BIS - LIMS (Laboratory Information Management System)

Search by IS Number

Reset

15623 Results

S.No.

Lab Name

Osl Code

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

7531

URS PRODUCTS AND TESTING PVT. LTD. (A29), NOIDA

8168906

IS 15298 : Part 3 (2024)

Personal Protective Equipment Part 3 Protective Footwear (ISO 20346 : 2021, MOD) (Third Revision)

Personal Protective Equipment Part 3 Protective Footwear

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5.2(Design)	-	100	-
Cl 5.2.2(" Height of upper ")	-	250	-
Cl 5.2.3(Heel area)	-	500	-
Cl 5.3.1.1(Construction of whole footwear)	-	500	-
Cl 5.3.1.2(Upper/outsole bond strength)	-	600	-
Cl 5.3.2.1(Toe protection - general)	-	600	-
Cl 5.3.2.2(Internal length)	-	600	-
Cl 5.3.2.3(Width of toecap flange)	-	600	-
Cl 5.3.2.4.1(Corrosion resistance of Class I footwear and hybrid mounted footwear)	-	600	-
Cl 5.3.2.4.2(Corrosion resistance of Class II and hybrid moulded footwear)	-	600	-
Cl 5.3.2.5(Behaviour of toecaps (thermal and chemical) of Corrosion resistance)	-	600	-
Cl 5.3.2.6(Impact resistance)	-	1000	-
Cl 5.3.2.7(Compression resistance)	-	1000	-
Cl 5.3.3(Leak proofness)	-	800	-
Cl 5.3.4("Specific ergonomic features ")	-	600	-
Cl 5.3.5.2(Slip resistance on ceramic tile floor with sodium lauryl sulphate (NaLS) solution)	-	1000	-
Cl 5.3.6, Table no 1 of IS 17011 (i)(Allergenic and carcinogenic disperse dyes)	-	2500	-
Cl 5.3.6, Table no 1 of IS 17011 (ii)(Aromatic amines released from Azo dyes (each individual amine))	-	2500	-
Cl 5.3.6, Table no 1 of IS 17011 (iii)(Aromatic amines released from Azo dyes (each individual amine))	-	2500	-
Cl 5.3.6, Table no 1 of IS 17011 (iv)(Chromium (VI))	-	1200	-
Cl 5.3.6, Table no 1 of IS 17011 (v)(Dimethyl fumarate (DMFU))	-	2500	-
Cl 5.3.6, Table no1 of IS 17011 (vi)(Formaldehyde (free or released by partial hydrolysis))	-	1200	-
Cl 5.3.6, Table no 1 of IS 17011 (vii)(Formaldehyde)	-	2500	-
Cl 5.3.6, Table no 1 of IS 17011 (viii)(Organotin compounds)	-	2500	-
Cl 5.3.6, Table no 1 of IS 17011 (ix)(PCP-TeCP-TriCP polychlorophenols)	-	2500	-
Cl 5.3.6, Table no 1 of IS 17011 (x)(pH)	-	600	-
Cl 5.3.6, Table no 1 of IS 17011 (xi)(Phthalates (each individual phthalate))	-	2500	-
Cl 5.3.6, Table no 1 of IS 17011 (xii)(Nickel, on skin contact)	-	2500	-
Cl 5.3.7(Seam strength)	-	600	-
Cl 5.3.8(Lead Content ( National Annex A))	-	1000	-
Cl 5.4.1.1(Class I footwear, determination of the area where upper requirements apply of Upper)	-	600	-
Cl 5.4.1.2(Hybrid footwear, determination of the area where upper requirements apply of Upper)	-	600	-
Cl 5.4.2(Thickness)	-	250	-
Cl 5.4.3(Tear strength)	-	600	-
Cl 5.4.4, Table 11(Tensile properties- Tensile strength)	-	600	-
Cl 5.4.4, Table 11(Tensile properties- Breaking Force)	-	600	-
Cl 5.4.4, Table 11(Tensile properties-Modulus at 100 % elongation)	-	600	-
Cl 5.4.4, Table 11(Tensile properties- Elongation at break)	-	600	-
Cl 5.4.4, Table 11(Tensile properties- Elongation at break)	-	600	-
Cl 5.4.6(Water vapour permeability and coefficient)	-	800	-
Cl 5.4.7(Resistance to hydrolysis)	-	1000	-
Cl 5.5.2(Lining- Tear strength)	-	600	-
Cl 5.5.3(Lining- Abrasion resistance)	-	800	-
Cl 5.5.4(Lining-Water vapour permeability and coefficient)	-	800	-
Cl 5.6.2(Tear strength of tongue)	-	600	-
Cl 5.7.1(Thickness of Insole, insock and footbed)	-	600	-
Cl 5.7.2(Water permeability of insock)	-	800	-
Cl 5.7.3(Water absorption and desorption of Insole, insock and footbed)	-	800	-
Cl 5.7.4.1(Abrasion resistance of Insoles)	-	800	-
Cl 5.7.4.2(Abrasion resistance of Insocks)	-	800	-
Cl 5.8.2.1(Thickness of Outsole)	-	600	-
Cl 5.8.2.2(Cleated area)	-	600	-
Cl 5.8.2.3(Cleat height)	-	600	-
Cl 5.8.3(Outsole- Tear strength)	-	600	-
Cl 5.8.4(Outsole- Abrasion resistance)	-	800	-
Cl 5.8.5(Outsole-Flexing resistance)	-	800	-
Cl 5.8.6(Outsole-Resistance to hydrolysis)	-	1000	-
Cl 5.8.7(Interlayer bond strength)	-	600	-
Cl 6.2.1.1.2(Metallic perforation-resistant inserts (Type P))	-	600	-
Cl 6.2.1.1.3(Non-metallic perforation-resistant inserts and insoles (Type PL))	-	600	-
Cl 6.2.1.1.4(Non-metallic perforation-resistant inserts and insoles (Type PS))	-	600	-
Cl 6.2.1.2(Construction of perforation resistant insert)	-	600	-
Cl 6.2.1.3(Dimensions of perforation resistant insert)	-	600	-
Cl 6.2.1.4.1(Flex resistance of perforation-resistant inserts)	-	800	-
Cl 6.2.1.4.2.1(Corrosion resistance of perforation resistant metallic insert for Class I footwear and hybrid mounted footwear)	-	600	-
Cl 6.2.1.4.2.2(Corrosion resistance of perforation resistant metallic insert for Class II footwear and hybrid moulded footwear)	-	600	-
Cl 6.2.1.4.3(Stability against ageing and environmental influence of non-metallic perforationresistant inserts)	-	1000	-
Cl 6.2.2.1(Electrical properties of Partially conductive footwear)	-	2500	-
Cl 6.2.2.2(Electrical properties of Antistatic footwear)	-	2500	-
Cl 6.2.3.1(Heat insulation of outsole complex)	-	1000	-
Cl 6.2.3.2(Cold insulation of outsole complex)	-	1000	-
Cl 6.2.4(Energy absorption of seat region)	-	1000	-
Cl 6.2.5(Water resistance)	-	1000	-
Cl 6.2.8.2(Cut resistance footwear- design)	-	1500	-
Cl 6.2.8.2(Dimensions and construction of protective area of Cut resistance footwear)	-	600	-
Cl 6.2.8.3(Resistance to cutting)	-	1500	-
Cl 6.2.9(Scuff cap)	-	800	-
Cl 6.2.10("Slip resistance on ceramic tile floor with glycerine ")	-	1000	-
Cl 6.3(Upper — Water penetration and absorption)	-	800	-
Cl 6.4.1(Resistance to hot contact - Outsole)	-	1000	-
Cl 6.4.2(Resistance to fuel oil - Outsole)	-	1000	-
Cl 6.4.3.1(Mechanical properties of Ladder grip)	-	800	-
Cl 6.4.3.2(Design of Ladder grip)	-	800	-
Cl 6.4.3.3(Cleat height in the waist area of Ladder grip)	-	800	-
Cl 6.4.3.4(Heel breast of Ladder grip)	-	800	-
Cl 7("Marking ")	-	100	-
Cl 7("Marking ")	-	100	-

-
Included w.e.f. 17.02.2025 Exclusion: Cl 6.2.6.1 (Metatarsal protection - Construction), Cl 6.2.6.2 ("Metatarsal protection-Impact resistance of metatarsal protective device "), Cl 6.2.7 (Ankle protection)

7532

BIS, Central Laboratory (CL)

None

IS 9873 : Part 9 (2017)

Safety of Toys Part 9 Certain Phthalates Esters in Toys and Children's Products

4600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.0 (Vinyl in toys or childcare articles - a) Bis-(2-ethlyhexyl) Phthalates (DEHP), b) Di-Butyl phthalate (DBP), c) Benzyl butyl Phthalate (BBP) - IS 9873 Part 6)	-
3.0 (Vinyl in any part of the toy or childcare article that can be placed in mouth of a child under 4 years of age - a) Di-iso-Nonyl Phthalate (DINP), b) Di-iso-Decyl Phthalate (DIDP), c) Di-n-Octyl Phthalate (DNOP) - IS 9873 Part 6)	-

-
2 piece

7533

Bharat Test House Pvt. Ltd. 1668 Sonipat

9168306

IS 16098 Part 2 (2013)

Structured-Wall Plastics Piping Systems for Non-Pressure Drainage and Sewerage Part 2 Pipes and Fittings with Non-Smooth External Surface, Type B

75000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1.1 Table-10 (i)(Ring Stiffness)	-	5000	-
Table -1 Cl. No. 5.1, i)(Base Density)	-	0	-
Table -1 Cl. No. 5.1, ii)(Melt Flow Rate (MFR) at (190ºC, 5kg load))	-	5000	-
Table -1 Cl. No. 5.1, iii)(Thermal Stability (Oxidation Induction Test, OIT) at 200ºC)	-	0	-
8.1.1 Table-10 (ii)(Impact Strength at (0±1 ºC))	-	5500	-
" 5.1 Table-2 ", i)(Resistance to Internal Pressure 165hrs)	-	5500	-
" 5.1 Table-2 ", ii)(Resistance to Internal Pressure 1000hrs)	-	5500	-
8.1.1, 8.1.2 Table-10 (iii)(Ring flexibility 30% of dem)	-	5000	-
6.3.1 & Table-5(Dim (min.) E4 (min) E5 (min.) Socket Length)	-	1000	-
6.3.2(Length of Pipe)	-	1000	-
8.1.1 Table-10 (iv)(Creep ratio)	-	3500	-
6.3.3(Out Side Diameter)	-	1000	-
6.3.5.1.1(Ring Stiffness of Spigot + socket)	-	5000	-
"6.3.5.1.5 Table-5 "(Socket thickness Avg. (min.) Avg.)	-	1000	-
9 Table-12 (i)(Tightness of elastomeric ring seal Joint)	-	4500	-
6.3.5.2(Wall Thickness(e4 min))	-	1000	-
9 Table 12 (ii)(Water tightness)	-	1000	-
6.3.5.2("Construction Height of body wall(ec) Wall Thickness (emin) ")	-	1000	-
9 Table- 12 (iii)(Resistance to combined temperature cycling and external loading)	-	4500	-
7.1(Appearance)	-	1000	-
7.1.1(Color of Finished Pipes)	-	1000	-
7.2 Table-6 (i)(Resistance to Heating oven test at (110±2ºC for 30 minute))	-	4500	-
8.1.1 Table-10 (i)(Ring Stiffness)	-	0	-
Table -1 Cl. No. 5.1, i)(Base Density)	-	0	-
Table -1 Cl. No. 5.1, ii)(Melt Flow Rate (MFR) at (190ºC, 5kg load))	-	0	-
8.1.1 Table-10 (ii)(Impact Strength at (0±1 ºC))	-	0	-
" 5.1 Table-2 ", i)(Resistance to Internal Pressure 165hrs)	-	0	-
" 5.1 Table-2 ", ii)(Resistance to Internal Pressure 1000hrs)	-	0	-
8.1.1, 8.1.2 Table-10 (iii)(Ring flexibility 30% of dem)	-	0	-
6.3.1 & Table-5(Dim (min.) E4 (min) E5 (min.) Socket Length)	-	0	-
6.3.2(Length of Pipe)	-	0	-
8.1.1 Table-10 (iv)(Creep ratio)	-	0	-
6.3.3(Out Side Diameter)	-	0	-
6.3.5.1.1(Ring Stiffness of Spigot + socket)	-	0	-
"6.3.5.1.5 Table-5 "(Socket thickness Avg. (min.) Avg.)	-	0	-
9 Table-12 (i)(Tightness of elastomeric ring seal Joint)	-	0	-
6.3.5.2(Wall Thickness(e4 min))	-	0	-
9 Table 12 (ii)(Water tightness)	-	0	-
6.3.5.2("Construction Height of body wall(ec) Wall Thickness (emin) ")	-	0	-
9 Table- 12 (iii)(Resistance to combined temperature cycling and external loading)	-	0	-
7.1(Appearance)	-	0	-
7.1.1(Color of Finished Pipes)	-	0	-
7.2 Table-6 (i)(Resistance to Heating oven test at (110±2ºC for 30 minute))	-	0	-
8.1.1 Table-10 (i)(Ring Stiffness)	-	0	-
Table -1 Cl. No. 5.1, i)(Base Density)	-	0	-
Table -1 Cl. No. 5.1, ii)(Melt Flow Rate (MFR) at (190ºC, 5kg load))	-	0	-
8.1.1 Table-10 (ii)(Impact Strength at (0±1 ºC))	-	0	-
" 5.1 Table-2 ", i)(Resistance to Internal Pressure 165hrs)	-	0	-
" 5.1 Table-2 ", ii)(Resistance to Internal Pressure 1000hrs)	-	0	-
8.1.1, 8.1.2 Table-10 (iii)(Ring flexibility 30% of dem)	-	0	-
6.3.1 & Table-5(Dim (min.) E4 (min) E5 (min.) Socket Length)	-	0	-
6.3.2(Length of Pipe)	-	0	-
8.1.1 Table-10 (iv)(Creep ratio)	-	0	-
6.3.3(Out Side Diameter)	-	0	-
6.3.5.1.1(Ring Stiffness of Spigot + socket)	-	0	-
"6.3.5.1.5 Table-5 "(Socket thickness Avg. (min.) Avg.)	-	0	-
9 Table-12 (i)(Tightness of elastomeric ring seal Joint)	-	0	-
6.3.5.2(Wall Thickness(e4 min))	-	0	-
9 Table 12 (ii)(Water tightness)	-	0	-
6.3.5.2("Construction Height of body wall(ec) Wall Thickness (emin) ")	-	0	-
9 Table- 12 (iii)(Resistance to combined temperature cycling and external loading)	-	0	-
7.1(Appearance)	-	0	-
7.1.1(Color of Finished Pipes)	-	0	-
7.2 Table-6 (i)(Resistance to Heating oven test at (110±2ºC for 30 minute))	-	0	-
Table -1 Cl. No. 5.1, iii)(Thermal Stability (Oxidation Induction Test, OIT) at 200ºC)	-	0	-
8.1.1 Table-10 (i)(Ring Stiffness)	-	0	-
Table -1 Cl. No. 5.1, i)(Base Density)	-	0	-
Table -1 Cl. No. 5.1, ii)(Melt Flow Rate (MFR) at (190ºC, 5kg load))	-	0	-
8.1.1 Table-10 (ii)(Impact Strength at (0±1 ºC))	-	0	-
" 5.1 Table-2 ", i)(Resistance to Internal Pressure 165hrs)	-	0	-
" 5.1 Table-2 ", ii)(Resistance to Internal Pressure 1000hrs)	-	0	-
8.1.1, 8.1.2 Table-10 (iii)(Ring flexibility 30% of dem)	-	0	-
6.3.1 & Table-5(Dim (min.) E4 (min) E5 (min.) Socket Length)	-	0	-
6.3.2(Length of Pipe)	-	0	-
8.1.1 Table-10 (iv)(Creep ratio)	-	0	-
6.3.3(Out Side Diameter)	-	0	-
6.3.5.1.1(Ring Stiffness of Spigot + socket)	-	0	-
"6.3.5.1.5 Table-5 "(Socket thickness Avg. (min.) Avg.)	-	0	-
9 Table-12 (i)(Tightness of elastomeric ring seal Joint)	-	0	-
6.3.5.2(Wall Thickness(e4 min))	-	0	-
9 Table 12 (ii)(Water tightness)	-	0	-
6.3.5.2("Construction Height of body wall(ec) Wall Thickness (emin) ")	-	0	-
9 Table- 12 (iii)(Resistance to combined temperature cycling and external loading)	-	0	-
7.1(Appearance)	-	0	-
7.1.1(Color of Finished Pipes)	-	0	-
7.2 Table-6 (i)(Resistance to Heating oven test at (110±2ºC for 30 minute))	-	0	-
Table -1 Cl. No. 5.1, iii)(Thermal Stability (Oxidation Induction Test, OIT) at 200ºC)	-	0	-
8.1.1 Table-10 (i)(Ring Stiffness)	-	0	-
Table -1 Cl. No. 5.1, i)(Base Density)	-	0	-
Table -1 Cl. No. 5.1, ii)(Melt Flow Rate (MFR) at (190ºC, 5kg load))	-	0	-
8.1.1 Table-10 (ii)(Impact Strength at (0±1 ºC))	-	0	-
" 5.1 Table-2 ", i)(Resistance to Internal Pressure 165hrs)	-	0	-
" 5.1 Table-2 ", ii)(Resistance to Internal Pressure 1000hrs)	-	0	-
8.1.1, 8.1.2 Table-10 (iii)(Ring flexibility 30% of dem)	-	0	-
6.3.1 & Table-5(Dim (min.) E4 (min) E5 (min.) Socket Length)	-	0	-
6.3.2(Length of Pipe)	-	0	-
8.1.1 Table-10 (iv)(Creep ratio)	-	0	-
6.3.3(Out Side Diameter)	-	0	-
6.3.5.1.1(Ring Stiffness of Spigot + socket)	-	0	-
"6.3.5.1.5 Table-5 "(Socket thickness Avg. (min.) Avg.)	-	0	-
9 Table-12 (i)(Tightness of elastomeric ring seal Joint)	-	0	-
6.3.5.2(Wall Thickness(e4 min))	-	0	-
9 Table 12 (ii)(Water tightness)	-	0	-
6.3.5.2("Construction Height of body wall(ec) Wall Thickness (emin) ")	-	0	-
9 Table- 12 (iii)(Resistance to combined temperature cycling and external loading)	-	0	-
7.1(Appearance)	-	0	-
7.1.1(Color of Finished Pipes)	-	0	-
7.2 Table-6 (i)(Resistance to Heating oven test at (110±2ºC for 30 minute))	-	0	-
Table -1 Cl. No. 5.1, iii)(Thermal Stability (Oxidation Induction Test, OIT) at 200ºC)	-	0	-

-
Included w.e.f 09.04.2025 Scope restricted for PP Pipes only not intended to be jointed in field by fusing or welding. Exclusion Table -1 Cl. No. 5.1, iii) Thermal Stability (Oxidation Induction Test, OIT)

7534

BIS, Central Laboratory (CL)

None

IS 1258 (2024)

Bayonet lampholders (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (General requirements)	-
6 (Standard ratings)	-
7 (Classification)	-
8 (Marking)	-
9 (Dimensions)	-
10 (Protection against electric shock)	-
11 (Terminals)	-
12 (Provision for earthing)	-
13 (Construction)	-
14 (Switched lampholders)	-
15 (Moisture resistance, insulation resistance and electrical strength)	-
16 (Mechanical strength)	-
17 (Screws, current-carrying parts and connections)	-
18 (Creepage distances and clearances)	-
19 (General resistance to heat)	-
20 (Resistance to heat, fire and tracking)	-
21 (Resistance to excessive residual stresses (season cracking) and to rusting)	-
Annex A (Season cracking/corrosion test)	-

-
-

7535

SIIR, Delhi Shriram Institute For Industrial Research

8102006

IS 15462 (2019)

Polymer modified bitumen (Pmb) ? specification (First Revision)

