BIS - LIMS (Laboratory Information Management System)

BIS, Central Laboratory (CL)

20/9, Site 4, Sahibabad Industrial Area, Sahibabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201010

- sample@bis.gov.in

Scope List

Reset

998 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

781

IS 8737 (2017)

Valve fittings for use with liquefied petroleum gas (LPG) cylinders for more than 5 litre water capacity - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.3.1a (Tensile Strength-IS 1608)	-
4.3.1b (Elongation-IS 1608)	-
4.4 (Izod impact strength-IS 1598)	-
5.1.1a Fig 1,2 (SCREW THREADS ON THE VALVE STEM- Type 1 Threads-IS 15894)	-
7.1 (Design Requirements)	-
7.3 (Design Requirements)	-
7.4 (Design Requirements)	-
7.5 (Design Requirements)	-
7.6 (Design Requirements)	-
7.8ai Annex D of IS 9798 (All rubber and other moulded parts coming in contact with LPG in the construction of the valve shall be compatible with LPG, when tested according to Annex D of IS 9798)	-
7.8bi Annex H of IS 9798. (All rubber and other moulded parts shall be suitable for extreme climatic conditions in which the valve is likely to be used, the range of temperature being -20°C to + 65°C. The method of test shall be according to Annex H of IS 9798.)	-
4.6.2,4.6.2.1,4.6.2.2a (Moulded parts (plastics, etc) shall be subjected to immersion test (resistance to hydrocarbons)(Cl.4.6.2.1) Increase in mass :)	-
7.10 (The minimum finished wall thickness at any portion of the valve shall not be less than 2.5 mm)	-
8.1 (Stress Corrosion Test for Copper Alloy As per IS 2305)	-
8.2 (Hydrostatic Test)	-
8.3.1 (Pneumatic Test: Tightness of Joint Packing (in Valve Outlet) and Valve Spindle)	-
8.3.2 (Pneumatic Test: Tightness of Valve Spindle and Valve Housing)	-
8.3.3 (Pneumatic Test: Tightness of Joint Packing and Housing)	-
9.2a (Cycle Test)	-
9.2bi (After the cycle test, the valve shall besubjectedto the pneumatic test given in 8.3 and shall performsatisfactorily:- lPneumatic Test ,after cycle test: Tightness of Joint Packing (in Valve Outlet) and Valve Spindle)	-
9.2bii (Pneumatic Test ,after cycle test: Tightness of Valve Spindle and Valve Housing)	-
9.2biii (Pneumatic Test ,after cycle test: Tightness of Joint Packing and Housing)	-
9.3 (Operation Test)	-
9.4 (Valve Fitting Testing Torque :)	-
9.5a Table 3,Fig. 8 (Impact Test)	-
9.5bi (After the Impact test, the valve shall satisfy Pneumatic test as perCl.8.3:- lPneumatic Test ,after cycle test: Tightness of Joint Packing (in Valve Outlet) and Valve Spindle)	-
9.5bii (Pneumatic Test ,after cycle test: Tightness of Valve Spindle and Valve Housing)	-
9.5biii (Pneumatic Test ,after cycle test: Tightness of Joint Packing and Housing)	-
4.3.1a (Tensile Strength-IS 1608)	-
6.2 (VALVE OUTLET CONNECTIONS: Spring loaded self-closing Valve)	-
4.2.1Sl.No.i (Copper)	-
4.2.1Sl.No.ii (Lead)	-
4.2.1Sl.No.iii (Iron)	-
4.2.1Sl.No.iv (Manganese)	-
4.2.1Sl.No.vi (Zinc)	-
4.2.1Sl.No.v (others(inclusive of iron))	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm; excluding -; (Cl 4.6.1.1)-Ozone test (Resistance to ozone cracking)

782

IS 5986 (2017)

Hot rolled steel sheet, plate and strip for forming and flanging purposes - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (UTM)	-
Cl 9 (Press)	-
Cl 13 (Workmanship)	-
Cl 15 (Length, Width & Thickness)	-
7.1 (Carbon %)	-
7.1 (Sulphur %)	-
7.1 (Phosphorus %)	-
7.1 (Manganese %)	-
7.1 (Silicon %)	-
7.1 ( Aluminium %)	-
7.1 ( Nitrogen%)	-
7.1 ( Copper %)	-
7.1 (V)	-
7.1 ( Ti)	-
7.1 (Cr)	-
7.1 (Mo)	-
7.1 ( Nb)	-
Cl. 7 (Micro Alloy)	-
Cl. 7 (CE)	-
Cl. 7 (Boron)	-
Cl. 7 (Ti+Nb+V+B)	-
Cl. 7 (Cr+Ni+Mo)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm; excluding -; i)Hole Expansion Ratio Test(CL 11)

783

IS 15182 (2002)

Propiconazole EC - Specification

Rs.2450.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2.1 (Description)	-
3.2.2 (Cold Test)	-
3.2.3 (Flash Point (Abel))	-
3.2.4 (Emulsion Stability)	-
3.3.1 (Pretilachlor content)	-
3.3.2 (Acidity)	-

