BIS - LIMS (Laboratory Information Management System)

BIS, Northern Regional Laboratory (NRL)

B-69, Industrial Focal Point, Phase VII, Mohali, Mohali, S.A.S Nagar, Punjab, 160059

- nrol@bis.gov.in

Scope List

Reset

296 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

151

IS 8794 (1988)

Specification for cast iron detachable joints for use with asbestos cement pressure pipes (First Revision)

3900/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1, Table 2 (External Dia of AC Pipe(D2))	-
6.1, Table 2 (Inside diaFlange(DI))	-
6.1, Table 2 (External Dia at Centre(DEC))	-
6.1, Table 2 (Thickness(t))	-
6.1, Table 3 (Nominal Dia of Bolt(do))	-
6.1, Table 3 (Minimum prefared length of bolt(L))	-
6.1, Table 4 (Mass of joints)	-
8.4 (Coating)	-

-
HST for size above 300 mm, Facility for Chemical tests not available

152

IS 1166 (1986)

Specification for condensed milk, partly skimmed and skimmed condensed milk (Second Revision)

10430 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Table 1 (i) (Apendix B) (Total milk solids - Partly Skimmed Condenied Milk)	-
Table 1 (ii) (IS : 11762- 1986) (Fat -Condensed Milk)	-
Table 1 (iii) (Apendix C) (Sucrose -Condensed Milk)	-
Table 1 (vi) (Apendix D) (Titratable acidity (as lactic acid) -Condensed Milk)	-
Table 1 (v) (Apendix E) (Accelerated starage test -Condensed Milk)	-
Cl.5.1.10.1 (Salmonella IS 5887 Part 3)	-
Cl.5.1.10.1 (Shigella IS 5887 Part 7)	-
Cl.5.1.10.2 (Coliform Count IS 5401 Part 1)	-
Cl.5.1.10.3 (Yeast and Mould Count IS 5403)	-
Cl.5.1.10.4 (Coagulase positive Staphylococcus aureus IS 5887 Part 2)	-
Cl.5.1.10.5 (Escherichia coli IS 5887 Part 1)	-

-
Microbiological testing is complete. Excluding Except Lactate Crystals

153

IS 2082 (2018)

Stationary storage type electric water heaters - Specification (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 (Classification )	-
6 (Classification )	-
7 (Marking)	-
7 (Marking)	-
7 (Marking)	-
7 (Marking)	-
7 (Marking)	-
7 (Marking)	-
7 (Marking)	-
7 (Marking)	-
7 (Marking)	-
7 (Marking)	-
7 (Marking)	-
7 (Marking)	-
7 (Marking)	-
7 (Marking)	-
7 (Marking)	-
7 (Marking)	-
7 (Marking)	-
7 (Marking)	-
7 (Marking)	-
7 (Marking)	-
7 (Marking)	-
7 (Marking)	-
7 (Marking)	-
7 (Marking)	-
7 (Marking)	-
7 (Marking)	-
7 (Marking)	-
(Cl.8 of IS 302-2-21:2011) (Protection Against Access to Live Parts)	-
(Cl.10 of IS 302-2-21: 2011) (Power Input & Current)	-
(Cl.11 of 302-2-21:2011) (Heating)	-
(Cl.11 of 302-2-21:2011) (Heating)	-
(Cl.13 of IS 302-2-21:2011) (Leakage Current )	-
(Cl.15 of IS 302-2-21-2011) (Moisture Resistance)	-
(Cl.15 of IS 302-2-21-2011) (Moisture Resistance)	-
(Cl.15 of IS 302-2-21-2011) (Moisture Resistance)	-
(Cl.19 of IS 302-2-21:2011) (Abnormal Operation)	-
(Cl.19 of IS 302-2-21:2011) (Abnormal Operation)	-
(Cl.19 of IS 302-2-21:2011) (Abnormal Operation)	-
(Cl.19 of IS 302-2-21:2011) (Abnormal Operation)	-
(Cl.20 of IS 302-2-21:2011) (Stability & Mechanical Hazards)	-
(Cl.21ofIS302-2-21:2011) (Mechanical strength)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl.22 Of IS 302-2-21:2011) (Construction)	-
(Cl. 23 of IS 302-2-21: 2011) (Internal Wiring )	-
(Cl. 23 of IS 302-2-21: 2011) (Internal Wiring )	-
(Cl. 23 of IS 302-2-21: 2011) (Internal Wiring )	-
(Cl. 23 of IS 302-2-21: 2011) (Internal Wiring )	-
(Cl. 23 of IS 302-2-21: 2011) (Internal Wiring )	-
(Cl. 23 of IS 302-2-21: 2011) (Internal Wiring )	-
(Cl. 23 of IS 302-2-21: 2011) (Internal Wiring )	-
(Cl. 23 of IS 302-2-21: 2011) (Internal Wiring )	-
(Cl. 23 of IS 302-2-21: 2011) (Internal Wiring )	-
(Cl. 23 of IS 302-2-21: 2011) (Internal Wiring )	-
(Cl.24ofIS302-221:2011) (Component)	-
(Cl.24ofIS302-221:2011) (Component)	-
(Cl. 23 of IS 302-2-21: 2011) (Internal Wiring )	-
(Cl.24ofIS302-221:2011) (Component)	-
(Cl.24ofIS302-221:2011) (Component)	-
(Cl.24ofIS302-221:2011) (Component)	-
(Cl.25 of IS 302-2-21:2011) (Supply Connection & External Flexible Cords)	-
(Cl.25 of IS 302-2-21:2011) (Supply Connection & External Flexible Cords)	-
(Cl.25 of IS 302-2-21:2011) (Supply Connection & External Flexible Cords)	-
(Cl.25 of IS 302-2-21:2011) (Supply Connection & External Flexible Cords)	-
(Cl.25 of IS 302-2-21:2011) (Supply Connection & External Flexible Cords)	-
(Cl.25 of IS 302-2-21:2011) (Supply Connection & External Flexible Cords)	-
(Cl.25 of IS 302-2-21:2011) (Supply Connection & External Flexible Cords)	-
(Cl.25 of IS 302-2-21:2011) (Supply Connection & External Flexible Cords)	-
(Cl.25 of IS 302-2-21:2011) (Supply Connection & External Flexible Cords)	-
(Cl.25 of IS 302-2-21:2011) (Supply Connection & External Flexible Cords)	-
(Cl.25 of IS 302-2-21:2011) (Supply Connection & External Flexible Cords)	-
(Cl.25 of IS 302-2-21:2011) (Supply Connection & External Flexible Cords)	-
(Cl.25 of IS 302-2-21:2011) (Supply Connection & External Flexible Cords)	-
(Cl.25 of IS 302-2-21:2011) (Supply Connection & External Flexible Cords)	-
(Cl.25 of IS 302-2-21:2011) (Supply Connection & External Flexible Cords)	-
(Cl.25 of IS 302-2-21:2011) (Supply Connection & External Flexible Cords)	-
(Cl.26 of IS 302-2-21: 2011) (Terminals for External Conductors)	-
(Cl.26 of IS 302-2-21: 2011) (Terminals for External Conductors)	-
(Cl.26 of IS 302-2-21: 2011) (Terminals for External Conductors)	-
(Cl.26 of IS 302-2-21: 2011) (Terminals for External Conductors)	-
(Cl.26 of IS 302-2-21: 2011) (Terminals for External Conductors)	-
(Cl.26 of IS 302-2-21: 2011) (Terminals for External Conductors)	-
(Cl.26 of IS 302-2-21: 2011) (Terminals for External Conductors)	-
(Cl.26 of IS 302-2-21: 2011) (Terminals for External Conductors)	-
(Cl.26 of IS 302-2-21: 2011) (Terminals for External Conductors)	-
(Cl.26 of IS 302-2-21: 2011) (Terminals for External Conductors)	-
(Cl.27 of IS 302-2-21:2011) (Provision for Earthing)	-
(Cl.27 of IS 302-2-21:2011) (Provision for Earthing)	-
(Cl.27 of IS 302-2-21:2011) (Provision for Earthing)	-
(Cl.27 of IS 302-2-21:2011) (Provision for Earthing)	-
(Cl.27 of IS 302-2-21:2011) (Provision for Earthing)	-
(Cl.27 of IS 302-2-21:2011) (Provision for Earthing)	-
(Cl.28 of IS 302-2-21:2011) (Screws & Connections)	-
(Cl.29ofIS302-2-21:2011) (Clearances, Creepage Distances and Solid Insulation)	-
(Cl.30 of IS 302-2-21:2011) (Resistance to Heat & Fire)	-
(Cl.30 of IS 302-2-21:2011) (Resistance to Heat & Fire)	-
(Cl.31 of IS 302-2-21:2011) (Resistance to Rusting)	-
(Cl.15 of IS 2082:2018) (Verification of the Rated Capacity)	-
(Cl.16 of IS 2082:2018) (Standing Loss per 24 Hours)	-
(Cl.17 of IS 2082:2018) (Hot Water Output)	-
(Cl.18 of IS 2082:2018) ( Reheating Time)	-
(Cl.19 of IS 2082:2018) (Mixing Factor)	-
(Cl.20 of IS 2082:2018) (Deviation of Dial Calibration)	-
(Cl.21 of IS 2082:2018) (Cyclic Temperature Variation)	-
(Cl.22 of IS 2082:2018) (Finish)	-

