BIS - LIMS (Laboratory Information Management System)

Search by IS Number

Reset

15623 Results

S.No.

Lab Name

Osl Code

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

7021

DELHI TEST HOUSE, Azadhpur

8131406

IS 739 (1992)

Wrought aluminium and aluminium alloys - Wire for general engineering purposes - Specification (Third Revision)

ALL

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.0(Freedom from defects)	-	500	COMPLETE TESTING CHARGES - 12500/-
7.0(Dimension and Tolerances)	-	500	COMPLETE TESTING CHARGES - 12500/-
8.1 Table-1(Al)	-	500	COMPLETE TESTING CHARGES - 12500/-
8.1 Table-1(Cu)	-	500	COMPLETE TESTING CHARGES - 12500/-
8.1 Table-1(Mg)	-	500	COMPLETE TESTING CHARGES - 12500/-
8.1 Table-1(Si)	-	500	COMPLETE TESTING CHARGES - 12500/-
8.1 Table-1(Fe)	-	500	COMPLETE TESTING CHARGES - 12500/-
8.1 Table-1(Mn)	-	500	COMPLETE TESTING CHARGES - 12500/-
8.1 Table-1(Zn)	-	500	COMPLETE TESTING CHARGES - 12500/-
8.1 Table-1(Ti)	-	500	COMPLETE TESTING CHARGES - 12500/-
8.1 Table-1(Cr)	-	500	COMPLETE TESTING CHARGES - 12500/-
9.1(Tensile Strength)	-	5000	COMPLETE TESTING CHARGES - 12500/-
9.3(Wrapping Test)	-	1500	COMPLETE TESTING CHARGES - 12500/-
10(Selection of Test Samples)	-	0	COMPLETE TESTING CHARGES - 12500/-
10(Selection of Test Samples)	-	0	COMPLETE TESTING CHARGES - 12500/-
10(Selection of Test Samples)	-	0	-
10(Selection of Test Samples)	-	0	-
10(Selection of Test Samples)	-	-	-

17 Jun, 2027

-
Included .w.e.f.03.03.2025

7022

VARDAN ENVIROLAB, GURUGRAM

8169616

IS 13893 (1994)

Polyurethane soles semirigid - specification

Polyurethane Soles Semirigid

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.3.2(Ageing test)	-	2700	-
4.3(Ross Flex test)	-	2000	-
4.3(Flexural strength )	-	2000	-
4.3(Abrasion Resistance)	-	1080	-
4.3(Elongation at break)	-	500	-
4.3(Tensile Strength )	-	500	-
4.3(Hardness Shore(A))	-	300	-
4.3(Relative density )	-	300	-
4.2(Thickness )	-	180	-
4.1(Design)	-	150	-
5, 5.1, 5.2(Packing And Marking)	-	180	-
Cl.5, 5.1, 5.2(Packing And Marking)	-	180	-
4.2 (Amendment 2)(Thickness)	-	100	-
4.3.1 Table 1 i) (Amendment 2)(Relative Density)	-	300	-
4.3.1 Table 1 iii) (Amendment 2)(Abrasion Resistance at applied force of 10 N)	-	1080	-
4.3.1 Table 1 iv) (Amendment 2)(Flexing Resistance, Bennewart method)	-	1080	-
4.3.1 Table 1 v) (Amendment 2)(Hydrolysis Resistance, cut growth after 150000 flexes)	-	2700	-
4.3.1 Table 1 vi) (Amendment 2)(Tensile Strength)	-	250	-
4.3.1 Table 1 vii) (Amendment 2)(Elongation at break)	-	250	-
4.3.1 Table 1 viii) (Amendment 2)(Tear Strength (average force))	-	500	-
4.3.1 Table 1 ii) (Amendment 2)(Hardness, degree, Shore A)	-	600	-

26 Dec, 2027

-
-

7023

Bombay Textiles Research Association (BTRA), Mumbai

7130206

IS 17261 (2022)

Textiles - Polyester continuous filament fully drawn yarns - Specification (first revision)

96160 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.2 & Table-4(Moisture regain ( IS17261))	-	500	-
6.2 & Table-4(Anti-microbial activity value (IS/ISO 20743))	-	4800	-
6.2 & Table-4(Water soluble matter (IS 3456))	-	1000	-
6.2 & Table-4(Finish oil pick-up ( IS17261))	-	1000	-
5.2(Identification and Description, Annex J of IS 16481 & IS 667)	-	0	-
6.2 & Table-4(Phosphorus content ( IS17261))	-	1000	-
6.2 & Table-4(Ultraviolet resistance (IS 13162 (Part-2))	-	46000	-
6.2 & Table-4(Ultraviolet resistance (IS 13162 (Part-2))	-	0	ALREADY GIVEN
6.2 & Table-4(Colour strength with reference to standard yarn ( IS17261))	-	760	-
6.2 & Table-4(Colour difference with reference to standard yarn, measured as ΔE ( IS17261))	-	760	-
6.4 & Table-5(Lustre/Brightness TiO2 Content)	-	1500	-
6.5 & Table-6(Colour Fastness Rating To Light Change in colour)	-	2500	-
6.5 & Table-7(Colour Fastness Rating To Washing Change in colour)	-	500	-
6.5 & Table-8(Colour Fastness Rating To Washing Staining)	-	0	ALREADY GIVEN
6.5 & Table-9(Colour Fastness Rating To Rubbing Dry)	-	260	-
6.5 & Table-10(Colour Fastness Rating To Rubbing Wet)	-	0	ALREADY GIVEN
6.5 & Table-11(Colour Fastness Rating To Perspiration (acidic and alkaline) Change in colour)	-	550	-
6.5 & Table-12(Colour Fastness Rating To Perspiration (acidic and alkaline) Staining)	-	0	ALREADY GIVEN
6.7 & Table 7(Colour Fastness Rating To Light Change in colour (IS/ISO 105-B01 or IS/ISO 105-B02))	-	0	ALREADY GIVEN
6.5 Table 6(Colour Fastness to Light)	-	0	ALREADY GIVEN
6.5 Table 6(Colour Fatness to Washing, Test 2)	-	0	ALREADY GIVEN
6.5 Table 6(Colour Fastness to Rubbing)	-	0	ALREADY GIVEN
6.5 Table 6(Colour Fastness to perspiration)	-	0	ALREADY GIVEN
6.2 Table 4(Moisture Regain , %)	-	0	ALREADY GIVEN
6.2 Table 4(Water soluble matter %)	-	0	ALREADY GIVEN
6.2 Table 4(Finish oil pickup, %)	-	0	ALREADY GIVEN
6.2 Table 4(Phosphorus content , %)	-	0	ALREADY GIVEN
6.2 Table 4(Phosphorus content , %)	-	0	ALREADY GIVEN
6.2 Table 4(Colour strength with refernce to standard yarn, %)	-	0	ALREADY GIVEN
6.2 Table 4(Colour difference with referece standard yarn, measure as DE)	-	0	ALREADY GIVEN
6.2 & Table-4(Isophthalic acid (IPA) content (IS 16481))	-	6000	-
6.7 & table-7(Free and releasable formaldehyde)	-	2500	-
6.7 & table-7(Mercury (IS 15651))	-	5000	-
6.7 & table-7(Chromium VI (IS 15651))	-	0	ALREADY GIVEN
6.7 & table-7(Lead (IS 15651))	-	0	ALREADY GIVEN
6.7 & table-7(Cadmium (IS 15651))	-	0	ALREADY GIVEN
6.7 & table-7(Copper (IS 15651))	-	0	ALREADY GIVEN
6.7 & table-7(Antimony (IS 15651))	-	0	ALREADY GIVEN
6.7 & table-7(Pentachlorophenol (IS 15651))	-	3000	-
6.7 & table-7(Banned azo colourants (arylamines) (IS 15570))	-	4500	-
6.2- Table -4, Sl no. 2 (a)(Isophthalic acid (IPA) content in Virgin polyester yarn, Percent, Annex C of IS 16481)	-	0	ALREADY GIVEN
6.2- Table -4, Sl no. 2 (b)(Isophthalic acid (IPA) content in Dope dyed/white yarn, Percent, Annex C of IS 16482)	-	0	ALREADY GIVEN
6.2- Table -4, Sl no. 2 (c)(Isophthalic acid (IPA) content in Recycled polyester yarn, Percent, Annex C of IS 16483)	-	0	ALREADY GIVEN
6.1 & Table-3(Linear Density)	-	500	-
6.1 & Table-3(Tenacity)	-	800	-
6.1 & Table-3(Elongation)	-	0	ALREADY GIVEN
6.1 Table -3(No. of filaments in multifilament yarn)	-	1000	-
6.1 Table 3(Linear Density ,Denier (dtex))	-	0	ALREADY GIVEN
6.1 Table 3(Tenacity,gpd (cN/dtex))	-	0	ALREADY GIVEN
6.1 Table 3(Elongation %)	-	0	ALREADY GIVEN
4(Classification (IS 17261))	-	2970	-
6.1 Table -3(Boiling water shrinkage, IS 17087)	-	500	-
6.1 Table -3(Interlace as nips per metre, Annex B of IS 17262)	-	500	-
6.1 Table 3(Boiling Water Shrinkage %)	-	0	ALREADY GIVEN
6.6(Commercial Mass, IS 7703)	-	1000	-
6.2 & Table-4(Moisture regain ( IS17261))	-	0	-
6.2 & Table-4(Anti-microbial activity value (IS/ISO 20743))	-	0	-
6.2 & Table-4(Water soluble matter (IS 3456))	-	0	-
6.2 & Table-4(Finish oil pick-up ( IS17261))	-	0	-
5.2(Identification and Description, Annex J of IS 16481 & IS 667)	-	6760	-
6.2 & Table-4(Phosphorus content ( IS17261))	-	0	-
6.2 & Table-4(Ultraviolet resistance (IS 13162 (Part-2))	-	0	-
6.2 & Table-4(Ultraviolet resistance (IS 13162 (Part-2))	-	0	-
6.2 & Table-4(Colour strength with reference to standard yarn ( IS17261))	-	0	-
6.2 & Table-4(Colour difference with reference to standard yarn, measured as ΔE ( IS17261))	-	0	-
6.4 & Table-5(Lustre/Brightness TiO2 Content)	-	0	-
6.5 & Table-6(Colour Fastness Rating To Light Change in colour)	-	0	-
6.5 & Table-7(Colour Fastness Rating To Washing Change in colour)	-	0	-
6.5 & Table-8(Colour Fastness Rating To Washing Staining)	-	0	-
6.5 & Table-9(Colour Fastness Rating To Rubbing Dry)	-	0	-
6.5 & Table-10(Colour Fastness Rating To Rubbing Wet)	-	0	-
6.5 & Table-11(Colour Fastness Rating To Perspiration (acidic and alkaline) Change in colour)	-	0	-
6.5 & Table-12(Colour Fastness Rating To Perspiration (acidic and alkaline) Staining)	-	0	-
6.7 & Table 7(Colour Fastness Rating To Light Change in colour (IS/ISO 105-B01 or IS/ISO 105-B02))	-	0	-
6.5 Table 6(Colour Fastness to Light)	-	0	-
6.5 Table 6(Colour Fatness to Washing, Test 2)	-	0	-
6.5 Table 6(Colour Fastness to Rubbing)	-	0	-
6.5 Table 6(Colour Fastness to perspiration)	-	0	-
6.2 Table 4(Moisture Regain , %)	-	0	-
6.2 Table 4(Water soluble matter %)	-	0	-
6.2 Table 4(Finish oil pickup, %)	-	0	-
6.2 Table 4(Phosphorus content , %)	-	0	-
6.2 Table 4(Phosphorus content , %)	-	0	-
6.2 Table 4(Colour strength with refernce to standard yarn, %)	-	0	-
6.2 Table 4(Colour difference with referece standard yarn, measure as DE)	-	0	-
6.2 & Table-4(Isophthalic acid (IPA) content (IS 16481))	-	0	-
6.7 & table-7(Free and releasable formaldehyde)	-	0	-
6.7 & table-7(Mercury (IS 15651))	-	0	-
6.7 & table-7(Chromium VI (IS 15651))	-	0	-
6.7 & table-7(Lead (IS 15651))	-	0	-
6.7 & table-7(Cadmium (IS 15651))	-	0	-
6.7 & table-7(Copper (IS 15651))	-	0	-
6.7 & table-7(Antimony (IS 15651))	-	0	-
6.7 & table-7(Pentachlorophenol (IS 15651))	-	0	-
6.7 & table-7(Banned azo colourants (arylamines) (IS 15570))	-	0	-
6.2- Table -4, Sl no. 2 (a)(Isophthalic acid (IPA) content in Virgin polyester yarn, Percent, Annex C of IS 16481)	-	0	-
6.2- Table -4, Sl no. 2 (b)(Isophthalic acid (IPA) content in Dope dyed/white yarn, Percent, Annex C of IS 16482)	-	0	-
6.2- Table -4, Sl no. 2 (c)(Isophthalic acid (IPA) content in Recycled polyester yarn, Percent, Annex C of IS 16483)	-	0	-
6.1 & Table-3(Linear Density)	-	0	-
6.1 & Table-3(Tenacity)	-	0	-
6.1 & Table-3(Elongation)	-	0	-
6.1 Table -3(No. of filaments in multifilament yarn)	-	0	-
6.1 Table 3(Linear Density ,Denier (dtex))	-	0	-
6.1 Table 3(Tenacity,gpd (cN/dtex))	-	0	-
6.1 Table 3(Elongation %)	-	0	-
4(Classification (IS 17261))	-	0	-
6.1 Table -3(Boiling water shrinkage, IS 17087)	-	0	-
6.1 Table -3(Interlace as nips per metre, Annex B of IS 17262)	-	0	-
6.1 Table 3(Boiling Water Shrinkage %)	-	0	-
6.6(Commercial Mass, IS 7703)	-	0	-
6.2 & Table-4(Moisture regain ( IS17261))	-	0	-
6.2 & Table-4(Anti-microbial activity value (IS/ISO 20743))	-	0	-
6.2 & Table-4(Water soluble matter (IS 3456))	-	0	-
6.2 & Table-4(Finish oil pick-up ( IS17261))	-	0	-
5.2(Identification and Description, Annex J of IS 16481 & IS 667)	-	0	-
6.2 & Table-4(Phosphorus content ( IS17261))	-	0	-
6.2 & Table-4(Ultraviolet resistance (IS 13162 (Part-2))	-	0	-
6.2 & Table-4(Ultraviolet resistance (IS 13162 (Part-2))	-	0	-
6.2 & Table-4(Colour strength with reference to standard yarn ( IS17261))	-	0	-
6.2 & Table-4(Colour difference with reference to standard yarn, measured as ΔE ( IS17261))	-	0	-
6.4 & Table-5(Lustre/Brightness TiO2 Content)	-	0	-
6.5 & Table-6(Colour Fastness Rating To Light Change in colour)	-	0	-
6.5 & Table-7(Colour Fastness Rating To Washing Change in colour)	-	0	-
6.5 & Table-8(Colour Fastness Rating To Washing Staining)	-	0	-
6.5 & Table-9(Colour Fastness Rating To Rubbing Dry)	-	0	-
6.5 & Table-10(Colour Fastness Rating To Rubbing Wet)	-	0	-
6.5 & Table-11(Colour Fastness Rating To Perspiration (acidic and alkaline) Change in colour)	-	0	-
6.5 & Table-12(Colour Fastness Rating To Perspiration (acidic and alkaline) Staining)	-	0	-
6.7 & Table 7(Colour Fastness Rating To Light Change in colour (IS/ISO 105-B01 or IS/ISO 105-B02))	-	0	-
6.5 Table 6(Colour Fastness to Light)	-	0	-
6.5 Table 6(Colour Fatness to Washing, Test 2)	-	0	-
6.5 Table 6(Colour Fastness to Rubbing)	-	0	-
6.5 Table 6(Colour Fastness to perspiration)	-	0	-
6.2 Table 4(Moisture Regain , %)	-	0	-
6.2 Table 4(Water soluble matter %)	-	0	-
6.2 Table 4(Finish oil pickup, %)	-	0	-
6.2 Table 4(Phosphorus content , %)	-	0	-
6.2 Table 4(Phosphorus content , %)	-	0	-
6.2 Table 4(Colour strength with refernce to standard yarn, %)	-	0	-
6.2 Table 4(Colour difference with referece standard yarn, measure as DE)	-	0	-
6.2 & Table-4(Isophthalic acid (IPA) content (IS 16481))	-	0	-
6.7 & table-7(Free and releasable formaldehyde)	-	0	-
6.7 & table-7(Mercury (IS 15651))	-	0	-
6.7 & table-7(Lead (IS 15651))	-	0	-
6.7 & table-7(Cadmium (IS 15651))	-	0	-
6.7 & table-7(Copper (IS 15651))	-	0	-
6.7 & table-7(Antimony (IS 15651))	-	0	-
6.7 & table-7(Pentachlorophenol (IS 15651))	-	0	-
6.7 & table-7(Banned azo colourants (arylamines) (IS 15570))	-	0	-
6.2- Table -4, Sl no. 2 (a)(Isophthalic acid (IPA) content in Virgin polyester yarn, Percent, Annex C of IS 16481)	-	0	-
6.2- Table -4, Sl no. 2 (b)(Isophthalic acid (IPA) content in Dope dyed/white yarn, Percent, Annex C of IS 16482)	-	0	-
6.2- Table -4, Sl no. 2 (c)(Isophthalic acid (IPA) content in Recycled polyester yarn, Percent, Annex C of IS 16483)	-	0	-
6.1 & Table-3(Linear Density)	-	0	-
6.1 & Table-3(Tenacity)	-	0	-
6.1 & Table-3(Elongation)	-	0	-
6.1 Table -3(No. of filaments in multifilament yarn)	-	0	-
6.1 Table 3(Linear Density ,Denier (dtex))	-	0	-
6.1 Table 3(Tenacity,gpd (cN/dtex))	-	0	-
6.1 Table 3(Elongation %)	-	0	-
4(Classification (IS 17261))	-	0	-
6.1 Table -3(Boiling water shrinkage, IS 17087)	-	0	-
6.1 Table -3(Interlace as nips per metre, Annex B of IS 17262)	-	0	-
6.1 Table 3(Boiling Water Shrinkage %)	-	0	-
6.6(Commercial Mass, IS 7703)	-	0	-

