BIS - LIMS (Laboratory Information Management System)

BIS, Central Laboratory (CL)

20/9, Site 4, Sahibabad Industrial Area, Sahibabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201010

- sample@bis.gov.in

Scope List

Reset

998 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

811

IS 7466 (1994)

Rubber gaskets for pressure cookers - Specifications (First Revison)

Rs.9480/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2 (Workmanship and Finish )	-
3.4-Table 1(i) (Requirements of Rubber Used for Gaskets-Hardness IRHD)	-
3.4-Table 1(ii) (Requirements of Rubber Used for Gaskets-Tensile strength,)	-
3.4-Table 1(iii) (Requirements of Rubber Used for Gaskets-Elongation at break)	-
3.4-Table 1(iv-a) (Requirements of Rubber Used for Gaskets-Hardness IRHD(After ageing 3 days in Aie-oven Change From Original Value))	-
3.4-Table 1(iv-b) (Requirements of Rubber Used for Gaskets-Tensile strength(After ageing 3 days in Aie-oven Change From Original Value))	-
3.4-Table 1(iv-c) (Requirements of Rubber Used for Gaskets-Elongation at break(After ageing 3 days in Aie-oven Change From Original Value))	-
3.4-Table 1(v-a) (Requirements of Rubber Used for Gaskets-Hardness IRHD(After ageing in an autoclave Change From Original Value))	-
3.4-Table 1(v-b) (Requirements of Rubber Used for Gaskets-Tensile strength(After ageing in an autoclave Change From Original Value))	-
3.4-Table 1(v-c) (Requirements of Rubber Used for Gaskets-Elongation at break(After ageing in an autoclave Change From Original Value))	-
3.5-ANNEX C (PERFORMANCE TEST FOR PRESSURE COOKER )	-
3.4-Table 1(vi) (Compression set)	-

-
-

812

IS 6528 (1995)

Stainless steel wire - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Table 7 (Workmanship)	-
Cl 6 (Workmanship)	-
Cl 9.1 & Table 3 (Diameter & Out Of Round)	-
Cl 10 (UTM)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Carbon)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Sulphor)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Phosphorous)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Manganese)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Silicon)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Aluminium)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Chromium)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Nickel)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Molybdenum)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Copper)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Boron)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Vanadium)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Titanium)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Nitrogen)	-

-
excluding Sample size shall be minimum dia> 3mm and thickness > 0.8 mm;

813

IS 8521 : Part 1 (1977)

Specification for industrial safety face shields: Part 1 with plastics visor

3750/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 3 (General requirements & Specific requirements)	-
Cl 4 (Visual and Dimensional Examination & Physical Requirements (Impact Resistance, Penetration Resistance, Visible Transmittance, Flammability & Disinfection))	-

-
-

814

IS 15834 (2008)

Stainless Steel Sliding Door Bolts For Use With Padlocks -specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 4.2 (Carbon Content)	-
Clause 4.2 (Silicon)	-
Clause 4.2 (Manganese)	-
Clause 4.2 (nickel)	-
Clause 4.2 (Chromium)	-
Clause 4.2 (Sulphur)	-
Clause 4.2 (Phosphorus)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm;

815

IS 12681 (1989)

