BIS - LIMS (Laboratory Information Management System)

Atmy Analytical Labs Pvt. Ltd.

I-30,DLF Industrial Area, Phase-1, Faridabad, Faridabad, Haryana, 121003

9910808996 info@atmylabs.com

Scope List

Reset

288 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

121

IS 14885 (2022)

Polyethylene Pipes for the Supply of Gaseous Fuels ï¿½ Specification (First Revision)

All

309000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2(Grade of material)	-	103000	Rs.103000 without Long duration (10000Hrs) hydro static testing
4.3(Nominal Diameter)	-	103000	Rs.103000 without Long duration (10000Hrs) hydro static testing
4.4(Colour)	-	103000	Rs.103000 without Long duration (10000Hrs) hydro static testing
5.1(Polyethylene compound)	-	103000	Additional charges for Raw materials is Rs. 35000/- Rs.103000 without Long duration (10000Hrs) hydro static testing
5.3(Anti-oxidant)	-	103000	Additional charges for Raw materials is Rs. 35000/- Rs.103000 without Long duration (10000Hrs) hydro static testing
5.4(U-V stabilizer)	-	103000	Additional charges for Raw materials is Rs. 35000/- Rs.103000 without Long duration (10000Hrs) hydro static testing
5.7(PE Compound Quality Evaluation)	-	206000	Rs. 2,06,000 for PE evaluation test with long duration (10000Hrs) Hydrostatic test charges only.
5.5(Effect of Gas condensate on the Hydrostatic strength)	-	103000	Additional charges for Raw materials is Rs. 35000/- Rs.103000 without Long duration (10000Hrs) hydro static testing
5.6(Resistance to Weathering)	-	103000	Additional charges for Raw materials is Rs. 35000/- Rs.103000 without Long duration (10000Hrs) hydro static testing
6.1(Outside Diameter)	-	103000	Additional charges for Raw materials is Rs. 35000/- Rs.103000 without Long duration (10000Hrs) hydro static testing
6.1(Out of Roundness (Ovality))	-	103000	Additional charges for Raw materials is Rs. 35000/- Rs.103000 without Long duration (10000Hrs) hydro static testing
6.2(Wall Thickness)	-	103000	Additional charges for Raw materials is Rs. 35000/- Rs.103000 without Long duration (10000Hrs) hydro static testing
7(Finish)	-	103000	Additional charges for Raw materials is Rs. 35000/- Rs.103000 without Long duration (10000Hrs) hydro static testing
8.1(Internal pressure creep rupture test for plain at 80 deg. C for 165h)	-	103000	Additional charges for Raw materials is Rs. 35000/- Rs.103000 without Long duration (10000Hrs) hydro static testing
8.1(Internal pressure creep rupture test for plain pipes at 20 deg. C for 100h)	-	103000	Additional charges for Raw materials is Rs. 35000/- Rs.103000 without Long duration (10000Hrs) hydro static testing
8.1(Internal pressure creep rupture test for plain pipes at 80 deg. C for 1000 h)	-	103000	Additional charges for Raw materials is Rs. 35000/- Rs.103000 without Long duration (10000Hrs) hydro static testing
8.2(Reversion Test)	-	103000	Additional charges for Raw materials is Rs. 35000/- Rs.103000 without Long duration (10000Hrs) hydro static testing
8.3(Density)	-	103000	Additional charges for Raw materials is Rs. 35000/- Rs.103000 without Long duration (10000Hrs) hydro static testing
8.6(Thermal Stability (Oxidation Induction Time))	-	103000	Additional charges for Raw materials is Rs. 35000/- Rs.103000 without Long duration (10000Hrs) hydro static testing
8.7(Volatile Matter Content)	-	103000	Additional charges for Raw materials is Rs. 35000/- Rs.103000 without Long duration (10000Hrs) hydro static testing
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	103000	Additional charges for Raw materials is Rs. 35000/- Rs.103000 without Long duration (10000Hrs) hydro static testing
8.9(Resistance to Weathering)	-	103000	Additional charges for Raw materials is Rs. 35000/- Rs.103000 without Long duration (10000Hrs) hydro static testing
6.4(Length of Pipe)	-	103000	Additional charges for Raw materials is Rs. 35000/- Rs.103000 without Long duration (10000Hrs) hydro static testing
8.4(Melt Flow Rate (MFR))	-	103000	Additional charges for Raw materials is Rs. 35000/- Rs.103000 without Long duration (10000Hrs) hydro static testing
8.5(Pigment Dispersion)	-	103000	Additional charges for Raw materials is Rs. 35000/- Rs.103000 without Long duration (10000Hrs) hydro static testing
8.10(Slow Crack Growth Rate Test)	-	103000	Additional charges for Raw materials is Rs. 35000/- Rs.103000 without Long duration (10000Hrs) hydro static testing
8.11(Squeeze-off)	-	103000	Additional charges for Raw materials is Rs. 35000/- Rs.103000 without Long duration (10000Hrs) hydro static testing
5.1, 5.7 Table 2(i) Conventional density (of base polymer))	-	103000	Additional charges for Raw materials is Rs. 35000/- Rs.103000 without Long duration (10000Hrs) hydro static testing
5.1, 5.7 Table 2(ii) Melt flow rate (MFR))	-	103000	Additional charges for Raw materials is Rs. 35000/- Rs.103000 without Long duration (10000Hrs) hydro static testing
5.1, 5.7 Table 2(iii) Thermal stability (oxidation induction time))	-	103000	Additional charges for Raw materials is Rs. 35000/- Rs.103000 without Long duration (10000Hrs) hydro static testing
5.1, 5.7 Table 2(iv) Volatile content)	-	103000	Additional charges for Raw materials is Rs. 35000/- Rs.103000 without Long duration (10000Hrs) hydro static testing
5.1, 5.7 Table 2(v) Water content1))	-	103000	Additional charges for Raw materials is Rs. 35000/- Rs.103000 without Long duration (10000Hrs) hydro static testing
5.1, 5.7 Table 2(vi) Pigment dispersion)	-	103000	Additional charges for Raw materials is Rs. 35000/- Rs.103000 without Long duration (10000Hrs) hydro static testing
5.1, 5.7 Table 3(iv) Resistance to slow crack growth rate)	-	103000	Additional charges for Raw materials is Rs. 35000/- Rs.103000 without Long duration (10000Hrs) hydro static testing
5.6(ii) Hydraulic characteristics)	-	103000	Additional charges for Raw materials is Rs. 35000/- Rs.103000 without Long duration (10000Hrs) hydro static testing
5.6(iii) Thermal stability (Oxidation induction time))	-	103000	Additional charges for Raw materials is Rs. 35000/- Rs.103000 without Long duration (10000Hrs) hydro static testing
6(Dimensions of pipes)	-	103000	Additional charges for Raw materials is Rs. 35000/- Rs.103000 without Long duration (10000Hrs) hydro static testing
10(Marking)	-	103000	Additional charges for Raw materials is Rs. 35000/- Rs.103000 without Long duration (10000Hrs) hydro static testing

Complete

25 Feb, 2027

-
Revised version of IS 14885:2022 included w.e.f. 04.08.2023

122

IS 2052 (2023)

Compounded feeds for cattle ï¿½ Specification

all

14800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl no.4.1(General)	-	500	-
Cl no.4.2(Ingredients)	-	500	-
Cl no.4.3,7.1, Table no. 1(i)(Moisture)	-	1500	-
Cl no.4.3,7.1, Table no. 1(ii)(Crude protein (N × 6.25))	-	2000	-
Cl no.4.3, 7.1,Table no. 1(iii)(Crude fat)	-	2000	-
Cl no.4.3 ,7.1, Table no. 1(iv)(Crude fibre)	-	2000	-
Cl no.4.3 ,7.1, Table no. 1(v)(Acid insoluble ash)	-	1500	-
Cl no.4.3,7.1Table no. 1(vi)("Salt (as NaCl based on Na or Cl), percent by mass")	-	1500	-
Cl no.4.3 7.1,Table no. 1(vii)(Calcium (as Ca))	-	2500	-
Cl no.4.3,7.1,Table no. 1(viii)(Total phosphorus)	-	2000	Rs. 2000 for Cl no.4.3,7.1,Table no. 1(ix) (Available phosphorus)
Cl no.4.3 ,7.1, Table no. 1(x)(Urea, percent by mass)	-	2000	-
Cl no.4.3,7.1, Table no. 1(xi)(Vitamin A)	-	2500	-
Cl no.4.3,7.1,Table no. 1(xii)(Vitamin D)	-	2500	-
Cl no.4.3 ,7.1, Table no. 1(xiii)(Vitamin E)	-	2500	-
Cl no.4.3 ,7.1, Table no. 1(xiv)(Aflatoxin B1)	-	2500	-
Cl no.4.3 ,7.1, Table no. 1(xv)(Cadmium)	-	2500	-
Cl no.5(Packing and marking)	-	500	-

Complete

25 Feb, 2027

-
Revised version of IS 2052:2023 Included w.e.f. 20.07.2023.

123

IS 5557 (2004)

Industrial and protective rubber knee and ankle boots - Specification (Fourth Revision)

all

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5/5.1.7/5.1.7.8(REQUIREMENTS- Physical Requirements-Resistance to oil)	-	12000	-
5/5.1.1-Fig. 1, Fig. 2 and Fig. 3(REQUIREMENTS-Design)	-	12000	-
5/5.1.2 -IS 1638(REQUIREMENTS-Size)	-	12000	-
5/5.1.3-Table1(REQUIREMENTS-Thickness)	-	12000	-
5/5.1.4/5.1.4.1-Table2(REQUIREMENTS-Materials-Rubber components)	-	12000	-
5/5.1.4/5.1.4.2(REQUIREMENTS-Materials-Fabric- accordance with IS 1969)	-	12000	-
5/5.1.4/5.1.4.3(REQUIREMENTS-Materials-Protective Steel Toe Cap- an per IS 5852)	-	12000	-
5/5.1.6/5.1.6.1-Fig. 1, Fig. 2, Fig. 3, .Fig. 4, Fig. 5 and Table 3.(REQUIREMENTS- Construction)	-	12000	-
5/5.1.6/5.1.6.2(REQUIREMENTS- Construction)	-	12000	-
5/5.1.7/5.1.7.1(REQUIREMENTS- Physical Requirements-Heat treatment- as per IS 3400 (Part 4))	-	12000	-
5/5.1.7/5.1.7.2(REQUIREMENTS- Physical Requirements-Composite strength)	-	12000	-
5/5.1.7/5.1.7.3-Table 4(REQUIREMENTS- Physical Requirements-Flexing endurance- as per Annex B.)	-	12000	-
5/5.1.7/5.1.7.4(REQUIREMENTS- Physical Requirements- Leakage resistance test)	-	12000	-
5/5.1.7/5.1.7.5(REQUIREMENTS- Physical Requirements- Consolidation test- as per IS IS 3400 (Part 5))	-	12000	-
5/5.1.7/5.1.7.6(REQUIREMENTS- Physical Requirements- Performance test- as per Annex C)	-	12000	-
5/5.1.7/5.1.7.7(REQUIREMENTS- Physical Requirements-Height of the boots)	-	12000	-
5/5.1.7/5.1.7.8(REQUIREMENTS- Physical Requirements-Resistance to oil)	-	12000	-
5, 5.1(Requirement)	-	12000	-
6.1(Marking)	-	12000	-
6, 6.1(Packing)	-	12000	-

Complete

25 Feb, 2027

-
Included w.e.f. 17.07.2023

124

IS 5557 : Part 2 (2018)

All rubber gum boots and ankle boots: Part 2 occupational purposes

all

47200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(VISUAL)	-	47200	-
3.2(specificgravity)	-	47200	-
3.3(specificgravity)	-	47200	-
3.4(specificgravity)	-	47200	-
3.5(visual)	-	47200	-
3.6(VISUAL)	-	47200	-
3.7(VISUAL)	-	47200	-
4(visual)	-	47200	-
5(visual)	-	47200	-
6(visual)	-	47200	-
7.1(visual)	-	47200	-
7.1.1(Tear strength)	-	47200	-
7.1.2(Abrasion resistance)	-	47200	-
7.2(all test of table 1)	-	47200	-
7.3(all test of table 2)	-	47200	-
7.3(sulphur test)	-	47200	-
7.4(Visual)	-	47200	-
7.4.1(all test of table 3)	-	47200	-
7.5(Visual)	-	47200	-
7.5.1(Tensile)	-	47200	-
7.5.2(Thickness)	-	47200	-
7.5.3(Upper flexing)	-	47200	-
7.6(VISUAL)	-	47200	-
7.6.1(Out sole thickness)	-	47200	-
7.6.2(out sole tear strength)	-	47200	-
7.6.3(out sole abrasion)	-	47200	-
7.6.5(Interlayer bond strength)	-	47200	-
7.7(INSOCK Visual)	-	47200	-
7.7.1(Insock thickness)	-	47200	-
7.7.2(Insock abrasion)	-	47200	-
8(CONSTRUCTION)	-	47200	-
8.1(Hot contact)	-	47200	-
8.2(Leak proofness)	-	47200	-
8.3(Height of upper)	-	47200	-
8.4(Adhesion test)	-	47200	-
8.5(Resistance to acid & alkaline)	-	47200	-
8.6(Resistance to fule oil)	-	47200	-
8.7.1(Antistatic)	-	47200	-
8.7.2(CONDUCTIVE FOOTWEAR)	-	47200	-
8.7.3(Elecrically nsulating footwear)	-	47200	-
8.7.4(Resistance to cold)	-	47200	-
10(Visual OBSERVATION)	-	47200	-
11.1(Visual OBSERVATION)	-	47200	-
11.3(Visual OBSERVATION)	-	47200	-

Complete

25 Feb, 2027

-
Included w.e.f. 17.07.2023

125

IS 5676 (1995)

Moulded solid rubber soles and heels - SpecificatlOn (Second Revision)

all

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5/5.3/5.3.1(REQUIREMENTS- Construction)	-	7500	-
5/5.1(REQUIREMENTS-General)	-	7500	-
5/5.2- Fig. 1 to 5(REQUIREMENTS-Design)	-	7500	-
5/5.5- Table1(REQUIREMENTS-Thickness)	-	7500	-
5/5.6/5.6.1(REQUIREMENTS-Channel)	-	7500	-
5/5.7- Table2(REQUIREMENTS- Physical Requirements- as per IS 3400 (Part 1, Part 2, Part 4, Part 9, Part 10, Part 16))	-	7500	-
6(Marking and packing)	-	7500	-
8.1(Test methods)	-	7500	-
8.3(Measurement of thickness)	-	7500	-
Cl.6.1,6.2,6.3(Marking and packing)	-	7500	-

Complete

25 Feb, 2027

-
Included w.e.f. 17.07.2023

126

IS 17012 (2018)

High ankle tactical boots with pu - Rubber sole - Specification

all

52900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.16.2(Breaking Strength of lace )	-	52900	-
4.16.1(Length of lace )	-	52900	-
4.15(D-ring & Hooks )	-	52900	-
6.1(Resistance to Fuel Oil)	-	52900	-
4.14.9(Resistance to hot contact )	-	52900	-
4.14.8(Flexing resistance )	-	52900	-
4.14.7(Ageing test)	-	52900	-
4.14.6(Hardness (IRHD))	-	52900	-
4.14.5(Abrasion resistance )	-	52900	-
4.14.4(Tear Strength)	-	52900	-
4.14.3(Sole Density )	-	52900	-
4.14.2(Thickness)	-	52900	-
4.14.1(Meterial)	-	52900	-
4.13(Breaking Strength of thread )	-	52900	-
4.12.2(Tear Strength)	-	52900	-
4.11.1(Thickness )	-	52900	-
4.10.3(Water absorption & desorption percent)	-	52900	-
4.10.2(Abrasion resistance )	-	52900	-
4.8(Thickness Toe puff & counter stiffener)	-	52900	-
4.7.5(Water Vapour permeability & coefficient )	-	52900	-
4.10.1(Meterial )	-	52900	-
4.9.2(Abrasion resistance )	-	52900	-
4.9.1(Thickness)	-	52900	-
4.7.4(Abrasion resistance )	-	52900	-
4.7.3(Tear Strength)	-	52900	-
4.7.2(Meterial Counter & Toungue)	-	52900	-
4.7.1(Meterial vamp & Quarter)	-	52900	-
4.6.3(Water Penetration and water absorption )	-	52900	-
4.6.2(Tear Strength)	-	52900	-
4.6.1(Thickness )	-	52900	-
4.5.8(Energy absorption of seat region )	-	52900	-
4.5.7(Cold Insulation of sole complex)	-	52900	-
4.5.6(Heat Insulation of sole Complex)	-	52900	-
4.5.5(Antistatic test)	-	52900	-
4.5.4(Slip Resitance)	-	52900	-
4.5.3.2(Interayer bond strength)	-	52900	-
4.5.3.1(Upper/outsole bond strength)	-	52900	-
4.5.2(Ergonomic Feature)	-	52900	-
4.5.1(Contruction)	-	52900	-
4.4(Height of upper )	-	52900	-
4.3.2(Weight)	-	52900	-
4.3.1(Size)	-	52900	-
4.2(Design )	-	52900	-
Cl. 6, Cl.6.1, 6.1.1 & 6.1.2, 8.6 of IS 15298 part 1,ISO 1817,ISO 4643,(Resistance to fuel oil)	-	52900	-
8, 8.1, 8.2, 8.2.1(Marking)	-	52900	-
Cl.4.6.4(Water Penetration and Water Absorption)	-	52900	-
Cl. 6, Cl.6.1, 6.1.1 & 6.1.2,(Resistance to fuel oil)	-	52900	-
CL.8,8.1, 8.2,8.2.1(Marking)	-	52900	-

Complete

25 Feb, 2027

-
Included w.e.f. 17.07.2023

127

IS 12254 (2021)

