BIS - LIMS (Laboratory Information Management System)

BIS, Central Laboratory (CL)

20/9, Site 4, Sahibabad Industrial Area, Sahibabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201010

- sample@bis.gov.in

Scope List

Reset

965 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

151

IS 15030 (2022)

TEREPHTHALIC ACID - SPECIFICATION (First revision)

4288 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2-Table 1-(i) (Moisture content)	-
3.2-Table 1-(ii) (Colour, Pt-Co)	-
3.2-Table 1-(iv) (Acid value)	-
3.2-Table 1-(viii) (4-carboxybenzaldehyde + p-toluic acid)	-

-
Excluding Clause 3.2, Table 1 (i) Moisture Content, (vii) 4-carboxybenzaldehyde (viii) 4-carboxybenzaldehyde + p-Toluic Acid;

152

IS 15392 (2003)

Aluminium and aluminium alloy bare foil for food packaging - Specification

3371 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 11 (Average Thickness)	-
Clause 12 (Dimension and Tolerances: I) Width)	-
Clause 12 (Dimension and Tolerances: 2) Length)	-
Clause 11 (Average Thickness)	-
Clause 12 (Dimension and Tolerances: I) Width)	-
Clause 12 (Dimension and Tolerances: 2) Length)	-

-
Test facility not avilable on Spark OES since thickness < 0.8 mm. Excluding Cl. 5 Pinhole count, Cl.13 Tensile Properties.

153

IS/IEC 61331 : Part 3 (2014)

PROTECTIVE DEVICES AGAINST DIAGNOSTIC MEDICAL X-RADIATION PART 3: PROTECTIVE CLOTHING, EYEWEAR AND PROTECTIVE PATIENT SHIELDS

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.4 (Dimensions)	-
6.4 (Dimensions)	-

-
-

154

IS 2095 : Part 2 (2022)

Gypsum plaster boards - specification: Part 2 Coated laminated gypsum plaster boards Third Revision of IS 2095 Part 2

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
(Clause 6.1.1) (Dimensions - Width,Length, Thickness (mm))	-

-
-

155

IS 14862 (2000)

Fibre cement flat sheets - specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1.1 (Nominal Length )	-
5.1.1 (Nominal Width)	-
5.1.4.1 (Straightness of edges - Length )	-
5.1.4.2 (Squareness of edges)	-

-
Excluding Thickness, Bending strength , Water impermeability , Freeze-thaw , Warm water , Soak-dry , Heat-rain test

156

IS 2925 (1984)

Specification for industrial safety helmets (Second Revision)

Rs 7770/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Sizes)	-
7.1 (Construction)	-
8.2 (Performance Requirements)	-
3.3 (Material)	-

-
10 pieces of helmet for complete testing.

157

IS 16651 (2017)

High Strength Deformed Stainless Steel Bars and Wires for Concrete Reinforcement - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1 (Specified Lengths)	-
7.2 (Nominal Mass)	-
8.2 (Tensile Properties)	-
8.3 (Bend and Rebend Properties)	-
8.4 (Bond Strength)	-
8.6 (Charpy Impact Test)	-
Table-1, Clause - 4.3.1 (CARBON)	-
Table-1, Clause - 4.3.1 (SULPHUR)	-
Table-1, Clause - 4.3.1 (PHOSPHURS)	-
Table-1, Clause - 4.3.1 (MANGANESE)	-
Table-1, Clause - 4.3.1 (NITROGEN)	-
Table-1, Clause - 4.3.1 (SILICON)	-
Table-1, Clause - 4.3.1 (COPPER)	-
Table-1, Clause - 4.3.1 (CHROMIUM)	-
Table-1, Clause - 4.3.1 (NICKEL)	-
Table-1, Clause - 4.3.1 (MOLYBDENUM)	-

-
Steel designation may be declared . 5 pcs of 5x5 cm sample having dia > 3mm and/or thickness > 0.8 mm shall be provided. Excluding Cl.8.2 Tensile Properties (Elongation at breaking, 0.2% Proof stress),Cl.5.7 Pull out test,Cl.8.5 Fatigue test,Cl.8.7 Inter-Granular corrosion test.