-
Excluding Cl.24.102.1 and Cl.24.102.2 Electronic circuit and Software evaluation Cl. 19.11 and Cl. 19.12 abnormal test (for Electronic circuit)

154

IS 8462 (1977)

Specification for sterilizer, portable, vertical, pressure type

For sterilizers with painted steel stand Rs.9580/-. For View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Shape and Dimensions)	-
4.2 (Thickness)	-
5.8 (Construction)	-
6.1 (Workmanship and Finish)	-
6.2 (Workmanship and Finish)	-
8.1 (Proof Pressure Test)	-

-
Mechanical: Test facility is complete, Facility for chemical test is not available

155

IS 8329 (2000)

Centrifugally cast (Spun) ductile iron pressure pipes for water, gas and sewage - Specification (Third Revision)

Rs.7800/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 10 (Hardness & Tensile Test)	-
Cl 11 (Hydrostatic Test)	-
Cl 13 (Length, Diameter, Wall Thickness & Ovality)	-

-
Excluding HST for size above 300 mm

156

IS 6240 (2008)

Hot rolled steel plate (Up To 6 Mm) sheet and strip for the manufacture of low pressure liquefiable gas cylinders (Fourth Revision)

9710 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 7 (UTM)	-
Cl 8 (Press)	-
Cl 9 (Strainage Embrittlement)	-
Cl 13 (Length, Width & Thickness)	-
6.1 (Carbon %)	-
6.1 (Manganese %)	-
6.1 (Phosphorus %)	-
6.1 (Sulphur %)	-
6.1 (Silicon %)	-
6.1 (Nitrogen%)	-

-
Excluding, Cupping Test, Microalloying elements

157

IS 814 (2004)

Covered electrodes for manual metal arc welding of carbon and carbon manganese steel - Specification (Sixth Revision)

