BIS - LIMS (Laboratory Information Management System)

Search by IS Number

Reset

15472 Results

S.No.

Lab Name

Osl Code

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

7051

Star Wire (India) Laboratories Private Ltd., Ballabhgarh

8141826

IS 15885 : Part 2 : Sec 13 (2012)

Safety of lamp controlgear: Part 2 particular requirements: Sec 13 d.c. or a.c. supplied electronic controlgear for led modules

52500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking)	-	2000	Nil
8(Protection against accidental contact with live parts)	-	5000	Nil
10(PROVISION FOR EARTHING)	-	3000	Nil
11(MOISTURE RESISTANCE)	-	5000	Nil
12(Electric Strength)	-	5000	Nil
13(Thermal endurance test for winding of ballasts)	-	5000	Nil
14(Fault conditions)	-	8000	Nil
15(Transformer heating)	-	5000	Nil
16(Construction)	-	5000	Nil
17(Creepage distance and clearances)	-	3000	Nil
18(Screws, current carrying parts and connections)	-	5000	Nil
19(Resistance to heat, fire and tracking)	-	5000	Nil
20(Resistance to corrosion)	-	3000	Nil
9(Terminals)	-	5000	Nil

17 Sep, 2027

-
Excluding: Testing of Components Enclosure, Bridging resistor in primary circuit, Capacitor and RC units, RF suppression (X-Y capacitors), Inductor, MOV/VDR, SMPS/Mains Transformer, PCB material, Metal base PCB for LED, Transparent cover, Bobbin, Insulated tape, Heat shrinkage sleeve, Connector, Fuse, Internal wire, LED, Optocoupler, EMI/EMC filter, Winding wire, Thin sheet materials etc.

7052

Star Wire (India) Laboratories Private Ltd., Ballabhgarh

8141826

IS 16102 : Part 1 (2012)

Self - Ballasted led lamps for general lighting services: Part 1 safety requirements

49500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Marking)	-	2000	NIL
6(Interchangeability)	-	5000	NIL
7(Protection against accidental contact with live parts)	-	5000	NIL
8(Insulation Resistance and Electric Strength)	-	5000	NIL
9(MECHANICAL STRENGTH)	-	5000	NIL
10(cap temperature)	-	8000	NIL
11(Resistance to Heat)	-	5000	NIL
12(Resistance to Flame and Ignition)	-	8000	NIL
13(Fault conditions)	-	6000	NIL
14(Creepage distance and clearances)	-	3000	NIL

17 Sep, 2027

-
Restricted to Cap type B22d, E14 & E27 only.

7053

BIS, Southern Regional Laboratory (SRL)

None

IS 710 (2010)

Marine plywood - Specification (Second Revision)

Rs 11200/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 (DIMENSIONS)	-
6.1 (DIMENSIONS)	-
6.2 (DIMENSIONS)	-
6.3 (DIMENSIONS)	-
6.3 (DIMENSIONS)	-
9.1.1 (MOISTURE CONTENT)	-
9.1.2 , 9.1.2.1 (Glue Adhesion in Dry State)	-
9.1.2 , 9.1.2.2 (Glue Adhesion in Dry State)	-
9.1.3 , 9.1.3.1.1 (Water resistance test)	-
9.1.3 , 9.1.3.1.2 (Water resistance test)	-
9.1.4 (Tensile strength)	-
9.1.5 (Mycological test)	-
9.1.5 , 9.1.3.1.1 (Mycological test)	-
Cl.9.1.5,9.1.3.1.1 (Cl.9.1.5 (Mycological Test),9.1.3.1.1 ( Glue Shear Strength: Average))	-
Cl. 9.1.4 (Cl. 9.1.4 (Tensile Strength: Sum of the Tensile Strength in two directions))	-
Cl. 9.1.4 (Cl. 9.1.4 (Tensile Strength: Perpendicular to grain))	-
Cl. 9.1.4 (Cl. 9.1.4 (Tensile Strength: Parallel to grain))	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Rupture: Across the Face Grain: Minimum Individual))	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Rupture: Across the Face Grain: Average))	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Rupture: Along the Face Grain: Minimum Individual))	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Rupture: Along the Face Grain: Average))	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Elasticity: Across the Face Grain: Minimum Individual))	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Elasticity: Across the Face Grain: Average))	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Elasticity: Along the Face Grain: Minimum Individual))	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Elasticity: Along the Face Grain: Average))	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Rupture: Across the Face Grain: Minimum Individual))	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Rupture: Across the Face Grain: Average))	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Rupture: Along the Face Grain: Minimum Individual))	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Rupture: Along the Face Grain: Average))	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Elasticity: Across the Face Grain: Minimum Individual))	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Elasticity: Across the Face Grain: Average))	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Elasticity: Along the Face Grain: Minimum Individual))	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Elasticity: Along the Face Grain: Average))	-
11.1 (MARKING)	-

-
Quantity Required: 2 Nos of Marine Plywood Sheets

7054

BIS, Southern Regional Laboratory (SRL)

None

IS 303 (1989)

Plywood for General Purposes -

Rs 4000/- /BWR Grade, Rs.4900/- for MR Grade Rs 4000/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8 (Dimensions & Tolerances - Squareness - Annexure C)	-
11.4, Table 4 (Static Bending Strength - Modulus of Rupture - Across the Face Grain - Minimum Individual)	-
11.4, Table 4 (Static Bending Strength - Modulus of Rupture - Across the Face Grain - Average)	-
11.4, Table 4 (Static Bending Strength - Modulus of Rupture - Along the Face Grain - Minimum Individual)	-
11.4, Table 4 (Static Bending Strength - Modulus of Rupture - Along the Face Grain - Average)	-
11.4, Table 4 (Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Minimum Individual)	-
11.4, Table 4 (Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Average)	-
11.4, Table 4 (Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Minimum Individual)	-
11.4, Table 4 (Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average)	-
11.2.2 (Glue Adhesion - Mycological test - 11.2.2, Part 7 of IS 1734 [for MR Garde only])	-
11.2.1 (Glue Adhesion - Water resistance test - 11.2.1.1 [for MR Grade])	-
11.2.1 (Glue Adhesion - Water resistance test - 11.2.1.1 [for BWR Grade])	-
11.3 (Moisture Content - Part 1 of IS 1734)	-
9 (Workmanship and Finish - Cl.9, 8.3, Annexure C)	-
5.1 (Type - For BB Type)	-

-
Quantity Required: 2 Nos of Full Sheets

7055

Winwall Technology India Private Limited,Thiruvallur

6171906

IS 18648 (2024)

Classification and Performance Requirements for Doors Windows and Sliders - Specification

600000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
As per Clause 7.3(Doors, Windows and Sliders)	-	75000	-
As per Clause 7.4.2(Doors, Windows and Sliders)	-	75000	-
As per Clause 7.4.3(Doors, Windows and Sliders)	-	75000	-
As per Clause 7.4.4(Doors, Windows and Sliders)	-	75000	-
As per Clause 7.5(Doors, Windows and Sliders)	-	365000	-
As per Clause 6.1.6(Doors, Windows and Sliders)	-	10000	-

-
Included w.e.f. 31.12.2024 Only for operating force (Cl.6.1.6), Air permeability (Cl.7.3), Water tightness (Cl.7.4), Resistance to wind load (Cl.7.5)

7056

KC INDIA TEST LABORATORIES LLP, GHAZIABAD

9140406

IS 7098 : Part 2 (2011)

Crosslinked polyethylene insulated thermoplastic sheathed cables - Specification: Part 2 for working voltages from 3.3 kV up to and including 33 kV (Second Revision)

Size: 25 to 2500 sqmm

190000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(CONDUCTOR)	-	200	NIL
4.1.1(CONDUCTOR)	-	200	NIL
5(INSULATION)	-	200	NIL
6(SCREENING)	-	200	NIL
6.1.1(SCREENING : - Non-metallic — Semiconducting Compound)	-	200	NIL
6.1.2(SCREENING : - Non-magnetic Metallic Tape for Single Core Unscreened and Unarmoured Cables)	-	200	NIL
7(FILLERS AND INNER SHEATH)	-	500	NIL
8.1(ARMOURING)	-	200	NIL
8.2(ARMOURING)	-	200	NIL
9(OUTER SHEATH )	-	200	NIL
10.1(CONDUCTOR)	-	200	NIL
10.2(CONDUCTOR)	-	200	NIL
11(CONDUCTOR SCREENING)	-	200	NIL
12.1(INSULATION)	-	200	NIL
12.2(INSULATION : Thickness of Insulation)	-	200	NIL
12.3(INSULATION : Tolerance on Thickness of Insulation)	-	200	NIL
12.4(Eccentricity and Ovality)	-	200	NIL
12.5(INSULATION : Application of Insulation)	-	200	NIL
13.1(INSULATION SCREENING)	-	200	NIL
13.2(INSULATION SCREENING)	-	200	NIL
13.3(INSULATION SCREENING)	-	200	NIL
13.4(INSULATION SCREENING)	-	200	NIL
14.1(CORE IDENTIFICATION)	-	200	NIL
14.1.1(CORE IDENTIFICATION)	-	200	NIL
15.1(LAVING UP OF CORES)	-	200	NIL
16.1(INNER SHEATH (COMMON COVERING))	-	200	NIL
16.2(INNER SHEATH (COMMON COVERING))	-	200	NIL
16.2.1(INNER SHEATH (COMMON COVERING))	-	200	NIL
16.3(INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-	200	NIL
16.3.1(INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-	200	NIL
17.1(ARMOURING : Application )	-	200	NIL
17.1.1(ARMOURING )	-	200	NIL
17.1.2(ARMOURING )	-	200	NIL
17.1.3(ARMOURING )	-	200	NIL
17.2(ARMOURING : Type of armour )	-	200	NIL
17.2.1(ARMOURING : Type of armour )	-	200	NIL
17.2(ARMOURING : Coverage )	-	200	NIL
17.3(ARMOURING : Dimension )	-	200	NIL
17.4(ARMOURING : Joints)	-	200	NIL
16.4(ARMOURING : Resistance)	-	200	NIL
18.1(OUTER SHEATH)	-	200	NIL
18.2(OUTER SHEATH: Colour)	-	200	NIL
18.3(Thicknes of outer sheath : average )	-	200	NIL
18.3(Thicknes of outer sheath : minimum )	-	200	NIL
19.1 i) a)(Annealing test (for copper))	-	500	NIL
19.1 i) b)(Tensile test (for aluminium) - Before stranding )	-	1000	NIL
19.1 i) b)(Tensile test (for aluminium) - After stranding )	-	1000	NIL
19.1 i) c)(Wrapping test ( for aluminium))	-	1000	NIL
19.1 i) d)(Resistance test - Main conductor )	-	1000	NIL
19.1 i) d)(Resistance test - Neutral conductor )	-	1000	NIL
19.1 iii) a)(Phyaical tests for insulation : Tensile Test)	-	1000	NIL
19.1 iii) a)(Phyaical tests for insulation : Elongation )	-	1000	NIL
19.1 iii) b)(Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	1000	NIL
19.1 iii) b)(Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	1000	NIL
19.1 iii) c)(Degree of cross linking )	-	1000	NIL
19.1 iii) d)(Phyaical tests for insulation : Hot set )	-	1000	NIL
19.1 iii) d)(Phyaical tests for insulation : Permanent set )	-	1000	NIL
19.1 iii) e)(Phyaical tests for insulation : Shrinkage )	-	1000	NIL
19.1 iii) e)(Phyaical tests for insulation : Shrinkage - Crack observed )	-	1000	NIL
19.1 iii) f)(Insulation: Waterabsorption(gravimetric))	-	2500	NIL
19.1 v) a)(Test for strippability of semiconducting strippable insulation screen (when applicable))	-	1000	NIL
19.1 v) b)(Volume resistivity)	-	1500	NIL
19.1 vi) a)(Physical tests for outer sheath : Tensile stregth )	-	1500	NIL
19.1 vi) a)(Physical tests for outer sheath : Elongation )	-	1500	NIL
19.1 vi) b)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	1500	NIL
19.1 vi) b)(Physical tests for outer sheath -Ageing in air oven : Elongation )	-	1500	NIL
19.1 vi) c)(Phyaical tests for Sheath : Shrinkage )	-	1500	NIL
19.1 vi) c)(Phyaical tests for Sheath : Shrinkage - Crack observed )	-	1500	NIL
19.1 vi) d)(Sheath : Hot deformation)	-	1500	NIL
19.1 vi) e)(Loss of massIn air oven)	-	1500	NIL
19.1 vi) f)(Sheath : Heat shock test)	-	1500	NIL
19.1 vi) g)(Sheath : Thermalstability)	-	1500	NIL
19.1 vi) h)(Carbon black content of polythene sheath )	-	1500	NIL
19.1 vii)(Thermal ageing test for complete cable - Tensile stregth )	-	1500	NIL
19.1 vii)(Thermal ageing test for complete cable- Elogation )	-	1500	NIL
19.1 vii)(Thermal ageing test for complete cable- Resistivity )	-	1500	NIL
19.1 xi)(Insulation resistance test : volume resistivity )	-	1500	NIL
20.2(Partial discharge test)	-	35000	NIL
20.3(Bending test)	-	1000	NIL
20.4(Dielectric power factor test : As a function of voltage)	-	1000	NIL
20.4(Dielectric power factor test : As a function of temperature)	-	1000	NIL
20.5(Heating Cycle Test)	-	25000	NIL
20.6(Impulse withstand test (Rated voltage, kV 3.8/6.6 Impulse voltage, kV 60))	-	25000	NIL
20.7(High voltage test)	-	25000	NIL
20.8(Flammability test)	-	5000	NIL
20.1(Oxygen Index Test)	-	5000	NIL
20.11(Flame Retardance Test on Single Cables)	-	5000	NIL
20.12(Flame Retardance Test on Bunched Cables)	-	8000	NIL
20.13(Test for Halogen Acid Gas Evolution)	-	8000	NIL
20.14( Test for Smoke Density)	-	5000	NIL
20.15(Temperature Index)	-	5000	NIL
21.1(IDENTIFICATION : Manufacturer's Identification)	-	200	NIL
21.2(IDENTIFICATION : Cable Identification)	-	200	NIL
21.3(IDENTIFICATION : Cable Code)	-	200	NIL
20.3 (a)(Partial discharge test (Bending test))	-	35000	NIL
20.5 (a)(PD test (heating cycle test))	-	35000	NIL
20.6(Impulse Withstand Test (Rated voltage, kV 6.35/11 Impulse voltage, kV 75))	-	25000	NIL
20.6(Impulse Withstand Test (Rated voltage, kV 11/11 Impulse voltage, kV 95))	-	25000	NIL
20.6(Impulse Withstand Test (Rated voltage, kV 12.7/22 Impulse voltage, kV 125))	-	25000	NIL
20.6(Impulse Withstand Test (Rated voltage, kV 19/33 Impulse voltage, kV 170))	-	25000	NIL
19.1 vi) b)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	1000	NIL
19.1 vi) b)(Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	1000	NIL