158

IS 1069 (2021)

QUALITY TOLERANCES FOR WATER FOR STORAGE BATTERIES - SPECIFICATION

900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2 , Table - 1 , i) (pH)	-
3 (Descripiton)	-

-
Excluding Cl 4.Table 1.ii) Specific Electrical Conductivity

159

IS 2785 (2022)

CHEESE - SPECIFICATION (Second Revision of IS 2785)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.2.1 (Appearance - IS 2785 :2022)	-
5.2.3 (Texture and Consistency)	-
3 and 5.3 Table 1 (i) (e) Harvati 30 percent (Milk fat (On dry basis) IS 12758-2005)	-
5.4 Table 2-i (Coliform-IS 5401(P-1):2012)	-
5.4 Table 2-ii (S.aureus-IS 5887(P-8/Sec-1):2002)	-
5.4 Table 2-iii (Yeast & Mould count-IS 5403:1999)	-
5.4 Table 2-iv (E.coli-IS 5887(P-1):1976)	-
5.4 Table 2-v (Salmonella spp.-IS 5887(P-3/Sec-1):2020)	-
5.4 Table 2-vi (L.monocytogenes-IS 14988(P-1):2020)	-
5.5 Table 3-i (Aerobic Colony count - IS 5402 (Part 2))	-
5.5 Table 3-ii (Coliform-IS 5401(P-1):2012)	-
5.5 Table 3-iii (S.aureus-IS 5887(P-8/Sec-1):2002)	-
5.5 Table 3-iv (E.coli-IS 5887(P-1):1976)	-
5.5 Table 3-v (Salmonella spp.-IS 5887(P-3/Sec-1):2020)	-
5.5 Table 3-vi (L.monocytogenes-IS 14988(P-1):2020)	-
3 and 5.3 Table 1 (i) © Semi Soft chesse (Moisture IS- 2785-2022)	-

-
500 gm x 3 Excluding 1-Lactose

160

IS 2347 (2023)