-
Included w.e.f 26.05.2025

7024

SIIR, Delhi Shriram Institute For Industrial Research

8102006

IS 4783 (2024)

Thiram powder for dry seed treatment - Specification (second revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2.1(Description - IS 4783:2024)	-	2000	30% Discount
3.2.2(Colour - IS 4783:2024)	-	1000	30% Discount
3.2.3(Sieving Requirement 150 micron sieve - IS 4783:2024)	-	2000	30% Discount
3.3.1.(Thiram Content - IS 4320:2024)	-	5000	30% Discount

31 Dec, 2026

-
Included w.e.f 29.07.2025

7025

VARDAN ENVIROLAB, GURUGRAM

8169616

IS 5676 (1995)

Moulded solid rubber soles and heels - SpecificatlOn (Second Revision)

Moulded Solid Rubber Soles And Heels

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5/5.3/5.3.1(REQUIREMENTS- Construction)	-	150	-
5/5.1(REQUIREMENTS-General)	-	100	-
5/5.2- Fig. 1 to 5(REQUIREMENTS-Design)	-	100	-
5/5.5- Table1(REQUIREMENTS-Thickness)	-	180	-
5/5.6/5.6.1(REQUIREMENTS-Channel)	-	100	-
5/5.7- Table2(REQUIREMENTS- Physical Requirements- as per IS 3400 (Part 1, Part 2, Part 4, Part 9, Part 10, Part 16))	-	4000	-
5/5.3/5.3.1(REQUIREMENTS- Construction)	-	150	-
5/5.1(REQUIREMENTS-General)	-	100	-
5/5.2- Fig. 1 to 5(REQUIREMENTS-Design)	-	100	-
5/5.5- Table1(REQUIREMENTS-Thickness)	-	180	-
5/5.6/5.6.1(REQUIREMENTS-Channel)	-	100	-
5/5.7- Table2(REQUIREMENTS- Physical Requirements- as per IS 3400 (Part 1, Part 2, Part 4, Part 9, Part 10, Part 16))	-	4000	-
5/5.3/5.3.1(REQUIREMENTS- Construction)	-	150	-
5/5.1(REQUIREMENTS-General)	-	100	-
5/5.2- Fig. 1 to 5(REQUIREMENTS-Design)	-	100	-
5/5.5- Table1(REQUIREMENTS-Thickness)	-	180	-
5/5.6/5.6.1(REQUIREMENTS-Channel)	-	100	-
5/5.7- Table2(REQUIREMENTS- Physical Requirements- as per IS 3400 (Part 1, Part 2, Part 4, Part 9, Part 10, Part 16))	-	4000	-
6(Marking and packing)	-	180	-
8.1(Test methods)	-	0	-
8.3(Measurement of thickness)	-	180	-
Cl.6.1,6.2,6.3(Marking and packing)	-	180	-
8.1(Test Methods)	-	0	-
Cl.8.3(Measurement of thickness ")	-	180	-
5.5 (Amendment 1)(Thickness)	-	180	-
5.7 Table 2 i) (Amendment 1)(Relative Density)	-	300	-
5.7, Table 2 ii) (Amendment 1)(Hardness, degree, Shore A)	-	600	-
5.7, Table 2 iv) (Amendment 1)(Abrasion Resistance at applied force of 10 N)	-	1080	-
5.7, Table 2 v) (Amendment 1)(Tensile strength)	-	250	-
5.7, Table 2 vi) (Amendment 1)(Elongation at break)	-	250	-
5.7, Table 2 vii) (Amendment 1)(Tear strength (average force))	-	500	-
5.7, Table 2 iii) (Amendment 1)(Flexing resistance)	-	1080	-

26 Dec, 2027

-
-

7026

ACCURATE TEST SOLUTIONS LLP (F21), NOIDA

8141226

IS 302 : Part 2 : Sec 80 (2017)

Household and similar electrical appliances - Safety: Part 2 - 80 particular requirements for fans (First Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
32.0(Radiation, Toxicity and Similar Hazards)	-	1000	-
31.0(Resistance To Rusting)	-	1000	-
30.0(Resistance To Heat and Fire)	-	1000	-
29.0(Creepage Distances and Clearances)	-	1000	-
28.0(Screws and Connections)	-	1000	-
27.0(Provision For Earthing)	-	1000	-
26.0(Terminals for external conductors)	-	1000	-
25.0(Supply Connection and External Flexible Cords)	-	1000	-
23.0(Internal Wiring)	-	1000	-
22.0(Construction)	-	1000	-
21.0(Mechanical Strength)	-	1000	-
20.0(Stability and mechanical hazards)	-	1000	-
19.0(Abnormal Operation)	-	1000	-
17.0(Overload Protection of transformer and associated circuit)	-	1000	-
16.0(Leakage current and Electric strength (After Humidity (Environmental) Treatment))	-	1000	-
15.0(Moisture resistance)	-	1000	-
14.0(Transient Overvoltage)	-	1000	-
13.0(Leakage Current and electric strength at operating temperature)	-	1000	-
11.0(Heating)	-	1000	-
10.0(Input and Current)	-	1000	-
8.0(Protection against access to live parts)	-	1000	-
7.0(Classification)	-	1000	-
6.0(Marking and Instructions)	-	1000	-
4(GENERAL REQUIREMENT)	-	1000	-
5(GENERAL CONDITIONS FOR THE TESTS)	-	1000	-
24.0(Components)	-	0	-
19.11.4.1(Electrostatic discharges)	-	0	-
19.11.4.2(Radiated fields)	-	0	-
19.11.4.3(Fast transient bursts)	-	0	-
19.11.4.4(Surge immunity test)	-	0	-
19.11.4.5(Immunity to conducted discharges)	-	0	-
19.11.4.6(Class 3 Voltage dips and interruptions)	-	0	-
19.11.4.7(Harmonics)	-	0	-

04 Jul, 2027

-
Included w.e.f.17.03.2025 Exclusion Cl 19.11.4.1 to Cl 19.11.4.7 (EMI/EMC) Cl 24 (Components)

7027

Amit Test and Calibration Centre (8172006)

8172006

IS 9968 : Part 2 (2002)

Specification for elastomer - Insulated cables: Part 2 for working voltages from 3.3 kV up to and including 33 kV (First Revision)

195000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(CONDUCTORS: Cables for Fixed Installation)	-	500	-
4.2(CONDUCTORS:Flexible Cables)	-	500	-
5(INSULATION)	-	500	-
6(SEMICONDUCTING COMPOUND)	-	500	-
7.1(Proofed Tape)	-	500	-
7.2(Polyethylene Terephthalate ( P E T P ) or Polypropylene Base Tape : Thickness)	-	500	-
7.3(Tape )	-	500	-
8(SCREENING)	-	500	-
9(CENTRE AND FILLERS)	-	500	-
10(ARMOUR)	-	500	-
11.1(Inner Sheath)	-	500	-
11.2(Outer Sheath)	-	500	-
12.1(Tapes)	-	500	-
12.2(Cords and Yarns)	-	500	-
13.1 & 13.2(CONSTRUCTION:CONDUCTORS-Cables for Fixed Installations/Flexible Cables)	-	500	-
13.3(Earthing Conductor)	-	500	-
13.3.1(Earthing Conductor)	-	500	-
13.4(Separator Tape)	-	500	-
14(CONDUCTOR SCREENING)	-	500	-
15.1(INSULATION : Application)	-	500	-
15.2(Thickness of Insulation)	-	1000	-
15.3(Tolerance on Thickness of Insulation)	-	1000	-
16.1(INSULATION SCREENING : Application)	-	500	-
16.2(INSULATION SCREENING : Parts )	-	500	-
16.3(INSULATION SCREENING : Non Metallic Parts )	-	500	-
16.4(INSULATION SCREENING : Metallic Parts )	-	500	-
17(CORE IDENTIFICATION)	-	500	-
17(CORE IDENTIFICATION: Unscreed cable )	-	500	-
18.1(LAYING UP OF CORES)	-	500	-
18.2(LAYING UP OF CORES : Flexible cable)	-	500	-
18.3(LAYING UP OF CORES : Binder Tape)	-	500	-
19.1(Inner Sheath : Application)	-	500	-
19.2(Thickness of Inner Sheath)	-	1000	-
19.3(Inner Sheath : proofed tape)	-	500	-
20.1(ARMOURING: Application)	-	500	-
20.2(Type of Armour)	-	500	-
20.2 1.2(Direction of lay of armour)	-	500	-
20.2 1.3(Joint in armour)	-	500	-
20.2.2(Filling Factot )	-	500	-
20.2.2(Diameter of braiding)	-	500	-
20.2.2.1(Braiding material)	-	500	-
20.3(Substitution of the galvanized steel wires/formed)	-	500	-
21.1(OUTER SHEATH)	-	500	-
21.2(Coulor of Outer sheath)	-	500	-
21.3(Thickness of Outer Sheat: Average)	-	1000	-
21.3(Thickness of Outer Sheat: Minimum)	-	1000	-
22.1 a)1)(Annealing test (for copper) - IS 10810: Part 1)	-	1500	-
22.1 a)2)(Tensile test (for aluminium) -IS 10810: Part 2)	-	1500	-
22.1 a)3)(Wrapping Test (for aluminium) - IS 10810: Part 3)	-	1500	-
22.1 a)4)(Conductor resistance test)	-	5000	-
22.1 a)5)(Persulphate test (tinned copper conductor)- IS 10810: Part 4)	-	5000	-
22.1 b)1)(Test for Galvanized Steel Wires/Formed Wires 1) Dimensions -IS 10810: Part 36)	-	1000	-
22.1 b)2)i)(Test for Galvanized Steel Wires/Formed Wires 2) Tensile Strentgh -IS 10810: Part 37)	-	1500	-
22.1 b)2)ii)(Test for Galvanized Steel Wires/Formed Wires 2) Elongation at break -IS 10810: Part 37)	-	1500	-
22.1 b)2)iii)(Test for Galvanized Steel Wires/Formed Wires 3) Torsion (for round wires only) -IS 10810: Part 38)	-	1500	-
22.1 b)2)iv)(Test for Galvanized Steel Wires/Formed Wires 4) Winding (for strips only) -IS 10810: Part 39)	-	1500	-
22.1 b)2)v)(Test for Galvanized Steel Wires/Formed Wires 5) Zinc coating : Uniformity-IS 10810: Part 40)	-	1500	-
22.1 b)2)vi)(Test for Galvanized Steel Wires/Formed Wires 5) Zinc coating : Mass -IS 10810: Part 41)	-	1500	-
22.1 b)2) vii) (Resistivity - IS 10810: Part 42)	-	5000	-
22.1 c)2)(Physical Tests for Insulation : Tensile Strenth - IS 10810: Part 7)	-	2500	-
22.1 c)2)(Physical Tests for Insulation : Elongation - IS 10810: Part 7)	-	2500	-
22.1 c)2)(Physical Tests for Sheath : Tensile Strenth - IS 10810: Part 7)	-	2500	-
22.1 c)2)(Physical Tests for Sheath : Elongation - IS 10810: Part 7)	-	2500	-
22.1 c)3)(Physical Tests for Insulation ( Ageing in air oven): Tensile Strenth - IS 10810: Part 11)	-	5000	-
22.1 c)3)(Physical Tests for Insulation ( Ageing in air oven): Tensile Strenth Variation - IS 10810: Part 12)	-	5000	-
22.1 c)3)(Physical Tests for Insulation( Ageing in air oven) : Elongation - IS 10810: Part 11)	-	5000	-
22.1 c)3)(Physical Tests for Insulation( Ageing in air oven) : Elongation variation - IS 10810: Part 12)	-	5000	-
22.1 c)3)(Physical Tests for Sheath( Ageing in air oven) : Tensile Strenth - IS 10810: Part 11)	-	5000	-
22.1 c)3)(Physical Tests for Sheath( Ageing in air oven) : Tensile Strenth variation - IS 10810: Part 12)	-	5000	-
22.1 c)3)(Physical Tests for Sheath ( Ageing in air oven): Elongation - IS 10810: Part 11)	-	5000	-
22.1 c)3)(Physical Tests for Sheath ( Ageing in air oven): Elongation variation - IS 10810: Part 12)	-	5000	-
22.1 c)4)(Physical Tests for Insulation ( Ageing in air bomb): Tensile Strenth variation - IS 10810: Part 56)	-	5000	-
22.1 c)4)(Physical Tests for Insulation( Ageing in air bomb) : Elongation variation - IS 10810: Part 56)	-	5000	-
22.1 c)4)(Physical Tests for Sheath(Ageing in air bomb) : Tensile Strenth variation - IS 10810: Part 56)	-	5000	-
22.1 c)4)(Physical Tests for Sheath ( Ageing in air bomb): Elongation variation - IS 10810: Part 56)	-	5000	-
22.1 c)5)(Physical Tests for Insulation :Hot set Elongation - IS 10810: Part 30)	-	2500	-
22.1 c)5)(Physical Tests for Insulation :Permanent set - IS 10810: Part 30)	-	2500	-
22.1 c)5)(Physical Tests for Sheath :Hot set Elongation - IS 10810: Part 30)	-	2500	-
22.1 c)5)(Physical Tests for Sheath :Permanent set - IS 10810: Part 30)	-	2500	-
22.1 c)6)(Physical Tests for Sheath(Oil resistance test) : Tensile Strenth Variation - IS 10810: Part 31)	-	5000	-
22.1 c)6)(Physical Tests for Sheath ( Oil resistance test): Elongation Variation - IS 10810: Part 31)	-	5000	-
22.1 c)7)(Tear Resistance test - IS 10810: Part 17)	-	2500	-
22.1 c)8)(Shrinkage : Insulation - IS 10810: Part 12)	-	5000	-
22.1 c)8)(Shrinkage test- Crack observed : Insulation - IS 10810: Part 13)	-	5000	-
22.1 c)8)(Shrinkage test : Sheath - IS 10810: Part 12)	-	2500	-
22.1 c)8)(Shrinkage test - Crack oberved : Sheath - IS 10810: Part 13)	-	2500	-
22.1 c)9)(Hot deformation test : Insulation - IS 10810: Part 15)	-	5000	-
22.1 c)9)(Hot deformation test : Sheath - IS 10810: Part 15)	-	5000	-
22.1 c)10)(Loss of mass in air oven : Insulation - IS 10810: Part 10)	-	5000	-
22.1 c)10)(Loss of mass in air oven : Sheath - IS 10810: Part 10)	-	5000	-
22.1 c)11)(Heat shock : Insulation - IS 10810: Part 14)	-	2500	-
22.1 c)11)(Heat shock : Sheath - IS 10810: Part 14)	-	2500	-
22.1 c)12)(Thermal stability : Insulation - IS 10810: Part 60)	-	1500	-
22.1 c)12)(Thermal stability : Sheath - IS 10810: Part 60)	-	1500	-
22.1 d)(Insulation Resistance Test: Volume resistivity )	-	7000	-
22.1 d)(Insulation Resistance Test: Insulation resistance constant )	-	5000	-
22.1 e)(Partial Discharge Test)	-	45000	-
22.1 f)(Bending Test Followed by Partial Discharge Test)	-	5000	-
22.1 g)(Dielectric Power Factor Test 1) As a function of Voltage)	-	25000	-
22.1 g)(Dielectric Power Factor Test 1) As a function of temperature)	-	30000	-
22.1 h)(Heating Cycle Test)	-	30000	-
22.1 j)(Impulse Withstand Test)	-	35000	-
22.1 k)(High Voltage Test for Four Hours)	-	10000	-
22.1 m)(Water Absorption Test - IS 10810: Part 28)	-	7000	-
22.1 n)(Flammability)	-	2500	-
24.1(Manufacturer's Identification)	-	500	-
24.2(Voltage Identification)	-	500	-
24.3(Cable Code)	-	500	-
25.2.1(Marking on drum )	-	500	-
25.2.2(BIS Certification Marking)	-	500	-
22.4 (a)(Ozone Resistance Test)	-	5000	-
22.4 (b)(Cold impacts test for PVC sheath)	-	2500	-
7.1(Proofed Tape: Thickness)	-	1000	-

