BIS - LIMS (Laboratory Information Management System)

Search by IS Number

Reset

12008 Results

S.No.

Lab Name

Osl Code

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

11821

BIS, Northern Regional Laboratory (NRL)

None

IS 398 : Part 5 (1992)

Aluminium conductor for overhead transmission purposes - Specification: Part 5 aluminium conductors - Galvanized steel - Reinforced for extra high voltage (400 KV And Above) (First Revision)

11400 View breakup
Excluding Breaking load on complete conductor, Surface condition test, Corona test and Radio interference test

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7 (elec) (Freedom from defects)	-
13.2 (mech) (Visual Examination)	-
13.3 Table-1 (mech) (Diameter-Aluminium wires)	-
13.3 Table-2 (mech) (Diameter-Galvanized Steel wires)	-
13.5.2 Table 1 (mech) (Breaking Load of Aluminium Wires Before Stranding)	-
13.5.2 Table 2 (mech) (Breaking Load of Steel Wires Before Stranding)	-
13.5.2 Table 1 (mech) (Breaking Load of Aluminium Wires After Stranding)	-
13.5.2 Table 2 (mech) (Breaking Load of Steel Wires After Stranding)	-
13.6.1 (mech) (Ductility by Torsion Test before stranding)	-
13.6.1 (mech) (Ductility by Torsion Test after stranding)	-
13.6.2 (mech) (Ductility by Elongation Test before stranding)	-
13.6.2 (mech) (Ductility by Elongation Test after stranding)	-
13.6.2 (mech) (Ductility by Elongation Test before stranding)	-
13.6.2 (mech) (Ductility by Elongation Test after stranding)	-
13.7.1 (mech) (Wrapping Test Aluminium Wires Before Stranding)	-
13.7.1 (mech) (Wrapping Test Aluminium Wires After Stranding)	-
13.7.2 (mech) (Wrapping Test Galvanized Steel Wires Before Stranding)	-
13.7.2 (mech) (Wrapping Test Galvanized Steel Wires After Stranding)	-
13.8 (elec) (Resistance test-Aluminium wire before Stranding)	-
14.8 (elec) (Resistance test-Aluminium wire after stranding)	-
13.9.2 (chem) (Mass of Zinc coating)	-
13.9.2 (chem) (Uniformity of Zinc coating)	-
13.4 Table-4 (mech) (Lay Ratio- Aluminium Wire Outermost Layer)	-
13.4 Table-4 (mech) (Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-
13.4 Table-4 (mech) (Lay Ratio- Aluminium Wire Innermost Layer of Conductors eith 3 Aluminium Wire Layers)	-
13.4 Table-4 (mech) (Lay Ratio- Steel Core (6 Wire Layer))	-
13.9.2 (chem) (Mass of Zinc coating)	-
13.9.2 (chem) (Uniformity of Zinc coating)	-

-
Except Cl.13.10 surface condition test ,Cl.13.11 corona test ,Cl.13.12 radio interference test for 400 kV & above.,CI.13.5 Stress Strain Test

11822

BIS, Northern Regional Laboratory (NRL)

None

IS 398 : Part 4 (1994)

Aluminium conductors for overhead transmission purposes: Part 4 aluminium alloy stranded conductors (Aluminium - Magnesium - Silicon Type) - Specification (Third Revision)

Rs 825/- upto 7 wires, Rs 1425/- upto 19 wires View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 (Freedom from Defects)	-
7.1 Table-1 (Dimensional measurement of wires)	-
7.2.2 Table-2, Table-4 (Calculated resistance of Stranded Conductor)	-
8.1 (Joints in wires-Conductors Containing Seven Wires)	-
8.2 (Joints in wires-Conductors Containing More Than Seven Wires)	-
9.1 (Stranding)	-
9.2 Table 3 (Lay Ratio of stranded conductors)	-
9.3 (Direction of Lay)	-
9.4 (Multiple layers of wires)	-
11 (Packing and Marking)	-
12.2 Table 1 (Breaking Load Test- Before Stranding)	-
12.2 Table 1 (Breaking Load Test- After Stranding)	-
12.3 Table 1 (Elongation Test- Before Stranding)	-
12.3 Table 1 (Elongation Test- After Stranding)	-
12.4 Table 1 (Resistance of Aluminium wire)	-

-
Test facility is complete

11823

BIS, Northern Regional Laboratory (NRL)

None

IS 1673 (1984)

Spectfication for mild steel wire, cold heading quality (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1 (i)Ultimate Tensile Strength,)	-
7.2 (ii) Reverse Torsion Test)	-
8 ( DIMENSIONS AND TOLERANCES)	-
6 (FREEDOM FROM DEFECTS)	-

-
Except aluminium killed

11824

BIS, Southern Regional Laboratory (SRL)

None

IS 336 (1973)

Specification for ether

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl no .3.1 (Description)	-
Cl no .3.2 (Odour and Taste )	-
Cl No. 3.2.1 (Ether , anaesthetic)	-
Cl no .3.3.1 (Composition )	-
Cl no .3.3.2 (Composition )	-
Cl no .3.4 (Solubility )	-
Cl no .3.5 [ Table 1, Sl no.(ii) ] Appendix A 3 (Peroxides )	-
Cl no .3.5 [ Table 1, Sl no.(iv) ] Appendix A 5 (Residue on Evaporation )	-
Cl no .3.5 [ Table 1, Sl no.(v) ] Appendix A 6 (Methyl alcohol )	-
Cl no .3.5 [ Table 1, Sl no.(vi) ] Appendix A 7 (Aldehydes and acetone )	-
Cl no .3.5 [ Table 1, Sl no.(vii) ] Appendix A 8 (Sulphurous acids and other free acids )	-

-
" 500 ml x 2 Excluding except distillation range, relative density

11825

BIS, Eastern Regional Laboratory (ERL)

None

IS 14255 (1995)

Aertal bunched cables - For working voltages up to and including 1100 Volts - Specification

complete for Cat 01(Except melt flow, vicat, bending)