Sodium nitrate for explosives and pyrotechnic industry - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 2.2, Table-1, Sr.no. 1 (Assay,)	-
Cl. 2.2, Table-1, Sr.no. 2 (Moisture and volatile matter )	-
Cl. 2.2, Table-1, Sr.no. 3 (matter insoluble in water)	-
Cl. 2.2, Table-1, Sr.no. 4 (Nitrites (as NaNO2))	-
Cl. 2.2, Table-1, Sr.no. 5 (Chlorides (as NaCl))	-
Cl. 2.2, Table-1, Sr.no. 6 (Sulphates( as Na2SO4))	-
Cl. 2.2, Table-1, Sr.no. 7 (Chlorates)	-
Cl. 2.2, Table-1, Sr.no. 9 (Iodates(NaIO4))	-
Cl. 2.2, Table-1, Sr.no. 10 (Total calcium and magnesium or compounds of these metals calculated as oxides.)	-
Cl. 2.2, Table-1, Sr.no. 11 (Ammonium compounds (as NH4NO3))	-
Cl. 2.2, Table-1, Sr.no. 12 (pH of 10 percent solution)	-
Cl. 2.2, Table-1, Sr.no. 1 (Assay,)	-
Cl. 2.2, Table-1, Sr.no. 2 (Moisture and volatile matter )	-
Cl. 2.2, Table-1, Sr.no. 3 (matter insoluble in water)	-
Cl. 2.2, Table-1, Sr.no. 4 (Nitrites (as NaNO2))	-
Cl. 2.2, Table-1, Sr.no. 5 (Chlorides (as NaCl))	-
Cl. 2.2, Table-1, Sr.no. 6 (Sulphates( as Na2SO4))	-
Cl. 2.2, Table-1, Sr.no. 7 (Chlorates)	-
Cl. 2.2, Table-1, Sr.no. 9 (Iodates(NaIO4))	-
Cl. 2.2, Table-1, Sr.no. 10 (Total calcium and magnesium or compounds of these metals calculated as oxides.)	-
Cl. 2.2, Table-1, Sr.no. 11 (Ammonium compounds (as NH4NO3))	-
Cl. 2.2, Table-1, Sr.no. 12 (pH of 10 percent solution)	-

-
-

816

IS 7098 : Part 1 (1988)

Specification for crosslinked polyethylene insulated pvc sheathed cables: Part 1 for working voltages up to and including 1100 volts (First Revision)

26250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3 (CONDUCTOR: MATERIALS)	-
4 (INSULATION : MATERIALS)	-
5.1 (FILLER AND INNER SHEATH)	-
5.2 (FILLER AND INNER SHEATH)	-
6 (ARMOURING)	-
7 (OUTER SHEATH)	-
8.1 (CONDUCTOR: CONSTRUCTION)	-
8.2 (PROTECTIVE BARRIER)	-
8.3 (SIZE OF NEUTRAL CONDUCTOR)	-
9.1 (Insulation Applied by extrusicn)	-
9.2 (Thickness of Insulation - Average)	-
9.3 (Thickness of Insulation - Minimum)	-
9.2 (Thickness of Insulation - Average)	-
9.3 (Thickness of Insulation - Minimum)	-
9.4 (Application of Insulation)	-
10.1 (Core Identification)	-
10.2 (Core Identification- Neutral)	-
10.3 (Core Identification by number )	-
10.4 (Core Identification by number - Neutral )	-
11 (LAVING UP OF CORES)	-
12.1 & 12.2 (Inner sheath : Application)	-
12.3 (Thickness of Inner Sheath)	-
13.1 (Armouring: Application)	-
13.1.2 (Armouring: Coverage )	-
13.1.3 (Armouring: Direction of Lay )	-
13.2 (Type of armour )	-
13.3 (Armouring : Dimensions -Wire Diameter)	-
13.3 (Armouring : Dimensions -Formed wire )	-
13.4 (Armour: Joint)	-
13.5 (Armouring : Resistance Test)	-
13.6 a) (ARMOURING: Tensile Strength)	-
13.6 b) (ARMOURING: Elongation )	-
13.6 c) (ARMOURING: Torsion Test (For round wire ) )	-
13.6 d) (ARMOURING: Winding Test(For formed wire))	-
13.6 e) (ARMOURING: Uniformity of zinc coating)	-
13.6 f) (ARMOURING: Mass of zinc coating )	-
13.6 g) (ARMOURING: Resistivity)	-
14.1 (Outer Sheath : Application)	-
14.2 (Colour of outer sheath)	-
14.3 (Thickness of outer sheath - AVERAGE)	-
14.3 (Thickness of outer sheath - minimum)	-
15.1 a) i) (Annealing Test ( For copper wire ) )	-
15.1 a) ii) (Tensile test (for aluminium) - Before stranding )	-
15.1 a) ii) (Tensile test (for aluminium) - After stranding )	-
15.1 a) iii) (Wrapping test (for aluminium))	-
15.1 a) iv) (Resistance test - Main conductor)	-
15.1 a) iv) (Resistance test - Neutral conductor)	-
15.1 d) i) (Phyaical tests for insulation : Tensile Test)	-
15.1 d) i) (Phyaical tests for insulation : Elongation)	-
15.1 d) ii) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-
15.1 d) ii) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-
15.1 d) iii) (Phyaical tests for insulation : Hot set )	-
15.1 d) iii) (Phyaical tests for insulation : Permanent set )	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage )	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage - Crack observed )	-
15.1 d) v) (Insulation: Waterabsorption(gravimetric))	-
15.1 e) i) (Physical tests for outer sheath : Tensile stregth)	-
15.1 e) i) (Physical tests for outer sheath : Elongation)	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation )	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-
15.1 e) iii) (Sheath: Loss of mass in air oven)	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage )	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage - Crack observed )	-
15.1 e) v) (Sheath : Hot deformation)	-
15.1 e) vi) (Sheath : Heat shock test)	-
15.1 e) vii) (Sheath : Thermalstability)	-
15.1 f) (INSULATION RESISTANCE TEST : Volume resistivity )	-
16.2 (HIGH VOLTAGE TEST )	-
16.3 (FLAMMABILITY TEST : Period of Burning )	-
16.3 (FLAMMABILITY TEST : Unaffected length )	-
17.1 (Manufacturer'. identification)	-
17.2 (cable Indentification )	-
Cl.8 (Conductor)	-
Cl.8 (Conductor)	-
Cl.8 (Conductor)	-
Cl.15.4 (Cold Bend Test (for outer sheath))	-
Cl.15.4 (Cold Impact Test (For outer sheath))	-
Cl.13.5.1 and Table 7 (Resistance Test for Armouring (other than mining Cables))	-

