BIS - LIMS (Laboratory Information Management System)

BIS, Central Laboratory (CL)

20/9, Site 4, Sahibabad Industrial Area, Sahibabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201010

- sample@bis.gov.in

Scope List

Reset

990 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

931

IS 1251 (1988)

Specification for zinc phosphide, technical

Technical

Rs.2300.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.1 (Description)	-
2.3 (Freedom from sulphides)	-
2.2 Table 2 i (Zinc Phosphide (Zn3P2))	-
2.2 Table 2 ii (Zinc Content)	-
2.2 Table 2 iii (Sieving Requirements: Material passing through 150 micron IS Sieve)	-
2.2 Table 2 iv (Sieving Requirements: Material passing through 106 micron IS Sieve)	-

-
-

932

IS 261 (1982)

Specification for copper sulphate (Second Revision)

please see remarks View breakup
Rs 2400/- for Tech., Rs 3900/- for Pure

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
1(i) Table 1 (Copper, Tech, A-2)	-
1(i) Table 1 (Copper, Pure, A-2)	-
1(ii) Table 1 (Matter insoluble in water, Tech, A-3)	-
1(ii) Table 1 (Matter insoluble in water, Pure, A-3)	-
1(iii) Table 1 (Soluble iron and aluminium compounds ( as Fe ), Pure, A-4)	-
1(iv) Table 1 (pH value, Tech, A-5)	-
1(iv) Table 1 (pH value, Pure, A-5)	-
1(v) Table 1 (Chloride ( as Cl ), Tech, A-6)	-
1(v) Table 1 (Chloride ( as Cl ), Pure, A-6)	-
1(vi) Table 1 (Arsenic ( as As2O3 ), Tech, A-7)	-
1(vi) Table 1 (Arsenic ( as As2O3 ), Pure, A-7)	-
1(vii) Table 1 (Lead and zinc, Tech, A-8)	-
1(vii) Table 1 (Lead and zinc, Pure, A-8)	-
Cl 3.1 (Description, Tech and Pure)	-

-
Facility is complete for this IS; Excluding NA

933

IS 1806 (2018)

Malted milk foods - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.3-Table 1- ix (Bacterial count)	-
4.3-Table 1- x (Coliform count)	-
4.3-Table 1- xi (E. coli)	-
4.3-Table 1- xii (Yeast and mould count)	-
4.3-Table 1- xiii (Salmonella)	-
4.3-Table 1- xiv (Shigella)	-
4.3-Table 1- xv (Vibrio cholerae )	-
4.3-Table 1- xv ( V. parahaemolyticus)	-
4.3-Table 1- xvi (Faecal streptococci )	-
4.3-Table 1- xvi ( Staphylococcusaureas)	-

-
-

934

IS 10758 (1983)

Specification for de - Odourizing - Cum - Disinfectant fluids

Rs.6000/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 3.1 (Description)	-
Cl. 3.2 (Volatile matter)	-
Cl. 3.3 (Stability after dilution(with artificial hard water))	-
Cl. 3.4 (Persistance of Odour)	-
Cl. 3.5 (Flash point(abel))	-
Nil (Staphylococcal coe.)	-
Cl. 3.6 / 2.1 (Germicidal Value)	-
Cl. 3.6 / 2.1 (Germicidal Value)	-
Cl. 3.6 / 2.1 (Germicidal Value)	-
Cl. 3.6 / 2.1 (Germicidal Value)	-
Cl. 3.6 / 2.1 (Germicidal Value)	-
Cl. 3.1 (Description)	-
Cl. 3.2.1 (Volatile matter (steam distillation))	-
Cl. 3.4 (Persistance of Odour)	-

-
-

935

IS 1061 (2017)

Disinfectant fluids, phenolic type - Specification (Fifth Revision)

Class Black fluid-Rs.9204. Class White fluid - Rs.10504 View breakup
Testing charges for Disinfectant Fluids, Phenolic Type as per IS 1061 : 2017, Class - Black fluid - Rs. 9204 Testing charges for Disinfectant Fluids, Phenolic Type as per IS 1061 : 2017, Class - White fluid - Rs. 10504

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2 (Stability after Dilution)	-
4.3/3.2 (Germicidal Value)	-
4.3/3.3 (Germicidal Value)	-
4.3/3.4 (Germicidal Value)	-
4.3/3.5 (Germicidal Value)	-
4.3/3.5 (Germicidal Value)	-
4.5 (Stability on Storage)	-
4.3/3.5 (Germicidal Value)	-
4.6 (Detection of Phenolic Compounds)	-
4.4 (Mercury Compounds)	-
4.1.1 (Composition and Description)	-
4.1.2 (Composition and Description)	-
4.3/3.2 (Germicidal Value)	-

-
-

936

IS 15328 (2003)

Unplasticized Non-Pressure Polyvinyl Chloride ( PVC -U ) Pipes for use in Underground Drainage and Sewerage Systems -

3450 View breakup
Rs. 3450/- excluding composition of material, ring stiffness, resistance to external blows at 0 degree C, acceptance test, type test, internal hydrostatic pressure, internal negative hydrostatic pressure (Cl. 10.1.2 & Cl. 10.2.2).

