BIS - LIMS (Laboratory Information Management System)

JBS TESTING SOLUTIONS PVT LTD (27), JALANDHAR

PLOT NO. 27, STREET NO. 2, ADJOINING FOCAL POINT ROAD, TRANSPORT NAGAR, JALANDHAR, PUNJAB, JALANDHAR, Jalandhar, Punjab, 144004

9988862929 jbstestingsolutions@gmail.com

Scope List

Reset

282 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

181

IS 1997 (2008)

Laboratory glassware - Burettes (Third Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11(Markings )	-	12000	For complete testing
5.1(Class of Accuracy)	-	12000	For complete testing
5.2(Types)	-	12000	For complete testing
6.1(Maximum permissible errors)	-	12000	For complete testing
8(Construction)	-	12000	For complete testing
Table 2(i) Scale length )	-	12000	For complete testing
Table 3( ii) Overall length )	-	12000	For complete testing
Table 4(iii) Distance of Zero line from top of burette )	-	12000	For complete testing
Table 5(iv) Distance of lowest graduation line from the top of stopcock )	-	12000	For complete testing
Table 6(v) Length of tube of uniform bore below graduation line )	-	12000	For complete testing
Table 7(vi) Distance of end of jet from underside of stopcock )	-	12000	For complete testing
8.2( c) Top of burette )	-	12000	For complete testing
8.3(d) Stopcock and similar devices)	-	12000	For complete testing
8.4(e) Stop Cock Leakage)	-	12000	For complete testing
8.5( f) Delivery jet)	-	12000	For complete testing
8.6(g) Delivery time )	-	12000	For complete testing
8.6(g) Delivery time )	-	12000	For complete testing
9(Graduations, figuring and patterns )	-	12000	For complete testing
9.1(a) Graduations patterns )	-	12000	For complete testing
9.2(Position of graduation line)	-	12000	For complete testing
9.3(c) Marking of graduation lines )	-	12000	For complete testing
12(. Visibility of graduation line)	-	12000	For complete testing
11(Markings )	-	12000	For complete testing
5.1(Class of Accuracy)	-	12000	For complete testing
5.2(Types)	-	12000	For complete testing
6.1(Maximum permissible errors)	-	12000	For complete testing
8(Construction)	-	12000	For complete testing
Table 2(i) Scale length )	-	12000	For complete testing
Table 3( ii) Overall length )	-	12000	For complete testing
Table 4(iii) Distance of Zero line from top of burette )	-	12000	For complete testing
Table 5(iv) Distance of lowest graduation line from the top of stopcock )	-	12000	For complete testing
Table 6(v) Length of tube of uniform bore below graduation line )	-	12000	For complete testing
Table 7(vi) Distance of end of jet from underside of stopcock )	-	12000	For complete testing
8.2( c) Top of burette )	-	12000	For complete testing
8.3(d) Stopcock and similar devices)	-	12000	For complete testing
8.4(e) Stop Cock Leakage)	-	12000	For complete testing
8.5( f) Delivery jet)	-	12000	For complete testing
8.6(g) Delivery time )	-	12000	For complete testing
8.6(g) Delivery time )	-	12000	For complete testing
9(Graduations, figuring and patterns )	-	12000	For complete testing
9.1(a) Graduations patterns )	-	12000	For complete testing
9.2(Position of graduation line)	-	12000	For complete testing
9.3(c) Marking of graduation lines )	-	12000	For complete testing
12(. Visibility of graduation line)	-	12000	For complete testing
11(Markings )	-	12000	For complete testing
5.1(Class of Accuracy)	-	12000	For complete testing
5.2(Types)	-	12000	For complete testing
6.1(Maximum permissible errors)	-	12000	For complete testing
8(Construction)	-	12000	For complete testing
Table 2(i) Scale length )	-	12000	For complete testing
Table 3( ii) Overall length )	-	12000	For complete testing
Table 4(iii) Distance of Zero line from top of burette )	-	12000	For complete testing
Table 5(iv) Distance of lowest graduation line from the top of stopcock )	-	12000	For complete testing
Table 6(v) Length of tube of uniform bore below graduation line )	-	12000	For complete testing
Table 7(vi) Distance of end of jet from underside of stopcock )	-	12000	For complete testing
8.2( c) Top of burette )	-	12000	For complete testing
8.3(d) Stopcock and similar devices)	-	12000	For complete testing
8.4(e) Stop Cock Leakage)	-	12000	For complete testing
8.5( f) Delivery jet)	-	12000	For complete testing
8.6(g) Delivery time )	-	12000	For complete testing
8.6(g) Delivery time )	-	12000	For complete testing
9(Graduations, figuring and patterns )	-	12000	For complete testing
9.1(a) Graduations patterns )	-	12000	For complete testing
9.2(Position of graduation line)	-	12000	For complete testing
9.3(c) Marking of graduation lines )	-	12000	For complete testing
12(. Visibility of graduation line)	-	12000	For complete testing
7(Material)	-	12000	For complete testing
11(Markings )	-	-	-
5.1(Class of Accuracy)	-	-	-
5.2(Types)	-	-	-
6.1(Maximum permissible errors)	-	-	-
8(Construction)	-	-	-
Table 2(i) Scale length )	-	-	-
Table 3( ii) Overall length )	-	-	-
Table 4(iii) Distance of Zero line from top of burette )	-	-	-
Table 5(iv) Distance of lowest graduation line from the top of stopcock )	-	-	-
Table 6(v) Length of tube of uniform bore below graduation line )	-	-	-
Table 7(vi) Distance of end of jet from underside of stopcock )	-	-	-
8.2( c) Top of burette )	-	-	-
8.3(d) Stopcock and similar devices)	-	-	-
8.4(e) Stop Cock Leakage)	-	-	-
8.5( f) Delivery jet)	-	-	-
8.6(g) Delivery time )	-	-	-
8.6(g) Delivery time )	-	-	-
9(Graduations, figuring and patterns )	-	-	-
9.1(a) Graduations patterns )	-	-	-
9.2(Position of graduation line)	-	-	-
9.3(c) Marking of graduation lines )	-	-	-
12(. Visibility of graduation line)	-	-	-
11(Markings )	-	-	-
5.1(Class of Accuracy)	-	-	-
5.2(Types)	-	-	-
6.1(Maximum permissible errors)	-	-	-
8(Construction)	-	-	-
Table 2(i) Scale length )	-	-	-
Table 3( ii) Overall length )	-	-	-
Table 4(iii) Distance of Zero line from top of burette )	-	-	-
Table 5(iv) Distance of lowest graduation line from the top of stopcock )	-	-	-
Table 6(v) Length of tube of uniform bore below graduation line )	-	-	-
Table 7(vi) Distance of end of jet from underside of stopcock )	-	-	-
8.2( c) Top of burette )	-	-	-
8.3(d) Stopcock and similar devices)	-	-	-
8.4(e) Stop Cock Leakage)	-	-	-
8.5( f) Delivery jet)	-	-	-
8.6(g) Delivery time )	-	-	-
8.6(g) Delivery time )	-	-	-
9(Graduations, figuring and patterns )	-	-	-
9.1(a) Graduations patterns )	-	-	-
9.2(Position of graduation line)	-	-	-
9.3(c) Marking of graduation lines )	-	-	-
12(. Visibility of graduation line)	-	-	-
11(Markings )	-	-	-
5.1(Class of Accuracy)	-	-	-
5.2(Types)	-	-	-
6.1(Maximum permissible errors)	-	-	-
8(Construction)	-	-	-
Table 2(i) Scale length )	-	-	-
Table 3( ii) Overall length )	-	-	-
Table 4(iii) Distance of Zero line from top of burette )	-	-	-
Table 5(iv) Distance of lowest graduation line from the top of stopcock )	-	-	-
Table 6(v) Length of tube of uniform bore below graduation line )	-	-	-
Table 7(vi) Distance of end of jet from underside of stopcock )	-	-	-
8.2( c) Top of burette )	-	-	-
8.3(d) Stopcock and similar devices)	-	-	-
8.4(e) Stop Cock Leakage)	-	-	-
8.5( f) Delivery jet)	-	-	-
8.6(g) Delivery time )	-	-	-
8.6(g) Delivery time )	-	-	-
9(Graduations, figuring and patterns )	-	-	-
9.1(a) Graduations patterns )	-	-	-
9.2(Position of graduation line)	-	-	-
9.3(c) Marking of graduation lines )	-	-	-
12(. Visibility of graduation line)	-	-	-
7(Material)	-	-	-

-
Included w.e.f 05.05.2025

182

IS 14276 (2016)

Cement bonded particle boards - Specification (First Revision)

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Finish)	-	14000	For complete testing
7(Dimensions and Tolerances)	-	14000	For complete testing
8.5(Workability)	-	14000	For complete testing
10.3, Table-1(Test for Density)	-	14000	For complete testing
10.5, Table-1(Test for Water Absorption)	-	14000	For complete testing
10.6, Table-1(Test for swelling in water)	-	14000	For complete testing
10.7, Table-1(Test for modulus of Rupture)	-	14000	For complete testing
10.8, Table-1(Test for modulus of Elasticity)	-	14000	For complete testing
10.9, Table-1(Test for tensile strength perpendicular to Surface)	-	14000	For complete testing
10.1, Table-1(Test for Screw Withdrawal Strength)	-	14000	For complete testing
Clause 8.2 Table 1(Moisture content)	-	14000	For complete testing

-
Included w.e.f 05.05.2025

183

IS 1239 : Part 1 (2004)

Steel Tubes, Tubulars and Other Wrought Steel Fittings : Part 1 Steel Tubes (BI-LINGUAL)

sizes upto and including 100 mm, Black and Galvanised

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
12 AND AS PER IS 4736(UNIFORMITY OF ZINC COATING)	-	500	For uniformity/ Mass of Zinc coating
12 AND AS PER IS 4736(MASS OF ZINC COATING)	-	500	For uniformity/ Mass of Zinc coating
6.2 AND AS PER IS 513(NITROGEN)	-	2000	For complete chemical analysis
6.2 AND AS PER IS 513(CARBON)	-	2000	For complete chemical analysis
6.2 AND AS PER IS 513(SILICON)	-	2000	For complete chemical analysis
6.2 AND AS PER IS 513(MANGANESE)	-	2000	For complete chemical analysis
6.2 AND AS PER IS 513(PHOSPHORUS)	-	2000	For complete chemical analysis
Cl. 15(Workmanship)	-	500	For complete workmanship
Cl. 14.3(Flattening test (Over 50 mm NB))	-	1500	For complete Cl 14
Cl. 14.2(Bend Test (uto and including 50 mm NB))	-	1500	For complete Cl 14
Cl. 14.1.1(Elongation)	-	3000	For complete Cl 14
Cl. 14.1(Tensile Strength)	-	3000	For complete Cl 14
Cl. 3.3, 10.2(Plain End)	-	500	For complete Cl 3 and Cl 10
Cl. 11(Length)	-	3000	For Complete Cl 8 , Cl 9 and Cl 11
Cl. 8, 9 Table 3,4 & 5(Mass of Tube)	-	3000	For Complete Cl 8 , Cl 9 and Cl 11
Cl. 6.5(Height of Internal Fin)	-	3000	For Complete Cl 8 , Cl 9 and Cl 11
Cl. 8, 9 Table 3,4 & 5(Thickness)	-	3000	For Complete Cl 8 , Cl 9 and Cl 11
Cl. 8 Table 3,4 & 5(Outside Diameter)	-	3000	For Complete Cl 8 , Cl 9 and Cl 11
Clause 14.1.1(Elongation Percent)	-	3000	For Complete Cl 14
Clause 11.3(Approximate Length)	-	3000	For Complete Cl 8 , Cl 9 and Cl 11
Clause 11.2(Exact Length)	-	3000	For Complete Cl 8 , Cl 9 and Cl 11
Clause 11.1(Random Length)	-	3000	For Complete Cl 8 , Cl 9 and Cl 11
Clause 8.1 (Table3,4,5)(Nominal Bore )	-	3000	For Complete Cl 8 , Cl 9 and Cl 11
Cl 15(Workmanship)	-	500	For Complete Cl 15
Cl 10.1.1(Manufacturing )	-	500	For Complete Cl 10
Cl 10.1(Manufacturing )	-	500	For Complete Cl 10
cl.17(MARKING)	-	500	For Complete Cl 17
6.2 AND AS PER IS 513(MICRO ALLOY)	-	2000	For Complete Chemical testing, if required
6.2 AND AS PER IS 10748(COPPER)	-	2000	For Complete Chemical testing, if required
6.2 AND AS PER IS 513(ALUMINIUM)	-	2000	For Complete Chemical testing, if required
6.2 AND AS PER IS 10748(NITROGEN)	-	2000	For Complete Chemical testing, if required
6.2 AND AS PER IS 10748(MICRO ALLOY)	-	2000	For Complete Chemical testing, if required
6.2 AND AS PER IS 10748(ALUMINIUM)	-	2000	For Complete Chemical testing, if required
6.2 AND AS PER IS 10748(SILICON)	-	2000	For Complete Chemical testing, if required
6.2 AND AS PER IS 10748(CARBON EQUIVALENT)	-	2000	For Complete Chemical testing, if required
6.2 AND AS PER IS 10748(MANGANESE)	-	2000	For Complete Chemical testing, if required
6.2 AND AS PER IS 10748(PHOSPHORUS)	-	2000	For Complete Chemical testing, if required
6.2 AND AS PER IS 10748(SULPHUR)	-	2000	For Complete Chemical testing, if required
6.2 AND AS PER IS 10748(CARBON)	-	2000	For Complete Chemical testing, if required
Clause - 6.1.1, Table-1( ALUMINIUM)	-	2000	For Complete Chemical testing, if required
Clause - 6.1.1, Table-1(SILICON)	-	2000	For Complete Chemical testing, if required
Clause - 6.1.1, Table-1(NITROGEN)	-	2000	For Complete Chemical testing, if required
Clause - 6.1.1, Table-1(MANGANESE)	-	2000	For Complete Chemical testing, if required
Clause - 6.1.1, Table-1(PHOSPHURS)	-	2000	For Complete Chemical testing, if required
Clause - 6.1.1, Table-1(SULPHUR)	-	2000	For Complete Chemical testing, if required
Clause - 6.1.1, Table-1( CARBON)	-	2000	For Complete Chemical testing, if required
Cl. 6.1.1, table1 of IS 1239(Part1)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	2000	For Complete Chemical testing, if required
Cl. 6.1.1, table1 of IS 1239(Part1)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	2000	For Complete Chemical testing, if required
Cl. 6.1.1, table1 of IS 1239(Part1)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	2000	For Complete Chemical testing, if required
Cl. 6.1.1, table1 of IS 1239(Part1)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	2000	For Complete Chemical testing, if required

