BIS - LIMS (Laboratory Information Management System)

JBS TESTING SOLUTIONS PVT LTD (27), JALANDHAR

PLOT NO. 27, STREET NO. 2, ADJOINING FOCAL POINT ROAD, TRANSPORT NAGAR, JALANDHAR, PUNJAB, JALANDHAR, Jalandhar, Punjab, 144004

9988862929 jbstestingsolutions@gmail.com

Scope List

Reset

334 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

211

IS 16172 (2023)

Reinforcement Couplers for Mechanical Splices of Steel Bars in Concrete ? Specification (first revision)

17500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Classification)	-	7500	For dimensional and other qualitative tests
6(Manufacture)	-	7500	For dimensional and other qualitative tests
7(Workmanship and Finish)	-	7500	For dimensional and other qualitative tests
8(Nominal Sizes)	-	7500	For dimensional and other qualitative tests
9.2.1(Tensile Strength)	-	10000	For mechanical tests
9.2.1.1(Disengagement test for threaded couplers)	-	10000	For mechanical tests
9.2.2(Percentage Elongation)	-	10000	For mechanical tests
9.3(Slip Test)	-	10000	For mechanical tests
9.4(Cyclic Tensile Test)	-	10000	For mechanical tests
9.5.1(Low cycle Fatigue Test)	-	10000	For mechanical tests
9.5.2(High Cycle Fatigue test)	-	10000	For mechanical tests
5(Classification)	-	0	-
6(Manufacture)	-	0	-
7(Workmanship and Finish)	-	0	-
8(Nominal Sizes)	-	0	-
9.2.1(Tensile Strength)	-	0	-
9.2.1.1(Disengagement test for threaded couplers)	-	0	-
9.2.2(Percentage Elongation)	-	0	-
9.3(Slip Test)	-	0	-
9.4(Cyclic Tensile Test)	-	0	-
9.5.1(Low cycle Fatigue Test)	-	0	-
9.5.2(High Cycle Fatigue test)	-	0	-

-
Included w.e.f.10.06.2025 Exclusion Cl 9.4 (Cyclic Tensile Test) Cl 9.5.1 (Low cycle Fatigue Test) Cl 9.5.2 (High Cycle Fatigue test)

212

IS 9997 (2023)

ALUMINIUM ALLOY REDRAW RODS FOR ELECTRICAL PURPOSES - SPECIFICATION

14800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.1(General requirements)	-	14800	For complete testing
Cl-5.2(Redraw rods)	-	14800	For complete testing
Cl-6(Manufacture)	-	14800	For complete testing
Cl-7.1, Table-2 (i)(Silicon)	-	14800	For complete testing
Cl-7.1, Table-2 (ii)(Iron)	-	14800	For complete testing
Cl-7.1, Table-2 (iii)(Copper)	-	14800	For complete testing
Cl-7.1, Table-2 (iv)(Manganese)	-	14800	For complete testing
Cl-7.1, Table-2 (v)(Magnesium)	-	14800	For complete testing
Cl-7.1, Table-2 (vi)(Chromium)	-	14800	For complete testing
Cl-7.1, Table-2 (vii)(Zinc)	-	14800	For complete testing
Cl-7.1, Table-2 (viii)(Boron)	-	14800	For complete testing
Cl-7.1, Table-2 (ix)(Vanadium + Titanium)	-	14800	For complete testing
Cl-7.1, Table-2 (x)(Other each)	-	14800	For complete testing
Cl-7.1, Table-2 (xi)(Others total)	-	14800	For complete testing
Cl-7.1, Table-2 (xii)(Aluminium)	-	14800	For complete testing
Cl-8.1, Table-3(UTS (MPa))	-	14800	For complete testing
Cl-8.1, Table-3(Elongation (%) - On 250 mm gauge length)	-	14800	For complete testing
Cl-8.1, Table-3(Resistivity (micro ohm.cm) at 20 oC)	-	14800	For complete testing
Cl-8.1, Table-3(Conductivity (%) (IACS))	-	14800	For complete testing
Cl-9(Electrical resistivity)	-	14800	For complete testing
Cl-10(Diameter and Permissible Variations)	-	14800	For complete testing
Cl-11(Joints)	-	14800	For complete testing
Cl-12(Finish and freedom from defects)	-	14800	For complete testing
Cl-16(Marking)	-	14800	For complete testing

-
Included w.e.f 30.05.2025

213

IS 1825 (1983)

Specification for aluminium alloy milk cans (Second Revision)

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 3.1,3.2,3.3(Copper)	-	7000	For Complete testing
Cl. 3.1,3.2,3.3(Manganese)	-	7000	For Complete testing
Cl. 3.1,3.2,3.3(Silicon)	-	7000	For Complete testing
Cl. 3.1,3.2,3.3(Iron)	-	7000	For Complete testing
Cl. 3.1,3.2,3.3(Aluminium)	-	7000	For Complete testing
Cl. 3.1,3.2,3.3(Magnesium)	-	7000	For Complete testing
Cl. 3.1,3.2,3.3(Zinc)	-	7000	For Complete testing
Cl. 3.1,3.2,3.3(Titanium)	-	7000	For Complete testing
Cl. 3.1,3.2,3.3(Vanadium)	-	7000	For Complete testing
Cl. 3.1,3.2,3.3(Chromium)	-	7000	For Complete testing
8(a) Rated Capacity)	-	7000	For Complete testing
8(b) Point of Capacity)	-	7000	For Complete testing
8(c) Batch OR Code No.)	-	7000	For Complete testing
8(d) BIS Mark)	-	7000	For Complete testing
8(e) Manufacturer's Trade Mark )	-	7000	For Complete testing
2(Capacity)	-	7000	For Complete testing
4 Fig. 1(Dimensions & Shape)	-	7000	For Complete testing
4 Fig. 1(A)	-	7000	For Complete testing
4 Fig. 1(B)	-	7000	For Complete testing
4 Fig. 1(C )	-	7000	For Complete testing
4 Fig. 1(D)	-	7000	For Complete testing
4 Fig. 1(E)	-	7000	For Complete testing
4 Fig. 1(F)	-	7000	For Complete testing
4 Fig. 1(G)	-	7000	For Complete testing
4 Fig. 1(H)	-	7000	For Complete testing
4 Fig. 1(BOTTOM BAND)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Drain Holes )	-	7000	For Complete testing
4 Fig. 1(HANDLE )	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(LID)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Hole Dia 8 ,2 holes)	-	7000	For Complete testing
4 Fig. 1(Hole Dia 12, 3 holes)	-	7000	For Complete testing
5(a)Transport cans shall consist of a body, bottom band)	-	7000	For Complete testing
5(lid and handles.)	-	7000	For Complete testing
5(b)Minimum Thickness(in mm))	-	7000	For Complete testing
5(i) Body and Neck)	-	7000	For Complete testing
5(ii) Bottom)	-	7000	For Complete testing
5(iii) Lid (Inner))	-	7000	For Complete testing
5(iv) Lid (Outer))	-	7000	For Complete testing
5(c) Mode of Shaping)	-	7000	For Complete testing
5(i) If the thickness at shoulder is less than 2.5 mm a )	-	7000	For Complete testing
5(reinforcement ring of 2 mm thickness shall be provided.)	-	7000	For Complete testing
5(ii) Brinell Hardness 85 HB Min.)	-	7000	For Complete testing
5(d) BOTTOM BAND- It shall be shrunk fit with a )	-	7000	For Complete testing
5(proper locking arrangement on the body. This shall)	-	7000	For Complete testing
5(be followed by brazing or welding all round.)	-	7000	For Complete testing
5(e) HANDLES (as per Cl 5.6))	-	7000	For Complete testing
5(f) SEALING LUG (as per Cl 5.7))	-	7000	For Complete testing
5(g)Workmanship and Finish- All brazing or welding shall )	-	7000	For Complete testing
5(be sound , free of porosity and shall be finished smooth .)	-	7000	For Complete testing
5(h) Mass 6.5 Kg. Min.)	-	7000	For Complete testing
7(i) Air Pressure Test (Cl 7.1))	-	7000	For Complete testing
7(ii) Drop Test (Cl 7.2))	-	7000	For Complete testing
7(iii) The cans when filled with water and inverted shall not show any profuse leakage through lids. )	-	7000	For Complete testing
8(a) Rated Capacity)	-	7000	For Complete testing
8(b) Point of Capacity)	-	7000	For Complete testing
8(c) Batch OR Code No.)	-	7000	For Complete testing
8(d) BIS Mark)	-	7000	For Complete testing
8(e) Manufacturer's Trade Mark )	-	7000	For Complete testing
2(Capacity)	-	7000	For Complete testing
4 Fig. 1(Dimensions & Shape)	-	7000	For Complete testing
4 Fig. 1(A)	-	7000	For Complete testing
4 Fig. 1(B)	-	7000	For Complete testing
4 Fig. 1(C )	-	7000	For Complete testing
4 Fig. 1(D)	-	7000	For Complete testing
4 Fig. 1(E)	-	7000	For Complete testing
4 Fig. 1(F)	-	7000	For Complete testing
4 Fig. 1(G)	-	7000	For Complete testing
4 Fig. 1(H)	-	7000	For Complete testing
4 Fig. 1(BOTTOM BAND)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Drain Holes )	-	7000	For Complete testing
4 Fig. 1(HANDLE )	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(LID)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Hole Dia 8 ,2 holes)	-	7000	For Complete testing
4 Fig. 1(Hole Dia 12, 3 holes)	-	7000	For Complete testing
5(a)Transport cans shall consist of a body, bottom band)	-	7000	For Complete testing
5(lid and handles.)	-	7000	For Complete testing
5(b)Minimum Thickness(in mm))	-	7000	For Complete testing
5(i) Body and Neck)	-	7000	For Complete testing
5(ii) Bottom)	-	7000	For Complete testing
5(iii) Lid (Inner))	-	7000	For Complete testing
5(iv) Lid (Outer))	-	7000	For Complete testing
5(c) Mode of Shaping)	-	7000	For Complete testing
5(i) If the thickness at shoulder is less than 2.5 mm a )	-	7000	For Complete testing
5(reinforcement ring of 2 mm thickness shall be provided.)	-	7000	For Complete testing
5(ii) Brinell Hardness 85 HB Min.)	-	7000	For Complete testing
5(d) BOTTOM BAND- It shall be shrunk fit with a )	-	7000	For Complete testing
5(proper locking arrangement on the body. This shall)	-	7000	For Complete testing
5(be followed by brazing or welding all round.)	-	7000	For Complete testing
5(e) HANDLES (as per Cl 5.6))	-	7000	For Complete testing
5(f) SEALING LUG (as per Cl 5.7))	-	7000	For Complete testing
5(g)Workmanship and Finish- All brazing or welding shall )	-	7000	For Complete testing
5(be sound , free of porosity and shall be finished smooth .)	-	7000	For Complete testing
5(h) Mass 6.5 Kg. Min.)	-	7000	For Complete testing
7(i) Air Pressure Test (Cl 7.1))	-	7000	For Complete testing
7(ii) Drop Test (Cl 7.2))	-	7000	For Complete testing
7(iii) The cans when filled with water and inverted shall not show any profuse leakage through lids. )	-	7000	For Complete testing
8(a) Rated Capacity)	-	7000	For Complete testing
8(b) Point of Capacity)	-	7000	For Complete testing
8(c) Batch OR Code No.)	-	7000	For Complete testing
8(d) BIS Mark)	-	7000	For Complete testing
8(e) Manufacturer's Trade Mark )	-	7000	For Complete testing
2(Capacity)	-	7000	For Complete testing
4 Fig. 1(Dimensions & Shape)	-	7000	For Complete testing
4 Fig. 1(A)	-	7000	For Complete testing
4 Fig. 1(B)	-	7000	For Complete testing
4 Fig. 1(C )	-	7000	For Complete testing
4 Fig. 1(D)	-	7000	For Complete testing
4 Fig. 1(E)	-	7000	For Complete testing
4 Fig. 1(F)	-	7000	For Complete testing
4 Fig. 1(G)	-	7000	For Complete testing
4 Fig. 1(H)	-	7000	For Complete testing
4 Fig. 1(BOTTOM BAND)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Drain Holes )	-	7000	For Complete testing
4 Fig. 1(HANDLE )	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(LID)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testingFor Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Dimension)	-	7000	For Complete testing
4 Fig. 1(Hole Dia 8 ,2 holes)	-	7000	For Complete testing
4 Fig. 1(Hole Dia 12, 3 holes)	-	7000	For Complete testing
5(a)Transport cans shall consist of a body, bottom band)	-	7000	For Complete testing
5(lid and handles.)	-	7000	For Complete testing
5(b)Minimum Thickness(in mm))	-	7000	For Complete testing
5(i) Body and Neck)	-	7000	For Complete testing
5(ii) Bottom)	-	7000	For Complete testing
5(iii) Lid (Inner))	-	7000	For Complete testing
5(iv) Lid (Outer))	-	7000	For Complete testing
5(c) Mode of Shaping)	-	7000	For Complete testing
5(i) If the thickness at shoulder is less than 2.5 mm a )	-	7000	For Complete testing
5(reinforcement ring of 2 mm thickness shall be provided.)	-	7000	For Complete testing
5(ii) Brinell Hardness 85 HB Min.)	-	7000	For Complete testing
5(d) BOTTOM BAND- It shall be shrunk fit with a )	-	7000	For Complete testing
5(proper locking arrangement on the body. This shall)	-	7000	For Complete testing
5(be followed by brazing or welding all round.)	-	7000	For Complete testing
5(e) HANDLES (as per Cl 5.6))	-	7000	For Complete testing
5(f) SEALING LUG (as per Cl 5.7))	-	7000	For Complete testing
5(g)Workmanship and Finish- All brazing or welding shall )	-	7000	For Complete testing
5(be sound , free of porosity and shall be finished smooth .)	-	7000	For Complete testing
5(h) Mass 6.5 Kg. Min.)	-	7000	For Complete testing
7(i) Air Pressure Test (Cl 7.1))	-	7000	For Complete testing
7(ii) Drop Test (Cl 7.2))	-	7000	For Complete testing
7(iii) The cans when filled with water and inverted shall not show any profuse leakage through lids. )	-	7000	For Complete testing

