BIS - LIMS (Laboratory Information Management System)

Search by IS Number

Reset

14027 Results

S.No.

Lab Name

Osl Code

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

8731

RTRC LIMITED, GURUGRAM

9177406

IS 1180 : Part 1 (2014)

Outdoor Type Oil Immersed Distribution Transformers Upto and Including 2 500 kVA, 33kV - Specification Part 1 Mineral Oil Immersed (Fourth Revision)

Mineral Oil Immersed Distribution Transformers

120000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
21.2 a)(Measurement of winding resistance )	-	6000	Complete Testing Charges : Rs.76000/- For 0 to 100 kVA, Rs.86100/- For 100 to 250 kVA, Rs.92000- For 250 kVA to 630 kVA, Rs.93100/- For 630 kVA to 1000 kVA, Rs.117900/- For 1000 kVA to 1600 kVA. Rs.120000/- For 1600 kVA to 2500 kVA.
21.2 b)( Measurement of voltage ratio and check of phase displacemen)	-	5000	-
21.2 c)( Measurement of short-circuit impedance (principal tapping, when applicable) and load loss at 50 percent and 100 percent load)	-	5000	-
21.2 d)(Measurement of no-load loss and current)	-	3500	-
21.2 e)(Measurement of insulation resistance)	-	2000	-
21.2 f)(Induced over-voltage withstand test)	-	4500	-
21.2 g)( Separate-source voltage withstand test)	-	4000	-
21.5.1.2(Pressure test-routine test (For Transformers up to 200 kVA ))	-	4000	-
21.5.1.3(Oil leakage test upto 200 KVA)	-	3000	-
21.3(a )(Lightning impulse test)	-	38000	-
21.3(b)(Temperature-rise test)	-	23000	-
21.5.1.1(Pressure test-Type test (For Transformers up to 200 kVA ))	-	6000	-
21.4 a)( Determination of sound levels)	-	6000	-
21.4 c(No load current at 112.5 percent voltage.)	-	1000	-
21.4 d(Paint adhesion tests)	-	1500	-
21.4 e(BDV and moisture content of oil in the transformer)	-	1500	-
6.9(Permissible Flux Density and Over Fluxing )	-	6000	-
13.1(Marking (Rating Plates))	-	0	-
13.2(Terminal Marking Plate)	-	0	-
13.3(Marking )	-	0	-
13.4(Marking)	-	0	-
13.4.1(Marking)	-	0	-
14.1(MOUNTING ARRANGEMENT)	-	0	-
14.2(MOUNTING ARRANGEMENT)	-	0	-
14.3(MOUNTING ARRANGEMENT)	-	0	-
14.4(MOUNTING ARRANGEMENT)	-	0	-
15.1.1(TRANSFORMER TANK : Construction)	-	0	-
15.1.2(TRANSFORMER TANK : Construction)	-	0	-
15.1.3(TRANSFORMER TANK : Construction)	-	0	-
15.1.4(TRANSFORMER TANK : Construction)	-	0	-
15.1.5(TRANSFORMER TANK : Construction)	-	0	-
21.5.3.3(Oil leakage test)	-	0	-
21.5.2.1(Type test : For Transformers Above 200 kVA and Up to Including 2 500 kVA)	-	120000	-
21.5.2.2(routine test :For Transformers Above 200 kVA and Up to Including 2 500 kVA)	-	37000	Routine Testing Charges : Rs.19100/- For 0 to 100 kVA, Rs.22200/- For 100 to 250 kVA, Rs.24700/- For 250 kVA to 630 kVA, Rs.25600/- For 630 kVA to 1000 kVA, Rs.33100/- For 1000 kVA to 1600 kVA. Rs.37000/- For 1600 kVA to 2500 kVA.
21.5.2.3( Oil leakage test (routine test))	-	0	-
21.5.3.1(For Single Phase Distribution Transformers Up to Including 25 kVA : pressure test (type test))	-	0	-
21.5.3.2(For Single Phase Distribution Transformers Up to Including 25 kVA : pressure test (routine test))	-	0	-
21.5.3.3(Oil leakage test (routine test))	-	0	-
15.5(Total Dry Film Paint Thickness)	-	0	-
6.9, 7.9, 8.9(Permissible Flux Density and Over Fluxing)	-	0	-
11(Minimum clearance in Air)	-	0	-
16(Conservator for Non-sealed type Transformers)	-	0	-
20(Fittings)	-	0	-
6.8 (50%)(Total losses at 50 % load (Watts))	-	0	-
7.8 (50%)(Total losses at 50 % load (Watts))	-	0	-
8.8 (50%)(Total losses at 50 % load (Watts))	-	0	-
6.8 (100%)(Total losses at 100 % load (Watts))	-	0	-
7.8 (100%)(Total losses at 100 % load (Watts))	-	0	-
8.8 (100%)(Total losses at 100 % load (Watts))	-	0	-
9.1a)(CRGO Electrical Steel)	-	0	-
9.1 b)(Amorphous core material)	-	0	-
9.1 c)(Copper/Aluminium conductor)	-	0	-
9.1 d)(Kraft paper)	-	0	-
9.1 e)(Press Board)	-	0	-
9.1 f)(Mineral oil)	-	0	-
10(Terminal Arrangement)	-	0	-
15.2(Pressure and Vacuum Requirements)	-	0	-
15.4(Gasket)	-	0	-
19(Tolerances)	-	0	-
18(Efficiency and regulation)	-	0	-
4(Service Conditions)	-	0	-
5(General )	-	0	-
6.1(Rating)	-	0	-
6.2(Rated frequency)	-	0	-
6.3(Nominal system voltage)	-	0	-
6.4(Basic Insulation level )	-	0	-
6.5(No-Load Voltage Ratios)	-	0	-
6.6(Winding connections and phase displacement)	-	0	-
6.7(Tapping Range and Tapping Method)	-	0	-
6.8(Losses and impedance values)	-	0	-
6.1(Limits of Temperature-rise)	-	0	-
7(Technical Parameters of three phase distribution trasnformers higher than 200kva)	-	0	-
8(Technical Parameters of single phase distribution transformers UP to and including 25 KVA )	-	0	-
9(Standard Materials)	-	0	-
10(Terminal arrangment )	-	0	-
11(Minimum Clearnaces air )	-	0	-
12(Connectors )	-	0	-
13(Marking )	-	0	-
14(Mounting arrangement)	-	0	-
15(Trasnformer Tank )	-	0	-
16(Conservator for Non-Sealed type Transformers)	-	0	-
18(Efficiency and Regulation)	-	0	-
19(Tolerances)	-	0	-
21(General )	-	0	-
22(Information required with enquiry and order )	-	0	-
20(Fittings)	-	0	-

03 Apr, 2027

-
Exclusion: Cl.21.4 b (Short-circuit withstand test IS 2026 (Part 5) (above 200 kVA)), Cl. 17 ( ABILITY OF TRANSFORMERS TO WITHSTAND EXTERNAL SHORT CIRCUIT), Cl. 21.3(c) (Short-circuit withstand test)

8732

Bharat Test House Pvt Ltd 1474 Sonipat Haryana

9135626

IS 2215 (2006)

Starters for fluorescent lamps (Third Revision)

Starters for Fluorescent Lamps

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11(Information for Ballast Design)	-	500	5% discount for BIS
10(Deactivated Lamp Test)	-	500	5% discount for BIS
9(Endurance Test)	-	3500	5% discount for BIS
8(Starting Test)	-	1800	5% discount for BIS
7.13(Heating of Starters with operating time limitation)	-	5000	5% discount for BIS
7.12(Radio Interference Suppression Capacitors)	-	3300	5% discount for BIS
7.11(Quality of Marking)	-	200	5% discount for BIS
7.1(Resistance to Heat and Fire)	-	500	5% discount for BIS
7.9(Connections)	-	500	5% discount for BIS
7.8(Mechanical Strength)	-	500	5% discount for BIS
7.7(Torsion Test)	-	500	5% discount for BIS
7.6(Dimensions)	-	500	5% discount for BIS
7.5(Dielectric Strength)	-	500	5% discount for BIS
7.4(Insulation Resistance under Humidity Conditions)	-	2000	5% discount for BIS
7.3(Protection Against Accidental Electric Shocks)	-	100	5% discount for BIS
6(Marking)	-	100	5% discount for BIS

19 Mar, 2026

-
-

8733

RTRC LIMITED, GURUGRAM

9177406

IS 335 (2018)

New insulating oils - Specification (Fifth Revision)

New Insulating Oils

42700.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Viscosity)	-	3000.00	-
6.2(Pour Point)	-	1000.00	-
5.1(Classification)	-	0.0	-
5.2(Requirements)	-	0.0	-
5.3(Miscibility)	-	0.0	-
6.0(General)	-	0.0	-
6..3(Water Content)	-	1500.00	-
6.4(Breakdown Voltage)	-	1700.00	-
6.5(Dielectric Dissipation Factor (DDF))	-	2000.00	-
6.6(Appearance)	-	500.00	-
6.7(Acidity)	-	1000.00	-
6.8(Interfacial Tension (IFT))	-	1000.00	-
6.9(Sulphur Content)	-	2000.00	-
6.1(Corrosive Sulphur and Potentially Corrosive Sulphur)	-	1000.00	-
6.11(Additives)	-	5000.00	-
6.12(Oxidation Stability)	-	0.0	-
6.13(Gassing Tendency)	-	1500.00	-
6.15(Flash Point)	-	1000.00	-
6.16(Density)	-	1000.00	-
6.17(Polycyclic Aromatics (PCA))	-	2500.00	-
6.18(Polychlorinated Biphenyls (PCB))	-	2500.00	-
6.19(2-Furfural (2-FAL) and Related Compounds Content)	-	2500.00	-
6.2(Particle Content)	-	2000.00	-
6.21(DBDS Content)	-	2000.00	-
7.1 (a)(Total acidity)	-	1000.00	-
7.1 (b)(Sludge)	-	1000.00	-
7.1 (c)(DDF at 90°C)	-	2000.00	-
7.1 (d)(Total sulphur content)	-	0.0	-
4, 5.1.3, 6.1, Table 1(LCSET)	-	0.0	-
4, 5.1.3, 6.1, Table 1(Maximum Viscosity)	-	0.0	-
4, 5.1.3, 6.1, Table 1(Maximum Pour Point)	-	0.0	-
4, 5.2, 6, Table 2(Viscosity at 40°C)	-	0.0	-
4, 5.2, 6, Table 2(Viscosity at 0°C)	-	0.0	-
4, 5.2, 6, Table 2(Viscosity at -30°C)	-	0.0	-
4, 5.2, 6, Table 2(Viscosity at -40°C)	-	0.0	-
4, 5.2, 6, Table 2(Pour point)	-	0.0	-
4, 5.2, 6, Table 2(Water content)	-	0.0	-
4, 5.2, 6, Table 2(Breakdown voltage)	-	0.0	-
4, 5.2, 6, Table 2(DDF at 90°C)	-	0.0	-
4, 5.2, 6, Table 2(Particle content)	-	0.0	-
4, 5.2, 6, Table 2(Appearance)	-	0.0	-
4, 5.2, 6, Table 2(Acidity)	-	0.0	-
4, 5.2, 6, Table 2(Interfacial tension)	-	0.0	-
4, 5.2, 6, Table 2(Total sulphur content)	-	0.0	-
4, 5.2, 6, Table 2(Corrosive sulphur)	-	0.0	-
4, 5.2, 6, Table 2(Potentially corrosive sulphur)	-	0.0	-
4, 5.2, 6, Table 2(DBDS)	-	0.0	-
4, 5.2, 6, Table 2(Inhibitors according to IS 13631/IEC 60666)	-	0.0	-
4, 5.2, 6, Table 2(Metal passivator additives according to IS 13631/IEC 60666)	-	0.0	-
4, 5.2, 6, Table 2(Other additives)	-	0.0	-
4, 5.2, 6, Table 2(2-Furfural and related compounds content)	-	0.0	-
4, 5.2, 6, Table 2(Oxidation stability)	-	0.0	-
4, 5.2, 6, Table 2(Total acidity)	-	0.0	-
4, 5.2, 6, Table 2(Sludge)	-	0.0	-
4, 5.2, 6, Table 2(DDF at 90°C)	-	0.0	-
4, 5.2, 6, Table 2(Gassing tendency)	-	0.0	-
4, 5.2, 6, Table 2(Flash point)	-	0.0	-
4, 5.2, 6, Table 2(PCA content)	-	0.0	-
4, 5.2, 6, Table 2(PCB content)	-	0.0	-
6.22(Stray Gassing of Oil)	-	4000.00	-
7.3(Gassing Tendency)	-	0.0	-
4, 5.2, 6, Table 2(Density at 20°C)	-	0.0	-

03 Apr, 2027

-
Exclusion: Cl. 6.14 (Electrostatic Charging Tendency (ECT)), Cl. 7.2 (Electrostatic Charging Tendency (ECT)), Cl. 4, 5.2, 6, Table 2 (ECT)

8734

RTRC LIMITED, GURUGRAM

9177406

IS 191 (2007)

Copper - Specification (Fourth Revision)

9000.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1 - Table 4(Antimony-IS440)	-	500.00	-
7.1 - Table 4(Arsenic- IS440)	-	500.00	-
7.1 - Table 4(Bismuth-IS 440)	-	500.00	-
7.1 - Table 4(Copper (any Silver present to be counted as copper)-IS440)	-	500.00	-
7.1 - Table 4(Iron IS 440)	-	500.00	-
7.1 - Table 4(Lead IS 440)	-	500.00	-
7.1 - Table 4(Nickel IS 440)	-	500.00	-
7.1 - Table 4(Oxygen IS 440)	-	500.00	-
7.1 - Table 4(Phosphorus- IS 440)	-	500.00	-
7.1 - Table 4(Silver- IS 440)	-	500.00	-
7.1 - Table 4(Sulphur- IS 440)	-	500.00	-
7.1 - Table 4(Tin - IS 440)	-	500.00	-
7.1 - Table 4(Tellurium- IS 440)	-	500.00	-
7.1 - Table 4(Selenium - IS 440)	-	500.00	-
7.1 - Table 4(Znic-IS 440)	-	500.00	-
4-Table 1(GRADES/DESIGNATIONS)	-	0.0	-
7.1 - Table 4(Copper + Silver(By difference)-IS440)	-	0.0	-
5.1- Table 2(L)	-	0.0	-
5.1- Table 2(L1)	-	0.0	-
5.1- Table 2(h)	-	0.0	-
5.1- Table 2(h1)	-	0.0	-
5.1- Table 2(b)	-	0.0	-
5.1- Table 2(b1)	-	0.0	-
5.1- Table 2(R)	-	0.0	-
5.1- Table 2(R1)	-	0.0	-
5.1- Table 2(R2 )	-	0.0	-
5.1- Table 2(α )	-	0.0	-
5.1- Table 2( β )	-	0.0	-
5.1- Table 2(γ)	-	0.0	-
7.1 - Table 4(Selenium + Telluuium- IS 440)	-	0.0	-
7.1 - Table 4(Total Impurities- IS 440)	-	0.0	-
5.2(Billets)	-	0.0	-
5.4-Table 3 (For Billets)(Mass)	-	0.0	-
5.2-Table 3 (For Billets)(Diameter)	-	0.0	-
5.2-Table 3 (For Billets)(Length)	-	0.0	-
5.2-Table 3 (For Billets)(Deviation from straightness per 1000 mm length)	-	0.0	-
5.4-Table 3 (Vertically continuously cast wire bars)(Mass)	-	0.0	-
5.3-Table 3 (Vertically continuously cast wire bars)(Width)	-	0.0	-
5.3-Table 3 (Vertically continuously cast wire bars)(thickness )	-	0.0	-
5.3-Table 3 (Vertically continuously cast wire bars)(Other dimention)	-	0.0	-
5.4-Table 3 (Vertically static cast wire bars)(Mass)	-	0.0	-
5.3-Table 3 (Vertically static cast wire bars)(Width)	-	0.0	-
5.3-Table 3 (Vertically static cast wire bars)(thickness )	-	0.0	-
5.3-Table 3 (Vertically static cast wire bars)(Other dimention)	-	0.0	-
5.4-Table 3 (Ingots)(Mass)	-	0.0	-
5.4-Table 3 (Cast cakes)(Mass)	-	0.0	-
5.3-Table 3 (Cast cakes)(Width)	-	0.0	-
5.3-Table 3 (Cast cakes)(thickness )	-	0.0	-
5.3-Table 3 (Cast cakes)(Deviation from straightness per 1000 mm length)	-	0.0	-
8.1(FREEDOM FROM DEFECTS)	-	0.0	-
8.2(FREEDOM FROM DEFECTS)	-	0.0	-
9.1- Table 5(Mass Resistivity- IS 3635)	-	0.0	-
10(HYDROGEN EMBRITTLEMENT TEST- IS 191)	-	1000.00	-
4-Table 1(GRADES/DESIGNATIONS)	-	0.0	-
5.1- Table 2(L)	-	0.0	-
5.1- Table 2(L1)	-	0.0	-
5.1- Table 2(h)	-	0.0	-
5.1- Table 2(h1)	-	0.0	-
5.1- Table 2(b)	-	0.0	-
5.1- Table 2(b1)	-	0.0	-
5.1- Table 2(R)	-	0.0	-
5.1- Table 2(R1)	-	0.0	-
5.1- Table 2(R2 )	-	0.0	-
5.1- Table 2(α )	-	0.0	-
5.1- Table 2( β )	-	0.0	-
5.1- Table 2(γ)	-	0.0	-
5.2(Billets)	-	0.0	-
5.4-Table 3 (For Billets)(Mass)	-	0.0	-
5.2-Table 3 (For Billets)(Diameter)	-	0.0	-
5.2-Table 3 (For Billets)(Length)	-	0.0	-
5.2-Table 3 (For Billets)(Deviation from straightness per 1000 mm length)	-	0.0	-
5.4-Table 3 (Vertically continuously cast wire bars)(Mass)	-	0.0	-
5.3-Table 3 (Vertically continuously cast wire bars)(Width)	-	0.0	-
5.3-Table 3 (Vertically continuously cast wire bars)(thickness )	-	0.0	-
5.3-Table 3 (Vertically continuously cast wire bars)(Other dimention)	-	0.0	-
5.4-Table 3 (Vertically static cast wire bars)(Mass)	-	0.0	-
5.3-Table 3 (Vertically static cast wire bars)(Width)	-	0.0	-
5.3-Table 3 (Vertically static cast wire bars)(thickness )	-	0.0	-
5.3-Table 3 (Vertically static cast wire bars)(Other dimention)	-	0.0	-
5.4-Table 3 (Ingots)(Mass)	-	0.0	-
5.4-Table 3 (Cast cakes)(Mass)	-	0.0	-
5.3-Table 3 (Cast cakes)(Width)	-	0.0	-
5.3-Table 3 (Cast cakes)(thickness )	-	0.0	-
5.3-Table 3 (Cast cakes)(Deviation from straightness per 1000 mm length)	-	0.0	-
7.1 - Table 4(Copper + Silver(By difference)-IS440)	-	0.0	-
7.1 - Table 4(Silver- IS 440)	-	0.0	-
7.1 - Table 4(Copper (any Silver present to be counted as copper)-IS440)	-	0.0	-
7.1 - Table 4(Phosphorus- IS 440)	-	0.0	-
7.1 - Table 4(Arsenic- IS440)	-	0.0	-
7.1 - Table 4(Antimony-IS440)	-	0.0	-
7.1 - Table 4(Bismuth-IS 440)	-	0.0	-
7.1 - Table 4(Iron IS 440)	-	0.0	-
7.1 - Table 4(Lead IS 440)	-	0.0	-
7.1 - Table 4(Nickel IS 440)	-	0.0	-
7.1 - Table 4(Oxygen IS 440)	-	0.0	-
7.1 - Table 4(Selenium - IS 440)	-	0.0	-
7.1 - Table 4(Sulphur- IS 440)	-	0.0	-
7.1 - Table 4(Tellurium- IS 440)	-	0.0	-
7.1 - Table 4(Tin - IS 440)	-	0.0	-
7.1 - Table 4(Znic-IS 440)	-	0.0	-
7.1 - Table 4(Selenium + Telluuium- IS 440)	-	0.0	-
7.1 - Table 4(Total Impurities- IS 440)	-	0.0	-
8.1(FREEDOM FROM DEFECTS)	-	0.0	-
8.2(FREEDOM FROM DEFECTS)	-	0.0	-
9.1- Table 5(Mass Resistivity- IS 3635)	-	0.0	-
10(HYDROGEN EMBRITTLEMENT TEST- IS 191)	-	0.0	-
9.1 , 9.2 & 10(Resistivity & HYDROGEN EMBRITTLEMENT TEST)	-	500.00	-
9.1 , 9.2 & 10(Resistivity & HYDROGEN EMBRITTLEMENT TEST)	-	0.0	-
13(Marking)	-	0.0	-
13(Marking)	-	0.0	-
13(Marking)	-	0.0	-

03 Apr, 2027

-
-

8735

Sleen India Biz venture Private Limited, Agra

9139736

IS 17043 : Part 2 (2024)

