BIS - LIMS (Laboratory Information Management System)

BIS, Central Laboratory (CL)

20/9, Site 4, Sahibabad Industrial Area, Sahibabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201010

- sample@bis.gov.in

Scope List

Reset

979 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

181

IS 3521 : Part 2 (2021)

Personal Fall Arrest Systems Specification Part 2 Lanyards and Energy Absorbers

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2.6 (Static strength)	-
4.3.5 (Dynamic performance)	-
5.2.4 (Corrosion resistance)	-
6.2 (Marking)	-
4.2.4 (Fittings)	-

-
Excluding Test Facility only for clauses 4.1, 4.2, 4.3

182

IS 648 (2022)

Cold rolled non-oriented electrical steel sheet and strip - Fully processed type - Specification Sixth Revision

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. No. 8.1 (Thickness for CRNO Strips)	-
Cl. No. 8.2 (Width Tolerance for CRNO strips)	-
Cl. No. 8.3 (Length Tolerance for CRNO strips)	-
Cl. No. 8.6 (Flatness (Wavefactor) for CRNO strips)	-
Cl. No. 9.2 & Table-1 (Ductility (Bend test) for CRNO Strips)	-

-
Grade/Designation or Element to be tested may be declared with specified requirement. Exclusion : All Except Dimension

183

IS 5509 (2021)

Fire Retardant Plywood - Specification ( Third Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
12.1 Table - 2 (i) (Moisture content, percent, Max)	-
8.1 (Dimensions)	-

-
Exclusion : No testing facility for requirements (ii), (iii), (iv) as per table 2 of clause 12.1 Sample Test Parameter not available: Cl 11.4 Static Bending Strength Above 15 mm thickness, Cl 12 Flammability, Flame penetration, Rate of burning Existing Sample Size:1 Full Size Sheet For All Tests Sample Size without dimensional measurements:Length-1500 mm, width-1200

184

IS 3521 : Part 1 (2021)

Personal Fall Arrest Systems Specification Part 1 Full Body Harness Fourth Revision

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (General)	-
4.2 (Classification)	-
4.3 (Design and Construction)	-
4.6 (Static Strength)	-
4.8 (Static Suspension Test)	-
4.3.2.3 (No of stitches per cm)	-
4.3.2.4 (Flammability)	-

-
-

185

IS 15381 (2021)

Fire Blanket - Specification ( First Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7 (Workmanship and Finish)	-
4.4 (Mass)	-
4.3 (Shape & Dimension)	-

-
Excluding Fire performance, Electrical resistance (Sample not received till date)

186

IS 12234 (2021)

Plastic equilibrium float valves for cold water services - Specification (first revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5 (Materials)	-
6 (Manufacture and Workmanship)	-
7.1 to 7.3 , 7.6 to 7.9 (Construction)	-
7.4 to 7.5 and 7.10 (Dimensions, Screw threads and Back nut)	-

-
-

187

IS 15450 (2022)

Polyethylene-aluminium-polyethylene composite pressure pipes for hot and cold water supplies Specifications first revision of IS 15450

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7 (NOMINAL DIAMETERS)	-
9 (DIMENSIONS OF PIPE)	-
10 (VISUAL APPEARANCE)	-
11.2 (Melt Flow Rate (Method of test as per Table 3))	-
11.1 (Density (Method of test as per Table 3))	-
11.8 (Adhesion Test)	-
11.9 (Apparent Tensile Strength of Pipe)	-
11.10 (Minimum Burst Pressure)	-
11.11 (Hydraulic Characteristics)	-
12.1 (Type Test)	-

-
-

188

IS 15500 : Part 1 to 8 (2021)

Deepwell Handpumps Components and Special Tools Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Fig. 6.13 of IS 15500 : PART 6 (2021) (Check Valve Seat-VLOM 65)	-
Fig. 6.12 of IS 15500 : PART 6 (2021) ("Check Valve Seat-Standard (for SDWP & EDWP)")	-
Fig. 6.11 of IS 15500 : PART 6 (2021) ("Rubber Seat Retainer (for SDWP, EDWP & FLP)")	-

-
-

189

IS 4572 (2022)