PMB64-10 , PMB70-10 , PMB76-10 , PMB82-10 , PMB76-22

201000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 6.5 table 1(Loss in mass, all types)	-	4000	30% Discount
Clause 6.5 table 1(Viscosity, PMB 64-10, 70-10, 76-10)	-	5000	30% Discount
Clause 6.5 table 1(Viscosity, PMB 76-22)	-	0	Few parameters repeated several times
Clause 6.5 table 1(Viscosity, PMB 82-10)	-	0	-
Clause 6.5 table 1(Softening point, PMB 64-10)	-	3000	30% Discount
Clause 6.5 table 1(Softening point, PMB 70-10)	-	0	-
Clause 6.5 table 1(Softening point, PMB 76-10)	-	0	-
Clause 6.5 table 1(Softening point, PMB 76-22)	-	0	-
Clause 6.5 table 1(Softening point, PMB 82-10)	-	0	-
Clause 6.5 table 1(Flash point, all types)	-	4000	30% Discount
Clause 6.5 table 1(Viscosity, PMB 64-10, 70-10, 76-10)	-	0	-
Clause 6.5 table 1(Viscosity, PMB 76-22)	-	0	-
Clause 6.5 table 1(Viscosity, PMB 82-10)	-	0	-
Clause 6.5 table 1(Softening point, PMB 64-10)	-	0	-
Clause 6.5 table 1(Softening point, PMB 70-10)	-	0	-
Clause 6.5 table 1(Softening point, PMB 76-10)	-	0	-
Clause 6.5 table 1(Softening point, PMB 76-22)	-	0	-
Clause 6.5 table 1(Softening point, PMB 82-10)	-	0	-
Clause 6.5 table 1(Flash point, all types)	-	0	-
Clause 6.5 table 1(Loss in mass, all types)	-	0	-
Clause 6.5 table 1(Viscosity, PMB 64-10, 70-10, 76-10)	-	0	-
Clause 6.5 table 1(Viscosity, PMB 76-22)	-	0	-
Clause 6.5 table 1(Viscosity, PMB 82-10)	-	0	-
Clause 6.5 table 1(Softening point, PMB 64-10)	-	0	-
Clause 6.5 table 1(Softening point, PMB 70-10)	-	0	-
Clause 6.5 table 1(Softening point, PMB 76-10)	-	0	-
Clause 6.5 table 1(Softening point, PMB 76-22)	-	0	-
Clause 6.5 table 1(Softening point, PMB 82-10)	-	0	-
Clause 6.5 table 1(Flash point, all types)	-	0	-
Clause 6.5 table 1(Loss in mass, all types)	-	0	-
Clause 6.5 table 1(Viscosity, PMB 64-10, 70-10, 76-10)	-	0	-
Clause 6.5 table 1(Viscosity, PMB 76-22)	-	0	-
Clause 6.5 table 1(Viscosity, PMB 82-10)	-	0	-
Clause 6.5 table 1(Softening point, PMB 64-10)	-	0	-
Clause 6.5 table 1(Softening point, PMB 70-10)	-	0	-
Clause 6.5 table 1(Softening point, PMB 76-10)	-	0	-
Clause 6.5 table 1(Softening point, PMB 76-22)	-	0	-
Clause 6.5 table 1(Softening point, PMB 82-10)	-	0	-
Clause 6.5 table 1(Flash point, all types)	-	0	-
Clause 6.5 table 1(Loss in mass, all types)	-	0	-
Clause 6.5 table 1(Loss in mass, all types)	-	0	-
Clause 6.5 table 1(Viscosity, PMB 64-10, 70-10, 76-10)	-	0	-
Clause 6.5 table 1(Viscosity, PMB 76-22)	-	0	-
Clause 6.5 table 1(Viscosity, PMB 82-10)	-	0	-
Clause 6.5 table 1(Softening point, PMB 64-10)	-	0	-
Clause 6.5 table 1(Softening point, PMB 70-10)	-	0	-
Clause 6.5 table 1(Softening point, PMB 76-10)	-	0	-
Clause 6.5 table 1(Softening point, PMB 76-22)	-	0	-
Clause 6.5 table 1(Softening point, PMB 82-10)	-	0	-
Clause 6.5 table 1(Flash point, all types)	-	0	-
Clause 6.5 table 1(Viscosity, PMB 64-10, 70-10, 76-10)	-	0	-
Clause 6.5 table 1(Viscosity, PMB 76-22)	-	0	-
Clause 6.5 table 1(Viscosity, PMB 82-10)	-	0	-
Clause 6.5 table 1(Softening point, PMB 64-10)	-	0	-
Clause 6.5 table 1(Softening point, PMB 70-10)	-	0	-
Clause 6.5 table 1(Softening point, PMB 76-10)	-	0	-
Clause 6.5 table 1(Softening point, PMB 76-22)	-	0	-
Clause 6.5 table 1(Softening point, PMB 82-10)	-	0	-
Clause 6.5 table 1(Flash point, all types)	-	0	-
Clause 6.5 table 1(Loss in mass, all types)	-	0	-
Clause 6.5 table 1(Viscosity, PMB 64-10, 70-10, 76-10)	-	0	-
Clause 6.5 table 1(Viscosity, PMB 76-22)	-	0	-
Clause 6.5 table 1(Viscosity, PMB 82-10)	-	0	-
Clause 6.5 table 1(Softening point, PMB 64-10)	-	0	-
Clause 6.5 table 1(Softening point, PMB 70-10)	-	0	-
Clause 6.5 table 1(Softening point, PMB 76-10)	-	0	-
Clause 6.5 table 1(Softening point, PMB 76-22)	-	0	-
Clause 6.5 table 1(Softening point, PMB 82-10)	-	0	-
Clause 6.5 table 1(Flash point, all types)	-	0	-
Clause 6.5 table 1(Loss in mass, all types)	-	0	-
Clause 6.5 table 1(Viscosity, PMB 64-10, 70-10, 76-10)	-	0	-
Clause 6.5 table 1(Viscosity, PMB 76-22)	-	0	-
Clause 6.5 table 1(Viscosity, PMB 82-10)	-	0	-
Clause 6.5 table 1(Softening point, PMB 64-10)	-	0	-
Clause 6.5 table 1(Softening point, PMB 70-10)	-	0	-
Clause 6.5 table 1(Softening point, PMB 76-10)	-	0	-
Clause 6.5 table 1(Softening point, PMB 76-22)	-	0	-
Clause 6.5 table 1(Softening point, PMB 82-10)	-	0	-
Clause 6.5 table 1(Flash point, all types)	-	0	-
Clause 6.5 table 1(Loss in mass, all types)	-	0	-
Cl-6.5 (A) (i)(Softening point (R and B), °C, Min)	-	0	-
Cl-6.5 (A) (ii)(Elastic recovery of half thread in ductilometer at 15°C, percent, Min)	-	3000	30% Discount
Cl-6.5 (A) (iii)(Flash point, COC, °C, Min)	-	0	-
Cl-6.5 (A) (iv)(Viscosity at 150°C, Pa.s, Max)	-	0	-
Cl-6.5 (A) (v)(Complex modulus (G) divided by Sin delta (G/sin δ) as Min 1.0 kPa, 25 mm Plate, 1 mm Gap, at 10 rad/s, at a temperature, °C)	-	40000	30% Discount
Cl-6.5 (A) (vi)(Phase Angle (δ), degree, Max)	-	10000	30% Discount
Cl-6.5 (A) (vii)(Separation, difference in softening point (R&B), °C, Max)	-	5000	30% Discount
Cl-6.5 (A) (viii)(FRAASS breaking1) point, °C, Max)	-	6000	30% Discount
Cl-6.5 (B) (i)(Loss in mass, percent, Max)	-	0	-
Cl-6.5 (B) (ii)(Complex modulus (G) divided by Sin delta (G/sin δ) as Min 2.2 kPa, 25 mm Plate,1 mm Gap, at 10 rad/s at a temperature, °C)	-	40000	30% Discount
Cl-6.5 (C) (i)(Complex modulus (G) multiplied by Sin delta (Gsin δ) as Max 6 000 kPa, 8 mm Plate, 2 mm Gap, at 10 rad/s at a temperature, °C)	-	40000	30% Discount
Cl-6.5 (B) (iii) (a)(Standard Traffic (S) Jnr3.2, Max 4.5 kPa-1 Jnrdiff, Max 75 percent Test Temperature, °C)	-	40000	30% Discount (MSCR Test)
Cl-6.5 (B) (iii) (b)(Heavy Traffic (H) Jnr3.2, Max 2 kPa-1 Jnrdiff, Max 75 percent Test Temperature, °C)	-	0	(MSCR Test)
Cl-6.5 (B) (iii) (c)(Very Heavy Traffic (V) Jnr3.2, Max 1 kPa-1 Jnrdiff, Max 75 percent Test Temperature, °C)	-	0	(MSCR Test)
Cl-6.5 (B) (iii) (d)(Extremely Heavy Traffic (E) Jnr3.2, Max 0.5 kPa-1 Jnrdiff, Max 75 percent Test Temperature, °C)	-	0	(MSCR Test)

31 Dec, 2026

-
Included w.e.f.20.03.2025 Exclusion Cl,4, Cl 6.1, scope restricted for standard traffic only.

7536

CSIR-Central Building Research Institute, Roorkee

9184204

IS/ISO 834 : Part 1 (1999)

Fire-Resistance Tests Elements of Building Construction Part 1 General Requirements

350000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
10(Integrity, Insulation)	-	350000		Rs 350000 plus GST for one hour Rs 450000 plus GST for two hour Rs 10000 for installation charges

12 Mar, 2028

-
-

7537

CSIR-Central Building Research Institute, Roorkee

9184204

IS 3809 (1979)

Fire resistance test for structures

350000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6(Integrity, Insulation)	-	35000		For One hour 3,50,000 plus GST For two hours 4,50,000 plus GST Rs 10000 for installation charges

12 Mar, 2028

-
-

7538

CSIR-Central Building Research Institute, Roorkee

9184204

IS 3614 (2021)

Specification of Fire Doors and Assembly First Revision of IS 3614 Parts 1 2

450000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Integrity, Insulation)	-	450000	For two hours
Cl 7.2.2(SIZE (width))	-	0	-
Cl 7.2.2(SIZE (Height))	-	0	-
Cl 7.4.2(SIZE (width))	-	0	-
Cl 7.4.2(SIZE (Height))	-	0	-
Cl 7.5.2(SIZE (width))	-	0	-
Cl 7.5.2(SIZE (Height))	-	0	-
7.3.1(MOISTURE CONTENT)	-	0	-
7.2.7(Vision Pane (Uninsulated door) Width)	-	0	-
7.2.7(Vision Pane (Uninsulated door) Height)	-	0	-
7.2.7(Vision Pane (Insulated door) Width)	-	0	-
7.2.7(Vision Pane (Insulated door) Height)	-	0	-
7.3.4(Vision Pane (Width))	-	0	-
7.3.4(Vision Pane (Height))	-	0	-
Cl-7.2.1(Material)	-	0	-
Cl-7.2.4(Fire Door Frames)	-	0	-
Cl-7.2.5(Door Leaf)	-	0	-
Cl-7.2.8(Louvres)	-	0	-
Cl 7.3.2(SIZE (width))	-	0	-
Cl 7.3.2(SIZE (Height))	-	0	-
Cl-7.2.9(Builder’s Hardware)	-	0	-
Cl-11.4.3(Hardware)	-	0	-
Cl-7.4.5(Operator)	-	0	-
Cl-7.5.1(Material)	-	0	-
Cl-7.5.3(Construction of Sliding Door Leaf)	-	0	-
Cl-11.3.1(Walls)	-	0	-
Cl-11.4.1(Closing Devices)	-	0	-
Cl-11.4.2(Releasing Devices)	-	0	-
Cl-6(VISION PANE ON FIRE DOORS)	-	0	-
Cl-7.2.3(Construction)	-	0	-
Cl-7.2.6(Intumescent Seal)	-	0	-
Cl-7.3.6(Builder’s Hardware)	-	0	-
Cl-7.4.4(General Requirement of Fire Rated Rolling Shutter)	-	0	-
Cl-7.5.4(General Requirement of Fire Rated Sliding Door)	-	0	-
Cl-7.6(General Requirement of Fire Doors)	-	0	-
Cl-7.3.3(Construction)	-	0	-
Cl-7.4(Avg closing speed of fire rated rolling shutters)	-	0	-
Cl-7.4.3(Construction)	-	0	-

12 Mar, 2028

-
-

7539

Unique Test House LLP

9134536

IS 17876 (2022)

Stainless steel welded pipes and tubes for general service

ALL SIZES GRADE AND DESIGNATIONS

16000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.0 (Table No.- 1)(Chemical Composition,% - IS 228)	-	700	-
10.1 (Table No.- 4)(Tensile Test,Mpa)	-	1000	-
11(Transverse Tension Test,%)	-	1000	-
12 (Table No.- 5)(Hardness Test,HRC,HRB&BHN- IS 1500 (Part 1) or IS 1586 (Part 1))	-	500	-
13 (Table No.- 7)(Flange Test-IS 2330)	-	500	-
14(Reverse Flattaning Test)	-	500	-
15(Flattaning Test-IS 2328)	-	1000	-
16 (Table No.- 8)(Grain Size,No.-IS 4748)	-	500	-
18(Leak Tighteness Test)	-	2000	-
19("Corrosion Test-IS 10461 (Part 1) or IS 10461 (Part 2)")	-	2000	-
22(Workmanship, Finish and Appearance)	-	200	-
23(Repair by Welding or Grinding)	-	500	-
24 (Table No.- 9,10&11)(Dimensions and Tolerances,mm)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Carbon)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Silicon)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Mangnese)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Nickel)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Chromium)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Molybdenum)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Sulphur)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Phosphorous)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Nitrogen)	-	1000	-
"Clause 8.1 and 8.2 - Table 1"(Copper)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Aluminium)	-	2000	-
"Clause 8.1 and 8.2 - Table 1"(Titanium)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Niobium)	-	500	-
"Clause 19 IS 10461(Part 1)"(Corrosion Test)	-	2000	-
Clause 10.1 - Table 4(Tensile Strength)	-	1000	-
Clause 10.1 - Table 4(Yield Strength)	-	1000	-
Clause 10.1 - Table 4(Percent Elongation)	-	1000	-
Clause 11(Transverse Tension Test)	-	1000	-
Clause 12(Hardness Test)	-	500	-
Clause 13(Flange Test)	-	500	-
Clause 14(Reverse Flattening Test)	-	500	-
Clause 15(Flattening Test)	-	500	-
Clause 16(Grain Size)	-	500	-
Clause 18()	-	500	-
"Clause 19 IS 10461(Part 2)"(Corrosion Test)	-	2000	-
Clause 22(Workmanship, Finish & Appearance)	-	500	-
Clause 24 Annexure A, Table 9 Table 10(Dimensions & Tolerances)	-	500	-
8.1 & 8.2 (Table No.- 1)(Vanadium (V))	-	500	-
8.1 & 8.2 (Table No.- 1)(Tantalum (Ta))	-	500	-
12.2(Hardness test)	-	500	-
17(Sampling)	-	200	-
25(Marking)	-	200	-
6.7, Table 7, ii)(c) Chromium VI)	-	500	-

07 Sep, 2028

-
Included.w.e.f.31.01.2025 Exclusion Cl 8.1 & 8.2 (Table no.-1) (Tungstun (W) Cl 20 (Eddy current test, air under water tests, Rediographic tests)

7540

Atharva Laboratories Pvt. Ltd. (D115A), Noida (8134206)

8134206

IS 15298 : Part 3 (2024)

Personal Protective Equipment Part 3 Protective Footwear (ISO 20346 : 2021, MOD) (Third Revision)

39950 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5.2(Design)	-	150	10 % Discount to BIS
Cl 5.2.2(" Height of upper ")	-	250	10 % Discount to BIS
Cl 5.2.3(Heel area)	-	250	10 % Discount to BIS
Cl 5.3.1.1(Construction of whole footwear)	-	150	10 % Discount to BIS
Cl 5.3.1.2(Upper/outsole bond strength)	-	800	10 % Discount to BIS
Cl 5.3.2.1(Toe protection - general)	-	250	10 % Discount to BIS
Cl 5.3.2.2(Internal length)	-	800	10 % Discount to BIS
Cl 5.3.2.3(Width of toecap flange)	-	250	10 % Discount to BIS
Cl 5.3.2.4.1(Corrosion resistance of Class I footwear and hybrid mounted footwear)	-	1000	10 % Discount to BIS
Cl 5.3.2.4.2(Corrosion resistance of Class II and hybrid moulded footwear)	-	1000	10 % Discount to BIS
Cl 5.3.2.5(Behaviour of toecaps (thermal and chemical) of Corrosion resistance)	-	2500	10 % Discount to BIS
Cl 5.3.2.6(Impact resistance)	-	1200	10 % Discount to BIS
Cl 5.3.2.7(Compression resistance)	-	1200	10 % Discount to BIS
Cl 5.3.3(Leak proofness)	-	1000	10 % Discount to BIS
Cl 5.3.4("Specific ergonomic features ")	-	1000	10 % Discount to BIS
Cl 5.3.5.2(Slip resistance on ceramic tile floor with sodium lauryl sulphate (NaLS) solution)	-	1500	10 % Discount to BIS
Cl 5.3.6, Table no 1 of IS 17011 (i)(Allergenic and carcinogenic disperse dyes)	-	3000	10 % Discount to BIS
Cl 5.3.6, Table no 1 of IS 17011 (ii)(Aromatic amines released from Azo dyes (each individual amine))	-	3000	10 % Discount to BIS
Cl 5.3.6, Table no 1 of IS 17011 (iii)(Aromatic amines released from Azo dyes (each individual amine))	-	3000	10 % Discount to BIS
Cl 5.3.6, Table no 1 of IS 17011 (iv)(Chromium (VI))	-	3000	10 % Discount to BIS
Cl 5.3.6, Table no 1 of IS 17011 (v)(Dimethyl fumarate (DMFU))	-	3000	10 % Discount to BIS
Cl 5.3.6, Table no1 of IS 17011 (vi)(Formaldehyde (free or released by partial hydrolysis))	-	3000	10 % Discount to BIS
Cl 5.3.6, Table no 1 of IS 17011 (vii)(Formaldehyde)	-	3000	10 % Discount to BIS
Cl 5.3.6, Table no 1 of IS 17011 (viii)(Organotin compounds)	-	3000	10 % Discount to BIS
Cl 5.3.6, Table no 1 of IS 17011 (ix)(PCP-TeCP-TriCP polychlorophenols)	-	3000	10 % Discount to BIS
Cl 5.3.6, Table no 1 of IS 17011 (x)(pH)	-	3000	10 % Discount to BIS
Cl 5.3.6, Table no 1 of IS 17011 (xi)(Phthalates (each individual phthalate))	-	3000	10 % Discount to BIS
Cl 5.3.6, Table no 1 of IS 17011 (xii)(Nickel, on skin contact)	-	3000	10 % Discount to BIS
Cl 5.3.7(Seam strength)	-	800	10 % Discount to BIS
Cl 5.3.8(Lead Content ( National Annex A))	-	500	10 % Discount to BIS
Cl 5.4.1.1(Class I footwear, determination of the area where upper requirements apply of Upper)	-	250	10 % Discount to BIS
Cl 5.4.1.2(Hybrid footwear, determination of the area where upper requirements apply of Upper)	-	250	10 % Discount to BIS
Cl 5.4.2(Thickness)	-	250	10 % Discount to BIS
Cl 5.4.3(Tear strength)	-	800	10 % Discount to BIS
Cl 5.4.4, Table 11(Tensile properties- Tensile strength)	-	800	10 % Discount to BIS
Cl 5.4.4, Table 11(Tensile properties- Breaking Force)	-	800	10 % Discount to BIS
Cl 5.4.4, Table 11(Tensile properties-Modulus at 100 % elongation)	-	800	10 % Discount to BIS
Cl 5.4.4, Table 11(Tensile properties- Elongation at break)	-	800	10 % Discount to BIS
Cl 5.4.4, Table 11(Tensile properties- Elongation at break)	-	800	10 % Discount to BIS
Cl 5.4.6(Water vapour permeability and coefficient)	-	1200	10 % Discount to BIS
Cl 5.4.7(Resistance to hydrolysis)	-	2000	10 % Discount to BIS
Cl 5.5.2(Lining- Tear strength)	-	800	10 % Discount to BIS
Cl 5.5.3(Lining- Abrasion resistance)	-	1000	10 % Discount to BIS
Cl 5.5.4(Lining-Water vapour permeability and coefficient)	-	1200	10 % Discount to BIS
Cl 5.6.2(Tear strength of tongue)	-	800	10 % Discount to BIS
Cl 5.7.1(Thickness of Insole, insock and footbed)	-	250	10 % Discount to BIS
Cl 5.7.2(Water permeability of insock)	-	500	10 % Discount to BIS
Cl 5.7.3(Water absorption and desorption of Insole, insock and footbed)	-	850	10 % Discount to BIS
Cl 5.7.4.1(Abrasion resistance of Insoles)	-	750	10 % Discount to BIS
Cl 5.7.4.2(Abrasion resistance of Insocks)	-	1200	10 % Discount to BIS
Cl 5.8.2.1(Thickness of Outsole)	-	250	10 % Discount to BIS
Cl 5.8.2.2(Cleated area)	-	250	10 % Discount to BIS
Cl 5.8.2.3(Cleat height)	-	250	10 % Discount to BIS
Cl 5.8.3(Outsole- Tear strength)	-	800	10 % Discount to BIS
Cl 5.8.4(Outsole- Abrasion resistance)	-	1000	10 % Discount to BIS
Cl 5.8.5(Outsole-Flexing resistance)	-	1000	10 % Discount to BIS
Cl 5.8.6(Outsole-Resistance to hydrolysis)	-	2000	10 % Discount to BIS
Cl 5.8.7(Interlayer bond strength)	-	800	10 % Discount to BIS
Cl 6.2.1.1.2(Metallic perforation-resistant inserts (Type P))	-	1000	10 % Discount to BIS
Cl 6.2.1.1.3(Non-metallic perforation-resistant inserts and insoles (Type PL))	-	1000	10 % Discount to BIS
Cl 6.2.1.1.4(Non-metallic perforation-resistant inserts and insoles (Type PS))	-	500	10 % Discount to BIS
Cl 6.2.1.2(Construction of perforation resistant insert)	-	150	10 % Discount to BIS
Cl 6.2.1.3(Dimensions of perforation resistant insert)	-	250	10 % Discount to BIS
Cl 6.2.1.4.1(Flex resistance of perforation-resistant inserts)	-	2000	10 % Discount to BIS
Cl 6.2.1.4.2.1(Corrosion resistance of perforation resistant metallic insert for Class I footwear and hybrid mounted footwear)	-	1000	10 % Discount to BIS
Cl 6.2.1.4.2.2(Corrosion resistance of perforation resistant metallic insert for Class II footwear and hybrid moulded footwear)	-	1000	10 % Discount to BIS
Cl 6.2.1.4.3(Stability against ageing and environmental influence of non-metallic perforationresistant inserts)	-	1000	10 % Discount to BIS
Cl 6.2.2.1(Electrical properties of Partially conductive footwear)	-	1500	10 % Discount to BIS
Cl 6.2.2.2(Electrical properties of Antistatic footwear)	-	1500	10 % Discount to BIS
Cl 6.2.3.1(Heat insulation of outsole complex)	-	1200	10 % Discount to BIS
Cl 6.2.3.2(Cold insulation of outsole complex)	-	1200	10 % Discount to BIS
Cl 6.2.4(Energy absorption of seat region)	-	1000	10 % Discount to BIS
Cl 6.2.5(Water resistance)	-	1000	10 % Discount to BIS
Cl 6.2.6.1(Metatarsal protection - Construction)	-	150	10 % Discount to BIS
Cl 6.2.6.2("Metatarsal protection-Impact resistance of metatarsal protective device ")	-	1000	10 % Discount to BIS
Cl 6.2.7(Ankle protection)	-	800	10 % Discount to BIS
Cl 6.2.8.2(Cut resistance footwear- design)	-	150	10 % Discount to BIS
Cl 6.2.8.2(Dimensions and construction of protective area of Cut resistance footwear)	-	150	10 % Discount to BIS
Cl 6.2.8.3(Resistance to cutting)	-	1200	10 % Discount to BIS
Cl 6.2.9(Scuff cap)	-	1000	10 % Discount to BIS
Cl 6.2.10("Slip resistance on ceramic tile floor with glycerine ")	-	1500	10 % Discount to BIS
Cl 6.3(Upper — Water penetration and absorption)	-	1000	10 % Discount to BIS
Cl 6.4.1(Resistance to hot contact - Outsole)	-	1000	10 % Discount to BIS
Cl 6.4.2(Resistance to fuel oil - Outsole)	-	1500	10 % Discount to BIS
Cl 6.4.3.1(Mechanical properties of Ladder grip)	-	1200	10 % Discount to BIS
Cl 6.4.3.2(Design of Ladder grip)	-	250	10 % Discount to BIS
Cl 6.4.3.3(Cleat height in the waist area of Ladder grip)	-	250	10 % Discount to BIS
Cl 6.4.3.4(Heel breast of Ladder grip)	-	500	10 % Discount to BIS
Cl 7("Marking ")	-	150	10 % Discount to BIS
Cl 7("Marking ")	-	150	10 % Discount to BIS
Cl 5.2(Design)	-	0	-
Cl 5.2.2(" Height of upper ")	-	0	-
Cl 5.2.3(Heel area)	-	0	-
Cl 5.3.1.1(Construction of whole footwear)	-	0	-
Cl 5.3.1.2(Upper/outsole bond strength)	-	0	-
Cl 5.3.2.1(Toe protection - general)	-	0	-
Cl 5.3.2.2(Internal length)	-	0	-
Cl 5.3.2.3(Width of toecap flange)	-	0	-
Cl 5.3.2.4.1(Corrosion resistance of Class I footwear and hybrid mounted footwear)	-	0	-
Cl 5.3.2.4.2(Corrosion resistance of Class II and hybrid moulded footwear)	-	0	-
Cl 5.3.2.5(Behaviour of toecaps (thermal and chemical) of Corrosion resistance)	-	0	-
Cl 5.3.2.6(Impact resistance)	-	0	-
Cl 5.3.2.7(Compression resistance)	-	0	-
Cl 5.3.3(Leak proofness)	-	0	-
Cl 5.3.4("Specific ergonomic features ")	-	0	-
Cl 5.3.5.2(Slip resistance on ceramic tile floor with sodium lauryl sulphate (NaLS) solution)	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (i)(Allergenic and carcinogenic disperse dyes)	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (ii)(Aromatic amines released from Azo dyes (each individual amine))	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (iii)(Aromatic amines released from Azo dyes (each individual amine))	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (iv)(Chromium (VI))	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (v)(Dimethyl fumarate (DMFU))	-	0	-
Cl 5.3.6, Table no1 of IS 17011 (vi)(Formaldehyde (free or released by partial hydrolysis))	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (vii)(Formaldehyde)	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (viii)(Organotin compounds)	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (ix)(PCP-TeCP-TriCP polychlorophenols)	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (x)(pH)	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (xi)(Phthalates (each individual phthalate))	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (xii)(Nickel, on skin contact)	-	0	-
Cl 5.3.7(Seam strength)	-	0	-
Cl 5.3.8(Lead Content ( National Annex A))	-	0	-
Cl 5.4.1.1(Class I footwear, determination of the area where upper requirements apply of Upper)	-	0	-
Cl 5.4.1.2(Hybrid footwear, determination of the area where upper requirements apply of Upper)	-	0	-
Cl 5.4.2(Thickness)	-	0	-
Cl 5.4.3(Tear strength)	-	0	-
Cl 5.4.4, Table 11(Tensile properties- Tensile strength)	-	0	-
Cl 5.4.4, Table 11(Tensile properties- Breaking Force)	-	0	-
Cl 5.4.4, Table 11(Tensile properties-Modulus at 100 % elongation)	-	0	-
Cl 5.4.4, Table 11(Tensile properties- Elongation at break)	-	0	-
Cl 5.4.4, Table 11(Tensile properties- Elongation at break)	-	0	-
Cl 5.4.6(Water vapour permeability and coefficient)	-	0	-
Cl 5.4.7(Resistance to hydrolysis)	-	0	-
Cl 5.5.2(Lining- Tear strength)	-	0	-
Cl 5.5.3(Lining- Abrasion resistance)	-	0	-
Cl 5.5.4(Lining-Water vapour permeability and coefficient)	-	0	-
Cl 5.6.2(Tear strength of tongue)	-	0	-
Cl 5.7.1(Thickness of Insole, insock and footbed)	-	0	-
Cl 5.7.2(Water permeability of insock)	-	0	-
Cl 5.7.3(Water absorption and desorption of Insole, insock and footbed)	-	0	-
Cl 5.7.4.1(Abrasion resistance of Insoles)	-	0	-
Cl 5.7.4.2(Abrasion resistance of Insocks)	-	0	-
Cl 5.8.2.1(Thickness of Outsole)	-	0	-
Cl 5.8.2.2(Cleated area)	-	0	-
Cl 5.8.2.3(Cleat height)	-	0	-
Cl 5.8.3(Outsole- Tear strength)	-	0	-
Cl 5.8.4(Outsole- Abrasion resistance)	-	0	-
Cl 5.8.5(Outsole-Flexing resistance)	-	0	-
Cl 5.8.6(Outsole-Resistance to hydrolysis)	-	0	-
Cl 5.8.7(Interlayer bond strength)	-	0	-
Cl 6.2.1.1.2(Metallic perforation-resistant inserts (Type P))	-	0	-
Cl 6.2.1.1.3(Non-metallic perforation-resistant inserts and insoles (Type PL))	-	0	-
Cl 6.2.1.1.4(Non-metallic perforation-resistant inserts and insoles (Type PS))	-	0	-
Cl 6.2.1.2(Construction of perforation resistant insert)	-	0	-
Cl 6.2.1.3(Dimensions of perforation resistant insert)	-	0	-
Cl 6.2.1.4.1(Flex resistance of perforation-resistant inserts)	-	0	-
Cl 6.2.1.4.2.1(Corrosion resistance of perforation resistant metallic insert for Class I footwear and hybrid mounted footwear)	-	0	-
Cl 6.2.1.4.2.2(Corrosion resistance of perforation resistant metallic insert for Class II footwear and hybrid moulded footwear)	-	0	-
Cl 6.2.1.4.3(Stability against ageing and environmental influence of non-metallic perforationresistant inserts)	-	0	-
Cl 6.2.2.1(Electrical properties of Partially conductive footwear)	-	0	-
Cl 6.2.2.2(Electrical properties of Antistatic footwear)	-	0	-
Cl 6.2.3.1(Heat insulation of outsole complex)	-	0	-
Cl 6.2.3.2(Cold insulation of outsole complex)	-	0	-
Cl 6.2.4(Energy absorption of seat region)	-	0	-
Cl 6.2.5(Water resistance)	-	0	-
Cl 6.2.6.1(Metatarsal protection - Construction)	-	0	-
Cl 6.2.6.2("Metatarsal protection-Impact resistance of metatarsal protective device ")	-	0	-
Cl 6.2.7(Ankle protection)	-	0	-
Cl 6.2.8.2(Cut resistance footwear- design)	-	0	-
Cl 6.2.8.2(Dimensions and construction of protective area of Cut resistance footwear)	-	0	-
Cl 6.2.8.3(Resistance to cutting)	-	0	-
Cl 6.2.9(Scuff cap)	-	0	-
Cl 6.2.10("Slip resistance on ceramic tile floor with glycerine ")	-	0	-
Cl 6.3(Upper — Water penetration and absorption)	-	0	-
Cl 6.4.1(Resistance to hot contact - Outsole)	-	0	-
Cl 6.4.2(Resistance to fuel oil - Outsole)	-	0	-
Cl 6.4.3.1(Mechanical properties of Ladder grip)	-	0	-
Cl 6.4.3.2(Design of Ladder grip)	-	0	-
Cl 6.4.3.3(Cleat height in the waist area of Ladder grip)	-	0	-
Cl 6.4.3.4(Heel breast of Ladder grip)	-	0	-
Cl 7("Marking ")	-	0	-
Cl 7("Marking ")	-	0	-
Cl 5.2(Design)	-	0	-
Cl 5.2.2(" Height of upper ")	-	0	-
Cl 5.2.3(Heel area)	-	0	-
Cl 5.3.1.1(Construction of whole footwear)	-	0	-
Cl 5.3.1.2(Upper/outsole bond strength)	-	0	-
Cl 5.3.2.1(Toe protection - general)	-	0	-
Cl 5.3.2.2(Internal length)	-	0	-
Cl 5.3.2.3(Width of toecap flange)	-	0	-
Cl 5.3.2.4.1(Corrosion resistance of Class I footwear and hybrid mounted footwear)	-	0	-
Cl 5.3.2.4.2(Corrosion resistance of Class II and hybrid moulded footwear)	-	0	-
Cl 5.3.2.5(Behaviour of toecaps (thermal and chemical) of Corrosion resistance)	-	0	-
Cl 5.3.2.6(Impact resistance)	-	0	-
Cl 5.3.2.7(Compression resistance)	-	0	-
Cl 5.3.3(Leak proofness)	-	0	-
Cl 5.3.4("Specific ergonomic features ")	-	0	-
Cl 5.3.5.2(Slip resistance on ceramic tile floor with sodium lauryl sulphate (NaLS) solution)	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (i)(Allergenic and carcinogenic disperse dyes)	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (ii)(Aromatic amines released from Azo dyes (each individual amine))	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (iii)(Aromatic amines released from Azo dyes (each individual amine))	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (iv)(Chromium (VI))	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (v)(Dimethyl fumarate (DMFU))	-	0	-
Cl 5.3.6, Table no1 of IS 17011 (vi)(Formaldehyde (free or released by partial hydrolysis))	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (vii)(Formaldehyde)	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (viii)(Organotin compounds)	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (ix)(PCP-TeCP-TriCP polychlorophenols)	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (x)(pH)	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (xi)(Phthalates (each individual phthalate))	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (xii)(Nickel, on skin contact)	-	0	-
Cl 5.3.7(Seam strength)	-	0	-
Cl 5.3.8(Lead Content ( National Annex A))	-	0	-
Cl 5.4.1.1(Class I footwear, determination of the area where upper requirements apply of Upper)	-	0	-
Cl 5.4.1.2(Hybrid footwear, determination of the area where upper requirements apply of Upper)	-	0	-
Cl 5.4.2(Thickness)	-	0	-
Cl 5.4.3(Tear strength)	-	0	-
Cl 5.4.4, Table 11(Tensile properties- Tensile strength)	-	0	-
Cl 5.4.4, Table 11(Tensile properties- Breaking Force)	-	0	-
Cl 5.4.4, Table 11(Tensile properties-Modulus at 100 % elongation)	-	0	-
Cl 5.4.4, Table 11(Tensile properties- Elongation at break)	-	0	-
Cl 5.4.4, Table 11(Tensile properties- Elongation at break)	-	0	-
Cl 5.4.6(Water vapour permeability and coefficient)	-	0	-
Cl 5.4.7(Resistance to hydrolysis)	-	0	-
Cl 5.5.2(Lining- Tear strength)	-	0	-
Cl 5.5.3(Lining- Abrasion resistance)	-	0	-
Cl 5.5.4(Lining-Water vapour permeability and coefficient)	-	0	-
Cl 5.6.2(Tear strength of tongue)	-	0	-
Cl 5.7.1(Thickness of Insole, insock and footbed)	-	0	-
Cl 5.7.2(Water permeability of insock)	-	0	-
Cl 5.7.3(Water absorption and desorption of Insole, insock and footbed)	-	0	-
Cl 5.7.4.1(Abrasion resistance of Insoles)	-	0	-
Cl 5.7.4.2(Abrasion resistance of Insocks)	-	0	-
Cl 5.8.2.1(Thickness of Outsole)	-	0	-
Cl 5.8.2.2(Cleated area)	-	0	-
Cl 5.8.2.3(Cleat height)	-	0	-
Cl 5.8.3(Outsole- Tear strength)	-	0	-
Cl 5.8.4(Outsole- Abrasion resistance)	-	0	-
Cl 5.8.5(Outsole-Flexing resistance)	-	0	-
Cl 5.8.6(Outsole-Resistance to hydrolysis)	-	0	-
Cl 5.8.7(Interlayer bond strength)	-	0	-
Cl 6.2.1.1.2(Metallic perforation-resistant inserts (Type P))	-	0	-
Cl 6.2.1.1.3(Non-metallic perforation-resistant inserts and insoles (Type PL))	-	0	-
Cl 6.2.1.1.4(Non-metallic perforation-resistant inserts and insoles (Type PS))	-	0	-
Cl 6.2.1.2(Construction of perforation resistant insert)	-	0	-
Cl 6.2.1.3(Dimensions of perforation resistant insert)	-	0	-
Cl 6.2.1.4.1(Flex resistance of perforation-resistant inserts)	-	0	-
Cl 6.2.1.4.2.1(Corrosion resistance of perforation resistant metallic insert for Class I footwear and hybrid mounted footwear)	-	0	-
Cl 6.2.1.4.2.2(Corrosion resistance of perforation resistant metallic insert for Class II footwear and hybrid moulded footwear)	-	0	-
Cl 6.2.1.4.3(Stability against ageing and environmental influence of non-metallic perforationresistant inserts)	-	0	-
Cl 6.2.2.1(Electrical properties of Partially conductive footwear)	-	0	-
Cl 6.2.2.2(Electrical properties of Antistatic footwear)	-	0	-
Cl 6.2.3.1(Heat insulation of outsole complex)	-	0	-
Cl 6.2.3.2(Cold insulation of outsole complex)	-	0	-
Cl 6.2.4(Energy absorption of seat region)	-	0	-
Cl 6.2.5(Water resistance)	-	0	-
Cl 6.2.6.1(Metatarsal protection - Construction)	-	0	-
Cl 6.2.6.2("Metatarsal protection-Impact resistance of metatarsal protective device ")	-	0	-
Cl 6.2.7(Ankle protection)	-	0	-
Cl 6.2.8.2(Cut resistance footwear- design)	-	0	-
Cl 6.2.8.2(Dimensions and construction of protective area of Cut resistance footwear)	-	0	-
Cl 6.2.8.3(Resistance to cutting)	-	0	-
Cl 6.2.9(Scuff cap)	-	0	-
Cl 6.2.10("Slip resistance on ceramic tile floor with glycerine ")	-	0	-
Cl 6.3(Upper — Water penetration and absorption)	-	0	-
Cl 6.4.1(Resistance to hot contact - Outsole)	-	0	-
Cl 6.4.2(Resistance to fuel oil - Outsole)	-	0	-
Cl 6.4.3.1(Mechanical properties of Ladder grip)	-	0	-
Cl 6.4.3.2(Design of Ladder grip)	-	0	-
Cl 6.4.3.3(Cleat height in the waist area of Ladder grip)	-	0	-
Cl 6.4.3.4(Heel breast of Ladder grip)	-	0	-
Cl 7("Marking ")	-	0	-
Cl 7("Marking ")	-	0	-
Cl 5.4.5(Flexing resistance)	-	0	-