Rs. 17500/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1.1 (Diameter of Core Wire)	-
7.1.2 (Length of Electrodes)	-
7.2.1 (Contact End)	-
7.2.2 (Arc striking End)	-
7.3 (Concentricity of Flux covering with core wire)	-
9.1.2 Table 6 (Ultimate Tensile Strength-Annex F)	-
9.1.2 Table 6 ( Yield Stress -Annex F)	-
9.1.2 Table 6 (Percentage Elongation on Gauge Length-Annex F)	-
9.2 (Butt Weld Bend Test-IS 1599)	-
6 & 8.2 (Carbon- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
6 & 8.2 (Sulphur- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
6 & 8.2 (Silicon- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
6 & 8.2 (Manganese- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
6 & 8.2 (Phosphorous- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
6 & 8.2 (Copper- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
6 & 8.2 (Vanadium- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
6 & 8.2 (Titanium- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
6 & 8.2 (Alumiminium- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
6 & 8.2 (Cr+Ni+Mo - Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
6 & 8.2 (Chromium- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
6 & 8.2 (Nickel- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
6 & 8.2 (Molybdenum- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
6 & 8.2 (Mn+Ni+Cr+Mo+V - Relevant Parts of IS 228 or any other established instrumental/chemical method)	-

-
Radiographic test, increased metal recovery, diffusible hydrogen evaluation and For tensile and bend test prepared test pieces are required. Complete testing facility for Cl. 6 is available. Test Facility as per Cl. 8.2 is not available

158

IS 2061 (1995)

Bicycle - Front forks - Specification (First Revision)

Rs. 2727/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8 (MARKING)	-
3 (Material)	-
4 (Dimensions)	-
5 (. Manufacturer&Finish)	-
7.1.1 ( i) Load test )	-
7.1.2 (ii) Expansion Tes )	-
7.1.3 (iii) Tests for Finish)	-
7.1.4 (iv) Impact Test)	-
7.1.3 (iii) Tests for Finish)	-

-
Mechanical: Test facility is complete, Chemical: Excluding Microalloying elements

159

IS 7887 (1992)

Mild steel wire rod for general engineering purposes - Specification (First Revision)

Rs.7200/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (Workmanship)	-
Cl 9 (Nominal Diameter & Out Of Shape)	-
6.1 (Carbon %)	-
6.1 (Manganese %)	-
6.1 (Phosphorus %)	-
6.1 (Sulphur %)	-
6.1 (Silicon %)	-

-
Mechanical-Complete Excluding Microalloying Elements, Copper

160

IS 13334 : Part 2 (2014)

Skimmed milk powder - Specification: Part 2 extra grade (First Revision)

Rs 10430/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Table 1 (i) (Moisture (IS 116231or 16072))	-
Table 1 (v) (Total ash (on dry basis), Annex B of IS 14433)	-
Table 1 (iv) (Insolubility index (IS 12759))	-
Table 1 (vi) (Titratable acidity (IS 11766))	-
Table 1 (iv) (Insolubility index (IS 12759))	-
Table 1 (vi) (Titratable acidity (IS 11766))	-
Table 1 (iv) (Insolubility index (IS 12759))	-
Table 1 (vi) (Titratable acidity (IS 11766))	-
Table 1 (iii) (Milk fat (IS 117213) or Annex B)	-
Table 1 (viii) (Scorched particles (equivalent to Disc B) (IS 13500))	-
Table 1 (ix) (Bacterial count (IS 5402))	-
Table 1 (x) (Coliform count (IS 5401 - Part 1))	-
Table 1 (xi) (Escherichia coli (IS 5887 - Part 1))	-
Table 1 (xii) (Coagulase positive Staphylococcus aureus (IS 5887 - Part 2))	-
Table 1 (xiii) (Salmonella (IS 5887 - Part 3))	-
Table 1 (xiv)(a) (Spore Count: a) Aerobic (Bacillus cereus) Type M (IS 5887 - Part 6))	-
Table 1 (xiv)(b) (Spore Count: b) Anaerobic (Sulfite reducing Clostridia) Type m (ISO 15213 : 2003))	-
Table 1 (xv) (Listeria monocytogenes (IS 14988 - Part 2 : 2001))	-

-
Microbiological testing is complete. Excluding Lactate Content

161

IS 784 (2019)

Prestressed concrete pipes (Including Specials) - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8.4 (Circumferential Prestressing)	-

-
Certification Scheme is being operated on FT basis Excluding only compression strength can be done

162

IS 7834 : Part 1 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 1 General requirements

Rs.2400/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.4 (Minimum Thickness)	-
Cl. 5.1.1, 5.1.2, Table 1, Fig 1 (Minimum Socket Length)	-
Cl. 5.1.1, 5.1.2, Table 1, Fig 1 (Mean Socket Internal Diameter at Mid-Point of Socket Length)	-
Cl. 5.1.1, 5.1.2, Table 1, Fig 1 (Out-of-roundness tolerances of socket inside diameter)	-
Cl. 6.1 (Stress Relief Test- Appendix A)	-
Cl. 6.4 (Short-Term Hydraulic Test- Appendix D)	-

-
Excluding Performance requirements

163

IS 7466 (1994)

Rubber gaskets for pressure cookers - Specifications (First Revison)

Rs.9480/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2 (Workmanship and Finish )	-
3.4-Table 1(ii) (Requirements of Rubber Used for Gaskets-Tensile strength,)	-
3.4-Table 1(iii) (Requirements of Rubber Used for Gaskets-Elongation at break)	-
3.4-Table 1(iv-b) (Requirements of Rubber Used for Gaskets-Tensile strength(After ageing 3 days in Aie-oven Change From Original Value))	-
3.4-Table 1(iv-c) (Requirements of Rubber Used for Gaskets-Elongation at break(After ageing 3 days in Aie-oven Change From Original Value))	-

-
Excluding Hardness, Tensile, Elongation and compression, Test Facility for chemical test is not available

164

IS 7452 (1990)