-
TF not available Cat C1 & C2

817

IS 12817 (2013)

Stainless steel butt hinges - Specification (Second Revision)

Rs. 2400/- and testing charges as per referred Iss View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.2, Table 1 to 6 (Length , A -IS 12817)	-
6.2, Table 1 to 6 (Breadth, B-IS 12817)	-
6.2, Table 1 to 6 (Thickness of flap, C-IS 12817)	-
6.2, Table 1 to 6 (Dia. of Hinge pin, D-IS 12817 )	-
6.2, Table 1 to 6 (Number of Knuckles- IS 12817 )	-
6.2, Table 1 to 6 (Number of Screw Holes -IS 12817 )	-
6.2, Table 1 to 6 (Holes for Screw Number- IS 12817 )	-
7.1 (General - IS 12817 )	-
7.2 (Knuckles - IS 12817 )	-
7.3 (Pins- IS 12817 )	-
7.4 (Screw Holes- IS 12817 )	-
7.4.2 (Position of screw holes - IS 12817 )	-
7.4.2, Fig 1 (The distance of the screw holes from the end of the flap - IS 12817 )	-
8 (Finish - IS 12817 )	-

-
-

818

IS 3055 : Part 1 (1994)

Clinical thermometers: Part 1 solid stem type - Specification (Second Revision)