DOMESTIC PRESSURE COOKER ï¿½ SPECIFICATION

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Gross capacity)	-
4.2 (Body Capacity)	-
5.1 (Body, Lid, Containers and Grid)	-
5.1.2 (Body and Lid )	-
5.1.3 (Stainless steel pressure cooker)	-
5.1.4 (Aluminium cooker )	-
5.2 (Safety Relief Device)	-
5.3 (Gasket)	-
5.4 (Handles and Knobs)	-
5.5 (Pressure Regulating Device )	-
5.6 (Vent Seal Pin for Pressure Regulating Device )	-
5.7 (Vent Pipe )	-
5.8 (Vent Pipe Nut )	-
5.9 (Spring )	-
5.1 (Material of Rim )	-
5.11 (Visual Pressure Indicator)	-
5.12 (Gasket Release System)	-
6 (Construction)	-
7 (Workmanship and Finish )	-
8.1 (Air Pressure Test )	-
8.2 (Proof Pressure Test )	-
8.3 (Operating Test for Pressure Regulating Device )	-
8.4 (Test for Safety Relief Device )	-
8.5 (Bursting Pressure Test )	-
8.6 (Test for Removal of Lid under Pressure )	-
8.7 (Test for Spring Loaded Mechanism )	-
8.8 (Composite Cooker Base )	-
8.9 (Aluminium induction compatible Base )	-
8.1 (Handles of cooker )	-
8.11 (External Coating)	-
8.12 (Internal Coating )	-
8.13 (Integral electrical heating)	-
8.14 (Ply construction cooker Body )	-
8.15.1 (Fragmentation Test )	-
8.15.2 (Ball Drop Test )	-
8.15.3 (Thermal Shock Test )	-
8.15.4 (Free Fall Test)	-
8.17 (Test for Effectiveness for Induction Bottom)	-
11 (Marking )	-
12 (Packing )	-
4 (Capacity)	-
4.2 (Body Capacity)	-
5.1.1 (Body, Lid, Containers and Grid)	-
5.1.2 (Body, Lid, Containers and Grid)	-
5.1.3 (Body, Lid, Containers and Grid)	-
5.1.4 (Body, Lid, Containers and Grid)	-
5.1.5 (Body, Lid, Containers and Grid)	-
5.2.1 (Destructive Type Safety Relief Device)	-
5.2.2 (Resettable Type Safety Relief Device)	-
5.3 (Gasket)	-
5.4 (Handles and Knobs)	-
5.5 (Pressure Regulating Device)	-
5.6 (Vent Seal Pin for Pressure Regulating Device)	-
5.7 (Vent Pipe)	-
5.8 (Vent Pipe Nut)	-
5.9 (Spring)	-
5.10 (Spring)	-
5.11 (Visual Pressure Indicator)	-
5.12 (Gasket Release System)	-
6 (CONSTRUCTION)	-
6.1 (Pressure Regulating Device)	-
6.1.1 (Pressure Regulating Device)	-
6.1.1 (Minimum Inside diameter of Vent Pipe.)	-
6.1.2 (Pressure Regulating Device)	-
6.1.3 (Pressure Regulating Device)	-
6.1.4 (Pressure Regulating Device)	-
6.1.5 (Pressure Regulating Device)	-
6.1.6 (Pressure Regulating Device)	-
6.2 (Safety Relief Device)	-
6.2.1 (Safety Relief Device)	-
6.2.2 (Safety Relief Device)	-
6.2.3 (Safety Relief Device)	-
6.3.1 (Temperature Responsive Safety Relief Device)	-
6.3.2 (Temperature Responsive Safety Relief Device)	-
6.3.3 (Temperature Responsive Safety Relief Device)	-
6.4.1 (Handles and Knobs)	-
6.4.1.1 (Handles and Knobs)	-
6.4.2 (Handles and Knobs)	-
6.4.2.1 (Handles and Knobs)	-
6.5 (CONSTRUCTION)	-
6.6 (CONSTRUCTION)	-
6.7 (Internal Level Marking)	-
6.8 (Internal Level Marking)	-
7.1 (WORKMANSHIP AND FINISH)	-
7.2 (WORKMANSHIP AND FINISH)	-
8.17 (Test for Effectiveness for Induction Bottom)	-
8.16 (PRD with chain)	-
8.15.4.2 (Glass lid without rim)	-
8.15.4.1 ("Free Fall Test ( Glass lid with rim) ")	-
8.15.3 (Thermal Shock Test on Tempered Glass lid)	-
8.15.2 (Ball Drop Test on Tempered Glass lid)	-
8.15.1 (Fragmentation Test on Tempered Glass lid)	-
8.14 (3 ply construction cooker body)	-
8.13 (Pressure cooker with integral electrical heating)	-
8.12 (Internal Coating)	-
7.3 (WORKMANSHIP AND FINISH)	-
7.4 (WORKMANSHIP AND FINISH)	-
8.1 (Air Pressure Test)	-
8.2 (Proof Pressure Test)	-
8.3.1 (Operating Test for Pressure Regulating Device)	-
8.4.1 (Test for Safety Relief Device)	-
8.4.2 (Test for Safety Relief Device)	-
8.4.2 NOTE (Test for Safety Relief Device)	-
8.5 (Bursting Pressure Test)	-
8.6.1 (Tests for Removal of Lid under Pressure For Outer Lid Cooker)	-
8.6.2 (Tests for Removal of Lid under Pressure For inner Lid Cooker)	-
8.6.3 (Tests for Removal of Lid under Pressure: For Cooker Fastened by Screw Clamps or Any Other Locking Device)	-
8.6.4 (Tests for Removal of Lid under Pressure in case of electrical pressure cooker)	-
8.7 (Test for Spring Loaded Mechanism)	-
8.8 (Test for stainless steel cookers)	-
8.9 ("For stainless steel, aluminium induction compatible base and 3 ply cooker")	-
8.10 (Testing of Handles of the cooker)	-
8.10 Note 3 (Testing of Handles of the cooker)	-
8.10 Note 4 (Testing of Handles of the cooker)	-
8.10 Note 5 (Testing of Handles of the cooker)	-
8.10 Note 6 (Testing of Handles of the cooker)	-
8.10.1 (Testing of Handles of the cooker)	-
8.11.1 (External Coating)	-

-
-

161

IS 17945 (2022)

FOOD FOR SPECIAL MEDICAL PURPOSE INTENDED FOR INFANTS ï¿½ SPECIFICATION

Please See Remerk View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (Description - IS 17945)	-
5.4 (Scorched Particles - IS 13500)	-
Clause 5.6 (as per details of table 1, clause 5.7 of IS 14433:2022) (Carotenes (Optional Parameter) - IS 17671 or ILL/STP/INST/050)	-
"5.12 Table 2 (i) " (Aerobic plate count-IS 5402 (Part 1))	-
"5.12 Table 2 (ii)" (Staphylococcuus aureus-IS 5887 (Part 8/Sec-1))	-
"5.12 Table 2 (iv)" (Salmonella sp.-IS 5887 (Part 3))	-
"5.12 Table 2 (ix)" (Enterobacter Sakazakii(Cronobacter spp.)-ISO 22964)	-
"5.12 Table 2 (iii)" (Yeast & mould count-IS 5403)	-
"5.12 Table 2 (v)" (Listeria monocytogenes-IS 14988 (Part 1))	-
v (Bacillus cereus-IS 5887 (Part 6))	-
"5.12 Table 2 (vii)" (Sulphite reducing clostridia-ISO 15213)	-
"5.12 Table 2 (viii)" (Enterobacteriacae-is 17112(p-1))	-
5.11,Table 1(ii) (Total Protein - IS 7219)	-
5.11,Table 1(iii) ((a)Total Fat - IS 11721)	-