POLYVINYLCHLORIDE PVC INDUSTRIAL BOOTS - SPECIFICATION Second Revision

all

46000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2(Size)	-	46000	-
5.3(Height)	-	46000	-
5.4.2(Ergonomic feature)	-	46000	-
5.4.3(Sole bond)	-	46000	-
5.4.4(Slip resistance)	-	46000	-
5.4.5(Leak proofness)	-	46000	-
5.4.6.1(Toe caps General)	-	46000	-
5.4.6.2(Internal length of toecaps)	-	46000	-
5.4.6.3(Corrosion resistance)	-	46000	-
5.4.6.4(Impact resistance)	-	46000	-
5.4.6.5(Compression resistance)	-	46000	-
5.4.7(Colour)	-	46000	-
5.5.1(Upper material)	-	46000	-
5.5.1(Upper Thickness)	-	46000	-
5.5.2(Upper tensile strength)	-	46000	-
5.5.3(Upper flexing)	-	46000	-
5.5.4(Upper Hardness)	-	46000	-
5.6.1(Lining material)	-	46000	-
5.6.2(Lining Tear strength)	-	46000	-
5.6.3(Lining abrasion)	-	46000	-
5.6.4(Lining adhesion with upper)	-	46000	-
5.7.1(Insole material)	-	46000	-
5.7.1(Insole thickness)	-	46000	-
5.7.2(Insole abrasion)	-	46000	-
5.7.3(Water absorption and desorption)	-	46000	-
5.8.2(Eyelets material)	-	46000	-
5.8.2(Lace material)	-	46000	-
5.8.2(Lace length)	-	46000	-
5.8.2(Lace breaking load)	-	46000	-
5.9.1(Insock material)	-	46000	-
5.9.2(Inscok abrasion resistance)	-	46000	-
5.9.3(Insock water absorption and desorption)	-	46000	-
5.8.2(Closing thread breaking load)	-	46000	-
5.11.1(Outsole material)	-	46000	-
5.11.1(Outsole thickness)	-	46000	-
5.11.2(Outsole density)	-	46000	-
5.11.3(Outsole Interlayer bond)	-	46000	-
5.11.4(Outsole tear)	-	46000	-
5.11.5(Outsole Abrasion)	-	46000	-
5.11.6(Outsole hardness)	-	46000	-
5.11.7(Outsole flexing)	-	46000	-
5.4.8.1(Conductive Footwear)	-	46000	-
5.4.8.2(Antistatic Footwear)	-	46000	-
5.4.8.3.2(Penetration resistance)	-	46000	-
5.4.8.4(Cut resistance)	-	46000	-
5.5.5(Upper Cold flex resistance)	-	46000	-
5.4.8.5(Outsole resistance to acid and alkali)	-	46000	-
5.4.8.6(Outsole resistance to fuel oil)	-	46000	-
5.11.8(Outsole cold flex resistance)	-	46000	-
6.1(Volatility)	-	46000	-
6.2(Lead content)	-	46000	-
Table 1 as per IS 17011 2018(pH)	-	46000	-
Table 1 as per IS 17011 2018(Phthalates (each individual phthalate))	-	46000	-
Table 1 as per IS 17011 2018(Nickel, on skin contact)	-	46000	-
Table 1 as per IS 17011 2018(Allergenic and carcinogenic disperse dyes)	-	46000	-
Table 1 as per IS 17011 2018(Aromatic amines released from Azo dyes (each individual amine))	-	46000	-
Table 1 as per IS 17011 2018(Aromatic amines released from Azo dyes (each individual amine))	-	46000	-
Table 1 as per IS 17011 2018(Chromium (VI))	-	46000	-
Table 1 as per IS 17011 2018(Dimethyl fumarate (DMFU))	-	46000	-
Table 1 as per IS 17011 2018(Formaldehyde (free or released by partial hydrolysis))	-	46000	-
Table 1 as per IS 17011 2018(Formaldehyde)	-	46000	-
Table 1 as per IS 17011 2018(Organotin compounds)	-	46000	-
Table 1 as per IS 17011 2018(PCP-TeCP-TriCP polychlorophenols)	-	46000	-
5.10(Closing Thread (If used))	-	46000	-

Complete

25 Feb, 2027

-
Included w.e.f. 17.07.2023

128

IS 3976 (2018)

Safety Rubber Canvas Boots for Miners Ã¢â‚¬ Specification ( Sixth Revision )

all

15800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.5.2.5 Compact Sole Heel Cl.5.2.5.1 IS 3400 (Part 2)(requirements prescribed in col 3 of Table 2 when tested as per corresponding test methods prescribed in col 4 of Table 2. i)i) Hardness (IRHD)	-	15800	-
Cl.6.3 Tear Strength of Compact Outsole( When outsoles are tested in accordance to 8.2 of IS 15298 (Part 1), the tear strength shall be not less than 8 kN/m for material having density higher than 0.9/cm³ and when density of material is less than or equal to 0.9 g/cm³, tear strength shall not be less than 5 kN/m.)	-	15800	-
Cl.5.2.3 Coated Binding Material IS 1954( Coated binding materials shall conform to the requirements given in col 3 of Table 1 when tested according to the methods prescribed in col 4 of Table 1. i)Width in mm, )	-	15800	-
Cl.5.2.1.4 ( Type 2 footwear, the composite upper material shall comply with requirements of water coefficient as prescribed in 5.4.6 of IS 15298 (Part 2).)	-	15800	-
Cl.5.13 Energy Absorption Test(When footwear is tested in accordance with the method prescribed in 5.14 of IS 15298 (Part 1), the energy absorption of the seat region shall not be less than 20 J.)	-	15800	-
Cl.5.2.3 Coated Binding Material Annex C(ii) Breaking load in N, Min (50 cm grip length test specimen) )	-	15800	-
Cl.5.2.1.4 ( Type 2 footwear, the composite upper material shall comply with requirements of water vapour permeability as prescribed in 5.4.6 of IS 15298 (Part 2).)	-	15800	-
CL.5.2.10 Counter Stiffener( A counter stiffener, made out of textile reinforced withpolymer/rubber including (thermoplastic) having thickness not less than 1.5 mm is to be stitched at inside of upper so as to fortify the back of the footwear at joints of quarter.)	-	15800	-
Cl.5.1.1 Fittings(Fittings of the footwear shall be in conformity to Table 9 of IS 1638 (measurement of men’s lasts) and Table 8 of IS 1638 (measurement of women’s lasts).)	-	15800	-
Cl.5.2.1 Upper Cl.5.2.1.1 IS 3400(Part 5)( Composite upper material shall comply with consolidation test as per 5.10.(IS 3400 (Part 5). There shall be no separation at a load of 1.5 kg.))	-	15800	-
Cl.5.2.1.2( Composite upper material shall comply with tear strength as per 5.4.3 of IS 15298 (Part 2).)	-	15800	-
Cl.5.2.1.3 , Cl.6.5 of IS 15298 (Part 1).( Composite upper material shall develop no cracks before 150 000 cycles when tested in accordance with 6.5 of IS 15298 (Part 1).)	-	15800	-
Cl.5.2.1.5( Inner layer of upper shall meet requirement of abrasion resistance as prescribed in 5.5.2 of IS 15298 (Part 2).)	-	15800	-
Cl.5.2.2 Compact Insole/Compact Insocks/Counter Stiffener Lining(Textile material shall be used as lining material for compact insole/compact insocks / counter stiffener. It shall meet the requirement of tear strength as prescribed in 5.6.1 of IS 15298 (Part 2).)	-	15800	-
Cl.5.2.2.1 Abrasion resistance of compact insole/insocks/ counter stiffener( When textiles used as lining for all the above are tested in accordance with 6.12 of IS 15298 (Part 1), the lining shall not develop any holes before the following number of cycles has been performed:)	-	15800	-
Cl.5.2.3.1 In case of cotton black binding materia( the same shall be free from sulphur dyes when tested in accordance with Annex B.)	-	15800	-
Cl.5.2.5 Compact Sole Heel Cl. 5.2.5.1 (The compact sole heel shall be made out of polymeric/rubber components and the typical design recommendation (not mandatory) of compact sole heel is as shown in Fig. 3. Sectional view of Type 1/Type 2 ) toe position is given in Fig. 4.)	-	15800	-
Cl.5.2.5 Compact Sole Heel 5.2.5.1 IS 3400 (Part 4)(ii)*Change in hardness after accelerated ageing at 100 ± 2 °C for 24 h )	-	15800	-
Cl.5.2.5.3 Ageing for whole footwear(When rubber is used for manufacturing boots or when the outer sole heel is made of bi-polymer, the finished boots shall be aged at 100 ± 2°C for 24 h. On completion of test, all rubber components shall not develop any sign of tackiness or brittleness.)	-	15800	-
Cl.5.2.5.4 Thickness of compact sole hee(Thickness of compact sole heel of the boots shall comply with the thickness and material requirements prescribed in Table 3.)	-	15800	-
Cl.5.2.5.4 Thickness of compact sole hee(of black cotton thread, the same shall be free from sulphur dyes when tested in accordance with Annex B.)	-	15800	-
Cl.5.2.6 Thread for Upper Closing( The length (m/kg) and construction of sewing thread shall conform to requirements as prescribed in Table 4.)	-	15800	-
Cl.5.2.7 Safety Toe Cap(Safety toe cap as per 3.6 shall be fitted into the footwear and must not come out while in use.)	-	15800	-
Cl.5.2.8.1( The boots shall be provided with laces having minimum length of 115 cm for Type 1 and minimum 100 cm for Type 2.)	-	15800	-
Cl.5.2.8.2 (Minimum breaking load of 60 kg is to be achieved when tested between 18 cm grip length in accordance with Annex C.)	-	15800	-
Cl.5.2.8.3( In case of cotton lace of black colour, the same shall be free from sulphur dyes when tested in accordance with Annex B. Two ends of the laces shall be provided with plastic tips.)	-	15800	-
Cl.5.2.9 Eyelets( Aluminum eyelets of external collar diameter not less than 10 mm and wall thickness of 0.30 to 0.35 mm shall be used.)	-	15800	-
Cl.5.3.2 (The tongue shall be made out of composite upper material and shall be half bellow type for Type 2 and full bellow type for Type 1.)	-	15800	-
Cl.5.3.5 Outer toe cap( shall be provided which is made of polymer/rubber and it shall be strongly adhered such that it shall not open up or come out while in use. Toe of the boot shall be reinforced with safety toe cap)	-	15800	-
Cl.5.3.6( A designed foxing of width of minimum 25 mm and of thickness of minimum 2 mm is to be provided. The foxing shall not extend the edges of the outer sole.)	-	15800	-
Cl.5.3.7( Two pairs of detachable insocks are to be provided. The insocks shall be compact in nature having thickness not less than 2 mm.)	-	15800	-
Cl.5.4 Finish( In appearance, general workmanship and in all other respects with regard to finish and get up of the footwear, the footwear shall be matching to the approved sample of the purchaser.)	-	15800	-
Cl.5.5 Mass(The mass of one pair of finished footwear of size 8 shall not exceed 1 500 g for Type 1 and 1 400 g for Type 2 with an increase or decrease of 100 g for each bigger or smaller size, respectively.)	-	15800	-
Cl.5.6( Height of Upper Height of upper of the boots shall conform to column 5 (Design C) and column 4 (Design B) of 5.2.2, Table 4 of IS 15298 (Part 2) for Type 1 and Type 2, respectively when measured as per 6.2 of IS 15298 (Part 1) on the inside of the back of the footwear and from seat of the insole to top edge of the upper.)	-	15800	-
Cl.5.7 Performance Test(When safety footwear is tested in accordance with the method described in 5.4 of IS 15298 (Part 1), at an impact energy of (200 ± 4) J, the clearance under the toecap at the moment of impact shall be in accordance with Table 5. In addition, the toecap shall not develop any cracks which go through the material, that is, through which light can be seen.)	-	15800	-
Cl.5.8 Upper/Outsole Bond Strength(When the footwear is tested in accordance with the method prescribed in 5.2 of IS 15298 (Part 1), the bond strength shall not be less than 4.0 N/mm, unless there is tearing of the sole in which case the bond strength shall not be less than 3.0 N/mm.)	-	15800	-
Cl.5.9 Sole Interlayer Bond Strength for Bi-polymer( and Bi-density Sole When tested in accordance with 5.2 of IS 15298 (Part 1), the bond strength between the outer or cleated layer and the adjacent layer shall not be less than 4.0 N/mm unless there is tearing of any part of the sole, in which case the bond strength shall not be less than 3.0 N/mm.)	-	15800	-
Cl.5.10 Consolidation Test( Representative sample of width 25 ± 0.5 mm are cut out from the quarter of the upper along the length of boot. The plies are separated by breaking the bond. Carry out the test on two specimens in accordance with IS 3400 (Part 5). Th)	-	15800	-
Cl.5.11 Compression Resistance( 5.11.1 When safety boots are tested in accordance with 5.5 of IS 15298 (Part 1), the clearance under the toe cap at a compression load of 15 kN ± 0.1 kN shall be in accordance with Table 5.)	-	15800	-
Cl.5.12 Internal Length of Toe Cap( For safety boots, internal length of the toe cap shall meet the specification given in Table 5 of IS 15298 (Part 2) when tested as per 5.3 of IS 15298 (Part 1).)	-	15800	-
Cl.6.1 Abrasion Resistance of Compact Outsole( When outsole is tested in accordance with 8.3 of IS 15298 (Part 1), the relative volume loss shall not be greater than 250 mm³ for materials having density 0.9 g/cm³ or less, and not greater than 150 mm³ for materials with density greater than 0.9 g/cm³.)	-	15800	-
Cl.6.2 Flexing Resistance of Compact Outsole( When outsole is tested in accordance with 8.4 of IS 15298 (Part 1), the cut growth shall not be greater than 4 mm before 30 000 cycles.)	-	15800	-
Cl.6.4 Resistance to Hot Contact( — Sole Heel When sole heel is tested in accordance with 8.7 of IS 15298 (Part 1), the material shall not melt/deform and shall not develop any cracks when bent around the mandrel.)	-	15800	-
Cl.6.5 Hydrolysis( When bottom sole or other components are made out of polyurethane, the same shall be tested in accordance with 8.5 of IS 15298 (Part 1) and the same shall comply with 5.8.5 of IS 15298 (Part 2).)	-	15800	-
4(Types)	-	15800	-
5(Requirements)	-	15800	-
5.1(Design)	-	15800	-
5.10(consolidation test IS 3400 (Part 5))	-	15800	-
5.2.4(Reinforcing Material)	-	15800	-
5.2.8.4(Colour of the lace)	-	15800	-
5.3, 5.3.1,5.3.3,5.3.4(Construction)	-	15800	-
8(CHEMICAL REQUIREMENTS)	-	15800	-
9, 9.1(BIS CERTIFICATION MARKING)	-	15800	-
10(Marking)	-	15800	-
11(Packing)	-	15800	-
7.1(Resistance to fuel)	-	15800	-
7.2(Resistance to electricity)	-	15800	-

Complete

25 Feb, 2027

-
Included w.e.f. 17.07.2023

129

IS 3736 (1995)

Canvas boots, rubber sole - Specification (Second Revision)

