BIS - LIMS (Laboratory Information Management System)

Search by IS Number

Reset

14051 Results

S.No.

Lab Name

Osl Code

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

4111

Ahmedabad Textile Industry's Research Association (ATIRA), Ahmedabad

7173002

IS 15909 (2020)

PVC Geomembranes for Lining - Specification ( Second Revision )

183180 View breakup
Revised testing charges have been approved w.e.f 18.03.2025

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5,Table 1(Length )	-	300	-
5,Table 1(Width )	-	300	-
5,Table 1(Thickness)	-	450	-
5,Table 1( Tensile strength (Longitudinal) ,kg/m2)	-	900	-
5, Table-2(Dimensional Stability at 80 degree C)	-	1100	-
5,Table 1( Tensile strength (Transverse) ,kg/m2)	-	0	-
5,Table 1(Elongation at break (Transverse),250 % ,Min)	-	0	-
5,Table 1(Tear resistance (machine direction))	-	900	-
5,Table 1(Tear resistance (Cross direction))	-	0	-
5,Table 1(Index puncture resistance,N)	-	1350	-
5,Table 1(Low temperature crack resistance)	-	1100	-
5,Table 1(Seam strength,kg,Min)	-	1650	-
5,Table 1(Peel strength,kN/m,Min)	-	1600	-
5,Table 1(Volatile Loss ,% ,Max)	-	550	-
5,Table 1(Water extraction,% loss in weight)	-	1150	-
5,Table 1(Stability to ultraviolet radiations,% retension in Tensile strength)	-	45900	-
5,Table 1(Stability to ultraviolet radiations,% retension in Elongation at break)	-	0	-
5, Table-2(Length)	-	0	-
5, Table-2(Width)	-	0	-
5, Table-2(Thickness at 20kPa pressure)	-	0	-
5, Table-2(Tensile Strength (Longitudinal))	-	0	-
5, Table-2(Tensile Strength (Transverse))	-	0	-
5, Table-2(Tear Strength (Machine direction))	-	0	-
5, Table-2(Cold crack resistance at low temperature)	-	0	-
5, Table-2(Change in length after heating)	-	1100	-
5, Table-2(Change in width after heating)	-	1100	-
5, Table-2(Behaviour during perforation)	-	1350	-
5, Table-2(Resistance to acid and alkali)	-	113580	-
5, Table-2(Strength of welded seam shear resistance)	-	0	-
5, Table-2(Resistance to static puncturing)	-	1350	-
5, Table-2(Horizontal rate of burning)	-	1500	-
5, Table-2(Vertical rate of burning)	-	1500	-
5, Table-2(Height of fall without perforation)	-	3500	-
5,Table 1(Specific Gravity)	-	550	-
5,Table 1(Elongation at break (Longitudinal),250 % ,Min)	-	0	-
7.1(Colour ,Surface characteristics and fredom from defects)	-	400	-
5,Table 1(Length )	-	0	-
5,Table 1(Width )	-	0	-
5,Table 1(Thickness)	-	0	-
5,Table 1( Tensile strength (Longitudinal) ,kg/m2)	-	0	-
5, Table-2(Dimensional Stability at 80 degree C)	-	0	-
5,Table 1(Tear resistance (machine direction))	-	0	-
5,Table 1(Index puncture resistance,N)	-	0	-
5,Table 1(Low temperature crack resistance)	-	0	-
5,Table 1(Seam strength,kg,Min)	-	0	-
5,Table 1(Peel strength,kN/m,Min)	-	0	-
5,Table 1(Volatile Loss ,% ,Max)	-	0	-
5,Table 1(Water extraction,% loss in weight)	-	0	-
5,Table 1(Stability to ultraviolet radiations,% retension in Tensile strength)	-	0	-
5, Table-2(Change in length after heating)	-	0	-
5, Table-2(Change in width after heating)	-	0	-
5, Table-2(Behaviour during perforation)	-	0	-
5, Table-2(Resistance to acid and alkali)	-	0	-
5, Table-2(Resistance to static puncturing)	-	0	-
5, Table-2(Horizontal rate of burning)	-	0	-
5, Table-2(Vertical rate of burning)	-	0	-
5, Table-2(Height of fall without perforation)	-	0	-
5,Table 1(Specific Gravity)	-	0	-
7.1(Colour ,Surface characteristics and fredom from defects)	-	0	-

-
Exclusion: Cl 5,Table 1 (Hydrostatic resistance,kg/cm2,Min),Cl 5,Table 1 (Resistance to soil burial)

4112

Universal Testing and Research Centre (Division of Sustainable Stewardship Private Limited)

8169306

IS 848 (2006)

Synthetic resin adhesives for plywood (Phenolic And Aminoplastic) - Specification (Second Revision)

All

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4 Table (i)(BWP (BOiling WaterProof))	-	7000	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
4 Table (i)(BWR (Boiling Water Resistant))	-	7000	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
4 Table (i)(MR (Moisture Ressistant))	-	7000	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
5,7.4(Keeping Quality (Resistance to heat Polymerization))	-	500	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
7.4(Acidity and Alkalinity ( pH))	-	1000	10% Discount to BIS and for others 1.5 times of mentioned testing charges.

28 Nov, 2027

-
Included w.e.f. 24.03.2025

4113

Ahmedabad Textile Industry's Research Association (ATIRA), Ahmedabad

7173002

IS 16392 (2015)

Geosynthetics - Geotextiles for permanent erosion control in hard armor systems - Specification

76590 View breakup
Revised testing charges have been approved w.e.f 18.03.2025

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4.3 Table 1 (i) (d)(Grab strength, N)	-	900	-
Cl 4.3 Table 1 (i) (e)(Sewn seam strength, N)	-	1650	-
Cl 4.3 Table 1 (i) (f)(Trapezidal tear strength, N)	-	900	-
Cl 4.3 Table 1 (i) (h)(CBR puncture strength, N)	-	1350	-
Cl 4.3 Table 1 (i) (j)(Burst strength, kPa)	-	800	-
Cl 4.3 Table 1 (i) (a)(Type of geotextile)	-	200	-
Cl 4.3 Table 1 (i) (b)(Roll length, m)	-	300	-
Cl 4.3 Table 1 (i) (c)(Roll width, m)	-	300	-
Cl 4.3 Table 1 (ii) (b)(Permitttivity, s-1 , Course)	-	1100	-
Cl 4.3 Table 1 (ii) (c)(Apparent Opening Size (AOS), mm, Course)	-	750	-
Cl 4.3 Table 1 (iii) (d)(Ultraviolet stability at 500h, retained strength, percent of original strength)	-	48300	-
Cl 4.3 Table 1 (ii) (b)(Permitttivity, s-1 , Medium)	-	0	-
Cl 4.3 Table 1 (ii) (b)(Permitttivity, s-1 , Fine)	-	0	-
Cl 4.3 Table 1 (ii) (c)(Apparent Opening Size (AOS), mm, Medium)	-	0	-
Cl 4.3 Table 1 (ii) (c)(Apparent Opening Size (AOS), mm, Fine)	-	0	-
Cl 4.3 Table 1 (i) (g)(Abrasion strength)	-	3150	-
4.2, Amd-1(Carbon Black content & Dispersion)	-	550	-
4.2, Amd-1(Type of polymer)	-	12440	Chemical Resistance + Fibre Identification
4.2, Amd-1(Isophthalic acid content)	-	3900	-

-
Exclusion: Cl 4.3 Table 1 (Resistance to installation damage)

4114

Ahmedabad Textile Industry's Research Association (ATIRA), Ahmedabad

7173002

IS 16391 (2015)

Geosynthetics â€“ Geotextiles used in sub-grade separation in pavement structures â€“ Specification

73440 View breakup
Revised testing charges have been approved w.e.f 18.03.2025

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4.3 Table 1 (iii) (d)(Ultraviolet stability at 500h, Retained strength, Percent of original strength)	-	48300	-
Cl 4.3 Table 1 (i) (a)(Type of geotextile)	-	200	-
Cl 4.3 Table 1 (i) (b)(Roll length, m, Min)	-	300	-
Cl 4.3 Table 1 (i) (c)(Roll width, m)	-	300	-
Cl 4.3 Table 1 (i) (d)(Grab strength, N)	-	900	-
Cl 4.3 Table 1 (i) (e)(Sewn seam strength, N)	-	1650	-
Cl 4.3 Table 1 (i) (f)(Trapezidal tear strength, N)	-	900	-
Cl 4.3 Table 1 (i) (g)(CBR puncture strength, N)	-	1350	-
Cl 4.3 Table 1 (i) (h)(Burst strength, kPa)	-	800	-
Cl 4.3 Table 1 (ii) (a)(Permitttivity, s-1)	-	1100	-
Cl 4.3 Table 1 (ii) (b)(Apparent opening size (AOS), mm)	-	750	-
Cl 4.3 Table 1 (iii) (b) of Amd-1(b) Ultraviolet stability at 500h, Retained strength, Percent of original strength, Min)	-	0	-
4.2, Amd-1(Carbon Black Content)	-	550	-
4.2(virgin polyester)	-	4400	-
4.2(Carbon black and carbon black dispersion)	-	0	-
4.1(Geosynthetic materials)	-	11940	Chemical Resistance

-
Exclusion: Cl 4.3 Table 1 Resistance to installation damage

4115

QA TESTING LABORATORIES PRIVATE LIMITED LUCKNOW

9192006

IS 1786 (2008)

High strength deformed steel bars and wires for concretere inforcement - Specification (Fourth Revision)

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 8.1 Table 3(Yield Stress (YS))	-	1000	-
Cl. 8.1 Table 3(Elongation, percentage)	-	1000	-
Cl. 8.1 Table 3(Tensile Strength (TS))	-	1000	-
Cl. 9.3, Table 4(Bend Test )	-	600	-
Cl.9.4 & Cl. 9.4.1(Rebend test)	-	500	-
Cl. 8.1 Table 3(TS/YS ratio)	-	500	-
Cl. 7.2 Table -2 (Nominal Mass)	-	500	-
Cl.4.2 of IS 1786 (Grade:- Fe 415,Fe 415D,Fe 415S,Fe 500,Fe 500D,Fe 500S,Fe 550,Fe 550D,Fe600,Fe 650,Fe 700)(Carbon-IS 228)	-	500	-
Cl.4.2 of IS 1786 (Grade:- Fe 415,Fe 415D,Fe 415S,Fe 500,Fe 500D,Fe 500S,Fe 550,Fe 550D,Fe600,Fe 650,Fe 700)(Sulphur-IS 228)	-	500	-
Cl.4.2 of IS 1786 (Grade:- Fe 415,Fe 415D,Fe 415S,Fe 500,Fe 500D,Fe 500S,Fe 550,Fe 550D,Fe600,Fe 650,Fe 700)(Phosphorous- IS 228)	-	500	-
Cl.4.2 of IS 1786 (Grade:- Fe 415,Fe 415D,Fe 415S,Fe 500,Fe 500D,Fe 500S,Fe 550,Fe 550D,Fe600,Fe 650,Fe 700)(Sulphur & Phosphorous)	-	500	-
Cl.4.2 of IS 1786 (Grade:- Fe 415D,Fe 415S, Fe 500D,Fe 500S,Fe 550D)(Carbon Equivalent)	-	500	-
Cl 6.1(Length, Width & Thickness)	-	500	-
Cl 5(Deformations and Surface Characteristics)	-	500	-
5.7(PullOut (Bond Test))	-	1000	-
8.18.1 Table 3(Total elongation at maximum force)	-	500	-