Fibre ropes - Polyamide 3- 4- 8- and 12- strand ropes (fifth revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6, Table 1, 2 and 3 (Linear Density)	-
6, Table 1, 2 and 3 (Minimum Breaking Strength)	-
5.1 - Type A (3- strand hawser-laid rope)	-
5.1 - Type B (4-strand shroud-laid rope)	-
5.1 - Type L (8-strand braided rope)	-
5.1 - Type T (12-strand braided rope)	-
6 (Physical properties)	-

-
-

190

IS 12406 (2021)

Medium density fibre boards for general purpose - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clauses 5.2, 9 and 10.2.2 (Density)	-
Clauses 5.2, 9 and 10.2.2 (Density)	-
Clauses 5.2, 9 and 10.2.2 (Variation from mean density)	-
Clauses 5.2, 9 and 10.2.2 (Moisture Content)	-
Clauses 5.2, 9 and 10.2.2 (Variation from mean moisture content)	-
Clauses 5.2, 9 and 10.2.2 (Linear expansion (Thickness Swelling in Water) Due to general Absorption after 24h soaking)	-
Clauses 5.2, 9 and 10.2.2 (Internal Bond Strength)	-
Clauses 5.2, 9 and 10.2.2 (Modulus of Rupture a) Avg. Value b) Min. Individual)	-
Clauses 5.2, 9 and 10.2.2 (Modulus of Elasticity a) Avg. Value b) Min. Individual)	-
Clauses 5.2, 9 and 10.2.2 (Screw withdrawl strength (i) Face (ii) Edge (For thickness >12mm))	-
8 (DIMENSIONS AND TOLERANCES)	-
Clauses 5.2, 9 and 10.2.2 (Formaldehyde Content (i) For Formaldehyde Class, E1 (ii) For Formaldehyde Class, E2)	-

-
Exclusion : Test Facility not avaialble for requirements such as CL 9 -Internal bond strength, Sample Test Parameter not available in CL: "Cl.s 5.2, 9 and Cl.10.2.2 Table Cl.3,4 Linear expansion, Internal bond strength (After cyclic test,After accelerated water resistance test), Modulus of rupture, Modulus of elasticity" Existing Sample Size: One Board For All Tests Sample Size without dimensional measurements: Length-1200 mm, width-1200

191

IS 17545 (2021)

WHITE CEMENT BASED POLYMERIC PUTTY

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.5 , Table 1 , 1) , iii) (Setting time Initial, Min Final, Max)	-
4.6 , Table 2 , 1) , i) (Compressive strength, 28 days, Min)	-

-
Not pertains to cement chemical

192

IS 648 (2006)

Cold rolled non-oriented electrical steel sheet and strip - Fully processed type - Specification (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8.1 (Thickness)	-
Cl 8.2 (Width)	-
Cl 8.3 (Length)	-
Cl 8.5 (Shape)	-
Cl 8.6 (Flatness)	-
Cl 8.6 (Flatness)	-
Cl 8.5 (Shape)	-
Cl 8.3 (Length)	-
Cl 8.2 (Width)	-
Cl 6.3 (Surface Condition)	-
Cl. No. 7.1.2.1 , 7.1.2.2 & Table-1 (Loss in W/kg)	-

-
IS has been superseded by 2022 version. Exclusion : All Except Dimension

193

IS 13095 (2020)

Butterfly Valves for General Purposes ( First Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.0 (VALVE END CONNECTIONS)	-
6.0 ( NOMINAL SIZES )	-
7.0 (NOMINAL PRESSURES)	-
7.2 (Class designations)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Flange-D)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges-IS 6418 (Table 2/3/6/7/10)- Flange-b)	-

-
-

194

IS 12795 (2020)

Linear Alkyl Benzene — Specification ( First Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2 & 7.1 - Table -1, Sl no. 2 (Specific gravity at 15.5°/15.5°C,IS 1448 [Part 32] or ASTM D-4052)	-
4.2 & 7.1 - Table -1, Sl no. 1 (b) In 5 inch cell on Lovibond scale, expressed as Y + 5R, Max, Annex A)	-
4.2 & 7.1 - Table -1, Sl no. 3 (Moisture, ppm, Max,5 of IS 286 or ISO 12937 or ASTM D-6304 or UOP 481)	-

