BIS - LIMS (Laboratory Information Management System)

BIS, Central Laboratory (CL)

20/9, Site 4, Sahibabad Industrial Area, Sahibabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201010

- sample@bis.gov.in

Scope List

Reset

899 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

121

IS 3736 (1995)

Canvas boots, rubber sole - Specification (Second Revision)

Rs 7650/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1.2 Lining Material (195 ± 5 picks/dm shall be used.)	-
Cl.4.1.7.4 Ageing (The boots shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the soles and heels of the boots shall conform to the physical requirements prescribed in Table 5. i) Tensile Length)	-
Cl.4.1.1 upper IS 1969 (d) Picks/dm)	-
4.1.2 Lining Material (For covering of the insole, cotton drill conforming to Table 1, Sl No. (ii) shall be used. For detachable insole, bleached cotton twill of breaking load 390 N Min in warp way and)	-
Cl.4.1.4 Reinforcement Material (The back seam, joining two quarters at the back of the heel shall be reinforced with a not less than 25 mm wide tape made out of material conforming to Sl No. (i) of Table 1)	-
Cl.4.1.5 Thread for Upper Closing Cl.4.1.5.1 (IS 1670:1991) (Sewing thread cotton, man made or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirements. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirement of specification.')	-
Cl.4.1.7.3 IS 3400 (Part 10) : 1977 (Compression set, in percent. Max)	-
Cl.4.1.7.5 Thickness of components (Individual components of the boots shall comply with the thickness and material requirements prescribed in Table 6.)	-
Cl.4.3 Leg Height (The leg height of the boots for size 8 shall be 160 ± 2 mm with an increase or decrease of 4 mm of the nominal height for each bigger or smaller sizes respectively when measured at the inside from the back of the boot from insole to the top.)	-
Cl.4.5.1(Cl.4.1.6.) ( Each pair of boot shall be provided with a pair of braided fabric laces of the quality as prescribed in 4.1.6.)	-
Cl.4.6 Mass (The mass of finished boots, rubber sole, of size 8 shall not exceed 1130 g per pair, and the mass shall increase or decrease by 75 g per pair for each bigger or smaller size respectively.)	-

-
No chemical testing Mechanical (Complete) Except i) 4.1.1.1 Colour fastness ii) Thread Counts of Material ( Table 1)Threads ( Cl 4.1.5) iii) Tensile Test of Sewing Threads (Clause 4.1.5.1) iii) Compression set (Table 4) iv) Consolidation Test (Clause 4.7) Raw material requirements : 4 pair for complete testing along with raw material with specified requirement as per ISs.

122

IS 3976 (2018)

Safety Rubber Canvas Boots for Miners Ã¢â‚¬ Specification ( Sixth Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (Design)	-
5.2.4 (Reinforcing Material)	-
5.3, 5.3.1,5.3.3,5.3.4 (Construction)	-
Cl.5.5 Mass (The mass of one pair of finished footwear of size 8 shall not exceed 1 500 g for Type 1 and 1 400 g for Type 2 with an increase or decrease of 100 g for each bigger or smaller size, respectively.)	-
Cl.5.6 ( Height of Upper Height of upper of the boots shall conform to column 5 (Design C) and column 4 (Design B) of 5.2.2, Table 4 of IS 15298 (Part 2) for Type 1 and Type 2, respectively when measured as per 6.2 of IS 15298 (Part 1) on the inside of the back of the footwear and from seat of the insole to top edge of the upper.)	-
Cl.5.7 Performance Test (When safety footwear is tested in accordance with the method described in 5.4 of IS 15298 (Part 1), at an impact energy of (200 ± 4) J, the clearance under the toecap at the moment of impact shall be in accordance with Table 5. In addition, the toecap shall not develop any cracks which go through the material, that is, through which light can be seen.)	-
Cl.5.11 Compression Resistance ( 5.11.1 When safety boots are tested in accordance with 5.5 of IS 15298 (Part 1), the clearance under the toe cap at a compression load of 15 kN ± 0.1 kN shall be in accordance with Table 5.)	-
Cl.5.12 Internal Length of Toe Cap ( For safety boots, internal length of the toe cap shall meet the specification given in Table 5 of IS 15298 (Part 2) when tested as per 5.3 of IS 15298 (Part 1).)	-
Cl.5.2.7 Safety Toe Cap (Safety toe cap as per 3.6 shall be fitted into the footwear and must not come out while in use.)	-
Cl.5.2.5.4 Thickness of compact sole hee (Thickness of compact sole heel of the boots shall comply with the thickness and material requirements prescribed in Table 3.)	-
Cl.5.2.5 Compact Sole Heel 5.2.5.1 IS 3400 (Part 4) (ii)*Change in hardness after accelerated ageing at 100 ± 2 °C for 24 h )	-