-
excluding Cl. 3.3.1 Propiconazole Content;

784

IS 14158 (1994)

Cyfluthrin WP - Specification

Rs.5600/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2 (Description)	-
3.3 Table 1 i (Cyfluthrin content )	-
3.3 Table 1 ii (Sieving requirements material passing through 75 micron IS sieve)	-
3.3 Table 1 iii (Suspensibility)	-
3.3 Table 1 iv (Acidity/Alkalinity)	-
3.3 Table 1 v (Wettability)	-

-
excluding Cl 3.3, Table1, Sl No. I & III Content & Suspensibility;

785

IS 15219 (2002)

Aluminium phosphide powder formulation

Rs.1550.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2 (Description)	-
3.3.1 (Aluminium Phosphide Content)	-

-
-

786

IS 6967 (1973)

Specification for steels for electrically welded round link chains

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 Table 2 (Carbon- IS 228)	-
5.1 Table 2 (Manganese- IS 228)	-
5.1 Table 2 (Sulphur- IS 228)	-
5.1 Table 2 (Phosphorous- IS 228)	-
5.1 Table 2 (Silicon- IS 228)	-

-
-

787

IS 1660 (2009)

Wrought aluminium utensils - Specification (First Revision)

Rs 6760/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (Classification Heavy/Medium/L:ight)	-
0.5 (Fabrication)	-
5.1 (The utensil shall be pressed or spun from one piece)	-
5.2 ( Body Thickness of the thinnest part of the finished utensil, mm Not declared )	-
5.2 (Lid Thickness of the finished utensil, mm)	-
6.1 & Table 1 ( i) Name of Utensil )	-
6.1 & Table 1 (ii) Shape of Utensil)	-
6.1 & Table 1 ( Nominal Size, mm)	-
6.1 & Table 1 (Inside dia, Φ D mm Not declared )	-
6.1 & Table 1 (Outside dia Ф NA)	-
6.1 & Table 1 (Height NA)	-
6.1 & Table 1 (Capacity, l NA)	-
6.1 ( Minimum sheet thickness for nominal size )	-
7.1 (HANDLES ,When fitted shall be of aluminium, stainless steel or of other suitable fire resistance material These shall be fastened to the utensils by tightly drawn aluminium or stainless steel rivets, by welding, by screwing to cast bosses or by riveting between flange at the end of the handles. Handles shall be so shaped and positioned to facilitate the carrying and handling of the utensils in normal use )	-
7.2 (Handles shall be sufficiently strong to support a mass in the utensils equivalent to three times the mass of the water capacity of the utensils in the position of normal use without visible permanent deformation of the handle or utensil)	-
8.1 (The utensils shall be clean reasonably free from distortion, dents, wrinkles, wavy surface, burrs, scratches, pitting and deep tool marks and other surface defects)	-
8.2 (The design of the utensils shall be such that it is easy to clean and prevent accumulation of dirt)	-
8.4.1.2 ( Finish of the coating: The coating shall be smooth continuous and uniform in appearance, and shall be adherent. It shall be free from powdery areas, loose films and discontinuities, such as breaks and scratches. The size and number of contact marks shall be minimum consistent with good practice.)	-
( Clauses 4, 4.1, 4.2 and 4.3) (Copper of IS 21)	-
( Clauses 4, 4.1, 4.2 and 4.3) (Magnesium of IS 21)	-
( Clauses 4, 4.1, 4.2 and 4.3) (Silicon of IS 21)	-
( Clauses 4, 4.1, 4.2 and 4.3) (Iron of IS 21)	-
( Clauses 4, 4.1, 4.2 and 4.3) (Manganese of IS 21)	-
( Clauses 4, 4.1, 4.2 and 4.3) (Zinc of IS 21)	-
( Clauses 4, 4.1, 4.2 and 4.3) (Chromium of IS 21)	-
( Clauses 4, 4.1, 4.2 and 4.3) (Titanium / other Grain of IS 21)	-
8.4.2 (A coating of thickness 25 to 100 microns is generally required)	-
8.4.3 (Abrasion Resistance When the coating surface is rubbed two or three times with emery paper with emery conforming to grit number 180 using medium finger pressure, it shall not abrade the surface but shall skid over the surface showing not more than a trace of whitening of the surface)	-
8.4.4 (The colour of the hard anodic coating varies depending upon the alloy, thickness of the coating and electrolye. Normally the colour may vary from dark grey (almost black) to light grey. )	-
8.4.4 (The film will appear dark grey when wet. )	-
8.4.5 (When the coated surface is rubbed two or three times with fine emery paper grit number 180 using medium finger pressure, cloth or paper shall not abrade the surface. A faint trace of whitening on the cloth or paper is permissible)	-
9 (The manufacturer shall provide full instructions for use and cleaning for coated or hard anodized utensils)	-
10 (Each vessel shall be legibly and indelibly stamped on the outside surface or handle with the manufacturer’s name or registered trade-mark, size and thickness or class. )	-
Clause 8.6.1 (Performance test)	-
Clause 8.6.2 (Ground Nut Oil Test for Leakage)	-
5.4 (Qualitative and Anodized Coating)	-
5.5 (Qualitative and Anodized Coating)	-
8.3 (Anodized Coating)	-
8.5 (Plastic Coating)	-
8.1 (Qualitative)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm; excluding TF not available for 1. Coating test 2. Hard Anodized;