-
Included w.e.f 30.05.2025

214

IS 13724 (2018)

Hexagon thin nuts chamfered (Style 0) with metric fine pitch thread - Product grades A and B (Second Revision)

24100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Dimensions)	-	24100	For complete testing
4(Requirements and reference International Standards)	-	24100	For complete testing
4-Table 3(General requirements)	-	24100	For complete testing
4-Table 3(Thread)	-	24100	For complete testing
4-Table 3(Mechanical properties)	-	24100	For complete testing
4-Table 3(Tolerance)	-	24100	For complete testing
4-Table 3(Finish — Coating)	-	24100	For complete testing
4-Table 3(Surface integrity)	-	24100	For complete testing
4-Table 3(Acceptability)	-	24100	For complete testing
5(Designation)	-	24100	For complete testing

-
Included w.e.f.26.05.2025

215

IS 13723 (2018)

Hexagon High Nuts (Style 2) With Metric Fine Pitch Thread - Product Grades A and B (Second Revision)

24100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Dimensions)	-	24100	For complete testing
4(Requirements and reference International Standards)	-	24100	For complete testing
4-Table 3(General requirements)	-	24100	For complete testing
4-Table 3(Thread)	-	24100	For complete testing
4-Table 3(Mechanical properties)	-	24100	For complete testing
4-Table 3(Tolerance)	-	24100	For complete testing
4-Table 3(Finish — Coating)	-	24100	For complete testing
4-Table 3(Surface integrity)	-	24100	For complete testing
4-Table 3(Acceptability)	-	24100	For complete testing
5(Designation)	-	24100	For complete testing

-
Included w.e.f.26.05.2025

216

IS 7486 (2018)

Raised countersunk head screws (Common Head Style) with type H or type Z cross recess - Product grade A (Third Revision)

16650 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Dimensions)	-	16650	For complete testing
4, table 2(Material)	-	16650	For complete testing
4, table 2(General requirements)	-	16650	For complete testing
4, table 2(Thread)	-	16650	For complete testing
4, table 2(Mechanical property)	-	16650	For complete testing
4, table 2(Tolerances)	-	16650	For complete testing
4, table 2(Cross recess)	-	16650	For complete testing
4, table 2(Finish - coating)	-	16650	For complete testing
4, table 2(Surface integrity)	-	16650	For complete testing
4, table 2(Acceptability)	-	16650	For complete testing
5(Designation)	-	16650	For complete testing

-
Included w.e.f.21.05.2025

217

IS 7483 (2018)

Pan Head Screws With Type H or Type Z Cross Recess - Product Grade A (Third Revision)

19250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Dimensions)	-	19250	For complete testing
4, table 2(Material)	-	19250	For complete testing
4, table 2(General requirements)	-	19250	For complete testing
4, table 2(Thread)	-	19250	For complete testing
4, table 2(Mechanical property)	-	19250	For complete testing
4, table 2(Tolerances)	-	19250	For complete testing
4, table 2(Cross recess)	-	19250	For complete testing
4, table 2(Finish - coating)	-	19250	For complete testing
4, table 2(Surface integrity)	-	19250	For complete testing
4, table 2(Acceptability)	-	19250	For complete testing
5(Designation)	-	19250	For complete testing
3(Dimensions)	-	-	-
4, table 2(Material)	-	-	-
4, table 2(General requirements)	-	-	-
4, table 2(Thread)	-	-	-
4, table 2(Mechanical property)	-	-	-
4, table 2(Tolerances)	-	-	-
4, table 2(Cross recess)	-	-	-
4, table 2(Finish - coating)	-	-	-
4, table 2(Surface integrity)	-	-	-
4, table 2(Acceptability)	-	-	-
5(Designation)	-	-	-

-
Included w.e.f.21.05.2025

218

IS 15582 (2018)

Hexagon Bolts with Flange - Small Series - Product Grade A with Driving Feature of Product Grade B ( First Revision)

25400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Dimensions)	-	25400	For complete testing
4(Specifications and reference standards)	-	25400	For complete testing
4-Table 2(General requirements)	-	25400	For complete testing
4-Table 2(Thread)	-	25400	For complete testing
4-Table 2(Mechanical properties)	-	25400	For complete testing
4-Table 2(Tolerances)	-	25400	For complete testing
4-Table 2(Finish — Coating)	-	25400	For complete testing
4-Table 2(Surface integrity)	-	25400	For complete testing
4-Table 2(Acceptability)	-	25400	For complete testing
5(Designation)	-	25400	For complete testing

-
Included w.e.f.21.05.2025

219

IS 15581 (2018)

Hexagon nuts with flange, style 2 - Coarse thread (First Revision)

25400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Dimensions)	-	25400	For complete testing
4(Requirements and reference International Standards)	-	25400	For complete testing
4-Table 2(General requirements)	-	25400	For complete testing
4-Table 2(Thread)	-	25400	For complete testing
4-Table 2(Mechanical properties)	-	25400	For complete testing
4-Table 2(Tolerance)	-	25400	For complete testing
4-Table 2(Finish — Coating)	-	25400	For complete testing
4-Table 2(Surface integrity)	-	25400	For complete testing
4-Table 2(Acceptability)	-	25400	For complete testing
5(Designation)	-	25400	For complete testing

-
Included w.e.f.21.05.2025

220

IS 1364 : Part 6 (2018)

Hexagon Head Bolts, Screws and Nuts of Product Grades A and B Part 6 Hexagon Nuts, Style 2 ( First Revision )

24800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Dimensions)	-	24800	For complete testing
4, table 3(General requirements)	-	24800	For complete testing
4, table 3(Thread)	-	24800	For complete testing
4, table 3(Mechanical properties)	-	24800	For complete testing
4, table 3(Tolerances)	-	24800	For complete testing
4, table 3(Finish-coating)	-	24800	For complete testing
4, table 3(Surface integrity)	-	24800	For complete testing
4, table 3(Acceptability)	-	24800	For complete testing
5(Designation)	-	24800	For complete testing

-
-

221

IS 1364 : Part 4 (2003)

Hexagon head bolts, screws and nuts of product grades A and B: Part 4 hexagon thin nuts (Chamfered) (Size Range M1.6t0 M64) (Fourth Revision)

24800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Dimensions)	-	24800	For complete testing
4, table 3(General requirements)	-	24800	For complete testing
4, table 3(Thread)	-	24800	For complete testing
4, table 3(Mechanical properties)	-	24800	For complete testing
4, table 3(Tolerances)	-	24800	For complete testing
4, table 3(Finish-coating)	-	24800	For complete testing
4, table 3(Surface integrity)	-	24800	For complete testing
4, table 3(Acceptability)	-	24800	For complete testing
5(Designation)	-	24800	For complete testing

-
Included w.e.f.21.05.2025

222

IS 13382 (2018)

Cast iron specials for mechanical and push-on flexible joints for pressure pipes for water, gas and sewage - Specification (Second Revision)

18900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Thickness Wall, mm )	-	18900	For complete testing
7(Joints)	-	18900	For complete testing
7.1(Type of Joints)	-	18900	For complete testing
7.2(Push on joints)	-	18900	For complete testing
7.3(Flange and mechanical joints)	-	18900	For complete testing
7.4(Bolt and hole circle)	-	18900	For complete testing
7.5(Flanges)	-	18900	For complete testing
7.6(Flanges)	-	18900	For complete testing
8(Rubber gaskets)	-	18900	For complete testing
8.2(Dimenmsions of Rubber gaskets)	-	18900	For complete testing
10(Mechanical Test)	-	18900	For complete testing
10.1(Tensile Stregth, Mpa)	-	18900	For complete testing
10.2(Hardness, HBW)	-	18900	For complete testing
11(Hydrostatic test)	-	18900	For complete testing
11.2(Withstand Hydrostatic Pressure)	-	18900	For complete testing
12(Sizes)	-	18900	For complete testing
12.2(Dimensions, mm)	-	18900	For complete testing
12.2(e)	-	18900	For complete testing
12.2(R)	-	18900	For complete testing
12.2(L)	-	18900	For complete testing
12.2(Socket)	-	18900	For complete testing
12.2(D)	-	18900	For complete testing
12.2(Cylinder Pipe)	-	18900	For complete testing
12.2(b)	-	18900	For complete testing
12.2(D1)	-	18900	For complete testing
12.2(W)	-	18900	For complete testing
12.2(P)	-	18900	For complete testing
12.2(X)	-	18900	For complete testing
12.2(Y)	-	18900	For complete testing
12.2(Z)	-	18900	For complete testing
12.2(S)	-	18900	For complete testing
12.2(Follower Gland)	-	18900	For complete testing
12.2(D)	-	18900	For complete testing
12.2(C )	-	18900	For complete testing
12.2(E)	-	18900	For complete testing
12.2(F)	-	18900	For complete testing
12.2(Hole Dia)	-	18900	For complete testing
12.2(N)	-	18900	For complete testing
12.2(M)	-	18900	For complete testing
12.2(A)	-	18900	For complete testing
12.2(Dia of Bolt)	-	18900	For complete testing
12.2(L)	-	18900	For complete testing
12.2(No of Bolt)	-	18900	For complete testing
12.2(Rubber Gasket )	-	18900	For complete testing
12.2(N)	-	18900	For complete testing
12.2(Q)	-	18900	For complete testing
12.2(R)	-	18900	For complete testing
12.2(T)	-	18900	For complete testing
12.2(U)	-	18900	For complete testing
12.2(V)	-	18900	For complete testing
14(Coating Test at 0 and 65 Degree Centegrade)	-	18900	For complete testing
15(Internal Lining)	-	18900	For complete testing
15.1(Cement mortor lining)	-	18900	For complete testing
17.2(Flexible Joints)	-	18900	For complete testing
18.1(Positive internal hydrostatic pressure)	-	18900	For complete testing
18.3(Stregth and Leak tightness test for flanged joints)	-	18900	For complete testing
6(Thickness Wall, mm )	-	18900	For complete testing
7(Joints)	-	18900	For complete testing
7.1(Type of Joints)	-	18900	For complete testing
7.2(Push on joints)	-	18900	For complete testing
7.3(Flange and mechanical joints)	-	18900	For complete testing
7.4(Bolt and hole circle)	-	18900	For complete testing
7.5(Flanges)	-	18900	For complete testing
7.6(Flanges)	-	18900	For complete testing
8(Rubber gaskets)	-	18900	For complete testing
8.2(Dimenmsions of Rubber gaskets)	-	18900	For complete testing
10(Mechanical Test)	-	18900	For complete testing
10.1(Tensile Stregth, Mpa)	-	18900	For complete testing
10.2(Hardness, HBW)	-	18900	For complete testing
11(Hydrostatic test)	-	18900	For complete testing
11.2(Withstand Hydrostatic Pressure)	-	18900	For complete testing
12(Sizes)	-	18900	For complete testing
12.2(Dimensions, mm)	-	18900	For complete testing
12.2(e)	-	18900	For complete testing
12.2(R)	-	18900	For complete testing
12.2(L)	-	18900	For complete testing
12.2(Socket)	-	18900	For complete testing
12.2(D)	-	18900	For complete testing
12.2(Cylinder Pipe)	-	18900	For complete testing
12.2(b)	-	18900	For complete testing
12.2(D1)	-	18900	For complete testing
12.2(W)	-	18900	For complete testing
12.2(P)	-	18900	For complete testing
12.2(X)	-	18900	For complete testing
12.2(Y)	-	18900	For complete testing
12.2(Z)	-	18900	For complete testing
12.2(S)	-	18900	For complete testing
12.2(Follower Gland)	-	18900	For complete testing
12.2(D)	-	18900	For complete testing
12.2(C )	-	18900	For complete testing
12.2(E)	-	18900	For complete testing
12.2(F)	-	18900	For complete testing
12.2(Hole Dia)	-	18900	For complete testing
12.2(N)	-	18900	For complete testing
12.2(M)	-	18900	For complete testing
12.2(A)	-	18900	For complete testing
12.2(Dia of Bolt)	-	18900	For complete testing
12.2(L)	-	18900	For complete testing
12.2(No of Bolt)	-	18900	For complete testing
12.2(Rubber Gasket )	-	18900	For complete testing
12.2(N)	-	18900	For complete testing
12.2(Q)	-	18900	For complete testing
12.2(R)	-	18900	For complete testing
12.2(T)	-	18900	For complete testing
12.2(U)	-	18900	For complete testing
12.2(V)	-	18900	For complete testing
14(Coating Test at 0 and 65 Degree Centegrade)	-	18900	For complete testing
15(Internal Lining)	-	18900	For complete testing
15.1(Cement mortor lining)	-	18900	For complete testing
17.2(Flexible Joints)	-	18900	For complete testing
18.1(Positive internal hydrostatic pressure)	-	18900	For complete testing
18.3(Stregth and Leak tightness test for flanged joints)	-	18900	For complete testing

-
Included w.e.f.21.05.2025

223

IS 513 : Part 1 (2016)

Cold reduced carbon steel sheet and strip: Part 1 cold forming and drawing purpose (Sixth Revision)