18000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4.1.7.4 Ageing(The boots shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the soles and heels of the boots shall conform to the physical requirements prescribed in Table 5. i) Tensile Length)	-	18000	-
Cl.4.1.7.4 Ageing(ii) Elongation at break)	-	18000	-
Cl.4.1.7.2 IS 3400 (Part 2) : 1980(2)Hardness, IRHD)	-	18000	-
4.1.6 Fabric Laces Cl.4.1.6.1( The boots shall be provided with braided of cotton or man made or blended fabric laces 115 ± 5 cm in length, matching the colour of the upper. )	-	18000	-
Cl.4.1.1 upper IS 1969(d) Picks/dm)	-	18000	-
Cl.4.4.5 ( Table 1.)(d) Picks/dm)	-	18000	-
4.1.2 Lining Material(195 ± 5 picks/dm shall be used.)	-	18000	-
Cl.4.1.1 upper IS 1969(c) Ends/dm )	-	18000	-
Cl.4.4.5 ( Table 1.)(c) Ends/dm )	-	18000	-
4.1.2 Lining Material(having 390 ± 10 ends/dm and )	-	18000	-
Cl.4.1.7.2 IS 3400 (Part 4) : 1987 IS 3400 (Part 2) : 1980(Change in initial hardness after accelerated ageing for 24 h at l00 ± 1°C)	-	18000	-
Cl.4.8 Adhesion Test(From the upper foxing portion where it is adhered to the canvas cut a strip of 8.0 ± 0.5 mm width along with the length of the sole at the waist portion and of sufficient lengh to permit separation over a length of at least 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10 mm per minute in accordance with IS 3400 (Part 5):1986 or the Static Dead Load Method as given in Annex C. The individual adhesion value noted/recorded shall not be less than 8 N (0.8 kgf) for each of the test pieces ( see Note under 4.7 ).')	-	18000	-
Cl.4.4.9(From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine)	-	18000	-
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Tensile strength in MPa, Min)	-	18000	-
Cl.4.1.3 Binding Material IS 1954:1990(Cotton tape NEWAR used as binding material shall conform to the requirements as mentioned in Table 2, when tested in accordance with the methods referred to in col 4 of Table 2. 1)Width, mm. Min )	-	18000	-
Cl.4.4.3(The top, side and front edges of the quarters and tongue shall be bound with cotton tape NEWAR of not less than 13 mm width using variety No. 29 thread.)	-	18000	-
Cl.4.1.7.3 IS 3400 (Part 10) : 1977(Compression set, in percent. Max)	-	18000	-
Cl.4.4.4( The back of the quarter shall be reinforced with a strip, not less than 25 mm wide,of either upper material or canvas. In case of composite upper material the edges of the strip shall be bound by cotton tape ( NEWAR ). When canvas cloth is used the edges shall be folded and shall be stitched with two rows of stitching.)	-	18000	-
Cl.4.7 Consolidation Test(From the quarter, cut a strip of 25.0 ± 0. 5 mm width along the length of the boot and of sufficient length to permit separation over a length of 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10mm per minute in accordance with IS 3400 (Part 5): 1986 or Static Dead Load Method as given in Annex C. The individual adhesion value for consolidation test shall not be less than 30 N (3.0 kgf) for each of the test pieces)	-	18000	-
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Elongation at break, in percent, Min)	-	18000	-
IS 1969:1985(Breaking load on 50 cm test length. N, Min)	-	18000	-
4.1.6 Fabric Laces Cl.4.1.6.1(The laces shall have a minimum breaking load of 450 N, when tested between 18 cm grips, the rate of traverse of power actuated grip being 30 cm/min.)	-	18000	-
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles b)Cut growth at the end of 150 000 cycles, Percent, Max)	-	18000	-
Cl.4.4.5 ( Table 1.)(b) Weft )	-	18000	-
Cl.4.4.5 ( Table 1.)( in case of half bellow. Thefull bellow tongue shall be made out of canvas cloth as prescribed in Sl No. (i) of Table 1. Breaking load in N, Min a) Warp )	-	18000	-
Cl.4.1.1 upper IS 1969(b)Weft)	-	18000	-
Cl.4.1.1 upper IS 1969(Breaking load in N.Min (5 × 20 cm grip): a) Wrap)	-	18000	-
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles a)Initial crack, Min)	-	18000	-
4.1.2 Lining Material( 200 N Minin weft way (when tested in accordance with IS 1969 : 1985) )	-	18000	-
4.1.2 Lining Material(For covering of the insole, cotton drill conforming to Table 1, Sl No. (ii) shall be used. For detachable insole, bleached cotton twill of breaking load 390 N Min in warp way and)	-	18000	-
Cl.4.1.1 upper(The upper shall consist of Rip Stop Fabric of cotton or manmade or its blend being the over layer and cotton drill as an inner layer and shall conform to the requirements given at Sl No. (i) of Table 1. Sr.no 1.Overlayer Construction )	-	18000	-
4.1.1.1 Colour fastness(The dyed fabrics prescribed in 4.1.1 shall be fast to daylight and mechanical washing. Fastness to daylight shall be of rating 4 or better, when tested in accordance with IS 686 : 1985 or IS 2454 : 1985.)	-	18000	-
Cl.4.1.1.2( Fastness to mechanical washing (mild) shall be of rating 4 or better, when tested in accordance with IS 764 : 1979)	-	18000	-
Cl.4.1.3.3( Black tapes shall be free from sulphur dyes when tested in accordance with Annex B.)	-	18000	-
Cl.4.1.4 Reinforcement Material(The back seam, joining two quarters at the back of the heel shall be reinforced with a not less than 25 mm wide tape made out of material conforming to Sl No. (i) of Table 1)	-	18000	-
Cl.4.1.5 Thread for Upper Closing Cl.4.1.5.1 (IS 1670:1991)(Sewing thread cotton, man made or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirements. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirement of specification.')	-	18000	-
Cl.4.1.5.2( The colour of the threads shall be asagreed to between the purchaser and the supplier. The dyed threads shall conform to the following requirements)	-	18000	-
4.1.6 Fabric Laces Cl.4.1.6.1(The two ends of the lace shall be provided with suitable metal or plastic tips. Black laces shall be free from sulphur dyes when tested in accordance with Annex B.)	-	18000	-
Cl.4.1.7 Rubber Components Cl.4.1.7.1( the soles and heels shall conform to Type 2 of IS 5676:1995.)	-	18000	-
Cl.4.1.7.2 IS 3400 (Part 9) : 1978( The rubber components shall conform to Table 4 when tested.' ( Page 3, Table 4, Note 1) — 'However in case it is not possible then 4.2.5.3 of IS 13695:1993 shall be followed. 1)Relative density, Max)	-	18000	-
Cl.4.1.7.5 Thickness of components(Individual components of the boots shall comply with the thickness and material requirements prescribed in Table 6.)	-	18000	-
Cl.4.3 Leg Height(The leg height of the boots for size 8 shall be 160 ± 2 mm with an increase or decrease of 4 mm of the nominal height for each bigger or smaller sizes respectively when measured at the inside from the back of the boot from insole to the top.)	-	18000	-
Cl.4.4.2( The canvas upper shall be lined with bleached drill cloth.)	-	18000	-
Cl.4.4.3( The upper shall be stitched on a lockstitch machine, with 30 to 40 stitches per decimetre by thread of variety No. 8 and variety No. 29 cotton sewing thread conforming to 4.1.5 using variety No. 29 for taping and binding and variety No. 8 for remaining seams. )	-	18000	-
Cl.4.4.5 ( The tongue shall be either half or full bellow depending on the requirement of the purchaser andshall be made from composite material prescribed for the upper in 4.1.1.)	-	18000	-
Cl.4.4.6( A minimum of seven aluminium, brass or steel eyelets having 10 mm diameter and wall thickness 0.30 to 0.35 mm shall be fitted in each face.')	-	18000	-
Cl.4.4.7( The toe shall be reinforced with a toe puff cemented inside and outside with rubber toe cap. The heel piece (counter) or stiffener shall be set from the bottom of the lining and bound flat on the top edge with white cloth for binding of countertop edge with white clothfor binding of counter)	-	18000	-
Cl.4.4.8( A strengthening rubber arch piece shall be firmly pasted and stitched at the middle arch of the inside quarter. Another strengthening rubber piece, circular in shape 35 ± 1 mm in diameter, may bepasted and stitched at the centre of the inside)	-	18000	-
Cl.4.4.10( A 25 mm Min wide and 2 mm Min thick rubber golosh in serrated, diamond or any otherdesign, as agreed to between the purchaser and thesupplier, shall be fitted all round the sole edge of the boot. The golosh shall not extend below the edge of the sole.)	-	18000	-
Cl.4.5.1(Cl.4.1.6.)( Each pair of boot shall be provided with a pair of braided fabric laces of the quality as prescribed in 4.1.6.)	-	18000	-
Cl.4.5.2( In appearance, general workmanship, finish and in all other respects, not defined in this standard, the boot shall be similar to those of the sample approved by the purchaser, if any.)	-	18000	-
Cl.4.6 Mass(The mass of finished boots, rubber sole, of size 8 shall not exceed 1130 g per pair, and the mass shall increase or decrease by 75 g per pair for each bigger or smaller size respectively.)	-	18000	-
Cl.4.9 Composite Breaking Strength Test( From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine.Rate of traverse of pulling jaw shall be 100 ± 5 mm per minute. Two such test pieces will be required to be obtained from the made up footwear and will be subjected to test to break each test piece. Mean value of each set of test pieces comprising of length wise and height wise test pieces will be 1 000 N/25 mm width minimum.')	-	18000	-

Complete

25 Feb, 2027

-
Included w.e.f. 17.07.2023

130

IS 17043 (2018)

Derby shoes - Specification

all

52900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.0(Innocuosness test IS 17011)	-	52900	-
4.15.2(Breaking load & tag retention)	-	52900	-
4.15.1(Length of laces )	-	52900	-
4.14(Eyelet pull out test)	-	52900	-
4.13.8(Flex resistance )	-	52900	-
4.13.7(Abrasion resistance )	-	52900	-
4.13.6(Tear Strength)	-	52900	-
4.13.5(Ageing test)	-	52900	-
4.13.4(Hardness (IRHD))	-	52900	-
4.13.3(Density )	-	52900	-
4.13.2(Thickness )	-	52900	-
4.13.1(Meterial)	-	52900	-
4.12(Breaking Strength of thread)	-	52900	-
4.11.2(Tear Strength)	-	52900	-
4.11.1(Thickness )	-	52900	-
4.10(Toe Puff & counter stiffener thickness )	-	52900	-
4.9.3(Abrasion resistance )	-	52900	-
4.8.3(Water absorption & desorption )	-	52900	-
4.9.1(Thickness )	-	52900	-
4.8.2(Abrasion )	-	52900	-
4.8.1(Thickness )	-	52900	-
4.7.4(Water vapour permeability & coefficent )	-	52900	-
4.7.3(Abrasion resistance )	-	52900	-
4.7.2(Tear Strength)	-	52900	-
4.7.1(Thickness )	-	52900	-
4.6.4(Water penetration and water absorption)	-	52900	-
4.6.3(Water vapour permeability & coefficent )	-	52900	-
4.6.2(Tear Strength)	-	52900	-
4.6.1(Thickness )	-	52900	-
4.5.8(Energy absorption of seat region )	-	52900	-
4.5.7(Cold insulation tester )	-	52900	-
4.5.6(Heat insulation of sole complex)	-	52900	-
4.5.5.1(Electrical Properties Antistatic )	-	52900	-
4.5.4(Slip Resitance)	-	52900	-
4.5.3.2(Interayer bond strength)	-	52900	-
4.5.3.1(Upper/outsole bond strength)	-	52900	-
4.5.2(Ergonomic Feature)	-	52900	-
4.5.1(Contruction)	-	52900	-
4.4(Height of upper )	-	52900	-
4.3.2(Weight)	-	52900	-
4.3.1(Size)	-	52900	-
4.2(Design )	-	52900	-
4.1(General)	-	52900	-
4.1, Table 1(Physical Requirements for Derby Shoes)	-	52900	-
4.3.2., Table 2(Maximum Weight of Derby Shoe Pair)	-	52900	-
4.4, Table 3(Height of the Upper)	-	52900	-
4.5.3(Bond Strength)	-	52900	-
4.9(Insocks)	-	52900	-
6.1(Scale of Sampling)	-	52900	-
6.2(Methods of Selecting Footwear)	-	52900	-
6.3.1(Visual and Tactile Examination)	-	52900	-
6.3.2(Dimensional Characteristics)	-	52900	-
6.3.3.1(Tests for physical requirements)	-	52900	-
6.3.3.2(Tests for chemical requirements)	-	52900	-
7(Marking)	-	52900	-
6.1.3, Table 4(Scale of Sampling and Permissible Number of Defectives for Tests on Whole Footwear)	-	52900	-
4.14(Colour peeling test)	-	52900	-
4.6.1(Upper Material)	-	52900	-
4.7.1(Lining Material)	-	52900	-
4.8.1(Insole Material)	-	52900	-
4.9.1(Insocks Material)	-	52900	-
4.11.1(Tongue Material)	-	52900	-
4.13.1(Outsole Material)	-	52900	-
4.14(Eyelet Material)	-	52900	-
4.15.1(Laces Material)	-	52900	-
4.10(Toe Puff and Counter Stiffener Material and thickness)	-	52900	-

Complete

25 Feb, 2027

-
Included w.e.f. 17.07.2023

131

IS 10702 (2023)

Hawai Chappal-Specification

all

40100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Material)	-	40100	-
4.2(Length)	-	40100	-
4.3(Thickness)	-	40100	-
4.4 , Table No. 1 , i)(Density)	-	40100	-
4.4 , Table No. 1 , ii)(2Compression set at constant stress)	-	40100	-
4.4 , Table No. 1 , iii)(3Split tear strength)	-	40100	-
4.4 , Table No. 1 , iv)("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber")	-	40100	-
4.4 , Table No. 1 , v)(5Abrasion resistance at applied force)	-	40100	-
4.4 , Table No. 1 , vi)(Flexing resistance: Maximum cut growth at 50 000 flexes)	-	40100	-
4.4 , Table No. 1 , vii)(7 Hydrolysis resistance, Maximum cut growth at 50 000 flexes)	-	40100	-
4.4 , Table No . 2 , i)(Density , Solid strap, Cellular strap)	-	40100	-
4.4 , Table No . 2 , ii)("Breaking strength , Strap to strap and Toe portion to strap , Elongation at break")	-	40100	-
4.4 , Table No . 2 , iii)(Minimum cross section of the stud)	-	40100	-
4.4 , Table No . 2 , iv)(Stud bolt)	-	40100	-
4.4 , Table No . 3 , i)(Toe post attachment strength)	-	40100	-
4.4 , Table No . 3 , ii)(Attachment strength of rear strap)	-	40100	-
4.4 , Table No . 3 , iii)(Inter layer bond strength)	-	40100	-
5(CHEMICAL REQUIREMENT FOR HAWAI CHAPPAL)	-	40100	-
6(MARKING AND PACKING)	-	40100	-
Cl. No.5.1,Table no.1 of IS 17011(i)(Allergenic and carcinogenic disperse dyes)	-	40100	-
Cl. No.5.1,Table no.1 of IS 17011(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	40100	-
Cl. No.5.1,Table no.1 of IS 17011(iv)(Chromium (VI))	-	40100	-
Cl. No.5.1,Table no.1 of IS 17011(v)(Dimethyl fumarate (DMFU))	-	40100	-
Cl. No.5.1,Table no.1 of IS 17011(vi)(Formaldehyde (free or released by partial hydrolysis))	-	40100	-
Cl. No.5.1,Table no.1 of IS 17011(vii)(Formaldehyde)	-	40100	-
Cl. No.5.1,Table no.1 of IS 17011(viii)(Organotin compounds)	-	40100	-
Cl. No.5.1,Table no.1 of IS 17011(ix)(PCP-TeCP-TriCP polychlorophenols)	-	40100	-
Cl. No.5.1,Table no.1 of IS 17011(x)(pH)	-	40100	-
Cl. No.5.1,Table no.1 of IS 17011(xi)(Phthalates (each individual phthalate))	-	40100	-
Cl. No.5.1,Table no.1 of IS 17011(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	40100	-
Cl.No. 5.2(lead content)	-	40100	-

Complete

25 Feb, 2027

-
Included w.e.f. 17.07.2023 Amendment No. 1 included w.e.f. 26.03.2024

132

IS 6721 (2023)

SANDAL AND SLIPPERS SPECIFICATION First revision

45100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No.4(SHAPE AND DESIGN)	-	45100	-
Cl. No.5("SIZE AND FITTINGS ")	-	45100	-
Cl. No.6("CONSTRUCTION ")	-	45100	-
Cl. No.7(MATERIAL)	-	45100	-
Cl. No.8.1, Table no. 1(i),a("Tear strength, (other than moulded upper material) ")	-	45100	-
Cl. No.8.1, Table no. 1(i),b("For all moulded upper material ")	-	45100	-
Cl. No.8.1, Table no. 1(ii)(Flexing endurance)	-	45100	-
Cl. No.8.2,Table no. 2(i)(Tear strength)	-	45100	-
Cl. No.8.2,Table no. 2(ii),a("Abrasion resistance- At dry condition")	-	45100	-
Cl. No.8.3,Table no. 3(ii),b("Abrasion resistance- At wet condition")	-	45100	-
Cl. No.8.3,Table no. 3(i)(Tear strength)	-	45100	-
Cl. No.8.3,Table no. 3(ii),a("Abrasion resistance- At dry condition")	-	45100	-
Cl. No.8.4,Table no. 4(i)(Grain crack index)	-	45100	-
Cl. No.8.4,Table no. 4(ii)(Density)	-	45100	-
Cl. No.8.4,Table no. 4(iii)(Abrasion resistance)	-	45100	-
Cl. No.8.4,Table no. 5(i)(Density)	-	45100	-
Cl. No.8.4,Table no. 5(ii)("Abrasion resistance, Volume loss ")	-	45100	-
Cl. No.8.4, Table no. 5(iii)("Flexing resistance, At 30 000 flexes")	-	45100	-
Cl. No.8.5, Table no. 6(i)("Bond strength, N/mm, Min (Applicable when fore part is fully covered or strap width is more than 25 mm)")	-	45100	-
Cl. No.8.5, Table no. 6(ii)("Toe post attachment strength, N, Min (Applicable if toe post is present)")	-	45100	-
Cl. No.8.5, Table no. 6(iii)("Toe ring attachment strength, Min (Applicable if toe ring is not integral part of upper")	-	45100	-
Cl. No.8.5, Table no. 6(iv)(Strap to outsole strength)	-	45100	-
Cl. No.8.5, Table no. 6(v)("Attachment strength of back strap and Buckle/D-ring ")	-	45100	-
Cl. No.8.5, Table no. 6(vi)("Attachment strength of elastic, limit of useful extension, percent")	-	45100	-
Cl. No.8.5, Table no. 6(vii)("Attachment strength of back strap and velcro, N, Min (If, present)")	-	45100	-
Cl. No.8.5, Table no. 6(viii)("Hydrolysis resistance, Cut growth after 150 000 flexes, mm, Max (Applicable for PU sole only)")	-	45100	-
Cl. No.8.5, Table no. 6(ix)("Heel pull off strength, N, Min (Applicable for heel height 40 mm and above attached separately to the sandal/slipper)")	-	45100	-
Cl. No.8.5, Table no. 6(x)("Inter layer bond strength, N/mm, (Applicable for multi-layer sole)")	-	45100	-
Cl. No.8.5, Table no. 6(xi)("Slip Resistance, Coefficient of Friction (COF) (Not applicable for leather sole) (To be carried out on quarry tiles)")	-	45100	-
Cl. No.8.("Requirement of Complete Sandal and Slipper (Chemical Requirements) ")	-	45100	-
Cl. No.9.(MARKING AND PACKING)	-	45100	-
Cl. No.8.6.1,Table 1 of IS 17011(i)(Allergenic and carcinogenic disperse dyes)	-	45100	-
Cl. No.8.6.1,Table 1 of IS 17011(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	45100	-
Cl. No.8.6.1,Table 1 of IS 17011(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	45100	-
Cl. No.8.6.1,Table 1 of IS 17011(iv)(Chromium (VI))	-	45100	-
Cl. No.8.6.1,Table 1 of IS 17011(v)(Dimethyl fumarate (DMFU))	-	45100	-
Cl. No.8.6.1,Table 1 of IS 17011(vi)(Formaldehyde (free or released by partial hydrolysis))	-	45100	-
Cl. No.8.6.1,Table 1 of IS 17011(vii)(Formaldehyde)	-	45100	-
Cl. No.8.6.1,Table 1 of IS 17011(viii)(Organotin compounds)	-	45100	-
Cl. No.8.6.1,Table 1 of IS 17011(ix)(PCP-TeCP-TriCP polychlorophenols)	-	45100	-
Cl. No.8.6.1,Table 1 of IS 17011(x)(pH)	-	45100	-
Cl. No.8.6.1,Table 1 of IS 17011(xi)(Phthalates (each individual phthalate))	-	45100	-
Cl. No.8.6.1,Table 1 of IS 17011(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	45100	-
Cl. No.8.6.2(Lead content)	-	45100	-

Complete

25 Feb, 2027

-
Included w.e.f. 17.07.2023 Amendment No. 1 included w.e.f. 26.03.2024

133

IS 15844 : Part 1 (2023)