788

IS 11513 (2017)

Hot rolled carbon steel strip for cold rolling purposes - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (Workmanship)	-
Cl 9 (Length, Width, Thickness, Crown, Edge Camber & Difference in Thickness Across Width )	-
6.1 (Carbon %)	-
6.1 (Sulphur %)	-
6.1 (Phosphorus %)	-
6.1 (Manganese %)	-
6.1 (Silicon %)	-
6.1 ( Aluminium %)	-
6.1 ( Nitrogen%)	-
6.1 (Boron)	-
6.1 ( Copper %)	-
6.1 ( Ti)	-
6.1 (V)	-
6.1 ( Nb)	-
6.1 (Microalloying)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm;

789

IS 336 (1973)

Specification for ether

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl no .3.2 (Odour and Taste )	-
Cl no .3.3.1 (Composition )	-
Cl no .3.4 (Solubility )	-
Cl no .3.5 [ Table 1, Sl no.(i) ] Appendix A 2 (Relative density at 20 °C Solvent Grade )	-
Cl no .3.5 [ Table 1, Sl no.(iv) ] Appendix A 5 (Residue on Evaporation )	-
Cl no .3.5 [ Table 1, Sl no.(v) ] Appendix A 6 (Methyl alcohol )	-
Cl no .3.5 [ Table 1, Sl no.(vi) ] Appendix A 7 (Aldehydes and acetone )	-
Cl no .3.5 [ Table 1, Sl no.(vii) ] Appendix A 8 (Sulphurous acids and other free acids )	-

-
excluding iii) Distillation range;

790

IS 2028 (2004)

Open jaw wrenches (Spanners) - Specification (Fijih Revision)

Rs.3700/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (Dimensions- a)	-
3.1 (Dimensions- b)	-
3.1 (Dimensions- l)	-
3.2, 3.3, 3.4 (Dimensions- a)	-
3.2, 3.3, 3.4 (Dimensions- b1)	-
3.2, 3.3, 3.4 (Dimensions- b2)	-
3.2, 3.3, 3.4 (Dimensions- l)	-
5 (Hardness- upto 32 mm)	-
5 (Hardness- over 32 mm)	-
6 (Workmanship And Finish)	-
6 (Workmanship And Finish)	-

-
Please refer status of IS 3748 for test facility status of Chemical disciplince.; excluding -; i)Torque testing(CL 8)

791

IS 6240 (2008)

Hot rolled steel plate (Up To 6 Mm) sheet and strip for the manufacture of low pressure liquefiable gas cylinders (Fourth Revision)

9710 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 7 (UTM)	-
Cl 8 (Press)	-
Cl 9 (Strainage Embrittlement)	-
Cl 10 (Erichsen Cupping)	-
Cl 13 (Length, Width & Thickness)	-
6.1 (Carbon %)	-
6.1 (Sulphur %)	-
6.1 (Phosphorus %)	-
6.1 (Manganese %)	-
6.1 (Silicon %)	-
6.1 ( Aluminium %)	-
6.1 (Nitrogen%)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm;

792

IS 14276 (2016)

Cement bonded particle boards - Specification (First Revision)

11797 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 (Finish)	-
7 (Dimensions and Tolerances)	-
8.5 (Workability)	-
10.3, Table-1 (Test for Density)	-
10.5, Table-1 (Test for Water Absorption)	-
10.6, Table-1 (Test for swelling in water)	-
10.7, Table-1 (Test for modulus of Rupture)	-
10.8, Table-1 (Test for modulus of Elasticity)	-
10.9, Table-1 (Test for tensile strength perpendicular to Surface)	-
10.1, Table-1 (Test for Screw Withdrawal Strength)	-
Clause 8.2 Table 1 (Moisture content)	-

-
"Test facility not available for 10.8 Tensile Strength Perpendicular to Surface After Ageing, 10.10 -Abrasion Resistance, 10.11 - Resistance to Steam, 10.14 - Resistance to Stain ,; " Sample Test Parameter not available in CL: 10.5 Test for Water Absorption, 10.6 Test for Swelling in Water, 10.7 Test for Modulus of Rupture(Wet),10.8 Test for Modulus of Elasticity (Wet), 10.9Test for Tensile Strength Perpendicular to Surface (accelerated ageing test)," SIZE: 2 Boards Of Full Size Sample Size without dimensional measurements: Length-1200 mm, width-1200

793

IS 2645 (2003)

Integral waterproofing compounds for cement mortar and concrete - Specification (Second Revision)