-
-

184

IS 8931 (2021)

Copper alloy single taps, combination tap assemblies, stop valves and single lever mixers for water services Specification (second revision)

All types and all Sizes

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4(Classfication)	-	3500	For complete Cl. 4 and 6
Cl 4(Classfication)	-	3500	For complete Cl. 4 and 6
Cl 6.1(Manufacture,Workmanship & Construction)	-	3500	For complete Cl. 4 and 6
Cl 6.5(Manufacture,Workmanship & Construction)	-	3500	For complete Cl. 4 and 6
Cl 6.6(Manufacture,Workmanship & Construction)	-	3500	For complete Cl. 4 and 6
Cl 6.7(Manufacture,Workmanship & Construction)	-	3500	For complete Cl. 4 and 6
Cl 6.8(Manufacture,Workmanship & Construction)	-	3500	For complete Cl. 4 and 6
Cl 6.9(Manufacture,Workmanship & Construction)	-	3500	For complete Cl. 4 and 6
Cl 6.10(Manufacture,Workmanship & Construction)	-	3500	For complete Cl. 4 and 6
Cl 6.11(Manufacture,Workmanship & Construction)	-	3500	For complete Cl. 4 and 6
Cl 6.12(Manufacture,Workmanship & Construction)	-	3500	For complete Cl. 4 and 6
Cl 6.13(Manufacture,Workmanship & Construction)	-	3500	For complete Cl. 4 and 6
Cl 7(DIMENSIONS)	-	10000	For complete Cl. 4 and 6
Cl 7(DIMENSIONS)	-	10000	For complete Cl. 7
Cl 7(DIMENSIONS)	-	10000	For complete Cl. 7
Cl 7(DIMENSIONS)	-	10000	For complete Cl. 7
Cl 7(DIMENSIONS)	-	10000	For complete Cl. 7
Cl 8(ADDITIONAL REQUIREMENTS FOR ACCESSIBLE TAPS)	-	4500	Additional if required
Cl 10(PERFORMANCE REQUIREMENTS)	-	20000	For complete Cl. 10.except optional, if any
Cl 10(PERFORMANCE REQUIREMENTS)	-	20000	For complete Cl. 10.except optional, if any
Cl 10(PERFORMANCE REQUIREMENTS)	-	20000	For complete Cl. 10.except optional, if any
Cl 10(PERFORMANCE REQUIREMENTS)	-	20000	For complete Cl. 10.except optional, if any
Cl 10(PERFORMANCE REQUIREMENTS)	-	20000	For complete Cl. 10., except optional, if any
Cl 11(ADDITIONAL REQUIREMENTS FOR WATER EFFICIENCY)	-	15000	For complete Cl. 11
As per Table-1(Carbon)	-	4500	For complete chemical test (additional charges for extra elements, if required)
As per Table-1(Sulphur)	-	4500	For complete chemical test (additional charges for extra elements, if required)
As per Table-1(Phosphorus)	-	4500	For complete chemical test (additional charges for extra elements, if required)
As per Table-1(Manganese)	-	4500	For complete chemical test (additional charges for extra elements, if required)
As per Table-1(Nitrogen)	-	4500	For complete chemical test (additional charges for extra elements, if required)
As per Table-1(Silicon)	-	4500	For complete chemical test (additional if required)
As per Table-1(Aluminium)	-	4500	For complete chemical test (additional if required)
As per Table-1(Chromium)	-	4500	For complete chemical test (additional if required)
As per Table-1(Vanadium)	-	4500	For complete chemical test (additional if required)
As per Table-1(Molybdenum)	-	4500	For complete chemical test (additional if required)
As per Table-1(Iron)	-	4500	For complete chemical test (additional if required)
As per Table-1(Nickel)	-	4500	For complete chemical test (additional if required)
As per Table-1(Copper)	-	4500	For complete chemical test (additional if required)
As per Table-1(Zinc)	-	4500	For complete chemical test (additional if required)
As per Table-1(Lead)	-	4500	For complete chemical test ((additional charges for extra elements, if required)
As per Table-1(Boron)	-	4500	For complete chemical test (additional charges for extra elements, if required)

-
-

185

IS 15380 (2023)

MOULDED HIGH DENSITY FIBRE HDF PANELLED DOOR SHUTTERS - SPECIFICATION ( First Revision )

24100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.1(Sized)	-	24100	For complete testing
Cl-6.1.2(Moisture content in timbers)	-	24100	For complete testing
Cl-6.2 S.No (1), i(Density, kg/m3 , Min)	-	24100	For complete testing
Cl-6.2 S.No (1), ii(Moisture content, percent, Max)	-	24100	For complete testing
Cl-6.2 S.No (1), iii(Water absorption, percent, Max)	-	24100	For complete testing
Cl-6.2 S.No (1), iv(Swelling in water, percent, Max)	-	24100	For complete testing
Cl-6.2 S.No (1), v(Modulus of rupture, N/mm2 , Min)	-	24100	For complete testing
Cl-6.2 S.No (1), vi(Internal bond strength, N/mm2 , Min)	-	24100	For complete testing
Cl-6.2 S.No (1), vii(Immersion in boiling water at (100 ± 3) °C for 4 h)	-	24100	For complete testing
Cl-6.2 S.No (1), viii(Formaldehyde emission, mg/100 g, Max)	-	24100	For complete testing
Cl- 6.3(Particle Boards as Core)	-	24100	For complete testing
Cl- 6.4(Adhesive)	-	24100	For complete testing
Cl- 6.5(Laminated veneer lumber (LVL), veneer laminated lumber (VLL), Medium Density Fibre (MDF))	-	24100	For complete testing
Cl-11.1(Dimensions and Squareness Test)	-	24100	For complete testing
Cl-11.2(General Flatness Test)	-	24100	For complete testing
Cl-11.3(Local Planeness Test)	-	24100	For complete testing
Cl-11.4(Impact Indentation Test)	-	24100	For complete testing
Cl-11.5(Flexure Test)	-	24100	For complete testing
Cl-11.6(Edge Loading Test)	-	24100	For complete testing
Cl-11.7(Shock Resistance Test)	-	24100	For complete testing
Cl-11.8(Buckling Resistance Test)	-	24100	For complete testing
Cl-11.9(Slamming Test)	-	24100	For complete testing
Cl-11.10(Misuse Test)	-	24100	For complete testing
Cl-11.11(Varying Humidity Test)	-	24100	For complete testing
Cl-11.12(End Immersion Test)	-	24100	For complete testing
Cl-11.13(Glue Adhesion Test)	-	24100	For complete testing
Cl-11.14(Screw Withdrawal Resistance Test)	-	24100	For complete testing
Cl-12.2(Sample Size)	-	24100	For complete testing
Cl-14(Marking)	-	24100	For complete testing
Cl-6.1.1(Bulk density of timber)	-	24100	For complete testing
Cl-9(Workmanship and finish)	-	24100	For complete testing

-
Included w.e.f 05.05.2025

186

IS 1786 (2008)

High strength deformed steel bars and wires for concretere inforcement - Specification (Fourth Revision)

For all sizes and Grades as per IS 1786

10800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 6.1(Length, Width & Thickness)	-	3000	For Cl 6 & 7 testing charges
Cl 7.2(Weight)	-	3000	For Cl 6 & 7 testing charges
Cl 5(Deformations and Surface Characteristics)	-	2000	For Complete Cl 5
Cl 8.1(UTM)	-	3000	For Cl 8 & 9 testing charges, , For Pull out - 8500
Cl 9.3(Load In One Direction)	-	3000	For Cl 8 & 9 testing charges
Cl 9.4(Load In Other Direction From Bend)	-	3000	For Cl 8 & 9 testing charges
Cl. 8.1 Table 3(Elongation, percentage)	-	3000	For Cl 8 & 9 testing charges
Cl. 8.1 Table 3(TS/YS ratio)	-	3000	For Cl 8 & 9 testing charges
Cl. 8.1 Table 3(Tensile Strength (TS))	-	3000	For Cl 8 & 9 testing charges
Cl. 8.1 Table 3(Yield Stress (YS))	-	3000	For Cl 8 & 9 testing charges
Cl. 7.2 Table -2 (Nominal Mass)	-	3000	For Cl 6 & 7 testing charges
Cl. 6.1(Nominal Size)	-	3000	For Cl 6 & 7 testing charges
Cl. 5 (Cl. 5 - Mean projected area of transverse ribs (1/3 of Ar))	-	2000	For Complete Cl 5
4.1(Sulphur and phosphorous)	-	2800	For Complete Chemical Testing, if required
4.1(CE)	-	2800	For Complete Chemical Testing, if required
4.1( Nitrogen%)	-	2800	For Complete Chemical Testing, if required
4.1(Ni)	-	2800	For Complete Chemical Testing, if required
4.1(Mo)	-	2800	For Complete Chemical Testing, if required
4.1(Cr)	-	2800	For Complete Chemical Testing, if required
4.1( Ti)	-	2800	For Complete Chemical Testing, if required
4.1(V)	-	2800	For Complete Chemical Testing, if required
4.1( Nb)	-	2800	For Complete Chemical Testing, if required
4.1( Aluminium %)	-	2800	For Complete Chemical Testing, if required
4.1( Copper %)	-	2800	For Complete Chemical Testing, if required
4.1(Silicon %)	-	2800	For Complete Chemical Testing, if required
4.1(Sulphur %)	-	2800	For Complete Chemical Testing, if required
4.1(Manganese %)	-	2800	For Complete Chemical Testing, if required
4.1(Carbon %)	-	2800	For Complete Chemical Testing, if required
Cl. 5 (Cl.5 Mean area of ribs/unit length (Ar), )	-	2000	For Complete Cl 5
Cl. 8.1 Table 3(Total Elongation at Maximum Force)	-	3000	For Complete Cl 8 and Cl 9
5.7(PullOut (Bond Test))	-	11800	For Pull out test
Cl. 5.7(Average compressive strength of cubes at 28 days)	-	11800	For Pull out test
Cl. 5.7(Bond Strength at 0.25 mm slip)	-	11800	For Pull out test
Cl. 5.7(Date of testing of concrete cubes)	-	11800	For Pull out test
Cl. 5.7(Date of casting of concrete cubes)	-	11800	For Pull out test
5.7(Pull-out test - IS:2770(P1))	-	11800	For Pull out test

-
-

187

IS 447 (1988)

Specification for rubber hose for welding (Fourth Revision)