Shoes: Shoes for General Purpose

Shoes for General Purpose

58400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.1(Shape and Design)	-	100	10% Discount on BIS Sample.
Cl-5.3(Material)	-	100	10% Discount on BIS Sample.
Cl-5.4, Table-1 (i)(Bond strength, N/mm, Min Upper to outsole, N/mm, Min)	-	600	10% Discount on BIS Sample.
Cl-5.4, Table-1 (ii)(Inter layer bond strength,= N/mm, Min Midsole to outsole, N/mm, Min)	-	600	10% Discount on BIS Sample.
Cl-5.4, Table-1 (iii)(Whole shoe flexing, flexes)	-	1000	10% Discount on BIS Sample.
Cl-5.4, Table-1 (iv)(Water proofness on complete shoe)	-	1000	10% Discount on BIS Sample.
Cl-5.4, Table-1 (v)(Slip resistance, Cof(1), Min dry and wet* (quarry tile))	-	1800	10% Discount on BIS Sample.
Cl-5.4, Table-1 (vi)(Attachment strength of strap and buckle/D-ring N)	-	500	10% Discount on BIS Sample.
Cl-5.4, Table-1 (vii)(Attachment strength of strap and velcro , N, Min)	-	500	10% Discount on BIS Sample.
Cl-5.4, Table-1 (viii)(Strength of eyelet attachment, N, Min)	-	500	10% Discount on BIS Sample.
Cl-5.4, Table-1 (ix)(Heel pull off strength, N, Min)	-	700	10% Discount on BIS Sample.
Cl-5.4, Table-1 (x)(Top piece attachment strength, N, Min)	-	500	10% Discount on BIS Sample.
Cl-5.4, Table-1 (xi)(Seam strength, N/mm, Min)	-	600	10% Discount on BIS Sample.
Cl-5.4, Table-1 (xii)(Whole shoe topline strength, N, Min)	-	500	10% Discount on BIS Sample.
Cl-5.4, Table-1 (xiii)(Abrasion resistance (volume loss), mm3)	-	850	10% Discount on BIS Sample.
Cl-5.4, Table-1 (xiv)(Chemical requirements(3))	-	30000	10% Discount on BIS Sample.
Cl-5.4, Table-1 (xv)(Lead content (as Pb) ppm, Max)	-	500	10% Discount on BIS Sample.
Cl-5.4, Table-1 (xvi)(Hydrolysis resistance,(4) cut growth at 150 000 flexes, mm, Max)	-	1800	10% Discount on BIS Sample.
Cl-6.1.1, Table-2 (i)(Tear trength, N)	-	600	10% Discount on BIS Sample.
Cl-6.1.1, Table-2 (ii)(Flexing resistance, flexes)	-	800	10% Discount on BIS Sample.
Cl-6.1.1, Table-2 (iii)(Colour fastness to rubbing (marring/staining))	-	500	10% Discount on BIS Sample.
Cl-6.1.1, Table-2 (iv)(Colour fastness to water (contact method- multi fabrics))	-	400	10% Discount on BIS Sample.
Cl-6.1.1, Table-2 (v)(Water vapour permeability,mg/cm2 /h, Min Water vapour coefficient,mg/cm2 , Min)	-	800	10% Discount on BIS Sample.
Cl-6.1.1, Table-2 (vi)(Stitch tear strength, N/mm, Min)	-	500	10% Discount on BIS Sample.
Cl-6.1.1, Table-2 (vii)(Abrasion resistance)	-	1000	10% Discount on BIS Sample.
Cl-6.1.2, Table-3 (i)(Colour fastness to light, Marring, Min)	-	700	10% Discount on BIS Sample.
Cl-6.1.2, Table-3 (ii)(Water resistance)	-	800	10% Discount on BIS Sample.
Cl-6.1.2, Table-3 (iii)(Flexing resistance, flexes at (-) 5 °C 25 000 flexes)	-	1200	10% Discount on BIS Sample.
Cl-6.1.3, Table- 4 (i)(Breaking strength, N/mm, Min Elongation at break, percent, Min)	-	600	10% Discount on BIS Sample.
Cl-6.1.3, Table- 4 (ii)(Tear Strength, N, Min)	-	600	10% Discount on BIS Sample.
Cl-6.1.3, Table- 4 (iii)(Strength at needle perforation, N/mm, Min)	-	600	10% Discount on BIS Sample.
Cl-6.1.3, Table- 4 (iv)(Flexing resistance, Flexes)	-	800	10% Discount on BIS Sample.
Cl-6.1.3, Table- 4 (v)(Water vapour permeability (WVP), mg/cm2 /h, Min)	-	800	10% Discount on BIS Sample.
Cl-6.1.3, Table- 4 (vi)(Hydrolysis resistance)	-	1800	10% Discount on BIS Sample.
Cl-6.1.3, Table- 4 (vii)(Abrasion resistance)	-	1000	10% Discount on BIS Sample.
Cl-6.1.4, Table-5 (i)(Colour fastness to light, Marring, Min)	-	800	10% Discount on BIS Sample.
Cl-6.1.4, Table- 5 (ii)(Flexing resistance, flexes at (-) 5 ºC, s 25 000 flexes)	-	1200	10% Discount on BIS Sample.
Cl-6.2, Table-6 (i)(Tear strength, N, Min)	-	600	10% Discount on BIS Sample.
Cl-6.2, Table-6 (ii)(Abrasion resistance)	-	1000	10% Discount on BIS Sample.
Cl-6.2, Table-6 (iii)(Colour fastness rubbing (crocking))	-	300	10% Discount on BIS Sample.
Cl-6.2, Table-6 (iv)(Colour fastness to perspiration)	-	400	10% Discount on BIS Sample.
Cl-6.2, Table-6 (v)(Water vapour permeability, mg/cm2 /h, Min Water vapour coefficient, mg/cm2, Min)	-	800	10% Discount on BIS Sample.
Cl-6.3, Table-7 (i)(Flexing index, Min)	-	800	10% Discount on BIS Sample.
Cl-6.3, Table-7 (ii)(Abrasion resistance at 400 cycles)	-	300	10% Discount on BIS Sample.
Cl-6.3, Table-7 (iii)(Water absorption, mg/cm2 , Min Water desorption, percent, Min)	-	800	10% Discount on BIS Sample.
Cl-6.4, Table-8 (i)(Thickness, mm, Min)	-	100	10% Discount on BIS Sample.
Cl-6.4, Table-8 (ii)(Abrasion resistance)	-	1000	10% Discount on BIS Sample.
Cl-6.4, Table-8 (iii)(Water absorption, mg/cm2 , Min Water desorption, percent, Min)	-	800	10% Discount on BIS Sample.
Cl-6.5.1, , Table-9 (i)(Flexing resistance)	-	800	10% Discount on BIS Sample.
Cl-6.5.1, , Table-9 (ii)(Hydrolysis resistance, cut growth at 150 000 flexes, mm, Max)	-	1800	10% Discount on BIS Sample.
Cl-6.5.1, , Table-9 (iii)(Compression set, percent, Max)	-	500	10% Discount on BIS Sample.
Cl-6.5.2.1, Table-10 (i)(Grain crack index, Min)	-	500	10% Discount on BIS Sample.
Cl-6.5.2.1, Table-10 (ii)(Density, g/cm3 , Min)	-	200	10% Discount on BIS Sample.
Cl-6.5.2.1, Table-10 (iii)(Abrasion resistance, mm/kcs, Max)	-	800	10% Discount on BIS Sample.
Cl-6.5.2.2, Table-11 (i)(Water resistance, (dynamic method))	-	1000	10% Discount on BIS Sample.
Cl-6.5.2.3, Table-12 (i)(Hardness, Min)	-	200	10% Discount on BIS Sample.
Cl-6.5.2.3, Table-12 (ii)(Density, g/cm3 , Max)	-	200	10% Discount on BIS Sample.
Cl-6.5.2.3, Table-12 (iii)(Abrasion resistance (volume loss), mm3 , Max)	-	850	10% Discount on BIS Sample.
Cl-6.5.2.3, Table-12 (iv)(Bond Strength between Rubber top-lift and adjacent material, N/mm, Min)	-	600	10% Discount on BIS Sample.
Cl-6.6, Table-13 (i)(Heat shrinkage, percent, Max)	-	300	10% Discount on BIS Sample.
Cl-6.6, Table-13 (ii)(Split tear strength, kg/25 mm, Min)	-	600	10% Discount on BIS Sample.
Cl-6.6, Table-13 (iii)(Compression set, percent, Max)	-	500	10% Discount on BIS Sample.
Cl-6.7, Table-14 (i)(Hardness, N)	-	300	10% Discount on BIS Sample.
Cl-6.7, Table-14 (ii)(Resilience, percent)	-	300	10% Discount on BIS Sample.
Cl-6.7, Table-14 (iii)(Moisture resistance, percent)	-	300	10% Discount on BIS Sample.
Cl-6.10, Table-17 (i)(Lace breaking strength, N, Min)	-	500	10% Discount on BIS Sample.
Cl-6.10, Table-17 (ii)(Lace tag strength, N, Min)	-	500	10% Discount on BIS Sample.
Cl-6.10, Table-17 (iii)(Lace to lace abrasion resistance, cycles)	-	500	10% Discount on BIS Sample.
Cl-6.10, Table-17 (iv)(Colour fastness to water for lace contact methodstaining Gray scale rate , Min)	-	300	10% Discount on BIS Sample.
Cl-6.10, Table-17 (v)(Corrosion resistance)	-	300	10% Discount on BIS Sample.
Cl-6.11, Table-18 (i)(Fatigue resistance, cycles, Min)	-	700	10% Discount on BIS Sample.
Cl-6.11, Table-18 (ii)(Security of puller attachment strength, N, Min)	-	300	10% Discount on BIS Sample.
Cl-6.11, Table-18 (iii)(Lateral load, N, Min)	-	300	10% Discount on BIS Sample.
Cl-6.11, Table-18 (iv)(End attachment strength, N, Min)	-	300	10% Discount on BIS Sample.
Cl-8.1(Marking)	-	0	-
Cl-5.1(Shape and Design)	-	300	10% Discount on BIS Sample.
Cl-5.3(Material)	-	100	10% Discount on BIS Sample.
Cl-5.4, Table-1 (i)(Bond strength, N/mm, Min Upper to outsole, N/mm, Min)	-	600	10% Discount on BIS Sample.
Cl-5.4, Table-1 (ii)(Inter layer bond strength,= N/mm, Min Midsole to outsole, N/mm, Min)	-	600	10% Discount on BIS Sample.
Cl-5.4, Table-1 (iii)(Whole shoe flexing, flexes)	-	1000	10% Discount on BIS Sample.
Cl-5.4, Table-1 (iv)(Water proofness on complete shoe)	-	1200	10% Discount on BIS Sample.
Cl-5.4, Table-1 (v)(Slip resistance, Cof(1), Min dry and wet* (quarry tile))	-	3000	10% Discount on BIS Sample.
Cl-5.4, Table-1 (vi)(Attachment strength of strap and buckle/D-ring N)	-	500	10% Discount on BIS Sample.
Cl-5.4, Table-1 (vii)(Attachment strength of strap and velcro , N, Min)	-	500	10% Discount on BIS Sample.
Cl-5.4, Table-1 (viii)(Strength of eyelet attachment, N, Min)	-	500	10% Discount on BIS Sample.
Cl-5.4, Table-1 (ix)(Heel pull off strength, N, Min)	-	700	10% Discount on BIS Sample.
Cl-5.4, Table-1 (x)(Top piece attachment strength, N, Min)	-	500	10% Discount on BIS Sample.
Cl-5.4, Table-1 (xi)(Seam strength, N/mm, Min)	-	600	10% Discount on BIS Sample.
Cl-5.4, Table-1 (xii)(Whole shoe topline strength, N, Min)	-	500	10% Discount on BIS Sample.
Cl-5.4, Table-1 (xiii)(Abrasion resistance (volume loss), mm3)	-	1000	10% Discount on BIS Sample.
Cl-5.4, Table-1 (xiv)(Chemical requirements(3))	-	30000	10% Discount on BIS Sample.
Cl-5.4, Table-1 (xv)(Lead content (as Pb) ppm, Max)	-	1000	10% Discount on BIS Sample.
Cl-5.4, Table-1 (xvi)(Hydrolysis resistance,(4) cut growth at 150 000 flexes, mm, Max)	-	3000	10% Discount on BIS Sample.
Cl-6.1.1, Table-2 (i)(Tear trength, N)	-	600	10% Discount on BIS Sample.
Cl-6.1.1, Table-2 (ii)(Flexing resistance, flexes)	-	1000	10% Discount on BIS Sample.
Cl-6.1.1, Table-2 (iii)(Colour fastness to rubbing (marring/staining))	-	500	10% Discount on BIS Sample.
Cl-6.1.1, Table-2 (iv)(Colour fastness to water (contact method- multi fabrics))	-	400	10% Discount on BIS Sample.
Cl-6.1.1, Table-2 (v)(Water vapour permeability,mg/cm2 /h, Min Water vapour coefficient,mg/cm2 , Min)	-	1000	10% Discount on BIS Sample.
Cl-6.1.1, Table-2 (vi)(Stitch tear strength, N/mm, Min)	-	600	10% Discount on BIS Sample.
Cl-6.1.1, Table-2 (vii)(Abrasion resistance)	-	1000	10% Discount on BIS Sample.
Cl-6.1.2, Table-3 (i)(Colour fastness to light, Marring, Min)	-	1000	10% Discount on BIS Sample.
Cl-6.1.2, Table-3 (ii)(Water resistance)	-	1200	10% Discount on BIS Sample.
Cl-6.1.2, Table-3 (iii)(Flexing resistance, flexes at (-) 5 °C 25 000 flexes)	-	1500	10% Discount on BIS Sample.
Cl-6.1.3, Table- 4 (i)(Breaking strength, N/mm, Min Elongation at break, percent, Min)	-	700	10% Discount on BIS Sample.
Cl-6.1.3, Table- 4 (ii)(Tear Strength, N, Min)	-	600	10% Discount on BIS Sample.
Cl-6.1.3, Table- 4 (iii)(Strength at needle perforation, N/mm, Min)	-	600	10% Discount on BIS Sample.
Cl-6.1.3, Table- 4 (iv)(Flexing resistance, Flexes)	-	1000	10% Discount on BIS Sample.
Cl-6.1.3, Table- 4 (v)(Water vapour permeability (WVP), mg/cm2 /h, Min)	-	1000	10% Discount on BIS Sample.
Cl-6.1.3, Table- 4 (vi)(Hydrolysis resistance)	-	3000	10% Discount on BIS Sample.
Cl-6.1.3, Table- 4 (vii)(Abrasion resistance)	-	1000	10% Discount on BIS Sample.
Cl-6.1.4, Table-5 (i)(Colour fastness to light, Marring, Min)	-	1000	10% Discount on BIS Sample.
Cl-6.1.4, Table- 5 (ii)(Flexing resistance, flexes at (-) 5 ºC, s 25 000 flexes)	-	1500	10% Discount on BIS Sample.
Cl-6.2, Table-6 (i)(Tear strength, N, Min)	-	600	10% Discount on BIS Sample.
Cl-6.2, Table-6 (ii)(Abrasion resistance)	-	1000	10% Discount on BIS Sample.
Cl-6.2, Table-6 (iii)(Colour fastness rubbing (crocking))	-	500	10% Discount on BIS Sample.
Cl-6.2, Table-6 (iv)(Colour fastness to perspiration)	-	500	10% Discount on BIS Sample.
Cl-6.2, Table-6 (v)(Water vapour permeability, mg/cm2 /h, Min Water vapour coefficient, mg/cm2, Min)	-	1000	10% Discount on BIS Sample.
Cl-6.3, Table-7 (i)(Flexing index, Min)	-	1000	10% Discount on BIS Sample.
Cl-6.3, Table-7 (ii)(Abrasion resistance at 400 cycles)	-	500	10% Discount on BIS Sample.
Cl-6.3, Table-7 (iii)(Water absorption, mg/cm2 , Min Water desorption, percent, Min)	-	1000	10% Discount on BIS Sample.
Cl-6.4, Table-8 (i)(Thickness, mm, Min)	-	200	10% Discount on BIS Sample.
Cl-6.4, Table-8 (ii)(Abrasion resistance)	-	1000	10% Discount on BIS Sample.
Cl-6.4, Table-8 (iii)(Water absorption, mg/cm2 , Min Water desorption, percent, Min)	-	1000	10% Discount on BIS Sample.
Cl-6.5.1, , Table-9 (i)(Flexing resistance)	-	1000	10% Discount on BIS Sample.
Cl-6.5.1, , Table-9 (ii)(Hydrolysis resistance, cut growth at 150 000 flexes, mm, Max)	-	3000	10% Discount on BIS Sample.
Cl-6.5.1, , Table-9 (iii)(Compression set, percent, Max)	-	800	10% Discount on BIS Sample.
Cl-6.5.2.1, Table-10 (i)(Grain crack index, Min)	-	500	10% Discount on BIS Sample.
Cl-6.5.2.1, Table-10 (ii)(Density, g/cm3 , Min)	-	300	10% Discount on BIS Sample.
Cl-6.5.2.1, Table-10 (iii)(Abrasion resistance, mm/kcs, Max)	-	1000	10% Discount on BIS Sample.
Cl-6.5.2.2, Table-11 (i)(Water resistance, (dynamic method))	-	1200	10% Discount on BIS Sample.
Cl-6.5.2.3, Table-12 (i)(Hardness, Min)	-	500	10% Discount on BIS Sample.
Cl-6.5.2.3, Table-12 (ii)(Density, g/cm3 , Max)	-	300	10% Discount on BIS Sample.
Cl-6.5.2.3, Table-12 (iii)(Abrasion resistance (volume loss), mm3 , Max)	-	1000	10% Discount on BIS Sample.
Cl-6.5.2.3, Table-12 (iv)(Bond Strength between Rubber top-lift and adjacent material, N/mm, Min)	-	600	10% Discount on BIS Sample.
Cl-6.6, Table-13 (i)(Heat shrinkage, percent, Max)	-	700	10% Discount on BIS Sample.
Cl-6.6, Table-13 (ii)(Split tear strength, kg/25 mm, Min)	-	600	10% Discount on BIS Sample.
Cl-6.6, Table-13 (iii)(Compression set, percent, Max)	-	800	10% Discount on BIS Sample.
Cl-6.7, Table-14 (i)(Hardness, N)	-	500	10% Discount on BIS Sample.
Cl-6.7, Table-14 (ii)(Resilience, percent)	-	400	10% Discount on BIS Sample.
Cl-6.7, Table-14 (iii)(Moisture resistance, percent)	-	400	10% Discount on BIS Sample.
Cl-6.10, Table-17 (i)(Lace breaking strength, N, Min)	-	500	10% Discount on BIS Sample.
Cl-6.10, Table-17 (ii)(Lace tag strength, N, Min)	-	500	10% Discount on BIS Sample.
Cl-6.10, Table-17 (iii)(Lace to lace abrasion resistance, cycles)	-	600	10% Discount on BIS Sample.
Cl-6.10, Table-17 (iv)(Colour fastness to water for lace contact methodstaining Gray scale rate , Min)	-	400	10% Discount on BIS Sample.
Cl-6.10, Table-17 (v)(Corrosion resistance)	-	500	10% Discount on BIS Sample.
Cl-6.11, Table-18 (i)(Fatigue resistance, cycles, Min)	-	700	10% Discount on BIS Sample.
Cl-6.11, Table-18 (ii)(Security of puller attachment strength, N, Min)	-	500	10% Discount on BIS Sample.
Cl-6.11, Table-18 (iii)(Lateral load, N, Min)	-	500	10% Discount on BIS Sample.
Cl-6.11, Table-18 (iv)(End attachment strength, N, Min)	-	500	10% Discount on BIS Sample.
Cl-8.1(Marking)	-	100	10% Discount on BIS Sample.
Cl-6.7, Table-14 (iv)(Area shape retention, percent (a) Initial, Min b) After 10 collapsing load, Min)	-	400	10% Discount on BIS Sample.
Cl-6.7, Table-14 (v)(Adhesion strength, N/mm)	-	500	10% Discount on BIS Sample.
Cl-6.8, Table-15 (i)(Peel strength, N/mm a) Initial, Min b) After 5 000 wear cycles, Min)	-	1000	10% Discount on BIS Sample.
Cl- 6.8, Table-15 (ii)(a) Shear strength, kPa b) Initial, Min)	-	1000	10% Discount on BIS Sample.
Cl- 6.9, Table-16 (i)(Limit of useful extension, percent, Min)	-	500	10% Discount on BIS Sample.
Cl- 6.9, Table-16 (ii)(Needle strength, N/mm, Min)	-	500	10% Discount on BIS Sample.
Cl-5.1(Shape and Design)	-	0	-
Cl-5.3(Material)	-	0	-
Cl-5.4, Table-1 (i)(Bond strength, N/mm, Min Upper to outsole, N/mm, Min)	-	0	-
Cl-5.4, Table-1 (ii)(Inter layer bond strength,= N/mm, Min Midsole to outsole, N/mm, Min)	-	0	-
Cl-5.4, Table-1 (iii)(Whole shoe flexing, flexes)	-	0	-
Cl-5.4, Table-1 (iv)(Water proofness on complete shoe)	-	0	-
Cl-5.4, Table-1 (v)(Slip resistance, Cof(1), Min dry and wet* (quarry tile))	-	0	-
Cl-5.4, Table-1 (vi)(Attachment strength of strap and buckle/D-ring N)	-	0	-
Cl-5.4, Table-1 (vii)(Attachment strength of strap and velcro , N, Min)	-	0	-
Cl-5.4, Table-1 (viii)(Strength of eyelet attachment, N, Min)	-	0	-
Cl-5.4, Table-1 (ix)(Heel pull off strength, N, Min)	-	0	-
Cl-5.4, Table-1 (x)(Top piece attachment strength, N, Min)	-	0	-
Cl-5.4, Table-1 (xi)(Seam strength, N/mm, Min)	-	0	-
Cl-5.4, Table-1 (xii)(Whole shoe topline strength, N, Min)	-	0	-
Cl-5.4, Table-1 (xiii)(Abrasion resistance (volume loss), mm3)	-	0	-
Cl-5.4, Table-1 (xiv)(Chemical requirements(3))	-	0	-
Cl-5.4, Table-1 (xv)(Lead content (as Pb) ppm, Max)	-	0	-
Cl-5.4, Table-1 (xvi)(Hydrolysis resistance,(4) cut growth at 150 000 flexes, mm, Max)	-	0	-
Cl-6.1.1, Table-2 (i)(Tear trength, N)	-	0	-
Cl-6.1.1, Table-2 (ii)(Flexing resistance, flexes)	-	0	-
Cl-6.1.1, Table-2 (iii)(Colour fastness to rubbing (marring/staining))	-	0	-
Cl-6.1.1, Table-2 (iv)(Colour fastness to water (contact method- multi fabrics))	-	0	-
Cl-6.1.1, Table-2 (v)(Water vapour permeability,mg/cm2 /h, Min Water vapour coefficient,mg/cm2 , Min)	-	0	-
Cl-6.1.1, Table-2 (vi)(Stitch tear strength, N/mm, Min)	-	0	-
Cl-6.1.1, Table-2 (vii)(Abrasion resistance)	-	0	-
Cl-6.1.2, Table-3 (i)(Colour fastness to light, Marring, Min)	-	0	-
Cl-6.1.2, Table-3 (ii)(Water resistance)	-	0	-
Cl-6.1.2, Table-3 (iii)(Flexing resistance, flexes at (-) 5 °C 25 000 flexes)	-	0	-
Cl-6.1.3, Table- 4 (i)(Breaking strength, N/mm, Min Elongation at break, percent, Min)	-	0	-
Cl-6.1.3, Table- 4 (ii)(Tear Strength, N, Min)	-	0	-
Cl-6.1.3, Table- 4 (iii)(Strength at needle perforation, N/mm, Min)	-	0	-
Cl-6.1.3, Table- 4 (iv)(Flexing resistance, Flexes)	-	0	-
Cl-6.1.3, Table- 4 (v)(Water vapour permeability (WVP), mg/cm2 /h, Min)	-	0	-
Cl-6.1.3, Table- 4 (vi)(Hydrolysis resistance)	-	0	-
Cl-6.1.3, Table- 4 (vii)(Abrasion resistance)	-	0	-
Cl-6.1.4, Table-5 (i)(Colour fastness to light, Marring, Min)	-	0	-
Cl-6.1.4, Table- 5 (ii)(Flexing resistance, flexes at (-) 5 ºC, s 25 000 flexes)	-	0	-
Cl-6.2, Table-6 (i)(Tear strength, N, Min)	-	0	-
Cl-6.2, Table-6 (ii)(Abrasion resistance)	-	0	-
Cl-6.2, Table-6 (iii)(Colour fastness rubbing (crocking))	-	0	-
Cl-6.2, Table-6 (iv)(Colour fastness to perspiration)	-	0	-
Cl-6.2, Table-6 (v)(Water vapour permeability, mg/cm2 /h, Min Water vapour coefficient, mg/cm2, Min)	-	0	-
Cl-6.3, Table-7 (i)(Flexing index, Min)	-	0	-
Cl-6.3, Table-7 (ii)(Abrasion resistance at 400 cycles)	-	0	-
Cl-6.3, Table-7 (iii)(Water absorption, mg/cm2 , Min Water desorption, percent, Min)	-	0	-
Cl-6.4, Table-8 (i)(Thickness, mm, Min)	-	0	-
Cl-6.4, Table-8 (ii)(Abrasion resistance)	-	0	-
Cl-6.4, Table-8 (iii)(Water absorption, mg/cm2 , Min Water desorption, percent, Min)	-	0	-
Cl-6.5.1, , Table-9 (i)(Flexing resistance)	-	0	-
Cl-6.5.1, , Table-9 (ii)(Hydrolysis resistance, cut growth at 150 000 flexes, mm, Max)	-	0	-
Cl-6.5.1, , Table-9 (iii)(Compression set, percent, Max)	-	0	-
Cl-6.5.2.1, Table-10 (i)(Grain crack index, Min)	-	0	-
Cl-6.5.2.1, Table-10 (ii)(Density, g/cm3 , Min)	-	0	-
Cl-6.5.2.1, Table-10 (iii)(Abrasion resistance, mm/kcs, Max)	-	0	-
Cl-6.5.2.2, Table-11 (i)(Water resistance, (dynamic method))	-	0	-
Cl-6.5.2.3, Table-12 (i)(Hardness, Min)	-	0	-
Cl-6.5.2.3, Table-12 (ii)(Density, g/cm3 , Max)	-	0	-
Cl-6.5.2.3, Table-12 (iii)(Abrasion resistance (volume loss), mm3 , Max)	-	0	-
Cl-6.5.2.3, Table-12 (iv)(Bond Strength between Rubber top-lift and adjacent material, N/mm, Min)	-	0	-
Cl-6.6, Table-13 (i)(Heat shrinkage, percent, Max)	-	0	-
Cl-6.6, Table-13 (ii)(Split tear strength, kg/25 mm, Min)	-	0	-
Cl-6.6, Table-13 (iii)(Compression set, percent, Max)	-	0	-
Cl-6.7, Table-14 (i)(Hardness, N)	-	0	-
Cl-6.7, Table-14 (ii)(Resilience, percent)	-	0	-
Cl-6.7, Table-14 (iii)(Moisture resistance, percent)	-	0	-
Cl-6.10, Table-17 (i)(Lace breaking strength, N, Min)	-	0	-
Cl-6.10, Table-17 (ii)(Lace tag strength, N, Min)	-	0	-
Cl-6.10, Table-17 (iii)(Lace to lace abrasion resistance, cycles)	-	0	-
Cl-6.10, Table-17 (iv)(Colour fastness to water for lace contact methodstaining Gray scale rate , Min)	-	0	-
Cl-6.10, Table-17 (v)(Corrosion resistance)	-	0	-
Cl-6.11, Table-18 (i)(Fatigue resistance, cycles, Min)	-	0	-
Cl-6.11, Table-18 (ii)(Security of puller attachment strength, N, Min)	-	0	-
Cl-6.11, Table-18 (iii)(Lateral load, N, Min)	-	0	-
Cl-6.11, Table-18 (iv)(End attachment strength, N, Min)	-	0	-
Cl-8.1(Marking)	-	0	-
Cl-6.7, Table-14 (iv)(Area shape retention, percent (a) Initial, Min b) After 10 collapsing load, Min)	-	0	-
Cl-6.7, Table-14 (v)(Adhesion strength, N/mm)	-	0	-
Cl-6.8, Table-15 (i)(Peel strength, N/mm a) Initial, Min b) After 5 000 wear cycles, Min)	-	0	-
Cl- 6.8, Table-15 (ii)(a) Shear strength, kPa b) Initial, Min)	-	0	-
Cl- 6.9, Table-16 (i)(Limit of useful extension, percent, Min)	-	0	-
Cl- 6.9, Table-16 (ii)(Needle strength, N/mm, Min)	-	0	-
Cl-5.1(Shape and Design)	-	0	-
Cl-5.3(Material)	-	0	-
Cl-5.4, Table-1 (i)(Bond strength, N/mm, Min Upper to outsole, N/mm, Min)	-	0	-
Cl-5.4, Table-1 (ii)(Inter layer bond strength,= N/mm, Min Midsole to outsole, N/mm, Min)	-	0	-
Cl-5.4, Table-1 (iii)(Whole shoe flexing, flexes)	-	0	-
Cl-5.4, Table-1 (iv)(Water proofness on complete shoe)	-	0	-
Cl-5.4, Table-1 (v)(Slip resistance, Cof(1), Min dry and wet* (quarry tile))	-	0	-
Cl-5.4, Table-1 (vi)(Attachment strength of strap and buckle/D-ring N)	-	0	-
Cl-5.4, Table-1 (vii)(Attachment strength of strap and velcro , N, Min)	-	0	-
Cl-5.4, Table-1 (viii)(Strength of eyelet attachment, N, Min)	-	0	-
Cl-5.4, Table-1 (ix)(Heel pull off strength, N, Min)	-	0	-
Cl-5.4, Table-1 (x)(Top piece attachment strength, N, Min)	-	0	-
Cl-5.4, Table-1 (xi)(Seam strength, N/mm, Min)	-	0	-
Cl-5.4, Table-1 (xii)(Whole shoe topline strength, N, Min)	-	0	-
Cl-5.4, Table-1 (xiii)(Abrasion resistance (volume loss), mm3)	-	0	-
Cl-5.4, Table-1 (xiv)(Chemical requirements(3))	-	0	-
Cl-5.4, Table-1 (xv)(Lead content (as Pb) ppm, Max)	-	0	-
Cl-5.4, Table-1 (xvi)(Hydrolysis resistance,(4) cut growth at 150 000 flexes, mm, Max)	-	0	-
Cl-6.1.1, Table-2 (i)(Tear trength, N)	-	0	-
Cl-6.1.1, Table-2 (ii)(Flexing resistance, flexes)	-	0	-
Cl-6.1.1, Table-2 (iii)(Colour fastness to rubbing (marring/staining))	-	0	-
Cl-6.1.1, Table-2 (iv)(Colour fastness to water (contact method- multi fabrics))	-	0	-
Cl-6.1.1, Table-2 (v)(Water vapour permeability,mg/cm2 /h, Min Water vapour coefficient,mg/cm2 , Min)	-	0	-
Cl-6.1.1, Table-2 (vi)(Stitch tear strength, N/mm, Min)	-	0	-
Cl-6.1.1, Table-2 (vii)(Abrasion resistance)	-	0	-
Cl-6.1.2, Table-3 (i)(Colour fastness to light, Marring, Min)	-	0	-
Cl-6.1.2, Table-3 (ii)(Water resistance)	-	0	-
Cl-6.1.2, Table-3 (iii)(Flexing resistance, flexes at (-) 5 °C 25 000 flexes)	-	0	-
Cl-6.1.3, Table- 4 (i)(Breaking strength, N/mm, Min Elongation at break, percent, Min)	-	0	-
Cl-6.1.3, Table- 4 (ii)(Tear Strength, N, Min)	-	0	-
Cl-6.1.3, Table- 4 (iii)(Strength at needle perforation, N/mm, Min)	-	0	-
Cl-6.1.3, Table- 4 (iv)(Flexing resistance, Flexes)	-	0	-
Cl-6.1.3, Table- 4 (v)(Water vapour permeability (WVP), mg/cm2 /h, Min)	-	0	-
Cl-6.1.3, Table- 4 (vi)(Hydrolysis resistance)	-	0	-
Cl-6.1.3, Table- 4 (vii)(Abrasion resistance)	-	0	-
Cl-6.1.4, Table-5 (i)(Colour fastness to light, Marring, Min)	-	0	-
Cl-6.1.4, Table- 5 (ii)(Flexing resistance, flexes at (-) 5 ºC, s 25 000 flexes)	-	0	-
Cl-6.2, Table-6 (i)(Tear strength, N, Min)	-	0	-
Cl-6.2, Table-6 (ii)(Abrasion resistance)	-	0	-
Cl-6.2, Table-6 (iii)(Colour fastness rubbing (crocking))	-	0	-
Cl-6.2, Table-6 (iv)(Colour fastness to perspiration)	-	0	-
Cl-6.2, Table-6 (v)(Water vapour permeability, mg/cm2 /h, Min Water vapour coefficient, mg/cm2, Min)	-	0	-
Cl-6.3, Table-7 (i)(Flexing index, Min)	-	0	-
Cl-6.3, Table-7 (ii)(Abrasion resistance at 400 cycles)	-	0	-
Cl-6.3, Table-7 (iii)(Water absorption, mg/cm2 , Min Water desorption, percent, Min)	-	0	-
Cl-6.4, Table-8 (i)(Thickness, mm, Min)	-	0	-
Cl-6.4, Table-8 (ii)(Abrasion resistance)	-	0	-
Cl-6.4, Table-8 (iii)(Water absorption, mg/cm2 , Min Water desorption, percent, Min)	-	0	-
Cl-6.5.1, , Table-9 (i)(Flexing resistance)	-	0	-
Cl-6.5.1, , Table-9 (ii)(Hydrolysis resistance, cut growth at 150 000 flexes, mm, Max)	-	0	-
Cl-6.5.1, , Table-9 (iii)(Compression set, percent, Max)	-	0	-
Cl-6.5.2.1, Table-10 (i)(Grain crack index, Min)	-	0	-
Cl-6.5.2.1, Table-10 (ii)(Density, g/cm3 , Min)	-	0	-
Cl-6.5.2.1, Table-10 (iii)(Abrasion resistance, mm/kcs, Max)	-	0	-
Cl-6.5.2.2, Table-11 (i)(Water resistance, (dynamic method))	-	0	-
Cl-6.5.2.3, Table-12 (i)(Hardness, Min)	-	0	-
Cl-6.5.2.3, Table-12 (ii)(Density, g/cm3 , Max)	-	0	-
Cl-6.5.2.3, Table-12 (iii)(Abrasion resistance (volume loss), mm3 , Max)	-	0	-
Cl-6.5.2.3, Table-12 (iv)(Bond Strength between Rubber top-lift and adjacent material, N/mm, Min)	-	0	-
Cl-6.6, Table-13 (i)(Heat shrinkage, percent, Max)	-	0	-
Cl-6.6, Table-13 (ii)(Split tear strength, kg/25 mm, Min)	-	0	-
Cl-6.6, Table-13 (iii)(Compression set, percent, Max)	-	0	-
Cl-6.7, Table-14 (i)(Hardness, N)	-	0	-
Cl-6.7, Table-14 (ii)(Resilience, percent)	-	0	-
Cl-6.7, Table-14 (iii)(Moisture resistance, percent)	-	0	-
Cl-6.10, Table-17 (i)(Lace breaking strength, N, Min)	-	0	-
Cl-6.10, Table-17 (ii)(Lace tag strength, N, Min)	-	0	-
Cl-6.10, Table-17 (iii)(Lace to lace abrasion resistance, cycles)	-	0	-
Cl-6.10, Table-17 (iv)(Colour fastness to water for lace contact methodstaining Gray scale rate , Min)	-	0	-
Cl-6.10, Table-17 (v)(Corrosion resistance)	-	0	-
Cl-6.11, Table-18 (i)(Fatigue resistance, cycles, Min)	-	0	-
Cl-6.11, Table-18 (ii)(Security of puller attachment strength, N, Min)	-	0	-
Cl-6.11, Table-18 (iii)(Lateral load, N, Min)	-	0	-
Cl-6.11, Table-18 (iv)(End attachment strength, N, Min)	-	0	-
Cl-8.1(Marking)	-	0	-
Cl-6.7, Table-14 (iv)(Area shape retention, percent (a) Initial, Min b) After 10 collapsing load, Min)	-	0	-
Cl-6.7, Table-14 (v)(Adhesion strength, N/mm)	-	0	-
Cl-6.8, Table-15 (i)(Peel strength, N/mm a) Initial, Min b) After 5 000 wear cycles, Min)	-	0	-
Cl- 6.8, Table-15 (ii)(a) Shear strength, kPa b) Initial, Min)	-	0	-
Cl- 6.9, Table-16 (i)(Limit of useful extension, percent, Min)	-	0	-
Cl- 6.9, Table-16 (ii)(Needle strength, N/mm, Min)	-	0	-