SPORTS FOOTWEAR PART -1 GENERAL PURPOSEFirst Revision

all

59200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl No.4.1(Sampling and Conditioning)	-	59200	-
Cl No.4.2(Construction)	-	59200	-
Cl No.4.3(Whole Footwear)	-	59200	-
4.3.1(Insole)	-	59200	-
4.3.2(Toe spring height)	-	59200	-
4.3.3(Upper to Mid Sole/Out Sole Bond Performance)	-	59200	-
4.3.4("Upper to Composite Sole Bond Performance (Applicable Only When the Sole is Composite)")	-	59200	-
4.3.5(Out Sole to Mid Sole (Multilayer) Bond Performance)	-	59200	-
4.3.6(Energy Absorption at Seat Region)	-	59200	-
4.3.7(Complete Shoe Flexing)	-	59200	-
4.3.8(Washability)	-	59200	-
4.3.9(Slip Resistance)	-	59200	-
Cl No.4.4 , Table No. 2 , i) , a)(Flexing resistance, Dry condition)	-	59200	-
Cl No.4.4 , Table No. 2 , i) , b)(Flexing resistance, Wet condition)	-	59200	-
Cl No.4.4 , Table No. 2 , ii)(Tear strength (average force), Min, N)	-	59200	-
Cl No.4.4 , Table No. 2 , iii) , a)("Colour fastness rubbing (To and fro) Grey scale rate, Min , Dry: (rubbing) Rating: (Marring and staining) ")	-	59200	-
Cl No.4.4 , Table No. 2 , iii) , b)("Colour fastness rubbing (To and fro) Grey scale rate, Min , Wet: (rubbing) Rating: (Marring and staining)")	-	59200	-
Cl No.4.4 , Table No. 2 , iv) , a)(Water vapour permeability, mg/cm2h, Min)	-	59200	-
Cl No.4.4 , Table No. 2 , iv) , b)(Water vapour coefficient, mg/cm2 , Min)	-	59200	-
Cl No.4.4 , Table No. 2 , v)(Stitch tear strength (double hole), N/mm, Min)	-	59200	-
Cl No.4.4 , Table No. 2 , vi)("Colour fastness to light (Optional) Grey scale rate, Min Rating: (Marring)")	-	59200	-
Cl No.4.4 , Table No. 2 , i)(Breaking strength, N/mm, Min)	-	59200	-
Cl No.4.4 , Table No. 2 , ii)(Elongation at break, percent Min)	-	59200	-
Cl No.4.4 , Table No. 2 , iii)(Tear strength, N, Min For Fabric: For all other materials)	-	59200	-
Cl No.4.4 , Table No. 2 , iv) , a)(Flexing resistance, Dry condition)	-	59200	-
Cl No.4.4 , Table No. 2 , iv) , b)(Flexing resistance, ,Wet condition)	-	59200	-
Cl No.4.4 , Table No. 2 , v) , a)(Water vapour permeability, mg/cm2h, Min)	-	59200	-
Cl No.4.4 , Table No. 2 , v) , b)("Water vapour coefficient, mg/cm2 , Min ")	-	59200	-
Cl No.4.4 , Table No. 2 , vi)(Hydrolysis resistance)	-	59200	-
Cl No.4.4 , Table No. 2 , vii)(Bursting Strength, kg/cm2 , Min)	-	59200	-
Cl No.4.5 , Table No. 3 , i)(Tear strength, N, Min)	-	59200	-
Cl No.4.5 , Table No. 3 , ii)(Abrasion resistance, cycles)	-	59200	-
Cl No.4.5 , Table No. 3 , iii)("Colour fastness to rubbing (crocking), Grey scale rate with 10 rubs on dry or wet, Min")	-	59200	-
Cl No.4.5 , Table No. 3 , iv)("Colour fastness to perspiration (contact method) Grey scale rate, Min")	-	59200	-
Cl No.4.5 , Table No. 3 , v) , a)(Water vapour permeability, mg/cm2h, Min)	-	59200	-
Cl No.4.5 , Table No. 3 , v) , b)("Water vapour coefficient, mg/cm2 , Min ")	-	59200	-
Cl No.4.6 , Table No. 4 , i)(Thickness, mm, Min)	-	59200	-
Cl No.4.6 , Table No. 4 , ii)(Flexing index, Min)	-	59200	-
Cl No.4.6 , Table No. 4 , iii)(Abrasion resistance, at 400 cycles)	-	59200	-
Cl No.4.6 , Table No. 4 , iv) , a)(Water Absorption, mg/cm2 , Min)	-	59200	-
Cl No.4.6 , Table No. 4 , iv) , b)(Water Desorption, percent, Min)	-	59200	-
Cl No.4.7, Table No. 5 , i)(Thickness, mm, Min)	-	59200	-
Cl No.4.7, Table No. 5 , ii)(Abrasion resistance, cycles)	-	59200	-
Cl No.4.7, Table No. 5 , iii) , a)(Water Absorption, mg/cm2 , Min)	-	59200	-
Cl No.4.7, Table No. 5 , iii) , b)(Water Desorption, percent, Min)	-	59200	-
Cl No.4.8 , Table No. 6 , i)(Abrasion resistance (Volume loss), mm3 , Max)	-	59200	-
Cl No.4.8 , Table No. 6 , ii)("Flexing resistance Belt Method at 90 diameter Mandrel or Bennewart method, cut growth, Max")	-	59200	-
Cl No.4.8 , Table No. 6 , iii)("Hydrolysis resistance, cut growth after 150 000 flexes, in mm, Max")	-	59200	-
Cl No.4.9 , Table No. 7 , i)(Compression set, percent, Max)	-	59200	-
Cl No.4.9 , Table No. 7 , ii)(Split tear strength, kg/25 mm, Min)	-	59200	-
Cl No.4.9 , Table No. 7 , iii)(Heat shrinkage, percent, Max)	-	59200	-
Cl No.4.10 , Table No. 8 , i)(First dry collapsing load, hardness, N, Min)	-	59200	-
Cl No.4.10 , Table No. 8 , ii)(Resilience, percent, Min)	-	59200	-
Cl No.4.10 , Table No. 8 , iii)(Moisture resistance, percent, Min)	-	59200	-
Cl No.4.10 , Table No. 8 , iv) , a)(Initial dry area shape retention, percent, Min)	-	59200	-
Cl No.4.10 , Table No. 8 , iv) , b)(Area shape retention after 10th collapse, dry, percent, Min)	-	59200	-
Cl No.4.11 , Table No. 9 , i)(Peel strength, N/mm, Min)	-	59200	-
Cl No.4.11 , Table No. 9 , ii)(Shear strength, kPa , Min)	-	59200	-
Cl No.4.12 , Table No. 10 , i)(Limit of useful extension, percent, Min)	-	59200	-
Cl No.4.13 , Table No. 11 , i)(Breaking strength of lace, N, Min)	-	59200	-
Cl No.4.13 , Table No. 11 , ii)(Lace tag strength, N, Min)	-	59200	-
Cl No.4.13 , Table No. 11 , iv)("Colour fastness to water Gray Scale Rate, Min Rating")	-	59200	-
Cl No.4.13 , Table No. 11 , v)(Strength of Buckle/Ski hook, N, Min)	-	59200	-
Cl No.4.13 , Table No. 11 , vi)(Corrosion resistance)	-	59200	-
Cl No . 5(MARKING AND PACKING)	-	59200	-
Cl No . 4.14, Table no. 1 of IS 17011(i)(Allergenic and carcinogenic disperse dyes)	-	59200	-
Cl No . 4.14, Table no. 1 of IS 17011(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	59200	-
Cl No . 4.14, Table no. 1 of IS 17011(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	59200	-
Cl No . 4.14, Table no. 1 of IS 17011(iv)(Chromium (VI))	-	59200	-
Cl No . 4.14, Table no. 1 of IS 17011(v)(Dimethyl fumarate (DMFU))	-	59200	-
Cl No . 4.14, Table no. 1 of IS 17011(vi)(Formaldehyde (free or released by partial hydrolysis))	-	59200	-
Cl No . 4.14, Table no. 1 of IS 17011(vii)(Formaldehyde)	-	59200	-
Cl No . 4.14, Table no. 1 of IS 17011(viii)(Organotin compounds)	-	59200	-
Cl No . 4.14, Table no. 1 of IS 17011(ix)(PCP-TeCP-TriCP polychlorophenols)	-	59200	-
Cl No . 4.14, Table no. 1 of IS 17011(x)(pH)	-	59200	-
Cl No . 4.14, Table no. 1 of IS 17011(xi)(Phthalates (each individual phthalate))	-	59200	-
Cl No . 4.14, Table no. 1 of IS 17011(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	59200	-

Complete

25 Feb, 2027

-
Included w.e.f. 17.07.2023 Amendment No. 1 included w.e.f. 26.03.2024

134

IS 15298 : part 4 (2017)

Personal protective equipment: Part 4 occupational footwear (Second Revision)

all

53100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Table 1(CLASS I)	-	53100	-
Table 1(CLASS II)	-	53100	-
5.2.2.1(General)	-	53100	-
5.2.2.2(Height of upper)	-	53100	-
5.2.2.3(Seat region)	-	53100	-
5.3.1.2(Upper/outsole bond strength)	-	53100	-
5.3.2.2(Leakproofness)	-	53100	-
5.3.2.3(Specific ergonomic features )	-	53100	-
5.3.4.1(Slip resistance)	-	53100	-
5.3.4.2(Slip resistance on ceramic tile floor with sodium lauryl sulphate (SLS) solution)	-	53100	-
5.3.4.3(Slip resistance on steel floor with glycerine )	-	53100	-
5.3.4.4(Slip resistance on ceramic tile floor with SLS and on steel floor with glycerine )	-	53100	-
5.3.2.5(Innocuousness )	-	53100	-
5.4.2.1(Upper)	-	53100	-
5.4.2.2(Thickness )	-	53100	-
5.4.2.3(Tear strenth)	-	53100	-
5.4.2.4(Tensile properties)	-	53100	-
5.4.2.5(Flexing resistance )	-	53100	-
5.4.2.6(Water vapour permeability and coefficient )	-	53100	-
5.4.2.7(pH value )	-	53100	-
5.4.2.8(Hydrolysis)	-	53100	-
5.4.2.9(Chromium VI content )	-	53100	-
5.5.2.1(Tear strength )	-	53100	-
5.5.2.2(Abrasion resistance )	-	53100	-
5.5.2.3(Water vapour permeability and coefficient )	-	53100	-
5.5.2.4(pH value )	-	53100	-
5.5.2.5(Chromium VI content )	-	53100	-
5.6(Tongue )	-	53100	-
5.6.2.1(Tear strength )	-	53100	-
5.6.2.2(pH value )	-	53100	-
5.6.2.3(Chromium VI content )	-	53100	-
5.7.2.1(Insole and insock )	-	53100	-
5.7.2.2(Insole and insock )	-	53100	-
5.7.2.3(Water absorption and desorption )	-	53100	-
5.7.4.1(Abrasion resistance )	-	53100	-
5.7.4.2(Abrasion resistance )	-	53100	-
5.7.2.5(Chromium VI content )	-	53100	-
5.8.2.1(Outsole)	-	53100	-
5.8.1.1(Thickness )	-	53100	-
5.8.1.2(Cleated area )	-	53100	-
5.8.1.3(Cleat height)	-	53100	-
5.8.2.2(Tear strength )	-	53100	-
5.8.2.3(Abrasion resistance )	-	53100	-
5.8.2.4(Flexing resistance )	-	53100	-
5.8.2.5(Hydrolysis )	-	53100	-
5.8.2.6(Interlayer bond strength )	-	53100	-
6.2.1.1(Metallic anti-penetration insert )	-	53100	-
6.2.1.1.2(Non-metallic anti-penetration insert used as an insole)	-	53100	-
6.2.1.2(Construction)	-	53100	-
6.2.1.3(Dimensions )	-	53100	-
6.2.1.4(Flex resistance of penetration-resistant inserts )	-	53100	-
6.2.1.5.1(Corrosion resistance of penetration-resistant metallic inserts)	-	53100	-
6.2.1.5.2(Penetration-resistant non-metallic inserts)	-	53100	-
6.2.2.1(Conductive footwear)	-	53100	-
6.2.2.2(Antistatic footwear)	-	53100	-
6.2.2.3(Electrically insulating footwear )	-	53100	-
6.2.3.1(Heat insulation of sole complex )	-	53100	-
6.2.3.2(Cold insulation of sole complex)	-	53100	-
6.2.2.4(Energy absorption of seat region )	-	53100	-
6.2.2.5(Water resistance )	-	53100	-
6.2.2.6(Ankle protection)	-	53100	-
6.2.7.1(Cut resistance foot wear)	-	53100	-
6.2.7.2(Cut resistance foot wear)	-	53100	-
6.2.7.3(Resistance to cutting)	-	53100	-
6.2.7.4(Pentration resistance)	-	53100	-
6.3.2.2(Upper- water penetration)	-	53100	-
6.4.2.1(Resistance to hot contact)	-	53100	-
6.4.2.2(Resistance to fuel oil)	-	53100	-
7(a)(Marking)	-	53100	-
7(b)(Marking)	-	53100	-
7(c)(Marking)	-	53100	-
7(d)(Marking)	-	53100	-
7(e)(Marking)	-	53100	-

Complete

25 Feb, 2027

-
-

135

IS 15298 : Part 3 (2019)

Personal protective equipment: Part 3 protective footwear (Second Revision)

all

53100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2.2 Table-2(Height of upper)	-	53100	-
5.2.3 Table-2(Seat Region)	-	53100	-
5.3.1.1 Table-2(Construction)	-	53100	-
5.3.1.2 Table-2(Upper/Outsole Bond)	-	53100	-
Table-2(Strength)	-	53100	-
5.3.2.1 Table-2(General)	-	53100	-
5.3.2.2 Table-2(Internal Length of toe cap)	-	53100	-
5.3.2.3 Table-2(Impact Resistance -T- )	-	53100	-
5.3.2.4 Table-2(Compression)	-	53100	-
5.3.2.5 Table-2(Behaviour of toe cap)	-	53100	-
5.3.3 Table-2(Leak Proofness)	-	53100	-
5.3.4 Table-2(Specific Ergonomic)	-	53100	-
Table-2(Features)	-	53100	-
5.3.5.2 Table-2(Slip Resistance SRA)	-	53100	-
5.3.5.3 Table-2(Slip Resistance SRB)	-	53100	-
Table-2(0.18)	-	53100	-
5.3.5.4 Table-2(Slip Resistance SRC)	-	53100	-
5.4.1 Table-2(General)	-	53100	-
5.4.2 Table-2(Thickness)	-	53100	-
5 4 3 Table-2(Tear Strength)	-	53100	-
5.4.4 Table-2(Tensile Properties)	-	53100	-
5.4.5 Table-2(Flexing Resistance)	-	53100	-
5.4.6 Table-2(Water Vapour Permeability & Coefficient)	-	53100	-
5 4.7 Table-2( )	-	53100	-
5 4.8 Table-2(Hydrolysis)	-	53100	-
5.4 9 Table-2(Chrome VI)	-	53100	-
5.5.1 Table-2(Tear Strength)	-	53100	-
5.5.2 Table-2(Abrasion Resistance)	-	53100	-
5.5.3 Table-2(Water Vapour Permeability & Coefficient)	-	53100	-
5.5.4 Table-2(pH Value)	-	53100	-
5.5.5 Table-2(Chrome VI)	-	53100	-
5.7.1 Table-3(Thickness)	-	53100	-
5.7.2 Table-3(pH Value)	-	53100	-
5.7.3 Table-3(Water Absorption &)	-	53100	-
Table-3(Desorption)	-	53100	-
5.7.4.1 Table-3(Insole Abrasion)	-	53100	-
5.7.4.2 Table-3(Abrasion)	-	53100	-
5.7.5 Table-3(Chromium VI)	-	53100	-
5.8.1 Table-2(Design)	-	53100	-
5.8.2 Table-2(Tear Strength)	-	53100	-
5.8.3 Table-3(Abrasion Resistance)	-	53100	-
5.8.4 Table-3(Flexing Resistance)	-	53100	-
5.8.5 Table-3(Hydrolysis)	-	53100	-
5.8.6 Table-2(Interlayer BondStrength)	-	53100	-
6.2.1 Table-I8(Penetration Resistance)	-	53100	-
6.2.2.1 Table-18(Electrical Properties)	-	53100	-
Table-18(Conductive Footwear)	-	53100	-
6.2.2.2 Table-18(Antistatic Footwear)	-	53100	-
6.2.2.3 Table-18(Electrically Insulated)	-	53100	-
6.2.3.1 Table-18(Heat Insulated Comp)	-	53100	-
6.2.3.2 Table-18(Cold Insulated)	-	53100	-
6.2.4 Table-18(Energy Absorption of seat region)	-	53100	-
6.2.5 Table-18(Water Resistance)	-	53100	-
6.2.7 Table-18(Ankle Protection)	-	53100	-
6.2.8 Table-18(Cut Resistance)	-	53100	-
6.3 Table-18(Water Penetration & Absorption)	-	53100	-
6.4.1 Table-18(Resistance to Hot Contact)	-	53100	-
6.4.2 Table-18(Resistance to Fuel oil)	-	53100	-
Cl.4, Table1, Annex A ISO 20344 :2011(Classification and designs)	-	53100	-
Cl. 5,Cl.5.1Table 2, Table 3(General)	-	53100	-
Cl. 5.2, Cl.5.2.1, Figure 3,(General)	-	53100	-
Cl.5.3.5.1, Cl.5.3.5.2,Cl.5.3.5.3 or 5.3.5.4 IS 15298 (Part1):2015,ISO 20344:2011,5.11(General)	-	53100	-
Cl.7, table 2,table 18,table 20, table21, EN 13832-1,EN 13832-3: 2006,6.2.2.3(Electrically insulating footwear)	-	53100	-
8(Information to be supplied)	-	53100	-
Cl.8.1 IS 15298 Part 3:2018, ISO 20346 :2014(General)	-	53100	-
8.2(Electrical properties)	-	53100	-
8.2.1(Conductive footwear)	-	53100	-
8.2.2(Antistatic footwear)	-	53100	-
8.3(Insocks)	-	53100	-
Cl.5.8.1.3(Cleat Height)	-	53100	-
Cl.5.8.1.2(Cleated area)	-	53100	-
Cl.5.8.1.1(Table 17 Thickness)	-	53100	-