- View breakup
Rs.16650.00 for XLPE insulated single core cable Rs.15150.00 for PE insulated single core cable

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (Insulation)	-
6.1 (Flexibility class)	-
6.2 (Compactness)	-
6.2 (No of strands)	-
6.2 (Surface)	-
6.3 (Protective barrier)	-
6.4 (size of street lighting conductor)	-
6.5 (Size of messenger conductor )	-
6.6 (Joints in messenger conductor )	-
6.6 (Direction of outer layer)	-
7.2 ( Thickness of insulation)	-
7.3 (Tolerance on thickness of insulation )	-
7.4 (Aplication of the insulation )	-
7.5 (Colour of the insulation )	-
8.1 (Core identification)	-
8.2 (Core identification)	-
8.3 (Identification by other means)	-
9.1 (Assembly (Laying up))	-
9.2 (Assembly (Laying up))	-
9.3 (Direction of lay)	-
10.1 a) i) (Tests on phase/street light conductor: tensile test - Test method IS10810:Part 2)	-
10.1 a) ii) (Wrapping test - 10810: Part 3)	-
10.1 a) iii) (Resistance test - IS10810: Part 5)	-
10.1 b) i) (Test on messenger conductor: Breaking load - IS 10810: Part 2)	-
10.1 b) ii) (Test on messenger conductor: Elongation test - Cl 11.3)	-
10.1 b) iii) (Test on messenger conductor: Resistance test - IS 10810: Part 5)	-
10.1 c) i) (Physical tests for XLPE Insulation: Tensile strength - IS 10810: Part 7)	-
10.1 c) i) (Physical tests for XLPE Insulation: elongation at break - IS 10810: part 7)	-
10.1 c) ii) (Ageing in air oven : Tensile strength variation - IS 10810:Part 11)	-
10.1 c) ii) (Ageing in air oven : Elongation variation- IS 10810: Part 11)	-
10.1 c) iii) (Hot set test: Elongation under load - IS 10810: Part 30)	-
10.1 c) iii) (Hot set test: Permanent elongation (set) after cooling - IS 10810: Part 30)	-
10.1 c) iv) (Shrinkage test : Shrinkage - 10810:Part 12)	-
10.1 c) iv) (Shrinkage test : Crack Observed - 10810:Part 12)	-
10.1 c) v) (Water ahsorption (Gravimetric) - IS 10810: Part 33 )	-
10.1 d) i) (Physical test for PE insulation: Tensile strength - IS 10810: Part 7 )	-
10.1 d) i) (Physical test for PE insulation: elongation at break - IS 10810: Part 7)	-
10.1 f) (Insulation resistance (Volume resistivity) test a) volume resistivity at 27°C - IS 10810: Part 43)	-
10.1 f) (Insulation resistance (Volume resistivity) test b) volume resistivity at 70°C - IS 10810: Part 43)	-
10.1 g) (High voltage test - IS10810:Part 45)	-

-
Facility not available for breaking load of messenger conductor, Carbon Black test, Vicat Test, Environmental stress cracking for PE insulation. For XLPE water absorption test facility available upto 25 sq.mm. (Facility for nominal area of conductor, Tensile & Elongation above 2.0 mm thickness is not available). 5 mtr Aluminium wire before stranding to be provided additionally.

11826

BIS, Southern Regional Laboratory (SRL)

None

IS 1161 (2014)

Steel tubes for structural purposes - Specification (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 6 (Outer Diameter, Thickness & Mass)	-
Cl 7 (Workmanship)	-
Cl 11 (Tensile Test, Flattening Test & Cold Bend Test)	-
5 AND AS PER IS 10748 (COPPER)	-
5 AND AS PER IS 10748 (MICRO ALLOY)	-
5 AND AS PER IS 10748 (CARBON EQUIVALENT)	-
5 AND AS PER IS 10748 (CARBON)	-
Clause - 5.1, Table-3 ( ALUMINIUM)	-
Clause - 5.1, Table-3 (SILICON)	-
Clause - 5.1, Table-3 (NITROGEN)	-
Clause - 5.1, Table-3 (MANGANESE)	-
Clause - 5.1, Table-3 (PHOSPHURS)	-
Clause - 5.1, Table-3 (SULPHUR)	-

-
" mech - 1.5 m Chemical Facility is available Quantity: 5 Pieces of 5cm X 5cm Excluding except cold bend test

11827

BIS, Northern Regional Laboratory (NRL)

None

IS 1610 (2018)

Household sewing machines - General requirements (Fourth Revision)

- View breakup
Rs 5020/- + charges as per relevant ISS For Plating: Rs 2050 per part of the sample