16 Apr, 2029

-
Included w.e.f.17.03.2025

7028

VARDAN ENVIROLAB, GURUGRAM

8169616

IS 6719 (1972)

Solid Pvc Soles And Heels

3500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.6.1(Hardness )	-	600	-
3.6 (vi)(Lead (as Pb) ppm)	-	990	-
3.6 (v)(Volatility, percent by means )	-	800	-
3.6 (iv)(Tear Strength a) Force Part b) Back Part )	-	500	-
3.6 (iii)(Elongation at break, percent )	-	500	-
3.6 (ii)(Tensile Strength )	-	500	-
3.6 (i)(Relative density )	-	300	-
Cl. 3.1,3.2,3.3,3.4,3.5(Material)	-	150	-
6 ,6.1,6.2,6.3(Test Method)	-	0	-
Cl. 3.1,3.2,3.3,3.4,3.5(Material)	-	150	-
Cl. 6.4(Measurement of thickness)	-	500	-
Table 1 (Flexing resistance)(Table 1 (Flexing resistance, Bennewart method, cut growth at the end of 30 000 cycles, mm, Max))	-	1000	-
Table 1 (Abrasion resistance)(Abrasion resistance at applied force of 10 N (volume loss), mm3, Max)	-	1080	-
Table 1 Cl. 3.6, Sl No (iii)(Volatility, Percent by mass)	-	800	-
Table 1 Cl. 3.6, Sl No (iv)("Lead (as Pb), Shoes for infants, children and boys and girls, ppm")	-	990	-
Table 1 Cl. 3.6, Sl No (iv)("Lead (as Pb), for other sized shoes, ppm ")	-	990	-

26 Dec, 2027

-
-

7029

Bharat Test House Pvt. Ltd. 1668 Sonipat

9168306

IS 9567 (2001)

Tin or tin - Lead coated copper wire - Specificaiton (First Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.3(Details of Coating)	-	5000	-
4.4(Diameter of Coated Wire)	-	3000	-
5(Packing and Marking)	-	500	-
6.4.1(Measurement of Diameter)	-	500	-
6.4.2(Elongation and Breaking Strength Test)	-	2000	-
6.4.3(Bend Test)	-	1000	-
6.4.4(Solderability Test)	-	1000	-
6.4.5(Continuity of Coating Test)	-	1000	-
6.4.6(Adherence of Coating Test)	-	1000	-
4.1(Material)	-	2000	-
4.2(Resistivity)	-	0	-
6.3.1(Resistance Test)	-	0	-
4.3(Details of Coating)	-	100	-
4.4(Diameter of Coated Wire)	-	100	-
5(Packing and Marking)	-	100	-
6.4.1(Measurement of Diameter)	-	100	-
6.4.2(Elongation and Breaking Strength Test)	-	1000	-
6.4.3(Bend Test)	-	1000	-
6.4.4(Solderability Test)	-	1000	-
6.4.5(Continuity of Coating Test)	-	1000	-
6.4.6(Adherence of Coating Test)	-	1000	-
4.1(Material)	-	0	-
4.2(Resistivity)	-	0	-
6.3.1(Resistance Test)	-	0	-
4.3(Details of Coating)	-	0	-
4.4(Diameter of Coated Wire)	-	0	-
5(Packing and Marking)	-	0	-
6.4.1(Measurement of Diameter)	-	0	-
6.4.2(Elongation and Breaking Strength Test)	-	0	-
6.4.3(Bend Test)	-	0	-
6.4.4(Solderability Test)	-	0	-
6.4.5(Continuity of Coating Test)	-	0	-
6.4.6(Adherence of Coating Test)	-	0	-
4.1(Material)	-	0	-
4.2(Resistivity)	-	0	-
6.3.1(Resistance Test)	-	0	-

-
Included w.e.f.13.05.2025 Exclusion Cl 4.2 (Resistivity) Cl 6.3.1 (Resistance Test)

7030

DELHI TEST HOUSE (50) KUNDLI SONIPAT

9127026

IS/IEC 61683 (1999)

Photovoltaic systems - Power conditioners - Procedure for measuring efficiency

111000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Efficiency calculations)	-	25000	-
6(Efficiency test circuits)	-	25000	-
7(Loss measurement)	-	25000	-
Annex A(Power conditioner description)	-	1000	-
Annex B(Power efficiency and conversion factor)	-	2500	-
Annex C(Weighted average energy efficiency)	-	2500	-
Annex D(Derivation of efficiency tolerance in Table 2)	-	1000	-
4(Efficiency measurement conditions)	-	25000	-
4.1(DC power source for testing)	-	500	-
4.2(Temperature)	-	500	-
4.3(Output voltage and frequency)	-	500	-
4.4(Input voltage)	-	500	-
4.5(Ripple and distortion)	-	500	-
4.6(Resistive loads/utility grid)	-	500	-
4.7(Reactive loads)	-	500	-
4.8(Resistive plus non-linear loads)	-	250	-
4.9(Complex loads)	-	250	-

23 Jun, 2028

-
Included w.e.f.07.03.2025

7031

Planet Electro Labs Private Limited, Wazirpur

8185226

IS 302 : Part 2 : Sec 9 (2009)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 9 toasters, grills, roasters and similar appliances (First Revision)