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1,6.1.1 IS 12235 (Part 1) Table 1 (Dimension of Pipes: Mean outside Diameter, dem)	-
6.1,6.1.1 IS 12235 (Part 1) Table 1 (Outside Diameter at any point, de)	-
6.1.2 IS 4985 Table 2 (Wall Thickness, e )	-
6.1.4, Table 3 (ii) Min. depth of engagement, A. )	-
6.1.4, Table 4 (ii) Length of Solvent Cement socket, l2 )	-
7.1 (Appearance:- )	-
7.2 (Colour )	-
7.3 IS 1223S ( Part 2) (Vicat Softening Temperature When determined according to IS 1223S ( Part 2), shall not be lessthan 79°C.)	-
7.4 IS 1223S ( Part 5) (Longitudinal Reversion: When tested according to the methodprescribed in IS 1223S ( Part 5), shall not exceed ± 5 percent. The pipe shall not exhibit any blisters, bubbles or crackson completion of the test.)	-

-
Excluding -Test facility not available for Cl.8.1 Resistance to external blows at 0°C, Cl.8.2 Ring Stiffness, Cl.8.3 Resistance to internal hydrostatic Pressure (Type test), Cl. 9 Joints, Cl.10.1 Elastomeric Sealing ring joints, Cl.10.2 Solvent cemented joints.;

937

IS 14333 (1996)

High Density Polyethylene Pipe For Sewerage -

3900 View breakup
Rs. 3900/- excluding raw material, anti-oxidant, hydrostatic characteristics, density and carbon black content.

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (Colour)	-
6 (Dimensions of pipes)	-
7 (Visual Appearance)	-
8.2 (Reversion)	-

-
IS superseded by newer version; Excluding oxidation induction time;

938

IS 15778 (2007)

Chlorinated polyvinyl chloride (Cpvc) pipes for potable hot and cold water distribution supplies - Specification

6375 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.3.2 IS 13360 (Part 3/See 1) (Density)	-
7.1 IS 12235 (Part 1) Table 2 (Dimension of Pipes: Mean outside Diameter)	-
7.1.2 IS 12235 (Part 1) Table 2 (Wall Thickness )	-
9.1 (Visual Appearance)	-
9.4 IS 12235(Part 5/Sec 1 and Sec 2) (Reversion Test : When tested by the method prescribed in IS 12235(Part 5/Sec 1 and Sec 2), a length of pipe 200 + 20 mm long shall not alter in length by more than 5 percent.)	-
9.5 IS 12235(Part 2) (Vicat Softening Temperature: When tested by the method prescribed in IS 12235(Part 2), the Vicat softening temperature of the specimen shall not be less than 110°C.)	-
9.6 IS 12235(Part 14) (Density)	-
10.5 IS 12235(Part 13) (Tensile Strength : When tested by the method prescribed in IS 12235(Part 13), the tensile strength at yield shall not be less than 50 MPaat 27±2°C. )	-

-
Excluding Test Facility Not avaialble for Cl 9.3 Effect on Water,Cl 10.1 Hydraulic Characterstics, Cl 10.2 Thermal Stability,Cl 10.3 Resistance to External Blow, Cl 10.4 Flattering Test.;

939

IS 781 (1984)

Specification for cast copper alloy screw down bib taps and stop valves for water services (Third Revision)

Rs.2700/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 4.1, Table-1 (Csat Brass LCB-1 of IS 292 1983,Ingots, Cu + Ni)	-
Clause 4.1, Table-1 (Cast Brass Grade DCB - 2 of IS 1264 : 1981, Die Casting, Cu)	-
Clause 4.1, Table-1 (Leaded In Tin Bronze ,LTB-2 of IS 318, Sn)	-
Clause 4.1, Table-1 (Brass, Tyape 1 half Hard of IS 319 : 2007, Grade -1 , Cu)	-
Clause 4.1, Table-1 (Grade HT 1 of IS 320 : 1980, Copper + incidental Nickel)	-
Clause 4.1, Table-1 (Grade FHTB 1 of IS 6912 : 2005, Cu)	-
Clause 4.1, Table-1 (Grade HT 1 of IS 320 : 1980, Total other elements )	-
Cl 3 (Nominal Size)	-
Cl 5 (Dimensions & Tolerances)	-
Cl 6.1 (CONSTRUCTION AND WORKMANSHIP)	-
Cl 6.3 (CONSTRUCTION AND WORKMANSHIP)	-
Cl 6.4 (CONSTRUCTION AND WORKMANSHIP)	-
Cl 6.5 (CONSTRUCTION AND WORKMANSHIP)	-
Cl 6.6 (CONSTRUCTION AND WORKMANSHIP)	-
Cl 6.7 (CONSTRUCTION AND WORKMANSHIP)	-
Cl 6.8 (CONSTRUCTION AND WORKMANSHIP)	-
Cl 6.11 (CONSTRUCTION AND WORKMANSHIP)	-
Cl 7 (MINIMUM MASS)	-
Cl 8 (Finish)	-
Cl 9 (Testing)	-