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Classification - IS 444)	-	8000	For complete testing
5(Lining - IS 444)	-	8000	For complete testing
5(Reinforcement - IS 444)	-	8000	For complete testing
5(Cover - IS 444)	-	8000	For complete testing
5(Lining and Cover - IS 444)	-	8000	For complete testing
6.1- Table 1(Internal diameters - ISO 4671)	-	8000	For complete testing
6.2(Concentricity - ISO 4671)	-	8000	For complete testing
6.3(Length -IS 4671)	-	8000	For complete testing
6.4( thickness of the lining plus cover - ISO 4671)	-	8000	For complete testing
6.4(If the cover is fluted, the depth of the flutes - ISO 4671)	-	8000	For complete testing
7.1 - Table 2( tensile strength of Lining - ISO 37 )	-	8000	For complete testing
7.1 - Table 2( tensile strength of Cover - ISO 37 )	-	8000	For complete testing
7.1 - Table 2(elongation at break of Lining - ISO 37)	-	8000	For complete testing
7.1 - Table 2(elongation at break of Cover - ISO 37)	-	8000	For complete testing
7.1 - Table 2(Change in tensile strength of Lining from original value after ageing(max) - ISO 188 and ISO 37)	-	8000	For complete testing
7.1 - Table 2(Change in tensile strength of Cover from original value after ageing(max) - ISO 188 and ISO 37)	-	8000	For complete testing
7.1 - Table 2(Change in elongation at break of Lining from original value after ageing (max.) - ISO 188 and ISO 37)	-	8000	For complete testing
7.1 - Table 2(Change in elongation at break of Cover from original value after ageing (max.) - ISO 188 and ISO 37)	-	8000	For complete testing
7.2 - Table 3(Proof pressure at 23 °C - ISO 1402)	-	8000	For complete testing
7.2 - Table 3(Change in length at proof pressure - ISO 1402)	-	8000	For complete testing
7.2 - Table 3(Minimum burst pressure - ISO 1402)	-	8000	For complete testing
7.2 - Table 3(Adhesion between components - ISO 8033)	-	8000	For complete testing
7.2 - Table 3(Ozone resistance - ISO 7326)	-	8000	For complete testing
7.2 - Table 3(Flexibility at 23 °C - Method A of ISO 1746)	-	8000	For complete testing
7.2 - Table 3(Low-temperature flexibility - Method B of ISO 4672)	-	8000	For complete testing
Cl. 3.2 - Table 1(Bore size)	-	8000	For complete testing
Cl. 3.2 - Table 1(Lining Thickness)	-	8000	For complete testing
Cl. 3.2 - Table 1(Cover Thickness)	-	8000	For complete testing
Cl. 3.2 - Table 1(Length %)	-	8000	For complete testing
Cl. 3.3 - Table 2(Tensile strength - Lining MPA)	-	8000	For complete testing
Cl. 3.3 - Table 2(Tensile strength - Cover Mpa)	-	8000	For complete testing
Cl. 3.3 - Table 2(Elongation at break - Lining %)	-	8000	For complete testing
Cl. 3.3 - Table 2(Elongation at break - Cover %)	-	8000	For complete testing
Cl. 3.3 - Table 2(After Ageing Tensile strength - Lining %)	-	8000	For complete testing
Cl. 3.3 - Table 2(After Ageing Tensile strength - Cover %)	-	8000	For complete testing
Cl. 3.3 - Table 2(After Ageing Elongation at break - Lining %)	-	8000	For complete testing
Cl. 3.3 - Table 2(After Ageing Elongation at break - Cover %)	-	8000	For complete testing
Cl. 3.4 - Table3(Pressure Tests)	-	8000	For complete testing
Cl. 3.4 - Table3(Adhesion KN/m Min)	-	8000	For complete testing
Cl. 3.2 - Table 1(Bore size, mm)	-	8000	For complete testing
Cl. 3.2 - Table 1(Lining Thickness, mm)	-	8000	For complete testing
Cl. 3.2 - Table 1(Cover Thickness, mm)	-	8000	For complete testing
Cl. 3.2 - Table 1(Length)	-	8000	For complete testing
Cl. 3.3 - Table 2(Tensile strength - Lining, Mpa)	-	8000	For complete testing
Cl. 3.3 - Table 2(Tensile strength - Cover, Mpa)	-	8000	For complete testing
Cl. 3.3 - Table 2(Elongation at break - Lining)	-	8000	For complete testing
Cl. 3.3 - Table 2(Elongation at break - Cover)	-	8000	For complete testing
Cl. 3.3 - Table 2(After Ageing Tensile strength - Lining)	-	8000	For complete testing
Cl. 3.3 - Table 2(After Ageing Tensile strength - Cover)	-	8000	For complete testing
Cl. 3.3 - Table 2(After Ageing Elongation at break - Lining)	-	8000	For complete testing
Cl. 3.3 - Table 2(After Ageing Elongation at break - Cover)	-	8000	For complete testing
Cl. 3.4 - Table3(Pressure Tests)	-	8000	For complete testing
Cl. 3.4 - Table3(Adhesion, KN/m Min)	-	8000	For complete testing
Cl. 3.4 - Table3(Adhesion)	-	8000	For complete testing
Cl. 3.4 - Table3(Pressure Tests)	-	8000	For complete testing
Cl. 3.3 - Table 2(After Ageing Elongation at break - Cover)	-	8000	For complete testing
Cl. 3.3 - Table 2(After Ageing Elongation at break - Lining)	-	8000	For complete testing
Cl. 3.3 - Table 2(After Ageing Tensile strength - Cover)	-	8000	For complete testing
Cl. 3.3 - Table 2(After Ageing Tensile strength - Lining)	-	8000	For complete testing
Cl. 3.3 - Table 2(Elongation at break - Cover)	-	8000	For complete testing
Cl. 3.3 - Table 2(Elongation at break - Lining)	-	8000	For complete testing
Cl. 3.3 - Table 2(Tensile strength - Cover)	-	8000	For complete testing
Cl. 3.3 - Table 2(Tensile strength - Lining)	-	8000	For complete testing
Cl. 3.2 - Table 1(Length)	-	8000	For complete testing
Cl. 3.2 - Table 1(Lining Thickness)	-	8000	For complete testing
Cl. 3.2 - Table 1(Bore size)	-	8000	For complete testing
Cl. 3.2 - Table 1(Cover Thickness)	-	8000	For complete testing

-
Included w.e.f.16.07.2025

188

IS 14364 (2024)

Quaternary Ammonium Compound Based Surface Cleaner, Liquid ï¿½ Specification ( First Revision )

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(Description)	-	25000	For complete testing
Cl-4.2(Composition)	-	25000	For complete testing
Cl-4.3(Odour)	-	25000	For complete testing
Cl-4.4(Colour)	-	25000	For complete testing
Cl-4.5(Stability on Dilution)	-	25000	For complete testing
Cl-4.6(Cleaning Property)	-	25000	For complete testing
Cl-4.7(Applicability)	-	25000	For complete testing
Cl-4.8(Keeping Quality)	-	25000	For complete testing
Cl-4.8 & 4.9, Table-1 (i)(Total non-volatile matter, percent by mass, Min)	-	25000	For complete testing
Cl-4.8 & 4.9, Table-1 (ii)(pH)	-	25000	For complete testing
Cl-4.8 & 4.9, Table-1 (iii)(QAC content, percent by mass, Min)	-	25000	For complete testing
Cl-6(Marking)	-	25000	For complete testing
Cl-4.1(Description)	-	-	-
Cl-4.2(Composition)	-	-	-
Cl-4.3(Odour)	-	-	-
Cl-4.4(Colour)	-	-	-
Cl-4.5(Stability on Dilution)	-	-	-
Cl-4.6(Cleaning Property)	-	-	-
Cl-4.7(Applicability)	-	-	-
Cl-4.8(Keeping Quality)	-	-	-
Cl-4.8 & 4.9, Table-1 (i)(Total non-volatile matter, percent by mass, Min)	-	-	-
Cl-4.8 & 4.9, Table-1 (ii)(pH)	-	-	-
Cl-4.8 & 4.9, Table-1 (iii)(QAC content, percent by mass, Min)	-	-	-
Cl-6(Marking)	-	-	-

-
Included w.e.f.21.05.2025

189

IS 1367 : Part 13 (2020)

Technical Supply Conditions for Threaded Steel Fasteners Part 13 Hot Dip Galvanized Coatings on Threaded Fasteners ( Third Revision )

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1(Chemical Composition)	-	7500	For complete testing
7.0(Mechanical Propoerties ( Proof load & Tesnsile Strength))	-	7500	For complete testing
8.1(Appearance of zinc coating)	-	7500	For complete testing
8.3(Zinc coating thickness)	-	7500	For complete testing
8.4(Adhesion of Zinc Coating)	-	7500	For complete testing

-
Included w.e.f.16.07.2025

190

IS 1367 : Part 6 (2018)

Technical supply conditions for threaded steel fasteners: Part 6 mechanical properties of fasteners made of carbon steel and alloy steel - Nuts with specified property classes - Coarse thread and fine pitch thread (Fourth Revision)

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.0(Material Testing)	-	7500	For complete test
9.1(Proof Load)	-	7500	For complete test
9.2(Hardness Test)	-	7500	For complete test
9.3(Surface Integrity)	-	7500	For complete test
Cl-4.3(Ranges of nominal diameters in relation to nut style and property class)	-	7500	For complete test

-
Included w.e.f.16.07.2025

191

IS 1367 : Part 3 (2017)

Technical supply conditions for threaded steel fasteners: Part 3 mechanical properties of fasteners made of carbon steel and bolts, screws and studs (Fifth Revision)

21500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.0(Material Testing)	-	6500	For complete material tests
7.0(Mechanical testing (Ys, TS, %EL, RA))	-	10000	For complete mechanical testing and Cl 9.
9.6(Proof Load test for finished bolts scrwes, and studs)	-	10000	For complete mechanical testing and Cl 9.
9.8(Head soundness test)	-	10000	For complete mechanical testing and Cl 9.
9.9(Hardness Test)	-	1000	For hardness test
9.10(Decarburization test)	-	2500	For carb and Decarb
9.11(Carburization test)	-	2500	For carb and Decarb
9.12(Reducing of hardnes after retempering , Hv)	-	10000	For complete mechanical testing and Cl 9.
9.13(Torsional Test)	-	10000	For complete mechanical testing and Cl 9.
9.14(Impact Test)	-	10000	For complete mechanical testing and Cl 9.
9.15(Surface discounity)	-	10000	For complete mechanical testing and Cl 9.
6.0(Material Testing)	-	0	-
7.0(Mechanical testing (Ys, TS, %EL, RA))	-	0	-
9.6(Proof Load test for finished bolts scrwes, and studs)	-	0	-
9.8(Head soundness test)	-	0	-
9.9(Hardness Test)	-	0	-
9.10(Decarburization test)	-	0	-
9.11(Carburization test)	-	0	-
9.12(Reducing of hardnes after retempering , Hv)	-	0	-
9.13(Torsional Test)	-	0	-
9.14(Impact Test)	-	0	-
9.15(Surface discounity)	-	0	-
Clause 7(Mechanical and physical properties)	-	0	-
Clause 9(Test Method)	-	0	-
Clause 9.1(Tensile Test under wedge loading of finished bolts and screws (excluding studs))	-	0	-
Clause 9.2(Tensile Test for finished bolts, screws and studs for determination of tensile)	-	0	-
Clause 9.3(Tensile Test for full-size bolts, screws and studs for determination of elongation after fracture A and stress at 0,0048d non-proportional elongation)	-	0	-
Clause 9.4(Tensile Test for bolts and screws with reduced loadability due to head design)	-	0	-
Clause 9.5(Tensile test of fasteners with waisted shank)	-	0	-
Clause 9.7(Tensile test for machined test pieces)	-	0	-
Clause 10(MARKING)	-	0	-

-
-

192

IS 1367 : Part 5 (2018)

Technical supply conditions for threaded steel fasteners: Part 5 mechanical properties of fasteners made of carbon steel and alloy steel - Set screws and similar threaded fasteners with specified hardness classes - Coarse thread and fine pitch thread (Fourth Revision)

21500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.0(Material test)	-	6500	For complete Chemical testing
7.0(Mechanical Testing (Ys, Ts, %El))	-	10000	For complete mechanical testing and Cl 9.
9.1(Hardness)	-	10000	For complete mechanical testing and Cl 9.
9.2(Decarburization test)	-	2500	For carb and Decarb testing
9.3(Carburization test)	-	2500	For carb and Decarb testing
9.4(Proof Torque Test)	-	10000	For complete mechanical testing and Cl 9.
9.5(Proof Torque Test)	-	10000	For complete mechanical testing and Cl 9.
3.0(Surface Integrity)	-	10000	For complete mechanical testing and Cl 9.
6.0(Material test)	-	0	-
7.0(Mechanical Testing (Ys, Ts, %El))	-	0	-
9.1(Hardness)	-	0	-
9.2(Decarburization test)	-	0	-
9.3(Carburization test)	-	0	-
9.4(Proof Torque Test)	-	0	-
9.5(Proof Torque Test)	-	0	-
3.0(Surface Integrity)	-	0	-
Clause 7(Mechanical and physical properties)	-	0	-
Clause 8(Applicability of test method)	-	0	-
Clause 10(MARKING)	-	0	-

-
Included w.e.f.16.07.2025

193

IS 638 (2024)

SHEET RUBBER JOINTING AND RUBBER INSERTION JOINTING - SPECIFICATION (Third Revision)