15 May, 2027

-
-

8736

LILABA ANALYTICAL LABORATORIES LLP, SURAT

7137216

IS 456 (2000)

Plain and reinforced concrete - Code of practice (Fourth Revision)

All size

1750 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5.4 .2(pH)	-	100	+18%GST
5.4-Table-1 (iii)-IS: 3025(P-32)(Chloride)	-	150	+18%GST
5.4-Table-1 (ii)-IS: 3025(P-24)(Sulphate)	-	300	+18%GST
Cl 5.4 Table 1 (i)(Organic Solids)	-	300	+18%GST
Cl 5.4 Table 1 (ii)(Inorganic Solids)	-	300	+18%GST
5.4-Table-1 (v)-IS: 3025(P-17)(Suspended matter)	-	150	+18%GST
Cl 5.4 (b)(Alkalinity)	-	200	+18%GST
Cl 5.4 (a)(Acidity)	-	200	+18%GST
Cl 5.4 Table 1 (iii)(Sulphate)	-	300	+18%GST
Cl 5.4 Table 1 (iv)(Chloride)	-	150	+18%GST
Cl 5.4 Table 1 (v)(Suspended Matter)	-	150	+18%GST
Clause 5.4(Description)	-	50	+18%GST

11 Jun, 2026

-
-

8737

LILABA ANALYTICAL LABORATORIES LLP, SURAT

7137216

IS 15609 (2005)

Polyethylene flexible pouches for the packing of natural mineral water and packaged drinking water - Specification

200ml,250ml

11200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Material)	-	100	+ 18% GST
6.1.1(Description)	-	100	+ 18% GST
6.1.2(Film Form)	-	50	+ 18% GST
6.1.3(Winding of the Film )	-	50	+ 18% GST
6.1.4(Odour)	-	50	+ 18% GST
6.1.5 A-2 of IS: 2508:2016(Thickness)	-	100	+ 18% GST
6.1.6(Width)	-	100	+ 18% GST
6.1.7 IS: 9845:1998(Migration- a. Amount of extractive )	-	900	+ 18% GST
6.1.7 IS: 9845:1998(Migration- b. Colour migration)	-	900	+ 18% GST
6.1.8 Annex 4 of IS:2508:2016(Tensile Strength a. Lengthwise direction)	-	200	+ 18% GST
6.1.8 Annex 4 of IS:2508:2016(Tensile Strength b. Crosswise direction)	-	200	+ 18% GST
6.1.9 Annex 4 of IS:2508:2016(Elongation at break - a. Lengthwise direction)	-	200	+ 18% GST
6.1.9 Annex 4 of IS:2508:2016(Elongation at break - b. Crosswise direction)	-	200	+ 18% GST
6.1.10 Annex -6 of IS:2508:2016(Dart impact Resistance)	-	350	+ 18% GST
7.1 Annex E(Water Potability test (after 30 Days) a) Taste b) Odour)	-	1700	+ 18% GST
7.2 Annex F(Stack Load test)	-	200	+ 18% GST
7.3 Annex G(Drop test )	-	300	+ 18% GST
7.4 Annex H(Ink adhesion test for printed pouches)	-	200	+ 18% GST
7.5 Annex J(Product resistance test for printed pouches)	-	200	+ 18% GST
6.1.9(Elongation at Break)	-	400	+ 18% GST
CL 6.1.11.2 and 6.1.11.3, Table 3 (i)(Barium)	-	300	+ 18% GST
CL 6.1.11.2 and 6.1.11.3, Table 3 (ii)(Cobalt)	-	300	+ 18% GST
CL 6.1.11.2 and 6.1.11.3, Table 3 (iii)(Copper)	-	300	+ 18% GST
CL 6.1.11.2 and 6.1.11.3, Table 3 (iv)(Iron)	-	300	+ 18% GST
CL 6.1.11.2 and 6.1.11.3, Table 3 (v)(Lithium)	-	300	+ 18% GST
CL 6.1.11.2 and 6.1.11.3, Table 3 (vi)(Manganese)	-	300	+ 18% GST
CL 6.1.11.2 and 6.1.11.3, Table 3 (vii)(Zinc)	-	300	+ 18% GST
CL 6.1.11.2 and 6.1.11.3, Table 3 (viii)(Antimony)	-	450	+ 18% GST
CL 6.1.11.2 and 6.1.11.3, Table 3 (ix)(Phthalic acid, bis(2-ethylhexyl) ester (DEHP))	-	2550	+ 18% GST

11 Jun, 2026

-
-

8738

RTRC LIMITED, GURUGRAM

9177406

IS 17505 : Part 1 (2021)

Specification for Thermosetting Insulated Fire Survival Cables for Fixed Installation having Low Emission of Smoke and Corrosive Gases when Affected by Fire for Working Voltages upto and including 1100 Vac and 1500 Vdc

174000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 7.3, Table 1 to 5 of IS 8130:2013 & IS:10810 (Part 5)-1984(Conductor Resistance Test)	-	1500	-
Cl. 7.1.2 of IS 8130 : 2013 & IS:10810 (Part 1)-1984(Annealing Test (for copper))	-	1000	-
Cl. 7.1.1 of IS 8130:2013 & IS:10810 (Part 4)-1984(Persulphate Test for tinned copper)	-	1000	Additional charges, If applicable
IS 191:2007 & IS 440(Copper purity test)	-	9000	Additional charges, If applicable
Cl. 11,14,16, Table 4 and Table 6 of IS 17505 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	1500	Additional charge, Rs. 2000 /- For each additional core
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 36)-1984(Diameter of armour Wire)	-	1000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 37)-1984(Tensile strength and elongation at break)	-	1500	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 38)-1984(Torsion Test on galvanised steel wire for armouring)	-	1000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 39)-1984(Winding Test for Formed Wires)	-	1000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 40)-1984(Uniformity of Zinc coating on Round Steel Wires and Formed Steel Wires (Strips))	-	1500	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 41)-1984(Mass of Zinc coating on Round Steel Wires and Formed Steel Wires (Strips))	-	2500	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 42)-1984(Resistivity test)	-	1500	-
Table 1 and Table 2 of IS 17505 -1: 2021, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	1500	-
Cl 18.2 of IS 17505-1:2021 & IS:10810 (Part 45)-1984(High voltage test)	-	2500	-
Table 1 of IS 17505-1 :2021 & IS:10810 (Part 43)-1984(Insulation Resistance)	-	1500	-
Cl. 18.6 of IS 17505-1:2021 & IS:10810 (Part 58)-1998(Oxygen index)	-	2500	Not applicable for thermoset material
Cl. 18.7 of IS 17505-1:2021 & IS:10810 (Part 64)-2003(Temperature Index)	-	2500	Not applicable for thermoset material
Table-1 & Table-2 of IS 17505-1:2021 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	3500	-
Specification for thermosetting insulated fire survival cables for fixed installation having low emission of smoke and corrosive gases when affected by fire for working voltages upto and including 1100 V A.C. and 1500 V D.C(Hot deformation)	-	1500	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	4000	Additional charges, If applicable (For Insulation)
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	4000	Additional charges, If applicable (For Insulation)
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	6000	Additional charges, If applicable (For Insulation)
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	21000	Additional charges, If applicable (For Insulation)
Table 1 of IS 17505-1: 2021 & IS:10810 (Part 21)-1984(Cold impact test)	-	3000	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 30)-1984(Hot set test)	-	3000	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 13)-1984(Ozone Resistance test)	-	12500	-
Cl 18.5.1 of IS 17505-1 :2021 & IS:10810 (Part 61)-1988(Flame test on single cable)	-	3000	-
Table 1 of IS 17505-1:2021 & IS:10810 (Part 12)-1984(Shrinkage test)	-	1500	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	4000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	4000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	6000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	21000	-
Tabel 1 and 2 of IS 17505-1:2021 & IS:10810 (Part 7)-1984(Tensile strength and elongation at break.)	-	0	-
Tabel 1 and 2 of IS 17505-1:2021 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	0	-
Cl 18.6 of IS 17505-1: 2021 & IS:10810 (Part 58)-1998(Oxygen Index.)	-	2500	Not applicable for thermoset material
Cl 18.8 of IS 17505-1:2021 & IS:10810 (Part 64)-2003(Temperature Index)	-	2500	Not applicable for thermoset material
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 13)-1984(Ozone resistance test)	-	0	-
Table 2 of IS 17505-1:2021 & IS:10810 (Part 15)-1984(Hot deformation)	-	1500	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	0	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	0	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	0	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	0	-
Table 1 of IS 17505-1:2021 & IS:10810 (Part 12)-1984(Shrinkage test)	-	0	-
Cl 18.2of IS 17505-1:2021 & IS:10810 (Part 45)-1984.(High Voltage test.)	-	0	-
Cl 18.5of IS 17505-1:2021 & IS:10810 (Part 53)-1984(Flammability Test)	-	2500	-
Table-2 of IS 17505-1:2021 & IS:10810 (Part 20)-1984(Cold bend test)	-	2000	-
Table-2 of IS 17505-1:2021 & IS:10810 (Part 21)-1984(Cold impact test)	-	0	-
Cl 18.5 of IS 17505-1:2021 & IS:10810 (Part 61)-1988(Flammability Test)	-	0	-
Cl 18.9 of IS 17505-1:2021(Water immersion test ( effect of water on sheath of cable))	-	5500	-
Cl 18.8 of IS 17505-1:2021& IS:10810 (Part 63)-1993(Smoke density test)	-	10000	Smoke density test (3-meter cube)
Cl. 3.5, 18.4 & Annex-E of IS 17505-1:2021(Circuit integrity test under fire)	-	45000	-
Cl. 17.1 Table 9 (iv) e(Heat Shock)	-	1500	-
Cl. 17.1 Table 9 (iv) h(Water absorption (Gravimetric))	-	5500	-
Cl. 17.1 Table 9 (vii) b(Flame test on bunched cable)	-	8500	-
Cl. 17.1 Table 9 (ix)(Abrasion resistance test)	-	5500	-

03 Apr, 2027

-
-

8739

Bombay Textiles Research Association (BTRA), Mumbai

7130206

IS 17371 (2020)

Geosynthetics – Geogrids for flexible pavements – Specification

101135 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
1("Tensile strength at 2 percent strain, (MD × CD- IS 16635 20/20 30/30 40/40")	-	0	COVERED UNDER TENSILE STRENGTH
1("Tensile strength at 5 percent strain, (MD × CD- IS 16635 20/20 30/30 40/40")	-	0	COVERED UNDER TENSILE STRENGTH
1("Ultimate tensile strength, (MD × CD)- IS 16635 30/30 40/40 50/50 60/60 80/80 100/100")	-	3585	-
1(UV resistance, strength retained after 500 h exposure- IS 13162 (part 2))	-	52000	-
1(Chemical resistance, strength retained after 72 h immersion- IS 17363)	-	30000	-
2("Ultimate tensile strength, (MD × CD)- IS 16635 20/20 30/30 40/40")	-	0	-
2("Tensile strength at 2 percent strain, (MD × CD- IS 16635 20/20 30/30 40/40")	-	0	COVERED UNDER TENSILE STRENGTH
2("Tensile strength at 5 percent strain, (MD × CD- IS 16635 20/20 30/30 40/40")	-	0	COVERED UNDER TENSILE STRENGTH
2(UV resistance, strength retained after 500 h exposure- IS 13162 (part 2))	-	0	-
2(Chemical resistance, strength retained after 72 h immersion- IS 17363)	-	0	-
2("Junction strength- IS 17371 AnnexB 20/20 30/30 40/40")	-	1500	-
Clause No. 4.1(Geogrid Raw Materials)	-	3300	-
Clause No. 4.1(Carbon Black content of Geogrid)	-	750	-
Clause No. 4.4(PET Geogrid weight)	-	5500	-
Clause No. 4.4(PET Geogrid carboxyl end group content)	-	3000	-
Clause No. 4.5(Identification of Geogrid)	-	0	-
Clause No. 5.2, Table No. 1 (ii)(Tensile strength at 2 percent strain, (MD × CD) kN/m of PET Geogrids)	-	0	COVERED UNDER TENSILE STRENGTH
Clause No. 5.2, Table No. 1 (iii)(Tensile strength at 5 percent strain, (MD × CD) kN/m of PET Geogrids)	-	0	COVERED UNDER TENSILE STRENGTH
Clause No. 5.2, table No. 1 (iv)(UV resistance, strength retained after 500 h exposure of PET Geogrids)	-	0	-
Clause No. 5.2, Table No. 1 (v)(Chemical resistance, strength retained after 72 h immersion of PET Geogrids)	-	0	-
Clause No. 5.2, table No. 1 (vi)(Width of PET Geogrids)	-	500	-
Clause No. 5.2, Table No. 1 (vii)(Roll length of PET Geogrids)	-	500	-
Clause No. 5.2, Table No. 2 (i)(Ultimate tensile strength, (MD × CD) kN/m of PP Geogrids)	-	0	-
Clause No. 5.2, Table No. 2 (ii)(Tensile strength at 2 percent strain, (MD × CD) kN/m of PP Geogrids)	-	0	COVERED UNDER TENSILE STRENGTH
Clause No. 5.2, Table No. 2 (iii)(Tensile strength at 5 percent strain, (MD × CD) kN/m of PP Geogrids)	-	0	COVERED UNDER TENSILE STRENGTH
Clause No. 5.2, table No. 2 (iv)(UV resistance, strength retained after 500 h exposure of PP Geogrids)	-	0	-
Clause No. 5.2, Table No. 2 (v)(Chemical resistance, strength retained after 72 h immersion of PP Geogrids)	-	0	-
Clause No. 5.2, Table No. 2 (vi)(Junction strength, percent strength of original strength)	-	0	-
Clause No. 5.2, table No. 2 (vii)(Width of PP Geogrids)	-	0	-
Clause No. 5.2, Table No. 2 (viii)(Roll length of PP Geogrids)	-	0	-
4.1(MATERIALS - Geogrid materials shall be inert to all chemicals naturally found in commonly encountered soils not containing adverse solvents and at ambient temperatures)	-	0	-
4.2(MATERIALS - Geogrids shall be rendered resistant to UV. Rigid geogrids shall have minimum 2 percent (mass/mass) of carbon black content)	-	0	-
4.3(MATERIALS - The geogrid shall be resistant to commonly encountered chemicals and microorganisms (rot and mildew) normally found in soils and shall be stabilized against short term exposure to solar radiation)	-	0	-
4.4(MATERIALS - PET geogrids, it shall have average molecular weight more than or equal to 25,000 g/mol)	-	0	-
4.5(MATERIALS - Identification of Geogrid)	-	0	-
5.1(REQUIREMENTS FOR GEOGRIDS -Geogrids shall be dimensionally stable and able to retain their geometry under manufacture, transport, and installation)	-	500	-
5.2- Table 1- i)(REQUIREMENTS FOR PET GEOGRIDS - Ultimate tensile strength, (MD × CD) kN/m)	-	0	-
5.2- Table 1- ii)(REQUIREMENTS FOR PET GEOGRIDS - Tensile strength at 2 percent strain, (MD × CD) kN/m,)	-	0	COVERED UNDER TENSILE STRENGTH
5.2- Table 1- iii)(REQUIREMENTS FOR PET GEOGRIDS - Tensile strength at 5 percent strain, (MD × CD) kN/m,)	-	0	COVERED UNDER TENSILE STRENGTH
5.2- Table 1- iv)(REQUIREMENTS FOR PET GEOGRIDS - UV resistance, strength retained after 500 h exposure)	-	0	-
5.2- Table 1- v)(REQUIREMENTS FOR GEOGRIDS - Chemical resistance, strength retained after 72 h immersion)	-	0	-
5.2- Table 1- vi)(REQUIREMENTS FOR PET GEOGRIDS - Width)	-	0	-
5.2- Table 1- vii)(REQUIREMENTS FOR PET GEOGRIDS - Roll length)	-	0	-
5.2- Table 2- i)(REQUIREMENTS FOR PP GEOGRIDS - Ultimate tensile strength, (MD × CD) kN/m)	-	0	-
5.2- Table 2- ii)(REQUIREMENTS FOR PP GEOGRIDS - Tensile strength at 2 percent strain, (MD × CD) kN/m)	-	0	COVERED UNDER TENSILE STRENGTH
5.2- Table 2- iii)(REQUIREMENTS FOR PP GEOGRIDS - Tensile strength at 5 percent strain, (MD × CD) kN/m,)	-	0	COVERED UNDER TENSILE STRENGTH
5.2- Table 2- iv)(REQUIREMENTS FOR PP GEOGRIDS - UV resistance, strength retained after 500 h exposure)	-	0	-
5.2- Table 2- v)(REQUIREMENTS FOR PP GEOGRIDS - Chemical resistance, strength retained after 72 h immersion)	-	0	-
5.2- Table 2- vi)(REQUIREMENTS FOR PP GEOGRIDS - Junction strength, percent strength of original strength)	-	0	-
5.2- Table 2- vii)(REQUIREMENTS FOR PP GEOGRIDS - Width)	-	0	-
5.2- Table 2- vIii)(REQUIREMENTS FOR PET GEOGRIDS - Roll length)	-	0	-
1("Tensile strength at 2 percent strain, (MD × CD- IS 16635 20/20 30/30 40/40")	-	0	-
1("Tensile strength at 5 percent strain, (MD × CD- IS 16635 20/20 30/30 40/40")	-	0	-
1("Ultimate tensile strength, (MD × CD)- IS 16635 30/30 40/40 50/50 60/60 80/80 100/100")	-	0	-
1(UV resistance, strength retained after 500 h exposure- IS 13162 (part 2))	-	0	-
1(Chemical resistance, strength retained after 72 h immersion- IS 17363)	-	0	-
2("Ultimate tensile strength, (MD × CD)- IS 16635 20/20 30/30 40/40")	-	0	-
2("Tensile strength at 2 percent strain, (MD × CD- IS 16635 20/20 30/30 40/40")	-	0	-
2("Tensile strength at 5 percent strain, (MD × CD- IS 16635 20/20 30/30 40/40")	-	0	-
2(UV resistance, strength retained after 500 h exposure- IS 13162 (part 2))	-	0	-
2(Chemical resistance, strength retained after 72 h immersion- IS 17363)	-	0	-
2("Junction strength- IS 17371 AnnexB 20/20 30/30 40/40")	-	0	-
Clause No. 4.1(Geogrid Raw Materials)	-	0	-
Clause No. 4.1(Carbon Black content of Geogrid)	-	0	-
Clause No. 4.4(PET Geogrid weight)	-	0	-
Clause No. 4.4(PET Geogrid carboxyl end group content)	-	0	-
Clause No. 4.5(Identification of Geogrid)	-	0	-
Clause No. 5.2, Table No. 1 (ii)(Tensile strength at 2 percent strain, (MD × CD) kN/m of PET Geogrids)	-	0	-
Clause No. 5.2, Table No. 1 (iii)(Tensile strength at 5 percent strain, (MD × CD) kN/m of PET Geogrids)	-	0	-
Clause No. 5.2, table No. 1 (iv)(UV resistance, strength retained after 500 h exposure of PET Geogrids)	-	0	-
Clause No. 5.2, Table No. 1 (v)(Chemical resistance, strength retained after 72 h immersion of PET Geogrids)	-	0	-
Clause No. 5.2, table No. 1 (vi)(Width of PET Geogrids)	-	0	-
Clause No. 5.2, Table No. 1 (vii)(Roll length of PET Geogrids)	-	0	-
Clause No. 5.2, Table No. 2 (i)(Ultimate tensile strength, (MD × CD) kN/m of PP Geogrids)	-	0	-
Clause No. 5.2, Table No. 2 (ii)(Tensile strength at 2 percent strain, (MD × CD) kN/m of PP Geogrids)	-	0	-
Clause No. 5.2, Table No. 2 (iii)(Tensile strength at 5 percent strain, (MD × CD) kN/m of PP Geogrids)	-	0	-
Clause No. 5.2, table No. 2 (iv)(UV resistance, strength retained after 500 h exposure of PP Geogrids)	-	0	-
Clause No. 5.2, Table No. 2 (v)(Chemical resistance, strength retained after 72 h immersion of PP Geogrids)	-	0	-
Clause No. 5.2, Table No. 2 (vi)(Junction strength, percent strength of original strength)	-	0	-
Clause No. 5.2, table No. 2 (vii)(Width of PP Geogrids)	-	0	-
Clause No. 5.2, Table No. 2 (viii)(Roll length of PP Geogrids)	-	0	-
4.1(MATERIALS - Geogrid materials shall be inert to all chemicals naturally found in commonly encountered soils not containing adverse solvents and at ambient temperatures)	-	0	-
4.2(MATERIALS - Geogrids shall be rendered resistant to UV. Rigid geogrids shall have minimum 2 percent (mass/mass) of carbon black content)	-	0	-
4.3(MATERIALS - The geogrid shall be resistant to commonly encountered chemicals and microorganisms (rot and mildew) normally found in soils and shall be stabilized against short term exposure to solar radiation)	-	0	-
4.4(MATERIALS - PET geogrids, it shall have average molecular weight more than or equal to 25,000 g/mol)	-	0	-
4.5(MATERIALS - Identification of Geogrid)	-	0	-
5.1(REQUIREMENTS FOR GEOGRIDS -Geogrids shall be dimensionally stable and able to retain their geometry under manufacture, transport, and installation)	-	0	-
5.2- Table 1- i)(REQUIREMENTS FOR PET GEOGRIDS - Ultimate tensile strength, (MD × CD) kN/m)	-	0	-
5.2- Table 1- ii)(REQUIREMENTS FOR PET GEOGRIDS - Tensile strength at 2 percent strain, (MD × CD) kN/m,)	-	0	-
5.2- Table 1- iii)(REQUIREMENTS FOR PET GEOGRIDS - Tensile strength at 5 percent strain, (MD × CD) kN/m,)	-	0	-
5.2- Table 1- iv)(REQUIREMENTS FOR PET GEOGRIDS - UV resistance, strength retained after 500 h exposure)	-	0	-
5.2- Table 1- v)(REQUIREMENTS FOR GEOGRIDS - Chemical resistance, strength retained after 72 h immersion)	-	0	-
5.2- Table 1- vi)(REQUIREMENTS FOR PET GEOGRIDS - Width)	-	0	-
5.2- Table 1- vii)(REQUIREMENTS FOR PET GEOGRIDS - Roll length)	-	0	-
5.2- Table 2- i)(REQUIREMENTS FOR PP GEOGRIDS - Ultimate tensile strength, (MD × CD) kN/m)	-	0	-
5.2- Table 2- ii)(REQUIREMENTS FOR PP GEOGRIDS - Tensile strength at 2 percent strain, (MD × CD) kN/m)	-	0	-
5.2- Table 2- iii)(REQUIREMENTS FOR PP GEOGRIDS - Tensile strength at 5 percent strain, (MD × CD) kN/m,)	-	0	-
5.2- Table 2- iv)(REQUIREMENTS FOR PP GEOGRIDS - UV resistance, strength retained after 500 h exposure)	-	0	-
5.2- Table 2- v)(REQUIREMENTS FOR PP GEOGRIDS - Chemical resistance, strength retained after 72 h immersion)	-	0	-
5.2- Table 2- vi)(REQUIREMENTS FOR PP GEOGRIDS - Junction strength, percent strength of original strength)	-	0	-
5.2- Table 2- vii)(REQUIREMENTS FOR PP GEOGRIDS - Width)	-	0	-
5.2- Table 2- vIii)(REQUIREMENTS FOR PET GEOGRIDS - Roll length)	-	0	-