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Chemical Composition)	-	7000	For complete testing
8(Mechanical and Physical Properties)	-	7000	For complete testing
Cl 8(UTM)	-	7000	For complete testing
Cl 9(Workmanship)	-	7000	For complete testing
Cl 9.6(Workmanship)	-	7000	For complete testing
Cl 10(Workmanship)	-	7000	For complete testing
Cl 11(Length, Width & Thickness)	-	7000	For complete testing
Cl 8(UTM)	-	7000	For complete testing
Cl 9.5(Workmanship)	-	7000	For complete testing
Cl 9.6(Workmanship)	-	7000	For complete testing
Cl 10(Workmanship)	-	7000	For complete testing
Cl 11(Length, Width & Thickness)	-	7000	For complete testing
Cl 8(UTM)	-	7000	For complete testing
Cl 9(Workmanship)	-	7000	For complete testing
Cl 9.6(Workmanship)	-	7000	For complete testing
Cl 10(Workmanship)	-	7000	For complete testing
Cl 11(Length, Width & Thickness)	-	7000	For complete testing
7.0(ALUMINIUM)	-	7000	For complete testing
7.0(MICRO ALLOYS)	-	7000	For complete testing
7.0(NITROGEN)	-	7000	For complete testing
7.0(SILICON)	-	7000	For complete testing
7.0(MANGANESE)	-	7000	For complete testing
7.0(PHOSPHORUS)	-	7000	For complete testing
7.0(SULPHUR)	-	7000	For complete testing
7.0(CARBON)	-	7000	For complete testing
Cl. 11(Out of square)	-	7000	For complete testing
Cl. 11(Flatness)	-	7000	For complete testing
Cl. 11(Camber)	-	7000	For complete testing
Cl. 11(Width)	-	7000	For complete testing
Cl. 11(Thickness)	-	7000	For complete testing
Cl. 8.7(Bake Hardening Index)	-	7000	For complete testing
Cl. 8.6 Table 5A, 5B & 5C(Tensile Strain Hardening Component (n-Value))	-	7000	For complete testing
Cl. 8.5 Table 5A, 5B & 5C(Plastic Strain Ratio (r bar/r-90))	-	7000	For complete testing
Cl. 8.4(Bend Test)	-	7000	For complete testing
Cl. 8.3 Table 6(Hardness Test ( Only for CR0 & CR1))	-	7000	For complete testing
Cl. 8.2(Cupping Test(Only for sheet and coils CR2, CR3, CR4(having thickness 0.5 mm-2.0 mm))	-	7000	For complete testing
Cl. 8.1 & Table 5A, 5B & 5C(Elongation at 80 mm gauge length)	-	7000	For complete testing
Cl. 8.1 & Table 5A, 5B & 5C(Elongation at 50 mm gauge length)	-	7000	For complete testing
Cl. 8.1 & Table 5A, 5B & 5C(Yield Stress)	-	7000	For complete testing
Cl. 9 Table 8(Surface roughness)	-	7000	For complete testing
Cl 11(Length, Width & Thickness)	-	7000	For complete testing
Cl 10(Workmanship)	-	7000	For complete testing
Cl 9.6(Workmanship)	-	7000	For complete testing
Cl 9(Workmanship)	-	7000	For complete testing
Cl 8(UTM)	-	7000	For complete testing
Cl 8(UTM)	-	7000	For complete testing
Cl 9(Workmanship)	-	7000	For complete testing
Cl 9.6(Workmanship)	-	7000	For complete testing
Cl 10(Workmanship)	-	7000	For complete testing
Cl 11(Thickness (08))	-	7000	For complete testing
Cl 7(UTM)	-	7000	For complete testing
8.1(Mechanical)	-	7000	For complete testing
8.2(Cupping test)	-	7000	For complete testing
8.3(Hardness HRB/HV)	-	7000	For complete testing
8.4(Bend Test)	-	7000	For complete testing
8.5(Plastic strain ratio)	-	7000	For complete testing
8.6(Tensile strain Hardening component)	-	7000	For complete testing
8.7(Black Hardening Index)	-	7000	For complete testing
9(Surface finish)	-	7000	For complete testing
10(Freedom from defects)	-	7000	For complete testing
13(Marking)	-	7000	For complete testing
Cl. 7.3(Carbon)	-	7000	For complete testing
Cl. 7.3(Manganese)	-	7000	For complete testing
Cl. 7.3(Suphur)	-	7000	For complete testing
Cl. 7.3(Phosphorus)	-	7000	For complete testing
Cl. 7.3(Silicon)	-	7000	For complete testing

-
Included w.e.f.21.05.2025

224

IS 3312 (2021)

Steel Shelving Cabinets ( Adjustable Type ) - Specification ( Third Revision )

37500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
15(MARKING)	-	37500	For complete testing
15(MARKING)	-	37500	For complete testing
4.1(DIMENSIONS)	-	37500	For complete testing
4.1(DIMENSIONS)	-	37500	For complete testing
4.1(DIMENSIONS)	-	37500	For complete testing
4.1(DIMENSIONS)	-	37500	For complete testing
4.1(DIMENSIONS)	-	37500	For complete testing
4.1(DIMENSIONS)	-	37500	For complete testing
4.1(DIMENSIONS)	-	37500	For complete testing
4.1(DIMENSIONS)	-	37500	For complete testing
5(FABRICATION)	-	37500	For complete testing
5.1(Sides)	-	37500	For complete testing
5.1(Sides)	-	37500	For complete testing
5.2(Back)	-	37500	For complete testing
5.2(Back)	-	37500	For complete testing
5.3(Top and Bottom)	-	37500	For complete testing
5.3(Top and Bottom)	-	37500	For complete testing
5.5(Shelves)	-	37500	For complete testing
5.5(Shelves)	-	37500	For complete testing
5.5(Shelves)	-	37500	For complete testing
5.5(Shelves)	-	37500	For complete testing
5.5(Shelves)	-	37500	For complete testing
5.5(Shelves)	-	37500	For complete testing
5.5(Shelves)	-	37500	For complete testing
5.5.1(Self supporting Arrangement)	-	37500	For complete testing
5.6(Doors)	-	37500	For complete testing
5.6.1(Right Door)	-	37500	For complete testing
5.6.1(Right Door)	-	37500	For complete testing
5.6.1(Right Door)	-	37500	For complete testing
5.6.1(Right Door)	-	37500	For complete testing
5.6.2(Left Door)	-	37500	For complete testing
5.6.2(Left Door)	-	37500	For complete testing
5.7(Pedestal)	-	37500	For complete testing
5.7(Pedestal)	-	37500	For complete testing
5.8(Hinges)	-	37500	For complete testing
5.7(Pedestal)	-	37500	For complete testing
5.8(Hinges)	-	37500	For complete testing
5.8(Hinges)	-	37500	For complete testing
5.7(Pedestal)	-	37500	For complete testing
5.9(Locks)	-	37500	For complete testing
5.10(Lockers)	-	37500	For complete testing
5.10(Lockers)	-	37500	For complete testing
5.10(Lockers)	-	37500	For complete testing
5.10(Lockers)	-	37500	For complete testing
5.10.2(Doors)	-	37500	For complete testing
5.10.2(Doors)	-	37500	For complete testing
5.10.2(Doors)	-	37500	For complete testing
5.10.2(Doors)	-	37500	For complete testing
5.10.3(Locks)	-	37500	For complete testing
5.10.4(Drawer)	-	37500	For complete testing
5.10.5(Drawer)	-	37500	For complete testing
5.10.6(Drawer)	-	37500	For complete testing
5.10.7(Drawer)	-	37500	For complete testing
5.10.7(Drawer)	-	37500	For complete testing
5.10.7(Drawer)	-	37500	For complete testing
5.10.7(Drawer)	-	37500	For complete testing
6(ASSEMBLY)	-	37500	For complete testing
7(ADDITIONAL ACCESSORIES)	-	37500	For complete testing
8(Loading (Table 3))	-	37500	For complete testing
9(Finish)	-	37500	For complete testing
9.1.1(Steel Sheet Components)	-	37500	For complete testing
9.1.1(Steel Sheet Components)	-	37500	For complete testing
9.1.3(Steel Sheet Components)	-	37500	For complete testing
9.1.3(Steel Sheet Components)	-	37500	For complete testing
9.1.3(Steel Sheet Components)	-	37500	For complete testing
9.2(Steel Sheet Components)	-	37500	For complete testing
15(MARKING)	-	-	-
15(MARKING)	-	-	-
4.1(DIMENSIONS)	-	-	-
4.1(DIMENSIONS)	-	-	-
4.1(DIMENSIONS)	-	-	-
4.1(DIMENSIONS)	-	-	-
4.1(DIMENSIONS)	-	-	-
4.1(DIMENSIONS)	-	-	-
4.1(DIMENSIONS)	-	-	-
4.1(DIMENSIONS)	-	-	-
5(FABRICATION)	-	-	-
5.1(Sides)	-	-	-
5.1(Sides)	-	-	-
5.2(Back)	-	-	-
5.2(Back)	-	-	-
5.3(Top and Bottom)	-	-	-
5.3(Top and Bottom)	-	-	-
5.5(Shelves)	-	-	-
5.5(Shelves)	-	-	-
5.5(Shelves)	-	-	-
5.5(Shelves)	-	-	-
5.5(Shelves)	-	-	-
5.5(Shelves)	-	-	-
5.5(Shelves)	-	-	-
5.5.1(Self supporting Arrangement)	-	-	-
5.6(Doors)	-	-	-
5.6.1(Right Door)	-	-	-
5.6.1(Right Door)	-	-	-
5.6.1(Right Door)	-	-	-
5.6.1(Right Door)	-	-	-
5.6.2(Left Door)	-	-	-
5.6.2(Left Door)	-	-	-
5.7(Pedestal)	-	-	-
5.7(Pedestal)	-	-	-
5.8(Hinges)	-	-	-
5.7(Pedestal)	-	-	-
5.8(Hinges)	-	-	-
5.8(Hinges)	-	-	-
5.7(Pedestal)	-	-	-
5.9(Locks)	-	-	-
5.10(Lockers)	-	-	-
5.10(Lockers)	-	-	-
5.10(Lockers)	-	-	-
5.10(Lockers)	-	-	-
5.10.2(Doors)	-	-	-
5.10.2(Doors)	-	-	-
5.10.2(Doors)	-	-	-
5.10.2(Doors)	-	-	-
5.10.3(Locks)	-	-	-
5.10.4(Drawer)	-	-	-
5.10.5(Drawer)	-	-	-
5.10.6(Drawer)	-	-	-
5.10.7(Drawer)	-	-	-
5.10.7(Drawer)	-	-	-
5.10.7(Drawer)	-	-	-
5.10.7(Drawer)	-	-	-
6(ASSEMBLY)	-	-	-
7(ADDITIONAL ACCESSORIES)	-	-	-
8(Loading (Table 3))	-	-	-
9(Finish)	-	-	-
9.1.1(Steel Sheet Components)	-	-	-
9.1.1(Steel Sheet Components)	-	-	-
9.1.3(Steel Sheet Components)	-	-	-
9.1.3(Steel Sheet Components)	-	-	-
9.1.3(Steel Sheet Components)	-	-	-
9.2(Steel Sheet Components)	-	-	-

-
Included w.e.f.21.05.2025

225

IS 5820 (2024)

PRECAST CONCRETE CABLE COVERS â SPECIFICATION (first revision)

19500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(Cement)	-	19500	For complete testing
Cl-4.2(Aggregates)	-	19500	For complete testing
Cl-4.3(Pulverized Fuel Ash)	-	19500	For complete testing
Cl-4.4(Water)	-	19500	For complete testing
Cl-4.5(Steel Wire or Rod)	-	19500	For complete testing
Cl-5(Manufacture)	-	19500	For complete testing
Cl-6(Design)	-	19500	For complete testing
Cl-7.1(cable covers)	-	19500	For complete testing
Cl-7.2(Dimensions)	-	19500	For complete testing
Cl-7.3(Impact Strength)	-	19500	For complete testing
Cl-8.2(Number of Tests)	-	19500	For complete testing
Cl-11(Marking)	-	19500	For complete testing

-
Included w.e.f.21.05.2025

226

IS 9295 (2024)

STEEL TUBES FOR IDLERS FOR BELT CONVEYORS - SPECIFICATION (second revision)

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
As per Clause 5(Types /Grade and Designation)	-	12500	For complete testing
As per clause 6(Material)	-	12500	For complete testing
As per clause 7(Manufacture)	-	12500	For complete testing
As per clause 7.1.5(Sulphur)	-	12500	For complete testing
As per clause 7.1.6(Phosphorus)	-	12500	For complete testing
As per clause 8(Mechanical Properties)	-	12500	For complete testing
As per clause 8.1(Tensile Test)	-	12500	For complete testing
As per clause 8.1.1(Yield Stress)	-	12500	For complete testing
As per clause 8.1.2(Elongation)	-	12500	For complete testing
As per clause 8.2(Drift Expansion Test)	-	12500	For complete testing
As per clause 8.3(Flattening Test)	-	12500	For complete testing
Cl-9.1, Table-2(Outside Diameter)	-	12500	For complete testing
As per clause 10(Hardness Test)	-	12500	For complete testing
As per clause 11(Mechanical Test)	-	12500	For complete testing
As per clause 12(Retests)	-	12500	For complete testing
As per clause 13(Dimension Tolerance)	-	12500	For complete testing
As per clause 14(Workmanship)	-	12500	For complete testing
As per clause 15(Straightness)	-	12500	For complete testing
As per clause 16(Length)	-	12500	For complete testing
As per clause 17(Surface Protection)	-	12500	For complete testing
As per clause 18(Marking)	-	12500	For complete testing

-
Included w.e.f.21.05.2025

227

IS 712 (1984)