03 Dec, 2028

-
-

4116

CIPET: CENTRE FOR SKILLING AND TECHNICAL SUPPORT (CSTS) - (CIPET), AURANGABAD

7123534

IS 16008 : Part 2 (2016)

Agro textiles “ Shade nets for agriculture and horticulture purposes “ Specification Part 2 Shade nets made from mono filament yarns (first revision)

96100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.0(Material)	-	2000	-
4.2(Fabric)	-	1000	500+500
4.3(Colour)	-	500	-
5.0(Types)	-	500	-
6.1(Dimensions and mass)	-	500	-
6.2(Dimensions and mass)	-	500	-
6.2 Table 1(Mass g/m2,Min)	-	500	-
6.2 Table 1(Average breaking strength of shade nets fabric (Strip method,Warpway,Weftway 325 mm × 50 mm test piece with gauge length of 200 mm), N, Min )	-	1100	-
6.2 Table 1(Warpway Weftway)	-	1100	-
6.2 Table 1(Retention of breaking strength after UV exposure, N, Min)	-	64700	2200+62500
6.2 Table 1(Colour fastness to artificial light1)	-	19850	850+19000
6.2 Table 1(Bursting pressure, kgf/cm2, Min)	-	1000	-
6.2 Table 1(Shading %)	-	700	-

31 Dec, 2026

-
Included w.e.f.19.03.2025

4117

Accurate Universal Laboratoies Private Limited, Ahmedabad

7174006

IS 17782 (2021)

FORTIFIED RICE KERNELS-SPECIFICATION

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Description)	-	1000	-
4.1.1(length, breadth, and thickness)	-	2000	-
4.1.2(length, breadth, thickness, thousand kernel weight, and true density)	-	1000	-
4.1.6(ree from added colouring matter, metal peices and other impurities)	-	1500	-
4.3(Pesticides/insecticides residues, poisonous metals, naturally occurring toxic substances and other contaminant Aflatoxins)	-	10000	-
Table-1, (4.1.3, 4.1.5 and 8)(i) Iron, mg/100 g)	-	6000	-
Table-1, (4.1.3, 4.1.5 and 8)(ii) Folic acid, μg/100 g)	-	6000	-
Table-1, (4.1.3, 4.1.5 and 8)(iii) Vitamin B12, μg/100 g)	-	6000	-
Table-2, 4.1.4, 4.1.5 and 8(i) Zinc, mg/100 g)	-	2000	-
Table-2, 4.1.4, 4.1.5 and 8(ii) Vitamin A, μg/100 g)	-	5000	-
Table-2, 4.1.4, 4.1.5 and 8(iii) Thiamine)	-	5000	-
Table-2, 4.1.4, 4.1.5 and 8(iv) Riboflavin (Vitamin B2), mg/100 g)	-	5000	-
Table-2, 4.1.4, 4.1.5 and 8(v) Niacin (Vitamin B3), mg/100 g)	-	500	-
Table-2, 4.1.4, 4.1.5 and 8(vi) Pyridoxine (Vitamin B6), mg/100 g)	-	5000	-
Table-3, 4.1.6 and 8(i) Moisture content,)	-	500	-
Table-3, 4.1.6 and 8(ii) Broken fortified rice kernels,)	-	1000	-
Table-3, 4.1.6 and 8(iii) Foreign matter,)	-	1000	-
Table-3, 4.1.6 and 8(iv) Damaged grains)	-	1000	-
Table-3, 4.1.6 and 8(v) Discolored grains)	-	1000	-
Table-3, 4.1.6 and 8(vi) Chalky grains)	-	1000	-
Table-3, 4.1.6 and 8(vii) Admixture)	-	1000	-
4.5(Cooking Quality)	-	1000	-
4.5.1(Percent solid loss)	-	1000	-
4.5.2(Cooking time)	-	1000	-
4.5.3(Texture of the cooked fortified rice)	-	1000	-
4.5.4(iron, folic acid, vitamin B12)	-	18000	-
Table-4, 4.7 and 8(i) Total plate count,)	-	2000	-
Table-4, 4.7 and 8(ii) Yeasts and moulds,)	-	2000	-
Table-4, 4.7 and 8(iii) Coliform count,)	-	2000	-

20 Sep, 2026

-
-

4118

CENTRAL LEATHER RESEARCH INSTITUTE (CSIR-CLRI), CHENNAI

6167704

IS 17043 : Part 1 (2024)

Shoes - Specification Part 1 Shoes for Services

36700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.2(Design)	-	0	Physical Parameters 13600
Cl-4.3.1(Size)	-	0	-
Cl-4.3.2(Weight)	-	0	-
Cl-4.4(Height of Upper)	-	0	-
Cl-4.5, S.Cl-4.5.2(Ergonomic Feature)	-	0	-
Cl- 4.5.3.1(Upper-outsole bond strength)	-	600	-
Cl.4.5.3.2(Interlayer bond strength)	-	600	-
Cl-4.5, S.Cl-4.5.4(Slip Resistance)	-	1500	-
Cl-4.5.5.1(Electrical Properties-Antistatic footwear)	-	500	-
Cl-4.5, S.Cl-4.5.6(Heat Insulation of Sole Complex)	-	1000	-
Cl-4.5, S.Cl-4.5.7(Cold Insulation of Sole Complex)	-	2000	-
Cl-4.6.1(Material)	-	0	-
Cl.4.5.8(Energy Absorption of Seat Region)	-	500	-
Cl-4.6.2(Tear Strength)	-	200	-
Cl-4.6.3(Water Vapour Permeability and Coefficient)	-	600	-
Cl-4.6.4(Water Penetration and Water Absorption)	-	500	-
Cl-4.7.1(Material)	-	0	-
Cl-4.7.2(Tear Strength)	-	200	-
Cl-4.7.3(Abrasion Resistance)	-	0	-
Cl-4.7.4(Water Vapour Permeability and Coefficient)	-	0	-
Cl. 4.8.1(Material)	-	0	-
Cl-4.8.2(Abrasion Resistance)	-	600	-
Cl-4.8.3(Water Absorption and Desorption)	-	400	-
4.9 Insocks(Insock thickness)	-	0	-
Cl-4.9.1(Material)	-	0	-
Cl-4.9.2(Water Absorption and Desorption)	-	400	-
Cl-4.9.3(Abrasion Resistance)	-	600	-
Cl-4.10(Toe Puff and Counter Stiffener)	-	0	-
Cl-4.11.1(Material)	-	0	-
Cl-4.11.2(Tear Strength)	-	200	-
Cl-4.12(Closing Thread)	-	200	-
Cl-4.13.1(Material)	-	0	-
Cl-4.13.2(Thickness)	-	0	-
Cl-4.13.3(Moulded Density)	-	200	-
Cl-4.13.4(Hardness)	-	400	-
Cl-4.13.5(Ageing Test)	-	800	-
Cl-4.13.6(Tear Strength)	-	200	-
Cl-4.13.7(Abrasion Resistance)	-	600	-
Cl-4.13.8(Flexing Resistance)	-	600	-
Cl-4.14(Eyelet)	-	0	-
Cl-4.15.1(Material)	-	0	-
Cl-4.15.2(Breaking Load and Tag Retention)	-	400	-
Cl-5, Table 1 of IS 17011 (i)(Allergenic and carcinogenic disperse dyes)	-	2100	-
Cl-5, Table no 1 of IS 17011 (ii)(Aromatic amines released from Azo dyes (each individual amine))	-	2100	-
Cl-5, Table no 1 of IS 17011 (iii)(Aromatic amines released from Azo dyes (each individual amine))	-	2100	-
Cl-5, Table no 1 of IS 17011 (iv)(Chromium (VI))	-	2100	-
Cl-5, Table no 1 of IS 17011 (v)(Dimethyl fumarate (DMFU))	-	2100	-
Cl-5, Table no 1 of IS 17011 (vii)(Formaldehyde)	-	2100	-
Cl-5, Table no 1 of IS 17011 (viii)(Organotin compounds)	-	2100	-
Cl-5, Table no 1 of IS 17011 (ix)(PCP-TeCP-TriCP polychlorophenols)	-	2100	-
Cl-5, Table no 1 of IS 17011 (x)(pH)	-	0	-
Cl-5, Table no 1 of IS 17011 (xii)(Nickel, on skin contact)	-	2100	-
Cl-5, Table no 1 of IS 17011 (vi)(Formaldehyde (free or released by partial hydrolysis))	-	2100	-
Cl-5, Table no 1 of IS 17011 (xi)(Phthalates (each individual phthalate))	-	2100	-
Cl-4.5, S.Cl-4.5.3(Bond Strength)	-	0	-
Cl-5(Chemical Requirements)	-	0	For Chemical Parameters 23100
Cl-7(Marking)	-	0	-
Cl-4.2(Design)	-	0	-
Cl-4.3.1(Size)	-	0	-
Cl-4.3.2(Weight)	-	0	-
Cl-4.4(Height of Upper)	-	0	-
Cl-4.5, S.Cl-4.5.2(Ergonomic Feature)	-	0	-
Cl- 4.5.3.1(Upper-outsole bond strength)	-	0	-
Cl.4.5.3.2(Interlayer bond strength)	-	0	-
Cl-4.5, S.Cl-4.5.4(Slip Resistance)	-	0	-
Cl-4.5.5.1(Electrical Properties-Antistatic footwear)	-	0	-
Cl-4.5, S.Cl-4.5.6(Heat Insulation of Sole Complex)	-	0	-
Cl-4.5, S.Cl-4.5.7(Cold Insulation of Sole Complex)	-	0	-
Cl-4.6.1(Material)	-	0	-
Cl.4.5.8(Energy Absorption of Seat Region)	-	0	-
Cl-4.6.2(Tear Strength)	-	0	-
Cl-4.6.3(Water Vapour Permeability and Coefficient)	-	0	-
Cl-4.6.4(Water Penetration and Water Absorption)	-	0	-
Cl-4.7.1(Material)	-	0	-
Cl-4.7.2(Tear Strength)	-	0	-
Cl-4.7.3(Abrasion Resistance)	-	0	-
Cl-4.7.4(Water Vapour Permeability and Coefficient)	-	0	-
Cl. 4.8.1(Material)	-	0	-
Cl-4.8.2(Abrasion Resistance)	-	0	-
Cl-4.8.3(Water Absorption and Desorption)	-	0	-
4.9 Insocks(Insock thickness)	-	0	-
Cl-4.9.1(Material)	-	0	-
Cl-4.9.2(Water Absorption and Desorption)	-	0	-
Cl-4.9.3(Abrasion Resistance)	-	0	-
Cl-4.10(Toe Puff and Counter Stiffener)	-	0	-
Cl-4.11.1(Material)	-	0	-
Cl-4.11.2(Tear Strength)	-	0	-
Cl-4.12(Closing Thread)	-	0	-
Cl-4.13.1(Material)	-	0	-
Cl-4.13.2(Thickness)	-	0	-
Cl-4.13.3(Moulded Density)	-	0	-
Cl-4.13.4(Hardness)	-	0	-
Cl-4.13.5(Ageing Test)	-	0	-
Cl-4.13.6(Tear Strength)	-	0	-
Cl-4.13.7(Abrasion Resistance)	-	0	-
Cl-4.13.8(Flexing Resistance)	-	0	-
Cl-4.14(Eyelet)	-	0	-
Cl-4.15.1(Material)	-	0	-
Cl-4.15.2(Breaking Load and Tag Retention)	-	0	-
Cl-5, Table 1 of IS 17011 (i)(Allergenic and carcinogenic disperse dyes)	-	0	-
Cl-5, Table no 1 of IS 17011 (ii)(Aromatic amines released from Azo dyes (each individual amine))	-	0	-
Cl-5, Table no 1 of IS 17011 (iii)(Aromatic amines released from Azo dyes (each individual amine))	-	0	-
Cl-5, Table no 1 of IS 17011 (iv)(Chromium (VI))	-	0	-
Cl-5, Table no 1 of IS 17011 (v)(Dimethyl fumarate (DMFU))	-	0	-
Cl-5, Table no 1 of IS 17011 (vii)(Formaldehyde)	-	0	-
Cl-5, Table no 1 of IS 17011 (viii)(Organotin compounds)	-	0	-
Cl-5, Table no 1 of IS 17011 (ix)(PCP-TeCP-TriCP polychlorophenols)	-	0	-
Cl-5, Table no 1 of IS 17011 (x)(pH)	-	0	-
Cl-5, Table no 1 of IS 17011 (xii)(Nickel, on skin contact)	-	0	-
Cl-5, Table no 1 of IS 17011 (vi)(Formaldehyde (free or released by partial hydrolysis))	-	0	-
Cl-5, Table no 1 of IS 17011 (xi)(Phthalates (each individual phthalate))	-	0	-
Cl-4.5, S.Cl-4.5.3(Bond Strength)	-	0	-
Cl-5(Chemical Requirements)	-	0	-
Cl-7(Marking)	-	0	-