-
-

8740

BIS, Northern Regional Laboratory (NRL)

None

IS 14616 (1999)

Laminated veneer lumber specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 (Dimensions)	-
6.2 (Dimensions)	-

-
Test facility is complete

8741

Bharat Test House Pvt Ltd 1474 Sonipat Haryana

9135626

IS 2418 : Part 2 (2018)

Tubular fluorescent lamps for general lighting service: Part 2 performance requirements (Second Revision)

Tubular Fluorescent Lamps

45000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5 of IS 2418:2:2018(MECHANCIAL, PHYSICAL AND STARTING REQUIREMENTS)	-	500	5% discount for BIS
Cl 5.1.2 of IS 2418:2:2018(Caps)	-	500	5% discount for BIS
Cl 5.1.2 of IS 2418:2:2018(Caps)	-	500	5% discount for BIS
Cl 5.1.2 of IS 2418:2:2018(Caps)	-	500	5% discount for BIS
Cl 5.1.2 of IS 2418:2:2018(Caps)	-	500	5% discount for BIS
Cl 5.1.2 of IS 2418:2:2018(Caps)	-	500	5% discount for BIS
Cl 5.1.3 of IS 2418:2:2018(Dimensions)	-	500	5% discount for BIS
Cl 5.2 of IS 2418:2:2018( Starting Requirements)	-	750	5% discount for BIS
Cl 6 of IS 2418:2:2018(MARKING)	-	250	5% discount for BIS
Cl 6 of IS 2418:2:2018(MARKING)	-	250	5% discount for BIS
Cl 6 of IS 2418:2:2018(MARKING)	-	250	5% discount for BIS
Cl 6 of IS 2418:2:2018(MARKING)	-	250	5% discount for BIS
Cl 6 of IS 2418:2:2018(MARKING)	-	250	5% discount for BIS
Cl 6 of IS 2418:2:2018(MARKING)	-	250	5% discount for BIS
Cl 6 of IS 2418:2:2018(MARKING)	-	250	5% discount for BIS
Cl 6 of IS 2418:2:2018(MARKING)	-	250	5% discount for BIS
Cl 7.3 of IS 2418:2:2018(Visual Examination and Checking for Marking)	-	250	5% discount for BIS
Cl 7.4 of IS 2418:2:2018(Burning Test)	-	7500	5% discount for BIS
Cl 7.5 of IS 2418:2:2018(Starting Characteristics)	-	7500	5% discount for BIS
Cl 7.6 of IS 2418:2:2018(Test for Electrical Luminous and Colour Characteristics)	-	10000	5% discount for BIS
Cl 7.7 of IS 2418:2:2018(Chromaticity Co-ordinates )	-	10000	5% discount for BIS
Cl 7.8 of IS 2418:2:2018(Life and Lumen Maintenance)	-	7000	5% discount for BIS
Cl 7.8 of IS 2418:2:2018(Life and Lumen Maintenance)	-	7000	5% discount for BIS
Cl 7.8 of IS 2418:2:2018(Life and Lumen Maintenance)	-	7000	5% discount for BIS
Clause No. 7.8(Life and Lumen Maintenance)	-	7000	5% discount for BIS
Clause No. 7.7(Chromaticity Co-ordinates)	-	10000	5% discount for BIS
Clause No. 7.6(Test for Electrical Luminous and Colour Characteristics)	-	10000	5% discount for BIS
Clause No. 7.4 & & 7.5(Burning Test & Starting Characteristics)	-	15000	5% discount for BIS
Clause No. 7.3 (Visual Examination and Checking for Marking.)	-	250	5% discount for BIS
3.15(Routine Test)	-	0	-
7.1.3(Routine tests)	-	0	-
4.12 of IS 2418 : Part 1 (2018)(Information for Ballast Design)	-	0	-
4.11 of IS 2418 : Part 1 (2018)(Information for Luminaire Design)	-	0	-
7.1.3 of IS 2418 : Part 1 (2018)(Routine Tests)	-	0	-
3.9 of IS 2418 : Part 1 (2018)(Routine test)	-	0	-
4.2 of IS 2418 : Part 1 (2018(Marking.)	-	500	5% discount for BIS
4.3 of IS 2418 : Part 1 (2018)(Mechanical requirement for caps)	-	1500	5% discount for BIS
4.4 of IS 2418 : Part 1 (2018)(Insulation Resistance Measurement)	-	2500	5% discount for BIS
4.5 of IS 2418 : Part 1 (2018)(Electric strength)	-	4000	5% discount for BIS
4.6 of IS 2418 : Part 1 (2018)(Parts which can become accidentally live)	-	1250	5% discount for BIS
4.7 of IS 2418 : Part 1 (2018)(Resistance to heat & fire)	-	4250	5% discount for BIS
4.8 of IS 2418 : Part 1 (2018)(Creepage distance for caps)	-	1500	5% discount for BIS
4.9 of IS 2418 : Part 1 (2018)(Lamp cap temperature rise)	-	3500	5% discount for BIS
4.10 of IS 2418 : Part 1 (2018)(Lamp minimum overall length)	-	1500	5% discount for BIS
Cl 5 of IS 2418:2:2018(MECHANCIAL, PHYSICAL AND STARTING REQUIREMENTS)	-	0	-
Cl 5.1.2 of IS 2418:2:2018(Caps)	-	0	-
Cl 5.1.2 of IS 2418:2:2018(Caps)	-	0	-
Cl 5.1.2 of IS 2418:2:2018(Caps)	-	0	-
Cl 5.1.2 of IS 2418:2:2018(Caps)	-	0	-
Cl 5.1.2 of IS 2418:2:2018(Caps)	-	0	-
Cl 5.1.3 of IS 2418:2:2018(Dimensions)	-	0	-
Cl 5.2 of IS 2418:2:2018( Starting Requirements)	-	0	-
Cl 6 of IS 2418:2:2018(MARKING)	-	0	-
Cl 6 of IS 2418:2:2018(MARKING)	-	0	-
Cl 6 of IS 2418:2:2018(MARKING)	-	0	-
Cl 6 of IS 2418:2:2018(MARKING)	-	0	-
Cl 6 of IS 2418:2:2018(MARKING)	-	0	-
Cl 6 of IS 2418:2:2018(MARKING)	-	0	-
Cl 6 of IS 2418:2:2018(MARKING)	-	0	-
Cl 6 of IS 2418:2:2018(MARKING)	-	0	-
Cl 7.3 of IS 2418:2:2018(Visual Examination and Checking for Marking)	-	0	-
Cl 7.4 of IS 2418:2:2018(Burning Test)	-	0	-
Cl 7.5 of IS 2418:2:2018(Starting Characteristics)	-	0	-
Cl 7.6 of IS 2418:2:2018(Test for Electrical Luminous and Colour Characteristics)	-	0	-
Cl 7.7 of IS 2418:2:2018(Chromaticity Co-ordinates )	-	0	-
Cl 7.8 of IS 2418:2:2018(Life and Lumen Maintenance)	-	0	-
Cl 7.8 of IS 2418:2:2018(Life and Lumen Maintenance)	-	0	-
Cl 7.8 of IS 2418:2:2018(Life and Lumen Maintenance)	-	0	-
3.15(Routine Test)	-	0	-
7.1.3(Routine tests)	-	0	-
4.12 of IS 2418 : Part 1 (2018)(Information for Ballast Design)	-	0	-
4.11 of IS 2418 : Part 1 (2018)(Information for Luminaire Design)	-	0	-
7.1.3 of IS 2418 : Part 1 (2018)(Routine Tests)	-	0	-
3.9 of IS 2418 : Part 1 (2018)(Routine test)	-	0	-
4.2 of IS 2418 : Part 1 (2018(Marking.)	-	0	-
4.3 of IS 2418 : Part 1 (2018)(Mechanical requirement for caps)	-	0	-
4.4 of IS 2418 : Part 1 (2018)(Insulation Resistance Measurement)	-	0	-
4.5 of IS 2418 : Part 1 (2018)(Electric strength)	-	0	-
4.6 of IS 2418 : Part 1 (2018)(Parts which can become accidentally live)	-	0	-
4.7 of IS 2418 : Part 1 (2018)(Resistance to heat & fire)	-	0	-
4.8 of IS 2418 : Part 1 (2018)(Creepage distance for caps)	-	0	-
4.9 of IS 2418 : Part 1 (2018)(Lamp cap temperature rise)	-	0	-
4.10 of IS 2418 : Part 1 (2018)(Lamp minimum overall length)	-	0	-

19 Mar, 2026

-
-

8742

Sleen India Biz venture Private Limited, Agra

9139736

IS 17043 : Part 1 (2024)

Shoes - Specification Part 1 Shoes for Services

Shoes for Services

51500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.2(Design)	-	200	10% Discount on BIS samples.
Cl-4.3.1(Size)	-	200	10% Discount on BIS samples.
Cl-4.3.2(Weight)	-	200	10% Discount on BIS samples.
Cl-4.4(Height of Upper)	-	200	10% Discount on BIS samples.
Cl-4.5, S.Cl-4.5.2(Ergonomic Feature)	-	300	10% Discount on BIS samples.
Cl-4.5, S.Cl-4.5.3(Bond Strength)	-	500	10% Discount on BIS samples.
Cl-4.5, S.Cl-4.5.4(Slip Resistance)	-	1800	10% Discount on BIS samples.
Cl-4.5.5.1(Electrical Properties-Antistatic footwear)	-	2500	10% Discount on BIS samples.
Cl-4.5, S.Cl-4.5.6(Heat Insulation of Sole Complex)	-	1000	10% Discount on BIS samples.
Cl-4.5, S.Cl-4.5.7(Cold Insulation of Sole Complex)	-	1000	10% Discount on BIS samples.
Cl-4.6.1(Material)	-	100	10% Discount on BIS samples.
Cl-4.6.2(Tear Strength)	-	500	10% Discount on BIS samples.
Cl-4.6.3(Water Vapour Permeability and Coefficient)	-	1000	10% Discount on BIS samples.
Cl-4.6.4(Water Penetration and Water Absorption)	-	700	10% Discount on BIS samples.
Cl-4.7.1(Material)	-	100	10% Discount on BIS samples.
Cl-4.7.2(Tear Strength)	-	500	10% Discount on BIS samples.
Cl-4.7.3(Abrasion Resistance)	-	800	10% Discount on BIS samples.
Cl-4.7.4(Water Vapour Permeability and Coefficient)	-	1000	10% Discount on BIS samples.
Cl. 4.8.1(Material)	-	100	10% Discount on BIS samples.
Cl-4.8.2(Abrasion Resistance)	-	800	10% Discount on BIS samples.
Cl-4.8.3(Water Absorption and Desorption)	-	800	10% Discount on BIS samples.
Cl-4.9.3(Abrasion Resistance)	-	800	10% Discount on BIS samples.
Cl-4.10(Toe Puff and Counter Stiffener)	-	200	10% Discount on BIS samples.
Cl-4.11.1(Material)	-	100	10% Discount on BIS samples.
Cl-4.11.2(Tear Strength)	-	500	10% Discount on BIS samples.
Cl-4.12(Closing Thread)	-	400	10% Discount on BIS samples.
Cl-4.13.2(Thickness)	-	200	10% Discount on BIS samples.
Cl-4.13.3(Moulded Density)	-	300	10% Discount on BIS samples.
Cl-4.13.4(Hardness)	-	500	10% Discount on BIS samples.
Cl-4.13.5(Ageing Test)	-	1000	10% Discount on BIS samples.
Cl-4.13.6(Tear Strength)	-	500	10% Discount on BIS samples.
Cl-4.13.7(Abrasion Resistance)	-	800	10% Discount on BIS samples.
Cl-4.13.8(Flexing Resistance)	-	800	10% Discount on BIS samples.
Cl-4.14(Eyelet)	-	500	10% Discount on BIS samples.
Cl-4.15.2(Breaking Load and Tag Retention)	-	500	10% Discount on BIS samples.
Cl-5(Chemical Requirements)	-	30000	10% Discount on BIS samples.
Cl-7(Marking)	-	100	-

15 May, 2027

-
Included w.e.f. 06.09.2024

8743

BIS, Southern Regional Laboratory (SRL)

None

IS 2082 (2018)

Stationary storage type electric water heaters - Specification (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
(Cl.8 of IS 302-2-21:2011) (Protection Against Access to Live Parts)	-
(Cl.10 of IS 302-2-21: 2011) (Power Input & Current)	-

-
1 No Excluding Safety requirements as per IS 302 Part 2 are avaialble. Exluding tests of Construction as per Cl 22.10 to 22.103 and 22.113 , 22.114 as per IS 302-2-21, Standing Loss test (Cl 16),Hotwater output v) Reheating time vi) Mixing factor vii) Deviation ofdial calibration viii) Cyclic temperature variation, Endurance test.

8744

BIS, Southern Regional Laboratory (SRL)

None

IS 2556 : Part 6 (2021)

Vitreous China sanitary appliances - Specification: Part 6 Specific requirements of urinal and partition plates (fifth revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 6.1 (DIMENSIONS AND TOLERANCES)	-
Cl 7.7 ()	-
Cl 7.1.2 ()	-
Cl 8 ()	-
Clause 4 and Clause 9.5 of IS 2556 (Part 1) (Chemical resistance)	-

-
2 Nos. Advised wooden packing to avoid damage during transit.

8745

Testtex India Laboratories Private Limited, Noida

8138306

IS 15298 : Part 2 (2016)

Personal protective equipment: Part 2 safety footwear (Second Revision)

Safety Footwear

41475 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4,Table 1(Class I, IS 15298)	-	200	-
4,Table 1(Class II, IS 15298)	-	200	-
5.2,5.2.1, Fig 3(Design,General, IS 15298)	-	500	-
5.2.2, Fig 4(Height of Upper, ISO 20344 , 6.2)	-	300	-
5.2.3, Table 10 ,Design A(Seat Region)	-	300	-
5.3.1.1(Construction)	-	300	-
5.3.1.2(Upper/outer sole bond strength , ISO 20344 , 5.2)	-	700	-
5.3.2.1(General, EN 12568 OF 4.2.2.2)	-	300	-
5.3.2.2,Table 5(Internal length of toecaps , ISO 20344 , 5.3)	-	300	-
5.3.2.3,Table 6(Impact resistance of safety footwear,ISO 20344 , 5.4)	-	700	-
5.3.2.4 ,Table 6(Compression Resistance of safety footwear ,ISO20344 , 5.5)	-	700	-
5.3.2.5.1(Corrosion resistance of metallic toecaps ,ISO20344 , 5.6.2)	-	500	-
5.3.2.5.2(Non metallic toe caps ,EN 12568)	-	1000	-
5.3.3(Leak proofness ,ISO 20344 , 5.7)	-	500	-
5.3.4(Specific ergonomic feature ,ISO 20344 , 5.1)	-	1000	-
5.3.6(Innocuousness)	-	26500	-
5.4.1,Table 10(General)	-	300	-
5.4.2, Table 11(Thickness , ISO 20344 , 6.1 )	-	300	-
5.4.3, Table 12(Tear Strength, ISO 20344 , 6.3 )	-	500	-
5.4.4, Table 13(Tensile properties ,ISO 20344 , 6.4.1 )	-	500	-
5.4.5, Table 14(Flexing resistance ,ISO 20344,6.5)	-	1000	-
5.4.6(Water vapour permeability and coefficient,ISO 20344,6.6 & 6.8)	-	700	-
5.4.7(Ph Value ; ISO 20344,6.9)	-	500	-
5.4.8(Hydrolysis ; ISO 20344,6.10)	-	3500	-
5.4.9(Chromium VI content; ISO 17075)	-	750	-
5.5.1,Table 15(Tear Strength, ISO 20344 , 6.3)	-	500	-
5.5.2(Abrasion Resistance ;ISO 20344 , 6.12)	-	700	-
5.5.3(Water vapour permeability and coefficient,ISO 20344,6.6 & 6.8)	-	700	-
5.5.4(Ph Value ; ISO 20344,6.9)	-	500	-
5.5.5(Chromium VI content; ISO 17075)	-	750	-
5.6.1,Table 16(Tear Strength, ISO 20344 , 6.3)	-	500	-
5.6.2(Ph Value ; ISO 20344,6.9)	-	500	-
5.6.3(Chromium VI content; ISO 17075)	-	750	-
5.7.1;Table 3(Thickness ; ISO 20344,7.1)	-	300	-
5.7.2(Ph Value ; ISO 20344,6.9)	-	500	-
5.7.3(Water Absorption and desorption ISO 20344,7.2 )	-	500	-
5.7.4.1(Insole ; ISO 20344,7.3 )	-	400	-
5.7.4.2(Insocks ; ISO 20344, 6.12)	-	700	-
5.7.5(Chromium VI content; ISO 17075)	-	750	-
5.8.1(Design, IS 15298 Part 2 )	-	0	-
5.8.1.1, Table 17(Thickness ; ISO 20344, 8.1.2)	-	300	-
5.8.1.2(Cleated area ; ISO 20344 , Fig 38)	-	300	-
5.8.1.3, Table 17(Cleat height; ISO 20344, 8.1)	-	300	-
5.8.2(Tear Strength, ISO 20344 , 8.2)	-	500	-
5.8.3(Abrasion Resistance ;ISO 20344 , 8.3)	-	700	-
5.8.4(Flexing resistance ,ISO 20344,8.4)	-	700	-
5.8.5(Hydrolysis ; ISO 20344,8.5)	-	3500	-
5.8.6(Interlayer bond strength; ISO 20344, 5.2)	-	700	-
6.2.1.1.1(Metallic anti-penetration insert; ISO 20344, 5.8.2)	-	1000	-
6.2.1.1.2(Non-metallic anti-penetration insert; ISO 20344, 5.8.3)	-	1000	-
6.2.1.2(Consruction)	-	200	-
6.2.1.3(Dimension ; ISO 20344, 5.8.1)	-	300	-
6.2.1.4(Flex resistance of penetration -resistant insert ; ISO 20344,5.9)	-	2500	-
6.2.1.5.1(Corrosion resistance of penetration -resistant metallic insert - ISO 20344, 5.6.3 &5.6.1)	-	500	-
6.2.1.5.2(Penetration -resistant non-metallic insert ; EN 12568,6.4&7.4)	-	1000	-
6.2.2.1 (Conductive footwear ; ISO 20344,5.10 & 5.10.3.3)	-	1000	-
6.2.2.2(Antistatic footwear ; ISO 20344,5.10)	-	1000	-
6.2.3.1(Hear insulation of sole complex; ISO 20344,5.12 ;Annex B)	-	700	-
6.2.3.2(Cold insulation of sole complex; ISO 20344,5.13)	-	700	-
6.2.4(Energy absorption of seat region; ISO 20344,5.14)	-	2000	-
6.2.5(Water resistance ; 5.15.1 & 5.15.2)	-	500	-
6.2.6.1(Construction)	-	200	-
6.2.6.2 , Table 19(Impact resistance of metatarsal protective device,ISO 20344 , 5.16)	-	3000	-
6.2.8.1(Design)	-	0	-
6.2.8.2(Construction)	-	0	-
6.2.8.3,EN 388(Resistance to cutting ,EN 388)	-	2500	-
6.2.8.4(Penetration Resistance)	-	1000	-
6.3(Upper--Water penetration and absorption ; ISO 20344 , 5.13)	-	1000	-
6.4.1(Resistance to hot contact ; ISO 20344 , 8.7)	-	700	-
6.4.2(Resistance to fuel oil ; ISO 20344 , 8.6.1& 8.6.2 ; )	-	700	-
5.6(Tongue - IS 15298 Part 2 )	-	0	-
Cl.7, table 2,table 18,table 20, table21, EN 13832-1,EN 13832-3: 2006,6.2.2.3(Marking)	-	0	-
8(Information to be supplied)	-	0	-
Cl.8.1 IS 15298 Part 2:2016 + A1:2019 + A2:2019, ISO 20345 :2011(General)	-	0	-
8.2(Electrical Properties)	-	0	-
8.2.2(Antistatic footwear)	-	0	-
8.3(Insocks)	-	0	-
Cl.5.7.3(Water absorption and desorption)	-	0	-
Cl.5.7.2(PH value)	-	0	-
5.5.1(Tear strength)	-	0	-
5.5.2(Abrasion Resistance)	-	0	-
5.5.3(W.V.P & W.V.C)	-	0	-
5.7.1(Insole thickness)	-	0	-
5.7.4.2(Insock abrasion)	-	0	-
5.8.1.2(Cleated area)	-	0	-
5.8.4(Flexing resistance)	-	0	-
5.8.1.1(Thickness)	-	0	-
5.8.1.3(Cleat height)	-	0	-
4,Table 1(Class I, IS 15298)	-	0	Clause Repeated
4,Table 1(Class II, IS 15298)	-	0	Clause Repeated
5.2,5.2.1, Fig 3(Design,General, IS 15298)	-	0	Clause Repeated
5.2.2, Fig 4(Height of Upper, ISO 20344 , 6.2)	-	0	Clause Repeated
5.2.3, Table 10 ,Design A(Seat Region)	-	0	Clause Repeated
5.3.1.1(Construction)	-	0	Clause Repeated
5.3.1.2(Upper/outer sole bond strength , ISO 20344 , 5.2)	-	0	Clause Repeated
5.3.2.1(General, EN 12568 OF 4.2.2.2)	-	0	Clause Repeated
5.3.2.2,Table 5(Internal length of toecaps , ISO 20344 , 5.3)	-	0	Clause Repeated
5.3.2.3,Table 6(Impact resistance of safety footwear,ISO 20344 , 5.4)	-	0	Clause Repeated
5.3.2.4 ,Table 6(Compression Resistance of safety footwear ,ISO20344 , 5.5)	-	0	Clause Repeated
5.3.2.5.1(Corrosion resistance of metallic toecaps ,ISO20344 , 5.6.2)	-	0	Clause Repeated
5.3.2.5.2(Non metallic toe caps ,EN 12568)	-	0	Clause Repeated
5.3.3(Leak proofness ,ISO 20344 , 5.7)	-	0	Clause Repeated
5.3.4(Specific ergonomic feature ,ISO 20344 , 5.1)	-	0	Clause Repeated
5.3.6(Innocuousness)	-	0	Clause Repeated
5.4.1,Table 10(General)	-	0	Clause Repeated
5.4.2, Table 11(Thickness , ISO 20344 , 6.1 )	-	0	Clause Repeated
5.4.3, Table 12(Tear Strength, ISO 20344 , 6.3 )	-	0	Clause Repeated
5.4.4, Table 13(Tensile properties ,ISO 20344 , 6.4.1 )	-	0	Clause Repeated
5.4.5, Table 14(Flexing resistance ,ISO 20344,6.5)	-	0	Clause Repeated
5.4.6(Water vapour permeability and coefficient,ISO 20344,6.6 & 6.8)	-	0	Clause Repeated
5.4.7(Ph Value ; ISO 20344,6.9)	-	0	Clause Repeated
5.4.8(Hydrolysis ; ISO 20344,6.10)	-	0	Clause Repeated
5.4.9(Chromium VI content; ISO 17075)	-	0	Clause Repeated
5.5.1,Table 15(Tear Strength, ISO 20344 , 6.3)	-	0	Clause Repeated
5.5.2(Abrasion Resistance ;ISO 20344 , 6.12)	-	0	Clause Repeated
5.5.3(Water vapour permeability and coefficient,ISO 20344,6.6 & 6.8)	-	0	Clause Repeated
5.5.4(Ph Value ; ISO 20344,6.9)	-	0	Clause Repeated
5.5.5(Chromium VI content; ISO 17075)	-	0	Clause Repeated
5.6.1,Table 16(Tear Strength, ISO 20344 , 6.3)	-	0	Clause Repeated
5.6.2(Ph Value ; ISO 20344,6.9)	-	0	Clause Repeated
5.6.3(Chromium VI content; ISO 17075)	-	0	Clause Repeated
5.7.1;Table 3(Thickness ; ISO 20344,7.1)	-	0	Clause Repeated
5.7.2(Ph Value ; ISO 20344,6.9)	-	0	Clause Repeated
5.7.3(Water Absorption and desorption ISO 20344,7.2 )	-	0	Clause Repeated
5.7.4.1(Insole ; ISO 20344,7.3 )	-	0	Clause Repeated
5.7.4.2(Insocks ; ISO 20344, 6.12)	-	0	Clause Repeated
5.7.5(Chromium VI content; ISO 17075)	-	0	Clause Repeated
5.8.1(Design, IS 15298 Part 2 )	-	0	Clause Repeated
5.8.1.1, Table 17(Thickness ; ISO 20344, 8.1.2)	-	0	Clause Repeated
5.8.1.2(Cleated area ; ISO 20344 , Fig 38)	-	0	Clause Repeated
5.8.1.3, Table 17(Cleat height; ISO 20344, 8.1)	-	0	Clause Repeated
5.8.2(Tear Strength, ISO 20344 , 8.2)	-	0	Clause Repeated
5.8.3(Abrasion Resistance ;ISO 20344 , 8.3)	-	0	Clause Repeated
5.8.4(Flexing resistance ,ISO 20344,8.4)	-	0	Clause Repeated
5.8.5(Hydrolysis ; ISO 20344,8.5)	-	0	Clause Repeated
5.8.6(Interlayer bond strength; ISO 20344, 5.2)	-	0	Clause Repeated
6.2.1.1.1(Metallic anti-penetration insert; ISO 20344, 5.8.2)	-	0	Clause Repeated
6.2.1.1.2(Non-metallic anti-penetration insert; ISO 20344, 5.8.3)	-	0	Clause Repeated
6.2.1.2(Consruction)	-	0	Clause Repeated
6.2.1.3(Dimension ; ISO 20344, 5.8.1)	-	0	Clause Repeated
6.2.1.4(Flex resistance of penetration -resistant insert ; ISO 20344,5.9)	-	0	Clause Repeated
6.2.1.5.1(Corrosion resistance of penetration -resistant metallic insert - ISO 20344, 5.6.3 &5.6.1)	-	0	Clause Repeated
6.2.1.5.2(Penetration -resistant non-metallic insert ; EN 12568,6.4&7.4)	-	0	Clause Repeated
6.2.2.1 (Conductive footwear ; ISO 20344,5.10 & 5.10.3.3)	-	0	Clause Repeated
6.2.2.2(Antistatic footwear ; ISO 20344,5.10)	-	0	Clause Repeated
6.2.3.1(Hear insulation of sole complex; ISO 20344,5.12 ;Annex B)	-	0	Clause Repeated
6.2.3.2(Cold insulation of sole complex; ISO 20344,5.13)	-	0	Clause Repeated
6.2.4(Energy absorption of seat region; ISO 20344,5.14)	-	0	Clause Repeated
6.2.5(Water resistance ; 5.15.1 & 5.15.2)	-	0	Clause Repeated
6.2.6.1(Construction)	-	0	Clause Repeated
6.2.6.2 , Table 19(Impact resistance of metatarsal protective device,ISO 20344 , 5.16)	-	0	Clause Repeated
6.2.8.1(Design)	-	0	Clause Repeated
6.2.8.2(Construction)	-	0	Clause Repeated
6.2.8.3,EN 388(Resistance to cutting ,EN 388)	-	0	Clause Repeated
6.2.8.4(Penetration Resistance)	-	0	Clause Repeated
6.3(Upper--Water penetration and absorption ; ISO 20344 , 5.13)	-	0	Clause Repeated
6.4.1(Resistance to hot contact ; ISO 20344 , 8.7)	-	0	Clause Repeated
6.4.2(Resistance to fuel oil ; ISO 20344 , 8.6.1& 8.6.2 ; )	-	0	Clause Repeated
5.6(Tongue - IS 15298 Part 2 )	-	0	Clause Repeated
Cl.7, table 2,table 18,table 20, table21, EN 13832-1,EN 13832-3: 2006,6.2.2.3(Marking)	-	0	Clause Repeated
8(Information to be supplied)	-	0	Clause Repeated
Cl.8.1 IS 15298 Part 2:2016 + A1:2019 + A2:2019, ISO 20345 :2011(General)	-	0	Clause Repeated
8.2(Electrical Properties)	-	0	Clause Repeated
8.2.2(Antistatic footwear)	-	0	Clause Repeated
8.3(Insocks)	-	0	Clause Repeated
Cl.5.7.3(Water absorption and desorption)	-	0	Clause Repeated
Cl.5.7.2(PH value)	-	0	Clause Repeated
5.5.1(Tear strength)	-	0	Clause Repeated
5.5.2(Abrasion Resistance)	-	0	Clause Repeated
5.5.3(W.V.P & W.V.C)	-	0	Clause Repeated
5.7.1(Insole thickness)	-	0	Clause Repeated
5.7.4.2(Insock abrasion)	-	0	Clause Repeated
5.8.1.2(Cleated area)	-	0	Clause Repeated
5.8.4(Flexing resistance)	-	0	Clause Repeated
5.8.1.1(Thickness)	-	0	Clause Repeated
5.8.1.3(Cleat height)	-	0	Clause Repeated
5.3.5.2,Table 7(Slip resistance on ceramic tile floor with sodium lauryl sulphate (NaLS) solution)	-	2000	-
5.3.5.3,Table 8(Slip resistance on steel floor with glycerin)	-	2000	-
5.3.5.4(Slip resistance on ceramic tile floor with NaLS and on steel floor with glycerin)	-	2000	-
Cl.5.3.5.1, Cl.5.3.5.2,Cl.5.3.5.3 or 5.3.5.4 IS 15298 (Part1):2015,ISO 20344:2011,5.11(General)	-	2000	-

