BIS - LIMS (Laboratory Information Management System)

Search by IS Number

Reset

15623 Results

S.No.

Lab Name

Osl Code

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

6961

Bahadurgarh Footwear Development Services (BFDS), Bahadurgarh

8168806

IS 6721 (2023)

SANDAL AND SLIPPERS SPECIFICATION First revision

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No.4(SHAPE AND DESIGN)	-	200	-
Cl. No.5("SIZE AND FITTINGS ")	-	200	-
Cl. No.6("CONSTRUCTION ")	-	200	-
Cl. No.7(MATERIAL)	-	200	-
Cl. No.8.1, Table no. 1(i),a("Tear strength, (other than moulded upper material) ")	-	450	-
Cl. No.8.1, Table no. 1(i),b("For all moulded upper material ")	-	450	-
Cl. No.8.1, Table no. 1(ii)(Flexing endurance)	-	600	-
Cl. No.8.2,Table no. 2(i)(Tear strength)	-	450	-
Cl. No.8.2,Table no. 2(ii),a("Abrasion resistance- At dry condition")	-	600	-
Cl. No.8.2,Table no. 2(ii),b("Abrasion resistance- At wet condition")	-	600	-
Cl. No.8.3,Table no. 3(i)(Tear strength)	-	450	-
Cl. No.8.3,Table no. 3(ii),a("Abrasion resistance- At dry condition")	-	600	-
Cl. No.8.3,Table no. 3(ii),b("Abrasion resistance- At wet condition")	-	600	-
Cl. No.8.4,Table no. 4(i)(Grain crack index)	-	500	-
Cl. No.8.4,Table no. 4(ii)(Density)	-	200	-
Cl. No.8.4,Table no. 4(iii)(Abrasion resistance)	-	600	-
Cl. No.8.4,Table no. 5(i)(Density)	-	200	-
Cl. No.8.4,Table no. 5(ii)("Abrasion resistance, Volume loss ")	-	600	-
Cl. No.8.4, Table no. 5(iii)("Flexing resistance, At 30 000 flexes")	-	600	-
Cl. No.8.5, Table no. 6(i)("Bond strength, N/mm, Min (Applicable when fore part is fully covered or strap width is more than 25 mm)")	-	500	-
Cl. No.8.5, Table no. 6(ii)("Toe post attachment strength, N, Min (Applicable if toe post is present)")	-	500	-
Cl. No.8.5, Table no. 6(iii)("Toe ring attachment strength, Min (Applicable if toe ring is not integral part of upper")	-	500	-
Cl. No.8.5, Table no. 6(iv)(Strap to outsole strength)	-	500	-
Cl. No.8.5, Table no. 6(v)("Attachment strength of back strap and Buckle/D-ring ")	-	500	-
Cl. No.8.5, Table no. 6(vi)("Attachment strength of elastic, limit of useful extension, percent")	-	500	-
Cl. No.8.5, Table no. 6(vii)("Attachment strength of back strap and velcro, N, Min (If, present)")	-	500	-
Cl. No.8.5, Table no. 6(viii)("Hydrolysis resistance, Cut growth after 150 000 flexes, mm, Max (Applicable for PU sole only)")	-	2000	-
Cl. No.8.5, Table no. 6(ix)("Heel pull off strength, N, Min (Applicable for heel height 40 mm and above attached separately to the sandal/slipper)")	-	500	-
Cl. No.8.5, Table no. 6(x)("Inter layer bond strength, N/mm, (Applicable for multi-layer sole)")	-	500	-
Cl. No.8.5, Table no. 6(xi)("Slip Resistance, Coefficient of Friction (COF) (Not applicable for leather sole) (To be carried out on quarry tiles)")	-	1200	-
Cl. No.9.(MARKING AND PACKING)	-	500	-

02 Sep, 2027

-
Exclusion: Table 1 xiv Chemical requirement and Table 1 xv Lead content

6962

Bahadurgarh Footwear Development Services (BFDS), Bahadurgarh

8168806

IS 10702 (2023)

Hawai Chappal-Specification

6500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Material)	-	200	-
4.2(Length)	-	200	-
4.3(Thickness)	-	200	-
4.4 , Table No. 1 , i)(Density)	-	200	-
4.4 , Table No. 1 , ii)(2Compression set at constant stress)	-	500	-
4.4 , Table No. 1 , iii)(3Split tear strength)	-	450	-
4.4 , Table No. 1 , iv)("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber")	-	600	-
4.4 , Table No. 1 , v)(5Abrasion resistance at applied force)	-	600	-
4.4 , Table No. 1 , vi)(Flexing resistance: Maximum cut growth at 50 000 flexes)	-	600	-
4.4 , Table No. 1 , vii)(7 Hydrolysis resistance, Maximum cut growth at 50 000 flexes)	-	2000	-
4.4 , Table No . 2 , i)(Density , Solid strap, Cellular strap)	-	200	-
4.4 , Table No . 2 , ii)("Breaking strength , Strap to strap and Toe portion to strap , Elongation at break")	-	450	-
4.4 , Table No . 2 , iii)(Minimum cross section of the stud)	-	500	-
4.4 , Table No . 2 , iv)(Stud bolt)	-	200	-
4.4 , Table No . 3 , i)(Toe post attachment strength)	-	500	-
4.4 , Table No . 3 , ii)(Attachment strength of rear strap)	-	500	-
4.4 , Table No . 3 , iii)(Inter layer bond strength)	-	500	-
6(MARKING AND PACKING)	-	500	-
Cl. No.5.1,Table no.1 of IS 17011(iv)(Chromium (VI))	-	600	-
Cl. No.5.1,Table no.1 of IS 17011(x)(pH)	-	400	-
Clause 4.1 - 4.1.1(Bottom Material)	-	200	-
Clause 4.1 - 4.1.2(Strap Material)	-	200	-
Clause 4.1 - 4.1.4(Material)	-	200	-
Clause 4.2(Material)	-	200	-
Clause 4.3 - 4.3.1(Thickness)	-	200	-
Clause 4.3 - 4.3.2(Thickness)	-	200	-
Clause 4.4 Table 1 -i)(Density, g/cm3, Min)	-	200	-
Clause 4.4 Table 2 -i) - b(Density, g/cm3 Cellular strap)	-	200	-
Clause 4.4 Table 1 -iii)(Split tear strength, kg, Min)	-	450	-
Clause 4.4 Table 1 -iv) - a("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, percent, Max")	-	600	-
Clause 4.4 Table 1 -iv) - b(Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber, percent, Max)	-	600	-
Clause 4.4 Table 1 -v)(Abrasion resistance at applied force 5 N)	-	600	-
Clause 4.4 Table 2 -i) - a("Density, g/cm3 Solid strap ")	-	200	-
Clause 4.4 Table 2 -ii) - a - 1("Breaking strength, kgf, Min Strap to strap(Solid Strap)")	-	450	-
Clause 4.4 Table 2 -ii) - a - 2("Breaking strength, kgf, Min Strap to strap(Cellular Strap)")	-	450	-
Clause 4.4 Table 2 -ii) - a - 3("Breaking strength, kgf, Min Toe portion to strap(Solid Strap)")	-	450	-
Clause 4.4 Table 2 -ii) - a - 4("Breaking strength, kgf, Min Toe portion to strap(Cellular Strap)")	-	450	-
Clause 4.4 Table 2 -ii) - b - 1("Elongation at break, percent (Applicable to strap to strap (V shape) Solid Strap")	-	450	-
Clause 4.4 Table 2 -ii) - b - 2("Elongation at break, percent (Applicable to strap to strap (V shape) Cellular Strap")	-	450	-
Clause 4.4 Table 2 -iii) - a("Minimum cross section of the stud, mm, Size 1 to 13 (Adult)")	-	200	-
Clause 4.4 Table 2 -iii) - b("Minimum cross section of the stud, mm, Size 3 to 13 (Children)")	-	200	-
Clause 4.4 Table 2 -iv) - a("Stud bolt, mm Diameter/edge to edge length")	-	200	-
Clause 4.4 Table 2 -iv) - b("Stud bolt, mm Thickness")	-	200	-
Clause 4.4 Table 3 -i)("Toe post attachment strength, N, Min")	-	450	-
Clause 4.4 Table 3 -iii)("Inter layer bond strength, N/mm, Min")	-	500	-
Clause 4.1 - 4.1.3(Material)	-	200	-
Clause 4.4 Table 3 -ii)("Attachment strength of rear strap, N, Min")	-	450	-
4.1(Material)	-	200	-
4.2(Length)	-	200	-
4.3(Thickness)	-	200	-
4.4 , Table No. 1 , i)(Density)	-	200	-
4.4 , Table No. 1 , ii)(2Compression set at constant stress)	-	500	-
4.4 , Table No. 1 , iii)(3Split tear strength)	-	450	-
4.4 , Table No. 1 , iv)("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber")	-	600	-
4.4 , Table No. 1 , v)(5Abrasion resistance at applied force)	-	600	-
4.4 , Table No. 1 , vi)(Flexing resistance: Maximum cut growth at 50 000 flexes)	-	600	-
4.4 , Table No. 1 , vii)(7 Hydrolysis resistance, Maximum cut growth at 50 000 flexes)	-	2000	-
4.4 , Table No . 2 , i)(Density , Solid strap, Cellular strap)	-	200	-
4.4 , Table No . 2 , ii)("Breaking strength , Strap to strap and Toe portion to strap , Elongation at break")	-	500	-
4.4 , Table No . 2 , iii)(Minimum cross section of the stud)	-	200	-
4.4 , Table No . 2 , iv)(Stud bolt)	-	200	-
4.4 , Table No . 3 , i)(Toe post attachment strength)	-	500	-
4.4 , Table No . 3 , ii)(Attachment strength of rear strap)	-	500	-
4.4 , Table No . 3 , iii)(Inter layer bond strength)	-	500	-
6(MARKING AND PACKING)	-	200	-
Cl. No.5.1,Table no.1 of IS 17011(iv)(Chromium (VI))	-	800	-
Cl. No.5.1,Table no.1 of IS 17011(x)(pH)	-	500	-
Clause 4.1 - 4.1.1(Bottom Material)	-	200	-
Clause 4.1 - 4.1.2(Strap Material)	-	200	-
Clause 4.1 - 4.1.4(Material)	-	200	-
Clause 4.2(Material)	-	200	-
Clause 4.3 - 4.3.1(Thickness)	-	200	-
Clause 4.3 - 4.3.2(Thickness)	-	200	-
Clause 4.4 Table 1 -i)(Density, g/cm3, Min)	-	200	-
Clause 4.4 Table 2 -i) - b(Density, g/cm3 Cellular strap)	-	200	-
Clause 4.4 Table 1 -iii)(Split tear strength, kg, Min)	-	450	-
Clause 4.4 Table 1 -iv) - a("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, percent, Max")	-	600	-
Clause 4.4 Table 1 -iv) - b(Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber, percent, Max)	-	600	-
Clause 4.4 Table 1 -v)(Abrasion resistance at applied force 5 N)	-	600	-
Clause 4.4 Table 2 -i) - a("Density, g/cm3 Solid strap ")	-	200	-
Clause 4.4 Table 2 -ii) - a - 1("Breaking strength, kgf, Min Strap to strap(Solid Strap)")	-	500	-
Clause 4.4 Table 2 -ii) - a - 2("Breaking strength, kgf, Min Strap to strap(Cellular Strap)")	-	500	-
Clause 4.4 Table 2 -ii) - a - 3("Breaking strength, kgf, Min Toe portion to strap(Solid Strap)")	-	500	-
Clause 4.4 Table 2 -ii) - a - 4("Breaking strength, kgf, Min Toe portion to strap(Cellular Strap)")	-	500	-
Clause 4.4 Table 2 -ii) - b - 1("Elongation at break, percent (Applicable to strap to strap (V shape) Solid Strap")	-	450	-
Clause 4.4 Table 2 -ii) - b - 2("Elongation at break, percent (Applicable to strap to strap (V shape) Cellular Strap")	-	450	-
Clause 4.4 Table 2 -iii) - a("Minimum cross section of the stud, mm, Size 1 to 13 (Adult)")	-	200	-
Clause 4.4 Table 2 -iii) - b("Minimum cross section of the stud, mm, Size 3 to 13 (Children)")	-	200	-
Clause 4.4 Table 2 -iv) - a("Stud bolt, mm Diameter/edge to edge length")	-	200	-
Clause 4.4 Table 2 -iv) - b("Stud bolt, mm Thickness")	-	200	-
Clause 4.4 Table 3 -i)("Toe post attachment strength, N, Min")	-	500	-
Clause 4.4 Table 3 -iii)("Inter layer bond strength, N/mm, Min")	-	500	-
Clause 4.1 - 4.1.3(Material)	-	200	-
Clause 4.4 Table 3 -ii)("Attachment strength of rear strap, N, Min")	-	500	-
4.4 , Table No. 1 , vi)(Flexing resistance: Maximum cut growth at 50 000 flexes)	-	800	-
4.4 , Table No. 1 , vii)(7 Hydrolysis resistance, Maximum cut growth at 50 000 flexes)	-	2500	-
4.4 , Table No . 2 , ii)("Breaking strength , Strap to strap and Toe portion to strap , Elongation at break")	-	450	-
6(MARKING AND PACKING)	-	500	-
Clause 4.4 Table 1 -iv) - a("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, percent, Max")	-	800	-
Clause 4.4 Table 1 -iv) - b(Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber, percent, Max)	-	800	-
Clause 4.4 Table 2 -ii) - b - 1("Elongation at break, percent (Applicable to strap to strap (V shape) Solid Strap")	-	500	-
Clause 4.4 Table 2 -ii) - b - 2("Elongation at break, percent (Applicable to strap to strap (V shape) Cellular Strap")	-	500	-
Clause 4.4 Table 2 -iii) - a("Minimum cross section of the stud, mm, Size 1 to 13 (Adult)")	-	500	-
Clause 4.4 Table 2 -iii) - b("Minimum cross section of the stud, mm, Size 3 to 13 (Children)")	-	500	-
Clause 4.4 Table 2 -iv) - a("Stud bolt, mm Diameter/edge to edge length")	-	500	-
Cl-4 ((Amendment No-1)(Category And Type)	-	200	-
Cl-4.4, Table -1 S. No-1 (i) (Amendment No-1)(Compression set at constant stress)	-	500	-
Cl-4.4, Table -1 S. No-1 (ii) (Amendment No-1)(Split tear strength)	-	450	-
Cl-4.4, Table -1 S. No-1 (iii) (a)(Amendment No-1)("Shrinkage at Shrinkage at 50 °C ± 1 °C for 2 h for polymeric material, percent, Max ")	-	800	-
Cl-4.4, Table -1 S. No-1 (iii)(b) (Amendment No-1)(Shrinkage at 100 °C ± 1 °C for 1 h for rubber, percent, Max)	-	800	-
Cl-4.4, Table -1 S. No-1 (iv) (Amendment No-1)(Abrasion resistance at applied force)	-	600	-
Cl-4.4, Table -1 S. No-1 (v) (Amendment No-1)(Flexing resistance: Maximum cut growth,)	-	600	-
Cl-4.4, Table -1 S. No-1 (vi) (Amendment No-1)(Hydrolysis resistance:Maximum cut growth)	-	2500	-
Cl-4.4, Table -2 S. No-1 (i), a (Amendment No-1)("Breaking strength for Strap to strap 1-Solid strap 2-Cellular strap")	-	500	-
Cl-4.4, Table -2 S. No-1 (i), b (Amendment No-1)("Breaking strength for Toe portion to strap 1-Solid strap 2-Cellular strap")	-	500	-
Cl-4.4, Table -2 S. No-1 (i), c (Amendment No-1)("Elongation at break , percent, Min 1-Solid strap 2-Cellular strap")	-	450	-
Cl-4.4, Table -3 S. No-1 (i), (Amendment No-1)(Toe post attachment strength)	-	500	-
Cl-4.4, Table -3 S. No-1 (ii), (Amendment No-1)(Attachment strength of rear strap)	-	500	-
Cl-4.4, Table -3 S. No-1 (iii), (Amendment No-1)(Inter layer bond strength)	-	500	-
4.4 , Table No. 1 , iv)("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber")	-	800	-
Clause 4.4 Table 2 -ii) - a - 1("Breaking strength, kgf, Min Strap to strap(Solid Strap)")	-	450	-
Clause 4.4 Table 2 -ii) - a - 2("Breaking strength, kgf, Min Strap to strap(Cellular Strap)")	-	450	-
Clause 4.4 Table 2 -ii) - a - 3("Breaking strength, kgf, Min Toe portion to strap(Solid Strap)")	-	450	-
Clause 4.4 Table 2 -ii) - a - 4("Breaking strength, kgf, Min Toe portion to strap(Cellular Strap)")	-	450	-
Clause 4.4 Table 3 -ii)("Attachment strength of rear strap, N, Min")	-	450	-
Cl-4 ((Amendment No-1)(Category And Type)	-	450	-
Cl-4.4, Table -1 S. No-1 (i) (Amendment No-1)(Compression set at constant stress)	-	500	-
Cl-4.4, Table -1 S. No-1 (ii) (Amendment No-1)(Split tear strength)	-	450	-
Cl-4.4, Table -1 S. No-1 (iii) (a)(Amendment No-1)("Shrinkage at Shrinkage at 50 °C ± 1 °C for 2 h for polymeric material, percent, Max ")	-	800	-
Cl-4.4, Table -1 S. No-1 (iii)(b) (Amendment No-1)(Shrinkage at 100 °C ± 1 °C for 1 h for rubber, percent, Max)	-	800	-
Cl-4.4, Table -1 S. No-1 (iv) (Amendment No-1)(Abrasion resistance at applied force)	-	600	-
Cl-4.4, Table -1 S. No-1 (v) (Amendment No-1)(Flexing resistance: Maximum cut growth,)	-	800	-
Cl-4.4, Table -1 S. No-1 (vi) (Amendment No-1)(Hydrolysis resistance:Maximum cut growth)	-	2500	-
Cl-4.4, Table -2 S. No-1 (i), a (Amendment No-1)("Breaking strength for Strap to strap 1-Solid strap 2-Cellular strap")	-	450	-
Cl-4.4, Table -2 S. No-1 (i), b (Amendment No-1)("Breaking strength for Toe portion to strap 1-Solid strap 2-Cellular strap")	-	450	-
Cl-4.4, Table -2 S. No-1 (i), c (Amendment No-1)("Elongation at break , percent, Min 1-Solid strap 2-Cellular strap")	-	450	-
Cl-4.4, Table -3 S. No-1 (i), (Amendment No-1)(Toe post attachment strength)	-	500	-
Cl-4.4, Table -3 S. No-1 (ii), (Amendment No-1)(Attachment strength of rear strap)	-	450	-
Cl-4.4, Table -3 S. No-1 (iii), (Amendment No-1)(Inter layer bond strength)	-	500	-
4.4 , Table No . 2 , iii)(Minimum cross section of the stud)	-	500	-
Clause 4.1 - 4.1.2(Strap Material)	-	450	-
Clause 4.4 Table 2 -iii) - a("Minimum cross section of the stud, mm, Size 1 to 13 (Adult)")	-	450	-
Clause 4.4 Table 2 -iii) - b("Minimum cross section of the stud, mm, Size 3 to 13 (Children)")	-	450	-
Cl-4 ((Amendment No-1)(Category And Type)	-	200	-
Cl-4.4, Table -1 S. No-1 (v) (Amendment No-1)(Flexing resistance: Maximum cut growth,)	-	600	-
Cl-4.4, Table -3 S. No-1 (ii), (Amendment No-1)(Attachment strength of rear strap)	-	500	-
4.1(Material)	-	-	-
4.2(Length)	-	-	-
4.3(Thickness)	-	-	-
4.4 , Table No. 1 , i)(Density)	-	-	-
4.4 , Table No. 1 , ii)(2Compression set at constant stress)	-	-	-
4.4 , Table No. 1 , iii)(3Split tear strength)	-	-	-
4.4 , Table No. 1 , iv)("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber")	-	-	-
4.4 , Table No. 1 , v)(5Abrasion resistance at applied force)	-	-	-
4.4 , Table No. 1 , vi)(Flexing resistance: Maximum cut growth at 50 000 flexes)	-	-	-
4.4 , Table No. 1 , vii)(7 Hydrolysis resistance, Maximum cut growth at 50 000 flexes)	-	-	-
4.4 , Table No . 2 , i)(Density , Solid strap, Cellular strap)	-	-	-
4.4 , Table No . 2 , ii)("Breaking strength , Strap to strap and Toe portion to strap , Elongation at break")	-	-	-
4.4 , Table No . 2 , iii)(Minimum cross section of the stud)	-	-	-
4.4 , Table No . 2 , iv)(Stud bolt)	-	-	-
4.4 , Table No . 3 , i)(Toe post attachment strength)	-	-	-
4.4 , Table No . 3 , ii)(Attachment strength of rear strap)	-	-	-
4.4 , Table No . 3 , iii)(Inter layer bond strength)	-	-	-
6(MARKING AND PACKING)	-	-	-
Cl. No.5.1,Table no.1 of IS 17011(iv)(Chromium (VI))	-	-	-
Cl. No.5.1,Table no.1 of IS 17011(x)(pH)	-	-	-
Clause 4.1 - 4.1.1(Bottom Material)	-	-	-
Clause 4.1 - 4.1.2(Strap Material)	-	-	-
Clause 4.1 - 4.1.4(Material)	-	-	-
Clause 4.2(Material)	-	-	-
Clause 4.3 - 4.3.1(Thickness)	-	-	-
Clause 4.3 - 4.3.2(Thickness)	-	-	-
Clause 4.4 Table 1 -i)(Density, g/cm3, Min)	-	-	-
Clause 4.4 Table 2 -i) - b(Density, g/cm3 Cellular strap)	-	-	-
Clause 4.4 Table 1 -iii)(Split tear strength, kg, Min)	-	-	-
Clause 4.4 Table 1 -iv) - a("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, percent, Max")	-	-	-
Clause 4.4 Table 1 -iv) - b(Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber, percent, Max)	-	-	-
Clause 4.4 Table 1 -v)(Abrasion resistance at applied force 5 N)	-	-	-
Clause 4.4 Table 2 -i) - a("Density, g/cm3 Solid strap ")	-	-	-
Clause 4.4 Table 2 -ii) - a - 1("Breaking strength, kgf, Min Strap to strap(Solid Strap)")	-	-	-
Clause 4.4 Table 2 -ii) - a - 2("Breaking strength, kgf, Min Strap to strap(Cellular Strap)")	-	-	-
Clause 4.4 Table 2 -ii) - a - 3("Breaking strength, kgf, Min Toe portion to strap(Solid Strap)")	-	-	-
Clause 4.4 Table 2 -ii) - a - 4("Breaking strength, kgf, Min Toe portion to strap(Cellular Strap)")	-	-	-
Clause 4.4 Table 2 -ii) - b - 1("Elongation at break, percent (Applicable to strap to strap (V shape) Solid Strap")	-	-	-
Clause 4.4 Table 2 -ii) - b - 2("Elongation at break, percent (Applicable to strap to strap (V shape) Cellular Strap")	-	-	-
Clause 4.4 Table 2 -iii) - a("Minimum cross section of the stud, mm, Size 1 to 13 (Adult)")	-	-	-
Clause 4.4 Table 2 -iii) - b("Minimum cross section of the stud, mm, Size 3 to 13 (Children)")	-	-	-
Clause 4.4 Table 2 -iv) - a("Stud bolt, mm Diameter/edge to edge length")	-	-	-
Clause 4.4 Table 2 -iv) - b("Stud bolt, mm Thickness")	-	-	-
Clause 4.4 Table 3 -i)("Toe post attachment strength, N, Min")	-	-	-
Clause 4.4 Table 3 -iii)("Inter layer bond strength, N/mm, Min")	-	-	-
Clause 4.1 - 4.1.3(Material)	-	-	-
Clause 4.4 Table 3 -ii)("Attachment strength of rear strap, N, Min")	-	-	-
Cl-4 ((Amendment No-1)(Category And Type)	-	-	-
Cl-4.4, Table -1 S. No-1 (i) (Amendment No-1)(Compression set at constant stress)	-	-	-
Cl-4.4, Table -1 S. No-1 (ii) (Amendment No-1)(Split tear strength)	-	-	-
Cl-4.4, Table -1 S. No-1 (iii) (a)(Amendment No-1)("Shrinkage at Shrinkage at 50 °C ± 1 °C for 2 h for polymeric material, percent, Max ")	-	-	-
Cl-4.4, Table -1 S. No-1 (iii)(b) (Amendment No-1)(Shrinkage at 100 °C ± 1 °C for 1 h for rubber, percent, Max)	-	-	-
Cl-4.4, Table -1 S. No-1 (iv) (Amendment No-1)(Abrasion resistance at applied force)	-	-	-
Cl-4.4, Table -1 S. No-1 (v) (Amendment No-1)(Flexing resistance: Maximum cut growth,)	-	-	-
Cl-4.4, Table -1 S. No-1 (vi) (Amendment No-1)(Hydrolysis resistance:Maximum cut growth)	-	-	-
Cl-4.4, Table -2 S. No-1 (i), a (Amendment No-1)("Breaking strength for Strap to strap 1-Solid strap 2-Cellular strap")	-	-	-
Cl-4.4, Table -2 S. No-1 (i), b (Amendment No-1)("Breaking strength for Toe portion to strap 1-Solid strap 2-Cellular strap")	-	-	-
Cl-4.4, Table -2 S. No-1 (i), c (Amendment No-1)("Elongation at break , percent, Min 1-Solid strap 2-Cellular strap")	-	-	-
Cl-4.4, Table -3 S. No-1 (i), (Amendment No-1)(Toe post attachment strength)	-	-	-
Cl-4.4, Table -3 S. No-1 (ii), (Amendment No-1)(Attachment strength of rear strap)	-	-	-
Cl-4.4, Table -3 S. No-1 (iii), (Amendment No-1)(Inter layer bond strength)	-	-	-