06 Jun, 2027

-
Size: 25 to 2500 sqmm

7057

KC INDIA TEST LABORATORIES LLP, GHAZIABAD

9140406

IS 7098 : Part 3 (1993)

Cross - Linked polyethylene insulated thermoplastic sheathed cables - Specification: Part 3 for working voltages from 66 kV up to and including 220 kV

Size: 95-2500 sqmm

550000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(CONDUCTOR)	-	1000	NIL
5(INSULATION)	-	1000	NIL
6(SCREENING)	-	1000	NIL
7.1(MOISTURE BARRIER : Laminated Tape)	-	1000	NIL
7.2(MOISTURE BARRIER : Lead Alloy Sheath)	-	1000	NIL
7.3(MOISTURE BARRIER : Water Blocking Tape/Powder)	-	1000	NIL
8.1(INNER SHEATH)	-	1000	NIL
8.2(INNER SHEATH)	-	1000	NIL
8.3(INNER SHEATH)	-	1000	NIL
9.1(ARMOUR)	-	1000	NIL
9.2(ARMOUR)	-	1000	NIL
10.1(OUTER SHEATH)	-	1000	NIL
10.2(OUTER SHEATH)	-	1000	NIL
11.1(CONDUCTOR)	-	1000	NIL
11.2(CONDUCTOR)	-	1000	NIL
12.1(CONDUCTOR SCREENING )	-	1000	NIL
12.2(CONDUCTOR SCREENING )	-	1000	NIL
13.1(INSULATION)	-	1000	NIL
13.2(INSULATION)	-	1000	NIL
14.1(INSULATION SCREENING)	-	1000	NIL
14.2.1(INSULATION SCREENING : Non-metallic Part)	-	1000	NIL
14.2.2(INSULATION SCREENING : Non-metallic Part)	-	1000	NIL
14.2.3(INSULATION SCREENING : Non-metallic Part)	-	1000	NIL
14.3.1(INSULATION SCREENING : Metallic Part)	-	1000	NIL
14.3.2(INSULATION SCREENING : Metallic Part)	-	1000	NIL
14.3.3(INSULATION SCREENING : Metallic Part)	-	1000	NIL
15.1(MOISTURE BARRIER)	-	1000	NIL
15.2.1(Metallic Sheath)	-	1000	NIL
15.2.2(Metallic Sheath)	-	1000	NIL
16.1(INNER SHEATH)	-	1000	NIL
16.2(INNER SHEATH)	-	1000	NIL
17.1(ARMOUR)	-	1000	NIL
17.2(ARMOUR)	-	1000	NIL
17.3(ARMOUR)	-	1000	NIL
17.4(ARMOUR)	-	1000	NIL
17.5(ARMOUR)	-	1000	NIL
18.1(OUTER SHEATH)	-	1000	NIL
18.2(outer sheath colour)	-	1000	NIL
18.3.1(Thickness of Outer Sheath : Unarmoured Cables)	-	2500	NIL
18.3.1(Thickness of Outer Sheath : armoured Cables)	-	2500	NIL
19.1 A) I)(Tests on conductor : Annealing test ( for copper ))	-	2500	NIL
19.1 A) II)(Tests on conductor : Resistance test)	-	5000	NIL
19.1 b) I)(Test for thickness and dimensions of insulation)	-	5000	NIL
19.1 b) II)(Tensile strength and elongation at break)	-	5000	NIL
19.1 b) III)(Thermal ageing in air oven)	-	5000	NIL
19.1 b) IV)(Hot set test)	-	5000	NIL
19.1 b) V)(Shrinkage test)	-	5000	NIL
20.3(Test for concentric metallic screen : Test for concentric copper wire)	-	5000	NIL
20.4(Test for concentric copper tape)	-	5000	NIL
20.5(Thickness of metallic sheath)	-	5000	NIL
20.6(Tests for armouring material : Dimensions)	-	5000	NIL
19.1 f) II)(Tests for armouring material : Tensile strength and elongation at break)	-	5000	NIL
Table 9, (Measurement of thickness)	-	5000	NIL
19.1 g)2) i)(PVC sheath : Tensile strength and elongation at break)	-	5000	NIL
19.1 g)2) iii)(PVC sheath : Loss of mass)	-	5000	NIL
19.1 g)2) v)(PVC sheath : Hot deformation test)	-	5000	NIL
19.1 g)2) vi)(PVC sheath : Shrinkage test)	-	5000	NIL
19.1 g)2) vii)(PVC sheath : Thermal stability)	-	5000	NIL
19.1 g)3) ii)(PE sheath : Tensile strength and elongation at break before and after ageing)	-	5000	NIL
19.1 g)3) iii)(PE sheath : Hot-detormation)	-	5000	NIL
20.7(Flammabihty test ( for PVC outer sheathed cables only ))	-	8000	NIL
20.8.3(Water tightness test)	-	8000	NIL
20.9.1(Thermal ageing on complete cable sample)	-	8000	NIL
19.1 k) ii)(Tensile strength and elongation at breakfor insulation and outer sheath)	-	5000	NIL
20.2(Resistivity test for semi-conducting layer)	-	5000	NIL
20.11.1(Bending test followed by P D test)	-	70000	NIL
20.12, 20.18(Dielectric power factor and capacitance measurement at ambient temperature)	-	5000	NIL
20.13(Dielectric power factor measurement at elevated temperature)	-	5000	NIL
20.14.1(Load cycle test followed by P.D measurement)	-	70000	NIL
20.15(Impulse Voltage Test Followed by High Voltage Test)	-	50000	NIL
19.5(Check on Insulation Thickness Before the Electrical Type Tests)	-	5000	NIL
20.16.1(Test for Dimensions of Insulation : Insulation Thickness)	-	5000	NIL
20.16.2(Test for Dimensions of Insulation : Test for Eccentricity)	-	5000	NIL
20.16.3(Test for Dimensions of Insulation : Test for Ovality)	-	5000	NIL
20.17(High Voltage Test ( as Routine and Acceptance Tests ) )	-	50000	NIL
20.18(Measurement of Capacitance)	-	5000	NIL

06 Jun, 2027

-
Size: 95-2500 sqmm

7058

Alpha Test House Services LLP (160), Sahibzada Ajit Singh Nagar

9138706

IS 1161 (2014)

Steel tubes for structural purposes - Specification (Fifth Revision)

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 6(Outer Diameter, Thickness & Mass)	-	11000	15% DISCOUNT TO BIS
Cl 7(Workmanship)	-	11000	15% DISCOUNT TO BIS
Cl 8(Workmanship)	-	11000	15% DISCOUNT TO BIS
Cl 9(Workmanship)	-	11000	15% DISCOUNT TO BIS
Cl 13(Workmanship)	-	11000	15% DISCOUNT TO BIS
Cl 6(Outer Diameter, Thickness & Mass)	-	11000	15% DISCOUNT TO BIS
Cl 7(Workmanship)	-	11000	15% DISCOUNT TO BIS
Cl 11(Tensile Test, Flattening Test & Cold Bend Test)	-	11000	15% DISCOUNT TO BIS
8 AND AS PER IS 4736(UNIFORMITY OF ZINC COATING)	-	11000	15% DISCOUNT TO BIS
8 AND AS PER IS 4736(MASS OF ZINC COATING)	-	11000	15% DISCOUNT TO BIS
5 AND AS PER IS 10748(COPPER)	-	11000	15% DISCOUNT TO BIS
5 AND AS PER IS 10748(MICRO ALLOY)	-	11000	15% DISCOUNT TO BIS
5 AND AS PER IS 10748(CARBON EQUIVALENT)	-	11000	15% DISCOUNT TO BIS
5 AND AS PER IS 10748(CARBON)	-	11000	15% DISCOUNT TO BIS
Clause - 5.1, Table-3( ALUMINIUM)	-	11000	15% DISCOUNT TO BIS
Clause - 5.1, Table-3(SILICON)	-	11000	15% DISCOUNT TO BIS
Clause - 5.1, Table-3(NITROGEN)	-	11000	15% DISCOUNT TO BIS
Clause - 5.1, Table-3(MANGANESE)	-	11000	15% DISCOUNT TO BIS
Clause - 5.1, Table-3(PHOSPHURS)	-	11000	15% DISCOUNT TO BIS
Clause - 5.1, Table-3(SULPHUR)	-	11000	15% DISCOUNT TO BIS
Clause - 5.1, Table-3( CARBON)	-	11000	15% DISCOUNT TO BIS
9(Straightness)	-	11000	15% DISCOUNT TO BIS
10(Lengths)	-	11000	15% DISCOUNT TO BIS
Cl 11.3.1(Cold bend test (upto & including 50 mm NB))	-	11000	15% DISCOUNT TO BIS
Cl. 11.2 Table 2(Elongation)	-	11000	15% DISCOUNT TO BIS
Cl. 11.2 Table 2(Yield strength)	-	11000	15% DISCOUNT TO BIS
Cl. 6 , 6.2 Table 1(Radius of gyration)	-	11000	15% DISCOUNT TO BIS
Cl. 6 , 6.2 Table 1(Moment of inertia)	-	11000	15% DISCOUNT TO BIS
Cl. 6 , 6.2 Table 1(Surface internal)	-	11000	15% DISCOUNT TO BIS
Cl. 6 , 6.2 Table 1(Surface external)	-	11000	15% DISCOUNT TO BIS
Cl. 6 , 6.2 Table 1(Internal volume)	-	11000	15% DISCOUNT TO BIS
Cl. 6 , 6.2 Table 1(Area of cross section)	-	11000	15% DISCOUNT TO BIS
Cl. 6 , 6.2 Table 1(Weight)	-	11000	15% DISCOUNT TO BIS
Cl. 6 , 6.2 Table 1(Thickness)	-	11000	15% DISCOUNT TO BIS
Clause 11.2, Table -2(Elongation)	-	500	15% DISCOUNT TO BIS
13.0(Oiling and Painting - Visual)	-	11000	15% DISCOUNT TO BIS