Rs.12770.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 3.3 (Compressive Strength, At 3days & 7 days)	-
Cl 3.2 (Initial & Final)	-
Clause 3.4 (Chloride content)	-
Cl 3.1 (The permeability of water in specimen Prepared with WPC shall be less than half the permeability of plain cement specimens. (i.e ; < 50 percent))	-
Clause 3.1 (Permeability to water of cement mortar with Water proofing compound)	-

-
complete

794

IS 13785 (1993)

Pesticide - Dodine WP - Specification

Rs.3350.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2 (Description)	-
3.3 Table 1 i (Dodine content)	-
3.3 Table 1 ii (Sieving requirements material passing through 75 micron IS sieve)	-
3.3 Table 1 iv (Acidity/Alkalinity)	-
3.3 Table 1 v (Wettability)	-

-
-

795

IS 13692 (1993)

Metalaxyl mancqzeb WP - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2 (Description)	-
3.3 Table 1 i (Metalaxyl content,)	-
3.3 Table 1 iii (Sieving requirements material passing through 75 micron IS sieve)	-
3.3 Table 1 v (Wettability)	-

-
excluding Table1 Cl. 3.3, Sl. No. 2 Metalaxyl Content;

796

IS 15965 (2012)

Pre - Painted aluminium zinc alloy metallic coated steel strip and sheet (Plain)

Rs 2850/ View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 7 (Workmanship)	-
Cl 8.3.1 (Adhesion )	-
Cl 9.1 (Workmanship)	-
Cl 11 (Length, Width & Thickness)	-
Cl 12 (Camber, Deviation From Squareness (Out-of- Square) & Deviation From Flatness)	-
Cl 12 (Weight)	-
4, 5 (CARBON)	-
4, 5 (SULPHUR)	-
4, 5 (PHOSPHURS)	-
4, 5 (MANGANESE)	-
4, 5 (SILICON)	-
4, 5 (ALUMINIUM)	-
4, 5 (NITROGEN)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm; excluding Except Coating; i)Solvent resistance test (As per annex C) ii)Dry film thickness(As per ISO 2808 -method 5B iii)Corrosion resistance(As per IS 9844) iv)Humudity Resistance (IS 101(Part 6/sec1))

797

IS 8042 (2015)

White portland cement - Specification (Third Revision)

Rs 12050/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 -Table 2- i (Fineness 4031 Part 2)	-
6 -Table 2- ii- a (Expansion by Le Chatelier- 4031 Part 3)	-
6 -Table 2- ii- b (Expansion by Autoclave- 4031 Part 3)	-
6 -Table 2- iii- a (Setting Time Initial- 4031 Part 5)	-
6 -Table 2-iii- b (Setting Time Final- 4031 Part 5)	-
6 -Table 2- iv- a (Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-
6 -Table 2- iv- b (Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-
6 -Table 2- iv- c (Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-
6 -Table 2- vi (Degree of whiteness-Annex B)	-
5 - Table - 1 i (Ratio of percentage of lime to percentages of silica, alumina and iron oxide - Cl 4 of IS 4032:1985)	-
5 - Table - 1 iii (Insoluble residue - Cl 4.10 of IS 4032:1985)	-
5 - Table - 1 ii (Iron oxide - Cl 4.5 of IS 4032:1985)	-
5 - Table - 1 iv (Magnesia - Cl 4.8 of IS 4032:1985)	-
5 - Table - 1 v (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-
5 - Table - 1 vi (Loss on ignition - Cl 4.2 of IS 4032:1985)	-
5 - Table - 1 vii (Chloride content - Cl 4.13 of IS 4032:1985)	-
Clause 6 Table 2, SI No. (v) (Compressive strength of Transverse Specimen, 672 ± 4 h)	-

-
Complete for chemical.;

798

IS 15961 (2012)

Hot dip aluminium - Zinc alloy metallic coated steel strip and sheet (Plain)

Rs.4990 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (UTM)	-
Cl 9 & Table 2 (Workmanship)	-
Cl 10 (Coating Adhesion )	-
Cl 11 (Workmanship)	-
Cl 12 (Weight)	-
Cl 13 (Length, Width, Thickness, Camber, Deviation From Squareness & Deviation From Flatness)	-
4, 5 (CARBON)	-
4, 5 (SULPHUR)	-
4, 5 (PHOSPHURS)	-
4.5 (MANGANESE)	-
4, 5 (SILICON)	-
4, 5 (ALUMINIUM)	-
4, 5 (NITROGEN)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm; excluding Except Coating; i) Coating Test for single surface(Cl 9)

799

IS 13457 (1992)

Pesticide - Deltamethrin WP specification

Rs.5000.00 (including cost of CRM). View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2 (Description)	-
Cl. 3.3&3.3.1 Table 1 (Deltamethrin content, )	-
Cl. 3.3 Table 1 (Sieving (material passing through 45 Micron IS Sieve),)	-
Cl. 3.3 Table 1 (Suspensibility, )	-
Cl. 3.3 Table 1 (Acidity (as H2SO4), or Alkalinity (as NaOH))	-
Cl. 3.3 Table 1 (Wettability )	-