-
500 gm x 3 Excluding 1-Linoleic acid 2- α-Linolenic acid 3-Docosahexaenoic acid (DHA) 4-Eicosapentaenoic acid (EPA) 5-Arachidonic acid (ARA) 6-Sodium 7-Potassium 8-Calcium 9-Phosphate 10-Chloride 11-Magnesium 12-Iron 13-Zinc 14-Copper 15-Selenium 16-Manganese 17-Iodine 18-Chromium 19-Molybdenum 20-Thiamine 21-Riboflavin 22-Niacin 23-Pantothenic acid 24-Pyridoxine 25-Cobalamine 26-Folic acid, 27-L-Ascorbic acid (vitamin C) 28-Biotin 29-Vitamin A, μg retinol 30-Vitamin D "31-Vitamin E, mg, α-tocopherol equivalents" 32-Vitamin K 33-Choline 34-Inositol

162

IS 2052 (2023)

Compounded feeds for cattle ï¿½ Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl no.4.1 (General)	-
Cl no.4.3,7.1, Table no. 1(i) (Moisture)	-
Cl no.4.3,7.1, Table no. 1(ii) (Crude protein (N × 6.25))	-
Cl no.4.3, 7.1,Table no. 1(iii) (Crude fat)	-
Cl no.4.3 ,7.1, Table no. 1(iv) (Crude fibre)	-
Cl no.4.3 ,7.1, Table no. 1(v) (Acid insoluble ash)	-
Cl no.4.3,7.1Table no. 1(vi) ("Salt (as NaCl based on Na or Cl), percent by mass")	-
Cl no.4.3 7.1,Table no. 1(vii) (Calcium (as Ca))	-
4.3 Table no.1 (xiv) ("Aflatoxin B1 (ODB)/IS/ISO 14718* or ISO 17375 or AOAC 2003.02")	-
Cl no.4.3 ,7.1, Table no. 1(x) (Urea, percent by mass)	-
Cl no.4.3,7.1,Table no. 1(viii) (Total phosphorus)	-

-
500 gm x 3

163

IS 12171 (2019)

Cotton bales – Specification (third revision)

All the grades

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1.1 (Staple Length)	-

-
-

164

IS 9471 : Part 1 (1980)

Specification for modular lower limb orthotic components: Part 1 stirrups

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 2 (Type)	-
Cl. 2.1 (Type)	-
Cl. 3.1 (Shape and Dimensions)	-
Cl. 3.2 (Shape and Dimensions)	-
Cl. 3.3 (Shape and Dimensions)	-
Cl 4 (Material)	-
Cl. 5 (Workmanship and Finish)	-

-
-

165

IS 16988 (2018)

Compressed natural gas cylinder valve integrated with solenoid operation (Remotely Controlled) for automotive use - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.4.1 (Tensile Strength and Elongation)	-
5.4.2 (Impact Strength)	-
6.2 (Valve Dimensions)	-
7.2 (Relief/Bursting Pressure)	-
Clause-8.1 & 9 (Copper)	-
Clause-8.1 & 9 (Lead)	-
Clause-8.1 & 9 (Tin)	-
Clause-8.1 & 9 (Iron)	-
Clause-8.1 & 9 (Aluminium)	-
Clause-8.1 & 9 (Manganese)	-
Clause-8.1 & 9 (Nickel)	-
Clause-8.1 & 9 (Silicon)	-
Clause-8.1 & 9 (Chromium)	-
Clause-8.1 & 9 (Cobalt)	-
Clause-8.1 & 9 (Zinc)	-
Clause-8.1 & 9 (Other Impurities)	-

-
Steel designation may be declared . 5 pcs of 5x5 cm sample having dia > 3mm and/or thickness > 0.8 mm shall be provided.