02 May, 2027

-
Included w.e.f 13.05.2025

4119

CIPET: CENTRE FOR SKILLING AND TECHNICAL SUPPORT (CSTS) - (CIPET), AURANGABAD

7123534

IS 16008 : Part 1 (2016)

Agro textiles “ Shade nets for agriculture and horticulture purposes “ Specification Part 1 Shade nets made from tape yarns (first revision)

43660 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.0(Types)	-	0	-
6.1(Dimensions and Mass - IS 1954)	-	500	-
6.1(Dimensions and Mass - IS 1954)	-	500	-
6.2 Table 1(Mass - IS 1964)	-	500	-
6.2 Table 1(Average breaking strength of shade nets fabric (Strip method, 325 mm x 50 mm test piece with gauge length of 200 mm) - IS 1969 (Part 1))	-	1100	-
6.2 Table 1(Average breaking strength of shade nets fabric (Strip method, 325 mm x 50 mm test piece with gauge length of 200 mm) - IS 1969 (Part 1))	-	1100	-
6.2 Table 1(Retention of breaking strength after UV exposure - IS 1969 (Part 1))	-	2200	-
6.2 Table 1(Colour fastness to artificial light, IS 2454)	-	19850	850+19000
6.2 Table 1(Bursting Pressure, IS 1966 (Part 1 or 2))	-	1000	-
6.2 Table 1(Shading Percentage)	-	700	-
4.3, 4(Colour)	-	500	-
4.2, 4(Fabric )	-	1000	500+500
4.1.1, 4(HDPE Tapes Heat shrinkage )	-	1400	700+700
4.1, 4( HDPE Tapes Linear density )	-	700	-
4.1, 4(HDPE Tapes Width )	-	500	-
4.1, 4(HDPE Tapes UV stabilizer)	-	2000	-
4.1, 4(HDPE Tapes Material Identification )	-	2000	-

31 Dec, 2026

-
Included w.e.f.19.03.2025

4120

Classic Testing & Research Centre (B17), Noida

8180826

IS 16270 (2023)

Secondary cells and batteries for solar photovoltaic application - General requirements and methods of test

700000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(Photovoltaic Energy System)	-	5000	-
Cl-4.2(Secondary Cells and Batteries)	-	5000	-
Cl-4.3(General Operating Conditions)	-	5000	-
Cl-4.3.8(Storage)	-	5000	-
Cl-4.3.9(Operating Temperature)	-	5000	-
Cl-5.1(Mechanical Endurance)	-	5000	-
Cl-5.2(Charge Efficiency)	-	5000	-
Cl-5.3(Deep Discharge Protection)	-	5000	-
Cl-5.4(Marking)	-	5000	-
Cl-5.5(Safety)	-	5000	-
Cl-5.6(Documentation)	-	5000	-
Cl-6(Functional characteristice)	-	5000	-
Cl-7(General test conditions)	-	5000	-
Cl-8.1(Capacity Test)	-	5000	-
Cl-8.2(Endurance Test)	-	5000	-
Cl-8.3(Charge Retention Test)	-	5000	-
Cl-8.4(Cycle Endurance in Photovoltaic Application (Extreme Conditions))	-	5000	-
Cl-8.5(Sulphation Test (Applicable for Lead Acid Batteries only))	-	5000	-
Cl-8.6(Water Loss Test (Valid for Flooded Lead Acid Batteries only))	-	5000	-
Cl-9.1(Type Tests)	-	5000	-
Cl-9.2(Acceptance Test)	-	5000	-
4.3.7.1(Specific gravity)	-	5000	-

15 Oct, 2027

-
-

4121

JBS TESTING SOLUTIONS PVT LTD (27), JALANDHAR

9164606

IS 14650 (2023)

UNALLOYED AND ALLOYED STEEL INGOT AND SEMI-FINISHED PRODUCTS FOR RE-ROLLING PURPOSES - SPECIFICATION (First Revision)

7450 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause - 7.1(CARBON)	-	7450	For complete testing
Clause - 7.1(SULPHUR)	-	7450	For complete testing
Clause - 7.1(PHOSPHURS)	-	7450	For complete testing
Clause - 7.1(MANGANESE)	-	7450	For complete testing
Clause - 7.1(NITROGEN)	-	7450	For complete testing
As per Clause 10(Dimension)	-	7450	For complete testing
As per Clause 10.1(Dimension Width)	-	7450	For complete testing
As per Clause 10.1(Dimension Thickness)	-	7450	For complete testing
As per Clause 10.2(Dimension Length)	-	7450	For complete testing
As per Clause 11/11.1/11.2/11.3/11.4(Tolerances)	-	7450	For complete testing
As per Clause 11.5(Bend)	-	7450	For complete testing
As per Clause 11.6(Camber)	-	7450	For complete testing
As per Clause 11.7 (i)(Out of Square)	-	7450	For complete testing
As per Clause 11.7 (ii)(Round Corners)	-	7450	For complete testing
As per Clause 11.7 (iii)(Ridges due to gas cutting)	-	7450	For complete testing
As per Clause 11.7 (iv)(Taper (Width variation on top and bottom surface at one location)	-	7450	For complete testing
As per Clause 11.7 (v)(Edge slanting (Width variation on top and bottom surface at one location)	-	7450	For complete testing
As per Clause 11.7 (vi)(Convexity(Difference in thickness from edge to curve)	-	7450	For complete testing
As per Clause 11.7 (vii)(Chamfering (Length variation on top and bottom surface at one location)	-	7450	For complete testing
As per Clause 11.7 (viii)(Wedge (Thickness variation at the edges along the cross section)	-	7450	For complete testing
As per Clause 11.7 (ix)(Scarfing pits)	-	7450	For complete testing
As per Clause 12/12.1/12.2/12.3(Freedom from defects)	-	7450	For complete testing
Clause. 13(Macro examination test.)	-	7450	For complete testing
Clause. 13(Macro examination test.)	-	7450	For complete testing
Clause. 13(Sulphur print.)	-	7450	For complete testing
Clause. 13(Inclusion content)	-	7450	For complete testing
Clause. 14(Marking)	-	7450	For complete testing
Clause.15(Ordering information)	-	7450	For complete testing
Clause.6.0(Manufacture)	-	7450	For complete testing
Clause.7.1(Silicon)	-	7450	For complete testing
Clause.7.1(Carbon Equbalant)	-	7450	For complete testing
Clause.7.1(Microalloy element)	-	7450	For complete testing

04 Dec, 2028

-
Included w.e.f.26.05.2025

4122

JBS TESTING SOLUTIONS PVT LTD (27), JALANDHAR

9164606

IS 15509 (2017)

Double - Pitch precision roller chains - Attachments and associated chain sprockets for transmission and conveyors (First Revision)