-
Excluding Determination of molecular weight and concentration of linear alkyl benzene, Determination of paraffins, determination of sulphonability, determination of chain length distribution, determination of refrective index, determination o\f teralins, LAB content, ready biodegradibility of sulphonate, bromine index, doctor test , Colour

195

IS 12299 (2021)

DAIRY WHITENER - SPECIFICATION First Revision

All

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Table 2 /clause no 6.4 SI.No.i) (Aerobic Plate count)	-
CL 6.4, Table 2 (ii) (Coliform Count)	-
CL 6.4, Table 2 (iii) (Staphylococcus aureus (Coagulase positive))	-
CL 6.4, Table 2 (iv) (Yeast and Mold Count)	-
CL 6.4, Table 2 (v) (Salmonella sp)	-
CL 6.4, Table 2 (vi) (Listeria monocytogenes)	-
CL 6.4, Table 2 (vii) (Bacillus cereus)	-
CL 6.4, Table 2 (viii) (Sulphite reducing clostridia)	-
CL 6.4, Table 2 (ix) (E. coli)	-
Table 6.4/clause no(i) ( Moisture)	-
Table 6.4/clause no(iii) (Milk protein)	-
Table 6.4/clause no(ii) ( Milk fat)	-
Table 6.4/clause no(iv) (Insolubility index)	-
Table 6.4/clause no(vi) (Acid insoluble ash)	-
Table 6.4/clause no(viii) (Titrable acidity)	-
6.4, Table 1, (ix) (Scorched Particle)	-

-
500 gm x 3

196

IS 1989 : Part 2 (1986)

Specification for leather safety boots and shoes: Part 2 for heavy metal industries (Fourth Revision)

Rs 5100/- for safety boots, Rs.4500/- safety shoes View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7 (Design)	-
8 (a) Upper Leather)	-
10 (Finish)	-
17 (a) Shoes with Leather Sole and Heel)	-
15 (Manufacture)	-
14 (k) Screw Wire)	-
14 (j) Rivets)	-
14 (h) Toe Compound)	-
9 (Manufacture)	-

-
Exclusion Chromium Mechanical complete :Except i) Threads Cl 8.9 Cl 14.9 Material requirement 4 pair for complete testing along with raw material with spacified requirment as per ISs

197

IS 1989 : Part 1 (1986)

Specification for leather safety boots and shoes: Part 1 for miners (Fourth Revision)

Rs 5100/- for safety boots, Rs.4500/- safety shoes View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1 (Design)	-
10.1 (Finish)	-
10.3 (Finish)	-
10.4 (Finish)	-
11.1 (Mass Boots with Leather Sole and Heel)	-
11.2 (Mass Boots with Rubber Sole and Heel)	-
13 (Design)	-
16.2 (Finish)	-
16.3 (Finish)	-
16.4 (Finish)	-
17.1 (Mass Shoes with Leather Sole and Heel)	-
17.2 (Mass Shoes with Rubber Sole and Heel)	-

-
Exclusion Chromium Mechanical (complete) except i) Threads Cl 8.9 Cl 14.9 Materail requirement :4 pair for complete testing along with raw material with spacified requirment as per Iss

198

IS 11544 (1986)

Specification for slipper, rubber

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (Shape & Design)	-
3.2.2 (Bottom Filling Material)	-
3.2.8 (Workmanship and Finish -)	-
3.2.5 (Type of Thread)	-
3.2.6 (Thickness of components)	-
3.2.4.1 (Weave of fabrics)	-

-
Complete for chemical (relative Density)

199

IS 5676 (1995)

Moulded solid rubber soles and heels - SpecificatlOn (Second Revision)

Rs.5100/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5/5.1 (REQUIREMENTS-General)	-
5/5.2- Fig. 1 to 5 (REQUIREMENTS-Design)	-
5/5.3/5.3.1 (REQUIREMENTS- Construction)	-
5/5.7- Table2 (REQUIREMENTS- Physical Requirements- as per IS 3400 (Part 1, Part 2, Part 4, Part 9, Part 10, Part 16))	-