166

IS/ISO 22702 (2003)

Uitility lighters - General consumer - Safety requirements

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Structural-integrity requirements- general)	-
8.0 (marking )	-

-
-

167

IS 3521 : Part 2 (2021)

Personal Fall Arrest Systems Specification Part 2 Lanyards and Energy Absorbers

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2.6 (Static strength)	-
4.3.5 (Dynamic performance)	-
5.2.4 (Corrosion resistance)	-
6.2 (Marking)	-
4.2.4 (Fittings)	-

-
Excluding Test Facility only for clauses 4.1, 4.2, 4.3

168

IS 648 (2022)

Cold rolled non-oriented electrical steel sheet and strip - Fully processed type - Specification Sixth Revision

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. No. 8.1 (Thickness for CRNO Strips)	-
Cl. No. 8.2 (Width Tolerance for CRNO strips)	-
Cl. No. 8.3 (Length Tolerance for CRNO strips)	-
Cl. No. 8.6 (Flatness (Wavefactor) for CRNO strips)	-
Cl. No. 9.2 & Table-1 (Ductility (Bend test) for CRNO Strips)	-

-
Grade/Designation or Element to be tested may be declared with specified requirement. Exclusion : All Except Dimension

169

IS 5509 (2021)

Fire Retardant Plywood - Specification ( Third Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
12.1 Table - 2 (i) (Moisture content, percent, Max)	-
8.1 (Dimensions)	-

-
Exclusion : No testing facility for requirements (ii), (iii), (iv) as per table 2 of clause 12.1 Sample Test Parameter not available: Cl 11.4 Static Bending Strength Above 15 mm thickness, Cl 12 Flammability, Flame penetration, Rate of burning Existing Sample Size:1 Full Size Sheet For All Tests Sample Size without dimensional measurements:Length-1500 mm, width-1200

170

IS 3521 : Part 1 (2021)

Personal Fall Arrest Systems Specification Part 1 Full Body Harness Fourth Revision

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (General)	-
4.2 (Classification)	-
4.3 (Design and Construction)	-
4.6 (Static Strength)	-
4.8 (Static Suspension Test)	-
4.3.2.3 (No of stitches per cm)	-
4.3.2.4 (Flammability)	-

-
-

171

IS 15381 (2021)

Fire Blanket - Specification ( First Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7 (Workmanship and Finish)	-
4.4 (Mass)	-
4.3 (Shape & Dimension)	-

-
Excluding Fire performance, Electrical resistance (Sample not received till date)

172

IS 12234 (2021)

Plastic equilibrium float valves for cold water services - Specification (first revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5 (Materials)	-
6 (Manufacture and Workmanship)	-
7.1 to 7.3 , 7.6 to 7.9 (Construction)	-
7.4 to 7.5 and 7.10 (Dimensions, Screw threads and Back nut)	-

-
-

173

IS 15450 (2022)

Polyethylene-aluminium-polyethylene composite pressure pipes for hot and cold water supplies Specifications first revision of IS 15450

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7 (NOMINAL DIAMETERS)	-
9 (DIMENSIONS OF PIPE)	-
10 (VISUAL APPEARANCE)	-
11.2 (Melt Flow Rate (Method of test as per Table 3))	-
11.1 (Density (Method of test as per Table 3))	-
11.8 (Adhesion Test)	-
11.9 (Apparent Tensile Strength of Pipe)	-
11.10 (Minimum Burst Pressure)	-
11.11 (Hydraulic Characteristics)	-
12.1 (Type Test)	-

-
-

174

IS 15500 : Part 1 to 8 (2021)

Deepwell Handpumps Components and Special Tools Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Fig. 6.13 of IS 15500 : PART 6 (2021) (Check Valve Seat-VLOM 65)	-
Fig. 6.12 of IS 15500 : PART 6 (2021) ("Check Valve Seat-Standard (for SDWP & EDWP)")	-
Fig. 6.11 of IS 15500 : PART 6 (2021) ("Rubber Seat Retainer (for SDWP, EDWP & FLP)")	-

-
-

175

IS 4572 (2022)

Fibre ropes - Polyamide 3- 4- 8- and 12- strand ropes (fifth revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6, Table 1, 2 and 3 (Linear Density)	-
6, Table 1, 2 and 3 (Minimum Breaking Strength)	-
5.1 - Type A (3- strand hawser-laid rope)	-
5.1 - Type B (4-strand shroud-laid rope)	-
5.1 - Type L (8-strand braided rope)	-
5.1 - Type T (12-strand braided rope)	-
6 (Physical properties)	-