31 Dec, 2026

-
Included w.e.f. 03.10.2024 Exclusion: for all types of footwear except electrically insulated footwear, ankle protection footwear, Cl.5.3.6 innocuousness allergenic and carcinogenic disperse dyes

8746

BCH Electric Limited, Faridabad

8186026

IS/IEC 60947 : Part 4 : Sec 1 (2012)

Low - Voltage switchgear and controlgear: Part 4 contactors and motor - Starters: Sec 1 electromechanical contactors and motor - Starters (First Revision)

Starter, Contactor, Thermal Overload Relay

3260000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.3.3.3.4 (Temperature rise of the main circuit )	-	30000	Only for internal testing
9.3.3.3.5( Temperature rise of control circuit)	-	20000	Only for internal testing
9.3.3.3.6( Temperature rise of coils and electromagnets )	-	20000	Only for internal testing
9.3.3.3.7 (Temperature rise of auxiliary circuits )	-	20000	Only for internal testing
9.3.3.4 (Dielectric properties )	-	50000	Only for internal testing
9.3.3.1(Ambient air temperatur)	-	20000	Only for internal testing
9.3.3.2(Operating limits)	-	50000	Only for internal testing
9.3.3.5("verification of rated making and breaking capacities, change-over ability and reversibility, where applicable")	-	100000	Only for internal testing
9.3.3.6(verification of conventional operational performance)	-	80000	Only for internal testing
9.3.5(Overload current withstand capability of contactors)	-	30000	Only for internal testing
9.2.2(Electrical performance of screwless-type clamping unit)	-	30000	Only for internal testing
9.1.2 (j) (Annex C of IEC 60947-1)(verification of degrees of protection of enclosed contactors and starters)	-	30000	Only for internal testing
B.3(Electrical durability)	-	120000	Only for internal testing
5.3.7 (Pole impedance of a contactor (Z) )	-	30000	Only for internal testing
5.2(Type of equipment )	-	10000	Only for internal testing
5.2.1(Kind of equipment)	-	20000	Only for internal testing
5.2.1(Kind of equipment)	-	10000	Only for internal testing
5.2.1(Kind of equipment)	-	10000	Only for internal testing
5.2.1(Kind of equipment)	-	10000	Only for internal testing
5.2.1(Kind of equipment)	-	10000	Only for internal testing
5.2.1(Kind of equipment)	-	10000	Only for internal testing
5.2.2(Number of poles)	-	10000	Only for internal testing
5.2.3(Kind of current)	-	10000	Only for internal testing
5.2.4 (Interrupting medium )	-	10000	Only for internal testing
5.2.5.1( Operating conditions of the equipment - Method of Operation)	-	10000	Only for internal testing
5.2.5.2(Method of control )	-	10000	Only for internal testing
5.3.1.1(Rated voltages : Rated operational voltage (Ue) )	-	20000	Only for internal testing
5.7.3 (Characteristic values : Release with shunt coil, under-voltage (under-current), over-voltage (instantaneous over current), current or voltage imbalance and phase reversal opening relay or release)	-	20000	Only for internal testing
5.7.3 (Characteristic values : Release with shunt coil, under-voltage (under-current), over-voltage (instantaneous over current), current or voltage imbalance and phase reversal opening relay or release)	-	20000	Only for internal testing
5.7.3 (Characteristic values : Release with shunt coil, under-voltage (under-current), over-voltage (instantaneous over current), current or voltage imbalance and phase reversal opening relay or release)	-	20000	Only for internal testing
5.7.3 (Characteristic values : Release with shunt coil, under-voltage (under-current), over-voltage (instantaneous over current), current or voltage imbalance and phase reversal opening relay or release)	-	20000	Only for internal testing
5.7.3 (Characteristic values : Release with shunt coil, under-voltage (under-current), over-voltage (instantaneous over current), current or voltage imbalance and phase reversal opening relay or release)	-	20000	Only for internal testing
5.2.5.3(Method of change-over for particular types of starters )	-	10000	Only for internal testing
5.2.5.4(Method of connecting for particular types of starters )	-	10000	Only for internal testing
5.3.1.1.1 (Rated stator operational voltage (Ues) )	-	10000	Only for internal testing
5.3.1.1.2( Rated rotor operational voltage (Uer) )	-	10000	Only for internal testing
5.3.1.3 (Rated impulse withstand voltage (Uimp) )	-	10000	Only for internal testing
5.3.1.4 (Rated starting voltage of an auto-transformer starter )	-	10000	Only for internal testing
5.3.2.1 (Conventional free air thermal current (Ith) )	-	10000	Only for internal testing
5.3.2.2 (Conventional enclosed thermal current (Ithe) )	-	10000	Only for internal testing
5.3.2.3( Conventional stator thermal current (Iths))	-	10000	Only for internal testing
5.3.2.4 (Conventional rotor thermal current (Ithr))	-	10000	Only for internal testing
5.3.2.5( Rated operational currents (Ie) or rated operational powers )	-	10000	Only for internal testing
5.3.2.6( Rated stator operational current (Ies) or rated stator operational power )	-	10000	Only for internal testing
5.3.2.7 (Rated rotor operational current (Ier) )	-	10000	Only for internal testing
5.3.2.8 (Rated uninterrupted current (Iu))	-	10000	Only for internal testing
5.3.3 (Rated frequency )	-	10000	Only for internal testing
5.3.4 (Rated duties )	-	10000	Only for internal testing
5.3.4.1 (Eight-hour duty (continuous duty)	-	20000	Only for internal testing
5.3.4.2 (Uninterrupted duty )	-	20000	Only for internal testing
5.3.4.4( Temporary duty )	-	20000	Only for internal testing
Cl.9.1.5.2 (Annex Q of IS/IEC 60947-1)(Special tests)	-	0	Testing facility not available
6.1.1( Identification)	-	10000	Only for internal testing
6.1.1( Identification)	-	10000	Only for internal testing
6.1.1( Identification)	-	10000	Only for internal testing
6.1.2(Characteristics: )	-	10000	Only for internal testing
6.1.2(Control circuits)	-	10000	Only for internal testing
6.1.2(Overload relays and releases)	-	10000	Only for internal testing
6.1.2(Overload relays and releases)	-	20000	Only for internal testing
6.1.2(Rheostatic rotor starters)	-	20000	Only for internal testing
6.1.2(Rheostatic rotor starters)	-	20000	Only for internal testing
6.1.2(Rheostatic rotor starters)	-	20000	Only for internal testing
6.1.2(Auto-transformer starters: )	-	20000	Only for internal testing
6.1.2(Vacuum contactors and starters: )	-	20000	Only for internal testing
6.1.2(Vacuum contactors and starters: )	-	20000	Only for internal testing
6.1.2(Vacuum contactors and starters: )	-	20000	Only for internal testing
6.2(Marking )	-	10000	Only for internal testing
5.10.1( Types : Time-delay devices)	-	10000	Only for internal testing
5.10.1( Types : Time-delay devices)	-	10000	Only for internal testing
5.10.1( Types : Time-delay devices)	-	10000	Only for internal testing
5.10.2 (Characteristics )	-	10000	Only for internal testing
5.10.2 (Characteristics )	-	10000	Only for internal testing
5.10.2 (Characteristics )	-	10000	Only for internal testing
5.11(Types and characteristics of auto-transformers for two-step auto-transformer starters )	-	10000	Only for internal testing
5.11(Types and characteristics of auto-transformers for two-step auto-transformer starters )	-	10000	Only for internal testing
5.11(Types and characteristics of auto-transformers for two-step auto-transformer starters )	-	10000	Only for internal testing
5.11(Types and characteristics of auto-transformers for two-step auto-transformer starters )	-	10000	Only for internal testing
5.11(Types and characteristics of auto-transformers for two-step auto-transformer starters )	-	10000	Only for internal testing
5.11(Types and characteristics of auto-transformers for two-step auto-transformer starters )	-	10000	Only for internal testing
5.12( Types and characteristics of starting resistors for rheostatic rotor starters )	-	10000	Only for internal testing
5.12( Types and characteristics of starting resistors for rheostatic rotor starters )	-	10000	Only for internal testing
5.12( Types and characteristics of starting resistors for rheostatic rotor starters )	-	10000	Only for internal testing
5.12( Types and characteristics of starting resistors for rheostatic rotor starters )	-	10000	Only for internal testing
5.7.3 (Characteristic values : Overload relay)	-	20000	Only for internal testing
5.5( Control circuit)	-	20000	Only for internal testing
5.5( Control circuit)	-	20000	Only for internal testing
5.5( Control circuit)	-	20000	Only for internal testing
5.5( Control circuit)	-	20000	Only for internal testing
5.5( Control circuit)	-	20000	Only for internal testing
5.5( Control circuit)	-	20000	Only for internal testing
5.6( Auxiliary circuits)	-	20000	Only for internal testing
5.7.2( Types of relay or releas)	-	20000	Only for internal testing
5.3.1.2 (Rated insulation voltage (Ui) )	-	20000	Only for internal testing
5.3.1.2.1 (Rated stator insulation voltage (Uis)	-	20000	Only for internal testing
5.3.1.2.2 (Rated rotor insulation voltage (Uir) )	-	20000	Only for internal testing
5.7.3 (Characteristic values : Overload relay)	-	20000	Only for internal testing
5.7.3 (Characteristic values : Overload relay)	-	20000	Only for internal testing
5.7.3 (Characteristic values : Overload relay)	-	20000	Only for internal testing
5.7.3 (Characteristic values : Overload relay)	-	20000	Only for internal testing
5.7.3 (Characteristic values : Overload relay)	-	20000	Only for internal testing
5.7.3 (Characteristic values : Overload relay)	-	20000	Only for internal testing
5.7.3 (Characteristic values : Release with residual current sensing relay:)	-	0	Testing facility not available
5.7.3 (Characteristic values : Release with residual current sensing relay:)	-	0	Testing facility not available
5.7.3 (Characteristic values : Release with residual current sensing relay:)	-	0	Testing facility not available
5.7.3 (Characteristic values : Release with residual current sensing relay:)	-	0	Testing facility not available
5.7.3 (Characteristic values : Release with residual current sensing relay:)	-	0	Testing facility not available
5.7.4( Designation and current settings of overload relays)	-	20000	Only for internal testing
5.7.5( Time-current characteristics of overload relays )	-	20000	Only for internal testing
5.7.6 (Influence of ambient air temperature )	-	20000	Only for internal testing
5.8(Co-ordination with short-circuit protective devices )	-	0	Testing facility not available
8.1.1(Constructional requirements : Genaral)	-	10000	Only for internal testing
8.1.2.1( General materials requirements )	-	20000	Only for internal testing
8.1.2.2 (Glow wire testing )	-	15000	Only for internal testing
8.1.2.3 (Test based on flammability category )	-	0	Testing facility not available
8.1.3( Current-carrying parts and their connections )	-	20000	Only for internal testing
8.1.4(Clearance)	-	10000	Only for internal testing
8.1.4( creepage distances )	-	10000	Only for internal testing
8.1.5(Actuator )	-	10000	Only for internal testing
8.1.5.1( Insulation)	-	10000	Only for internal testing
8.1.5.2 (Direction of movement)	-	10000	Only for internal testing
8.1.5.3( Mounting )	-	10000	Only for internal testing
8.1.6.1 (Indicating means )	-	10000	Only for internal testing
8.1.6.2( Indication by the actuator)	-	10000	Only for internal testing
8.1.7( Additional requirements for equipment suitable for isolation )	-	10000	Only for internal testing
8.1.8( Terminals)	-	10000	Only for internal testing
8.2.2.3 (Accessible part)	-	10000	Only for internal testing
8.2.2.4( Ambient air temperatur)	-	10000	Only for internal testing
9.1.2, (i) (8.2.4 of IEC 60947-1:2007)(Mechanical properties of terminals)	-	30000	Only for internal testing
7(Normal service, mounting and transport conditions )	-	15000	Only for internal testing
H.3(Limits of operation of control functions)	-	0	Testing facility not available
H.4(Test of the control functions)	-	0	Testing facility not available
F.7.2(Tests on products in a new condition)	-	0	Testing facility not available
F.7.3(Test after conventional operational performance)	-	40000	Only for internal testing
5.3.4.3 (Intermittent periodic duty or intermittent duty )	-	20000	Only for internal testing
5.3.4.5( Periodic duty )	-	20000	Only for internal testing
5.3.5.1 (Ability to withstand motor switching overload currents )	-	20000	Only for internal testing
5.3.5 (Normal load and overload characteristics )	-	20000	Only for internal testing
5.3.5.2 (Rated making capacity )	-	20000	Only for internal testing
5.3.5.3 (Rated breaking capacity )	-	20000	Only for internal testing
5.3.5.4 (Conventional operational performance )	-	100000	Only for internal testing
5.3.5.5( Starting and stopping characteristics of starters )	-	10000	Only for internal testing
5.3.5.5( Starting and stopping characteristics of starters )	-	20000	Only for internal testing
5.3.5.5( Starting and stopping characteristics of starters )	-	10000	Only for internal testing
5.3.5.5( Starting and stopping characteristics of starters )	-	10000	Only for internal testing
5.3.5.5( Starting and stopping characteristics of starters )	-	10000	Only for internal testing
5.3.5.5.1 (Starting characteristics of rheostatic rotor starters )	-	10000	Only for internal testing
5.3.5.5.2( Standard conditions for making and breaking corresponding to the starting characteristics for rheostatic rotor starters)	-	20000	Only for internal testing
5.3.5.5.3( Starting characteristics for two-step auto-transformer starters)	-	20000	Only for internal testing
8.1.10(Provisions for protective earthing)	-	0	Testing facility not available
8.1.11(Enclosures for equipment)	-	20000	Only for internal testing
8.1.12(Degrees of protection of enclosed equipment)	-	30000	Only for internal testing
8.1.9(Additional requirements for equipment provided with a neutral pole)	-	0	Testing facility not available
8.1.13(Conduit pull-out, torque and bending with metallic conduits)	-	0	Testing facility not available
B.2(Mechanical durability)	-	900000	Only for internal testing
9.2.3(Ageing test for screwless-type clamping units)	-	0	Testing facility not available
8.2.2(Temperature Rise)	-	30000	Only for internal testing
8.2.4.3(Durability)	-	90000	Only for internal testing
8.2.5.2(Co-ordination at the crossover current between starter and associated SCPD)	-	0	Testing facility not available
9.4.2(Immunity)	-	0	Testing facility not available (Under Exclusion)
9.4.3(Emission)	-	0	Testing facility not available (Under Exclusion)
9.4.1(General)	-	10000	only for internal testing
9.3.6.2(Operation and operating limits)	-	20000	only for internal testing
9.3.6.2(Operation and operating limits)	-	20000	only for internal testing
9.3.6.3(Dielectric tests)	-	20000	only for internal testing
9.3.3.2.1(Power-operated equipment)	-	30000	only for internal testing
9.3.3.2.1.2(Coil power consumption)	-	30000	only for internal testing
9.3.3.2.2(Relays and releases)	-	30000	only for internal testing
9.3.4.2.3(Leakage current Measurement)	-	15000	only for internal testing
9.3.4.2.3(Verification of dielectric Withstand)	-	20000	only for internal testing
9.3.4.2.3(Leakage current Measurement)	-	15000	only for internal testing
9.3.4(Performance under short-circuit conditions)	-	0	Testing facility not available ( short circuit test under exclusion)
9.2.1(General)	-	10000	only for internal testing
9.3.3.4.1( Type tests )	-	20000	only for internal testing
9.3.3.3.8 (Temperature rise of starting resistors for rheostatic rotor starters )	-	30000	only for internal testing
9.3.3.3.9( Temperature rise of the auto-transformer for two-step auto-transformer starters)	-	30000	only for internal testing
9.3.3.3.2 (Measurement of the temperature of parts )	-	30000	only for internal testing
9.3.3.3.3( Temperature rise of a part )	-	30000	only for internal testing
5.3.6 (Rated conditional short-circuit current)	-	0	Testing facility not available (short circuit test under exclusion)
5.4.1(Utilization category : General)	-	10000	only for internal testing
5.4.2(Assignment of utilization categories based on the results of tests )	-	10000	only for internal testing
5.4.2(Assignment of utilization categories based on the results of tests )	-	10000	only for internal testing
6.1.2(Safety and installation: )	-	10000	only for internal testing
5.3.5.5( Starting and stopping characteristics of starters )	-	10000	only for internal testing

05 Jun, 2028

-
Exclusion: 9.3.4 (Performance under short-circuit conditions), 9.4.2 (Immunity), 9.4.1 (General), 9.4.3 (Emission)

8747

Global Technical Services (Central Oil Testing Laboratory)

8188316

IS 11696 (2020)

Inhibited Type Spindle Oils ? Specification ( First Revision )

VG 2/5/10/15/22

3000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 3 Table 1(i)(Kinematics viscosity at 4O°C, cSt, )	-	500	-
Clause 3 Table 1(ii)(Viscosity index, Min)	-	500	-
Clause 3 Table 1(iv)(Flash point (PMCC), ºC, Min)	-	500	Remove this
Clause 3 Table 1(viii)(Total acidity, mg KOH/g, Max)	-	500	-
Clause 3 Table 1(vii)(Ash, percent by mass, Max)	-	500	-
Clause 3 Table 1(ix)(Inorganic acidity)	-	500	-
Clause 3 Table 1(x)(Copper strip corrosion at 100 ºC, for 3 h, Max)	-	500	-

19 Sep, 2028

-
-

8748

BCH Electric Limited, Faridabad

8186026

IS/IEC 60947 : PART 3 (2012)

Low - Voltage switchgear and controlgear: Part 3 switches, disconnectors, switch disconnectors and fuse - Combination units (First Revision)