22500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Transmission chains)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
3.2(Designation)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
3.3(Dimensions)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
3.4.1(General)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
3.4.2(Testing)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
3.5(Preloading)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
3.6(Length validation)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
3.7(Marking)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
4.1(General)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
4.2(Nomenclature)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
4.3(Designation)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
4.4(Dimensions)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
4.5(Length validation)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
4.6(Marking)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
4.7.1(General)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
4.7.2(Nomenclature)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
4.7.3(Designation)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
4.7.4(Dimensions)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
4.7.6(Marking)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
5.1(Nomenclature)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
5.2(Diametral dimensions and tooth shape)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
5.3(Radial run-out)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
5.4(Axial run-out (wobble))	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
5.5(Pitch accuracy of sprocket teeth)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
5.6(Bore tolerance)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
5.7(Marking)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
3(Transmission chains)	-	22500	6000: For Complete dimensional and qualitative tests 10,000: For Complete Mechanical test 6500: For accuracy and other run out tests Total: 22,500
3.2(Designation)	-	0	-
3.3(Dimensions)	-	0	-
3.4.1(General)	-	0	-
3.4.2(Testing)	-	0	-
3.5(Preloading)	-	0	-
3.6(Length validation)	-	0	-
3.7(Marking)	-	0	-
4.1(General)	-	0	-
4.2(Nomenclature)	-	0	-
4.3(Designation)	-	0	-
4.4(Dimensions)	-	0	-
4.5(Length validation)	-	0	-
4.6(Marking)	-	0	-
4.7.1(General)	-	0	-
4.7.2(Nomenclature)	-	0	-
4.7.3(Designation)	-	0	-
4.7.4(Dimensions)	-	0	-
4.7.6(Marking)	-	0	-
5.1(Nomenclature)	-	0	-
5.2(Diametral dimensions and tooth shape)	-	0	-
5.3(Radial run-out)	-	0	-
5.4(Axial run-out (wobble))	-	0	-
5.5(Pitch accuracy of sprocket teeth)	-	0	-
5.6(Bore tolerance)	-	0	-
5.7(Marking)	-	0	-
3(Transmission chains)	-	0	-
3.2(Designation)	-	0	-
3.3(Dimensions)	-	0	-
3.4.1(General)	-	0	-
3.4.2(Testing)	-	0	-
3.5(Preloading)	-	0	-
3.6(Length validation)	-	0	-
3.7(Marking)	-	0	-
4.1(General)	-	0	-
4.2(Nomenclature)	-	0	-
4.3(Designation)	-	0	-
4.4(Dimensions)	-	0	-
4.5(Length validation)	-	0	-
4.6(Marking)	-	0	-
4.7.1(General)	-	0	-
4.7.2(Nomenclature)	-	0	-
4.7.3(Designation)	-	0	-
4.7.4(Dimensions)	-	0	-
4.7.6(Marking)	-	0	-
5.1(Nomenclature)	-	0	-
5.2(Diametral dimensions and tooth shape)	-	0	-
5.3(Radial run-out)	-	0	-
5.4(Axial run-out (wobble))	-	0	-
5.5(Pitch accuracy of sprocket teeth)	-	0	-
5.6(Bore tolerance)	-	0	-
5.7(Marking)	-	0	-
3(Transmission chains)	-	0	-
3.2(Designation)	-	0	-
3.3(Dimensions)	-	0	-
3.4.1(General)	-	0	-
3.4.2(Testing)	-	0	-
3.5(Preloading)	-	0	-
3.6(Length validation)	-	0	-
3.7(Marking)	-	0	-
4.1(General)	-	0	-
4.2(Nomenclature)	-	0	-
4.3(Designation)	-	0	-
4.4(Dimensions)	-	0	-
4.5(Length validation)	-	0	-
4.6(Marking)	-	0	-
4.7.1(General)	-	0	-
4.7.2(Nomenclature)	-	0	-
4.7.3(Designation)	-	0	-
4.7.4(Dimensions)	-	0	-
4.7.6(Marking)	-	0	-
5.1(Nomenclature)	-	0	-
5.2(Diametral dimensions and tooth shape)	-	0	-
5.3(Radial run-out)	-	0	-
5.4(Axial run-out (wobble))	-	0	-
5.5(Pitch accuracy of sprocket teeth)	-	0	-
5.6(Bore tolerance)	-	0	-
5.7(Marking)	-	0	-
3(Transmission chains)	-	-	-
3.2(Designation)	-	-	-
3.3(Dimensions)	-	-	-
3.4.1(General)	-	-	-
3.4.2(Testing)	-	-	-
3.5(Preloading)	-	-	-
3.6(Length validation)	-	-	-
3.7(Marking)	-	-	-
4.1(General)	-	-	-
4.2(Nomenclature)	-	-	-
4.3(Designation)	-	-	-
4.4(Dimensions)	-	-	-
4.5(Length validation)	-	-	-
4.6(Marking)	-	-	-
4.7.1(General)	-	-	-
4.7.2(Nomenclature)	-	-	-
4.7.3(Designation)	-	-	-
4.7.4(Dimensions)	-	-	-
4.7.6(Marking)	-	-	-
5.1(Nomenclature)	-	-	-
5.2(Diametral dimensions and tooth shape)	-	-	-
5.3(Radial run-out)	-	-	-
5.4(Axial run-out (wobble))	-	-	-
5.5(Pitch accuracy of sprocket teeth)	-	-	-
5.6(Bore tolerance)	-	-	-
5.7(Marking)	-	-	-

04 Dec, 2028

-
Included w.e.f.26.05.2025

4123

Universal Testing and Research Centre (Division of Sustainable Stewardship Private Limited)

8169306

IS 303 (2024)

Plywood for General Purposes â Specification (Fourth Revision)

Grade- MR/BWR/BWP, Type- A & B

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.1(Classification by appearance)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-5.2, Table- 1 (i)(Blister)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-5.2, Table- 1 (ii)(Checks)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-5.2, Table- 1 (iii)(Discolouration)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-5.2, Table- 1 (iv)(Dote)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-5.2, Table- 1 (v)(Insect hole)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-5.2, Table- 1 (vi)(Joints)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-5.2, Table- 1 (vii)(Knots (dead))	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-5.2, Table- 1 (viii)(Pin knots (dead))	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-5.2, Table- 1 (ix)(Pin knots (live))	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-5.2, Table- 1 (x)(Knots (tight))	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-5.2, Table- 1 (xi)(Patches)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-5.2, Table- 1 (xii)(Splits)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-5.2, Table- 1 (xiii)(Swirl)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-5.2, Table-2(Maximum Number of Categories of Permissible Defects, per m2)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-6.1(Timber)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-6.2(Adhesive)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-7.2.1(Thickness of veneers)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-7.2.3(Grain Direction)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-7.2.5.1(Gaps in cores and cross-bands)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-7.2.5.2(Splits)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-7.2.5.3(Overlap)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-8.1(Dimensions -length)	-	300	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-8.2(Thickness of the plywood boards)	-	300	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-8.3(Squareness)	-	500	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-11.3.1, 11.3.1.1(Water Resistance Test)	-	500	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-11.3.2(Mycological Test)	-	1500	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-11.4(Moisture Content)	-	500	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-11.5, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average)	-	1000	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-11.5, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Minimum Individual)	-	1000	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-11.6(Formaldehyde Content Test)	-	4600	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-11.7(Steady-State Formaldehyde Emission Test)	-	60000	20% Discount for BIS Samples (Optional Test, Mentioned charges are for the Steady State Formaldehyde Testing 60000/- , Testing Time 30Days)
Cl-9(WORKMANSHIP AND FINISH)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-7.2.4(Scarf Joints)	-	0	10% Discount to BIS and for others 1.5 times of mentioned testing charges.

28 Nov, 2027

-
Included w.e.f. 24.03.2025

4124

JBS TESTING SOLUTIONS PVT LTD (27), JALANDHAR

9164606

IS 2619 (2018)

Glass beakers - Specification (Third Revision)

12400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-	12400	For Complete Testing
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-	12400	For Complete Testing
Cl.6 Material(Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)	-	12400	For Complete Testing
Cl.7.1 Dimensions(Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-	12400	For Complete Testing
Cl.7.2 Radius at base(Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-	12400	For Complete Testing
Cl.7.2 Radius at base(Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-	12400	For Complete Testing
Cl.7.3 Wall thickness(Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-	12400	For Complete Testing
Cl.8.1 Base(The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-	12400	For Complete Testing
8.2 Upper edge(The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-	12400	For Complete Testing
Cl. 8.3 Spout(The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-	12400	For Complete Testing
Cl.8.4 Scale(Beakers may be provided with a scale, which should approximately indicate the volume contained in the beaker.)	-	12400	For Complete Testing
Cl.8.5 Thermal shock resistance(Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-	12400	For Complete Testing
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-	12400	For Complete Testing
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-	12400	For Complete Testing
Cl.6 Material(Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)	-	12400	For Complete Testing
Cl.7.1 Dimensions(Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-	12400	For Complete Testing
Cl.7.2 Radius at base(Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-	12400	For Complete Testing
Cl.7.2 Radius at base(Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-	12400	For Complete Testing
Cl.7.3 Wall thickness(Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-	12400	For Complete Testing
Cl.8.1 Base(The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-	12400	For Complete Testing
8.2 Upper edge(The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-	12400	For Complete Testing
Cl. 8.3 Spout(The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-	12400	For Complete Testing
Cl.8.4 Scale(Beakers may be provided with a scale, which should approximately indicate the volume contained in the beaker.)	-	12400	For Complete Testing
Cl.8.5 Thermal shock resistance(Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-	12400	For Complete Testing
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-	12400	For Complete Testing
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-	12400	For Complete Testing
Cl.6 Material(Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)	-	12400	For Complete Testing
Cl.7.1 Dimensions(Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-	12400	For Complete Testing
Cl.7.2 Radius at base(Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-	12400	For Complete Testing
Cl.7.2 Radius at base(Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-	12400	For Complete Testing
Cl.7.3 Wall thickness(Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-	12400	For Complete Testing
Cl.8.1 Base(The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-	12400	For Complete Testing
8.2 Upper edge(The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-	12400	For Complete Testing
Cl. 8.3 Spout(The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-	12400	For Complete Testing
Cl.8.4 Scale(Beakers may be provided with a scale, which should approximately indicate the volume contained in the beaker.)	-	12400	For Complete Testing
Cl.8.5 Thermal shock resistance(Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-	12400	For Complete Testing

04 Dec, 2028

-
-

4125

JBS TESTING SOLUTIONS PVT LTD (27), JALANDHAR

9164606

IS 915 (2012)

Laboratory glassware - One - Mark volumetric flasks (Third Revision)

11800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1(Material)	-	11800	For Complete Testing
Table 1(Internal Neck Diameter)	-	11800	For Complete Testing
Table 1(Distance of graduation line)	-	11800	For Complete Testing
Table 1(Overall Height)	-	11800	For Complete Testing
Table 1(Bulb Diameter)	-	11800	For Complete Testing
Table 1(Base Diameter)	-	11800	For Complete Testing
Table 1(Wall Thickness)	-	11800	For Complete Testing
Table 1(Ground joint k4)	-	11800	For Complete Testing
Table 1(Ground joint k6)	-	11800	For Complete Testing
8.3(Shape)	-	11800	For Complete Testing
8.4(Neck)	-	11800	For Complete Testing
8.5(Stopper)	-	11800	For Complete Testing
8.6(Dimensions)	-	11800	For Complete Testing
9.0(Graduation Line)	-	11800	For Complete Testing
Table-2(Nominal capacity)	-	11800	For Complete Testing
Table-2(Internal neck diameter)	-	11800	For Complete Testing
Table-2(Distance of graduation line 1))	-	11800	For Complete Testing
Table-2(Overall height 2))	-	11800	For Complete Testing
Table-2(Bulb diameter)	-	11800	For Complete Testing
Table-2(Base diameter)	-	11800	For Complete Testing
Table-2(Wall thickness)	-	11800	For Complete Testing
Table-2(Ground joint 3) k4)	-	11800	For Complete Testing
Table-2(Ground joint 3) k6)	-	11800	For Complete Testing
12.1(Visibility of graduation line, figures and marking)	-	11800	For Complete Testing
12.2(Visibility of graduation line, figures and marking)	-	11800	For Complete Testing
Table 1(Nominal Capacity)	-	11800	For Complete Testing