02 Sep, 2027

-
Exclusion: Table 1 vii and Table 2 ii Chemical requirements, Table 1 viii and Table 2 iii Lead content

6963

Bahadurgarh Footwear Development Services (BFDS), Bahadurgarh

8168806

IS 15844 : Part 1 (2023)

SPORTS FOOTWEAR PART -1 GENERAL PURPOSEFirst Revision

22000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl No.4.1(Sampling and Conditioning)	-	500	-
Cl No.4.2(Construction)	-	300	-
Cl No.4.3(Whole Footwear)	-	300	-
4.3.1(Insole)	-	300	-
4.3.2(Toe spring height)	-	500	-
4.3.3(Upper to Mid Sole/Out Sole Bond Performance)	-	500	-
4.3.4("Upper to Composite Sole Bond Performance (Applicable Only When the Sole is Composite)")	-	500	-
4.3.5(Out Sole to Mid Sole (Multilayer) Bond Performance)	-	500	-
4.3.6(Energy Absorption at Seat Region)	-	800	-
4.3.7(Complete Shoe Flexing)	-	640	-
4.3.8(Washability)	-	800	-
4.3.9(Slip Resistance)	-	1000	-
Cl No.4.4 , Table No. 2 , i) , a)(Flexing resistance, Dry condition)	-	600	-
Cl No.4.4 , Table No. 2 , ii)(Tear strength (average force), Min, N)	-	450	-
Cl No.4.4 , Table No. 2 , iii) , a)("Colour fastness rubbing (To and fro) Grey scale rate, Min , Dry: (rubbing) Rating: (Marring and staining) ")	-	600	-
Cl No.4.4 , Table No. 2 , iii) , b)("Colour fastness rubbing (To and fro) Grey scale rate, Min , Wet: (rubbing) Rating: (Marring and staining)")	-	600	-
Cl No.4.4 , Table No. 2 , iv) , a)(Water vapour permeability, mg/cm2h, Min)	-	800	-
Cl No.4.4 , Table No. 2 , iv) , b)(Water vapour coefficient, mg/cm2 , Min)	-	800	-
Cl No.4.4 , Table No. 2 , v)(Stitch tear strength (double hole), N/mm, Min)	-	600	-
Cl No.4.4 , Table No. 2 , i)(Breaking strength, N/mm, Min)	-	450	-
Cl No.4.4 , Table No. 2 , ii)(Elongation at break, percent Min)	-	450	-
Cl No.4.4 , Table No. 2 , iii)(Tear strength, N, Min For Fabric: For all other materials)	-	450	-
Cl No.4.4 , Table No. 2 , iv) , a)(Flexing resistance, Dry condition)	-	600	-
Cl No.4.4 , Table No. 2 , iv) , b)(Flexing resistance, ,Wet condition)	-	600	-
Cl No.4.4 , Table No. 2 , v) , a)(Water vapour permeability, mg/cm2h, Min)	-	800	-
Cl No.4.4 , Table No. 2 , v) , b)("Water vapour coefficient, mg/cm2 , Min ")	-	800	-
Cl No.4.4 , Table No. 2 , vi)(Hydrolysis resistance)	-	2000	-
Cl No.4.4 , Table No. 2 , vii)(Bursting Strength, kg/cm2 , Min)	-	500	-
Cl No.4.5 , Table No. 3 , i)(Tear strength, N, Min)	-	450	-
Cl No.4.5 , Table No. 3 , ii)(Abrasion resistance, cycles)	-	600	-
Cl No.4.5 , Table No. 3 , iii)("Colour fastness to rubbing (crocking), Grey scale rate with 10 rubs on dry or wet, Min")	-	600	-
Cl No.4.5 , Table No. 3 , iv)("Colour fastness to perspiration (contact method) Grey scale rate, Min")	-	600	-
Cl No.4.5 , Table No. 3 , v) , a)(Water vapour permeability, mg/cm2h, Min)	-	800	-
Cl No.4.5 , Table No. 3 , v) , b)("Water vapour coefficient, mg/cm2 , Min ")	-	800	-
Cl No.4.6 , Table No. 4 , i)(Thickness, mm, Min)	-	200	-
Cl No.4.6 , Table No. 4 , ii)(Flexing index, Min)	-	800	-
Cl No.4.6 , Table No. 4 , iii)(Abrasion resistance, at 400 cycles)	-	800	-
Cl No.4.6 , Table No. 4 , iv) , a)(Water Absorption, mg/cm2 , Min)	-	800	-
Cl No.4.6 , Table No. 4 , iv) , b)(Water Desorption, percent, Min)	-	800	-
Cl No.4.7, Table No. 5 , i)(Thickness, mm, Min)	-	200	-
Cl No.4.7, Table No. 5 , ii)(Abrasion resistance, cycles)	-	600	-
Cl No.4.7, Table No. 5 , iii) , a)(Water Absorption, mg/cm2 , Min)	-	800	-
Cl No.4.7, Table No. 5 , iii) , b)(Water Desorption, percent, Min)	-	800	-
Cl No.4.8 , Table No. 6 , i)(Abrasion resistance (Volume loss), mm3 , Max)	-	600	-
Cl No.4.8 , Table No. 6 , ii)("Flexing resistance Belt Method at 90 diameter Mandrel or Bennewart method, cut growth, Max")	-	600	-
Cl No.4.8 , Table No. 6 , iii)("Hydrolysis resistance, cut growth after 150 000 flexes, in mm, Max")	-	2000	-
Cl No.4.9 , Table No. 7 , i)(Compression set, percent, Max)	-	500	-
Cl No.4.9 , Table No. 7 , ii)(Split tear strength, kg/25 mm, Min)	-	450	-
Cl No.4.9 , Table No. 7 , iii)(Heat shrinkage, percent, Max)	-	800	-
Cl No.4.10 , Table No. 8 , i)(First dry collapsing load, hardness, N, Min)	-	800	-
Cl No.4.10 , Table No. 8 , ii)(Resilience, percent, Min)	-	800	-
Cl No.4.10 , Table No. 8 , iii)(Moisture resistance, percent, Min)	-	800	-
Cl No.4.10 , Table No. 8 , iv) , a)(Initial dry area shape retention, percent, Min)	-	800	-
Cl No.4.10 , Table No. 8 , iv) , b)(Area shape retention after 10th collapse, dry, percent, Min)	-	800	-
Cl No.4.11 , Table No. 9 , i)(Peel strength, N/mm, Min)	-	500	-
Cl No.4.11 , Table No. 9 , ii)(Shear strength, kPa , Min)	-	600	-
Cl No.4.12 , Table No. 10 , i)(Limit of useful extension, percent, Min)	-	600	-
Cl No.4.13 , Table No. 11 , i)(Breaking strength of lace, N, Min)	-	500	-
Cl No.4.13 , Table No. 11 , ii)(Lace tag strength, N, Min)	-	500	-
Cl No.4.13 , Table No. 11 , iii)(Lace to lace abrasion,)	-	800	-
Cl No.4.13 , Table No. 11 , iv)("Colour fastness to water Gray Scale Rate, Min Rating")	-	600	-
Cl No.4.13 , Table No. 11 , v)(Strength of Buckle/Ski hook, N, Min)	-	600	-
Cl No.4.13 , Table No. 11 , vi)(Corrosion resistance)	-	600	-
Cl No . 5(MARKING AND PACKING)	-	1000	-
Cl No . 4.14, Table no. 1 of IS 17011(iv)(Chromium (VI))	-	600	-
Cl No . 4.14, Table no. 1 of IS 17011(x)(pH)	-	400	-
Clause 4.2 - 4.2.1(Construction)	-	200	-
Clause 4.2 - 4.2.2(Construction)	-	200	-
Clause 4.3 - 4.3.1(Whole Footwear)	-	200	-
Clause 4.3 - 4.3.2(Whole Footwear)	-	200	-
Clause 4.3 - 4.3.3(Upper to Mid Sole/Out Sole Bond Performance)	-	500	-
Clause 4.3 - 4.3.4(Upper to Composite Sole Bond Performance(Applicable Only When the Sole is Composite))	-	500	-
Clause 4.3 - 4.3.5(Out Sole to Mid Sole (Multilayer) Bond)	-	500	-
Clause 4.3 - 4.3.7(Complete Shoe Flexing)	-	640	-
Clause 4.4, Table 1 ii)(Tear strength)	-	450	-
Clause 4.4, Table 1 iv)-a(Water Vapour Permeability)	-	800	-
Clause 4.5, Table 3 v)-b(Water Vapour Coeffecient)	-	800	-
Clause 4.4, Table 1 v)(Stitch Tear Strength(Double Hole))	-	600	-
Clause 4.4, Table 2 i)(Breaking Strength)	-	450	-
Clause 4.4, Table 2 ii)(Elongation at break)	-	450	-
Clause 4.4, Table 2 iii)(Tear strength)	-	450	-
Clause 4.4, Table 2 v)-a(Water Vapour Permeability)	-	800	-
Clause 4.4, Table 2 v)-b(Water Vapour Coeffecient)	-	800	-
Clause 4.5, Table 3 i)(Tear strength)	-	450	-
Clause 4.5, Table 3 ii)(Abrasion Resistance)	-	600	-
Clause 4.5, Table 3 v)-a(Water Vapour Permeability)	-	800	-
Clause 4.6, Table 4 i)(Thickness)	-	200	-
Clause 4.6, Table 4 ii)(Abrasion Resistance)	-	600	-
Clause 4.6, Table 4 iv)-a(Water Absorption)	-	800	-
Clause 4.6, Table 4 iv)-b(Water Desorption)	-	800	-
Clause 4.8, Table 6 i)(Abrasion Resistance)	-	600	-
Clause 4.8, Table 6 ii)(Flexing Resistance)	-	600	-
Clause 4.8, Table 6 iii)(Hydrolysis Resistance)	-	2000	-
Clause 4.9, Table 7 ii)(Split Tear strength)	-	450	-
Clause 4.9, Table 7 iii)(Heat shrinkage)	-	800	-
Clause 4.4, Table 1 iv)-b(Water Vapour Coeffecient)	-	800	-
Clause 4.7, Table 5 i)(Thickness)	-	200	-
Clause 4.7, Table 5 iii)-a(Water Absorption)	-	800	-
Cl No.4.4 , Table No. 2 , i) , b)(Flexing resistance, Wet condition)	-	600	-
Clause 4.7, Table 5 ii)(Abrasion Resistance)	-	600	-
Clause 4.7, Table 5 iii)-b(Water Desorption)	-	800	-
Cl No.4.1(Sampling and Conditioning)	-	200	-
Cl No.4.2(Construction)	-	200	-
Cl No.4.3(Whole Footwear)	-	200	-
4.3.1(Insole)	-	200	-
4.3.2(Toe spring height)	-	200	-
4.3.3(Upper to Mid Sole/Out Sole Bond Performance)	-	500	-
4.3.4("Upper to Composite Sole Bond Performance (Applicable Only When the Sole is Composite)")	-	500	-
4.3.5(Out Sole to Mid Sole (Multilayer) Bond Performance)	-	500	-
4.3.6(Energy Absorption at Seat Region)	-	800	-
4.3.7(Complete Shoe Flexing)	-	640	-
4.3.9(Slip Resistance)	-	1500	-
Cl No.4.4 , Table No. 2 , i) , a)(Flexing resistance, Dry condition)	-	600	-
Cl No.4.4 , Table No. 2 , ii)(Tear strength (average force), Min, N)	-	450	-
Cl No.4.4 , Table No. 2 , iii) , a)("Colour fastness rubbing (To and fro) Grey scale rate, Min , Dry: (rubbing) Rating: (Marring and staining) ")	-	500	-
Cl No.4.4 , Table No. 2 , iii) , b)("Colour fastness rubbing (To and fro) Grey scale rate, Min , Wet: (rubbing) Rating: (Marring and staining)")	-	500	-
Cl No.4.4 , Table No. 2 , iv) , a)(Water vapour permeability, mg/cm2h, Min)	-	800	-
Cl No.4.4 , Table No. 2 , iv) , b)(Water vapour coefficient, mg/cm2 , Min)	-	800	-
Cl No.4.4 , Table No. 2 , v)(Stitch tear strength (double hole), N/mm, Min)	-	450	-
Cl No.4.4 , Table No. 2 , i)(Breaking strength, N/mm, Min)	-	450	-
Cl No.4.4 , Table No. 2 , ii)(Elongation at break, percent Min)	-	450	-
Cl No.4.4 , Table No. 2 , iii)(Tear strength, N, Min For Fabric: For all other materials)	-	450	-
Cl No.4.4 , Table No. 2 , iv) , a)(Flexing resistance, Dry condition)	-	600	-
Cl No.4.4 , Table No. 2 , iv) , b)(Flexing resistance, ,Wet condition)	-	600	-
Cl No.4.4 , Table No. 2 , v) , a)(Water vapour permeability, mg/cm2h, Min)	-	800	-
Cl No.4.4 , Table No. 2 , v) , b)("Water vapour coefficient, mg/cm2 , Min ")	-	800	-
Cl No.4.4 , Table No. 2 , vi)(Hydrolysis resistance)	-	2500	-
Cl No.4.4 , Table No. 2 , vii)(Bursting Strength, kg/cm2 , Min)	-	600	-
Cl No.4.5 , Table No. 3 , i)(Tear strength, N, Min)	-	450	-
Cl No.4.5 , Table No. 3 , ii)(Abrasion resistance, cycles)	-	600	-
Cl No.4.5 , Table No. 3 , iii)("Colour fastness to rubbing (crocking), Grey scale rate with 10 rubs on dry or wet, Min")	-	500	-
Cl No.4.5 , Table No. 3 , iv)("Colour fastness to perspiration (contact method) Grey scale rate, Min")	-	500	-
Cl No.4.5 , Table No. 3 , v) , a)(Water vapour permeability, mg/cm2h, Min)	-	800	-
Cl No.4.5 , Table No. 3 , v) , b)("Water vapour coefficient, mg/cm2 , Min ")	-	800	-
Cl No.4.6 , Table No. 4 , i)(Thickness, mm, Min)	-	200	-
Cl No.4.6 , Table No. 4 , ii)(Flexing index, Min)	-	600	-
Cl No.4.6 , Table No. 4 , iii)(Abrasion resistance, at 400 cycles)	-	600	-
Cl No.4.6 , Table No. 4 , iv) , a)(Water Absorption, mg/cm2 , Min)	-	800	-
Cl No.4.6 , Table No. 4 , iv) , b)(Water Desorption, percent, Min)	-	800	-
Cl No.4.7, Table No. 5 , i)(Thickness, mm, Min)	-	200	-
Cl No.4.7, Table No. 5 , ii)(Abrasion resistance, cycles)	-	800	-
Cl No.4.7, Table No. 5 , iii) , a)(Water Absorption, mg/cm2 , Min)	-	800	-
Cl No.4.7, Table No. 5 , iii) , b)(Water Desorption, percent, Min)	-	800	-
Cl No.4.8 , Table No. 6 , i)(Abrasion resistance (Volume loss), mm3 , Max)	-	600	-
Cl No.4.8 , Table No. 6 , ii)("Flexing resistance Belt Method at 90 diameter Mandrel or Bennewart method, cut growth, Max")	-	600	-
Cl No.4.8 , Table No. 6 , iii)("Hydrolysis resistance, cut growth after 150 000 flexes, in mm, Max")	-	2500	-
Cl No.4.9 , Table No. 7 , i)(Compression set, percent, Max)	-	500	-
Cl No.4.9 , Table No. 7 , ii)(Split tear strength, kg/25 mm, Min)	-	450	-
Cl No.4.9 , Table No. 7 , iii)(Heat shrinkage, percent, Max)	-	800	-
Cl No.4.10 , Table No. 8 , i)(First dry collapsing load, hardness, N, Min)	-	800	-
Cl No.4.10 , Table No. 8 , ii)(Resilience, percent, Min)	-	800	-
Cl No.4.10 , Table No. 8 , iii)(Moisture resistance, percent, Min)	-	800	-
Cl No.4.10 , Table No. 8 , iv) , a)(Initial dry area shape retention, percent, Min)	-	800	-
Cl No.4.10 , Table No. 8 , iv) , b)(Area shape retention after 10th collapse, dry, percent, Min)	-	800	-
Cl No.4.11 , Table No. 9 , i)(Peel strength, N/mm, Min)	-	500	-
Cl No.4.11 , Table No. 9 , ii)(Shear strength, kPa , Min)	-	600	-
Cl No.4.12 , Table No. 10 , i)(Limit of useful extension, percent, Min)	-	800	-
Cl No.4.13 , Table No. 11 , i)(Breaking strength of lace, N, Min)	-	500	-
Cl No.4.13 , Table No. 11 , ii)(Lace tag strength, N, Min)	-	500	-
Cl No.4.13 , Table No. 11 , iii)(Lace to lace abrasion,)	-	800	-
Cl No.4.13 , Table No. 11 , iv)("Colour fastness to water Gray Scale Rate, Min Rating")	-	600	-
Cl No.4.13 , Table No. 11 , v)(Strength of Buckle/Ski hook, N, Min)	-	500	-
Cl No.4.13 , Table No. 11 , vi)(Corrosion resistance)	-	600	-
Cl No . 5(MARKING AND PACKING)	-	500	-
Cl No . 4.14, Table no. 1 of IS 17011(iv)(Chromium (VI))	-	800	-
Cl No . 4.14, Table no. 1 of IS 17011(x)(pH)	-	500	-
Clause 4.2 - 4.2.1(Construction)	-	200	-
Clause 4.2 - 4.2.2(Construction)	-	200	-
Clause 4.3 - 4.3.1(Whole Footwear)	-	500	-
Clause 4.3 - 4.3.2(Whole Footwear)	-	500	-
Clause 4.3 - 4.3.3(Upper to Mid Sole/Out Sole Bond Performance)	-	500	-
Clause 4.3 - 4.3.4(Upper to Composite Sole Bond Performance(Applicable Only When the Sole is Composite))	-	500	-
Clause 4.3 - 4.3.5(Out Sole to Mid Sole (Multilayer) Bond)	-	500	-
Clause 4.3 - 4.3.7(Complete Shoe Flexing)	-	640	-
Clause 4.4, Table 1 ii)(Tear strength)	-	450	-
Clause 4.4, Table 1 iv)-a(Water Vapour Permeability)	-	800	-
Clause 4.5, Table 3 v)-b(Water Vapour Coeffecient)	-	800	-
Clause 4.4, Table 1 v)(Stitch Tear Strength(Double Hole))	-	450	-
Clause 4.4, Table 2 i)(Breaking Strength)	-	450	-
Clause 4.4, Table 2 ii)(Elongation at break)	-	450	-
Clause 4.4, Table 2 iii)(Tear strength)	-	450	-
Clause 4.4, Table 2 v)-a(Water Vapour Permeability)	-	800	-
Clause 4.4, Table 2 v)-b(Water Vapour Coeffecient)	-	800	-
Clause 4.5, Table 3 i)(Tear strength)	-	450	-
Clause 4.5, Table 3 ii)(Abrasion Resistance)	-	600	-
Clause 4.5, Table 3 v)-a(Water Vapour Permeability)	-	800	-
Clause 4.6, Table 4 i)(Thickness)	-	200	-
Clause 4.6, Table 4 ii)(Abrasion Resistance)	-	600	-
Clause 4.6, Table 4 iv)-a(Water Absorption)	-	800	-
Clause 4.6, Table 4 iv)-b(Water Desorption)	-	800	-
Clause 4.8, Table 6 i)(Abrasion Resistance)	-	600	-
Clause 4.8, Table 6 ii)(Flexing Resistance)	-	600	-
Clause 4.8, Table 6 iii)(Hydrolysis Resistance)	-	2500	-
Clause 4.9, Table 7 ii)(Split Tear strength)	-	450	-
Clause 4.9, Table 7 iii)(Heat shrinkage)	-	800	-
Clause 4.4, Table 1 iv)-b(Water Vapour Coeffecient)	-	800	-
Clause 4.7, Table 5 i)(Thickness)	-	200	-
Clause 4.7, Table 5 iii)-a(Water Absorption)	-	800	-
Cl No.4.4 , Table No. 2 , i) , b)(Flexing resistance, Wet condition)	-	600	-
Clause 4.7, Table 5 ii)(Abrasion Resistance)	-	800	-
Clause 4.7, Table 5 iii)-b(Water Desorption)	-	800	-
Cl-5, Table -1 S. No-(i) (Amendment No-1)(Insole)	-	200	-
Cl-5, Table -1 S. No- (ii) (Amendment No-1)(Toe spring height)	-	200	-
Cl-5, Table -1 S. No- (iii) (Amendment No-1)("Bond performance (a) Upper to sole/mid sole/composite sole (b) Interlayer bond strength")	-	500	-
Cl-5, Table -1 S. No- (iv) (Amendment No-1)(Energy absorption at seat region)	-	800	-
Cl-5, Table -1 S. No- (v) (Amendment No-1)(Complete shoe flexing)	-	640	-
Cl-5, Table -1 S. No-(vi) (Amendment No-1)(Washability)	-	800	-
Cl-5, Table -1 S. No- (vii) (Amendment No-1)(Slip resistance, coefficient of friction (COF),)	-	1500	-
Cl-5, Table -1 S. No- (viii) (Amendment No-1)("Abrasion resistance a-Cellular sole b-Solid sole")	-	600	-
Cl-5, Table -1 S. No- (xi) (Amendment No-1)(Hydrolysis resistance)	-	2500	-
Cl-6, Table -2 S. No- (i) (Amendment No-1)(Tear strength)	-	450	-
Cl-6, Table -2 S. No- (ii) (Amendment No-1)("Colour fastness rubbing a-Dry: (rubbing) b-Wet: (rubbing)")	-	500	-
Cl-6, Table -2 S. No- (iii), a) (Amendment No-1)(Water vapour permeability)	-	800	-
Cl-6, Table -2 S. No- (iii), b) (Amendment No-1)(Water vapour coefficient)	-	800	-
Cl-6, Table -2 S. No- (iv),(Amendment No-1)(Stitch tear strength)	-	450	-
Cl-6, Table -3 S. No- (i),(Amendment No-1)(Breaking strength, N/mm, Min)	-	500	-
Cl-6, Table -3 S. No- (ii),(Amendment No-1)("Elongation at break a-Tighter direction b-Stretch direction")	-	450	-
Cl-6, Table -3 S. No- (iii),(Amendment No-1)("Tear strength, N, Min a) For fabric b) For all other materials")	-	450	-
Cl-6, Table -3 S. No- (iv),(Amendment No-1)("Flexing resistance a- Dry condition b-Wet condition")	-	600	-
Cl-6, Table -3 S. No- (v), a (Amendment No-1)(Water vapour permeability)	-	800	-
Cl-6, Table -3 S. No- (v), b (Amendment No-1)(Water vapour coefficient)	-	800	-
Cl-6, Table -3 S. No- (vi), (Amendment No-1)(Hydrolysis resistance)	-	2500	-
Cl-6, Table -3 S. No- (vii), (Amendment No-1)(Bursting strength)	-	800	-
Cl-6, Table -4 S. No- (ii),(Amendment No-1)("Abrasion resistance, cycles a- Dry condition b-Wet condition")	-	600	-
Cl-6, Table -4 S. No- (iii),(Amendment No-1)(Colour fastness to rubbing , grey scale rate with 10 rubs on dry or wet, Min)	-	500	-
Cl-6, Table -4 S. No- (iv),(Amendment No-1)(Colour fastness to perspiration)	-	800	-
Cl-6, Table -4 S. No- (v), a (Amendment No-1)(Water vapour permeability)	-	800	-
Cl-6, Table -4 S. No- (v), b (Amendment No-1)(Water vapour coefficient)	-	800	-
Cl-6, Table -5 S. No- (i), (Amendment No-1)(Thickness, mm, Min)	-	200	-
Cl-6, Table -5 S. No-(ii), (Amendment No-1)(Flexing index, Min)	-	640	-
Cl-6, Table -5 S. No-(iii), (Amendment No-1)(Abrasion resistance,)	-	600	-
Cl-6, Table -5 S. No- (iv), a (Amendment No-1)(Water absorption)	-	800	-
Cl-6, Table -5 S. No- (iv), b (Amendment No-1)(Water desorption, percent)	-	800	-
Cl-6, Table -6 S. No- (i), (Amendment No-1)(Thickness, mm, Min)	-	200	-
Cl-6, Table -6 S. No- (ii), (Amendment No-1)("Abrasion resistance, cycles a- Dry condition b-Wet condition")	-	600	-
Cl-6, Table -6 S. No- (iii),a (Amendment No-1)(Water absorption)	-	800	-
Cl-6, Table -6 S. No- (iv), b (Amendment No-1)(Water desorption, percent)	-	800	-
Cl-6, Table -7 S. No- (i), (Amendment No-1)(Flexing resistance (Belt method or Bennewart method))	-	600	-
Cl-6, Table -7 S. No- (ii), (Amendment No-1)(Hydrolysis resistance, cut growth after flexes)	-	2500	-
Cl-6, Table -8 S. No- (i), (Amendment No-1)("Compression set, percent, Max a) For EVA b) For all other materials")	-	500	-
Cl-6, Table -8 S. No- (ii), (Amendment No-1)(Split tear strength)	-	450	-
Cl-6, Table -8 S. No- (iii), (Amendment No-1)(Heat shrinkage)	-	800	-
Cl-6, Table -9 S. No- (i), (Amendment No-1)(First dry collapsing load, hardness)	-	800	-
Cl-6, Table -9 S. No- (ii), (Amendment No-1)(Resilience, percent)	-	800	-
Cl-6, Table -9 S. No- (iii), (Amendment No-1)(Moisture resistance)	-	800	-
Cl-6, Table -9 S. No- (iv), a (Amendment No-1)(Initial dry area shape retention)	-	800	-
Cl-6, Table -9 S. No- (iv), b (Amendment No-1)(Area shape retention after 10th collapse)	-	800	-
Cl-6, Table -10 S. No- (i), (Amendment No-1)("Peel strength a) Initial b) After 5 000 wear cycles")	-	500	-
Cl-6, Table -10 S. No- (ii), (Amendment No-1)("Shear strength a) Initial b) After 5 000 wear cycles")	-	500	-
Cl-6, Table -11 S. No- (i), (Amendment No-1)(Limit of useful extension)	-	800	-
Cl-6, Table -12 S. No- (i), (Amendment No-1)(Breaking strength of lace)	-	500	-
Cl-6, Table -12 S. No- (ii), (Amendment No-1)(Lace tag strength)	-	500	-
Cl-6, Table -12 S. No- (iii), (Amendment No-1)(Lace to lace abrasion)	-	800	-
Cl-6, Table -12 S. No- (iv), (Amendment No-1)(Colour fastness to water (for lace) (contact method))	-	500	-
Cl-6, Table -12 S. No- (iv), (Amendment No-1)(Colour fastness to water (for lace) (contact method))	-	500	-
Cl-6, Table -12 S. No (v), (Amendment No-1)(Strength of buckle/ski hook)	-	500	-
Cl-6, Table -12 S. No- (vi), (Amendment No-1)(Corrosion resistance)	-	600	-
Cl-6, Table -4 S. No- (i),(Amendment No-1)(Tear strength, N, Min)	-	450	-
Cl No.4.1(Sampling and Conditioning)	-	500	-
Cl No.4.2(Construction)	-	300	-
Cl No.4.3(Whole Footwear)	-	300	-
4.3.1(Insole)	-	300	-
4.3.2(Toe spring height)	-	500	-
Cl No.4.4 , Table No. 2 , i)(Breaking strength, N/mm, Min)	-	500	-
Cl No.4.4 , Table No. 2 , vii)(Bursting Strength, kg/cm2 , Min)	-	500	-
Cl No.4.7, Table No. 5 , ii)(Abrasion resistance, cycles)	-	600	-
Cl No.4.10 , Table No. 8 , ii)(Resilience, percent, Min)	-	500	-
Cl No.4.11 , Table No. 9 , ii)(Shear strength, kPa , Min)	-	800	-
Cl No.4.13 , Table No. 11 , iv)("Colour fastness to water Gray Scale Rate, Min Rating")	-	500	-
Cl No . 5(MARKING AND PACKING)	-	600	-
Clause 4.2 - 4.2.1(Construction)	-	500	-
Clause 4.2 - 4.2.2(Construction)	-	500	-
Clause 4.3 - 4.3.1(Whole Footwear)	-	600	-
Clause 4.3 - 4.3.2(Whole Footwear)	-	600	-
Clause 4.4, Table 2 i)(Breaking Strength)	-	500	-
Clause 4.9, Table 7 iii)(Heat shrinkage)	-	2000	-
Clause 4.7, Table 5 ii)(Abrasion Resistance)	-	600	-
Cl-5, Table -1 S. No-(i) (Amendment No-1)(Insole)	-	500	-
Cl-5, Table -1 S. No- (ii) (Amendment No-1)(Toe spring height)	-	500	-
Cl-5, Table -1 S. No- (iii) (Amendment No-1)("Bond performance (a) Upper to sole/mid sole/composite sole (b) Interlayer bond strength")	-	500	-
Cl-5, Table -1 S. No- (iv) (Amendment No-1)(Energy absorption at seat region)	-	800	-
Cl-5, Table -1 S. No- (v) (Amendment No-1)(Complete shoe flexing)	-	600	-
Cl-5, Table -1 S. No- (vii) (Amendment No-1)(Slip resistance, coefficient of friction (COF),)	-	1500	-
Cl-5, Table -1 S. No- (viii) (Amendment No-1)("Abrasion resistance a-Cellular sole b-Solid sole")	-	600	-
Cl-5, Table -1 S. No- (xi) (Amendment No-1)(Hydrolysis resistance)	-	2500	-
Cl-6, Table -2 S. No- (i) (Amendment No-1)(Tear strength)	-	450	-
Cl-6, Table -2 S. No- (ii) (Amendment No-1)("Colour fastness rubbing a-Dry: (rubbing) b-Wet: (rubbing)")	-	500	-
Cl-6, Table -2 S. No- (iii), a) (Amendment No-1)(Water vapour permeability)	-	800	-
Cl-6, Table -2 S. No- (iii), b) (Amendment No-1)(Water vapour coefficient)	-	800	-
Cl-6, Table -2 S. No- (iv),(Amendment No-1)(Stitch tear strength)	-	450	-
Cl-6, Table -3 S. No- (i),(Amendment No-1)(Breaking strength, N/mm, Min)	-	500	-
Cl-6, Table -3 S. No- (ii),(Amendment No-1)("Elongation at break a-Tighter direction b-Stretch direction")	-	450	-
Cl-6, Table -3 S. No- (iii),(Amendment No-1)("Tear strength, N, Min a) For fabric b) For all other materials")	-	450	-
Cl-6, Table -3 S. No- (iv),(Amendment No-1)("Flexing resistance a- Dry condition b-Wet condition")	-	600	-
Cl-6, Table -3 S. No- (v), a (Amendment No-1)(Water vapour permeability)	-	800	-
Cl-6, Table -3 S. No- (v), b (Amendment No-1)(Water vapour coefficient)	-	800	-
Cl-6, Table -3 S. No- (vi), (Amendment No-1)(Hydrolysis resistance)	-	2500	-
Cl-6, Table -3 S. No- (vii), (Amendment No-1)(Bursting strength)	-	600	-
Cl-6, Table -4 S. No- (ii),(Amendment No-1)("Abrasion resistance, cycles a- Dry condition b-Wet condition")	-	600	-
Cl-6, Table -4 S. No- (iii),(Amendment No-1)(Colour fastness to rubbing , grey scale rate with 10 rubs on dry or wet, Min)	-	500	-
Cl-6, Table -4 S. No- (iv),(Amendment No-1)(Colour fastness to perspiration)	-	600	-
Cl-6, Table -4 S. No- (v), a (Amendment No-1)(Water vapour permeability)	-	800	-
Cl-6, Table -4 S. No- (v), b (Amendment No-1)(Water vapour coefficient)	-	800	-
Cl-6, Table -5 S. No- (i), (Amendment No-1)(Thickness, mm, Min)	-	200	-
Cl-6, Table -5 S. No-(ii), (Amendment No-1)(Flexing index, Min)	-	600	-
Cl-6, Table -5 S. No-(iii), (Amendment No-1)(Abrasion resistance,)	-	600	-
Cl-6, Table -5 S. No- (iv), a (Amendment No-1)(Water absorption)	-	800	-
Cl-6, Table -5 S. No- (iv), b (Amendment No-1)(Water desorption, percent)	-	800	-
Cl-6, Table -6 S. No- (i), (Amendment No-1)(Thickness, mm, Min)	-	200	-
Cl-6, Table -6 S. No- (ii), (Amendment No-1)("Abrasion resistance, cycles a- Dry condition b-Wet condition")	-	600	-
Cl-6, Table -6 S. No- (iii),a (Amendment No-1)(Water absorption)	-	800	-
Cl-6, Table -6 S. No- (iv), b (Amendment No-1)(Water desorption, percent)	-	800	-
Cl-6, Table -7 S. No- (i), (Amendment No-1)(Flexing resistance (Belt method or Bennewart method))	-	600	-
Cl-6, Table -7 S. No- (ii), (Amendment No-1)(Hydrolysis resistance, cut growth after flexes)	-	2500	-
Cl-6, Table -8 S. No- (i), (Amendment No-1)("Compression set, percent, Max a) For EVA b) For all other materials")	-	500	-
Cl-6, Table -8 S. No- (ii), (Amendment No-1)(Split tear strength)	-	450	-
Cl-6, Table -8 S. No- (iii), (Amendment No-1)(Heat shrinkage)	-	800	-
Cl-6, Table -9 S. No- (i), (Amendment No-1)(First dry collapsing load, hardness)	-	800	-
Cl-6, Table -9 S. No- (ii), (Amendment No-1)(Resilience, percent)	-	800	-
Cl-6, Table -9 S. No- (iii), (Amendment No-1)(Moisture resistance)	-	800	-
Cl-6, Table -9 S. No- (iv), a (Amendment No-1)(Initial dry area shape retention)	-	800	-
Cl-6, Table -9 S. No- (iv), b (Amendment No-1)(Area shape retention after 10th collapse)	-	800	-
Cl-6, Table -10 S. No- (i), (Amendment No-1)("Peel strength a) Initial b) After 5 000 wear cycles")	-	500	-
Cl-6, Table -10 S. No- (ii), (Amendment No-1)("Shear strength a) Initial b) After 5 000 wear cycles")	-	800	-
Cl-6, Table -11 S. No- (i), (Amendment No-1)(Limit of useful extension)	-	800	-
Cl-6, Table -12 S. No- (i), (Amendment No-1)(Breaking strength of lace)	-	500	-
Cl-6, Table -12 S. No- (ii), (Amendment No-1)(Lace tag strength)	-	500	-
Cl-6, Table -12 S. No- (iii), (Amendment No-1)(Lace to lace abrasion)	-	600	-
Cl-6, Table -12 S. No (v), (Amendment No-1)(Strength of buckle/ski hook)	-	500	-
Cl-6, Table -12 S. No- (vi), (Amendment No-1)(Corrosion resistance)	-	800	-
Cl-6, Table -4 S. No- (i),(Amendment No-1)(Tear strength, N, Min)	-	450	-
Cl-6, Table -12 S. No- (iv), (Amendment No-1)(Colour fastness to water (for lace) (contact method))	-	600	-
Cl-6, Table -12 S. No- (iv), (Amendment No-1)(Colour fastness to water (for lace) (contact method))	-	600	-
Cl No.4.3(Whole Footwear)	-	640	-
Cl No.4.4 , Table No. 2 , v)(Stitch tear strength (double hole), N/mm, Min)	-	600	-
Cl No.4.5 , Table No. 3 , iv)("Colour fastness to perspiration (contact method) Grey scale rate, Min")	-	600	-
Cl No.4.6 , Table No. 4 , iii)(Abrasion resistance, at 400 cycles)	-	500	-
Cl No.4.9 , Table No. 7 , iii)(Heat shrinkage, percent, Max)	-	1200	-
Cl No.4.10 , Table No. 8 , ii)(Resilience, percent, Min)	-	400	-
Cl No.4.10 , Table No. 8 , iii)(Moisture resistance, percent, Min)	-	600	-
Cl No.4.12 , Table No. 10 , i)(Limit of useful extension, percent, Min)	-	600	-
Cl No.4.13 , Table No. 11 , i)(Breaking strength of lace, N, Min)	-	450	-
Cl No.4.13 , Table No. 11 , iii)(Lace to lace abrasion,)	-	600	-
Cl No . 5(MARKING AND PACKING)	-	200	-
Clause 4.3 - 4.3.1(Whole Footwear)	-	640	-
Clause 4.3 - 4.3.2(Whole Footwear)	-	640	-
Clause 4.4, Table 1 v)(Stitch Tear Strength(Double Hole))	-	600	-
Clause 4.9, Table 7 iii)(Heat shrinkage)	-	1200	-
Cl No.4.4 , Table No. 2 , i) , b)(Flexing resistance, Wet condition)	-	800	-
Cl-5, Table -1 S. No-(i) (Amendment No-1)(Insole)	-	200	-
Cl-5, Table -1 S. No- (ii) (Amendment No-1)(Toe spring height)	-	200	-
Cl-5, Table -1 S. No- (v) (Amendment No-1)(Complete shoe flexing)	-	640	-
Cl-6, Table -2 S. No- (iv),(Amendment No-1)(Stitch tear strength)	-	600	-
Cl-6, Table -4 S. No- (iii),(Amendment No-1)(Colour fastness to rubbing , grey scale rate with 10 rubs on dry or wet, Min)	-	600	-
Cl-6, Table -8 S. No- (iii), (Amendment No-1)(Heat shrinkage)	-	1200	-
Cl-6, Table -10 S. No- (ii), (Amendment No-1)("Shear strength a) Initial b) After 5 000 wear cycles")	-	600	-
Cl-6, Table -12 S. No- (i), (Amendment No-1)(Breaking strength of lace)	-	450	-
Cl-6, Table -12 S. No- (vi), (Amendment No-1)(Corrosion resistance)	-	600	-
Cl-6, Table -12 S. No- (iv), (Amendment No-1)(Colour fastness to water (for lace) (contact method))	-	500	-
Cl-6, Table -12 S. No- (iv), (Amendment No-1)(Colour fastness to water (for lace) (contact method))	-	500	-