21 Jul, 2028

-
Included w.e.f.07.03.2025 Exclusion Cl 6.2.7(Ankle Protection)

7541

ACCURATE TEST SOLUTIONS LLP (F21), NOIDA

8141226

IS 368 (2014)

Electric immersion water heaters - Specification (Fifth Revision)

14500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.6 of IS 302-‐2-‐201:2008(Classification)	-	1000	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	1000	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	1000	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	1000	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	1000	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	1000	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	1000	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	1000	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	1000	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	1000	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	1000	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	1000	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	1000	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	1000	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	1000	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	1000	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	1000	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	1000	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	1000	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	1000	-
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	1000	-
Cl.8 of IS 302‐2-201: 2008(Protection Against Access to Live Parts)	-	1000	-
Cl.10 of IS 302‐2‐201:2008(Power Input and Current )	-	1000	-
Cl.11 of IS 302-2201: 2008(Heating)	-	1000	-
Cl.11 of IS 302-2201: 2008(Heating)	-	1000	-
Cl.11 of IS 302-2201: 2008(Heating)	-	1000	-
Cl.11 of IS 302-2201: 2008(Heating)	-	1000	-
Cl.11 of IS 302-2201: 2008(Heating)	-	1000	-
Cl.11 of IS 302-2201: 2008(Heating)	-	1000	-
Cl.11 of IS 302-2201: 2008(Heating)	-	1000	-
Cl.11 of IS 302-2201: 2008(Heating)	-	1000	-
Cl.11 of IS 302-2201: 2008(Heating)	-	1000	-
Cl.11 of IS 302-2201: 2008(Heating)	-	1000	-
Cl.11 of IS 302-2201: 2008(Heating)	-	1000	-
Cl. 12 of IS 368:2014(Operation under overload conditions of appliances with heating elements)	-	1000	-
Cl.13 of IS 302-2-201: 2008(Leakage Current & Electric Strength at Operating Temperature)	-	1000	-
Cl.13 of IS 302-2-201: 2009(Leakage Current & Electric Strength at Operating Temperature)	-	1000	-
Cl.14 of IS 302‐2-201:2008(Transient Over Voltages )	-	1000	-
Cl.15 of IS 302-2-201:2008(Moisture Resistance )	-	2500	-
Cl.15 of IS 302-2-201:2008(Moisture Resistance )	-	2500	-
Cl.16 of IS 302-2-201:2008(Leakage Current & Electric Strength)	-	1000	-
Cl.16 of IS 302-2-201:2008(Leakage Current & Electric Strength)	-	1000	-
Cl.17 of IS 302‐2-201: 2008(Overload Protection of Transformers & Associated Circuits)	-	1000	-
Cl.18 of IS 368:2014(Endurance)	-	5000	-
Cl.19 of IS 302‐2-201: 2008(Abnormal Operation )	-	1000	-
Cl.19 of IS 302‐2-201: 2008(Abnormal Operation )	-	1000	-
Cl.19 of IS 302‐2-201: 2008(Abnormal Operation )	-	1000	-
Cl.19 of IS 302‐2-201: 2008(Abnormal Operation )	-	1000	-
Cl.20 of IS 302-2-201: 2008(Stability & Mechanical Hazards)	-	1000	-
Cl.21 of IS 302-2-201: 2008(Mechanical Strength )	-	1000	-
Cl.21 of IS 302-2-201: 2008(Mechanical Strength )	-	1000	-
Cl.21 of IS 302-2-201: 2008(Mechanical Strength )	-	1000	-
Cl.22 of IS 302-2-201: 2008(Construction)	-	1000	-
Cl.22 of IS 302-2-201: 2008(Construction)	-	1000	-
Cl.22 of IS 302-2-201: 2008(Construction)	-	1000	-
Cl.22 of IS 302-2-201: 2008(Construction)	-	1000	-
Cl.23 of 302-2-201:2008(Internal Wiring )	-	1000	-
Cl.23 of 302-2-201:2008(Internal Wiring )	-	1000	-
Cl.23 of 302-2-201:2008(Internal Wiring )	-	1000	-
Cl.23 of 302-2-201:2008(Internal Wiring )	-	1000	-
Cl.23 of 302-2-201:2008(Internal Wiring )	-	1000	-
Cl.23 of 302-2-201:2008(Internal Wiring )	-	1000	-
Cl.23 of 302-2-201:2008(Internal Wiring )	-	1000	-
Cl.23 of 302-2-201:2008(Internal Wiring )	-	1000	-
Cl.23 of 302-2-201:2008(Internal Wiring )	-	1000	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	1000	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	1000	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	1000	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	1000	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	1000	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	1000	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	1000	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	1000	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	1000	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	1000	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	1000	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	1000	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	1000	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	1000	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	1000	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	1000	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	1000	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	1000	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	1000	-
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	1000	-
Cl.26 of IS 302-2-201: 2008(Terminals for External Conductors)	-	1000	-
Cl.27 of IS 302-2-201: 2008(Provision for Earthing )	-	1000	-
Cl.27 of IS 302-2-201: 2008(Provision for Earthing )	-	1000	-
Cl.27 of IS 302-2-201: 2008(Provision for Earthing )	-	1000	-
Cl.27 of IS 302-2-201: 2008(Provision for Earthing )	-	1000	-
Cl.27 of IS 302-2-201: 2008(Provision for Earthing )	-	1000	-
Cl.27 of IS 302-2-201: 2008(Provision for Earthing )	-	1000	-
Cl.28 of IS 302-2-201: 2008(Screws & Connections )	-	1000	-
Cl.29 of IS 302-2‐201:2008(Clearances, Creepage Distances and Solid Insulation )	-	1000	-
Cl.29 of IS 302-2‐201:2008(Clearances, Creepage Distances and Solid Insulation )	-	1000	-
Cl.30 of IS 302-2‐201:2008(Resistance to Heat and Fire )	-	1000	-
Cl.30 of IS 302-2‐201:2008(Resistance to Heat and Fire )	-	1000	-
Cl.31 of IS 302-2-201:2008(Resistance of Rusting )	-	1000	-
Cl.32 of IS 302-2-201:2008(Radiation, Toxicity and Similar Hazards)	-	1000	-
4(GENERAL REQUIREMENT)	-	1000	-
5(GENERAL CONDITIONS FOR THE TESTS)	-	1000	-
Cl.19 of IS 302‐2-201: 2008(Abnormal Operation )	-	1000	-

04 Jul, 2027

-
Included w.e.f 11.02.2025 Exclusion : Cl 19.11.4.1 to Cl 19.11.4.7 (EMI/EMC), Cl 24 Component

7542

Akshat Test Lab & Calibration Services, Ghaziabad

8186526

IS 1258 (2024)

Bayonet lampholders (Fifth Revision)

13800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(General requirements)	-	100	-
6(Standard ratings)	-	0	-
7(Classification)	-	100	-
8(Marking)	-	1000	-
9(Dimensions)	-	500	-
10(Protection against electric shock)	-	500	-
11(Terminals)	-	1000	-
12(Provision for earthing)	-	500	-
13(Construction)	-	1000	-
14(Switched lampholders)	-	500	-
15(Moisture resistance, insulation resistance and electrical strength)	-	1000	-
16(Mechanical strength)	-	500	-
17(Screws, current-carrying parts and connections)	-	500	-
18(Creepage distances and clearances)	-	200	-
20(Resistance to heat, fire and tracking)	-	500	-
19(General resistance to heat)	-	500	-
21(Resistance to excessive residual stresses (season cracking) and to rusting)	-	500	-
Annex A(Season cracking/corrosion test)	-	500	-
12.4(Thermal tests)	-	500	-
9.1(Lampholder dimensions)	-	600	-
11.2(Terminals)	-	0	-
12.3(Provision for earthing)	-	600	-
13.1(Construction)	-	0	-
13.8(Construction)	-	0	-
14.4(Switched lampholders)	-	0	-
15.1(Moisture resistance, insulation resistance and electrical strength)	-	1000	-
16.7(Mechanical strength)	-	600	-
16.8(Mechanical strength)	-	600	-
21.2(Resistance to excessive residual stresses (season cracking) and to rusting)	-	1000	For BIS only = Rs 13800/- Acceptance test = 12000/- For others = Rs 27000/-

-
-

7543

Alpha Test House Private Limited, Delhi

8131026

IS 302 : Part 1 (2024)

Household and Similar Electrical Appliances â Safety Part 1 General Requirements (Seventh Revision)

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
12(Charging of metal-ion batteries)	-	1000	10 % discount to BIS
6(Classification- IS 302-1)	-	500	10 % discount to BIS
5(General conditions for the tests)	-	500	10 % discount to BIS
11.8(Temperature rise)	-	1000	10 % discount to BIS
11.7(Duration corresponding)	-	1000	10 % discount to BIS
11.6(Combined appliances)	-	1000	10 % discount to BIS
11.5(Motor-operated appliances)	-	1200	10 % discount to BIS
11.4(Heating appliances)	-	900	10 % discount to BIS
8.1.5(Live parts of built-in appliances)	-	1000	10 % discount to BIS
18(Endurance)	-	500	10 % discount to BIS
17(Overload protection of transformers and associated circuits)	-	1000	10 % discount to BIS
16(Leakage current and electric strength)	-	1000	10 % discount to BIS
4(General requirement)	-	500	10 % discount to BIS
32.1(Radiation Toxicity and Similar Hazards)	-	1000	10 % discount to BIS
31(Resistance to Rusting)	-	1000	10 % discount to BIS
30.2(Needle Flame Test)	-	3000	10 % discount to BIS
30.2(Glow Wire Test)	-	2000	10 % discount to BIS
30.1(Ball pressure test)	-	1000	10 % discount to BIS
29(clearance, creepage distances and solid insulation)	-	2000	10 % discount to BIS
28(Screw test and connections)	-	2000	10 % discount to BIS
27.1(Provision for Earthing, IS 302-1)	-	1000	10 % discount to BIS
26(Terminals for external conductors)	-	1000	10 % discount to BIS
25.8(Supply Connection and External Flexible Cords, IS 302-1)	-	1000	10 % discount to BIS
24(Components)	-	1000	10 % discount to BIS
23.1(Internal Wiring, IS 302-1)	-	1000	10 % discount to BIS
22.1(Construction, IS 302-1)	-	1000	10 % discount to BIS
21.1(Mechanical Strength, IS 302-1)	-	1000	10 % discount to BIS
20.1(Stability & Mechanical Hazards, IS 302-1)	-	1000	10 % discount to BIS
19(Abnormal Operation)	-	1000	10 % discount to BIS
18(Endurance)	-	500	10 % discount to BIS
17(Over Load Protection of Transformers and associated circuits)	-	1000	10 % discount to BIS
16.3(Electric Strength (after clause 15 and 16.2))	-	1000	10 % discount to BIS
16.2(Leakage Current (after Clause 15))	-	1000	10 % discount to BIS
16.1(General)	-	500	10 % discount to BIS
16.0(General)	-	500	10 % discount to BIS
15.3(Humidity Test)	-	1000	10 % discount to BIS
15.2(Spillage Test)	-	1000	10 % discount to BIS
15.1(Ingress Protection test other than IPX0 (IP test))	-	1000	10 % discount to BIS
15.0(Moisture resistance)	-	1000	10 % discount to BIS
14(Transient Over Voltages)	-	1000	10 % discount to BIS
13.3(Electric Strength at operating temperature)	-	1000	10 % discount to BIS
13.2(Leakage current at operating temperature)	-	1000	10 % discount to BIS
13(Leakage current and electric strength at operating temperature)	-	1000	10 % discount to BIS
11.3(Heating)	-	1000	10 % discount to BIS
11.2(General)	-	500	10 % discount to BIS
11.1(General)	-	500	10 % discount to BIS
10.2(Current input)	-	1000	10 % discount to BIS
10.1(Power input)	-	1000	10 % discount to BIS
9(Starting of motor operation test requirements and tests)	-	1000	10 % discount to BIS
8.1.4(Protection against live parts against protective impedance)	-	1000	10 % discount to BIS
8.1.3(Protection against live parts in visible glowing heating elements)	-	1000	10 % discount to BIS
8.1.2(Protection against live parts in openings)	-	1000	10 % discount to BIS
8.1.1(Protection against live parts in all positions)	-	1000	10 % discount to BIS
7(Marking and instructions)	-	500	10 % discount to BIS
A.2(Earth continuity test)	-	1000	10 % discount to BIS
Annex C(Ageing test on motors)	-	1000	10 % discount to BIS
Annex D(Thermal motor protectors)	-	1000	10 % discount to BIS
15.2(Moisture resistance)	-	1000	10 % discount to BIS
19.17(Abnormal Operation, IS 302-1)	-	1000	10 % discount to BIS
20.2(Stability & Mechanical Hazards, IS 302-1)	-	1000	10 % discount to BIS
21.2(Mechanical Strength, IS 302-1)	-	1000	10 % discount to BIS
21.3(Mechanical Strength, IS 302-1)	-	1000	10 % discount to BIS
22.5(Construction)	-	1000	10 % discount to BIS
22.6(Construction, IS 302-1)	-	1000	10 % discount to BIS
22.11(Construction, IS 302-1)	-	1000	10 % discount to BIS
22.16(Construction)	-	1000	10 % discount to BIS
22.32(Construction, IS 302-1)	-	1000	10 % discount to BIS
22.42(Construction)	-	1000	10 % discount to BIS
23.3(Internal Wiring, IS 302-1)	-	1000	10 % discount to BIS
25.6(Supply connection and external flexible cords, IS 302-1)	-	1000	10 % discount to BIS
25.7(Supply Connection and External Flexible Cords, IS 302-1)	-	1000	10 % discount to BIS
25.14(Supply Connection and External Flexible Cords, IS 302-1)	-	1000	10 % discount to BIS
25.15(Supply Connection and External Flexible Cords, IS 302-1)	-	1000	10 % discount to BIS
26.5(Terminals for external conductors)	-	1000	10 % discount to BIS
27.5(Provision for Earthing, IS 302-1)	-	1000	10 % discount to BIS
28.1(Screws and connections)	-	1000	10 % discount to BIS
22.2(Construction, IS 302-1)	-	1000	10 % discount to BIS
22.3(Construction, IS 302-1)	-	1000	10 % discount to BIS
B.22.4(Construction, IS 302-1)	-	1000	10 % discount to BIS
B.22.5(Construction, IS 302-1)	-	1000	10 % discount to BIS