Specification for building limes (Third Revision)

18500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4 ,Table 1(Chem reqd)	-	18500	For complete testing
cl 4, Table 2(Physical reqd)	-	18500	For complete testing
Cl. 4.1 - Table 1 - i(Calcium and Magnesium Oxides, on ignited basis - IS 6932 (part 1) : 1973)	-	18500	For complete testing
Cl. 4.1 - Table 1 - ii(Magnesium Oxides, on ignited basis - IS 6932 (part 1) : 1973)	-	18500	For complete testing
Cl. 4.1 - Table 1 - iii(Silica, Alumina and Ferric oxide, on ignited basis - IS 6932 (part 1) : 1973)	-	18500	For complete testing
Cl. 4.1 - Table 1 - iv(Unhydrated Magnesium oxide, on ignited basis - IS 6932 (part 5) : 1973)	-	18500	For complete testing
Cl. 4.1 - Table 1 - v(Insoluble Residue in dilute acid and alkali, on ignited basis - IS 6932 (part 1) : 1973)	-	18500	For complete testing
Cl. 4.1 - Table 1 - vi(Carbondioxide on oven dried basis - IS 6932 (part 2) : 1973)	-	18500	For complete testing
Cl. 4.1 - Table 1 - vii(Free moisture content - IS 1514 : 1959)	-	18500	For complete testing
Cl. 4.1 - Table 1 - viii(Available lime as CaO (dry basis) - IS 1514 : 1959)	-	18500	For complete testing
Clauses 5.1 Table No. 2, SI No. (ix) (Popping Pitting)	-	18500	For complete testing
Clauses 5.1 Table No. 2, SI No. (viii) (Soundness- Le chatelier Expansion)	-	18500	For complete testing
Clauses 5.1 Table No. 2, SI No. (vii) (Volume yield)	-	18500	For complete testing
Clauses 5.1 Table No. 2, SI No. (vi) (Workability Bumps)	-	18500	For complete testing
Clauses 5.1 Table No. 2, SI No. (v) (Transverse strength at 28 days)	-	18500	For complete testing
Clauses 5.1 Table No. 2, SI No. (iv) b) (Compressive strength at 28 days)	-	18500	For complete testing
Clauses 5.1 Table No. 2, SI No. (iv) a) (Compressive strength at 14 days)	-	18500	For complete testing
Clauses 5.1 Table No. 2, SI No. (iii) b) (Final Setting time)	-	18500	For complete testing
Clauses 5.1 Table No. 2, SI No. (iii) a) (Initial Setting time)	-	18500	For complete testing
Clauses 5.1 Table No. 2, SI No. (ii) b) (Residue on slaking (Residue on 300 micron IS sieve))	-	18500	For complete testing
Clauses 5.1 Table No. 2, SI No. (ii) a) (Residue on slaking (Residue on 850 micron IS sieve))	-	18500	For complete testing
Clauses 5.1 Table No. 2, SI No. (i) c) (Fineness- (Residue on 212 micron IS Sieve))	-	18500	For complete testing
Clauses 5.1 Table No. 2, SI No. (i) b) (Fineness- (Residue on 300 micron IS Sieve))	-	18500	For complete testing
Clauses 5.1 Table No. 2, SI No. (i) a) (Fineness- (Residue on 2.36 mm IS Sieve))	-	18500	For complete testing

-
Included w.e.f.21.05.2025

228

IS 3589 (2001)

Steel pipes for water and sewage (168.3 To 2540 Mm Outside Diameter) - Specification (Third Revision)

9800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1 Table 2 Table 3(Carbon Content IS 228)	-	9800	For complete testing
8.1 Table 2 Table 3(Carbon Content IS 228)	-	9800	For complete testing
8.1 Table 2 Table 3(Carbon Content IS 228)	-	9800	For complete testing
8.1 Table 2 Table 3(Manganese Content IS 228)	-	9800	For complete testing
8.1 Table 2 Table 3(Manganese Content IS 228)	-	9800	For complete testing
8.1 Table 2 Table 3(Manganese Content IS 228)	-	9800	For complete testing
8.1 Table 2 Table 3(Phosphorus Content IS 228)	-	9800	For complete testing
8.1 Table 2 Table 3(Sulphur Content IS 228)	-	9800	For complete testing
9.3(Guided bend test(For SAW Pipes))	-	9800	For complete testing
10(Hydaulic pressure test)	-	9800	For complete testing
11.1, Table 5.(Outside Diameter (OD))	-	9800	For complete testing
11.1, Table 5.(Thickness)	-	9800	For complete testing
11.1, Table 5.(Mass)	-	9800	For complete testing
12.3.3(Ovality)	-	9800	For complete testing
12.5(Strightness)	-	9800	For complete testing
14.1(Visual inspection, Appearance and Workmanship)	-	9800	For complete testing
14.2(Visual inspection, Appearance and Workmanship)	-	9800	For complete testing
14.3(Visual inspection, Appearance and Workmanship)	-	9800	For complete testing
14.4(Visual inspection, Appearance and Workmanship-Dent Depth(below 610 mm OD))	-	9800	For complete testing
14.4(Visual inspection, Appearance and Workmanship-Dent Depth(Above 610 mm OD))	-	9800	For complete testing
14.4(Visual inspection, Appearance and Workmanship-Dent Length)	-	9800	For complete testing
14.4(Visual inspection, Appearance and Workmanship-Dent Length)	-	9800	For complete testing
8.1(CE)	-	9800	For complete testing
8.1(CE)	-	9800	For complete testing
8.1(CE)	-	9800	For complete testing
9.3(Guided Bend Test (for SAW Pipes))	-	9800	For complete testing
9.2.3(Flattening Test for seamless pipes)	-	9800	For complete testing
9.2.1(Flattening test for ERW pipes )	-	9800	For complete testing
9.1(Tensile test-Yield Strength)	-	9800	For complete testing
9.1(Tensile test-Strength)	-	9800	For complete testing
9.1(Tensile test- Elongation)	-	9800	For complete testing
18(Marking)	-	9800	For complete testing
18(Marking)	-	9800	For complete testing

-
Included w.e.f.21.05.2025

229

IS 14650 (1999)

Carbon steel cast billet ingots, billets, blooms and slabs for re-rolling purposes - Specificaation

8200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Carbon- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	8200	For complete testing
6(Manganese- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	8200	For complete testing
6(Silicon- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	8200	For complete testing
6(Nitrogen- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	8200	For complete testing
6(Aluminium- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	8200	For complete testing
6(Titanium- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	8200	For complete testing
6(Vanadium- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	8200	For complete testing
6(Nickel- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	8200	For complete testing
6(Chromium- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	8200	For complete testing
6(Copper- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	8200	For complete testing
6(Molybdenum- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	8200	For complete testing
6(Niobium- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	8200	For complete testing
9 & 10(Dimensions and Tolerances )	-	8200	For complete testing
11(Freedom from Defects )	-	8200	For complete testing
12(Macro-examination )	-	8200	For complete testing
12(Sulphur Print Tests )	-	8200	For complete testing
Cl. 6.1(Nitrogen)	-	8200	For complete testing
Cl. 6.1(Niobium)	-	8200	For complete testing
Cl. 6.1(Titanium)	-	8200	For complete testing
Cl. 6.1(Copper)	-	8200	For complete testing
Cl. 6.1(Aluminium)	-	8200	For complete testing
Cl. 6.1(Molybdenum)	-	8200	For complete testing
Cl. 6.1(Chromium)	-	8200	For complete testing
Cl. 6.1(Vanadium)	-	8200	For complete testing
Cl. 6.1(Nickel)	-	8200	For complete testing
Cl. 6.1(Manganese)	-	8200	For complete testing
Cl. 6.1(Silicon)	-	8200	For complete testing
Cl. 6.1(Carbon)	-	8200	For complete testing
6("Total content of elements (Cr+Cu+Ni+Mo+P)-IS:228 ")	-	8200	For complete testing
6(Sulphur + Phosphorus - IS:228)	-	8200	For complete testing
6(Micro alloying elements (Nb+V+Ti+B))	-	8200	For complete testing
11.4 (i)(Bend)	-	8200	For complete testing
11.4 (ii)(Out of Square)	-	8200	For complete testing
11.4 (iii)(Scarfing pits)	-	8200	For complete testing
5(Manufacture)	-	8200	For complete testing
13(Marking)	-	8200	For complete testing

-
Included w.e.f.21.05.2025

230

IS 17190 (2020)

Grouts for Filling of Joints of Tiles and Stones - Specification

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5-Table 1-(i)(Linear shrinkage, percent, Max)	-	25000	For complete testing
5-Table 1-(ii)(Water absorption after 30 min, percent, Max)	-	25000	For complete testing
5-Table 1-(iii)(Water absorption after 240 min, percent, Max (optional))	-	25000	For complete testing
5-Table 1-(iv)(Compressive strength, MPa, Min)	-	25000	For complete testing
5-Table 1-(v)(Flexural strength, MPa, Min)	-	25000	For complete testing
5-Table 1-(vi)(Abrasion resistance, percent, Max)	-	25000	For complete testing
5-Table 1-(vii)(Chemical resistance (optional))	-	25000	For complete testing
5-Table 1-(viii)(Transverse deformation, mm, Min)	-	25000	For complete testing
6(Packing)	-	25000	For complete testing
7(Marking)	-	25000	For complete testing

-
Included w.e.f.21.05.2025

231

IS 2414 (2005)

Cycle and rickshaw pneumatic tyres - Specification (Fourth Revision)

21000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Type)	-	21000	For complete testing
4.2(Designation)	-	21000	For complete testing
5.1 & 5.2(Dimensions)	-	21000	For complete testing
6.1(Construction)	-	21000	For complete testing
6.2(Tyre Cord)	-	21000	For complete testing
6.3(Tyre Casing Strength)	-	21000	For complete testing
6.4(Bead Wire Joint)	-	21000	For complete testing
6.5(Requirements of Ruber Compound)	-	21000	For complete testing
6.6(Adhesion test)	-	21000	For complete testing
6.7(Performance test)	-	21000	For complete testing
4.1(Type)	-	21000	For complete testing
4.2(Designation)	-	21000	For complete testing
5.1 & 5.2(Dimensions)	-	21000	For complete testing
6.1(Construction)	-	21000	For complete testing
6.2(Tyre Cord)	-	21000	For complete testing
6.3(Tyre Casing Strength)	-	21000	For complete testing
6.4(Bead Wire Joint)	-	21000	For complete testing
6.5(Requirements of Ruber Compound)	-	21000	For complete testing
6.6(Adhesion test)	-	21000	For complete testing
6.7(Performance test)	-	21000	For complete testing
6.7(Requirements)	-	21000	For complete testing
6.6(Requirements)	-	21000	For complete testing
6.5(Requirements)	-	21000	For complete testing
6.4(Requirements)	-	21000	For complete testing
6.3(Requirements)	-	21000	For complete testing
6.2(Requirements)	-	21000	For complete testing
6.1(Requirements)	-	21000	For complete testing
5.1 & 5.2(Type & Designattion)	-	21000	For complete testing
4.2(Type & Designattion)	-	21000	For complete testing
4.1(Type & Designattion)	-	21000	For complete testing

-
Included w.e.f.21.05.2025

232

IS 15911 (2010)