02 Sep, 2027

-
Exclusion: Table-1 (vi), Table-1 (ix), Table-2 (v) & Table-1 (x)- Chemical Requirement, Table 1 xii Lead

6964

DELHI TEST HOUSE, Azadhpur

8131406

IS 737 (2024)

WROUGHT ALUMINIUM AND ALUMINIUM ALLOY SHEET AND STRIP FOR GENERAL ENGINEERING PURPOSES SPECIFICATION (Fifth Revision)

ALL

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 7(Chemical Composition - IS 504/ IS 504 (Part-1 to 12)/ IS 504 (Part-13 to 16)/ ASTM E 1251/ IS 11035)	-	7000	NA
Cl. 7(Si - IS 504 (Part-1)/ ASTM E 1251/ IS 11035)	-	500	NA
Cl. 7(Fe - IS 504 (Part-2)/ ASTM E 1251/ IS 11035)	-	500	NA
Cl. 7(Cu - IS 504 (Part-3)/ ASTM E 1251/ IS 11035)	-	500	NA
Cl. 7(Mn - IS 504 (Part-5)/ ASTM E 1251/ IS 11035)	-	500	NA
Cl. 7(Mg - IS 504 (Part-6)/ ASTM E 1251/ IS 11035)	-	500	NA
Cl. 7(Cr - IS 504 (Part-8)/ ASTM E 1251/ IS 11035)	-	500	NA
Cl. 7(Zn - IS 504 (Part-4)/ ASTM E 1251/ IS 11035)	-	500	NA
Cl. 7(Ti - IS 504 (Part-11)/ ASTM E 1251/ IS 11035)	-	500	NA
Cl. 7(Others (Each) - IS 504/ IS 504 (Part-1 to 12)/ IS 504 (Part-13 to 16)/ ASTM E 1251/ IS 11035)	-	5000	NA
Cl. 7(Others (Total) - IS 504/ IS 504 (Part-1 to 12)/ IS 504 (Part-13 to 16)/ ASTM E 1251/ IS 11035)	-	500	NA
Cl. 8(Mechanical Properties - IS 1608 (Part-1))	-	5000	NA
Cl. 8.1(0.2% Proof Stress - IS 1608 (Part-1))	-	2000	NA
Cl. 8.1(Tensile Strength - IS 1608 (Part-1))	-	2000	NA
Cl. 8.1(Elongation on 50mm Gauge Length - IS 1608 (Part-1))	-	1000	NA
Cl. 8.2(Bend Test - IS 1599)	-	1000	NA
Cl. 10(Dimensions and Tolerances - IS 737/ IS 2676)	-	1000	NA
Cl. 13.1(Marking - IS 737)	-	250	NA
Cl. 7(Al - IS 504)	-	500	NA
Cl. 4(Ordering Information - IS 737)	-	0	NA
Cl. 4 (a)(Grade/ Thickness - IS 737)	-	0	NA
Cl. 4 (b)(Condition - IS 737)	-	0	NA
Cl. 4 (c)(Quantity in Kg - IS 737)	-	0	NA
Cl. 4 (d)(Size - Thickness X Width X Length (T X W X L) in mm for sheets and (T X W) in mm for Strips/ Coils - IS 737)	-	0	NA
Cl. 4 (e)(Coil ID and Coil Weight for Strips/ Coils - IS 737)	-	0	NA
Cl. 4 (f)(Core/ Spool Requirement for Coils - IS 737)	-	0	NA
Cl. 4 (g)(Packing Mode - IS 737)	-	0	NA
Cl. 5(Supply for Material - IS 737/ IS 10259)	-	0	NA
Cl. 9(Condition - IS 737/ IS 5052)	-	0	NA
Cl. 11(Selection of Test Samples - IS 737)	-	0	NA
Cl. 11.1(Sheet and Strip of Aluminium or Non - Heat Treatable Aluminium Alloy - IS 737)	-	0	NA
Cl. 11.2(Sheet and Strip of Heat - Treatable Aluminium Alloys - IS 737)	-	0	NA
Cl. 12(Retests - IS 737/ IS 10259)	-	0	NA
Cl. 13(Packaging - IS 737/ IS 10259)	-	0	NA
Cl. 6(Freedom from Defects - IS 737)	-	250	NA

17 Jun, 2027

-
Included w.e.f.12.03.2025

6965

The Synthetic and Art Silk Mills' Research Association (SASMIRA), MUMBAI

7175004

IS 16513 (2016)

Agro textiles “ Insect nets for agriculture and horticulture purposes “ Specification

18500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6/6.1( REQUIREMENTS Dimensions and Mass a) Length)	-	400	-
6/6.1( REQUIREMENTS Dimensions and Mass b) width)	-	400	-
6/6.1( REQUIREMENTS Dimensions and Mass c) Mass gm/m2)	-	400	-
4.2( Netting Fabric)	-	200	-
4/4.1(b) percent on avarage value; and( MATERIAL / HDPE Monofilament Yarn)	-	400	-
4/4.1(a) percent on individual value; and( MATERIAL / HDPE Monofilament Yarn)	-	400	-
4.2( Netting Fabric)	-	200	-
4.2( Netting Fabric)	-	200	-
5.0(types a) Type I — having mesh of 30; b) Type II — having mesh of 40; andc) c) Type III — having mesh of 50)	-	2100	-
4/4.1.1/60°C / 95°C( MATERIAL / HDPE Monofilament Yarn)	-	1000	-
4.3( Colour)	-	0	-
6.2(Table-1)	-	12300	-
6.2/3(cover factor)	-	500	-