-
Included .w.e.f.11.02.2025 Exclusion 19.11.4.1 to 19.11.4.7 (EMI/EMC) "Domestic Electric Clothes Washing Machines (For testing charges please refer part 2 standard in LIMS)"

7544

BIS, Central Laboratory (CL)

None

IS 13428 (2024)

PACKAGED NATURAL MINERAL WATER - SPECIFICATION Third Revision

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.2/Table 1/i (Colour)	-
6.2/Table 1/ii (Odour)	-
6.2/Table 1/iii (Taste)	-
6.2/Table 1/iv (Turbidity)	-
6.2/Table 1/v (Total Dissoved)	-
6.2/Table 1/vi (pH Value)	-
6.2/Table 2/ii (Nitrite)	-
6.2/Table 2/iv (Manganese)	-
6.2/Table 2/v (Copper)	-
6.2/Table 2/vi (Fluoride)	-
6.2/Table 2/vii (Barium)	-
6.2/Table 2/viii (Antimony)	-
6.2/Table 2/ix (Borate)	-
6.2/Table 2/x (Silver)	-
6.2/Table 2/xi (Chloride)	-
6.2/Table 2/xii (Sulphate)	-
6.2/Table 2/xiii (Magnesium)	-
6.2/Table 2/xiv (Calcium)	-
6.2/Table 2/xv (Sodium)	-
6.2/Table 2/xvi (Alkalinity)	-
6.2/Table 2/xvii (Selenium)	-
6.2/Table 3/i (Arsenic)	-
6.2/Table 3/ii (Cadmium)	-
6.2/Table 3/iv (Chromium)	-
6.2/Table 3/v (Mercury)	-
6.2/Table 3/vi (Lead)	-
6.2/Table 3/vii (Nickel)	-
6.2/Table 3/viii (Polychlorinated biphenyle (PCB))	-
6.2/Table 3/ix (Polynuclear aromatic hydrocarbons)	-
6.1.1 (Escherichia coli)	-
6.1.2 (Coliform)	-
6.1.3 (Faecal Streptococci)	-
Cl-6.1.3 (Staphylococcus aureus)	-
6.1.4 (Sulphite Reducing Anaerobe)	-
6.1.5 (Pseudomonas aeruginosa)	-
6.1.6 (Yeast and moould)	-
6.1.7 (Salmonella)	-
Cl-6.1.7 (Shigella)	-
6.1.8 (Vibrio Cholera)	-
Cl-6.1.8 (V. parahaemolyticus)	-
6.2/Table 3/x (Uranium)	-

-
13 Litre for chemical and 12 lt for microbiology

7545

Intertek India Private Limited (Gujarat)

7166626

IS 14286 : Part 1 : Sec 1 (2023)

Terrestrial photovoltaic PV modules Design qualification and type approval Part 1-1: Special requirements for testing of crystalline silicon photovoltaic PV modules Third Revision

1814240 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-8(Major visual defects)	-	0	-
Cl-11.1(Visual inspection)	-	17200	-
Cl-11.2(Maximum power determination)	-	55200	-
Cl-11.3(Insulation test)	-	12650	-
Cl-11.4(Measurement of temperature coefficients)	-	27600	-
Cl-11.5(Measurement of nominal module operating temperature)	-	0	-
Cl-11.6(Performance at STC)	-	294000	-
Cl-11.7(Performance at low irradiance)	-	4600	-
Cl-11.8(Outdoor exposure test)	-	23040	-
Cl-11.9(Hot-spot endurance test)	-	67200	-
Cl-11.10(UV preconditioning test)	-	53520	-
Cl-11.11(Thermal cycling test)	-	94080	-
Cl-11.12(Humidity-freeze test)	-	35376	-
Cl-11.13(Damp heat test)	-	122535	-
Cl-11.14(Robustness of terminations test)	-	1272	-
Cl-11.15(Wet leakage current tes)	-	33800	-
Cl-11.16(Static mechanical load test)	-	13680	-
Cl-11.17(Hail test)	-	15120	-
Cl-11.18(Bypass diode thermal test)	-	12560	-
Cl-11.19(Stabilization)	-	2100	-
5(Marking and documentation)	-	0	-
11.20(Cyclic (dynamic) mechanical load test (MQT 20))	-	11400	-
11.21(Potential induced degradation test (MQT 21))	-	26000	-
11.22(Bending test (MQT 22))	-	4000	-
Cl-8(Major visual defects)	-	0	-
Cl-11.1(Visual inspection)	-	0	-
Cl-11.2(Maximum power determination)	-	0	-
Cl-11.3(Insulation test)	-	0	-
Cl-11.4(Measurement of temperature coefficients)	-	0	-
Cl-11.5(Measurement of nominal module operating temperature)	-	0	-
Cl-11.6(Performance at STC)	-	0	-
Cl-11.7(Performance at low irradiance)	-	0	-
Cl-11.8(Outdoor exposure test)	-	0	-
Cl-11.9(Hot-spot endurance test)	-	0	-
Cl-11.10(UV preconditioning test)	-	0	-
Cl-11.11(Thermal cycling test)	-	0	-
Cl-11.12(Humidity-freeze test)	-	0	-
Cl-11.13(Damp heat test)	-	0	-
Cl-11.14(Robustness of terminations test)	-	0	-
Cl-11.15(Wet leakage current tes)	-	0	-
Cl-11.16(Static mechanical load test)	-	0	-
Cl-11.17(Hail test)	-	0	-
Cl-11.18(Bypass diode thermal test)	-	0	-
Cl-11.19(Stabilization)	-	0	-
5(Marking and documentation)	-	0	-
11.20(Cyclic (dynamic) mechanical load test (MQT 20))	-	0	-
11.21(Potential induced degradation test (MQT 21))	-	0	-
11.22(Bending test (MQT 22))	-	0	-
Cl-8(Major visual defects)	-	0	-
Cl-11.1(Visual inspection)	-	0	-
Cl-11.2(Maximum power determination)	-	0	-
Cl-11.3(Insulation test)	-	0	-
Cl-11.4(Measurement of temperature coefficients)	-	0	-
Cl-11.5(Measurement of nominal module operating temperature)	-	0	-
Cl-11.6(Performance at STC)	-	0	-
Cl-11.7(Performance at low irradiance)	-	0	-
Cl-11.8(Outdoor exposure test)	-	0	-
Cl-11.9(Hot-spot endurance test)	-	0	-
Cl-11.10(UV preconditioning test)	-	0	-
Cl-11.11(Thermal cycling test)	-	0	-
Cl-11.12(Humidity-freeze test)	-	0	-
Cl-11.13(Damp heat test)	-	0	-
Cl-11.14(Robustness of terminations test)	-	0	-
Cl-11.15(Wet leakage current tes)	-	0	-
Cl-11.16(Static mechanical load test)	-	0	-
Cl-11.17(Hail test)	-	0	-
Cl-11.18(Bypass diode thermal test)	-	0	-
Cl-11.19(Stabilization)	-	0	-
5(Marking and documentation)	-	0	-
11.20(Cyclic (dynamic) mechanical load test (MQT 20))	-	0	-
11.21(Potential induced degradation test (MQT 21))	-	0	-
11.22(Bending test (MQT 22))	-	0	-

02 Dec, 2029

-
Included w.e.f. 04.04.2025

7546

Cotecna Inspection India Private Limited, Gurugram

8166106

IS 3976 (2018)

Safety Rubber Canvas Boots for Miners Ã¢â‚¬ Specification ( Sixth Revision )

24525 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.5.2.5 Compact Sole Heel Cl.5.2.5.1 IS 3400 (Part 2)(requirements prescribed in col 3 of Table 2 when tested as per corresponding test methods prescribed in col 4 of Table 2. i)i) Hardness (IRHD)	-	500	As per applicable clauses
Cl.6.3 Tear Strength of Compact Outsole( When outsoles are tested in accordance to 8.2 of IS 15298 (Part 1), the tear strength shall be not less than 8 kN/m for material having density higher than 0.9/cm³ and when density of material is less than or equal to 0.9 g/cm³, tear strength shall not be less than 5 kN/m.)	-	500	As per applicable clauses
Cl.5.2.3 Coated Binding Material IS 1954( Coated binding materials shall conform to the requirements given in col 3 of Table 1 when tested according to the methods prescribed in col 4 of Table 1. i)Width in mm, )	-	500	As per applicable clauses
Cl.5.2.1.4 ( Type 2 footwear, the composite upper material shall comply with requirements of water coefficient as prescribed in 5.4.6 of IS 15298 (Part 2).)	-	500	As per applicable clauses
Cl.5.13 Energy Absorption Test(When footwear is tested in accordance with the method prescribed in 5.14 of IS 15298 (Part 1), the energy absorption of the seat region shall not be less than 20 J.)	-	500	As per applicable clauses
Cl.5.2.3 Coated Binding Material Annex C(ii) Breaking load in N, Min (50 cm grip length test specimen) )	-	500	As per applicable clauses
Cl.5.2.1.4 ( Type 2 footwear, the composite upper material shall comply with requirements of water vapour permeability as prescribed in 5.4.6 of IS 15298 (Part 2).)	-	500	As per applicable clauses
CL.5.2.10 Counter Stiffener( A counter stiffener, made out of textile reinforced withpolymer/rubber including (thermoplastic) having thickness not less than 1.5 mm is to be stitched at inside of upper so as to fortify the back of the footwear at joints of quarter.)	-	500	As per applicable clauses
Cl.5.1.1 Fittings(Fittings of the footwear shall be in conformity to Table 9 of IS 1638 (measurement of men’s lasts) and Table 8 of IS 1638 (measurement of women’s lasts).)	-	500	As per applicable clauses
Cl.5.2.1 Upper Cl.5.2.1.1 IS 3400(Part 5)( Composite upper material shall comply with consolidation test as per 5.10.(IS 3400 (Part 5). There shall be no separation at a load of 1.5 kg.))	-	500	As per applicable clauses
Cl.5.2.1.2( Composite upper material shall comply with tear strength as per 5.4.3 of IS 15298 (Part 2).)	-	500	As per applicable clauses
Cl.5.2.1.3 , Cl.6.5 of IS 15298 (Part 1).( Composite upper material shall develop no cracks before 150 000 cycles when tested in accordance with 6.5 of IS 15298 (Part 1).)	-	500	As per applicable clauses
Cl.5.2.1.5( Inner layer of upper shall meet requirement of abrasion resistance as prescribed in 5.5.2 of IS 15298 (Part 2).)	-	500	As per applicable clauses
Cl.5.2.2 Compact Insole/Compact Insocks/Counter Stiffener Lining(Textile material shall be used as lining material for compact insole/compact insocks / counter stiffener. It shall meet the requirement of tear strength as prescribed in 5.6.1 of IS 15298 (Part 2).)	-	500	As per applicable clauses
Cl.5.2.2.1 Abrasion resistance of compact insole/insocks/ counter stiffener( When textiles used as lining for all the above are tested in accordance with 6.12 of IS 15298 (Part 1), the lining shall not develop any holes before the following number of cycles has been performed:)	-	500	As per applicable clauses
Cl.5.2.3.1 In case of cotton black binding materia( the same shall be free from sulphur dyes when tested in accordance with Annex B.)	-	500	As per applicable clauses
Cl.5.2.5 Compact Sole Heel Cl. 5.2.5.1 (The compact sole heel shall be made out of polymeric/rubber components and the typical design recommendation (not mandatory) of compact sole heel is as shown in Fig. 3. Sectional view of Type 1/Type 2 ) toe position is given in Fig. 4.)	-	500	As per applicable clauses
Cl.5.2.5 Compact Sole Heel 5.2.5.1 IS 3400 (Part 4)(ii)*Change in hardness after accelerated ageing at 100 ± 2 °C for 24 h )	-	500	As per applicable clauses
Cl.5.2.5.3 Ageing for whole footwear(When rubber is used for manufacturing boots or when the outer sole heel is made of bi-polymer, the finished boots shall be aged at 100 ± 2°C for 24 h. On completion of test, all rubber components shall not develop any sign of tackiness or brittleness.)	-	500	As per applicable clauses
Cl.5.2.5.4 Thickness of compact sole hee(Thickness of compact sole heel of the boots shall comply with the thickness and material requirements prescribed in Table 3.)	-	500	As per applicable clauses
Cl.5.2.5.4 Thickness of compact sole hee(of black cotton thread, the same shall be free from sulphur dyes when tested in accordance with Annex B.)	-	500	As per applicable clauses
Cl.5.2.6 Thread for Upper Closing( The length (m/kg) and construction of sewing thread shall conform to requirements as prescribed in Table 4.)	-	500	As per applicable clauses
Cl.5.2.7 Safety Toe Cap(Safety toe cap as per 3.6 shall be fitted into the footwear and must not come out while in use.)	-	500	As per applicable clauses
Cl.5.2.8.1( The boots shall be provided with laces having minimum length of 115 cm for Type 1 and minimum 100 cm for Type 2.)	-	500	As per applicable clauses
Cl.5.2.8.2 (Minimum breaking load of 60 kg is to be achieved when tested between 18 cm grip length in accordance with Annex C.)	-	500	As per applicable clauses
Cl.5.2.8.3( In case of cotton lace of black colour, the same shall be free from sulphur dyes when tested in accordance with Annex B. Two ends of the laces shall be provided with plastic tips.)	-	500	As per applicable clauses
Cl.5.2.9 Eyelets( Aluminum eyelets of external collar diameter not less than 10 mm and wall thickness of 0.30 to 0.35 mm shall be used.)	-	500	As per applicable clauses
Cl.5.3.2 (The tongue shall be made out of composite upper material and shall be half bellow type for Type 2 and full bellow type for Type 1.)	-	500	As per applicable clauses
Cl.5.3.5 Outer toe cap( shall be provided which is made of polymer/rubber and it shall be strongly adhered such that it shall not open up or come out while in use. Toe of the boot shall be reinforced with safety toe cap)	-	500	As per applicable clauses
Cl.5.3.6( A designed foxing of width of minimum 25 mm and of thickness of minimum 2 mm is to be provided. The foxing shall not extend the edges of the outer sole.)	-	500	As per applicable clauses
Cl.5.3.7( Two pairs of detachable insocks are to be provided. The insocks shall be compact in nature having thickness not less than 2 mm.)	-	500	As per applicable clauses
Cl.5.4 Finish( In appearance, general workmanship and in all other respects with regard to finish and get up of the footwear, the footwear shall be matching to the approved sample of the purchaser.)	-	500	As per applicable clauses
Cl.5.5 Mass(The mass of one pair of finished footwear of size 8 shall not exceed 1 500 g for Type 1 and 1 400 g for Type 2 with an increase or decrease of 100 g for each bigger or smaller size, respectively.)	-	500	As per applicable clauses
Cl.5.6( Height of Upper Height of upper of the boots shall conform to column 5 (Design C) and column 4 (Design B) of 5.2.2, Table 4 of IS 15298 (Part 2) for Type 1 and Type 2, respectively when measured as per 6.2 of IS 15298 (Part 1) on the inside of the back of the footwear and from seat of the insole to top edge of the upper.)	-	500	As per applicable clauses
Cl.5.7 Performance Test(When safety footwear is tested in accordance with the method described in 5.4 of IS 15298 (Part 1), at an impact energy of (200 ± 4) J, the clearance under the toecap at the moment of impact shall be in accordance with Table 5. In addition, the toecap shall not develop any cracks which go through the material, that is, through which light can be seen.)	-	500	As per applicable clauses
Cl.5.8 Upper/Outsole Bond Strength(When the footwear is tested in accordance with the method prescribed in 5.2 of IS 15298 (Part 1), the bond strength shall not be less than 4.0 N/mm, unless there is tearing of the sole in which case the bond strength shall not be less than 3.0 N/mm.)	-	500	As per applicable clauses
Cl.5.9 Sole Interlayer Bond Strength for Bi-polymer( and Bi-density Sole When tested in accordance with 5.2 of IS 15298 (Part 1), the bond strength between the outer or cleated layer and the adjacent layer shall not be less than 4.0 N/mm unless there is tearing of any part of the sole, in which case the bond strength shall not be less than 3.0 N/mm.)	-	500	As per applicable clauses
Cl.5.10 Consolidation Test( Representative sample of width 25 ± 0.5 mm are cut out from the quarter of the upper along the length of boot. The plies are separated by breaking the bond. Carry out the test on two specimens in accordance with IS 3400 (Part 5). Th)	-	500	As per applicable clauses
Cl.5.11 Compression Resistance( 5.11.1 When safety boots are tested in accordance with 5.5 of IS 15298 (Part 1), the clearance under the toe cap at a compression load of 15 kN ± 0.1 kN shall be in accordance with Table 5.)	-	500	As per applicable clauses
Cl.5.12 Internal Length of Toe Cap( For safety boots, internal length of the toe cap shall meet the specification given in Table 5 of IS 15298 (Part 2) when tested as per 5.3 of IS 15298 (Part 1).)	-	500	As per applicable clauses
Cl.6.1 Abrasion Resistance of Compact Outsole( When outsole is tested in accordance with 8.3 of IS 15298 (Part 1), the relative volume loss shall not be greater than 250 mm³ for materials having density 0.9 g/cm³ or less, and not greater than 150 mm³ for materials with density greater than 0.9 g/cm³.)	-	500	As per applicable clauses
Cl.6.2 Flexing Resistance of Compact Outsole( When outsole is tested in accordance with 8.4 of IS 15298 (Part 1), the cut growth shall not be greater than 4 mm before 30 000 cycles.)	-	500	As per applicable clauses
Cl.6.4 Resistance to Hot Contact( — Sole Heel When sole heel is tested in accordance with 8.7 of IS 15298 (Part 1), the material shall not melt/deform and shall not develop any cracks when bent around the mandrel.)	-	500	As per applicable clauses
Cl.6.5 Hydrolysis( When bottom sole or other components are made out of polyurethane, the same shall be tested in accordance with 8.5 of IS 15298 (Part 1) and the same shall comply with 5.8.5 of IS 15298 (Part 2).)	-	500	As per applicable clauses
Cl.5.2.5 Compact Sole Heel Cl.5.2.5.1 IS 3400 (Part 2)(requirements prescribed in col 3 of Table 2 when tested as per corresponding test methods prescribed in col 4 of Table 2. i)i) Hardness (IRHD)	-	500	As per applicable clauses
Cl.6.3 Tear Strength of Compact Outsole( When outsoles are tested in accordance to 8.2 of IS 15298 (Part 1), the tear strength shall be not less than 8 kN/m for material having density higher than 0.9/cm³ and when density of material is less than or equal to 0.9 g/cm³, tear strength shall not be less than 5 kN/m.)	-	500	As per applicable clauses
Cl.5.2.3 Coated Binding Material IS 1954( Coated binding materials shall conform to the requirements given in col 3 of Table 1 when tested according to the methods prescribed in col 4 of Table 1. i)Width in mm, )	-	500	As per applicable clauses
Cl.5.2.1.4 ( Type 2 footwear, the composite upper material shall comply with requirements of water coefficient as prescribed in 5.4.6 of IS 15298 (Part 2).)	-	500	As per applicable clauses
Cl.5.1.1 Fittings(Fittings of the footwear shall be in conformity to Table 9 of IS 1638 (measurement of men’s lasts) and Table 8 of IS 1638 (measurement of women’s lasts).)	-	500	As per applicable clauses
Cl.5.2.1 Upper Cl.5.2.1.1 IS 3400(Part 5)( Composite upper material shall comply with consolidation test as per 5.10.(IS 3400 (Part 5). There shall be no separation at a load of 1.5 kg.))	-	500	As per applicable clauses
Cl.5.2.1.2( Composite upper material shall comply with tear strength as per 5.4.3 of IS 15298 (Part 2).)	-	500	As per applicable clauses
Cl.5.2.1.3 , Cl.6.5 of IS 15298 (Part 1).( Composite upper material shall develop no cracks before 150 000 cycles when tested in accordance with 6.5 of IS 15298 (Part 1).)	-	500	As per applicable clauses
Cl.5.2.1.5( Inner layer of upper shall meet requirement of abrasion resistance as prescribed in 5.5.2 of IS 15298 (Part 2).)	-	500	As per applicable clauses
Cl.5.2.2 Compact Insole/Compact Insocks/Counter Stiffener Lining(Textile material shall be used as lining material for compact insole/compact insocks / counter stiffener. It shall meet the requirement of tear strength as prescribed in 5.6.1 of IS 15298 (Part 2).)	-	500	As per applicable clauses
Cl.5.2.2.1 Abrasion resistance of compact insole/insocks/ counter stiffener( When textiles used as lining for all the above are tested in accordance with 6.12 of IS 15298 (Part 1), the lining shall not develop any holes before the following number of cycles has been performed:)	-	500	As per applicable clauses
Cl.5.2.3.1 In case of cotton black binding materia( the same shall be free from sulphur dyes when tested in accordance with Annex B.)	-	500	As per applicable clauses
Cl.5.2.5 Compact Sole Heel Cl. 5.2.5.1 (The compact sole heel shall be made out of polymeric/rubber components and the typical design recommendation (not mandatory) of compact sole heel is as shown in Fig. 3. Sectional view of Type 1/Type 2 ) toe position is given in Fig. 4.)	-	500	As per applicable clauses
Cl.5.2.5 Compact Sole Heel 5.2.5.1 IS 3400 (Part 4)(ii)*Change in hardness after accelerated ageing at 100 ± 2 °C for 24 h )	-	500	As per applicable clauses
Cl.5.2.5.3 Ageing for whole footwear(When rubber is used for manufacturing boots or when the outer sole heel is made of bi-polymer, the finished boots shall be aged at 100 ± 2°C for 24 h. On completion of test, all rubber components shall not develop any sign of tackiness or brittleness.)	-	500	As per applicable clauses
Cl.5.2.5.4 Thickness of compact sole hee(Thickness of compact sole heel of the boots shall comply with the thickness and material requirements prescribed in Table 3.)	-	500	As per applicable clauses
Cl.5.2.5.4 Thickness of compact sole hee(of black cotton thread, the same shall be free from sulphur dyes when tested in accordance with Annex B.)	-	500	As per applicable clauses
Cl.5.2.6 Thread for Upper Closing( The length (m/kg) and construction of sewing thread shall conform to requirements as prescribed in Table 4.)	-	500	As per applicable clauses
Cl.5.2.7 Safety Toe Cap(Safety toe cap as per 3.6 shall be fitted into the footwear and must not come out while in use.)	-	500	As per applicable clauses
Cl.5.2.8.1( The boots shall be provided with laces having minimum length of 115 cm for Type 1 and minimum 100 cm for Type 2.)	-	500	As per applicable clauses
Cl.5.2.8.2 (Minimum breaking load of 60 kg is to be achieved when tested between 18 cm grip length in accordance with Annex C.)	-	500	As per applicable clauses
Cl.5.2.8.3( In case of cotton lace of black colour, the same shall be free from sulphur dyes when tested in accordance with Annex B. Two ends of the laces shall be provided with plastic tips.)	-	500	As per applicable clauses
Cl.5.2.9 Eyelets( Aluminum eyelets of external collar diameter not less than 10 mm and wall thickness of 0.30 to 0.35 mm shall be used.)	-	500	As per applicable clauses
Cl.5.3.2 (The tongue shall be made out of composite upper material and shall be half bellow type for Type 2 and full bellow type for Type 1.)	-	500	As per applicable clauses
Cl.5.3.5 Outer toe cap( shall be provided which is made of polymer/rubber and it shall be strongly adhered such that it shall not open up or come out while in use. Toe of the boot shall be reinforced with safety toe cap)	-	500	As per applicable clauses
Cl.5.3.6( A designed foxing of width of minimum 25 mm and of thickness of minimum 2 mm is to be provided. The foxing shall not extend the edges of the outer sole.)	-	500	As per applicable clauses
Cl.5.3.7( Two pairs of detachable insocks are to be provided. The insocks shall be compact in nature having thickness not less than 2 mm.)	-	500	As per applicable clauses
Cl.5.4 Finish( In appearance, general workmanship and in all other respects with regard to finish and get up of the footwear, the footwear shall be matching to the approved sample of the purchaser.)	-	500	As per applicable clauses
Cl.5.5 Mass(The mass of one pair of finished footwear of size 8 shall not exceed 1 500 g for Type 1 and 1 400 g for Type 2 with an increase or decrease of 100 g for each bigger or smaller size, respectively.)	-	500	As per applicable clauses
Cl.5.6( Height of Upper Height of upper of the boots shall conform to column 5 (Design C) and column 4 (Design B) of 5.2.2, Table 4 of IS 15298 (Part 2) for Type 1 and Type 2, respectively when measured as per 6.2 of IS 15298 (Part 1) on the inside of the back of the footwear and from seat of the insole to top edge of the upper.)	-	500	As per applicable clauses
Cl.5.7 Performance Test(When safety footwear is tested in accordance with the method described in 5.4 of IS 15298 (Part 1), at an impact energy of (200 ± 4) J, the clearance under the toecap at the moment of impact shall be in accordance with Table 5. In addition, the toecap shall not develop any cracks which go through the material, that is, through which light can be seen.)	-	500	As per applicable clauses
Cl.5.8 Upper/Outsole Bond Strength(When the footwear is tested in accordance with the method prescribed in 5.2 of IS 15298 (Part 1), the bond strength shall not be less than 4.0 N/mm, unless there is tearing of the sole in which case the bond strength shall not be less than 3.0 N/mm.)	-	500	As per applicable clauses
Cl.5.9 Sole Interlayer Bond Strength for Bi-polymer( and Bi-density Sole When tested in accordance with 5.2 of IS 15298 (Part 1), the bond strength between the outer or cleated layer and the adjacent layer shall not be less than 4.0 N/mm unless there is tearing of any part of the sole, in which case the bond strength shall not be less than 3.0 N/mm.)	-	500	As per applicable clauses
Cl.5.10 Consolidation Test( Representative sample of width 25 ± 0.5 mm are cut out from the quarter of the upper along the length of boot. The plies are separated by breaking the bond. Carry out the test on two specimens in accordance with IS 3400 (Part 5). Th)	-	500	As per applicable clauses
Cl.5.11 Compression Resistance( 5.11.1 When safety boots are tested in accordance with 5.5 of IS 15298 (Part 1), the clearance under the toe cap at a compression load of 15 kN ± 0.1 kN shall be in accordance with Table 5.)	-	500	As per applicable clauses
Cl.5.12 Internal Length of Toe Cap( For safety boots, internal length of the toe cap shall meet the specification given in Table 5 of IS 15298 (Part 2) when tested as per 5.3 of IS 15298 (Part 1).)	-	500	As per applicable clauses
Cl.6.1 Abrasion Resistance of Compact Outsole( When outsole is tested in accordance with 8.3 of IS 15298 (Part 1), the relative volume loss shall not be greater than 250 mm³ for materials having density 0.9 g/cm³ or less, and not greater than 150 mm³ for materials with density greater than 0.9 g/cm³.)	-	500	As per applicable clauses
Cl.6.2 Flexing Resistance of Compact Outsole( When outsole is tested in accordance with 8.4 of IS 15298 (Part 1), the cut growth shall not be greater than 4 mm before 30 000 cycles.)	-	500	As per applicable clauses
Cl.6.4 Resistance to Hot Contact( — Sole Heel When sole heel is tested in accordance with 8.7 of IS 15298 (Part 1), the material shall not melt/deform and shall not develop any cracks when bent around the mandrel.)	-	500	As per applicable clauses
Cl.6.5 Hydrolysis( When bottom sole or other components are made out of polyurethane, the same shall be tested in accordance with 8.5 of IS 15298 (Part 1) and the same shall comply with 5.8.5 of IS 15298 (Part 2).)	-	500	As per applicable clauses
4(Types)	-	500	As per applicable clauses
5(Requirements)	-	500	As per applicable clauses
5.1(Design)	-	500	As per applicable clauses
5.10(consolidation test IS 3400 (Part 5))	-	500	As per applicable clauses
5.2.4(Reinforcing Material)	-	500	As per applicable clauses
5.2.8.4(Colour of the lace)	-	500	As per applicable clauses
5.3, 5.3.1,5.3.3,5.3.4(Construction)	-	500	As per applicable clauses
5.10(Consolidation Test IS 3400 (Part 5) : 1986)	-	500	As per applicable clauses
8(CHEMICAL REQUIREMENTS)	-	5000	As per applicable clauses
9, 9.1(BIS CERTIFICATION MARKING)	-	500	As per applicable clauses
10(Marking)	-	500	As per applicable clauses
11(Packing)	-	500	As per applicable clauses
Cl. 5.2.4(Reinforcing Material)	-	200	-
Cl. 5.2.8.4(Colour of the lace)	-	200	-
11(PACKING)	-	200	-
Cl. 5.3(Construction 5.3.1,5.3.3,5.3.4)	-	200	-
10(Marking)	-	200	-
7.1(Resistance to fuel)	-	900	-
7.2(Resistance to electricity)	-	3000	-
9, 9.1(BIS CERTIFICATION MARKING)	-	200	-
Cl. 8 (IS 17011, Table-1 (i))(Allergenic and carcinogenic disperse dyes)	-	4980	-
Cl-8 (IS 17011, Table-1 (ii)(Aromatic amines released from Azo dyes (each individual amine))	-	2410	-
Cl-8 (IS 17011, Table-1 (iii)(Aromatic amines released from Azo dyes (each individual amine))	-	2410	-
Cl-8(IS 17011, Table-1 (iv)(Chromium (VI))	-	1500	-
Cl-8 (IS 17011, Table-1 (v)(Dimethyl fumarate (DMFU))	-	4960	-
Cl-8 (IS 17011, Table-1 (vi)(Formaldehyde (free or released by partial hydrolysis))	-	2500	-
Cl-8 (IS 17011, Table-1 (vii)(Formaldehyde)	-	2500	-
Cl-8(IS 17011, Table-1 (viii)(Organotin compounds)	-	4960	-
Cl-8 (IS 17011, Table-1 (ix)(PCP-TeCP-TriCP polychlorophenols)	-	4980	-
Cl-8 (IS 17011, Table-1 (x)(pH)	-	350	-
Cl-8 (IS 17011, Table-1 (xi)(Phthalates (each individual phthalate))	-	3960	-
Cl-8 (IS 17011, Table-1 (xii)(Nickel, on skin contact)	-	5478	-
Cl- 5.2.8.1 (Amendment No. 2)(General)	-	200	-
Cl- 5.2.8.2 (Amendment No. 2)(Internal length of toecap)	-	200	-
Cl- 5.2.8.3 (Amendment No. 2)(Corrosion resistance)	-	1000	-
Cl- 5.2.9.5 (Amendment No. 2)(Breaking load and tag retention)	-	500	-
Cl- 5.2.9.6.1 (Amendment No. 2)(Abrasion resistance- Lace to lace)	-	1000	-
Cl- 5.2.9.6.2 (Amendment No. 2)(Abrasion resistance- Lace to eyelet)	-	1000	-
Cl- 5.2.10 (Amendment No. 2)(Force required to pull out the eyelets)	-	500	-
Cl- 5.2.12.1 (Amendment No. 2)(Insole- Material and thickness)	-	200	-
Cl- 5.2.12.2 (Amendment No. 2)(Insole- Abrasion resistance)	-	900	-
Cl- 5.2.12.3 (Amendment No. 2)(Insole- Water absorption and desorption)	-	900	-
Cl- 5.2.13.1 (Amendment No. 2)(Insock- Abrasion resistance)	-	1500	-
Cl- 5.2.13.2 (Amendment No. 2)(Insock- Water absorption and desorption)	-	900	-