Structural steel (Ordinary Quality) - Specification

9500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Table-1, 5.1, 8.1 & 8.2(Carbon: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	9500	For complete testing
Table-1, 5.1, 8.1 & 8.2(Sulphur: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	9500	For complete testing
Table-1, 5.1, 8.1 & 8.2(Phosphorous: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	9500	For complete testing
Table-1, 5.1, 8.1 & 8.2(Manganese: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	9500	For complete testing
Table-1, 5.1, 8.1 & 8.2(Silicon: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	9500	For complete testing
Table-1, 5.1, 8.1 & 8.2(Chromium: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	9500	For complete testing
Table-1, 5.1, 8.1 & 8.2(Molybdenum: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	9500	For complete testing
Table-1, 5.1, 8.1 & 8.2(Vanadium: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	9500	For complete testing
Table-1, 5.1, 8.1 & 8.2(Nickel: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	9500	For complete testing
Table-1, 5.1, 8.1 & 8.2(Copper: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	9500	For complete testing
Table-1, 5.1, 8.1 & 8.2(Aluminium: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	9500	For complete testing
Table-1, 5.1, 8.1 & 8.2(Nitrogen: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	9500	For complete testing
Table-1, 5.1, 8.1 & 8.2(Niobium: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	9500	For complete testing
Table-1, 5.1, 8.1 & 8.2(Titanium: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	9500	For complete testing
Table-1, 5.1, 8.1 & 8.2(Boron: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	9500	For complete testing
7(Freedom from defects)	-	9500	For complete testing
5 and 10.3.1(Tensile strength. IS 1608)	-	9500	For complete testing
5 and 10.3.1(Yield Stress. IS 1608)	-	9500	For complete testing
5 and 10.3.1(Percentage Elongation. . IS 1608)	-	9500	For complete testing
5 and 10.3.1(Internal Bend Diameter)	-	9500	For complete testing
11.3( Bend Test. IS 1599)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 2.1 of IS 808(Mass. IS 808)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 2.1 of IS 808(Sectional Area. IS 808)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 2.1 of IS 808(D)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 2.1 of IS 808(B)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 2.1 of IS 808(t)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 2.1 of IS 808(T)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 2.1 of IS 808(Flange Slop, Max α , )	-	9500	For complete testing
Cl 12 of IS 15911 and Table 2.1 of IS 808(R1)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 2.1 of IS 808(R2)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 2.1 of IS 808(Ix)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 2.1 of IS 808(Iy)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 2.1 of IS 808(rx)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 2.1 of IS 808(ry)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 2.1 of IS 808(Zx)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 2.1 of IS 808(Zy)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 2.2 of IS 808(Mass. IS 808)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 2.1 of IS 808(Sectional Area. IS 808)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 2.1 of IS 808(D)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 2.1 of IS 808(B)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 2.1 of IS 808(t)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 2.1 of IS 808(T)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 2.1 of IS 808(Flange Slop, Max α , )	-	9500	For complete testing
Cl 12 of IS 15911 and Table 2.1 of IS 808(R1)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 2.1 of IS 808(R2)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 2.1 of IS 808(Ix)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 2.1 of IS 808(Iy)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 2.1 of IS 808(rx)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 2.1 of IS 808(ry)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 2.1 of IS 808(Zx)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 2.1 of IS 808(Zy)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 3.1 of IS 808(Mass. IS 808)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 3.1 of IS 808(Sectional Area. IS 808)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 3.1 of IS 808(D)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 3.1 of IS 808(B)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 3.1 of IS 808(t)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 3.1 of IS 808(T)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 3.1 of IS 808(Flange Slop, Max α , )	-	9500	For complete testing
Cl 12 of IS 15911 and Table 3.1 of IS 808(R1)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 3.1 of IS 808(R2)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 3.1 of IS 808(Ix)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 3.1 of IS 808(Iy)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 3.1 of IS 808(rx)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 3.1 of IS 808(ry)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 3.1 of IS 808(Zx)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 3.1 of IS 808(Zy)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 4.1 of IS 808(Mass. IS 808)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 4.1 of IS 808(Sectional Area. IS 808)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 4.1 of IS 808(D)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 4.1 of IS 808(B)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 4.1 of IS 808(t)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 4.1 of IS 808(T)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 4.1 of IS 808(Flange Slop, Max α , )	-	9500	For complete testing
Cl 12 of IS 15911 and Table 4.1 of IS 808(R1)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 4.1 of IS 808(R2)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 4.1 of IS 808(Cy)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 4.1 of IS 808(Ix)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 4.1 of IS 808(Iy)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 4.1 of IS 808(rx)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 4.1 of IS 808(ry)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 4.1 of IS 808(Zx)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 4.1 of IS 808(Zy)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 5.1 of IS 808(Mass. IS 808)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 5.1 of IS 808(Sectional Area. IS 808)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 5.1 of IS 808(A*B)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 5.1 of IS 808(R1)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 5.1 of IS 808(R2)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 5.1 of IS 808(Cx)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 5.1 of IS 808(Cy)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 5.1 of IS 808(Ix)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 5.1 of IS 808(Iy)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 5.1 of IS 808(Ia( Max ))	-	9500	For complete testing
Cl 12 of IS 15911 and Table 5.1 of IS 808(Iv( Max ))	-	9500	For complete testing
Cl 12 of IS 15911 and Table 5.1 of IS 808(rx)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 5.1 of IS 808(ry)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 5.1 of IS 808(ru( Max ))	-	9500	For complete testing
Cl 12 of IS 15911 and Table 5.1 of IS 808(rv( Min ))	-	9500	For complete testing
Cl 12 of IS 15911 and Table 5.1 of IS 808(Zx)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 5.1 of IS 808(Zy )	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6.1 of IS 808(Mass. IS 808)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6.1 of IS 808(Sectional Area. IS 808)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6.1 of IS 808(A*B)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6.1 of IS 808(R1)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6.1 of IS 808(R2)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6.1 of IS 808(Cx)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6.1 of IS 808(Cy)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6.1 of IS 808(Tanα)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6.1 of IS 808(Ix)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6.1 of IS 808(Iy)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6.1 of IS 808(Ia( Max ))	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6.1 of IS 808(Iv( Max ))	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6.1 of IS 808(rx)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6.1 of IS 808(ry)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6.1 of IS 808(ru( Max ))	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6.1 of IS 808(rv( Min ))	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6.1 of IS 808(Zx)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6.1 of IS 808(Zy )	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6.2 of IS 808(Mass. IS 808)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6.2 of IS 808(Sectional Area. IS 808)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6.2 of IS 808(A*B)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6.2 of IS 808(R1)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6.2 of IS 808(R2)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6.2 of IS 808(Cx)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6.2 of IS 808(Cy)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6.2 of IS 808(Tanα)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6.2 of IS 808(Ix)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6.2 of IS 808(Iy)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6.2 of IS 808(Ia( Max ))	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6.2 of IS 808(Iv( Max ))	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6.2 of IS 808(rx)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6.2 of IS 808(ry)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6.2 of IS 808(ru( Max ))	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6.2 of IS 808(rv( Min ))	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6.2 of IS 808(Zx)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6.2 of IS 808(Zy )	-	9500	For complete testing
Cl 12 of IS 15911 and Table 1 of IS 1173(Clauses 3.1 , 5.1 and Table 1 of IS 1173)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 1 of IS 1252(Clauses 4.1 , 6.1 and Table 1 of IS 1252)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 2 of IS 1730(Clauses 4.1 , 4.2 and Table 1 of IS 1730)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 2 of IS 1730(Clauses 4.2 and Table 1 of IS 1730)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 3 of IS 1730(Clauses 4.3 and Table 1 of IS 1730)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 4 of IS 1730(Clauses 5.1 and Table 1 of IS 1730)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 5 of IS 1730(Clauses 5.2 and Table 1 of IS 1730)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 6 of IS 1730(Clauses 6.1 and Table 1 of IS 1730)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 7 of IS 1730(Clauses 6.2 and Table 1 of IS 1730)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 8 of IS 1730(Clauses 7.1, 7.2 and Table 1 of IS 1730)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 9 of IS 1730(Clauses 7.2 and Table 1 of IS 1730)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 1 of IS 1732(Clauses 3.1, 4.1,4.1.1 and Table 1 of IS 1732)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 2 of IS 1732(Clauses 3.1, 4.1,4.1.1 and Table 1 of IS 1732)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 1 of IS 1863(Clauses 4.1, 5.5 and Table 1 of IS 1863)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 2 of IS 1863(Clauses 5.1 and Table 2 of IS 1863)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 3 of IS 1863(Clauses 5.2 and Table 2 of IS 1863)	-	9500	For complete testing
Cl 12 of IS 15911 and Table 1 of IS 3954(Clauses 4, 6.1 and Table 2 of IS 3954)	-	9500	For complete testing
13(Tolerances)	-	9500	For complete testing
17(Marking)	-	9500	For complete testing
Table-1, 5.1, 8.1 & 8.2(Carbon: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	-	-
Table-1, 5.1, 8.1 & 8.2(Sulphur: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	-	-
Table-1, 5.1, 8.1 & 8.2(Phosphorous: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	-	-
Table-1, 5.1, 8.1 & 8.2(Manganese: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	-	-
Table-1, 5.1, 8.1 & 8.2(Silicon: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	-	-
Table-1, 5.1, 8.1 & 8.2(Chromium: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	-	-
Table-1, 5.1, 8.1 & 8.2(Molybdenum: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	-	-
Table-1, 5.1, 8.1 & 8.2(Vanadium: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	-	-
Table-1, 5.1, 8.1 & 8.2(Nickel: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	-	-
Table-1, 5.1, 8.1 & 8.2(Copper: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	-	-
Table-1, 5.1, 8.1 & 8.2(Aluminium: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	-	-
Table-1, 5.1, 8.1 & 8.2(Nitrogen: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	-	-
Table-1, 5.1, 8.1 & 8.2(Niobium: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	-	-
Table-1, 5.1, 8.1 & 8.2(Titanium: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	-	-
Table-1, 5.1, 8.1 & 8.2(Boron: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	-	-
7(Freedom from defects)	-	-	-
5 and 10.3.1(Tensile strength. IS 1608)	-	-	-
5 and 10.3.1(Yield Stress. IS 1608)	-	-	-
5 and 10.3.1(Percentage Elongation. . IS 1608)	-	-	-
5 and 10.3.1(Internal Bend Diameter)	-	-	-
11.3( Bend Test. IS 1599)	-	-	-
Cl 12 of IS 15911 and Table 2.1 of IS 808(Mass. IS 808)	-	-	-
Cl 12 of IS 15911 and Table 2.1 of IS 808(Sectional Area. IS 808)	-	-	-
Cl 12 of IS 15911 and Table 2.1 of IS 808(D)	-	-	-
Cl 12 of IS 15911 and Table 2.1 of IS 808(B)	-	-	-
Cl 12 of IS 15911 and Table 2.1 of IS 808(t)	-	-	-
Cl 12 of IS 15911 and Table 2.1 of IS 808(T)	-	-	-
Cl 12 of IS 15911 and Table 2.1 of IS 808(Flange Slop, Max α , )	-	-	-
Cl 12 of IS 15911 and Table 2.1 of IS 808(R1)	-	-	-
Cl 12 of IS 15911 and Table 2.1 of IS 808(R2)	-	-	-
Cl 12 of IS 15911 and Table 2.1 of IS 808(Ix)	-	-	-
Cl 12 of IS 15911 and Table 2.1 of IS 808(Iy)	-	-	-
Cl 12 of IS 15911 and Table 2.1 of IS 808(rx)	-	-	-
Cl 12 of IS 15911 and Table 2.1 of IS 808(ry)	-	-	-
Cl 12 of IS 15911 and Table 2.1 of IS 808(Zx)	-	-	-
Cl 12 of IS 15911 and Table 2.1 of IS 808(Zy)	-	-	-
Cl 12 of IS 15911 and Table 2.2 of IS 808(Mass. IS 808)	-	-	-
Cl 12 of IS 15911 and Table 2.1 of IS 808(Sectional Area. IS 808)	-	-	-
Cl 12 of IS 15911 and Table 2.1 of IS 808(D)	-	-	-
Cl 12 of IS 15911 and Table 2.1 of IS 808(B)	-	-	-
Cl 12 of IS 15911 and Table 2.1 of IS 808(t)	-	-	-
Cl 12 of IS 15911 and Table 2.1 of IS 808(T)	-	-	-
Cl 12 of IS 15911 and Table 2.1 of IS 808(Flange Slop, Max α , )	-	-	-
Cl 12 of IS 15911 and Table 2.1 of IS 808(R1)	-	-	-
Cl 12 of IS 15911 and Table 2.1 of IS 808(R2)	-	-	-
Cl 12 of IS 15911 and Table 2.1 of IS 808(Ix)	-	-	-
Cl 12 of IS 15911 and Table 2.1 of IS 808(Iy)	-	-	-
Cl 12 of IS 15911 and Table 2.1 of IS 808(rx)	-	-	-
Cl 12 of IS 15911 and Table 2.1 of IS 808(ry)	-	-	-
Cl 12 of IS 15911 and Table 2.1 of IS 808(Zx)	-	-	-
Cl 12 of IS 15911 and Table 2.1 of IS 808(Zy)	-	-	-
Cl 12 of IS 15911 and Table 3.1 of IS 808(Mass. IS 808)	-	-	-
Cl 12 of IS 15911 and Table 3.1 of IS 808(Sectional Area. IS 808)	-	-	-
Cl 12 of IS 15911 and Table 3.1 of IS 808(D)	-	-	-
Cl 12 of IS 15911 and Table 3.1 of IS 808(B)	-	-	-
Cl 12 of IS 15911 and Table 3.1 of IS 808(t)	-	-	-
Cl 12 of IS 15911 and Table 3.1 of IS 808(T)	-	-	-
Cl 12 of IS 15911 and Table 3.1 of IS 808(Flange Slop, Max α , )	-	-	-
Cl 12 of IS 15911 and Table 3.1 of IS 808(R1)	-	-	-
Cl 12 of IS 15911 and Table 3.1 of IS 808(R2)	-	-	-
Cl 12 of IS 15911 and Table 3.1 of IS 808(Ix)	-	-	-
Cl 12 of IS 15911 and Table 3.1 of IS 808(Iy)	-	-	-
Cl 12 of IS 15911 and Table 3.1 of IS 808(rx)	-	-	-
Cl 12 of IS 15911 and Table 3.1 of IS 808(ry)	-	-	-
Cl 12 of IS 15911 and Table 3.1 of IS 808(Zx)	-	-	-
Cl 12 of IS 15911 and Table 3.1 of IS 808(Zy)	-	-	-
Cl 12 of IS 15911 and Table 4.1 of IS 808(Mass. IS 808)	-	-	-
Cl 12 of IS 15911 and Table 4.1 of IS 808(Sectional Area. IS 808)	-	-	-
Cl 12 of IS 15911 and Table 4.1 of IS 808(D)	-	-	-
Cl 12 of IS 15911 and Table 4.1 of IS 808(B)	-	-	-
Cl 12 of IS 15911 and Table 4.1 of IS 808(t)	-	-	-
Cl 12 of IS 15911 and Table 4.1 of IS 808(T)	-	-	-
Cl 12 of IS 15911 and Table 4.1 of IS 808(Flange Slop, Max α , )	-	-	-
Cl 12 of IS 15911 and Table 4.1 of IS 808(R1)	-	-	-
Cl 12 of IS 15911 and Table 4.1 of IS 808(R2)	-	-	-
Cl 12 of IS 15911 and Table 4.1 of IS 808(Cy)	-	-	-
Cl 12 of IS 15911 and Table 4.1 of IS 808(Ix)	-	-	-
Cl 12 of IS 15911 and Table 4.1 of IS 808(Iy)	-	-	-
Cl 12 of IS 15911 and Table 4.1 of IS 808(rx)	-	-	-
Cl 12 of IS 15911 and Table 4.1 of IS 808(ry)	-	-	-
Cl 12 of IS 15911 and Table 4.1 of IS 808(Zx)	-	-	-
Cl 12 of IS 15911 and Table 4.1 of IS 808(Zy)	-	-	-
Cl 12 of IS 15911 and Table 5.1 of IS 808(Mass. IS 808)	-	-	-
Cl 12 of IS 15911 and Table 5.1 of IS 808(Sectional Area. IS 808)	-	-	-
Cl 12 of IS 15911 and Table 5.1 of IS 808(A*B)	-	-	-
Cl 12 of IS 15911 and Table 5.1 of IS 808(R1)	-	-	-
Cl 12 of IS 15911 and Table 5.1 of IS 808(R2)	-	-	-
Cl 12 of IS 15911 and Table 5.1 of IS 808(Cx)	-	-	-
Cl 12 of IS 15911 and Table 5.1 of IS 808(Cy)	-	-	-
Cl 12 of IS 15911 and Table 5.1 of IS 808(Ix)	-	-	-
Cl 12 of IS 15911 and Table 5.1 of IS 808(Iy)	-	-	-
Cl 12 of IS 15911 and Table 5.1 of IS 808(Ia( Max ))	-	-	-
Cl 12 of IS 15911 and Table 5.1 of IS 808(Iv( Max ))	-	-	-
Cl 12 of IS 15911 and Table 5.1 of IS 808(rx)	-	-	-
Cl 12 of IS 15911 and Table 5.1 of IS 808(ry)	-	-	-
Cl 12 of IS 15911 and Table 5.1 of IS 808(ru( Max ))	-	-	-
Cl 12 of IS 15911 and Table 5.1 of IS 808(rv( Min ))	-	-	-
Cl 12 of IS 15911 and Table 5.1 of IS 808(Zx)	-	-	-
Cl 12 of IS 15911 and Table 5.1 of IS 808(Zy )	-	-	-
Cl 12 of IS 15911 and Table 6.1 of IS 808(Mass. IS 808)	-	-	-
Cl 12 of IS 15911 and Table 6.1 of IS 808(Sectional Area. IS 808)	-	-	-
Cl 12 of IS 15911 and Table 6.1 of IS 808(A*B)	-	-	-
Cl 12 of IS 15911 and Table 6.1 of IS 808(R1)	-	-	-
Cl 12 of IS 15911 and Table 6.1 of IS 808(R2)	-	-	-
Cl 12 of IS 15911 and Table 6.1 of IS 808(Cx)	-	-	-
Cl 12 of IS 15911 and Table 6.1 of IS 808(Cy)	-	-	-
Cl 12 of IS 15911 and Table 6.1 of IS 808(Tanα)	-	-	-
Cl 12 of IS 15911 and Table 6.1 of IS 808(Ix)	-	-	-
Cl 12 of IS 15911 and Table 6.1 of IS 808(Iy)	-	-	-
Cl 12 of IS 15911 and Table 6.1 of IS 808(Ia( Max ))	-	-	-
Cl 12 of IS 15911 and Table 6.1 of IS 808(Iv( Max ))	-	-	-
Cl 12 of IS 15911 and Table 6.1 of IS 808(rx)	-	-	-
Cl 12 of IS 15911 and Table 6.1 of IS 808(ry)	-	-	-
Cl 12 of IS 15911 and Table 6.1 of IS 808(ru( Max ))	-	-	-
Cl 12 of IS 15911 and Table 6.1 of IS 808(rv( Min ))	-	-	-
Cl 12 of IS 15911 and Table 6.1 of IS 808(Zx)	-	-	-
Cl 12 of IS 15911 and Table 6.1 of IS 808(Zy )	-	-	-
Cl 12 of IS 15911 and Table 6.2 of IS 808(Mass. IS 808)	-	-	-
Cl 12 of IS 15911 and Table 6.2 of IS 808(Sectional Area. IS 808)	-	-	-
Cl 12 of IS 15911 and Table 6.2 of IS 808(A*B)	-	-	-
Cl 12 of IS 15911 and Table 6.2 of IS 808(R1)	-	-	-
Cl 12 of IS 15911 and Table 6.2 of IS 808(R2)	-	-	-
Cl 12 of IS 15911 and Table 6.2 of IS 808(Cx)	-	-	-
Cl 12 of IS 15911 and Table 6.2 of IS 808(Cy)	-	-	-
Cl 12 of IS 15911 and Table 6.2 of IS 808(Tanα)	-	-	-
Cl 12 of IS 15911 and Table 6.2 of IS 808(Ix)	-	-	-
Cl 12 of IS 15911 and Table 6.2 of IS 808(Iy)	-	-	-
Cl 12 of IS 15911 and Table 6.2 of IS 808(Ia( Max ))	-	-	-
Cl 12 of IS 15911 and Table 6.2 of IS 808(Iv( Max ))	-	-	-
Cl 12 of IS 15911 and Table 6.2 of IS 808(rx)	-	-	-
Cl 12 of IS 15911 and Table 6.2 of IS 808(ry)	-	-	-
Cl 12 of IS 15911 and Table 6.2 of IS 808(ru( Max ))	-	-	-
Cl 12 of IS 15911 and Table 6.2 of IS 808(rv( Min ))	-	-	-
Cl 12 of IS 15911 and Table 6.2 of IS 808(Zx)	-	-	-
Cl 12 of IS 15911 and Table 6.2 of IS 808(Zy )	-	-	-
Cl 12 of IS 15911 and Table 1 of IS 1173(Clauses 3.1 , 5.1 and Table 1 of IS 1173)	-	-	-
Cl 12 of IS 15911 and Table 1 of IS 1252(Clauses 4.1 , 6.1 and Table 1 of IS 1252)	-	-	-
Cl 12 of IS 15911 and Table 2 of IS 1730(Clauses 4.1 , 4.2 and Table 1 of IS 1730)	-	-	-
Cl 12 of IS 15911 and Table 2 of IS 1730(Clauses 4.2 and Table 1 of IS 1730)	-	-	-
Cl 12 of IS 15911 and Table 3 of IS 1730(Clauses 4.3 and Table 1 of IS 1730)	-	-	-
Cl 12 of IS 15911 and Table 4 of IS 1730(Clauses 5.1 and Table 1 of IS 1730)	-	-	-
Cl 12 of IS 15911 and Table 5 of IS 1730(Clauses 5.2 and Table 1 of IS 1730)	-	-	-
Cl 12 of IS 15911 and Table 6 of IS 1730(Clauses 6.1 and Table 1 of IS 1730)	-	-	-
Cl 12 of IS 15911 and Table 7 of IS 1730(Clauses 6.2 and Table 1 of IS 1730)	-	-	-
Cl 12 of IS 15911 and Table 8 of IS 1730(Clauses 7.1, 7.2 and Table 1 of IS 1730)	-	-	-
Cl 12 of IS 15911 and Table 9 of IS 1730(Clauses 7.2 and Table 1 of IS 1730)	-	-	-
Cl 12 of IS 15911 and Table 1 of IS 1732(Clauses 3.1, 4.1,4.1.1 and Table 1 of IS 1732)	-	-	-
Cl 12 of IS 15911 and Table 2 of IS 1732(Clauses 3.1, 4.1,4.1.1 and Table 1 of IS 1732)	-	-	-
Cl 12 of IS 15911 and Table 1 of IS 1863(Clauses 4.1, 5.5 and Table 1 of IS 1863)	-	-	-
Cl 12 of IS 15911 and Table 2 of IS 1863(Clauses 5.1 and Table 2 of IS 1863)	-	-	-
Cl 12 of IS 15911 and Table 3 of IS 1863(Clauses 5.2 and Table 2 of IS 1863)	-	-	-
Cl 12 of IS 15911 and Table 1 of IS 3954(Clauses 4, 6.1 and Table 2 of IS 3954)	-	-	-
13(Tolerances)	-	-	-
17(Marking)	-	-	-