14 Dec, 2026

-
-

6966

Unique Test House LLP

9134536

IS 9295 (2024)

STEEL TUBES FOR IDLERS FOR BELT CONVEYORS - SPECIFICATION (second revision)

ALL GRADE TYPE DESIGNATION AND SIZE

7200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
As per Clause 5(Types /Grade and Designation)	-	500	-
As per clause 6(Material)	-	100	-
As per clause 7(Manufacture)	-	200	-
As per clause 7.1.5(Sulphur)	-	800	-
As per clause 7.1.6(Phosphorus)	-	800	-
As per clause 8(Mechanical Properties)	-	200	-
As per clause 8.1(Tensile Test)	-	700	-
As per clause 8.1.1(Yield Stress)	-	700	-
As per clause 8.1.2(Elongation)	-	700	-
As per clause 8.2(Drift Expansion Test)	-	1000	-
As per clause 8.3(Flattening Test)	-	1500	-
Cl-9.1, Table-2(Outside Diameter)	-	700	-
As per clause 10(Hardness Test)	-	1000	-
As per clause 11(Mechanical Test)	-	1500	-
As per clause 12(Retests)	-	1500	-
As per clause 13(Dimension Tolerance)	-	500	-
As per clause 14(Workmanship)	-	200	-
As per clause 15(Straightness)	-	800	-
As per clause 16(Length)	-	200	-
As per clause 17(Surface Protection)	-	500	-
As per clause 18(Marking)	-	500	-

07 Sep, 2028

-
-

6967

SIIR, Delhi Shriram Institute For Industrial Research

8102006

IS 16415 (2015)

Composite cement - Specification

Composite Cement

26000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Chemical Requirements)	-	0	-
7(Physical Requirement)	-	0	-
6 -Table - 2 i(Insoluble residue - Cl 4.10 of IS 4032:1985)	-	1000	30% Discount
6 -Table - 2 ii(Magnesia - Cl 4.8 of IS 4032:1985)	-	2000	30% Discount
6 -Table - 2 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-	1000	30% Discount
6 -Table - 2 iv(Sulphide sulphur (S) - Cl 6.12 of IS 4032:1985)	-	1000	30% Discount
6 -Table - 2 v(Loss on ignition - Cl 4.2 of IS 4032:1985)	-	1000	30% Discount
6 -Table - 2 vi(Chloride content - Cl 4.13 of IS 4032:1985)	-	1000	30% Discount
Cl. 6.1,Table 2(Alkali content)	-	2000	30% Discount
6 -Table - 2 i(Insoluble residue - Cl 4.10 of IS 4032:1985)	-	0	-
6 -Table - 2 ii(Magnesia - Cl 4.8 of IS 4032:1985)	-	0	-
6 -Table - 2 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-	0	-
6 -Table - 2 iv(Sulphide sulphur (S) - Cl 6.12 of IS 4032:1985)	-	0	-
6 -Table - 2 v(Loss on ignition - Cl 4.2 of IS 4032:1985)	-	0	-
6 -Table - 2 vi(Chloride content - Cl 4.13 of IS 4032:1985)	-	0	-
Cl. 6.1,Table 2(Chloride content)	-	0	-
Cl. 6.1,Table 2(Loss on ignition)	-	0	-
Cl. 6.1,Table 2(Suilphide sulphur)	-	0	-
Cl. 6.1,Table 2(Total sulphur content calculated as sulphuric anhydride)	-	0	-
Cl. 6.1,Table 2(Magnesia)	-	0	-
Cl. 6.1,Table 2(Insoluble residue)	-	0	-
7 and Table 3 i(Fineness IS 4031(Part 2))	-	1000	30% Discount
7 and Table 3 ii a(Soundness, Le-Chate1ier expansion IS 4031(Part 3) )	-	1000	30% Discount
7 and Table 3 ii b(Soundness, Autoclave expansion IS 4031(Part 3) )	-	1000	30% Discount
7 and Table 3 iii a(Setting Time ( by Vicat Apparatus), Initial IS 4031(Part 5))	-	500	30% Discount
7 and Table 3 iii b(Setting Time ( by Vicat Apparatus ), Final IS 4031(Part 5))	-	500	30% Discount
7 and Table 3 iv a(Compretsive Strenqth .72 ± 1 hr IS 4031(Part 6))	-	5000	30% Discount
7 and Table 3 iv b(Compretsive Strenqth 168 ± 2 hr IS 4031(Part 6))	-	0	-
7 and Table 3 iv c(Compretsive Strenqth 672 ± 4 hr IS 4031(Part 6))	-	0	-
7 and Table 3 v(Drying shrinkage IS 4031(Part 10))	-	3000	30% Discount
7 and Table 3 vi(Transverse strength (optional) IS 4031(Part 8) )	-	5000	30% Discount
7 and Table 3 i(Fineness IS 4031(Part 2))	-	0	-
7 and Table 3 ii a(Soundness, Le-Chate1ier expansion IS 4031(Part 3) )	-	0	-
7 and Table 3 ii b(Soundness, Autoclave expansion IS 4031(Part 3) )	-	0	-
7 and Table 3 iii a(Setting Time ( by Vicat Apparatus), Initial IS 4031(Part 5))	-	0	-
7 and Table 3 iii b(Setting Time ( by Vicat Apparatus ), Final IS 4031(Part 5))	-	0	-
7 and Table 3 iv a(Compretsive Strenqth .72 ± 1 hr IS 4031(Part 6))	-	0	-
7 and Table 3 iv b(Compretsive Strenqth 168 ± 2 hr IS 4031(Part 6))	-	0	-
7 and Table 3 iv c(Compretsive Strenqth 672 ± 4 hr IS 4031(Part 6))	-	0	-
7 and Table 3 v(Drying shrinkage IS 4031(Part 10))	-	0	-
7 and Table 3 vi(Transverse strength (optional) IS 4031(Part 8) )	-	0	-
6(Chemical Requirements)	-	0	-
7(Physical Requirement)	-	0	-
Cl. 6.1,Table 2(Alkali content)	-	0	-
Cl. 6.1,Table 2(Chloride content)	-	0	-
Cl. 6.1,Table 2(Loss on ignition)	-	0	-
Cl. 6.1,Table 2(Suilphide sulphur)	-	0	-
Cl. 6.1,Table 2(Total sulphur content calculated as sulphuric anhydride)	-	0	-
Cl. 6.1,Table 2(Magnesia)	-	0	-
Cl. 6.1,Table 2(Insoluble residue)	-	0	-

31 Dec, 2026

-
Included w.e.f.12.03.2025

6968

INDIAN TESTING LABORATORY PRIVATE LIMITED, GREATER NOIDA

8171306

IS 1285 (2023)

WROUGHT ALUMINIUM AND ALUMINIUM ALLOYS EXTRUDED ROUND TUBE AND HOLLOW SECTIONS FOR GENERAL ENGINEERINGPURPOSES SPECIFICATION

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1("The extruded round tube and hollow sections shall be sound and visually free from harmful defects. ")	-	500	-
6.2(Slight discoloration due to heat treatment, minor polishing marks and spiral marks due to roll straightening shall not be a cause for rejection.)	-	500	-
8("Dimensions and tolerances of the material shall be as laid down in the Indian Standards indicated below: a) Extruded round tube IS 2673; and b) Extruded hollow sections IS 6477.")	-	1000	-
9(" Extruded round tubes and hollow sections shall be made from alloys specified in IS 733. 9.2 The chemical analysis of the material shall be carried out either in accordance with the methods specified in IS 504 (Part 1 to 12) and IS 504 (Part 13 to 16) or by any other established instrumental/chemical method. In case of any dispute the method specified in relevant parts of IS 504 shall be used as referee method. However, when the method is not given in IS 504, the referee method shall be as agreed to between the purchaser and the manufacturer. ")	-	500	-
10(Tensile test)	-	1000	-
Cl.9.1(Aluminium- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Copper- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Magnesium- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Silicon- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Iron- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Manganese- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Zinc- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Titanium and/ or other grain refining elements- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Chromium- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Remarks (Ti+V) - IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Remarks (Cr+Mn) - IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Remarks (Total Impurities)- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-

15 Aug, 2028

-
Included w.e.f 12.03.2025

6969

VARDAN ENVIROLAB, GURUGRAM

8169616

IS 3736 (1995)