-
-

7547

Cotecna Inspection India Private Limited, Gurugram

8166106

IS 5676 (1995)

Moulded solid rubber soles and heels - SpecificatlOn (Second Revision)

4900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5/5.3/5.3.1(REQUIREMENTS- Construction)	-	400	As per applicable clauses
5/5.1(REQUIREMENTS-General)	-	400	As per applicable clauses
5/5.6/5.6.1(REQUIREMENTS-Channel)	-	400	As per applicable clauses
5/5.7- Table2(REQUIREMENTS- Physical Requirements- as per IS 3400 (Part 1, Part 2, Part 4, Part 9, Part 10, Part 16))	-	400	As per applicable clauses
6(Marking and packing)	-	400	As per applicable clauses
8.1(Test methods)	-	400	As per applicable clauses
8.3(Measurement of thickness)	-	400	As per applicable clauses
Cl.6.1,6.2,6.3(Marking and packing)	-	200	-
8.1(Test Methods)	-	200	-
Cl.8.3(Measurement of thickness ")	-	200	-
5.5 (Amendment 1)(Thickness)	-	200	-
5.7 Table 2 i) (Amendment 1)(Relative Density)	-	300	-
5.7, Table 2 ii) (Amendment 1)(Hardness, degree, Shore A)	-	300	-
5.7, Table 2 iv) (Amendment 1)(Abrasion Resistance at applied force of 10 N)	-	1080	-
5.7, Table 2 v) (Amendment 1)(Tensile strength)	-	500	-
5.7, Table 2 vi) (Amendment 1)(Elongation at break)	-	500	-
5.7, Table 2 vii) (Amendment 1)(Tear strength (average force))	-	450	-
5.7, Table 2 iii) (Amendment 1)(Flexing resistance)	-	1000	-

-
-

7548

Cotecna Inspection India Private Limited, Gurugram

8166106

IS 6719 (1972)

Solid Pvc Soles And Heels

3800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.6.1(Hardness )	-	500	As per applicable clause
3.6 (vi)(Lead (as Pb) ppm)	-	500	As per applicable clause
3.6 (v)(Volatility, percent by means )	-	500	As per applicable clause
3.6 (iv)(Tear Strength a) Force Part b) Back Part )	-	500	As per applicable clause
3.6 (iii)(Elongation at break, percent )	-	500	As per applicable clause
3.6 (ii)(Tensile Strength )	-	500	As per applicable clause
3.6 (i)(Relative density )	-	500	As per applicable clause
Cl. 3.1,3.2,3.3,3.4,3.5(Material)	-	500	As per applicable clause
6 ,6.1,6.2,6.3(Test Method)	-	200	-
Cl. 3.1,3.2,3.3,3.4,3.5(Material)	-	200	-
Cl. 6.4(Measurement of thickness)	-	200	-
Table 1 (Flexing resistance)(Table 1 (Flexing resistance, Bennewart method, cut growth at the end of 30 000 cycles, mm, Max))	-	1000	-
Table 1 (Abrasion resistance)(Abrasion resistance at applied force of 10 N (volume loss), mm3, Max)	-	1080	-
Table 1 Cl. 3.6, Sl No (iii)(Volatility, Percent by mass)	-	800	-
Table 1 Cl. 3.6, Sl No (iv)("Lead (as Pb), Shoes for infants, children and boys and girls, ppm")	-	990	-
Table 1 Cl. 3.6, Sl No (iv)("Lead (as Pb), for other sized shoes, ppm ")	-	990	-

-
-

7549

Cotecna Inspection India Private Limited, Gurugram

8166106

IS 13893 (1994)

Polyurethane soles semirigid - specification

6200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.3.2(Ageing test)	-	500	As per applicable clause
4.3(Ross Flex test)	-	500	As per applicable clause
4.3(Flexural strength )	-	500	As per applicable clause
4.3(Abrasion Resistance)	-	500	As per applicable clause
4.3(Elongation at break)	-	500	As per applicable clause
4.3(Tensile Strength )	-	500	As per applicable clause
4.3(Hardness Shore(A))	-	500	As per applicable clause
4.3(Relative density )	-	500	As per applicable clause
4.2(Thickness )	-	500	As per applicable clause
4.1(Design)	-	500	As per applicable clause
5, 5.1, 5.2(Packing And Marking)	-	500	As per applicable clause
Cl.5, 5.1, 5.2(Packing And Marking)	-	200	-
4.2 (Amendment 2)(Thickness)	-	200	-
4.3.1 Table 1 i) (Amendment 2)(Relative Density)	-	300	-
4.3.1 Table 1 iii) (Amendment 2)(Abrasion Resistance at applied force of 10 N)	-	1080	-
4.3.1 Table 1 iv) (Amendment 2)(Flexing Resistance, Bennewart method)	-	1000	-
4.3.1 Table 1 v) (Amendment 2)(Hydrolysis Resistance, cut growth after 150000 flexes)	-	2000	-
4.3.1 Table 1 vi) (Amendment 2)(Tensile Strength)	-	500	-
4.3.1 Table 1 vii) (Amendment 2)(Elongation at break)	-	500	-
4.3.1 Table 1 viii) (Amendment 2)(Tear Strength (average force))	-	450	-
4.3.1 Table 1 ii) (Amendment 2)(Hardness, degree, Shore A)	-	300	-

-
-

7550

Cotecna Inspection India Private Limited, Gurugram

8166106

IS 6664 (1992)

Rubber microcellular sheets for soles and heels - Specification (First Revision)

6700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2(Flexing resistance )	-	400	As per applicable clause
4.2(Water absorption)	-	400	As per applicable clause
4.2(Heat Shrinkage )	-	400	As per applicable clause
4.2(Shrinkage at room temp)	-	400	As per applicable clause
4.2(Split tear strength)	-	400	As per applicable clause
4.2(Compression set)	-	400	As per applicable clause
4.2(Hardness (Shore A))	-	400	As per applicable clause
4.2(Density )	-	400	As per applicable clause
4.2(Size & Thickness )	-	400	As per applicable clause
4, Cl.4.1,4.1.1,4.1.2(Requirements)	-	400	As per applicable clause
Cl.4 Cl.4.1.3 And 8.3,Table1, i)(Relative density)	-	400	As per applicable clause
Cl.4.1.3 And 8.3,Table1, iii)(Hardness, Shore A durometer min)	-	400	As per applicable clause
Cl.4 Cl.4.1.3 And 8.3,Table1, iii)(Change in Hardness after ageing at 100±1°C for 24hr)	-	400	As per applicable clause
Cl.4 Cl.4.1.3 And 8.3,Table1, iv)(Compression set at constant stress percent, Max)	-	400	As per applicable clause
Cl.4 Cl.4.1.3 And 8.3,Table1, v)(Split tear strength, kg,Min)	-	400	As per applicable clause
Cl.4 Cl.4.1.3 And 8.3,Table1, vi)(Room Temperature shrinkage at 27±2°C for 2weeks, percent, Max)	-	400	As per applicable clause
Cl.4 Cl.4.1.3 And 8.3,Table 1, vi)(Heat shrinkage test at 100±1°C for 1 hour max)	-	400	As per applicable clause
Cl.4 Cl.4.1.3 And 8.3,Table1, viii)(Water absorption , percent by mass, Max)	-	400	As per applicable clause
Cl.4 Cl.4.1.3 And 8.3,Table 1, viii)(Flexing resistance: Maximum cut growth at 50 000 cycles)	-	400	As per applicable clause
5, 5.1(Marking)	-	400	As per applicable clause
6, 6.1(Packing)	-	400	As per applicable clause
"Cl.4 ,Cl.4.1,4.1.1,4.1.2(Requirements ")	-	200	-
Cl.4.1.3 And 8.3,Table1(i) Relative density)	-	300	-
Cl.4.1.3 And 8.3,Table1(ii) Hardness, Shore A durometer min)	-	300	-
Cl.4.1.3 And 8.3,Table1(iii) Change in Hardness after ageing at 100±1°C for 24hr)	-	1300	-
Cl.4.1.3 And 8.3,Table1(iv) Compression set at constant stress percent, Max)	-	1000	-
Cl.4.1.3 And 8.3,Table1(vi) Room Temperature shrinkage at 27±2°C for 2weeks, percent, Max)	-	1000	-
Cl.4.1.3 And 8.3,Table 1 vi(Heat shrinkage test at 100±1°C for 1 hour max)	-	1000	-
Cl.4.1.3 And 8.3,Table1(viii)Water absorption , percent by mass, Max)	-	500	-
Cl.4.1.3 And 8.3,Table1(ix)Flexing resistance)	-	1000	-
5, 5.1(Marking)	-	200	-
6, 6.1(Packing)	-	200	-
Cl.4.1.3 and 8.3,Table 1 ii(Thickness)	-	200	-
Cl.4.1.3 and 8.3,Table 1 vii(Abrasion resistance at applied force of 5 N)	-	1080	-

-
-

7551

Cotecna Inspection India Private Limited, Gurugram

8166106

IS 3735 (1996)