Complete

25 Feb, 2027

-
-

136

IS 15298 : Part 2 (2016)

Personal protective equipment: Part 2 safety footwear (Second Revision)

all

53100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4,Table 1(Class I, IS 15298)	-	53100	-
4,Table 1(Class II, IS 15298)	-	53100	-
5.2,5.2.1, Fig 3(Design,General, IS 15298)	-	53100	-
5.2.2, Fig 4(Height of Upper, ISO 20344 , 6.2)	-	53100	-
5.2.3, Table 10 ,Design A(Seat Region)	-	53100	-
5.3.1.1(Construction)	-	53100	-
5.3.1.2(Upper/outer sole bond strength , ISO 20344 , 5.2)	-	53100	-
5.3.2.1(General, EN 12568 OF 4.2.2.2)	-	53100	-
5.3.2.2,Table 5(Internal length of toecaps , ISO 20344 , 5.3)	-	53100	-
5.3.2.3,Table 6(Impact resistance of safety footwear,ISO 20344 , 5.4)	-	53100	-
5.3.2.4 ,Table 6(Compression Resistance of safety footwear ,ISO20344 , 5.5)	-	53100	-
5.3.2.5.1(Corrosion resistance of metallic toecaps ,ISO20344 , 5.6.2)	-	53100	-
5.3.2.5.2(Non metallic toe caps ,EN 12568)	-	53100	-
5.3.3(Leak proofness ,ISO 20344 , 5.7)	-	53100	-
5.3.4(Specific ergonomic feature ,ISO 20344 , 5.1)	-	53100	-
5.3.5.2,Table 7(Slip resistance on ceramic tile floor with sodium lauryl sulphate (NaLS) solution)	-	53100	-
5.3.5.3,Table 8(Slip resistance on steel floor with glycerin)	-	53100	-
5.3.5.4(Slip resistance on ceramic tile floor with NaLS and on steel floor with glycerin)	-	53100	-
5.3.6(Innocuousness)	-	53100	-
5.4.1,Table 10(General)	-	53100	-
5.4.2, Table 11(Thickness , ISO 20344 , 6.1 )	-	53100	-
5.4.3, Table 12(Tear Strength, ISO 20344 , 6.3 )	-	53100	-
5.4.4, Table 13(Tensile properties ,ISO 20344 , 6.4.1 )	-	53100	-
5.4.5, Table 14(Flexing resistance ,ISO 20344,6.5)	-	53100	-
5.4.6(Water vapour permeability and coefficient,ISO 20344,6.6 & 6.8)	-	53100	-
5.4.7(Ph Value ; ISO 20344,6.9)	-	53100	-
5.4.8(Hydrolysis ; ISO 20344,6.10)	-	53100	-
5.4.9(Chromium VI content; ISO 17075)	-	53100	-
5.5.1,Table 15(Tear Strength, ISO 20344 , 6.3)	-	53100	-
5.5.2(Abrasion Resistance ;ISO 20344 , 6.12)	-	53100	-
5.5.3(Water vapour permeability and coefficient,ISO 20344,6.6 & 6.8)	-	53100	-
5.5.4(Ph Value ; ISO 20344,6.9)	-	53100	-
5.5.5(Chromium VI content; ISO 17075)	-	53100	-
5.6(Tongue - IS 15298 Part 2 )	-	53100	-
5.6.1,Table 16(Tear Strength, ISO 20344 , 6.3)	-	53100	-
5.6.2(Ph Value ; ISO 20344,6.9)	-	53100	-
5.6.3(Chromium VI content; ISO 17075)	-	53100	-
5.7.1;Table 3(Thickness ; ISO 20344,7.1)	-	53100	-
5.7.3(Water Absorption and desorption ISO 20344,7.2 )	-	53100	-
5.7.4.1(Insole ; ISO 20344,7.3 )	-	53100	-
5.7.4.2(Insocks ; ISO 20344, 6.12)	-	53100	-
5.7.5(Chromium VI content; ISO 17075)	-	53100	-
5.8.1(Design, IS 15298 Part 2 )	-	53100	-
5.8.1.1, Table 17(Thickness ; ISO 20344, 8.1.2)	-	53100	-
5.8.1.2(Cleated area ; ISO 20344 , Fig 38)	-	53100	-
5.8.1.3, Table 17(Cleat height; ISO 20344, 8.1)	-	53100	-
5.8.2(Tear Strength, ISO 20344 , 8.2)	-	53100	-
5.8.3(Abrasion Resistance ;ISO 20344 , 8.3)	-	53100	-
5.8.4(Flexing resistance ,ISO 20344,8.4)	-	53100	-
5.8.5(Hydrolysis ; ISO 20344,8.5)	-	53100	-
5.8.6(Interlayer bond strength; ISO 20344, 5.2)	-	53100	-
6.2.1.1.1(Metallic anti-penetration insert; ISO 20344, 5.8.2)	-	53100	-
6.2.1.1.2(Non-metallic anti-penetration insert; ISO 20344, 5.8.3)	-	53100	-
6.2.1.2(Consruction)	-	53100	-
6.2.1.3(Dimension ; ISO 20344, 5.8.1)	-	53100	-
6.2.1.4(Flex resistance of penetration -resistant insert ; ISO 20344,5.9)	-	53100	-
6.2.1.5.1(Corrosion resistance of penetration -resistant metallic insert - ISO 20344, 5.6.3 &5.6.1)	-	53100	-
6.2.2.1 (Conductive footwear ; ISO 20344,5.10 & 5.10.3.3)	-	53100	-
6.2.2.2(Antistatic footwear ; ISO 20344,5.10)	-	53100	-
6.2.2.3(Electrically insulating footwear; EN 50321)	-	53100	-
6.2.3.1(Hear insulation of sole complex; ISO 20344,5.12 ;Annex B)	-	53100	-
6.2.3.2(Cold insulation of sole complex; ISO 20344,5.13)	-	53100	-
6.2.4(Energy absorption of seat region; ISO 20344,5.14)	-	53100	-
6.2.5(Water resistance ; 5.15.1 & 5.15.2)	-	53100	-
6.2.6.1(Construction)	-	53100	-
6.2.7 (Ankle protection ; ISO 20344 , 5.17)	-	53100	-
6.2.8.1(Design)	-	53100	-
6.2.8.2(Construction)	-	53100	-
6.2.8.3,EN 388(Resistance to cutting ,EN 388)	-	53100	-
6.2.8.4(Penetration Resistance)	-	53100	-
6.3(Upper--Water penetration and absorption ; ISO 20344 , 5.13)	-	53100	-
6.4.1(Resistance to hot contact ; ISO 20344 , 8.7)	-	53100	-
6.4.2(Resistance to fuel oil ; ISO 20344 , 8.6.1& 8.6.2 ; )	-	53100	-
Cl.5.3.5.1, Cl.5.3.5.2,Cl.5.3.5.3 or 5.3.5.4 IS 15298 (Part1):2015,ISO 20344:2011,5.11(General)	-	53100	-
Cl.7, table 2,table 18,table 20, table21, EN 13832-1,EN 13832-3: 2006,6.2.2.3(Marking)	-	53100	-
8.2(Electrical Properties)	-	53100	-
8.2.2(Antistatic footwear)	-	53100	-
8.3(Insocks)	-	53100	-

Complete

25 Feb, 2027

-
-

137

IS 17953 (2023)

uPVC Profiles for Windows And Doors Specification

52500 View breakup
Complete Test Rs. 52500/-(Exclusive of Resistance to weathering test) Rs. 850000/- for Resistance to Weathering test.

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No.5.1.1(UV Resistant Virgin Material)	-	52500	Complete Test Rs.52500 (exclusive of Resistance to Weathering test) Rs.8,50,000/- for Resistance to weathering test.
Cl. No.5.1.2(Non-UV Resistant Virgin Material)	-	52500	Complete Test Rs.52500 (exclusive of Resistance to Weathering test) Rs.8,50,000/- for Resistance to weathering test.
Cl. No.5.1.3, a), Table no. 1(i)(Monoextrusion or coextrusion of a layer of any visible surface)	-	52500	Complete Test Rs.52500 (exclusive of Resistance to Weathering test) Rs.8,50,000/- for Resistance to weathering test.
Cl. No.5.1.3, a), Table no. 1(ii)("Non-visible surface and material covered by coextrusion")	-	52500	Complete Test Rs.52500 (exclusive of Resistance to Weathering test) Rs.8,50,000/- for Resistance to weathering test.
Cl.No.5.2(Appearance of uPVC Profile)	-	52500	Complete Test Rs.52500 (exclusive of Resistance to Weathering test) Rs.8,50,000/- for Resistance to weathering test.
Cl.No.5.3.1and3.2.5, Table no. 2(i)(Depth (D))	-	52500	Complete Test Rs.52500 (exclusive of Resistance to Weathering test) Rs.8,50,000/- for Resistance to weathering test.
Cl.No.5.3.1and3.2.5, Table no. 2(ii)(Width (W))	-	52500	Complete Test Rs.52500 (exclusive of Resistance to Weathering test) Rs.8,50,000/- for Resistance to weathering test.
Cl.No.5.3.1and3.2.5, Table no. 2(iii)("Sight visible surface wall thickness, Max ")	-	52500	Complete Test Rs.52500 (exclusive of Resistance to Weathering test) Rs.8,50,000/- for Resistance to weathering test.
Cl.No.5.3.1and3.2.5, Table no. 2(iv)("Sight visible surface flatness, Max ")	-	52500	Complete Test Rs.52500 (exclusive of Resistance to Weathering test) Rs.8,50,000/- for Resistance to weathering test.
Cl.No.5.3.1and3.2.5, Table no. 2(v)(Parallelism, Max)	-	52500	Complete Test Rs.52500 (exclusive of Resistance to Weathering test) Rs.8,50,000/- for Resistance to weathering test.
Cl.No.5.3.2(Wall Thickness of Main Profiles)	-	52500	Complete Test Rs.52500 (exclusive of Resistance to Weathering test) Rs.8,50,000/- for Resistance to weathering test.
Cl.No.5.3.3(Tolerances on other Dimensions)	-	52500	Complete Test Rs.52500 (exclusive of Resistance to Weathering test) Rs.8,50,000/- for Resistance to weathering test.
Cl.No.5.3.4(Straightness)	-	52500	Complete Test Rs.52500 (exclusive of Resistance to Weathering test) Rs.8,50,000/- for Resistance to weathering test.
Cl.No.5.4(Mass of Profile)	-	52500	Complete Test Rs.52500 (exclusive of Resistance to Weathering test) Rs.8,50,000/- for Resistance to weathering test.
Cl.No.5.5("Heat Reversion ")	-	52500	Complete Test Rs.52500 (exclusive of Resistance to Weathering test) Rs.8,50,000/- for Resistance to weathering test.
Cl.No.5.6(Resistance to Impact of Falling Mass)	-	52500	Complete Test Rs.52500 (exclusive of Resistance to Weathering test) Rs.8,50,000/- for Resistance to weathering test.
Cl.No.5.7(Heat Ageing)	-	52500	Complete Test Rs.52500 (exclusive of Resistance to Weathering test) Rs.8,50,000/- for Resistance to weathering test.
Cl.No.5.8.1(Tensile Bending Test)	-	52500	Complete Test Rs.52500 (exclusive of Resistance to Weathering test) Rs.8,50,000/- for Resistance to weathering test.
Cl.No.5.8.2(Compression Bending Test)	-	52500	Complete Test Rs.52500 (exclusive of Resistance to Weathering test) Rs.8,50,000/- for Resistance to weathering test.
Cl.No.5.9.(Charpy Impact Resistance of Main Profile)	-	52500	Complete Test Rs.52500 (exclusive of Resistance to Weathering test) Rs.8,50,000/- for Resistance to weathering test.
Cl.No.5.10.(Resistance to Weathering)	-	52500	Complete Test Rs.52500 (exclusive of Resistance to Weathering test) Rs.8,50,000/- for Resistance to weathering test.
Cl.No.5.11(Density)	-	52500	Complete Test Rs.52500 (exclusive of Resistance to Weathering test) Rs.8,50,000/- for Resistance to weathering test.
Cl.No.8(Marking)	-	52500	Complete Test Rs.52500 (exclusive of Resistance to Weathering test) Rs.8,50,000/- for Resistance to weathering test.

Complete

25 Feb, 2027

-
Included w.e.f. 17.07.2023

138

IS 17439 (2020)

Polyphosphoric Acid - Specification

19800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(General requirement)	-	19800	Complete Testing Charges
4.2, Table 1(i) Relative density)	-	19800	Complete Testing Charges
4.2, Table 1(ii) H3PO4)	-	19800	Complete Testing Charges
4.2, Table 1(iii) P2O5)	-	19800	Complete Testing Charges
4.2, Table 1(iv) Fe)	-	19800	Complete Testing Charges
4.2, Table 1(v) Cl)	-	19800	Complete Testing Charges
4.2, Table 1(vii) SO4 ^2-)	-	19800	Complete Testing Charges
4.2, Table 1(viii) As)	-	19800	Complete Testing Charges
4.2, Table 1(ix) Pb)	-	19800	Complete Testing Charges
4.2, Table 1(x) Nitrates)	-	19800	Complete Testing Charges
4.2, Table 1(xi) Antimony)	-	19800	Complete Testing Charges
4.2, Table 1(xii) Manganese)	-	19800	Complete Testing Charges
4.2, Table 1(xiii) Molybedenum)	-	19800	Complete Testing Charges
4.2, Table 1(xiv) Mercury)	-	19800	Complete Testing Charges
4.2, Table 1(xv) Aluminium)	-	19800	Complete Testing Charges
4.2, Table 1(xvi) Calcium and Magnesium)	-	19800	Complete Testing Charges
4.2, Table 1(xvii) Silica as SiO2)	-	19800	Complete Testing Charges
5.1(Packing)	-	19800	Complete Testing Charges
5.2(Marking)	-	19800	Complete Testing Charges

Complete

25 Feb, 2027

-
Included w.e.f. 16.05.2023

139

IS 1110 (2023)

FERROSILICON -- SPECIFICATIONS

All

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1(Constitution of Consignment)	-	9000	-
Clauses 4 and 7.2.1-Table 1(Silicon)	-	9000	-
Clauses 4 and 7.2.1-Table 1(Carbon)	-	9000	-
Clauses 4 and 7.2.1-Table 1(Sulphur)	-	9000	-
Clauses 4 and 7.2.1-Table 1(Phosphorus)	-	9000	-
Clauses 4 and 7.2.1-Table 1(Aluminium)	-	9000	-
Clauses 4 and 7.2.1-Table 1(Calcium)	-	9000	-
Clauses 4 and 7.2.1-Table 1(Manganese)	-	9000	-
Clauses 4 and 7.2.1-Table 1(Boron)	-	9000	-
Clauses 4 and 7.2.1-Table 1(Zirconium)	-	9000	-
Clauses 4 and 7.2.1-Table 1(Titanium)	-	9000	-
8(SIZE)	-	9000	-
9(Extraneous contamination)	-	9000	-

Complete

25 Feb, 2027

-
Included w.e.f. 17.07.2023

140

IS 11996 (1987)

Specification for deltamethrin EC

19000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.1(constituents)	-	19000	Complete Testing Charges
2.2(Physical test)	-	19000	Complete Testing Charges
5.1 Test(Test shall be carried out in accordnace with 2.2.2 to 2.2.5, 2.3.1 and 2.3.2)	-	19000	Complete Testing Charges
5.2 Quality of Reagent(Unless specified otherwise, pure chemicals shall be employed in tests and distilled water ( see IS : 1070-1977t ) shall be used where its use as a reagent is intended)	-	19000	Complete Testing Charges
3.1(Packing)	-	19000	Complete Testing Charges
3.2(Marking)	-	19000	Complete Testing Charges
2.2.1 (Descrtiption)	-	19000	Complete Testing Charges
2.2.2 (Cold Test)	-	19000	Complete Testing Charges
2.2.3 (Flash point (Abel) IS 1448 Part-20:1960)	-	19000	Complete Testing Charges
2.2.4(Emulsion Stability 13.3 of IS :6940-1982)	-	19000	Complete Testing Charges
2.2.5(Heat Stability 13.4 of IS :6940-1982)	-	19000	Complete Testing Charges
2.3.1(Deltamethrin content- Appendix A of IS:12005-1987)	-	19000	Complete Testing Charges
2.3.2(Acidity / Alkalinity - Clause 11.3 & 11.3.1.1 of IS:6940-1982)	-	19000	Complete Testing Charges

Complete

25 Feb, 2027

-
-

141

IS 16240 (2023)

REVERSE OSMOSIS RO BASED POINT-OF-USE POU WATER TREATMENT SYSTEM FOR DRINKING PURPOSES SPECIFICATION first revision

65000 View breakup
Complete testing Rs. 65000/- (Exclusive of Cryptosporidium parvum and Giardia lamblia); Rs. 65000/- for Cryptosporidium parvum and Giardia lamblia.

