BIS - LIMS (Laboratory Information Management System)

LUCID LABORATORIES PRIVATE LIMITED, HYDERABAD

PLOT NO.3, IDA,, BALANAGAR, HYDERABAD, Medchal Malkajgiri, Telangana, 500037

9848163346 info@lucidlabsindia.com

Scope List

Reset

65 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 733 (1983)

Specification for wrought aluminium and aluminium alloy bars, rods and sections (For General Engineering Purposes) (Third Revision)

10500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 4(Freedom from Defects)	-	300	-
Cl. 5.1, Table 2(0.2 Percent proof stress- IS 1816)	-	1200	-
Cl. 5.1, Table 2(Tensile Strength- IS 1816)	-	1200	-
Cl. 5.1, Table 2(Elongation on 50 mm or 5.65√So Gauge Length)	-	1200	-
Cl. 0.4, 5.1, Table 1(Aluminium- IS 504 or by any other suitable instrumental method)	-	400	-
Cl. 0.4, 5.1, Table 1(Copper- IS 504 or by any other suitable instrumental method)	-	500	-
Cl. 0.4, 5.1, Table 1(Magnesium- IS 504 or by any other suitable instrumental method)	-	500	-
Cl. 0.4, 5.1, Table 1(Silicon- IS 504 or by any other suitable instrumental method)	-	500	-
Cl. 0.4, 5.1, Table 1(Iron- IS 504 or by any other suitable instrumental method)	-	500	-
Cl. 0.4, 5.1, Table 1(Zinc- IS 504 or by any other suitable instrumental method)	-	500	-
Cl. 0.4, 5.1, Table 1(Aluminium- IS 504 or by any other suitable instrumental method)	-	0	-
Cl. 0.4, 5.1, Table 1(Titanium and / or other grain refining elements - IS 504 or by any other suitable instrumental method)	-	500	-
Cl. 0.4, 5.1, Table 1(Chromium- IS 504 or by any other suitable instrumental method)	-	500	-
Cl. 0.4, 5.1, Table 1(Ti+ V- IS 504 or by any other suitable instrumental method)	-	500	-
Cl. 0.4, 5.1, Table 1(Total Impurities- IS 504 or by any other suitable instrumental method)	-	200	-
Cl. 0.4, 5.1, Table 1(Cr+ Mn- IS 504 or by any other suitable instrumental method)	-	500	-
7(Dimension - IS 3965)	-	800	-
11(Marking)	-	200	-
Table-1, Clause - 5.1(Manganese)	-	500	-
Table-1, Clause - 5.1(Copper)	-	0	-
Table-1, Clause - 5.1(Iron)	-	0	-
Table-1, Clause - 5.1(Magnesium)	-	0	-
Table-1, Clause - 5.1(Titanium)	-	0	-
Table-1, Clause - 5.1(Silicon)	-	0	-
Table-1, Clause - 5.1(Chromium)	-	0	-
Table-1, Clause - 5.1(Zinc)	-	0	-

19 Apr, 2028

-
-

IS 5522 (2014)

Stainless steel sheets and strips for utensils - Specification (Third Revision)

9600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 7.1 & 7.2 Table 1(Carbon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	-
Cl. 7.1 & 7.2 Table 1(Silicon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	-
Cl. 7.1 & 7.2 Table 1(Manganese -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	-
Cl. 7.1 & 7.2 Table 1(Nickel -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	-
Cl. 7.1 & 7.2 Table 1(Chromium -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	-
Cl. 7.1 & 7.2 Table 1(Sulphur -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	-
Cl. 7.1 & 7.2 Table 1(Phosphorus -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	-
Cl. 7.1 & 7.2 Table 1(Nitrogen -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	-
8.2, Table 3(Tensile Test-1608:Part 1)	-	0	-
8.2, Table 3(Proof Stress, N/mm2)	-	1000	-
8.2, Table 3(Tensile Strength, N/mm2)	-	1000	-
8.2, Table 3(Elongation, %)	-	1000	-
8.3(Hardness , max-IS 1500 or IS 1501 (Part 1) or IS 1586)	-	1000	-
8.4(Bend Test)	-	500	-
8.5(Erichsen Cupping Test)	-	500	-
10.1(Thickness, mm)	-	100	-
10.2(width, mm)	-	100	-
10.3(Length, mm)	-	100	-
10.4(Flatness,mm)	-	100	-
10.5(Camber, mm)	-	100	-
11(Surface Finish)	-	100	-
Cl . 6 .0(Freedom from defect)	-	100	-
13(Marking)	-	100	-

19 Apr, 2028

-
-

IS 737 (2008)

Wrought aluminium and aluminium alloy sheet and strip for general engineering purposes - Specification (Fourth Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.0(Freedom from defects)	-	300	-
6 Table-1(Al)	-	500	-
6 Table-1(Cu)	-	500	-
6 Table-1(Mg)	-	500	-
6 Table-1(Si)	-	500	-
6 Table-1(Fe)	-	500	-
6 Table-1(Mn)	-	500	-
6 Table-1(Zn)	-	500	-
6 Table-1(Ti)	-	500	-
6 Table-1(Cr)	-	500	-
6 Table-1(Cu+Si+Fe)	-	100	-
6 Table-1(Cu+Si+Fe+Mn+Zn)	-	100	-
6 Table-1(Cu+Mg+Si+Fe+Mn+Zn)	-	100	-
6 Table-1(Zr)	-	500	-
6 Table-1(Cr+Mn)	-	100	-
7 Table-2(Tensile Strength)	-	1500	-
7 Table-2(Elongation)	-	1500	-
7 Table-2(0.2 % Proof Stress)	-	1500	-
7 Table-2(Bend Test)	-	1000	-
9(Dimension - IS 2676)	-	700	-
12(Marking)	-	100	-