-
Material of component parts test as per table 1 may plese be declared Sample size shall be minimum dia> 3mm and thickness > 0.8 mm; Excluding all except IS 318 : 1974, IS 320 : 1980;

940

IS 8360 : Part 1 (1977)

fabricated high density polyethylene (HDPE) fittings for potable water supplies: Part 1 General requirements

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (DIMENSIONS OF FlTTINGS)	-
4.2 (DIMENSIONS OF FlTTINGS)	-

-
-

941

IS 8088 (2019)

Tricycle, hand propelled ? specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 & Table-1 (Overall length)	-
4.1 & Table-1 (Overall width)	-
4.1 & Table-1 (Overall height)	-
4.1 & Table-1 (Width of foot rest)	-
4.1 & Table-1 (Length of foot rest)	-
4.1 & Table-1 (Clearance of foot rest from ground)	-
4.1 & Table-1 (Arm rest height from seat)	-
4.1 & Table-1 (Seat length)	-
4.1 & Table-1 (Seat width)	-
4.1 & Table-1 (Back height from seat)	-
4.1 & Table-1 (Length of steering handle)	-
4.1 & Table-1 (Height of rear wheel supporting frame)	-
4.1 & Table-1 (Leverage of steering handle)	-
Cl.6.3 of IS 8088 & IS 2414 (Tyres and Tubes)	-
Cl.6.4 of IS 8088 & IS 624 (Wheel Rims)	-
6.5 (Mudguards)	-
6.6 (Brakes)	-
6.7 (Sprocket and Free Wheel)	-
6.8 (Front Wheel Hub)	-
6.9 (Rear Wheel Hub)	-
6.11 (Chain Cover)	-
6.12 (Armrests)	-
6.13 (Tool Box)	-
Cl.6.14 of IS 8088 & IS 6799 (Lock)	-
6.15 (Hood)	-
6.18 (Accessories)	-
8.1 (Road test)	-
8.2 (Manoeuvrability)	-
8.3 (Static Load Test)	-
8.5 (Test for Finish)	-
5.1 of IS 8088 & Cl.5 of IS 2039 (Carbon- Relevant parts of IS 228 or by other instrumental and chemical method)	-
5.4.2 of IS 8088 & IS 513(Part-1) (Carbon- Relevant parts of IS 228 or by other instrumental and chemical method)	-
5.4.3 of IS 8088 & IS 277 (Carbon- Relevant parts of IS 228 or by other instrumental and chemical method)	-
5.4.3 of IS 8088 & IS 513(Part-1) (Carbon- Relevant parts of IS 228 or by other instrumental and chemical method)	-
Cl.5.5 of IS 8088 & IS 4454(Part-1) (Carbon- Relevant parts of IS 228 or by other instrumental and chemical method)	-
5.1 of IS 8088 & Cl.5 of IS 2039 (Manganese- Relevant parts of IS 228 or by other instrumental and chemical method)	-

-
-

942

IS 778 (1984)

Specification for 2010 copper alloy gate, globe and check valves for waterworks purposes (Fourth Revision)

Rs 4500/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6- Table 1-i) (Brass(Body)-Cl 7 and table 1 of IS 1264)	-
6- Table 1-i) (Leaded tin Bronze(Body)-Cl 3 and table 1 of IS 318)	-
6- Table 1-ii) (Forged Brass(Bonnet or cover)-Cl 8 , table 3 and FLB of IS 6912)	-
6- Table 1-iv) (High-tensile brass( stem) - Cl 4.1 and table 1 of IS 320)	-
4 (Classification )	-
7.1.4.1- Table 3 (Diameter of flange - IS 778)	-
7.1.4.1- Table 3 (Thickness of flange - IS 778)	-
7.1.4.1- Table 3 (Diameter of Belt circle -IS 778)	-
7.1.4.1- Table 3 (No. of holes - IS 778)	-
7.1.4.1- Table 3 (Diameter of holes -IS 778)	-
7.2.2 (Bonnet Flanges - IS 778)	-
7.1.3.1 (Screwed Body End -IS 778)	-