31 Dec, 2026

-
-

7059

Universal Testing and Research Centre (Division of Sustainable Stewardship Private Limited)

8169306

IS 14587 (2023)

Prelaminated Medium Density Fibre Board - Specification

Grade 1 & 2

15200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.1(Medium Density Fibre (MDF) Board)	-	0	10% Discount for BIS Samples
Cl-7(Finish)	-	200	10% Discount for BIS Samples
Cl-8.1(Dimensions of prelaminated MDF)	-	500	10% Discount for BIS Samples
Cl-8.2(Tolerances)	-	250	10% Discount for BIS Samples
Cl-8.2.1(Edge straightness)	-	250	10% Discount for BIS Samples
Cl-9.1 S.No-(1), i(Density, kg/m3)	-	500	10% Discount for BIS Samples
Cl-9.1 S.No-(1), ii(Variation from mean density, percent)	-	0	ok
Cl-9.1 S.No-(1), iii(Moisture content, percent)	-	500	10% Discount for BIS Samples
Cl-9.1 S.No-(1), iv(Variation from mean moisture content, percent (absolute))	-	0	ok
Cl-9.1 S.No-(1), v(Linear expansion (thickness swelling in water), due to general absorption after 24 h soaking, percent, Max)	-	500	10% Discount for BIS Samples
Cl-9.1 S.No-(1), vi(Internal bond strength, N/mm2, Min)	-	500	10% Discount for BIS Samples
Cl-9.1 S.No-(1), vii,a(After cyclic test)	-	500	10% Discount for BIS Samples
Cl-9.1 S.No-(1), vii,b(After accelerated water resistance test)	-	0	ok
Cl-9.1 S.No-(1), viii(Modulus of rupture, N/mm2 , Min)	-	1250	10% Discount for BIS Samples
Cl-9.1 S.No-(1), ix(Modulus of elasticity, N/mm2 , Min)	-	1250	10% Discount for BIS Samples
Cl-9.1 S.No-(1), x,(Screw withdrawal strength, ????????, Min)	-	500	10% Discount for BIS Samples
Cl-9.1 S.No-(1), xi(Formaldehyde content (Fc), mg/100 g for oven dry board)	-	5500	10% Discount for BIS Samples
Cl-9.1 S.No-(1), xii(Steady-state formaldehyde emission (Fc), mg/m3)	-	60000	20% Discount for BIS Samples (Optional Test, Mentioned charges are for the Steady State Formaldehyde Testing 60000/- , Testing Time 30Days)
Cl-9.1 S.No-(1), xiii(Abrasion resistance in number of revolutions, Min, (Type 1 to 4))	-	1000	10% Discount for BIS Samples
Cl-9.1 S.No-(1), xiv(Resistance to steam/water vapours)	-	500	10% Discount for BIS Samples
Cl-9.1 S.No-(1), xv(Resistance to crack)	-	500	10% Discount for BIS Samples
Cl-9.1 S.No-(1), xvi(Resistance to a cigarette burn)	-	500	10% Discount for BIS Samples
Cl-9.1 S.No-(1), xvii(Resistance to stain)	-	500	10% Discount for BIS Samples
Cl-11.2(Specific Requirement)	-	0	ok
Cl-12(Marking)	-	0	ok

28 Nov, 2027

-
-

7060

Universal Testing and Research Centre (Division of Sustainable Stewardship Private Limited)

8169306

IS 12406 (2021)

Medium density fibre boards for general purpose - Specification

Grade 1 & 2

12200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clauses 5.2, 9 and 10.2.2(Density)	-	500	10% Discount for BIS Samples
Clauses 5.2, 9 and 10.2.2(Density)	-	500	10% Discount for BIS Samples
Clauses 5.2, 9 and 10.2.2(Variation from mean density)	-	200	10% Discount for BIS Samples
Clauses 5.2, 9 and 10.2.2(Moisture Content)	-	500	10% Discount for BIS Samples
Clauses 5.2, 9 and 10.2.2(Variation from mean moisture content)	-	200	10% Discount for BIS Samples
Clauses 5.2, 9 and 10.2.2(Linear expansion (Thickness Swelling in Water) Due to general Absorption after 24h soaking)	-	1000	10% Discount for BIS Samples
Clauses 5.2, 9 and 10.2.2(Internal Bond Strength)	-	500	10% Discount for BIS Samples
Clauses 5.2, 9 and 10.2.2(Internal Bond strength (i) (After Cyclic test) (ii) (After accelerated water resistance test))	-	1000	10% Discount for BIS Samples
Clauses 5.2, 9 and 10.2.2(Modulus of Rupture a) Avg. Value b) Min. Individual)	-	1000	10% Discount for BIS Samples
Clauses 5.2, 9 and 10.2.2(Modulus of Elasticity a) Avg. Value b) Min. Individual)	-	500	10% Discount for BIS Samples
Clauses 5.2, 9 and 10.2.2(Screw withdrawl strength (i) Face (ii) Edge (For thickness >12mm))	-	1000	10% Discount for BIS Samples
Clauses 5.2, 9 and 10.2.2(Formaldehyde Content (i) For Formaldehyde Class, E1 (ii) For Formaldehyde Class, E2)	-	5500	10% Discount for BIS Samples
Clauses 5.2, 9 and 10.2.2(Steady State Formaldehyde emission (Fc (i) For Formaldehyde Class, E1 (ii) For Formaldehyde Class, E2)	-	45000	20% Discount for BIS Samples (Optional Test, Mentioned charges are for the Steady State Formaldehyde Testing 60000/- , Testing Time 30Days)
8(DIMENSIONS AND TOLERANCES)	-	500	10% Discount for BIS Samples

28 Nov, 2027

-
-

7061

Universal Testing and Research Centre (Division of Sustainable Stewardship Private Limited)

8169306

IS 12823 (2015)

Prelaminated Particle Boards from Wood and other Lignocellulosic Material - Specification ( First Revision )

Grade 1& 2

13500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 7(Finish)	-	500	10% Discount for BIS Samples
Cl 8(Dimensions & Tolerances)	-	2000	10% Discount for BIS Samples
Cl 10.2(Test For Density)	-	1000	10% Discount for BIS Samples
Cl 10.3(Test For Moisture Content)	-	1000	10% Discount for BIS Samples
Cl 10.4(For Water AbsorptionTest )	-	1000	10% Discount for BIS Samples
Cl 10.5(For Swelling in water Test )	-	1000	10% Discount for BIS Samples
Cl 10.6(Tesr For Modulus Of Elasticity & Mudulus Of Rupture)	-	3000	10% Discount for BIS Samples
Cl 10.7(For Determination of Tensile Strength Perpendicular to Surface)	-	1000	10% Discount for BIS Samples
Cl 10.8(For Determination of Tensile Strength Perpendicular to Surface After Ageing Test)	-	1000	10% Discount for BIS Samples
Cl 10.9(Test For Screw Withdrawal Strength)	-	1000	10% Discount for BIS Samples
Cl 10.10 & Annex C( Test For Abrasion Resistance)	-	1000	10% Discount for BIS Samples
Cl 10.11 & Annex D( Test For Resistance to Steam)	-	1000	10% Discount for BIS Samples
Cl 10.12 & Annex E( Test For Crack Resistance)	-	1000	10% Discount for BIS Samples
Cl 10.13 & Annex F( Test For Resistance to Cigarette Burn)	-	1000	10% Discount for BIS Samples
Cl 10.14 & Annex G( Test For Resistance to Stain)	-	1000	10% Discount for BIS Samples
Cl 4(Grades & Types)	-	0	ok
Cl 10.15(Test for Formaldehyde Content/Emission)	-	4800	10% Discount for BIS Samples according test IS 13745 20% Discount for BIS Samples (Optional Test, Mentioned charges are for the Steady State Formaldehyde Testing 60000/- , Testing Time 30Days)

28 Nov, 2027

-
-

7062

Universal Testing and Research Centre (Division of Sustainable Stewardship Private Limited)

8169306

IS 3087 (2005)

Practicle boards of wood and other lingnocellulosic materials (medium density) for general purposes -Specification