-
Complete for chemical (relative Density) Mechanical (Complete) except ; i)Tear strength (Table 1). Raw material requirement : 3 pair of complete footwear along with raw material with specified requirement as per ISs and For abrasion resistance to outsole raw material of 10 mm min. thickness required

200

IS 6664 (1992)

Rubber microcellular sheets for soles and heels - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.4 Cl.4.1.3 And 8.3,Table1, i) (Relative density)	-
Cl.4.1.3 And 8.3,Table1, iii) (Hardness, Shore A durometer min)	-
Cl.4 Cl.4.1.3 And 8.3,Table1, iii) (Change in Hardness after ageing at 100±1°C for 24hr)	-
Cl.4 Cl.4.1.3 And 8.3,Table1, iv) (Compression set at constant stress percent, Max)	-
Cl.4 Cl.4.1.3 And 8.3,Table1, v) (Split tear strength, kg,Min)	-
Cl.4 Cl.4.1.3 And 8.3,Table1, viii) (Water absorption , percent by mass, Max)	-
Cl.4 Cl.4.1.3 And 8.3,Table 1, viii) (Flexing resistance: Maximum cut growth at 50 000 cycles)	-
Cl.4 Cl.4.1.3 And 8.3,Table 1, vi) (Heat shrinkage test at 100±1°C for 1 hour max)	-

-
Complete for chemical Mechanical (complete ) excluding Compression set at constant stress Table 1 Raw material with specified requirement as per ISs and For abrasion resistance to outsole raw material of 10 mm min. thickness required

201

IS 6719 (1972)

Solid Pvc Soles And Heels

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 3.1,3.2,3.3,3.4,3.5 (Material)	-
3.6 (i) (Relative density )	-
3.6 (ii) (Tensile Strength )	-
3.6 (iii) (Elongation at break, percent )	-
3.6 (iv) (Tear Strength a) Force Part b) Back Part )	-
3.6 (v) (Volatility, percent by means )	-

-
Complete for chemical Mechanical (Completed) except ; i)Tear strength (Table 1) Raw material requirement :3 pair of complete footwear along with raw material with specified requirement as per ISs and For abrasion resistance to outsole raw material of 10 mm min. thickness required

202

IS 13995 (1995)

Unlined moulded rubber boots - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Thickness )	-
5.1.1 (Tensile Strength (before ageing))	-
5.1.2 (Tensile Strength (after ageing))	-
5.1.3 (Tear Strength)	-
5.1.5 (Flexing resistance of upper)	-
5.1.6 (Design)	-
5.1.7 (Size)	-

-
No Chemical testing Mechanical (Complete) Except :i) Tear Resistance of Upper (Cl 5.1.3) Material requirement :4 pair for complete testing along with raw material with spacified requirment as per ISs

203

IS 16645 (2018)

Moulded Plastics Footwear ” Lined or Unlined Polyurethane Boots for General Industrial use ” Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Soling Pattern )	-
5.1 (General )	-
5.2 (Resistance to flexing of boot upper)	-
5.4 (Hardness (IRHD))	-
5.5 (Cold flex temp of upper)	-
5.6 (Resistance to soling to cut growth)	-
5.7 (Split tear strength )	-

-
No Chemical testing Mechanical ( Complete) Except i) Cold flex temperature of the upper (Cl 5.5) Material requirement: 4 pair for complete testing along with raw material with spacified requirment as per ISs

204

IS 17012 (2018)

High ankle tactical boots with pu - Rubber sole - Specification

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2 (Design )	-
4.3.1 (Size)	-
4.4 (Height of upper )	-
4.5.1 (Construction)	-
4.5.2 (Ergonomic Feature)	-
4.5.4 (Slip Resitance)	-
4.5.5 (Antistatic test)	-
4.5.6 (Heat Insulation of sole Complex)	-
4.5.7 (Cold Insulation of sole complex)	-
4.6.1 (Thickness )	-
4.6.2 (Tear Strength)	-
4.7.1 (Material vamp & Quarter)	-
4.7.4 (Abrasion resistance )	-
4.7.5 (Water Vapour permeability & coefficient )	-
4.9.3 (Water absorption & desorption percent)	-
4.14.6 (Hardness (IRHD))	-
4.16.2 (Breaking Strength of lace )	-
5.0 (Innocuousness Test IS 17011)	-