Hot rolled steel sections for doors, windows and ventilators - Specification

Rs 1800/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
cl 6 (Dimensions)	-
cl 7 (MASS AND MASS TOLERANCE)	-
cl 9 (BEND TEST)	-
cl 8 (SURFACE FINISH)	-
Cl 5.1 (Carbon- IS 228(Part 1))	-
5.1 (Sulphur- IS 228(Part 9))	-
5.1 (Phosphorous- IS 228(Part 3))	-
5.1 (Manganese- IS 228(Part 2))	-
5.1 (Silicon- IS 228(Part 8))	-
5.1 (Nitrogen-IS 228(P-19))	-

-
Mechanical-Complete Facility for chemical test is not available

165

IS 1538 (1993)

Cast iron fittings for pressure pipes for water, gas and sewage - Specification (Third Revision)

Rs 2700/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (The metal used for the manufacture of pipe shall be of a quality not less than that specified for grade FG 150 of IS 210 )	-
5.1 (tensile strength)	-
6.1 (Brinell hardness tests)	-
8 (Hydrostatic Test)	-
9.1,Table 2 & 3 (DI)	-
9.1,Table 2 & 3 (P)	-
9.1,Table 2 & 3 (g)	-
9.1,Table 2 & 3 (h)	-
9.1,Table 2 & 3 (K)	-
9.1,Table 2 & 3 (L)	-
9.1,Table 2 & 3 (M)	-
9.1,Table 2 & 3 (N)	-
9.1,Table 2 & 3 (f)	-
9.1,Table 4 (D)	-
9.1,Table 4 (a)	-
9.1,Table 4 (b)	-
9.1,Table 4 (s)	-
9.1,Table 4 (r)	-
9.1,Table 5 (D)	-
9.1,Table 5 (g)	-
9.1,Table 5 (a)	-
9.1,Table 5 (b)	-
9.1,Table 5 (c)	-
9.1,Table 5 (f)	-
9.1,Table 5 (s)	-
9.1,Table 5 (C)	-
9.1,Table 6 (Holes No)	-
9.1,Table 6 (Holes diameter)	-
9.1,Table 6 (Diameterof Bolts)	-
9.1&11.1,Table 7,8&9 (e)	-
9.1&11.1,Table 7,8&9 (l)	-
9.1&11.1,Table 10 to13 (Mass (Approx))	-
9.1&11.1,Table 10 to13 (e)	-
9.1&11.1,Table 10 to13 (r)	-
9.1&11.1,Table 10 to13 (a)	-
9.1&11.1,Table 10 to13 (b)	-
9.1&11.1,Table 10 to13 (Mass (Approx))	-
9.1&11.1,Table 15 (e)	-
9.1&11.1,Table 14 (Nominal Diameter)	-
9.1&11.1,Table 15 (e1)	-
9.1&11.1,Table 14 (l)	-
9.1&11.1,Table 14 (h)	-
9.1&11.1,Table 24 (Mass (Approx))	-
9.1&11.1,Table 25 (e)	-
9.1&11.1,Table 25 (l)	-
9.1&11.1,Table 24 (h)	-
9.1&11.1,Table 25 (Mass (Approx))	-
9.1&11.1,Table 26 (e1)	-
9.1&11.1,Table 26 (h1)	-
9.1&11.1,Table 26 (Nominal Diameter)	-
9.1&11.1,Table 26 (e2)	-
9.1&11.1,Table 26 (l2)	-
9.1&11.1,Table 26 (l3)	-
9.1&11.1,Table 26 (l)	-
9.1&11.1,Table 26 (Mass (Approx))	-
9.1&11.1,Table 27 (dn)	-
9.1&11.1,Table 27 (e1)	-
9.1&11.1,Table 27 (b)	-
9.1&11.1,Table 27 (l3)	-
9.1&11.1,Table 27 (l2)	-
9.1&11.1,Table 27 (e2)	-
9.1&11.1,Table 27 (r)	-
9.1&11.1,Table 27 (l1)	-
9.1&11.1,Table 27 (Mass)	-
9.1&11.1,Table 28 (D)	-
9.1&11.1,Table 28 (t)	-
9.1&11.1,Table 28 (Mass (Approx))	-
12.1 to 12.7 (Coating )	-

-
Excluding HST for DN above 300 mm

166

IS 15647 (2006)

Hot rolled steel narrow width strip for welded tubes and pipes

Rs.9900/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (UTM)	-
Cl 9 (Press)	-
Cl 11 (Workmanship)	-
Cl 12 (Length, Width & Thickness)	-
Cl 13 (Workmanship)	-
7 (Carbon as C - IS:228)	-
7 (Sulphur as S- IS:228)	-
7 (Manganese as Mn-IS:228)	-
7 (Phosphorus as P-IS:228)	-
7 (Silicon as S-IS:228)	-
7 (Nitrogen IS 228 (part 19) IS 8811: 1998)	-
7 (Aluminium -IS:228)	-
7 (Chromium IS 8811: 1998)	-
7 (Nickel IS 8811: 1998)	-
7 (Boron IS 8811: 1998)	-
7 (Titanium IS 8811: 1998)	-
7 (Niobium IS 8811: 1998)	-
7 (Vanadium IS 8811: 1998)	-
5.2 (Molybednum Astime 1086: 2014)	-

-
Test facility is complete

167

IS 1566 (1982)

Specification for hard - Drawn steel wire fabric for concrete reinforcement (Second Revision)

Rs 300/- + mat test as per IS:432(Pt 2) View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 (DIMENSIONS)	-
7 (SIZES OF SHEETS ‘OR ROLLS)	-
8 (MASS)	-
9.2 (Tolerance on Size of Mesh)	-
9.3 (Tolerance on Size of Sheet)	-
9.4 (Tolerance on Mass of Fabric)	-
10 (MECHANICAL PROPERTIES)	-
11.2 (Tensile Test)	-
11.3 (Reverse Bend Test)	-

-
Test facility is complete

168

IS 4397 (1999)