Grade 1& 2

16700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
1 (i) Table 1(Density Variation (Flat Pressed Single Layer))	-	1000	10% Discount for BIS Samples
1 (i) Table 1(Density Variation (Flat Pressed Three Layer grade 1))	-	1000	10% Discount for BIS Samples
1 (i) Table 1(Density Variation (Flat Pressed Three Layer grade 2))	-	1000	10% Discount for BIS Samples
1 (i) Table 1(Density Variation (Extrusion Pressed Solids) XPS)	-	1000	10% Discount for BIS Samples
1 (i) Table 1(Density Variation (Extrusion Pressed Tubular) XPS)	-	1000	10% Discount for BIS Samples
1 (ii) (a) Table 1(Water absorption, 2h soacking (Flat Pressed Single Layer))	-	1000	10% Discount for BIS Samples
1 (ii) (a) Table 1(Water absorption, 2h soacking (Flat Pressed Three Layer grade 1))	-	1000	10% Discount for BIS Samples
1 (ii) (a) Table 1(Water absorption, 2h soacking (Flat Pressed Three Layer grade 2))	-	1000	10% Discount for BIS Samples
1 (ii) (a) Table 1(Water absorption, 2h soacking (Extrusion Pressed Solids) XPS)	-	1000	10% Discount for BIS Samples
1 (ii) (a) Table 1(Water absorption, 2h soacking (Extrusion Pressed Tubular) XPS)	-	1000	10% Discount for BIS Samples
1 (ii) Table 1 (b)(Water absorption, 24h soacking (Flat Pressed Single Layer))	-	1000	10% Discount for BIS Samples
1 (ii) (b) Table 1 (Water absorption, 24h soacking (Flat Pressed Three Layer grade 1))	-	1000	10% Discount for BIS Samples
1 (ii) (b) Table 1 (Water absorption, 24h soacking (Flat Pressed Three Layer grade 2))	-	1000	10% Discount for BIS Samples
1 (ii) (b) Table 1 (Water absorption, 24h soacking (Extrusion Pressed Solids) XPS)	-	1000	10% Discount for BIS Samples
1 (ii) (b) Table 1 (Water absorption, 24h soacking (Extrusion Pressed Tubular) XPS)	-	1000	10% Discount for BIS Samples
1 (iii) (a) Table 1(Linear expression (swelling in water), Length (Flat Pressed Single Layer))	-	3000	10% Discount for BIS Samples
1 (iii) (a) Table 1(Linear expression (swelling in water), Length (Flat Pressed Three Layer grade 1))	-	3000	10% Discount for BIS Samples
1 (iii) (a) Table 1(Linear expression (swelling in water), Length (Flat Pressed Three Layer grade 2))	-	3000	10% Discount for BIS Samples
1 (iii) (a) Table 1(Linear expression (swelling in water), Length (Extrusion Pressed Solids) XPS)	-	3000	10% Discount for BIS Samples
1 (iii) (a) Table 1(Linear expression (swelling in water), Length (Extrusion Pressed Tubular) XPS)	-	3000	10% Discount for BIS Samples
1 (iii) (b) Table 1(Linear expression (swelling in water), Width (Flat Pressed Single Layer))	-	3000	10% Discount for BIS Samples
1 (iii) (b) Table 1(Linear expression (swelling in water), Width (Flat Pressed Three Layer grade 1))	-	3000	10% Discount for BIS Samples
1 (iii) (b) Table 1(Linear expression (swelling in water), Width (Flat Pressed Three Layer grade 2))	-	3000	10% Discount for BIS Samples
1 (iii) (b) Table 1(Linear expression (swelling in water), Width (Extrusion Pressed Solids) XPS)	-	3000	10% Discount for BIS Samples
1 (iii) (b) Table 1(Linear expression (swelling in water), Width (Extrusion Pressed Tubular) XPS)	-	3000	10% Discount for BIS Samples
1 (iv) Table 1(Thickness swelling, Width (Flat Pressed Single Layer))	-	3000	10% Discount for BIS Samples
1 (iv) Table 1(Thickness swelling, Width (Flat Pressed Three Layer grade 1))	-	3000	10% Discount for BIS Samples
1 (iv) Table 1(Thickness swelling, Width (Flat Pressed Three Layer grade 2))	-	3000	10% Discount for BIS Samples
1 (iv) Table 1(Thickness swelling, Width (Extrusion Pressed Solids) XPS)	-	3000	10% Discount for BIS Samples
1 (iv) Table 1(Thickness swelling, Width (Extrusion Pressed Tubular) XPS)	-	3000	10% Discount for BIS Samples
1 (v) Table 1(Swelling in thickness due to surface absorption, (Flat Pressed Single Layer))	-	3000	10% Discount for BIS Samples
1 (v) Table 1(Swelling in thickness due to surface absorption, (Flat Pressed Three Layer grade 1))	-	3000	10% Discount for BIS Samples
1 (v) Table 1(Swelling in thickness due to surface absorption, (Flat Pressed Three Layer grade 2))	-	3000	10% Discount for BIS Samples
1 (v) Table 1(Swelling in thickness due to surface absorption, (Extrusion Pressed Solids) XPS)	-	3000	10% Discount for BIS Samples
1 (v) Table 1(Swelling in thickness due to surface absorption, (Extrusion Pressed Tubular) XPS)	-	3000	10% Discount for BIS Samples
1 (vi) (a), Table 1(Modulus of rupture, Average (Flat Pressed Single Layer))	-	3000	10% Discount for BIS Samples
1 (vi) (a), Table 1(Modulus of rupture, Average (Flat Pressed Three Layer grade 1))	-	3000	10% Discount for BIS Samples
1 (vi) (a), Table 1(Modulus of rupture, Average (Flat Pressed Three Layer grade 2))	-	3000	10% Discount for BIS Samples
1 (vi) (a), Table 1(Modulus of rupture, Average (Extrusion Pressed Solids) XPS)	-	3000	10% Discount for BIS Samples
1 (vi) (a), Table 1(Modulus of rupture, Average (Extrusion Pressed Tubular) XPS)	-	3000	10% Discount for BIS Samples
1 (vii) (a), Table 1(Modulus of elasticity, Average (Flat Pressed Single Layer))	-	3000	10% Discount for BIS Samples
1 (vii) (a), Table 1(Modulus of elasticity, Average (Flat Pressed Three Layer grade 1))	-	3000	10% Discount for BIS Samples
1 (vii) (a), Table 1(Modulus of elasticity, Average (Flat Pressed Three Layer grade 2))	-	3000	10% Discount for BIS Samples
1 (vii) (a), Table 1(Modulus of elasticity, Average (Extrusion Pressed Solids) XPS)	-	3000	10% Discount for BIS Samples
1 (vii) (a), Table 1(Modulus of elasticity, Average (Extrusion Pressed Tubular) XPT)	-	3000	10% Discount for BIS Samples
1 (viii) (a), Table 1(Tensile strenath perpendicullr to surface, Upto 20mm thickness (Flat Pressed Single Layer))	-	1000	10% Discount for BIS Samples
1 (viii) (a), Table 1(Tensile strenath perpendicullr to surface,Upto 20mm thickness (Flat Pressed Three Layer grade 1))	-	1000	10% Discount for BIS Samples
1 (viii) (a), Table 1(Tensile strenath perpendicullr to surface, Upto 20mm thickness (Flat Pressed Three Layer grade 2))	-	1000	10% Discount for BIS Samples
1 (viii) (a), Table 1(Tensile strenath perpendicullr to surface, Upto 20mm thickness (Extrusion Pressed Solids) XPS)	-	1000	10% Discount for BIS Samples
1 (viii) (a), Table 1(Tensile strenath perpendicullr to surface, Upto 20mm thickness (Extrusion Pressed Tubular) XPT)	-	1000	10% Discount for BIS Samples
1 (viii) (b), Table 1(Tensile strenath perpendicullr to surface, Above 20mm thickness (Flat Pressed Single Layer))	-	1000	10% Discount for BIS Samples
1 (viii) (b), Table 1(Tensile strenath perpendicullr to surface,Above 20mm thickness (Flat Pressed Three Layer grade 1))	-	1000	10% Discount for BIS Samples
1 (viii) (b), Table 1(Tensile strenath perpendicullr to surface, Above 20mm thickness (Flat Pressed Three Layer grade 2))	-	1000	10% Discount for BIS Samples
1 (viii) (b), Table 1(Tensile strenath perpendicullr to surface, Above 20mm thickness (Extrusion Pressed Solids) XPS)	-	1000	10% Discount for BIS Samples
1 (viii) (b), Table 1(Tensile strenath perpendicullr to surface, Above 20mm thickness (Extrusion Pressed Tubular) XPT)	-	1000	10% Discount for BIS Samples
7(Finish)	-	1000	10% Discount for BIS Samples
8.3(Dimensional Tolerances)	-	2000	10% Discount for BIS Samples
9.2, 11.4(Moisture content)	-	1000	10% Discount for BIS Samples
11.10(screw withdrawal strength)	-	1000	10% Discount for BIS Samples

28 Nov, 2027

-
-

7063

Universal Testing and Research Centre (Division of Sustainable Stewardship Private Limited)

8169306

IS 1659 (2004)

Block boards - Specification (Fourth Revision)

MR & BWP

7200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.2.6(Spot test - Annexure L)	-	1500	10% Discount for BIS Samples
9.2.5(Modulus of elasticity - MINIMUM INDIVIDUAL - Annexure K)	-	1600	10% Discount for BIS Samples
9.2.5(Modulus of elasticity - AVERAGE - Annexure K)	-	1600	10% Discount for BIS Samples
9.2.5(Modulus of rupture - MINIMUM INDIVIDUAL - Annexure K)	-	1600	10% Discount for BIS Samples
9.2.5(Modulus of rupture - AVERAGE - Annexure K)	-	1600	10% Discount for BIS Samples
9.2.4(Mycological Test [for MR grade only] - Annexure J)	-	1500	10% Discount for BIS Samples
9.2.3(Adhesion of Plies - Annexure H)	-	600	10% Discount for BIS Samples
9.2.2 (Resistance to water - Annexure G, Annexure H [For MR Grade])	-	1000	10% Discount for BIS Samples
9.2.2 (Resistance to water - Annexure G, Annexure H [For BWP grade])	-	1000	10% Discount for BIS Samples
9.2.1(Dimensional Changes caused by humidity Change in local planeness - Annexure F)	-	1000	10% Discount for BIS Samples
9.2.1(Dimensional Changes caused by humidity - Delamination - Annexure F)	-	1000	10% Discount for BIS Samples
9.2.1(Dimensional Changes caused by humidity - Change in thickness - at 40% RH - Annexure F)	-	1000	10% Discount for BIS Samples
9.2.1(Dimensional Changes caused by humidity - Change in Thickness - at 90% RH - Annexure F)	-	1000	10% Discount for BIS Samples
9.2.1(Dimensional Changes caused by humidity - Change in Length - at 40% RH - Annexure F)	-	1000	10% Discount for BIS Samples
9.2.1(Dimensional Changes caused by humidity - Change in Length - at 90% RH - Annexure F)	-	1000	10% Discount for BIS Samples
7.3(Dimensional Requirements - Variation in thickness - Annexure E)	-	1000	10% Discount for BIS Samples
7.3(Dimensional Requirements - Squareness - Annexure D)	-	500	10% Discount for BIS Samples
7.3(Dimensional Requirements - Edge Straightness - Annexure D)	-	500	10% Discount for BIS Samples
7.3(Dimensional Requirements - Thickness - Annexure E)	-	500	10% Discount for BIS Samples
7.3(Dimensional Requirements - Width - 8.1.4)	-	500	10% Discount for BIS Samples
7.3(Dimensional Requirements - Length - 8.1.4)	-	500	10% Discount for BIS Samples
8.1.3, 6.3.3, IS 1328(Visual Inspection - Permissible Defects - IS 1328 [test method for DECORATIVE type])	-	500	10% Discount for BIS Samples
8.1.3, 6.3.3, IS 303(Visual Inspection - Permissible Defects - IS 303 [test method for COMMERCIAL type])	-	500	10% Discount for BIS Samples
9.2.6 (mechanical)(Spot test - Annexure L)	-	1500	10% Discount for BIS Samples
cl. 11(marking)	-	0	-
cl. 11.1(marking - BIS certification marking)	-	0	-

28 Nov, 2027

-
-

7064

Universal Testing and Research Centre (Division of Sustainable Stewardship Private Limited)

8169306

IS 10701 (2012)

Structural plywood - Specification (First Revision)

BWP & BWR

17500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11.3(Glue Shear strength in dry state)	-	2000	10% Discount for BIS Samples
11.4.1(Resistance to Water)	-	2000	10% Discount for BIS Samples
11.4.2(Resistance to Water)	-	1000	10% Discount for BIS Samples
11.6(Tensile Strength)	-	1600	10% Discount for BIS Samples
11.7.1(Compressive Strength, Bending Strength, Panel Shear Strength, Plate Shear Strength and Rolling Shear Strngth)	-	6000	10% Discount for BIS Samples
11.8(Wet Bending Strength)	-	5000	10% Discount for BIS Samples
Clause 11.2(Moisture content)	-	1000	10% Discount for BIS Samples

28 Nov, 2027

-
-

7065

Universal Testing and Research Centre (Division of Sustainable Stewardship Private Limited)

8169306

IS 1328 (1996)

Veneered Decorative Plywood -Specification

MR & BWR

5500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Grade - For BWR)	-	500	10% Discount for BIS Samples
4.1(Grade - For MR)	-	500	10% Discount for BIS Samples
7.1.1(Requirements - Open splits, checks or open joints - For Type 1 - Cl. 7.1.1)	-	500	10% Discount for BIS Samples
7.2.1(Requirements - Open splits, checks or open joints - For Type 2 - Cl. 7.2.1)	-	500	10% Discount for BIS Samples
7.1.2(Requirements - Other defects - For Type 1 - Cl. 7.1.2)	-	500	10% Discount for BIS Samples
7.2.2(Requirements - Other defects - For Type 2 - Cl. 7.2.2.)	-	500	10% Discount for BIS Samples
7.1.3(Requirements - Other Charcteristics and Manufacturing Defects - For Type 1 - Cl. 7.1.3)	-	500	10% Discount for BIS Samples
7.2.3(Requirements - Other Charcteristics and Manufacturing Defects - For Type 2 - Cl. 7.2.3)	-	500	10% Discount for BIS Samples
8(Dimensions & Tolerances - Length - Cl. 8)	-	500	10% Discount for BIS Samples
8(Dimensions & Tolerances - Width - Cl. 8)	-	500	10% Discount for BIS Samples
8(Dimensions & Tolerances - Thickness - Cl. 8)	-	500	10% Discount for BIS Samples
8(Dimensions & Tolerances - Edge Straightness - Annexure C)	-	500	10% Discount for BIS Samples
8(Dimensions & Tolerances - Squareness - Annexure C)	-	500	10% Discount for BIS Samples
9(Finish - Cl. 9.1, 8.3)	-	500	10% Discount for BIS Samples
9(Finish - Cl. 9.2, 8.3)	-	500	10% Discount for BIS Samples
11(Tests - Moisture Content - Part 1 of IS 1734)	-	500	10% Discount for BIS Samples
11(Tests - Water Resistance Test - Cl. 11.1.2.1 [for MR Grade])	-	800	10% Discount for BIS Samples
11(Tests - Water Resistance Test - Cl. 11.1.2.2 [for BWR Grade])	-	800	10% Discount for BIS Samples

28 Nov, 2027

-
-

7066

Universal Testing and Research Centre (Division of Sustainable Stewardship Private Limited)

8169306

IS 5509 (2021)

Fire Retardant Plywood - Specification ( Third Revision )