Canvas Shoes, Rubber Sole

18900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4.5 Consolidation Test IS 3400 (Part 5) : 1986 (From the quarter, cut a strip of 25.0 ± 0.5 mm width along the leagth of the boot and of sufficient length to permit separation over a length of 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100± 10mm per minute in accordance with IS 3400 (Part 5): 1986 or Static Dead Load Method as given in Annex C. The individual adhesion value for consolidation test shall not be less than 30N (3.0 kgf) for each of the teat piecea (see Note under 4.4).')	-	500	-
4.1.1 Upper, Sl No. (i) of Table 1(The upper shall consist of over layer of cotton, manmade or blended conforming' to the requirements given in Sl No. (i) of Table 1 as an overlayer and cotton drill conforming to the requirements given in Sl No. (ii) of Table 1, as an inner layer or lining. The two fabrics shall be firmly adhered together with rubber compound. )	-	500	-
Cl.4.1.1.1 Colour fastness(The dyed fabrics prescribed in 4.1.1 shall be fast todaylight and mechanical washing. Fastness to daylight shall be of rating 4 or better, when tested in accordance with IS 686 : 1985 or IS 2454: 1985. However in case of dispute the method prescribed in IS 686 : 1985 shall be considered as referee method.)	-	500	-
Cl.4.1.2 Binding Material(IS 1954 : 1990) (IS1969 : 1985)(Cotton tape NEWAR used as binding material shall conform to the requirements prescribed in col 3 of Table 2, when tested in accordance with the methods referred to in col 4 of the table.)	-	500	-
Cl.4.1.2.1 Anmex B.(Cotton, manmade or blended shall be used as binding material.' 'Coloured cotton tapes shall have fastness to day light of rating as and if agreed to between the purchaser and the supplier when tested in accordance with IS 686 : 1985. The black tapes shall be free from sulphur dyes when tested in accordance with Annex B.')	-	500	-
Cl.4.1.3.1( Sewing thread cotton, manmade or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other suitable thread shall have breaking load not less than above referred requirement of specification. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other suitable thread shall have breaking load not less than above referred requirement of specification.')	-	500	-
Cl.4.1.3.2 (IS 2454 : 1985) IS 765 : 1979 IS 971 : 1966( The colour of the threads shall be as agreedto between the purchaser and the supplier. The dyed threads shall conform to the following requirements or IS 686 : 1985'.)	-	500	-
Cl.4.1.4(.Brass, steel or aluminium eyelets of 7.5 mm diameter and wall thickness 0.30 to 0.35 mm shall be used.')	-	500	-
Cl.4.1.5 Laces( The shoes shall be provided with fabric braided laces either matching the shade of the upper or black or The length of the lace shall be 60 ± 3 cm )	-	500	-
Cl.4.1.5 Laces(and shallhave the breaking strength of not less than 250 N when tested between 18 cm grips in accordance with IS 1969 : 1985, the rate of traverse of power actuated grip being 300 mm/min.)	-	500	-
Cl.4.1.5 Laces Annex B(In case the laces are black, the same shall pass the test for freedom from sulpher dyes when tested in accordance with Annex B. The two ends of the lace shall be provided with suitable metal or plastic tips.)	-	500	-
Cl.4.1.6 Rubber Components(The rubber components shall conform to the requirements given in Table 4, when tested from finished boots.However in case it is not possible to cut the test pieces from the made up boots then 4.1.5.3 of IS 13695 : 1993 shall be followed.')	-	500	-
Cl.4.1.6.2 Ageing col 4 of Table 5.(The shoes shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the shoes shall conform to the physical requirements prescribed in col 4 of Table 5. )	-	500	-
Cl.4.1.6.2 Ageing (None of the rubber components of the shoes shall show any sign of tackiness or crack developed after ageing, when examined visually)	-	500	-
Cl.4.1.6.3 Thickness of components in Table 6.(Individual components of the shoes shall comply with the thickness and material requirements prescribed in Table 6.)	-	500	-
CL.4.2 Shape and Design IS 1638 : 1969(Cl 4.2.1 The shoes shall be made according to design and pattern as agreed to between the purchaser and the supplier. Size and fittings of the shoes shall be in accordance with IS 1638 : 1969 unless otherwise specified by the purchaser.)	-	500	-
Cl.4.2.2( The recommended design of canvas shoes is shown in Fig. 1.)	-	500	-
Cl.4.3 Construction Cl 4.3.1( The upper shall be stitched on a lock stitch machine and the number of stitches shall be 30 to 40 per dm.)	-	500	-
Cl.'4.3.2( Back of the upper shall be reinforced with a strip of upper material when there is a seam.')	-	500	-
Cl.4.3.3( The counter shall be stitched at the back, set from bottom of lining and bound flat on top edge with white/scoured binding material cut in bias and formed as a tape. T )	-	500	-
Cl.4.3.3(he number of stitches shall be 30 to 40 per decimetre. The counter binding shall meet the binding of the upper at the centre top edge of the heel.)	-	500	-
Cl.4.3.3(The edges of quarter shall be bound with dyed cotton binding material or matching to the colour of the upper, cut in bias and formed as a tape.)	-	500	-
Cl.4.3.4 (The vantp shall be strengthened with a rubber toe-cap (see Fig. 1).)	-	500	-
Cl.4.3.5( Five pairs of eyelets shall be fitted in each shoe. The eyelets shall be properly clenched without any distortion. It shall properly match the colour of the upper canvas, or as agreed to between the purchaser and the supplier.)	-	500	-
Cl.4.3.6( The shoes shall be free from folds, wrinkles in the upper, blisters, embedded foreign matters and excessive surface markings. In appearance, general workmanship, finish and all other respects, not defined in the standard, the shoes shall be similar to the sample approved by the purchaser, if any)	-	500	-
CL.4.3.7( The soles shall be of even substance and ofone layer only.)	-	500	-
Cl.4.3.8( A rubber foxing shall be fixed all round the sole and heel. The colour shall be as agreed to between the purchaser and the supplier. )	-	500	-
Cl.4.3.8(The foxing, not less than 18 mm wide, shall not extend beyond the edges of the sole at the bottom)	-	500	-
Cl.4.4 Adhesion Test(From the upper-foxing portion where it is adhered to the canvas, parallel to the waist of sole, cut a strip of length 100 mm and width 8 mm. Separate out the plies initially by breaking the bond to a length of about 75 mm. Carry out the test on two specimens in accordance with IS 3400 (Part 5) : 1986. There shall be no further separation within 1 minute at a load of 1 kg for each of the two specimens.)	-	500	-
CL.4.6 Mass(The mass of one pair of finished shoes of size 8 shall not exceed 750 g with an increase or decrease of 25 g for each bigger or smaller size respectively)	-	500	-
Cl.4.5 Consolidation Test IS 3400 (Part 5) : 1986 (From the quarter, cut a strip of 25.0 ± 0.5 mm width along the leagth of the boot and of sufficient length to permit separation over a length of 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100± 10mm per minute in accordance with IS 3400 (Part 5): 1986 or Static Dead Load Method as given in Annex C. The individual adhesion value for consolidation test shall not be less than 30N (3.0 kgf) for each of the teat piecea (see Note under 4.4).')	-	500	-
4.1.1 Upper, Sl No. (i) of Table 1(The upper shall consist of over layer of cotton, manmade or blended conforming' to the requirements given in Sl No. (i) of Table 1 as an overlayer and cotton drill conforming to the requirements given in Sl No. (ii) of Table 1, as an inner layer or lining. The two fabrics shall be firmly adhered together with rubber compound. )	-	500	-
Cl.4.1.1.1 Colour fastness(The dyed fabrics prescribed in 4.1.1 shall be fast todaylight and mechanical washing. Fastness to daylight shall be of rating 4 or better, when tested in accordance with IS 686 : 1985 or IS 2454: 1985. However in case of dispute the method prescribed in IS 686 : 1985 shall be considered as referee method.)	-	500	-
Cl.4.1.2 Binding Material(IS 1954 : 1990) (IS1969 : 1985)(Cotton tape NEWAR used as binding material shall conform to the requirements prescribed in col 3 of Table 2, when tested in accordance with the methods referred to in col 4 of the table.)	-	500	-
Cl.4.1.2.1 Anmex B.(Cotton, manmade or blended shall be used as binding material.' 'Coloured cotton tapes shall have fastness to day light of rating as and if agreed to between the purchaser and the supplier when tested in accordance with IS 686 : 1985. The black tapes shall be free from sulphur dyes when tested in accordance with Annex B.')	-	500	-
Cl.4.1.3.1( Sewing thread cotton, manmade or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other suitable thread shall have breaking load not less than above referred requirement of specification. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other suitable thread shall have breaking load not less than above referred requirement of specification.')	-	500	-
Cl.4.1.3.2 (IS 2454 : 1985) IS 765 : 1979 IS 971 : 1966( The colour of the threads shall be as agreedto between the purchaser and the supplier. The dyed threads shall conform to the following requirements or IS 686 : 1985'.)	-	500	-
Cl.4.1.4(.Brass, steel or aluminium eyelets of 7.5 mm diameter and wall thickness 0.30 to 0.35 mm shall be used.')	-	500	-
Cl.4.1.5 Laces( The shoes shall be provided with fabric braided laces either matching the shade of the upper or black or The length of the lace shall be 60 ± 3 cm )	-	500	-
Cl.4.1.5 Laces(and shallhave the breaking strength of not less than 250 N when tested between 18 cm grips in accordance with IS 1969 : 1985, the rate of traverse of power actuated grip being 300 mm/min.)	-	500	-
Cl.4.1.6 Rubber Components(The rubber components shall conform to the requirements given in Table 4, when tested from finished boots.However in case it is not possible to cut the test pieces from the made up boots then 4.1.5.3 of IS 13695 : 1993 shall be followed.')	-	500	-
Cl.4.1.6.2 Ageing (None of the rubber components of the shoes shall show any sign of tackiness or crack developed after ageing, when examined visually)	-	500	-
Cl.4.1.6.3 Thickness of components in Table 6.(Individual components of the shoes shall comply with the thickness and material requirements prescribed in Table 6.)	-	500	-
CL.4.2 Shape and Design IS 1638 : 1969(Cl 4.2.1 The shoes shall be made according to design and pattern as agreed to between the purchaser and the supplier. Size and fittings of the shoes shall be in accordance with IS 1638 : 1969 unless otherwise specified by the purchaser.)	-	500	-
Cl.4.2.2( The recommended design of canvas shoes is shown in Fig. 1.)	-	500	-
Cl.4.3 Construction Cl 4.3.1( The upper shall be stitched on a lock stitch machine and the number of stitches shall be 30 to 40 per dm.)	-	500	-
Cl.'4.3.2( Back of the upper shall be reinforced with a strip of upper material when there is a seam.')	-	500	-
Cl.4.3.3(he number of stitches shall be 30 to 40 per decimetre. The counter binding shall meet the binding of the upper at the centre top edge of the heel.)	-	500	-
Cl.4.3.3(The edges of quarter shall be bound with dyed cotton binding material or matching to the colour of the upper, cut in bias and formed as a tape.)	-	500	-
Cl.4.3.4 (The vantp shall be strengthened with a rubber toe-cap (see Fig. 1).)	-	500	-
Cl.4.3.5( Five pairs of eyelets shall be fitted in each shoe. The eyelets shall be properly clenched without any distortion. It shall properly match the colour of the upper canvas, or as agreed to between the purchaser and the supplier.)	-	500	-
Cl.4.3.6( The shoes shall be free from folds, wrinkles in the upper, blisters, embedded foreign matters and excessive surface markings. In appearance, general workmanship, finish and all other respects, not defined in the standard, the shoes shall be similar to the sample approved by the purchaser, if any)	-	500	-
CL.4.3.7( The soles shall be of even substance and ofone layer only.)	-	500	-
Cl.4.3.8( A rubber foxing shall be fixed all round the sole and heel. The colour shall be as agreed to between the purchaser and the supplier. )	-	500	-
Cl.4.4 Adhesion Test(From the upper-foxing portion where it is adhered to the canvas, parallel to the waist of sole, cut a strip of length 100 mm and width 8 mm. Separate out the plies initially by breaking the bond to a length of about 75 mm. Carry out the test on two specimens in accordance with IS 3400 (Part 5) : 1986. There shall be no further separation within 1 minute at a load of 1 kg for each of the two specimens.)	-	500	-
CL.4.6 Mass(The mass of one pair of finished shoes of size 8 shall not exceed 750 g with an increase or decrease of 25 g for each bigger or smaller size respectively)	-	500	-
4.8(Adhesion )	-	500	-
4.7(Consolidation test )	-	1000	-
4.6(Mass )	-	500	-
4.5(Finish )	-	500	-
4.4(Contruction )	-	500	-
4.3(Leg Height )	-	500	-
4.2(Design )	-	500	-
4.1.6.2(Thickness of components )	-	500	-
4.1.6.2(Ageing)	-	500	-
4.1.6(Compression set )	-	1000	-
4.1.6(Elongation at break )	-	1000	-
4.1.6(Tensile strength)	-	1000	-
4.1.6(Hardness (after accelerated ))	-	500	-
4.1.6(Flexing resistance test)	-	1000	-
4.1.6(Hardness )	-	500	-
4.1.6(Relative density)	-	500	-
4.1.5(Sulpher dyes content )	-	2000	-
4.1.5(Breaking Load )	-	1000	-
4.1.5(Length )	-	500	-
4.1.4(Thickness)	-	500	-
4.1.4(Size )	-	500	-
4.1.3(Color fastness to perspiration)	-	500	-
4.1.3(Colorfastness to washing)	-	500	-
4.1.3(Colorfastness to light )	-	1000	-
4.1.3(Single thread breaking load)	-	1000	-
4.1.3(Construction )	-	500	-
4.1.2(Colorfastness to light )	-	1000	-
4.1.2(Colorfastness to washing)	-	500	-
4.1.2(Breaking Strength )	-	1000	-
4.1.2(Width )	-	500	-
4.1.1.2(Colorfastness to washing)	-	500	-
4.1.1.1(Colorfastness to light )	-	1000	-
4.1.1 (Drill) (End & Picks/dm)	-	500	-
4.1.1 (Drill) (Colorfastness to light )	-	1000	-
4.1.1 (canvas )(End & Picks/dm)	-	500	-
4.1.1 (canvas )(Breaking Load )	-	1000	-
5, 5.1, Cl. 5.2, Cl. 5.2.1, Cl. 5.2.1.1(Packing and marking)	-	200	-
" CL. 5.1, Cl. 5.2, Cl. 5.2.1, Cl. 5.2.1.1(Packing and marking ")	-	200	-

-
-

7552

Cotecna Inspection India Private Limited, Gurugram

8166106

IS 15644 (2006)

Safety of electric toys

Safety of Electric Toys

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.0(Marking and instructions)	-	500	As per Applicable Clause
8.0(Power Input)	-	500	As per Applicable Clause
9.0(Heating and abnormal operation)	-	500	As per Applicable Clause
10.0(Electrical strength at operating temperature)	-	500	As per Applicable Clause
11.1(Moisture resistance)	-	500	As per Applicable Clause
11.2(Resistant to humidity)	-	500	As per Applicable Clause
12.0(Electric strength at room temperature)	-	500	As per Applicable Clause
13.0(Mechanical strength)	-	500	As per Applicable Clause
14.1(Construction)	-	500	As per Applicable Clause
14.2(Construction)	-	500	As per Applicable Clause
14.3(Construction)	-	500	As per Applicable Clause
14.4(Construction)	-	500	As per Applicable Clause
14.5(Construction)	-	500	As per Applicable Clause
14.6(Construction)	-	500	As per Applicable Clause
14.7(Construction)	-	500	As per Applicable Clause
14.8(Construction)	-	500	As per Applicable Clause
14.9(Construction)	-	500	As per Applicable Clause
14.1(Construction)	-	500	As per Applicable Clause
14.11(Construction)	-	500	As per Applicable Clause
14.12(Construction)	-	500	As per Applicable Clause
14.13(Construction)	-	500	As per Applicable Clause
14.14(Construction)	-	500	As per Applicable Clause
15.1(Protection of cords and wires)	-	500	As per Applicable Clause
15.2(Protection of cords and wires)	-	500	As per Applicable Clause
17 Table-1(Screws and connections)	-	500	As per Applicable Clause
17 Table-1(Nominal daimeter of screws made of insulating material)	-	500	As per Applicable Clause
18.0(Clearance and creepage distance)	-	500	As per Applicable Clause
19.1(Ball pressure test IEC 60695-10-2)	-	500	As per Applicable Clause
19.2.1(Glow wire test IEC 60695-2-11)	-	500	As per Applicable Clause
19.2.2(Needle flame test)	-	500	As per Applicable Clause
16.0(Components)	-	500	As per Applicable Clause
9873 (Part-9) 3(Vinyl in any part of the toy or childcare article that can be placed in mouth of a child under 4 years of age - a) Di-iso-Nonyl Phthalate (DINP), b) Di-iso-Decyl Phthalate (DIDP), c) Di-n-Octyl Phthalate (DNOP) - IS 9873 Part 6)	-	400	-
9873 (Part-9) 3(Vinyl in toys or childcare articles - a) Bis-(2-ethlyhexyl) Phthalates (DEHP), b) Di-Butyl phthalate (DBP), c) Benzyl butyl Phthalate (BBP) - IS 9873 Part 6)	-	400	-
9873 (Part-7) 4.10(Container - Containers used for finger paints shall not have a design that is likely to be mistaken by children with containers of foodstuffs or drinks)	-	2400	-
9873 (Part-7) 4.9(N-Nitrosamines - N-nitrosodiethanolamine (NDELA) - n EN 71–12:2013, 7.2.1 and Clause 8)	-	2400	-
9873 (Part-7) 4.8(shall only use binding agents, extenders, humectants and surfactants which are not classified with any of the health hazards set out in in 4.1 (hazards class 3.1 to 3.10))	-	2400	-
9873 (Part-7) 4.7(pH value - ISO 787-9)	-	2400	-
9873 (Part-7) 4.6 - Table 4(Taste and smell - Finger paints shall not be sweetened, flavoured or fragranced - Cl 4.6)	-	2400	-
9873 (Part-7) 4.5.2 - Table 3(Impurities - Benzo (α) pyrene - Annex C)	-	2400	-
9873 (Part-7) 4.5.2 - Table 3(IImpurities- Hexachlorobenzene - Annex C)	-	2400	-
9873 (Part-7) 4.5.2 - Table 3(Impurities - Polychlorinated biphenyls - Annex C)	-	2400	-
9873 (Part-7) 4.5.1.2 - Table 2(Total,carcinogenic primary aromatic amines - Annex C)	-	2400	-
9873 (Part-7) 4.5.1.2 - Table 2(Individual carcinogenic primary aromatic amines - Annex C)	-	2400	-
9873 (Part-7) 4.5.1.1 - Table 1(Primary aromatic amines - Annex C)	-	2400	-
9873 (Part-7) 4.4 (ref. Table 1 row 3 of ISO 8124-3-2010)(Selenium (Se) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	2400	-
9873 (Part-7) 4.4 (ref. Table 1 row 3 of ISO 8124-3-2010)(Mercury (Hg) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	2400	-
9873 (Part-7) 4.4 (ref. Table 1 row 3 of ISO 8124-3-2010)(Lead (Pb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	2400	-
9873 (Part-7) 4.4 (ref. Table 1 row 3 of ISO 8124-3-2010)(Chromium (Cr) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	2400	-
9873 (Part-7) 4.4 (ref. Table 1 row 3 of ISO 8124-3-2010)(Cadmium (Cd) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	2400	-
9873 (Part-7) 4.4 (ref. Table 1 row 3 of ISO 8124-3-2010)(Barium (Ba) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	2400	-
9873 (Part-7) 4.4 (ref. Table 1 row 3 of ISO 8124-3-2010)(Arsenic (As) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	2400	-
9873 (Part-7) 4.4 (ref. Table 1 row 3 of ISO 8124-3-2010)(Antimony (Sb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 43(Preservatives - Benzenemethanaminium, N,Ndimethyl-N-[2-[2-[4-(1,1,3,3,- tetramethylbutyl)phenoxy] ethoxy] ethyl]-, chloride (Benzethonium Chloride)- EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 42(Preservatives - Sodium N-hydroxymethyl-glycinate - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 41(Preservatives - 3-(p-Chlorophenoxy)-propane-1,2 diol (Chlorphenesin) - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 40(Preservatives - Pentane-1,5-dial (Glutaraldehyde, Glutaral) - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 39(Preservatives -Benzenecarboximidamide, 4,4’-(1,6-hexanediyl-bis-(oxy))-bis-(3-nitrobenzamidine) and its salts (including isethionate and phydroxybenzoate): hexamidine, hexamidine diisethionate, hexamidine paraben - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 38(Preservatives - N-(Hydroxymethyl)-N-(dihydroxymethyl-1,3-dioxo-2,5-imidazolidinyl-4)-N’-(hydroxymethyl) urea (Diazolidinyl Urea) - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 37(Preservatives - 4,4-Dimethyl-1,3-oxazolidine - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 36(Preservatives - Alkyl (C 12–22) trimethyl ammonium bromide and chloride: Behentrimonium chloride, cetrimonium bromide, cetrimonium chloride, laurtrimonium bromide, laurtrimonium chloride, steartrimonium bromide, steartrimonium chloride - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 35(Preservatives - N,N″-bis(4-chlorophenyl)-3,12-diimino-2,4,11,13-tetraazatetradecanediamidine and its digluconate, diacetate and dihydrochloride: Chlorhexidine, Chlorhexidine Diacetate, Chlorhexidine Digluconate Chlorhexidine Dihydrochloride (as chlorhexidine) - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 34(Preservatives - 2-Chloroacetamide - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 33(Preservatives - 2-Benzyl-4-chlorophenol (Chlorophene) - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 32(Preservatives - 2-methylisothiazol-3(2H)-one (MIT) - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 31(Preservatives - Mixture of 5-Chloro-2-methyl-isothiazol-3(2H)-one and 2-methylisothiazol-3(2H)-one with magnesium chloride and magnesium nitrate (of a mixture in the ratio 3:1 of 5-chloro-2-methylisothiazol 3(2H)-one and 2-methylisothiazol-3 (2H)-one) - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 30(Preservatives - 4-Isopropyl-m-cresol (o-Cymen-5-ol) - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 29(Preservatives - 2,2’-methylenebis(6-bromo-4-chlorophenol) (Bromochlorophene) - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 28(Preservatives - 1-Hydroxy-4-methyl-6-(2,4,4- trimethylpentyl) 2-pyridon and its monoethanolamine salt (Piroctone Olamine) - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 27(Preservatives - 1,3-Bis (hydroxymethyl)-5,5-dimethylimidazolidine-2,4-dione (DMDM Hydantoin) - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 26(Preservatives -1-(4-Chlorophenoxy)-1-(imidazol-1-yl)-3,3-dimethylbutan-2-one (Climbazole) - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 25(Preservatives - Methenamine-3-chloro-allylochloride (Quaternium-15) - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 24(Preservatives - Methenamine - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 23(Preservatives - 2-Phenoxyethanol - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 22(Preservatives -Poly(methylene),.alpha.,.omega.-bis[[[(aminoiminomethyl) amino]iminomethyl] amino]-, dihydrochloride (Polyaminopropyl biguanide) - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 21(Preservatives -N,N″-methylenebis[N′-[3-(hydroxymethyl)-2,5-dioxoimidazolidin-4-yl]urea] (Imidazolidinyl urea) - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 20(Preservatives - Chloroxylenol - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 19(Preservatives - 5-Chloro-2- (2,4- dichlorophenoxy) phenol (Triclosan) - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 18(Preservatives - 1-(4-Chlorophenyl)-3-(3,4-dichlorophenyl) urea (Triclocarban) - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 17(Preservatives - 2,4-Dichlorobenzyl alcohol - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 16(Preservatives - 2-Bromo-2-nitropropane-1,3-diol (Bronopol) - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 13(Preservatives - 3,3’-Dibromo-4,4’-hexamethylenedioxydi-benzamidine and its salts (including isethionate) (Dibromohexamidine isethionate) - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 12(Preservatives - Formic acid, sodium formate (as acid) - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 11(Preservatives - 3-Acetyl-6-methylpyran-2,4 (3H)-dione and its salts: Dehydroacetic acid, sodium dehydroacetate (as acid) - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 10(Preservatives -4-Hydroxybenzoic acid, methylparaben, potassium ethylparaben, potassium paraben, sodium methylparaben, sodium ethylparaben, ethylparaben, sodium paraben, potassium methylparaben, calcium paraben, phenylparaben (as acid) - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 9(Preservatives - Chlorobutanol - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 8(Preservatives - Inorganic sulfites and hydrogen-sulfites: Sodium sulfite, ammonium bisulfite, ammonium sulfite, potassium sulfite, potassium, hydrogen sulfite, sodium bisulfite, sodium metabisulfite, potassium metabisulfite (as free SO2) - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 7(Preservatives - Pyrithione zinc - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 6(Preservatives - Biphenyl-2-ol (o-Phenylphenol), sodium o-phenylphenate, potassium o-phenylphenate, MEA o-phenylphenate (expressed as the phenol) - EU Cosmetics Legislation)	-	2400	-
4.3 - Annex - D- Table D.1 - Ref 5(Preservatives - Paraformaldehyde (free-formaldehyde)- EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 4(Preservatives - Hexa-2,4-dienoic acid and its salts: Sorbic acid, calcium sorbate, sodium sorbate potassium sorbate (as acid) - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 3(Preservatives - Propionic acid,, ammonium propionate, calcium propionate, magnesium propionate, potassium propionate, sodium propionate (as acid) - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 2(Preservatives - Ammonium benzoate calcium benzoate, potassium benzoate, magnesium benzoate, MEA-benzoate, methyl benzoate, ethyl benzoate, propyl benzoate, butyl benzoate, isobutyl benzoate, isopropyl benzoate, phenyl benzoate (as acid) - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.3 - Annex - D- Table D.1 - Ref 1(Preservatives - Benzoic acid, sodium benzoate (as acid) - EU Cosmetics Legislation)	-	2400	-
9873 (Part-7) 4.2.2 - Table 1, 2(Finger Paint shall not contain Azo colourants that by cleavage of one or more azo groups can produce the primary aromatic amines - Annex C)	-	2400	-
9873 (Part-7) 4.2.1 (Colourants used in finger paint shall not have any of the health hazard classifications set out in 4.1 (hazard class 3.1 to 3.10) - ISO 8124)	-	2400	-
9873 (Part-3) 4.1 - Table 1(Selenium (Se) - Cl 7,8,9 )	-	300	-
9873 (Part-3) 4.1 - Table 1(Mercury (Hg) - Cl 7,8,9 )	-	300	-
9873 (Part-3) 4.1 - Table 1(Lead (Pb) - Cl 7,8,9 )	-	300	-
9873 (Part-3) 4.1 - Table 1(Chromium (Cr) - Cl 7,8,9 )	-	300	-
9873 (Part-3) 4.1 - Table 1(Cadmium (Cd) - Cl 7,8,9)	-	300	-
9873 (Part-3) 4.1 - Table 1(Barium (Ba) - Cl 7,8,9 )	-	300	-
9873 (Part-3) 4.1 - Table 1(Arsenic (As) - Cl 7,8,9 )	-	300	-
9873 (Part-3) 4.1 - Table 1(Antimony (Sb) - Cl 7,8,9)	-	300	-

-
-

7553

Cotecna Inspection India Private Limited, Gurugram

8166106

IS 15844 : Part 1 (2023)