04 Dec, 2028

-
-

4126

JBS TESTING SOLUTIONS PVT LTD (27), JALANDHAR

9164606

IS 878 (2008)

Laboratory glassware - Graduated measuring cylinders (Second Revision)

9500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Table-1(Nominal capacity)	-	9500	For Complete Testing
Table-1(Overall height)	-	9500	For Complete Testing
Table-1(Distance from top of scale to top of cylinder)	-	9500	For Complete Testing
Table-1(Internal height to highest graduation line)	-	9500	For Complete Testing
Table-1(Sub-divisions)	-	9500	For Complete Testing
Table-1(capacity at lowest graduation line)	-	9500	For Complete Testing
Cl-9.1(Wall thickness)	-	9500	For Complete Testing
Cl-9.2(Stability)	-	9500	For Complete Testing
Cl-9.3(Base)	-	9500	For Complete Testing
Cl-9.4(Rim and spout)	-	9500	For Complete Testing
Cl-9.5(Neck and stopper)	-	9500	For Complete Testing
Cl-9.6, Table-2(Nominal capacity)	-	9500	For Complete Testing
Cl-9.6, Table-2(Overall height)	-	9500	For Complete Testing
Cl-9.6, Table-2(Distance from top of scale to top of cylinder)	-	9500	For Complete Testing
Cl-9.6, Table-2(Internal height to highest graduation line)	-	9500	For Complete Testing
Cl-9.6, Table-2(Sub divisions)	-	9500	For Complete Testing
Cl-9.6, Table-2(capacity at lowest graduation line)	-	9500	For Complete Testing
Cl-10.1(Graduation)	-	9500	For Complete Testing
Cl-10.2(Figuring)	-	9500	For Complete Testing
Cl-11(Accuracy testing)	-	9500	For Complete Testing
Cl-13(Visibility of graduation lines, figures and marking)	-	9500	For Complete Testing

04 Dec, 2028

-
-

4127

IDMA LABORATORIES LIMITED, PANCHKULA

9123236

IS 13422 (2024)

Single-use Sterile Rubber Surgical Gloves ï¿½ Specification (First Revision)

294000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5(Materials)	-	240000	Rs. 240000/- for Conformity of Gloves to Relevant part of ISO 10993 series (Clause 5.4) 1) Cytotoxicity INR 50000 2) Skin Sensitization INR 120000 3) Skin Irritation INR 70000
Cl-6(Sampling and selection of test pieces)	-	0	Inspection level and AQL as per Table 1 not applicable as Testing will be carried out on the Samples as received
Cl-7.1(Dimensions)	-	6000	1) Width (H) INR 2000 2) Minimum Length (L) INR 2000 3) Minimum Thickness INR 2000
Cl-7.2(Watertightness)	-	8000	Testing charges 1) Rs. 39000/- Excluding Sterility (Clause 7.4) and Conformity tests (Clause 5.4) 2. Rs.15000/- for Sterility Test only (Clause 7.4) 3.Rs. 240000/- for Conformity of Gloves to Relevant part of ISO 10993 series (Clause 5.4)
Cl-7.3(Tensile properties)	-	0	As mentioned below
Cl-7.3.2(Force at break and elongation at break before accelerated ageing)	-	5000	Testing Charges 1) Force at break before accelerated ageing INR 2500 2) Elongation at break before accelerated ageing INR 2500
Cl-7.3.3(Force at break and elongation at break after accelerated ageing)	-	10000	Testing Charges 1) Minimum force at break after accelerated ageing INR 5000 2) Minimum Elongation at break after accelerated ageing INR 5000
Cl-7.3.4(Force required to produce 300 % elongation)	-	3000	Testing Charges 1) Force require to produce 300% Elongation before accelerated ageing INR 3000
Cl-7.4(Sterility)	-	15000	No Test Method Prescribed. The Charges are given in case the Sterility is performed as per respective IP. Testing Charges Rs.15000/- for Sterility Test only (Clause 7.4)
Cl-9(Marking.)	-	0	Testing charges for 1) Design as per clause 4.3 is INR 2000 2) Finish as per clause 4.4 is INR 5000
Cl-7.3.1(General)	-	0	-

31 Dec, 2026

-
-

4128

Planet Electro Labs Private Limited (407)

8174226

IS/IEC 61730 : PART 2 (2016)

Photovoltaic (PV) module safety qualification: Part 2 requirements for testing (First Revision)

840000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 10.2(Visual inspection MST 01)	-	5000	-
Clause 10.3(Performance at STC MST 02)	-	20000	-
Clause 10.4(Maximum powerdetermination MST 03)	-	80000	-
Clause 10.5(Insulation thickness test MST 04)	-	10000	-
Clause 10.6(Durability of markings MST 05)	-	5000	-
Clause 10.7(Sharp edge test MST 06)	-	10000	-
Clause 10.8(Bypass diode functionality test MST 07)	-	50000	-
Clause 10.9(Accessibility test MST 11)	-	30000	-
Clause 10.10(Cut susceptibility test MST 12)	-	30000	-
Clause 10.11(Continuity test of equipotential bonding MST 13)	-	25000	-
Clause 10.12(Impulse voltage test MST 14)	-	20000	-
Clause 10.13(Insulation test MST 16)	-	10000	-
Clause 10.14(Wet leakage current test MST 17)	-	75000	-
Clause 10.15(Temperature test MST 21)	-	75000	-
Clause 10.16(Hot-spot endurance test MST 22)	-	75000	-
Clause 10.17(Fire test MST 23)	-	110000	-
Clause 10.18(Ignitability test MST 24)	-	50000	-
Clause 10.19(Bypass diode thermal test MST 25)	-	60000	-
Clause 10.20(Reverse current overload test MST 26)	-	30000	-
Clause 10.21(Module breakage test MST 32)	-	20000	-
Clause 10.22(Screw connections test MST 33)	-	5000	-
Clause 10.23(Static mechanical load test MST 34)	-	40000	-
Clause 10.24(Peel test MST 35)	-	15000	-
Clause 10.25(Lap shear strength test MST 36)	-	15000	-
Clause 10.26(Materials creep test MST 37)	-	10000	-
Clause 10.27(Robustness of terminations test MST 42)	-	15000	-
Clause 10.28(Thermal cycling test MST 51)	-	120000	-
Clause 10.29(Humidity freeze test MST 52)	-	120000	-
Clause 10.30(Damp heat test MST 53)	-	120000	-
Clause 10.31(UV test MST 54)	-	75000	-
Clause 10.32(Cold conditioning MST 55)	-	35000	-
Clause 10.33(Dry heat conditioning MST 56)	-	35000	-
Clause 10.2(Visual inspection MST 01)	-	5000	-
Clause 10.3(Performance at STC MST 02)	-	25000	-
Clause 10.4(Maximum powerdetermination MST 03)	-	40000	-
Clause 10.5(Insulation thickness test MST 04)	-	5000	-
Clause 10.6(Durability of markings MST 05)	-	5000	-
Clause 10.7(Sharp edge test MST 06)	-	10000	-
Clause 10.8(Bypass diode functionality test MST 07)	-	60000	-
Clause 10.9(Accessibility test MST 11)	-	20000	-
Clause 10.10(Cut susceptibility test MST 12)	-	25000	-
Clause 10.11(Continuity test of equipotential bonding MST 13)	-	20000	-
Clause 10.12(Impulse voltage test MST 14)	-	15000	-
Clause 10.13(Insulation test MST 16)	-	5000	-
Clause 10.14(Wet leakage current test MST 17)	-	45000	-
Clause 10.15(Temperature test MST 21)	-	35000	-
Clause 10.16(Hot-spot endurance test MST 22)	-	85000	-
Clause 10.17(Fire test MST 23)	-	75000	-
Clause 10.18(Ignitability test MST 24)	-	25000	-
Clause 10.19(Bypass diode thermal test MST 25)	-	60000	-
Clause 10.20(Reverse current overload test MST 26)	-	20000	-
Clause 10.21(Module breakage test MST 32)	-	20000	-
Clause 10.22(Screw connections test MST 33)	-	15000	-
Clause 10.23(Static mechanical load test MST 34)	-	40000	-
Clause 10.24(Peel test MST 35)	-	15000	-
Clause 10.25(Lap shear strength test MST 36)	-	15000	-
Clause 10.26(Materials creep test MST 37)	-	15000	-
Clause 10.27(Robustness of terminations test MST 42)	-	25000	-
Clause 10.28(Thermal cycling test MST 51)	-	120000	-
Clause 10.29(Humidity freeze test MST 52)	-	100000	-
Clause 10.30(Damp heat test MST 53)	-	75000	-
Clause 10.31(UV test MST 54)	-	60000	-
Clause 10.32(Cold conditioning MST 55)	-	15000	-
Clause 10.33(Dry heat conditioning MST 56)	-	25000	-

05 Nov, 2026

-
Included w.e.f 13.05.2025 Exclusion: Cl. 5.3.3 (External wiring & cables)

4129

Planet Electro Labs Private Limited (407)

8174226

IS/IEC 61730 : PART 1 (2016)

Photovoltaic (PV) Module Safety Qualification Part 1 Requirements for Construction ( First Revision )