MR, BWR & BWP

10500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.3 (Table 1)(b) 6 mm and above)	-	500	10% Discount for BIS Samples
4.1(Flame retardant chemicals)	-	0	-
4.2(Flame retardant and preservative treatment)	-	0	-
4.3(Treatment)	-	0	-
5(PREPARATION FOR TREATMENT)	-	0	-
6.1.1(Treatment of Plywood by Pressure Impregnation after Manufacture)	-	0	-
6.1.2(Soaking Treatment)	-	0	-
6.2(Choice of Treatment)	-	0	-
7(CONDITIONING AFTER TREATMENT)	-	0	-
8.1(Dimensions)	-	1000	10% Discount for BIS Samples
8.2(Thickness)	-	500	10% Discount for BIS Samples
8.3, Taable-1 (i)(Tolerance- Length)	-	500	10% Discount for BIS Samples
9(WORKMANSHIP AND FINISH)	-	200	10% Discount for BIS Samples
10(SAMPLING AND CRITERIA FOR CONFORMITY)	-	0	-
11 (a)(For flammability)	-	2000	10% Discount for BIS Samples
11 (b)(For flame penetration)	-	2000	10% Discount for BIS Samples
11 (c)(For rate of burning)	-	2200	10% Discount for BIS Samples
12.1 Table - 2 (i)(Moisture content, percent, Max)	-	500	10% Discount for BIS Samples
12.1 Table - 2 (ii)(Flammability (see Note 1), minutes, Min)	-	2000	10% Discount for BIS Samples
12.1 Table - 2 (iii)(Flame penetration (see Note 2), minutes, Min)	-	2000	10% Discount for BIS Samples
12.1 Table - 2 (iv)(Rate of burning (see Note 3), minutes, Min)	-	2200	10% Discount for BIS Samples
12.2(Other Tests)	-	2600	10% Discount for BIS Samples
14(Marking)	-	0	-

28 Nov, 2027

-
-

7067

Universal Testing and Research Centre (Division of Sustainable Stewardship Private Limited)

8169306

IS 4990 (2011)

Plywood for concrete shuttering works - Specification (Third Revision)

BWP & BWR

12800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.0(Types)	-	0	-
7.2(DIMENSIONS & TOLERANCES )	-	500	10% Discount for BIS Samples
7.2(DIMENSIONS & TOLERANCES )	-	500	10% Discount for BIS Samples
7.3(DIMENSIONS & TOLERANCES )	-	500	10% Discount for BIS Samples
7.4(DIMENSIONS & TOLERANCES )	-	500	10% Discount for BIS Samples
7.4(DIMENSIONS & TOLERANCES )	-	500	10% Discount for BIS Samples
8.1(WORKMANSHIP AND FINISH )	-	200	10% Discount for BIS Samples
8.3(WORKMANSHIP AND FINISH )	-	200	10% Discount for BIS Samples
10.1.1(MOISTURE CONTENT)	-	500	10% Discount for BIS Samples
10.1.2, 10.1.2.1 (Table-1)(GLUE ADHESION IN DRY STATE)	-	600	10% Discount for BIS Samples
10.1.2, 10.1.2.2(GLUE ADHESION IN DRY STATE)	-	500	10% Discount for BIS Samples
10.1.3, 10.1.3.1.1 (Table-1)(RESISTANCE TO WATER TEST)	-	500	10% Discount for BIS Samples
10.1.3, 10.1.3.1.2(RESISTANCE TO WATER TEST)	-	600	10% Discount for BIS Samples
10.1.5(MYCOLOGICAL TEST )	-	2600	10% Discount for BIS Samples
10.1.5, 10.1.5.1 (Table-1)(MYCOLOGICAL TEST )	-	2600	10% Discount for BIS Samples
10.1.5.2(MYCOLOGICAL TEST )	-	2600	10% Discount for BIS Samples
10.1.7 (Table-2)(STATIC BENDING STRENGTH)	-	1200	10% Discount for BIS Samples
10.1.7 (Table-2)(STATIC BENDING STRENGTH)	-	1200	10% Discount for BIS Samples
10.1.8 (Table-3)(WET BENDING STRENGTH)	-	1600	10% Discount for BIS Samples
10.1.8 (Table-3)(WET BENDING STRENGTH)	-	1600	10% Discount for BIS Samples
10.1.9(RETENTION OF PRESERVATIVE)	-	2000	10% Discount for BIS Samples
10.1.6(TENSILE STRENGTH)	-	1000	10% Discount for BIS Samples
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Rupture: Across the Face Grain: Minimum Individual))	-	1000	10% Discount for BIS Samples
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Rupture: Across the Face Grain: Average))	-	1000	10% Discount for BIS Samples
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Rupture: Along the Face Grain: Minimum Individual))	-	1000	10% Discount for BIS Samples
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Rupture: Along the Face Grain: Average))	-	1000	10% Discount for BIS Samples
Cl. 10.1.8 (Table 3)(Cl. 10.1.8 (Table 3) (Modulus of Elasticity: Across the Face Grain: Minimum Individual))	-	1000	10% Discount for BIS Samples
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Elasticity: Across the Face Grain: Average))	-	1000	10% Discount for BIS Samples
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Elasticity: Along the Face Grain: Minimum Individual))	-	1000	10% Discount for BIS Samples
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Elasticity: Along the Face Grain: Average))	-	1000	10% Discount for BIS Samples
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Rupture: Across the Face Grain: Minimum Individual))	-	1000	10% Discount for BIS Samples
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Rupture: Across the Face Grain: Average))	-	1000	10% Discount for BIS Samples
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Rupture: Along the Face Grain: Minimum Individual))	-	1000	10% Discount for BIS Samples
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Rupture: Along the Face Grain: Average))	-	1000	10% Discount for BIS Samples
Cl. 10.1.7 (Table 2)(Cl. 10.1.7 (Table 2) (Modulus of Elasticity: Across the Face Grain: Minimum Individual))	-	1000	10% Discount for BIS Samples
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Elasticity: Across the Face Grain: Average))	-	1000	10% Discount for BIS Samples
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Elasticity: Along the Face Grain: Minimum Individual))	-	1000	10% Discount for BIS Samples
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Elasticity: Along the Face Grain: Average))	-	1000	10% Discount for BIS Samples
Cl. 10.1.6(Cl. 10.1.6 (Tensile Strength: Sum of the Tensile Strength in two directions))	-	1000	10% Discount for BIS Samples
Cl. 10.1.6 (Cl. 10.1.6 (Tensile Strength: Perpendicular to grain))	-	1000	10% Discount for BIS Samples
Cl. 10.1.6(Cl. 10.1.6 (Tensile Strength: Parallel to grain))	-	1000	10% Discount for BIS Samples
10.1.9(Chem)(RETENTION OF PRESERVATIVE)	-	2000	10% Discount for BIS Samples
12, 12.1(MARKING)	-	0	ok
12, 12.2(MARKING)	-	0	ok
cl. 10.1.2.1(glue adhesion in dry state - glue shear strength - AVERAGE)	-	1000	10% Discount for BIS Samples
cl. 10.1.2.1(glue adhesion in dry state - glue shear strength - WOOD FAILURE, Average)	-	1000	10% Discount for BIS Samples
cl. 10.1.3.1(resistance to water test - glue shear strength - AVERAGE)	-	2000	10% Discount for BIS Samples
cl. 10.1.3.1(resistance to water test - glue shear strength - WOOD FAILURE, Average)	-	2000	10% Discount for BIS Samples
cl. 10.1.5.1(mycological test - glue shear strength - AVERAGE)	-	2600	10% Discount for BIS Samples
cl. 10.1.5.1(mycological test - glue shear strength - WOOD FAILURE, Average)	-	2600	10% Discount for BIS Samples

28 Nov, 2027

-
-

7068

Universal Testing and Research Centre (Division of Sustainable Stewardship Private Limited)

8169306

IS 710 (2010)

Marine plywood - Specification (Second Revision)

BWP & BWR

12800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1(WORKMANSHIP AND FINISH )	-	200	10% Discount for BIS Samples
7.2(WORKMANSHIP AND FINISH )	-	200	10% Discount for BIS Samples
7.3(WORKMANSHIP AND FINISH )	-	200	10% Discount for BIS Samples
7.5(WORKMANSHIP AND FINISH )	-	200	10% Discount for BIS Samples
6.1(DIMENSIONS)	-	500	10% Discount for BIS Samples
6.1(DIMENSIONS)	-	500	10% Discount for BIS Samples
6.2(DIMENSIONS)	-	500	10% Discount for BIS Samples
6.3(DIMENSIONS)	-	500	10% Discount for BIS Samples
6.3(DIMENSIONS)	-	500	10% Discount for BIS Samples
9.1.1(MOISTURE CONTENT)	-	500	10% Discount for BIS Samples
9.1.2 , 9.1.2.1(Glue Adhesion in Dry State)	-	600	10% Discount for BIS Samples
9.1.2 , 9.1.2.2(Glue Adhesion in Dry State)	-	600	10% Discount for BIS Samples
9.1.3 , 9.1.3.1.1(Water resistance test)	-	500	10% Discount for BIS Samples
9.1.3 , 9.1.3.1.2(Water resistance test)	-	500	10% Discount for BIS Samples
9.1.5(Mycological test)	-	2600	10% Discount for BIS Samples
9.1.5 , 9.1.3.1.1(Mycological test)	-	2600	10% Discount for BIS Samples
9.1.5 , 9.1.3.1.2(Mycological test)	-	2600	10% Discount for BIS Samples
9.1.4(Tensile strength)	-	1000	10% Discount for BIS Samples
9.1.6 (Table 3)(Static bending strength)	-	1200	10% Discount for BIS Samples
9.1.6 (Table 3)(Static bending strength)	-	1200	10% Discount for BIS Samples
9.1.7 (Table 4)(Wet bending strength)	-	1600	10% Discount for BIS Samples
9.1.7 (Table 4)(Wet bending strength)	-	1600	10% Discount for BIS Samples
9.1.8(Retention of preservative)	-	2000	10% Discount for BIS Samples
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Rupture: Across the Face Grain: Minimum Individual))	-	1200	10% Discount for BIS Samples
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Rupture: Across the Face Grain: Average))	-	1200	10% Discount for BIS Samples
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Rupture: Along the Face Grain: Minimum Individual))	-	1200	10% Discount for BIS Samples
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Rupture: Along the Face Grain: Average))	-	1200	10% Discount for BIS Samples
Cl. 9.1.7 (Table 4)(Cl. 9.1.7 (Table 4) (Modulus of Elasticity: Across the Face Grain: Minimum Individual))	-	1200	10% Discount for BIS Samples
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Elasticity: Across the Face Grain: Average))	-	1200	10% Discount for BIS Samples
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Elasticity: Along the Face Grain: Minimum Individual))	-	1200	10% Discount for BIS Samples
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Elasticity: Along the Face Grain: Average))	-	1200	10% Discount for BIS Samples
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Rupture: Across the Face Grain: Minimum Individual))	-	1200	10% Discount for BIS Samples
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Rupture: Across the Face Grain: Average))	-	1200	10% Discount for BIS Samples
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Rupture: Along the Face Grain: Minimum Individual))	-	1200	10% Discount for BIS Samples
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Rupture: Along the Face Grain: Average))	-	1200	10% Discount for BIS Samples
Cl. 9.1.6 (Table 3)(Cl. 9.1.6 (Table 3) (Modulus of Elasticity: Across the Face Grain: Minimum Individual))	-	1200	10% Discount for BIS Samples
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Elasticity: Across the Face Grain: Average))	-	1200	10% Discount for BIS Samples
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Elasticity: Along the Face Grain: Minimum Individual))	-	1200	10% Discount for BIS Samples
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Elasticity: Along the Face Grain: Average))	-	1200	10% Discount for BIS Samples
Cl. 9.1.4(Cl. 9.1.4 (Tensile Strength: Sum of the Tensile Strength in two directions))	-	1000	10% Discount for BIS Samples
Cl. 9.1.4 (Cl. 9.1.4 (Tensile Strength: Perpendicular to grain))	-	1000	10% Discount for BIS Samples
Cl. 9.1.4(Cl. 9.1.4 (Tensile Strength: Parallel to grain))	-	1000	10% Discount for BIS Samples
Cl.9.1.5,9.1.3.1.1(Cl.9.1.5 (Mycological Test),9.1.3.1.1 (Glue Shear Strength: Individual))	-	2600	10% Discount for BIS Samples
Cl.9.1.5,9.1.3.1.1(Cl.9.1.5 (Mycological Test),9.1.3.1.1 ( Glue Shear Strength: Average))	-	2600	10% Discount for BIS Samples
Cl. 9.1.3, 9.1.3.1.1 (Cl. 9.1.3 (Water Resistance Test) , 9.1.3.1.1 (Glue Shear Strength: Individual))	-	600	10% Discount for BIS Samples
Cl. 9.1.3, 9.1.3.1.1 (Cl. 9.1.3 (Water Resistance Test ), 9.1.3.1.1 (Glue Shear Strength: Average))	-	600	10% Discount for BIS Samples
Cl. 9.1.2, 9.1.2.1 (Cl. 9.1.2 (Glue Adhesion in Dry State), 9.1.2.1 ( Glue Shear Strength: Individual))	-	500	10% Discount for BIS Samples
Cl. 9.1.2, 9.1.2.1 (Cl. 9.1.2 (Glue Adhesion in Dry State), 9.1.2.1 ( Glue Shear Strength: Average ))	-	500	10% Discount for BIS Samples
cl.5.1(manufacture - Veneers)	-	1000	10% Discount for BIS Samples
cl.5.1(manufacture - Veneers - moisture content)	-	2000	10% Discount for BIS Samples
cl.5.1.1(manufacture - Veneers - Defects in Veneers)	-	1000	10% Discount for BIS Samples
cl.5.2.2(Assembly - Thickness of Veneers)	-	1000	10% Discount for BIS Samples