Rs 5400.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (TEMPERATURE SCALE)	-
5.2 (TEMPERATURE SCALE)	-
7.1 (Patterns)	-
7.3 (Stem Classification )	-
7.3.1 (Stem)	-
7.3.1.1 (Stem)	-
7.3.2 (Maximum Indicating Device (Constriction))	-
7.3.2.1 (HARDNESS O F MAXIMUM INDICATING DEVICE)	-
7.3.3 (Loactor)	-
7.3.4 (Bulb)	-
7.3.4.1 (Bulb)	-
7.3.4.2 (Bulb)	-
7.3.5 (The bulb, capillary tube and mercury)	-
7.4 - Table 1-i (Scale range)	-
7.4 - Table 1-ii (Scale range)	-
7.4 - Table 1-iii (Smallest scale division)	-
7.4 - Table 1-iv (Smallest scale division)	-
7.4 - Table 1-v (Overall length)	-
7.4 - Table 1-vi (Scale length)	-
7.4 - Table 1-vii (Thickness of stem)	-
7.4 - Table 1-viii-a (Bulb length -Oral thermometer )	-
7.4 - Table 1-viii-b (Bulb length - Rectal thermometer)	-
7.4 - Table 1-ix-a (External dia of bulb -Oral thermometer )	-
7.4 - Table 1-ix-b (External dia of bulb - Rectal thermometer)	-
7.4 - Table 1-x (Distance from top of the constriction to the 35.5°C mark)	-
7.4 - Table 1-xi (Distance from the highest graduation line to top of the stem)	-
7.4 - Table 1-xii (Scale spacing)	-
7.5.1 (Graduation and Numbering)	-
7.5.2 (Graduation and Numbering)	-
7.5.3 (Graduation and Numbering)	-
7.5.4-a (Graduation and Numbering)	-
7.5.4-b (Graduation and Numbering)	-
7.5.4-c (Graduation and Numbering)	-
7.5.5 (Graduation and Numbering)	-
7.5.6 (Graduation and Numbering)	-
7.5.7 (Graduation and Numbering)	-
7.5.8 (Graduation and Numbering)	-
8.1 (Appearance)	-
8.2 (Ageing and Accuracy- Ref IS 6274 : 1971)	-
8.3-a (lnfluence of Immersion Time)	-
8.3-b (lnfluence of Immersion Time)	-

-
-

819

IS 3390 (1988)

Specification for sphygmomanometers, mercurial (Second Revision)

Rs 7800.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1.1 ( Types )	-
3.1.2 (Fastening)	-
3.1.3 (Scale Range )	-
4.1 (Metal Parts)	-
4.2 (Rubber Parts -Inflation Bulb)	-
4.2 (Rubber Parts:- Rubber Tubing BEFORE AGEING)	-
4.2 (Rubber Parts:- Rubber Tubing BEFORE AGEING)	-
4.2 (Rubber Parts:- Rubber Tubing AFTER AGEING)	-
4.2 (Rubber Parts:- Rubber Tubing AFTER AGEING)	-
4.3 (Glass Parts)	-
4.4 (Plastics)	-
4.5 (Fabric)	-
4.6 (Sewing Thread)	-
4.7 (Mercury)	-
4.8.1 (Component Part)	-
4.8.2 (Component Part)	-
4.8.2.1 (Cuff Dimension & fig 1)	-
Cl. 4.8.3, (Inflating Bag)	-
4.8.4 (Tubing)	-
4.8.5 (Inflating Bulb)	-
4.9.2 (Tube Mounting and Fittings)	-
4.9.1 (Pressure Measuring Device)	-
4.9.3 (Reservoir and Connecting Tube)	-
4.9.4 (Extension Tube)	-
4.1 (Housing)	-
4.11 (Accessories)	-
4.13 (Leakage)	-
5 (WORKMANSHIP AND FINISH)	-

-
-

820

IS 14807 (2000)

Phosphate solubilising bacterial inoculant (PSBI) - Specification

Rs.8740/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
CL 4.4 (pH)	-
CL 4.1 (Phosphate Solubilising Bacterial cells)	-
CL 4.2 (Color)	-
CL 4.3 (Dilution)	-
CL 4.5 (Phosphate solubilising)	-

-
-

821

IS 16892 (2018)

Sattu - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.7-Table 1- vii (Total bacterial count (Special Grade)- IS 5402)	-
4.7-Table 1- vii (Total bacterial count, (Standard Grade) - IS 5402)	-
4.7-Table 1- vii (Total bacterial count, (General Grade) - IS 5402)	-
4.7-Table 1- vii (Total bacterial count (Special Grade)- IS 5402)	-

-
-

822

IS 798 (2020)