-
No chemical testing Mechanical (Complete) ; Except i) 5.2.1.1 Composite upper material ( consolidation test as per 5.10) ii) Energy Absorption Test (5.13) Raw Material Requirement :4 pair for complete testing along with raw material with specified requirement as per ISs and For abrasion resistance to outsole raw material of 10 mm min. thickness required

123

IS 11226 (1993)

Leather safety footwear having direct moulded rubber sole specification (First Revision)

Rs. 26520/- excluding adhesion test on mould. View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (REQUIREMENTS)	-
5.2 (Materials)	-
5.2.11 (Relative density )	-
5.2.11 (Hardness (IRHD))	-
5.2.11 (Tensile Strength)	-
5.2.11 (Elongation at break)	-
5.2.11 (Flexing resistance)	-
5.2.4 (Materials)	-

-
Mechanical Complete Material requirement :4 pair of sole Raw and material with spacified requirment as per ISs

124

IS 17043 (2018)

Derby shoes - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.15.1 (Length of laces )	-
4.3.2 (Weight)	-
4.4, Table 3 (Height of the Upper)	-
4.2 (Design )	-
4.5.3 (Bond Strength)	-
4.5.3.1 (Upper/outsole bond strength)	-
4.5.3.2 (Interayer bond strength)	-
4.5.4 (Slip Resitance)	-
4.5.5.1 (Electrical Properties Antistatic )	-
4.5.6 (Heat insulation of sole complex)	-
4.5.7 (Cold insulation tester )	-
4.6.1 (Upper Material)	-
4.6.2 (Tear Strength)	-
4.6.3 (Water vapour permeability & coefficent )	-
4.6.4 (Water penetration and water absorption)	-

-
No chemical testing Mechanical (Complete) Except : i) Pull out test of eyelet (Cl 4.14) ,ii)Tag retention (Cl 4.15.2) iii) Colour peel test (Cl 4.14),iv) Cl 4.5.8 Energy absorption of seat region Raw material Requirement: 4 pair for complete testing along with raw material with specified requirement as per ISs

125

IS 10702 (2023)

Hawai Chappal-Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Material)	-
4.2 (Length)	-
4.3 (Thickness)	-
4.4 , Table No. 1 , i) (Density)	-
4.4 , Table No. 1 , iii) (3Split tear strength)	-
Cl. No.5.1,Table no.1 of IS 17011(x) (pH)	-
Cl. No.5.1,Table no.1 of IS 17011(xi) (Phthalates (each individual phthalate))	-
Cl. No.5.1,Table no.1 of IS 17011(vii) (Formaldehyde)	-

-
No chemical testing Mechanical (Complete) Sample requirement: 6 pair of Complete footwear along with their raw materials of the required specification as mentioned in ISS. For outsole abrasion test, Raw material of outsole of min.10mm thickness is required.

126

IS 6721 (2023)

SANDAL AND SLIPPERS SPECIFICATION First revision

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. No.4 (SHAPE AND DESIGN)	-
Cl. No.5 ("SIZE AND FITTINGS ")	-
Cl. No.6 ("CONSTRUCTION ")	-
Cl. No.7 (MATERIAL)	-
Cl. No.8.1, Table no. 1(i),a ("Tear strength, (other than moulded upper material) ")	-
Cl. No.8.1, Table no. 1(i),b ("For all moulded upper material ")	-
Cl. No.8.2,Table no. 2(ii),a ("Abrasion resistance- At dry condition")	-
Cl. No.8.3,Table no. 3(ii),b ("Abrasion resistance- At wet condition")	-
Cl. No.8.4,Table no. 4(ii) (Density)	-
Cl. No.8.6.1,Table 1 of IS 17011(xi) (Phthalates (each individual phthalate))	-

-
No chemical testing Mechanical (Complete) Except: i) Attachment strength of elastic, limit of useful extension table ii) Tear strength (Table 2,3&4) Mechanical (Complete ) Type 2 Sample Size Requirement: 4 pairs of complete footwear and raw material of lining, insole covering & upper with required specifications as per ISs and For abrasion resistance to outsole raw material of 10 mm min. thickness required

127

IS 15844 : Part 2 (2023)