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (Driving arrangement Hand Operated Sewing Machine)	-
4.1 (Sewing Mechanism Design )	-
4.2 (Sewing Mechanism Reverse stitch mechanism )	-
4.2.1 (Sewing Mechanism Stitch Regulator)	-
4.3 (Sewing Mechanism Thread Tension)	-
4.4 (Sewing Mechanism Timing)	-
4.7 (Sewing Mechanism Thread Spool Pin)	-
6 (Lubrication)	-
8 (WORKMANSHIP AND FINISH)	-
8 (WORKMANSHIP AND FINISH)	-
8 (WORKMANSHIP AND FINISH)	-
10.1 IS 7491 (Accuracy Requirement Functional Dimension Feed Dog Measuring Condition - Feed dog raised to its highest position )	-
10.1 IS 7491 (Accuracy Requirement Functional Dimension Shuttle and shuttle driver Measuring Condition - Shuttle heel at bottom - most position)	-
10.1 IS 7491 (Accuracy Requirement Functional Dimension Presser foot Measuring Condition - Presser foot in lifted condition)	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Needle bar Measuring Condition - Needle bar at lower-most condition)	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Needle bar Measuring Condition - Needle bar at lower-most condition)	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Thread take up lever Measuring Condition - Thread take up lever at top and intermediate position)	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Thread take up lever Measuring Condition - Thread take up lever at top and intermediate position)	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Shuttle Measuring Condition - Difference between highest & lowest position of needle bar.)	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Shuttle Measuring Condition - Tip of pin at top most bottom most position of needle bar)	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Shuttle Measuring Condition - Difference between highest & lowest position of needle bar.)	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Arm shaft Measuring Condition -At different fly wheel position (turn fly wheel by hand) axial push./pull to be given)	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Flywheel Measuring Condition - Rotate flywheel to Radially measure eccentrity)	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Feed section Measuring Condition - At its highest position above needle place)	-
10.2 IS 7492 (Sewing Requirement)	-
10.2 IS 7492 (Sewing Requirement)	-
10.2 IS 7492 (Sewing Requirement)	-
10.2 IS 7492 (Sewing Requirement)	-
10.2 IS 7492 (Sewing Requirement)	-
10.3 IS 7493 (Durability Requirement Needle bar Measuring Condition - Needle bar at lower-most condition)	-
10.1 IS 7491 (Accuracy Requirement Functional Dimension Shuttle and shuttle driver Measuring Condition - Shuttle heel at bottom - most position)	-
10.3 IS 7493 (Durability Requirement Thread take up lever Measuring Condition - Thread take up lever at top and intermediate position)	-
10.3 IS 7493 (Durability Requirement Thread take up lever Measuring Condition - Thread take up lever at top and intermediate position)	-
10.3 IS 7493 (Durability Requirement Shuttle Measuring Condition - Tip of pin at top most bottom most position of needle bar)	-
10.3 IS 7493 (Accuracy Requirement Assembly Clearance Shuttle Measuring Condition - Difference between two indicator readings when needle bar is at its highest and lowest position)	-
10.3 IS 7493 (Durability requirement Arm shaft Measuring Condition -At different fly wheel position (turn fly wheel by hand) axial push./pull to be given)	-
10.3 IS 7493 (Durability Requirement Feed section Measuring Condition - At its highest position above needle place)	-
12 (Marking)	-
12 (Marking)	-

-
Test facility is complete

11828

BIS, Northern Regional Laboratory (NRL)

None

IS 398 : Part 2 (1996)

Aluminium conductors for overhead transmission purposes - Specification: Part 2 aluminium conuuctors, galvanized steel - Reinforced (Third Revision)

- View breakup
(I) For galvanized steel core only (consisting of 7 steel strands)- Rs.2850.00, (II) For galvanized steel reinforced stranded conductors with nominal aluminium area upto and including 100mm2-(a) For single steel wire core (1 steel + 6 Aluminium)- Rs. 1950.00 (b) For 7 wire core (7 steel + 6 Aluminium) - Rs. 4000.00, (III) For galvanized steel reinforced stranded conductors with nominal aluminium area more than 100mm2 (excluding special tests as per Cl. 13.9, 13.10 & 13.11)-(a) For stranded conductors with 37 strands-Rs.7900/-, (b) For stranded conductors with 49 strands-Rs.10000/-, (c) For stranded conductors with 61 strands-Rs.11100/-,

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8.1.1 & 13.2 Table-1 (mech) (Diameter of Aluminium Wires Before Stranding)	-
8.1.1 & 13.2 Table-1 (mech) (Diameter of Aluminium Wires After Stranding)	-
8.1.1 & 13.2 Table 2 (mech) (Diameter of Steel Wires Before Stranding)	-
8.1.1 & 13.2 Table-1 (mech) (Diameter of Aluminium Wires After Stranding)	-
8.1.1 & 13.2 Table 2 (mech) (Diameter of Steel Wires After Stranding)	-
10 (elec) (Stranding)	-
10 (elec) (Stranding)	-
10 (elec) (Stranding)	-
10 (mech) (Stranding)	-
13.3 Table 1 (mech) (Breaking Load of Aluminium Wires Before Stranding)	-
13.3 Table 2 (mech) (Breaking Load of Steel Wires Before Stranding)	-
13.3 Table 1 (mech) (Breaking Load of Aluminium Wires After Stranding)	-
13.3 Table 2 (mech) (Breaking Load of Steel Wires After Stranding)	-
13.4.1 (mech) (Ductility by Torsion Test before stranding)	-
13.4.1 (mech) (Ductility by Torsion Test before stranding)	-
13.4.1 (mech) (Ductility by Torsion Test after stranding)	-
13.4.1 (mech) (Ductility by Torsion Test after stranding)	-
13.4.1 (mech) (Ductility by Torsion Test before stranding)	-
13.4.1 (mech) (Ductility by Torsion Test before stranding)	-
13.4.1 (mech) (Ductility by Torsion Test after stranding)	-
13.4.1 (mech) (Ductility by Torsion Test after stranding)	-
13.4.2 (elec) (Ductility by Elongation Test before stranding)	-
13.5.1 (mech) (Wrapping Test Aluminium Wires After Stranding)	-
13.4.2 (elec) (Ductility by Elongation Test after stranding)	-
13.5.1 (mech) (Wrapping Test Aluminium Wires After Stranding)	-
13.5.1 (mech) (Wrapping Test Aluminium Wires Before Stranding)	-
13.5.1 (mech) (Wrapping Test Aluminium Wires After Stranding)	-
13.5.2 (mech) (Wrapping Test Galvanized Steel Wires After Stranding)	-
13.5.2 (mech) (Wrapping Test Galvanized Steel Wires Before Stranding)	-
13.5.2 (mech) (Wrapping Test Galvanized Steel Wires After Stranding)	-
13.6 (elec) (Resistance test-Aluminium wire before Stranding)	-
13.6 (elec) (Resistance test-Aluminium wire after stranding)	-
13.7.2 (chem) (Mass of Zinc coating)	-
13.7.2 (chem) (Uniformity of Zinc coating)	-
13.8 Table-4 (mech) (Lay Ratio- Aluminium Wire Outermost Layer)	-
13.8 Table-4 (mech) (Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-
13.8 Table-4 (mech) (Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-
13.8 Table-4 (mech) (Lay Ratio- Steel Core (6 Wire Layer))	-
13.7.2 (chem) (Mass of Zinc coating)	-
13.7.2 (chem) (Uniformity of Zinc coating)	-