Cold - Rolled carbon steel strips for ball and roller bearing cages retainers - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (Freedom from defects )	-
8 ( Bend Test )	-
9 (Hardness-IS 1500: Pt 1)	-
14 ( ROLLING TOLERANCES)	-
Cl. 5.2, 6.1, 6.1.1, 6.2 Table 1 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.2, 6.1, 6.1.1, 6.2 Table 1 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.2, 6.1, 6.1.1, 6.2 Table 1 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.2, 6.1, 6.1.1, 6.2 Table 1 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.2, 6.1, 6.1.1, 6.2 Table 1 (Aluminium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.2, 6.1, 6.1.1, 6.2 Table 1 (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.2, 6.1, 6.1.1, 6.2 Table 1 (Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.2, 6.1, 6.1.1, 6.2 Table 1 (Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.2, 6.1, 6.1.1, 6.2 Table 1 (Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.2, 6.1, 6.1.1, 6.2 Table 1 (Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.2, 6.1, 6.1.1, 6.2 Table 1 (Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.2, 6.1, 6.1.1, 6.2 Table 1 (Niobium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.2, 6.1, 6.1.1, 6.2 Table 1 (Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.2, 6.1, 6.1.1, 6.2 Table 1 (Titanium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.2, 6.1, 6.1.1, 6.2 Table 1 (Boron- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-

-
Excluding Micro examination, Cupping test.

169

IS 1537 (1976)

Specification for vertically cast iron pressure pipes for water, gas and sewage (First Revision)

Rs. 3972/- (for flanged ends only) + materials as per View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 , 6 of IS 210 ( The composition of cast iron shall be left to the discretion of the manufacturer)	-
4.1 (Tensile Strength)	-
4.2 (Hardness test)	-
6.1 (Hydrostatic test)	-
7.1 & Table 2 (DE)	-
7.1 & Table 2 (DI)	-
7.1 & Table 2 (P)	-
7.1 & Table 2 (g)	-
7.1 & Table 2 (h)	-
7.1 & Table 2 (DC)	-
7.1 & Table 2 (c)	-
7.1 & Table 2 (f)	-
7.1 & Table 3 (DI)	-
7.1 & Table 3 (P)	-
7.1 & Table 3 (g)	-
7.1 & Table 3 (h)	-
7.1 & Table 4 (D)	-
7.1 & Table 4 (a)	-
7.1 & Table 4 (b)	-
7.1 & Table 4 (s)	-
7.1 & Table 4 (r)	-
7.1 & Table 5 (D)	-
7.1 & Table 5 (C)	-
7.1 & Table 5 (Holes Number)	-
7.1 & Table 5 (Holes Diameter)	-
7.1 & Table 5 (Diameter of Bolts)	-
7.1 & Table 6 to 8 (DE)	-
7.1 & Table 6 to 8 (t)	-
7.1 & Table 6 to 8 (Mass of one meter barrel (Approx))	-
7.1 & Table 6 to 8 (Socket mass (Approx))	-
7.1 & Table 6 to 8 (Total mass for one working length in meter)	-
8.4 (Permissible deviation from a straight line)	-
9.1,Table 9 (DE)	-
9.1,Table 9 (e)	-
9.1,Table 9 (Flange, Mass of one meter (Approx))	-
9.1,Table 9 (Mass of one flange (Approx))	-
9.1,Table 9 (Working Length)	-
10.1 to 10.6 (Coating )	-
3.1 , 6 of IS 210 ( The composition of cast iron shall be left to the discretion of the manufacturer)	-
7.1 & Table 5 (Holes Number)	-

-
Excluding HST for size above 300 mm, Facility for chemical test is not available

170

IS 1536 (2001)

Centrifugally cast (Spun) iron pressure pipes for water, gas and sewage - Specification (Fourth Revision)

Rs.4500.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
11.2, annex-A (Tensile Test ( for pipes over 300mm))	-
11.3 (Brinell Hardness Test)	-
13.3 Table 3 (DE)	-
13.3 Table 3 (DI)	-
13.3 Table 3 (p)	-
13.3 Table 3 (g)	-
13.3 Table 3 (a(optional))	-
13.3 Table 3 (h)	-
13.3 Table 3 (K)	-
13.3 Table 3 (L)	-
13.3 Table 3 (M)	-
13.3 Table 3 (f)	-
13.3 Table 3 (N)	-
13.3 Table 4 (DE)	-
13.3 Table 4 (X)	-
13.3 Table 4 (DI)	-
13.3 Table 4 (P)	-
13.3 Table 4 (Q)	-
13.3 Table 4 (I)	-
13.3 Table 4 (J)	-
13.3 Table 4 (K)	-
13.3 Table 4 (N)	-
13.3 Table 4 (O)	-
13.3 Table 4 (S)	-
13.3 Table 4 (T)	-
13.3 Table 4 (L)	-
13.3 Table 4 (M)	-
13.4 Table 5 (c)	-
13.4 Table 5 (D)	-
13.4 Table 5 (E)	-
13.4 Table 5 (b)	-
13.4 Table 5 (a)	-
13.4 Table 5 (r)	-
13.4 Table 5 (s)	-
13.4 Table 5 (Holes Number)	-
13.4 Table 5 (Holes Diameter)	-
13.4 Table 5 (Diameter of Bolts)	-
13.5 Table 6 to 8 (DE Lead joint)	-
13.5 Table 6 to 8 (DE Push on joint)	-
13.5 Table 6 to 8 (e)	-
13.6 Table 9 (DE)	-
13.6 Table 9 (e)	-

-
Standard has been revised as IS 1536 : 2023 Excluding HST for DN above 300 mm

171

IS 14846 (2000)