19250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.1(Types)	-	19250	5000 - -For tensile and Elongation at break 3000 - For accelerated ageing 3000 - For compression set 3500 - For resistance to bending 3500 - For adhesion testing 1250 - For hardness testing
2.2(Grades)	-	19250	5000 - -For tensile and Elongation at break 3000 - For accelerated ageing 3000 - For compression set 3500 - For resistance to bending 3500 - For adhesion testing 1250 - For hardness testing
3.1.1(Jointing Material)	-	19250	5000 - -For tensile and Elongation at break 3000 - For accelerated ageing 3000 - For compression set 3500 - For resistance to bending 3500 - For adhesion testing 1250 - For hardness testing
3.1.2(Composition of Rubber Compound)	-	19250	5000 - -For tensile and Elongation at break 3000 - For accelerated ageing 3000 - For compression set 3500 - For resistance to bending 3500 - For adhesion testing 1250 - For hardness testing
3.1.3(Fabric Reinforcementfor Rubber Insertion Jointing)	-	19250	5000 - -For tensile and Elongation at break 3000 - For accelerated ageing 3000 - For compression set 3500 - For resistance to bending 3500 - For adhesion testing 1250 - For hardness testing
3.2.2(Thickness and Number of Plies)	-	19250	5000 - -For tensile and Elongation at break 3000 - For accelerated ageing 3000 - For compression set 3500 - For resistance to bending 3500 - For adhesion testing 1250 - For hardness testing
3.2.2.1(Positon of Plies)	-	19250	5000 - -For tensile and Elongation at break 3000 - For accelerated ageing 3000 - For compression set 3500 - For resistance to bending 3500 - For adhesion testing 1250 - For hardness testing
3.3(Size of Sheet Rubber Jointing and Rubber Insertion Jointing)	-	19250	5000 - -For tensile and Elongation at break 3000 - For accelerated ageing 3000 - For compression set 3500 - For resistance to bending 3500 - For adhesion testing 1250 - For hardness testing
3.4(Tensile Strength and Elongation at Break)	-	19250	5000 - -For tensile and Elongation at break 3000 - For accelerated ageing 3000 - For compression set 3500 - For resistance to bending 3500 - For adhesion testing 1250 - For hardness testing
3.5.1(Jointing to be Used for Joints Subjects to Water and Air Pressure)	-	19250	5000 - -For tensile and Elongation at break 3000 - For accelerated ageing 3000 - For compression set 3500 - For resistance to bending 3500 - For adhesion testing 1250 - For hardness testing
3.5.2(Jointing to be Used for Joints Subjected to Steam Pressure)	-	19250	5000 - -For tensile and Elongation at break 3000 - For accelerated ageing 3000 - For compression set 3500 - For resistance to bending 3500 - For adhesion testing 1250 - For hardness testing
3.6.1(Jointing to be Used for Joints Subject to Water and Air Pressure)	-	19250	5000 - -For tensile and Elongation at break 3000 - For accelerated ageing 3000 - For compression set 3500 - For resistance to bending 3500 - For adhesion testing 1250 - For hardness testing
3.6.2(Jointing to be Used for Joints Subjects to Steam Pressure)	-	19250	5000 - -For tensile and Elongation at break 3000 - For accelerated ageing 3000 - For compression set 3500 - For resistance to bending 3500 - For adhesion testing 1250 - For hardness testing
3.7(Resistance to Bending)	-	19250	5000 - -For tensile and Elongation at break 3000 - For accelerated ageing 3000 - For compression set 3500 - For resistance to bending 3500 - For adhesion testing 1250 - For hardness testing
3.8(Adhesive)	-	19250	5000 - -For tensile and Elongation at break 3000 - For accelerated ageing 3000 - For compression set 3500 - For resistance to bending 3500 - For adhesion testing 1250 - For hardness testing
3.9(Hardness)	-	19250.03	5000 - -For tensile and Elongation at break 3000 - For accelerated ageing 3000 - For compression set 3500 - For resistance to bending 3500 - For adhesion testing 1250 - For hardness testing
4(Marking and Packing)	-	19250	5000 - -For tensile and Elongation at break 3000 - For accelerated ageing 3000 - For compression set 3500 - For resistance to bending 3500 - For adhesion testing 1250 - For hardness testing
Cl- 3.2.2.2(Outer layer thickness)	-	19250	5000 - -For tensile and Elongation at break 3000 - For accelerated ageing 3000 - For compression set 3500 - For resistance to bending 3500 - For adhesion testing 1250 - For hardness testing
(clause 4.2)(Construction and Workmanship)	-	19250	5000 - -For tensile and Elongation at break 3000 - For accelerated ageing 3000 - For compression set 3500 - For resistance to bending 3500 - For adhesion testing 1250 - For hardness testing
(clause 4.4)(Tensile Strength and Elongation at Break)	-	5000	For complete tensile and elongation testing
(clause 4.5)(Accelerated Ageing)	-	3000	For complete accelerated ageing test
(clause 4.6)(Compression Set)	-	3000	For complete compression set
(clause 4.7)(Resistance to Bending)	-	3500	For complete resistance to bending
(clause 4.8)(Adhesion)	-	3500	For complete adhesion testing
(clause 4.9)(Hardness)	-	1250	For complete hardness testing
(clause 4.2)(Construction and Workmanship)	-	19250	5000 - -For tensile and Elongation at break 3000 - For accelerated ageing 3000 - For compression set 3500 - For resistance to bending 3500 - For adhesion testing 1250 - For hardness testing
(clause 4.4)(Tensile Strength and Elongation at Break)	-	5000	For complete tensile and elongation testing
(clause 4.5)(Accelerated Ageing)	-	3000	For complete accelerated ageing test
(clause 4.6)(Compression Set)	-	3000	For complete compression set
(clause 4.7)(Resistance to Bending)	-	3500	For complete resistance to bending
(clause 4.8)(Adhesion)	-	3500	For complete adhesion testing
(clause 4.9)(Hardness)	-	1250	For complete hardness testing
(clause 4.2)(Construction and Workmanship)	-	-	-
(clause 4.4)(Tensile Strength and Elongation at Break)	-	-	-
(clause 4.5)(Accelerated Ageing)	-	-	-
(clause 4.6)(Compression Set)	-	-	-
(clause 4.7)(Resistance to Bending)	-	-	-
(clause 4.8)(Adhesion)	-	-	-
(clause 4.9)(Hardness)	-	-	-

-
Included w.e.f.11.08.2025

194

IS 12109 (1987)

General requirements for light duty sewing machine heads for industrial use

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.1(Construction and Function)	-	1000	For Cl. 2, 3 and 4
2.3(Construction and Function)	-	999.97	For Cl. 2, 3 and 4
2.4(Construction and Function)	-	1000	For Cl. 2, 3 and 4
2.5(Construction and Function)	-	1000	For Cl. 2, 3 and 4
2.6(Construction and Function)	-	1000	For Cl. 2, 3 and 4
2.7(Construction and Function)	-	1000	For Cl. 2, 3 and 4
3.1(Finish)	-	1000	For Cl. 2, 3 and 4
3.2(Finish)	-	1000	For Cl. 2, 3 and 4
4.1(Sewing Mechanism)	-	1000	For Cl. 2, 3 and 4
4.2(Sewing Mechanism)	-	1000	For Cl. 2, 3 and 4
4.3(Sewing Mechanism)	-	1000	For Cl. 2, 3 and 4
4.4(Sewing Mechanism)	-	1000	For Cl. 2, 3 and 4
5(Lubrication)	-	1000	For Cl.5
6.1(Accuracy Requirement)	-	4500	For Cl. 6
6.2 Table 1(Accuracy Requirement Needle Bar - Measuring Condition - Needle bar at lowermost position)	-	4500	For Cl. 6
6.2 Table 1(Accuracy Requirement Needle Bar - Measuring Condition - Needle bar at lowermost position)	-	45000	For Cl. 6
6.2 Table 1(Accuracy Requirement Thread takeup lever - Measuring Condition - Thread take up lever at top and intermediate position of motion)	-	4500	For Cl. 6
6.2 Table 1(Accuracy Requirement Thread takeup lever - Measuring Condition - Thread take up lever at top and intermediate position of motion)	-	4500	For Cl. 6
6.2 Table 1(Accuracy Requirement Rotating hook- Measuring Condition - With bobbin-case removed, play of rotating hook bobbin case holder )	-	4500	For Cl. 6
6.2 Table 1(Accuracy Requirement Rotating hook- Measuring Condition - With bobbin-case removed, play of rotating hook bobbin case holder )	-	4500	For Cl. 6
6.2 Table 1(Accuracy Requirement Feed machanlsm- Measuring Condition - Feed dog at the highest position above the needle plate )	-	4500	For Cl. 6
6.2 Table 1(Accuracy Requirement Arm shaft - Measuring Condition - Shaft end )	-	4500	For Cl. 6
6.2 Table 1(Accuracy Requirement Rotating hook shaft- Measuring Condition - Shaft end )	-	4500	For Cl. 6
7 Table 1(Durability Requirements Needle Bar - Measuring Condition - Needle bar at lowermost position)	-	1500	For Cl. 7
7 Table 1(Durability Requirements Needle Bar - Measuring Condition - Needle bar at lowermost position)	-	1500	For Cl. 7
7 Table 1(Durability Requirements Thread takeup lever - Measuring Condition - Thread take up lever at top and intermediate position of motion)	-	1500	For Cl. 7
7 Table 1(Durability Requirements Thread takeup lever - Measuring Condition - Thread take up lever at top and intermediate position of motion)	-	1500	For Cl. 7
7 Table 1(Durability Requirements Rotating hook- Measuring Condition - With bobbin-case removed, play of rotating hook bobbin case holder )	-	1500	For Cl. 7
7 Table 1(Durability Requirements Rotating hook- Measuring Condition - With bobbin-case removed, play of rotating hook bobbin case holder )	-	1500	For Cl. 7
7 Table 1(Durability Requirements Feed machanlsm- Measuring Condition - Feed dog at the highest position above the needle plate )	-	1500	For Cl. 7
7 Table 1(Durability Requirements Arm shaft - Measuring Condition - Shaft end )	-	1500	For Cl. 7
7 Table 1(Durability Requirements Rotating hook shaft- Measuring Condition - Shaft end )	-	1500	For Cl. 7
8 Table 2(Sewing Requirement)	-	1000	For Cl. 8 and 10
8 Table 3(Sewing Requirement)	-	1000	For Cl. 8 and 10
8 Table 2(Sewing Requirement)	-	1000	For Cl. 8 and 10
8 Table 2(Sewing Requirement)	-	1000	For Cl. 8 and 10
8 Table 2(Sewing Requirement)	-	1000	For Cl. 8 and 10
10(Marking)	-	1000	For Cl. 8 and 10
10(Marking)	-	1000	For Cl. 8 and 10
2.1(Construction and Function)	-	0	-
2.3(Construction and Function)	-	0	-
2.4(Construction and Function)	-	0	-
2.5(Construction and Function)	-	0	-
2.6(Construction and Function)	-	0	-
2.7(Construction and Function)	-	0	-
3.1(Finish)	-	0	-
3.2(Finish)	-	0	-
4.1(Sewing Mechanism)	-	0	-
4.2(Sewing Mechanism)	-	0	-
4.3(Sewing Mechanism)	-	0	-
4.4(Sewing Mechanism)	-	0	-
5(Lubrication)	-	0	-
6.1(Accuracy Requirement)	-	0	-
6.2 Table 1(Accuracy Requirement Needle Bar - Measuring Condition - Needle bar at lowermost position)	-	0	-
6.2 Table 1(Accuracy Requirement Needle Bar - Measuring Condition - Needle bar at lowermost position)	-	0	-
6.2 Table 1(Accuracy Requirement Thread takeup lever - Measuring Condition - Thread take up lever at top and intermediate position of motion)	-	0	-
6.2 Table 1(Accuracy Requirement Thread takeup lever - Measuring Condition - Thread take up lever at top and intermediate position of motion)	-	0	-
6.2 Table 1(Accuracy Requirement Rotating hook- Measuring Condition - With bobbin-case removed, play of rotating hook bobbin case holder )	-	0	-
6.2 Table 1(Accuracy Requirement Rotating hook- Measuring Condition - With bobbin-case removed, play of rotating hook bobbin case holder )	-	0	-
6.2 Table 1(Accuracy Requirement Feed machanlsm- Measuring Condition - Feed dog at the highest position above the needle plate )	-	0	-
6.2 Table 1(Accuracy Requirement Arm shaft - Measuring Condition - Shaft end )	-	0	-
6.2 Table 1(Accuracy Requirement Rotating hook shaft- Measuring Condition - Shaft end )	-	0	-
7 Table 1(Durability Requirements Needle Bar - Measuring Condition - Needle bar at lowermost position)	-	0	-
7 Table 1(Durability Requirements Needle Bar - Measuring Condition - Needle bar at lowermost position)	-	0	-
7 Table 1(Durability Requirements Thread takeup lever - Measuring Condition - Thread take up lever at top and intermediate position of motion)	-	0	-
7 Table 1(Durability Requirements Thread takeup lever - Measuring Condition - Thread take up lever at top and intermediate position of motion)	-	0	-
7 Table 1(Durability Requirements Rotating hook- Measuring Condition - With bobbin-case removed, play of rotating hook bobbin case holder )	-	0	-
7 Table 1(Durability Requirements Rotating hook- Measuring Condition - With bobbin-case removed, play of rotating hook bobbin case holder )	-	0	-
7 Table 1(Durability Requirements Feed machanlsm- Measuring Condition - Feed dog at the highest position above the needle plate )	-	0	-
7 Table 1(Durability Requirements Arm shaft - Measuring Condition - Shaft end )	-	0	-
7 Table 1(Durability Requirements Rotating hook shaft- Measuring Condition - Shaft end )	-	0	-
8 Table 2(Sewing Requirement)	-	0	-
8 Table 3(Sewing Requirement)	-	0	-
8 Table 2(Sewing Requirement)	-	0	-
8 Table 2(Sewing Requirement)	-	0	-
8 Table 2(Sewing Requirement)	-	0	-
10(Marking)	-	0	-
10(Marking)	-	0	-
As per Clause 9(Accessories)	-	0	-
As per Clause 11(Packing)	-	0	-
Clause 12(Sampling)	-	0	-
Clause 2.2(Construction and function - Component)	-	0	-
2.1(Construction and Function)	-	0	-
2.3(Construction and Function)	-	0	-
2.4(Construction and Function)	-	0	-
2.5(Construction and Function)	-	0	-
2.6(Construction and Function)	-	0	-
2.7(Construction and Function)	-	0	-
3.1(Finish)	-	0	-
3.2(Finish)	-	0	-
4.1(Sewing Mechanism)	-	0	-
4.2(Sewing Mechanism)	-	0	-
4.3(Sewing Mechanism)	-	0	-
4.4(Sewing Mechanism)	-	0	-
5(Lubrication)	-	0	-
6.1(Accuracy Requirement)	-	0	-
6.2 Table 1(Accuracy Requirement Needle Bar - Measuring Condition - Needle bar at lowermost position)	-	0	-
6.2 Table 1(Accuracy Requirement Needle Bar - Measuring Condition - Needle bar at lowermost position)	-	0	-
6.2 Table 1(Accuracy Requirement Thread takeup lever - Measuring Condition - Thread take up lever at top and intermediate position of motion)	-	0	-
6.2 Table 1(Accuracy Requirement Thread takeup lever - Measuring Condition - Thread take up lever at top and intermediate position of motion)	-	0	-
6.2 Table 1(Accuracy Requirement Rotating hook- Measuring Condition - With bobbin-case removed, play of rotating hook bobbin case holder )	-	0	-
6.2 Table 1(Accuracy Requirement Rotating hook- Measuring Condition - With bobbin-case removed, play of rotating hook bobbin case holder )	-	0	-
6.2 Table 1(Accuracy Requirement Feed machanlsm- Measuring Condition - Feed dog at the highest position above the needle plate )	-	0	-
6.2 Table 1(Accuracy Requirement Arm shaft - Measuring Condition - Shaft end )	-	0	-
6.2 Table 1(Accuracy Requirement Rotating hook shaft- Measuring Condition - Shaft end )	-	0	-
7 Table 1(Durability Requirements Needle Bar - Measuring Condition - Needle bar at lowermost position)	-	0	-
7 Table 1(Durability Requirements Needle Bar - Measuring Condition - Needle bar at lowermost position)	-	0	-
7 Table 1(Durability Requirements Thread takeup lever - Measuring Condition - Thread take up lever at top and intermediate position of motion)	-	0	-
7 Table 1(Durability Requirements Thread takeup lever - Measuring Condition - Thread take up lever at top and intermediate position of motion)	-	0	-
7 Table 1(Durability Requirements Rotating hook- Measuring Condition - With bobbin-case removed, play of rotating hook bobbin case holder )	-	0	-
7 Table 1(Durability Requirements Rotating hook- Measuring Condition - With bobbin-case removed, play of rotating hook bobbin case holder )	-	0	-
7 Table 1(Durability Requirements Feed machanlsm- Measuring Condition - Feed dog at the highest position above the needle plate )	-	0	-
7 Table 1(Durability Requirements Arm shaft - Measuring Condition - Shaft end )	-	0	-
7 Table 1(Durability Requirements Rotating hook shaft- Measuring Condition - Shaft end )	-	0	-
8 Table 2(Sewing Requirement)	-	0	-
8 Table 3(Sewing Requirement)	-	0	-
8 Table 2(Sewing Requirement)	-	0	-
8 Table 2(Sewing Requirement)	-	0	-
8 Table 2(Sewing Requirement)	-	0	-
10(Marking)	-	0	-
10(Marking)	-	0	-
As per Clause 9(Accessories)	-	0	-
As per Clause 11(Packing)	-	0	-
Clause 12(Sampling)	-	0	-
Clause 2.2(Construction and function - Component)	-	0	-
2.1(Construction and Function)	-	-	-
2.3(Construction and Function)	-	-	-
2.4(Construction and Function)	-	-	-
2.5(Construction and Function)	-	-	-
2.6(Construction and Function)	-	-	-
2.7(Construction and Function)	-	-	-
3.1(Finish)	-	-	-
3.2(Finish)	-	-	-
4.1(Sewing Mechanism)	-	-	-
4.2(Sewing Mechanism)	-	-	-
4.3(Sewing Mechanism)	-	-	-
4.4(Sewing Mechanism)	-	-	-
5(Lubrication)	-	-	-
6.1(Accuracy Requirement)	-	-	-
6.2 Table 1(Accuracy Requirement Needle Bar - Measuring Condition - Needle bar at lowermost position)	-	-	-
6.2 Table 1(Accuracy Requirement Needle Bar - Measuring Condition - Needle bar at lowermost position)	-	-	-
6.2 Table 1(Accuracy Requirement Thread takeup lever - Measuring Condition - Thread take up lever at top and intermediate position of motion)	-	-	-
6.2 Table 1(Accuracy Requirement Thread takeup lever - Measuring Condition - Thread take up lever at top and intermediate position of motion)	-	-	-
6.2 Table 1(Accuracy Requirement Rotating hook- Measuring Condition - With bobbin-case removed, play of rotating hook bobbin case holder )	-	-	-
6.2 Table 1(Accuracy Requirement Rotating hook- Measuring Condition - With bobbin-case removed, play of rotating hook bobbin case holder )	-	-	-
6.2 Table 1(Accuracy Requirement Feed machanlsm- Measuring Condition - Feed dog at the highest position above the needle plate )	-	-	-
6.2 Table 1(Accuracy Requirement Arm shaft - Measuring Condition - Shaft end )	-	-	-
6.2 Table 1(Accuracy Requirement Rotating hook shaft- Measuring Condition - Shaft end )	-	-	-
7 Table 1(Durability Requirements Needle Bar - Measuring Condition - Needle bar at lowermost position)	-	-	-
7 Table 1(Durability Requirements Needle Bar - Measuring Condition - Needle bar at lowermost position)	-	-	-
7 Table 1(Durability Requirements Thread takeup lever - Measuring Condition - Thread take up lever at top and intermediate position of motion)	-	-	-
7 Table 1(Durability Requirements Thread takeup lever - Measuring Condition - Thread take up lever at top and intermediate position of motion)	-	-	-
7 Table 1(Durability Requirements Rotating hook- Measuring Condition - With bobbin-case removed, play of rotating hook bobbin case holder )	-	-	-
7 Table 1(Durability Requirements Rotating hook- Measuring Condition - With bobbin-case removed, play of rotating hook bobbin case holder )	-	-	-
7 Table 1(Durability Requirements Feed machanlsm- Measuring Condition - Feed dog at the highest position above the needle plate )	-	-	-
7 Table 1(Durability Requirements Arm shaft - Measuring Condition - Shaft end )	-	-	-
7 Table 1(Durability Requirements Rotating hook shaft- Measuring Condition - Shaft end )	-	-	-
8 Table 2(Sewing Requirement)	-	-	-
8 Table 3(Sewing Requirement)	-	-	-
8 Table 2(Sewing Requirement)	-	-	-
8 Table 2(Sewing Requirement)	-	-	-
8 Table 2(Sewing Requirement)	-	-	-
10(Marking)	-	-	-
10(Marking)	-	-	-
As per Clause 9(Accessories)	-	-	-
As per Clause 11(Packing)	-	-	-
Clause 12(Sampling)	-	-	-
Clause 2.2(Construction and function - Component)	-	-	-