-
complete

943

IS 1580 (1991)

Bituminous compounds for waterproofing and caulking purposes - Specification (Second Revision)

Rs. 2172/ View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 4.2.2 and 5 (water content)	-
Clause 4.2.2 and 5 (ash content)	-
Clause 4.2.2 and 5 (water content)	-
4.2 (Composition)	-
Clause 4.2.2 , Table 1,(iii) (Flow Test)	-
Clause 4.2.2 , Table 1,(iv) (Flash point ,degree celsius, Min)	-
Clause 4.2.2 , Table 1,(v) (Flexibility and adhesion)	-
Clause 4.2.2 , Table 1,(vi) a (Consistency a) Before setting ( test after 1 h ) Min)	-
Clause 4.2.2 , Table 1,(vi) b (Consistency b) After setting ( test after 24 h ) Min)	-
Clause 4.2.1 (Composition)	-
Clause 4.2.2 , Table 1,(i) (Water content, percent by mass, Max)	-
Clause 4.2.2 , Table 1,(ii) (Ash content, percent by mass, Max)	-
Clause 4.2.2 , Table 1,(iv) (Flash point ,degree celsius, Min)	-
Clause 4.2.2 , Table 1,(iii) (Flow Test)	-
Clause 4.2.2 , Table 1,(v) (Flexibility and adhesion)	-
Clause 4.2.2 , Table 1,(vi) a (Consistency a) Before setting ( test after 1 h ) Min)	-
Clause 4.2.2 , Table 1,(vi) b (Consistency b) After setting ( test after 24 h ) Min)	-
4.3 (Keeping Quality)	-
Clause 4.2.2 , Table 1,(ii) (Ash content, percent by mass, Max)	-
Clause 4.2.2 , Table 1,(i) (Water content, percent by mass, Max)	-
Clause 4.2.1 (Composition)	-
Clause 4.2.2 , Table 1,(iii) (Flow Test)	-
Clause 4.2.2 , Table 1,(iv) (Flash point ,degree celsius, Min)	-
Clause 4.2.2 , Table 1,(v) (Flexibility and adhesion)	-
Clause 4.2.2 , Table 1,(vi) a (Consistency a) Before setting ( test after 1 h ) Min)	-
Clause 4.2.2 , Table 1,(vi) b (Consistency b) After setting ( test after 24 h ) Min)	-
Clause 4.2.1 (Composition)	-
Clause 4.2.2 , Table 1,(iii) (Flow Test)	-
Clause 4.2.2 , Table 1,(iv) (Flash point ,degree celsius, Min)	-
Clause 4.2.2 , Table 1,(v) (Flexibility and adhesion)	-
Clause 4.2.2 , Table 1,(vi) a (Consistency a) Before setting ( test after 1 h ) Min)	-
Clause 4.2.2 , Table 1,(vi) b (Consistency b) After setting ( test after 24 h ) Min)	-

-
-

944

IS 738 (1994)

Wrought aluminium alloys, drawn tube for general engineering purposes - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 8.1, Table 1 (Aluminium- IS 504 : 1963 or 1S 11085 : 1984 or any other established instrumental/chemical method. )	-
Cl. 8.1, Table 1 (Copper- IS 504 : 1963 or 1S 11085 : 1984 or any other established instrumental/chemical method. )	-
Cl. 8.1, Table 1 (Silicon- IS 504 : 1963 or 1S 11085 : 1984 or any other established instrumental/chemical method. )	-
Cl. 8.1, Table 1 (Zinc- IS 504 : 1963 or 1S 11085 : 1984 or any other established instrumental/chemical method. )	-
Cl. 8.1, Table 1 (Iron- IS 504 : 1963 or 1S 11085 : 1984 or any other established instrumental/chemical method. )	-

-
Grade as per Table 1 IS 738 may please declared. Sample size shall be minimum dia> 3mm and thickness > 0.8 mm;

945

IS 164 (2015)