Canvas boots, rubber sole - Specification (Second Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4.1.7.4 Ageing(The boots shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the soles and heels of the boots shall conform to the physical requirements prescribed in Table 5. i) Tensile Length)	-	500	-
Cl.4.1.7.4 Ageing(ii) Elongation at break)	-	500	-
Cl.4.1.7.2 IS 3400 (Part 2) : 1980(2)Hardness, IRHD)	-	500	-
4.1.6 Fabric Laces Cl.4.1.6.1( The boots shall be provided with braided of cotton or man made or blended fabric laces 115 ± 5 cm in length, matching the colour of the upper. )	-	1000	-
Cl.4.1.1 upper IS 1969(d) Picks/dm)	-	500	-
Cl.4.4.5 ( Table 1.)(d) Picks/dm)	-	500	-
4.1.2 Lining Material(195 ± 5 picks/dm shall be used.)	-	500	-
Cl.4.1.1 upper IS 1969(c) Ends/dm )	-	500	-
Cl.4.4.5 ( Table 1.)(c) Ends/dm )	-	500	-
4.1.2 Lining Material(having 390 ± 10 ends/dm and )	-	500	-
Cl.4.1.7.2 IS 3400 (Part 4) : 1987 IS 3400 (Part 2) : 1980(Change in initial hardness after accelerated ageing for 24 h at l00 ± 1°C)	-	500	-
Cl.4.8 Adhesion Test(From the upper foxing portion where it is adhered to the canvas cut a strip of 8.0 ± 0.5 mm width along with the length of the sole at the waist portion and of sufficient lengh to permit separation over a length of at least 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10 mm per minute in accordance with IS 3400 (Part 5):1986 or the Static Dead Load Method as given in Annex C. The individual adhesion value noted/recorded shall not be less than 8 N (0.8 kgf) for each of the test pieces ( see Note under 4.7 ).')	-	1000	-
Cl.4.4.9(From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine)	-	500	-
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Tensile strength in MPa, Min)	-	500	-
Cl.4.1.3 Binding Material IS 1954:1990(Cotton tape NEWAR used as binding material shall conform to the requirements as mentioned in Table 2, when tested in accordance with the methods referred to in col 4 of Table 2. 1)Width, mm. Min )	-	500	-
Cl.4.4.3(The top, side and front edges of the quarters and tongue shall be bound with cotton tape NEWAR of not less than 13 mm width using variety No. 29 thread.)	-	500	-
Cl.4.1.7.3 IS 3400 (Part 10) : 1977(Compression set, in percent. Max)	-	500	-
Cl.4.4.4( The back of the quarter shall be reinforced with a strip, not less than 25 mm wide,of either upper material or canvas. In case of composite upper material the edges of the strip shall be bound by cotton tape ( NEWAR ). When canvas cloth is used the edges shall be folded and shall be stitched with two rows of stitching.)	-	500	-
Cl.4.7 Consolidation Test(From the quarter, cut a strip of 25.0 ± 0. 5 mm width along the length of the boot and of sufficient length to permit separation over a length of 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10mm per minute in accordance with IS 3400 (Part 5): 1986 or Static Dead Load Method as given in Annex C. The individual adhesion value for consolidation test shall not be less than 30 N (3.0 kgf) for each of the test pieces)	-	1000	-
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Elongation at break, in percent, Min)	-	500	-
IS 1969:1985(Breaking load on 50 cm test length. N, Min)	-	500	-
4.1.6 Fabric Laces Cl.4.1.6.1(The laces shall have a minimum breaking load of 450 N, when tested between 18 cm grips, the rate of traverse of power actuated grip being 30 cm/min.)	-	500	-
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles b)Cut growth at the end of 150 000 cycles, Percent, Max)	-	500	-
Cl.4.4.5 ( Table 1.)(b) Weft )	-	500	-
Cl.4.4.5 ( Table 1.)( in case of half bellow. Thefull bellow tongue shall be made out of canvas cloth as prescribed in Sl No. (i) of Table 1. Breaking load in N, Min a) Warp )	-	500	-
Cl.4.1.1 upper IS 1969(b)Weft)	-	500	-
Cl.4.1.1 upper IS 1969(Breaking load in N.Min (5 × 20 cm grip): a) Wrap)	-	500	-
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles a)Initial crack, Min)	-	500	-
4.1.2 Lining Material( 200 N Minin weft way (when tested in accordance with IS 1969 : 1985) )	-	500	-
4.1.2 Lining Material(For covering of the insole, cotton drill conforming to Table 1, Sl No. (ii) shall be used. For detachable insole, bleached cotton twill of breaking load 390 N Min in warp way and)	-	500	-
Cl.4.1.1 upper(The upper shall consist of Rip Stop Fabric of cotton or manmade or its blend being the over layer and cotton drill as an inner layer and shall conform to the requirements given at Sl No. (i) of Table 1. Sr.no 1.Overlayer Construction )	-	500	-
4.1.1.1 Colour fastness(The dyed fabrics prescribed in 4.1.1 shall be fast to daylight and mechanical washing. Fastness to daylight shall be of rating 4 or better, when tested in accordance with IS 686 : 1985 or IS 2454 : 1985.)	-	500	-
Cl.4.1.1.2( Fastness to mechanical washing (mild) shall be of rating 4 or better, when tested in accordance with IS 764 : 1979)	-	500	-
Cl.4.1.3.3( Black tapes shall be free from sulphur dyes when tested in accordance with Annex B.)	-	500	-
Cl.4.1.4 Reinforcement Material(The back seam, joining two quarters at the back of the heel shall be reinforced with a not less than 25 mm wide tape made out of material conforming to Sl No. (i) of Table 1)	-	500	-
Cl.4.1.5 Thread for Upper Closing Cl.4.1.5.1 (IS 1670:1991)(Sewing thread cotton, man made or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirements. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirement of specification.')	-	500	-
Cl.4.1.5.2( The colour of the threads shall be asagreed to between the purchaser and the supplier. The dyed threads shall conform to the following requirements)	-	500	-
4.1.6 Fabric Laces Cl.4.1.6.1(The two ends of the lace shall be provided with suitable metal or plastic tips. Black laces shall be free from sulphur dyes when tested in accordance with Annex B.)	-	500	-
Cl.4.1.7 Rubber Components Cl.4.1.7.1( the soles and heels shall conform to Type 2 of IS 5676:1995.)	-	500	-
Cl.4.1.7.2 IS 3400 (Part 9) : 1978( The rubber components shall conform to Table 4 when tested.' ( Page 3, Table 4, Note 1) — 'However in case it is not possible then 4.2.5.3 of IS 13695:1993 shall be followed. 1)Relative density, Max)	-	500	-
Cl.4.1.7.5 Thickness of components(Individual components of the boots shall comply with the thickness and material requirements prescribed in Table 6.)	-	500	-
Cl.4.3 Leg Height(The leg height of the boots for size 8 shall be 160 ± 2 mm with an increase or decrease of 4 mm of the nominal height for each bigger or smaller sizes respectively when measured at the inside from the back of the boot from insole to the top.)	-	500	-
Cl.4.4.2( The canvas upper shall be lined with bleached drill cloth.)	-	500	-
Cl.4.4.3( The upper shall be stitched on a lockstitch machine, with 30 to 40 stitches per decimetre by thread of variety No. 8 and variety No. 29 cotton sewing thread conforming to 4.1.5 using variety No. 29 for taping and binding and variety No. 8 for remaining seams. )	-	500	-
Cl.4.4.5 ( The tongue shall be either half or full bellow depending on the requirement of the purchaser andshall be made from composite material prescribed for the upper in 4.1.1.)	-	500	-
Cl.4.4.6( A minimum of seven aluminium, brass or steel eyelets having 10 mm diameter and wall thickness 0.30 to 0.35 mm shall be fitted in each face.')	-	500	-
Cl.4.4.7( The toe shall be reinforced with a toe puff cemented inside and outside with rubber toe cap. The heel piece (counter) or stiffener shall be set from the bottom of the lining and bound flat on the top edge with white cloth for binding of countertop edge with white clothfor binding of counter)	-	500	-
Cl.4.4.8( A strengthening rubber arch piece shall be firmly pasted and stitched at the middle arch of the inside quarter. Another strengthening rubber piece, circular in shape 35 ± 1 mm in diameter, may bepasted and stitched at the centre of the inside)	-	500	-
Cl.4.4.10( A 25 mm Min wide and 2 mm Min thick rubber golosh in serrated, diamond or any otherdesign, as agreed to between the purchaser and thesupplier, shall be fitted all round the sole edge of the boot. The golosh shall not extend below the edge of the sole.)	-	500	-
Cl.4.5.1(Cl.4.1.6.)( Each pair of boot shall be provided with a pair of braided fabric laces of the quality as prescribed in 4.1.6.)	-	500	-
Cl.4.5.2( In appearance, general workmanship, finish and in all other respects, not defined in this standard, the boot shall be similar to those of the sample approved by the purchaser, if any.)	-	500	-
Cl.4.6 Mass(The mass of finished boots, rubber sole, of size 8 shall not exceed 1130 g per pair, and the mass shall increase or decrease by 75 g per pair for each bigger or smaller size respectively.)	-	500	-
Cl.4.9 Composite Breaking Strength Test( From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine.Rate of traverse of pulling jaw shall be 100 ± 5 mm per minute. Two such test pieces will be required to be obtained from the made up footwear and will be subjected to test to break each test piece. Mean value of each set of test pieces comprising of length wise and height wise test pieces will be 1 000 N/25 mm width minimum.')	-	500	-
Cl.4.1.7.4 Ageing(The boots shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the soles and heels of the boots shall conform to the physical requirements prescribed in Table 5. i) Tensile Length)	-	0	PARAMETER REPEAT
Cl.4.1.7.4 Ageing(ii) Elongation at break)	-	0	PARAMETER REPEAT
Cl.4.1.7.2 IS 3400 (Part 2) : 1980(2)Hardness, IRHD)	-	0	PARAMETER REPEAT
4.1.6 Fabric Laces Cl.4.1.6.1( The boots shall be provided with braided of cotton or man made or blended fabric laces 115 ± 5 cm in length, matching the colour of the upper. )	-	0	PARAMETER REPEAT
Cl.4.1.1 upper IS 1969(d) Picks/dm)	-	0	PARAMETER REPEAT
Cl.4.4.5 ( Table 1.)(d) Picks/dm)	-	0	PARAMETER REPEAT
4.1.2 Lining Material(195 ± 5 picks/dm shall be used.)	-	0	PARAMETER REPEAT
Cl.4.1.1 upper IS 1969(c) Ends/dm )	-	0	PARAMETER REPEAT
Cl.4.4.5 ( Table 1.)(c) Ends/dm )	-	0	PARAMETER REPEAT
4.1.2 Lining Material(having 390 ± 10 ends/dm and )	-	0	PARAMETER REPEAT
Cl.4.1.7.2 IS 3400 (Part 4) : 1987 IS 3400 (Part 2) : 1980(Change in initial hardness after accelerated ageing for 24 h at l00 ± 1°C)	-	0	PARAMETER REPEAT
Cl.4.8 Adhesion Test(From the upper foxing portion where it is adhered to the canvas cut a strip of 8.0 ± 0.5 mm width along with the length of the sole at the waist portion and of sufficient lengh to permit separation over a length of at least 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10 mm per minute in accordance with IS 3400 (Part 5):1986 or the Static Dead Load Method as given in Annex C. The individual adhesion value noted/recorded shall not be less than 8 N (0.8 kgf) for each of the test pieces ( see Note under 4.7 ).')	-	0	PARAMETER REPEAT
Cl.4.4.9(From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine)	-	0	PARAMETER REPEAT
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Tensile strength in MPa, Min)	-	0	PARAMETER REPEAT
Cl.4.1.3 Binding Material IS 1954:1990(Cotton tape NEWAR used as binding material shall conform to the requirements as mentioned in Table 2, when tested in accordance with the methods referred to in col 4 of Table 2. 1)Width, mm. Min )	-	0	PARAMETER REPEAT
Cl.4.4.3(The top, side and front edges of the quarters and tongue shall be bound with cotton tape NEWAR of not less than 13 mm width using variety No. 29 thread.)	-	0	PARAMETER REPEAT
Cl.4.1.7.3 IS 3400 (Part 10) : 1977(Compression set, in percent. Max)	-	0	PARAMETER REPEAT
Cl.4.4.4( The back of the quarter shall be reinforced with a strip, not less than 25 mm wide,of either upper material or canvas. In case of composite upper material the edges of the strip shall be bound by cotton tape ( NEWAR ). When canvas cloth is used the edges shall be folded and shall be stitched with two rows of stitching.)	-	0	PARAMETER REPEAT
Cl.4.7 Consolidation Test(From the quarter, cut a strip of 25.0 ± 0. 5 mm width along the length of the boot and of sufficient length to permit separation over a length of 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10mm per minute in accordance with IS 3400 (Part 5): 1986 or Static Dead Load Method as given in Annex C. The individual adhesion value for consolidation test shall not be less than 30 N (3.0 kgf) for each of the test pieces)	-	0	PARAMETER REPEAT
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Elongation at break, in percent, Min)	-	0	PARAMETER REPEAT
IS 1969:1985(Breaking load on 50 cm test length. N, Min)	-	0	PARAMETER REPEAT
4.1.6 Fabric Laces Cl.4.1.6.1(The laces shall have a minimum breaking load of 450 N, when tested between 18 cm grips, the rate of traverse of power actuated grip being 30 cm/min.)	-	0	PARAMETER REPEAT
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles b)Cut growth at the end of 150 000 cycles, Percent, Max)	-	0	PARAMETER REPEAT
Cl.4.4.5 ( Table 1.)(b) Weft )	-	0	PARAMETER REPEAT
Cl.4.4.5 ( Table 1.)( in case of half bellow. Thefull bellow tongue shall be made out of canvas cloth as prescribed in Sl No. (i) of Table 1. Breaking load in N, Min a) Warp )	-	0	PARAMETER REPEAT
Cl.4.1.1 upper IS 1969(b)Weft)	-	0	PARAMETER REPEAT
Cl.4.1.1 upper IS 1969(Breaking load in N.Min (5 × 20 cm grip): a) Wrap)	-	0	PARAMETER REPEAT
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles a)Initial crack, Min)	-	0	PARAMETER REPEAT
4.1.2 Lining Material( 200 N Minin weft way (when tested in accordance with IS 1969 : 1985) )	-	0	PARAMETER REPEAT
4.1.2 Lining Material(For covering of the insole, cotton drill conforming to Table 1, Sl No. (ii) shall be used. For detachable insole, bleached cotton twill of breaking load 390 N Min in warp way and)	-	0	PARAMETER REPEAT
Cl.4.1.1 upper(The upper shall consist of Rip Stop Fabric of cotton or manmade or its blend being the over layer and cotton drill as an inner layer and shall conform to the requirements given at Sl No. (i) of Table 1. Sr.no 1.Overlayer Construction )	-	0	PARAMETER REPEAT
4.1.1.1 Colour fastness(The dyed fabrics prescribed in 4.1.1 shall be fast to daylight and mechanical washing. Fastness to daylight shall be of rating 4 or better, when tested in accordance with IS 686 : 1985 or IS 2454 : 1985.)	-	0	PARAMETER REPEAT
Cl.4.1.1.2( Fastness to mechanical washing (mild) shall be of rating 4 or better, when tested in accordance with IS 764 : 1979)	-	0	PARAMETER REPEAT
Cl.4.1.3.3( Black tapes shall be free from sulphur dyes when tested in accordance with Annex B.)	-	0	PARAMETER REPEAT
Cl.4.1.4 Reinforcement Material(The back seam, joining two quarters at the back of the heel shall be reinforced with a not less than 25 mm wide tape made out of material conforming to Sl No. (i) of Table 1)	-	0	PARAMETER REPEAT
Cl.4.1.5 Thread for Upper Closing Cl.4.1.5.1 (IS 1670:1991)(Sewing thread cotton, man made or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirements. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirement of specification.')	-	0	PARAMETER REPEAT
Cl.4.1.5.2( The colour of the threads shall be asagreed to between the purchaser and the supplier. The dyed threads shall conform to the following requirements)	-	0	PARAMETER REPEAT
4.1.6 Fabric Laces Cl.4.1.6.1(The two ends of the lace shall be provided with suitable metal or plastic tips. Black laces shall be free from sulphur dyes when tested in accordance with Annex B.)	-	0	PARAMETER REPEAT
Cl.4.1.7 Rubber Components Cl.4.1.7.1( the soles and heels shall conform to Type 2 of IS 5676:1995.)	-	0	PARAMETER REPEAT
Cl.4.1.7.2 IS 3400 (Part 9) : 1978( The rubber components shall conform to Table 4 when tested.' ( Page 3, Table 4, Note 1) — 'However in case it is not possible then 4.2.5.3 of IS 13695:1993 shall be followed. 1)Relative density, Max)	-	0	PARAMETER REPEAT
Cl.4.1.7.5 Thickness of components(Individual components of the boots shall comply with the thickness and material requirements prescribed in Table 6.)	-	0	PARAMETER REPEAT
Cl.4.3 Leg Height(The leg height of the boots for size 8 shall be 160 ± 2 mm with an increase or decrease of 4 mm of the nominal height for each bigger or smaller sizes respectively when measured at the inside from the back of the boot from insole to the top.)	-	0	PARAMETER REPEAT
Cl.4.4.2( The canvas upper shall be lined with bleached drill cloth.)	-	0	PARAMETER REPEAT
Cl.4.4.3( The upper shall be stitched on a lockstitch machine, with 30 to 40 stitches per decimetre by thread of variety No. 8 and variety No. 29 cotton sewing thread conforming to 4.1.5 using variety No. 29 for taping and binding and variety No. 8 for remaining seams. )	-	0	PARAMETER REPEAT
Cl.4.4.5 ( The tongue shall be either half or full bellow depending on the requirement of the purchaser andshall be made from composite material prescribed for the upper in 4.1.1.)	-	0	PARAMETER REPEAT
Cl.4.4.6( A minimum of seven aluminium, brass or steel eyelets having 10 mm diameter and wall thickness 0.30 to 0.35 mm shall be fitted in each face.')	-	0	PARAMETER REPEAT
Cl.4.4.7( The toe shall be reinforced with a toe puff cemented inside and outside with rubber toe cap. The heel piece (counter) or stiffener shall be set from the bottom of the lining and bound flat on the top edge with white cloth for binding of countertop edge with white clothfor binding of counter)	-	0	PARAMETER REPEAT
Cl.4.4.8( A strengthening rubber arch piece shall be firmly pasted and stitched at the middle arch of the inside quarter. Another strengthening rubber piece, circular in shape 35 ± 1 mm in diameter, may bepasted and stitched at the centre of the inside)	-	0	PARAMETER REPEAT
Cl.4.4.10( A 25 mm Min wide and 2 mm Min thick rubber golosh in serrated, diamond or any otherdesign, as agreed to between the purchaser and thesupplier, shall be fitted all round the sole edge of the boot. The golosh shall not extend below the edge of the sole.)	-	0	PARAMETER REPEAT
Cl.4.5.1(Cl.4.1.6.)( Each pair of boot shall be provided with a pair of braided fabric laces of the quality as prescribed in 4.1.6.)	-	0	PARAMETER REPEAT
Cl.4.5.2( In appearance, general workmanship, finish and in all other respects, not defined in this standard, the boot shall be similar to those of the sample approved by the purchaser, if any.)	-	0	PARAMETER REPEAT
Cl.4.6 Mass(The mass of finished boots, rubber sole, of size 8 shall not exceed 1130 g per pair, and the mass shall increase or decrease by 75 g per pair for each bigger or smaller size respectively.)	-	0	PARAMETER REPEAT
Cl.4.9 Composite Breaking Strength Test( From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine.Rate of traverse of pulling jaw shall be 100 ± 5 mm per minute. Two such test pieces will be required to be obtained from the made up footwear and will be subjected to test to break each test piece. Mean value of each set of test pieces comprising of length wise and height wise test pieces will be 1 000 N/25 mm width minimum.')	-	0	PARAMETER REPEAT
Cl.4.1.7.4 Ageing(The boots shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the soles and heels of the boots shall conform to the physical requirements prescribed in Table 5. i) Tensile Length)	-	0	PARAMETER REPEAT
Cl.4.1.7.4 Ageing(ii) Elongation at break)	-	0	PARAMETER REPEAT
Cl.4.1.7.2 IS 3400 (Part 2) : 1980(2)Hardness, IRHD)	-	0	PARAMETER REPEAT
4.1.6 Fabric Laces Cl.4.1.6.1( The boots shall be provided with braided of cotton or man made or blended fabric laces 115 ± 5 cm in length, matching the colour of the upper. )	-	0	PARAMETER REPEAT
Cl.4.1.1 upper IS 1969(d) Picks/dm)	-	0	PARAMETER REPEAT
Cl.4.4.5 ( Table 1.)(d) Picks/dm)	-	0	PARAMETER REPEAT
4.1.2 Lining Material(195 ± 5 picks/dm shall be used.)	-	0	PARAMETER REPEAT
Cl.4.1.1 upper IS 1969(c) Ends/dm )	-	0	PARAMETER REPEAT
Cl.4.4.5 ( Table 1.)(c) Ends/dm )	-	0	PARAMETER REPEAT
4.1.2 Lining Material(having 390 ± 10 ends/dm and )	-	0	PARAMETER REPEAT
Cl.4.1.7.2 IS 3400 (Part 4) : 1987 IS 3400 (Part 2) : 1980(Change in initial hardness after accelerated ageing for 24 h at l00 ± 1°C)	-	0	PARAMETER REPEAT
Cl.4.8 Adhesion Test(From the upper foxing portion where it is adhered to the canvas cut a strip of 8.0 ± 0.5 mm width along with the length of the sole at the waist portion and of sufficient lengh to permit separation over a length of at least 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10 mm per minute in accordance with IS 3400 (Part 5):1986 or the Static Dead Load Method as given in Annex C. The individual adhesion value noted/recorded shall not be less than 8 N (0.8 kgf) for each of the test pieces ( see Note under 4.7 ).')	-	0	PARAMETER REPEAT
Cl.4.4.9(From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine)	-	0	PARAMETER REPEAT
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Tensile strength in MPa, Min)	-	0	PARAMETER REPEAT
Cl.4.1.3 Binding Material IS 1954:1990(Cotton tape NEWAR used as binding material shall conform to the requirements as mentioned in Table 2, when tested in accordance with the methods referred to in col 4 of Table 2. 1)Width, mm. Min )	-	0	PARAMETER REPEAT
Cl.4.4.3(The top, side and front edges of the quarters and tongue shall be bound with cotton tape NEWAR of not less than 13 mm width using variety No. 29 thread.)	-	0	PARAMETER REPEAT
Cl.4.1.7.3 IS 3400 (Part 10) : 1977(Compression set, in percent. Max)	-	0	PARAMETER REPEAT
Cl.4.4.4( The back of the quarter shall be reinforced with a strip, not less than 25 mm wide,of either upper material or canvas. In case of composite upper material the edges of the strip shall be bound by cotton tape ( NEWAR ). When canvas cloth is used the edges shall be folded and shall be stitched with two rows of stitching.)	-	0	PARAMETER REPEAT
Cl.4.7 Consolidation Test(From the quarter, cut a strip of 25.0 ± 0. 5 mm width along the length of the boot and of sufficient length to permit separation over a length of 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10mm per minute in accordance with IS 3400 (Part 5): 1986 or Static Dead Load Method as given in Annex C. The individual adhesion value for consolidation test shall not be less than 30 N (3.0 kgf) for each of the test pieces)	-	0	PARAMETER REPEAT
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Elongation at break, in percent, Min)	-	0	PARAMETER REPEAT
IS 1969:1985(Breaking load on 50 cm test length. N, Min)	-	0	PARAMETER REPEAT
4.1.6 Fabric Laces Cl.4.1.6.1(The laces shall have a minimum breaking load of 450 N, when tested between 18 cm grips, the rate of traverse of power actuated grip being 30 cm/min.)	-	0	PARAMETER REPEAT
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles b)Cut growth at the end of 150 000 cycles, Percent, Max)	-	0	PARAMETER REPEAT
Cl.4.4.5 ( Table 1.)(b) Weft )	-	0	PARAMETER REPEAT
Cl.4.4.5 ( Table 1.)( in case of half bellow. Thefull bellow tongue shall be made out of canvas cloth as prescribed in Sl No. (i) of Table 1. Breaking load in N, Min a) Warp )	-	0	PARAMETER REPEAT
Cl.4.1.1 upper IS 1969(b)Weft)	-	0	PARAMETER REPEAT
Cl.4.1.1 upper IS 1969(Breaking load in N.Min (5 × 20 cm grip): a) Wrap)	-	0	PARAMETER REPEAT
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles a)Initial crack, Min)	-	0	PARAMETER REPEAT
4.1.2 Lining Material( 200 N Minin weft way (when tested in accordance with IS 1969 : 1985) )	-	0	PARAMETER REPEAT
4.1.2 Lining Material(For covering of the insole, cotton drill conforming to Table 1, Sl No. (ii) shall be used. For detachable insole, bleached cotton twill of breaking load 390 N Min in warp way and)	-	0	PARAMETER REPEAT
Cl.4.1.1 upper(The upper shall consist of Rip Stop Fabric of cotton or manmade or its blend being the over layer and cotton drill as an inner layer and shall conform to the requirements given at Sl No. (i) of Table 1. Sr.no 1.Overlayer Construction )	-	0	PARAMETER REPEAT
4.1.1.1 Colour fastness(The dyed fabrics prescribed in 4.1.1 shall be fast to daylight and mechanical washing. Fastness to daylight shall be of rating 4 or better, when tested in accordance with IS 686 : 1985 or IS 2454 : 1985.)	-	0	PARAMETER REPEAT
Cl.4.1.1.2( Fastness to mechanical washing (mild) shall be of rating 4 or better, when tested in accordance with IS 764 : 1979)	-	0	PARAMETER REPEAT
Cl.4.1.3.3( Black tapes shall be free from sulphur dyes when tested in accordance with Annex B.)	-	0	PARAMETER REPEAT
Cl.4.1.4 Reinforcement Material(The back seam, joining two quarters at the back of the heel shall be reinforced with a not less than 25 mm wide tape made out of material conforming to Sl No. (i) of Table 1)	-	0	PARAMETER REPEAT
Cl.4.1.5 Thread for Upper Closing Cl.4.1.5.1 (IS 1670:1991)(Sewing thread cotton, man made or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirements. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirement of specification.')	-	0	PARAMETER REPEAT
Cl.4.1.5.2( The colour of the threads shall be asagreed to between the purchaser and the supplier. The dyed threads shall conform to the following requirements)	-	0	PARAMETER REPEAT
4.1.6 Fabric Laces Cl.4.1.6.1(The two ends of the lace shall be provided with suitable metal or plastic tips. Black laces shall be free from sulphur dyes when tested in accordance with Annex B.)	-	0	PARAMETER REPEAT
Cl.4.1.7 Rubber Components Cl.4.1.7.1( the soles and heels shall conform to Type 2 of IS 5676:1995.)	-	0	PARAMETER REPEAT
Cl.4.1.7.2 IS 3400 (Part 9) : 1978( The rubber components shall conform to Table 4 when tested.' ( Page 3, Table 4, Note 1) — 'However in case it is not possible then 4.2.5.3 of IS 13695:1993 shall be followed. 1)Relative density, Max)	-	0	PARAMETER REPEAT
Cl.4.1.7.5 Thickness of components(Individual components of the boots shall comply with the thickness and material requirements prescribed in Table 6.)	-	0	PARAMETER REPEAT
Cl.4.3 Leg Height(The leg height of the boots for size 8 shall be 160 ± 2 mm with an increase or decrease of 4 mm of the nominal height for each bigger or smaller sizes respectively when measured at the inside from the back of the boot from insole to the top.)	-	0	PARAMETER REPEAT
Cl.4.4.2( The canvas upper shall be lined with bleached drill cloth.)	-	0	PARAMETER REPEAT
Cl.4.4.3( The upper shall be stitched on a lockstitch machine, with 30 to 40 stitches per decimetre by thread of variety No. 8 and variety No. 29 cotton sewing thread conforming to 4.1.5 using variety No. 29 for taping and binding and variety No. 8 for remaining seams. )	-	0	PARAMETER REPEAT
Cl.4.4.5 ( The tongue shall be either half or full bellow depending on the requirement of the purchaser andshall be made from composite material prescribed for the upper in 4.1.1.)	-	0	PARAMETER REPEAT
Cl.4.4.6( A minimum of seven aluminium, brass or steel eyelets having 10 mm diameter and wall thickness 0.30 to 0.35 mm shall be fitted in each face.')	-	0	PARAMETER REPEAT
Cl.4.4.7( The toe shall be reinforced with a toe puff cemented inside and outside with rubber toe cap. The heel piece (counter) or stiffener shall be set from the bottom of the lining and bound flat on the top edge with white cloth for binding of countertop edge with white clothfor binding of counter)	-	0	PARAMETER REPEAT
Cl.4.4.8( A strengthening rubber arch piece shall be firmly pasted and stitched at the middle arch of the inside quarter. Another strengthening rubber piece, circular in shape 35 ± 1 mm in diameter, may bepasted and stitched at the centre of the inside)	-	0	PARAMETER REPEAT
Cl.4.4.10( A 25 mm Min wide and 2 mm Min thick rubber golosh in serrated, diamond or any otherdesign, as agreed to between the purchaser and thesupplier, shall be fitted all round the sole edge of the boot. The golosh shall not extend below the edge of the sole.)	-	0	PARAMETER REPEAT
Cl.4.5.1(Cl.4.1.6.)( Each pair of boot shall be provided with a pair of braided fabric laces of the quality as prescribed in 4.1.6.)	-	0	PARAMETER REPEAT
Cl.4.5.2( In appearance, general workmanship, finish and in all other respects, not defined in this standard, the boot shall be similar to those of the sample approved by the purchaser, if any.)	-	0	PARAMETER REPEAT
Cl.4.6 Mass(The mass of finished boots, rubber sole, of size 8 shall not exceed 1130 g per pair, and the mass shall increase or decrease by 75 g per pair for each bigger or smaller size respectively.)	-	0	PARAMETER REPEAT
Cl.4.9 Composite Breaking Strength Test( From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine.Rate of traverse of pulling jaw shall be 100 ± 5 mm per minute. Two such test pieces will be required to be obtained from the made up footwear and will be subjected to test to break each test piece. Mean value of each set of test pieces comprising of length wise and height wise test pieces will be 1 000 N/25 mm width minimum.')	-	0	PARAMETER REPEAT
4.1.3.2(Fastness to mechanical washing (mild))	-	500	-
4.1.3(Cotton tape NEWAR)	-	200	-
Table 2 (ii)(Breaking load on 50 cm test length. N, Min)	-	500	-
4.1.6.2(Laces- Fastness to daylight)	-	500	-
4.1.6.3(Laces- Fastness to mechanical washing (mild))	-	500	-

26 Dec, 2027

-
Included w.e.f.17.06.2025

6970

Hi Physix Laboratory India Private Limited, Pune

7126926

IS 302 : Part 2 : Sec 8 (2024)

Household and Similar Electrical Appliances âSafety Part 2 Particular Requirements Section 8 Shavers, Hair Clippers and Similar Appliances (First Revision)

73000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking and instructions)	-	2000	-
8(Protection against access to live parts)	-	2000	-
10(Power input and current)	-	2000	-
11(Heating)	-	4000	-
12(Charging of metal-ion batteries)	-	15000	-
13.1 &13.2(Leakage current test)	-	1500	-
13.1 &13.3(Electric strength test)	-	1500	-
14(Transient overvoltages)	-	2000	-
15(Moisture resistance)	-	2000	-
15.3(Moisture resistance)	-	2000	-
16.1 &16.2(Leakage current test)	-	1500	-
16.1 & 16.3(Electric strength test)	-	1500	-
17(Overload protection of transformers and associated circuits)	-	4000	-
19.1 to 19.13, Table No. - 9(Abnormal operation)	-	5000	Charges applicable excluding the test of Cl.19.11.4.1 to Cl.19.11.4.7. The testing charges for EMI/EMC Testing (Cl.19.11.4.1 to Cl.19.11.4.7) will be charged extra.
19.101(Abnormal operation)	-	0	Testing charges included in Cl.19.1 TO cL.19.13
20.1(Stability and mechanical hazards)	-	1000	-
20.2(Stability and mechanical hazards)	-	1000	-
21(Mechanical strength)	-	3000	-
21.101(Mechanical strength)	-	0	Testing charges included in Cl.21
21.102(Mechanical strength)	-	0	Testing charges included in Cl.21
21.103(Mechanical strength)	-	0	Testing charges included in Cl.21
22(Construction)	-	5000	-
22.101(Construction)	-	0	Testing charges included in Cl.22
22.102(Construction)	-	0	Testing charges included in Cl.22
22.103(Construction)	-	0	Testing charges included in Cl.22
23(Internal wiring)	-	2000	-
24(Components)	-	3000	-
25("Supply connection and external flexible cords")	-	1000	-
26("Terminals for external conductors")	-	1000	-
27(Provision for earthing)	-	2000	-
28(Screws and connections)	-	1000	-
29("Clearances, creepage distances and solid insulation")	-	2000	-
30(Resistance to heat and fire)	-	3000	-
31(Resistance to rusting)	-	1000	-
32("Radiation, toxicity and similar hazards")	-	1000	-

20 Jun, 2028

-
Included w.e.f 25.03.2025 Exclusion : Cl 24 (Components), Cl 32 ("Radiation, toxicity and similar hazards")

6971

DELHI TEST HOUSE, Azadhpur

8131406

IS 736 (1986)

Specification for wrought aluminium and aluminium alloy plate for general engineering purposes (Third Revision)

ALL

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Freedom from defect)	-	500	-
5(chemical composition)	-	4500	-
6.1 table 2(0.2% proof strength)	-	1700	-
6.1 table 2(tensile strength)	-	1700	-
6.1 table 2(Elongation)	-	1700	-
8(Dimensions & Tolerances)	-	2000	-
5.1, Table 1(Aluminium)	-	500	-
5.1, Table 1(Copper)	-	500	-
5.1, Table 1(Magnesium)	-	500	-
5.1, Table 1(Silicon)	-	500	-
5.1, Table 1(Iron)	-	500	-
5.1, Table 1(Mangnese)	-	500	-
5.1, Table 1(Zinc)	-	500	-
5.1, Table 1(Titanium and /or other grain refining element)	-	500	-
5.1, Table 1(Chromium)	-	500	-
5.1, Table 1(Vanadium)	-	500	-

17 Jun, 2027

-
Included w.e.f. 03.03.2025

6972

IDMA LABORATORIES LIMITED, PANCHKULA

9123236

IS 5405 (2025)

Disposable Sanitary Napkin/Panty Liner/Maternity Pad/Period Panty - Specification ( Third Revision )

Sanitary Napkin, Panty liner, Maternity Pad, Period panty

261600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Cover/Top sheet)	-	800	Testing charges are Rs. 800/- for Cl. no. 3.1 Cover / Top sheet, 3.2 Absorbent core & 3.3 Barrier or Bottom sheet.
3.2(Absorbent core)	-	0	Testing charges already mentioned above at cl. no. 3.1 Cover / Top sheet i.e. Rs. 800/-.
3.3(Barrier or bottom sheet)	-	0	Testing charges already mentioned above at cl. no. 3.1 Cover / Top sheet i.e. Rs. 800/-.
4.1(Types)	-	800	Testing charges are 800/- for cl. 4.1 & 4.2
4.2(shapes)	-	0	Testing charges are 800/- for cl. 4.1 & 4.2 already mentioned above.
5(Sizes)	-	800	Testing charges are 800/- for Size, Size class, Length (Absorbent core only, Width (Absorbent core only as per cl. 5 Table - 1.
Cl. 5 Table-1(Type)	-	0	Total testing charges are Rs. 2,61,600/- including Bio compatibility evaluation - Cytotoxicity, Irritation & Skin sensitization (as per cl. no. 7.4) & (excluding Compostability as per cl. 7.6).
Cl. 5 Table-1(Size class)	-	0	Testing charges are 800/- for Size, Size class, Length (Absorbent core only, Width (Absorbent core only as per cl. 5 Table - 1 already mentioned above.
Cl. 5 Table-1(Length (Absorbent core only))	-	0	Testing charges are 800/- for Size, Size class, Length (Absorbent core only, Width (Absorbent core only as per cl. 5 Table - 1 already mentioned above.
Cl. 5 Table-1(Width (Absorbent core only))	-	0	Testing charges are 800/- for Size, Size class, Length (Absorbent core only, Width (Absorbent core only as per cl. 5 Table - 1 already mentioned above.
6.1(Manufacture, workmanship and finish)	-	500	Testing charges are 500/- for cl. 6.1 & 6.2.
6.2(Manufacture, workmanship and finish)	-	0	Testing charges are 500/- for cl. 6.1 & 6.2 already mentioned above.
7.1(pH Test)	-	1000	Testing charges are Rs. 21,600/- excluding Bio compatibility evaluation - Cytotoxicity, Irritation & Skin sensitization (as per cl. no. 7.4) &excluding Compostability as per cl. 7.6).
7.2("Ability to Withstand Pressure after Absorption: Liquid Absorption ml, Min")	-	1200	Testing charges are 1200/- for cl. Ability to Withstand Pressure after Absorption & Ability to Withstand Pressure after Absorption - leakage.
7.3.1(Bacterial and Fungal Bioburden)	-	3000	-
7.3.2(Staphylococcus aureus)	-	3000	-
7.4(Biocompatibility evaluation - Cytotoxicity (IS/ISO 10993 P-5))	-	50000	-
7.4(Biocompatibility evaluation - Irritation (IS 17932 P-7))	-	70000	-
7.4(Biocompatibility evaluation - skin Sensitization (Optional) (IS 17932 P-6))	-	120000	-
Cl 7.5(Phthalate test- Combination)	-	8000	-
7.7(Anti bacterial activity value (Optional) (IS/ISO 20743))	-	2500	-
7.6(Compostability (Optional) (IS/ISO 17088))	-	0	Clause no. 7.6 Compostability (Optional) test is applied for Exclusion as the test facilities are currently not available.