28 Nov, 2027

-
-

7069

Universal Testing and Research Centre (Division of Sustainable Stewardship Private Limited)

8169306

IS 303 (1989)

Plywood for General Purposes -

MR & BWR

6500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8(Dimensions & Tolerances - Length - Cl. 8)	-	300	10% Discount For BIS Sample
8(Dimensions & Tolerances - Width - Cl. 8)	-	300	10% Discount For BIS Sample
8(Dimensions & Tolerances - Thickness - Cl. 8)	-	300	10% Discount For BIS Sample
8(Dimensions & Tolerances - Edge Straightness - Annexure C)	-	300	10% Discount For BIS Sample
8(Dimensions & Tolerances - Squareness - Annexure C)	-	300	10% Discount For BIS Sample
9(Workmanship and Finish - Cl.9, 8.3, Annexure C)	-	200	10% Discount For BIS Sample
11.2.1(Glue Adhesion - Water resistance test - 11.2.1.1 [for MR Grade])	-	500	10% Discount For BIS Sample
11.2.1(Glue Adhesion - Water resistance test - 11.2.1.1 [for BWR Grade])	-	500	10% Discount For BIS Sample
11.2.2(Glue Adhesion - Mycological test - 11.2.2, Part 7 of IS 1734 [for MR Garde only])	-	2000	10% Discount For BIS Sample
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Across the Face Grain - Average)	-	1600	10% Discount For BIS Sample
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Across the Face Grain - Minimum Individual)	-	1600	10% Discount For BIS Sample
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Along the Face Grain - Minimum Individual)	-	1600	10% Discount For BIS Sample
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Along the Face Grain - Average)	-	1600	10% Discount For BIS Sample
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Minimum Individual)	-	1600	10% Discount For BIS Sample
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Average)	-	1600	10% Discount For BIS Sample
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Minimum Individual)	-	1600	10% Discount For BIS Sample
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average)	-	1600	10% Discount For BIS Sample
11.3(Moisture Content - Part 1 of IS 1734)	-	500	10% Discount For BIS Sample
5.2, Table 1, Table 2(Quality Requirements - Cl. 5.2)	-	0	ok
5.1(Type - For BB Type)	-	0	ok
5.1(Type - For AB Type)	-	0	ok
5.1(Type - For AA Type)	-	0	ok
4(Grade - For MR grade)	-	0	ok
4(Grade - For BWR grade)	-	0	ok
cl. 13.1(marking)	-	0	ok
cl. 13.2(marking)	-	0	ok

28 Nov, 2027

-
-

7070

JUBILANT PHARMA AND CHEMICAL LAB (OPC) PVT.LTD, NAVI MUMBAI

7169416

IS 14543 (2024)

Packaged Drinking Water Other than Packaged Natural Mineral Water Specification Third Revision

11500.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.3/Table 1/i(Colour)	-	50.00	+ GST
5.3/Table 1/ii(Odour)	-	50.00	+ GST
5.3/Table 1/iii(Taste)	-	50.00	+ GST
5.3/Table 1/iv(Turbidity)	-	50.00	+ GST
5.3/Table 1/v(Total Dissolved Solids)	-	200.00	+ GST
5.3/Table 1/vi(pH)	-	50.00	+ GST
5.3/Table 2/i(Barium)	-	125.00	+ GST
5.3/Table 2/ii(Copper)	-	125.00	+ GST
5.3/Table 2/iii(Iron)	-	125.00	+ GST
5.3/Table 2/iv(Maganese)	-	125.00	+ GST
5.3/Table 2/v(Nitrate)	-	125.00	+ GST
5.3/Table 2/vi(Nitrite)	-	125.00	+ GST
5.3/Table 2/vii(Fluoride)	-	125.00	+ GST
5.3/Table 2/viii(Zinc)	-	125.00	+ GST
5.3/Table 2/ix(Silver)	-	125.00	+ GST
5.3/Table 2/x(Aluminium)	-	125.00	+ GST
5.3/Table 2/xi(Chloride)	-	125.00	+ GST
5.3/Table 2/xii(Selenium)	-	125.00	+ GST
5.3/Table 2/xiii(Suphate)	-	125.00	+ GST
5.3/Table 2/xiv(Alkalinity)	-	125.00	+ GST
5.3/Table 2/xv(Calcium)	-	125.00	+ GST
5.3/Table 2/xvi(Magnesium)	-	125.00	+ GST
5.3/Table 2/xvii(Sodium)	-	125.00	+ GST
5.3/Table 2/xviii(Residual Free Chlorine)	-	125.00	+ GST
5.3/Table 2/xix(Phenolic Compounds)	-	200.00	+ GST
5.3/Table 2/xx(Mineral Oil)	-	350.00	+ GST
5.3/Table 2/xxi(Anionic Surface- Active Agents as MBAS)	-	250.00	+ GST
5.3/Table 2/xxii(Sulphide)	-	125.00	+ GST
5.3/Table 2/xxiii(Antinomy)	-	125.00	+ GST
5.3/Table 2/xxiv(Borates)	-	125.00	+ GST
5.3/Table 2/xxxv(Bromate)	-	500.00	+ GST
5.3/Table 3/i(Mercury)	-	125.00	+ GST
5.3/Table 3/ii(Cadmium)	-	125.00	+ GST
5.3/Table 3/iii(Arsenic)	-	125.00	+ GST
5.3/Table 3/iv(Cyanide)	-	125.00	+ GST
5.3/Table 3/v(Lead)	-	125.00	+ GST
5.3/Table 3/vi(Chromium)	-	125.00	+ GST
5.3/Table 3/vii(Nickel)	-	125.00	+ GST
Cl-5.3, Table-3 (x)(Uranium)	-	500.00	+ GST
5.3/Table 3/viii(Polyclorinated biphenyl (PCB))	-	400.00	Including individual pesticides rate + GST
5.3/Table 3/ix(Polynuclear Aromatic Hydrocarbons)	-	400.00	+ GST
5.4/Annex D/i(P,P-DDT)	-	0.00	NA
5.4/Annex D/ii(Lindane)	-	0.00	NA
5.4/Annex D/iv(b-Endosulfan)	-	0.00	NA
5.4/Annex D/xvi(Dieldrin)	-	0.00	NA
5.4/Annex D/xvi(Aldrin)	-	0.00	NA
5.4/Annex D/i(O,P-DDT)	-	0.00	NA
5.4/Annex D/iv(a-Endosulfan)	-	0.00	NA
5.4/Annex D/iii(d-HCH)	-	0.00	NA
5.4/Annex D/i(O,P-DDD)	-	0.00	NA
5.4/Annex D/i(P,P-DDE)	-	0.00	NA
5.4/Annex D/i(O,P-DDE)	-	0.00	NA
5.4/Annex D/iii(a-HCH)	-	0.00	NA
5.4/Annex D/iii(β- HCH)	-	0.00	NA
5.4/Annex D/iv(Endosulfan sulfate)	-	0.00	NA
5.4/Annex D/i(P,P-DDD)	-	0.00	NA
5.4/Annex D/xii(Alachlor)	-	0.00	NA
5.4/Annex D/vii(Chlorpyrifos)	-	0.00	NA
5.4/Annex D/x(Butachlor)	-	0.00	NA
5.4/Annex D/vi(Ethion)	-	0.00	NA
5.4/Annex D/xiv(Methyl parathion)	-	0.00	NA
5.4/Annex D/xv(Malathion)	-	0.00	NA
5.4/Annex D/viii(Phorate)	-	0.00	NA
5.4/Annex D/v(Monochrotophos)	-	0.00	NA
5.4/Annex D/xiii(Atrazine)	-	0.00	NA
5.4/Annex D/viii(Phorate sulphoxide)	-	0.00	NA
5.4/Annex D/viii(Phorate sulfone)	-	0.00	NA
5.4/Annex D/xxvii(Methyl paraoxon)	-	0.00	NA
5.4/Annex D/xxviii(Malaoxon)	-	0.00	NA
5.4/Annex D/xi(Isoproturon)	-	0.00	NA
5.4/Annex D/ix(2,4 –D)	-	0.00	NA
Cl-5.4 (i)(Pesticide residues considered individually)	-	0.00	NA
Cl-5.4 (ii)(Total pesticide residue)	-	1000.00	+ GST
5.2.1(Escherichia Coli)	-	300.00	+ GST
5.2.2(Coliform)	-	300.00	+ GST
5.2.3(Faecal Streptococci & Staphylococcus aureus)	-	300.00	+ GST
5.2.4(Sulphite Reducing Anaerobes)	-	300.00	+ GST
5.2.5(Pseudomonas aeruginosa)	-	300.00	+ GST
5.2.6(Aerobic Microbial Count @ 22 o C & 37o C)	-	300.00	+ GST
5.2.7(Yeast & Mould)	-	300.00	+ GST
5.2.8(Salmonella & Shigella)	-	300.00	300.00 for Salmonella and 300.00 Shigella + GST
5.2.9(Vibrio Cholera & Vibrio parahaemolyicus)	-	300.00	300.00 for Vibrio cholera and 300.00 vibrio parahaemolyticus + GST

12 Dec, 2027

-
Included w.e.f 03.10.2024 . Exclusion: Cl-5.3, Table-4 (i) (Alpha emitters, Becquerel (Bq/l) and Cl-5.3, Table-4 (ii) Beta emitters, Becquerel (Bq/l)

7071

JUBILANT PHARMA AND CHEMICAL LAB (OPC) PVT.LTD, NAVI MUMBAI

7169416

IS 10500 (2012)

Drinking water - Specification (Second Revision)