SPORTS FOOTWEAR PART -2 PERFORMANCE SPORTS FOOTWEAR

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1.6 (Complete Shoe Flexing)	-
7.2 , Table No. 2 , iv) ,a) (Water vapour permeability)	-
7.2 , Table No. 2 , iv) ,b) (Water vapour coefficient)	-
7.2 , Table No. 2 , vii) (Tensile strength)	-
7.2 , Table No. 2 , viii) (Elongation at break,)	-
7.2 , Table No. 2 , x) (Abrasion test (for unlined upper))	-
7.12, Table no. 1 of IS 17011,(x) (pH)	-
7.12, Table no. 1 of IS 17011,(xi) (Phthalates (each individual phthalate))	-
7.12, Table no. 1 of IS 17011,(vii) (Formaldehyde)	-

-
Excluding Chemical requirement as per IS 17011 (Innocuousness ); Mechanical (Partial) Except : i) Energy absorption at seat region cl 7.1.5, ii) Washability cl 7.1.7, iii) Colour fastness rubbing table 2, iv) Colour fastness to light table 2, v) Strength at needle perforation table 3, , vi) Bursting strength table 3, vii) Colour fastness to rubbing table 4, viii) Colour fastness to perspiration table 4, ix) Elastic Tape cl 7.10, x) Fasteners cl 7.11, material requirement :4 pair of complete footwear and raw material with required specifications as per ISs and For abrassion resistance to outsole raw material of 10 mm min

128

IS 15844 : Part 1 (2023)

SPORTS FOOTWEAR PART -1 GENERAL PURPOSEFirst Revision

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl No.4.4 , Table No. 2 , i) , a) (Flexing resistance, Dry condition)	-
Cl No.4.4 , Table No. 2 , i) , b) (Flexing resistance, Wet condition)	-
Cl No.4.4 , Table No. 2 , iv) , a) (Water vapour permeability, mg/cm2h, Min)	-
Cl No.4.4 , Table No. 2 , iv) , b) (Water vapour coefficient, mg/cm2 , Min)	-
Cl No.4.10 , Table No. 8 , iii) (Moisture resistance, percent, Min)	-
Cl No . 4.14, Table no. 1 of IS 17011(x) (pH)	-
Cl No . 4.14, Table no. 1 of IS 17011(xi) (Phthalates (each individual phthalate))	-
Cl No . 4.14, Table no. 1 of IS 17011(vii) (Formaldehyde)	-

-
No chemical testing Mechanical TF (Partial for Type 1); Following test are not available: i)Energy absorption at seat region Cl. 4.3.6 ii) Washability Cl. 4.3.8 (Optional) iii) Colour fastness to light (Optional) as per Table 1 iv) Bursting Strength, kg/cm2 , Min (Additional test required for Knitted Fabrics) as per Table 2 v) Colour fastness to perspiration(contact method) table 3 vi) Elastic Tape(limit of useful extension ) as per Table 10 / Lace tag strength as per Table 11 / Colour fastness to water of Table 11. Complete Mechanical Test Facility for Type 2. Sample Size requirement: 4 pairs of complete footwear and raw material with required specifications as per ISs and For abrasion resistance to the outsole, raw material of 10 mm min. thickness required.

129

IS 15844 (2010)

Sports Footwear Specification

Single phase energy meters-Rs. 16179/- • Three phase en View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.7 (Tensile Strength)	-
3.8 (Elongation at Break )	-

-
No chemical testing Excluding i) Energy absorption at seat region cl 3.3.4, ii) Lastometer test table 3, iii) Colour fastness & Fastness to artificial light, iv) Compression Set, v) Ross flaxing, vi) Flaxing index table 10, vii) Abrasion resistance of lace material table 14, viii) Counter material table 15

130

IS 16532 (2017)

APP Modified Bituminous Waterproofing and Damp-Proofing Membrane with Polyester Reinforcement - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1.1, Table 1 (i) (polyester reinforced membrane, Mass)	-
5.1, 5.2, Table 2 (Dimensions and weight of AAP membrane polyester)	-
6, Table 4 (iiv) (Heat resistance)	-
6, Table 4 (ix) (Water absorption)	-

-
-

131

IS 12300 (1988)

