exclusion	Remark
6.1(Carbon %)	-	-
6.1(Sulphur %)	-	-
6.1(Phosphorus %)	-	-
6.1(Manganese %)	-	-
6.1(Silicon %)	-	-
6.1(Nitrogen%)	-	-
6.1( Aluminium %)	-	-
Cl 7(UTM)	-	-
Cl 8(Press)	-	-
Cl 10(Erichsen Cupping)	-	-
Cl 13(Length, Width & Thickness)	-	-

19 Apr, 2028

-
-

IS 3502 (2009)

Steel chequered plates (Third Revision)

Chequered Plates

6500 View breakup
-

Clause No.	Exclusion	Remark
Cl 5(Workmanship)	-	-
Cl 8(Tensile Test)	-	-
Cl 10(Length, Width, Thickness & Chequered Height)	-	-

19 Apr, 2028

-
-

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

HOT ROLLED STEEL

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause - 5, 8.1 & 8.2(E250, CARBON)	-	250	Nil
Clause - 5, 8.1 & 8.2(E250, SULPHUR)	-	250	Nil
Clause - 5, 8.1 & 8.2(E250, PHOSPHURS)	-	250	Nil
Clause - 5, 8.1 & 8.2(E250 ,MANGANESE)	-	250	Nil
Clause - 5, 8.1 & 8.2(E250, NITROGEN)	-	1000	Nil
Clause - 5, 8.1 & 8.2(E250, SILICON)	-	250	Nil
Clause - 5, 8.1 & 8.2(E250, ALUMINIUM)	-	250	Nil
Clause - 5, 8.1 & 8.2(E250, CARBON +EQUIVELENT )	-	250	Nil
Cl 7(Workmanship)	-	500	Nil
Cl 10.3(UTM)	-	1000	Nil
Cl 11.3(Press)	-	500	Nil
Cl 12(Sudden Load Applied)	-	1150	Nil
Cl 13(Y Groove Cracking Test)	-	0	NA
Cl 18(Weight)	-	100	Nil
Clause - 5, 8.1 & 8.2(E275, CARBON)	-	250	Nil

19 Apr, 2028

-
Except- Y Groove Crackability test (Cl.13) & Other tests (Cl.14)

1
2
3
Next
Last

Bureau of Indian Standards

The National Standards Body of India

LUCID LABORATORIES PRIVATE LIMITED, HYDERABAD

PLOT NO.3, IDA,, BALANAGAR, HYDERABAD, Medchal Malkajgiri, Telangana, 500037

9848163346 info@lucidlabsindia.com

Scope List