45000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 6 IS 302-2-9(Classification- IS 302-1)	-	1000	-
Cl. 7 IS 302-2-9(Marking and Instruction)	-	1000	-
Cl. 8 IS 302-2-9(Protection against access to live parts)	-	1000	-
Cl. 9 IS 302-2-9(Starting of motor operated appliances)	-	1	-
Cl. 10 IS 302-2-9(Power Input and Current )	-	1000	-
Cl. 11 IS 302-2-9(Heating)	-	1000	-
Cl. 13.3 IS 302-2-9(Leakage Current & Electric Strength at Operating Temperature)	-	1000	-
Cl. 14 IS 302-2-9(Transient overvoltage)	-	1000	-
Cl. 15 IS 302-2-9(Moisture Resistance)	-	1000	-
Cl. 16 IS 302-2-9(Leakage Current and Electric strength )	-	1000	-
Cl. 17 IS 302-2-9(Overload protection of transformers and associated circuits.)	-	1000	-
Cl. 18 IS 302-2-9(Endurance)	-	1000	-
Cl. 19 IS 302-2-9(Abnormal Operation )	-	1000	-
Cl. 20 IS 302-2-9(Stability and mechanical Hazards)	-	1000	-
Cl. 21 IS 302-2-9(Mechanical Strength)	-	1000	-
Cl. 22 IS 302-2-9(Construction )	-	1000	-
Cl. 23 IS 302-2-9(Internal Wiring)	-	1000	-
Cl. 24 IS 302-2-9(Components)	-	1000	-
Cl. 25 IS 302-2-9(Supply Connections and External Flexible Cables and Cords )	-	1000	-
Cl. 26 IS 302-2-9(Terminal For External Conductors )	-	1000	-
Cl. 27 IS 302-2-9(Provision For Earthing )	-	1000	-
Cl. 28 IS 302-2-9(Screws and Connections)	-	1000	-
Cl. 29 IS 302-2-9(Creepage Distances, Clearances And Distances Through Insulation)	-	1000	-
Cl. 30 IS 302-2-9(Resistance To Heat, Fire And Tracking)	-	1000	-
Cl. 31 IS 302-2-9(Resistance To Rusting )	-	1000	-
Cl. 32 IS 302-2-9(Radiation, Toxicity and similar hazards)	-	1000	-
Cl.32(Verification)	-	1000	-
Cl.31(Verification)	-	1	-
Cl.30(Verification)	-	1	-
CL.29(Verification)	-	1	-
Cl.28(Verification)	-	1	-
Cl.27(Verification)	-	1	-
Cl.26(Verification)	-	1	-
Cl.25(Verification)	-	1	-
Cl.24(Verification)	-	1	-
Cl.23(Verification)	-	1	-
Cl.22(Verification)	-	1	-
Cl.20(Verification)	-	1	-
Cl.10(Verification)	-	1	-
Cl.21(Verification)	-	1	-
Cl.19(Verification)	-	1	-
Cl.13(Verification)	-	1	-
Cl.14(Verification)	-	1	-
Cl.15.1(Moisture Resistance)	-	1	-
Cl. 16(Verification)	-	1	-
Cl. 6(Classification- IS 302-1)	-	1	-
Cl.8(Verification)	-	1	-
32(Radiation, toxicity and similar hazards)	-	1	-
31(Resistance to rusting)	-	1	-
31(Resistance to rusting)	-	1000	-
30.2.4(Resistance to heat and fire)	-	1000	-
30.2(Resistance to heat and fire)	-	1000	-
30.1(Resistance to heat and fire)	-	1000	-
29.3(Clearances, creepage distances and solid insulation)	-	1	-
29.2(Clearances, creepage distances and solid insulation)	-	1	-
29.2(Clearances, creepage distances and solid insulation)	-	1	-
29.1, Table No.- 16, Table No.- 17 & Table No.18(Clearances, creepage distances and solid insulation)	-	1	-
29.1, Table No.- 16, Table No.- 17 & Table No.18(Clearances, creepage distances and solid insulation)	-	1	-
28.2 to 28.4(Screws and connections)	-	1	-
28.1, Table No.-14(Screws and connections)	-	2000	-
27.6(Provision for earthing)	-	1	-
27.5(Provision for earthing)	-	1	-
27.1 to 27.4(Provision for earthing)	-	1	-
26.10 & 26.11(Terminals for external conductors)	-	1000	-
26.9(Terminals for external conductors)	-	1	-
26.1 to 26.8(Terminals for external conductors)	-	2000	-
25.16 to 25.25(Supply connection and external flexible cords)	-	2000	-
25.15(Supply connection and external flexible cords)	-	1	-
25.14(Supply connection and external flexible cords)	-	1	1
25.14(Supply connection and external flexible cords)	-	1	-
25.9 to 25.13(Supply connection and external flexible cords)	-	1	-
25.8, Table No.-11(Supply connection and external flexible cords)	-	1	-
25.5 to 25.7(Supply connection and external flexible cords)	-	1	-
25.4(Supply connection and external flexible cords)	-	1	-
25.3(Supply connection and external flexible cords)	-	1	1
25.2(Supply connection and external flexible cords)	-	1	-
25.1(Supply connection and external flexible cords)	-	1	-
24.101(Components)	-	1	-
23.3(Internal wiring)	-	1	-
23.4(Internal wiring)	-	1	-
23.5(Internal wiring)	-	1000	-
22.108(Constructions)	-	1	-
22.101 to 22.107(Constructions)	-	2000	-
22.13 to 22.48(Constructions)	-	1	1
22.12(Constructions)	-	1	-
22.11(Constructions)	-	1	-
22.11(Constructions)	-	1	-
22.7 to 22.10(Constructions)	-	1	-
22.6(Constructions)	-	1	-
22.5(Constructions)	-	1	-
22.4(Constructions)	-	1	-
22.3(Constructions)	-	1	1
22.2(Constructions)	-	1	-
22.1(Constructions)	-	1	-
21.101(MECHANICAL STRENGTH)	-	2000	-
21.101(MECHANICAL STRENGTH)	-	1	-
21.2(MECHANICAL STRENGTH)	-	1	-
21.1(MECHANICAL STRENGTH)	-	1	-
20.2(Stability and mechanical hazards)	-	1	-
20.1(Stability and mechanical hazards)	-	1	-
19.104(ABNORMAL OPERATION)	-	1	-
19.103(ABNORMAL OPERATION)	-	1	-
19.102(ABNORMAL OPERATION)	-	2000	-
19.101(ABNORMAL OPERATION)	-	2000	-
19.1 to 19.13, Table No. - 9(ABNORMAL OPERATION)	-	2000	-
17(Overload protection of transformers and associated circuits)	-	1	-
16.3(Insulation resistance test)	-	1	-
16.3(Electric strength test)	-	1000	-
16.1 & 16.2(Leakage current test)	-	1	-
15.3(Moisture resistance)	-	1000	-
15.3(Moisture resistance)	-	1	-
15.3(Moisture resistance)	-	1000	-
15.2(Moisture resistance)	-	1	-
15.2(Moisture resistance)	-	1	-
15.2(Moisture resistance)	-	1	-
15.2(Moisture resistance)	-	1	-
15.1(Moisture resistance)	-	1	-
14, Table No.- 6 & Table No.-16(Transient over voltages)	-	1	-
13.3 and Table No.- 4(Electric strength test)	-	1	-
13.1, 13.2(Leakage current test)	-	1	-
13.1, 13.2(Leakage current test)	-	1	-
11.101(Heating)	-	1	-
11.1 to 11.8, Table No.-3(Heating)	-	1	-
10.1 & 10.2 -Table No. 1, Table No. 2(Power Input and Current)	-	1	-
8.1.5(Protection against access to live parts)	-	1000	-
8.1.4(Protection against access to live parts)	-	1	-
8.1.3(Protection against access to live parts)	-	1	-
8.1.2(Protection against access to live parts)	-	1	-
8.1, 8.1.1 & 8.2(Protection against access to live parts)	-	1	-
7.14(Legibility & Durability of Markings test)	-	1	-
7.1 to 7.13, 7.15, 7.16(Marking)	-	1	-
32(Radiation, toxicity and similar hazards)	-	1	-
31(Resistance to rusting)	-	1	-
31(Resistance to rusting)	-	1	-
30.2.4(Resistance to heat and fire)	-	1	-
30.2(Resistance to heat and fire)	-	1	-
30.1(Resistance to heat and fire)	-	1	-
29.2(Clearances, creepage distances and solid insulation)	-	1	-
29.2(Clearances, creepage distances and solid insulation)	-	1000	-
29.1, Table No.- 16, Table No.- 17 & Table No.18(Clearances, creepage distances and solid insulation)	-	1	-
29.1, Table No.- 16, Table No.- 17 & Table No.18(Clearances, creepage distances and solid insulation)	-	1	-
28.2 to 28.4(Screws and connections)	-	1	-
28.1, Table No.-14(Screws and connections)	-	1	-
27.6(Provision for earthing)	-	1	-
27.5(Provision for earthing)	-	1	-
27.1 to 27.4(Provision for earthing)	-	1	-
26.10 & 26.11(Terminals for external conductors)	-	1	-
26.9(Terminals for external conductors)	-	1	-
26.1 to 26.8(Terminals for external conductors)	-	1000	-
25.16 to 25.25(Supply connection and external flexible cords)	-	1	-
25.15(Supply connection and external flexible cords)	-	1	-
25.14(Supply connection and external flexible cords)	-	1	-
25.14(Supply connection and external flexible cords)	-	1	-
25.9 to 25.13(Supply connection and external flexible cords)	-	1	-
25.8, Table No.-11(Supply connection and external flexible cords)	-	1	-
25.5 to 25.7(Supply connection and external flexible cords)	-	1	-
25.4(Supply connection and external flexible cords)	-	1	-
25.3(Supply connection and external flexible cords)	-	1	-
25.2(Supply connection and external flexible cords)	-	1	-
25.1(Supply connection and external flexible cords)	-	1	-
24.101(Components)	-	1	-
24.101(Components)	-	1	-
24.2 to 24.6(Components)	-	1	-
24.1(Components)	-	1	-
23.5(Internal wiring)	-	1	-
23.4(Internal wiring)	-	1	-
23.3(Internal wiring)	-	1	-
23.1 & 23.2(Internal wiring)	-	1	-
22.111(Constructions)	-	1	-
22.111(Constructions)	-	1	-
22.11o(Constructions)	-	1	-
22.109(Constructions)	-	1	1
22.108(Constructions)	-	1	-
22.101 to 22.107(Constructions)	-	1	-
22.13 to 22.48(Constructions)	-	1	-
22.12(Constructions)	-	1	-
22.11(Constructions)	-	1	-
22.11(Constructions)	-	1	-
22.7 to 22.10(Constructions)	-	1	-
22.6(Constructions)	-	1	-
22.5(Constructions)	-	1	-
22.4(Constructions)	-	1	-
22.3(Constructions)	-	1	-
22.2(Constructions)	-	1	-
22.1(Constructions)	-	1	-
21.101(MECHANICAL STRENGTH)	-	1	-
21.101(MECHANICAL STRENGTH)	-	1	-
21.2(MECHANICAL STRENGTH)	-	1	-
21.1(MECHANICAL STRENGTH)	-	1	-
20.2(Stability and mechanical hazards)	-	1	-
20.1(Stability and mechanical hazards)	-	1	-
19.104(ABNORMAL OPERATION)	-	1	-
19.103(ABNORMAL OPERATION)	-	1	-
19.102(ABNORMAL OPERATION)	-	1	-
19.101(ABNORMAL OPERATION)	-	1	-
19.1 to 19.13, Table No. - 9(ABNORMAL OPERATION)	-	1	-
17(Overload protection of transformers and associated circuits)	-	1	-
16.3(Insulation resistance test)	-	1	-
16.3(Electric strength test)	-	1	-
16.1 & 16.2(Leakage current test)	-	1	-
15.3(Moisture resistance)	-	1	-
15.3(Moisture resistance)	-	1	-
15.3(Moisture resistance)	-	1	-
15.2(Moisture resistance)	-	1	-
15.2(Moisture resistance)	-	1	-
15.2(Moisture resistance)	-	1	-
15.2(Moisture resistance)	-	1	-
15.1(Moisture resistance)	-	1	1
14, Table No.- 6 & Table No.-16(Transient over voltages)	-	1	-
13.3 and Table No.- 4(Electric strength test)	-	1	-
13.1, 13.2(Leakage current test)	-	1	-
13.1, 13.2(Leakage current test)	-	1	-
11.101(Heating)	-	1	-
11.1 to 11.8, Table No.-3(Heating)	-	1	-
10.1 & 10.2 -Table No. 1, Table No. 2(Power Input and Current)	-	1	-
8.1.5(Protection against access to live parts)	-	1	1
8.1.4(Protection against access to live parts)	-	1	-
8.1.3(Protection against access to live parts)	-	1	-
8.1.2(Protection against access to live parts)	-	1	-
8.1, 8.1.1 & 8.2(Protection against access to live parts)	-	1	-
7.14(Legibility & Durability of Markings test)	-	1	-
7.1 to 7.13, 7.15, 7.16(Marking)	-	1	-
32(Radiation ,Toxicity and similar hazards)	-	1	-
31(Resistance to Rusting)	-	1	-
30(Resistance to Heat & Fire)	-	1	-
29(Clearances, Creepage Distances & Solid Insulation)	-	1	-
28(Screws & Connections)	-	1	-
27(Provision For Earthing)	-	1	-
26(Terminals For External Conductors)	-	1	-
25(Supply Connection & External Flexible Cords)	-	1	-
23(Internal wiring)	-	1	-
24(Components)	-	1	-
22(Construction)	-	1	-
21(Mechanical strength)	-	1	-
20(Stability & Mechanical Hazards)	-	1	-
19(Abnormal Operation)	-	1	-
17(Overload Protection/ Overload Protection of Transformers & Associated Circuits)	-	1	-
16(Leakage Current and Electric Strength)	-	1	-
15(Moisture Resistance)	-	1	-
14(Transient Over Voltage)	-	1	-
13(Leakage Current and Electric Strength at Operating Temperature)	-	1	-
11(Temperature Rise/ Heating)	-	1	-
10(Power Input & Current)	-	1	-
9(Starting Of Motor Operated Appliances)	-	1	-
8(Protection against access to live parts)	-	1	-
32(Radiation ,Toxicity and similar hazards)	-	1	-
31(Resistance to Rusting)	-	1	-
30(Resistance to Heat & Fire)	-	1	-
29(Clearances, Creepage Distances & Solid Insulation)	-	1	-
28(Screws & Connections)	-	1	-
27(Provision For Earthing)	-	1	-
26(Terminals For External Conductors)	-	1	-
25(Supply Connection & External Flexible Cords)	-	1	-
24(Components)	-	1	-
23(Internal wiring)	-	1	-
22(Construction)	-	1	-
21(Mechanical strength)	-	1	-
20(Stability & Mechanical Hazards)	-	1	-
19(Abnormal Operation)	-	1	-
17(Overload Protection/ Overload Protection of Transformers & Associated Circuits)	-	1	-
16(Leakage Current and Electric Strength)	-	1	-
15(Moisture Resistance)	-	1	-
14(Transient Over Voltage)	-	1	-
13(Leakage Current and Electric Strength at Operating Temperature)	-	1	-
11(Temperature Rise/ Heating)	-	1	-
10(Power Input & Current)	-	1	-
9(Starting Of Motor Operated Appliances)	-	1	-
8(Protection against access to live parts)	-	1	-
19.11.4.1(Electrostatic discharges)	-	1	-
19.11.4.2(Radiated fields)	-	1	-
19.11.4.3(Fast transient bursts)	-	1	-
19.11.4.4(Surge immunity test)	-	1	-
19.11.4.5(Immunity to conducted discharges)	-	1	-
19.11.4.6(Class 3 Voltage dips and interruptions)	-	1	-
19.11.4.7(Harmonics)	-	1	1
Cl.11(Verification)	-	1	-
24.101(Components)	-	1	-
24.2 to 24.6(Components)	-	1	-
24.1(Components)	-	1	-
23.6 to 23.10(Internal wiring)	-	1	-
23.1 & 23.2(Internal wiring)	-	1	-
22.111(Constructions)	-	1	-
22.111(Constructions)	-	1	-
22.11o(Constructions)	-	1	-
22.109(Constructions)	-	1	-
29.3(Clearances, creepage distances and solid insulation)	-	1	-
23.6 to 23.10(Internal wiring)	-	1	-
Cl. 7(Verification)	-	1	-

08 May, 2028

-
19.11.4.1 To 19.11.4.7

7032

BCH Electric Limited, Faridabad

8186026

IS/IEC 60529 (2001)

Degrees of protection provided by enclosures (IP Code)

Motor starter Starter, Enclosure

170000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5(Degrees of protection against access to hazardous parts and against solid foreign objects indicated by the first characteristic numeral)	-	20000	Only for internal testing
Cl-5.1(Protection against access to hazardous parts)	-	20000	Only for internal testing
Cl-5.2(Protection against solid foreign objects)	-	25000	Only for internal testing
Cl-6(Degrees of protectlon against ingress of water indicated 'by the second characteristic numeral)	-	25000	Only for internal testing
Cl-7(Degrees of protection against access to hazardous parts indicated by the additional letter)	-	25000	Only for internal testing
Cl-8(Supplementary letter)	-	25000	Only for internal testing
Cl-10(Marking)	-	20000	Only for internal testing

05 Jun, 2028

-
-

7033

Planet Electro Labs Private Limited, Wazirpur

8185226

IS 302 : Part 1 (2024)

Household and Similar Electrical Appliances â Safety Part 1 General Requirements (Seventh Revision)

65000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
12(Charging of metal-ion batteries)	-	0	-
6(Classification- IS 302-1)	-	1000	-
5(General conditions for the tests)	-	1000	-
19.11.4.7(Harmonics)	-	0	-
19.11.4.6(Class 3 Voltage dips and interruptions)	-	0	-
19.11.4.5(Immunity to conducted discharges)	-	0	-
19.11.4.4(Surge immunity test)	-	0	-
19.11.4.3(Fast transient bursts)	-	0	-
19.11.4.2(Radiated fields)	-	0	-
19.11.4.1(Electrostatic discharges)	-	0	-
11.8(Temperature rise)	-	1000	-
11.7(Duration corresponding)	-	1000	-
11.6(Combined appliances)	-	1000	-
11.5(Motor-operated appliances)	-	1000	-
11.4(Heating appliances)	-	1000	-
8.1.5(Live parts of built-in appliances)	-	1000	-
18(Endurance)	-	2000	-
17(Overload protection of transformers and associated circuits)	-	2000	-
16(Leakage current and electric strength)	-	1000	-
4(General requirement)	-	1000	-
32.1(Radiation Toxicity and Similar Hazards)	-	1000	-
31(Resistance to Rusting)	-	1000	-
30.2(Needle Flame Test)	-	1000	-
30.2(Glow Wire Test)	-	1000	-
30.1(Ball pressure test)	-	1000	-
29(clearance, creepage distances and solid insulation)	-	1000	-
28(Screw test and connections)	-	1000	-
27.1(Provision for Earthing, IS 302-1)	-	1000	-
26(Terminals for external conductors)	-	1000	-
25.8(Supply Connection and External Flexible Cords, IS 302-1)	-	1000	-
24(Components)	-	1000	-
23.1(Internal Wiring, IS 302-1)	-	1000	-
22.1(Construction, IS 302-1)	-	2000	-
21.1(Mechanical Strength, IS 302-1)	-	2000	-
20.1(Stability & Mechanical Hazards, IS 302-1)	-	2000	-
19(Abnormal Operation)	-	1000	-
18(Endurance)	-	1000	-
17(Over Load Protection of Transformers and associated circuits)	-	1000	-
16.3(Electric Strength (after clause 15 and 16.2))	-	1000	-
16.2(Leakage Current (after Clause 15))	-	1000	-
16.1(General)	-	1000	-
16.0(General)	-	500	-
15.3(Humidity Test)	-	2000	-
15.2(Spillage Test)	-	1000	-
15.1(Ingress Protection test other than IPX0 (IP test))	-	2000	-
15.0(Moisture resistance)	-	2000	-
14(Transient Over Voltages)	-	1000	-
13.3(Electric Strength at operating temperature)	-	1000	-
13.2(Leakage current at operating temperature)	-	1000	-
13(Leakage current and electric strength at operating temperature)	-	0	-
11.3(Heating)	-	1000	-
11.2(General)	-	0	-
11.1(General)	-	0	-
10.2(Current input)	-	500	-
10.1(Power input)	-	500	-
9(Starting of motor operation test requirements and tests)	-	500	-
8.1.4(Protection against live parts against protective impedance)	-	1000	-
8.1.3(Protection against live parts in visible glowing heating elements)	-	0	-
8.1.2(Protection against live parts in openings)	-	500	-
8.1.1(Protection against live parts in all positions)	-	500	-
7(Marking and instructions)	-	1000	-
A.2(Earth continuity test)	-	0	-
Annex C(Ageing test on motors)	-	0	-
Annex D(Thermal motor protectors)	-	0	-
15.2(Moisture resistance)	-	1000	-
19.17(Abnormal Operation, IS 302-1)	-	1000	-
20.2(Stability & Mechanical Hazards, IS 302-1)	-	1000	-
21.2(Mechanical Strength, IS 302-1)	-	1000	-
21.3(Mechanical Strength, IS 302-1)	-	0	-
22.5(Construction)	-	1000	-
22.6(Construction, IS 302-1)	-	0	-
22.11(Construction, IS 302-1)	-	0	-
22.16(Construction)	-	0	-
22.32(Construction, IS 302-1)	-	0	-
22.42(Construction)	-	0	-
23.3(Internal Wiring, IS 302-1)	-	1000	-
25.6(Supply connection and external flexible cords, IS 302-1)	-	1000	-
25.7(Supply Connection and External Flexible Cords, IS 302-1)	-	0	-
25.14(Supply Connection and External Flexible Cords, IS 302-1)	-	0	-
25.15(Supply Connection and External Flexible Cords, IS 302-1)	-	0	-
26.5(Terminals for external conductors)	-	1000	-
27.5(Provision for Earthing, IS 302-1)	-	1000	-
28.1(Screws and connections)	-	1000	-
22.2(Construction, IS 302-1)	-	1000	-
22.3(Construction, IS 302-1)	-	0	-
B.22.4(Construction, IS 302-1)	-	0	-
B.22.5(Construction, IS 302-1)	-	0	-

08 May, 2028

-
19.11.4.1 to 19.11.4.7 "Domestic Electric Clothes Washing Machines (For testing charges please refer part 2 standard in LIMS)"

7034

ALPHA TEST HOUSE PVT LTD, BAHADURGARH

8185306

IS 17509 (2021)