Valve fittings for refrigerant cylinders - Specification

Rs 8700/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
As per Clause 8.1 & 9, Table 3 (Copper)	-
As per Clause 8.1 & 9, Table 3 (Lead)	-
As per Clause 8.1 & 9, Table 3 (Tin)	-
As per Clause 8.1 & 9, Table 3 (Iron)	-
As per Clause 8.1 & 9, Table 3 (Aluminium)	-
As per Clause 8.1 & 9, Table 3 (Manganese)	-
As per Clause 8.1 & 9, Table 3 (Nickel)	-
As per Clause 8.1 & 9, Table 3 (Silicon)	-
As per Clause 8.1 & 9, Table 3 (Chromium)	-
As per Clause 8.1 & 9, Table 3 (Cobalt)	-
As per Clause 8.1 & 9, Table 3 (Zinc)	-
As per Clause 8.1 & 9, Table 3 (Lead)	-
As per Clause 8.1 & 9, Table 3 (Iron)	-
As per Clause 8.1 & 9, Table 3 (Silicon)	-
(Cl 2) (Material)	-
(Cl 2) (Material)	-

-
Grade/Designation or Element to be tested may be declared with specified requirement

132

IS 2556 : Part 6 (2021)

Vitreous China sanitary appliances - Specification: Part 6 Specific requirements of urinal and partition plates (fifth revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 4 (GENERAL REQUIREMENTS)	-
Cl 5 (PATTERNS AND SIZES)	-
Cl 6.1 (DIMENSIONS AND TOLERANCES)	-
Cl 7 (CONSTRUCTION)	-
Cl 8 ()	-
Cl 6.1 (DIMENSIONS AND TOLERANCES)	-
Cl 6.2 (DIMENSIONS AND TOLERANCES)	-
Cl 6.3 (DIMENSIONS AND TOLERANCES)	-
Cl 7 (CONSTRUCTION)	-
Cl 4 (GENERAL REQUIREMENTS)	-

-
-

133

IS 2556 : Part 6 (1995)

Vitreous sanitary appliances (Vitreous China): Part 6 specific requirements of urinals and partition plates

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5 (Dimensions & Tolerances)	-
Cl 4 (Patterns and Size)	-
Cl 6 (Construction)	-
Cl 5 (Dimensions & Tolerances)	-
Cl 7 (Finish)	-

-
-

134

IS 3748 (2022)

Tool Steels - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.2 (Carbon)	-
7.2 (Silicon)	-
7.2 (Manganese)	-
7.2 (Chromium)	-
7.2 (Sulphur)	-
7.2 (Phosphorus)	-
7.2 (Cobalt)	-
7.2 (Molybdenum)	-
7.2 (Vanadium)	-
7.2 (Tungsten)	-
7.2 (Nickel)	-
7.2 (Nitrogen)	-
7.4 (Shape, dimensions and tolerances)	-
7.3 (Surface Quality)	-
7.2 (Hardness Test)	-

-
Steel/name designation may be declared . 5 pcs of 5x5 cm sample having dia > 3mm and/or thickness > 0.8 mm shall be provided. Excluding Cl 7.3 Surface Quality

135

IS 13893 (1994)

Polyurethane soles semirigid - specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2 (Thickness )	-
4.3 (Elongation at break)	-
4.3 (Tensile Strength )	-
4.2 (Thickness )	-
4.1 (Design)	-
4.3 (Relative density )	-

-
Mechanical (Complete) Except :i) Tensile strength (Cl 4.3.1) ii) Elongation at break (Cl 4.3.1) iii) Tear strength (Cl 4.3.1) Material requirement :3 pair of complete footwear along with raw material with specified requirement as per ISs and For abrasion resistance to outsole raw material of 10 mm min. thickness required

136

IS 14756 (2022)

Draft Indian Standard STAINLESS STEEL COOKWARE SPECIFICATION Second Revision of IS 14756