-
Excluding 1.)Complete Upto 100 sq. mm 2.) Above 100 Sq .mm Except Cl.13.9 surface condition test Cl.13.10 ultimate breaking load test on stranded conductor above 100 mm sq Cl.13.11 stress strain test on conductor

11829

BIS, Northern Regional Laboratory (NRL)

None

IS 1341 (2018)

Steel Butt Hinges - Specification (Sixth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 Tables 2 to 9 (3) (Length A)	-
5.1 Tables 2 to 9 (4) (Breadth B)	-
5.1 Tables 2 to 9 (4) (Breadth B1)	-
5.1 Tables 2 to 9 (4) (Breadth B2)	-
5.1 Tables 2 to 9 (5) (Thickness of Flap C)	-
5.1 Tables 2 to 9 (6) (Diameter of Hinge Pin D)	-
6.4.2 (X)	-
6.4.2 (Y)	-
6.4.2 (Z)	-
3 Tables 2 to 9 (Types)	-
5.1 Tables 2 to 9 (2) (Size of Hinge)	-
5.1 Tables 2 to 9 (7) (Number of Knuckles)	-
5.1 Tables 2 to 9 (8) (Number of Screw Holes)	-
5.1 Tables 2 to 9 (9) (Holes for Screw No.)	-
6.1 (General)	-
6.2.1 (Knuckles)	-
6.3 (Pins)	-
6.4 (Screw Holes)	-
6.4.2 (Position of Holes)	-
TABLE-1 (Clause-4) ( CARBON)	-
TABLE-1 (Clause-4) (SULPHUR)	-
TABLE-1 (Clause-4) (MANGANESE)	-
TABLE-1 (Clause-4) (PHOSPHURS)	-
Cl 4 & Table 1 (Silicon- IS 228(Part 2))	-
Clause 4 Table 1 (Nitrogen ( Flap))	-

-
Test facility is complete for mechanical Except Microalloying Elements

11830

BIS, Northern Regional Laboratory (NRL)

None

IS 398 : Part 1 (1996)

Aluminium conductors for overhead transmission purposes - Specification: Part 1 aluminium stranded conductors (Third Revision)

Rs.1600/- for 7 strands, Rs.3750/- for 19 strands View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
12.2, Table-1 (Measurement of diameter of individual aluminium wire)	-
12.3, Table-1 (Breaking load before stranding)	-
12.3, Table-1 (Breaking load after stranding)	-
12.4 (Wrapping test)	-
12.5, Table 1 (Resistance test)	-
12.6, Table 3 (Measurement of lay ratio)	-
9.3 (Stranding)	-
6 (Freedom from defects)	-

-
Test facility is complete

11831

BIS, Northern Regional Laboratory (NRL)

None

IS 1328 (1996)

Veneered Decorative Plywood -Specification

- View breakup
Rs. 5550/- for MR. Grade & material testing charges as per relevant referred ISs Rs. 6720/- for BWR Grade & material testing charges as per relevant referred Iss

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1.1 (Requirements - Open splits, checks or open joints - For Type 1 - Cl. 7.1.1)	-
7.2.1 (Requirements - Open splits, checks or open joints - For Type 2 - Cl. 7.2.1)	-
7.2.2 (Requirements - Other defects - For Type 2 - Cl. 7.2.2.)	-
8 (Dimensions & Tolerances - Length - Cl. 8)	-
8 (Dimensions & Tolerances - Width - Cl. 8)	-
8 (Dimensions & Tolerances - Thickness - Cl. 8)	-
8 (Dimensions & Tolerances - Edge Straightness - Annexure C)	-
8 (Dimensions & Tolerances - Squareness - Annexure C)	-
11 (Tests - Moisture Content - Part 1 of IS 1734)	-
11 (Tests - Water Resistance Test - Cl. 11.1.2.1 [for MR Grade])	-
11 (Tests - Water Resistance Test - Cl. 11.1.2.2 [for BWR Grade])	-
4.1 (Grade - For BWR)	-
4.1 (Grade - For MR)	-
4.2 (Type - For Type 1)	-
4.2 (Type - For Type 2)	-
7.1.2 (Requirements - Other defects - For Type 1 - Cl. 7.1.2)	-
7.2.3 (Requirements - Other Charcteristics and Manufacturing Defects - For Type 2 - Cl. 7.2.3)	-
9 (Finish - Cl. 9.1, 8.3)	-
9 (Finish - Cl. 9.2, 8.3)	-

-
Test facility is complete

11832

BIS, Northern Regional Laboratory (NRL)

None

IS 13095 (1991)

Butterfly valves for general purposes

Rs3300/-t View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (VALVE END CONNECTIONS)	-
5 (SERVICE APPLICATIONS)	-
6 ( NOMINAL SIZES )	-
7 (NOMINAL PRESSURES)	-
7.2 (Class designations)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Flange-D)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges-IS 6418 (Table 2/3/6/7/10)- Flange-b)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges-IS 6418 (Table 2/3/6/7/10)- Rasied Face-d4)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges-IS 6418 (Table 2/3/6/7/10)- Rasied Face-f)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Bolting )	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Drilling -Nos. )	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Drilling -d2)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Drilling -k)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Neck -d3)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Neck- r)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Flange-D)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Flange-b)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Rasied Face-d4)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Raised Face - f)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Bolting)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Drilling -Nos. )	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Drilling -d2 )	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Drilling -k)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Neck -d3)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Neck-r)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Pipe O.D.- d1)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Flange - D)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Flange - b)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Raised Face - d4)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Raised Face - f)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Drilling - Nos.)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Drilling -d2)	-
9-Annex B (BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Drilling -k)	-
9.1.1 ( Double Flanged Body Ends)	-
9.2.2 (Wafer Body Ends)	-
10.1 -Table1 (FACE TO FACE DIMENSIONS)	-
11 (Bodies)	-
12 (DISC AND SHAFT)	-
13 (SEATING AND LININGS)	-
14.2 (BEARINGS)	-
14.3 (BEARINGS)	-
16 (OPERATION)	-
17.1 (Performance Testing)	-
17.2 (Body Test)	-
17.3 (Seat Test)	-
17.4 (Disc Strength Test)	-