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.1(Overall migration limits)	-	65000	Complete testing Rs. 65000/- (Exclusive of Cryptosporidium parvum and Giardia lamblia); Rs. 65000/- for Cryptosporidium parvum and Giardia lamblia.
Cl-6.3.1(TDS Reduction)	-	65000	Complete testing Rs. 65000/- (Exclusive of Cryptosporidium parvum and Giardia lamblia); Rs. 65000/- for Cryptosporidium parvum and Giardia lamblia.
Cl-6.3.2.1, 6.3.3.1 and B-1.2,Table 1, sl.no-i(Arsenic)	-	65000	Complete testing Rs. 65000/- (Exclusive of Cryptosporidium parvum and Giardia lamblia); Rs. 65000/- for Cryptosporidium parvum and Giardia lamblia.
Cl-6.3.2.1, 6.3.3.1 and B-1.2,Table 1, sl.no-ii(Cadmium)	-	65000	Complete testing Rs. 65000/- (Exclusive of Cryptosporidium parvum and Giardia lamblia); Rs. 65000/- for Cryptosporidium parvum and Giardia lamblia.
Cl-6.3.2.1, 6.3.3.1 and B-1.2,Table 1, sl.no-iii(Chromium)	-	65000	Complete testing Rs. 65000/- (Exclusive of Cryptosporidium parvum and Giardia lamblia); Rs. 65000/- for Cryptosporidium parvum and Giardia lamblia.
Cl-6.3.2.1, 6.3.3.1 and B-1.2,Table 1, sl.no-iv(Copper)	-	65000	Complete testing Rs. 65000/- (Exclusive of Cryptosporidium parvum and Giardia lamblia); Rs. 65000/- for Cryptosporidium parvum and Giardia lamblia.
Cl-6.3.2.1, 6.3.3.1 and B-1.2,Table 1, sl.no-v(Fluoride)	-	65000	Complete testing Rs. 65000/- (Exclusive of Cryptosporidium parvum and Giardia lamblia); Rs. 65000/- for Cryptosporidium parvum and Giardia lamblia.
Cl-6.3.2.1, 6.3.3.1 and B-1.2,Table 1, sl.no-vi(Lead)	-	65000	Complete testing Rs. 65000/- (Exclusive of Cryptosporidium parvum and Giardia lamblia); Rs. 65000/- for Cryptosporidium parvum and Giardia lamblia.
Cl-6.3.2.1, 6.3.3.1 and B-1.2,Table 1, sl.no-vii(Mercury)	-	65000	Complete testing Rs. 65000/- (Exclusive of Cryptosporidium parvum and Giardia lamblia); Rs. 65000/- for Cryptosporidium parvum and Giardia lamblia.
Cl-6.3.2.1, 6.3.3.1 and B-1.2,Table 1, sl.no-viii(Nitrate)	-	65000	Complete testing Rs. 65000/- (Exclusive of Cryptosporidium parvum and Giardia lamblia); Rs. 65000/- for Cryptosporidium parvum and Giardia lamblia.
Cl-6.3.2.1, 6.3.3.1 and B-1.2,Table 1, sl.no-ix(Pesticides total)	-	65000	Complete testing Rs. 65000/- (Exclusive of Cryptosporidium parvum and Giardia lamblia); Rs. 65000/- for Cryptosporidium parvum and Giardia lamblia.
Cl-6.3.2.1, 6.3.3.1 and B-1.2,Table 1, sl.no-x(E. coli)	-	65000	Complete testing Rs. 65000/- (Exclusive of Cryptosporidium parvum and Giardia lamblia); Rs. 65000/- for Cryptosporidium parvum and Giardia lamblia.
Cl-6.3.2.1, 6.3.3.1 and B-1.2,Table 1, sl.no-xi(MS-2 Coliphage (Virus))	-	65000	Complete testing Rs. 65000/- (Exclusive of Cryptosporidium parvum and Giardia lamblia); Rs. 65000/- for Cryptosporidium parvum and Giardia lamblia.
Cl-6.3.3.2.1,Table 2,sl.no-i(Cryptosporidium parvum)	-	65000	Complete testing Rs. 65000/- (Exclusive of Cryptosporidium parvum and Giardia lamblia); Rs. 65000/- for Cryptosporidium parvum and Giardia lamblia.
Cl-6.3.3.2.1,Table 2,sl.no-ii(Giardia lamblia)	-	65000	Complete testing Rs. 65000/- (Exclusive of Cryptosporidium parvum and Giardia lamblia); Rs. 65000/- for Cryptosporidium parvum and Giardia lamblia.
Cl-6.4(Percent Recovery of Product Water and Hourly Production Rate)	-	65000	Complete testing Rs. 65000/- (Exclusive of Cryptosporidium parvum and Giardia lamblia); Rs. 65000/- for Cryptosporidium parvum and Giardia lamblia.
Cl-6.5.1(Excessive Leakage Current)	-	65000	Complete testing Rs. 65000/- (Exclusive of Cryptosporidium parvum and Giardia lamblia); Rs. 65000/- for Cryptosporidium parvum and Giardia lamblia.
Cl-6.5.2(High Voltage Test)	-	65000	Complete testing Rs. 65000/- (Exclusive of Cryptosporidium parvum and Giardia lamblia); Rs. 65000/- for Cryptosporidium parvum and Giardia lamblia.
Cl-6.5.3(Provision For Earthing)	-	65000	Complete testing Rs. 65000/- (Exclusive of Cryptosporidium parvum and Giardia lamblia); Rs. 65000/- for Cryptosporidium parvum and Giardia lamblia.
Cl-6.6(Power supply)	-	65000	Complete testing Rs. 65000/- (Exclusive of Cryptosporidium parvum and Giardia lamblia); Rs. 65000/- for Cryptosporidium parvum and Giardia lamblia.
Cl-6.7(Pressure Test (Hydrostatic Test) — Type Test)	-	65000	Complete testing Rs. 65000/- (Exclusive of Cryptosporidium parvum and Giardia lamblia); Rs. 65000/- for Cryptosporidium parvum and Giardia lamblia.
Cl-6.8.1(Routine Pressure Test (Pneumatic Test))	-	65000	Complete testing Rs. 65000/- (Exclusive of Cryptosporidium parvum and Giardia lamblia); Rs. 65000/- for Cryptosporidium parvum and Giardia lamblia.
Cl-6.8.2(Full Device Leakage Testing)	-	65000	Complete testing Rs. 65000/- (Exclusive of Cryptosporidium parvum and Giardia lamblia); Rs. 65000/- for Cryptosporidium parvum and Giardia lamblia.

Complete

25 Feb, 2027

-
Included w.e.f. 05.04.2023. Table-1 Sr. No. (x) & (xi) and Table-2 (optional requirement) included w.e.f. 12.07.2023.

142

IS 16202 (2014)

Agro textiles - Woven ground covers for horticulture application - Specification

165000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Linear Density, Denier)	-	165000	-
4.1(Heat Shrinkage, %)	-	165000	-
4.2(Plain Weave & Sett, ends & picks/dm)	-	165000	-
4.3(Colour)	-	165000	-
5.1, Table-1(Mass, g/m² , IS 1964)	-	165000	-
5.1, Table-1(Tensile Test, Kgf, IS 1969,Part-2)	-	165000	-
5.1, Table-1(Tear Strength, Kgf, IS 6489,Part-1)	-	165000	-
5.1, Table-1(Air permeability, cft/ft²/s, IS 11056)	-	165000	-
5.1, Table-1(Index puncture resistance, kgf, Annexure-B)	-	165000	-
5.1, Table-1(UV accelerated exposure testing, Annexure-C)	-	165000	-
5.1, Table-1(Water permeability, lt/m2 /s, IS 14324)	-	165000	-
5.1, Table-1(Water Vapour Permeability, g/m²/day, ISO 11092)	-	165000	-
5.2(Dimension and Mass)	-	165000	-
4.1(Linear Density, Denier)	-	-	-
4.1(Heat Shrinkage, %)	-	-	-
4.2(Plain Weave & Sett, ends & picks/dm)	-	-	-
4.3(Colour)	-	-	-
5.1, Table-1(Mass, g/m² , IS 1964)	-	-	-
5.1, Table-1(Tensile Test, Kgf, IS 1969,Part-2)	-	-	-
5.1, Table-1(Tear Strength, Kgf, IS 6489,Part-1)	-	-	-
5.1, Table-1(Air permeability, cft/ft²/s, IS 11056)	-	-	-
5.1, Table-1(Index puncture resistance, kgf, Annexure-B)	-	-	-
5.1, Table-1(UV accelerated exposure testing, Annexure-C)	-	-	-
5.1, Table-1(Water permeability, lt/m2 /s, IS 14324)	-	-	-
5.1, Table-1(Water Vapour Permeability, g/m²/day, ISO 11092)	-	-	-
5.2(Dimension and Mass)	-	-	-

Complete

25 Feb, 2027

-
Included w.e.f. 23.06.2023. Excluding:- Water permeability, Water Vapour Permeability & Air Permeability

143

IS 17927 : Part 1 (2022)

PLASTICS ETHYLENE-VINYL ACETATE EVA MOULDING AND EXTRUSION MATERIALS PART 1 DESIGNATION SYSTEM AND SPECIFICATIONS

38500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1, Table-1(Vinyl Acetate Content, % IS 13601, ISO 8985)	-	38500	-
6.2, Table-4 & 5(Melt Mass Flow Rate, IS 17927,Part-2)	-	38500	-
6.3.2.1(Pigments and colourants, IS 9833)	-	38500	-
6.3.2.2(Overall migration, mg/dm² IS 9845)	-	38500	-
6.1, Table-1(Vinyl Acetate Content, % IS 13601, ISO 8985)	-	38500	-
6.2, Table-4 & 5(Melt Mass Flow Rate, IS 17927,Part-2)	-	38500	-
6.3.2.1(Pigments and colourants, IS 9833)	-	38500	-
6.3.2.2(Overall migration, mg/dm² IS 9845)	-	38500	-

Complete

25 Feb, 2027

-
Included w.e.f. 23.06.2023

144

IS 3564 (1995)

Hydraulically Regulated Door Closers -Specification

13800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11(Marking)	-	13800	-
12(Packing)	-	13800	-
13(Accessories)	-	13800	-
6(Nominal Sizes)	-	13800	-
8(Essential Requirements)	-	13800	-
9(Finish)	-	13800	-
B-1.2(a) Visual Inspection)	-	13800	-
B-1.3(b) Surface)	-	13800	-
B-1.4(c) Performance Requirements)	-	13800	-
B-1.5(d) Endurance Test)	-	13800	-
Clause 7 (Table 2 - xvii)(Material for Top lid)	-	13800	-
Clause 7 (Table 2 - xvi)(Material for Pawl)	-	13800	-
Clause 7 (Table 2 - xv)(Material for Top nut)	-	13800	-
Clause 7 (Table 2 - xiv)(Material for Main arm bolt)	-	13800	-
Clause 7 (Table 2 - xiii)(Material for Internal bearing and gland )	-	13800	-
Clause 7 (Table 2 - xii)(Material for Material for Eccentric shaft )	-	13800	-
Clause 7 (Table 2 - xi)(Material for Concentric ratchet ( For bottle type ) )	-	13800	-
Clause 7 (Table 2 - x)(Material for Clamp)	-	13800	-
Clause 7 (Table 2 - ix)(Material for Main arm )	-	13800	-
Clause 7 (Table 2 - viii)(Material for Adjusting arm)	-	13800	-
Clause 7 (Table 2 - vii)(Material for All weather resistant homogeneous high viscosity hydraulic)	-	13800	-
Clause 7 (Table 2 - vi)(Material for Control valve screw)	-	13800	-
Clause 7 (Table 2 - v)(Material for Material for Packing/washers)	-	13800	-
Clause 7 (Table 2 - iv)(Material for Piston or Rack-piston/pinion)	-	13800	-
Clause 7 (Table 2 - iii)(Material for Nuts)	-	13800	-
Clause 7 (Table 2 - ii)(Material for Torsion spring helical spring)	-	13800	-

Complete

25 Feb, 2027

-
Included w.e.f. 23.06.2023

145

IS 14756 (2022)

Draft Indian Standard STAINLESS STEEL COOKWARE SPECIFICATION Second Revision of IS 14756

14800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Material)	-	0	-
3.2(Material)	-	0	-
3.3(Material)	-	0	-
3.4(Material)	-	0	-
3.5(Material)	-	0	-
4.1 (Annex A)(Shapes and Dimensions)	-	0	-
4.2 (Table 1)(Shapes and Dimensions)	-	1500	-
4.3(Shapes and Dimensions)	-	0	-
4.4(Shapes and Dimensions)	-	0	-
5.1(Workmanship and Finish)	-	0	-
5.2(Workmanship and Finish)	-	0	-
5.3(Workmanship and Finish)	-	0	-
5.4(Workmanship and Finish)	-	0	-
5.5(Workmanship and Finish)	-	0	-
5.6(Workmanship and Finish)	-	0	-
6.1(Staining Test)	-	0	-
6.2(Mechanical Shock Test (For Cladded Utensils only))	-	0	-
6.4(Dry Heat Test (For Cladded Utensils only))	-	0	-
6.5(Coating Thickness Test (For Copper Deposit))	-	0	-
6.6(3 Ply)	-	0	-
6.7.1(Nominal Capacity Test)	-	0	-
6.8.1(Tests on Tempered Glass Lid)	-	0	-
6.8.2(Tests on Tempered Glass Lid (Ball drop test))	-	0	-
6.8.3(Tests on Tempered Glass Lid (thermal shock test))	-	0	-
6.8.4.1(Tests on Tempered Glass Lid (Free Fall Test with rim facing down))	-	0	-
6.8.4.2(Tests on Tempered Glass Lid (Free Fall Test without rim facing down))	-	0	-
3.1(Material)	-	6500 for entire Cl. 3	-
3.2(Material)	-	-	-
3.3(Material)	-	-	-
3.4(Material)	-	-	-
3.5(Material)	-	-	-
4.1 (Annex A)(Shapes and Dimensions)	-	-	-
4.2 (Table 1)(Shapes and Dimensions)	-	-	-
4.3(Shapes and Dimensions)	-	-	-
4.4(Shapes and Dimensions)	-	-	-
5.1(Workmanship and Finish)	-	1500 for entire Cl. 5	-
5.2(Workmanship and Finish)	-	-	-
5.3(Workmanship and Finish)	-	-	-
5.4(Workmanship and Finish)	-	-	-
5.5(Workmanship and Finish)	-	-	-
5.6(Workmanship and Finish)	-	-	-
6.1(Staining Test)	-	1400	-
6.2(Mechanical Shock Test (For Cladded Utensils only))	-	2500 (Rs. 1500 for Cl. 6.3)	-
6.4(Dry Heat Test (For Cladded Utensils only))	-	2000	-
6.5(Coating Thickness Test (For Copper Deposit))	-	2500	-
6.6(3 Ply)	-	2000	-
6.7.1(Nominal Capacity Test)	-	1000	-
6.8.1(Tests on Tempered Glass Lid)	-	2000	-
6.8.2(Tests on Tempered Glass Lid (Ball drop test))	-	2000	-
6.8.3(Tests on Tempered Glass Lid (thermal shock test))	-	2000	-
6.8.4.1(Tests on Tempered Glass Lid (Free Fall Test with rim facing down))	-	1200	-
6.8.4.2(Tests on Tempered Glass Lid (Free Fall Test without rim facing down))	-	1200	-

Complete

25 Feb, 2027

-
Included w.e.f. 23.06.2023

146

IS 8931 (2021)

Copper alloy single taps, combination tap assemblies, stop valves and single lever mixers for water services Specification (second revision)

42000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4(Classfication)	-	42000	-
Cl 6.1(Manufacture,Workmanship & Construction)	-	42000	-
Cl 6.5(Manufacture,Workmanship & Construction)	-	42000	-
Cl 6.6(Manufacture,Workmanship & Construction)	-	42000	-
Cl 6.7(Manufacture,Workmanship & Construction)	-	42000	-
Cl 6.8(Manufacture,Workmanship & Construction)	-	42000	-
Cl 6.9(Manufacture,Workmanship & Construction)	-	42000	-
Cl 6.10(Manufacture,Workmanship & Construction)	-	42000	-
Cl 6.11(Manufacture,Workmanship & Construction)	-	42000	-
Cl 6.12(Manufacture,Workmanship & Construction)	-	42000	-
Cl 6.13(Manufacture,Workmanship & Construction)	-	42000	-
Cl 7(DIMENSIONS)	-	42000	-
Cl 8(ADDITIONAL REQUIREMENTS FOR ACCESSIBLE TAPS)	-	42000	-
Cl 10(PERFORMANCE REQUIREMENTS)	-	42000	-
Cl 11(ADDITIONAL REQUIREMENTS FOR WATER EFFICIENCY)	-	42000	-
As per Table-1(Carbon)	-	42000	-
As per Table-1(Sulphur)	-	42000	-
As per Table-1(Phosphorus)	-	42000	-
As per Table-1(Manganese)	-	42000	-
As per Table-1(Nitrogen)	-	42000	-
As per Table-1(Silicon)	-	42000	-
As per Table-1(Aluminium)	-	42000	-
As per Table-1(Chromium)	-	42000	-
As per Table-1(Vanadium)	-	42000	-
As per Table-1(Molybdenum)	-	42000	-
As per Table-1(Iron)	-	42000	-
As per Table-1(Nickel)	-	42000	-
As per Table-1(Copper)	-	42000	-
As per Table-1(Zinc)	-	42000	-
As per Table-1(Lead)	-	42000	-
As per Table-1(Boron)	-	42000	-
Cl 4(Classfication)	-	42000	-
Cl 6.1(Manufacture,Workmanship & Construction)	-	42000	-
Cl 6.5(Manufacture,Workmanship & Construction)	-	42000	-
Cl 6.6(Manufacture,Workmanship & Construction)	-	42000	-
Cl 6.7(Manufacture,Workmanship & Construction)	-	42000	-
Cl 6.8(Manufacture,Workmanship & Construction)	-	42000	-
Cl 6.9(Manufacture,Workmanship & Construction)	-	42000	-
Cl 6.10(Manufacture,Workmanship & Construction)	-	42000	-
Cl 6.11(Manufacture,Workmanship & Construction)	-	42000	-
Cl 6.12(Manufacture,Workmanship & Construction)	-	42000	-
Cl 6.13(Manufacture,Workmanship & Construction)	-	42000	-
Cl 7(DIMENSIONS)	-	42000	-
Cl 8(ADDITIONAL REQUIREMENTS FOR ACCESSIBLE TAPS)	-	42000	-
Cl 10(PERFORMANCE REQUIREMENTS)	-	42000	-
Cl 11(ADDITIONAL REQUIREMENTS FOR WATER EFFICIENCY)	-	42000	-
As per Table-1(Carbon)	-	42000	-
As per Table-1(Sulphur)	-	42000	-
As per Table-1(Phosphorus)	-	42000	-
As per Table-1(Manganese)	-	42000	-
As per Table-1(Nitrogen)	-	42000	-
As per Table-1(Silicon)	-	42000	-
As per Table-1(Aluminium)	-	42000	-
As per Table-1(Chromium)	-	42000	-
As per Table-1(Vanadium)	-	42000	-
As per Table-1(Molybdenum)	-	42000	-
As per Table-1(Iron)	-	42000	-
As per Table-1(Nickel)	-	42000	-
As per Table-1(Copper)	-	42000	-
As per Table-1(Zinc)	-	42000	-
As per Table-1(Lead)	-	42000	-
As per Table-1(Boron)	-	42000	-
Cl 4(Classfication)	-	-	-
Cl 6.1(Manufacture,Workmanship & Construction)	-	-	-
Cl 6.5(Manufacture,Workmanship & Construction)	-	-	-
Cl 6.6(Manufacture,Workmanship & Construction)	-	-	-
Cl 6.7(Manufacture,Workmanship & Construction)	-	-	-
Cl 6.8(Manufacture,Workmanship & Construction)	-	-	-
Cl 6.9(Manufacture,Workmanship & Construction)	-	-	-
Cl 6.10(Manufacture,Workmanship & Construction)	-	-	-
Cl 6.11(Manufacture,Workmanship & Construction)	-	-	-
Cl 6.12(Manufacture,Workmanship & Construction)	-	-	-
Cl 6.13(Manufacture,Workmanship & Construction)	-	-	-
Cl 7(DIMENSIONS)	-	-	-
Cl 8(ADDITIONAL REQUIREMENTS FOR ACCESSIBLE TAPS)	-	-	-
Cl 10(PERFORMANCE REQUIREMENTS)	-	-	-
Cl 11(ADDITIONAL REQUIREMENTS FOR WATER EFFICIENCY)	-	-	-
As per Table-1(Carbon)	-	-	-
As per Table-1(Sulphur)	-	-	-
As per Table-1(Phosphorus)	-	-	-
As per Table-1(Manganese)	-	-	-
As per Table-1(Nitrogen)	-	-	-
As per Table-1(Silicon)	-	-	-
As per Table-1(Aluminium)	-	-	-
As per Table-1(Chromium)	-	-	-
As per Table-1(Vanadium)	-	-	-
As per Table-1(Molybdenum)	-	-	-
As per Table-1(Iron)	-	-	-
As per Table-1(Nickel)	-	-	-
As per Table-1(Copper)	-	-	-
As per Table-1(Zinc)	-	-	-
As per Table-1(Lead)	-	-	-
As per Table-1(Boron)	-	-	-