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
As per Clause 3 (Carbon)	-
As per Clause 3 (Silicon)	-
As per Clause 3 (Manganese)	-
As per Clause 3 (Nickel)	-
As per Clause 3 (Chromium)	-
As per Clause 3 (Sulphur)	-
As per Clause 3 (phosphorus)	-
As per Clause 3 (Nitrogen)	-
As per Clause 3 (Titanium)	-
As per Clause 3 (Aluminium)	-
As per Clause 3 (Copper)	-
As per Clause 3 (Magnesium)	-
As per Clause 3 (Iron)	-
As per Clause 3 (Zinc)	-
As per Clause 3 (Arsenic)	-
As per Clause 3 (Antimony)	-
As per Clause 3 (Bismith)	-
As per Clause 3 (Lead)	-
As per Clause 3 (Tellurium)	-
4.1 (Annex A) (Shapes and Dimensions)	-
4.2 (Table 1) (Shapes and Dimensions)	-
4.2 (Table 1) (Shapes and Dimensions)	-
4.2 (Shapes and Dimensions)	-
4.3 (Shapes and Dimensions)	-
4.4 (Shapes and Dimensions)	-
5.1 (Workmanship and Finish)	-
5.1 (Workmanship and Finish)	-
5.1 (Workmanship and Finish)	-
5.2 (Workmanship and Finish)	-
6.5 (Coating Thickness Test (For Copper Deposit))	-
6.7.1 (Nominal Capacity Test)	-
6.7.2 (Nominal Capacity Test- Diameter)	-
6.8.3 (Tests on Tempered Glass Lid (thermal shock test))	-
6.8.4.1 (Tests on Tempered Glass Lid (Free Fall Test with rim facing down))	-
6.8.4.2 (Tests on Tempered Glass Lid (Free Fall Test without rim facing down))	-
4.2 (Shapes and Dimensions)	-

-
Grade designation as per Cl. 3 may be declared . 5 pcs of 5x5 cm sample having dia > 3mm and/or thickness > 0.8 mm shall be provided

137

IS 1285 (2002)

Wrought aluminium and aluminium alloys - Extruded round tube and hollow sections for general engineering purposes - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
As per Clause 8 Table ! (Aluminium)	-
As per Clause 8 Table ! (Copper)	-
As per Clause 8 Table ! (Magnesium)	-
As per Clause 8 Table ! (Silicon)	-
As per Clause 8 Table ! (Iron)	-
As per Clause 8 Table ! (Manganese)	-
As per Clause 8 Table ! (Zinc)	-
As per Clause 8 Table ! (Titanium)	-
As per Clause 8 Table ! (Chromium)	-
6 (Cl. 6 CONDITIONS OF SUPPLY)	-
5/5.2 (FREEDOM FROM DEFECTS)	-
7/a) Extruded round tube IS 2673 (DIMENSIONS AND TOLERANCE-Extruded round tube - outside Dia or Inside Dia)	-
7 of IS 1285 /a) Extruded round tube IS 2673 (DIMENSIONS AND TOLERANCE-Extruded round tube - Wall thickness)	-
7 of IS 1285 /a) Extruded round tube IS 2673 (DIMENSIONS AND TOLERANCE-Extruded round tube - Allowable Deviation of Mean Diameter from Specified Diameter (Size Tolerance))	-
7 of IS 1285 /a) Extruded round tube IS 2673 (DIMENSIONS AND TOLERANCE-Extruded round tube - Allowabte Deviation of Diameter at Any Point from Specified Diameter (Ovality Tolcrance))	-
7 of IS 1285 /a) Extruded round tube IS 2673 (DIMENSIONS AND TOLERANCE-Extruded round tube -Straightness)	-
7 of IS 1285 /a) Extruded round tube IS 2673 (DIMENSIONS AND TOLERANCE-Extruded round tube -Length)	-
7 of IS 1285 / b) Extruded hollow sections IS 6477 (DIMENSIONS AND TOLERANCE-Extruded hollow sections -SPECIFIED WIDTH or WIDTH ACROSS FLATS)	-
7 of IS 1285 / b) Extruded hollow sections IS 6477 (DIMENSIONS AND TOLERANCE-Extruded hollow sections -Flatness)	-
7 of IS 1285 / b) Extruded hollow sections IS 6477 (DIMENSIONS AND TOLERANCE-Extruded hollow sections -Twist)	-
9 (Mechanical Comp[osition -IS 1285)	-
12 (Marking)	-
7 of IS 1285 /a) Extruded round tube IS 2673 (DIMENSIONS AND TOLERANCE-Extruded round tube -Length)	-

-
-

138

IS 15757 (2022)

FOLLOW-UP FORMULA-COMPLEMENTARY FOODS - SPECIFICATION (First Revision of IS 15757)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 4.8,Table 2 ,Sl No i) (Aerobic plate count)	-
Clause 4.8,Table 2 ,Sl No ii) (Coliform Count)	-
Clause 4.8,Table 2 ,Sl No iii) (Staphylococcus aureus( Coagulase positive))	-
Clause 4.8,Table 2 ,Sl No iv) (Yeast and mould count)	-
Clause 4.8,Table 2 ,Sl No v) (Salmonella sp.)	-
"4.8 Table 2 (vi) " (Listeria monocytogenes- IS 14988 (Part 1))	-
Clause 4.8,Table 2 ,Sl No vii) (Bacillus cereus)	-
Clause 4.8,Table 2 ,Sl No viii) (Sulphite reducing clostridia)	-
Clause 4.8,Table 2 ,Sl No ix) (Escherichia coli)	-
Clause 4.8,Table 1 ,Sl No i) (Moisture)	-
Clause 4.8,Table 1 ,Sl No iii) (Total Fat)	-