490000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.0(Application Classes)	-	5000	-
4.0(Construction Requirements)	-	10000	-
5.0(Polymeric Materials)	-	5000	-
6.0(Internal Wiring and Current Carrying Parts)	-	2000	-
7.0(Connections)	-	20000	-
8.0(Bonding and Grounding)	-	20000	-
9.0(Creepage and clearance distances)	-	5000	-
10.0(Field Wiring Compartments with covers)	-	10000	-
11.0(Marking)	-	5000	-
12.0(Requirements of Supplied documents)	-	5000	-
5.6.4 IS/IEC 61730-1(Distance through Insulation)	-	5000	-
5.6.3 IS/IEC 61730-1(Insulation Coordination)	-	5000	-
5.6.2 IS/IEC 61730-1(Protection Agianst accessibility to hazardeous live parts)	-	8000	-
5.6, 5.6.1 IS/IEC 61730-1(Protection Agianst Electric Shock)	-	10000	-
5.5.4 IS/IEC 61730-1(Adhesives)	-	20000	-
5.5.3.2 IS/IEC 61730-1(Current Carrying Parts)	-	10000	-
5.5.3, 5.5.3.1 IS/IEC 61730-1(Metallic materials)	-	10000	-
5.5.2.4 IS/IEC 61730-1(Polymeric Meterial used for Mechanical functions)	-	15000	-
5.5.2.3.5 IS/IEC 61730-1(Polymeric Insulating Parts supporting live Parts)	-	15000	-
5.5.2.3.4 IS/IEC 61730-1(Polymeric Insulating materials used as external Parts)	-	15000	-
5.5.2.3.3 IS/IEC 61730-1(Endurance to thermal stress-RTE (RTI) or TI)	-	15000	-
5.5.2.3.2 IS/IEC 61730-1(Endurance to Electrical Stress)	-	25000	-
5.5.2 IS/IEC 61730-1(Polymeric Materials)	-	10000	-
5.5, 5.5.1 IS/IEC 61730-1(Materials)	-	10000	-
5.4.7 IS/IEC 61730-1(Other Connections)	-	10000	-
5.4.6 IS/IEC 61730-1(Connections by adhesives)	-	10000	-
5.4.5 IS/IEC 61730-1(Form/Press/Tight/Fit)	-	5000	-
5.4.4 IS/IEC 61730-1(Thread Cutting Screws)	-	10000	-
5.4.3 IS/IEC 61730-1(Rivets)	-	10000	-
5.4.2 IS/IEC 61730-1(Screw Connctions)	-	10000	-
5.4, 5.4.1 IS/IEC 61730-1(Mechanical and Electromechanical connections)	-	10000	-
5.3.10 IS/IEC 61730-1(Bypass Diodes)	-	10000	-
5.3.9 IS/IEC 61730-1(Encapsulants)	-	10000	-
5.3.8 IS/IEC 61730-1(Electrical Connections)	-	10000	-
5.3.7 IS/IEC 61730-1(Insulation Barrier)	-	10000	-
5.3.6 IS/IEC 61730-1(Front sheet and back Sheet)	-	10000	-
5.3.5 IS/IEC 61730-1(Junction Box for PV modules)	-	10000	-
5.3.4 IS/IEC 61730-1(Connectors)	-	10000	-
5.3.3 IS/IEC 61730-1(External Wirings and cables)	-	10000	-
5.3.2 IS/IEC 61730-1(Internal Wiring)	-	10000	-
5.3, 5.3.1 IS/IEC 61730-1(Electrical Components and Insualtion)	-	10000	-
5.2 IS/IEC 61730-1(Marking and Documentation)	-	5000	-
5, 5.1 IS/IEC 61730-1(Requirements for design and Construction)	-	20000	-
4 IS/IEC 61730-1(Classification, Application and Inteded Use)	-	10000	-
5.6.4 IS/IEC 61730-1(Distance through Insulation)	-	5000	-
5.6.3 IS/IEC 61730-1(Insulation Coordination)	-	10000	-
5.6.2 IS/IEC 61730-1(Protection Agianst accessibility to hazardeous live parts)	-	20000	-
5.6, 5.6.1 IS/IEC 61730-1(Protection Agianst Electric Shock)	-	10000	-
5.5.4 IS/IEC 61730-1(Adhesives)	-	20000	-
5.5.3.2 IS/IEC 61730-1(Current Carrying Parts)	-	10000	-
5.5.3, 5.5.3.1 IS/IEC 61730-1(Metallic materials)	-	10000	-
5.5.2.4 IS/IEC 61730-1(Polymeric Meterial used for Mechanical functions)	-	10000	-
5.5.2.3.5 IS/IEC 61730-1(Polymeric Insulating Parts supporting live Parts)	-	10000	-
5.5.2.3.4 IS/IEC 61730-1(Polymeric Insulating materials used as external Parts)	-	10000	-
5.5.2.3.3 IS/IEC 61730-1(Endurance to thermal stress-RTE (RTI) or TI)	-	35000	-
5.5.2.3.2 IS/IEC 61730-1(Endurance to Electrical Stress)	-	20000	-
5.5.2 IS/IEC 61730-1(Polymeric Materials)	-	20000	-
5.5, 5.5.1 IS/IEC 61730-1(Materials)	-	10000	-
5.4.7 IS/IEC 61730-1(Other Connections)	-	10000	-
5.4.6 IS/IEC 61730-1(Connections by adhesives)	-	10000	-
5.4.5 IS/IEC 61730-1(Form/Press/Tight/Fit)	-	10000	-
5.4.4 IS/IEC 61730-1(Thread Cutting Screws)	-	10000	-
5.4.3 IS/IEC 61730-1(Rivets)	-	10000	-
5.4.2 IS/IEC 61730-1(Screw Connctions)	-	10000	-
5.4, 5.4.1 IS/IEC 61730-1(Mechanical and Electromechanical connections)	-	10000	-
5.3.10 IS/IEC 61730-1(Bypass Diodes)	-	10000	-
5.3.9 IS/IEC 61730-1(Encapsulants)	-	10000	-
5.3.8 IS/IEC 61730-1(Electrical Connections)	-	10000	-
5.3.7 IS/IEC 61730-1(Insulation Barrier)	-	10000	-
5.3.6 IS/IEC 61730-1(Front sheet and back Sheet)	-	10000	-
5.3.5 IS/IEC 61730-1(Junction Box for PV modules)	-	10000	-
5.3.4 IS/IEC 61730-1(Connectors)	-	10000	-
5.3.3 IS/IEC 61730-1(External Wirings and cables)	-	10000	-
5.3.2 IS/IEC 61730-1(Internal Wiring)	-	10000	-
5.3, 5.3.1 IS/IEC 61730-1(Electrical Components and Insualtion)	-	10000	-
5.2 IS/IEC 61730-1(Marking and Documentation)	-	10000	-
5, 5.1 IS/IEC 61730-1(Requirements for design and Construction)	-	10000	-
4 IS/IEC 61730-1(Classification, Application and Inteded Use)	-	10000	-
4(Classification, applications and intended use)	-	10000	-
5.2(Marking and documentation)	-	5000	-
5.3(Electrical components and insulation)	-	10000	-
5.3.2(Internal wiring)	-	10000	-
5.3.4(Connectors)	-	10000	-
5.4(Mechanical and electromechanical connections)	-	10000	-
5.5(Materials)	-	10000	-
5.5.2, 5.3.7(Polymeric materials)	-	10000	-
5.6(Protection against electric shock)	-	10000	-
5.6.3.4(Clearances and creepage distances)	-	5000	-

05 Nov, 2026

-
Included w.e.f 13.05.2025

4130

Planet Electro Labs Private Limited (407)

8174226

IS 14286 : Part 1 : Sec 2 (2023)

Terrestrial photovoltaic PV modules Design qualification and type approval Part 1-2: Special requirements for testing of thin-film Cadmium Telluride CdTe based photovoltaic PV modules Third Revision

2000000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-8(Major visual defects)	-	15000	-
Cl-11.1(Visual inspection)	-	15000	-
Cl-11.2(Maximum power determination)	-	100000	-
Cl-11.3(Insulation tes)	-	20000	-
Cl-11.4(Measurement of temperature coefficients)	-	100000	-
Cl-11.5(Measurement of nominal module operating temperature)	-	100000	-
Cl-11.6(Performance at STC and NMOT)	-	50000	-
Cl-11.7(Performance at low irradiance)	-	100000	-
Cl-11.8(Outdoor exposure test)	-	100000	-
Cl-11.9(Hot-spot endurance test)	-	100000	-
Cl-11.10(UV preconditioning test)	-	50000	-
Cl-11.11(Thermal cycling test)	-	120000	-
Cl-11.12(Humidity-freeze test)	-	120000	-
Cl-11.13(Damp heat test)	-	120000	-
Cl-11.14(Robustness of terminations test)	-	20000	-
Cl-11.15(Wet leakage current test)	-	50000	-
Cl-11.16(Static mechanical load test)	-	50000	-
Cl-11.17(Hail test)	-	75000	-
Cl-11.18(Bypass diode testing)	-	50000	-
Cl-11.19(Stabilization)	-	50000	-
5(Marking and documentation)	-	5000	-
11.20(Cyclic (dynamic) mechanical load test (MQT 20))	-	20000	-
11.21(Potential induced degradation test (MQT 21))	-	350000	-
11.22(Bending test (MQT 22))	-	20000	-

05 Nov, 2026

-
Included w.e.f 13.05.2025

4131

Planet Electro Labs Private Limited (407)

8174226

IS 14286 : Part 1 : Sec 1 (2023)

Terrestrial photovoltaic PV modules Design qualification and type approval Part 1-1: Special requirements for testing of crystalline silicon photovoltaic PV modules Third Revision

2000000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-8(Major visual defects)	-	15000	-
Cl-11.1(Visual inspection)	-	15000	-
Cl-11.2(Maximum power determination)	-	20000	-
Cl-11.3(Insulation test)	-	20000	-
Cl-11.4(Measurement of temperature coefficients)	-	100000	-
Cl-11.5(Measurement of nominal module operating temperature)	-	50000	-
Cl-11.6(Performance at STC)	-	50000	-
Cl-11.7(Performance at low irradiance)	-	100000	-
Cl-11.8(Outdoor exposure test)	-	100000	-
Cl-11.9(Hot-spot endurance test)	-	100000	-
Cl-11.10(UV preconditioning test)	-	80000	-
Cl-11.11(Thermal cycling test)	-	120000	-
Cl-11.12(Humidity-freeze test)	-	120000	-
Cl-11.13(Damp heat test)	-	120000	-
Cl-11.14(Robustness of terminations test)	-	20000	-
Cl-11.15(Wet leakage current tes)	-	50000	-
Cl-11.16(Static mechanical load test)	-	50000	-
Cl-11.17(Hail test)	-	75000	-
Cl-11.18(Bypass diode thermal test)	-	20000	-
Cl-11.19(Stabilization)	-	100000	-
5(Marking and documentation)	-	5000	-
11.20(Cyclic (dynamic) mechanical load test (MQT 20))	-	20000	-
11.21(Potential induced degradation test (MQT 21))	-	400000	-
11.22(Bending test (MQT 22))	-	40000	-

05 Nov, 2026

-
Included w.e.f 13.05.2025

4132

Sleen India Biz venture Private Limited, Agra

9139736

IS 13422 (2024)

Single-use Sterile Rubber Surgical Gloves ï¿½ Specification (First Revision)