31 Dec, 2026

-
Included w.e.f.05.03.2025 Exclusion Cl 7.6 (Compostability (Optional) (IS/ISO 17088)

6973

IDMA LABORATORIES LIMITED, PANCHKULA

9123236

IS 15219 (2024)

Aluminium phosphide powder formulation - Specification (first revision)

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2.1(Description - IS 15219:2002)	-	1000		-
3.3.1(Aluminium Phosphide Content - IS 6438:1980)	-	6000		-

31 Dec, 2026

-
Included w.e.f.24.04.2025

6974

IDMA LABORATORIES LIMITED, PANCHKULA

9123236

IS 9356 (2024)

Butachlor emulsifiable concentrate (EC) - Specification (first revision)

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2.1(Description - IS 9356 : 2024)	-	500	-
3.2.2(Cold Test - IS 6940 : 1982)	-	1000	-
3.2.3(Flash Point - IS 6940 : 1982)	-	1000	-
3.2.4(Emulsion Test - IS 6940 : 1982)	-	1500	-
3.3.1(Butachlor Content - IS 9355 : 2024)	-	3000	-
3.3.2(Acidity (as H2SO4) - IS 6940 : 1982)	-	1500	-
3.3.2(Alkalinity (as NaOH) - IS 6940 : 1982)	-	0	Testing charges i.e. Rs. 1500/- already mentioned above at clause no. 3.3.2 (Acidity (as H2SO4).

31 Dec, 2026

-
Included w.e.f 09.04.2025

6975

IDMA LABORATORIES LIMITED, PANCHKULA

9123236

IS 9355 (2024)

Butachlor, Technical - Specification (First Revision)

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Description - IS 9355 : 2024)	-	500	-
3.2 & 7, Table - 1 (i)(Butachlor Content - IS 9355 : 2024)	-	3000	-
3.2 & 7, Table - 1 (ii)(Moisture Content - IS 6940 : 1982)	-	2000	-
3.2 & 7, Table - 1 (iii)(Acidity (as H2SO4) - IS 6940 : 1982)	-	1500	-
3.2 & 7, Table - 1 (iv)(Material insoluble in Acetone - IS 6940 : 1982)	-	1500	-

31 Dec, 2026

-
Included w.e.f 09.04.2025

6976

IDMA LABORATORIES LIMITED, PANCHKULA

9123236

IS 8074 (2024)

Monocrotophos, Soluble Concentrate (SL) - Specification (Third Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2.1(Description - IS 8074 : 2024)	-	500	-
3.2.2(Cold Test - IS 6940 : 1982)	-	1000	-
3.2.3(Flash Point - IS 6940 : 1982)	-	1000	-
3.3.1(Monocrotophos Content - IS 8025 : 2024)	-	3500	-
3.3.2(Free Aceto - Acetic Acid Monomethyl - Amide (MMA) content - IS 8025 : 2024)	-	3000	-
3.3.3(Acidity ( as H2SO4) - IS 6940 : 1982)	-	1000	-

31 Dec, 2026

-
Included w.e.f. 24.04.2025

6977

IDMA LABORATORIES LIMITED, PANCHKULA

9123236

IS 8025 (2024)

Monocrotophos, Technical - Specification (Third Revision)

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Description - IS 8025 : 2024)	-	1000	-
3.2 & 7 Table - 1 (i)(Monocrotophos Content - IS 8025 : 2024)	-	3500	-
3.2 & 7 Table - 1 (ii)(Free Acetic Acid Mono - methylamide (MMA) - IS 8025 : 2024)	-	3000	-
3.2 & 7 Table - 1 (iii)(Acidity (as H2SO4) - IS 6940 : 1982)	-	1500	-

31 Dec, 2026

-
Included w.e.f.24.04.2025

6978

VARDAN ENVIROLAB, GURUGRAM

8169616

IS 3735 (1996)

Canvas Shoes, Rubber Sole

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4.5 Consolidation Test IS 3400 (Part 5) : 1986 (From the quarter, cut a strip of 25.0 ± 0.5 mm width along the leagth of the boot and of sufficient length to permit separation over a length of 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100± 10mm per minute in accordance with IS 3400 (Part 5): 1986 or Static Dead Load Method as given in Annex C. The individual adhesion value for consolidation test shall not be less than 30N (3.0 kgf) for each of the teat piecea (see Note under 4.4).')	-	550	-
4.1.1 Upper, Sl No. (i) of Table 1(The upper shall consist of over layer of cotton, manmade or blended conforming' to the requirements given in Sl No. (i) of Table 1 as an overlayer and cotton drill conforming to the requirements given in Sl No. (ii) of Table 1, as an inner layer or lining. The two fabrics shall be firmly adhered together with rubber compound. )	-	550	-
Cl.4.1.1.1 Colour fastness(The dyed fabrics prescribed in 4.1.1 shall be fast todaylight and mechanical washing. Fastness to daylight shall be of rating 4 or better, when tested in accordance with IS 686 : 1985 or IS 2454: 1985. However in case of dispute the method prescribed in IS 686 : 1985 shall be considered as referee method.)	-	1500	-
Cl.4.1.2 Binding Material(IS 1954 : 1990) (IS1969 : 1985)(Cotton tape NEWAR used as binding material shall conform to the requirements prescribed in col 3 of Table 2, when tested in accordance with the methods referred to in col 4 of the table.)	-	200	-
Cl.4.1.2.1 Anmex B.(Cotton, manmade or blended shall be used as binding material.' 'Coloured cotton tapes shall have fastness to day light of rating as and if agreed to between the purchaser and the supplier when tested in accordance with IS 686 : 1985. The black tapes shall be free from sulphur dyes when tested in accordance with Annex B.')	-	1500	-
Cl.4.1.3.1( Sewing thread cotton, manmade or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other suitable thread shall have breaking load not less than above referred requirement of specification. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other suitable thread shall have breaking load not less than above referred requirement of specification.')	-	550	-
Cl.4.1.3.2 (IS 2454 : 1985) IS 765 : 1979 IS 971 : 1966( The colour of the threads shall be as agreedto between the purchaser and the supplier. The dyed threads shall conform to the following requirements or IS 686 : 1985'.)	-	1000	-
Cl.4.1.4(.Brass, steel or aluminium eyelets of 7.5 mm diameter and wall thickness 0.30 to 0.35 mm shall be used.')	-	300	-
Cl.4.1.5 Laces( The shoes shall be provided with fabric braided laces either matching the shade of the upper or black or The length of the lace shall be 60 ± 3 cm )	-	200	-
Cl.4.1.5 Laces(and shallhave the breaking strength of not less than 250 N when tested between 18 cm grips in accordance with IS 1969 : 1985, the rate of traverse of power actuated grip being 300 mm/min.)	-	550	-
Cl.4.1.5 Laces Annex B(In case the laces are black, the same shall pass the test for freedom from sulpher dyes when tested in accordance with Annex B. The two ends of the lace shall be provided with suitable metal or plastic tips.)	-	550	-
Cl.4.1.6 Rubber Components(The rubber components shall conform to the requirements given in Table 4, when tested from finished boots.However in case it is not possible to cut the test pieces from the made up boots then 4.1.5.3 of IS 13695 : 1993 shall be followed.')	-	350	-
Cl.4.1.6.2 Ageing col 4 of Table 5.(The shoes shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the shoes shall conform to the physical requirements prescribed in col 4 of Table 5. )	-	550	-
Cl.4.1.6.2 Ageing (None of the rubber components of the shoes shall show any sign of tackiness or crack developed after ageing, when examined visually)	-	550	-
Cl.4.1.6.3 Thickness of components in Table 6.(Individual components of the shoes shall comply with the thickness and material requirements prescribed in Table 6.)	-	300	-
CL.4.2 Shape and Design IS 1638 : 1969(Cl 4.2.1 The shoes shall be made according to design and pattern as agreed to between the purchaser and the supplier. Size and fittings of the shoes shall be in accordance with IS 1638 : 1969 unless otherwise specified by the purchaser.)	-	300	-
Cl.4.2.2( The recommended design of canvas shoes is shown in Fig. 1.)	-	300	-
Cl.4.3 Construction Cl 4.3.1( The upper shall be stitched on a lock stitch machine and the number of stitches shall be 30 to 40 per dm.)	-	500	-
Cl.'4.3.2( Back of the upper shall be reinforced with a strip of upper material when there is a seam.')	-	550	-
Cl.4.3.3( The counter shall be stitched at the back, set from bottom of lining and bound flat on top edge with white/scoured binding material cut in bias and formed as a tape. T )	-	250	-
Cl.4.3.3(he number of stitches shall be 30 to 40 per decimetre. The counter binding shall meet the binding of the upper at the centre top edge of the heel.)	-	250	-
Cl.4.3.3(The edges of quarter shall be bound with dyed cotton binding material or matching to the colour of the upper, cut in bias and formed as a tape.)	-	250	-
Cl.4.3.4 (The vantp shall be strengthened with a rubber toe-cap (see Fig. 1).)	-	250	-
Cl.4.3.5( Five pairs of eyelets shall be fitted in each shoe. The eyelets shall be properly clenched without any distortion. It shall properly match the colour of the upper canvas, or as agreed to between the purchaser and the supplier.)	-	250	-
Cl.4.3.6( The shoes shall be free from folds, wrinkles in the upper, blisters, embedded foreign matters and excessive surface markings. In appearance, general workmanship, finish and all other respects, not defined in the standard, the shoes shall be similar to the sample approved by the purchaser, if any)	-	250	-
CL.4.3.7( The soles shall be of even substance and ofone layer only.)	-	250	-
Cl.4.3.8( A rubber foxing shall be fixed all round the sole and heel. The colour shall be as agreed to between the purchaser and the supplier. )	-	250	-
Cl.4.3.8(The foxing, not less than 18 mm wide, shall not extend beyond the edges of the sole at the bottom)	-	250	-
Cl.4.4 Adhesion Test(From the upper-foxing portion where it is adhered to the canvas, parallel to the waist of sole, cut a strip of length 100 mm and width 8 mm. Separate out the plies initially by breaking the bond to a length of about 75 mm. Carry out the test on two specimens in accordance with IS 3400 (Part 5) : 1986. There shall be no further separation within 1 minute at a load of 1 kg for each of the two specimens.)	-	550	-
CL.4.6 Mass(The mass of one pair of finished shoes of size 8 shall not exceed 750 g with an increase or decrease of 25 g for each bigger or smaller size respectively)	-	200	-
Cl.4.5 Consolidation Test IS 3400 (Part 5) : 1986 (From the quarter, cut a strip of 25.0 ± 0.5 mm width along the leagth of the boot and of sufficient length to permit separation over a length of 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100± 10mm per minute in accordance with IS 3400 (Part 5): 1986 or Static Dead Load Method as given in Annex C. The individual adhesion value for consolidation test shall not be less than 30N (3.0 kgf) for each of the teat piecea (see Note under 4.4).')	-	0	Parameter Repeat
4.1.1 Upper, Sl No. (i) of Table 1(The upper shall consist of over layer of cotton, manmade or blended conforming' to the requirements given in Sl No. (i) of Table 1 as an overlayer and cotton drill conforming to the requirements given in Sl No. (ii) of Table 1, as an inner layer or lining. The two fabrics shall be firmly adhered together with rubber compound. )	-	0	Parameter Repeat
Cl.4.1.1.1 Colour fastness(The dyed fabrics prescribed in 4.1.1 shall be fast todaylight and mechanical washing. Fastness to daylight shall be of rating 4 or better, when tested in accordance with IS 686 : 1985 or IS 2454: 1985. However in case of dispute the method prescribed in IS 686 : 1985 shall be considered as referee method.)	-	0	Parameter Repeat
Cl.4.1.2 Binding Material(IS 1954 : 1990) (IS1969 : 1985)(Cotton tape NEWAR used as binding material shall conform to the requirements prescribed in col 3 of Table 2, when tested in accordance with the methods referred to in col 4 of the table.)	-	0	Parameter Repeat
Cl.4.1.2.1 Anmex B.(Cotton, manmade or blended shall be used as binding material.' 'Coloured cotton tapes shall have fastness to day light of rating as and if agreed to between the purchaser and the supplier when tested in accordance with IS 686 : 1985. The black tapes shall be free from sulphur dyes when tested in accordance with Annex B.')	-	0	Parameter Repeat
Cl.4.1.3.1( Sewing thread cotton, manmade or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other suitable thread shall have breaking load not less than above referred requirement of specification. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other suitable thread shall have breaking load not less than above referred requirement of specification.')	-	0	Parameter Repeat
Cl.4.1.3.2 (IS 2454 : 1985) IS 765 : 1979 IS 971 : 1966( The colour of the threads shall be as agreedto between the purchaser and the supplier. The dyed threads shall conform to the following requirements or IS 686 : 1985'.)	-	0	Parameter Repeat
Cl.4.1.4(.Brass, steel or aluminium eyelets of 7.5 mm diameter and wall thickness 0.30 to 0.35 mm shall be used.')	-	0	Parameter Repeat
Cl.4.1.5 Laces( The shoes shall be provided with fabric braided laces either matching the shade of the upper or black or The length of the lace shall be 60 ± 3 cm )	-	0	Parameter Repeat
Cl.4.1.5 Laces(and shallhave the breaking strength of not less than 250 N when tested between 18 cm grips in accordance with IS 1969 : 1985, the rate of traverse of power actuated grip being 300 mm/min.)	-	0	Parameter Repeat
Cl.4.1.5 Laces Annex B(In case the laces are black, the same shall pass the test for freedom from sulpher dyes when tested in accordance with Annex B. The two ends of the lace shall be provided with suitable metal or plastic tips.)	-	0	Parameter Repeat
Cl.4.1.6 Rubber Components(The rubber components shall conform to the requirements given in Table 4, when tested from finished boots.However in case it is not possible to cut the test pieces from the made up boots then 4.1.5.3 of IS 13695 : 1993 shall be followed.')	-	0	Parameter Repeat
Cl.4.1.6.2 Ageing col 4 of Table 5.(The shoes shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the shoes shall conform to the physical requirements prescribed in col 4 of Table 5. )	-	0	Parameter Repeat
Cl.4.1.6.2 Ageing (None of the rubber components of the shoes shall show any sign of tackiness or crack developed after ageing, when examined visually)	-	0	Parameter Repeat
Cl.4.1.6.3 Thickness of components in Table 6.(Individual components of the shoes shall comply with the thickness and material requirements prescribed in Table 6.)	-	0	Parameter Repeat
CL.4.2 Shape and Design IS 1638 : 1969(Cl 4.2.1 The shoes shall be made according to design and pattern as agreed to between the purchaser and the supplier. Size and fittings of the shoes shall be in accordance with IS 1638 : 1969 unless otherwise specified by the purchaser.)	-	0	Parameter Repeat
Cl.4.2.2( The recommended design of canvas shoes is shown in Fig. 1.)	-	0	Parameter Repeat
Cl.4.3 Construction Cl 4.3.1( The upper shall be stitched on a lock stitch machine and the number of stitches shall be 30 to 40 per dm.)	-	0	Parameter Repeat
Cl.'4.3.2( Back of the upper shall be reinforced with a strip of upper material when there is a seam.')	-	0	Parameter Repeat
Cl.4.3.3( The counter shall be stitched at the back, set from bottom of lining and bound flat on top edge with white/scoured binding material cut in bias and formed as a tape. T )	-	0	Parameter Repeat
Cl.4.3.3(he number of stitches shall be 30 to 40 per decimetre. The counter binding shall meet the binding of the upper at the centre top edge of the heel.)	-	0	Parameter Repeat
Cl.4.3.3(The edges of quarter shall be bound with dyed cotton binding material or matching to the colour of the upper, cut in bias and formed as a tape.)	-	0	Parameter Repeat
Cl.4.3.4 (The vantp shall be strengthened with a rubber toe-cap (see Fig. 1).)	-	0	Parameter Repeat
Cl.4.3.5( Five pairs of eyelets shall be fitted in each shoe. The eyelets shall be properly clenched without any distortion. It shall properly match the colour of the upper canvas, or as agreed to between the purchaser and the supplier.)	-	0	Parameter Repeat
Cl.4.3.6( The shoes shall be free from folds, wrinkles in the upper, blisters, embedded foreign matters and excessive surface markings. In appearance, general workmanship, finish and all other respects, not defined in the standard, the shoes shall be similar to the sample approved by the purchaser, if any)	-	0	Parameter Repeat
CL.4.3.7( The soles shall be of even substance and ofone layer only.)	-	0	Parameter Repeat
Cl.4.3.8( A rubber foxing shall be fixed all round the sole and heel. The colour shall be as agreed to between the purchaser and the supplier. )	-	0	Parameter Repeat
Cl.4.3.8(The foxing, not less than 18 mm wide, shall not extend beyond the edges of the sole at the bottom)	-	0	Parameter Repeat
Cl.4.4 Adhesion Test(From the upper-foxing portion where it is adhered to the canvas, parallel to the waist of sole, cut a strip of length 100 mm and width 8 mm. Separate out the plies initially by breaking the bond to a length of about 75 mm. Carry out the test on two specimens in accordance with IS 3400 (Part 5) : 1986. There shall be no further separation within 1 minute at a load of 1 kg for each of the two specimens.)	-	0	Parameter Repeat
CL.4.6 Mass(The mass of one pair of finished shoes of size 8 shall not exceed 750 g with an increase or decrease of 25 g for each bigger or smaller size respectively)	-	0	Parameter Repeat
Cl.4.5 Consolidation Test IS 3400 (Part 5) : 1986 (From the quarter, cut a strip of 25.0 ± 0.5 mm width along the leagth of the boot and of sufficient length to permit separation over a length of 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100± 10mm per minute in accordance with IS 3400 (Part 5): 1986 or Static Dead Load Method as given in Annex C. The individual adhesion value for consolidation test shall not be less than 30N (3.0 kgf) for each of the teat piecea (see Note under 4.4).')	-	0	Parameter Repeat
4.1.1 Upper, Sl No. (i) of Table 1(The upper shall consist of over layer of cotton, manmade or blended conforming' to the requirements given in Sl No. (i) of Table 1 as an overlayer and cotton drill conforming to the requirements given in Sl No. (ii) of Table 1, as an inner layer or lining. The two fabrics shall be firmly adhered together with rubber compound. )	-	0	Parameter Repeat
Cl.4.1.1.1 Colour fastness(The dyed fabrics prescribed in 4.1.1 shall be fast todaylight and mechanical washing. Fastness to daylight shall be of rating 4 or better, when tested in accordance with IS 686 : 1985 or IS 2454: 1985. However in case of dispute the method prescribed in IS 686 : 1985 shall be considered as referee method.)	-	0	Parameter Repeat
Cl.4.1.2 Binding Material(IS 1954 : 1990) (IS1969 : 1985)(Cotton tape NEWAR used as binding material shall conform to the requirements prescribed in col 3 of Table 2, when tested in accordance with the methods referred to in col 4 of the table.)	-	0	Parameter Repeat
Cl.4.1.2.1 Anmex B.(Cotton, manmade or blended shall be used as binding material.' 'Coloured cotton tapes shall have fastness to day light of rating as and if agreed to between the purchaser and the supplier when tested in accordance with IS 686 : 1985. The black tapes shall be free from sulphur dyes when tested in accordance with Annex B.')	-	0	Parameter Repeat
Cl.4.1.3.1( Sewing thread cotton, manmade or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other suitable thread shall have breaking load not less than above referred requirement of specification. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other suitable thread shall have breaking load not less than above referred requirement of specification.')	-	0	Parameter Repeat
Cl.4.1.3.2 (IS 2454 : 1985) IS 765 : 1979 IS 971 : 1966( The colour of the threads shall be as agreedto between the purchaser and the supplier. The dyed threads shall conform to the following requirements or IS 686 : 1985'.)	-	0	Parameter Repeat
Cl.4.1.4(.Brass, steel or aluminium eyelets of 7.5 mm diameter and wall thickness 0.30 to 0.35 mm shall be used.')	-	0	Parameter Repeat
Cl.4.1.5 Laces( The shoes shall be provided with fabric braided laces either matching the shade of the upper or black or The length of the lace shall be 60 ± 3 cm )	-	0	Parameter Repeat
Cl.4.1.5 Laces(and shallhave the breaking strength of not less than 250 N when tested between 18 cm grips in accordance with IS 1969 : 1985, the rate of traverse of power actuated grip being 300 mm/min.)	-	0	Parameter Repeat
Cl.4.1.5 Laces Annex B(In case the laces are black, the same shall pass the test for freedom from sulpher dyes when tested in accordance with Annex B. The two ends of the lace shall be provided with suitable metal or plastic tips.)	-	0	Parameter Repeat
Cl.4.1.6 Rubber Components(The rubber components shall conform to the requirements given in Table 4, when tested from finished boots.However in case it is not possible to cut the test pieces from the made up boots then 4.1.5.3 of IS 13695 : 1993 shall be followed.')	-	0	Parameter Repeat
Cl.4.1.6.2 Ageing col 4 of Table 5.(The shoes shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the shoes shall conform to the physical requirements prescribed in col 4 of Table 5. )	-	0	Parameter Repeat
Cl.4.1.6.2 Ageing (None of the rubber components of the shoes shall show any sign of tackiness or crack developed after ageing, when examined visually)	-	0	Parameter Repeat
Cl.4.1.6.3 Thickness of components in Table 6.(Individual components of the shoes shall comply with the thickness and material requirements prescribed in Table 6.)	-	0	Parameter Repeat
CL.4.2 Shape and Design IS 1638 : 1969(Cl 4.2.1 The shoes shall be made according to design and pattern as agreed to between the purchaser and the supplier. Size and fittings of the shoes shall be in accordance with IS 1638 : 1969 unless otherwise specified by the purchaser.)	-	0	Parameter Repeat
Cl.4.2.2( The recommended design of canvas shoes is shown in Fig. 1.)	-	0	Parameter Repeat
Cl.4.3 Construction Cl 4.3.1( The upper shall be stitched on a lock stitch machine and the number of stitches shall be 30 to 40 per dm.)	-	0	Parameter Repeat
Cl.'4.3.2( Back of the upper shall be reinforced with a strip of upper material when there is a seam.')	-	0	Parameter Repeat
Cl.4.3.3( The counter shall be stitched at the back, set from bottom of lining and bound flat on top edge with white/scoured binding material cut in bias and formed as a tape. T )	-	0	Parameter Repeat
Cl.4.3.3(he number of stitches shall be 30 to 40 per decimetre. The counter binding shall meet the binding of the upper at the centre top edge of the heel.)	-	0	Parameter Repeat
Cl.4.3.3(The edges of quarter shall be bound with dyed cotton binding material or matching to the colour of the upper, cut in bias and formed as a tape.)	-	0	Parameter Repeat
Cl.4.3.4 (The vantp shall be strengthened with a rubber toe-cap (see Fig. 1).)	-	0	Parameter Repeat
Cl.4.3.5( Five pairs of eyelets shall be fitted in each shoe. The eyelets shall be properly clenched without any distortion. It shall properly match the colour of the upper canvas, or as agreed to between the purchaser and the supplier.)	-	0	Parameter Repeat
Cl.4.3.6( The shoes shall be free from folds, wrinkles in the upper, blisters, embedded foreign matters and excessive surface markings. In appearance, general workmanship, finish and all other respects, not defined in the standard, the shoes shall be similar to the sample approved by the purchaser, if any)	-	0	Parameter Repeat
CL.4.3.7( The soles shall be of even substance and ofone layer only.)	-	0	Parameter Repeat
Cl.4.3.8( A rubber foxing shall be fixed all round the sole and heel. The colour shall be as agreed to between the purchaser and the supplier. )	-	0	Parameter Repeat
Cl.4.3.8(The foxing, not less than 18 mm wide, shall not extend beyond the edges of the sole at the bottom)	-	0	Parameter Repeat
Cl.4.4 Adhesion Test(From the upper-foxing portion where it is adhered to the canvas, parallel to the waist of sole, cut a strip of length 100 mm and width 8 mm. Separate out the plies initially by breaking the bond to a length of about 75 mm. Carry out the test on two specimens in accordance with IS 3400 (Part 5) : 1986. There shall be no further separation within 1 minute at a load of 1 kg for each of the two specimens.)	-	0	Parameter Repeat
CL.4.6 Mass(The mass of one pair of finished shoes of size 8 shall not exceed 750 g with an increase or decrease of 25 g for each bigger or smaller size respectively)	-	0	Parameter Repeat
4.8(Adhesion )	-	550	-
4.7(Consolidation test )	-	550	-
4.6(Mass )	-	200	-
4.5(Finish )	-	550	-
4.4(Contruction )	-	300	-
4.3(Leg Height )	-	250	-
4.2(Design )	-	250	-
4.1.6.2(Thickness of components )	-	550	-
4.1.6.2(Ageing)	-	550	-
4.1.6.2(Elongation at break after ageing )	-	550	-
4.1.6.2(Tensile after ageing )	-	550	-
4.1.6(Compression set )	-	1000	-
4.1.6(Elongation at break )	-	550	-
4.1.6(Tensile strength)	-	550	-
4.1.6(Hardness (after accelerated ))	-	450	-
4.1.6(Flexing resistance test)	-	1200	-
4.1.6(Hardness )	-	450	-
4.1.6(Relative density)	-	350	-
4.1.5(Sulpher dyes content )	-	550	-
4.1.5(Breaking Load )	-	550	-
4.1.5(Length )	-	550	-
4.1.4(Thickness)	-	250	-
4.1.4(Size )	-	250	-
4.1.3(Color fastness to perspiration)	-	450	-
4.1.3(Colorfastness to washing)	-	1000	-
4.1.3(Colorfastness to light )	-	1500	-
4.1.3(Single thread breaking load)	-	550	-
4.1.3(Construction )	-	250	-
4.1.2(Colorfastness to light )	-	1500	-
4.1.2(Colorfastness to washing)	-	1000	-
4.1.2(Breaking Strength )	-	550	-
4.1.2(Width )	-	250	-
4.1.1.2(Colorfastness to washing)	-	1000	-
4.1.1.1(Colorfastness to light )	-	1500	-
4.1.1 (Drill) (End & Picks/dm)	-	250	-
4.1.1 (Drill) (Colorfastness to light )	-	1500	-
4.1.1 (canvas )(End & Picks/dm)	-	250	-
4.1.1 (canvas )(Breaking Load )	-	550	-
5, 5.1, Cl. 5.2, Cl. 5.2.1, Cl. 5.2.1.1(Packing and marking)	-	550	-
" CL. 5.1, Cl. 5.2, Cl. 5.2.1, Cl. 5.2.1.1(Packing and marking ")	-	550	-