Disposable Baby Diaper Specification

22000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause no. 3(Material)	-	22000	-
Clause no. 3.1(Top Cover / Top Sheet)	-	500	-
Clause no. 3.2(Absorbent Core)	-	500	-
Clause no. 3.3(Outer Protective Barrier or Back Sheet)	-	500	-
Clause no. 4(Fastening & Securing Mechanism)	-	500	-
Clause no. 5(ManufactureWorkmanship and Finish)	-	500	-
Clause no.6(Type and Size: FOR X LARGE)	-	500	-
Clause no.6(Diaper Length)	-	500	-
Clause no.6(Diaper Width)	-	500	-
Clause no.6(Diaper Crotch)	-	500	-
Clause no.6(Absorbent Core Length)	-	500	-
Clause no.6(Absorbent Core Width Back)	-	500	-
1()	-	500	-
Clause no.6(Absorbent Core Length)	-	500	-
Clause no.6(Absorbent Core Width Front)	-	500	-
Clause no.6(Core Cortch)	-	500	-
Clause no.7(Performance Requirements)	-	500	-
Clause no.7.1(pH Value)	-	500	-
Clause no.7.2 Table-2(Minimum absorption Capacity (X Large))	-	1000	-
Clause no.7.2 Table-2(Rewet under Load (All Sizes))	-	1000	-
Clause no.7.2 Table-2(Rate of Absorption (All Sizes))	-	500	-
Clause no.7.3(Hygiene Testing Requirement, Total Viable Count)	-	4500	-
Clause no.7.3(Hygiene Testing Requirement, Staphylococcus Aureus)	-	2500	-
Clause no.7.4(Biocompatibility Evaluation- Cytotoxicity)	-	0	-
Clause no. 7.4(Biocompatibility Evaluation- Irritation)	-	0	-
Clause no.7.4(Biocompatibility Evaluation- Skin Sensitization)	-	0	-
Clause no.7.5(Phthalate Test)	-	5000	-
Clause no.7.6(Biodegradability and Compostability (optional))	-	0	-
Clause no.7.7(Anti-Bacterial Activity Value (optional))	-	5000	-
9 & 9.1(Marking)	-	0	-
10(Packing)	-	0	-
CL 7.3(Total Viable Count)	-	0	-
CL 7.3(Staphylococcus aureus)	-	2500	-
CL 7.4(Biocompatibility Evaluation - Cytotoxicity, Irritation and Skin Sensitization)	-	0	-
CL 7.6(Biodegradability and Compostability (Optional))	-	0	-
CL 7.7(Anti-Bacterial Activity Value (Optional))	-	5000	-

08 May, 2028

-
Exclusions -CL 7.4 (Biocompatibility Evaluation - Cytotoxicity, Irritation and Skin Sensitization), CL 7.6 (Biodegradability and Compostability (Optional))

7035

ALPHA TEST HOUSE PVT LTD, BAHADURGARH

8185306

IS 17262 (2022)

Textiles - Polyester partially oriented yarn (POY) - Specification (first revision)

45800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2(Identification and Description, Annex J of IS 16481 & IS 667)	-	7500	-
6.1 & 8.2 - Table -3, Sl no. 1(Nominal linear density, denier, IS 7703 (Part 1))	-	2500	-
6.1 & 8.2 - Table -3, Sl no. 2(Cross section)	-	2000	-
6.1 & 8.2 - Table -3, Sl no. 3(No. of filaments)	-	2000	-
6.1 & 8.2 - Table -3, Sl no. 4(Declared average tenacity, gpd, IS 7703 (Part 2))	-	2500	-
6.1 & 8.2 - Table -3, Sl no. 5(Declared elongation, percent, IS 7703 (Part 2))	-	2500	-
6.1 & 8.2 - Table -3, Sl no. 6(Interlace as nips per metre, Annex B)	-	2500	-
6.1 & 8.2 - Table -3, Sl no. 7(Unevenness of linear density, IS 7703 (Part 5))	-	10500	-
6.2- Table -4, Sl no. 1(Moisture regain, percent, Annex C)	-	2000	-
6.2- Table -4, Sl no. 2(Isophthalic acid (IPA) content in Virgin polyester yarn, Percent, Annex C of IS 16481)	-	2500	-
6.2- Table -4, Sl no. 2(Isophthalic acid (IPA) content in Dope dyed/white yarn, Percent, Annex C of IS 16482)	-	2500	-
6.2- Table -4, Sl no. 2(Isophthalic acid (IPA) content in Recycled polyester yarn, Percent, Annex C of IS 16483)	-	2500	-
6.2- Table -4, Sl no. 3(Water soluble matter, Percent, IS 3456)	-	2500	-
6.2- Table -4, Sl no. 4(Finish oil pick-up, percent, Annex D)	-	2500	-
6.2- Table -4, Sl no. 5(Phosphorus content, percent, Annex E)	-	2500	-
6.2- Table -4, Sl no. 6(Ultraviolet resistance, 500 h Percent retained strength, IS 13162 (Part 2))	-	50000	-
6.2- Table -4, Sl no. 7(Anti-microbial activity value, IS/ISO 20743)	-	35000	-
6.2- Table -4, Sl no. 8(Colour strength with reference to standard yarn, Percent, Annex F)	-	2500	-
6.2- Table -4, Sl no. 9(Colour difference with reference to standard yarn, measured as ΔE, Annex F)	-	2500	-
6.3(Freedom from Yarn Defects)	-	3500	-
6.4(Lustre/Brightness)	-	4500	-
6.5- Table -6, Sl no. 1(Light, Change in colour, IS/ISO 105-B01 or IS/ISO 105-B02)	-	7500	-
6.5- Table -6, Sl no. 2(Washing,IS/ISO 105-C10)	-	3500	-
6.5- Table -6, Sl no. 3(Rubbing, IS/ISO 105-X12)	-	3500	-
6.5- Table -6, Sl no. 4(Perspiration (acidic and alkaline), IS/ISO 105-E04)	-	3500	-
6.7- Table -7, Sl no. 1("Free and releasable formaldehyde, mg/kg (ppm),IS 14563 (Part 1) and IS 14563 (Part 2)")	-	9500	-
6.7- Table -7, Sl no. 2(Extractable heavy metals by artificial Acidic sweat/saliva, ppm, Annex A of IS 15651)	-	1000	-
6.7- Table -7, Sl no. 2(Mercury,ppm,Annex A of IS 15651)	-	1000	-
6.7- Table -7, Sl no. 2(Chromium III,ppm,Annex A of IS 15651)	-	1000	-
6.7- Table -7, Sl no. 2(Chromium VI,ppm,Annex A of IS 15651)	-	1000	-
6.7- Table -7, Sl no. 2(Lead,ppm,Annex A of IS 15651)	-	1000	-
6.7- Table -7, Sl no. 2(Cadmium,ppm,Annex A of IS 15651)	-	1000	-
6.7- Table -7, Sl no. 2(Copper,ppm,Annex A of IS 15651)	-	1000	-
6.7- Table -7, Sl no. 2(Antimony,ppm,Annex A of IS 15651)	-	1000	-
6.7- Table -7, Sl no. 3(Pentachlorophenol, ppm, Annex B of IS 15651)	-	1000	-
6.7- Table -7, Sl no. 4(Pesticides (Sum parameter), ppm, Annex D of IS 15651)	-	1000	-
6.7- Table -7, Sl no. 5(Banned Pesticides, ppm, Annex D of IS 15651)	-	1000	-
6.7- Table -7, Sl no. 6("Banned azo colourants (arylamines), mg/kg (ppm), IS 15570")	-	1000	-
6.1 & 8.2 - Table -3, Sl no. 7 (a)(All deniers except microdeniers)	-	1000	-
6.1 & 8.2 - Table -3, Sl no. 7 (b)(Microdeniers)	-	1000	-
6.1 & 8.2 - Table -3, Sl no. 7 ©(Dope dyed (all deniers))	-	1000	-
6.3(Freedom from Yarn Defects)	-	1000	-
6.4(Lustre/Brightness)	-	1000	-
6.5(Colour Fastness Properties of Dyed POY)	-	1000	-
6.1 Table -3, Sl no. 1(Nominal linear density, denier, IS 7703 (Part 1))	-	1000	-
6.1 Table -3, Sl no. 2(Cross section)	-	1000	-
6.1 & 8.2 - Table -3, Sl no. 1(Nominal linear density, denier, IS 7703 (Part 1))	-	1000	-
6.1 & 8.2 - Table -3, Sl no. 2(Cross section)	-	1000	-
6.1 & 8.2 - Table -3, Sl no. 2(Cross section)	-	1000	-
6.1 & 8.2 - Table -3, Sl no. 3(No. of filaments)	-	1000	-
6.1 & 8.2 - Table -3, Sl no. 4(Declared average tenacity, gpd, IS 7703 (Part 2))	-	1000	-
6.1 & 8.2 - Table -3, Sl no. 5(Declared elongation, percent, IS 7703 (Part 2))	-	1000	-
6.1 & 8.2 - Table -3, Sl no. 6(Interlace as nips per metre, Annex B)	-	1000	-
6.5- Table -6, Sl no. 2 (a)(Washing, Change in colour IS/ISO 105-C10)	-	1000	-
6.5- Table -6, Sl no. 2 (b)(Washing, Staining IS/ISO 105-C11)	-	1000	-
6.5- Table -6, Sl no. 3 (a)(Rubbing, Dry IS/ISO 105-X12)	-	1000	-
6.5- Table -6, Sl no. 3 (b)(Rubbing, Wet IS/ISO 105-X13)	-	1000	-
6.5- Table -6, Sl no. 4 (a)(Perspiration (acidic and alkaline), chenge in colour IS/ISO 105-E04)	-	1000	-
6.5- Table -6, Sl no. 4 (b)(Perspiration (acidic and alkaline), staining IS/ISO 105-E05)	-	1000	-
6.6(Commercial mass)	-	1000	-
6.4 Table 5(Colour Fastness to Light)	-	1000	-
6.1 Table 4(Water soluble matter %)	-	1000	-
6.2 Table 4(Finish Oil Pickup, %)	-	1000	-
6.2 Table 4(Colour difference with reference to srtandard yarn, measured as DE)	-	1000	-
6.5 Table 6(Colour Fastness to light)	-	1000	-
6.5 Table 6(Colour Fastness to Rubbing)	-	1000	-
6.5 Table 6(Colour Fastness to perspiration)	-	1000	-
6.5 Table 6(Colour Fastness to perspiration)	-	1000	-
6.1 Table 3(Colour Fastness to washing , test 2)	-	1000	-
6.1 Table 3(Nominal Linear Density,denier)	-	1000	-
6.1 Table 3(Cross Section)	-	1000	-
6.1 Table 3(No of Filaments)	-	1000	-
6.1 Table 3(Average Tenacity,gpd)	-	1000	-
6.1 Table 3(Elongation ,Percent,Average)	-	1000	-
6.1 Table 3(Interlace as nips per meter)	-	1000	-
6.1 Table 3(Unevenness ,U Percent)	-	1000	-

08 May, 2028

-
-

7036

Amit Test and Calibration Centre (8172006)

8172006

IS 14494 (2019)

Elastomer insulated flexible cables for use in mines - Specification (First Revision)

210000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(CONDUCTOR)	-	500	-
5(INSULATION)	-	500	-
5.1(Power Cores)	-	500	-
5.2(Pilot and Earth Cores)	-	500	-
6(SEMI-CONDUCTING COMPOUND)	-	500	-
7.1(TAPE : Proofed Tape)	-	500	-
7.2(TAPE : Polyethylene Terephalate (PETP) or Polypropylene Base Tape)	-	500	-
8(CENTRE)	-	500	-
9.1(FILLERS)	-	500	-
9.2(FILLERS)	-	500	-
10(CRADLE SEPARATOR)	-	500	-
11.1(ARMOUR)	-	500	-
11.2(ARMOUR)	-	500	-
11.2 a)(ARMOURING: Tensile Strength)	-	1500	-
11.2 b)(ARMOURING: Elongation )	-	1500	-
11.2 c)(ARMOURING: Torsion Test (For round wire ) )	-	1500	-
11.2 d)(ARMOURING: Uniformity of zinc coating)	-	1500	-
11.2 e)(ARMOURING: Mass of zinc coating )	-	1500	-
12.1(SHEATH : Inner Sheath)	-	500	-
12.2(SHEATH : Outer Sheath)	-	500	-
13.1(REINFORCEMENT MATERIAL : Tape)	-	500	-
13.2(REINFORCEMENT MATERIAL : Cord/Yarns)	-	500	-
14.1(CONSTRUCTION : CONDUCTOR)	-	500	-
14.2(CONSTRUCTION : CONDUCTOR)	-	500	-
14.3(CONSTRUCTION : CONDUCTOR)	-	500	-
14.4(CONSTRUCTION : CONDUCTOR)	-	500	-
15(CONDUCTOR SCREENING)	-	500	-
16.1(INSULATION)	-	500	-
16.2(INSULATION : Thickness of Insulation)	-	1000	-
16.3(INSULATION : Tolerance on Insulation Thickness)	-	1000	-
16.4(INSULATION : Application of Insulation)	-	500	-
16.5(INSULATION)	-	500	-
17.1(INSULATION SCREEN)	-	500	-
17.2(INSULATION SCREEN)	-	500	-
17.3(INSULATION SCREEN)	-	500	-
18(PROTECTIVE SCREEN)	-	500	-
19(CONDUCTANCE OF SCREEN)	-	500	-
19.1(Individual Core Screen)	-	500	-
19.2(Collective Screen)	-	500	-
20.1(CORE IDENTIFICATION)	-	500	-
20.2(Colour Scheme for Identification)	-	500	-
20.3(Scheme for Identification by Numbering)	-	500	-
21.1(LAYING UP OF CORES)	-	500	-
21.2(LAYING UP OF CORES)	-	500	-
21.3(LAYING UP OF CORES)	-	500	-
21.4(LAYING UP OF CORES)	-	500	-
22.1(INNER SHEATH)	-	500	-
22.2(Thickness of Inner Sheath)	-	1000	-
22.3(INNER SHEATH)	-	500	-
23.1(ARMOURING)	-	1500	-
23.2(ARMOURING)	-	1500	-
23.3(ARMOURING)	-	1500	-
23.4(ARMOURING)	-	1500	-
24.1(OUTER SHEATH)	-	500	-
24.2(Thickness of Outer Sheath)	-	1000	-
25.1(CABLE CONSTRUCTION AND DIMENSIONS)	-	500	-
27.2(Bending test followed by partial discharge test;)	-	15000	-
27.4(Dielectric power factor test)	-	25000	-
27.5(Heating cycle test followed by partial discharge test;)	-	30000	-
27.6(Impulse voltage test; and)	-	35000	-
26.3(Special Provisions)	-	500	-
27.8(Flammability Test)	-	2500	-
27.9(Water Absorption Test)	-	7000	-
29.1(PACKING AND MARKING)	-	500	-
29.2(PACKING AND MARKING)	-	500	-
30(BIS CERTIFICATION MARKING)	-	500	-
Table 33®, Annex E(Electric tset on semi-conducting screen)	-	2500	-
Table 33(n), Cl. No. 27.7(High Voltage test for 4 hrs.)	-	10000	-
Table 33(j), Cl. No. 27.4(Dielectric Power Factor (as a function of Voltage))	-	30000	-
Table 33(h), Cl. No. 27.2(Partial discharge test)	-	45000	-
Table 33(f)(Insulation resistance)	-	7000	-
Table 33(e)(Tear resistance on sheath)	-	2500	-
Table 33(e)(Oil resistance - Elongation on sheath)	-	5000	-
Table 33(e)(Oil resistance - Tensile strength on sheath)	-	5000	-
Table 33(e)(Permanent set on Sheath)	-	2500	-
Table 33(e)(Hot set on Sheath)	-	2500	-
Table 33(e)(Ageing in air bomb - Elongation on Sheath)	-	5000	-
Table 33(e)(Ageing in air bomb - Tensile strength on Sheath)	-	5000	-
Table 33(e)(Elongation at break on Sheath)	-	2500	-
Table 33(e)(Tensile strength on Sheath)	-	2500	-
Table 33(d)(Ozone resistance on Insulation)	-	15000	-
Table 33(d)(Permanent set on Insulation)	-	2500	-
Table 33(d)(Hot set on Insulation)	-	2500	-
Table 33(d)(Ageing in air bomb - Elongation on Insulation)	-	5000	-
Table 33(d)(Ageing in air bomb - Tensile strength on Insulation)	-	5000	-
Table 33(d)(Ageing in air oven - Elongation on Insulation)	-	5000	-
Table 33(d)(Ageing in air oven - Tensile strength on Insulation)	-	5000	-
Table 33(d)(Elongation at break on Insulation)	-	2500	-
Table 33(d)(Tensile strength on Insulation)	-	2500	-
Table 33(c)(Resistivity of steel wire)	-	1500	-
Table 33(b)(Diameter of armour wire)	-	500	-
Table 4(Copper purity test)	-	5000	-
Table 33(a)(Conductor resistance test)	-	5000	-
Table 33(a)(Annealing test)	-	1500	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath ( Without ageing))	-	2500	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath ( Without ageing))	-	2500	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath ( Without ageing))	-	2500	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath ( After ageing in air bomb)	-	5000	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath ( After ageing in air bomb)	-	5000	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath (Oil resistance test ))	-	5000	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath)	-	2500	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath (Hot set test))	-	2500	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath (Hot set test))	-	2500	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath (Hot set test))	-	2500	-
[ Table 2 of IS:6380-1984](Insulation resistance constant)	-	5000	-
[ Table 2 of IS:6380-1984](Insulation resistance constant)	-	5000	-
[ Cl.5 & Table 2 of IS:6380-1984](Physical tests on Outer Sheath ( Without ageing))	-	2500	-
[ Cl.5 & Table 2 of IS:6380-1984](Physical tests on Outer Sheath ( Without ageing))	-	2500	-
[ Cl.5 & Table 2 of IS:6380-1984](Physical tests on insulation (After ageing in air oven:))	-	5000	-
[ Cl.5 & Table 2 of IS:6380-1984](Physical tests on insulation (After ageing in air oven:))	-	5000	-
[ Cl.5 & Table 2 of IS:6380-1984](Physical tests on insulation (After ageing in air bomb ))	-	5000	-
[ Cl.5 & Table 2 of IS:6380-1984](Physical tests on insulation (After ageing in air bomb ))	-	5000	-
[ Cl.5 & Table 2 of IS:6380-1984](Physical tests on Insulation (Hot set test))	-	2500	-
[ Cl.5 & Table 2 of IS:6380-1984](Physical tests on Insulation (Hot set test))	-	2500	-
[ Cl.4 & 14](Conductor)	-	500	-
[ Cl.4 & 14](Conductor)	-	500	-
[ Cl.4 & 14](Conductor)	-	500	-
[ Cl.4 & 14](Conductor)	-	500	-
[ Cl.4 & 14](Conductor)	-	500	-
[ Cl.4 & 14](Conductor)	-	500	-
[ Cl.4 & 14](Conductor)	-	500	-
[Cl.14.4](Conductor)	-	500	-
Cl. 27.7(High voltage test for 4 hours)	-	10000	-
7.3(TAPE )	-	500	-
17.4(INSULATION SCREEN)	-	500	-
24.3(Tolerance on Thickness of Outer Sheath)	-	1500	-
24.4(OUTER SHEATH)	-	500	-
28(IDENTIFICATION)	-	500	-