Complete

25 Feb, 2027

-
Included w.e.f. 23.06.2023

147

IS 781 (1984)

Specification for cast copper alloy screw down bib taps and stop valves for water services (Third Revision)

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4.1, Table-1(Csat Brass LCB-1 of IS 292 1983,Ingots, Cu + Ni)	-	6000	-
Clause 4.1, Table-1(Cast Brass LCB-1 of IS 292 1983,Ingots, Pb)	-	6000	-
Clause 4.1, Table-1(Cast Brass LCB-1 of IS 292 1983,Ingots, Sn)	-	6000	-
Clause 4.1, Table-1(Cast Brass LCB-1 of IS 292 1983,Ingots, Fe)	-	6000	-
Clause 4.1, Table-1(Cast Brass LCB-1 of IS 292 1983,Ingots, Al)	-	6000	-
Clause 4.1, Table-1(Cast Brass LCB-1 of IS 292 1983,Ingots, Zn)	-	6000	-
Clause 4.1, Table-1(Cast Brass LCB-2 of IS 292 1983,Ingots, Cu + Ni)	-	6000	-
Clause 4.1, Table-1( Cast Brass LCB-1 of IS 292 1983,Castings, Pb)	-	6000	-
Clause 4.1, Table-1(Cast Brass LCB-1 of IS 292 1983,Castings, Sn)	-	6000	-
Clause 4.1, Table-1(Cast Brass LCB-1 of IS 292 1983,Castings, Fe)	-	6000	-
Clause 4.1, Table-1(Cast Brass LCB-1 of IS 292 1983,Castings, Al)	-	6000	-
Clause 4.1, Table-1(Cast Brass LCB-1 of IS 292 1983,Castings, Zn)	-	6000	-
Clause 4.1, Table-1(Cast Brass LCB-2 of IS 292 1983,Ingots, Pb)	-	6000	-
Clause 4.1, Table-1(Cast Brass LCB-2 of IS 292 1983,Ingots, Sn)	-	6000	-
Clause 4.1, Table-1(Cast Brass LCB-2 of IS 292 1983,Ingots, Fe)	-	6000	-
Clause 4.1, Table-1(Cast Brass LCB-2 of IS 292 1983,Ingots, Al)	-	6000	-
Clause 4.1, Table-1(Cast Brass LCB-2 of IS 292 1983,Ingots, Zn)	-	6000	-
Clause 4.1, Table-1(Cast Brass LCB-2 of IS 292 1983,Casting, Cu + Ni)	-	6000	-
Clause 4.1, Table-1(Cast Brass LCB-2 of IS 292 1983,Castings, Pb)	-	6000	-
Clause 4.1, Table-1(Cast Brass LCB-2 of IS 292 1983,Castings, Sn)	-	6000	-
Clause 4.1, Table-1(Cast Brass LCB-2 of IS 292 1983, Castings, Fe)	-	6000	-
Clause 4.1, Table-1(Cast Brass LCB-2 of IS 292 1983,Casting, Al)	-	6000	-
Clause 4.1, Table-1(Cast Brass LCB-2 of IS 292 1983,Casting, Zn)	-	6000	-
Clause 4.1, Table-1(Cast Brass Grade DCB - 2 of IS 1264 : 1981, Die Casting, Cu)	-	6000	-
Clause 4.1, Table-1(Cast Brass Grade DCB - 2 of IS 1264 : 1981, Die Casting, Sn)	-	6000	-
Clause 4.1, Table-1(Cast Brass Grade DCB - 2 of IS 1264 : 1981, Die Casting, Pb)	-	6000	-
Clause 4.1, Table-1(Cast Brass Grade DCB - 2 of IS 1264 : 1981, Die Casting, Ni)	-	6000	-
Clause 4.1, Table-1(Cast Brass Grade DCB - 2 of IS 1264 : 1981, Die Casting, Fe)	-	6000	-
Clause 4.1, Table-1(Cast Brass Grade DCB - 2 of IS 1264 : 1981, Die Casting, Mn)	-	6000	-
Clause 4.1, Table-1(Cast Brass Grade DCB - 2 of IS 1264 : 1981, Die Casting, Si)	-	6000	-
Clause 4.1, Table-1(Cast Brass Grade DCB - 2 of IS 1264 : 1981, Die Casting, Total imporities (excludig Ni + Pb + Al))	-	6000	-
Clause 4.1, Table-1(Cast Brass Grade DCB - 2 of IS 1264 : 1981, Die Casting, Zn)	-	6000	-
Clause 4.1, Table-1(Leaded In Tin Bronze ,LTB-2 of IS 318, Sn)	-	6000	-
Clause 4.1, Table-1(Leaded In Tin Bronze ,LTB-2 of IS 318, Zn)	-	6000	-
Clause 4.1, Table-1(Leaded In Tin Bronze ,LTB-2 of IS 318, Pb)	-	6000	-
Clause 4.1, Table-1(Leaded In Tin Bronze ,LTB-2 of IS 318, Ni)	-	6000	-
Clause 4.1, Table-1(Leaded In Tin Bronze ,LTB-2 of IS 318, Al)	-	6000	-
Clause 4.1, Table-1(Leaded In Tin Bronze ,LTB-2 of IS 318, Si)	-	6000	-
Clause 4.1, Table-1(Leaded In Tin Bronze ,LTB-2 of IS 318, Sb)	-	6000	-
Clause 4.1, Table-1(Leaded In Tin Bronze ,LTB-2 of IS 318, Fe)	-	6000	-
Clause 4.1, Table-1(Leaded In Tin Bronze ,LTB-2 of IS 318, Total of All imporities )	-	6000	-
Clause 4.1, Table-1(Leaded In Tin Bronze ,LTB-2 of IS 318, Cu)	-	6000	-
Clause 4.1, Table-1(Brass, Tyape 1 half Hard of IS 319 : 2007, Grade -1 , Cu)	-	6000	-
Clause 4.1, Table-1(Brass, Tyape 1 half Hard of IS 319 : 2007, Grade -1 , Pb)	-	6000	-
Clause 4.1, Table-1(Brass, Tyape 1 half Hard of IS 319 : 2007, Grade -1 , Fe)	-	6000	-
Clause 4.1, Table-1(Brass, Tyape 1 half Hard of IS 319 : 2007, Grade -1 , Total Other impurities( Excluding Fe))	-	6000	-
Clause 4.1, Table-1(Brass, Tyape 1 half Hard of IS 319 : 2007, Grade -1 , Zn)	-	6000	-
Clause 4.1, Table-1(Brass, Tyape 1 half Hard of IS 319 : 2007, Grade -2 , Cu)	-	6000	-
Clause 4.1, Table-1(Brass, Tyape 1 half Hard of IS 319 : 2007, Grade -2, Pb)	-	6000	-
Clause 4.1, Table-1(Brass, Tyape 1 half Hard of IS 319 : 2007, Grade -2 , Fe)	-	6000	-
Clause 4.1, Table-1(Brass, Tyape 1 half Hard of IS 319 : 2007, Grade -12, Total Other impurities( Excluding Fe))	-	6000	-
Clause 4.1, Table-1(Brass, Tyape 1 half Hard of IS 319 : 2007, Grade -2 , Zn)	-	6000	-
Clause 4.1, Table-1(Grade HT 1 of IS 320 : 1980, Copper + incidental Nickel)	-	6000	-
Clause 4.1, Table-1(Grade HT 1 of IS 320 : 1980, Sn)	-	6000	-
Clause 4.1, Table-1(Grade HT 1 of IS 320 : 1980, Pb)	-	6000	-
Clause 4.1, Table-1(Grade HT 1 of IS 320 : 1980, Fe)	-	6000	-
Clause 4.1, Table-1(Grade HT 1 of IS 320 : 1980, Mn)	-	6000	-
Clause 4.1, Table-1(Grade HT 1 of IS 320 : 1980, Al)	-	6000	-
Clause 4.1, Table-1(Grade HT 1 of IS 320 : 1980, Sb)	-	6000	-
Clause 4.1, Table-1(Grade HT 1 of IS 320 : 1980, Total other elements )	-	6000	-
Clause 4.1, Table-1(Grade HT 1 of IS 320 : 1980, Zn)	-	6000	-
Clause 4.1, Table-1(Grade FHTB 1 of IS 6912 : 2005, Cu)	-	6000	-
Clause 4.1, Table-1(Grade FHTB 1 of IS 6912 : 2005, Pb)	-	6000	-
Clause 4.1, Table-1(Grade FHTB 1 of IS 6912 : 2005, Sn)	-	6000	-
Clause 4.1, Table-1(Grade FHTB 1 of IS 6912 : 2005, Fe)	-	6000	-
Clause 4.1, Table-1(Grade FHTB 1 of IS 6912 : 2005, Al)	-	6000	-
Clause 4.1, Table-1(Grade FHTB 1 of IS 6912 : 2005, Mn)	-	6000	-
Clause 4.1, Table-1(Grade FHTB 1 of IS 6912 : 2005, Zn)	-	6000	-
Cl 3(Nominal Size)	-	6000	-
Cl 4.1(Materials)	-	6000	-
Cl 5(Dimensions & Tolerances)	-	6000	-
Cl 6.1(CONSTRUCTION AND WORKMANSHIP)	-	6000	-
Cl 6.3(CONSTRUCTION AND WORKMANSHIP)	-	6000	-
Cl 6.4(CONSTRUCTION AND WORKMANSHIP)	-	6000	-
Cl 6.5(CONSTRUCTION AND WORKMANSHIP)	-	6000	-
Cl 6.6(CONSTRUCTION AND WORKMANSHIP)	-	6000	-
Cl 6.7(CONSTRUCTION AND WORKMANSHIP)	-	6000	-
Cl 6.8(CONSTRUCTION AND WORKMANSHIP)	-	6000	-
Cl 6.11(CONSTRUCTION AND WORKMANSHIP)	-	6000	-
Cl 7(MINIMUM MASS)	-	6000	-
Cl 8(Finish)	-	6000	-
Cl 9(Testing)	-	6000	-
Clause 4.1, Table-1(Csat Brass LCB-1 of IS 292 1983,Ingots, Cu + Ni)	-	-	-
Clause 4.1, Table-1(Cast Brass LCB-1 of IS 292 1983,Ingots, Pb)	-	-	-
Clause 4.1, Table-1(Cast Brass LCB-1 of IS 292 1983,Ingots, Sn)	-	-	-
Clause 4.1, Table-1(Cast Brass LCB-1 of IS 292 1983,Ingots, Fe)	-	-	-
Clause 4.1, Table-1(Cast Brass LCB-1 of IS 292 1983,Ingots, Al)	-	-	-
Clause 4.1, Table-1(Cast Brass LCB-1 of IS 292 1983,Ingots, Zn)	-	-	-
Clause 4.1, Table-1(Cast Brass LCB-2 of IS 292 1983,Ingots, Cu + Ni)	-	-	-
Clause 4.1, Table-1( Cast Brass LCB-1 of IS 292 1983,Castings, Pb)	-	-	-
Clause 4.1, Table-1(Cast Brass LCB-1 of IS 292 1983,Castings, Sn)	-	-	-
Clause 4.1, Table-1(Cast Brass LCB-1 of IS 292 1983,Castings, Fe)	-	-	-
Clause 4.1, Table-1(Cast Brass LCB-1 of IS 292 1983,Castings, Al)	-	-	-
Clause 4.1, Table-1(Cast Brass LCB-1 of IS 292 1983,Castings, Zn)	-	-	-
Clause 4.1, Table-1(Cast Brass LCB-2 of IS 292 1983,Ingots, Pb)	-	-	-
Clause 4.1, Table-1(Cast Brass LCB-2 of IS 292 1983,Ingots, Sn)	-	-	-
Clause 4.1, Table-1(Cast Brass LCB-2 of IS 292 1983,Ingots, Fe)	-	-	-
Clause 4.1, Table-1(Cast Brass LCB-2 of IS 292 1983,Ingots, Al)	-	-	-
Clause 4.1, Table-1(Cast Brass LCB-2 of IS 292 1983,Ingots, Zn)	-	-	-
Clause 4.1, Table-1(Cast Brass LCB-2 of IS 292 1983,Casting, Cu + Ni)	-	-	-
Clause 4.1, Table-1(Cast Brass LCB-2 of IS 292 1983,Castings, Pb)	-	-	-
Clause 4.1, Table-1(Cast Brass LCB-2 of IS 292 1983,Castings, Sn)	-	-	-
Clause 4.1, Table-1(Cast Brass LCB-2 of IS 292 1983, Castings, Fe)	-	-	-
Clause 4.1, Table-1(Cast Brass LCB-2 of IS 292 1983,Casting, Al)	-	-	-
Clause 4.1, Table-1(Cast Brass LCB-2 of IS 292 1983,Casting, Zn)	-	-	-
Clause 4.1, Table-1(Cast Brass Grade DCB - 2 of IS 1264 : 1981, Die Casting, Cu)	-	-	-
Clause 4.1, Table-1(Cast Brass Grade DCB - 2 of IS 1264 : 1981, Die Casting, Sn)	-	-	-
Clause 4.1, Table-1(Cast Brass Grade DCB - 2 of IS 1264 : 1981, Die Casting, Pb)	-	-	-
Clause 4.1, Table-1(Cast Brass Grade DCB - 2 of IS 1264 : 1981, Die Casting, Ni)	-	-	-
Clause 4.1, Table-1(Cast Brass Grade DCB - 2 of IS 1264 : 1981, Die Casting, Fe)	-	-	-
Clause 4.1, Table-1(Cast Brass Grade DCB - 2 of IS 1264 : 1981, Die Casting, Mn)	-	-	-
Clause 4.1, Table-1(Cast Brass Grade DCB - 2 of IS 1264 : 1981, Die Casting, Si)	-	-	-
Clause 4.1, Table-1(Cast Brass Grade DCB - 2 of IS 1264 : 1981, Die Casting, Total imporities (excludig Ni + Pb + Al))	-	-	-
Clause 4.1, Table-1(Cast Brass Grade DCB - 2 of IS 1264 : 1981, Die Casting, Zn)	-	-	-
Clause 4.1, Table-1(Leaded In Tin Bronze ,LTB-2 of IS 318, Sn)	-	-	-
Clause 4.1, Table-1(Leaded In Tin Bronze ,LTB-2 of IS 318, Zn)	-	-	-
Clause 4.1, Table-1(Leaded In Tin Bronze ,LTB-2 of IS 318, Pb)	-	-	-
Clause 4.1, Table-1(Leaded In Tin Bronze ,LTB-2 of IS 318, Ni)	-	-	-
Clause 4.1, Table-1(Leaded In Tin Bronze ,LTB-2 of IS 318, Al)	-	-	-
Clause 4.1, Table-1(Leaded In Tin Bronze ,LTB-2 of IS 318, Si)	-	-	-
Clause 4.1, Table-1(Leaded In Tin Bronze ,LTB-2 of IS 318, Sb)	-	-	-
Clause 4.1, Table-1(Leaded In Tin Bronze ,LTB-2 of IS 318, Fe)	-	-	-
Clause 4.1, Table-1(Leaded In Tin Bronze ,LTB-2 of IS 318, Total of All imporities )	-	-	-
Clause 4.1, Table-1(Leaded In Tin Bronze ,LTB-2 of IS 318, Cu)	-	-	-
Clause 4.1, Table-1(Brass, Tyape 1 half Hard of IS 319 : 2007, Grade -1 , Cu)	-	-	-
Clause 4.1, Table-1(Brass, Tyape 1 half Hard of IS 319 : 2007, Grade -1 , Pb)	-	-	-
Clause 4.1, Table-1(Brass, Tyape 1 half Hard of IS 319 : 2007, Grade -1 , Fe)	-	-	-
Clause 4.1, Table-1(Brass, Tyape 1 half Hard of IS 319 : 2007, Grade -1 , Total Other impurities( Excluding Fe))	-	-	-
Clause 4.1, Table-1(Brass, Tyape 1 half Hard of IS 319 : 2007, Grade -1 , Zn)	-	-	-
Clause 4.1, Table-1(Brass, Tyape 1 half Hard of IS 319 : 2007, Grade -2 , Cu)	-	-	-
Clause 4.1, Table-1(Brass, Tyape 1 half Hard of IS 319 : 2007, Grade -2, Pb)	-	-	-
Clause 4.1, Table-1(Brass, Tyape 1 half Hard of IS 319 : 2007, Grade -2 , Fe)	-	-	-
Clause 4.1, Table-1(Brass, Tyape 1 half Hard of IS 319 : 2007, Grade -12, Total Other impurities( Excluding Fe))	-	-	-
Clause 4.1, Table-1(Brass, Tyape 1 half Hard of IS 319 : 2007, Grade -2 , Zn)	-	-	-
Clause 4.1, Table-1(Grade HT 1 of IS 320 : 1980, Copper + incidental Nickel)	-	-	-
Clause 4.1, Table-1(Grade HT 1 of IS 320 : 1980, Sn)	-	-	-
Clause 4.1, Table-1(Grade HT 1 of IS 320 : 1980, Pb)	-	-	-
Clause 4.1, Table-1(Grade HT 1 of IS 320 : 1980, Fe)	-	-	-
Clause 4.1, Table-1(Grade HT 1 of IS 320 : 1980, Mn)	-	-	-
Clause 4.1, Table-1(Grade HT 1 of IS 320 : 1980, Al)	-	-	-
Clause 4.1, Table-1(Grade HT 1 of IS 320 : 1980, Sb)	-	-	-
Clause 4.1, Table-1(Grade HT 1 of IS 320 : 1980, Total other elements )	-	-	-
Clause 4.1, Table-1(Grade HT 1 of IS 320 : 1980, Zn)	-	-	-
Clause 4.1, Table-1(Grade FHTB 1 of IS 6912 : 2005, Cu)	-	-	-
Clause 4.1, Table-1(Grade FHTB 1 of IS 6912 : 2005, Pb)	-	-	-
Clause 4.1, Table-1(Grade FHTB 1 of IS 6912 : 2005, Sn)	-	-	-
Clause 4.1, Table-1(Grade FHTB 1 of IS 6912 : 2005, Fe)	-	-	-
Clause 4.1, Table-1(Grade FHTB 1 of IS 6912 : 2005, Al)	-	-	-
Clause 4.1, Table-1(Grade FHTB 1 of IS 6912 : 2005, Mn)	-	-	-
Clause 4.1, Table-1(Grade FHTB 1 of IS 6912 : 2005, Zn)	-	-	-
Cl 3(Nominal Size)	-	-	-
Cl 4.1(Materials)	-	-	-
Cl 5(Dimensions & Tolerances)	-	-	-
Cl 6.1(CONSTRUCTION AND WORKMANSHIP)	-	-	-
Cl 6.3(CONSTRUCTION AND WORKMANSHIP)	-	-	-
Cl 6.4(CONSTRUCTION AND WORKMANSHIP)	-	-	-
Cl 6.5(CONSTRUCTION AND WORKMANSHIP)	-	-	-
Cl 6.6(CONSTRUCTION AND WORKMANSHIP)	-	-	-
Cl 6.7(CONSTRUCTION AND WORKMANSHIP)	-	-	-
Cl 6.8(CONSTRUCTION AND WORKMANSHIP)	-	-	-
Cl 6.11(CONSTRUCTION AND WORKMANSHIP)	-	-	-
Cl 7(MINIMUM MASS)	-	-	-
Cl 8(Finish)	-	-	-
Cl 9(Testing)	-	-	-