Ready mixed paint for road marking - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5.5, Table 1, S.no. x) (Flash point )	-
5.1 (Composition)	-
5.2 (Application)	-
Cl 5.3 (Durability)	-
Cl. 5.4 (Lead Restriction)	-
Cl 5.5, Table 1, S.no. i) (Drying time, a) Surface dry)	-
Cl 5.5, Table 1, S.no. i) (Drying time, b) Hard dry)	-
Cl 5.5, Table 1, S.no. ii) (Consistency)	-
Cl 5.5, Table 1, S.no. iii) (Finish)	-
Cl 5.5, Table 1, S.no. iv) (Colour)	-
Cl 5.5, Table 1, S.no. v) (Wet opacity)	-
Cl 5.5, Table 1, S.no. vi) (Resistance to bleeding)	-
Cl 5.5, Table 1, S.no. vii) (Recoating property)	-
Cl 5.5, Table 1, S.no. viii) (Resistance to wear: a) For Grade 1)	-
Cl 5.5, Table 1, S.no. viii) (Resistance to wear: a) For Grade 2)	-
Cl 5.5, Table 1, S.no. ix) (Residue on sieve)	-
Cl 5.5, Table 1, S.no. xi) (xi) Mass)	-
Cl 5.6 & Cl 5.6.2.1 (Optional Requirement for ECO-Mark, volatile organic compounds,)	-
5.6.2.2 (Optional Requirement for ECO-Marktoxic metals such as cadmium, chromium (VI) and their compounds)	-

-
IS is withdrawn. Revisied 2023 version is now available.;

946

IS 13334 : Part 2 (2014)

Skimmed milk powder - Specification: Part 2 extra grade (First Revision)

Rs 10430/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Table 1 (ix) (Bacterial count (IS 5402))	-
Table 1 (x) (Coliform count (IS 5401 - Part 1))	-
Table 1 (xi) (Escherichia coli (IS 5887 - Part 1))	-
Table 1 (xii) (Coagulase positive Staphylococcus aureus (IS 5887 - Part 2))	-
Table 1 (xiii) (Salmonella (IS 5887 - Part 3))	-
Table 1 (xiv)(a) (Spore Count: a)Aerobic (Bacillus cereus) Type m (IS 5887 - Part 6))	-
Table 1 (xiv)(b) (Spore Count: b) Anaerobic (Sulfite reducing Clostridia) Type m (ISO 15213 : 2003))	-
Table 1 (xiv)(b) (Spore Count: b) Anaerobic (Sulfite reducing Clostridia) Type M (ISO 15213 : 2003))	-
Table 1 (xiv)(b) (Spore Count: b) Anaerobic (Sulfite reducing Clostridia) Type m (ISO 15213 : 2003))	-
Table 1 (xv) (Listeria monocytogenes (IS 14988 - Part 2 : 2001))	-
Table 1 (i) (Moisture (IS 116231or 16072))	-
Table 1 (ii) (Milk protein in milk solids not fat (IS 72192))	-
Table 1 (iii) (Milk fat (IS 117213) or Annex B)	-
Table 1 (viii) (Scorched particles (equivalent to Disc B) (IS 13500))	-
Table 1 (vii) (Lactate content (IS 11202))	-
Table 1 (v) (Total ash (on dry basis), Annex B of IS 14433)	-
Table 1 (iv) (Insolubility index (IS 12759))	-
Table 1 (vii) (Lactate content (IS 11202))	-
Table 1 (xv) (Listeria monocytogenes (IS 14988 - Part 2 : 2001))	-

-
500 gm x 3

947

IS 4246 (2002)

Domestic gas stoves for use with liquefied petroleum gases - Specification (Fifth Revision)

Please see remarks View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.24(Annexure E) (on no account the carbon monoxidel carbon dioxide ratio of the exhaust gases of any burner. operating at any consumption at which the burner is stable at gas inlet pressure from 2452 kN/m2 to 3432 kN/m2 (25 gf/cm2 to 35 gf/cm2), exceed 0.02.)	-
Cl.23 (There shall be no extinction of the flames on any of the burners operating at maximum consumption when the appliance is placed in a general (not localized) current of air with a velocity of 2 m/s, as measured with a rotating vane anemometer. The location of the appliance relative to neighboring walls and the direction of the draught shall be varied to correspond to likely conditions of appliance installation. This applies for all pressures from 2452 kN/m2 to 3432 kN/m2 (25 gf/cm2 to 35 gf/cm2).)	-
24 (Annex - E) (Combustion (CO and CO2 ratio))	-
4.1 (Requirement)	-
5 (Materials)	-
6 (Design for Maintenance)	-
7 (Rigidity and Stability)	-
8 (Workmanship and Finish)	-
9 (Gas Taps)	-
10 (Injector Jets)	-
11 (Burners)	-
13.1 (Gas Soundness)	-
13.2 (Gas Leak Detector)	-
14 (Gas Inlet Connections)	-
15 (Strength and Rigidity)	-
16 (General Conditions of Test)	-
17.1.1 (Gas Consumption)	-
18 (Ignition and Flame Travel)	-
19 (Flame Stability)	-
20 (Noise Control)	-
21 (Flash Back)	-
22 (Formation of Soot)	-
23 (Resistance to Draught)	-
24 (Combustion)	-
25 (Fire Hazard and Limiting Temperature)	-
26 (Thermal Efficiency)	-
27.1 (Type Tests)	-
27.2 (Routine Tests)	-
29 (Marking)	-
30 (Packing)	-
5.1.2 (Toughened glass- Adhesive tape)	-
5.1.3 (Thermal Shock test)	-