-
Except Microalloying Elements

11833

BIS, Central Laboratory (CL)

None

IS 8944 (2005)

Chlorpyrifos, emulsifiable concentrates - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2.1 (Description)	-
3.2.2 (Cold Test)	-
3.2.3 (Flash Point (Abel))	-
3.2.4 (Emulsion Stability)	-
3.3.1 (Chloropyrifos content)	-
3.3.2 (Acidity (as H2SO4), )	-

-
Excluding Cl. 3.3.1 Content;

11834

BIS, Southern Regional Laboratory (SRL)

None

IS 10109 (2018)

Oil pressure stoves - Offset burner type - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
9.6 (Resistance to Draught)	-
9.7 (Fuel Creep)	-
9.1.1 (Air Pressure Test)	-
9.1.2 ( Safety Pressure Test)	-
9.1.3 (Bursting Pressure Test)	-
5.4 (Plastic components (for example, handles) shall be free from fissures, distortions, blemishes and discolouration.)	-
6.2 (The vassel when kept on the stove shall not touch burner top.)	-
6.4 (Minimum Sheet thickness of fuel container)	-
6.5 (Maximum height of the fuel feed pipe into the container from the bottom)	-
7.1.1 (Construction, General)	-
7.1.1 (Construction, General)	-
7.1.1 (Construction, General The base of the fuel container clear from the ground )	-
7.1.1 (Construction, General The fuel container may be of detachable type)	-
7.1.3 (Regulator near the socket may be provided for opening or closing of the fuel supply.In case the Regulator is not provided,the kerosene oil should not come out of the nipple when the tank is full under atmospheric pressure.)	-
7.3 (Pump)	-
7.4 ( Pressure Release Screw)	-
7.7 (Taps)	-
7.1 (Pricker)	-

-
" 1 set " Excluding Except Burner assembly, Washer, Workmanship, Fuel Consumption & Thermal efficiency ,

11835

BIS, Southern Regional Laboratory (SRL)

None

IS 3205 (1984)

Specification for precipitated barium carbonate, technical (First Revision)

Rs 1575/- Grade 1; Rs 1125/- for Gr 2 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (Description)	-
3.2, Table 1 and Appendix A-2 of IS 3205 (Barium (as Ba ) - for All Grades)	-
3.2, Table 1 and Appendix A-4 of IS 3205 (Moisture - For Grade 1 )	-
3.2, Table 1 and Appendix A-4 of IS 3205 (Moisture - For Grade 2)	-
3.2, Table 1 and Appendix A-5 of IS 3205 (Matter insolubile in hydrochloric acid - For Grade 1)	-
3.2, Table 1 and Appendix A-5 of IS 3205 (Matter insolubile in hydrochloric acid - For Grade 2)	-
3.2, Table 1 and Appendix A-6 of IS 3205 (Free Alkali - For Grade 2)	-
3.2, Table 1 and Appendix A-7 of IS 3205 (Water Soluble Sulphide ( as BaS ) -For Grade 1)	-
3.2, Table 1 and Appendix A-7 of IS 3205 (Water Soluble Sulphide ( as BaS ) -For Grade 2)	-
3.2, Table 1 and Appendix A-8 of IS 3205 (Total Sulphur ( as SO4 ) - For Grade 1)	-
3.2, Table 1 and Appendix A-9 of IS 3205 (Alkali and other metasulphates ( as BaSO4 ) - For Grade 1 )	-
3.2, Table 1 and Appendix A-9 of IS 3205 (Alkali and other metasulphates ( as BaSO4 ) - For Grade 2)	-
3.2, Table 1 and Appendix A-10 of IS 3205 (Sodium Oxides ( as NaO2 ) - For Grade 1)	-
3.2, Table 1 and Appendix A-11 of IS 3205 (Iron ( as Fe2O3) - For Grade 1)	-
3.2, Table 1 and Appendix A-11 of IS 3205 (Iron ( as Fe2O3) - For Grade 2)	-
3.2, Table 1 and Appendix A-14 of IS 3205 (Reaction efficiency ( after 45 minutes ) - For Grade 2)	-

-
" 500 g " Excluding except carbonates for all grades, residue retained on 63 microns IS sieve for grade 1

11836

BIS, Central Laboratory (CL)

None

IS 9798 (2013)