Drinking Water

15000.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4. SL No.i)of Table I(Colour)	-	100.00	-
4.SL No.ii) of Table I(Odour)	-	100.00	-
4.SL No.iii)of Table I(pH)	-	100	-
4.SL No.v)of Table I(Turbidity, NTU, Max)	-	100.00	-
4.SL No.vi)of Table I(Total dissolved solids, mg/l, max)	-	200.00	-
table 2 sl.no 1( Aluminium (as Al), mg/l, Max)	-	300.00	-
table 2 sl.no 2(Ammonia (as total ammonia-N), mg/l, Max)	-	400.00	--
table 2 sl.no 3(Anionic detergents (as MBAS), mg/l, Max)	-	300.00	-
table 2 sl.no 4(Barium (as Ba), mg/l, Max)	-	150.00	-
table 2 sl.no 5(Boron (as B), mg/l, Max)	-	200.00	-
table 2 sl.no 6(Calcium (as Ca), mg/l, Max)	-	150.00	-
table 2 sl.no 9(Copper (as Cu), mg/l, Max)	-	300	-
table 2 sl.no 10( Fluoride (as F) mg/l, Max)	-	250.00	-
table 2 sl.no 11(Free residual chlorine, mg/l, Min)	-	250.00	-
table 2 sl.no 12(Iron (as Fe), mg/l, Max)	-	300.00	-
table 2 sl.no 13(Magnesium (as Mg), mg/l, Max)	-	300.00	-
table 2 sl.no 14(Manganese (as Mn), mg/l, Max)	-	300.00	-
table 2 sl.no 15(Mineral oil, mg/l, Max)	-	400.00	-
table 2 sl.no 16(Nitrate (as NO3), mg/l, Max)	-	300.00	--
table 2 sl.no 17(Phenolic compounds (as C6H5OH), mg/l, Max)	-	300.00	-
table 2 sl.no 18(Selenium (as Se), mg/l, Ma)	-	300.00	--
table 2 sl.no 19(Silver (as Ag), mg/l, Max)	-	300	300.00
table 2 sl.no 20(Sulphate (as SO4) mg/l, Max)	-	250.00	--
table 2 sl.no 21(Sulphide (as H2S), mg/l, Max)	-	250.00	-
table 2 sl.no 22(Total alkalinity as calcium carbonate, mg/l, Max)	-	150.00	--
table 2 sl.no 23(Total hardness (as CaCO3 mg/l, Max)	-	150.00	-
table 2 sl.no 24(Zinc (as Zn), mg/l, Max)	-	300.00	--
TABLE 3 sl no 1(Cadmium (as Cd), mg/l, Max)	-	300.00	--
TABLE 3 sl no 2(Cyanide (as CN), mg/l, Max)	-	350.00	-
TABLE 3 sl no 3(Lead (as Pb), mg/l, Max)	-	300.00	-
TABLE 3 sl no 4(Mercury (as Hg), mg/l, Max)	-	300.00	--
TABLE 3 sl no 5( Molybdenum (as Mo), mg/l, Max)	-	300.00	-
TABLE 3 sl no 6(Nickel (as Ni), mg/l, Max)	-	300.00	--
TABLE 3 sl no 7(Pesticides, µg/l, Max)	-	1000.00	-
TABLE 3 sl no 8(Polychlorinated biphenyls, mg/l,)	-	500.00	--
TABLE 3 sl no 9(Polynuclear aromatic hydro-carbons (as PAH), mg/l, Max)	-	500.00	--
TABLE 3 sl no 10(Total arsenic (as As), mg/l, Max)	-	300.00	--
TABLE 3 sl no 11(Total chromium (as Cr), mg/l, Max)	-	300.00	--
TABLE 3 sl no 12(Bromoform, mg/l, Max)	-	400.00	-
TABLE 3 sl no 13(Dibromochloromethane,)	-	400.00	-
TABLE 3 sl no 14(Dibromochloromethane,mg/l, Max)	-	400.00	-
TABLE 3 sl no 15(Chloroform, mg/l, Max)	-	500.00	-
TABLE 5 sl no 1(Alachlor)	-	0.00	-
TABLE 5 sl no 2(Atrazine)	-	0.00	-
TABLE 5 sl no 4( Alpha HCH)	-	0.00	-
TABLE 5 sl no 5(Beta HCH)	-	0.00	-
TABLE 5 sl no 6(Butachlor)	-	0.00	-
TABLE 5 sl no 7(Chlorpyriphos)	-	0.00	-
TABLE 5 sl no 8(Delta HCH)	-	0.00	-
TABLE 5 sl no 9(2,4- Dichlorophenoxyacetic acid)	-	0.00	-
TABLE 5 sl no 10( DDT (o, p and p, p – Isomers of DDT, DDE and DDD))	-	0.00	-
TABLE 5 sl no 11(Endosulfan (alpha, beta, and sulphate))	-	0.00	-
TABLE 5 sl no 12( Ethion)	-	0.00	-
TABLE 5 sl no 13(Gamma — HCH (Lindane))	-	0.00	-
TABLE 5 sl no 14( Isoproturon)	-	0.00	-
TABLE 5 sl no 15(Malathion)	-	0.00	-
TABLE 5 sl no 16(Methyl parathion)	-	0.00	-
TABLE 5 sl no 17(Monocrotophos)	-	0.00	-
TABLE 5 sl no 18(Phorate)	-	0.00	-
TABLE 6 sl no 1(All water intended for drinking: a) E. coli or thermotolerant coliform bacteri)	-	400.00	-
TABLE 6 sl no 2(Treated water entering the distribution system: a) E. coli or thermotolerant coliform bacteria)	-	400.00	-
TABLE 6 sl no 3(b) Total coliform bacteria)	-	400.00	-
4, Table 2, Sr. no. vii(Chloramines)	-	500.00	-
4, Table 2, Sr.no. viii(Chloride)	-	150.00	-
Table 5(Aldrin and Dieldrin )	-	0.00	--
Table 1 clause(iv)(Taste)	-	500.00	-
Table 3, x)(Uranium)	-	500.00	-

12 Dec, 2027

-
-

7072

CIPET, Lucknow

9102534

IS 15450 (2022)

Polyethylene-aluminium-polyethylene composite pressure pipes for hot and cold water supplies Specifications first revision of IS 15450

PE 80, 12mm to 75mm

39538 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.3.1(UV Stabilizer)	-	2000	NIL
5.4(Aluminium)	-	1800	Tensile 1300+Specimen 500
8(COLOUR)	-	500	NIL
9(DIMENSIONS OF PIPE)	-	500	NIL
9.3(Length of Straight Pipe)	-	0	NIL
9.4(Coiling)	-	0	NIL
10(VISUAL APPEARANCE)	-	500	NIL
11.1(Density (Method of test as per Table 3))	-	700	NILNIL
11.2(Melt Flow Rate (Method of test as per Table 3))	-	1100	NIL
11.3(Overall Migration)	-	1700	Specimen/conditioning charge-625
11.4(Thermal Stability to Oxidation (Method of test as per Table 3))	-	2200	NIL
11.5(Carbon Black Content and Dispersion (Method of test as per Table 3))	-	1625	CBC 925 CBD 700
11.6(Pigment Dispersion (For Coloured Pipes) (Method of test as per Table 3))	-	700	NIL
11.7(Resistance to Weathering)	-	36000	NIL
11.8(Adhesion Test)	-	1100	NIL
11.9(Apparent Tensile Strength of Pipe)	-	1100	Specimen/Conditioning charge-500
11.10(Minimum Burst Pressure)	-	1000	NIL
11.11(Hydraulic Characteristics)	-	2700	NIL
5(MATERIALS)	-	0	Nil
6(PRESSURE RATING)	-	0	Nil
7(NOMINAL DIAMETERS)	-	0	Nil
14(MARKING)	-	0	Nil
9.2.1(Method of Measurements)	-	0	Nil
11.11.1(Short Term Hydrostatic Tests)	-	0	Nil
11.11.12(Long Term Hydrostatic Test)	-	0	Nil

31 Dec, 2026

-
Exclusion : Tsble 3 (Antioxidant) Cl 5.0 (5.1, 5.2.1, 5.2.1.1)

7073

CIPET, Lucknow

9102534

IS 15827 (2019)

Cladding films for greenhouse / polyhouse - Specifications (First Revision)

1888125 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Material Identification)	-	2000	NIL
6.1(Appearance & surface finish)	-	500	NIL
6.2(Durability ref clause No. 7.5)	-	0	Exposure charges are extra with full testing charge 13088 as per requirements.
7.1(Visual)	-	500	NIL
Cl. no. 6.3 & Table 2(Tensile strength & elongation at break (TD & MD))	-	3100	TD 1300 MD 1300 Specimen 500
6.3(Dart Drop test)	-	1100	NIL
6.3(Total Visible Light Transmittance)	-	700	NIL
6.3(Haze)	-	700	NIL
6.3(Tear Strength ( MD & TD))	-	2700	TD 1100 MD 1100 Specimen 500
7.4(IR eefectiveness)	-	2500	NIL
7.2(width)	-	500	NIL
7.3(Elongation under Steady Load MD)	-	0	added in tensile charges
7.5(Elongation after UV Exposure MD)	-	0	added in tensile charges

31 Dec, 2026

-
-

7074

CIPET, Lucknow

9102534

IS 14885 (2022)

Polyethylene Pipes for the Supply of Gaseous Fuels ï¿½ Specification (First Revision)

PE-80, PE-100, 16mm to 500mm

402000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.4(Colour)	-	500	NIL
5.6(Resistance to Weathering)	-	36000	NIL
7(Finish)	-	5005	NIL
8.1(Internal pressure creep rupture test for plain pipes at 20 deg. C for 100h)	-	11000	NIL
8.1(Internal pressure creep rupture test for plain pipes at 80 deg. C for 1000 h)	-	4800	NIL
8.2(Reversion Test)	-	700	NIL
8.6(Thermal Stability (Oxidation Induction Time))	-	2200	NIL
8.7(Volatile Matter Content)	-	700	NIL
8.3(Density)	-	500	NIL
8.4(Melt Flow Rate (MFR))	-	1100	NIL
5.3(Anti-oxidant)	-	0	NIL
5.4(U-V stabilizer)	-	0	NIL
5.1, 5.7 Table 2(i) Conventional density (of base polymer))	-	500	NIL
5.1, 5.7 Table 2(ii) Melt flow rate (MFR))	-	1100	NIL
5.1, 5.7 Table 2(iii) Thermal stability (oxidation induction time))	-	2200	NIL
5.1, 5.7 Table 2(iv) Volatile content)	-	700	NIL
4.3(Nominal Diameter)	-	500	NIL
5.1(Polyethylene compound)	-	500	NIL
5.7(PE Compound Quality Evaluation)	-	0	NIL
5.5(Effect of Gas condensate on the Hydrostatic strength)	-	5000	Chemical charges extra or provided by party
6.1(Mean out side Diameter (For less than or equal to 25 mm- Average of 8 , For higher diameters average of 6))	-	500	NIL
6.1(Out of Roundness (Ovality))	-	0	NIL
6.2(Wall thickness (Take 8 reading and Average will be repoted))	-	500	NIL
8.1(Internal pressure creep rupture test for plain at 80 deg. C for 165h)	-	15500	Type and acceptance test
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	1800	Test charges 1300 + specimen charges 500
8.9(Resistance to Weathering)	-	0	NIL
6.4(Length of Pipe)	-	500	NIL
8.5(Pigment Dispersion)	-	700	NIL
8.10(Slow Crack Growth Rate Test)	-	10800	Type & acceptance test
8.11(Squeeze-off)	-	1300	NIL
10(Marking)	-	500	NIL
5.1, 5.7 Table 2(v) Water content1))	-	700	NIL
5.1, 5.7 Table 2(vi) Pigment dispersion)	-	700	NIL
5.1, 5.7 Table 3(iv) Resistance to slow crack growth rate)	-	0	charge added above

31 Dec, 2026

-
Exclusion : Cl 5.3 (Anti oxidant) Cl 5.4 ( UV Stabilizer)

7075

CIPET, Lucknow

9102534

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

20-500mm

34031 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.2(Colour)	-	500	NIL
Cl-7.4(Mean Outside Diameter (For upto 50 mm take 8 reading, above 50mm take 6 reading & average will be reported))	-	500	NIL
6.2.1(6.1.1 Identification Stripes)	-	1050	NIL
8,/8.1/8.1.1 table-5(PERFORMANCE REQUIREMENTS / Hydraulic Characteristics/ Internal Pressure Creep Rupture Test of Pipe)	-	21400	a) Hyd. Test - 48 hrs. b) Hyd.Test - 100 hrs c) Hyd.Test - 1000 hrs d) Hyd.Test - 165 hrs.
8.1.2 table -5(Internal Pressure Creep Rupture Test of Pipe Joints)	-	1600	NIL
8.2(Longitudinal Reversion Test)	-	1200	Test charges 700 + specimen charges 500
8.6(Overall migration)	-	2000	NIL
8.7(Density)	-	700	NIL
8.4( Melt Flow Rate)	-	1100	NIL
8.5 (Oxidation Induction Time)	-	2200	NIL
8.8(Tensile Strength for Butt-fusion)	-	1800	Test charges 1300 + specimen charges 500
8.9 table-6(Elongation at Break)	-	0	Charge added in tensile test
8.10(Slow Crack Growth Rate)	-	6000	Test charges 5500 + specimen charges 500
8.3(Carbon black)	-	925	NIL

31 Dec, 2026

-
-

7076

CIPET, Lucknow

9102534

IS 12818 (2010)

Unplasticized polyvinyl chloride (Pvc - U) screen and casing pipes for bore/tubewells - Specification (Second Revision)