-
-

948

IS 733 (1983)

Specification for wrought aluminium and aluminium alloy bars, rods and sections (For General Engineering Purposes) (Third Revision)

please see remarks View breakup
TESTING charges per man-hour are Rs. 75.00. Testing charge for physical tests are Rs. 450.00, and for Chemical tests will depend upon the elements to be tested according to the designation of the material

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Table-1, Clause - 5.1 (Copper)	-
Table-1, Clause - 5.1 (Iron)	-
Table-1, Clause - 5.1 (Magnesium)	-
Table-1, Clause - 5.1 (Manganese)	-
Table-1, Clause - 5.1 (Titanium)	-
Table-1, Clause - 5.1 (Silicon)	-
Table-1, Clause - 5.1 (Chromium)	-
Table-1, Clause - 5.1 (Zinc)	-
Cl. 4 (Freedom from Defects)	-
7 (Dimension - IS 3965)	-
Cl. 5.1, Table 2 (Tensile Strength- IS 1816)	-
Cl. 5.1, Table 2 (Elongation on 50 mm or 5.65√So Gauge Length)	-

-
-

949

IS 158 (2015)

Ready mixed paint, brushing, bituminous, black, acid, alkali and heat resisting - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 4.3, Table 1, S.no.xv) (Flash point ,)	-
4.1 (Composition)	-
4.2.1 (Lead Restriction)	-
Cl 4.3, Table 1, S.no. i) (Drying time, Hard dry)	-
Cl 4.3, Table 1, S.no. ii) (Consistency)	-
Cl 4.3, Table 1, S.no. iii) (Finish)	-
Cl 4.3, Table 1, S.no. iv) (Wet opacity)	-
Cl 4.3, Table 1, S.no. v) (Colour)	-
Cl 4.3, Table 1, S.no. vi) ( Mass)	-
Cl 4.3, Table 1, S.no.xvi) (Keeping properties)	-
Cl 4.3, Table 1, S.no.viii) (Flexibility and adhesion)	-
Cl 4.3, Table 1, S.no. ix) (Stripping test )	-
Cl 4.3, Table 1, S.no. x) (Protection against corrosion under conditions of condensation)	-
Cl 4.3, Table 1, S.no.xi) (Volatile matter, perce)	-
Cl 4.3, Table 1, S.no.xii) (Resistance to acid)	-
Cl 4.3, Table 1, S.no.xiii) (Resistance to alkali)	-
Cl 4.3, Table 1, S.no.xiv) (Resistance to Heat)	-

-
For colour, finish, wet opacity, resistance to acid, alkali and heat approved sample is required. Test facility is not available for mentioned exclusion parameter.; Excluding Water content;

950

IS 14735 (1999)

Unplasticized Polyvinyl Chloride (UPVC) Injection Moulded Fittings for Soil and Waste Discharge System for Inside and Outside Buildings Including Ventilation and Rain Water System -

Total Testing Charges : Rs. 9970.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5 (Colour of fittings)	-
7.1,Table 1 (Wall thickness)	-
7.2 ,Table 2&3 (Socket Dimensions)	-
10 (Workmanship)	-
11.1 (Solvent cement type or Rubber ring type)	-
11.2 (Socket and spigot configeration)	-
12.1 (Visual appearance)	-
12.2 (Stress relief test)	-
12.3 (Vicat softening tempewrature)	-
Cl.13, IS 12235 (P-7)-2004, (Resistance to Sulphuric Acid)	-
16.1 (Impact test)	-

-
Complete for mechanical requirements; Excluding Titanium dioxide content, effect on water;

951

IS 14151 : Part 1 (1999)

Irrigation equipment - Sprinkler pipes - Specification: Part 1 polyethylene pipes (First Revision)

Rs.17350/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.3 (Tensile Test)	-
7.2 (Reversion Test)	-
6.1 (VISUAL APPEARANCE)	-
5.1 table -1 (DIMENSIONS OF PIPES)	-
4.1.1 (density shall be between 940.4 kg/m’ and 958.4 kg/m3 (both inclusive) when determined at 27°C according to procedure prescribed in Annex A of IS 7328. The value of the density shall also not differ from the nominal value by more than 3 kg/m2 as per 5.2.1.1 of IS 7328.)	-
Cl. 4.2 , IS 2530-1963, Cl. 10 (Cabon Black Content)	-
4.3 (Anti-oxidant)	-

-
-

952

IS 281 (2009)