Low pressure regulators for use with liquefied petroleum gas (LPG) - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2 IS 742 (Material)	-
4.1.1 IS 2305 (Material)	-
4.2.1a (Finish)	-
4.2.1b IS 9844 IS 6009 (Finish)	-
4.3.1 (Diaphragm Material)	-
4.3.2 IS 3400(Part 4) (The material shall not show change of more than 10 IRHD when subjected to ageing of 72 h at 70°C in accordance with the method prescribed in 3 or 4 of IS 3400 (Part 4))	-
4.3.3 (Clamping test)	-
4.3.4 Annex C (Bursting & Pull out test)	-
4.3.5ai Annex D (The material shall, after immersion in n-pentane or octet commercial LPG for 72 h, meet the appropriate requirements specified in Annex D Diaphragm: Extractable )	-
4.3.5b IS 3400(Part 2) (Changes in hardness, before and after the immersion )	-
4.3.7 Annex E (The material shall have 25 percent max compression set when subjected to compression set test in accordance with the method prescribed in Annex E.)	-
4.4.1 (Valve Pad Material)	-
4.4.2ai Annex D (The material shall, after immersion in n-pentane or octet commercial LPG for 72 h, meet the appropriate requirements specified in Annex D Extractable )	-
4.4.2aii Annex D ( Absorbed)	-
4.4.2b IS 3400(Part 2) (Changes in hardness, before and after the test)	-
4.4.3 IS 3400(Part 4) (The material shall not show change of more than 10 IRHD when subjected to ageing of 72 h at 70°C in accordance with the method prescribed in 3 or 4 of IS 3400 (Part 4))	-
4.4.4 (Valve Pad Material)	-
4.4.5 Annex E (The material shall have 40 percent max compression set when subjected to compression set test in accordance with the method prescribed in Annex E.)	-
4.5,4.4.1 (Seals O rings and rubber components other than diaphragm and valve pad )	-
4.5,4.4.2i Annex D (The material shall, after immersion in n-pentane or octet commercial LPG for 72 h, meet the appropriate requirements specified in Annex D Extractable )	-
4.5,4.4.2ii Annex D ( Absorbed)	-
4.5,4.4.2b IS 3400(Part 2) (Changes in hardness, before and after the test)	-
4.5,4.4.3 IS 3400(Part 4) (The material shall not show change of more than 10 IRHD when subjected to ageing of 72 h at 70°C in accordance with the method prescribed in 3 or 4 of IS 3400 (Part 4))	-
4.5,4.4.5 Annex E (The material shall have 40 percent max compression set when subjected to compression set test in accordance with the method prescribed in Annex E.)	-
4.5,4.4.1 (Seals O rings and rubber components other than diaphragm and valve pad )	-
4.5,4.4.2i Annex D (The material shall, after immersion in n-pentane or octet commercial LPG for 72 h, meet the appropriate requirements specified in Annex D Extractable )	-
4.5,4.4.2ii Annex D ( Absorbed)	-
4.5,4.4.2b IS 3400(Part 2) (Changes in hardness, before and after the test)	-
4.5,4.4.3 IS 3400(Part 4) (The material shall not show change of more than 10 IRHD when subjected to ageing of 72 h at 70°C in accordance with the method prescribed in 3 or 4 of IS 3400 (Part 4))	-
4.5,4.4.5 Annex E (The material shall have 40 percent max compression set when subjected to compression set test in accordance with the method prescribed in Annex E.)	-
4.5,4.4.1 (Seals O rings and rubber components other than diaphragm and valve pad )	-
4.5,4.4.2i Annex D (The material shall, after immersion in n-pentane or octet commercial LPG for 72 h, meet the appropriate requirements specified in Annex D Extractable )	-
4.5,4.4.2ii Annex D ( Absorbed)	-
4.5,4.4.2b IS 3400(Part 2) (Changes in hardness, before and after the test)	-
4.5,4.4.3 IS 3400(Part 4) (The material shall not show change of more than 10 IRHD when subjected to ageing of 72 h at 70°C in accordance with the method prescribed in 3 or 4 of IS 3400 (Part 4))	-
4.5,4.4.5 Annex E (The material shall have 40 percent max compression set when subjected to compression set test in accordance with the method prescribed in Annex E.)	-
5.2 (Construction and Workmanship)	-
5.5 (Inlet Connection)	-
5.5 (Inlet Connection)	-
5.5 (Inlet Connection)	-
5.6,5.6.1 (Outlet Connection:- Non-threaded Outlet Connection)	-
5.7 (Body)	-
5.8 (Vent)	-
5.10.1 (Valve Pad Fitting)	-
5.11.1,8.11 Table 1 (The fixing of the inlet connection on to the regulator body , whether it is of the threaded or non - threaded type or in one piece, shall withstand the following tests, under the conditions defined in 8.11 (see Table 1))	-
5.11.1,8.11 Table 1 (The fixing of the inlet connection on to the regulator body , whether it is of the threaded or non - threaded type or in one piece, shall withstand the following tests, under the conditions defined in 8.11 (see Table 1))	-
5.12.1,8.11 Table 3 (The regulators when installed as indicated in the installation instruction shall resist the following tests under the conditions defined in 8.11 (see Table 3 ))	-
5.11.2a,8.11 Table 2 (The fixing of the outlet connection on to the regulator body, whether it is of the threaded, or non-threaded type or in one piece, shall resist the following tests, under the conditions defined in 8.11 (see Table 2):a)For non - threaded hose connection)	-
5.11.2b,8.11 Table 2 (The fixing of the outlet connection on to the regulator body, whether it is of the threaded, or non-threaded type or in one piece, shall resist the following tests, under the conditions defined in 8.11 (see Table 2):b)For threaded unions)	-
6,6.1,6.2 (SOUNDNESS)	-
6,6.1,6.2 (SOUNDNESS)	-
6.3 (SOUNDNESS)	-
6.4 (SOUNDNESS)	-
8.2 (CHATTER)	-
8.9 (Performance (Before Cycle test, Low Temp. Test and High Temp. Test) Inlet Pressure Flow Rate )	-
8.9 (0.5 kgf/cm2 100 % )	-
8.9 (17 kgf/cm2 10 % )	-
8.9 (Static(lock up) pressure)	-
8.9 (Performance (Before Cycle test, Low Temp. Test and High Temp. Test) Inlet Pressure Flow Rate )	-
8.10.1 Annex G (Cycle Test)	-
6,6.1,6.2 (SOUNDNESS (After Cycle Test))	-
8.9 (Performance (After Cycle test) Inlet Pressure Flow Rate )	-
8.10.2 Annex H 8.9 (Low Temperature Test Performance test after exposure to temperature at -200 C for 10 Min and back to ambient condition. Inlet Pressure Flow Rate)	-
8.9 (Static(lock up) pressure)	-
8.10.3 Annex H 8.9 (High Temperature Test Performance test after exposure to temperature at 650 C for 10 Min and back to ambient condition. Inlet Pressure Flow Rate)	-
8.9 (0.5 kgf/cm2 100 % )	-
8.9 (17 kgf/cm2 10 % )	-
8.9 (Static(lock up) pressure)	-
4.4.5 Annex E (The material shall have 40 percent max compression set when subjected to compression set test in accordance with the method prescribed in Annex E.)	-
Cl. 4.2 (Aluminium)	-
Cl. 4.2 (Copper)	-
Cl. 4.2 (Magnesium)	-
Cl. 4.2 (Iron)	-
Cl. 4.2 (Lead)	-
Cl. 4.2 (Cadmium)	-
Cl. 4.2 (Tin)	-
Cl. 4.2 (Thalium+ Indium)	-
Cl. 4.2 (Nickel)	-
Cl. 4.2 (Zinc)	-
Cl. 4.2 (Chromium)	-