-
Complete for Chemical ( The material composition of each shoe part must be clearly declared for testing) Mechanical (Complete) except Energy absorption of seat region (CL 4.5.8) Raw material Requirement :4 pair of complete footwear and their raw materials with the required specifications as per ISs and For abrassion resistance to outsole raw material of 10 mm min. thickness required

205

IS 17037 (2018)

Anti riot shoes - Specification

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.5.6.1 (General)	-
4.3.1 (Size)	-
4.4 (Height of upper )	-
4.5.4 (Slip Resitance)	-
4.5.5.1 (Dimension)	-
4.3.2 (Weight)	-
4.5.4 (Slip Resitance)	-
4.5.5.2 (Flex resistance )	-
4.5.5.1 (Dimension)	-
4.5.6.1 (General)	-
4.5.6.2 (Internal Toe cap length)	-
4.5.6.3 (Impact resistance )	-
4.5.6.4 (Compression resistance)	-
4.5.7.1 (Antistatic test)	-
4.5.8 (Heat insulation of sole complex)	-
4.6.2 (Tear Strength)	-
4.6.3 (Water vapour permeability & coefficent )	-
4.7.4 (Abrasion resistance )	-
4.14.4 (Hardness (IRHD))	-
Cl-5 (IS - 17011,Table - 1(i) (Allergenic and carcinogenic disperse dyes)	-
Cl-5 (IS - 17011,Table - 1(ii) (Aromatic amines released from Azo dyes (each individual amine))	-
Cl-5 (IS - 17011,Table - 1(iii) (Aromatic amines released from Azo dyes (each individual amine))	-
Cl-5 (IS - 17011,Table - 1(iv) (Chromium (VI))	-
Cl-5 (IS - 17011,Table - 1(v) (Dimethyl fumarate (DMFU))	-
Cl-5 (IS - 17011,Table - 1(vi) (Formaldehyde (free or released by partial hydrolysis))	-
Cl-5 (IS - 17011,Table - 1(viii) (Organotin compounds)	-
Cl-5 (IS - 17011,Table - 1(ix) (PCP-TeCP-TriCP polychlorophenols)	-
Cl-5 (IS - 17011,Table - 1(x) (pH)	-
Cl-5 (IS - 17011,Table - 1(xi) (Phthalates (each individual phthalate))	-
Cl-5 (IS - 17011,Table - 1(xii) (Nickel, on skin contact)	-

-
Complete for Chemical ( The material composition of each shoe part must be clearly declared for testing) Mechanical (Complete) except; Energy absorption of seat region As per Cl 4.5.10 Raw Material Requirement: 4 pair of complete footwear and their raw materials with the required specifications as per ISs and For abrasion resistance to outsole raw material of 10 mm min. thickness required

206

IS 12254 (2021)

POLYVINYLCHLORIDE PVC INDUSTRIAL BOOTS - SPECIFICATION Second Revision

20400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.2 (Size)	-
5.3 (Height)	-
5.4.2 (Ergonomic feature)	-
5.4.4 (Slip resistance)	-
5.4.5 (Leak proofness)	-
5.4.6.1 (Toe caps General)	-
5.4.6.2 (Internal length of toecaps)	-
5.4.6.4 (Impact resistance)	-
5.4.6.3 (Corrosion resistance)	-
5.4.6.5 (Compression resistance)	-
5.4.7 (Colour)	-
5.5.1 (Upper Thickness)	-
5.5.2 (Upper tensile strength)	-
5.5.3 (Upper flexing)	-
5.5.4 (Upper Hardness)	-
5.6.1 (Lining material)	-
5.6.2 (Lining Tear strength)	-
5.6.3 (Lining abrasion)	-
5.7.1 (Insole thickness)	-
5.7.2 (Insole abrasion)	-
5.7.3 (Water absorption and desorption)	-
5.9.2 (Inscok abrasion resistance)	-
5.9.3 (Insock water absorption and desorption)	-
5.11.1 (Outsole thickness)	-
5.11.2 (Outsole density)	-
5.11.3 (Outsole Interlayer bond)	-
5.11.4 (Outsole tear)	-
5.11.5 (Outsole Abrasion)	-
5.11.6 (Outsole hardness)	-
5.11.7 (Outsole flexing)	-
6.1 (Volatility)	-
6.2 (Lead content)	-
Table 1 as per IS 17011 2018 (pH)	-
Table 1 as per IS 17011 2018 (Phthalates (each individual phthalate))	-
Table 1 as per IS 17011 2018 (Nickel, on skin contact)	-
Table 1 as per IS 17011 2018 (Allergenic and carcinogenic disperse dyes)	-
Table 1 as per IS 17011 2018 (Aromatic amines released from Azo dyes (each individual amine))	-
Table 1 as per IS 17011 2018 (Chromium (VI))	-
Table 1 as per IS 17011 2018 (Dimethyl fumarate (DMFU))	-
Table 1 as per IS 17011 2018 (Formaldehyde (free or released by partial hydrolysis))	-
Table 1 as per IS 17011 2018 (Organotin compounds)	-
Table 1 as per IS 17011 2018 (PCP-TeCP-TriCP polychlorophenols)	-