Mild steel sliding door bolts for use with padlocks - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (SIZES)	-
6 (DIMENSIONS AND TOLERANCES-A)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-A)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-B)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-C)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-D)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-E)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-F)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-G)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-H)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-J)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-T)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-DIMENSIONS AND TOLERANCES-No. of Screw on Staple or Clip to accommodate Wood Screw N0 (IS 451))	-
6-Table 1 (DIMENSIONS AND TOLERANCES-No. of Rivets on bolts plates)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-No. of Rivets on Socket)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-No. of Screw holes on bolt)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-No. of Screw holes on Socket)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-No. of Screw holes on Staple)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-no. of 8m Sqire Holes for carriage bolts for plate and sockets)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-no. of 8m Sqire Holes for carriage bolts for Staple)	-
7.1 (MANUFACTURE-General)	-
7.2 (MANUFACTURE-Sliding Door Bolts, Plate Type)	-
7.3 (MANUFACTURE-Sliding Bolts, Clip or Bolt Type)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm;

953

IS 278 (2009)

Galvanized steel barbed wire for fencing - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5 Table-1 (Sizes Diameter of Line wire)	-
5 Table-1 (Sizes Diamater of Point wire)	-
5 Table-1 (Sizes Mass of Completed barbed wire)	-
5 Table-1 (Sizes Distance between two barbs)	-
5 Table-1 (Sizes No. of Lays between the two consequtive barbs)	-
7.1 (Manufacture)	-
7.2 (Manufacture)	-
9.1 (Freedom from defects)	-
12.1 (Tensile Strength)	-
12.1 (Breaking load)	-
12.2.1 (Mass of zinc coating (line wire))	-
12.2.2 (Mass of zinc coating (point wire))	-
12.2 (Uniformity of zinc coating)	-
12.3 (Ductility)	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M) (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M) (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M) (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M) (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M) (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-

-
Grade of the material and type of killing as per IS 7887 may please be declared.;

954

IS 10124 : Part 2 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 2 specific requirements for sockets (Second Revision)

Rs.1800/ View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2.1, Table-1, Fig-1 (Minimum wall thickness for working pressure)	-
Clause 3.2.2, and Fig. 2. (Minimum wall thickness for working pressure)	-
3.2.2, and Fig. 2 (Dimensions of Socket for Elastomeric Sealing Ring Joint)	-

-
Excluding Test facility not available for Cl 6.2 Short Term Hydraulic Test, Cl 5.1.3 Out of Roundness;

955

IS 10124 : Part 1 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 1 General Requirements (Second Revision)

Rs 1500/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 Table-1 Fig.1 (Dimension of Socket length)	-
5.2 Table-2 Fig.2 (Dimensions of socket for elastomeric sealing ring)	-

-
Excluding Test facility not available for Cl 6.2 Short Term Hydraulic Test, Cl 5.1.3 Out of Roundness;

956

IS 276 (2000)

Austenitic - Manganese steel castings - Specification (First Revision)

please see remarks View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8.1,8.3, Table 1 (C)	-
8.1,8.3, Table 1 (Si)	-
8.1,8.3, Table 1 (Mn)	-
8.1,8.3, Table 1 (p)	-
8.1,8.3, Table 1 (S)	-
8.1,8.3, Table 1 (Cr)	-
8.1,8.3, Table 1 (Mo)	-
8.1,8.3, Table 1 (Ni)	-
9.1 (WORKMANSHIP AND FINISH)	-
10.1 (FREEDOM FROM DEFECTS)	-
14.2 (Brinell Hardness Test)	-
14.3 (Bend Test)	-
14.4, IS 1608 Pt 1 (Tensile test)	-

-
-

957

IS 210 (2009)

Grey iron castings - Specification (First Revision)

Rs.2700.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 (Chemical Composition(chemical composition shall be as agreed to between the purchaser and the manufacturer.))	-
7.1 (WORKMANSHIP AND FINISH)	-
10.1 (FREEDOM FROM DEFECTS)	-
10.2 (FREEDOM FROM DEFECTS)	-
13 (SIZE OF TEST BARS-Diameter)	-
13 (SIZE OF TEST BARS-Length)	-
15, Table 3 (TENSIL.E TEST- IS 1608 Part1 )	-
16, Table 3 (Hardness Test)	-
17,Annex B (TRANSVERSE TEST)	-

-
Since the composition of cast iron shall be left to the discretion ofthe manufacturer , as such element to be tested with specified requirement and tolerances if any may please be declared with method of testing. Sample Size 5 pcs of 5x5 cm having dia> 3mm and thickness > 0.8 mm.; Excluding -; Microstracture,Frequency of test,Tensile test(preparing of sample Above 28),Transverse test,Hydrostatic test

958

IS 208 (1996)