Sluice valve for water works purposes (50 To 1200 mm size) - specification

complete testing charges for the product are Rs.5700.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (Nominal Sizes)	-
5.1.1 (Actual Bore)	-
6 (Material)	-
7.2.1 (Manufacture - Bodies and Bonnets)	-
7.2.2 (Manufacture - Bodies and Bonnets)	-
7.2.3 (Manufacture)	-
7.2.4 (Manufacture)	-
7.3 Table 3A 1 (Flanges)	-
7.3 Table 3A 2 (Flanges)	-
7.3 Table 3A 3 (Flanges)	-
7.3 Table 3A 4 (Flanges)	-
7.3 Table 3A 5 (Flanges)	-
7.3 Table 3A 6 (Flanges)	-
7.4.1 (Wedges )	-
7.4.1 (Wedges)	-
7.4.1 (Wedges)	-
7.4.2 (Wedge Faces)	-
7.5 (Guides and Lugs)	-
7.5.1 (Guides and Lugs)	-
7.6 Table 4 (Facing or Seat Rings)	-
7.6 Table 4 (Facing or Seat Rings)	-
7.6 Table 4 (Facing or Seat Rings)	-
7.6 Table 4 (Facing or Seat Rings)	-
7.7.1 Table 2,3 (Dimension of Stem and Wedge Nuts)	-
7.7.1 Table 2,3 (Dimension of Stem and Wedge Nuts)	-
7.7.1 Table 2,3 (Dimension of Stem and Wedge Nuts)	-
7.7.1 Table 2,3 (Dimension of Stem and Wedge Nuts)	-
7.7.1 Table 2,4 (Dimension of Stem and Wedge Nuts)	-
7.7.1 Table 2,5 (Dimension of Stem and Wedge Nuts)	-
7.7.2 (Stem and Wedge Nuts)	-
7.7.3 (Stem and Wedge Nuts)	-
7.7.4 (Stem and Wedge Nuts)	-
7.9 (Height of Valve)	-
7.11 (Hand Wheel)	-
7.11 (Hand Wheel)	-
7.11 (Hand Wheel)	-
7.12 (Valve Caps)	-
7.12 (Valve Caps)	-
7.12 (Valve Caps)	-
7.12 (Valve Caps)	-
7.13 Table 2, 3 (Stuffing Box )	-
7.13 Table 2, 3 (Stuffing Box )	-
7.13 Table 2, 3 (Stuffing Box )	-
7.13 Table 2, 3 (Stuffing Box )	-
7.14 (By Pass Arrangements)	-
7.14 (By Pass Arrangements)	-
8 (Accessories or Optical Features)	-
9 (Coating)	-
10.1 Annex B-1 (Hydraulic Test)	-
10.1 Annex B-2 (Hydraulic Test)	-
10.2 (Flaw Detection Test for Stems)	-

-
Facility for chemical test is not available and HST above 300 mm

172

IS 14756 (2017)

Stainless steel cookware - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Shape and Dimension,)	-
4.2 (Thickness)	-
5.1 (Workmanship And Finish)	-
5.2 (Workmanship And Finish)	-
5.3 (Workmanship And Finish)	-
5.4 (Workmanship And Finish)	-
6.2 (Mechanical Shock Test (for cladded utensils only))	-

-
Handle test, Thermal shock test, Dry heat test, Test facility for chemical testing is not available

173

IS 12817 (2013)

Stainless steel butt hinges - Specification (Second Revision)

Rs. 2400/- and testing charges as per referred Iss View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.2, Table 1 to 6 (Length , A -IS 12817)	-
6.2, Table 1 to 6 (Breadth, B-IS 12817)	-
6.2, Table 1 to 6 (Breadth, B1-IS 12817)	-
6.2, Table 1 to 6 (Breadth, B2-IS 12817)	-
6.2, Table 1 to 6 (Thickness of flap, C-IS 12817)	-
6.2, Table 1 to 6 (Dia. of Hinge pin, D-IS 12817 )	-
6.2, Table 1 to 6 (Number of Knuckles- IS 12817 )	-
6.2, Table 1 to 6 (Number of Screw Holes -IS 12817 )	-
6.2, Table 1 to 6 (Holes for Screw Number- IS 12817 )	-
7.1 (General - IS 12817 )	-
7.2 (Knuckles - IS 12817 )	-
7.3 (Pins- IS 12817 )	-
7.4 (Screw Holes- IS 12817 )	-
7.4.2 (Position of screw holes - IS 12817 )	-
7.4.2, Fig 1 (The distance of the screw holes from the end of the flap - IS 12817 )	-
8 (Finish - IS 12817 )	-

-
Test facility is complete, Test facility for chemical is not available.

174

IS 1783 : Part 1 (2014)

Drums large, fixed ends - Specification: Part 1 grade A drums (Fourth Revision)

Rs.4800/- and testing charges as per relevant referred View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (Capacity)	-
5 (Dimensions (Type 1 C Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 C Drums Figure 2))	-
5 (Dimensions (Type 1 D Drums Figure 2))	-
6 (Material)	-
7.1 (Construction)	-
7.2 (Construction)	-
7.3 (Construction)	-
7.4 (Construction)	-
7.5 (Construction)	-
7.6 (Construction)	-
8 (Finish )	-
9.3 (Hydraulic Pressure Test)	-
9.2 (Drop Test)	-

-
Excluding Microalloying Elements

175

IS 12592 (2002)

Precast concrete manhole cover and frame - Specification (First Revision)