-
500 gm x 3 Excluding Vitamin A,Vitamin D,Vitamin E ,Vitamin K, Vitamin C,Thiamine,Riboflavin, Niacin,Vitamin B6 (pyridoxine),Dietary Folate equivalent , Pantothenic acid,Vitamin B12,Biotin,Choline, Iron, Sodium , Potassium, Chloride ,Calcium ,Potassim,Iodine,Copper,zinc,Manganese, Selenium,Lead,Arsenic,Tin, Cadmium,Melamine,Phosphorus, Magnesium,Inositol, Taurine,Essential amino acids

139

IS 14433 (2022)

INFANT MILK SUBSTITUTES - SPECIFICATION (Second Revision of IS 14433)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 5.10,Table 3, Sl No i) (Aerobic plate count)	-
Clause 5.10,Table 3, ,Sl No iii) (Staphylococcus aureus)	-
"5.10 Table 3 (v)" (Listeria monocytogenes-IS 14988 (Part 1))	-
"5.10 Table 3 (vi)" (Bacillus cereus-IS 5887 (Part 6))	-
"5.10 Table 3 (vii)" (Sulphite reducing clostridia-ISO 15213)	-
"5.10 Table 3 (i)" (Enterobacteriacae-is 17112(p-1))	-
Clause 5.7 and 5.10, Table 2 ,Sl No i) (Moisture)	-
Clause 5.7 and 5.10, Table 2 ,Sl No ii) (a) Total protein, including milk fat b) Milk fat)	-
Clause 5.7 and 5.10, Table 2 ,Sl No iii) (Fat, a) Total fat, including milk fat (for type II))	-
Clause 5.7 and 5.10, Table 2 ,Sl No iii) (b) Milk fat)	-
Clause 5.7 and 5.10, Table 2 ,Sl No iv) (a) Linoleic acid)	-
Clause 5.7 and 5.10, Table 2 ,Sl No iv) (b) α-Linoleic acid)	-
Clause 5.7 and 5.10, Table 2 ,Sl No v) (Carbohydrates)	-
Clause 5.7 and 5.10, Table 2 ,Sl No vi) (Total ash)	-
Clause 5.7 and 5.10, Table 2 ,Sl No vii) (Acid insoluble ash)	-
Clause 5.7 and 5.10, Table 2 ,Sl No viii) (Solubility index)	-
Clause 5.7 and 5.10, Table 2 ,Sl No xxiii) (Iron)	-
Clause 5.7 and 5.10, Table 2 ,Sl No xxiv) (Sodium)	-
Clause 5.7 and 5.10, Table 2 ,Sl No xxv) (Potassium)	-
Clause 5.12, Table 4, Table 2 ,Sl No iv) (Cadmium)	-
Clause 5.12, Table 4, Table 2 ,Sl No ii) (Arsenic)	-
Clause 5.7 and 5.10, Table 2 ,Sl No xxvi) (Chloride)	-
Clause 5.7 and 5.10, Table 2 ,Sl No xxix) (Calcium : Phosphorous ratio)	-

-
500*3, Excluding Vitamin A,Vitamin D,Vitamin E ,Vitamin K, Vitamin C,Thiamine,Riboflavin, Niacin,Vitamin B6 (pyridoxine),Dietary Folate equivalent , Pantothenic acid,Vitamin B12,Biotin,Choline, Iron, Sodium , Potassium, Chloride ,Calcium ,Potassium,Iodine,Copper,zinc,Manganese, Selenium,Lead,Arsenic,Tin, Cadmium,Melamine, Magnesium,Phosphorus

140

IS 14333 (2022)

Polyethylene Pipes for Sewerage and Industrial Chemicals and Effluent ï¿½ Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8.3 (Carbon black content- IS 2530-1963)	-
8.3 (Carbon black content Dispersion- IS 2530-1963)	-
5.2.1,T2 ("Volatile Matter- IS 4984:2016 (Annexure-C)")	-
5.2.1,T2 (Melt Flow Rate (At 190°C /5kg)-IS 2530:1963)	-
7.4,T3 of IS 4984 (Outside Diameter-IS 4984-2016)	-
7.2 (Length- IS 14333-2022)	-
7.4,T4 of IS 4984 (wall Thickness-IS 4984-2016)	-