SD F1/F2/F3 & SDF/FD/SFU 32-200A

3410000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.3.3.1(Temperature-rise)	-	25000	Test Lab for internal products.
8.3.3.2(Test of dielectric properties)	-	60000	Test Lab for internal products.
8.3.3.4(Dielectric verification)	-	30000	Test Lab for internal products.
8.3.3.5(Leakage current)	-	25000	Test Lab for internal products.
8.3.3.6(Temperature-rise verification)	-	25000	Test Lab for internal products.
8.3.3.7(Strength of actuator mechanism)	-	20000	Test Lab for internal products.
8.3.4.1.5(Operational performance test)	-	50000	Test Lab for internal products.
8.3.4.1.6(Operational performance test)	-	50000	Test Lab for internal products.
8.3.4.2(Dielectric verification)	-	25000	Test Lab for internal products.
8.3.4.3(Leakage current)	-	30000	Test Lab for internal products.
8.3.4.4(Temperature-rise verification)	-	25000	Test Lab for internal products.
8.3.5.3(Dielectric verification)	-	25000	Test Lab for internal products.
8.3.5.4(Leakage current)	-	30000	Test Lab for internal products.
8.3.5.5(Temperature-rise verification)	-	40000	Test Lab for internal products.
8.3.6.3(Dielectric verification)	-	25000	Test Lab for internal products.
8.3.6.4(Leakage current)	-	30000	Test Lab for internal products.
8.3.6.5(Temperature-rise verification)	-	40000	Test Lab for internal products.
8.3.7.2(Dielectric verification)	-	25000	Test Lab for internal products.
8.3.7.3(Leakage current)	-	30000	Test Lab for internal products.
8.3.7.4(Temperature-rise verification)	-	40000	Test Lab for internal products.
8.3.3.3.5(Behaviour of equipment during making and breaking capacity tests)	-	60000	Test Lab for internal products.
8.3.3.3.6(Condition of equipment after the making and breaking capacity tests)	-	60000	Test Lab for internal products.
3.1(Classification)	-	10000	Test Lab for internal products.
3.2(Classification)	-	10000	Test Lab for internal products.
3.3(Classification)	-	15000	Test Lab for internal products.
3.3(Classification)	-	15000	Test Lab for internal products.
4.1(Characteristics)	-	15000	Test Lab for internal products.
4.2(Characteristics)	-	15000	Test Lab for internal products.
4.3(Characteristics)	-	15000	Test Lab for internal products.
4.3.1.1(Characteristics)	-	15000	Test Lab for internal products.
4.3.1.2(Characteristics)	-	15000	Test Lab for internal products.
4.3.1.3(Characteristics)	-	15000	-
4.3.2(Characteristics)	-	15000	Test Lab for internal products.
4.3.2.1(Characteristics)	-	15000	Test Lab for internal products.
4.3.2.2(Characteristics)	-	15000	Test Lab for internal products.
4.3.2.3(Characteristics)	-	15000	Test Lab for internal products.
4.3.2.4(Characteristics)	-	15000	Test Lab for internal products.
4..3.3(Characteristics)	-	15000	Test Lab for internal products.
4..3.4.1(Characteristics)	-	15000	Test Lab for internal products.
4..3.4(Characteristics)	-	15000	Test Lab for internal products.
4..3.4.2(Characteristics)	-	15000	Test Lab for internal products.
4.3.5.1(Characteristics)	-	15000	Test Lab for internal products.
4.3.5.2(Characteristics)	-	15000	Test Lab for internal products.
4.3.5.3(Characteristics)	-	15000	Test Lab for internal products.
4.3.6.1(Characteristics)	-	15000	Test Lab for internal products.
4.3.6.2(Characteristics)	-	15000	Test Lab for internal products.
4.3.6.4(Characteristics)	-	15000	Test Lab for internal products.
4.4(Characteristics)	-	15000	Test Lab for internal products.
4.5(Characteristics)	-	15000	Test Lab for internal products.
4.6(Characteristics)	-	15000	Test Lab for internal products.
4.7(Characteristics)	-	15000	Test Lab for internal products.
4.8(Characteristics)	-	15000	Test Lab for internal products.
5.1(Product information)	-	15000	Test Lab for internal products.
5.2(Product information)	-	15000	Test Lab for internal products.
5.2.3(Product information)	-	15000	Test Lab for internal products.
5.2.4(Product information)	-	15000	Test Lab for internal products.
8.2.1.1.1(Test of resistance to abnormal heat and fire)	-	60000	Test Lab for internal products.
8.2.1.1.2(Test of resistance to abnormal heat and fire)	-	60000	Test Lab for internal products.
8.2.3(Enclosures for equipment)	-	20000	Test Lab for internal products.
8.2.4(Mechanical properties of terminals)	-	50000	Test Lab for internal products.
8.2.4.2(Tests of mechanical strength of terminals)	-	60000	Test Lab for internal products.
8.2.4.3(Testing for damage to and accidental loosening of conductors (flexion test))	-	60000	Test Lab for internal products.
8.2.4.4.1(Pull-out test)	-	50000	Test Lab for internal products.
8.2.4.4.2(Flat copper conductors)	-	40000	Test Lab for internal products.
8.1.3.2(Mechanical operation test)	-	70000	Test Lab for internal products.
8.1.3.3(Dielectric test)	-	60000	Test Lab for internal products.
8.1.4(Sampling tests)	-	30000	Test Lab for internal products.
8.3.3.1(Temperature-rise)	-	30000	Test Lab for internal products.
8.3.3.1(Temperature-rise)	-	30000	Test Lab for internal products.
8.3.3.1(Temperature-rise)	-	30000	Test Lab for internal products.
8.3.3.1(Temperature-rise)	-	30000	Test Lab for internal products.
8.3.3.2(Test of dielectric properties)	-	60000	Test Lab for internal products.
8.3.3.2(Test of dielectric properties)	-	60000	Test Lab for internal products.
8.3.3.2(Test of dielectric properties)	-	60000	Test Lab for internal products.
8.3.3.6(Temperature-rise verification)	-	30000	Test Lab for internal products.
8.3.3.6(Temperature-rise verification)	-	30000	Test Lab for internal products.
8.3.3.6(Temperature-rise verification)	-	30000	Test Lab for internal products.
8.3.3.6(Temperature-rise verification)	-	30000	Test Lab for internal products.
8.3.3.6(Temperature-rise verification)	-	30000	Test Lab for internal products.
8.3.3.6(Temperature-rise verification)	-	30000	Test Lab for internal products.
8.3.3.7(Strength of actuator mechanism)	-	25000	Test Lab for internal products.
8.3.4.4(Temperature-rise verification)	-	30000	Test Lab for internal products.
8.3.4.4(Temperature-rise verification)	-	30000	Test Lab for internal products.
8.3.4.4(Temperature-rise verification)	-	30000	Test Lab for internal products.
8.3.4.4(Temperature-rise verification)	-	30000	Test Lab for internal products.
8.3.4.4(Temperature-rise verification)	-	30000	Test Lab for internal products.
8.3.4.4(Temperature-rise verification)	-	30000	Test Lab for internal products.
8.3.5.1( Short-time withstand current test)	-	0	Facilities not available
8.3.5.1( Short-time withstand current test)	-	0	Facilities not available
8.3.5.2(Short-circuit making capacity test)	-	0	Facilities not available
8.3.5.2(Short-circuit making capacity test)	-	0	Facilities not available
8.3.5.5(Temperature-rise verification)	-	30000	Test Lab for internal products.
8.3.5.5(Temperature-rise verification)	-	30000	Test Lab for internal products.
8.3.5.5(Temperature-rise verification)	-	30000	Test Lab for internal products.
8.3.5.5(Temperature-rise verification)	-	30000	Test Lab for internal products.
8.3.5.5(Temperature-rise verification)	-	30000	Test Lab for internal products.
8.3.5.5(Temperature-rise verification)	-	30000	Test Lab for internal products.
8.3.6.2, 1 a)(Fuse protected short-circuit withstand)	-	0	Facilities not available
8.3.6.2, 1 a)(Fuse protected short-circuit withstand)	-	0	Facilities not available
8.3.6.5(Temperature-rise verification)	-	30000	Test Lab for internal products.
8.3.6.5(Temperature-rise verification)	-	30000	Test Lab for internal products.
8.3.6.5(Temperature-rise verification)	-	30000	Test Lab for internal products.
8.3.6.5(Temperature-rise verification)	-	30000	Test Lab for internal products.
8.3.6.5(Temperature-rise verification)	-	30000	Test Lab for internal products.
8.3.6.5(Temperature-rise verification)	-	30000	Test Lab for internal products.
8.3.7.1(Overload test)	-	10000	Test Lab for internal products.
8.3.7.4(Temperature-rise verification)	-	30000	Test Lab for internal products.
8.3.7.4(Temperature-rise verification)	-	30000	Test Lab for internal products.
8.3.7.4(Temperature-rise verification)	-	30000	Test Lab for internal products.
8.3.7.4(Temperature-rise verification)	-	30000	Test Lab for internal products.
8.3.7.4(Temperature-rise verification)	-	30000	Test Lab for internal products.
8.3.7.4(Temperature-rise verification)	-	30000	Test Lab for internal products.
8.4(Electromagnetic compatibility tests)	-	0	Facilities not available
8.4.1.2(Immunity (Equipment incorporating electronic circuits))	-	0	Facilities not available
8.4.1.2(Immunity (Equipment incorporating electronic circuits))	-	0	Facilities not available
8.4.1.2(Immunity (Equipment incorporating electronic circuits))	-	0	Facilities not available
8.4.1.2(Immunity (Equipment incorporating electronic circuits))	-	0	Facilities not available
8.4.1.2(Immunity (Equipment incorporating electronic circuits))	-	0	Facilities not available
8.4.2.2(Emission (Equipment incorporating electronic circuits ))	-	0	Facilities not available
8.5.1(Mechanical durability)	-	40000	Test Lab for internal products.
8.5.2(Electrical durability)	-	70000	Test Lab for internal products.
7.1(Constructional Requirements (except those covered under type tests))	-	40000	Test Lab for internal products.
8.3.3.3(Making and breaking capacities)	-	50000	Test Lab for internal products.
8.3.6.2, 1 b)(Fuse protected short-circuit making)	-	0	Facilities not available
7.3.2(Electrostatic discharge)	-	0	Facilities not available
7.3.2(Electrostatic discharge)	-	0	Facilities not available
7.3.2(Radiated RF Electromagnetic Field)	-	0	Facilities not available
7.3.2(Fast transient/ burst)	-	0	Facilities not available
7.3.2(Surge)	-	0	Facilities not available
7.3.2(Conducted disturbances induced by RF fields)	-	0	Facilities not available
7.3.2(Emission)	-	0	Facilities not available

05 Jun, 2028

-
Exclusion: 8.3.5.1 ( Short-time withstand current test), 8.3.5.2 (Short-circuit making capacity test)

8749

Global Technical Services (Central Oil Testing Laboratory)

8188316

IS 4578 (1997)

Lubricants - Lubricating oil for refrigeration machinery - Specification (Second Revision)

VG 15/22/32/46/68/100

3500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4.2(i)(Kinematic viscosity,cSt)	-	500	-
Clause 4.2(ii)(Flash point cleveland)	-	500	Remove this
Clause 4.2(v)a(Total, mg KOH/g , Max)	-	500	-
Clause 4.2(vi)(Ash content, percent by mass, Max)	-	500	-
Clause 4.2(vii)(Copper corrosion at lOO’C, for 3 h, MUX)	-	500	-
Clause 4.3(Viscosity Index)	-	500	-
Clause 3(Grades)	-	500	-
Clause 4.2(viii)(Water content)	-	500	-

19 Sep, 2028

-
-

8750

Global Technical Services (Central Oil Testing Laboratory)

8188316

IS 493 : Part 1 (2019)

Specification for general purpose machinery and spindle oils: Part 1 machinery oils (Second Revision)

VG 32 /46/68/100/150/220/320/460

2500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2 - Table 1 - (i)(Kinematic viscosity)	-	500	-
4.2 - Table 1 - (iv)(Flash point, Min)	-	500	Remove this
4.2 - Table 1 - (v)(Ash, Max)	-	500	-
4.2 - Table 1 - (vi)(Total Acidity, Max)	-	500	-
4.2 - Table 1 - (vii)(Inorganic acidity)	-	500	-
4.2 - Table 1 - (ix)(Copper strip corrosion)	-	500	-

19 Sep, 2028

-
-

8751

Atmy Analytical Labs Pvt. Ltd., Faridabad

8167506

IS 17043 : Part 1 (2024)

Shoes - Specification Part 1 Shoes for Services

50800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.2(Design)	-	50800	-
Cl-4.3.1(Size)	-	50800	-
Cl-4.3.2(Weight)	-	50800	-
Cl-4.5, S.Cl-4.5.2(Ergonomic Feature)	-	50800	-
Cl-4.5, S.Cl-4.5.3(Bond Strength)	-	50800	-
Cl-4.5, S.Cl-4.5.4(Slip Resistance)	-	50800	-
Cl-4.5.5.1(Electrical Properties-Antistatic footwear)	-	50800	-
Cl-4.5, S.Cl-4.5.6(Heat Insulation of Sole Complex)	-	50800	-
Cl-4.5, S.Cl-4.5.7(Cold Insulation of Sole Complex)	-	50800	-
Cl-4.6.1(Material)	-	50800	-
Cl-4.6.2(Tear Strength)	-	50800	-
Cl-4.6.3(Water Vapour Permeability and Coefficient)	-	50800	-
Cl-4.6.4(Water Penetration and Water Absorption)	-	50800	-
Cl-4.7.1(Material)	-	50800	-
Cl-4.7.2(Tear Strength)	-	50800	-
Cl-4.7.3(Abrasion Resistance)	-	50800	-
Cl-4.7.4(Water Vapour Permeability and Coefficient)	-	50800	-
Cl. 4.8.1(Material)	-	50800	-
Cl-4.8.2(Abrasion Resistance)	-	50800	-
Cl-4.8.3(Water Absorption and Desorption)	-	50800	-
Cl-4.9.3(Abrasion Resistance)	-	50800	-
Cl-4.10(Toe Puff and Counter Stiffener)	-	50800	-
Cl-4.11.1(Material)	-	50800	-
Cl-4.11.2(Tear Strength)	-	50800	-
Cl-4.12(Closing Thread)	-	50800	-
Cl-4.13.2(Thickness)	-	50800	-
Cl-4.13.3(Moulded Density)	-	50800	-
Cl-4.13.4(Hardness)	-	50800	-
Cl-4.13.5(Ageing Test)	-	50800	-
Cl-4.13.6(Tear Strength)	-	50800	-
Cl-4.13.7(Abrasion Resistance)	-	50800	-
Cl-4.13.8(Flexing Resistance)	-	50800	-
Cl-4.14(Eyelet)	-	50800	-
Cl-4.15.2(Breaking Load and Tag Retention)	-	50800	-
Cl-5(Chemical Requirements)	-	50800	-
Cl-7(Marking)	-	50800	-
Cl-4.4(Height of Upper)	-	50800	-
Cl-4.2(Design)	-	-	-
Cl-4.3.1(Size)	-	-	-
Cl-4.3.2(Weight)	-	-	-
Cl-4.4(Height of Upper)	-	-	-
Cl-4.5, S.Cl-4.5.2(Ergonomic Feature)	-	-	-
Cl-4.5, S.Cl-4.5.3(Bond Strength)	-	-	-
Cl-4.5, S.Cl-4.5.4(Slip Resistance)	-	-	-
Cl-4.5.5.1(Electrical Properties-Antistatic footwear)	-	-	-
Cl-4.5, S.Cl-4.5.6(Heat Insulation of Sole Complex)	-	-	-
Cl-4.5, S.Cl-4.5.7(Cold Insulation of Sole Complex)	-	-	-
Cl-4.6.1(Material)	-	-	-
Cl-4.6.2(Tear Strength)	-	-	-
Cl-4.6.3(Water Vapour Permeability and Coefficient)	-	-	-
Cl-4.6.4(Water Penetration and Water Absorption)	-	-	-
Cl-4.7.1(Material)	-	-	-
Cl-4.7.2(Tear Strength)	-	-	-
Cl-4.7.3(Abrasion Resistance)	-	-	-
Cl-4.7.4(Water Vapour Permeability and Coefficient)	-	-	-
Cl. 4.8.1(Material)	-	-	-
Cl-4.8.2(Abrasion Resistance)	-	-	-
Cl-4.8.3(Water Absorption and Desorption)	-	-	-
Cl-4.9.3(Abrasion Resistance)	-	-	-
Cl-4.10(Toe Puff and Counter Stiffener)	-	-	-
Cl-4.11.1(Material)	-	-	-
Cl-4.11.2(Tear Strength)	-	-	-
Cl-4.12(Closing Thread)	-	-	-
Cl-4.13.2(Thickness)	-	-	-
Cl-4.13.3(Moulded Density)	-	-	-
Cl-4.13.4(Hardness)	-	-	-
Cl-4.13.5(Ageing Test)	-	-	-
Cl-4.13.6(Tear Strength)	-	-	-
Cl-4.13.7(Abrasion Resistance)	-	-	-
Cl-4.13.8(Flexing Resistance)	-	-	-
Cl-4.14(Eyelet)	-	-	-
Cl-4.15.2(Breaking Load and Tag Retention)	-	-	-
Cl-5(Chemical Requirements)	-	-	-
Cl-7(Marking)	-	-	-
Cl.4.5.8(Energy Absorption of Seat Region)	-	-	-
Cl- 4.5.3.1(Upper-outsole bond strength)	-	-	-
Cl.4.5.3.2(Interlayer bond strength)	-	-	-
Cl-4.9.1(Material)	-	-	-
Cl-4.9.2(Water Absorption and Desorption)	-	-	-
Cl-4.13.1(Material)	-	-	-

25 Feb, 2027

-
Included w.e.f. 10.04.2024

8752

BIS, Western Regional Laboratory (WRL)

None

IS 12586 (2021)

Brazed low carbon steel gas cylinders not exceeding 13 litre water capacity Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.4 (Water capacity)	-
6.5 (Valve)	-
6.7 (Foot Ring)	-
8.2 (Leakage test)	-
12 (Marking)	-

-
Test facilities are not available for the following: (1) Peel Test

8753

National Test House (WR) - NTH, Mumbai

7107604

IS 302 : Part 2 : Sec 13 (1994)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 13 frying pans, deep fat fryers and similar appliances

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
32(Radiation ,Toxicity and similar hazards)	-	0	-
31(Resistance to Rusting)	-	1000	-
30(Resistance to Heat, Fire and Tracking)	-	1500	-
29(Clearances, Creepage Distances & Solid Insulation)	-	500	-
28(Screws & Connections)	-	1000	-
27(Provision For Earthing)	-	500	-
26(Terminals For External Conductors)	-	500	-
25(Supply Connection & External Flexible Cables and Cords)	-	1000	-
24(Components)	-	500	-
23(Internal wiring)	-	500	-
22(Construction)	-	500	-
21(Mechanical strength)	-	500	-
20(Stability & Mechanical Hazards)	-	500	-
19(Abnormal Operation)	-	2000	-
13(Leakage Current and Electric Strength at Operating Temperature)	-	500	-
11(Temperature Rise/Heating)	-	1000	-
10(Power Input)	-	500	-
9(Starting Of Motor Operated Appliances)	-	500	-
8(Protection against Electric Shock/ Protection against Access to Live Parts)	-	500	-
7(Marking/ Marking & Instructions)	-	500	-
6(Classification)	-	500	-
5(Rating)	-	500	-
18(Endurance)	-	1500	-
17(Overload Protection/ Overload Protection of Transformers & Associated Circuits)	-	500	-
16(Leakage Current and Electric Strength)	-	500	-
15(Moisture Resistance)	-	1000	-
14(Transient Over Voltage)	-	500	-
31(Resistance to Rusting)	-	500	-
30(Resistance to Heat, Fire and Tracking)	-	500	-
29(Clearances, Creepage Distances & Solid Insulation)	-	500	-
28(Screws & Connections)	-	500	-
27(Provision For Earthing)	-	500	-
26(Terminals For External Conductors)	-	500	-
25(Supply Connection & External Flexible Cables and Cords)	-	500	-
24(Components)	-	500	-
23(Internal wiring)	-	500	-
22(Construction)	-	500	-
21(Mechanical strength)	-	500	-
20(Stability & Mechanical Hazards)	-	500	-
19(Abnormal Operation)	-	500	-
13(Leakage Current and Electric Strength at Operating Temperature)	-	500	-
11(Temperature Rise/Heating)	-	1500	-
10(Power Input)	-	500	-
9(Starting Of Motor Operated Appliances)	-	1500	-
8(Protection against Electric Shock/ Protection against Access to Live Parts)	-	500	-
7(Marking/ Marking & Instructions)	-	500	-
6(Classification)	-	500	-
5(Rating)	-	500	-
18(Endurance)	-	1500	-
17(Overload Protection/ Overload Protection of Transformers & Associated Circuits)	-	500	-
16(Leakage Current and Electric Strength)	-	500	-
15(Moisture Resistance)	-	1000	-
14(Transient Over Voltage)	-	500	-
31(Resistance to Rusting)	-	500	-
30(Resistance to Heat, Fire and Tracking)	-	1000	-
29(Clearances, Creepage Distances & Solid Insulation)	-	500	-
28(Screws & Connections)	-	500	-
27(Provision For Earthing)	-	500	-
26(Terminals For External Conductors)	-	500	-
25(Supply Connection & External Flexible Cables and Cords)	-	500	-
24(Components)	-	500	-
23(Internal wiring)	-	500	-
22(Construction)	-	500	-
21(Mechanical strength)	-	500	-
20(Stability & Mechanical Hazards)	-	500	-
19(Abnormal Operation)	-	1500	-
13(Leakage Current and Electric Strength at Operating Temperature)	-	500	-
11(Temperature Rise/Heating)	-	1500	-
10(Power Input)	-	500	-
9(Starting Of Motor Operated Appliances)	-	500	-
8(Protection against Electric Shock/ Protection against Access to Live Parts)	-	500	-
7(Marking/ Marking & Instructions)	-	500	-
6(Classification)	-	500	-
5(Rating)	-	500	-
18(Endurance)	-	1500	-
17(Overload Protection/ Overload Protection of Transformers & Associated Circuits)	-	500	-
16(Leakage Current and Electric Strength)	-	500	-
15(Moisture Resistance)	-	1500	-
14(Transient Over Voltage)	-	500	-
31(Resistance to Rusting)	-	1000	-
30(Resistance to Heat, Fire and Tracking)	-	1500	-
29(Clearances, Creepage Distances & Solid Insulation)	-	1000	-
28(Screws & Connections)	-	1000	-
27(Provision For Earthing)	-	1000	-
26(Terminals For External Conductors)	-	500	-
25(Supply Connection & External Flexible Cables and Cords)	-	1000	-
24(Components)	-	1000	-
23(Internal wiring)	-	1000	-
22(Construction)	-	1000	-
21(Mechanical strength)	-	1000	-
20(Stability & Mechanical Hazards)	-	1000	-
19(Abnormal Operation)	-	1500	-
13(Leakage Current and Electric Strength at Operating Temperature)	-	1000	-
11(Temperature Rise/Heating)	-	1500	-
10(Power Input)	-	1500	-
9(Starting Of Motor Operated Appliances)	-	1000	-
8(Protection against Electric Shock/ Protection against Access to Live Parts)	-	1000	-
7(Marking/ Marking & Instructions)	-	1000	-
6(Classification)	-	500	-
5(Rating)	-	500	-
18(Endurance)	-	2000	-
17(Overload Protection/ Overload Protection of Transformers & Associated Circuits)	-	1000	-
16(Leakage Current and Electric Strength)	-	1000	-
15(Moisture Resistance)	-	1500	-
14(Transient Over Voltage)	-	1000	-
31(Resistance to Rusting)	-	1000	-
30(Resistance to Heat, Fire and Tracking)	-	1000	-
29(Clearances, Creepage Distances & Solid Insulation)	-	1000	-
28(Screws & Connections)	-	1000	-
27(Provision For Earthing)	-	1000	-
26(Terminals For External Conductors)	-	1000	-
25(Supply Connection & External Flexible Cables and Cords)	-	1000	-
24(Components)	-	1000	-
23(Internal wiring)	-	1000	-
22(Construction)	-	1000	-
21(Mechanical strength)	-	1000	-
20(Stability & Mechanical Hazards)	-	1000	-
19(Abnormal Operation)	-	2000	-
13(Leakage Current and Electric Strength at Operating Temperature)	-	1000	-
11(Temperature Rise/Heating)	-	1000	-
10(Power Input)	-	500	-
9(Starting Of Motor Operated Appliances)	-	500	-
8(Protection against Electric Shock/ Protection against Access to Live Parts)	-	500	-
7(Marking/ Marking & Instructions)	-	500	-
6(Classification)	-	500	-
5(Rating)	-	500	-
18(Endurance)	-	2000	-
17(Overload Protection/ Overload Protection of Transformers & Associated Circuits)	-	1000	-
16(Leakage Current and Electric Strength)	-	1000	-
15(Moisture Resistance)	-	1000	-
14(Transient Over Voltage)	-	1000	-
31(Resistance to Rusting)	-	500	-
30(Resistance to Heat, Fire and Tracking)	-	500	-
29(Clearances, Creepage Distances & Solid Insulation)	-	500	-
28(Screws & Connections)	-	500	-
27(Provision For Earthing)	-	500	-
26(Terminals For External Conductors)	-	500	-
25(Supply Connection & External Flexible Cables and Cords)	-	500	-
24(Components)	-	500	-
23(Internal wiring)	-	500	-
22(Construction)	-	1000	-
21(Mechanical strength)	-	1000	-
20(Stability & Mechanical Hazards)	-	1000	-
19(Abnormal Operation)	-	1000	-
13(Leakage Current and Electric Strength at Operating Temperature)	-	1000	-
11(Temperature Rise/Heating)	-	1000	-
10(Power Input)	-	1000	-
9(Starting Of Motor Operated Appliances)	-	1000	-
8(Protection against Electric Shock/ Protection against Access to Live Parts)	-	1000	-
7(Marking/ Marking & Instructions)	-	500	-
6(Classification)	-	500	-
5(Rating)	-	500	-
18(Endurance)	-	1000	-
17(Overload Protection/ Overload Protection of Transformers & Associated Circuits)	-	1000	-
16(Leakage Current and Electric Strength)	-	1000	-
15(Moisture Resistance)	-	1000	-
14(Transient Over Voltage)	-	1000	-
31(Resistance to Rusting)	-	500	-
30(Resistance to Heat, Fire and Tracking)	-	500	-
29(Clearances, Creepage Distances & Solid Insulation)	-	500	-
28(Screws & Connections)	-	500	-
27(Provision For Earthing)	-	500	-
26(Terminals For External Conductors)	-	500	-
25(Supply Connection & External Flexible Cables and Cords)	-	500	-
24(Components)	-	500	-
23(Internal wiring)	-	500	-
22(Construction)	-	500	-
21(Mechanical strength)	-	500	-
20(Stability & Mechanical Hazards)	-	500	-
19(Abnormal Operation)	-	1000	-
13(Leakage Current and Electric Strength at Operating Temperature)	-	500	-
11(Temperature Rise/Heating)	-	1000	-
10(Power Input)	-	500	-
9(Starting Of Motor Operated Appliances)	-	500	-
8(Protection against Electric Shock/ Protection against Access to Live Parts)	-	500	-
7(Marking/ Marking & Instructions)	-	500	-
6(Classification)	-	500	-
5(Rating)	-	500	-
18(Endurance)	-	1500	-
17(Overload Protection/ Overload Protection of Transformers & Associated Circuits)	-	500	-
16(Leakage Current and Electric Strength)	-	500	-
15(Moisture Resistance)	-	500	-
14(Transient Over Voltage)	-	500	-
19.11.4.3(Fast transient bursts)	-	500	-
19.11.4.4(Surge immunity test)	-	500	-
19.11.4.5(Immunity to conducted discharges)	-	500	-
19.11.4.6(Class 3 Voltage dips and interruptions)	-	500	-
19.11.4.7(Harmonics)	-	500	-