1809 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3 (Grade)	-
3 (Type/Shape of Cover)	-
4.4 (Reinforcement)	-
4.4 (Reinforcement)	-
4.5 (Steel Fibres - Diameter / equivalent diameterofsteel tibres)	-
4.5 (Steel Fibres - The aspect ratio of the tibres)	-
5.2 and Table 1 (Dimensions of Frame - A)	-
5.2 and Table 1 (Dimensions of Frame - B)	-
5.2 and Table 1 (Dimensions of Frame - C)	-
5.2 and Table 1 (Dimensions of Frame - D)	-
5.2 and Table 1 (Dimensions of Frame - E)	-
5.2 and Table 1 (Dimensions of Frame - F)	-
5.2 (Dimensions of cover- Diameter)	-
5.2 (Clearance at top between the frame and the cover all round the periphery)	-
5.2 (Top surface ofthe frame and cover is in level)	-
5.2 (Suitable taper matching with taper given for the frame shall be provided to the periphery of the cover)	-
5.2 and Fig 1 (Clear cover to reinforcement)	-
5.2 and Fig 1 (Distance of housing from the edge)	-
7.4.1 (Edge Protection and Finishing - Frame)	-
7.4.1 (Edge Protection and Finishing - Frame)	-
7.4.1 (Edge Protection and Finishing - Frame)	-
7.4.1 (Edge Protection and Finishing - Frame)	-
7.4.2 (Edge Protection and Finishing - Cover)	-
8 (LIFTING HOOKS)	-
9.1 (General)	-

-
Excluding Load Test

176

IS 2785 (1979)

Specification for natural cheese (Hard Variety), processed cheese, processed cheese spread and soft cheese (First Revision)

Rs 3000/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.3.1 (Appearance)	-
3.3.2 (Odour and Flavour)	-
3.3.3 (Texture and Consistency)	-
3.3.4- Table 1-i (Moisture- Annex A)	-
3.3.4- Table 1-ii (Milk fat ( on dry basis)- Annex B)	-
3.3.4- Table 1-iii (Salt ( added sodium chloride)- Annex C)	-
3.3.4- Table 1-i (Moisture- Annex A)	-

-
Excluding Lactose Content

177

IS 733 (1983)

Specification for wrought aluminium and aluminium alloy bars, rods and sections (For General Engineering Purposes) (Third Revision)

450/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 5.1, Table 2 (Tensile Strength- IS 1816)	-
Cl. 5.1, Table 2 (Elongation on 50 mm or 5.65√So Gauge Length)	-
Cl. 0.4, 5.1, Table 1 (Aluminium- IS 504 or by any other suitable instrumental method)	-
Cl. 0.4, 5.1, Table 1 (Copper- IS 504 or by any other suitable instrumental method)	-
Cl. 0.4, 5.1, Table 1 (Silicon- IS 504 or by any other suitable instrumental method)	-
Table-1, Clause - 5.1 (Manganese)	-
Cl. 0.4, 5.1, Table 1 (Iron- IS 504 or by any other suitable instrumental method)	-
Cl. 0.4, 5.1, Table 1 (Zinc- IS 504 or by any other suitable instrumental method)	-
Cl. 0.4, 5.1, Table 1 (Titanium and / or other grain refining elements - IS 504 or by any other suitable instrumental method)	-
Cl. 0.4, 5.1, Table 1 (Chromium- IS 504 or by any other suitable instrumental method)	-
Cl. 0.4, 5.1, Table 1 (Ti+ V- IS 504 or by any other suitable instrumental method)	-
Cl. 0.4, 5.1, Table 1 (Total Impurities- IS 504 or by any other suitable instrumental method)	-
Cl. 0.4, 5.1, Table 1 (Cr+ Mn- IS 504 or by any other suitable instrumental method)	-

-
Complete except 0.2% proof stress facility

178

IS 3419 (1988)

Specification for fittings for rigid non - Metallic (Second Revision)