-
Included w.e.f 24.06.2025

195

IS 1610 (2018)

Household sewing machines - General requirements (Fourth Revision)

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Driving arrangement Hand Operated Sewing Machine)	-	2500	For complete Cl. 3, 5, 6 and 7
4.1(Sewing Mechanism Design )	-	2000	For complete Cl. 4, 8 and 12
4.2(Sewing Mechanism Reverse stitch mechanism )	-	2000	For complete Cl. 4, 8 and 12
4.2.1(Sewing Mechanism Stitch Regulator)	-	2000	For complete Cl. 4, 8 and 12
4.3(Sewing Mechanism Thread Tension)	-	2000	For complete Cl. 4, 8 and 12
4.4(Sewing Mechanism Timing)	-	2000	For complete Cl. 4 and 8
4.7(Sewing Mechanism Thread Spool Pin)	-	2000	For complete Cl. 4, 8 and 12
6(Lubrication)	-	1999.99	For complete Cl. 4, 8 and 12
8(WORKMANSHIP AND FINISH)	-	2000	For complete Cl. 4, 8 and 12
8(WORKMANSHIP AND FINISH)	-	2000	For complete Cl. 4, 8 and 12
8(WORKMANSHIP AND FINISH)	-	2000	For complete Cl. 4, 8 and 12
10.1 IS 7491 (Accuracy Requirement Functional Dimension Feed Dog Measuring Condition - Feed dog raised to its highest position )	-	4500	For complete Cl. 10.1, 10.2 and 10.3
10.1 IS 7491 (Accuracy Requirement Functional Dimension Shuttle and shuttle driver Measuring Condition - Shuttle heel at bottom - most position)	-	4500	For complete Cl. 10.1, 10.2 and 10.3
10.1 IS 7491 (Accuracy Requirement Functional Dimension Presser foot Measuring Condition - Presser foot in lifted condition)	-	4500	For complete Cl. 10.1, 10.2 and 10.3
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Needle bar Measuring Condition - Needle bar at lower-most condition)	-	4500	For complete Cl. 10.1, 10.2 and 10.3
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Needle bar Measuring Condition - Needle bar at lower-most condition)	-	4500	For complete Cl. 10.1, 10.2 and 10.3
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Thread take up lever Measuring Condition - Thread take up lever at top and intermediate position)	-	4500	For complete Cl. 10.1, 10.2 and 10.3
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Thread take up lever Measuring Condition - Thread take up lever at top and intermediate position)	-	4500	For complete Cl. 10.1, 10.2 and 10.3
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Shuttle Measuring Condition - Tip of pin at top most bottom most position of needle bar)	-	4500	For complete Cl. 10.1, 10.2 and 10.3
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Shuttle Measuring Condition - Difference between highest & lowest position of needle bar.)	-	4500	For complete Cl. 10.1, 10.2 and 10.3
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Arm shaft Measuring Condition -At different fly wheel position (turn fly wheel by hand) axial push./pull to be given)	-	4500	For complete Cl. 10.1, 10.2 and 10.3
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Flywheel Measuring Condition - Rotate flywheel to Radially measure eccentrity)	-	4500	For complete Cl. 10.1, 10.2 and 10.3
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Feed section Measuring Condition - At its highest position above needle place)	-	4500	For complete Cl. 10.1, 10.2 and 10.3
10.2 IS 7492 (Sewing Requirement)	-	4500	For complete Cl. 10.1, 10.2 and 10.3
10.2 IS 7492 (Sewing Requirement)	-	4500	For complete Cl. 10.1, 10.2 and 10.3
10.2 IS 7492 (Sewing Requirement)	-	4500	For complete Cl. 10.1, 10.2 and 10.3
10.2 IS 7492 (Sewing Requirement)	-	4500	For complete Cl. 10.1, 10.2 and 10.3
10.2 IS 7492 (Sewing Requirement)	-	4500	For complete Cl. 10.1, 10.2 and 10.3
10.3 IS 7493 (Durability Requirement Needle bar Measuring Condition - Needle bar at lower-most condition)	-	4500	For complete Cl. 10.1, 10.2 and 10.3
10.3 IS 7493 (Durability Requirement Needle bar Measuring Condition - Needle bar at lower-most condition)	-	4500	For complete Cl. 10.1, 10.2 and 10.3
10.3 IS 7493 (Durability Requirement Thread take up lever Measuring Condition - Thread take up lever at top and intermediate position)	-	4500	For complete Cl. 10.1, 10.2 and 10.3
10.3 IS 7493 (Durability Requirement Thread take up lever Measuring Condition - Thread take up lever at top and intermediate position)	-	4500	For complete Cl. 10.1, 10.2 and 10.3
10.3 IS 7493 (Durability Requirement Shuttle Measuring Condition - Tip of pin at top most bottom most position of needle bar)	-	4500	For complete Cl. 10.1, 10.2 and 10.3
10.3 IS 7493 (Accuracy Requirement Assembly Clearance Shuttle Measuring Condition - Difference between two indicator readings when needle bar is at its highest and lowest position)	-	4500	For complete Cl. 10.1, 10.2 and 10.3
10.3 IS 7493 (Durability requirement Arm shaft Measuring Condition -At different fly wheel position (turn fly wheel by hand) axial push./pull to be given)	-	4500	For complete Cl. 10.1, 10.2 and 10.3
10.3 IS 7493 (Durability Requirement Feed section Measuring Condition - At its highest position above needle place)	-	4500	For complete Cl. 10.1, 10.2 and 10.3
12(Marking)	-	2000	For complete Cl. 4, 8 and 12
12(Marking)	-	2000	For complete Cl. 4, 8 and 12
3.1(Driving arrangement Hand Operated Sewing Machine)	-	0	-
4.1(Sewing Mechanism Design )	-	0	-
4.2(Sewing Mechanism Reverse stitch mechanism )	-	0	-
4.2.1(Sewing Mechanism Stitch Regulator)	-	0	-
4.3(Sewing Mechanism Thread Tension)	-	0	-
4.4(Sewing Mechanism Timing)	-	0	-
4.7(Sewing Mechanism Thread Spool Pin)	-	0	-
6(Lubrication)	-	0	-
8(WORKMANSHIP AND FINISH)	-	0	-
8(WORKMANSHIP AND FINISH)	-	0	-
8(WORKMANSHIP AND FINISH)	-	0	-
10.1 IS 7491 (Accuracy Requirement Functional Dimension Feed Dog Measuring Condition - Feed dog raised to its highest position )	-	0	-
10.1 IS 7491 (Accuracy Requirement Functional Dimension Shuttle and shuttle driver Measuring Condition - Shuttle heel at bottom - most position)	-	0	-
10.1 IS 7491 (Accuracy Requirement Functional Dimension Presser foot Measuring Condition - Presser foot in lifted condition)	-	0	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Needle bar Measuring Condition - Needle bar at lower-most condition)	-	0	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Needle bar Measuring Condition - Needle bar at lower-most condition)	-	0	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Thread take up lever Measuring Condition - Thread take up lever at top and intermediate position)	-	0	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Thread take up lever Measuring Condition - Thread take up lever at top and intermediate position)	-	0	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Shuttle Measuring Condition - Tip of pin at top most bottom most position of needle bar)	-	0	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Shuttle Measuring Condition - Difference between highest & lowest position of needle bar.)	-	0	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Arm shaft Measuring Condition -At different fly wheel position (turn fly wheel by hand) axial push./pull to be given)	-	0	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Flywheel Measuring Condition - Rotate flywheel to Radially measure eccentrity)	-	0	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Feed section Measuring Condition - At its highest position above needle place)	-	0	-
10.2 IS 7492 (Sewing Requirement)	-	0	-
10.2 IS 7492 (Sewing Requirement)	-	0	-
10.2 IS 7492 (Sewing Requirement)	-	0	-
10.2 IS 7492 (Sewing Requirement)	-	0	-
10.2 IS 7492 (Sewing Requirement)	-	0	-
10.3 IS 7493 (Durability Requirement Needle bar Measuring Condition - Needle bar at lower-most condition)	-	0	-
10.3 IS 7493 (Durability Requirement Needle bar Measuring Condition - Needle bar at lower-most condition)	-	0	-
10.3 IS 7493 (Durability Requirement Thread take up lever Measuring Condition - Thread take up lever at top and intermediate position)	-	0	-
10.3 IS 7493 (Durability Requirement Thread take up lever Measuring Condition - Thread take up lever at top and intermediate position)	-	0	-
10.3 IS 7493 (Durability Requirement Shuttle Measuring Condition - Tip of pin at top most bottom most position of needle bar)	-	0	-
10.3 IS 7493 (Accuracy Requirement Assembly Clearance Shuttle Measuring Condition - Difference between two indicator readings when needle bar is at its highest and lowest position)	-	0	-
10.3 IS 7493 (Durability requirement Arm shaft Measuring Condition -At different fly wheel position (turn fly wheel by hand) axial push./pull to be given)	-	0	-
10.3 IS 7493 (Durability Requirement Feed section Measuring Condition - At its highest position above needle place)	-	0	-
12(Marking)	-	0	-
12(Marking)	-	0	-

-
Included w.e.f 24.06.2025

196

IS 13164 (1991)