SPORTS FOOTWEAR PART -1 GENERAL PURPOSEFirst Revision

110000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl No . 4.14, Table no. 1 of IS 17011(i)(Allergenic and carcinogenic disperse dyes)	-	4460	-
Cl No . 4.14, Table no. 1 of IS 17011(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	2610	-
Cl No . 4.14, Table no. 1 of IS 17011(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	2610	-
Cl No . 4.14, Table no. 1 of IS 17011(iv)(Chromium (VI))	-	1490	-
Cl No . 4.14, Table no. 1 of IS 17011(v)(Dimethyl fumarate (DMFU))	-	4950	-
Cl No . 4.14, Table no. 1 of IS 17011(vi)(Formaldehyde (free or released by partial hydrolysis))	-	4300	-
Cl No . 4.14, Table no. 1 of IS 17011(vii)(Formaldehyde)	-	4300	-
Cl No . 4.14, Table no. 1 of IS 17011(viii)(Organotin compounds)	-	6930	-
Cl No . 4.14, Table no. 1 of IS 17011(ix)(PCP-TeCP-TriCP polychlorophenols)	-	3470	-
Cl No . 4.14, Table no. 1 of IS 17011(x)(pH)	-	300	-
Cl No . 4.14, Table no. 1 of IS 17011(xi)(Phthalates (each individual phthalate))	-	3960	-
Cl No . 4.14, Table no. 1 of IS 17011(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	3470	-
4.3.1(Insole)	-	100	-
4.3.2(Toe spring height)	-	200	-
4.3.3(Upper to Mid Sole/Out Sole Bond Performance)	-	1080	-
4.3.4("Upper to Composite Sole Bond Performance (Applicable Only When the Sole is Composite)")	-	1080	-
4.3.5(Out Sole to Mid Sole (Multilayer) Bond Performance)	-	1080	-
4.3.6(Energy Absorption at Seat Region)	-	630	-
4.3.9(Slip Resistance)	-	1500	-
Cl No.4.4 , Table No. 2 , ii)(Tear strength (average force), Min, N)	-	450	-
Cl No.4.4 , Table No. 2 , iv) , a)(Water vapour permeability, mg/cm2h, Min)	-	630	-
Cl No.4.4 , Table No. 2 , iv) , b)(Water vapour coefficient, mg/cm2 , Min)	-	0	-
4.3.7(Complete Shoe Flexing)	-	1080	-
Cl No.4.4 , Table No. 2 , i) , a)(Flexing resistance, Dry condition)	-	1000	-
Cl No.4.4 , Table No. 2 , i) , b)(Flexing resistance, Wet condition)	-	1000	-
Cl No.4.4 , Table No. 2 , v)(Stitch tear strength (double hole), N/mm, Min)	-	450	-
Cl No.4.4 , Table No. 2 , vi)("Colour fastness to light (Optional) Grey scale rate, Min Rating: (Marring)")	-	1500	-
Cl No.4.4 , Table No. 2 , i)(Breaking strength, N/mm, Min)	-	450	-
Cl No.4.4 , Table No. 2 , ii)(Elongation at break, percent Min)	-	0	-
Cl No.4.4 , Table No. 2 , iii)(Tear strength, N, Min For Fabric: For all other materials)	-	450	-
Cl No.4.4 , Table No. 2 , iv) , a)(Flexing resistance, Dry condition)	-	1000	-
Cl No.4.4 , Table No. 2 , iv) , b)(Flexing resistance, ,Wet condition)	-	1000	-
Cl No.4.4 , Table No. 2 , v) , a)(Water vapour permeability, mg/cm2h, Min)	-	630	-
Cl No.4.4 , Table No. 2 , v) , b)("Water vapour coefficient, mg/cm2 , Min ")	-	630	-
Cl No.4.4 , Table No. 2 , vi)(Hydrolysis resistance)	-	2000	-
Cl No.4.4 , Table No. 2 , vii)(Bursting Strength, kg/cm2 , Min)	-	800	-
Cl No.4.5 , Table No. 3 , i)(Tear strength, N, Min)	-	450	-
Cl No.4.5 , Table No. 3 , ii)(Abrasion resistance, cycles)	-	1350	-
Cl No.4.5 , Table No. 3 , iii)("Colour fastness to rubbing (crocking), Grey scale rate with 10 rubs on dry or wet, Min")	-	450	-
Cl No.4.5 , Table No. 3 , iv)("Colour fastness to perspiration (contact method) Grey scale rate, Min")	-	700	-
Cl No.4.5 , Table No. 3 , v) , a)(Water vapour permeability, mg/cm2h, Min)	-	630	-
Cl No.4.5 , Table No. 3 , v) , b)("Water vapour coefficient, mg/cm2 , Min ")	-	0	-
Cl No.4.6 , Table No. 4 , i)(Thickness, mm, Min)	-	100	-
Cl No.4.6 , Table No. 4 , ii)(Flexing index, Min)	-	1000	-
Cl No.4.6 , Table No. 4 , iii)(Abrasion resistance, at 400 cycles)	-	900	-
Cl No.4.6 , Table No. 4 , iv) , a)(Water Absorption, mg/cm2 , Min)	-	630	-
Cl No.4.6 , Table No. 4 , iv) , b)(Water Desorption, percent, Min)	-	0	-
Cl No.4.7, Table No. 5 , i)(Thickness, mm, Min)	-	100	-
Cl No.4.7, Table No. 5 , ii)(Abrasion resistance, cycles)	-	1350	-
Cl No.4.7, Table No. 5 , iii) , a)(Water Absorption, mg/cm2 , Min)	-	630	-
Cl No.4.7, Table No. 5 , iii) , b)(Water Desorption, percent, Min)	-	0	-
Cl No.4.8 , Table No. 6 , i)(Abrasion resistance (Volume loss), mm3 , Max)	-	1080	-
Cl No.4.8 , Table No. 6 , ii)("Flexing resistance Belt Method at 90 diameter Mandrel or Bennewart method, cut growth, Max")	-	1080	-
Cl No.4.9 , Table No. 7 , i)(Compression set, percent, Max)	-	800	-
Cl No.4.9 , Table No. 7 , ii)(Split tear strength, kg/25 mm, Min)	-	450	-
Cl No.4.9 , Table No. 7 , iii)(Heat shrinkage, percent, Max)	-	800	-
Cl No.4.11 , Table No. 9 , i)(Peel strength, N/mm, Min)	-	2500	-
Cl No.4.11 , Table No. 9 , ii)(Shear strength, kPa , Min)	-	0	-
Cl No.4.12 , Table No. 10 , i)(Limit of useful extension, percent, Min)	-	1000	-
Cl No.4.13 , Table No. 11 , i)(Breaking strength of lace, N, Min)	-	450	-
Cl No.4.13 , Table No. 11 , ii)(Lace tag strength, N, Min)	-	450	-
Cl No.4.13 , Table No. 11 , iii)(Lace to lace abrasion,)	-	1000	-
Cl No.4.13 , Table No. 11 , v)(Strength of Buckle/Ski hook, N, Min)	-	800	-
Cl No.4.13 , Table No. 11 , vi)(Corrosion resistance)	-	900	-
Cl No.4.8 , Table No. 6 , iii)("Hydrolysis resistance, cut growth after 150 000 flexes, in mm, Max")	-	2700	-
4.3.8(Washability)	-	1500	-
Cl No.4.4 , Table No. 2 , iii) , a)("Colour fastness rubbing (To and fro) Grey scale rate, Min , Dry: (rubbing) Rating: (Marring and staining) ")	-	250	-
Cl No.4.4 , Table No. 2 , iii) , b)("Colour fastness rubbing (To and fro) Grey scale rate, Min , Wet: (rubbing) Rating: (Marring and staining)")	-	250	-
Cl No.4.13 , Table No. 11 , iv)("Colour fastness to water Gray Scale Rate, Min Rating")	-	450	-
Cl No.4.10 , Table No. 8 , i)(First dry collapsing load, hardness, N, Min)	-	500	-
Cl No.4.10 , Table No. 8 , ii)(Resilience, percent, Min)	-	500	-
Cl No.4.10 , Table No. 8 , iii)(Moisture resistance, percent, Min)	-	500	-
Cl No.4.10 , Table No. 8 , iv) , a)(Initial dry area shape retention, percent, Min)	-	500	-
Cl No.4.10 , Table No. 8 , iv) , b)(Area shape retention after 10th collapse, dry, percent, Min)	-	500	-
Cl-5, Table -1 S. No-(i) (Amendment No-1)(Insole)	-	200	-
Cl-5, Table -1 S. No- (ii) (Amendment No-1)(Toe spring height)	-	200	-
Cl-5, Table -1 S. No- (iii) (Amendment No-1)("Bond performance (a) Upper to sole/mid sole/composite sole (b) Interlayer bond strength")	-	1000	-
Cl-5, Table -1 S. No- (iv) (Amendment No-1)(Energy absorption at seat region)	-	600	-
Cl-5, Table -1 S. No- (v) (Amendment No-1)(Complete shoe flexing)	-	1200	-
Cl-5, Table -1 S. No-(vi) (Amendment No-1)(Washability)	-	2000	-
Cl-5, Table -1 S. No- (vii) (Amendment No-1)(Slip resistance, coefficient of friction (COF),)	-	2000	-
Cl-5, Table -1 S. No- (viii) (Amendment No-1)("Abrasion resistance a-Cellular sole b-Solid sole")	-	1080	-
Cl-5, Table -1 S. No- (x) (Amendment No-1)(Chemical requirements)	-	30000	-
Cl-5, Table -1 S. No- (xi) (Amendment No-1)(Hydrolysis resistance)	-	2000	-
Cl-5, Table -1 S. No- (xii) (Amendment No-1)(Lead content)	-	990	-
Cl-6, Table -2 S. No- (i) (Amendment No-1)(Tear strength)	-	450	-
Cl-6, Table -2 S. No- (ii) (Amendment No-1)("Colour fastness rubbing a-Dry: (rubbing) b-Wet: (rubbing)")	-	400	-
Cl-6, Table -2 S. No- (iii), a) (Amendment No-1)(Water vapour permeability)	-	630	-
Cl-6, Table -2 S. No- (iii), b) (Amendment No-1)(Water vapour coefficient)	-	630	-
Cl-6, Table -2 S. No- (iv),(Amendment No-1)(Stitch tear strength)	-	450	-
Cl-6, Table -2 S. No- (v),(Amendment No-1)(Colour fastness to light grey scale rate,)	-	1500	-
Cl-6, Table -3 S. No- (i),(Amendment No-1)(Breaking strength, N/mm, Min)	-	500	-
Cl-6, Table -3 S. No- (ii),(Amendment No-1)("Elongation at break a-Tighter direction b-Stretch direction")	-	500	-
Cl-6, Table -3 S. No- (iii),(Amendment No-1)("Tear strength, N, Min a) For fabric b) For all other materials")	-	450	-
Cl-6, Table -3 S. No- (iv),(Amendment No-1)("Flexing resistance a- Dry condition b-Wet condition")	-	800	-
Cl-6, Table -3 S. No- (v), a (Amendment No-1)(Water vapour permeability)	-	630	-
Cl-6, Table -3 S. No- (v), b (Amendment No-1)(Water vapour coefficient)	-	630	-
Cl-6, Table -3 S. No- (vi), (Amendment No-1)(Hydrolysis resistance)	-	2000	-
Cl-6, Table -3 S. No- (vii), (Amendment No-1)(Bursting strength)	-	800	-
Cl-6, Table -4 S. No- (i),(Amendment No-1)(Tear strength, N, Min)	-	400	-
Cl-6, Table -4 S. No- (ii),(Amendment No-1)("Abrasion resistance, cycles a- Dry condition b-Wet condition")	-	1500	-
Cl-6, Table -4 S. No- (iii),(Amendment No-1)(Colour fastness to rubbing , grey scale rate with 10 rubs on dry or wet, Min)	-	400	-
Cl-6, Table -4 S. No- (iv),(Amendment No-1)(Colour fastness to perspiration)	-	700	-
Cl-6, Table -4 S. No- (v), a (Amendment No-1)(Water vapour permeability)	-	630	-
Cl-6, Table -4 S. No- (v), b (Amendment No-1)(Water vapour coefficient)	-	630	-
Cl-6, Table -5 S. No- (i), (Amendment No-1)(Thickness, mm, Min)	-	200	-
Cl-6, Table -5 S. No-(ii), (Amendment No-1)(Flexing index, Min)	-	800	-
Cl-6, Table -5 S. No- (iv), a (Amendment No-1)(Water absorption)	-	900	-
Cl-6, Table -5 S. No- (iv), b (Amendment No-1)(Water desorption, percent)	-	800	-
Cl-6, Table -6 S. No- (i), (Amendment No-1)(Thickness, mm, Min)	-	200	-
Cl-6, Table -6 S. No- (ii), (Amendment No-1)("Abrasion resistance, cycles a- Dry condition b-Wet condition")	-	1500	-
Cl-6, Table -6 S. No- (iii),a (Amendment No-1)(Water absorption)	-	800	-
Cl-6, Table -6 S. No- (iv), b (Amendment No-1)(Water desorption, percent)	-	800	-
Cl-6, Table -7 S. No- (i), (Amendment No-1)(Flexing resistance (Belt method or Bennewart method))	-	1000	-
Cl-6, Table -7 S. No- (ii), (Amendment No-1)(Hydrolysis resistance, cut growth after flexes)	-	2000	-
Cl-6, Table -8 S. No- (i), (Amendment No-1)("Compression set, percent, Max a) For EVA b) For all other materials")	-	1000	-
Cl-6, Table -8 S. No- (ii), (Amendment No-1)(Split tear strength)	-	450	-
Cl-6, Table -8 S. No- (iii), (Amendment No-1)(Heat shrinkage)	-	800	-
Cl-6, Table -9 S. No- (i), (Amendment No-1)(First dry collapsing load, hardness)	-	1000	-
Cl-6, Table -9 S. No- (iii), (Amendment No-1)(Moisture resistance)	-	1000	-
Cl-6, Table -9 S. No- (iv), a (Amendment No-1)(Initial dry area shape retention)	-	1000	-
Cl-6, Table -9 S. No- (iv), b (Amendment No-1)(Area shape retention after 10th collapse)	-	2000	-
Cl-6, Table -10 S. No- (i), (Amendment No-1)("Peel strength a) Initial b) After 5 000 wear cycles")	-	2000	-
Cl-6, Table -10 S. No- (ii), (Amendment No-1)("Shear strength a) Initial b) After 5 000 wear cycles")	-	2000	-
Cl-6, Table -11 S. No- (i), (Amendment No-1)(Limit of useful extension)	-	1000	-
Cl-6, Table -12 S. No- (i), (Amendment No-1)(Breaking strength of lace)	-	500	-
Cl-6, Table -12 S. No- (ii), (Amendment No-1)(Lace tag strength)	-	500	-
Cl-6, Table -12 S. No- (iii), (Amendment No-1)(Lace to lace abrasion)	-	1000	-
Cl-6, Table -12 S. No- (iv), (Amendment No-1)(Colour fastness to water (for lace) (contact method))	-	500	-
Cl-6, Table -12 S. No- (iv), (Amendment No-1)(Colour fastness to water (for lace) (contact method))	-	500	-
Cl-6, Table -12 S. No (v), (Amendment No-1)(Strength of buckle/ski hook)	-	500	-
Cl-6, Table -12 S. No- (vi), (Amendment No-1)(Corrosion resistance)	-	1000	-
Cl-6, Table -5 S. No-(iii), (Amendment No-1)(Abrasion resistance,)	-	900	-

-
-

7554

Cotecna Inspection India Private Limited, Gurugram

8166106

IS 15844 : Part 2 (2023)

SPORTS FOOTWEAR PART -2 PERFORMANCE SPORTS FOOTWEAR

110000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.12, Table no. 1 of IS 17011,(i)(Allergenic and carcinogenic disperse dyes)	-	4460	-
7.12, Table no. 1 of IS 17011,(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	2610	-
7.12, Table no. 1 of IS 17011,(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	2610	-
7.12, Table no. 1 of IS 17011,(iv)(Chromium (VI))	-	1490	-
7.12, Table no. 1 of IS 17011,(v)(Dimethyl fumarate (DMFU))	-	4950	-
7.12, Table no. 1 of IS 17011,(vi)(Formaldehyde (free or released by partial hydrolysis))	-	4300	-
7.12, Table no. 1 of IS 17011,(vii)(Formaldehyde)	-	4300	-
7.12, Table no. 1 of IS 17011,(viii)(Organotin compounds)	-	6930	-
7.12, Table no. 1 of IS 17011,(ix)(PCP-TeCP-TriCP polychlorophenols)	-	3470	-
7.12, Table no. 1 of IS 17011,(x)(pH)	-	300	-
7.12, Table no. 1 of IS 17011,(xi)(Phthalates (each individual phthalate))	-	3960	-
7.12, Table no. 1 of IS 17011,(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	3470	-
7.1.1(Whole Footwear)	-	990	-
7.1.2(Upper to Mid Sole/Out Sole Bond Performance)	-	1080	-
7.1.3("Upper to Composite Sole Bond Performance (Applicable Only When the Sole is Composite)")	-	1080	-
7.1.4(Out Sole to Mid Sole (Multilayer) Bond Performance)	-	1080	-
7.1.5(Energy Absorption at Seat Region)	-	630	-
7.1.6(Complete Shoe Flexing)	-	1200	-
7.1.8(Slip Resistance)	-	1500	-
7.1.9(Heel Drop)	-	200	-
7.2 , Table No. 2 , i)(Flexing resistance)	-	1000	-
7.2 , Table No. 2 , ii)(Tear strength (average force))	-	450	-
7.2 , Table No. 2 , iii)("Colour fastness rubbing (To and fro) Grey scale rate Dry: (rubbing) Rating: (Marring and staining) ")	-	450	-
7.2 , Table No. 2 , iv) ,a)(Water vapour permeability)	-	630	-
7.2 , Table No. 2 , iv) ,b)(Water vapour coefficient)	-	0	-
7.2 , Table No. 2 , v)(Stitch tear strength (double hole))	-	450	-
7.2 , Table No. 2 , vi)("Colour fastness to light (Optional) Grey scale rate, Rating: (Marring)")	-	1500	-
7.2 , Table No. 2 , vii)(Tensile strength)	-	450	-
7.2 , Table No. 2 , viii)(Elongation at break,)	-	0	-
7.2 , Table No. 2 , ix)("Water penetration and water absorption after 60 Minutes Water absorption %, Max Water penetration Gms, Max")	-	600	-
7.2 , Table No. 2 , x)(Abrasion test (for unlined upper))	-	1350	-
7.2 , Table No. 3 , i)(Breaking strength "As per Method 1 of IS 7016 (Part 2)/ ISO 1421 : 2016 or ISO 17706")	-	450	-
7.2 , Table No. 3 , ii)(Elongation at break)	-	0	-
7.2 , Table No. 3 , iii)(Tear strength, N, Min For Fabric: For all other materials)	-	450	-
7.2 , Table No. 3 , iv)(Strength at needle perforation)	-	450	-
7.2 , Table No. 3 , v)("Flexing resistance, no crack/damage to coating/ lamination / upper material till prescribed cycles")	-	1000	-
7.2 , Table No. 3 , vi) , a)(Water vapour permeability,)	-	630	-
7.2 , Table No. 3 , vi) , b)("Water vapour coefficient, ")	-	0	-
7.2 , Table No. 3 , vii)(Hydrolysis resistance)	-	2000	-
7.2 , Table No. 3 , viii)(Colour fastness to light grey scale rate)	-	1500	-
7.2 , Table No. 3 , ix)(Bursting Strength,)	-	800	-
7.3 , Table No. 4 , i)(Tear strength,)	-	450	-
7.3 , Table No. 4 , ii)(Abrasion resistance, cycles)	-	1350	-
7.3 , Table No. 4 , iii)("Colour fastness to rubbing (crocking), Grey scale rate with 10 rubs on dry or wet, ")	-	450	-
7.3 , Table No. 4 , iv)("Colour fastness to perspiration (contact method) Grey scale rate, ")	-	700	-
7.3 , Table No. 4 , v) , a)(Water vapour permeability,)	-	630	-
7.3 , Table No. 4 , v) , b)("Water vapour coefficient, " As per IS 15298 (Part 1))	-	0	-
7.4 , Table No. 5 , i)(Thickness)	-	100	-
7.4 , Table No. 5 , ii)(Flexing index)	-	1000	-
7.4 , Table No. 5 , iii)(Abrasion resistance, at 400 cycles)	-	900	-
7.4 , Table No. 5 , iv) , a)(Water Absorption,)	-	630	-
7.4 , Table No. 5 , iv) , b)(Water Desorption)	-	0	-
7.5 , Table No. 6 , i)(Thickness)	-	100	-
7.5 , Table No. 6 , ii)(Abrasion resistance, cycles As per IS 15298 (Part 1))	-	1350	-
7.5 , Table No. 6 , iii) , a)(Water Absorption)	-	630	-
7.5 , Table No. 6 , iii) , b)(Water Desorption)	-	0	-
7.5 , Table No. 6 , iv)(Heat resistance shrinkage linear)	-	800	-
7.7 , Table No. 8 , i)(Compression set)	-	800	-
7.7 , Table No. 8 , ii)(Split tear strength,)	-	450	-
7.7 , Table No. 8 , iii)(Heat shrinkage,)	-	800	-
7.7 , Table No. 8 , iv)(Elongation at break,)	-	450	-
7.8 , Table No. 9 , v)(Peel strength)	-	600	-
7.9 , Table No. 10 , i)(Peel strength)	-	2500	-
7.9 , Table No. 10 , ii)(Shear strength)	-	0	-
7.10 , Table No. 11 , i)(Limit of useful extension,)	-	1000	-
7.10 , Table No. 11 , ii)(Needle strength,)	-	450	-
7.11 , Table No. 12 , i)(Breaking strength of lace,)	-	450	-
7.11 , Table No. 12 , ii)(Lace tag strength,)	-	450	-
7.11 , Table No. 12 , iii)(Lace to lace abrasion,)	-	1000	-
7.11 , Table No. 12 , iv)("Colour fastness to water Gray Scale Rate")	-	450	-
7.11 , Table No. 12 , v)(Strength of Buckle/Ski hook)	-	800	-
7.11 , Table No. 12 , vi)(Corrosion resistance)	-	900	-
7.1.7(Washability)	-	1500	-
7.6 , Table No. 7 , i)(Abrasion resistance (volume loss))	-	1350	-
7.6 , Table No. 7 , ii)(Flexing resistance)	-	1000	-
7.6 , Table No. 7 , iii)(Hydrolysis resistance, cut growth after 1 50 000 flexes)	-	2000	-
7.6 , Table No. 7 , iv)(Tear strength)	-	450	-
7.6 , Table No. 7 , v)(Tensile strength)	-	630	-
7.6 , Table No. 7 , vi)(Elongation at break)	-	0	-
7.6 , Table No. 7 , vii)(Compression set)	-	630	-
7.8 , Table No. 9 , i)(First dry collapsing load, hardness)	-	500	-
7.8 , Table No. 9 , ii)(Resilience)	-	500	-
7.8 , Table No. 9 , iii)(Moisture resistance)	-	500	-
7.8 , Table No. 9 , iv) , a)(Initial dry area shape retention)	-	500	-
7.8 , Table No. 9 , iv) , b)(Area shape retention after 10th collapse, dry)	-	500	-
7.12.2 (Amendment 1)(Lead content)	-	990	-

-
-

7555

Alpha Test House Services LLP (160), Sahibzada Ajit Singh Nagar

9138706

IS 9550 (2024)

Bright Steel Bars â Specification (Second Revision)

Bright Steel Bars

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(Supply of material and product designation)	-	15000	-
Cl-6(Chemical Composition)	-	15000	-
Cl-7(mechanical properties)	-	15000	-
Cl-8.1(Dimensions)	-	15000	-
Cl-8.2.1, Table-1(Cold drawn or heattreated and cold drawn)	-	15000	-
Cl-8.2.1, Table-1(Cold drawn, heat treated)	-	15000	-
Cl-8.2.1, Table-1(Peeled/turned)	-	15000	-
Cl-8.2.1, Table-1(Polished)	-	15000	-
Cl-8.2.1.1(Tolerances on dimensions)	-	15000	-
Cl-8.2.2, Table-2 (i)(Manufacturing lengtha)	-	15000	-
Cl-8.2.2, Table-2 (ii)(Stock lengtha)	-	15000	-
Cl-8.2.2, Table-2 (iii)(Cut to length)	-	15000	-
Cl-9(Surface condiotn)	-	15000	-
Cl-14(Marking)	-	15000	-
Clause. 6.0(chemical composition)	-	15000	-
Clause. 6.0(Sillicon)	-	15000	-
Clause. 6.0(Carbon)	-	15000	-
Clause. 6.0(Copper)	-	15000	-
Clause. 6.0(Manganese)	-	15000	-
Clause. 6.0(Molybdenum)	-	15000	-
Clause. 6.0(Chromium)	-	15000	-
Clause. 6.0(Nickel)	-	15000	-
Clause. 6.0(Sulphur)	-	15000	-
Clause. 6.0(Phosphorus)	-	15000	-
Clause. 6.0(Vanadium)	-	15000	-
Clause. 6.0(Titanium)	-	15000	-
Clause. 6.0(Boron)	-	15000	-
Clause. 6.0(Aluminium)	-	15000	-
Clause. 7.0(Brinell Hardness)	-	15000	-
Clause. 7.0(Tensile test)	-	15000	-
Clause. 7.0(Yeild stress)	-	15000	-
Clause. 7.0(Elongation)	-	15000	-
Clause. 8.0(Dimension)	-	15000	-
Clause. 8.0(Tolerence)	-	15000	-
clause. 9.0(Surface condition)	-	15000	-
clause. 9.0(Decarburization)	-	15000	-
clause.-10.0(Sampling)	-	15000	-
clause.- 11.0(other tests)	-	15000	-
Clause. -12.0(Retest)	-	15000	-
Clasue.- 13.0(Surface Protection)	-	15000	-
Clasue.- 14.0(Marking)	-	15000	-

31 Dec, 2029

-
Included w.e.f 13.02.2025

7556

Bharat Test House Pvt. Ltd. 1668 Sonipat

9168306

IS 16098 Part 1 (2013)

Structured-Wall Plastics Piping Systems for Non-Pressure Drainage and Sewerage Part 1 Pipes and Fittings With Smooth External Surface, Type A