-
Included w.e.f.21.05.2025

233

IS 1997 (2008)

Laboratory glassware - Burettes (Third Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11(Markings )	-	12000	For complete testing
5.1(Class of Accuracy)	-	12000	For complete testing
5.2(Types)	-	12000	For complete testing
6.1(Maximum permissible errors)	-	12000	For complete testing
8(Construction)	-	12000	For complete testing
Table 2(i) Scale length )	-	12000	For complete testing
Table 3( ii) Overall length )	-	12000	For complete testing
Table 4(iii) Distance of Zero line from top of burette )	-	12000	For complete testing
Table 5(iv) Distance of lowest graduation line from the top of stopcock )	-	12000	For complete testing
Table 6(v) Length of tube of uniform bore below graduation line )	-	12000	For complete testing
Table 7(vi) Distance of end of jet from underside of stopcock )	-	12000	For complete testing
8.2( c) Top of burette )	-	12000	For complete testing
8.3(d) Stopcock and similar devices)	-	12000	For complete testing
8.4(e) Stop Cock Leakage)	-	12000	For complete testing
8.5( f) Delivery jet)	-	12000	For complete testing
8.6(g) Delivery time )	-	12000	For complete testing
8.6(g) Delivery time )	-	12000	For complete testing
9(Graduations, figuring and patterns )	-	12000	For complete testing
9.1(a) Graduations patterns )	-	12000	For complete testing
9.2(Position of graduation line)	-	12000	For complete testing
9.3(c) Marking of graduation lines )	-	12000	For complete testing
12(. Visibility of graduation line)	-	12000	For complete testing
11(Markings )	-	12000	For complete testing
5.1(Class of Accuracy)	-	12000	For complete testing
5.2(Types)	-	12000	For complete testing
6.1(Maximum permissible errors)	-	12000	For complete testing
8(Construction)	-	12000	For complete testing
Table 2(i) Scale length )	-	12000	For complete testing
Table 3( ii) Overall length )	-	12000	For complete testing
Table 4(iii) Distance of Zero line from top of burette )	-	12000	For complete testing
Table 5(iv) Distance of lowest graduation line from the top of stopcock )	-	12000	For complete testing
Table 6(v) Length of tube of uniform bore below graduation line )	-	12000	For complete testing
Table 7(vi) Distance of end of jet from underside of stopcock )	-	12000	For complete testing
8.2( c) Top of burette )	-	12000	For complete testing
8.3(d) Stopcock and similar devices)	-	12000	For complete testing
8.4(e) Stop Cock Leakage)	-	12000	For complete testing
8.5( f) Delivery jet)	-	12000	For complete testing
8.6(g) Delivery time )	-	12000	For complete testing
8.6(g) Delivery time )	-	12000	For complete testing
9(Graduations, figuring and patterns )	-	12000	For complete testing
9.1(a) Graduations patterns )	-	12000	For complete testing
9.2(Position of graduation line)	-	12000	For complete testing
9.3(c) Marking of graduation lines )	-	12000	For complete testing
12(. Visibility of graduation line)	-	12000	For complete testing
11(Markings )	-	12000	For complete testing
5.1(Class of Accuracy)	-	12000	For complete testing
5.2(Types)	-	12000	For complete testing
6.1(Maximum permissible errors)	-	12000	For complete testing
8(Construction)	-	12000	For complete testing
Table 2(i) Scale length )	-	12000	For complete testing
Table 3( ii) Overall length )	-	12000	For complete testing
Table 4(iii) Distance of Zero line from top of burette )	-	12000	For complete testing
Table 5(iv) Distance of lowest graduation line from the top of stopcock )	-	12000	For complete testing
Table 6(v) Length of tube of uniform bore below graduation line )	-	12000	For complete testing
Table 7(vi) Distance of end of jet from underside of stopcock )	-	12000	For complete testing
8.2( c) Top of burette )	-	12000	For complete testing
8.3(d) Stopcock and similar devices)	-	12000	For complete testing
8.4(e) Stop Cock Leakage)	-	12000	For complete testing
8.5( f) Delivery jet)	-	12000	For complete testing
8.6(g) Delivery time )	-	12000	For complete testing
8.6(g) Delivery time )	-	12000	For complete testing
9(Graduations, figuring and patterns )	-	12000	For complete testing
9.1(a) Graduations patterns )	-	12000	For complete testing
9.2(Position of graduation line)	-	12000	For complete testing
9.3(c) Marking of graduation lines )	-	12000	For complete testing
12(. Visibility of graduation line)	-	12000	For complete testing
7(Material)	-	12000	For complete testing
11(Markings )	-	-	-
5.1(Class of Accuracy)	-	-	-
5.2(Types)	-	-	-
6.1(Maximum permissible errors)	-	-	-
8(Construction)	-	-	-
Table 2(i) Scale length )	-	-	-
Table 3( ii) Overall length )	-	-	-
Table 4(iii) Distance of Zero line from top of burette )	-	-	-
Table 5(iv) Distance of lowest graduation line from the top of stopcock )	-	-	-
Table 6(v) Length of tube of uniform bore below graduation line )	-	-	-
Table 7(vi) Distance of end of jet from underside of stopcock )	-	-	-
8.2( c) Top of burette )	-	-	-
8.3(d) Stopcock and similar devices)	-	-	-
8.4(e) Stop Cock Leakage)	-	-	-
8.5( f) Delivery jet)	-	-	-
8.6(g) Delivery time )	-	-	-
8.6(g) Delivery time )	-	-	-
9(Graduations, figuring and patterns )	-	-	-
9.1(a) Graduations patterns )	-	-	-
9.2(Position of graduation line)	-	-	-
9.3(c) Marking of graduation lines )	-	-	-
12(. Visibility of graduation line)	-	-	-
11(Markings )	-	-	-
5.1(Class of Accuracy)	-	-	-
5.2(Types)	-	-	-
6.1(Maximum permissible errors)	-	-	-
8(Construction)	-	-	-
Table 2(i) Scale length )	-	-	-
Table 3( ii) Overall length )	-	-	-
Table 4(iii) Distance of Zero line from top of burette )	-	-	-
Table 5(iv) Distance of lowest graduation line from the top of stopcock )	-	-	-
Table 6(v) Length of tube of uniform bore below graduation line )	-	-	-
Table 7(vi) Distance of end of jet from underside of stopcock )	-	-	-
8.2( c) Top of burette )	-	-	-
8.3(d) Stopcock and similar devices)	-	-	-
8.4(e) Stop Cock Leakage)	-	-	-
8.5( f) Delivery jet)	-	-	-
8.6(g) Delivery time )	-	-	-
8.6(g) Delivery time )	-	-	-
9(Graduations, figuring and patterns )	-	-	-
9.1(a) Graduations patterns )	-	-	-
9.2(Position of graduation line)	-	-	-
9.3(c) Marking of graduation lines )	-	-	-
12(. Visibility of graduation line)	-	-	-
11(Markings )	-	-	-
5.1(Class of Accuracy)	-	-	-
5.2(Types)	-	-	-
6.1(Maximum permissible errors)	-	-	-
8(Construction)	-	-	-
Table 2(i) Scale length )	-	-	-
Table 3( ii) Overall length )	-	-	-
Table 4(iii) Distance of Zero line from top of burette )	-	-	-
Table 5(iv) Distance of lowest graduation line from the top of stopcock )	-	-	-
Table 6(v) Length of tube of uniform bore below graduation line )	-	-	-
Table 7(vi) Distance of end of jet from underside of stopcock )	-	-	-
8.2( c) Top of burette )	-	-	-
8.3(d) Stopcock and similar devices)	-	-	-
8.4(e) Stop Cock Leakage)	-	-	-
8.5( f) Delivery jet)	-	-	-
8.6(g) Delivery time )	-	-	-
8.6(g) Delivery time )	-	-	-
9(Graduations, figuring and patterns )	-	-	-
9.1(a) Graduations patterns )	-	-	-
9.2(Position of graduation line)	-	-	-
9.3(c) Marking of graduation lines )	-	-	-
12(. Visibility of graduation line)	-	-	-
7(Material)	-	-	-