Ferrosilicomagnesium - Specification

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause-3.2.1(Tapped Lot Method)	-	12500	For complete testing
Clause-3.2.2(Graded Lot Method)	-	12500	For complete testing
Clause-3.2.3(Blended Lot Method)	-	12500	For complete testing
Clause-3.3(Definition)	-	12500	For complete testing
Clause-4(Grades)	-	12500	For complete testing
Clause-6(Supply of Material)	-	12500	For complete testing
Clause-7.1(Constitution of Consignment)	-	12500	For complete testing
Clause-7.2.1, Table-1(Si)	-	12500	For complete testing
Clause-7.2.1, Table-1(Mg)	-	12500	For complete testing
Clause-7.2.1, Table-1(Al, Max)	-	12500	For complete testing
Clause-7.2.1, Table-1(Ca, Max)	-	12500	For complete testing
Clause-8.1(Size Range)	-	12500	For complete testing
Clause-12(Marking)	-	12500	For complete testing

-
Included w.e.f.10.07.2025

197

IS 1466 (1985)

Specification for ferrovanadium (Third Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause-2.1(Ferro Vanadium)	-	15000	For complete testing
Clause-3(Grades)	-	15000	For complete testing
Clause-4(Supply of Material)	-	15000	For complete testing
Clause-5(Chemical Composition)	-	15000	For complete testing
Clause-6(Norminal size Ranges)	-	15000	For complete testing
Clause-9(Marking)	-	15000	For complete testing
3 & 5(V)	-	15000	For complete testing
3 & 5(Si)	-	15000	For complete testing
3 & 5(C)	-	15000	For complete testing
3 & 5(S)	-	15000	For complete testing
3 & 5(P)	-	15000	For complete testing
3 & 5(Al)	-	15000	For complete testing
3 & 5(Mn)	-	15000	For complete testing
3 & 5(Cr)	-	15000	For complete testing
3 & 5(Cu)	-	15000	For complete testing
3 & 5(Ni)	-	15000	For complete testing
3 & 5(Pb)	-	15000	For complete testing
3 & 5(Sn)	-	15000	For complete testing
3 & 5(Zn)	-	15000	For complete testing
3 & 5(Mo)	-	15000	For complete testing
3 & 5(Ti)	-	15000	For complete testing
Clause-2.1(Ferro Vanadium)	-	-	-
Clause-3(Grades)	-	-	-
Clause-4(Supply of Material)	-	-	-
Clause-5(Chemical Composition)	-	-	-
Clause-6(Norminal size Ranges)	-	-	-
Clause-9(Marking)	-	-	-
3 & 5(V)	-	-	-
3 & 5(Si)	-	-	-
3 & 5(C)	-	-	-
3 & 5(S)	-	-	-
3 & 5(P)	-	-	-
3 & 5(Al)	-	-	-
3 & 5(Mn)	-	-	-
3 & 5(Cr)	-	-	-
3 & 5(Cu)	-	-	-
3 & 5(Ni)	-	-	-
3 & 5(Pb)	-	-	-
3 & 5(Sn)	-	-	-
3 & 5(Zn)	-	-	-
3 & 5(Mo)	-	-	-
3 & 5(Ti)	-	-	-

-
Included w.e.f.10.07.2025

198

IS 1170 (1992)

Ferrochromium - Specification (Second Revision)

15800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.2 ; 8.2.1 ; 8.2.2 ; 8.3 ; 8.4 ; Table 1(Chemical Composition ; IS 1559 or any other established instrumental/chemical method ; latest version of IS 1559 shall be the referee method )	-	15800	For complete testing
8.5(Residual elements)	-	15800	For complete testing
9.5(Manganese)	-	15800	For complete testing
10.5(Nickle)	-	15800	For complete testing
11.5(Vanadium)	-	15800	For complete testing
12.5(Copper)	-	15800	For complete testing
13.5(Molybdenum)	-	15800	For complete testing
14.5(Columbium)	-	15800	For complete testing
15.5(Tantalum)	-	15800	For complete testing
16.5(Cobalt)	-	15800	For complete testing
17.5(Aluminium)	-	15800	For complete testing
18.5(Titanium)	-	15800	For complete testing
19.5(Zirconium)	-	15800	For complete testing
20.5(Arsenic)	-	15800	For complete testing
21.5(Lead)	-	15800	For complete testing
22.5(Tin)	-	15800	For complete testing
23.5(Zinc)	-	15800	For complete testing
24.5(Boron)	-	15800	For complete testing
25.5(Antimony)	-	15800	For complete testing
26.5(Silver)	-	15800	For complete testing
27.5(Bismuth)	-	15800	For complete testing
9 , Table 2(Size Range)	-	15800	For complete testing
10(Extraneous contamination)	-	15800	For complete testing
8.2 ; 8.2.1 ; 8.2.2 ; 8.3 ; 8.4 ; Table 1(Chemical Composition ; IS 1559 or any other established instrumental/chemical method ; latest version of IS 1559 shall be the referee method )	-	15800	For complete testing
8.5(Residual elements)	-	15800	For complete testing
9.5(Manganese)	-	15800	For complete testing
10.5(Nickle)	-	15800	For complete testing
11.5(Vanadium)	-	15800	For complete testing
12.5(Copper)	-	15800	For complete testing
13.5(Molybdenum)	-	15800	For complete testing
14.5(Columbium)	-	15800	For complete testing
15.5(Tantalum)	-	15800	For complete testing
16.5(Cobalt)	-	15800	For complete testing
17.5(Aluminium)	-	15800	For complete testing
18.5(Titanium)	-	15800	For complete testing
19.5(Zirconium)	-	15800	For complete testing
20.5(Arsenic)	-	15800	For complete testing
21.5(Lead)	-	15800	For complete testing
22.5(Tin)	-	15800	For complete testing
23.5(Zinc)	-	15800	For complete testing
24.5(Boron)	-	15800	For complete testing
25.5(Antimony)	-	15800	For complete testing
26.5(Silver)	-	15800	For complete testing
27.5(Bismuth)	-	15800	For complete testing
9 , Table 2(Size Range)	-	15800	For complete testing
10(Extraneous contamination)	-	15800	For complete testing
Table 1 (Cl 5 and 8.2.1)(Chromium)	-	15800	For complete testing
Table 1 (Cl 5 and 8.2.1)(Copper)	-	15800	For complete testing
Table 1 (Cl 5 and 8.2.1)(Si)	-	15800	For complete testing
Table 1 (Cl 5 and 8.2.1)(Nitrogen)	-	15800	For complete testing
Table 1 (Cl 5 and 8.2.1)(Sulphur)	-	15800	For complete testing
Table 1 (Cl 5 and 8.2.1)(Aluminium)	-	15800	For complete testing
Table 1 (Cl 5 and 8.2.1)(Phosphorus)	-	15800	For complete testing

-
Included w.e.f.10.07.2025

199

IS 1110 (2023)

FERROSILICON -- SPECIFICATIONS

14800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1(Constitution of Consignment)	-	14800	For complete testing
Clauses 4 and 7.2.1-Table 1(Silicon)	-	14800	For complete testing
Clauses 4 and 7.2.1-Table 1(Carbon)	-	14800	For complete testing
Clauses 4 and 7.2.1-Table 1(Sulphur)	-	14800	For complete testing
Clauses 4 and 7.2.1-Table 1(Phosphorus)	-	14800	For complete testing
Clauses 4 and 7.2.1-Table 1(Aluminium)	-	14800	For complete testing
Clauses 4 and 7.2.1-Table 1(Calcium)	-	14800	For complete testing
Clauses 4 and 7.2.1-Table 1(Manganese)	-	14800	For complete testing
Clauses 4 and 7.2.1-Table 1(Manganese)	-	14800	For complete testing
Clauses 4 and 7.2.1-Table 1(Manganese)	-	14800	For complete testing
Clauses 4 and 7.2.1-Table 1(Boron)	-	14800	For complete testing
Clauses 4 and 7.2.1-Table 1(Zirconium)	-	14800	For complete testing
Clauses 4 and 7.2.1-Table 1(Titanium)	-	14800	For complete testing
8(SIZE)	-	14800	For complete testing
9(Extraneous contamination)	-	14800	For complete testing
7.1(Constitution of Consignment)	-	-	-
Clauses 4 and 7.2.1-Table 1(Silicon)	-	-	-
Clauses 4 and 7.2.1-Table 1(Carbon)	-	-	-
Clauses 4 and 7.2.1-Table 1(Sulphur)	-	-	-
Clauses 4 and 7.2.1-Table 1(Phosphorus)	-	-	-
Clauses 4 and 7.2.1-Table 1(Aluminium)	-	-	-
Clauses 4 and 7.2.1-Table 1(Calcium)	-	-	-
Clauses 4 and 7.2.1-Table 1(Manganese)	-	-	-
Clauses 4 and 7.2.1-Table 1(Manganese)	-	-	-
Clauses 4 and 7.2.1-Table 1(Manganese)	-	-	-
Clauses 4 and 7.2.1-Table 1(Boron)	-	-	-
Clauses 4 and 7.2.1-Table 1(Zirconium)	-	-	-
Clauses 4 and 7.2.1-Table 1(Titanium)	-	-	-
8(SIZE)	-	-	-
9(Extraneous contamination)	-	-	-

-
Included w.e.f.10.07.2025

200

IS 7902 (2001)

Aluminium alloy forging stock and forgings (Alloy 24345) for aerospace applications - Specification (First Revision)

19800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(MANUFACTURE)	-	1800	For complete dimensional and other qualitative test
6(FREEDOM FROM DEFECTS)	-	1800	For complete dimensional and other qualitative test
7 table 1(CHEMICAL COMPOSITION)	-	6500	For complete chemical testing
8.1(Forging Stocks)	-	1800	For complete dimensional and other qualitative test
8.2(Forgings)	-	1800	For complete dimensional and other qualitative test
9(HEAT TREATMENT)	-	1800	For complete dimensional and other qualitative test
10.1(Tensile Test)	-	6500	For complete mechanical testing
10.2(Hardness)	-	6500	For complete mechanical testing
11(DIMENSIONS AND TOLERANCES)	-	1800	For complete dimensional and other qualitative test
12.1(Inspection and Testing)	-	1800	For complete dimensional and other qualitative test
12.2.1(Ultrasonic test)	-	2500	For ultrasonic and dye penetrant test
12.2.1(Dye Penetrant Test)	-	2500	For ultrasonic and dye penetrant test
12.2.2(Macro and Micro-Examination)	-	2500	For macro and micro examination test
13(RETEST)	-	1800	For complete dimensional and other qualitative test
Cl.7(Copper - IS 504 and its parts or any other intrumental/chemical methods)	-	6500	For complete chemical testing
Cl.7(Magnesium - IS 504 and its parts or any other intrumental/chemical methods)	-	6500	For complete chemical testing
Cl.7(Manganese - IS 504 and its parts or any other intrumental/chemical methods)	-	6500	For complete chemical testing
Cl.7(Titanium - IS 504 and its parts or any other intrumental/chemical methods)	-	6500	For complete chemical testing
Cl.7(Titanium+Zirconium - IS 504 and its parts or any other intrumental/chemical methods)	-	6500	For complete chemical testing
Cl.7(Iron - IS 504 and its parts or any other intrumental/chemical methods)	-	6500	For complete chemical testing
Cl.7(Zinc - IS 504 and its parts or any other intrumental/chemical methods)	-	6500	For complete chemical testing
Cl.7(Tin - IS 504 and its parts or any other intrumental/chemical methods)	-	6500	For complete chemical testing
Cl.7(Chromium - IS 504 and its parts or any other intrumental/chemical methods)	-	6500	For complete chemical testing
Cl.7(Nickel - IS 504 and its parts or any other intrumental/chemical methods)	-	6500	For complete chemical testing
Cl.7(Lead - IS 504 and its parts or any other intrumental/chemical methods)	-	6500	For complete chemical testing
Cl.7(Copper - IS 504 and its parts or any other intrumental/chemical methods)	-	6500	For complete chemical testing
Cl.7(Magnesium - IS 504 and its parts or any other intrumental/chemical methods)	-	6500	For complete chemical testing
Cl.7(Silicon - IS 504 and its parts or any other intrumental/chemical methods)	-	6500	For complete chemical testing
Cl.7(Manganese - IS 504 and its parts or any other intrumental/chemical methods)	-	6500	For complete chemical testing
Cl.7(Titanium - IS 504 and its parts or any other intrumental/chemical methods)	-	6500	For complete chemical testing
Cl.7(Titanium+Zirconium - IS 504 and its parts or any other intrumental/chemical methods)	-	6500	For complete chemical testing
Cl.7(Iron - IS 504 and its parts or any other intrumental/chemical methods)	-	6500	For complete chemical testing
Cl.7(Zinc - IS 504 and its parts or any other intrumental/chemical methods)	-	6500	For complete chemical testing
Cl.7(Tin - IS 504 and its parts or any other intrumental/chemical methods)	-	6500	For complete chemical testing
Cl.7(Chromium - IS 504 and its parts or any other intrumental/chemical methods)	-	6500	For complete chemical testing
Cl.7(Nickel - IS 504 and its parts or any other intrumental/chemical methods)	-	6500	For complete chemical testing
Cl.7(Nickel - IS 504 and its parts or any other intrumental/chemical methods)	-	6500	For complete chemical testing
6(Freedom from defect)	-	1800	For complete dimensional and other qualitative test
10.1(Tensile strength)	-	6500	For complete mechanical testing
10.1(0.2 % proof stress)	-	6500	For complete mechanical testing
10.1(Elongation)	-	6500	For complete mechanical testing
10.2(Hardness Test)	-	6500	For complete mechanical testing
11(Dimensions and Tolerance)	-	1800	For complete dimensional and other qualitative test
6(Freedom from defect)	-	1800	For complete dimensional and other qualitative test
10.1(Tensile strength)	-	6500	For complete mechanical testing
10.1(0.2 % proof stress)	-	6500	For complete mechanical testing
10.1(Elongation)	-	6500	For complete mechanical testing
10.2(Hardness Test)	-	6500	For complete mechanical testing
11(DIMENSIONS AND TOLEF&WtCES)	-	1800	For complete dimensional and other qualitative test
5(MANUFACTURE)	-	0	-
6(FREEDOM FROM DEFECTS)	-	0	-
7 table 1(CHEMICAL COMPOSITION)	-	0	-
8.1(Forging Stocks)	-	0	-
8.2(Forgings)	-	0	-
9(HEAT TREATMENT)	-	0	-
10.1(Tensile Test)	-	0	-
10.2(Hardness)	-	0	-
11(DIMENSIONS AND TOLERANCES)	-	0	-
12.1(Inspection and Testing)	-	0	-
12.2.1(Ultrasonic test)	-	0	-
12.2.1(Dye Penetrant Test)	-	0	-
12.2.2(Macro and Micro-Examination)	-	0	-
13(RETEST)	-	0	-
Cl.7(Copper - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Magnesium - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Manganese - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Titanium - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Titanium+Zirconium - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Iron - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Zinc - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Tin - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Chromium - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Nickel - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Lead - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Copper - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Magnesium - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Silicon - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Manganese - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Titanium - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Titanium+Zirconium - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Iron - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Zinc - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Tin - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Chromium - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Nickel - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Nickel - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
6(Freedom from defect)	-	0	-
10.1(Tensile strength)	-	0	-
10.1(0.2 % proof stress)	-	0	-
10.1(Elongation)	-	0	-
10.2(Hardness Test)	-	0	-
11(Dimensions and Tolerance)	-	0	-
6(Freedom from defect)	-	0	-
10.1(Tensile strength)	-	0	-
10.1(0.2 % proof stress)	-	0	-
10.1(Elongation)	-	0	-
10.2(Hardness Test)	-	0	-
11(DIMENSIONS AND TOLEF&WtCES)	-	0	-