Orthophosphoric Acid — Specification ( Third Revision )

Rs.14822/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Description)	-
5.2.2 Table 1 (i) (Relative density )	-
5.2.2 Table 1 (ii) (Orthophosphoric acid (H3 PO4 ))	-
5.2.2 Table 1 (iii) (Iron (as Fe), )	-
5.2.2 Table 1 (iv) (Chlorides (as Cl), )	-
5.2.2 Table 1 (v) (Sulphates (as SO4 ), )	-
5.2.2 Table 1 (vi) (Arsenic (as As2 O3 ), )	-
5.2.2 Table 1 (vii) (Antimony (as Sb2 O3 ), )	-
5.2.2 Table 1 (viii) (Nitrates (as NO3 ),)	-
5.2.2 Table 1 (ix) (Lead (as Pb), parts per million, Max)	-
5.2.2 Table 1 (x) (Silica (as SiO2 ), )	-
5.2.2 Table 1 (xi) (Calcium (as Ca) and Magnesium (as Mg), )	-
5.2.2 Table 1 (xii) (Oxygen absorbed (as O),)	-
5.2.2 Table 1 (xiii) (Volatile acids)	-
5.2.2 Table 1 (xiv) (Manganese (as Mn), )	-
5.2.2 Table 1 (xv) (Molybdenum (as Mo), )	-
5.2.2 Table 1 (xvi) (Mercury (as Hg), )	-
5.2.2 Table 1 (xvii) (Aluminium (as Al), )	-

-
-

823

IS 797 (1982)

Specification for common salt for chemical industries (Third Revision)

- View breakup
TESTING CHARGES FOR IS 797:1982-COMMON SALT FOR CHEMICAL INDUSTRIES Testing charges per man-hour=Rs 300 Power consumption per unit =Rs 9 Total testing charges for Grade 1 =11.75 x 300 + 27 x 9 + 400.00 = Rs 4168.00 (Rounded off to Rs.4200.00 ) Total testing charges for Grade 2 =14.75 x 300 + 34 x 9 + 475.00 = Rs 5206.00 (Rounded off to Rs.5200.00 ) except Additional requirements (Cl. 3.3.1.2 a), b) & c) tests.

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.3.1 (Description)	-
Cl.3.2.1 (Moisture Content For Grade 1 material (Annex A2))	-
Cl.3.2.2 (Moisture Content For Grade 2 material (Annex A2))	-
Table 1 Cl.3.3 (Sodium Chloride (as NaCl) For Grade 1 material (Annex A3))	-
Table 1 Cl.3.3 (Sodium Chloride (as NaCl) For Grade 2 material (Annex A3))	-
Table 1 Cl.3.3 (Material insoluble in water For Grade 1 material (Annex A4))	-
Table 1 Cl.3.3 (Material insoluble in water For Grade 2 material (Annex A4))	-
Table 1 Cl.3.3 (Calcium salts (as Ca) For Grade 1 material (Annex A5))	-
Table 1 Cl.3.3 (Calcium salts (as Ca) For Grade 2 material (Annex A5))	-
Table 1 Cl.3.3 (Magnasium salts (as Mg) For Grade 1 material (Annex A5))	-
Table 1 Cl.3.3 (Magnasium salts (as Mg) For Grade 2 material (Annex A5))	-
Table 1 Cl.3.3 (Sulphates (as SO4) For Grade 1 material (Annex A6))	-
Table 1 Cl.3.3 (Sulphates (as SO4) For Grade 2 material (Annex A6))	-
Table 1 Cl.3.3 (Iron compound (as Fe) For Grade 1 material (Annex A7))	-
Table 1 Cl.3.3 (Iron compound (as Fe) For Grade 2 material (Annex A7))	-

-
500 gm x 3

824

IS 1239 : Part 1 (2004)

Steel tubes, tubulars and other wrought steel fittings - Specification: Part 1 steel tubes (Sixth Revision)