26 Dec, 2027

-
Included .w.e.f.17.06.2025

6979

IDMA LABORATORIES LIMITED, PANCHKULA

9123236

IS 3205 (2024)

Precipitated Barium Carbonate, Technical - Specification (Second Revision)

Grade 1 & Grade 2

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Description - IS 3205:2024)	-	500	-
4.2 Table(i)(Barium (as Ba) - IS 3205: 2024)	-	1500	-
4.2 Table(ii)(Carbonate (as CO3) - IS 3205: 2024)	-	2000	-
4.2 Table(iii)(Moisture - IS 3205: 2024)	-	2000	-
4.2 Table(iv)(Matter insoluble in hydrochloric acid - IS 3205: 2024)	-	1500	-
4.2 Table(v)(Free alkali - IS 3205: 2024)	-	1500	-
4.2 Table(vi)(Water soluble sulphide (as BaS) - IS 3205: 2024)	-	1500	-
4.2 Table(vii)(Total sulphur (as SO4) - IS 3205: 2024)	-	1500	-
4.2 Table(viii)(Alkali and other metal sulphates (as BaSO4) - IS 3205: 2024)	-	1500	-
4.2 Table(ix)(Sodium oxides (as Na2O)- IS 3205: 2024)	-	1500	-
4.2 Table(x)(Iron (as Fe2O3)- IS 3205: 2024)	-	1500	-
4.2 Table(xi)(Tap density- IS 3205: 2024)	-	1000	-
4.2 Table(xii)(Residue retained on 63 micron IS sieve- IS 3205: 2024)	-	1500	-
4.2 Tablexii(i)(Reaction efficiency (after 45 min)- IS 3205: 2024)	-	1000	-

31 Dec, 2026

-
Included w.e.f.24.04.2025

6980

CSIR-Central Building Research Institute, Roorkee

9184204

IS 16945 (2018)

Fire resistance test for glass walls

450000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
11(Integrity, Insulation, Radiation)	-	450000		450000 plus GST for two hours

12 Mar, 2028

-
-

6981

CSIR-Central Building Research Institute, Roorkee

9184204

IS 16947 (2018)

Fire resistance tests for doors with glass panes, openable glass windows and sliding glass doors

450000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
9(Integrity, Insulation, Radiation)	-	450000		450000 plus GST for two hours

12 Mar, 2028

-
-

6982

Alpha Test House Services LLP (160), Sahibzada Ajit Singh Nagar

9138706

IS 18480 : Part 1 (2023)

Cross Recessed Tapping Screws: Part 1 Pan Head

Cross Recessed Tapping Screws

21000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause. 3.0(Dimenssions.)	-	21000	-
Clause. 3.0(Thread size.)	-	21000	-
Clause. 3.0(Length)	-	21000	-
Clause. 4.0(Material)	-	21000	-
Clause. 4.0(Thread)	-	21000	-
Clause. 4.0(Cross Recess)	-	21000	-
Clause. 4.0(Tolerances)	-	21000	-
Clause. 4.0(Mechnical and functional properties.)	-	21000	-
Clause. 4.0(Finish)	-	21000	-
Clause. 4.0(Acceptability)	-	21000	-
Clause.5.0(Designation)	-	21000	-
Clause.5.0(Marking)	-	21000	-

31 Dec, 2029

-
-

6983

DELHI TEST HOUSE, Azadhpur

8131406

IS 740 (1977)

Specification for wrought aluminium and aluminium alloy rivet stock for general engineering purposes (Second Revision)

ALL

9500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1, Table 1of IS:740 (Designation & Condition 65032, 'W')(Tensile Strength of Size upto and including 25 mm)	-	2000	NA
4.1, Table 1of IS:740 (Designation & Condition 64430, 'W')(Tensile Strength of Size upto and including 25 mm)	-	2000	NA
4.1, Table 1of IS:740 (Designation & Condition 55000, 'OD')(Tensile Strength of Size upto and including 25 mm)	-	2000	NA
4.1, Table 1of IS:740 (Designation & Condition 55000, 'O or M')(Tensile Strength of Size upto and including 25 mm)	-	2000	NA
4.1, Table 1of IS:740 (Designation & Condition 53000, 'OD')(Tensile Strength of Size upto and including 25 mm)	-	2000	NA
4.1, Table 1of IS:740 (Designation & Condition 53000, 'O or M')(Tensile Strength of Size upto and including 25 mm)	-	2000	NA
4.1, Table 1of IS:740 (Designation & Condition 24345, 'W')(Tensile Strength of Size upto and including 12 mm)	-	2000	NA
4.1, Table 1of IS:740 (Designation & Condition 19000, '112')(Tensile Strength of Size upto and including 12 mm)	-	2000	NA
4.1, Table 1of IS:740 (Designation 65032)(Aluminium)	-	500	NA
4.1, Table 1of IS:740 (Designation 65032)(Either Cr or Mn shall present)	-	500	NA
4.1, Table 1of IS:740 (Designation 65032)(Chromium)	-	500	NA
4.1, Table 1of IS:740 (Designation 65032)(Titanium and or other grain refining elements)	-	500	NA
4.1, Table 1of IS:740 (Designation 65032)(Zinc)	-	500	NA
4.1, Table 1of IS:740 (Designation 65032)(Manganese)	-	500	NA
4.1, Table 1of IS:740 (Designation 65032)(Iron)	-	500	NA
4.1, Table 1of IS:740 (Designation 65032)(Silicon)	-	500	NA
4.1, Table 1of IS:740 (Designation 65032)(Magnesium)	-	500	NA
4.1, Table 1of IS:740 (Designation 65032)(Copper)	-	500	NA
4.1, Table 1of IS:740 (Designation 64430)(Aluminium)	-	500	NA
4.1, Table 1of IS:740 (Designation 64430)(Cr+Mn)	-	500	NA
4.1, Table 1of IS:740 (Designation 64430)(Chromium)	-	500	NA
4.1, Table 1of IS:740 (Designation 64430)(Titanium and or other grain refining elements)	-	500	NA
4.1, Table 1of IS:740 (Designation 64430)(Zinc)	-	500	NA
4.1, Table 1of IS:740 (Designation 64430)(Manganese)	-	500	NA
4.1, Table 1of IS:740 (Designation 64430)(Iron)	-	500	NA
4.1, Table 1of IS:740 (Designation 64430)(Silicon)	-	500	NA
4.1, Table 1of IS:740 (Designation 64430)(Magnesium)	-	500	NA
4.1, Table 1of IS:740 (Designation 64430)(Copper)	-	500	NA
4.1, Table 1of IS:740 (Designation 55000)(Aluminium)	-	500	NA
4.1, Table 1of IS:740 (Designation 55000)(Cr+Mn)	-	2000	NA
4.1, Table 1of IS:740 (Designation 55000)(Chromium)	-	500	NA
4.1, Table 1of IS:740 (Designation 55000)(Titanium and or other grain refining elements)	-	500	NA
4.1, Table 1of IS:740 (Designation 55000)(Zinc)	-	500	NA
4.1, Table 1of IS:740 (Designation 55000)(Manganese)	-	500	NA
4.1, Table 1of IS:740 (Designation 55000)(Iron)	-	500	NA
4.1, Table 1of IS:740 (Designation 55000)(Silicon)	-	500	NA
4.1, Table 1of IS:740 (Designation 55000)(Magnesium)	-	500	NA
4.1, Table 1of IS:740 (Designation 55000)(Copper)	-	500	NA
4.1, Table 1of IS:740 (Designation 53000)(Aluminium)	-	500	NA
4.1, Table 1of IS:740 (Designation 53000)(Cr+Mn)	-	2000	NA
4.1, Table 1of IS:740 (Designation 53000)(Chromium)	-	500	NA
4.1, Table 1of IS:740 (Designation 53000)(Titanium and or other grain refining elements)	-	500	NA
4.1, Table 1of IS:740 (Designation 53000)(Zinc)	-	500	NA
4.1, Table 1of IS:740 (Designation 53000)(Manganese)	-	500	NA
4.1, Table 1of IS:740 (Designation 53000)(Iron)	-	500	NA
4.1, Table 1of IS:740 (Designation 53000)(Silicon)	-	500	NA
4.1, Table 1of IS:740 (Designation 53000)(Magnesium)	-	500	NA
4.1, Table 1of IS:740 (Designation 53000)(Copper)	-	500	NA
4.1, Table 1of IS:740 (Designation 24345)(Aluminium)	-	500	NA
4.1, Table 1of IS:740 (Designation 24345)(Chromium)	-	500	NA
4.1, Table 1of IS:740 (Designation 24345)(Titanium and or other grain refining elements)	-	500	NA
4.1, Table 1of IS:740 (Designation 24345)(Zinc)	-	500	NA
4.1, Table 1of IS:740 (Designation 24345)(Manganese)	-	500	NA
4.1, Table 1of IS:740 (Designation 24345)(Iron)	-	500	NA
4.1, Table 1of IS:740 (Designation 24345)(Silicon)	-	500	NA
4.1, Table 1of IS:740 (Designation 24345)(Magnesium)	-	500	NA
4.1, Table 1of IS:740 (Designation 24345)(Copper)	-	500	NA
4.1, Table 1of IS:740 (Designation 19000)(Cu+Mg+Si+Fe+Mn+Zn)	-	2000	NA
4.1, Table 1of IS:740 (Designation 19000)(Aluminium)	-	500	NA
4.1, Table 1of IS:740 (Designation 19000)(Zinc)	-	500	NA
4.1, Table 1of IS:740 (Designation 19000)(Manganese)	-	500	NA
4.1, Table 1of IS:740 (Designation 19000)(Iron)	-	500	NA
4.1, Table 1of IS:740 (Designation 19000)(Silicon)	-	500	NA
4.1, Table 1of IS:740 (Designation 19000)(Magnesium)	-	500	NA
4.1, Table 1of IS:740 (Designation 19000)(Copper)	-	500	NA
6(Freedom From Defects)	-	500	NA
7(Dmension And Tolerances)	-	2000	NA
9.2(Head Forming Test)	-	1500	NA
11(Marking)	-	250	NA

17 Jun, 2027

-
Included w.e.f. 03.03.2025

6984

DELHI TEST HOUSE, Azadhpur

8131406

IS 734 (1975)

Specification for wrought aluminium and aluminium alloy forging stock and forgings (For General Engineering Purposes) (Second Revision)

ALL

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1 table 2(0.2% proof strength)	-	2000	COMPLETE TESTING - 10000
5.1 table 2(Tensile strength)	-	2000	COMPLETE TESTING - 10000
5.1 table 2(Elongation)	-	1000	COMPLETE TESTING - 10000
Cl.5.1(Aluminium - IS 504 and its parts or any other intrumental/chemical methods)	-	500	COMPLETE TESTING - 10000
Cl.5.1(Copper - IS 504 and its parts or any other intrumental/chemical methods)	-	500	COMPLETE TESTING - 10000
Cl.5.1(Magnesium - IS 504 and its parts or any other intrumental/chemical methods)	-	500	COMPLETE TESTING - 10000
Cl.5.1(Silicon - IS 504 and its parts or any other intrumental/chemical methods)	-	500	COMPLETE TESTING - 10000
Cl.5.1(Iron - IS 504 and its parts or any other intrumental/chemical methods)	-	500	COMPLETE TESTING - 10000
Cl.5.1(Manganese - IS 504 and its parts or any other intrumental/chemical methods)	-	500	COMPLETE TESTING - 10000
Cl.5.1(Zinc - IS 504 and its parts or any other intrumental/chemical methods)	-	500	COMPLETE TESTING - 10000
Cl.5.1(Titanium And/or Other Grain Refining Elements - IS 504 and its parts or any other intrumental/chemical methods)	-	500	COMPLETE TESTING - 10000
Cl.5.1(Chromium - IS 504 and its parts or any other intrumental/chemical methods)	-	500	COMPLETE TESTING - 10000
Cl.5.1(Remarks (Cu + Mg + Si + Fe + Mn + Zn) - IS 504 and its parts or any other intrumental/chemical methods)	-	3000	COMPLETE TESTING - 10000
4.1(Freedom from defects)	-	250	COMPLETE TESTING - 10000
9.1(Tensile test)	-	2000	COMPLETE TESTING - 10000
5.1 table 1(chemical composition)	-	5000	COMPLETE TESTING - 10000

17 Jun, 2027

-
Included w.e.f. 03.03.2025

6985

ADS LABTECH, GHAZIABAD

8178326

IS 1489 (Part 1) (2015)

Portland pozzolana cement - Specification: Part 1 fly Ash Based

PPC

8250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7 -Table 2- vi(Drying Shrinkage- IS 4031 Part 10)	-	1500	OK
7 -Table 2- iv- c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	500	OK
7 -Table 2- iv- b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	500	OK
7 -Table 2- iv- a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	500	OK
7 -Table 2-iii- b(Setting Time Final- 4031 Part 5)	-	500	OK
7 -Table 2- iii- a(Setting Time Initial- 4031 Part 5)	-	500	OK
7 -Table 2- ii- b(Expansion after aeration- 4031 Part 3)	-	500	OK
7 -Table 2- ii- b(Expansion by Autoclave- 4031 Part 3)	-	500	OK
7 -Table 2- ii- a(Expansion after aeration - 4031 Part 3)	-	500	OK
7 -Table 2- ii- a(Expansion by Le Chatelier- 4031 Part 3)	-	500	OK
7 -Table 2- i(Fineness 4031 Part 2)	-	1000	OK
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	500	OK
6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985)	-	500	OK
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	500	OK
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	500	OK
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	500	OK
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	500	OK
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	500	OK
6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985)	-	500	OK
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	500	OK
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	500	OK
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	500	OK
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	500	OK
7 -Table 2- vi(Drying Shrinkage- IS 4031 Part 10)	-	1500	OK
7 -Table 2- iv- c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	500	OK
7 -Table 2- iv- b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	500	OK
7 -Table 2- iv- a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	500	OK
7 -Table 2-iii- b(Setting Time Final- 4031 Part 5)	-	500	OK
7 -Table 2- iii- a(Setting Time Initial- 4031 Part 5)	-	500	OK
7 -Table 2- ii- b(Expansion after aeration- 4031 Part 3)	-	500	OK
7 -Table 2- ii- b(Expansion by Autoclave- 4031 Part 3)	-	500	OK
7 -Table 2- ii- a(Expansion after aeration - 4031 Part 3)	-	500	OK
7 -Table 2- ii- a(Expansion by Le Chatelier- 4031 Part 3)	-	500	OK
7 -Table 2- i(Fineness 4031 Part 2)	-	1000	OK
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	500	OK
6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985)	-	500	OK
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	500	OK
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	500	OK
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	500	OK
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	500	OK
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	500	OK
6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985)	-	500	OK
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	500	OK
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	500	OK
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	500	OK
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	500	OK
Clause 7 Table 2 SI No. (v) (Compressive strength of Transverse Specimen, 672 ± 4 h)	-	1000	OK
Clause 7 Table 2 SI No. (v) (Compressive strength of Transverse Specimen, 168 ± 2 h)	-	1000	OK
Clause 7 Table 2 SI No. (v) (Compressive strength of Transverse Specimen, 72 ± 1 h)	-	1000	OK
4(RAW MATERIAL)	-	500	OK
7 -Table 2- v(Transverse Strength - IS 4031 Part 8 (Optional))	-	1000	OK
7 -Table 2- v(Transverse Strength - IS 4031 Part 8 (Optional))	-	1000	OK
Clause 7 Table 2 SI No. (v) (Transverse Strength, 672 ± 4 h)	-	1000	OK
Clause 7Table 2 SI No. (v)(Transverse Strength, 168 ± 2 h)	-	1000	OK
Clause 7Table 2 SI No. (v)(Transverse Strength, 72 ± 1 h)	-	1000	OK
11(Marking)	-	250	OK
11(MARKING)	-	250	OK
Clause 7 Table 2 SI No. (v) (Compressive strength of Transverse Specimen, 672 ± 4 h)	-	1000	OK
Clause 7 Table 2 SI No. (v) (Compressive strength of Transverse Specimen, 168 ± 2 h)	-	1000	OK
Clause 7 Table 2 SI No. (v) (Compressive strength of Transverse Specimen, 72 ± 1 h)	-	1000	OK
4(RAW MATERIAL)	-	500	OK
Clause 7 Table 2 SI No. (v) (Transverse Strength, 672 ± 4 h)	-	1000	OK
Clause 7Table 2 SI No. (v)(Transverse Strength, 168 ± 2 h)	-	1000	OK
Clause 7Table 2 SI No. (v)(Transverse Strength, 72 ± 1 h)	-	1000	OK
11(Marking)	-	250	OK
11(MARKING)	-	250	OK
Clause 7 Table 2 SI No. (v) (Compressive strength of Transverse Specimen, 672 ± 4 h)	-	500	ok
Clause 7 Table 2 SI No. (v) (Compressive strength of Transverse Specimen, 168 ± 2 h)	-	500	ok
Clause 7 Table 2 SI No. (v) (Compressive strength of Transverse Specimen, 72 ± 1 h)	-	500	ok
4(RAW MATERIAL)	-	500	ok
Clause 7 Table 2 SI No. (v) (Transverse Strength, 672 ± 4 h)	-	1000	ok
Clause 7Table 2 SI No. (v)(Transverse Strength, 168 ± 2 h)	-	1000	ok
Clause 7Table 2 SI No. (v)(Transverse Strength, 72 ± 1 h)	-	1000	ok
11(Marking)	-	250	ok
11(MARKING)	-	250	ok

15 May, 2027

-
Included w.e.f.09.04.2025

6986

Precision Laboratories LLP, Ahmedabad

7174106

IS 303 (2024)

Plywood for General Purposes â Specification (Fourth Revision)