-
Included w.e.f 19.06.2025

201

IS 13098 (2024)

AUTOMOTIVE VEHICLES TUBES FOR PNEUMATIC TYRES â SPECIFICATION (second revision)

10500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 3.1(Materials)	-	10500	For complete testing
Cl 3.2(Classification)	-	10500	For complete testing
Cl 3.2.1(Blend Name)	-	10500	For complete testing
Cl 3.3(Fit)	-	10500	For complete testing
Cl 3.3.1(Thickness Uniformity)	-	10500	For complete testing
Cl 4.1.1(Elongation)	-	10500	For complete testing
Cl 4.1.2(Strength of Splice)	-	10500	For complete testing
Cl 4.1.3(Set After Ageing)	-	10500	For complete testing
Cl 4.1.4(Accelerated Ageing)	-	10500	For complete testing
Cl 5(AIR TIGHTNESS)	-	10500	For complete testing
Cl 6(MARKING)	-	10500	For complete testing

-
Included w.e.f 08.05.2025

202

IS 6118 (2017)

Pliers and nippers - Multiple slip joint pliers - Dimensions and test values (Second Revision)

13500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Table 1(l)	-	13500	5000: For Dimensional Tests 5000: For Mechanical Tests 3500: For Chemical Tests
Table 1(t1, max)	-	13500	5000: For Dimensional Tests 5000: For Mechanical Tests 3500: For Chemical Tests
Table 1(g, min)	-	13500	5000: For Dimensional Tests 5000: For Mechanical Tests 3500: For Chemical Tests
Table 1(l3.min)	-	13500	5000: For Dimensional Tests 5000: For Mechanical Tests 3500: For Chemical Tests
Table 1(l1)	-	13500	5000: For Dimensional Tests 5000: For Mechanical Tests 3500: For Chemical Tests
Table 1(Fa)	-	13500	5000: For Dimensional Tests 5000: For Mechanical Tests 3500: For Chemical Tests
Table 1(Sb)	-	13500	5000: For Dimensional Tests 5000: For Mechanical Tests 3500: For Chemical Tests
6(Chemical Composition)	-	13500	5000: For Dimensional Tests 5000: For Mechanical Tests 3500: For Chemical Tests
7(Hardness)	-	0	-
Table 1(l)	-	0	-
Table 1(t1, max)	-	0	-
Table 1(g, min)	-	0	-
Table 1(l3.min)	-	0	-
Table 1(l1)	-	0	-
Table 1(Fa)	-	0	-
Table 1(Sb)	-	0	-
6(Chemical Composition)	-	0	-
7(Hardness)	-	0	-
Table 1(l)	-	0	-
Table 1(t1, max)	-	0	-
Table 1(g, min)	-	0	-
Table 1(l3.min)	-	0	-
Table 1(l1)	-	0	-
Table 1(Fa)	-	0	-
Table 1(Sb)	-	0	-
6(Chemical Composition)	-	0	-
7(Hardness)	-	0	-

-
Included.w.e.f.03.06.2025

203

IS 6149 (1984)

Specification for single - Ended open - Jaw adjustable wrenches (First Revision)

13500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2(Type)	-	13500	For complete testing
3(Grades)	-	13500	For complete testing
4 Table-1(Dimensions- Nominal Size)	-	13500	For complete testing
4 Table-1(Dimensions- l)	-	13500	For complete testing
4 Table-1(Dimensions- s)	-	13500	For complete testing
4 Table-1(Dimensions- a)	-	13500	For complete testing
4 Table-1(Dimensions- b)	-	13500	For complete testing
4 Table-1(Dimensions- t)	-	13500	For complete testing
4 Table-1(Dimensions- d)	-	13500	For complete testing
4 Table-1(Dimensions- Opening of adjustable jaws)	-	13500	For complete testing
6(Hardness- Frame, handle and Jaw)	-	13500	For complete testing
6(Hardness- Worm)	-	13500	For complete testing
6(Hardness- Worm pin)	-	13500	For complete testing
7(Manufacture,Workmanship & Finish)	-	13500	For complete testing
7(Manufacture,Workmanship & Finish)	-	13500	For complete testing
7(Manufacture,Workmanship & Finish)	-	13500	For complete testing
7(Manufacture,Workmanship & Finish)	-	13500	For complete testing
7(Manufacture,Workmanship & Finish)	-	13500	For complete testing
8(Longitudinal Play of Adjustable Jaw)	-	13500	For complete testing
8(Transverse Play of Adjustable Jaw)	-	13500	For complete testing
8(Torque)	-	13500	For complete testing
5(Chemical Composition)	-	13500	For complete testing

-
Included w.e.f.21.05.2025

204

IS 4509 (1992)

Ring slugging wrenches (Spanners) - specification (First Revision)

9500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Dimensions- s)	-	9500	For Complete testing
3(Dimensions- a)	-	9500	For Complete testing
3(Dimensions- b)	-	9500	For Complete testing
3(Dimensions- l)	-	9500	For Complete testing
5(Hardness)	-	9500	For Complete testing
6(Workmanship and Finish)	-	9500	For Complete testing
7(PRESERVATION AND PACKING)	-	9500	For Complete testing
9(Designation)	-	9500	For Complete testing
4(Chemical Test)	-	9500	For Complete testing

-
Included w.e.f.21.05.2025

205

IS 4003 : Part 2 (1986)

Specification for pipe wrenches: Part 2 heavy duty (First Revision)

13500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Dimensions- Nominal Size)	-	13500	For complete testing
3(Dimensions-Capacity D min)	-	13500	For complete testing
3(Dimensions- Capacity D max)	-	13500	For complete testing
3(Dimensions- Jaw Thickness,T min)	-	13500	For complete testing
3(Dimensions- Length of movablejae, l1)	-	13500	For complete testing
3(Dimensions- Length of Handle, l2)	-	13500	For complete testing
3(Dimensions- Width of Nut, N)	-	13500	For complete testing
5(Hardness- Movable and heel Jaws)	-	13500	For complete testing
5(Hardness- Shank of movable Jaw)	-	13500	For complete testing
5(Hardness- Adjustable nut)	-	13500	For complete testing
6.1(Manufacture- Handel)	-	13500	For complete testing
6.1(Manufacture- Handel)	-	13500	For complete testing
6.2(Movable Jaw)	-	13500	For complete testing
6.2(Movable Jaw)	-	13500	For complete testing
6.3(Heel jaw)	-	13500	For complete testing
6.3(Heel jaw)	-	13500	For complete testing
6.4(Adjusting Nut)	-	13500	For complete testing
6.4(Adjusting Nut)	-	13500	For complete testing
6.4(Adjusting Nut)	-	13500	For complete testing
6.5(Springs)	-	13500	For complete testing
6.5(Springs)	-	13500	For complete testing
7(Workmanship & Finish)	-	13500	For complete testing
7(Workmanship & Finish)	-	13500	For complete testing
7(Workmanship & Finish)	-	13500	For complete testing
7(Workmanship & Finish)	-	13500	For complete testing
8(Operation)	-	13500	For complete testing
8(Operation)	-	13500	For complete testing
11.1(Static Load Test)	-	13500	For complete testing
11.1(Static Load Test)	-	13500	For complete testing
4 AND AS PER IS 1570 PART 2(MANGANESE)	-	13500	For complete testing
4 AND AS PER IS 1570 PART 2(PHOSPHORUS)	-	13500	For complete testing
4 AND AS PER IS 1570 PART 2(SULPHUR)	-	13500	For complete testing
4 AND AS PER IS 1570 PART 2(CARBON)	-	13500	For complete testing
4 AND AS PER IS 4454 PART 1(MICRO ALLOY)	-	13500	For complete testing
4 AND AS PER IS 4454 PART 1(NITROGEN)	-	13500	For complete testing
4 AND AS PER IS 4454 PART 1(cu + cr + ni)	-	13500	For complete testing
4 AND AS PER IS 4454 PART 1(SULPHUR+ PHOSPHORUS)	-	13500	For complete testing
4 AND AS PER IS 4454 PART 1(COPPER)	-	13500	For complete testing
4 AND AS PER IS 4454 PART 1(PHOSPHORUS)	-	13500	For complete testing
4 AND AS PER IS 4454 PART 1(SULPHUR)	-	13500	For complete testing
4 AND AS PER IS 4454 PART 1(MANGANESE)	-	13500	For complete testing
4 AND AS PER IS 4454 PART 1(SILICON)	-	13500	For complete testing
4 AND AS PER IS 4454 PART 1(CARBON)	-	13500	For complete testing
4 AND AS PER IS 2707(MICRO ALLOY)	-	13500	For complete testing
4 AND AS PER IS 2707(SILICON)	-	13500	For complete testing
4 AND AS PER IS 2707(MANGANESE)	-	13500	For complete testing
4 AND AS PER IS 2707(PHOSPHORUS)	-	13500	For complete testing
4 AND AS PER IS 2707(SULPHUR)	-	13500	For complete testing
4 AND AS PER IS 2707(CARBON)	-	13500	For complete testing

-
Included w.e.f.21.05.2025

206

IS 4003 : Part 1 (1978)

Specification for pipe wrenches: Part 1 general purpose (First Revision)

13500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. NO.3.1("Quality of Glass Tableware ")	-	13500	For complete Testing
Cl. NO.3.2(Workmanship)	-	13500	For complete Testing
Cl. NO.3.3(Tolerance on Nominal Capacity)	-	13500	For complete Testing
Cl. NO.3.4(Thermal Shock Test)	-	13500	For complete Testing
Cl. NO.3.5(Alkalinity)	-	13500	For complete Testing
Cl. NO.4.("MARKING AND PACKING ")	-	13500	For complete Testing
3(Dimensions- Nominal Size)	-	13500	For complete Testing
3(Dimensions-Minimum capacity)	-	13500	For complete Testing
3(Dimensions-Maximum capacity, D)	-	13500	For complete Testing
3(Dimensions- Jaw Thickness,T min)	-	13500	For complete Testing
3(Dimensions- Length of movablejae, l1)	-	13500	For complete Testing
3(Dimensions- Length of Handle, l2)	-	13500	For complete Testing
3(Dimensions- Width of Nut, N)	-	13500	For complete Testing
5(Hardness- Jaws)	-	13500	For complete Testing
5(Hardness- Handle of movable Jaw)	-	13500	For complete Testing
5(Hardness- Shank of movable Jaw)	-	13500	For complete Testing
6.1(Manufacture- Handel)	-	13500	For complete Testing
6.1(Manufacture- Handel)	-	13500	For complete Testing
6.2(Manufacture- Movable Jaw)	-	13500	For complete Testing
6.2(Manufacture- Movable Jaw)	-	13500	For complete Testing
6.2(Manufacture- Movable Jaw)	-	13500	For complete Testing
6.3(Manufacture- Adjusting Nut)	-	13500	For complete Testing
6.3(Manufacture- Adjusting Nut)	-	13500	For complete Testing
6.4(Manufacture- Frame)	-	13500	For complete Testing
6.5(Manufacture- Hinge Pin)	-	13500	For complete Testing
6.6(Manufacture- Spring)	-	13500	For complete Testing
6.6(Manufacture- Spring)	-	13500	For complete Testing
6.6(Manufacture- Spring)	-	13500	For complete Testing
7(Workmanship & Finish)	-	13500	For complete Testing
7(Workmanship & Finish)	-	13500	For complete Testing
7(Workmanship & Finish)	-	13500	For complete Testing
8(Operation)	-	13500	For complete Testing
8(Operation)	-	13500	For complete Testing
13.1(Static Load Test)	-	13500	For complete Testing
13.1(Static Load Test)	-	13500	For complete Testing
13.2(Static- Shock Load Test)	-	13500	For complete Testing
13.2(Static- Shock Load Test)	-	13500	For complete Testing
4 AND AS PER IS 1570 PART 4(BORON)	-	13500	For complete Testing
4 AND AS PER IS 1570 PART 4(VANADIM)	-	13500	For complete Testing
4 AND AS PER IS 1570 PART 4(ALUMINIUM)	-	13500	For complete Testing
4 AND AS PER IS 1570 PART 4(MOLYBDENUM)	-	13500	For complete Testing
4 AND AS PER IS 1570 PART 4(SILICON)	-	13500	For complete Testing
4 AND AS PER IS 1570 PART 4(MANGANESE)	-	13500	For complete Testing
4 AND AS PER IS 1570 PART 4(CHROMIUM)	-	13500	For complete Testing
4 AND AS PER IS 1570 PART 4(NICKEL)	-	13500	For complete Testing
4 AND AS PER IS 1570 PART 4(CARBON)	-	13500	For complete Testing
4 AND AS PER IS 1570 PART 2(MANGANESE)	-	13500	For complete Testing
4 AND AS PER IS 1570 PART 2(PHOSPHORUS)	-	13500	For complete Testing
4 AND AS PER IS 1570 PART 2(CARBON)	-	13500	For complete Testing
4 AND AS PER IS 1570 PART 2(SULPHUR)	-	13500	For complete Testing