-
Complete for Chemical ( The material composition of each shoe part must be clearly declared for testing) Mechanical (Complete) except ; Closing Thread (Cl 5.10) material requirement: 4 pair for complete testing along with raw material with specified requirement as per ISs and For abrasion resistance to outsole raw material of 10 mm min. thickness required

207

IS 3735 (1996)

Canvas Shoes, Rubber Sole

Rs. 20470/- excluding colour fastness. View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1.1 Upper, Sl No. (i) of Table 1 (The upper shall consist of over layer of cotton, manmade or blended conforming' to the requirements given in Sl No. (i) of Table 1 as an overlayer and cotton drill conforming to the requirements given in Sl No. (ii) of Table 1, as an inner layer or lining. The two fabrics shall be firmly adhered together with rubber compound. )	-
Cl.4.1.5 Laces ( The shoes shall be provided with fabric braided laces either matching the shade of the upper or black or The length of the lace shall be 60 ± 3 cm )	-
4.1.6 (Tensile strength)	-
Cl.4.1.6.2 Ageing (None of the rubber components of the shoes shall show any sign of tackiness or crack developed after ageing, when examined visually)	-
4.1.3 (Construction )	-

-
No chemical testing Mechanical (complete) Except : i)Threads for upper closing (Cl 4.1.3) ii) Consolidation test (Cl 4.5) iii) Compression set ISO 3400 Part 10 Raw material requirements :4 pair for complete testing along with raw material with specified requirement as per ISs

208

IS 3736 (1995)

Canvas boots, rubber sole - Specification (Second Revision)

Rs 7650/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1.2 Lining Material (195 ± 5 picks/dm shall be used.)	-
Cl.4.1.7.4 Ageing (The boots shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the soles and heels of the boots shall conform to the physical requirements prescribed in Table 5. i) Tensile Length)	-
Cl.4.1.1 upper IS 1969 (d) Picks/dm)	-
4.1.2 Lining Material (For covering of the insole, cotton drill conforming to Table 1, Sl No. (ii) shall be used. For detachable insole, bleached cotton twill of breaking load 390 N Min in warp way and)	-
Cl.4.1.4 Reinforcement Material (The back seam, joining two quarters at the back of the heel shall be reinforced with a not less than 25 mm wide tape made out of material conforming to Sl No. (i) of Table 1)	-
Cl.4.1.5 Thread for Upper Closing Cl.4.1.5.1 (IS 1670:1991) (Sewing thread cotton, man made or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirements. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirement of specification.')	-
Cl.4.1.7.3 IS 3400 (Part 10) : 1977 (Compression set, in percent. Max)	-
Cl.4.1.7.5 Thickness of components (Individual components of the boots shall comply with the thickness and material requirements prescribed in Table 6.)	-
Cl.4.3 Leg Height (The leg height of the boots for size 8 shall be 160 ± 2 mm with an increase or decrease of 4 mm of the nominal height for each bigger or smaller sizes respectively when measured at the inside from the back of the boot from insole to the top.)	-
Cl.4.5.1(Cl.4.1.6.) ( Each pair of boot shall be provided with a pair of braided fabric laces of the quality as prescribed in 4.1.6.)	-
Cl.4.6 Mass (The mass of finished boots, rubber sole, of size 8 shall not exceed 1130 g per pair, and the mass shall increase or decrease by 75 g per pair for each bigger or smaller size respectively.)	-