-
Included w.e.f 05.05.2025

234

IS 14276 (2016)

Cement bonded particle boards - Specification (First Revision)

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Finish)	-	14000	For complete testing
7(Dimensions and Tolerances)	-	14000	For complete testing
8.5(Workability)	-	14000	For complete testing
10.3, Table-1(Test for Density)	-	14000	For complete testing
10.5, Table-1(Test for Water Absorption)	-	14000	For complete testing
10.6, Table-1(Test for swelling in water)	-	14000	For complete testing
10.7, Table-1(Test for modulus of Rupture)	-	14000	For complete testing
10.8, Table-1(Test for modulus of Elasticity)	-	14000	For complete testing
10.9, Table-1(Test for tensile strength perpendicular to Surface)	-	14000	For complete testing
10.1, Table-1(Test for Screw Withdrawal Strength)	-	14000	For complete testing
Clause 8.2 Table 1(Moisture content)	-	14000	For complete testing

-
Included w.e.f 05.05.2025

235

IS 1239 : Part 1 (2004)

Steel Tubes, Tubulars and Other Wrought Steel Fittings : Part 1 Steel Tubes (BI-LINGUAL)

sizes upto and including 100 mm, Black and Galvanised

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
12 AND AS PER IS 4736(UNIFORMITY OF ZINC COATING)	-	500	For uniformity/ Mass of Zinc coating
12 AND AS PER IS 4736(MASS OF ZINC COATING)	-	500	For uniformity/ Mass of Zinc coating
6.2 AND AS PER IS 513(NITROGEN)	-	2000	For complete chemical analysis
6.2 AND AS PER IS 513(CARBON)	-	2000	For complete chemical analysis
6.2 AND AS PER IS 513(SILICON)	-	2000	For complete chemical analysis
6.2 AND AS PER IS 513(MANGANESE)	-	2000	For complete chemical analysis
6.2 AND AS PER IS 513(PHOSPHORUS)	-	2000	For complete chemical analysis
Cl. 15(Workmanship)	-	500	For complete workmanship
Cl. 14.3(Flattening test (Over 50 mm NB))	-	1500	For complete Cl 14
Cl. 14.2(Bend Test (uto and including 50 mm NB))	-	1500	For complete Cl 14
Cl. 14.1.1(Elongation)	-	3000	For complete Cl 14
Cl. 14.1(Tensile Strength)	-	3000	For complete Cl 14
Cl. 3.3, 10.2(Plain End)	-	500	For complete Cl 3 and Cl 10
Cl. 11(Length)	-	3000	For Complete Cl 8 , Cl 9 and Cl 11
Cl. 8, 9 Table 3,4 & 5(Mass of Tube)	-	3000	For Complete Cl 8 , Cl 9 and Cl 11
Cl. 6.5(Height of Internal Fin)	-	3000	For Complete Cl 8 , Cl 9 and Cl 11
Cl. 8, 9 Table 3,4 & 5(Thickness)	-	3000	For Complete Cl 8 , Cl 9 and Cl 11
Cl. 8 Table 3,4 & 5(Outside Diameter)	-	3000	For Complete Cl 8 , Cl 9 and Cl 11
Clause 14.1.1(Elongation Percent)	-	3000	For Complete Cl 14
Clause 11.3(Approximate Length)	-	3000	For Complete Cl 8 , Cl 9 and Cl 11
Clause 11.2(Exact Length)	-	3000	For Complete Cl 8 , Cl 9 and Cl 11
Clause 11.1(Random Length)	-	3000	For Complete Cl 8 , Cl 9 and Cl 11
Clause 8.1 (Table3,4,5)(Nominal Bore )	-	3000	For Complete Cl 8 , Cl 9 and Cl 11
Cl 15(Workmanship)	-	500	For Complete Cl 15
Cl 10.1.1(Manufacturing )	-	500	For Complete Cl 10
Cl 10.1(Manufacturing )	-	500	For Complete Cl 10
cl.17(MARKING)	-	500	For Complete Cl 17
6.2 AND AS PER IS 513(MICRO ALLOY)	-	2000	For Complete Chemical testing, if required
6.2 AND AS PER IS 10748(COPPER)	-	2000	For Complete Chemical testing, if required
6.2 AND AS PER IS 513(ALUMINIUM)	-	2000	For Complete Chemical testing, if required
6.2 AND AS PER IS 10748(NITROGEN)	-	2000	For Complete Chemical testing, if required
6.2 AND AS PER IS 10748(MICRO ALLOY)	-	2000	For Complete Chemical testing, if required
6.2 AND AS PER IS 10748(ALUMINIUM)	-	2000	For Complete Chemical testing, if required
6.2 AND AS PER IS 10748(SILICON)	-	2000	For Complete Chemical testing, if required
6.2 AND AS PER IS 10748(CARBON EQUIVALENT)	-	2000	For Complete Chemical testing, if required
6.2 AND AS PER IS 10748(MANGANESE)	-	2000	For Complete Chemical testing, if required
6.2 AND AS PER IS 10748(PHOSPHORUS)	-	2000	For Complete Chemical testing, if required
6.2 AND AS PER IS 10748(SULPHUR)	-	2000	For Complete Chemical testing, if required
6.2 AND AS PER IS 10748(CARBON)	-	2000	For Complete Chemical testing, if required
Clause - 6.1.1, Table-1( ALUMINIUM)	-	2000	For Complete Chemical testing, if required
Clause - 6.1.1, Table-1(SILICON)	-	2000	For Complete Chemical testing, if required
Clause - 6.1.1, Table-1(NITROGEN)	-	2000	For Complete Chemical testing, if required
Clause - 6.1.1, Table-1(MANGANESE)	-	2000	For Complete Chemical testing, if required
Clause - 6.1.1, Table-1(PHOSPHURS)	-	2000	For Complete Chemical testing, if required
Clause - 6.1.1, Table-1(SULPHUR)	-	2000	For Complete Chemical testing, if required
Clause - 6.1.1, Table-1( CARBON)	-	2000	For Complete Chemical testing, if required
Cl. 6.1.1, table1 of IS 1239(Part1)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	2000	For Complete Chemical testing, if required
Cl. 6.1.1, table1 of IS 1239(Part1)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	2000	For Complete Chemical testing, if required
Cl. 6.1.1, table1 of IS 1239(Part1)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	2000	For Complete Chemical testing, if required
Cl. 6.1.1, table1 of IS 1239(Part1)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	2000	For Complete Chemical testing, if required

-
-

236

IS 8931 (2021)

Copper alloy single taps, combination tap assemblies, stop valves and single lever mixers for water services Specification (second revision)

All types and all Sizes

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4(Classfication)	-	3500	For complete Cl. 4 and 6
Cl 4(Classfication)	-	3500	For complete Cl. 4 and 6
Cl 6.1(Manufacture,Workmanship & Construction)	-	3500	For complete Cl. 4 and 6
Cl 6.5(Manufacture,Workmanship & Construction)	-	3500	For complete Cl. 4 and 6
Cl 6.6(Manufacture,Workmanship & Construction)	-	3500	For complete Cl. 4 and 6
Cl 6.7(Manufacture,Workmanship & Construction)	-	3500	For complete Cl. 4 and 6
Cl 6.8(Manufacture,Workmanship & Construction)	-	3500	For complete Cl. 4 and 6
Cl 6.9(Manufacture,Workmanship & Construction)	-	3500	For complete Cl. 4 and 6
Cl 6.10(Manufacture,Workmanship & Construction)	-	3500	For complete Cl. 4 and 6
Cl 6.11(Manufacture,Workmanship & Construction)	-	3500	For complete Cl. 4 and 6
Cl 6.12(Manufacture,Workmanship & Construction)	-	3500	For complete Cl. 4 and 6
Cl 6.13(Manufacture,Workmanship & Construction)	-	3500	For complete Cl. 4 and 6
Cl 7(DIMENSIONS)	-	10000	For complete Cl. 4 and 6
Cl 7(DIMENSIONS)	-	10000	For complete Cl. 7
Cl 7(DIMENSIONS)	-	10000	For complete Cl. 7
Cl 7(DIMENSIONS)	-	10000	For complete Cl. 7
Cl 7(DIMENSIONS)	-	10000	For complete Cl. 7
Cl 8(ADDITIONAL REQUIREMENTS FOR ACCESSIBLE TAPS)	-	4500	Additional if required
Cl 10(PERFORMANCE REQUIREMENTS)	-	20000	For complete Cl. 10.except optional, if any
Cl 10(PERFORMANCE REQUIREMENTS)	-	20000	For complete Cl. 10.except optional, if any
Cl 10(PERFORMANCE REQUIREMENTS)	-	20000	For complete Cl. 10.except optional, if any
Cl 10(PERFORMANCE REQUIREMENTS)	-	20000	For complete Cl. 10.except optional, if any
Cl 10(PERFORMANCE REQUIREMENTS)	-	20000	For complete Cl. 10., except optional, if any
Cl 11(ADDITIONAL REQUIREMENTS FOR WATER EFFICIENCY)	-	15000	For complete Cl. 11
As per Table-1(Carbon)	-	4500	For complete chemical test (additional charges for extra elements, if required)
As per Table-1(Sulphur)	-	4500	For complete chemical test (additional charges for extra elements, if required)
As per Table-1(Phosphorus)	-	4500	For complete chemical test (additional charges for extra elements, if required)
As per Table-1(Manganese)	-	4500	For complete chemical test (additional charges for extra elements, if required)
As per Table-1(Nitrogen)	-	4500	For complete chemical test (additional charges for extra elements, if required)
As per Table-1(Silicon)	-	4500	For complete chemical test (additional if required)
As per Table-1(Aluminium)	-	4500	For complete chemical test (additional if required)
As per Table-1(Chromium)	-	4500	For complete chemical test (additional if required)
As per Table-1(Vanadium)	-	4500	For complete chemical test (additional if required)
As per Table-1(Molybdenum)	-	4500	For complete chemical test (additional if required)
As per Table-1(Iron)	-	4500	For complete chemical test (additional if required)
As per Table-1(Nickel)	-	4500	For complete chemical test (additional if required)
As per Table-1(Copper)	-	4500	For complete chemical test (additional if required)
As per Table-1(Zinc)	-	4500	For complete chemical test (additional if required)
As per Table-1(Lead)	-	4500	For complete chemical test ((additional charges for extra elements, if required)
As per Table-1(Boron)	-	4500	For complete chemical test (additional charges for extra elements, if required)

-
-

237

IS 15380 (2023)

MOULDED HIGH DENSITY FIBRE HDF PANELLED DOOR SHUTTERS - SPECIFICATION ( First Revision )