-
Included w.e.f.21.05.2025

207

IS 14650 (2023)

UNALLOYED AND ALLOYED STEEL INGOT AND SEMI-FINISHED PRODUCTS FOR RE-ROLLING PURPOSES - SPECIFICATION (First Revision)

7450 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause - 7.1(CARBON)	-	7450	For complete testing
Clause - 7.1(SULPHUR)	-	7450	For complete testing
Clause - 7.1(PHOSPHURS)	-	7450	For complete testing
Clause - 7.1(MANGANESE)	-	7450	For complete testing
Clause - 7.1(NITROGEN)	-	7450	For complete testing
As per Clause 10(Dimension)	-	7450	For complete testing
As per Clause 10.1(Dimension Width)	-	7450	For complete testing
As per Clause 10.1(Dimension Thickness)	-	7450	For complete testing
As per Clause 10.2(Dimension Length)	-	7450	For complete testing
As per Clause 11/11.1/11.2/11.3/11.4(Tolerances)	-	7450	For complete testing
As per Clause 11.5(Bend)	-	7450	For complete testing
As per Clause 11.6(Camber)	-	7450	For complete testing
As per Clause 11.7 (i)(Out of Square)	-	7450	For complete testing
As per Clause 11.7 (ii)(Round Corners)	-	7450	For complete testing
As per Clause 11.7 (iii)(Ridges due to gas cutting)	-	7450	For complete testing
As per Clause 11.7 (iv)(Taper (Width variation on top and bottom surface at one location)	-	7450	For complete testing
As per Clause 11.7 (v)(Edge slanting (Width variation on top and bottom surface at one location)	-	7450	For complete testing
As per Clause 11.7 (vi)(Convexity(Difference in thickness from edge to curve)	-	7450	For complete testing
As per Clause 11.7 (vii)(Chamfering (Length variation on top and bottom surface at one location)	-	7450	For complete testing
As per Clause 11.7 (viii)(Wedge (Thickness variation at the edges along the cross section)	-	7450	For complete testing
As per Clause 11.7 (ix)(Scarfing pits)	-	7450	For complete testing
As per Clause 12/12.1/12.2/12.3(Freedom from defects)	-	7450	For complete testing
Clause. 13(Macro examination test.)	-	7450	For complete testing
Clause. 13(Macro examination test.)	-	7450	For complete testing
Clause. 13(Sulphur print.)	-	7450	For complete testing
Clause. 13(Inclusion content)	-	7450	For complete testing
Clause. 14(Marking)	-	7450	For complete testing
Clause.15(Ordering information)	-	7450	For complete testing
Clause.6.0(Manufacture)	-	7450	For complete testing
Clause.7.1(Silicon)	-	7450	For complete testing
Clause.7.1(Carbon Equbalant)	-	7450	For complete testing
Clause.7.1(Microalloy element)	-	7450	For complete testing

-
Included w.e.f.26.05.2025

208

IS 15509 (2017)

Double - Pitch precision roller chains - Attachments and associated chain sprockets for transmission and conveyors (First Revision)

22500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Transmission chains)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
3.2(Designation)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
3.3(Dimensions)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
3.4.1(General)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
3.4.2(Testing)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
3.5(Preloading)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
3.6(Length validation)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
3.7(Marking)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
4.1(General)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
4.2(Nomenclature)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
4.3(Designation)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
4.4(Dimensions)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
4.5(Length validation)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
4.6(Marking)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
4.7.1(General)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
4.7.2(Nomenclature)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
4.7.3(Designation)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
4.7.4(Dimensions)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
4.7.6(Marking)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
5.1(Nomenclature)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
5.2(Diametral dimensions and tooth shape)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
5.3(Radial run-out)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
5.4(Axial run-out (wobble))	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
5.5(Pitch accuracy of sprocket teeth)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
5.6(Bore tolerance)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
5.7(Marking)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
3(Transmission chains)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
3.2(Designation)	-	0	-
3.3(Dimensions)	-	0	-
3.4.1(General)	-	0	-
3.4.2(Testing)	-	0	-
3.5(Preloading)	-	0	-
3.6(Length validation)	-	0	-
3.7(Marking)	-	0	-
4.1(General)	-	0	-
4.2(Nomenclature)	-	0	-
4.3(Designation)	-	0	-
4.4(Dimensions)	-	0	-
4.5(Length validation)	-	0	-
4.6(Marking)	-	0	-
4.7.1(General)	-	0	-
4.7.2(Nomenclature)	-	0	-
4.7.3(Designation)	-	0	-
4.7.4(Dimensions)	-	0	-
4.7.6(Marking)	-	0	-
5.1(Nomenclature)	-	0	-
5.2(Diametral dimensions and tooth shape)	-	0	-
5.3(Radial run-out)	-	0	-
5.4(Axial run-out (wobble))	-	0	-
5.5(Pitch accuracy of sprocket teeth)	-	0	-
5.6(Bore tolerance)	-	0	-
5.7(Marking)	-	0	-
3(Transmission chains)	-	0	-
3.2(Designation)	-	0	-
3.3(Dimensions)	-	0	-
3.4.1(General)	-	0	-
3.4.2(Testing)	-	0	-
3.5(Preloading)	-	0	-
3.6(Length validation)	-	0	-
3.7(Marking)	-	0	-
4.1(General)	-	0	-
4.2(Nomenclature)	-	0	-
4.3(Designation)	-	0	-
4.4(Dimensions)	-	0	-
4.5(Length validation)	-	0	-
4.6(Marking)	-	0	-
4.7.1(General)	-	0	-
4.7.2(Nomenclature)	-	0	-
4.7.3(Designation)	-	0	-
4.7.4(Dimensions)	-	0	-
4.7.6(Marking)	-	0	-
5.1(Nomenclature)	-	0	-
5.2(Diametral dimensions and tooth shape)	-	0	-
5.3(Radial run-out)	-	0	-
5.4(Axial run-out (wobble))	-	0	-
5.5(Pitch accuracy of sprocket teeth)	-	0	-
5.6(Bore tolerance)	-	0	-
5.7(Marking)	-	0	-
3(Transmission chains)	-	0	-
3.2(Designation)	-	0	-
3.3(Dimensions)	-	0	-
3.4.1(General)	-	0	-
3.4.2(Testing)	-	0	-
3.5(Preloading)	-	0	-
3.6(Length validation)	-	0	-
3.7(Marking)	-	0	-
4.1(General)	-	0	-
4.2(Nomenclature)	-	0	-
4.3(Designation)	-	0	-
4.4(Dimensions)	-	0	-
4.5(Length validation)	-	0	-
4.6(Marking)	-	0	-
4.7.1(General)	-	0	-
4.7.2(Nomenclature)	-	0	-
4.7.3(Designation)	-	0	-
4.7.4(Dimensions)	-	0	-
4.7.6(Marking)	-	0	-
5.1(Nomenclature)	-	0	-
5.2(Diametral dimensions and tooth shape)	-	0	-
5.3(Radial run-out)	-	0	-
5.4(Axial run-out (wobble))	-	0	-
5.5(Pitch accuracy of sprocket teeth)	-	0	-
5.6(Bore tolerance)	-	0	-
5.7(Marking)	-	0	-
3(Transmission chains)	-	-	-
3.2(Designation)	-	-	-
3.3(Dimensions)	-	-	-
3.4.1(General)	-	-	-
3.4.2(Testing)	-	-	-
3.5(Preloading)	-	-	-
3.6(Length validation)	-	-	-
3.7(Marking)	-	-	-
4.1(General)	-	-	-
4.2(Nomenclature)	-	-	-
4.3(Designation)	-	-	-
4.4(Dimensions)	-	-	-
4.5(Length validation)	-	-	-
4.6(Marking)	-	-	-
4.7.1(General)	-	-	-
4.7.2(Nomenclature)	-	-	-
4.7.3(Designation)	-	-	-
4.7.4(Dimensions)	-	-	-
4.7.6(Marking)	-	-	-
5.1(Nomenclature)	-	-	-
5.2(Diametral dimensions and tooth shape)	-	-	-
5.3(Radial run-out)	-	-	-
5.4(Axial run-out (wobble))	-	-	-
5.5(Pitch accuracy of sprocket teeth)	-	-	-
5.6(Bore tolerance)	-	-	-
5.7(Marking)	-	-	-

-
Included w.e.f.26.05.2025

209

IS 2619 (2018)

Glass beakers - Specification (Third Revision)

12400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-	12400	For Complete Testing
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-	12400	For Complete Testing
Cl.6 Material(Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)	-	12400	For Complete Testing
Cl.7.1 Dimensions(Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-	12400	For Complete Testing
Cl.7.2 Radius at base(Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-	12400	For Complete Testing
Cl.7.2 Radius at base(Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-	12400	For Complete Testing
Cl.7.3 Wall thickness(Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-	12400	For Complete Testing
Cl.8.1 Base(The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-	12400	For Complete Testing
8.2 Upper edge(The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-	12400	For Complete Testing
Cl. 8.3 Spout(The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-	12400	For Complete Testing
Cl.8.4 Scale(Beakers may be provided with a scale, which should approximately indicate the volume contained in the beaker.)	-	12400	For Complete Testing
Cl.8.5 Thermal shock resistance(Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-	12400	For Complete Testing
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-	12400	For Complete Testing
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-	12400	For Complete Testing
Cl.6 Material(Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)	-	12400	For Complete Testing
Cl.7.1 Dimensions(Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-	12400	For Complete Testing
Cl.7.2 Radius at base(Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-	12400	For Complete Testing
Cl.7.2 Radius at base(Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-	12400	For Complete Testing
Cl.7.3 Wall thickness(Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-	12400	For Complete Testing
Cl.8.1 Base(The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-	12400	For Complete Testing
8.2 Upper edge(The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-	12400	For Complete Testing
Cl. 8.3 Spout(The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-	12400	For Complete Testing
Cl.8.4 Scale(Beakers may be provided with a scale, which should approximately indicate the volume contained in the beaker.)	-	12400	For Complete Testing
Cl.8.5 Thermal shock resistance(Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-	12400	For Complete Testing
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-	12400	For Complete Testing
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-	12400	For Complete Testing
Cl.6 Material(Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)	-	12400	For Complete Testing
Cl.7.1 Dimensions(Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-	12400	For Complete Testing
Cl.7.2 Radius at base(Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-	12400	For Complete Testing
Cl.7.2 Radius at base(Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-	12400	For Complete Testing
Cl.7.3 Wall thickness(Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-	12400	For Complete Testing
Cl.8.1 Base(The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-	12400	For Complete Testing
8.2 Upper edge(The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-	12400	For Complete Testing
Cl. 8.3 Spout(The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-	12400	For Complete Testing
Cl.8.4 Scale(Beakers may be provided with a scale, which should approximately indicate the volume contained in the beaker.)	-	12400	For Complete Testing
Cl.8.5 Thermal shock resistance(Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-	12400	For Complete Testing

-
-

210

IS 915 (2012)

Laboratory glassware - One - Mark volumetric flasks (Third Revision)

11800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1(Material)	-	11800	For Complete Testing
Table 1(Internal Neck Diameter)	-	11800	For Complete Testing
Table 1(Distance of graduation line)	-	11800	For Complete Testing
Table 1(Overall Height)	-	11800	For Complete Testing
Table 1(Bulb Diameter)	-	11800	For Complete Testing
Table 1(Base Diameter)	-	11800	For Complete Testing
Table 1(Wall Thickness)	-	11800	For Complete Testing
Table 1(Ground joint k4)	-	11800	For Complete Testing
Table 1(Ground joint k6)	-	11800	For Complete Testing
8.3(Shape)	-	11800	For Complete Testing
8.4(Neck)	-	11800	For Complete Testing
8.5(Stopper)	-	11800	For Complete Testing
8.6(Dimensions)	-	11800	For Complete Testing
9.0(Graduation Line)	-	11800	For Complete Testing
Table-2(Nominal capacity)	-	11800	For Complete Testing
Table-2(Internal neck diameter)	-	11800	For Complete Testing
Table-2(Distance of graduation line 1))	-	11800	For Complete Testing
Table-2(Overall height 2))	-	11800	For Complete Testing
Table-2(Bulb diameter)	-	11800	For Complete Testing
Table-2(Base diameter)	-	11800	For Complete Testing
Table-2(Wall thickness)	-	11800	For Complete Testing
Table-2(Ground joint 3) k4)	-	11800	For Complete Testing
Table-2(Ground joint 3) k6)	-	11800	For Complete Testing
12.1(Visibility of graduation line, figures and marking)	-	11800	For Complete Testing
12.2(Visibility of graduation line, figures and marking)	-	11800	For Complete Testing
Table 1(Nominal Capacity)	-	11800	For Complete Testing

-
-

First
Prev
6
7
8
9
Next
Last

Bureau of Indian Standards

The National Standards Body of India

JBS TESTING SOLUTIONS PVT LTD (27), JALANDHAR

PLOT NO. 27, STREET NO. 2, ADJOINING FOCAL POINT ROAD, TRANSPORT NAGAR, JALANDHAR, PUNJAB, JALANDHAR, Jalandhar, Punjab, 144004

9988862929 jbstestingsolutions@gmail.com

Scope List