24 Jul, 2025

-
Included w.e.f. 31.07.2024 Exclusion: Cl. 32 (Radiation ,Toxicity and similar hazards), Cl. 19.11.4.1 (Electrostatic discharges), Cl. 19.11.4.2 (Radiated fields)

8754

National Test House (WR) - NTH, Mumbai

7107604

IS 367 (1993)

Electric kettles and jugs for household and similar use - Specification (Fourth Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9(Safety Requirements)	-	1500	-
11(Overall Dimensions)	-	1000	-
12(Mass)	-	1000	-
13(Water Capacity)	-	1000	-
14(Time to boil one litre of water)	-	1000	-
15(Time to boil water capacity)	-	1000	-
16(Minimum quantity of water that can be boiled)	-	1000	-
17(Temperature of supporting surface)	-	2000	-
18(Thermal Efficiency)	-	1500	-
19(Endurance)	-	3000	-
20(Finish)	-	500	-
6(Rating)	-	500	-
7(Classification)	-	500	-
8(Marking and Instruction)	-	1000	-
9(Safety Requirements)	-	500	-
11(Overall Dimensions)	-	500	-
12(Mass)	-	500	-
13(Water Capacity)	-	500	-
14(Time to boil one litre of water)	-	500	-
15(Time to boil water capacity)	-	500	-
16(Minimum quantity of water that can be boiled)	-	500	-
17(Temperature of supporting surface)	-	500	-
18(Thermal Efficiency)	-	1000	-
19(Endurance)	-	3000	-
20(Finish)	-	500	-
6(Rating)	-	500	-
7(Classification)	-	500	-
8(Marking and Instruction)	-	500	-
Cl-9 (Cl-8 of IS 302-2-15)(PROTECTION AGAINST ACCESS TO LIVE PARTS)	-	500	-
Cl-9 (Cl-10 of IS 302-2-15)(POWER INPUT AND CURRENT)	-	500	-
Cl-9 (Cl-11 of IS 302-2-15)(HEATING)	-	500	-
Cl-9 (Cl-13 of IS 302-2-15)(LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING TEMPERATURE)	-	500	-
Cl-9 (Cl-14 of IS 302-2-15)(TRANSIENT OVER VOLTAGES)	-	500	-
Cl-9 (Cl-15 of IS 302-2-15)(MOISTURE RESISTANCE)	-	1000	-
Cl-9 (Cl-16 of IS 302-2-15)(LEAKAGE CURRENT AND ELECTRIC STRENGTH)	-	500	-
Cl-9 (Cl-17 of IS 302-2-15)(OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS)	-	500	-
Cl-9 (Cl-19 of IS 302-2-15)(ABNORMAL OPERATION)	-	1000	-
Cl-9 (Cl-20 of IS 302-2-15)(STABILITY AND MECHANICAL HAZARDS)	-	500	-
Cl-9 (Cl-21 of IS 302-2-15)(MECHANICAL STRENGTH)	-	500	-
Cl-9 (Cl-22 of IS 302-2-15)(CONSTRUCTION)	-	500	-
Cl-9 (Cl-23 of IS 302-2-15)(INTERNAL WIRING)	-	500	-
Cl-9 (Cl-24 of IS 302-2-15)(COMPONENTS)	-	500	-
Cl-9 (Cl-25 of IS 302-2-15)(SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CORDS)	-	500	-
Cl-9 (Cl-26 of IS 302-2-15)(TERMINALS FOR EXTERNAL CONDUCTORS)	-	500	-
Cl-9 (Cl-27 of IS 302-2-15)(PROVISION FOR EARTHING)	-	500	-
Cl-9 (Cl-28 of IS 302-2-15)(SCREWS AND CONNECTIONS)	-	500	-
Cl-9 (Cl-29 of IS 302-2-15)(CLEARANCES, CREEPAGE DISTANCES AND SOLID INSULATION)	-	500	-
Cl-9 (Cl-30 of IS 302-2-15)(RESISTANCE TO HEAT AND FIRE)	-	500	-
Cl-9 (Cl-31 of IS 302-2-15)(RESISTANCE TO RUSTING)	-	500	-

24 Jul, 2025

-
Included w.e.f. 26.06.2027 Exclusion: Cl.9 (Cl.32 of 302-2-15) Radiation, Toxicity and Similar Hazards

8755

BCH Electric Limited, Faridabad

8186026

IS/IEC 60947 : Part 2 (2016)

Low - Voltage switchgear and controlgear: Part 2 circuit - Breakers (First Revision)

F1-TUMU/F2-TMTU/F3-TMTU/F3-LSIG/F2-LSIG MCCB

1674000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.3.3.2(Tripping limits and characteristics)	-	100000	only for internal testing
8.3.3.3(Test of dielectric properties)	-	65000	only for internal testing
8.3.3.4(Mechanical operation and operational performance capability)	-	90000	only for internal testing
8.3.3.5(Overload performance)	-	150000	only for internal testing
8.3.3.6(Verification of dielectric withstand)	-	30000	only for internal testing
8.3.3.7(Verification of temperature-rise)	-	25000	only for internal testing
8.3.3.8(Verification of Overload releases)	-	4000	only for internal testing
8.3.3.9(Verification of undervoltage and shunt releases)	-	10000	only for internal testing
8.3.3.10(Verification of main contact position)	-	5000	only for internal testing
8.3.4.3(Verification of operational performance capability)	-	50000	only for internal testing
8.3.5.4(Verification of dielectric withstand)	-	30000	only for internal testing
8.3.6.6(Verification of dielectric withstand)	-	30000	only for internal testing
8.3.7.4(Verification of dielectric withstand)	-	30000	only for internal testing
8.3.7.8(Verification of dielectric withstand)	-	30000	only for internal testing
8.3.8.6(Verification of dielectric withstand)	-	30000	only for internal testing
8.3.4.5(Verifiation of temperature-rise)	-	25000	only for internal testing
8.3.6.4(Verification of temperature-rise)	-	25000	only for internal testing
8.3.7.3(Verification of temperature-rise)	-	25000	only for internal testing
8.3.8.7(Verification of temperature-rise)	-	25000	only for internal testing
8.3.4.6(Verification of Overload releases)	-	5000	only for internal testing
8.3.5.2(Verification of Overload releases)	-	5000	only for internal testing
8.3.5.5(Verification of Overload releases)	-	5000	only for internal testing
8.3.6.2(Verification of Overload releases)	-	5000	only for internal testing
8.3.6.7(Verification of Overload releases)	-	5000	only for internal testing
8.3.7.5(Verification of Overload releases)	-	5000	only for internal testing
8.3.7.9(Verification of Overload releases)	-	5000	only for internal testing
8.3.8.2(Verification of Overload releases)	-	5000	only for internal testing
8.3.8.8(Verification of Overload releases)	-	5000	only for internal testing
C.3(verification of dielectric withstand)	-	25000	only for internal testing
C.4(verification of overload releases)	-	5000	only for internal testing
H.2(individual pole short circuit (IIT))	-	95000	only for internal testing
H.3(verification of dielectric withstand)	-	25000	only for internal testing
H.4(verification of overload releases)	-	5000	only for internal testing
8.3.8.5(Verification of operational performance capability)	-	50000	only for internal testing
8.4.2(Mechanical operation tests)	-	15000	only for internal testing
8.4.3(Verification of the calibration of overcurrent releases)	-	10000	only for internal testing
8.4.4(Verification of the operation of undervoltage and shunt releases)	-	10000	only for internal testing
8.4.5(Additional tests for CBRs)	-	0	Test is not available
8.4.6(Dielectric tests)	-	60000	only for internal testing
8.4.7(Test for the verifiacation of clearances less than those corresponding to case A of Table 13 of IEC 60947-1:2007)	-	3000	only for internal testing
8.3.4.4(Verification of dielectric withstand)	-	28000	only for internal testing
B.8.2(Operating characteristics)	-	10000	only for internal testing
B.8.3(Dielectric Properties)	-	60000	only for internal testing
B.8.4(Operation of the test device at the limits of rated voltage)	-	10000	only for internal testing
B.8.5(Limiting value of the non-operating current under over-current conditions)	-	0	Test is not available
B.8.6(Resistance against unwanted tripping due to surge currents resulting from impulse voltage)	-	0	Test is not available
B.8.7(Behavior in the case of an earth fault current comprising a d.c. component)	-	0	Test is not available
B.8.8(Behavior in the case of failure of line voltage for CBRs classified under B.3.1.2.1)	-	0	Test is not available
B.8.9(Behavior in the case of failure of line voltage for CBRs classified under B.3.1.2.2)	-	0	Test is not available
7.3 Annexure J Table J.1(Electrostatic discharges)	-	0	Test is not available
7.3 Annexure J Table J.1("Radiated radio-frequency electromagnetic fields")	-	0	Test is not available
7.3 Annexure J Table J.1("Electrical fast transients/bursts")	-	0	Test is not available
7.3 Annexure J Table J.1("Radiated radio-frequency electromagnetic fields")	-	0	Test is not available
7.3 Annexure J Table J.1(Surges)	-	0	Test is not available
7.3 Annexure J Table J.1("Conducted disturbances induced by radio frequency fields")	-	0	Test is not available
7.3 Annexure J Table J.1("Power frequency magnetic fields")	-	0	Test is not available
7.3 Annexure J Table J.1("Voltage dips and interruptions")	-	0	Test is not available
7.3 Annexure J Table J.3("Conducted RF disturbances 150 kHz to 30 MHz")	-	0	Test is not available
7.3 Annexure J Table J.3("Radiated RF disturbances 30 MHz to 1 000 MHz")	-	0	Test is not available
8.3.4.1(General)	-	10000	Test sequence II ( Pre & post tests are available Except short circuit )- Only for internal testing )
8.3.4.2(Test of service short circuit breaking capacity)	-	10000	short circuit test is not available (under exclusion )
8.3.5.1(General)	-	10000	Test sequence III ( Pre & post tests are available Except short circuit )- Only for internal testing)
8.3.5.3(rated short circuit breaking capacity (sequence III))	-	0	short circuit test is not available (under exclusion )
8.3.6.1(General)	-	10000	Test sequence IV ( Pre & post tests are available Except short circuit )- Only for internal testing
8.3.6.3(rated short circuit withstand current (sequence IV))	-	0	short circuit test is not available (under exclusion)
8.3.6.5(Short-circuit breaking capacity at maximum short-time withstand current)	-	0	short circuit test is not available (under exclusion)
8.3.7.1(General)	-	10000	Test sequence V ( Pre & post tests are available Except short circuit )- Only for internal testing
8.3.7.2((stage 1) short circuit at the selectivity limit current (sequence V))	-	0	short circuit test is not available (under exclusion)
8.3.7.6((stage 2) short circuit at 1.1 time the take-over current (sequence V))	-	0	short circuit test is not available (under exclusion)
8.3.7.7((stage 2) short circuit at rated ultimate short circuit breaking capacity (sequence V))	-	0	short circuit test is not available (under exclusion)
8.3.8.1(General)	-	10000	Test sequence VI ( Pre & post tests are available Except short circuit )- Only for internal testing
8.3.8.3(rated short time withstand current (sequence VI))	-	0	short circuit test is not available (under exclusion)
8.3.8.4(rated service short circuit breaking capacity (sequence VI))	-	0	short circuit test is not available (under exclusion)
Cl.8.5 (Annex Q of IS/IEC 60947-1)(Special tests)	-	0	only Damp heat test for internal testing
Annex G(Power loss)	-	0	only for internal testing Note- Annex G test (Power loss) are not available
Annex L(Circuit-breakers not fulfilling the requirements for overcurrent protection)	-	0	only for internal testing Note- Annex L test (Circuit-breakers not fulfilling the requirements for overcurrent protection) are not available
Annex M(Modular residual current devices (without integral current breaking device))	-	0	only for internal testing Note- Annex M test (Modular residual current devices (without integral current breaking device) are not available
Annex N(Electromagnetic compatibility (EMC))	-	0	only for internal testing Note- Annex N test (Modular residual current devices (without integral current breaking device) are not available
Annex O(Electromagnetic compatibility (EMC))	-	0	only for internal testing Note- Annex O test (Electromagnetic compatibility (EMC) are not available
Annex P(DC circuit-breakers for use in photovoltaic (PV) applications)	-	0	only for internal testing Note- Annex P test (DC circuit-breakers for use in photovoltaic (PV) applications) are not available
Annex R(Circuit-breakers incorporating residual current protection with automatic re-closing functions)	-	0	only for internal testing Note- Annex R test (Circuit-breakers incorporating residual current protection with automatic re-closing functions) are not available
8.3.6.1(General)	-	10000	Test sequence IV ( Pre & post tests are available Except short circuit )- Only for internal testing
8.3.7.2(Short-circuit at the selectivity limit current)	-	0	short circuit test is not available (under exclusion)
8.3.5.3(Rated ultimate short-circuit breaking capacity)	-	0	short circuit test is not available (under exclusion)
8.3.6.3(Rated short-time withstand current)	-	0	short circuit test is not available (under exclusion)
8.3.7.6(Short-circuit at 1,1 times take-over current)	-	0	short circuit test is not available (under exclusion)
8.3.7.7(Short-circuit at ultimate short-circuit breaking capacity)	-	0	short circuit test is not available (under exclusion)
8.3.8.3(Rated short-time withstand current)	-	0	short circuit test is not available (under exclusion)
8.3.4.2(rated short circuit breaking capacity (sequence II))	-	0	short circuit test is not available (under exclusion)
8.3.8.1(General)	-	10000	Test sequence VI ( Pre & post tests are available Except short circuit )- Only for internal testing
8.3.8.2(verification of overload releases (sequence VI))	-	4000	short circuit test is not available (under exclusion)
8.3.4.1(General)	-	10000	Test sequence II ( Pre & post tests are available Except short circuit )- Only for internal testing )
C.2(individual pole short circuit breaking capacity (Isu))	-	0	short circuit test is not available (under exclusion)
8.3.9(Critical d.c. load current test)	-	0	Critical d.c. load current test -under exclusion
8.3.8.5(verification of operational performance capability (sequence VI))	-	0	only for internal testing
8.3.8.6(verification of dielectric withstand (sequence VI))	-	28000	only for internal testing
8.3.4.3(verification of operational performance capability (sequence II))	-	50000	only for internal testing
8.3.4.4(verification of dielectric withstand (sequnce II))	-	28000	only for internal testing
8.3.6.2(verification of overload releases (sequence IV))	-	4000	only for internal testing
8.3.6.4(verification of temperature-rise (sequence IV))	-	25000	only for internal testing
8.3.6.5(short circuit breaking capacity at maximum short time withstand current (sequence IV))	-	0	short circuit test is not available (under exclusion)
8.3.6.6(verification of dielectric withstand (sequence IV))	-	28000	only for internal testing
8.3.6.7(verification of overload releases (sequence IV))	-	4000	only for internal testing
8.3.7.1(General)	-	10000	Test sequence V ( Pre & post tests are available Except short circuit )- Only for internal testing
8.3.7.3((stage 1) verification of temperature-rise (sequence V))	-	0	short circuit test is not available (under exclusion)
8.3.7.4((stage 1) verification of dielectric withstand (sequence V))	-	28000	only for internal testing
8.3.7.5((stage 2) verification of overload releases (sequence V))	-	4000	only for internal testing
8.3.7.8((stage 2) verification of dielectric withstand (sequence V))	-	28000	only for internal testing
8.3.7.9((stage 2) verification of overload releases (sequence V))	-	4000	only for internal testing
8.3.8.7(verification of temperature-rise (sequence VI))	-	25000	only for internal testing
8.3.8.8(verification of overload releases (sequence VI))	-	4000	only for internal testing
8.3.5.5(verification of overload releases (sequence III))	-	4000	only for internal testing
8.3.5.4(verification of dielectric withstand (sequnce III))	-	28000	only for internal testing
8.3.5.1(General)	-	10000	Test sequence V ( Pre & post tests are available Except short circuit )- Only for internal testing
8.3.5.2(verification of overload releases (sequence III))	-	4000	only for internal testing
8.3.4.5(verification of temperature-rise (sequence II))	-	25000	only for internal testing
8.3.4.6(verification of overload releases (sequence II))	-	4000	only for internal testing
8.3.8.4(Rated service short-circuit breaking capacity*)	-	0	short circuit test is not available (under exclusion)

05 Jun, 2028

-
Exclusion: 8.3.8.4 (rated service short circuit breaking capacity (sequence VI)), 8.3.4.3 (verification of operational performance capability (sequence II)), 8.3.4.1 (General), 8.3.8.4 (Rated service short-circuit breaking capacity*), 8.3.7.7 (Short-circuit at ultimate short-circuit breaking capacity), 8.3.8.3 (rated short time withstand current (sequence VI)), 8.3.7.6 ((stage 2) short circuit at 1.1 time the take-over current (sequence V)), 8.3.8.3 (rated short time withstand current (sequence VI)), 8.3.6.3 (rated short circuit withstand current (sequence IV)), 8.3.7.6 ((stage 2) short circuit at 1.1 time the take-over current (sequence V)), 8.3.6.3 (rated short circuit withstand current (sequence IV)), 8.3.5.3 (rated short circuit breaking capacity (sequence III)), 8.3.7.2 ((stage 1) short circuit at the selectivity limit current (sequence V)), 8.3.5.3 (Rated ultimate short-circuit breaking capacity), Annex N (Electromagnetic compatibility (EMC)), Annex O (Electromagnetic compatibility (EMC)), 7.3 Annexure J Table J.1 (Electrostatic discharges), 8.3.9 (Critical d.c. load current test), Cl.8.5 (Annex Q of IS/IEC 60947-1) (Special tests)

8756

Bombay Textiles Research Association (BTRA), Mumbai

7130206

IS 17373 (2020)

Geosynthetics â€“ Geogrids used in reinforced soil retaining structures â€“ Specification