2700.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8 & 5 (Visual Examination -IS:3419)	-
6.2 & 9.1- Table-1, ii (Inside Diameter of Collar for Slip type cuplers -IS:3419)	-
6.2 & 9.1- Table-1, iii (Inside Diameter of Ridge for Slip type cuplers -IS:3419)	-
6.2 & 9.1- Table-1, iv (Minimum overall length for Slip type cuplers -IS:3419)	-
6.2 & 9.1- Table-1, v (Minimum wall thickness for Slip type cuplers -IS:3419)	-
6.2 & 9.1- Table-2, ii (Inside Diameter of Collar for Socketed type cuplers -IS:3419)	-
6.2 & 9.1- Table-2, iii (Inside Diameter of Ridge for Socketed type cuplers -IS:3419)	-
6.2 & 9.1- Table-2, iv (Minimum overall length (a) for Socketed type cuplers -IS:3419)	-
6.2 & 9.1- Table-2, v (Minimum overall length (l) for Socketed type cuplers -IS:3419)	-
6.2 & 9.1- Table-2, vi (Minimum wall thickness for Socketed type cuplers -IS:3419)	-
6.2 & 9.1- Table-3, ii (Inside Diameter of Collar(d6) for Clamp type cuplers -IS:3419)	-
6.2 & 9.1- Table-3, iii (Inside Diameter of Collar (d5) for Clamp type cuplers -IS:3419)	-
6.2 & 9.1- Table-3, iv (Inside Diameter of Ridge for Clamp type cuplers -IS:3419)	-
6.2 & 9.1- Table-3, iv (Minimum length for Clamp type cuplers -IS:3419)	-
6.2 & 9.1- Table-3, vi (Minimum wall thickness for Clamp type cuplers -IS:3419)	-
6.2 & 9.1- Table-4, ii (Outside Dameter of Normal type bend -IS:3419)	-
6.2 & 9.1- Table-4, iii (Minimum Inside Diameter of Normal Type Bend -IS:3419)	-
6.2 & 9.1- Table-4, v (Length (l1) of Normal Type Bend -IS:3419)	-
6.2 & 9.1- Table-5, ii (Outside Dameter of Slip type cupling bend -IS:3419)	-
6.2 & 9.1- Table-5, iii (Minimum Inside Diameter of Slip type cupling bend -IS:3419)	-
6.2 & 9.1- Table-5, iv (Inside Diameter of collar for Slip type cupling bend -IS:3419)	-
6.2 & 9.1- Table-5, v (R- for Slip type cupling bend -IS:3419)	-
6.2 & 9.1- Table-5, vi (Y- for Slip type cupling bend -IS:3419)	-
6.2 & 9.1- Table-5, vii (l2- for Slip type cupling bend -IS:3419)	-
6.2 & 9.1- Table-6, ii (Inside Diameter of collar for Normal type Elbows -IS:3419)	-
6.2 & 9.1- Table-6, iii (Length (l) of Normal Type Elbows -IS:3419)	-
6.2 & 9.1- Table-6, iv (Radious(r) of Normal Type Elbows -IS:3419)	-
6.2 & 9.1- Table-6, v (Minimum wall thicknes of Elbows -IS:3419)	-
6.2 & 9.1- Table-7, ii (Inside Diameter of Collear for Normal type Tees -IS:3419)	-
6.2 & 9.1- Table-7, iii (Length (l) of Normal type Tees -IS:3419)	-
6.2 & 9.1- Table-7, iv (Radious(r) of Normal type Tees -IS:3419)	-
6.2 & 9.1- Table-7, v ( Minimum wall thicknes of Normal type Tees -IS:3419)	-
6.2 & 9.1- Table-8, ii (Inside Diameter of Collear for socketed type Tees - IS:3419)	-
6.2 & 9.1- Table-8, iii (a - of socketed type Tees -IS:3419)	-
6.2 & 9.1- Table-8, iv (l - of socketed type Tees -IS:3419)	-
6.2 & 9.1- Table-8, v (Minimum wall thicknes of socketed type Tees -IS:3419)	-
6.2 & 9.1- Table-9, ii (B - of spout Type Circular Boxes -IS:3419)	-
6.2 & 9.1- Table-9, iii (C - of spout Type Circular Boxes -IS:3419)	-
6.2 & 9.1- Table-9, iv (D - of spout Type Circular Boxes -IS:3419)	-
6.2 & 9.1- Table-9, v (E - of spout Type Circular Boxes -IS:3419)	-
6.2 & 9.1- Table-9, vi (F(Max) - of spout Type Circular Boxes -IS:3419)	-
6.2 & 9.1- Table-9, vii (F(Min) - of spout Type Circular Boxes -IS:3419)	-
6.2 & 9.1- Table-9, viii (G - of spout Type Circular Boxes -IS:3419)	-
6.2 & 9.1- Table-9, ix (t - of spout Type Circular Boxes -IS:3419)	-
10 (Resistance to Heat -IS:3419)	-
11 (Resistance to Burning - IS 3419)	-
12 (Moisture Absorption - IS 3419)	-
14.1 (Copper Test - IS 3419)	-
15, 15.3 (Resistance to Oil - IS 3419)	-
15,15.4 (Resistance to Oil - IS 3419)	-
16- Appendix-A (Resistance to Impact -IS 3419)	-
17.2 (Electric Strength - IS 3419)	-
17.3 (Insulation Resistance - IS 3419)	-

-
"Test facility is complete "

179

IS 12146 (1987)

Specification for carbon manganese steel forgings for pressure vessels

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1, Table 3 (Tensile Test-1608:Part 1)	-
6.1, Table 3 (Yield Strength, Mpa)	-
6.1, Table 3 (Elongation, %)	-
7 (Workmanship & Finish)	-
8 (Freedom from defects)	-
6.1, Table 3 (Reduction in area, Percent)	-
Cl. 5.1 & Table 1 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl 5.2 (Sulphur- IS 228(Part 9))	-
Cl. 5.1 & Table 1 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.1 & Table 1 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.1 & Table 1 (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-

-
"Test facility is complete "

180

IS 9537 : Part 3 (1983)

Specification for conduits for electrical installations: Part 3 rigid plain conduits of insulating meterials

Please check remarks View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 (Marking)	-
6.2 (Durability of Marking as per 6.4 of IS: 9537 (Part 1)-1980)	-
6.3 (Standard Mark on Conduit)	-
7.1.1 (Maximum and minimum outside diameter of socket)	-
7.1.1 Table-2 (Length of Socket end)	-
7.1.1 (Maximum and minimum outside diameter of socket)	-
7.1.1 Table-2 (Length of Socket end)	-
7.1.2 (Maximum and minimum outside diameter of conduit)	-
7.2 (Minimum inside diameter of conduit)	-
7.3 (Length of conduit)	-
7.4 (Unifomity of The wall Thickness)	-
8.1 (Construction as per clause 8 of IS: 9537 (Part 1)-1980)	-
9.2 (Bending Test i) At Room Temp ii) At Low Temp (-5 ±2°C))	-
9.3 (Compression Test as per caluse 9.3 of IS: 9537 (Part 1)-1980)	-
9.4 (Impact Test as per clause 9.4 of IS: 9537 (Part 1)-1980)	-
9.5 (Collapse Test as per clause 9.5 of IS: 9537 (Part 1)-1980)	-
9.3 (Compression Test as per caluse 9.3 of IS: 9537 (Part 1)-1980)	-
9.5 (Collapse Test as per clause 9.5 of IS: 9537 (Part 1)-1980)	-
10 (Resistance to Heat -Ball presure test)	-
11 (Resistance to burning as per clause 11 of IS: 9537 (Part 1)-1980)	-
12 (Electrical Characteristics-Test for electric strength as per clause 12.1.1 of IS: 9537 (Part 1)-1980)	-
12 (Electrical Characteristics-Insulation resistance test as per clause 12.1.2 of IS: 9537 (Part 1)-1980)	-

-
"Test facility is complete "

First
Prev
5
6
7
8
Next
Last

Bureau of Indian Standards

The National Standards Body of India

BIS, Northern Regional Laboratory (NRL)

B-69, Industrial Focal Point, Phase VII, Mohali, Mohali, S.A.S Nagar, Punjab, 160059

- nrol@bis.gov.in

Scope List