90000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.3.1(Dimension of Pipes and Fittings Diameter of pipe)	-	500	-
6.3.2(Dimension of Pipes and Fittings Lengths of Pipe)	-	500	-
6.3.3(Dimension of Pipes and Fittings Diameters of Pipes and Spigots of Pipes orFittings)	-	500	-
7.0(Physical characteristics for pipes and fittings Appearance)	-	500	-
7.1.1(Physical characteristics for pipes and fittings Colour of Finished Pipes)	-	500	-
7.2(Physical characteristics for pipes and fittings )	-	500	-
7.3(Physical characteristics for pipes and fittings )	-	500	-
8.1.1(Mechanical Characteristics of Pipes General)	-	500	-
8.1.1(Mechanical Characteristics of Pipes General)	-	500	-
8.1.2 (a)(Mechanical Characteristics of Pipes Ring Flexibility)	-	500	-
8.1.2 (b)(Mechanical Characteristics of Pipes Ring Flexibility)	-	500	-
8.1.2 (c)(Mechanical Characteristics of Pipes Ring Flexibility)	-	500	-
8.1.2 (d)(Mechanical Characteristics of Pipes Ring Flexibility)	-	500	-
8.1.2 (e)(Mechanical Characteristics of Pipes Ring Flexibility)	-	500	-
8.2.1(Mechanical Characteristics of Fittings General)	-	500	-
8.2.1(Mechanical Characteristics of Fittings General)	-	500	-
8.2.2(Mechanical Characteristics of Fittings)	-	500	-
8.3(Joints)	-	500	-
9 (Table 12)(Performance Requirements)	-	2000	-
9 (Table 12)(Performance Requirements)	-	2000	-
9 (Table 12)(Performance Requirements)	-	2000	-
11.1(Marking General)	-	500	-
11.2.1(Minimum Required Marking Pipes)	-	500	-
11.2.1(Minimum Required Marking Pipes)	-	500	-
11.2.1(Minimum Required Marking Pipes)	-	500	-
11.2.1(Minimum Required Marking Pipes)	-	500	-
11.2.1(Minimum Required Marking Pipes)	-	500	-
11.2.2(Minimum Required Marking Fittings)	-	500	-
11.2.2(Minimum Required Marking Fittings)	-	500	-
11.2.2(Minimum Required Marking Fittings)	-	500	-
11.2.2(Minimum Required Marking Fittings)	-	500	-
11.2.2(Minimum Required Marking Fittings)	-	500	-
11.2.2(Minimum Required Marking Fittings)	-	500	-
5.0(Composition of the material)	-	5000	-
5.1(Composition of the material)	-	5000	-
5.2 Table 1(Composition of the material- Resistance to internal hydrostatic Pipe material (1) 1 000 IS 12235 No seepage, cracking, pressure at 60ºC)	-	5000	-
5.3(Composition of the material)	-	5000	-
5.4(Composition of the material)	-	5000	-
6.0(DESIGNATION OF WALL CONSTRUCTIONS AND EXAMPLES OF TYPICAL JOINTING METHODS )	-	500	-
6.1(Wall Construction Designated as Type A)	-	500	-
6.2(Deswignation)	-	500	-
6.3(Dimensions of pipes and fittings)	-	500	-
6.3.1 Table 2(Mean outside diameter)	-	500	-
6.3.2 Table 3(Wall thickness)	-	500	-
6.3.3 Fig 2(Length of pipe)	-	500	-
6.3.4,Table 4,5(Dimensions of Integral sckets and spigot ends)	-	500	-
6.3.4.1(Wall thickness of sockets)	-	500	-
6.3.4.2(Fabricated fittings)	-	500	-
6.3.4.3(Rotational moulded fittings)	-	500	-
6.3.4.4(Type of fittings)	-	500	-
7.0(Physical characteristics of pipes)	-	1000	-
7.1(Appearance)	-	500	-
7.2(Colour )	-	500	-
7.3(Vicat softening temperature of pipes)	-	1000	-
7.4(Resistance to Dichloromethane)	-	2000	-
7.5(longitudinal reversion)	-	1000	-
8.0(Physical characteristics of fittings)	-	1000	-
8.1(Appearance and colour)	-	500	-
8.2(Vicat softening temperature of fittings)	-	1000	-
8.3(Effect of Heating (Stress Relief Test))	-	1000	-
9.0(Mechanical characteristics ofpipes)	-	1000	-
9.1(Ring stiffness)	-	1000	-
9.2(Resistance to external blows at o C)	-	1000	-
9.3(Ring flexibility)	-	1000	-
9.4(Creep ratio)	-	1000	-
10.0(Mechanical Characteristics of fittings)	-	1000	-
10.1(Impact Strength of Injection Moulded and Fabricated Fittings)	-	1000	-
11.0(Joints)	-	1000	-
11.1(Elastomeric Sealing Rings)	-	1000	-
11.2(Solvent cement)	-	1000	-
12.0(PERFORMANCE REQUIREMENTS)	-	1000	-
12.1(Elastomeric Sealing Ring Joints)	-	1000	-
12.1.1(Tightness of Elastomeric Sealing Ring Joints (Water pressure))	-	1000	-
12.1.2(Tightness of Elastomeric Sealing Ring Joints (Internal Vaccum ))	-	1000	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	1000	-
12.2(Solvent cement joints)	-	1000	-
12.2.1(Tightness of Solvent cemented Ring Joints )	-	1000	-
12.2.2(Tightness of Solvent cemented Ring Joints (Vaccum pressure))	-	1000	-
6.3.1(Dimension of Pipes and Fittings Diameter of pipe)	-	500	-
6.3.2(Dimension of Pipes and Fittings Lengths of Pipe)	-	500	-
6.3.3(Dimension of Pipes and Fittings Diameters of Pipes and Spigots of Pipes orFittings)	-	500	-
7.0(Physical characteristics for pipes and fittings Appearance)	-	500	-
7.1.1(Physical characteristics for pipes and fittings Colour of Finished Pipes)	-	500	-
7.2(Physical characteristics for pipes and fittings )	-	500	-
7.3(Physical characteristics for pipes and fittings )	-	1000	-
8.1.1(Mechanical Characteristics of Pipes General)	-	1000	-
8.1.1(Mechanical Characteristics of Pipes General)	-	1000	-
8.1.2 (a)(Mechanical Characteristics of Pipes Ring Flexibility)	-	1000	-
8.1.2 (b)(Mechanical Characteristics of Pipes Ring Flexibility)	-	1000	-
8.1.2 (c)(Mechanical Characteristics of Pipes Ring Flexibility)	-	1000	-
8.1.2 (d)(Mechanical Characteristics of Pipes Ring Flexibility)	-	1000	-
8.1.2 (e)(Mechanical Characteristics of Pipes Ring Flexibility)	-	1000	-
8.2.1(Mechanical Characteristics of Fittings General)	-	1000	-
8.2.1(Mechanical Characteristics of Fittings General)	-	1000	-
8.2.2(Mechanical Characteristics of Fittings)	-	1000	-
8.3(Joints)	-	1000	-
9 (Table 12)(Performance Requirements)	-	1000	-
9 (Table 12)(Performance Requirements)	-	1000	-
9 (Table 12)(Performance Requirements)	-	1000	-
11.1(Marking General)	-	500	-
11.2.1(Minimum Required Marking Pipes)	-	500	-
11.2.1(Minimum Required Marking Pipes)	-	500	-
11.2.1(Minimum Required Marking Pipes)	-	500	-
11.2.1(Minimum Required Marking Pipes)	-	500	-
11.2.1(Minimum Required Marking Pipes)	-	500	-
11.2.2(Minimum Required Marking Fittings)	-	500	-
11.2.2(Minimum Required Marking Fittings)	-	500	-
11.2.2(Minimum Required Marking Fittings)	-	500	-
11.2.2(Minimum Required Marking Fittings)	-	500	-
11.2.2(Minimum Required Marking Fittings)	-	500	-
11.2.2(Minimum Required Marking Fittings)	-	500	-
6.3.4 Table 4 & 5(Dimensions of Integral Socket and spigot ends)	-	500	-
6.3.4 Table 4 & 5(Outside diameter (dsm) min)	-	500	-
6.3.4 Table 4 & 5(C max)	-	500	-
7.1.1(Colour of finished pipes)	-	500	-
12.1.1(Tightness of Elastomeric Sealing Ring Joints (Water Pressure))	-	1000	-
12.1.2(Tightness of Elastomeric Sealing Ring Joints (Internal Vacuum))	-	1000	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	1000	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	1000	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	1000	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	1000	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	1000	-
7.6(7.6 Effect on Water)	-	2000	-
8.4(Effect on Water)	-	2000	-
5.2 Table 1(Composition of the material- Resistance to internal hydrostatic Pipe material (1) 1 000 IS 12235 No seepage, cracking, pressure at 60ºC)	-	0	-
6.3.4 Table 4 & 5(Dimensions of Integral Socket and spigot ends)	-	0	-
6.3.4 Table 4 & 5(Outside diameter (dsm) min)	-	0	-
6.3.4 Table 4 & 5(C max)	-	0	-
7.1.1(Colour of finished pipes)	-	0	-
12.1.1(Tightness of Elastomeric Sealing Ring Joints (Water Pressure))	-	0	-
12.1.2(Tightness of Elastomeric Sealing Ring Joints (Internal Vacuum))	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
7.6(7.6 Effect on Water)	-	0	-
8.4(Effect on Water)	-	0	-
5.2 Table 1(Composition of the material- Resistance to internal hydrostatic Pipe material (1) 1 000 IS 12235 No seepage, cracking, pressure at 60ºC)	-	0	-
6.3.4 Table 4 & 5(Dimensions of Integral Socket and spigot ends)	-	0	-
6.3.4 Table 4 & 5(Outside diameter (dsm) min)	-	0	-
6.3.4 Table 4 & 5(C max)	-	0	-
7.1.1(Colour of finished pipes)	-	0	-
12.1.1(Tightness of Elastomeric Sealing Ring Joints (Water Pressure))	-	0	-
12.1.2(Tightness of Elastomeric Sealing Ring Joints (Internal Vacuum))	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
7.6(7.6 Effect on Water)	-	0	-
8.4(Effect on Water)	-	0	-
5.2 Table 1(Composition of the material- Resistance to internal hydrostatic Pipe material (1) 1 000 IS 12235 No seepage, cracking, pressure at 60ºC)	-	0	-
6.3.4 Table 4 & 5(Dimensions of Integral Socket and spigot ends)	-	0	-
6.3.4 Table 4 & 5(Outside diameter (dsm) min)	-	0	-
6.3.4 Table 4 & 5(C max)	-	0	-
7.1.1(Colour of finished pipes)	-	0	-
12.1.1(Tightness of Elastomeric Sealing Ring Joints (Water Pressure))	-	0	-
12.1.2(Tightness of Elastomeric Sealing Ring Joints (Internal Vacuum))	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
7.6(7.6 Effect on Water)	-	0	-
8.4(Effect on Water)	-	0	-

-
Included w.e.f 09.04.2025

7557

BIS, Patna Branch Laboratory (PBL)

None

IS 14650 (2023)

UNALLOYED AND ALLOYED STEEL INGOT AND SEMI-FINISHED PRODUCTS FOR RE-ROLLING PURPOSES - SPECIFICATION (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause - 7.1 (CARBON)	-
Clause - 7.1 (SULPHUR)	-
Clause - 7.1 (PHOSPHURS)	-
Clause - 7.1 (MANGANESE)	-
Clause.7.1 (Silicon)	-
Clause - 7.1 (NITROGEN)	-
Clause.7.1 (Carbon Equbalant)	-

-
Testing facility for high manganese steel matrix not available.

7558

Unique Test House LLP

9134536

IS 17875 (2022)

Stainless Steel seamless pipes and tubes for general service

ALL SIZE GRADE DESIGNATION

16000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.0 (Table No.- 1)(Chemical Composition,% - IS 228)	-	700	-
10.1 (Table No.- 4)(Tensile Test,Mpa - IS 1608)	-	1000	-
11(Transverse Tension Test,%)	-	1000	-
12 (Table No.- 5)(Hardness Test,HRC,HRB&BHN- IS 1500 (Part 1) or IS 1586 (Part 1))	-	1500	-
13 (Table No.- 7)(Flaring Test)	-	500	-
14(Flattaning Test-IS 2328)	-	500	-
15.1 (Table No.- 8)(Grain Size,No.-IS 4748)	-	500	-
17(Leak Tighteness Test)	-	3000	-
18("Corrosion Test-IS 10461 (Part 1) or IS 10461 (Part 2)")	-	3000	-
19(Eddy current test & Air under water)	-	1000	-
21(Workmanship, Finish and Appearance)	-	500	-
22(Repair by Welding or Grinding)	-	500	-
23 (Table No.- 9,10&11)(Dimensions and Tolerances,mm)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Carbon)	-	700	-
"Clause 8.1 and 8.2 - Table 1"(Silicon)	-	700	-
"Clause 8.1 and 8.2 - Table 1"(Mangnese)	-	700	-
"Clause 8.1 and 8.2 - Table 1"(Nickel)	-	700	-
"Clause 8.1 and 8.2 - Table 1"(Chromium)	-	700	-
"Clause 8.1 and 8.2 - Table 1"(Molybdenum)	-	700	-
"Clause 8.1 and 8.2 - Table 1"(Sulphur)	-	700	-
"Clause 8.1 and 8.2 - Table 1"(Phosphorous)	-	700	-
"Clause 8.1 and 8.2 - Table 1"(Nitrogen)	-	3000	-
"Clause 8.1 and 8.2 - Table 1"(Copper)	-	700	-
"Clause 8.1 and 8.2 - Table 1"(Aluminium)	-	2000	-
"Clause 8.1 and 8.2 - Table 1"(Titanium)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Niobium)	-	500	-
"Clause 18 IS 10461(Part 1)"(Corrosion Test)	-	2000	-
Clause 10.1 - Table 4(Tensile Strength)	-	1000	-
Clause 10.1 - Table 4(Percent Elongation)	-	500	-
Clause 11(Transverse Tension Test)	-	500	-
Clause 12(Hardness Test)	-	1000	-
Clause 13(Flaring Test)	-	500	-
Clause 14(Flattening Test)	-	500	-
Clause 15(Grain Size)	-	500	-
Clause 17(Leak Tightness Test)	-	500	-
"Clause 18 IS 10461(Part 2)"(Corrosion Test)	-	2000	-
Clause 21(Workmanship, Finish & Appearance)	-	500	-
Clause 23 Annexure A, Table 9 Table 10(Dimensions & Tolerances)	-	500	-
10.2(Hardness test IS 1500 (part-1):2019)	-	1000	-
12.2(Flaring test IS 17878:2022)	-	500	-
16(Sampling)	-	500	-
24(Marking)	-	200	-
"Clause 8.1 and 8.2 - Table 1"(W)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Ta)	-	500	-
"Clause 8.1 and 8.2 - Table 2"(V)	-	500	-

07 Sep, 2028

-
Included.w.e.f.31.01.2025

7559

BIS, Central Laboratory (CL)

None

IS 11536 (2022)

Processed Cereal Based Complementary Foods ? Specification ( Third Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 4.7.2 and 4.10,Table 1 ,Sl No i) (Moisture)	-
Clause 4.7.2 and 4.10,Table 1 ,Sl No ii) (Total Protein)	-
Clause 4.7.2 and 4.10,Table 1 ,Sl No iii) (Total Fat)	-
Clause 4.7.2 and 4.10,Table 1 ,Sl No iV) (Total Carbohydrates)	-
Clause 4.7.2 and 4.10,Table 1 ,Sl No v) (Total Ash)	-
4.7.2, Table 1 (vi) (Ash insoluble in dilute hydrochloric acid-Annex D IS 14433)	-
Clause 4.7.2 and 4.10,Table 1 ,Sl No vii) (Iron)	-
Clause 4.7.2 and 4.10,Table 1 ,Sl No xi) (Crude fibre (on dry basis))	-
4.7.2, Table 1 (xx) (Zinc - 15 of IS 1699 or ISO 15151 or ISO 21424)	-
Clause 4.7.2 and 4.10,Table 1 ,Sl No xxiii) (Selenium)	-
Clause 4.13,Table 3 ,Sl No i) (Lead)	-
Clause 4.13,Table 3 ,Sl No ii) (Copper)	-
Clause 4.13,Table 3 ,Sl No iii) (Arsenic)	-
4.13, Table 3 (iv) (Tin - ISO 14377)	-
4.13, Table 3 (v) (Cadimum - 15 of IS 1699 or AOAC 2015.01)	-
"4.10 Table 2 (v) " (Salmonella sp.-IS 5887 (Part 3))	-
"4.10 Table 2 (i) " (Aerobic plate count-IS 5402 (Part 1))	-
"4.10 Table 2 (ii) " (Coliform count-IS 5401 (Part 1))	-
Clause 4.10,Table 2 ,Sl No iii) (Staphylococcus aureus (Coagulase positive))	-
"4.10 Table 2 (iv) " (Yeast & mould count-IS 5403)	-
"4.10 Table 2 (vi) " (Listeria monocytogenes-IS 14988 (Part 1))	-
"4.10 Table 2 (vii) " (Bacillus cereus-IS 5887 (Part 6))	-
"4.10 Table 2 (viii)" (Sulphite reducing clostridia-ISO 15213)	-
"4.10 Table 2 (ix)" (Escherichia coli-IS 5887 (Part 1))	-

-
-

7560

Gravitas Laboratories Private Limited, Greater Noida

8182606

IS 4454 : Part 1 (2001)

Steel wire for mechanical springs - Specification: Part 1 cold drawn unalloyed steel wire (Third Revision)

9500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8(Workmanship)	-	200	-
Cl 9(Diameter & Difference Between Two Reading On Any Two Diameters)	-	200	-
Cl 10(Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test & Decarburization Test)	-	200	-
Cl 8(Workmanship)	-	200	-
Cl 9(Diameter & Difference Between Two Reading On Any Two Diameters)	-	250	-
Cl 10(Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test & Decarburization Test)	-	3000	-
7.1, 7.2(copper)	-	200	-
7.1, 7.2(Vanadium)	-	200	-
7.1, 7.2(phosphorus)	-	200	-
7.1, 7.2(sulphur)	-	200	-
7.1, 7.2(manganese)	-	2002	-
7.1, 7.2(silicon )	-	200	-
7.1, 7.2(carbon)	-	200	-
7.1, 7.2(copper)	-	200	-
7.1, 7.2(Chromium)	-	200	-
7.1, 7.2(phosphorus)	-	200	-
7.1, 7.2(sulphur)	-	200	-
7.1, 7.2(manganese)	-	200	-
7.1, 7.2(silicon )	-	200	-
7.1, 7.2(carbon)	-	200	-
7.1, 7.2(copper)	-	200	-
7.1, 7.2(Chromium)	-	200	-
7.1, 7.2(phosphorus)	-	200	-
7.1, 7.2(sulphur)	-	200	-
7.1, 7.2(manganese)	-	200	-
7.1, 7.2(silicon )	-	200	-
7.1, 7.2(carbon)	-	200	-
7.1, 7.2(copper)	-	200	-
7.1, 7.2(Vanadium)	-	200	-
7.1, 7.2(Chromium)	-	200	-
7.1, 7.2(phosphorus)	-	200	-
7.1, 7.2(sulphur)	-	200	-
7.1, 7.2(manganese)	-	200	-
7.1, 7.2(silicon )	-	200	-
7.1, 7.2(carbon)	-	200	-
7.1, 7.2(copper)	-	200	-
7.1, 7.2(Vanadium)	-	200	-
7.1, 7.2(Chromium)	-	200	-
7.1, 7.2(phosphorus)	-	200	-
7.1, 7.2(sulphur)	-	200	-
7.1, 7.2(manganese)	-	200	-
7.1, 7.2(silicon )	-	200	-
7.1, 7.2(carbon)	-	200	-
7.1, 7.2(copper)	-	200	-
7.1, 7.2(Vanadium)	-	200	-
7.1, 7.2(Chromium)	-	200	-
7.1, 7.2(phosphorus)	-	200	-
7.1, 7.2(sulphur)	-	200	-
7.1, 7.2(manganese)	-	200	-
7.1, 7.2(silicon )	-	200	-
7.1, 7.2(carbon)	-	200	-
7.1, 7.2(copper)	-	200	-
7.1, 7.2(Vanadium)	-	200	-
7.1, 7.2(Chromium)	-	200	-
7.1, 7.2(phosphorus)	-	200	-
7.1, 7.2(sulphur)	-	200	-
7.1, 7.2(manganese)	-	200	-
7.1, 7.2(silicon )	-	200	-
7.1, 7.2(carbon)	-	200	-
7.1, 7.2(copper)	-	200	-
7.1, 7.2(Vanadium)	-	200	-
7.1, 7.2(Chromium)	-	200	-
7.1, 7.2(phosphorus)	-	200	-
7.1, 7.2(sulphur)	-	200	-
7.1, 7.2(manganese)	-	200	-
7.1, 7.2(silicon )	-	200	-
7.1, 7.2(carbon)	-	200	-
7.1, 7.2(copper)	-	200	-
7.1, 7.2(Vanadium)	-	200	-
7.1, 7.2(Chromium)	-	200	-
7.1, 7.2(phosphorus)	-	200	-
7.1, 7.2(sulphur)	-	200	-
7.1, 7.2(manganese)	-	200	-
7.1, 7.2(silicon )	-	200	-
7.1, 7.2(carbon)	-	200	-
7.1, 7.2(copper)	-	200	-
7.1, 7.2(phosphorus)	-	200	-
7.1, 7.2(sulphur)	-	200	-
7.1, 7.2(manganese)	-	200	-
7.1, 7.2(silicon )	-	200	-
7.1, 7.2(carbon)	-	200	-
7.1, 7.2(copper)	-	200	-
7.1, 7.2(phosphorus)	-	200	-
7.1, 7.2(sulphur)	-	200	-
7.1, 7.2(manganese)	-	200	-
7.1, 7.2(silicon )	-	200	-
7.1, 7.2(carbon)	-	200	-
7.1, 7.2(copper)	-	200	-
7.1, 7.2(phosphorus)	-	200	-
7.1, 7.2(sulphur)	-	200	-
7.1, 7.2(manganese)	-	200	-
7.1, 7.2(silicon )	-	200	-
7.1, 7.2(carbon)	-	200	-
7.1, 7.2(nitrogen)	-	200	-
7.1, 7.2(micro alloy)	-	200	-
7.1, 7.2(cu + cr+ni)	-	200	-
7.1, 7.2(sulphur + phosphorus)	-	200	-
7.1, 7.2(copper)	-	200	-
7.1, 7.2(phosphorus)	-	200	-
7.1, 7.2(sulphur)	-	200	-
7.1, 7.2(manganese)	-	200	-
7.1, 7.2(silicon )	-	200	-
7.1, 7.2(carbon)	-	200	-
7.1, 7.2(cu + cr + ni)	-	200	-
7.1, 7.2(sulphur + phosphorus)	-	200	-
7.1, 7.2(copper)	-	200	-
7.1, 7.2(phosphorus)	-	200	-
7.1, 7.2(sulphur)	-	200	-
7.1, 7.2(manganese)	-	200	-
7.1, 7.2(silicon )	-	200	-
7.1, 7.2(carbon)	-	200	-
Cl 10(Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test & Decarburization Test)	-	3000	-
Cl 9(Diameter & Difference Between Two Reading On Any Two Diameters)	-	200	-
Cl 8(Workmanship)	-	200	-
Cl 10(Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test & Decarburization Test)	-	3000	-
Cl 9(Diameter & Difference Between Two Reading On Any Two Diameters)	-	200	-
Cl 8(Workmanship)	-	200	-
11(Coating and surface finish)	-	200	-
11(Coating & Surface finish)	-	200	-
8(Freedom from defects)	-	200	-
11(Surface finish)	-	200	-
11(Coating & Surface finish)	-	200	-
Cl 8(Workmanship)	-	200	-
Cl 9(Diameter & Difference Between Two Reading On Any Two Diameters)	-	200	-
Cl 10(Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test & Decarburization Test)	-	3000	-

-
-

Bureau of Indian Standards

The National Standards Body of India

Search by IS Number