‘DISPOSABLE SURGICAL RUBBER GLOVES

10500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5(Materials)	-	500	-
Cl-6(Sampling and selection of test pieces)	-	0	-
Cl-7.1(Dimensions)	-	1000	-
Cl-7.2(Watertightness)	-	2000	-
Cl-7.3(Tensile properties)	-	0	-
Cl-7.3.1(General)	-	0	-
Cl-7.3.2(Force at break and elongation at break before accelerated ageing)	-	2000	-
Cl-7.3.3(Force at break and elongation at break after accelerated ageing)	-	3000	-
Cl-7.3.4(Force required to produce 300 % elongation)	-	2000	-
Cl-9(Marking.)	-	0	-
Cl-5(Materials)	-	0	-
Cl-6(Sampling and selection of test pieces)	-	0	-
Cl-7.1(Dimensions)	-	0	-
Cl-7.2(Watertightness)	-	0	-
Cl-7.3(Tensile properties)	-	0	-
Cl-7.3.1(General)	-	0	-
Cl-7.3.2(Force at break and elongation at break before accelerated ageing)	-	0	-
Cl-7.3.3(Force at break and elongation at break after accelerated ageing)	-	0	-
Cl-7.3.4(Force required to produce 300 % elongation)	-	0	-
Cl-9(Marking.)	-	0	-

15 May, 2027

-
Included w.e.f.23.07.2025 Exclusion Cl-7.4(Sterlity) Cl-5(matarials

4133

Hi Physix Laboratory India Private Limited, Pune

7126926

IS 302 : Part 2 : Sec 45 (1994)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 45 electric heating tools

54000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Rating)	-	0	-
6(Classification)	-	0	-
7(Marking)	-	1000	-
8(Protection against Access to Live Parts)	-	2000	-
9(Starting Of Motor Operated Appliances)	-	0	-
10("Power Input & Current")	-	2000	-
11(Temperature Rise/ Heating)	-	4000	-
12(Operation Under Overload Condition)	-	0	-
13(Electric Insulation at Operating Temperature)	-	3000	-
14("Radio and Television Interference Suppression / Transient Over Voltage ")	-	2000	-
15(Moisture Resistance)	-	4000	-
16(Insulation Resistance and Electric Strength/ Leakage Current and Electric Strength (After Humidity Treatment))	-	3000	-
17(Overload Protection/ Overload Protection of Transformers & Associated Circuits)	-	4000	-
18(Endurance)	-	0	-
19(Abnormal Operation)	-	4000	Charges applicable excluding the test of Cl.19.11.4.1 to Cl.19.11.4.7. The testing charges for EMI/EMC Testing (Cl.19.11.4.1 to Cl.19.11.4.7) will be Rs. 55000 charged extra.
20(Stability & Mechanical Hazards)	-	2000	-
21(Mechanical strength)	-	2000	-
22(Construction)	-	5000	-
23(Internal Wiring)	-	2000	-
24(Components)	-	2000	-
25(Supply Connection & External Flexible Cords)	-	2000	-
26(Terminals For External Conductors)	-	1000	-
27(Provision For Earthing)	-	2000	-
28(Screws & Connections)	-	1000	-
29(Creepage Distances & Clearances)	-	2000	-
30(Resistance to Heat, Fire and Tracking)	-	3000	-
31(Radiation hazards)	-	0	Testing charges included in Cl.XXV of Table 101 (Resistance to Rusting)
XXV of Table 101(Resistance to Rusting)	-	1000	-
4(General Requirement)	-	0	-
19.11.4.7(Harmonics)	-	5000	if applicable
19.11.4.6(Class 3 Voltage dips and interruptions)	-	5000	if applicable
19.11.4.5(Immunity to conducted discharges)	-	10000	if applicable
19.11.4.4(Surge immunity test)	-	5000	if applicable
19.11.4.3(Fast transient bursts)	-	5000	if applicable
19.11.4.2(Radiated fields)	-	20000	if applicable
19.11.4.1(Electrostatic discharges)	-	5000	if applicable

20 Jun, 2028

-
Included w.e.f 25.03.2025 Exclusion Cl 24 (Components)

4134

Planet Electro Labs Private Limited (407)

8174226

IS 14286 : Part 1 (2023)

Terrestrial Photovoltaic PV Modules Design Qualification and Type Approval Part 1: Test Requirements (Third Revision)

2000000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Visual inspection (MQT 01))	-	15000	-
4.2(Maximum power determination (MQT 02))	-	100000	-
4.3(Insulation test (MQT 03))	-	25000	-
4.4(Measurement of temperature coefficients (MQT 04))	-	70000	-
4.6(Performance at STC (MQT 06.1))	-	100000	-
4.7(Performance at low irradiance (MQT 07))	-	70000	-
4.8(Outdoor exposure test (MQT 08))	-	80000	-
4.9(Hot-spot endurance test (MQT 09))	-	70000	-
4.10(UV preconditioning test (MQT 10))	-	100000	-
4.11(Thermal cycling test (MQT 11))	-	200000	-
4.12(2 Humidity-freeze test (MQT 12))	-	120000	-
4.13(Damp heat test (MQT 13))	-	125000	-
4.14(Robustness of terminations (MQT 14))	-	25000	-
4.15(5 Wet leakage current test (MQT 15))	-	40000	-
4.16(Static mechanical load test (MQT 16))	-	60000	-
4.17(Hail test (MQT 17))	-	75000	-
4.18(Bypass diode testing (MQT 18))	-	50000	-
4.19(Stabilization (MQT 19))	-	100000	-
4.20(Cyclic (dynamic) mechanical load test (MQT 20))	-	40000	-
4.21(Potential induced degradation test (MQT 21))	-	435000	-
4.22(Bending test (MQT 22))	-	50000	-
4.1(Visual inspection (MQT 01))	-	5000	-
4.2(Maximum power determination (MQT 02))	-	10000	-
4.3(Insulation test (MQT 03))	-	10000	-
4.4(Measurement of temperature coefficients (MQT 04))	-	75000	-
4.6(Performance at STC (MQT 06.1))	-	75000	-
4.7(Performance at low irradiance (MQT 07))	-	100000	-
4.8(Outdoor exposure test (MQT 08))	-	100000	-
4.9(Hot-spot endurance test (MQT 09))	-	100000	-
4.10(UV preconditioning test (MQT 10))	-	100000	-
4.11(Thermal cycling test (MQT 11))	-	125000	-
4.12(2 Humidity-freeze test (MQT 12))	-	125000	-
4.13(Damp heat test (MQT 13))	-	125500	-
4.14(Robustness of terminations (MQT 14))	-	10000	-
4.15(5 Wet leakage current test (MQT 15))	-	40000	-
4.16(Static mechanical load test (MQT 16))	-	40000	-
4.17(Hail test (MQT 17))	-	75000	-
4.18(Bypass diode testing (MQT 18))	-	50000	-
4.19(Stabilization (MQT 19))	-	80000	-
4.20(Cyclic (dynamic) mechanical load test (MQT 20))	-	40000	-
4.21(Potential induced degradation test (MQT 21))	-	400000	-
4.22(Bending test (MQT 22))	-	30000	-
4.5(Placeholder section, formerly NMOT)	-	5000	-

05 Nov, 2026

-
Included w.e.f 13.05.2025

4135

Conformity Testing Labs Pvt. Ltd. Unit 2 (A33)

8139626

IS 17625 : Part 2 : Sec 69 (2021)

Medical Electrical Equipment Part 2 Particular Requirements for Basic Safety and Essential Performance Section 69 Oxygen Concentrator Equipment

950000 View breakup
-

Clause No.	Exclusion	Remark
201.4(Power and Current)	-	-
201.5(Temperature, Humidity, Dimensions, Force)	-	-
201.7.1.2(Legibility of markings)	-	-
201.8(Current, Voltage, Energy, Dimensions, Impedance)	-	-
201.9(Mechanical dimensions, strength , torque, force)	-	-
201.9.6.2.1.101(Additional requirements for audible acoustic energy)	-	-
201.11(Protection against excessive temperatures and other HAZARDS)	-	-
201.11.1(Maximum temperature during NORMAL USE)	-	-
"201.11. 1.2.2"(APPLIED PARTS not intended to supply heat to a PATIENT)	-	-
201.11.2.101(Additional requirements for fire prevention)	-	-
201.11.6.7(Leakage currents , dielectirc strength)	-	-
"201.11. 8.101"()	-	-
201.11.8.101.1(TECHNICAL ALARM CONDITION for power supply failure)	-	-
201.11.8.101.2(INTERNAL ELECTRICAL POWER SOURCE)	-	-
201.12(Accuracy of controls and instruments and protection against hazardous outputs)	-	-
"201.12. 1"(Legibility of markings)	-	-
201.12.1.101(Flowrate control)	-	-
201.12.1.103(Accuracy of concentration)	-	-
201.12.1.104(Outlet pressure)	-	-
201.12.4.4.101.2(Indication of start-up period)	-	-
201.12.4.102(Low oxygen concentration ALARM CONDITION)	-	-
201.13(HAZARDOUS SITUATIONS and fault conditions)	-	-
201.13.2.101(Additional specific SINGLE FAULT CONDITIONS)	-	-
201.15(Mechanical strength, Temperature, current)	-	-
201.16(Leakage currents , dielectirc strength)	-	-
201.17(Electromagnetic compatibility)	-	-
201.102.3(Fire RISK reduction in ACCESSORIES)	-	-
202(Electromagnetic disturbances - Requirements and tests)	-	-
211(Temperature, humidity, altitude, IP, Vibration, Mechanical shock)	-	-
201.7(ME equipment identification, marking and documents)	-	-
201.10(Protection against unwanted and excessive radiaton hazards)	-	-
201.12.4.103(Filter for the delivered gas)	-	-
201.12.4.4.101.1(Flowrate control)	-	-
201.12.1.102(Accuracy of triggered flow)	-	-
201.11.7(Biocompatibility of ME equipment and ME systems)	-	-
12.11.6.6(Cleaning and disinfection of ME equipment or ME system)	-	-
201.11.3.101(Additional requirements for fire enclosures of ME equipment)	-	-
201.6(Classification of ME equipment and ME systems)	-	-
201.6(General requirements)	-	-
201.5(General requirements for testing of ME equipment)	-	-
201.4(General requirements)	-	-
201.7(ME equipment identification, marking and documents)	-	-
201.8(Protection against electrical hazards from ME equipment)	-	-
201.9(Protection against mechanical hazards of ME equipment and ME systems)	-	-
201.1(Protection against unwanted and excessive radiation hazards)	-	-
201.11(Protection against excessive temperatures and other hazards)	-	-
201.12(Accuracy of controls and instruments and protection against hazardous outputs)	-	-
201.13(Hazardous situations and fault conditions for ME equipment)	-	-
201.14(Programmable electrical medical systems (PEMS))	-	-
201.14(Programmable electrical medical systems (PEMS))	-	-
201.16(ME systems)	-	-
201.17(Electromagnetic compatibility of ME equipment and ME systems)	-	-
201.101(Outlet connector)	-	-
201.102(Requirements for parts and accessories)	-	-
201.103(Functional connection)	-	-
201.104(Indication of duration of operation)	-	-
201.105(Integrated conserving equipment function)	-	-
202(Electromagnetic disturbances – Requirements and tests)	-	-
211(Requirements for medical electrical equipment and medical electrical systems used in the home healthcare environment)	-	-