-
-

800

IS 996 (2009)

Single phase a.c. induction motors for general purpose (Third Revision)

2150 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
16.1 (Marking and Diagram of connenctions)	-
16.1 (Marking and Diagram of connenctions)	-
16.1 (Marking and Diagram of connenctions)	-
16.1 (Marking and Diagram of connenctions)	-
16.1 (Marking and Diagram of connenctions)	-
16.1 (Marking and Diagram of connenctions)	-
16.1 (Marking and Diagram of connenctions)	-
16.1 (Marking and Diagram of connenctions)	-
16.1 (Marking and Diagram of connenctions)	-
16.1 (Marking and Diagram of connenctions)	-
16.1 (Marking and Diagram of connenctions)	-
16.1 (Marking and Diagram of connenctions)	-
16.1 (Marking and Diagram of connenctions)	-
16.1 (Marking and Diagram of connenctions)	-
16.1 (Marking and Diagram of connenctions)	-
16.1 (Marking and Diagram of connenctions)	-
10 (Type of enclosures)	-
11 (Methods of cooling)	-
9 (General construction (as per Cl. 9 & F-3))	-
9.1 (General construction (as per Cl. 9 & F-3))	-
9.4.11 (General construction (as per Cl. 9 & F-3))	-
9 (General construction (as per Cl. 9 & F-3))	-
9.4.13 (General construction (as per Cl. 9 & F-3))	-
4.1 (Rated Voltage)	-
4.2 (Rated Frequency)	-
4.3 (Rated Output)	-
4.4 (Rated Speed)	-
7 (Dimensions (Cl.App.F-4))	-
9.5 (Earthing)	-
9.5 (Earthing)	-
9.5 (Earthing)	-
17.3 (a) (No load test at rated voltage and frequency )	-
17.3 (a) (No load test at rated voltage and frequency)	-
17.3 (a) (No load test at rated voltage and frequency)	-
12.1.1 (Test for torques at rated voltage and frequency (Cl.12.1.1 & F-6.2 ))	-
12.1.1 (Test for torques at rated voltage and frequency (Cl.12.1.1 & F-6.2 ))	-
12.1.1 (Test for torques at rated voltage and frequency (Cl.12.1.1 & F-6.2 ))	-
12.1.1 (Test for Breakaway starting current at rated voltage and frequency (Cl.12.1.1 & Cl. 12.5))	-
12.5.1 (Full load performance at rated voltage and frequency (Cl.12.5 & F-6.2.4 ))	-
12.5.1 (Full load performance at rated voltage and frequency (Cl.12.5 & F-6.2.4 ))	-
12.5.1 (Full load performance at rated voltage and frequency (Cl.12.5 & F-6.2.4 ))	-
12.5.1 (Full load performance at rated voltage and frequency (Cl.12.5 & F-6.2.4 ))	-
12.5.1 (Full load performance at rated voltage and frequency (Cl.12.5 & F-6.2.4 ))	-
12.5.1 (Full load performance at rated voltage and frequency (Cl.12.5 & F-6.2.4 ))	-
12.2 (Temperature-rise test (Cl.12.2 & Cl.F-6.2.5))	-
12.2 (Temperature-rise test (Cl.12.2 & Cl.F-6.2.5))	-
12.2 (Temperature-rise test (Cl.12.2 & Cl.F-6.2.5))	-
12.7 (Insulation resistance test)	-
13.1 (High voltage test)	-
13.2 (Moisture proofness)	-
13.2 (Moisture proofness)	-
13.3 (Leakage current test)	-
15.1 (ADDITIONAL TESTS (For ECO - MARK))	-
15.2 (Specific Requirements)	-
16.1 (Marking and Diagram of connenctions)	-
16.1 (Marking and Diagram of connenctions)	-
16.1 (Marking and Diagram of connenctions)	-
16.1 (Marking and Diagram of connenctions)	-
16.1 (Marking and Diagram of connenctions)	-
9.4.11 (General construction (as per Cl. 9 & F-3))	-
12.6 (Vibration Severity)	-

-
Complete upto 180 Watt except Foot & Flange Mounted;

801

IS 12751 (1989)

Pesticides - Pendimethalin EC - Specification

Rs.5400/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2.1 (Description)	-
3.2.2 (Cold Test)	-
3.2.3 (Flash Point (Abel))	-
3.2.4 (Emulsion Stability)	-
3.3.1 (Pendimethalin content)	-
3.4 (Acidity/Alkalinity)	-

-
excluding Cl. 3.3.1 Pendimethalin Content;

802

IS 299 (2012)

Alumino - Ferric - Specification (Fifth Revision)

Please see remarks View breakup
As decided by Competent Authority, the testing charges are Rs.3250.00 (for Grade 1, 2 & 3) and Rs.8250.00 (for Grade 4 & 5).