-
-

11837

BIS, Southern Regional Laboratory (SRL)

None

IS 11587 (1986)

Specification for structural weather resistant steels

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 4 (Grades)	-
Cl 8 (Tensile Test)	-
Cl 10 (Impact Test)	-
Cl 11 (Flattening Test)	-
Cl 12 (Freedom from Defects)	-
Cl 13 (Dimensions)	-
Cl 16 (Mass)	-
Cl 13 (Dimensions)	-
Cl 16 (Mass)	-

-
" 1 m Excluding except chemical tests (Prepared test pieces are required for Impact test)

11838

BIS, Central Laboratory (CL)

None

IS 1554 : Part 1 (1988)

Specification for pvc insulated (Heavy Duty) electric cables: Part 1 for working voltages up to and including 1100 v (Third Revision)

- View breakup
Rs.16650/- for single core unarmoured cable, Rs.22500/- for two core, unarmoured cable, Rs.26700/- for two core armoured cable (Excluding addl. Type test for cables with improved fire performance.) For multi core cables, extra charges @ 35 % for each additional core shall be levied. Material testing charges as per relevant referred ISs Testing charges for Additional Type Tests for Improved Fire Performance Tests: Rs. 7100/- for category C1 Rs. 11700/- for category C2

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (MATERIALS : CONDUCTOR)	-
4.1.1 (INSULATION : General Purjose Insulaiion)	-
4.1.2 (INSULATION : Heat Resisting Insulation)	-
5.1 (MATERIALS : FILLER AND INNER SHEATH)	-
6.1 (MATERIALS : ARMGURING)	-
7.1.1 (OUTER SHEATH : For Cables with General Purpose InsuIafion)	-
7.1.2 (OUTER SHEATH : For Cables with Heat Resisting InsuIalion)	-
8.1 (CONSTRUCTION : CONDUCTOR)	-
8.2 (CONSTRUCTION : CONDUCTOR)	-
9.2 (INSULATION : Thickness of Insulation)	-
9.4 (INSULATION : Application of Insulation)	-
10.1 (CORE IDENTIFICATION)	-
10.2 (CORE IDENTIFICATION)	-
10.3 (CORE IDENTIFICATION)	-
10.3.1 (Arrangement of Marking)	-
11.1 (LAYING UP OF CORES)	-
12.1 (INNER SHEATH)	-
12.2 (INNER SHEATH)	-
12.3 (INNER SHEATH :Thickness of Inner Sheath)	-
13.1.1 (ARMOURING : Application)	-
13.1.2 (Armouring: Coverage )	-
13.1.3 (ARMOURING : Direction of lay )	-
13.2 (ARMOURING : Type of Armour)	-
13.3 (Armouring : Dimensions -Wire Diameter)	-
13.3 (Armouring : Dimensions -Formed wire )	-
13.4 (ARMOURING : Joints)	-
13.5.1 (ARMOURING : Resistance)	-
13.5.2 (ARMOURING : Resistance)	-
13.6 a) (ARMOURING: Tensile Strength)	-
13.6 b) (ARMOURING: Elongation )	-
13.6 f) (ARMOURING: Mass of zinc coating )	-
13.6 g) (ARMOURING: Resistivity)	-
14.1 (OUTER SHEATH)	-
14.3 (OUTER SHEATH : Colour )	-
14.4.1 (Thickness of Outer Sheath : Unarmowed Cables)	-
14.4.2 (Thickness of Outer Sheath : Armoured Cables)	-
15.1 a) 1) (Tests on conductor : Annealing test ( for copper ))	-
15.1 a) 2) (Tensile test (for aluminium) - Before stranding )	-
15.1 a) 2) (Tensile test (for aluminium) - After stranding )	-
15.1 a) 3) (Tests on conductor : Wrapping test ( for aluminium ))	-
15.1 a) 4) (Tests on conductor : Conductor resistance test)	-
15.1 a) 4) (Resistance test - Neutral conductor )	-
15.1 d)1) (Phyaical tests for insulation : Tensile Test)	-
15.1 d)1) (Phyaical tests for insulation : Elongation )	-
15.1 d)1) (Physical tests for sheath : Tensile stregth )	-
15.1 d)1) (Physical tests for sheath : Elongation )	-
15.1 d)2) (Phyaical tests for insulation- Ageing in air Oven : Tensile Test)	-
15.1 d)2) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-
15.1 d)2) (Phyaical tests for insulation - Ageing in air oven : Elongation )	-
15.1 d)2) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-
15.1 d)2) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-
15.1 d)2) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-
15.1 d)2) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-
15.1 d)5) ( Loss of mass in air oven- Insulation )	-
15.1 d)5) ( Loss of mass in air oven- sheath )	-
15.1 d)3) (Phyaical tests for insulation : Shrinkage )	-
15.1 d)3) (Phyaical tests for insulation : Shrinkage - Crack observed )	-
15.1 d)3) (Phyaical tests for Sheath : Shrinkage )	-
15.1 d)3) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-
15.1 d)4) (Hot deformation : Insulation )	-
15.1 d)4) (Hot deformation : Sheath )	-
15.1 d)6) (Heat shock test- Insulation )	-
15.1 d)6) (Heat shock test- sheath )	-
15.1 d)7) (Thermal stability- insulation )	-
15.1 d)7) (Thermal stability- Sheath )	-
15.1 e) (Insulation resistance test : Volume Resistivity )	-
15.1 e) (Insulation resistance test : IR Constant )	-
15.1 f) (High voltage test ( water immersion test ))	-
15.1 g) (High voltage test at room temperature)	-
16.4 (Flammability Test)	-
15.4 a) (Cold bend test- Insulation ( Optional test))	-
15.4 a) (Cold bend test- Sheath ( Optional test))	-
15.4 b) (Cold impact test- Insulation ( Optional test))	-
15.4 b) (Cold impact test- Sheath ( Optional test))	-
15.4 c) (Armour resistance test ( for other than mining cables ).- Optional test )	-
17.1 (IDENTIFICATION : Manufacturer’s Identification)	-
17.2 (IDENTIFICATION : Cable Identification)	-
17.3 (IDENTIFICATION : Cable Code)	-
13.6 c) (ARMOURING: Torsion Test (For round wire ) )	-
13.6 d) (ARMOURING: Winding Test(For formed wire))	-
13.6 e) (ARMOURING: Uniformity of zinc coating)	-
Cl.8 (Conductor, Number of wires.)	-
Cl.8 (Conductor, Number of wires.)	-
Cl.8 (Flexibility class)	-
[(Cl.15), (d), 2] (After ageing, Elongation of Sheath [Percentage])	-