Rs. 9200/- Excluding test on joints View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (Outer Diameter, Thickness & Mass)	-
Cl 10.1.1 (Manufacturing )	-
Cl 12 (Workmanship)	-
Cl 14 (Tensile Test, Flattening Test & Bend Test)	-
Cl 15 (Workmanship)	-
7, 6.1.1 (CARBON)	-
7, 6.1.1 (SULPHUR)	-
7, 6.1.1 (PHOSPHURS)	-
7, 6.1.1 (MANGANESE)	-
7, 6.1.1 (SILICON)	-
7, 6.1.1 (ALUMINIUM)	-
7, 6.1.1 (NITROGEN)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm; Excluding "-; i) Joint (Cl 10.1) , ii) Leak Proof Test (Cl 13)"

825

IS 1785 : Part 2 (1983)

Specification for plain hard drawn steel wire for prestressed concrete: Part 2 as - Drawn wire (First Revision)

Rs 3000/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5.1 (Diameter)	-
Cl 5.1.2 (Weight)	-
Cl 6.1 (Tensile Test On UTM)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm; Excluding -; Relaxation (Cl 6.5), Proof Stress (Cl 6.2)

826

IS 11785 (1986)

Specification for captan (Wettable Powder) WP

Rs 3650.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.1 (Description)	-
2.3 Table 2 i (Captan content)	-
2.3 Table 2 ii (Sieving requirement)	-
2.3 Table 2 iii (Suspensibility)	-
2.3 Table 2 iv (Wettability)	-
2.3 Table 2 v (Acidity/Alkalinity)	-

-
-

827

IS 1785 : Part 1 (1983)

Specification for plain hard - Drawn steel wire for prestressed concrete: Part 1 cold drawn stress - Relieved wire (Second Revision)

Rs. 27300.00 (Complete testing charges) Rs. 9300.00 (F View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5.1 (Diameter)	-
Cl 6.1 (Tensile Test On UTM)	-
Cl 6.3 (Reverse Bend Test)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm; Excluding -; Relaxation (Cl 6.5), Proof Stress (Cl 6.2)

828

IS 11010 (1984)

Specification for ziram colloidal suspension

Rs.3500.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.1 (Description)	-
2.2 Table 2 i (Ziram content)	-
2.2 Table 2 iv (pH of suspension at 27°C)	-
2.2 Table 2 iii (Colloidal content)	-
2.2 Table 2 iv (pH of suspension at 27°C)	-

-
-

829

IS 2879 (1998)

Mild steel for metal arc welding electrodes - Specification (Third Revision)

Testing charges are Rs.9050/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 7 (Workmanship)	-
Cl 8 & 9 (Diameter)	-
6 (Carbon %)	-
6 (Manganese %)	-
6 (Phosphorus %)	-
6 (Sulphur %)	-
6 (Silicon %)	-
6 ( Copper %)	-
6 ( Aluminium %)	-
6 ( Nb)	-
6 (V)	-
6 ( Ti)	-
6 (Cr)	-
6 (Mo)	-
6 (Ni)	-
6 (Cr+ Mo+ Ni)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm;

830

IS 4270 (2001)

Steel tubes used for water wells specification (Third Revision)

Rs.7500/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 6 (Tensile Test & Flattening Test)	-
Cl 7 (Outer Diameter, Thickness, Mass & Straightness)	-
Cl 9 (Pipe ends, Angle of bevel & Root Face )	-
Cl 10 (Outer Diameter & Overall Length)	-
Cl 12 (Bituminous Coating & Galvanizing )	-
Cl 14 (Workmanship)	-
5.2 (sulphur)	-
5.2 (phosphorus)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm; Excluding -; Hydrostatic test (Cl 8)

831

IS 7887 (1992)

Mild steel wire rod for general engineering purposes - Specification (First Revision)

Rs.7200/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (Workmanship)	-
Cl 9 (Nominal Diameter & Out Of Shape)	-
6.1 (Carbon %)	-
6.1 (Sulphur %)	-
6.1 (Phosphorus %)	-
6.1 (Manganese %)	-
6.1 (Silicon %)	-
6.1 ( Aluminium %)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm;