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
1 (i) Table 1 ( Insouble matter, Grade 1, A-3)	-
1 (i) Table 1 ( Insouble matter, Grade 2, A-3)	-
1 (i) Table 1 ( Insouble matter, Grade 3, A-3)	-
1 (i) Table 1 ( Insouble matter, Grade 4, A-3)	-
1 (i) Table 1 ( Insouble matter, Grade 5, A-3)	-
1 (ii) Table 1 (Soluble iron compound (as Fe2+ and Fe3+), Grade 1, A-4)	-
1 (ii) Table 1 (Soluble iron compound (as Fe2+ and Fe3+), Grade 2, A-4)	-
1 (ii) Table 1 (Soluble iron compound (as Fe2+ and Fe3+), Grade 3, A-4)	-
1 (ii) Table 1 (Soluble iron compound (as Fe2+ and Fe3+), Grade 4, A-4)	-
1 (ii) Table 1 (Soluble iron compound as Fe2+ and Fe3+), Grade 5, A-4)	-
1 (iii) Table 1 (Water soluble aluminium compounds (as Al2O3), Grade 1, A-5)	-
1 (iii) Table 1 (Water soluble aluminium compounds (as Al2O3), Grade 2, A-5)	-
1 (iii) Table 1 (Water soluble aluminium compounds (as Al2O3), Grade 3, A-5)	-
1 (iii) Table 1 (Water soluble aluminium compounds (as Al2O3), Grade 4, A-5)	-
1 (iii) Table 1 (Water soluble aluminium compounds (as Al2O3), Grade 5, A-5)	-
1 (iv) Table 1 (pH (of 5 percent aqueous solution), Grade 1, A-6)	-
1 (iv) Table 1 (pH (of 5 percent aqueous solution), Grade 2, A-6)	-
1 (iv) Table 1 (pH (of 5 percent aqueous solution), Grade 3, A-6)	-
1 (iv) Table 1 (pH (of 5 percent aqueous solution), Grade 4, A-6)	-
1 (iv) Table 1 (pH (of 5 percent aqueous solution), Grade 5, A-6)	-
1 (v) Table 1 (Free acidity (as H2SO4)/Basicity (as Al2O3), Grade 1, A-7)	-
1 (v) Table 1 (Free acidity (as H2SO4)/Basicity (as Al2O3), Grade 2, A-7)	-
1 (v) Table 1 (Free acidity (as H2SO4)/Basicity (as Al2O3), Grade 3, A-7)	-
1 (v) Table 1 (Free acidity (as H2SO4)/Basicity (as Al2O3), Grade 4, A-7)	-
1 (v) Table 1 (Free acidity (as H2SO4)/Basicity (as Al2O3), Grade 5, A-7)	-
1 (vi) Table 1 ( Lead (as Pb), Grade 1, A-8)	-
1 (vi) Table 1 ( Lead (as Pb), Grade 2, A-8)	-
1 (vi) Table 1 ( Lead (as Pb), Grade 3, A-8)	-
1 (vi) Table 1 ( Lead (as Pb), Grade 4, A-8)	-
1 (vi) Table 1 ( Lead (as Pb), Grade 5, A-8)	-
1 (vii) Table 1 (Arsenic (as As2O3), Grade 1, A-9)	-
1 (vii) Table 1 (Arsenic (as As2O3), Grade 2, A-9)	-
1 (vii) Table 1 (Arsenic (as As2O3), Grade 3, A-9)	-
1 (vii) Table 1 (Arsenic (as As2O3), Grade 4, A-9)	-
1 (vii) Table 1 (Arsenic (as As2O3), Grade 5, A-9)	-
1 (viii) Table 1 (Mercury (as Hg), Grade 1, A-10)	-
1 (viii) Table 1 (Mercury (as Hg), Grade 2, A-10)	-
1 (viii) Table 1 (Mercury (as Hg), Grade 3, A-10)	-
1 (viii) Table 1 (Mercury (as Hg), Grade 4, A-10)	-
1 (viii) Table 1 (Mercury (as Hg), Grade 5, A-10)	-
1 (ix) Table 1 (Manganese (as Mn), Grade 1, A-11)	-
1 (ix) Table 1 (Manganese (as Mn), Grade 2, A-11)	-
1 (ix) Table 1 (Manganese (as Mn), Grade 3, A-11)	-
1 (ix) Table 1 (Manganese (as Mn), Grade 4, A-11)	-
1 (ix) Table 1 (Manganese (as Mn), Grade 5, A-11)	-
1 (x) Table 1 (Chromium (as Cr), Grade 1, A-12)	-
1 (x) Table 1 (Chromium (as Cr), Grade 2, A-12)	-
1 (x) Table 1 (Chromium (as Cr), Grade 3, A-12)	-
1 (x) Table 1 (Chromium (as Cr), Grade 4, A-12)	-
1 (x) Table 1 (Chromium (as Cr), Grade 5, A-12)	-
1 (xi) Table 1 (Cadmium (as Cd), Grade 1, A-13)	-
1 (xi) Table 1 (Cadmium (as Cd), Grade 2, A-13)	-
1 (xi) Table 1 (Cadmium (as Cd), Grade 3, A-13)	-
1 (xi) Table 1 (Cadmium (as Cd), Grade 4, A-13)	-
1 (xi) Table 1 (Cadmium (as Cd), Grade 5, A-13)	-
1 (xii) Table 1 (Selenium (as Se), Grade 1, A-14)	-
1 (xii) Table 1 (Selenium (as Se), Grade 2, A-14)	-
1 (xii) Table 1 (Selenium (as Se), Grade 3, A-14)	-
1 (xii) Table 1 (Selenium (as Se), Grade 4, A-14)	-
1 (xii) Table 1 (Selenium (as Se), Grade 5, A-14)	-
1 (xiii) (a) Table 1 (Organic impurities:Phenolic compounds (as C6H5OH), Garde 1, A-15)	-
1 (xiii) (a) Table 1 (Organic impurities:Phenolic compounds (as C6H5OH), Garde 2, A-15)	-
1 (xiii) (a) Table 1 (Organic impurities:Phenolic compounds (as C6H5OH), Garde 3, A-15)	-
1 (xiii) (a) Table 1 (Organic impurities:Phenolic compounds (as C6H5OH), Garde 4, A-15)	-
1 (xiii) (a) Table 1 (Organic impurities:Phenolic compounds (as C6H5OH), Garde 5, A-15)	-
1 (xiii) (b) Table 1 (Anionic detergents (as MASS), Garde 1, A-16)	-
1 (xiii) (b) Table 1 (Anionic detergents (as MASS), Garde 2, A-16)	-
1 (xiii) (b) Table 1 (Anionic detergents (as MASS), Garde 4, A-16)	-
1 (xiii) (b) Table 1 (Anionic detergents (as MASS), Garde 5, A-16)	-
1 (xiii) (b) Table 1 (Anionic detergents (as MASS), Garde 3, A-16)	-