-
-

176

IS 12406 (2021)

Medium density fibre boards for general purpose - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clauses 5.2, 9 and 10.2.2 (Density)	-
Clauses 5.2, 9 and 10.2.2 (Density)	-
Clauses 5.2, 9 and 10.2.2 (Variation from mean density)	-
Clauses 5.2, 9 and 10.2.2 (Moisture Content)	-
Clauses 5.2, 9 and 10.2.2 (Variation from mean moisture content)	-
Clauses 5.2, 9 and 10.2.2 (Linear expansion (Thickness Swelling in Water) Due to general Absorption after 24h soaking)	-
Clauses 5.2, 9 and 10.2.2 (Internal Bond Strength)	-
Clauses 5.2, 9 and 10.2.2 (Modulus of Rupture a) Avg. Value b) Min. Individual)	-
Clauses 5.2, 9 and 10.2.2 (Modulus of Elasticity a) Avg. Value b) Min. Individual)	-
Clauses 5.2, 9 and 10.2.2 (Screw withdrawl strength (i) Face (ii) Edge (For thickness >12mm))	-
8 (DIMENSIONS AND TOLERANCES)	-
Clauses 5.2, 9 and 10.2.2 (Formaldehyde Content (i) For Formaldehyde Class, E1 (ii) For Formaldehyde Class, E2)	-

-
Exclusion : Test Facility not avaialble for requirements such as CL 9 -Internal bond strength, Sample Test Parameter not available in CL: "Cl.s 5.2, 9 and Cl.10.2.2 Table Cl.3,4 Linear expansion, Internal bond strength (After cyclic test,After accelerated water resistance test), Modulus of rupture, Modulus of elasticity" Existing Sample Size: One Board For All Tests Sample Size without dimensional measurements: Length-1200 mm, width-1200

177

IS 17545 (2021)

WHITE CEMENT BASED POLYMERIC PUTTY

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.5 , Table 1 , 1) , iii) (Setting time Initial, Min Final, Max)	-
4.6 , Table 2 , 1) , i) (Compressive strength, 28 days, Min)	-

-
Not pertains to cement chemical

178

IS 648 (2006)

Cold rolled non-oriented electrical steel sheet and strip - Fully processed type - Specification (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8.1 (Thickness)	-
Cl 8.2 (Width)	-
Cl 8.3 (Length)	-
Cl 8.5 (Shape)	-
Cl 8.6 (Flatness)	-
Cl 8.6 (Flatness)	-
Cl 8.5 (Shape)	-
Cl 8.3 (Length)	-
Cl 8.2 (Width)	-
Cl 6.3 (Surface Condition)	-
Cl. No. 7.1.2.1 , 7.1.2.2 & Table-1 (Loss in W/kg)	-

-
IS has been superseded by 2022 version. Exclusion : All Except Dimension

179

IS 13095 (2020)

Butterfly Valves for General Purposes ( First Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.0 (VALVE END CONNECTIONS)	-
6.0 ( NOMINAL SIZES )	-
7.0 (NOMINAL PRESSURES)	-
7.2 (Class designations)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Flange-D)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges-IS 6418 (Table 2/3/6/7/10)- Flange-b)	-

-
-

180

IS 12795 (2020)

Linear Alkyl Benzene — Specification ( First Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2 & 7.1 - Table -1, Sl no. 2 (Specific gravity at 15.5°/15.5°C,IS 1448 [Part 32] or ASTM D-4052)	-
4.2 & 7.1 - Table -1, Sl no. 1 (b) In 5 inch cell on Lovibond scale, expressed as Y + 5R, Max, Annex A)	-
4.2 & 7.1 - Table -1, Sl no. 3 (Moisture, ppm, Max,5 of IS 286 or ISO 12937 or ASTM D-6304 or UOP 481)	-

-
Excluding Determination of molecular weight and concentration of linear alkyl benzene, Determination of paraffins, determination of sulphonability, determination of chain length distribution, determination of refrective index, determination o\f teralins, LAB content, ready biodegradibility of sulphonate, bromine index, doctor test , Colour

First
Prev
5
6
7
8
Next
Last

Bureau of Indian Standards

The National Standards Body of India

BIS, Central Laboratory (CL)

20/9, Site 4, Sahibabad Industrial Area, Sahibabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201010

- sample@bis.gov.in

Scope List