832

IS 6913 (1973)

Specification for stainless steel tubes for the food and beverage industry

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 5.1, Table 1 (Carbon )	-
Cl. 5.1, Table 1 (Sulphur)	-
Cl. 5.1, Table 1 (Phosphorus)	-
Cl. 5.1, Table 1 (Manganese)	-
Cl. 5.1, Table 1 (Nickel)	-
Cl. 5.1, Table 1 (Chromium)	-
Cl. 5.1, Table 1 (Molybdenum)	-

-
Steel grade designation as per Table 2 may be declared. Sample 5x5 cm having size dia> 3mm and thickness> 0.8 mm.; Excluding Except corrosion test;

833

IS 10748 (2004)

Hot - Rolled steel strip for welded tubes and pipes - Specification (Second Revision)

Please see remarks View breakup
Testing charges per man-hour Rs.300.00 Electricity power consumption Rs.9.00 per KWH Hence complete testing charges for the product are as follows: i) For grade 1,2&3 = 3716 /-, Rounded off to Rs.3750/- ii) For grade 4,5 & 6 including Micro alloying elements = 6728/-, Rounded off to Rs.6750/- Remarks: Testing chargesfor each of the elements other than Table-1 (Silicon, Aluminum, Nitrogen etc.) will be Rs.1004/- CA may kindly approve.

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 & Table 3 (UTM)	-
Cl 9 (Press)	-
Cl 11 (Workmanship)	-
Cl 12 & 13 (Length, Width & Thickness)	-
7.1 (Carbon %)	-
7.1 (Sulphur %)	-
7.1 (Phosphorus %)	-
7.1 (Manganese %)	-
7.1 (Silicon %)	-
7.1 ( Aluminium %)	-
7.1 ( Nitrogen%)	-
7.1 ( Copper %)	-
7.1 ( Nb)	-
7.1 (V)	-
7.1 ( Ti)	-
7.1 (Cr)	-
7.1 (Mo)	-
7.1 (Ni)	-
7.1 (CE)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm;

834

IS 6902 (1973)

Specification for steel wire for spokes

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 4.1 (Carbon- IS 228)	-
Cl. 4.1 (Manganese- IS 228.)	-
Cl. 4.1 (Sulphur- IS 228.)	-
Cl. 4.1 (Phosphorus- IS 228.)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm;

835

IS 6649 (1985)

Specification for hardened and tempered washers for high strength structural bolts and nuts (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5 (Chemical Composition- Sulphur)	-
5 (Chemical Composition- Phosphorus)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm;

836

IS 6603 (2001)

Stainless steel bars and flats - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1 (Carbon -Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1 (Sulphur- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1 (Phosphorus- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1 (Manganese- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1 (Silicon- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1 (Nickel -Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1 (Chromium- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1 (Molybdenum- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1 (Titanium- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1 (Niobium- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1 (Others (Nitrogen)- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-
6 (Freedom from defects:)	-
9.1, Table 3 (0.2 Percent Proof Stress, MPa)	-
9.2, Table 3 (Tensile Strength, MPa)	-
9.3, Table 3 (Elongation ,Percent)	-
9.4, Table 3 (Annealed Hardness, HB-IS 1500: Pt 1)	-
9.5, Table 3 (Charpy Impact Test, J-IS 1499)	-
12 (Dimensions & Tolerances, mm-IS 6603)	-
12 (Diameter, mm)	-
12 (Out of Round , mm)	-
12 (Length , mm)	-
12 (Variation in Straightness)	-
Cl. 12 Table 9, 11 & 13 (Square Size)	-
Cl. 12 Table 11,13 & 14 (Thickness of Flat)	-
Cl. 12 Table 11,13 & 14 (Width of Flat)	-
Cl. 12 Table 10 & 13 (Hexagonal Size)	-
Cl. 12 Table 9 (Out of Square)	-
Cl. 12 Table 10 (Maximum Differences in Three Measurements for Hexagons)	-
Cl. 9.3 Table 3 (Bend Test)	-