-
-

803

IS 6006 (2014)

Uncoated stress relieved strand for prestressed concrete - Specification (Second Revision)

Rs 4035/- Excluding Proof Stress and Relaxation Test View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5 (Weight)	-
Cl 7 (Tensile Test On UTM)	-
Cl 4 (Length )	-
Cl 4 (Joints)	-
Cl 4 (Butt Joint)	-
Cl 4.5 (Workmanship)	-
4.1.2 (sulphur)	-
4.1.2 (phosphorus)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm; excluding -; i)Fixture for tensile test(As per Annex C), Relaxation Test

804

IS 6527 (1995)

Stainless steel wire rods - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (Heat Treatment)	-
Cl 9 (Tensile & Hardness)	-
Cl 10 (Diameter & Out Of Round)	-
7, Table 1of IS:6527 (Designation X04Cr13) (Carbon)	-
7, Table 1of IS:6527 (Designation X04Cr13) (Sulphur)	-
7, Table 1of IS:6527 (Designation X04Cr13) (Phosphorous)	-
7, Table 1of IS:6527 (Designation X04Cr13) (Manganese)	-
7, Table 1of IS:6527 (Designation X04Cr13) (Silicon)	-
7, Table 1of IS:6527 (Designation X04Cr13) (Aluminium)	-
7, Table 1of IS:6527 (Designation X04Cr13) (Chromium)	-
7, Table 1of IS:6527 (Designation X04Cr13) (Nickel)	-
7, Table 1of IS:6527 (Designation X04Cr13) (Molybdenum)	-
7, Table 1of IS:6527 (Designation X04Cr13) (Copper)	-
7, Table 1of IS:6527 (Designation X02Cr18Ni11) (Niobium)	-
7, Table 1of IS:6527 (Designation X02Cr18Ni11) (Titanium)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm; excluding -; i)Extensometer (for Proof stress) ii)Hardness Test for size < 13mm not available

805

IS 12016 (1987)

Specification for cypermethrin EC

Rs.2450.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.2.1 (Description)	-
2.2.2 (Cold Test)	-
2.2.3 (Flash Point (Abel))	-
2.2.4 (Emulsion Stability)	-
2.3.1 (Cypermethrin content)	-
2.3.2 (Acidity)	-

-
excluding Cl 2.3.1 Cypermethrin Content;

806

IS 6003 (2010)

Indented Wire For--Prestressed Concrete ”

Rs.4110/- excl. relaxation test View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5.1 (Diameter)	-
Cl 6.1.2 (Weight)	-
Cl 7.1 (Tensile Test On UTM)	-
Cl 7.2 (Tensile Test On UTM)	-
Cl 7.3 (Reverse Bend Test)	-
Cl 7.4 (Tensile Test On UTM)	-
4.1.1 (Phosphorus %)	-
4.1.1 (Sulphur %)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm; excluding -; i) Relaxation Test (As per CL 8.7)

807

IS 11997 (1987)