16 Apr, 2029

-
Included w.e.f.17.03.2025

7037

VARDAN ENVIROLAB, GURUGRAM

8169616

IS 15844 : Part 3 (2024)

Sports Footwear Part 3 Professional Sports Footwear

Sports Footwear - Part 3 Professional Sports Footwear

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-6(Size and Fittings)	-	150	-
Cl-5(Design)	-	0	-
Cl-6(Size and Fittings)	-	0	-
Cl.7.1.1(Upper to Mid Sole/Out Sole, Upper to Composite Sole (Applicable Only When the Sole is Composite) and Out Sole to Mid Sole (Multilayer, if Present), Bond Performance)	-	400	-
Cl.7.1.2(Energy Absorption at Seat Region)	-	450	-
Cl.7.1.1(Upper to Mid Sole/Out Sole, Upper to Composite Sole (Applicable Only When the Sole is Composite) and Out Sole to Mid Sole (Multilayer, if Present), Bond Performance)	-	0	-
Cl.7.1.2(Energy Absorption at Seat Region)	-	0	-
Cl.7.1.3(Complete Shoe Flexing)	-	600	-
Cl.7.1.4(Washability)	-	600	-
Cl.7.1.5(Slip Resistance)	-	600	-
Cl.7.1.6(Heel Drop)	-	100	-
Cl.7.2 Table-2 S.No- (i)("Flexing resistance, Min a) Dry condition b) Wet condition")	-	300	-
Cl.7.2 Table-2 S.No- (ii)(Tear strength (average force), N, Min)	-	300	-
Cl.7.2 Table-2 S.No- (iii)("Colour fastness rubbing a-Dry b-Wet")	-	300	-
Cl.7.2 Table-2 S.No- (iv)("a) Water vapour permeability b) Water vapour coefficient")	-	450	-
Cl.7.2 Table-2 S.No- (v)(Stitch tear strength N/mm, Min)	-	450	-
Cl.7.2 Table-2 S.No- (vii)(Tensile strength)	-	300	-
Cl.7.2 Table-2 S.No- (viii)(Elongation at break, percent)	-	250	-
Cl.7.2 Table-2 S.No- (ix)("Abrasion test a) Dry b) Wet")	-	600	-
Cl.7.2 Table-3 S.No- (i)(Breaking strength, N/mm, Min)	-	350	-
Cl.7.2 Table-3 S.No- (ii)(Elongation at break, percent, Min)	-	300	-
Cl.7.2 Table-3 S.No- (iii)(Tear strength, N, Min)	-	350	-
Cl.7.2 Table-3 S.No- (iv)(Strength at needle perforation)	-	300	-
Cl.7.2 Table-3 S.No- (v)("Flexing resistance a-Dry condition, b) Wet condition")	-	450	-
Cl.7.2 Table-3 S.No- (vi)("a) Water vapour permeability b) Water vapour coefficient")	-	600	-
Cl.7.2 Table-3 S.No- (vii)(Hydrolysis resistance)	-	650	-
Cl.7.2 Table-3 S.No- (ix)(Bursting strength)	-	350	-
Cl.7.3 Table-4 S.No- (i)(Tear strength, N, Min)	-	350	-
Cl.7.3 Table-4 S.No- (ii)("Abrasion resistance, a) Dry b) Wet ")	-	450	-
Cl.7.3 Table-4 S.No- (iii)(Colour fastness to rubbing, grey scale rate with 10 rubs on dry or wet, Min)	-	450	-
Cl.7.3 Table-4 S.No- (iv)(Colour fastness to perspiration (contact method) grey scale rate, Min)	-	450	-
Cl.7.3 Table-4 S.No- (v)("a-Water vapour permeability b-Water vapour coefficient")	-	600	-
Cl.7.4 Table-5 S.No- (i)(Flexing index, Min)	-	350	-
Cl.7.4 Table-5 S.No- (ii)(Abrasion resistance)	-	450	-
Cl.7.4 Table-5 S.No- (iii)("a) Water absorption b) Water desorption")	-	500	-
Cl.7.5 Table-6 S.No- (i)("Abrasion resistance a) Dry condition b) Wet condition")	-	450	-
Cl.7.5 Table-6 S.No- (ii)("a) Water absorption b) Water desorption")	-	450	-
Cl.7.5 Table-6 S.No- (iii)(Heat resistance shrinkage linear, percent, Max)	-	300	-
Cl.7.6 Table-7 S.No- (i)(Abrasion resistance)	-	450	-
Cl.7.6 Table-7 S.No- (ii)("Flexing resistance a) Bennewart Method b) Ross flexing method")	-	450	-
Cl.7.6 Table-7 S.No- (iii)(Hydrolysis resistance)	-	600	-
Cl.7.6 Table-7 S.No- (iv)(Tear strength, N/mm, Min)	-	300	-
Cl.7.6 Table-7 S.No- (v)(Tensile strength)	-	350	-
Cl.7.6 Table-7 S.No- (vi)(Elongation at break percent, Min)	-	300	-
Cl.7.6 Table-7 S.No- (vii)(Compression set percent, Max)	-	300	-
Cl.7.7 Table-8 S.No- (i)("Compression set, percent, Max a) For EVA b) For all other material")	-	300	-
Cl.7.7 Table-8 S.No- (ii)(Split tear strength)	-	300	-
Cl.7.7 Table-8 S.No- (iii)(Heat shrinkage, percent, Ma)	-	300	-
Cl.7.7 Table-8 S.No- (iii)(Elongation at break, percent, Min)	-	300	-
Cl.7.7 Table-8 S.No- (iv)(Elongation at break, percent, Min)	-	300	-
Cl.7.8 Table-9 S.No- (i)(First dry collapsing load, hardness, N, Min)	-	300	-
Cl.7.8 Table-9 S.No- (ii)(Resilience, percent, Min)	-	300	-
Cl.7.8 Table-9 S.No- (iii)(Moisture resistance, percent, Min)	-	300	-
Cl.7.8 Table-9 S.No- (iv)("a) Initial dry area shape retention, percent, Min b) Area shape retention after 10th collapse, dry, percent, Min ")	-	300	-
Cl.7.8 Table-9 S.No- (v)(Peel strength, N/nm, Min)	-	300	-
Cl.7.9 Table-10 S.No- (i)("Peel strength, N/mm, Min a) Initial b) After 5 000 wear cycles")	-	300	-
Cl.7.9 Table-10 S.No- (ii)("Shear strength, kPa, Min a) Initial b) After 5 000 wear cycles")	-	300	-
Cl.7.10 Table-11 S.No- (i)(Limit of useful extension, percent, Min)	-	300	-
Cl.7.10 Table-11 S.No- (ii)(Needle strength, N/mm, Min)	-	300	-
Cl.7.11 Table-12 S.No- (i)(Breaking strength of lace)	-	300	-
Cl.7.11 Table-12 S.No- (ii)(Lace tag strength)	-	300	-
Cl.7.11 Table-12 S.No- (iii)(Lace to lace abrasion)	-	300	-
Cl.7.11 Table-12 S.No- (iv)(Colour fastness to water (for lace) (Contact method))	-	350	-
Cl.7.11 Table-12 S.No- (v)(Strength of buckle/ski hook/D-ring,)	-	300	-
Cl.7.11 Table-12 S.No- (vi)("Corrosion resistance (applicable for all including decorative metal part) ")	-	650	-
Cl.7.11 Table-13 S.No- (i)(Corrosion resistance (applicable for metallic spikes))	-	650	-
Cl-7.12.1, Table no. 1 of IS 17011,(i)(Allergenic and carcinogenic disperse dyes)	-	1000	-
Cl-7.12.1, Table no. 1 of IS 17011,(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	1000	-
Cl-7.12.1, Table no. 1 of IS 17011,(iv)(Chromium (VI))	-	1400	-
Cl-7.12.1, Table no. 1 of IS 17011,(v)(Dimethyl fumarate (DMFU))	-	1000	-
Cl-7.12.1, Table no. 1 of IS 17011,(vi)(Formaldehyde (free or released by partial hydrolysis))	-	1000	-
Cl-7.12.1, Table no. 1 of IS 17011,(vii)(Formaldehyde)	-	1400	-
Cl-7.12.1, Table no. 1 of IS 17011,(viii)(Organotin compounds)	-	1400	-
Cl-7.12.1, Table no. 1 of IS 17011,(ix)(PCP-TeCP-TriCP polychlorophenols)	-	1400	-
Cl-7.12.1, Table no. 1 of IS 17011,(x)(pH)	-	1400	-
Cl-7.12.1, Table no. 1 of IS 17011,(xi)(Phthalates (each individual phthalate))	-	1400	-
C-7.12.1, Table no. 1 of IS 17011,(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	1400	-
Cl- 8.1(Marking)	-	200	-
Cl-7.12.2(PVC is present in sports shoe)	-	2500	-
Cl-7.12.1, Table no. 1 of IS 17011,(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	1000	-
Cl-7.12.1, Table no. 1 of IS 17011,(viii)(Organotin compounds)	-	1400	-
Cl-7.12.1, Table no. 1 of IS 17011,(vi)(Formaldehyde (free or released by partial hydrolysis))	-	1400	-
Cl-7.12.1, Table no. 1 of IS 17011,(v)(Dimethyl fumarate (DMFU))	-	1400	-
Cl-7.12.1, Table no. 1 of IS 17011,(iv)(Chromium (VI))	-	1400	-
Cl.7.2 Table-2 S.No- (vi)(Colour fastness to light grey scale rate)	-	450	-
Cl.7.2 Table-3 S.No- (viii)(Colour fastness to light grey scale rate)	-	450	-
Cl-6(Size and Fittings)	-	0	-
Cl-5(Design)	-	0	-
Cl-6(Size and Fittings)	-	0	-
Cl.7.1.1(Upper to Mid Sole/Out Sole, Upper to Composite Sole (Applicable Only When the Sole is Composite) and Out Sole to Mid Sole (Multilayer, if Present), Bond Performance)	-	0	-
Cl.7.1.2(Energy Absorption at Seat Region)	-	0	-
Cl.7.1.1(Upper to Mid Sole/Out Sole, Upper to Composite Sole (Applicable Only When the Sole is Composite) and Out Sole to Mid Sole (Multilayer, if Present), Bond Performance)	-	0	-
Cl.7.1.2(Energy Absorption at Seat Region)	-	0	-
Cl.7.1.3(Complete Shoe Flexing)	-	0	-
Cl.7.1.4(Washability)	-	0	-
Cl.7.1.5(Slip Resistance)	-	0	-
Cl.7.1.6(Heel Drop)	-	0	-
Cl.7.2 Table-2 S.No- (i)("Flexing resistance, Min a) Dry condition b) Wet condition")	-	0	-
Cl.7.2 Table-2 S.No- (ii)(Tear strength (average force), N, Min)	-	0	-
Cl.7.2 Table-2 S.No- (iii)("Colour fastness rubbing a-Dry b-Wet")	-	0	-
Cl.7.2 Table-2 S.No- (iv)("a) Water vapour permeability b) Water vapour coefficient")	-	0	-
Cl.7.2 Table-2 S.No- (v)(Stitch tear strength N/mm, Min)	-	0	-
Cl.7.2 Table-2 S.No- (vii)(Tensile strength)	-	0	-
Cl.7.2 Table-2 S.No- (viii)(Elongation at break, percent)	-	0	-
Cl.7.2 Table-2 S.No- (ix)("Abrasion test a) Dry b) Wet")	-	0	-
Cl.7.2 Table-3 S.No- (i)(Breaking strength, N/mm, Min)	-	0	-
Cl.7.2 Table-3 S.No- (ii)(Elongation at break, percent, Min)	-	0	-
Cl.7.2 Table-3 S.No- (iii)(Tear strength, N, Min)	-	0	-
Cl.7.2 Table-3 S.No- (iv)(Strength at needle perforation)	-	0	-
Cl.7.2 Table-3 S.No- (v)("Flexing resistance a-Dry condition, b) Wet condition")	-	0	-
Cl.7.2 Table-3 S.No- (vi)("a) Water vapour permeability b) Water vapour coefficient")	-	0	-
Cl.7.2 Table-3 S.No- (vii)(Hydrolysis resistance)	-	0	-
Cl.7.2 Table-3 S.No- (ix)(Bursting strength)	-	0	-
Cl.7.3 Table-4 S.No- (i)(Tear strength, N, Min)	-	0	-
Cl.7.3 Table-4 S.No- (ii)("Abrasion resistance, a) Dry b) Wet ")	-	0	-
Cl.7.3 Table-4 S.No- (iii)(Colour fastness to rubbing, grey scale rate with 10 rubs on dry or wet, Min)	-	0	-
Cl.7.3 Table-4 S.No- (iv)(Colour fastness to perspiration (contact method) grey scale rate, Min)	-	0	-
Cl.7.3 Table-4 S.No- (v)("a-Water vapour permeability b-Water vapour coefficient")	-	0	-
Cl.7.4 Table-5 S.No- (i)(Flexing index, Min)	-	0	-
Cl.7.4 Table-5 S.No- (ii)(Abrasion resistance)	-	0	-
Cl.7.4 Table-5 S.No- (iii)("a) Water absorption b) Water desorption")	-	0	-
Cl.7.5 Table-6 S.No- (i)("Abrasion resistance a) Dry condition b) Wet condition")	-	0	-
Cl.7.5 Table-6 S.No- (ii)("a) Water absorption b) Water desorption")	-	0	-
Cl.7.5 Table-6 S.No- (iii)(Heat resistance shrinkage linear, percent, Max)	-	0	-
Cl.7.6 Table-7 S.No- (i)(Abrasion resistance)	-	0	-
Cl.7.6 Table-7 S.No- (ii)("Flexing resistance a) Bennewart Method b) Ross flexing method")	-	0	-
Cl.7.6 Table-7 S.No- (iii)(Hydrolysis resistance)	-	0	-
Cl.7.6 Table-7 S.No- (iv)(Tear strength, N/mm, Min)	-	0	-
Cl.7.6 Table-7 S.No- (v)(Tensile strength)	-	0	-
Cl.7.6 Table-7 S.No- (vi)(Elongation at break percent, Min)	-	0	-
Cl.7.6 Table-7 S.No- (vii)(Compression set percent, Max)	-	0	-
Cl.7.7 Table-8 S.No- (i)("Compression set, percent, Max a) For EVA b) For all other material")	-	0	-
Cl.7.7 Table-8 S.No- (ii)(Split tear strength)	-	0	-
Cl.7.7 Table-8 S.No- (iii)(Heat shrinkage, percent, Ma)	-	0	-
Cl.7.7 Table-8 S.No- (iii)(Elongation at break, percent, Min)	-	0	-
Cl.7.7 Table-8 S.No- (iv)(Elongation at break, percent, Min)	-	0	-
Cl.7.8 Table-9 S.No- (i)(First dry collapsing load, hardness, N, Min)	-	0	-
Cl.7.8 Table-9 S.No- (ii)(Resilience, percent, Min)	-	0	-
Cl.7.8 Table-9 S.No- (iii)(Moisture resistance, percent, Min)	-	0	-
Cl.7.8 Table-9 S.No- (iv)("a) Initial dry area shape retention, percent, Min b) Area shape retention after 10th collapse, dry, percent, Min ")	-	0	-
Cl.7.8 Table-9 S.No- (v)(Peel strength, N/nm, Min)	-	0	-
Cl.7.9 Table-10 S.No- (i)("Peel strength, N/mm, Min a) Initial b) After 5 000 wear cycles")	-	0	-
Cl.7.9 Table-10 S.No- (ii)("Shear strength, kPa, Min a) Initial b) After 5 000 wear cycles")	-	0	-
Cl.7.10 Table-11 S.No- (i)(Limit of useful extension, percent, Min)	-	0	-
Cl.7.10 Table-11 S.No- (ii)(Needle strength, N/mm, Min)	-	0	-
Cl.7.11 Table-12 S.No- (i)(Breaking strength of lace)	-	0	-
Cl.7.11 Table-12 S.No- (ii)(Lace tag strength)	-	0	-
Cl.7.11 Table-12 S.No- (iii)(Lace to lace abrasion)	-	0	-
Cl.7.11 Table-12 S.No- (iv)(Colour fastness to water (for lace) (Contact method))	-	0	-
Cl.7.11 Table-12 S.No- (v)(Strength of buckle/ski hook/D-ring,)	-	0	-
Cl.7.11 Table-12 S.No- (vi)("Corrosion resistance (applicable for all including decorative metal part) ")	-	0	-
Cl.7.11 Table-13 S.No- (i)(Corrosion resistance (applicable for metallic spikes))	-	0	-
Cl-7.12.1, Table no. 1 of IS 17011,(i)(Allergenic and carcinogenic disperse dyes)	-	0	-
Cl-7.12.1, Table no. 1 of IS 17011,(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	0	-
Cl-7.12.1, Table no. 1 of IS 17011,(iv)(Chromium (VI))	-	0	-
Cl-7.12.1, Table no. 1 of IS 17011,(v)(Dimethyl fumarate (DMFU))	-	0	-
Cl-7.12.1, Table no. 1 of IS 17011,(vi)(Formaldehyde (free or released by partial hydrolysis))	-	0	-
Cl-7.12.1, Table no. 1 of IS 17011,(vii)(Formaldehyde)	-	0	-
Cl-7.12.1, Table no. 1 of IS 17011,(viii)(Organotin compounds)	-	0	-
Cl-7.12.1, Table no. 1 of IS 17011,(ix)(PCP-TeCP-TriCP polychlorophenols)	-	0	-
Cl-7.12.1, Table no. 1 of IS 17011,(x)(pH)	-	0	-
Cl-7.12.1, Table no. 1 of IS 17011,(xi)(Phthalates (each individual phthalate))	-	0	-
C-7.12.1, Table no. 1 of IS 17011,(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	0	-
Cl- 8.1(Marking)	-	0	-
Cl-7.12.2(PVC is present in sports shoe)	-	0	-
Cl-7.12.1, Table no. 1 of IS 17011,(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	0	-
Cl-7.12.1, Table no. 1 of IS 17011,(viii)(Organotin compounds)	-	0	-
Cl-7.12.1, Table no. 1 of IS 17011,(vi)(Formaldehyde (free or released by partial hydrolysis))	-	0	-
Cl-7.12.1, Table no. 1 of IS 17011,(v)(Dimethyl fumarate (DMFU))	-	0	-
Cl-7.12.1, Table no. 1 of IS 17011,(iv)(Chromium (VI))	-	0	-
Cl.7.2 Table-2 S.No- (vi)(Colour fastness to light grey scale rate)	-	0	-
Cl.7.2 Table-3 S.No- (viii)(Colour fastness to light grey scale rate)	-	0	-