Complete

25 Feb, 2027

-
Included w.e.f. 23.06.2023

148

IS 278 (2009)

Galvanized steel barbed wire for fencing - Specification (Fourth Revision)

4500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Type A/Type B)	-	4500	-
5 Table-1(Sizes Diameter of Line wire)	-	4500	-
5 Table-1(Sizes Diamater of Point wire)	-	4500	-
5 Table-1(Sizes Mass of Completed barbed wire)	-	4500	-
5 Table-1(Sizes Distance between two barbs)	-	4500	-
5 Table-1(Sizes No. of Lays between the two consequtive barbs)	-	4500	-
7.1(Manufacture)	-	4500	-
7.2(Manufacture)	-	4500	-
7.2(Manufacture)	-	4500	-
7.3(Manufacture)	-	4500	-
8(CHROMATING)	-	4500	-
9.1(Freedom from defects)	-	4500	-
9.2(Freedom from defects)	-	4500	-
12.1(Tensile Strength)	-	4500	-
12.1(Breaking load)	-	4500	-
12.2.1(Mass of zinc coating (line wire))	-	4500	-
12.2.2(Mass of zinc coating (point wire))	-	4500	-
12.2(Uniformity of zinc coating)	-	4500	-
12.3(Ductility)	-	4500	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	4500	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	4500	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	4500	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	4500	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	4500	-
Cl. 7.2(Cut Angle)	-	4500	-
Cl. 7.2(Length of Barbs)	-	4500	-
Cl. 7.2(Finishing of Barbs)	-	4500	-
Cl. 7.1(General)	-	4500	-
11(Sampling)	-	4500	-
13(Marking)	-	4500	-
4(Type A/Type B)	-	-	-
5 Table-1(Sizes Diameter of Line wire)	-	-	-
5 Table-1(Sizes Diamater of Point wire)	-	-	-
5 Table-1(Sizes Mass of Completed barbed wire)	-	-	-
5 Table-1(Sizes Distance between two barbs)	-	-	-
5 Table-1(Sizes No. of Lays between the two consequtive barbs)	-	-	-
7.1(Manufacture)	-	-	-
7.2(Manufacture)	-	-	-
7.2(Manufacture)	-	-	-
7.3(Manufacture)	-	-	-
8(CHROMATING)	-	-	-
9.1(Freedom from defects)	-	-	-
9.2(Freedom from defects)	-	-	-
12.1(Tensile Strength)	-	-	-
12.1(Breaking load)	-	-	-
12.2.1(Mass of zinc coating (line wire))	-	-	-
12.2.2(Mass of zinc coating (point wire))	-	-	-
12.2(Uniformity of zinc coating)	-	-	-
12.3(Ductility)	-	-	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	-	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	-	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	-	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	-	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	-	-
Cl. 7.2(Cut Angle)	-	-	-
Cl. 7.2(Length of Barbs)	-	-	-
Cl. 7.2(Finishing of Barbs)	-	-	-
Cl. 7.1(General)	-	-	-
11(Sampling)	-	-	-
13(Marking)	-	-	-

Complete

25 Feb, 2027

-
Included w.e.f. 23.06.2023

149

IS 2266 (2019)

Steel wire ropes for general engineering purpose - Specification (Fifth Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 8.2(Grade-1, Table-1, IS 1835:1976, Carbon)	-	15000	-
Clause 8.2(Manganese)	-	15000	-
Clause 8.2(Silicon)	-	15000	-
Clause 8.2(Sulphur)	-	15000	-
Clause 8.2(Phosphorus)	-	15000	-
Clause 8.2(Copper)	-	15000	-
Clause 8.2(Nickel)	-	15000	-
Clause 8.2(Chromium)	-	15000	-
Clause 8.2(Phosphorus+ Sulphur)	-	15000	-
Clause 8.2(Grade-2, Table-1, IS 1835:1976, Carbon)	-	15000	-
Clause 8.2(Grade-3, Table-1, IS 1835:1976, Carbon)	-	15000	-
Clause 8.2(Grade-4, Table-1, IS 1835:1976, Carbon)	-	15000	-
12(a) Size)	-	15000	-
12(b) Construction)	-	15000	-
12(c) Rope Grade)	-	15000	-
12(d) lay)	-	15000	-
12(e) Core coating)	-	15000	-
12(f) length of wire rope)	-	15000	-
12(g) Reel/coil number along with the order number)	-	15000	-
12(h) BIS Standards Mark)	-	15000	-
4(Rope Size and Tolerance )	-	15000	-
5(Minimum Breaking Force)	-	15000	-
6(General Requirements)	-	15000	-
7(Construction)	-	15000	-
8(a) Fibre Core)	-	15000	-
8(b) Steel Core)	-	15000	-
9(Joints)	-	15000	-
10(Galvanizing)	-	15000	-
6.1(Water soluble acids)	-	15000	-
6.2(Salts)	-	15000	-
Clause 6 of IS 2266, Table 1-13 IS 2266, IS 6594 Clause 6.5(Mass)	-	15000	-
Clause 10(Mass of Zinc Coating)	-	15000	-
Clause 10(Uniformity of Coating)	-	15000	-
Clause 6 of IS 2266, IS 6594 Clause 5.2(Ovality)	-	15000	-
Clause 6 of IS 2266, IS 6594 Clause 6.4(Length)	-	15000	-
Clause 6 of IS 2266, IS 6594 Clause 7(Freedom from defect)	-	15000	-
Clause 6 of IS 2266, IS 6594 Clause 10.3.3(Torsion Test)	-	15000	-
Clause 6 of IS 2266, IS 6594 Clause 10.3.4(Reverse Bend)	-	15000	-
Clause 6 of IS 2266, IS 6594 Clause 6.7.1(Length of Lay)	-	15000	-
Clause 6 of IS 2266, IS 6594 Clause 6.7.2(Direction of Lay)	-	15000	-
Clause 6 of IS 2266, IS 6594 Clause 10.3.1.1(Tensile Test (Individual Wire))	-	15000	-
Clause 6 of IS 2266, IS 6594 Clause 10.3.1.1(Torsion Test (Indiviual Wire))	-	15000	-
Clause 6 of IS 2266, IS 6594 Clause 10.3.1.1(Reverse Bend test (Individual Wire))	-	15000	-
Clause 6 of IS 2266, IS 6594 Clause 10.3.6(Diameter of Wire)	-	15000	-
Clause 8.2(Grade-1, Table-1, IS 1835:1976, Carbon)	-	15000	-
Clause 8.2(Manganese)	-	15000	-
Clause 8.2(Silicon)	-	15000	-
Clause 8.2(Sulphur)	-	15000	-
Clause 8.2(Phosphorus)	-	15000	-
Clause 8.2(Copper)	-	15000	-
Clause 8.2(Nickel)	-	15000	-
Clause 8.2(Chromium)	-	15000	-
Clause 8.2(Phosphorus+ Sulphur)	-	15000	-
Clause 8.2(Grade-2, Table-1, IS 1835:1976, Carbon)	-	15000	-
Clause 8.2(Grade-3, Table-1, IS 1835:1976, Carbon)	-	15000	-
Clause 8.2(Grade-4, Table-1, IS 1835:1976, Carbon)	-	15000	-
12(a) Size)	-	15000	-
12(b) Construction)	-	15000	-
12(c) Rope Grade)	-	15000	-
12(d) lay)	-	15000	-
12(e) Core coating)	-	15000	-
12(f) length of wire rope)	-	15000	-
12(g) Reel/coil number along with the order number)	-	15000	-
12(h) BIS Standards Mark)	-	15000	-
4(Rope Size and Tolerance )	-	15000	-
5(Minimum Breaking Force)	-	15000	-
6(General Requirements)	-	15000	-
7(Construction)	-	15000	-
8(a) Fibre Core)	-	15000	-
8(b) Steel Core)	-	15000	-
9(Joints)	-	15000	-
10(Galvanizing)	-	15000	-
6.1(Water soluble acids)	-	15000	-
6.2(Salts)	-	15000	-
Clause 6 of IS 2266, Table 1-13 IS 2266, IS 6594 Clause 6.5(Mass)	-	15000	-
Clause 10(Mass of Zinc Coating)	-	15000	-
Clause 10(Uniformity of Coating)	-	15000	-
Clause 6 of IS 2266, IS 6594 Clause 5.2(Ovality)	-	15000	-
Clause 6 of IS 2266, IS 6594 Clause 6.4(Length)	-	15000	-
Clause 6 of IS 2266, IS 6594 Clause 7(Freedom from defect)	-	15000	-
Clause 6 of IS 2266, IS 6594 Clause 10.3.3(Torsion Test)	-	15000	-
Clause 6 of IS 2266, IS 6594 Clause 10.3.4(Reverse Bend)	-	15000	-
Clause 6 of IS 2266, IS 6594 Clause 6.7.1(Length of Lay)	-	15000	-
Clause 6 of IS 2266, IS 6594 Clause 6.7.2(Direction of Lay)	-	15000	-
Clause 6 of IS 2266, IS 6594 Clause 10.3.1.1(Tensile Test (Individual Wire))	-	15000	-
Clause 6 of IS 2266, IS 6594 Clause 10.3.1.1(Torsion Test (Indiviual Wire))	-	15000	-
Clause 6 of IS 2266, IS 6594 Clause 10.3.1.1(Reverse Bend test (Individual Wire))	-	15000	-
Clause 6 of IS 2266, IS 6594 Clause 10.3.6(Diameter of Wire)	-	15000	-
Clause 8.2(Grade-1, Table-1, IS 1835:1976, Carbon)	-	-	-
Clause 8.2(Manganese)	-	-	-
Clause 8.2(Silicon)	-	-	-
Clause 8.2(Sulphur)	-	-	-
Clause 8.2(Phosphorus)	-	-	-
Clause 8.2(Copper)	-	-	-
Clause 8.2(Nickel)	-	-	-
Clause 8.2(Chromium)	-	-	-
Clause 8.2(Phosphorus+ Sulphur)	-	-	-
Clause 8.2(Grade-2, Table-1, IS 1835:1976, Carbon)	-	-	-
Clause 8.2(Grade-3, Table-1, IS 1835:1976, Carbon)	-	-	-
Clause 8.2(Grade-4, Table-1, IS 1835:1976, Carbon)	-	-	-
12(a) Size)	-	-	-
12(b) Construction)	-	-	-
12(c) Rope Grade)	-	-	-
12(d) lay)	-	-	-
12(e) Core coating)	-	-	-
12(f) length of wire rope)	-	-	-
12(g) Reel/coil number along with the order number)	-	-	-
12(h) BIS Standards Mark)	-	-	-
4(Rope Size and Tolerance )	-	-	-
5(Minimum Breaking Force)	-	-	-
6(General Requirements)	-	-	-
7(Construction)	-	-	-
8(a) Fibre Core)	-	-	-
8(b) Steel Core)	-	-	-
9(Joints)	-	-	-
10(Galvanizing)	-	-	-
6.1(Water soluble acids)	-	-	-
6.2(Salts)	-	-	-
Clause 6 of IS 2266, Table 1-13 IS 2266, IS 6594 Clause 6.5(Mass)	-	-	-
Clause 10(Mass of Zinc Coating)	-	-	-
Clause 10(Uniformity of Coating)	-	-	-
Clause 6 of IS 2266, IS 6594 Clause 5.2(Ovality)	-	-	-
Clause 6 of IS 2266, IS 6594 Clause 6.4(Length)	-	-	-
Clause 6 of IS 2266, IS 6594 Clause 7(Freedom from defect)	-	-	-
Clause 6 of IS 2266, IS 6594 Clause 10.3.3(Torsion Test)	-	-	-
Clause 6 of IS 2266, IS 6594 Clause 10.3.4(Reverse Bend)	-	-	-
Clause 6 of IS 2266, IS 6594 Clause 6.7.1(Length of Lay)	-	-	-
Clause 6 of IS 2266, IS 6594 Clause 6.7.2(Direction of Lay)	-	-	-
Clause 6 of IS 2266, IS 6594 Clause 10.3.1.1(Tensile Test (Individual Wire))	-	-	-
Clause 6 of IS 2266, IS 6594 Clause 10.3.1.1(Torsion Test (Indiviual Wire))	-	-	-
Clause 6 of IS 2266, IS 6594 Clause 10.3.1.1(Reverse Bend test (Individual Wire))	-	-	-
Clause 6 of IS 2266, IS 6594 Clause 10.3.6(Diameter of Wire)	-	-	-

Complete

25 Feb, 2027

-
Included w.e.f. 23.06.2023

150

IS 9763 (2000)

Plastics Bib Taps, Pillar Taps, Angle Valves and Stop Valves for Hot and Cold Water Services -

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
(Cl. 5)(Nominal Size)	-	12500	-
(Cl. 7)(Identification)	-	12500	-
(Cl. 4)(Materials)	-	12500	-
(Cl.6 , Table 3)(Dimensions)	-	12500	-
(Cl 8)(Construction,Workmanship and Finish)	-	12500	-
(Cl 8.4)(Minimum Thickness)	-	12500	-
(Cl. 8.5)(Finish)	-	12500	-
(Cl 9.1)(Resistance to Residual Chlorine in Water)	-	12500	-
(Cl 9.2)(Drip Proofness Test)	-	12500	-
(Cl 9.3)(Thermal Shock Test )	-	12500	-
(Cl 9.4)(Hydraulic Pressure Test)	-	12500	-
(Cl 9.5)(Mechanical Strength Characteristics)	-	12500	-
(Cl. 5)(Nominal Size)	-	-	-
(Cl. 7)(Identification)	-	-	-
(Cl. 4)(Materials)	-	-	-
(Cl.6 , Table 3)(Dimensions)	-	-	-
(Cl 8)(Construction,Workmanship and Finish)	-	-	-
(Cl 8.4)(Minimum Thickness)	-	-	-
(Cl. 8.5)(Finish)	-	-	-
(Cl 9.1)(Resistance to Residual Chlorine in Water)	-	-	-
(Cl 9.2)(Drip Proofness Test)	-	-	-
(Cl 9.3)(Thermal Shock Test )	-	-	-
(Cl 9.4)(Hydraulic Pressure Test)	-	-	-
(Cl 9.5)(Mechanical Strength Characteristics)	-	-	-

Complete

25 Feb, 2027

-
Included w.e.f. 23.06.2023

First
Prev
4
5
6
7
Next
Last

Bureau of Indian Standards

The National Standards Body of India

Atmy Analytical Labs Pvt. Ltd.

I-30,DLF Industrial Area, Phase-1, Faridabad, Faridabad, Haryana, 121003

9910808996 info@atmylabs.com

Scope List