9825 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Max)	-	1000	NIL
8.1 to 8.3 and Table 11 &12 Fig 3A & 4A(THREADING OF SCREEN ANDCASING PIPES. IS 554.)	-	500	NIL
8.4(Sealing elements a. Elastomeric material b. Shore A hardness of sealing Elements )	-	500	NIL
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	500	NIL
9.1( Visual Appearance)	-	500	NIL
9.3(Density IS 12235 (Part 14))	-	700	NIL
9.4 and Table 14(Resistance to External Blows at 0 ?C IS 12235 (Part 9))	-	1500	test charges 1000 + specimen 500
9.5(Tensile Strength IS 12235(Part 13))	-	1800	test charges 1300 + specimen 500
9.6(Vicat Softening Temperature IS 12235 (Part 2).)	-	1100	NIL
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Min)	-	0	NIL
7.1, 7.2 and Table 5, 6 & 7 Fig 1B(Mean outside dia over connection,mm (Take 4 reading and maximum valu reported))	-	0	NIL
7.1, 7.2 and Table 5, 6 & 7 Fig 1B(Outer Diameter at any point, Max)	-	0	NIL
7.1, 7.2 and Table 5, 6 & 7 Fig 1B(Outer Diameter at any point , Min)	-	0	NIL
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter of Pipe , Max)	-	0	NIL
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter of Pipe, Min)	-	0	NIL
7.2 and Table 5, 6 & 7 Fig 1B(Nominal Diameter)	-	0	NIL
7.4 Table 8 & 9 Fig 1(Segmental length for Spigot (average of 4.0))	-	0	NIL
7.4 Table 8 & 9 Fig 1(Segmental length,mm for socket (average of 4.0))	-	0	NIL
7.4 Table 8 & 9 Fig 1(Segmental length, l3)	-	0	NIL
7.4 Table 8 & 9 Fig 1(Effective length, l2)	-	0	NIL
9.2(Internal Diameter)	-	500	NIL
9.7(Effect on Water a) Lead (first extraction) b) Lead (Third extraction) c) Dialkyl Tin C4 & higher homologues measured as Tin (Third extraction) d) Cadmium (All three extracts) e) Mercury (All three extracts) f) Other Toxic Substances )	-	3000	NIL
5.0(Colour of Pipes)	-	500	NIL
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Wall thickness)	-	0	NIL
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Mean Outer Diameter over Connection)	-	0	NIL
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Outer Diameter at any point )	-	0	NIL
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Mean Outer Diameter of Pipe)	-	0	NIL
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Nominal Diameter)	-	0	NIL
7.3.1(No.of Ribs)	-	0	NIL
7.3.2(Rib height)	-	0	NIL
7.5.1 7.5.2 (Slot Dimension (Table 10) Fig 2A & 2B a. Minimum number of slot on the circumference b. Σa±5% c. Mean value of approximate free passage area (%) for width of slot (w) d. Tolerance on width of slot (w) e. Width of material between slot (b))	-	0	NIL
8.3.1 & 8.3.2 (Threading of casing pipe (from 100 to 200 DN Table – 11 & Fig. 3A) & (from 250 to 400 DN Table – 12 & Fig. 4A) Outside diameter d1(+0, -0.3) d2 d3 D1 (+0.3, -0) D2 D4 D5 (+0.3, -0) Z h3 (+0, -0.1) H4 (+0, -0.1) )	-	500	NIL
4.1.2(K-Value as per IS-4669)	-	1100	NIL
4.1.1 (VCM Content as per IS 10151 (Annex A))	-	3000	NIL

31 Dec, 2026

-
-

7077

CIPET, Lucknow

9102534

IS 13592 (2013)

Unplasticized Polyvinyl Chloride (PVC-U) Pipes for Soil and Waste Discharge System Inside and Outside Buiildings Including Ventilation and Rainwater System

Type - A & B

16788 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.5(Surface colour of the pipes shall be dark shade of grey)	-	500	NIL
Cl. 12, IS 12235 Part 11(Resistance to Di-Chloro-Methane)	-	1000	NIL
Cl.7.1(Mean out side Diameter (For less than or equal to 40 mm- Average of 8 , For higher diameters up to 110 mm average of 6))	-	500	NIL
Cl.7.1(Outside Diameter at any point (Take 8 reading reported minimum, maximum))	-	0	NIL
Cl.7.1(Wall thickness "minimum,maximum" (Take 8 reading))	-	0	NIL
Cl.7.2(Pipes shall be supplied in nominal lengths of 2, 3, 4 or 6 metres either plain or with socket for solvent cementing/grooved socket. Tolerances on specified length shall be + 10 mm and – 0 mm.The nominal length of the pipe with socket for solvent cementing/grooved socket shall be as given in Fig. 1.)	-	0	NIL
Cl.7.3.1(Minimum wall thickness of socket on pipes shall be as given in Table 2 read with Fig. 2 and Fig. 3.)	-	0	NIL
Cl.7.3.2(Dimensions of sockets for solvent cementing and grooved sockets of pipes shall be as given in Tables 3 and 4 respectively, read with Fig. 2 and 3.)	-	500	NIL
Cl.8.1(The internal and external surface of the pipes shall be smooth and clean, and free from grooving and other defects. The end shall be clearly cut and shall be square with the axis of the pipe. The end may be chamfered on the plain side.)	-	500	NIL
Cl.8.2(When tested by the method described in IS 12235 (Part 5), a length of pipe sample of 200 ± 20 mm shall not alter in length by more than 5 percent. In the case of socket ended pipes, this test shall be carried out on the plain portion of pipe taken at least 100 mm away from the root of the socket.)	-	1200	Test charge (700) + Specimen charge(500)
Cl8.3(This test shall be carried out for socket end pipes only. When tested by the method described in IS 12235 (Part 6), the test specimens shall not show blisters, excessive delamination or cracking or signs of weld line splitting.)	-	700	NIL
Cl.8.4(When determined in accordance with IS 12235 (Part 2), the vicat softening temperature of the specimen shall not be less than 79°C.)	-	1100	NIL
Cl.8.5(After the required period of exposure, the tensile strengths of two samples when tested as per IS 12235 (Part 13) shall not show difference of more than 20 percent of their initial tensile strengths)	-	3500	NIL
Cl. 9, IS 12235 Part 7(Resistance to Sulphuric Acid)	-	2500	NIL
Cl.10.1(When tested by method prescribed in IS 12235 (Part 9),the pipe shall have a true impact rate of not more than 10 percent. Mass of striker and height of fall shall be as per Annex A.)	-	1600	test charges (1100) + Specimen charge (500)
Cl.10.2(When determined in accordance with the method described in IS 12235 (Part 13), the tensile strength at break shall not be less than 45 MPa.)	-	1800	test charge (1300) + Specimen charge (500)
Cl.10.3(The axial shrinkage shall not exceed 2 percent when determined in accordance with Annex B.)	-	700	NIL
Cl.11.(Jointing of solvent cementing joints is to be carried out using solvent conforming to IS 14182. Apply a pressure of 0.05 MPa for a period of 15 min and there should be no leakage at any joint.)	-	1000	NIL
8.6(Effect on Water Test)	-	3000	NIL

31 Dec, 2026

-
-

7078

CIPET, Lucknow

9102534

IS 15778 (2007)

Chlorinated polyvinyl chloride (Cpvc) pipes for potable hot and cold water distribution supplies - Specification

15-175mm

140438 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1 IS 12235 (Part 1) Table 2(Dimension of Pipes: Mean outside Diameter)	-	500	NIL
9.1(Visual Appearance)	-	500	NIL
9.2 IS 12235 (Part 3)(Opacity)	-	700	NIL
9.4 IS 12235(Part 5/Sec 1 and Sec 2)(Reversion Test : When tested by the method prescribed in IS 12235(Part 5/Sec 1 and Sec 2), a length of pipe 200 + 20 mm long shall not alter in length by more than 5 percent.)	-	700	NIL
9.5 IS 12235(Part 2)(Vicat Softening Temperature: When tested by the method prescribed in IS 12235(Part 2), the Vicat softening temperature of the specimen shall not be less than 110°C.)	-	1100	NIL
9.6 IS 12235(Part 14)(Density)	-	700	NIL
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	16650	a) Acceptance Test - 1 hr/27 C b) Type Test - 95 C/165 hrs c) Type test - 95 C/1000 hrs.
10.2 Table 3 IS 12235 (Part 8/Sec 1)(Thermal Stability by Hydrostatic Pressure Testing)	-	110500	NIL
10.3 IS 4985 Table 4(Resistance to External Blow at O°C: When tested by the method prescribed in IS 4985, with classified striker mass and drop height as given in Table 4, the pipe shall have a true impact rate of not more than 10 percent.)	-	1600	test charges 1100 + specimen 500
10.4 IS 12235(Part 19)(Flattening Test)	-	500	NIL
10.5 IS 12235(Part 13)(Tensile Strength : When tested by the method prescribed in IS 12235(Part 13), the tensile strength at yield shall not be less than 50 MPaat 27±2°C. )	-	1800	test charges 1300 + specimen 500
6.3.2 Annex C(Verification of the Malfunction Temperature, Tmal: )	-	11300	NIL
7.1.2(Wall Thickness (Maximum))	-	0	NIL
7.1.1(Outside Diameter at any point (Maximum))	-	0	NIL
7.1.2 IS 12235 (Part 1)Table 2(Wall Thickness (Minimum))	-	0	NIL
7.1,7.1.1 IS 12235 (Part 1)Table 2(Outside Diameter at any point (Minimum))	-	0	NIL
Cl. 9.3,IS 4985 Cl. 10.3(Lead (first extraction))	-	3000	NIL
Cl. 9.3,IS 4985 Cl. 10.3(Lead (third extraction))	-	0	NIL
Cl. 9.3,IS 4985 Cl. 10.3(Dialkyl tin C4 and higher homologues measured as tin (third extraction))	-	0	NIL
Cl. 9.3,IS 4985 Cl. 10.3(Cadmium (for all three extracts) )	-	0	NIL
Cl. 9.3,IS 4985 Cl. 10.3(Mercury (for all three extracts) )	-	0	NIL
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances such as 'di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate' (third extraction) )	-	0	NIL
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances including di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate')	-	0	NIL
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	0	NIL
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	0	NIL
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	0	NIL

31 Dec, 2026

-
-

7079

CIPET, Lucknow

9102534

IS 15801 (2008)

Polypropylene - Random copolymer pipes for hot and cold water supplies - Specification

16-200mm

108644 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 7(Dimensions Of Pipes)	-	500	NIL
Cl 8(Visual Appearance)	-	500	NIL
Cl 9.1(Hydraulic Characteristics)	-	18500	Acceptance & Type test
Cl 9.2(Fusion Compatibility)	-	4800	NIL
Cl 9.3(Reversion Test )	-	1200	test charges 700 + specimen charges 500
Cl 9.4 & Annex B(Impact Strength)	-	1600	test charges1100 + specimen charges 500
Cl 9.5(Density)	-	700	NIL
Cl 9.6(Melt Flow Rate)	-	1100	NIL
Cl 9.7(Carbon Black Content & Dispersion)	-	1625	NIL
Cl 9.8(Thermal Stability By Hydrostatic Pressure Testing)	-	83825	NIL
Cl 9.9(Opacity)	-	700	NIL

31 Dec, 2026

-
-

7080

CIPET, Lucknow

9102534

IS 12701 (1996)

Rotational moulded polyethylene water storage tanks - specification (First Revision)

All

14156 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2.3(Carbon Black Content )	-	925	NIL
4.2.3(Carbon Dispersion Test)	-	700	NIL
5.4(Wall Thickness above effective height)	-	500	a) Wall Thickness upon effective height b) Wall Thickness upon effective height
6.1(Finish)	-	500	Visual Appearance
7.1.1(Resistance to Deformation)	-	700	NIL
7.2(Resistance to Impact)	-	1000	NIL
7.4(Tensile Strength)	-	1800	Test charges 1300 + specimen 500
7.5(Flexural Modulus)	-	1600	Test charges 1100 + specimen 500
7.6(overall Migration)	-	2200	Test in water & Acetic Acid
9.1(Man-Hole and Hand-Hole Lids)	-	0	NIL
9.1(Lid Thickness)	-	500	NIL
9.2(Man-Hole and Hand-Hole Lids)	-	500	Lid lockup

31 Dec, 2026

-
-

Bureau of Indian Standards

The National Standards Body of India

Search by IS Number