-
Excluding Oxidation induction time, Cl 8.6 Density, Cl 8.7 Tensile strength for butt fusion, Cl 8.8 Tensile properties(Annex Hof IS 4984:2016),Cl 8.9 Slow crack growth rate

141

IS 15658 (2021)

Concrete Paving Blocks - Specification ( First Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 7.3 & 9.1.4, Table 3, SI No. (i) b) (Water absorption (Average of three test specimens))	-
Clause 7.2 & 9.1.3, Table 2, SI No. (ix) (Deviation from squareness)	-
Clause 7.2, Table No. 2, SI No. (ii) (Length, L)	-
Clause 7.3, Annex G (Average Breaking Load)	-
Clause 7.3, Annex G (Individual Breaking Load)	-
Clause 7.3, Annex F (Average Failure Load per unit Length)	-
Clause 7.3 & 9.1.4, Table 3, SI No. (v) b) (Average Flexural strength )	-
Clause 7.3 & 9.1.4, Table 3, SI No. (v) a) (Indivdual Flexural strength )	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iv) b) (Average Tensile splitting strength )	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iv) a) (Indivdual Tensile splitting strength )	-
Clause 7.3 & 9.1.4, Table 3, SI No. (ii) b) (Compressive strength (Average of eight test specimens))	-
Clause 7.3 & 9.1.4, Table 3, SI No. (ii) a) ( Indivdual Compressive strength)	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) a) ii) (Dry Abrasion resistance (Average of three test specimens))	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) b) i) ( Indivdual Wet Abrasion Resistance )	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) b) ii) (Wet Abrasion resistance (Average of three test specimens))	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) a) i) ( Indivdual Dry Abrasion Resistance )	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) a) ii) (Dry Abrasion resistance (Average of three test specimens))	-

-
complete facility

142

IS 2791 (2022)

SOLUBLE COFFEE POWDER - SPECIFICATION (FOURTH REVISION OF IS 2791)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.3, Table 1 (i) (Moisture -IS 16029)	-
3.6.2.1 (Free from infestation - IS 2791)	-

-
500 gm x 3 Excluding 1-Caffeine content 2- Copper cntent

143

IS 208 (2020)

Door Handles - Specification ( Sixth Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.2 (Tolerance)	-
5.1 (MANUFACTURE- General)	-
6.1 Table2A & 2B and Fig 1,2,3,4 (DIMENSIONS - Size 1. No. in each Lug 2. No. in a plate when a continious plate is used 3. Size Designation of Counter-sunk Head Wood Screws (as per IS 6760: 1972))	-
6.1 Table2A & 2B and Fig 1,2,3,4 (DIMENSIONS - Size (A,B,C,D,E,F,G,H,I))	-
4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981) (Chemical composition - Zinc- IS 2600:1964)	-
4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981) (Chemical composition - Impurities-Nickel- IS 2600:1964)	-
4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981) (Chemical composition - Impurities-Thallium and Indium- IS 2600:1964)	-
4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981) (Chemical composition - Impurities-Tin- IS 2600:1964)	-
4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981) (Chemical composition - Impurities-Cadmium- IS 2600:1964)	-

-
Test facility is available for material test only as per Table 1. Grade of material as per Table 1 may please be declared. Sample dia > 3mm or thickness > 0.8 mm can only be tested, Sample size 5 pcs 5x5 cm. Excluding Coating test; Cl.8.2 Corrosion Test & Cl.8.3 Anodizing Test

144

IS 5518 (1996)

Steels for die blocks for drop forging - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 (Freedom from defects)	-
9 (Hardness)	-
12 (Dimensional Tolerances)	-
14 (Ultasonic Test)	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2 (Molybdenum)	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2 (Nickel )	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2 (Chromium)	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2 (Phosphorus)	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2 (Sulphur)	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2 (Silicon)	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2 (Manganese)	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2 (Carbon)	-

-
Sample dia > 3mm or thickness > 0.8 mm can only be tested. Steel designation may please be declared. Excluding Ultrasonic test

145

IS 12817 (2020)