-
No chemical testing Mechanical (Complete) Except i) 4.1.1.1 Colour fastness ii) Thread Counts of Material ( Table 1)Threads ( Cl 4.1.5) iii) Tensile Test of Sewing Threads (Clause 4.1.5.1) iii) Compression set (Table 4) iv) Consolidation Test (Clause 4.7) Raw material requirements : 4 pair for complete testing along with raw material with specified requirement as per ISs.

209

IS 3976 (2018)

Safety Rubber Canvas Boots for Miners Ã¢â‚¬ Specification ( Sixth Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (Design)	-
5.2.4 (Reinforcing Material)	-
5.3, 5.3.1,5.3.3,5.3.4 (Construction)	-
Cl.5.5 Mass (The mass of one pair of finished footwear of size 8 shall not exceed 1 500 g for Type 1 and 1 400 g for Type 2 with an increase or decrease of 100 g for each bigger or smaller size, respectively.)	-
Cl.5.6 ( Height of Upper Height of upper of the boots shall conform to column 5 (Design C) and column 4 (Design B) of 5.2.2, Table 4 of IS 15298 (Part 2) for Type 1 and Type 2, respectively when measured as per 6.2 of IS 15298 (Part 1) on the inside of the back of the footwear and from seat of the insole to top edge of the upper.)	-
Cl.5.7 Performance Test (When safety footwear is tested in accordance with the method described in 5.4 of IS 15298 (Part 1), at an impact energy of (200 ± 4) J, the clearance under the toecap at the moment of impact shall be in accordance with Table 5. In addition, the toecap shall not develop any cracks which go through the material, that is, through which light can be seen.)	-
Cl.5.11 Compression Resistance ( 5.11.1 When safety boots are tested in accordance with 5.5 of IS 15298 (Part 1), the clearance under the toe cap at a compression load of 15 kN ± 0.1 kN shall be in accordance with Table 5.)	-
Cl.5.12 Internal Length of Toe Cap ( For safety boots, internal length of the toe cap shall meet the specification given in Table 5 of IS 15298 (Part 2) when tested as per 5.3 of IS 15298 (Part 1).)	-
Cl.5.2.7 Safety Toe Cap (Safety toe cap as per 3.6 shall be fitted into the footwear and must not come out while in use.)	-
Cl.5.2.5.4 Thickness of compact sole hee (Thickness of compact sole heel of the boots shall comply with the thickness and material requirements prescribed in Table 3.)	-
Cl.5.2.5 Compact Sole Heel 5.2.5.1 IS 3400 (Part 4) (ii)*Change in hardness after accelerated ageing at 100 ± 2 °C for 24 h )	-

-
No chemical testing Mechanical (Complete) ; Except i) 5.2.1.1 Composite upper material ( consolidation test as per 5.10) ii) Energy Absorption Test (5.13) Raw Material Requirement :4 pair for complete testing along with raw material with specified requirement as per ISs and For abrasion resistance to outsole raw material of 10 mm min. thickness required

210

IS 11226 (1993)

Leather safety footwear having direct moulded rubber sole specification (First Revision)

Rs. 26520/- excluding adhesion test on mould. View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (REQUIREMENTS)	-
5.2 (Materials)	-
5.2.11 (Relative density )	-
5.2.11 (Hardness (IRHD))	-
5.2.11 (Tensile Strength)	-
5.2.11 (Elongation at break)	-
5.2.11 (Flexing resistance)	-
5.2.4 (Materials)	-

-
Mechanical Complete Material requirement :4 pair of sole Raw and material with spacified requirment as per ISs

First
Prev
6
7
8
9
Next
Last

Bureau of Indian Standards

The National Standards Body of India

BIS, Central Laboratory (CL)

20/9, Site 4, Sahibabad Industrial Area, Sahibabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201010

- sample@bis.gov.in

Scope List