321545 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
1("Ultimate tensile strength- (MD/CD) IS- 16635 60/20 80/30 100/30 120/30 150/30 180/30 200/30 250/30 300/30 350/30 400/30")	-	3585	-
1("Elongation at designated load- IS 16635 MD CD")	-	0	COVERED IN ULTIMATE TENSILE STRENGTH
1("UV resistance, strength retained after 500 h exposure- IS 13162 (part-2)")	-	52000	-
1(Chemical resistance, strength retained after 72 h immersion- IS 17363)	-	30000	-
1(Width)	-	500	-
1(Roll Length)	-	500	-
2("Ultimate tensile strength - IS 16635 MD/CD 30/5 40/5 50/5 60/5 70/5 80/5 90/5 100/5 120/5 120/5 150/5 175/5 200/5")	-	0	-
2("Elongation at designated load - IS 16635 MD and CD")	-	0	COVERED IN ULTIMATE TENSILE STRENGTH
2("UV resistance, strength retained after 500 h exposure- IS 13162 (part-2)")	-	0	-
2(Chemical resistance, strength retained after 72 h immersion- IS 17363)	-	0	-
2(Width)	-	0	-
2(Roll Length)	-	0	-
3("Ultimate tensile strength - IS 16635 MD/CD 50 100 150 200 250 300 350 400 500 600 700 800 900 1000 1100 1200 1300")	-	0	-
3("Elongation at designated load - IS 16635 MD and CD")	-	0	COVERED IN ULTIMATE TENSILE STRENGTH
3("UV resistance, strength retained after 500 h exposure- IS 13162 (part-2)")	-	0	-
3(Chemical resistance, strength retained after 72 h immersion- IS 17363)	-	0	-
3(Width)	-	0	-
3(Roll Length)	-	0	-
Clause 6.2, Table 1, 2 and 3, SI. No. (i)(Ultimate Tensile Strength,)	-	0	-
Clause 6.2, Table 1, 2 and 3, SI. No. (ii)(Elongation at Designated Load)	-	0	COVERED IN ULTIMATE TENSILE STRENGTH
Clause 6.2, Table 1, 2 and 3, SI. No. (iii)(UV resistance, strength retained after 500 h exposure)	-	0	-
Clause 6.2, Table 1, 2 and 3, SI. No. (iv)(Chemical resistance, strength retained after 72 h immersion)	-	0	-
Clause 6.2, Table 1, 2 and 3, SI. No. (v)(Width)	-	0	-
Clause 6.2, Table 1, 2 and 3, SI. No. (vi)(Roll length)	-	0	-
Clause No. 9.1(Geostrip identification)	-	3260	-
CL 3.2(Aperature Size)	-	500	-
6.2 Table 1("Chemical resistance, strength retained after 72 h immersion (percent)")	-	0	-
CL 6.3.3(Resistance to hydrolysis)	-	10000	-
6.2 Table 1(UV resistance strength retained after 500h exposure (Percent))	-	0	-
CL 6.3.2(Installation damage)	-	150000	-
CL 6.3.2(Resistance to oxidation)	-	36000	-
CL 6.3.2(Resistance to Micro organisms)	-	25000	-
CL 5.1(Carbon black content)	-	1200	-
CL 5.2(Number Average Molecular weight)	-	5500	-
CL 5.2(CEG content)	-	3000	-
6.2 Table 1(Ultimate Tensile Strength kN/m (MD))	-	0	-
6.2 Table 1(Ultimate Tensile Strength kN/m (CD))	-	0	COVERED IN ULTIMATE TENSILE STRENGTH
6.2 Table 1(Elongation at designated load (Percentage))	-	0	COVERED IN ULTIMATE TENSILE STRENGTH
6.2 Table 1(Elongation at designated load (Percentage))	-	0	COVERED IN ULTIMATE TENSILE STRENGTH
6.2 Table 1(Width (m))	-	0	-
6.2 Table 1(Roll length (m))	-	0	-
CL 5.1(Identification of material)	-	0	-
CL 6.1(Geogrid should be Dimensionally stable)	-	500	-
4(TYPES OF GEOGRIDS - a) Type 1 b) Type 2 c) Type 3)	-	0	-
5.1("MATERIALS - Geogrid materials shall be inert to all chemicals naturally found in commonly encountered soils not containing adverse solvents and at ambient temperatures")	-	0	-
5.2("MATERIALS - PET geogrips shall have average molecular weight more than or equal to 25000 g/mol and shall have carboxyl end group content less than 30 mmol/kg")	-	0	-
6.1(REQUIREMENTS FOR GEOGRIDS - Geogrids shall be dimensionally stable and able to retain their geometry under manufacture,transport, and installation)	-	0	-
6.2-Table 1- i)(Requirements of Geogrids - Ultimate tensile strength)	-	0	-
6.2 - Table 1- ii)(Requirements of Geogrids - Elongation at designated load)	-	0	COVERED IN ULTIMATE TENSILE STRENGTH
6.2 - Table 1- iii)(Requirements of Geogrids - UV resistance, strength retained after 500 h exposure)	-	0	-
6.2 - Table 1- iv)(Requirements of Geogrids - Chemical resistance, strength retained after 72 h immersion)	-	0	-
6.2 - Table 1- v)(Requirements of Geogrids - Width)	-	0	-
6.2 - Table 1- vi)(Requirements of Geogrids - Length)	-	0	-
6.2 - Table 1- i)(Requirements of Geogrids - Ultimate tensile strength)	-	0	-
6.2-Table 2- ii)(Requirements of Geogrids - Elongation at designated load)	-	0	COVERED IN ULTIMATE TENSILE STRENGTH
6.2 - Table 2- iii)(Requirements of Geogrids - UV resistance, strength retained after 500 h exposure)	-	0	-
6.2 - Table 2- iv)(Requirements of Geogrids - Chemical resistance, strength retained after 72 h immersion)	-	0	-
6.2 - Table 2- v)(Requirements of Geogrids - Width)	-	0	-
6.2 - Table 2- vi)(Requirements of Geogrids - Length)	-	0	-
6.3.1(Reduction factor for installation damage shall be determined based on actual installation damage test)	-	0	-
6.3.2(Reduction factor for durability is dependent on susceptibility of geogrid to attach by chemicals, thermal oxidation, hydrolysis, environmental stress cracking and micro-organisms)	-	0	COVERED
1("Ultimate tensile strength- (MD/CD) IS- 16635 60/20 80/30 100/30 120/30 150/30 180/30 200/30 250/30 300/30 350/30 400/30")	-	0	-
1("Elongation at designated load- IS 16635 MD CD")	-	0	-
1("UV resistance, strength retained after 500 h exposure- IS 13162 (part-2)")	-	0	-
1(Chemical resistance, strength retained after 72 h immersion- IS 17363)	-	0	-
1(Width)	-	0	-
1(Roll Length)	-	0	-
2("Ultimate tensile strength - IS 16635 MD/CD 30/5 40/5 50/5 60/5 70/5 80/5 90/5 100/5 120/5 120/5 150/5 175/5 200/5")	-	0	-
2("Elongation at designated load - IS 16635 MD and CD")	-	0	-
2("UV resistance, strength retained after 500 h exposure- IS 13162 (part-2)")	-	0	-
2(Chemical resistance, strength retained after 72 h immersion- IS 17363)	-	0	-
2(Width)	-	0	-
2(Roll Length)	-	0	-
3("Ultimate tensile strength - IS 16635 MD/CD 50 100 150 200 250 300 350 400 500 600 700 800 900 1000 1100 1200 1300")	-	0	-
3("Elongation at designated load - IS 16635 MD and CD")	-	0	-
3("UV resistance, strength retained after 500 h exposure- IS 13162 (part-2)")	-	0	-
3(Chemical resistance, strength retained after 72 h immersion- IS 17363)	-	0	-
3(Width)	-	0	-
3(Roll Length)	-	0	-
Clause 6.2, Table 1, 2 and 3, SI. No. (i)(Ultimate Tensile Strength,)	-	0	-
Clause 6.2, Table 1, 2 and 3, SI. No. (ii)(Elongation at Designated Load)	-	0	-
Clause 6.2, Table 1, 2 and 3, SI. No. (iii)(UV resistance, strength retained after 500 h exposure)	-	0	-
Clause 6.2, Table 1, 2 and 3, SI. No. (iv)(Chemical resistance, strength retained after 72 h immersion)	-	0	-
Clause 6.2, Table 1, 2 and 3, SI. No. (v)(Width)	-	0	-
Clause 6.2, Table 1, 2 and 3, SI. No. (vi)(Roll length)	-	0	-
Clause No. 9.1(Geostrip identification)	-	0	-
CL 3.2(Aperature Size)	-	0	-
6.2 Table 1("Chemical resistance, strength retained after 72 h immersion (percent)")	-	0	-
CL 6.3.3(Resistance to hydrolysis)	-	0	-
6.2 Table 1(UV resistance strength retained after 500h exposure (Percent))	-	0	-
CL 6.3.2(Installation damage)	-	0	-
CL 6.3.2(Resistance to oxidation)	-	0	-
CL 6.3.2(Resistance to Micro organisms)	-	0	-
CL 5.1(Carbon black content)	-	0	-
CL 5.2(Number Average Molecular weight)	-	0	-
CL 5.2(CEG content)	-	0	-
6.2 Table 1(Ultimate Tensile Strength kN/m (MD))	-	0	-
6.2 Table 1(Ultimate Tensile Strength kN/m (CD))	-	0	-
6.2 Table 1(Elongation at designated load (Percentage))	-	0	-
6.2 Table 1(Elongation at designated load (Percentage))	-	0	-
6.2 Table 1(Width (m))	-	0	-
6.2 Table 1(Roll length (m))	-	0	-
CL 5.1(Identification of material)	-	0	-
CL 6.1(Geogrid should be Dimensionally stable)	-	0	-
4(TYPES OF GEOGRIDS - a) Type 1 b) Type 2 c) Type 3)	-	0	-
5.1("MATERIALS - Geogrid materials shall be inert to all chemicals naturally found in commonly encountered soils not containing adverse solvents and at ambient temperatures")	-	0	-
5.2("MATERIALS - PET geogrips shall have average molecular weight more than or equal to 25000 g/mol and shall have carboxyl end group content less than 30 mmol/kg")	-	0	-
6.1(REQUIREMENTS FOR GEOGRIDS - Geogrids shall be dimensionally stable and able to retain their geometry under manufacture,transport, and installation)	-	0	-
6.2-Table 1- i)(Requirements of Geogrids - Ultimate tensile strength)	-	0	-
6.2 - Table 1- ii)(Requirements of Geogrids - Elongation at designated load)	-	0	-
6.2 - Table 1- iii)(Requirements of Geogrids - UV resistance, strength retained after 500 h exposure)	-	0	-
6.2 - Table 1- iv)(Requirements of Geogrids - Chemical resistance, strength retained after 72 h immersion)	-	0	-
6.2 - Table 1- v)(Requirements of Geogrids - Width)	-	0	-
6.2 - Table 1- vi)(Requirements of Geogrids - Length)	-	0	-
6.2 - Table 1- i)(Requirements of Geogrids - Ultimate tensile strength)	-	0	-
6.2-Table 2- ii)(Requirements of Geogrids - Elongation at designated load)	-	0	-
6.2 - Table 2- iii)(Requirements of Geogrids - UV resistance, strength retained after 500 h exposure)	-	0	-
6.2 - Table 2- iv)(Requirements of Geogrids - Chemical resistance, strength retained after 72 h immersion)	-	0	-
6.2 - Table 2- v)(Requirements of Geogrids - Width)	-	0	-
6.2 - Table 2- vi)(Requirements of Geogrids - Length)	-	0	-
6.3.1(Reduction factor for installation damage shall be determined based on actual installation damage test)	-	0	-
6.3.2(Reduction factor for durability is dependent on susceptibility of geogrid to attach by chemicals, thermal oxidation, hydrolysis, environmental stress cracking and micro-organisms)	-	0	-
1("Ultimate tensile strength- (MD/CD) IS- 16635 60/20 80/30 100/30 120/30 150/30 180/30 200/30 250/30 300/30 350/30 400/30")	-	0	-
1("Elongation at designated load- IS 16635 MD CD")	-	0	-
1("UV resistance, strength retained after 500 h exposure- IS 13162 (part-2)")	-	0	-
1(Chemical resistance, strength retained after 72 h immersion- IS 17363)	-	0	-
1(Width)	-	0	-
1(Roll Length)	-	0	-
2("Ultimate tensile strength - IS 16635 MD/CD 30/5 40/5 50/5 60/5 70/5 80/5 90/5 100/5 120/5 120/5 150/5 175/5 200/5")	-	0	-
2("Elongation at designated load - IS 16635 MD and CD")	-	0	-
2("UV resistance, strength retained after 500 h exposure- IS 13162 (part-2)")	-	0	-
2(Chemical resistance, strength retained after 72 h immersion- IS 17363)	-	0	-
2(Width)	-	0	-
2(Roll Length)	-	0	-
3("Ultimate tensile strength - IS 16635 MD/CD 50 100 150 200 250 300 350 400 500 600 700 800 900 1000 1100 1200 1300")	-	0	-
3("Elongation at designated load - IS 16635 MD and CD")	-	0	-
3("UV resistance, strength retained after 500 h exposure- IS 13162 (part-2)")	-	0	-
3(Chemical resistance, strength retained after 72 h immersion- IS 17363)	-	0	-
3(Width)	-	0	-
3(Roll Length)	-	0	-
Clause 6.2, Table 1, 2 and 3, SI. No. (i)(Ultimate Tensile Strength,)	-	0	-
Clause 6.2, Table 1, 2 and 3, SI. No. (ii)(Elongation at Designated Load)	-	0	-
Clause 6.2, Table 1, 2 and 3, SI. No. (iii)(UV resistance, strength retained after 500 h exposure)	-	0	-
Clause 6.2, Table 1, 2 and 3, SI. No. (iv)(Chemical resistance, strength retained after 72 h immersion)	-	0	-
Clause 6.2, Table 1, 2 and 3, SI. No. (v)(Width)	-	0	-
Clause 6.2, Table 1, 2 and 3, SI. No. (vi)(Roll length)	-	0	-
Clause No. 9.1(Geostrip identification)	-	0	-
CL 3.2(Aperature Size)	-	0	-
6.2 Table 1("Chemical resistance, strength retained after 72 h immersion (percent)")	-	0	-
CL 6.3.3(Resistance to hydrolysis)	-	0	-
6.2 Table 1(UV resistance strength retained after 500h exposure (Percent))	-	0	-
CL 6.3.2(Installation damage)	-	0	-
CL 6.3.2(Resistance to oxidation)	-	0	-
CL 6.3.2(Resistance to Micro organisms)	-	0	-
CL 5.1(Carbon black content)	-	0	-
CL 5.2(Number Average Molecular weight)	-	0	-
CL 5.2(CEG content)	-	0	-
6.2 Table 1(Ultimate Tensile Strength kN/m (MD))	-	0	-
6.2 Table 1(Ultimate Tensile Strength kN/m (CD))	-	0	-
6.2 Table 1(Elongation at designated load (Percentage))	-	0	-
6.2 Table 1(Elongation at designated load (Percentage))	-	0	-
6.2 Table 1(Width (m))	-	0	-
6.2 Table 1(Roll length (m))	-	0	-
CL 5.1(Identification of material)	-	0	-
CL 6.1(Geogrid should be Dimensionally stable)	-	0	-
4(TYPES OF GEOGRIDS - a) Type 1 b) Type 2 c) Type 3)	-	0	-
5.1("MATERIALS - Geogrid materials shall be inert to all chemicals naturally found in commonly encountered soils not containing adverse solvents and at ambient temperatures")	-	0	-
5.2("MATERIALS - PET geogrips shall have average molecular weight more than or equal to 25000 g/mol and shall have carboxyl end group content less than 30 mmol/kg")	-	0	-
6.1(REQUIREMENTS FOR GEOGRIDS - Geogrids shall be dimensionally stable and able to retain their geometry under manufacture,transport, and installation)	-	0	-
6.2-Table 1- i)(Requirements of Geogrids - Ultimate tensile strength)	-	0	-
6.2 - Table 1- ii)(Requirements of Geogrids - Elongation at designated load)	-	0	-
6.2 - Table 1- iii)(Requirements of Geogrids - UV resistance, strength retained after 500 h exposure)	-	0	-
6.2 - Table 1- iv)(Requirements of Geogrids - Chemical resistance, strength retained after 72 h immersion)	-	0	-
6.2 - Table 1- v)(Requirements of Geogrids - Width)	-	0	-
6.2 - Table 1- vi)(Requirements of Geogrids - Length)	-	0	-
6.2 - Table 1- i)(Requirements of Geogrids - Ultimate tensile strength)	-	0	-
6.2-Table 2- ii)(Requirements of Geogrids - Elongation at designated load)	-	0	-
6.2 - Table 2- iii)(Requirements of Geogrids - UV resistance, strength retained after 500 h exposure)	-	0	-
6.2 - Table 2- iv)(Requirements of Geogrids - Chemical resistance, strength retained after 72 h immersion)	-	0	-
6.2 - Table 2- v)(Requirements of Geogrids - Width)	-	0	-
6.2 - Table 2- vi)(Requirements of Geogrids - Length)	-	0	-
6.3.1(Reduction factor for installation damage shall be determined based on actual installation damage test)	-	0	-
6.3.2(Reduction factor for durability is dependent on susceptibility of geogrid to attach by chemicals, thermal oxidation, hydrolysis, environmental stress cracking and micro-organisms)	-	0	-

-
-

8757

BIS, Bengaluru Branch Laboratory (BNBL)

None

IS 261 (2023)

COPPER SULPHATE SPECIFICATION

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Description ( IS 261 : 2023))	-
4.2Table 1 (i) (Copper ( IS 261 : 2023))	-
4.2 Table 1 (ii) (Matter insoluble in water ( IS 261 : 2023))	-
4.2 Table 1 (iii) (Soluble iron and aluminium compounds (as Fe) ( IS 261 : 2023))	-
4.2 Table 1 (iv) (pH value ( IS 261 : 2023))	-
4.2 Table 1 (v) (Chloride (as Cl) ( IS 261 : 2023))	-
4.2 Table 1 (vi) (Arsenic (as As₂O₃) ( IS 261 : 2023))	-
4.2 Table 1 (vii) (Lead and zinc ( IS 261 : 2023))	-

-
Complete test facility available for Technical grade

8758

ACCURATE TEST SOLUTIONS LLP (F21), NOIDA

8141226

IS 302 : Part 2 : Sec 7 (2010)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 7 domestic electric clothes washing machines (First Revision)

43000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
32(Radiation ,Toxicity and similar hazards)	-	500	5% discount for BIS
31(Resistance to Rusting)	-	500	5% discount for BIS
30(Resistance to Heat & Fire)	-	5000	5% discount for BIS
29(Clearances, Creepage Distances & Solid Insulation)	-	1000	5% discount for BIS
28(Screws & Connections)	-	500	5% discount for BIS
27(Provision For Earthing)	-	500	5% discount for BIS
26(Terminals For External Conductors)	-	500	5% discount for BIS
25(Supply Connection & External Flexible Cords)	-	500	5% discount for BIS
23(Internal wiring)	-	500	5% discount for BIS
22(Construction)	-	500	5% discount for BIS
21(Mechanical strength)	-	500	5% discount for BIS
20(Stability & Mechanical Hazards)	-	500	5% discount for BIS
19(Abnormal Operation)	-	500	5% discount for BIS
18(Endurance)	-	5000	5% discount for BIS
17(Overload Protection/ Overload Protection of Transformers & Associated Circuits)	-	1000	5% discount for BIS
16(Leakage Current and Electric Strength)	-	1000	5% discount for BIS
15(Moisture Resistance)	-	5000	5% discount for BIS
14(Transient Over Voltage)	-	5000	5% discount for BIS
13(Leakage Current and Electric Strength at Operating Temperature)	-	1000	5% discount for BIS
11(Temperature Rise/ Heating)	-	5000	5% discount for BIS
10(Power Input & Current )	-	5000	5% discount for BIS
9(Starting of Motor operated appliances)	-	500	5% discount for BIS
8(Protection against access to live parts)	-	500	5% discount for BIS
7(Marking)	-	500	5% discount for BIS
6(Classification)	-	500	5% discount for BIS
4(GENERAL REQUIREMENTS)	-	500	5% discount for BIS
5(GENERAL CONDITIONS FOR THE TESTS)	-	500	5% discount for BIS
32(Radiation ,Toxicity and similar hazards)	-	-	-
31(Resistance to Rusting)	-	-	-
30(Resistance to Heat & Fire)	-	-	-
29(Clearances, Creepage Distances & Solid Insulation)	-	-	-
28(Screws & Connections)	-	-	-
27(Provision For Earthing)	-	-	-
26(Terminals For External Conductors)	-	-	-
25(Supply Connection & External Flexible Cords)	-	-	-
23(Internal wiring)	-	-	-
22(Construction)	-	-	-
21(Mechanical strength)	-	-	-
20(Stability & Mechanical Hazards)	-	-	-
19(Abnormal Operation)	-	-	-
18(Endurance)	-	-	-
17(Overload Protection/ Overload Protection of Transformers & Associated Circuits)	-	-	-
16(Leakage Current and Electric Strength)	-	-	-
15(Moisture Resistance)	-	-	-
14(Transient Over Voltage)	-	-	-
13(Leakage Current and Electric Strength at Operating Temperature)	-	-	-
11(Temperature Rise/ Heating)	-	-	-
10(Power Input & Current )	-	-	-
9(Starting of Motor operated appliances)	-	-	-
8(Protection against access to live parts)	-	-	-
7(Marking)	-	-	-
6(Classification)	-	-	-
4(GENERAL REQUIREMENTS)	-	-	-
5(GENERAL CONDITIONS FOR THE TESTS)	-	-	-

04 Jul, 2027

-
Included w.e.f.05.11.2024

8759

BIS, Eastern Regional Laboratory (ERL)

None

IS 16651 (2017)

High Strength Deformed Stainless Steel Bars and Wires for Concrete Reinforcement - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8.2 / Table 5 (Physical Properties)	-
Cl 8.2 / Table 5 (Physical Properties)	-
Cl 8.2 / Table 5 (Physical Properties)	-
6.2 (The values for the nominal cross-sectional area)	-
Cl 8.6 (Charpy Impact Test)	-
9.3 (Bend Test)	-
9.4 (Rebend Test)	-
Cl 5.2 (Deformations and Surface Characteristics)	-
Clause-4.3.1, Table- 1 (CARBON)	-
Clause-4.3.1, Table- 1 (PHOSPHURS)	-
Clause-4.3.1, Table- 1 (MANGANESE)	-
Clause-4.3.1, Table- 1 (NITROGEN)	-
Clause-4.3.1, Table- 1 (SILICON)	-
Clause-4.3.1, Table- 1 (CHROMIUM)	-
Clause-4.3.1, Table- 1 (COPPER)	-
Clause-4.3.1, Table- 1 (MOLYBDENUM)	-
Clause-4.3.1, Table- 1 (NICKEL)	-

-
Excluding Fatigue test, C(<0.05 %), S, Mo(>1.5%)

8760

Atmy Analytical Labs Pvt. Ltd., Faridabad

8167506

IS 17569 (2021)

Insulated Containers for Food Storage — Specification

ALL

33900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Manufacture and Workmanship)	-	33900	-
5.3(Manufacture and Workmanship)	-	33900	-
7.1(Material)	-	33900	-
7.1.2(Thickness)	-	33900	-
7.1.2.1(Requirements and Tests(Material) – Outer Protective Case and Accessories – Lead)	-	33900	-
7.1.2.1(Requirements and Tests(Material) – Outer Protective Case and Accessories – Cadmium)	-	33900	-
7.1.2.8(Bisphenol A(BPA))	-	33900	-
7.3(Capacity)	-	33900	-
7.4(Heat Retention Capability)	-	33900	-
7.5(Cold Retention Capability)	-	33900	-
7.6.1(Drop Impact Test)	-	33900	-
7.6.2(Pendulum Impact Test)	-	33900	-
7.7(Fixing Strength of the Handle)	-	33900	-
7.8(Test for Strength of Shoulder Strap)	-	33900	-
7.9(Leakage Test)	-	33900	-
7.10(Joint Leak Test)	-	33900	-
7.11(Staining Test)	-	33900	-
7.12("Check for PUF (Polyurethane Foam) or any Other Similar Thermal Insulation Material ")	-	33900	-
7.13.1(Length of the Shoulder Strap)	-	33900	-
7.13.2(Stability of Insulated Container)	-	33900	-
7.13.3(Cleaning)	-	33900	-
7.14(Seepage Test)	-	33900	-
9.1(Marking)	-	33900	-
9.2(BIS certification marking)	-	33900	-
10(Packaging)	-	33900	-
CLAUSE 5.2(Welding Defects)	-	33900	-
CLAUSE 7.1(Materials)	-	33900	-
CLAUSE 7.1.2.2(Thickness of plastic)	-	33900	-
"CLAUSE 7.1.2.1 "(Minimum Thickness of Outer Container)	-	33900	-
"CLAUSE 7.1.2.1 "(Coating Thickness)	-	33900	-
"CLAUSE 7.1.2.1 "(Salt Water Corrosion Test)	-	33900	-
CLAUSE 7.1.2.1(Adhesion Test)	-	33900	-
CLAUSE 7.1.2.1(Lead Limit)	-	33900	-
CLAUSE 7.1.2.1(Cadmium Limit)	-	33900	-
CLAUSE 7.1.2.3(Outer container or lid - thickness)	-	33900	-
CLAUSE 7.3(Capacity)	-	33900	-
CLAUSE 7.4(Heat Retention Capability)	-	33900	-
CLAUSE 7.5(Cold Retention Capability)	-	33900	-
CLAUSE 7.6.1(Drop Impact)	-	33900	-
CLAUSE 7.6.2(Pendulum Impact)	-	33900	-
CLAUSE 7.7(Fixing Strength of Handle)	-	33900	-
CLAUSE 7.8(Test for Strength of Shoulder Strap)	-	33500	-
CLAUSE 7.9(Leakage Test)	-	33900	-
CLAUSE 7.10(Joint Leak Test)	-	33900	-
CLAUSE 7.11(Staining Test)	-	33900	-
CLAUSE 7.12(Checking of PUF insulation)	-	33900	-
CLAUSE 7.13.1(Length of the Shoulder Strap)	-	33900	-
CLAUSE 7.13.2(Stability of Flask)	-	33900	-
CLAUSE 7.1.1(Material - inner container)	-	33900	-
5(Manufacture and Workmanship)	-	33900	-
5.3(Manufacture and Workmanship)	-	33900	-
7.1(Material)	-	33900	-
7.1.2(Thickness)	-	33900	-
7.1.2.1(Requirements and Tests(Material) – Outer Protective Case and Accessories – Lead)	-	33900	-
7.1.2.1(Requirements and Tests(Material) – Outer Protective Case and Accessories – Cadmium)	-	33900	-
7.1.2.8(Bisphenol A(BPA))	-	33900	-
7.3(Capacity)	-	33900	-
7.4(Heat Retention Capability)	-	33900	-
7.5(Cold Retention Capability)	-	33900	-
7.6.1(Drop Impact Test)	-	33900	-
7.6.2(Pendulum Impact Test)	-	33900	-
7.7(Fixing Strength of the Handle)	-	33900	-
7.8(Test for Strength of Shoulder Strap)	-	33900	-
7.9(Leakage Test)	-	33900	-
7.10(Joint Leak Test)	-	33900	-
7.11(Staining Test)	-	33900	-
7.12("Check for PUF (Polyurethane Foam) or any Other Similar Thermal Insulation Material ")	-	33900	-
7.13.1(Length of the Shoulder Strap)	-	33900	-
7.13.2(Stability of Insulated Container)	-	33900	-
7.13.3(Cleaning)	-	33900	-
7.14(Seepage Test)	-	33900	-
9.1(Marking)	-	33900	-
9.2(BIS certification marking)	-	33900	-
10(Packaging)	-	33900	-
CLAUSE 5.2(Welding Defects)	-	33900	-
CLAUSE 7.1(Materials)	-	33900	-
CLAUSE 7.1.2.2(Thickness of plastic)	-	33900	-
"CLAUSE 7.1.2.1 "(Minimum Thickness of Outer Container)	-	33900	-
"CLAUSE 7.1.2.1 "(Coating Thickness)	-	33900	-
"CLAUSE 7.1.2.1 "(Salt Water Corrosion Test)	-	33900	-
CLAUSE 7.1.2.1(Adhesion Test)	-	33900	-
CLAUSE 7.1.2.1(Lead Limit)	-	33900	-
CLAUSE 7.1.2.1(Cadmium Limit)	-	33900	-
CLAUSE 7.1.2.3(Outer container or lid - thickness)	-	33900	-
CLAUSE 7.3(Capacity)	-	33900	-
CLAUSE 7.4(Heat Retention Capability)	-	33900	-
CLAUSE 7.5(Cold Retention Capability)	-	33900	-
CLAUSE 7.6.1(Drop Impact)	-	33900	-
CLAUSE 7.6.2(Pendulum Impact)	-	33900	-
CLAUSE 7.7(Fixing Strength of Handle)	-	33900	-
CLAUSE 7.8(Test for Strength of Shoulder Strap)	-	33900	-
CLAUSE 7.9(Leakage Test)	-	33900	-
CLAUSE 7.10(Joint Leak Test)	-	33900	-
CLAUSE 7.11(Staining Test)	-	33900	-
CLAUSE 7.12(Checking of PUF insulation)	-	33900	-
CLAUSE 7.13.1(Length of the Shoulder Strap)	-	33900	-
CLAUSE 7.13.2(Stability of Flask)	-	33900	-
CLAUSE 7.1.1(Material - inner container)	-	33900	-
5(Manufacture and Workmanship)	-	-	-
5.3(Manufacture and Workmanship)	-	-	-
7.1(Material)	-	-	-
7.1.2(Thickness)	-	-	-
7.1.2.1(Requirements and Tests(Material) – Outer Protective Case and Accessories – Lead)	-	-	-
7.1.2.1(Requirements and Tests(Material) – Outer Protective Case and Accessories – Cadmium)	-	-	-
7.1.2.8(Bisphenol A(BPA))	-	-	-
7.3(Capacity)	-	-	-
7.4(Heat Retention Capability)	-	-	-
7.5(Cold Retention Capability)	-	-	-
7.6.1(Drop Impact Test)	-	-	-
7.6.2(Pendulum Impact Test)	-	-	-
7.7(Fixing Strength of the Handle)	-	-	-
7.8(Test for Strength of Shoulder Strap)	-	-	-
7.9(Leakage Test)	-	-	-
7.10(Joint Leak Test)	-	-	-
7.11(Staining Test)	-	-	-
7.12("Check for PUF (Polyurethane Foam) or any Other Similar Thermal Insulation Material ")	-	-	-
7.13.1(Length of the Shoulder Strap)	-	-	-
7.13.2(Stability of Insulated Container)	-	-	-
7.13.3(Cleaning)	-	-	-
7.14(Seepage Test)	-	-	-
9.1(Marking)	-	-	-
9.2(BIS certification marking)	-	-	-
10(Packaging)	-	-	-
CLAUSE 5.2(Welding Defects)	-	-	-
CLAUSE 7.1(Materials)	-	-	-
CLAUSE 7.1.2.2(Thickness of plastic)	-	-	-
"CLAUSE 7.1.2.1 "(Minimum Thickness of Outer Container)	-	-	-
"CLAUSE 7.1.2.1 "(Coating Thickness)	-	-	-
"CLAUSE 7.1.2.1 "(Salt Water Corrosion Test)	-	-	-
CLAUSE 7.1.2.1(Adhesion Test)	-	-	-
CLAUSE 7.1.2.1(Lead Limit)	-	-	-
CLAUSE 7.1.2.1(Cadmium Limit)	-	-	-
CLAUSE 7.1.2.3(Outer container or lid - thickness)	-	-	-
CLAUSE 7.3(Capacity)	-	-	-
CLAUSE 7.4(Heat Retention Capability)	-	-	-
CLAUSE 7.5(Cold Retention Capability)	-	-	-
CLAUSE 7.6.1(Drop Impact)	-	-	-
CLAUSE 7.6.2(Pendulum Impact)	-	-	-
CLAUSE 7.7(Fixing Strength of Handle)	-	-	-
CLAUSE 7.8(Test for Strength of Shoulder Strap)	-	-	-
CLAUSE 7.9(Leakage Test)	-	-	-
CLAUSE 7.10(Joint Leak Test)	-	-	-
CLAUSE 7.11(Staining Test)	-	-	-
CLAUSE 7.12(Checking of PUF insulation)	-	-	-
CLAUSE 7.13.1(Length of the Shoulder Strap)	-	-	-
CLAUSE 7.13.2(Stability of Flask)	-	-	-
CLAUSE 7.1.1(Material - inner container)	-	-	-

25 Feb, 2027

-
-

Bureau of Indian Standards

The National Standards Body of India

Search by IS Number