Stainless Steel Butt Hinges - Specification ( Third Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 4.1.2 (Silicon (Pin) )	-
Clause 4.1.2 (Phosphorus (Pin) )	-
Clause 4.1.2 (Sulphur (Pin) )	-
Clause 4.1.2 (Manganese (Pin) )	-
Clause 4.1.2 (Carbon (Pin) )	-
Clause 4.1.1 (Silicon (Flap) )	-
Clause 4.1.1 (Phosphorus (Flap) )	-
Clause 4.1.1 (Sulphur (Flap) )	-
Clause 4.1.1 (Manganese (Flap) )	-
Clause 4.1.1 (Carbon (Flap) )	-
6.2, Table 1 to 6 (Length , A -IS 12817)	-
6.2, Table 1 to 6 (Breadth, B-IS 12817)	-
6.2, Table 1 to 6 (Thickness of flap, C-IS 12817)	-
6.2, Table 1 to 6 (Dia. of Hinge pin, D-IS 12817 )	-
6.2, Table 1 to 6 (Holes for Screw Number- IS 12817 )	-
7.1 (General - IS 12817 )	-
7.2 (Knuckles - IS 12817 )	-
7.3 (Pins- IS 12817 )	-
7.4 (Screw Holes- IS 12817 )	-
7.4.2 (Position of screw holes - IS 12817 )	-
7.4.2, Fig 1 (The distance of the screw holes from the end of the flap - IS 12817 )	-
8.0 (Finish - IS 12817 )	-
As per Cl.4 (Nitrogen)	-
As per Cl.4 (Aluminium)	-
As per Cl.4 (Chromium)	-
As per Cl.4 (Vanadium)	-
As per Cl.4 (Molybdenum)	-
As per Cl.4 (Niobium)	-
As per Cl.4 (Nickel)	-
As per Cl.4 (Copper)	-
As per Cl.4 (Titanium)	-
As per Cl.4 (Zirconium)	-
As per Cl.4 (Tungsten)	-
As per Cl.4 (Cerium)	-

-
-

146

IS 15500 : PART 8 (2021)

Deepwell Handpumps, Components and Secial Tools — Specification Part 8 Handpumps

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3 (CONSTRUCTION)	-
5 (TESTING)	-

-
5 pcs of 5x5 cm sample having dia > 3mm and/or thickness > 0.8 mm shall be provided

147

IS 15500 : PART 7 (2021)

Deepwell Handpumps, Components and Secial Tools — Specification Part 7 Handpumps

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2 (CONSTRUCTION)	-
3 (TESTING)	-

-
5 pcs of 5x5 cm sample having dia > 3mm and/or thickness > 0.8 mm shall be provided.

148

IS 15500 : PART 6 (2021)

Deepwell Handpumps, Components and Secial Tools — Specification Part 6 Handpumps

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Fig. 6.1 (Brass Liner)	-
Fig. 6.2 ("Plunger Yoka Body (for SDWP, EDWP, VLOM 65 and FLP)")	-
Fig. 6.3 (Upper Valve (for SDWP, EDWP, VLOM 65 and FLP))	-
Fig. 6.4 (" Bucket Spacer-Standard (for SDWP, EDWP, VLOM 65 and FLP)")	-
Fig. 6.5 ("Bucket Spacer-Lower (for EDWP)")	-
Fig. 6.6 (Follower (SDWP and FLP))	-

-
5 pcs of 5x5 cm sample having dia > 3mm and/or thickness > 0.8 mm shall be provided

149

IS 15500 : PART 5 (2021)

Deepwell Handpumps, Components and Secial Tools — Specification Part 5 Handpumps

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Fig. 5.1 (Cylinder Body-Standard (for SDWP and FLP))	-
Fig. 5.2 (Cylinder Body-Long (for EDWP and VLOM 65))	-
Fig. 5.3 (Cylinder Body-VLOM 50)	-

-
5 pcs of 5x5 cm sample having dia > 3mm and/or thickness > 0.8 mm shall be provided. Excluding Thread Dimensions

150

IS 15500 : PART 4 (2021)

Deepwell Handpumps, Components and Secial Tools — Specification Part 4 Handpumps

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2 (CONSTRUCTION)	-
3 (TESTING)	-

-
5 pcs of 5x5 cm sample having dia > 3mm and/or thickness > 0.8 mm shall be provided. Excluding Thread Dimensions

First
Prev
4
5
6
7
Next
Last

Bureau of Indian Standards

The National Standards Body of India

BIS, Central Laboratory (CL)

20/9, Site 4, Sahibabad Industrial Area, Sahibabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201010

- sample@bis.gov.in

Scope List