24100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.1(Sized)	-	24100	For complete testing
Cl-6.1.2(Moisture content in timbers)	-	24100	For complete testing
Cl-6.2 S.No (1), i(Density, kg/m3 , Min)	-	24100	For complete testing
Cl-6.2 S.No (1), ii(Moisture content, percent, Max)	-	24100	For complete testing
Cl-6.2 S.No (1), iii(Water absorption, percent, Max)	-	24100	For complete testing
Cl-6.2 S.No (1), iv(Swelling in water, percent, Max)	-	24100	For complete testing
Cl-6.2 S.No (1), v(Modulus of rupture, N/mm2 , Min)	-	24100	For complete testing
Cl-6.2 S.No (1), vi(Internal bond strength, N/mm2 , Min)	-	24100	For complete testing
Cl-6.2 S.No (1), vii(Immersion in boiling water at (100 ± 3) °C for 4 h)	-	24100	For complete testing
Cl-6.2 S.No (1), viii(Formaldehyde emission, mg/100 g, Max)	-	24100	For complete testing
Cl- 6.3(Particle Boards as Core)	-	24100	For complete testing
Cl- 6.4(Adhesive)	-	24100	For complete testing
Cl- 6.5(Laminated veneer lumber (LVL), veneer laminated lumber (VLL), Medium Density Fibre (MDF))	-	24100	For complete testing
Cl-11.1(Dimensions and Squareness Test)	-	24100	For complete testing
Cl-11.2(General Flatness Test)	-	24100	For complete testing
Cl-11.3(Local Planeness Test)	-	24100	For complete testing
Cl-11.4(Impact Indentation Test)	-	24100	For complete testing
Cl-11.5(Flexure Test)	-	24100	For complete testing
Cl-11.6(Edge Loading Test)	-	24100	For complete testing
Cl-11.7(Shock Resistance Test)	-	24100	For complete testing
Cl-11.8(Buckling Resistance Test)	-	24100	For complete testing
Cl-11.9(Slamming Test)	-	24100	For complete testing
Cl-11.10(Misuse Test)	-	24100	For complete testing
Cl-11.11(Varying Humidity Test)	-	24100	For complete testing
Cl-11.12(End Immersion Test)	-	24100	For complete testing
Cl-11.13(Glue Adhesion Test)	-	24100	For complete testing
Cl-11.14(Screw Withdrawal Resistance Test)	-	24100	For complete testing
Cl-12.2(Sample Size)	-	24100	For complete testing
Cl-14(Marking)	-	24100	For complete testing
Cl-6.1.1(Bulk density of timber)	-	24100	For complete testing
Cl-9(Workmanship and finish)	-	24100	For complete testing

-
Included w.e.f 05.05.2025

238

IS 1786 (2008)

High strength deformed steel bars and wires for concretere inforcement - Specification (Fourth Revision)

For all sizes and Grades as per IS 1786

10800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 6.1(Length, Width & Thickness)	-	3000	For Cl 6 & 7 testing charges
Cl 7.2(Weight)	-	3000	For Cl 6 & 7 testing charges
Cl 5(Deformations and Surface Characteristics)	-	2000	For Complete Cl 5
Cl 8.1(UTM)	-	3000	For Cl 8 & 9 testing charges, , For Pull out - 8500
Cl 9.3(Load In One Direction)	-	3000	For Cl 8 & 9 testing charges
Cl 9.4(Load In Other Direction From Bend)	-	3000	For Cl 8 & 9 testing charges
Cl. 8.1 Table 3(Elongation, percentage)	-	3000	For Cl 8 & 9 testing charges
Cl. 8.1 Table 3(TS/YS ratio)	-	3000	For Cl 8 & 9 testing charges
Cl. 8.1 Table 3(Tensile Strength (TS))	-	3000	For Cl 8 & 9 testing charges
Cl. 8.1 Table 3(Yield Stress (YS))	-	3000	For Cl 8 & 9 testing charges
Cl. 7.2 Table -2 (Nominal Mass)	-	3000	For Cl 6 & 7 testing charges
Cl. 6.1(Nominal Size)	-	3000	For Cl 6 & 7 testing charges
Cl. 5 (Cl. 5 - Mean projected area of transverse ribs (1/3 of Ar))	-	2000	For Complete Cl 5
4.1(Sulphur and phosphorous)	-	2800	For Complete Chemical Testing, if required
4.1(CE)	-	2800	For Complete Chemical Testing, if required
4.1( Nitrogen%)	-	2800	For Complete Chemical Testing, if required
4.1(Ni)	-	2800	For Complete Chemical Testing, if required
4.1(Mo)	-	2800	For Complete Chemical Testing, if required
4.1(Cr)	-	2800	For Complete Chemical Testing, if required
4.1( Ti)	-	2800	For Complete Chemical Testing, if required
4.1(V)	-	2800	For Complete Chemical Testing, if required
4.1( Nb)	-	2800	For Complete Chemical Testing, if required
4.1( Aluminium %)	-	2800	For Complete Chemical Testing, if required
4.1( Copper %)	-	2800	For Complete Chemical Testing, if required
4.1(Silicon %)	-	2800	For Complete Chemical Testing, if required
4.1(Sulphur %)	-	2800	For Complete Chemical Testing, if required
4.1(Manganese %)	-	2800	For Complete Chemical Testing, if required
4.1(Carbon %)	-	2800	For Complete Chemical Testing, if required
Cl. 5 (Cl.5 Mean area of ribs/unit length (Ar), )	-	2000	For Complete Cl 5
Cl. 8.1 Table 3(Total Elongation at Maximum Force)	-	3000	For Complete Cl 8 and Cl 9
5.7(PullOut (Bond Test))	-	11800	For Pull out test
Cl. 5.7(Average compressive strength of cubes at 28 days)	-	11800	For Pull out test
Cl. 5.7(Bond Strength at 0.25 mm slip)	-	11800	For Pull out test
Cl. 5.7(Date of testing of concrete cubes)	-	11800	For Pull out test
Cl. 5.7(Date of casting of concrete cubes)	-	11800	For Pull out test
5.7(Pull-out test - IS:2770(P1))	-	11800	For Pull out test

-
-

239

IS 447 (1988)

Specification for rubber hose for welding (Fourth Revision)

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Classification - IS 444)	-	8000	For complete testing
5(Lining - IS 444)	-	8000	For complete testing
5(Reinforcement - IS 444)	-	8000	For complete testing
5(Cover - IS 444)	-	8000	For complete testing
5(Lining and Cover - IS 444)	-	8000	For complete testing
6.1- Table 1(Internal diameters - ISO 4671)	-	8000	For complete testing
6.2(Concentricity - ISO 4671)	-	8000	For complete testing
6.3(Length -IS 4671)	-	8000	For complete testing
6.4( thickness of the lining plus cover - ISO 4671)	-	8000	For complete testing
6.4(If the cover is fluted, the depth of the flutes - ISO 4671)	-	8000	For complete testing
7.1 - Table 2( tensile strength of Lining - ISO 37 )	-	8000	For complete testing
7.1 - Table 2( tensile strength of Cover - ISO 37 )	-	8000	For complete testing
7.1 - Table 2(elongation at break of Lining - ISO 37)	-	8000	For complete testing
7.1 - Table 2(elongation at break of Cover - ISO 37)	-	8000	For complete testing
7.1 - Table 2(Change in tensile strength of Lining from original value after ageing(max) - ISO 188 and ISO 37)	-	8000	For complete testing
7.1 - Table 2(Change in tensile strength of Cover from original value after ageing(max) - ISO 188 and ISO 37)	-	8000	For complete testing
7.1 - Table 2(Change in elongation at break of Lining from original value after ageing (max.) - ISO 188 and ISO 37)	-	8000	For complete testing
7.1 - Table 2(Change in elongation at break of Cover from original value after ageing (max.) - ISO 188 and ISO 37)	-	8000	For complete testing
7.2 - Table 3(Proof pressure at 23 °C - ISO 1402)	-	8000	For complete testing
7.2 - Table 3(Change in length at proof pressure - ISO 1402)	-	8000	For complete testing
7.2 - Table 3(Minimum burst pressure - ISO 1402)	-	8000	For complete testing
7.2 - Table 3(Adhesion between components - ISO 8033)	-	8000	For complete testing
7.2 - Table 3(Ozone resistance - ISO 7326)	-	8000	For complete testing
7.2 - Table 3(Flexibility at 23 °C - Method A of ISO 1746)	-	8000	For complete testing
7.2 - Table 3(Low-temperature flexibility - Method B of ISO 4672)	-	8000	For complete testing
Cl. 3.2 - Table 1(Bore size)	-	8000	For complete testing
Cl. 3.2 - Table 1(Lining Thickness)	-	8000	For complete testing
Cl. 3.2 - Table 1(Cover Thickness)	-	8000	For complete testing
Cl. 3.2 - Table 1(Length %)	-	8000	For complete testing
Cl. 3.3 - Table 2(Tensile strength - Lining MPA)	-	8000	For complete testing
Cl. 3.3 - Table 2(Tensile strength - Cover Mpa)	-	8000	For complete testing
Cl. 3.3 - Table 2(Elongation at break - Lining %)	-	8000	For complete testing
Cl. 3.3 - Table 2(Elongation at break - Cover %)	-	8000	For complete testing
Cl. 3.3 - Table 2(After Ageing Tensile strength - Lining %)	-	8000	For complete testing
Cl. 3.3 - Table 2(After Ageing Tensile strength - Cover %)	-	8000	For complete testing
Cl. 3.3 - Table 2(After Ageing Elongation at break - Lining %)	-	8000	For complete testing
Cl. 3.3 - Table 2(After Ageing Elongation at break - Cover %)	-	8000	For complete testing
Cl. 3.4 - Table3(Pressure Tests)	-	8000	For complete testing
Cl. 3.4 - Table3(Adhesion KN/m Min)	-	8000	For complete testing
Cl. 3.2 - Table 1(Bore size, mm)	-	8000	For complete testing
Cl. 3.2 - Table 1(Lining Thickness, mm)	-	8000	For complete testing
Cl. 3.2 - Table 1(Cover Thickness, mm)	-	8000	For complete testing
Cl. 3.2 - Table 1(Length)	-	8000	For complete testing
Cl. 3.3 - Table 2(Tensile strength - Lining, Mpa)	-	8000	For complete testing
Cl. 3.3 - Table 2(Tensile strength - Cover, Mpa)	-	8000	For complete testing
Cl. 3.3 - Table 2(Elongation at break - Lining)	-	8000	For complete testing
Cl. 3.3 - Table 2(Elongation at break - Cover)	-	8000	For complete testing
Cl. 3.3 - Table 2(After Ageing Tensile strength - Lining)	-	8000	For complete testing
Cl. 3.3 - Table 2(After Ageing Tensile strength - Cover)	-	8000	For complete testing
Cl. 3.3 - Table 2(After Ageing Elongation at break - Lining)	-	8000	For complete testing
Cl. 3.3 - Table 2(After Ageing Elongation at break - Cover)	-	8000	For complete testing
Cl. 3.4 - Table3(Pressure Tests)	-	8000	For complete testing
Cl. 3.4 - Table3(Adhesion, KN/m Min)	-	8000	For complete testing
Cl. 3.4 - Table3(Adhesion)	-	8000	For complete testing
Cl. 3.4 - Table3(Pressure Tests)	-	8000	For complete testing
Cl. 3.3 - Table 2(After Ageing Elongation at break - Cover)	-	8000	For complete testing
Cl. 3.3 - Table 2(After Ageing Elongation at break - Lining)	-	8000	For complete testing
Cl. 3.3 - Table 2(After Ageing Tensile strength - Cover)	-	8000	For complete testing
Cl. 3.3 - Table 2(After Ageing Tensile strength - Lining)	-	8000	For complete testing
Cl. 3.3 - Table 2(Elongation at break - Cover)	-	8000	For complete testing
Cl. 3.3 - Table 2(Elongation at break - Lining)	-	8000	For complete testing
Cl. 3.3 - Table 2(Tensile strength - Cover)	-	8000	For complete testing
Cl. 3.3 - Table 2(Tensile strength - Lining)	-	8000	For complete testing
Cl. 3.2 - Table 1(Length)	-	8000	For complete testing
Cl. 3.2 - Table 1(Lining Thickness)	-	8000	For complete testing
Cl. 3.2 - Table 1(Bore size)	-	8000	For complete testing
Cl. 3.2 - Table 1(Cover Thickness)	-	8000	For complete testing

-
Included w.e.f.16.07.2025

240

IS 14364 (2024)

Quaternary Ammonium Compound Based Surface Cleaner, Liquid ï¿½ Specification ( First Revision )

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(Description)	-	25000	For complete testing
Cl-4.2(Composition)	-	25000	For complete testing
Cl-4.3(Odour)	-	25000	For complete testing
Cl-4.4(Colour)	-	25000	For complete testing
Cl-4.5(Stability on Dilution)	-	25000	For complete testing
Cl-4.6(Cleaning Property)	-	25000	For complete testing
Cl-4.7(Applicability)	-	25000	For complete testing
Cl-4.8(Keeping Quality)	-	25000	For complete testing
Cl-4.8 & 4.9, Table-1 (i)(Total non-volatile matter, percent by mass, Min)	-	25000	For complete testing
Cl-4.8 & 4.9, Table-1 (ii)(pH)	-	25000	For complete testing
Cl-4.8 & 4.9, Table-1 (iii)(QAC content, percent by mass, Min)	-	25000	For complete testing
Cl-6(Marking)	-	25000	For complete testing
Cl-4.1(Description)	-	-	-
Cl-4.2(Composition)	-	-	-
Cl-4.3(Odour)	-	-	-
Cl-4.4(Colour)	-	-	-
Cl-4.5(Stability on Dilution)	-	-	-
Cl-4.6(Cleaning Property)	-	-	-
Cl-4.7(Applicability)	-	-	-
Cl-4.8(Keeping Quality)	-	-	-
Cl-4.8 & 4.9, Table-1 (i)(Total non-volatile matter, percent by mass, Min)	-	-	-
Cl-4.8 & 4.9, Table-1 (ii)(pH)	-	-	-
Cl-4.8 & 4.9, Table-1 (iii)(QAC content, percent by mass, Min)	-	-	-
Cl-6(Marking)	-	-	-

-
Included w.e.f.21.05.2025

Bureau of Indian Standards

The National Standards Body of India

JBS TESTING SOLUTIONS PVT LTD (27), JALANDHAR

PLOT NO. 27, STREET NO. 2, ADJOINING FOCAL POINT ROAD, TRANSPORT NAGAR, JALANDHAR, PUNJAB, JALANDHAR, Jalandhar, Punjab, 144004

9988862929 jbstestingsolutions@gmail.com

Scope List