-
Steel grade designation as per Table 3 may be declared. Sample 5x5 cm having size dia> 3mm and thickness> 0.8 mm.; Excluding Except corrosion test; Proof stress test (Cl 9.1), Charpy impact test (Cl 9.5)

837

IS 15227 (2002)

Deltamethrin ULV - Specification

Rs.2150.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2.1 (Description)	-
3.2.2 (Flash Point (Abel))	-
3.3.1 (Deltamethrin Content)	-
3.3.2 (Acidity)	-

-
-

838

IS 1161 (2014)

Steel tubes for structural purposes - Specification (Fifth Revision)

5725 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 6 (Outer Diameter, Thickness & Mass)	-
Cl 7 (Workmanship)	-
Cl 8 (Workmanship)	-
Cl 9 (Workmanship)	-
Cl 11 (Tensile Test, Flattening Test & Cold Bend Test)	-
Cl 13 (Workmanship)	-
Clause - 5.1, Table-3 ( CARBON)	-
Clause - 5.1, Table-3 (SULPHUR)	-
Clause - 5.1, Table-3 (PHOSPHURS)	-
Clause - 5.1, Table-3 (MANGANESE)	-
Clause - 5.1, Table-3 ( ALUMINIUM)	-
Clause - 5.1, Table-3 (SILICON)	-
Clause - 5.1, Table-3 (NITROGEN)	-
5 AND AS PER IS 10748 (CARBON EQUIVALENT)	-
5 AND AS PER IS 10748 (MICRO ALLOY)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm;

839

IS 6529 (1996)

Stainless steel blooms, billets and slabs for forging - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1,7.2,7.3 Table 1 (Carbon-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
7.1,7.2,7.3 Table 1 (Sulphur-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
7.1,7.2,7.3 Table 1 (Phosphorous-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
7.1,7.2,7.3 Table 1 (Manganese-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
7.1,7.2,7.3 Table 1 (Others(Nitrogen)-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
7.1,7.2,7.3 Table 1 (Nickel-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
7.1,7.2,7.3 Table 1 (Chromium-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
7.1,7.2,7.3 Table 1 (Molybdenum-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
7.1,7.2,7.3 Table 1 (Titanium-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
7.1,7.2,7.3 Table 1 (Niobium-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
7.1,7.2,7.3 Table 1 (Selenium-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
7.3 (Copper-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
6 (Freedom from defects)	-
9 (Hardness)	-
10 (Dimensional Tolerances)	-

-
Steel Grade/designation as per Table 1 may be declared. Sample size shall be minimum dia> 3mm and thickness > 0.8 mm; Excluding Except corrosion test; Corrosion resistance test (Cl 13)

840

IS 6911 (2017)

Stainless steel plate, sheet and strip - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 (Freedom from defects , IS 6911)	-
10.1,Table 4&Table 6 (Tensile Test - IS 1608(Pt -1))	-
10.2,Table 4&Table 5 (Hardness Test- IS 1500(Pt -1),IS 1501 (Pt-1),IS 1586 (Pt -1))	-
10.3 (Bend Test - IS 1599)	-
11,Table 7 (Erichsen cupping test-IS 10175)	-
15 (Surface Finish)	-
17 (Dimension and tolerance)	-
Cl. 7.1 & 7.2 Table 1 (Carbon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Sulphur -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Phosphorus -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Manganese -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Silicon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Nickel -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Chromium -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Molybdenum -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Titanium-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Niobium-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Copper -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Nitrogen -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Others-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-

-
Steel Grade/designation as per Table 1 may be declared. Sample size shall be minimum dia> 3mm and thickness > 0.8 mm; Excluding Except corrosion test; Test facility is also not available for 0.2 % proof stress

Bureau of Indian Standards

The National Standards Body of India

BIS, Central Laboratory (CL)

20/9, Site 4, Sahibabad Industrial Area, Sahibabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201010

- sample@bis.gov.in

Scope List