19 Apr, 2028

-
-

IS 736 (1986)

Specification for wrought aluminium and aluminium alloy plate for general engineering purposes (Third Revision)

10500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Freedom from defect)	-	300	-
5(chemical composition)	-	0	-
6.1 table 2(0.2% proof strength)	-	1500	-
6.1 table 2(tensile strength)	-	1500	-
6.1 table 2(Elongation)	-	1500	-
8(Dimensions & Tolerances)	-	700	-
5.1, Table 1(Copper)	-	500	-
5.1, Table 1(Magnesium)	-	500	-
5.1, Table 1(Silicon)	-	500	-
5.1, Table 1(Iron)	-	500	-
5.1, Table 1(Mangnese)	-	500	-
5.1, Table 1(Zinc)	-	500	-
5.1, Table 1(Chromium)	-	500	-
5.1, Table 1(Titanium and /or other grain refining element)	-	500	-
5.1, Table 1(Aluminium)	-	500	-
5.1, Table 1(Vanadium)	-	500	-
4(Freedom from defect)	-	0	-
5(chemical composition)	-	0	-
6.1 table 2(0.2% proof strength)	-	0	-
6.1 table 2(tensile strength)	-	0	-
6.1 table 2(Elongation)	-	0	-
8(Dimensions & Tolerances)	-	0	-
5.1, Table 1(Copper)	-	0	-
5.1, Table 1(Magnesium)	-	0	-
5.1, Table 1(Silicon)	-	0	-
5.1, Table 1(Iron)	-	0	-
5.1, Table 1(Mangnese)	-	0	-
5.1, Table 1(Zinc)	-	0	-
5.1, Table 1(Chromium)	-	0	-
5.1, Table 1(Titanium and /or other grain refining element)	-	0	-
5.1, Table 1(Aluminium)	-	0	-
5.1, Table 1(Vanadium)	-	0	-

19 Apr, 2028

-
-

IS 14650 (2023)

UNALLOYED AND ALLOYED STEEL INGOT AND SEMI-FINISHED PRODUCTS FOR RE-ROLLING PURPOSES - SPECIFICATION (First Revision)

8400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause - 7.1(CARBON)	-	200	-
Clause - 7.1(SULPHUR)	-	200	-
Clause - 7.1(PHOSPHURS)	-	200	-
Clause - 7.1(MANGANESE)	-	200	-
Clause - 7.1(NITROGEN)	-	400	-
As per Clause 10(Dimension)	-	0	-
As per Clause 10.1(Dimension Width)	-	60	-
As per Clause 10.1(Dimension Thickness)	-	60	-
As per Clause 10.2(Dimension Length)	-	60	-
As per Clause 11.5(Bend)	-	100	-
As per Clause 11.6(Camber)	-	100	-
As per Clause 11.7 (i)(Out of Square)	-	60	-
As per Clause 11.7 (ii)(Round Corners)	-	60	-
As per Clause 12/12.1/12.2/12.3(Freedom from defects)	-	100	-
Clause. 13(Macro examination test.)	-	1500	-
Clause. 13(Sulphur print.)	-	1500	-
Clause. 13(Inclusion content)	-	1000	-
Clause.7.1(Silicon)	-	200	-
Clause.7.1(Carbon Equbalant)	-	1000	-
Clause.7.1(Microalloy element)	-	800	-
As per Clause 11/11.1/11.2/11.3/11.4(Tolerances)	-	50	-
As per Clause 11.7 (iii)(Ridges due to gas cutting)	-	50	-
As per Clause 11.7 (iv)(Taper (Width variation on top and bottom surface at one location)	-	50	-
As per Clause 11.7 (v)(Edge slanting (Width variation on top and bottom surface at one location)	-	50	-
As per Clause 11.7 (vi)(Convexity(Difference in thickness from edge to curve)	-	50	-
As per Clause 11.7 (vii)(Chamfering (Length variation on top and bottom surface at one location)	-	50	-
As per Clause 11.7 (viii)(Wedge (Thickness variation at the edges along the cross section)	-	50	-
As per Clause 11.7 (ix)(Scarfing pits)	-	50	-
Clause. 13(Macro examination test.)	-	50	-
Clause. 14(Marking)	-	50	-
Clause.15(Ordering information)	-	50	-
Clause.6.0(Manufacture)	-	50	-

19 Apr, 2028

-
-

Bureau of Indian Standards

The National Standards Body of India

LUCID LABORATORIES PRIVATE LIMITED, HYDERABAD

PLOT NO.3, IDA,, BALANAGAR, HYDERABAD, Medchal Malkajgiri, Telangana, 500037

9848163346 info@lucidlabsindia.com

Scope List