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.1(Classification by appearance)	-	3000	-
Cl-5.2, Table- 1 (i)(Blister)	-	3000	-
Cl-5.2, Table- 1 (ii)(Checks)	-	3000	-
Cl-5.2, Table- 1 (iii)(Discolouration)	-	3000	-
Cl-5.2, Table- 1 (iv)(Dote)	-	3000	-
Cl-5.2, Table- 1 (v)(Insect hole)	-	3000	-
Cl-5.2, Table- 1 (vi)(Joints)	-	3000	-
Cl-5.2, Table- 1 (vii)(Knots (dead))	-	3000	-
Cl-5.2, Table- 1 (viii)(Pin knots (dead))	-	3000	-
Cl-5.2, Table- 1 (ix)(Pin knots (live))	-	3000	-
Cl-5.2, Table- 1 (x)(Knots (tight))	-	3000	-
Cl-5.2, Table- 1 (xi)(Patches)	-	3000	-
Cl-5.2, Table- 1 (xii)(Splits)	-	3000	-
Cl-5.2, Table- 1 (xiii)(Swirl)	-	3000	-
Cl-5.2, Table-2(Maximum Number of Categories of Permissible Defects, per m2)	-	3000	-
Cl-6.1(Timber)	-	3000	-
Cl-6.2(Adhesive)	-	3000	-
Cl-7.2.1(Thickness of veneers)	-	3000	-
Cl-7.2.3(Grain Direction)	-	3000	-
Cl-7.2.5.1(Gaps in cores and cross-bands)	-	3000	-
Cl-7.2.5.2(Splits)	-	3000	-
Cl-7.2.5.3(Overlap)	-	3000	-
Cl-8.1(Dimensions -length)	-	3000	-
Cl-8.2(Thickness of the plywood boards)	-	3000	-
Cl-8.3(Squareness)	-	3000	-
Cl-11.3.1, 11.3.1.1(Water Resistance Test)	-	3000	-
Cl-11.3.2(Mycological Test)	-	3000	-
Cl-11.4(Moisture Content)	-	3000	-
Cl-11.5, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average)	-	3000	-
Cl-11.5, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Minimum Individual)	-	3000	-
Cl-11.6(Formaldehyde Content Test)	-	3000	-
Cl-11.7(Steady-State Formaldehyde Emission Test)	-	3000	-
Cl-9(WORKMANSHIP AND FINISH)	-	3000	-
Cl-7.2.4(Scarf Joints)	-	3000	-
Cl-5.1(Classification by appearance)	-	3000	-
Cl-5.2, Table- 1 (i)(Blister)	-	3000	-
Cl-5.2, Table- 1 (ii)(Checks)	-	3000	-
Cl-5.2, Table- 1 (iii)(Discolouration)	-	3000	-
Cl-5.2, Table- 1 (iv)(Dote)	-	3000	-
Cl-5.2, Table- 1 (v)(Insect hole)	-	3000	-
Cl-5.2, Table- 1 (vi)(Joints)	-	3000	-
Cl-5.2, Table- 1 (vii)(Knots (dead))	-	3000	-
Cl-5.2, Table- 1 (viii)(Pin knots (dead))	-	3000	-
Cl-5.2, Table- 1 (ix)(Pin knots (live))	-	3000	-
Cl-5.2, Table- 1 (x)(Knots (tight))	-	3000	-
Cl-5.2, Table- 1 (xi)(Patches)	-	3000	-
Cl-5.2, Table- 1 (xii)(Splits)	-	3000	-
Cl-5.2, Table- 1 (xiii)(Swirl)	-	3000	-
Cl-5.2, Table-2(Maximum Number of Categories of Permissible Defects, per m2)	-	3000	-
Cl-6.1(Timber)	-	3000	-
Cl-6.2(Adhesive)	-	3000	-
Cl-7.2.1(Thickness of veneers)	-	3000	-
Cl-7.2.3(Grain Direction)	-	3000	-
Cl-7.2.5.1(Gaps in cores and cross-bands)	-	3000	-
Cl-7.2.5.2(Splits)	-	3000	-
Cl-7.2.5.3(Overlap)	-	3000	-
Cl-8.1(Dimensions -length)	-	3000	-
Cl-8.2(Thickness of the plywood boards)	-	3000	-
Cl-8.3(Squareness)	-	3000	-
Cl-11.3.1, 11.3.1.1(Water Resistance Test)	-	3000	-
Cl-11.3.2(Mycological Test)	-	3000	-
Cl-11.4(Moisture Content)	-	3000	-
Cl-11.5, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average)	-	3000	-
Cl-11.5, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Minimum Individual)	-	3000	-
Cl-11.6(Formaldehyde Content Test)	-	3000	-
Cl-11.7(Steady-State Formaldehyde Emission Test)	-	3000	-
Cl-9(WORKMANSHIP AND FINISH)	-	3000	-
Cl-7.2.4(Scarf Joints)	-	3000	-

31 Oct, 2029

-
Included w.e.f 04.03.2025 Exclusion:Cl-11.7 (Steady-State Formaldehyde Emission Test)

6987

IDMA LABORATORIES LIMITED, PANCHKULA

9123236

IS 5405 (2019)

Sanitary napkins – Specification (second revision)

260200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5(SIZES, Regular )	-	1500	Rs. 1550/- for dimensions of all sizes
6.0(Manufacture, workmanship & finish)	-	500	Rs. 20,200/- Excluding Biocompatibility Evaluation – Cytotoxicity, Irritation & Skin Sensitization (as per cl. no. 7.4) & Biodegradability (Clause 7.5).
Cl 7.1(pH Value, IS 1390 (cold method) for all sizes)	-	700	OK
Cl 7.2(Ability to Withstand Pressure after Absorption, for all sizes, Annex B)	-	1500	OK
Cl 7.3.1(Bacterial and Fungal Bioburden, 7.3.1.1, ISO 11737 (Part 1))	-	3000	OK
Cl7.3.2(Test for Common Skin Pathogen — Staphylococcus Aureus, 7.3.2.1, IS 5887 (Part 2))	-	3000	OK
Cl 7.4(Biocompatibility Evaluation — Cytotoxicity, Irritation and Skin Sensitization, IS/ISO 10993 Part 5 and IS/ISO 10993 Part 10)	-	240000	Rs. 2,60,200/- Including Biocompatibility Evaluation – Cytotoxicity, Irritation & Skin Sensitization (as per cl. no. 7.4). Excluding Biodegradability (Clause 7.5)
Cl 7.5(Biodegradability and Compostability (Optional), IS/ISO 17088.)	-	0	Marked for exclusion
7.6(Pthalate test)	-	10000	Testing charges for Clause no. 7.6, Pthalate test are Rs. 8500/- for all the 7 parameters as listed below. i) DBP ii)BBP iii) DEHP iv) DNOP v) DINP vi) DIDP vii) DIBP
Cl 5(SIZES, Regular )	-	0	As above
6.0(Manufacture, workmanship & finish)	-	0	As above
Cl 7.1(pH Value, IS 1390 (cold method) for all sizes)	-	0	As above
Cl 7.2(Ability to Withstand Pressure after Absorption, for all sizes, Annex B)	-	0	As above
Cl 7.3.1(Bacterial and Fungal Bioburden, 7.3.1.1, ISO 11737 (Part 1))	-	0	As above
Cl7.3.2(Test for Common Skin Pathogen — Staphylococcus Aureus, 7.3.2.1, IS 5887 (Part 2))	-	0	As above
Cl 7.4(Biocompatibility Evaluation — Cytotoxicity, Irritation and Skin Sensitization, IS/ISO 10993 Part 5 and IS/ISO 10993 Part 10)	-	0	As above
7.6(Pthalate test)	-	0	As above

31 Dec, 2026

-
-

6988

Standard Testing and Compliance Private Limited

6178726

IS 302 : Part 1 (2024)

Household and Similar Electrical Appliances â Safety Part 1 General Requirements (Seventh Revision)

54000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
12(Charging of metal-ion batteries)	-	0	15% discount to BIS
6(Classification- IS 302-1)	-	0	15% discount to BIS
5(General conditions for the tests)	-	0	15% discount to BIS
11.8(Temperature rise)	-	1000	15% discount to BIS
11.7(Duration corresponding)	-	0	15% discount to BIS
11.6(Combined appliances)	-	0	15% discount to BIS
11.5(Motor-operated appliances)	-	0	15% discount to BIS
11.4(Heating appliances)	-	0	15% discount to BIS
8.1.5(Live parts of built-in appliances)	-	0	15% discount to BIS
17(Overload protection of transformers and associated circuits)	-	2500	15% discount to BIS
16(Leakage current and electric strength)	-	2500	15% discount to BIS
4(General requirement)	-	0	15% discount to BIS
31(Resistance to Rusting)	-	500	15% discount to BIS
30.2(Needle Flame Test)	-	1000	15% discount to BIS
30.2(Glow Wire Test)	-	500	15% discount to BIS
30.1(Ball pressure test)	-	1000	15% discount to BIS
29(clearance, creepage distances and solid insulation)	-	2500	15% discount to BIS
28(Screw test and connections)	-	2500	15% discount to BIS
27.1(Provision for Earthing, IS 302-1)	-	2500	15% discount to BIS
26(Terminals for external conductors)	-	2500	15% discount to BIS
25.8(Supply Connection and External Flexible Cords, IS 302-1)	-	2500	15% discount to BIS
23.1(Internal Wiring, IS 302-1)	-	2500	15% discount to BIS
22.1(Construction, IS 302-1)	-	2500	15% discount to BIS
21.1(Mechanical Strength, IS 302-1)	-	2500	15% discount to BIS
20.1(Stability & Mechanical Hazards, IS 302-1)	-	1000	15% discount to BIS
19(Abnormal Operation)	-	1500	15% discount to BIS
17(Over Load Protection of Transformers and associated circuits)	-	2500	15% discount to BIS
16.3(Electric Strength (after clause 15 and 16.2))	-	0	15% discount to BIS
16.2(Leakage Current (after Clause 15))	-	0	15% discount to BIS
16.1(General)	-	0	15% discount to BIS
16.0(General)	-	0	15% discount to BIS
15.3(Humidity Test)	-	3000	15% discount to BIS
15.2(Spillage Test)	-	0	15% discount to BIS
15.1(Ingress Protection test other than IPX0 (IP test))	-	1000	15% discount to BIS
15.0(Moisture resistance)	-	1000	15% discount to BIS
14(Transient Over Voltages)	-	2500	15% discount to BIS
13.3(Electric Strength at operating temperature)	-	1000	15% discount to BIS
13.2(Leakage current at operating temperature)	-	1000	15% discount to BIS
13(Leakage current and electric strength at operating temperature)	-	500	15% discount to BIS
11.3(Heating)	-	1500	15% discount to BIS
11.2(General)	-	0	15% discount to BIS
11.1(General)	-	0	15% discount to BIS
10.2(Current input)	-	1000	15% discount to BIS
10.1(Power input)	-	1500	15% discount to BIS
8.1.4(Protection against live parts against protective impedance)	-	1000	-
8.1.3(Protection against live parts in visible glowing heating elements)	-	500	15% discount to BIS
8.1.2(Protection against live parts in openings)	-	1000	15% discount to BIS
8.1.1(Protection against live parts in all positions)	-	1000	15% discount to BIS
7(Marking and instructions)	-	2500	15% discount to BIS
A.2(Earth continuity test)	-	0	15% discount to BIS
15.2(Moisture resistance)	-	0	15% discount to BIS
19.17(Abnormal Operation, IS 302-1)	-	0	15% discount to BIS
20.2(Stability & Mechanical Hazards, IS 302-1)	-	0	15% discount to BIS
21.2(Mechanical Strength, IS 302-1)	-	0	15% discount to BIS
21.3(Mechanical Strength, IS 302-1)	-	0	15% discount to BIS
22.5(Construction)	-	0	15% discount to BIS
22.6(Construction, IS 302-1)	-	0	15% discount to BIS
22.11(Construction, IS 302-1)	-	0	15% discount to BIS
22.16(Construction)	-	0	15% discount to BIS
22.42(Construction)	-	0	15% discount to BIS
23.3(Internal Wiring, IS 302-1)	-	0	15% discount to BIS
25.6(Supply connection and external flexible cords, IS 302-1)	-	0	15% discount to BIS
25.7(Supply Connection and External Flexible Cords, IS 302-1)	-	0	15% discount to BIS
25.14(Supply Connection and External Flexible Cords, IS 302-1)	-	0	15% discount to BIS
25.15(Supply Connection and External Flexible Cords, IS 302-1)	-	0	15% discount to BIS
26.5(Terminals for external conductors)	-	0	15% discount to BIS
27.5(Provision for Earthing, IS 302-1)	-	0	15% discount to BIS
28.1(Screws and connections)	-	0	15% discount to BIS
12(Charging of metal-ion batteries)	-	0	15% discount to BIS
6(Classification- IS 302-1)	-	0	15% discount to BIS
5(General conditions for the tests)	-	0	15% discount to BIS
11.8(Temperature rise)	-	0	15% discount to BIS
11.7(Duration corresponding)	-	0	15% discount to BIS
11.6(Combined appliances)	-	0	15% discount to BIS
11.5(Motor-operated appliances)	-	0	15% discount to BIS
11.4(Heating appliances)	-	0	15% discount to BIS
8.1.5(Live parts of built-in appliances)	-	0	15% discount to BIS
17(Overload protection of transformers and associated circuits)	-	0	15% discount to BIS
16(Leakage current and electric strength)	-	0	15% discount to BIS
4(General requirement)	-	0	15% discount to BIS
31(Resistance to Rusting)	-	0	15% discount to BIS
30.2(Needle Flame Test)	-	0	15% discount to BIS
30.2(Glow Wire Test)	-	0	15% discount to BIS
30.1(Ball pressure test)	-	0	15% discount to BIS
29(clearance, creepage distances and solid insulation)	-	0	15% discount to BIS
28(Screw test and connections)	-	0	15% discount to BIS
27.1(Provision for Earthing, IS 302-1)	-	0	15% discount to BIS
26(Terminals for external conductors)	-	0	15% discount to BIS
25.8(Supply Connection and External Flexible Cords, IS 302-1)	-	0	15% discount to BIS
23.1(Internal Wiring, IS 302-1)	-	0	15% discount to BIS
22.1(Construction, IS 302-1)	-	0	15% discount to BIS
21.1(Mechanical Strength, IS 302-1)	-	0	15% discount to BIS
20.1(Stability & Mechanical Hazards, IS 302-1)	-	0	15% discount to BIS
19(Abnormal Operation)	-	0	15% discount to BIS
17(Over Load Protection of Transformers and associated circuits)	-	0	15% discount to BIS
16.3(Electric Strength (after clause 15 and 16.2))	-	0	15% discount to BIS
16.2(Leakage Current (after Clause 15))	-	0	15% discount to BIS
16.1(General)	-	0	15% discount to BIS
16.0(General)	-	0	15% discount to BIS
15.3(Humidity Test)	-	0	15% discount to BIS
15.2(Spillage Test)	-	0	15% discount to BIS
15.1(Ingress Protection test other than IPX0 (IP test))	-	0	15% discount to BIS
15.0(Moisture resistance)	-	0	15% discount to BIS
14(Transient Over Voltages)	-	0	15% discount to BIS
13.3(Electric Strength at operating temperature)	-	0	15% discount to BIS
13.2(Leakage current at operating temperature)	-	0	15% discount to BIS
13(Leakage current and electric strength at operating temperature)	-	0	15% discount to BIS
11.3(Heating)	-	0	15% discount to BIS
11.2(General)	-	0	15% discount to BIS
11.1(General)	-	0	15% discount to BIS
10.2(Current input)	-	0	15% discount to BIS
10.1(Power input)	-	0	15% discount to BIS
8.1.4(Protection against live parts against protective impedance)	-	0	15% discount to BIS
8.1.3(Protection against live parts in visible glowing heating elements)	-	0	15% discount to BIS
8.1.2(Protection against live parts in openings)	-	0	15% discount to BIS
8.1.1(Protection against live parts in all positions)	-	0	15% discount to BIS
7(Marking and instructions)	-	0	15% discount to BIS
A.2(Earth continuity test)	-	0	15% discount to BIS
15.2(Moisture resistance)	-	0	15% discount to BIS
19.17(Abnormal Operation, IS 302-1)	-	0	15% discount to BIS
20.2(Stability & Mechanical Hazards, IS 302-1)	-	0	15% discount to BIS
21.2(Mechanical Strength, IS 302-1)	-	0	15% discount to BIS
21.3(Mechanical Strength, IS 302-1)	-	0	15% discount to BIS
22.5(Construction)	-	0	15% discount to BIS
22.6(Construction, IS 302-1)	-	0	15% discount to BIS
22.11(Construction, IS 302-1)	-	0	15% discount to BIS
22.16(Construction)	-	0	15% discount to BIS
22.42(Construction)	-	0	15% discount to BIS
23.3(Internal Wiring, IS 302-1)	-	0	15% discount to BIS
25.6(Supply connection and external flexible cords, IS 302-1)	-	0	15% discount to BIS
25.7(Supply Connection and External Flexible Cords, IS 302-1)	-	0	15% discount to BIS
25.14(Supply Connection and External Flexible Cords, IS 302-1)	-	0	15% discount to BIS
25.15(Supply Connection and External Flexible Cords, IS 302-1)	-	0	15% discount to BIS
26.5(Terminals for external conductors)	-	0	15% discount to BIS
27.5(Provision for Earthing, IS 302-1)	-	0	15% discount to BIS
28.1(Screws and connections)	-	0	15% discount to BIS
12(Charging of metal-ion batteries)	-	0	15% discount to BIS
6(Classification- IS 302-1)	-	0	15% discount to BIS
5(General conditions for the tests)	-	0	15% discount to BIS
11.8(Temperature rise)	-	0	-
11.7(Duration corresponding)	-	0	-
11.6(Combined appliances)	-	0	-
11.5(Motor-operated appliances)	-	0	-
11.4(Heating appliances)	-	0	-
8.1.5(Live parts of built-in appliances)	-	0	-
17(Overload protection of transformers and associated circuits)	-	0	-
16(Leakage current and electric strength)	-	0	-
4(General requirement)	-	0	-
31(Resistance to Rusting)	-	0	-
30.2(Needle Flame Test)	-	0	-
30.2(Glow Wire Test)	-	0	-
30.1(Ball pressure test)	-	0	-
29(clearance, creepage distances and solid insulation)	-	0	-
28(Screw test and connections)	-	0	-
27.1(Provision for Earthing, IS 302-1)	-	0	-
26(Terminals for external conductors)	-	0	-
25.8(Supply Connection and External Flexible Cords, IS 302-1)	-	0	-
23.1(Internal Wiring, IS 302-1)	-	0	-
22.1(Construction, IS 302-1)	-	0	-
21.1(Mechanical Strength, IS 302-1)	-	0	-
20.1(Stability & Mechanical Hazards, IS 302-1)	-	0	-
19(Abnormal Operation)	-	0	-
17(Over Load Protection of Transformers and associated circuits)	-	0	-
16.3(Electric Strength (after clause 15 and 16.2))	-	0	-
16.2(Leakage Current (after Clause 15))	-	0	-
16.1(General)	-	0	-
16.0(General)	-	0	-
15.3(Humidity Test)	-	0	-
15.2(Spillage Test)	-	0	-
15.1(Ingress Protection test other than IPX0 (IP test))	-	0	-
15.0(Moisture resistance)	-	0	-
14(Transient Over Voltages)	-	0	-
13.3(Electric Strength at operating temperature)	-	0	-
13.2(Leakage current at operating temperature)	-	0	-
13(Leakage current and electric strength at operating temperature)	-	0	-
11.3(Heating)	-	0	-
11.2(General)	-	0	-
11.1(General)	-	0	-
10.2(Current input)	-	0	-
10.1(Power input)	-	0	-
8.1.4(Protection against live parts against protective impedance)	-	0	-
8.1.3(Protection against live parts in visible glowing heating elements)	-	0	-
8.1.2(Protection against live parts in openings)	-	0	-
8.1.1(Protection against live parts in all positions)	-	0	-
7(Marking and instructions)	-	0	-
A.2(Earth continuity test)	-	0	-
15.2(Moisture resistance)	-	0	-
19.17(Abnormal Operation, IS 302-1)	-	0	-
20.2(Stability & Mechanical Hazards, IS 302-1)	-	0	-
21.2(Mechanical Strength, IS 302-1)	-	0	-
21.3(Mechanical Strength, IS 302-1)	-	0	-
22.5(Construction)	-	0	-
22.6(Construction, IS 302-1)	-	0	-
22.11(Construction, IS 302-1)	-	0	-
22.16(Construction)	-	0	-
22.42(Construction)	-	0	-
23.3(Internal Wiring, IS 302-1)	-	0	-
25.6(Supply connection and external flexible cords, IS 302-1)	-	0	-
25.7(Supply Connection and External Flexible Cords, IS 302-1)	-	0	-
25.14(Supply Connection and External Flexible Cords, IS 302-1)	-	0	-
25.15(Supply Connection and External Flexible Cords, IS 302-1)	-	0	-
26.5(Terminals for external conductors)	-	0	-
27.5(Provision for Earthing, IS 302-1)	-	0	-
28.1(Screws and connections)	-	0	-

10 Jul, 2027

-
Included w.e.f.25.03.2025 Exclusion Cl 19.11.4.1 to Cl 19.11.4.7 (EMI/EMC) Cl 32 (Radiation Toxicity and Similar Hazards) Cl 24 (Components) Cl 9 (Starting of motor operation test requirements and tests) Cl 18 (Endurance) "Domestic Electric Clothes Washing Machines (For testing charges please refer part 2 standard in LIMS)" 15 – Only IPX9 test facility 22.32 – Test facility for Oxygen Bomb testing 22.16 – Test facility for automatic cord reel.

6989

IDMA LABORATORIES LIMITED, PANCHKULA

9123236

IS 10813 (2022)

SOAP JELLY FOR LAUNDRY PURPOSES â SPECIFICATION

14500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1("Description ( IS 10813: 2022 )")	-	1000	-
4.1("Description ( IS 10813: 2022 )")	-	0	Testing charges already mentioned above
4.2("Solubility ( IS 10813: 2022 )")	-	1000	-
4.3("Storage ( IS 10813: 2022 )")	-	1500	-
4.4("Odour ( IS 10813: 2022 )")	-	1000	-
4.5("Stability at 0°C ( IS 10813: 2022 )")	-	2000	-
4.6 Table 1 (i)("Total fatty matter ( IS 286: 2018 )")	-	3000	-
4.6 Table 1 (ii)("Matter insoluble in water ( IS 286: 2018 )")	-	2500	-
4.6 Table 1 (iii)("Free caustic alkali, as sodium hydroxide (NaOH) ( IS 286: 2018 )")	-	2500	-

31 Dec, 2026

-
Included w.e.f.24.04.2025

6990

IDMA LABORATORIES LIMITED, PANCHKULA

9123236

IS 8367 (2023)

TIN POWDER ï¿½ SPECIFICATION

Grade A, Grade B, Grade C, Grade D

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(Supply of material)	-	0	NA
Cl-5(Manufacture)	-	0	NA
Cl-6(Grades)	-	0	NA
Cl-7.1, Table-1 (i)(Tin)	-	1500	-
Cl-7.1, Table-1 (ii)(Lead)	-	1500	-
Cl-7.1, Table-1 (iii)(Antimony)	-	1500	-
Cl-7.1, Table-1 (iv)(Copper)	-	1500	-
Cl-7.1, Table-1 (v)(Bismuth)	-	1500	-
Cl-7.1, Table-1 (vi)(Iron)	-	1500	-
Cl-7.1, Table-1 (vii)(Arsenic)	-	1500	-
Cl-7.1, Table-1 (viii)(Other impurities)	-	1500	-
Cl-7.1, Table-1 (ix)(Hydrogen loss)	-	3000	-
Cl-8.1(Apparent Density)	-	2500	-
Cl-8.2(Flow Rate)	-	2500	-
Cl-11(Marking)	-	0	NA
Cl-7.2(Chemical analysis)	-	0	NA
Cl-7.3(Hydrogen loss)	-	0	Testing charges already mentioned above.

31 Dec, 2026

-
Included w.e.f.24.04.2025

Bureau of Indian Standards

The National Standards Body of India

Search by IS Number