Door Handles - Specification ( Sixth Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2 -Table 1- i (Ref. Cl 7.1 -Table 3 Grade 0 of IS 1079 : 2017) (Chemical composition - Carbon - IS 228)	-
4.2 -Table 1- iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983) (Chemical composition - Copper plus incidental nickel - IS 3685:1966)	-
4.2 -Table 1- iv (Ref. Cl 5.1, Table 1 Grade 5230 or 4600 of IS 617 : 1994) (Chemical composition - Copper - IS 504:1963, IS 7658:1975, IS 11035:1984)	-
4.2 -Table 1- v (Ref. Cl 6, Table 1 Grade 19000 of IS 737 : 2008) (Chemical composition - Aluminium - IS 504:1963)	-
4.2 -Table 1- vi (Ref. Cl 5.1, Table 1 Grade 63400 or 65032 of IS 733 : 1983) (Chemical composition - Aluminium - IS 504:1963)	-
4.2 -Table 1- vii (Ref. Cl 6.1 of IS 210 : 2009) (Chemical composition - Sulphur and/or Phosphorous)	-
4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981) (Chemical composition - Aluminium- IS 2600:1964)	-
4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981) (Chemical composition - Impurities-Nickel- IS 2600:1964)	-
3 (TYPES-Doors handle shall be of the following types according to the materials used:)	-
5.1 (MANUFACTURE- General)	-
6.1 Table2A & 2B and Fig 1,2,3,4 (DIMENSIONS - Size (A,B,C,D,E,F,G,H,I))	-
6.1 Table2A & 2B and Fig 1,2,3,4 (DIMENSIONS - Size 1. No. in each Lug 2. No. in a plate when a continious plate is used 3. Size Designation of Counter-sunk Head Wood Screws (as per IS 6760: 1972))	-

-
Test facility is available for material test only as per Table 1. Sample dia > 3mm or thickness > 0.8 mm can only be tested, Sample size 5 pcs 5x5 cm; Excluding All except Coating Test;

959

IS 1166 (1986)

Specification for condensed milk, partly skimmed and skimmed condensed milk (Second Revision)

10430 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.5.1.10.1 (Salmonella IS 5887 Part 3)	-
Cl.5.1.10.1 (Shigella IS 5887 Part 7)	-
Cl.5.1.10.2 (Coliform Count IS 5401 Part 1)	-
Cl.5.1.10.3 (Yeast and Mould Count IS 5403)	-
Cl.5.1.10.4 (Coagulase positive Staphylococcus aureus IS 5887 Part 2)	-
Cl.5.1.10.5 (Escherichia coli IS 5887 Part 1)	-
Table 1 (i) (Apendix B) (Total milk solids -Condensed Milk)	-
Table 1 (ii) (IS : 11762- 1986) (Fat -Condensed Milk)	-
Table 1 (iii) (Apendix C) (Sucrose -Condensed Milk)	-
Table 1 (vi) (Apendix D) (Titratable acidity (as lactic acid) -Condensed Milk)	-

-
500 gm x 3

960

IS 205 (1992)

Non - Ferrous metal butt specification (Fourth Revision)

1500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1- Table 2,3,4,5 & Fig-1 & 2 (Dimensions- Type of Hinge 1.Length 2.Breadth 3.Butt Dia 4.Pin Dia 5.Thickness of Flap)	-
5.1- Table 2,3,4,5 & Fig-1 & 2 (Dimensions- 1. Holes for Screw Desination 2. No. of screw Holes)	-
6.1 (Manufacture- General)	-
6.2- Table 2,3,4,5 (Kunckles)	-
6.3 (Screw Holes)	-
6.3.1- Table 2,3,4,5 & Fig-1 & 2 (Screw Holes)	-
6.3.2- Table 2,3,4,5 (Number of Holes)	-
6.3.3 Fig-1 (Position of Holes)	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983) (Chemical composition - Aluminium - IS 504)	-
4 -Table 1- Flap-ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989) (Chemical composition - Copper - IS 3685:1966)	-
4 -Table 1- Flap-iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983) (Chemical composition - Copper plus incidental nickel - IS 3685:1966)	-
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977) (Chemical composition - Copper - IS 3635:1966)	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983) (Chemical composition - Aluminium - IS 504)	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987) (Chemical composition - Tin - IS 4027:1967)	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992) (Chemical composition - Carbon - IS 228)	-
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981) (Chemical composition - Copper - IS 3685:1966)	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995) (Chemical composition - Carbon - IS 228)	-

-
Grade/Designation of material of componenets as per Table 1 may please be declared. Sample dia > 3mm or thickness > 0.8 mm can only be tested;

Bureau of Indian Standards

The National Standards Body of India

BIS, Central Laboratory (CL)

20/9, Site 4, Sahibabad Industrial Area, Sahibabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201010

- sample@bis.gov.in

Scope List