26 Dec, 2027

-
Included w.e.f.17.06.2025

7038

CIPET, Chennai

6104634

IS 7328 (2020)

Specification for Polyethylene Material for Moulding and Extrusion ( Third Revision )

All

3193.75 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2.1.1(Density)	-	1150	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.2.1.2(MFI)	-	825	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.5.6 IS 2530(Carbon black dispersion)	-	525	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.4.3 10 ofIS 2530(Carbon black content)	-	693.75	Testing Charges after 25% concession for BIS ( GST Extra as applicable)

31 Mar, 2027

-
-

7039

CIPET, Chennai

6104634

IS 10151 (2019)

Polyvinyl chloride (Pvc) and its copolymers for its safe use in contact with foodstuffs, pharmaceuticals and drinking water - Specification (First Revision)

all

4625 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.4(Monomer content)	-	2625		Testing Charges after 25% concession for BIS ( GST Extra as applicable)
4.5(Overall Migration, IS 9845)	-	2000		Testing Charges after 25% concession for BIS ( GST Extra as applicable)

31 Mar, 2027

-
-

7040

CIPET, Chennai

6104634

IS 12252 (2017)

Polyalkylene terephthalates (Pet And Pbt), their copolymers and list of constituents in raw materials and end products for their safe use in contact with foodstuffs and pharmaceuticals (First Revision)

all

2688 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.3(Overall Migration,Max)	-	1900		After 25% discount on test charges for BIS Identification Charges -787.5

31 Mar, 2027

-
-

7041

CIPET, Chennai

6104634

IS 2508 (2016)

Polyethylene films and sheets - Specification (Third Revision)

upto 1 mm

16731 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1(Appearance)	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.1.2(Film Form)	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.1.3(Odour)	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.1.4(Density, Cl.5 of IS 13360(Part-3/Section-1))	-	525	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.1.5(Melt Flow Index. Cl 6, 7 of IS 13360(Part-4/Section-1))	-	825	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.1.6a(Carbon Black Content, Annex-A)	-	693.75	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.1.6b(Ash Content, Annex-A)	-	900	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.1.6c(Carbon Black Dispersion, Cl.16 of IS 2530)	-	525	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.2.2(Tolerance on Thickness, Annex-A)	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
6.1, Table 1(Tensile strength at break. A) Machine Direction. IS 13360 (Part 5/Sec 1))	-	1475	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
6.1, Table 1(Tensile strength at break. B) Transverse Direction. IS 13360 (Part 5/Sec 3))	-	975	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
6.1, Table 1(Ageing test at (70-1)c for 7 days , cl 4 IS 7016 )	-	4200	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
6.1, Table 1(Elongation at break ,A) Machine direction .IS 13360(Part-5/sec-1) )	-	0	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
6.1, Table 1(Elongation at break ,B) Cross-machine direction..IS 13360(Part-5/sec-3) )	-	0	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
6.1, Table 1(Dartimpact strength Method B of IS 13360 (Part-5/sec-6) )	-	637.5	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
6.1, Table 1(Tear resistence. A) Machine direction Annex B)	-	1325	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
6.1, Table 1(Tear resistence. B) Transverse direction )	-	825	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
7.1. Table 2(Tensile strength at break A) Machine direction IS 13360 (Part-5/sec-1) )	-	1475	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
7.1. Table 2(Tensile strength at break,B) Crosse machine direction IS 13360 (Part-5/sec-3) )	-	975	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
7.1. Table 2(Ageing test at (70-1)c for 7 days , cl 4 IS 7016 )	-	4200	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
7.1. Table 2(Elongation at break , A) Machine direction IS 13360 (Part-5/sec-3) IS 13360 (Part-5/sec-1) )	-	0	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
7.1. Table 2(Elongation at break , A) Transverse direction IS 13360 (Part-5/sec-3) )	-	0	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
7.1. Table 2(Dart impact strenght , Method A of IS 3360 (Part-5/sec-6) )	-	637.5	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.1, Table 3(Tensile properties ,A) Yield strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1475	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.1, Table 3(Tensile properties , B) Break strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	975	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.1, Table 3(Tensile properties ,C) Yield elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.1, Table 3(Tensile properties ,D) Break elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.1, Table 3(Tear resistance , Annex B)	-	1325	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.1, Table 3(Puncture resistance , Annex C)	-	825	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
9.1, Table 4(Tensile properties ,A) Yield strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1475	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
9.1, Table 4(Tensile properties , B) Break strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	975	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
9.1, Table 4(Tensile properties ,C) Yield elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
9.1, Table 4(Tensile properties ,D) Break elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
9.1, Table 4(Tear resistance , Annex B)	-	1325	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
9.1, Table 4(Puncture resistance , Annex C)	-	925	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
Clause 7.1(Table 2)(Decrease in Tensile Strength after Ageing(Transverse Direction))	-	975	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
Clause 7.1(Table 2)(Decrease in Tensile Strength after Ageing(Machine Direction))	-	975	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
Clause 6.1(Table 1)(Decrease in Tensile Strength after Ageing(Transverse Direction))	-	975	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
Clause 6.1(Table 1)(Decrease in Tensile Strength after Ageing(Machine Direction))	-	975	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.2.1.1(Nominal Thickness)	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.2.1.2(Nominal width)	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)

31 Mar, 2027

-
-

7042

CIPET, Chennai

6104634

IS 13592 (2013)

Unplasticized Polyvinyl Chloride (PVC-U) Pipes for Soil and Waste Discharge System Inside and Outside Buiildings Including Ventilation and Rainwater System

upto 315 mm diameter

17662.5 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.5(Surface colour of the pipes shall be dark shade of grey)	-	375	Testing Charges after 25% concession( GST Extra as applicable)
Cl6.3(The composition shall be based on PVC resin having a K-value of 64 or greater when tested in accordance with IS 4669)	-	825	Testing Charges after 25% concession( GST Extra as applicable)
Cl.7.1(Mean out side Diameter (For less than or equal to 40 mm- Average of 8 , For higher diameters up to 110 mm average of 6))	-	375	Testing Charges after 25% concession( GST Extra as applicable)
Cl.7.1(Outside Diameter at any point (Take 8 reading reported minimum, maximum))	-	0	Testing Charges after 25% concession( GST Extra as applicable)
Cl.7.1(Wall thickness "minimum,maximum" (Take 8 reading))	-	0	Testing Charges after 25% concession( GST Extra as applicable)
Cl.7.2(Pipes shall be supplied in nominal lengths of 2, 3, 4 or 6 metres either plain or with socket for solvent cementing/grooved socket. Tolerances on specified length shall be + 10 mm and – 0 mm.The nominal length of the pipe with socket for solvent cementing/grooved socket shall be as given in Fig. 1.)	-	375	Testing Charges after 25% concession( GST Extra as applicable)
Cl.7.3.1(Minimum wall thickness of socket on pipes shall be as given in Table 2 read with Fig. 2 and Fig. 3.)	-	0	Testing Charges after 25% concession( GST Extra as applicable)
Cl.7.3.2(Dimensions of sockets for solvent cementing and grooved sockets of pipes shall be as given in Tables 3 and 4 respectively, read with Fig. 2 and 3.)	-	0	Testing Charges after 25% concession( GST Extra as applicable)
Cl.8.1(The internal and external surface of the pipes shall be smooth and clean, and free from grooving and other defects. The end shall be clearly cut and shall be square with the axis of the pipe. The end may be chamfered on the plain side.)	-	375	Testing Charges after 25% concession( GST Extra as applicable)
Cl.8.2(When tested by the method described in IS 12235 (Part 5), a length of pipe sample of 200 ± 20 mm shall not alter in length by more than 5 percent. In the case of socket ended pipes, this test shall be carried out on the plain portion of pipe taken at least 100 mm away from the root of the socket.)	-	1025	Testing Charges after 25% concession( GST Extra as applicable)
Cl8.3(This test shall be carried out for socket end pipes only. When tested by the method described in IS 12235 (Part 6), the test specimens shall not show blisters, excessive delamination or cracking or signs of weld line splitting.)	-	525	Testing Charges after 25% concession( GST Extra as applicable)
Cl.8.4(When determined in accordance with IS 12235 (Part 2), the vicat softening temperature of the specimen shall not be less than 79°C.)	-	825	Testing Charges after 25% concession( GST Extra as applicable)
Cl.8.5(After the required period of exposure, the tensile strengths of two samples when tested as per IS 12235 (Part 13) shall not show difference of more than 20 percent of their initial tensile strengths)	-	4475	Exposure charges Effect on Sunlight Rs. 3500/- Tensile Strength After Exposure RS. 1475/- Testing Charges after 25% concession( GST Extra as applicable)
Cl. 9, IS 12235 Part 7(Resistance to Sulphuric Acid)	-	2000	Testing Charges after 25% concession( GST Extra as applicable)
Cl.10.1(When tested by method prescribed in IS 12235 (Part 9),the pipe shall have a true impact rate of not more than 10 percent. Mass of striker and height of fall shall be as per Annex A.)	-	1325	Testing Charges after 25% concession( GST Extra as applicable)
Cl.10.2(When determined in accordance with the method described in IS 12235 (Part 13), the tensile strength at break shall not be less than 45 MPa.)	-	1475	Testing Charges after 25% concession( GST Extra as applicable)
Cl.10.3(The axial shrinkage shall not exceed 2 percent when determined in accordance with Annex B.)	-	637.5	Testing Charges after 25% concession( GST Extra as applicable)
Cl.11.(Jointing of solvent cementing joints is to be carried out using solvent conforming to IS 14182. Apply a pressure of 0.05 MPa for a period of 15 min and there should be no leakage at any joint.)	-	750	Testing Charges after 25% concession( GST Extra as applicable)
Cl. 12, IS 12235 Part 11(Resistance to Di-Chloro-Methane)	-	750	Effect on water - Rs.2250/- Testing Charges after 25% concession( GST Extra as applicable)