Specification for fbnvaleratb AC

Rs 5150/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.2.1 (Description)	-
2.2.2 (Cold Test)	-
2.2.3 (Flash Point (Abel))	-
2.2.4 (Emulsion Stability)	-
2.3.1 (Fenvelarte content)	-
2.3.2 (Acidity/Alkalinity)	-

-
-

808

IS 1008 (2004)

Sugar boiled confectionery - Specification (Second Revision)

Rs 4500/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (Description)	-
5.3 Table 1 i (Ash sulphated)	-
5.3 Table 1 ii (Acid Insoluble ash)	-
5.3 Table 1 iii (Sulphur dioxide)	-
5.3 Table 1 iv (Arsenic)	-
5.3 Table 1 v (Lead)	-
5.3 Table 1 vi (Copper)	-
5.3 Table 1 vii (Zinc)	-
5.3 Table 1 viii (Tin)	-
5.3 Table 2 i (Moisture.)	-
5.3 Table 2 ii (Ash sulphated)	-
5.3 Table 2 iii (Acid insoluble ash)	-
5.3 Table 2 iv (Sulphur dioxide)	-

-
500 gm x 3 excluding 1-Sulphur dioxide;

809

IS 15997 (2012)

Low nickel austenitic stainless steel sheet and strip for utensils and kitchen appliances - Specification

Rs 2850 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 (Freedom From Defects)	-
9.3 (Tensile Test-1608:Part 1)	-
9.3, Table 3 (Yield Strength, Mpa)	-
9.3, Table 3 (Elongation, %)	-
11 (Surface finish)	-
12 (Dimensions)	-
14.1 (Thickness,mm)	-
14.2 ( Width, mm)	-
14.3 (Length, mm)	-
14.4 (Flatness, mm)	-
14.5 (Camber, mm)	-
Cl. 8.1, 8.1.1 & 10.1 Table 1 (Carbon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 8.1, 8.1.1 & 10.1 Table 1 (Silicon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 8.1, 8.1.1 & 10.1 Table 1 (Manganese -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 8.1, 8.1.1 & 10.1 Table 1 (Nickel -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 8.1, 8.1.1 & 10.1 Table 1 (Chromium -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 8.1, 8.1.1 & 10.1 Table 1 (Sulphur -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 8.1, 8.1.1 & 10.1 Table 1 (Phosphorus -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 8.1, 8.1.1 & 10.1 Table 1 (Copper -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 8.1, 8.1.1 & 10.1 Table 1 (Nitrogen -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm; excluding -; Proof stress test (Cl 9.3)

810

IS 3055 : Part 2 (2004)

Clinical thermometers: Part 2 enclosed scale type - Specification (Third Revision)

Rs. 5400.00/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.2.3 (The thermometric liquid shall be pure, dry mercury)	-
5.1 (TEMPERATURE SCALE)	-
5.2 (TEMPERATURE SCALE)	-
7.1 (Patterns)	-
7.3.1 (Sheath )	-
7.3.1.1 (Sheath )	-
7.3.2 (Maximum Indicating Device (Constriction))	-
7.3.2.1 (Hardness of Maximum Indicating Device)	-
7.3.3 (Bulb)	-
7.3.4 (Strip Bearing the Scale)	-
7.3.5 (Constrution)	-
7.3.6 (Constrution)	-
7.4 - Table 1-i (Scale range)	-
7.4 - Table 1-ii (Scale range)	-
7.4 - Table 1-iii (Smallest scale division)	-
7.4 - Table 1-iv (Smallest scale division)	-
7.4 - Table 1-v (Overall length)	-
7.4 - Table 1-vi (Scale length)	-
7.4 - Table 1-vii (Extcn1aI diameter of sheath (round or Oval) )	-
7.4 - Table 1-viii (Bulb length)	-
7.4 - Table 1-ix (Distance from top of the constriction to the 35.5°C mark)	-
7.4 - Table 1-x (Distance from the highest graduation line to top of the sheath)	-
7.4 - Table 1-xi (Scale spacing)	-
7.4 - Table 1-xii (Thickness of stem)	-
7.5.1 (Graduation and Numbering)	-
7.5.2 (Graduation and Numbering)	-
7.5.3 (Graduation and Numbering)	-
7.5.4-a (Graduation and Numbering)	-
7.5.4-b (Graduation and Numbering)	-
7.5.4-c (Graduation and Numbering)	-
7.5.5 (Graduation and Numbering)	-
7.5.6 (Graduation and Numbering)	-
7.5.7 (Graduation and Numbering)	-
7.5.8 (Graduation and Numbering)	-
8.1 (Appearance)	-
8.2 (Ageing and Accuracy- Ref IS 6274 : 1971)	-
8.3-a (lnfluence of Immersion Time)	-
8.3-b (lnfluence of Immersion Time)	-

-
-

Bureau of Indian Standards

The National Standards Body of India

BIS, Central Laboratory (CL)

20/9, Site 4, Sahibabad Industrial Area, Sahibabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201010

- sample@bis.gov.in

Scope List