05 Apr, 2027

-
Included w.e.f 25.03.2025 Exclusion: Cl 201.17 (Electromagnetic compatibility)(Radiated emission, Conducted & Radiated susceptibility), Cl 202 (Electromagnetic disturbances - Requirements and tests)(Radiated emission, Conducted & Radiated susceptibility)

4136

Hi Physix Laboratory India Private Limited, Pune

7126926

IS 302 : Part 2 : Sec 12 (1993)

Safety of household and similar electrical appliances - Specification: Part 2 particular requirements: Sec 12 warming plates and similar appliances

56000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Rating)	-	0	-
6(Classification)	-	0	-
7(Marking)	-	1000	-
8(Protection against Access to Live Parts)	-	2000	-
9(Starting Of Motor Operated Appliances)	-	0	-
10("Power Input & Current")	-	2000	-
11(Temperature Rise/ Heating)	-	4000	-
12(Operation Under Overload Conditions of Appliances with heating Element)	-	0	-
13(Leakage Current and Electric Strength at Operating Temperature)	-	3000	-
14("Radio and Television Interference Suppression / Transient Over Voltage ")	-	2000	-
15(Moisture Resistance)	-	4000	-
16(Insulation Resistance and Electric Strength/ Leakage Current and Electric Strength)	-	3000	-
17(Overload Protection/ Overload Protection of Transformers & Associated Circuits)	-	4000	-
18(Endurance)	-	0	-
19(Abnormal Operation)	-	5000	Charges applicable excluding the test of Cl.19.11.4.1 to Cl.19.11.4.7. The testing charges for EMI/EMC Testing (Cl.19.11.4.1 to Cl.19.11.4.7) will be Rs. 55000 charged extra.
20(Stability & Mechanical Hazards)	-	2000	-
21(Mechanical strength)	-	2000	-
22(Construction)	-	5000	-
23(Internal Wiring)	-	2000	-
24(Components)	-	3000	-
25(Supply Connection & External Flexible Cords)	-	2000	-
26(Terminals For External Conductors)	-	1000	-
27(Provision For Earthing)	-	2000	-
28(Screws & Connections)	-	1000	-
29(Clearances, Creepage Distances & Solid Insulation)	-	2000	-
30(Resistance to Heat & Fire)	-	3000	-
31(Resistance to Rusting)	-	1000	-
32(Radiation hazards)	-	0	-
5(Rating)	-	0	-
6(Classification)	-	0	-
7(Marking)	-	0	-
8(Protection against Access to Live Parts)	-	0	-
9(Starting Of Motor Operated Appliances)	-	0	-
10("Power Input & Current")	-	0	-
11(Temperature Rise/ Heating)	-	0	-
12(Operation Under Overload Conditions of Appliances with heating Element)	-	0	-
13(Leakage Current and Electric Strength at Operating Temperature)	-	0	-
14("Radio and Television Interference Suppression / Transient Over Voltage ")	-	0	-
15(Moisture Resistance)	-	0	-
16(Insulation Resistance and Electric Strength/ Leakage Current and Electric Strength)	-	0	-
17(Overload Protection/ Overload Protection of Transformers & Associated Circuits)	-	0	-
18(Endurance)	-	0	-
19(Abnormal Operation)	-	0	-
20(Stability & Mechanical Hazards)	-	0	-
21(Mechanical strength)	-	0	-
22(Construction)	-	0	-
23(Internal Wiring)	-	0	-
24(Components)	-	0	-
25(Supply Connection & External Flexible Cords)	-	0	-
26(Terminals For External Conductors)	-	0	-
27(Provision For Earthing)	-	0	-
28(Screws & Connections)	-	0	-
29(Clearances, Creepage Distances & Solid Insulation)	-	0	-
30(Resistance to Heat & Fire)	-	0	-
31(Resistance to Rusting)	-	0	-
32(Radiation hazards)	-	0	-
19.11.4.1(Electrostatic discharges)	-	5000	If applicable
19.11.4.2(Radiated fields)	-	20000	If applicable
19.11.4.3(Fast transient bursts)	-	5000	If applicable
19.11.4.4(Surge immunity test)	-	5000	If applicable
19.11.4.5(Immunity to conducted discharges)	-	10000	If applicable
19.11.4.6(Class 3 Voltage dips and interruptions)	-	5000	If applicable
19.11.4.7(Harmonics)	-	5000	If applicable

20 Jun, 2028

-
Included w.e.f.20.05.2025 Exclusion Cl. No. 22.32 Rubber parts test 24 (Components)

4137

BIS, Eastern Regional Laboratory (ERL)

None

IS 10258 : Part 1 (2022)

Sterile hypodermic syringes for single use Part 1: Syringes for manual use Third Revision

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.2 (Limits of acidity or alkalinity, unit)	-
Cl. 6.3 (Difference in content of Distilled water(Pb, Sn, Zn & Fe), mg/kg, Max)	-
Cl. 6.3 (Cadmium, mg/kg, Max)	-
6.1 (General)	-
Cl. 6.3 (Difference in content of Distilled water(Pb, Sn, Zn & Fe), mg/kg, Max)	-

-
Except Cl.7

4138

Bharat Test House Pvt. Ltd. 1668 Sonipat

9168306

IS 1361 (1978)

Specification for Steel Windows for Industrial Buildings

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No.3(HANDING)	-	1000	-
Cl. No.4(DESIGNATION)	-	1000	-
Cl. No.5(STANDARD SIZES AND TOLERANCES)	-	2000	-
Cl. No.6(MATERIAL)	-	10000	-
Cl. No.7(CONSTRUCTION)	-	1000	-
Cl. No.8(HOLES FOR FIXING, COUPLING AND GLAZING)	-	1000	-
Cl. No.9(FITTINGS AND FIXING MATERIALS)	-	1000	-
Cl. No.10(COMPOSITE WINDOWS)	-	1000	-
Cl. No.11, Table no. 1(GLASS)	-	4000	-
Cl. No.12(FINISH)	-	1000	-
Cl. No.3(HANDING)	-	1000	-
Cl. No.4(DESIGNATION)	-	0	-
Cl. No.5(STANDARD SIZES AND TOLERANCES)	-	0	-
Cl. No.6(MATERIAL)	-	0	-
Cl. No.7(CONSTRUCTION)	-	0	-
Cl. No.8(HOLES FOR FIXING, COUPLING AND GLAZING)	-	0	-
Cl. No.9(FITTINGS AND FIXING MATERIALS)	-	0	-
Cl. No.10(COMPOSITE WINDOWS)	-	0	-
Cl. No.11, Table no. 1(GLASS)	-	0	-
Cl. No.12(FINISH)	-	0	-
Cl. No.3(HANDING)	-	0	-
Cl. No.4(DESIGNATION)	-	0	-
Cl. No.5(STANDARD SIZES AND TOLERANCES)	-	0	-
Cl. No.6(MATERIAL)	-	0	-
Cl. No.7(CONSTRUCTION)	-	0	-
Cl. No.8(HOLES FOR FIXING, COUPLING AND GLAZING)	-	0	-
Cl. No.9(FITTINGS AND FIXING MATERIALS)	-	0	-
Cl. No.10(COMPOSITE WINDOWS)	-	0	-
Cl. No.11, Table no. 1(GLASS)	-	0	-
Cl. No.12(FINISH)	-	0	-

26 Jul, 2027

-
Included w.e.f.19.05.2025

4139

SHRI KRISHNA TEST HOUSE PVT LTD (142)

8185606

IS 18755 (2024)

Tri-ply SS-AL-SS material used for manufacture of utensils and kitchen appliances Specification

All Grades/ Types

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(Supply of material and designation)	-	15000	-
Cl-5(Manufacturer)	-	15000	-
Cl-6(Aluminium for use as matrix)	-	15000	-
Cl-6(Top-surface of the aluminium matrix)	-	15000	-
Cl-6(Bottom-surface of the aluminium matrix)	-	15000	-
Cl-7.1.1(Tensile properties)	-	15000	-
Cl-7.1.1(Apparent Yield Strength)	-	15000	-
Cl-7.1.1(Tensile Strength Mpa,)	-	15000	-
Cl-7.1.2(Test Specimen)	-	15000	-
Cl-7.1.3(Test Parameters)	-	15000	-
Cl-7.2.1(Bond strength of Tri-Ply)	-	15000	-
Cl-7.2.2(Sample Preparation and Test Specimen)	-	15000	-
Cl-7.2.3(Test Apparatus)	-	15000	-
Cl-7.2.4(Procedure)	-	15000	-
Cl-8.1(Sample of suitable size)	-	15000	-
Cl-8.2(specimen for peel strength)	-	15000	-
Cl-8.3, table-3(T-Peel Strength, N/mm, Min SS304 and Al 19500 interface)	-	15000	-
Cl-8.3, table-3(T-Peel Strength, N/mm, Min SS430 and Al 19500 interface)	-	15000	-
Cl-9.1(Thickness)	-	15000	-
Cl-9.2(Diameter)	-	15000	-
Cl-9.3(Flatness)	-	15000	-
Cl-10(surface finish)	-	15000	-
Cl-11(Workmanship, finish and appearance)	-	15000	-
Cl-14(Marking)	-	15000	-

13 May, 2028

-
-

4140

SHRI KRISHNA TEST HOUSE PVT LTD (142)

8185606

IS 319 (2007)

Free cutting brass bars, rods and section - Specification (Fifth Revision)

ALL GRADES

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.0(Freedom from defects)	-	6000	-
7.0(Dimension and Tolerances)	-	6000	-
8.1 Table 1(Cu)	-	6000	-
8.1 Table 1(Pb)	-	6000	-
8.1 Table 1(Fe)	-	6000	-
8.1 Table 1(Total other impurities excluding iron)	-	6000	-
8.1 Table 1(Zn)	-	6000	-
9.1 Table-2(Tensile Strength)	-	6000	-
9.1 Table-2(Elongation)	-	6000	-
9.2(Vickers Hardness)	-	6000	-
10.1(Mercurous Nitrate Test)	-	6000	-
14(Marking)	-	6000	-

13 May, 2028

-
-

Bureau of Indian Standards

The National Standards Body of India

Search by IS Number