31 Mar, 2027

-
-

7043

CIPET, Chennai

6104634

IS 4985 (2021)

UNPLASTICIZED PVC PIPES FOR POTABLE WATER SUPPLIES SPECIFICATION Fourth Revision

upto 355mm diameter

20013 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1.2(PVC Resin)	-	3075	Testing Charges after 25% concession( GST Extra as applicable)
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	375	Testing Charges after 25% concession( GST Extra as applicable)
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-	0	Testing Charges after 25% concession( GST Extra as applicable)
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	375	Testing Charges after 25% concession( GST Extra as applicable)
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-	0	Testing Charges after 25% concession( GST Extra as applicable)
7.1.1.2(DIMENSIONS-PIPE-Ovality (Maximum))	-	0	Testing Charges after 25% concession( GST Extra as applicable)
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	187.50	Testing Charges after 25% concession( GST Extra as applicable)
7.1.2.1(DIMENSIONS-PIPE-Thickness(Maximum))	-	0	Testing Charges after 25% concession( GST Extra as applicable)
7.1.2.1(DIMENSIONS-PIPE-Average Thickness)	-	0	Testing Charges after 25% concession( GST Extra as applicable)
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	375	Testing Charges after 25% concession( GST Extra as applicable)
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-	0	Testing Charges after 25% concession( GST Extra as applicable)
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-	0	Testing Charges after 25% concession( GST Extra as applicable)
7.2.1.2(a)-Table 5(DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-	0	Testing Charges after 25% concession( GST Extra as applicable)
7.2.1.2-Table 4(DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-	0	Testing Charges after 25% concession( GST Extra as applicable)
9.1(PIPE ENDS)	-	0	Testing Charges after 25% concession( GST Extra as applicable)
10.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	375	Testing Charges after 25% concession( GST Extra as applicable)
10.1.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	0	Testing Charges after 25% concession( GST Extra as applicable)
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	525	Testing Charges after 25% concession( GST Extra as applicable)
10.3(Effect on Water Test)	-	2250	Testing Charges after 25% concession( GST Extra as applicable)
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	1025	Testing Charges after 25% concession( GST Extra as applicable)
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	825	Testing Charges after 25% concession( GST Extra as applicable)
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	525	Testing Charges after 25% concession( GST Extra as applicable)
10.7(Sulphated Ash Content)	-	900	Testing Charges after 25% concession( GST Extra as applicable)
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	8250	Testing Charges after 25% concession( GST Extra as applicable)
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	637.50	Testing Charges after 25% concession( GST Extra as applicable)
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	8250	Testing Charges after 25% concession( GST Extra as applicable)
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	637.50	Testing Charges after 25% concession( GST Extra as applicable)
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	637.50	Testing Charges after 25% concession( GST Extra as applicable)
11.2(Resistance to External Blows at 0°C)	-	1250	Testing Charges after 25% concession( GST Extra as applicable)
7.1.3(mean outside diameter, outside diameter at any point, and wall thickness of plumbing pipes)	-	375	Testing Charges after 25% concession( GST Extra as applicable)
7.1.4(Length)	-	375	Testing Charges after 25% concession( GST Extra as applicable)

31 Mar, 2027

-
-

7044

CIPET, Chennai

6104634

IS 12818 (2010)

Unplasticized polyvinyl chloride (Pvc - U) screen and casing pipes for bore/tubewells - Specification (Second Revision)

upto 200mm

12900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1 (VCM Content as per IS 10151 (Annex A))	-	2250	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
4.1.2(K-Value as per IS-4669)	-	825	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
5(COLOUR)	-	375	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Nominal Diameter)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Mean Outer Diameter of Pipe)	-	1250	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Outer Diameter at any point )	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Mean Outer Diameter over Connection)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Wall thickness)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.2 and Table 5, 6 & 7 Fig 1B(DIMENSIONS - Casing Pipes)	-	1250	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.2 and Table 5, 6 & 7 Fig 1B(Nominal Diameter)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter of Pipe, Min)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter of Pipe , Max)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.1, 7.2 and Table 5, 6 & 7 Fig 1B(Outer Diameter at any point , Min)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.1, 7.2 and Table 5, 6 & 7 Fig 1B(Outer Diameter at any point, Max)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.1, 7.2 and Table 5, 6 & 7 Fig 1B(Mean outside dia over connection,mm (Take 4 reading and maximum valu reported))	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Min)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Max)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.3.1(No.of Ribs)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.3.2(Rib height)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.4 Table 8 & 9 Fig 1(Effective length, l2)	-	375	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.4 Table 8 & 9 Fig 1(Segmental length, l3)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.4 Table 8 & 9 Fig 1(Segmental length,mm for socket (average of 4.0))	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.4 Table 8 & 9 Fig 1(Segmental length for Spigot (average of 4.0))	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.5 and Table 10 Fig 2A & 2B(Summation of slot lengths over internal circumference of the cross- section.)	-	375	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.5 and Table 10 Fig 2A & 2B(Minimum number of slots on the circumference of the cross-section.)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.5 and Table 10 Fig 2A & 2B(Approximate Free Passage Area, in Percent (Mean Value) for Width of Slot (w))	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
8.1 to 8.3 and Table 11 &12 Fig 3A & 4A(THREADING OF SCREEN ANDCASING PIPES. IS 554.)	-	375	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
8.4(Sealing rings - Hardness)	-	375	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	375	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
9.1(Visual Appearance)	-	375	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
9.2(Internal Diameter)	-	375	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
9.3(Density IS 12235 (Part 14))	-	525	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
9.4 and Table 14(Resistance to External Blows at 0 ?C IS 12235 (Part 9))	-	1250	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
9.5(Tensile Strength IS 12235(Part 13))	-	1475	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
9.6(Vicat Softening Temperature IS 12235 (Part 2).)	-	825	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
9.7(Effect on Water a) Lead (first extraction) b) Lead (Third extraction) c) Dialkyl Tin C4 & higher homologues measured as Tin (Third extraction) d) Cadmium (All three extracts) e) Mercury (All three extracts) f) Other Toxic Substances )	-	2250	Testing Charges after 25% concession to BIS ( GST Extra as applicable)

31 Mar, 2027

-
-

7045

CIPET, Chennai

6104634

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

Upto 355 mm

40824.75 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.2(Colour)	-	375	Testing Charges after 25% concession( GST Extra as applicable)
6.2.1(6.1.1 Identification Stripes)	-	375	Testing Charges after 25% concession( GST Extra as applicable)
7()	-	0	Testing Charges after 25% concession( GST Extra as applicable)
7.2(Length)	-	375	Testing Charges after 25% concession( GST Extra as applicable)
Cl-7.4(Mean Outside Diameter (For upto 50 mm take 8 reading, above 50mm take 6 reading & average will be reported))	-	562.5	Testing Charges after 25% concession( GST Extra as applicable)
7.4.1.2(Ovality)	-	0	Testing Charges after 25% concession( GST Extra as applicable)
8,/8.1/8.1.1 table-5(PERFORMANCE REQUIREMENTS / Hydraulic Characteristics/ Internal Pressure Creep Rupture Test of Pipe)	-	16550	Testing Charges after 25% concession( GST Extra as applicable)
8.1.2 table -5(Internal Pressure Creep Rupture Test of Pipe Joints)	-	1200	Testing Charges after 25% concession( GST Extra as applicable)
8.2(Longitudinal Reversion Test)	-	1025	Testing Charges after 25% concession( GST Extra as applicable)
8.3(Carbon black)	-	1218.75	Testing Charges after 25% concession( GST Extra as applicable)
8.4( Melt Flow Rate)	-	825	Testing Charges after 25% concession( GST Extra as applicable)
8.5 (Oxidation Induction Time)	-	1650	Testing Charges after 25% concession( GST Extra as applicable)
8.6(Overall migration)	-	1775	Testing Charges after 25% concession( GST Extra as applicable)
8.7(Density)	-	525	Testing Charges after 25% concession( GST Extra as applicable)
8.8(Tensile Strength for Butt-fusion)	-	1475	Testing Charges after 25% concession( GST Extra as applicable)
8.9 table-6(Elongation at Break)	-	1475	Testing Charges after 25% concession( GST Extra as applicable)
8.10(Slow Crack Growth Rate)	-	4625	Testing Charges after 25% concession( GST Extra as applicable)
5, 5.1 table-1(MATERIALS)	-	0	Testing Charges after 25% concession( GST Extra as applicable)
5.2(Polyethylene Resin)	-	4675	Testing Charges after 25% concession( GST Extra as applicable)
5.3(d)(Carbon Black Master Batch)	-	1218.75	Testing Charges after 25% concession( GST Extra as applicable)
5.3(e)(Carbon Black Master Batch)	-	900	Testing Charges after 25% concession( GST Extra as applicable)

31 Mar, 2027

-
-

7046

CIPET, Chennai

6104634

IS 9537 : Part 5 (2000)

Conduits four electrical installations - Part 5 pliable conduits of insulating material

All type

7975 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Dimension)	-	750	Testing Charges after 25% concession( GST Extra as applicable)
8(Construction)	-	375	Testing Charges after 25% concession( GST Extra as applicable)
9.2(Bending Test)	-	750	Testing Charges after 25% concession( GST Extra as applicable)
9.3(Compression Test)	-	825	Testing Charges after 25% concession( GST Extra as applicable)
9.5(Callapse Test)	-	825	Testing Charges after 25% concession( GST Extra as applicable)
10(Resistance to heat)	-	525	Testing Charges after 25% concession( GST Extra as applicable)
11(Resistance to burning)	-	525	Testing Charges after 25% concession( GST Extra as applicable)
12(Electrical characteristics)	-	2650	Testing Charges after 25% concession( GST Extra as applicable)

31 Mar, 2027

-
Included w.e.f. 01-09-2017.

7047

CIPET, Chennai

6104634

IS 13488 (2008)

Irrigation equipment - Emitting pipe systems - Specification (First Revision)

all

12825 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.2 (Ref. Cl 4.1.c & 4.2.a of IS 12786 : 1989)(Carbon Black content - IS 2530 : 1963)	-	693.75	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.1.2 (Ref. Cl 4.2.b of IS 12786 : 1989)(The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963)	-	525	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
6.2.2(Fittings)	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
6.3(General)	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.3.1(Wall Thickness ofEmitting Pipe)	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.3.2(Inside Diameter ofEmitting Pipe)	-	0	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.3.3(Flow Paths in Emitting Unit)	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.3.4(Spacing ofEmitter Units)	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.1.2(Uniformity of Emission Rate for Unregulated Emitting Pipes)	-	750	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.1.3(Uniformity of Emission Rate for Regulated Emitting Pipes)	-	750	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.2(Emission Rate of Emitting Unit as a Function of Inlet Pressure)	-	750	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.4.1(Resistance to Hydrostatic Pressure at Ambient Temperature)	-	750	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.4.2(Resistance to Hydrostatic Pressure at Elevated Temperature)	-	1200	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.5(Resistance to Tension at Elevated Temperature)	-	825	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.6(Resistance to Pull Out of Joints Between Fitting and Emitting IS 13479)	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.7.1(Resistance of PE Emitting Pipe to Environmental Stress Cracking -Acceptance Test Annex D of IS 12786)	-	900	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.7.2(Resistance of PE Emitting Pipe to Environmental Stress Cracking - Type Test Annex D of IS 12786)	-	1200	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.8(Determination of Emitting Unit Exponent)	-	450	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.1.2 (Ref. Cl 4.1.a of IS 12786 : 1989)(Potyethylene - higher olefins constituent )	-	787.5	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.1.2 (Ref. Cl 4.1.c.ii of IS 12786 : 1989)(Toluene extract - Annex A of IS 12786:1989)	-	750	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.1.2 (Ref. Cl 4.1.c.iii of IS 12786 : 1989)(Volatile matter - Annex B of IS 12786:1989)	-	525	Testing Charges after 25% concession for BIS ( GST Extra as applicable)

31 Mar, 2027

-
-

7048

CIPET, Chennai

6104634

IS 14887 (2014)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg food grains – Specification (first revision)

All

25292.5 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2(Tapes – Width and Thickness ( IS 6192/IS 11197))	-	750	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
3.2(Tapes – Linear Density (IS 6192/IS 11197))	-	525	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
3.2(Tapes – Tenacity (IS 6192/IS 11197))	-	825	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
3.2(Tapes – Elongation at point of rupture (IS 6192/IS 11197))	-	0	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
3.2(Tapes – Heat Shrinkage (HDPE) (Cl. 3.2 and IS 6192))	-	1275	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
3.2(Tapes – Dimensional stability (PP) (IS 11197))	-	1050	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
3.3.1(Bottom seam (IS 10789))	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
4.1 and 3.4(Mass of bale (Cl. 4.1), Capacity (Cl 3.4))	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
4.2 and Table 1 ii(Dimensions )	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.2 and Table 1 iii(Ends per dm )	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.2 and Table 1 iv(Picks per dm )	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
4.2 and Table 1 v(Mass of sack )	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
4.2 and Table 1 vi(Average breaking strength of fabric )	-	1650	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
4.2 and Table 1 vi(Breaking strength of bottom seam )	-	825	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
4.2 and Table 1 viii(Elongation at break of fabric )	-	0	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
4.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	11830	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
4.2 and Table 1 x(Ash content )	-	900	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
3.2(MFI)	-	825	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
3.2(Density)	-	525	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
3.1(Overall Migration)	-	1275	Testing Charges after 25% concession for BIS ( GST Extra as applicable)

31 Mar, 2027

-
-

7049

CIPET, Chennai

6104634

IS 2533 (1978)

Specification for geometry boxes (First Revision)

all

19125 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No.3(MATERIALS)	-	9000	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
Cl. No.5, Table no.1and 2(DIMENSIONS AND TOLERANCES)	-	6750	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
Cl. No.6(GRADUATIONS)	-	3375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)

31 Mar, 2027

-
Included w.e.f. 19-09-2017.

7050

CIPET, Chennai

6104634

IS 9537 : Part 1 (1980)

Specification for conduits for electrical installations: Part 1 general requirements

7975 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Dimensions)	-	750	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8(Constrution)	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
9 & 9.2("Mechanical properties Bending test ")	-	750	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
9.3(Compression test)	-	825	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
9.4(Impact test)	-	825	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
9.5(Collapse test)	-	750	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
10(Resistance to heat)	-	525	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
11(Resistance to burning)	-	525	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
12(Electrical strength test & Insulation resistance test)	-	2650	Testing Charges after 25% concession for BIS ( GST Extra as applicable)

31 Mar, 2027

-
Included w.e.f. 01-09-2017.

Bureau of Indian Standards

The National Standards Body of India

Search by IS Number