-
Except Cat C1 & C2

11839

BIS, Central Laboratory (CL)

None

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

- View breakup
Rs. 8100/- Excluding Impact and Y-Groove crackability Test

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 18 (Weight)	-
Cl 15 (Length, Width & Thickness)	-
Cl 10.3 (UTM)	-
Cl 7 (Workmanship)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Clause - 5, 8.1 & 8.2 (E250, ALUMINIUM)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Carbon Equivalent- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-

-
Grade/Designation, Quality type of killing and declaration regarding micro alloying elements addition may please be declared. Sample size- 5 pcs of 5 cm x 5 cm having dia> 3mm and thickness >0.8 mm; Excluding -; Y-groove crackability test

11840

BIS, Bengaluru Branch Laboratory (BNBL)

None

IS 10086 (1982)

Specificaton for moulds for use in tests of cement and concrete

Rs 14700/- and Material testing charges as per relevan View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5.1 (Construction)	-
Cl 5.3 (Arangement for fastening / Clamping)	-

-
Test facility not available for Material Testing

11841

BIS, Northern Regional Laboratory (NRL)

None

IS 1554 : Part 1 (1988)

Specification for pvc insulated (Heavy Duty) electric cables: Part 1 for working voltages up to and including 1100 v (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (MATERIALS : CONDUCTOR)	-
4.1.1 (INSULATION : General Purjose Insulaiion)	-
4.1.2 (INSULATION : Heat Resisting Insulation)	-
5.1 (MATERIALS : FILLER AND INNER SHEATH)	-
5.2 (MATERIALS : FILLER AND INNER SHEATH)	-
6.1 (MATERIALS : ARMGURING)	-
6.2 (MATERIALS : ARMGURING)	-
7.1.1 (OUTER SHEATH : For Cables with General Purpose InsuIafion)	-
7.1.2 (OUTER SHEATH : For Cables with Heat Resisting InsuIalion)	-
8.1 (CONSTRUCTION : CONDUCTOR)	-
8.2 (CONSTRUCTION : CONDUCTOR)	-
9.1 (INSULATION )	-
9.2 (INSULATION : Thickness of Insulation)	-
9.3 (INSULATION :Tolerance on Thickness of Insulation)	-
9.4 (INSULATION : Application of Insulation)	-
10.1 (CORE IDENTIFICATION)	-
10.2 (CORE IDENTIFICATION)	-
10.3 (CORE IDENTIFICATION)	-
10.3.1 (Arrangement of Marking)	-
11.1 (LAYING UP OF CORES)	-
11.2 (LAYING UP OF CORES)	-
12.1 (INNER SHEATH)	-
12.2 (INNER SHEATH)	-
12.3 (INNER SHEATH :Thickness of Inner Sheath)	-
12.3.1 (INNER SHEATH :Thickness of Inner Sheath)	-
13.1.1 (ARMOURING : Application)	-
13.1.2 (Armouring: Coverage )	-
13.1.3 (ARMOURING : Direction of lay )	-
13.2 (ARMOURING : Type of Armour)	-
13.1.4 (ARMOURING : Application)	-
13.2.1 (ARMOURING : Type of Armour)	-
13.3 (Armouring : Dimensions -Wire Diameter)	-
13.3 (Armouring : Dimensions -Formed wire )	-
13.4 (ARMOURING : Joints)	-
13.5.1 (ARMOURING : Resistance)	-
13.5.2 (ARMOURING : Resistance)	-
13.6 a) (ARMOURING: Tensile Strength)	-
13.6 b) (ARMOURING: Elongation )	-
13.6 c) (ARMOURING: Torsion Test (For round wire ) )	-
13.6 d) (ARMOURING: Winding Test(For formed wire))	-
13.6 e) (ARMOURING: Uniformity of zinc coating)	-
13.6 f) (ARMOURING: Mass of zinc coating )	-
13.6 g) (ARMOURING: Resistivity)	-
14.1 (OUTER SHEATH)	-
14.2 (OUTER SHEATH)	-
14.3 (OUTER SHEATH : Colour )	-
14.4.1 (Thickness of Outer Sheath : Unarmowed Cables)	-
14.4.2 (Thickness of Outer Sheath : Armoured Cables)	-
15.1 a) 1) (Tests on conductor : Annealing test ( for copper ))	-
15.1 a) 2) (Tensile test (for aluminium) - Before stranding )	-
15.1 a) 2) (Tensile test (for aluminium) - After stranding )	-
15.1 a) 3) (Tests on conductor : Wrapping test ( for aluminium ))	-
15.1 a) 4) (Tests on conductor : Conductor resistance test)	-
15.1 a) 4) (Resistance test - Neutral conductor )	-
15.1 d)1) (Phyaical tests for insulation : Tensile Test)	-
15.1 d)1) (Phyaical tests for insulation : Elongation )	-
15.1 d)1) (Physical tests for sheath : Tensile stregth )	-
15.1 d)1) (Physical tests for sheath : Elongation )	-
15.1 d)2) (Phyaical tests for insulation- Ageing in air Oven : Tensile Test)	-
15.1 d)2) (Phyaical tests for insulation - Ageing in air oven : Elongation )	-
15.1 d)2) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-
15.1 d)2) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-
15.1 d)2) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-
15.1 d)2) (Physical tests for outer sheath -Ageing in air oven : Elongation )	-
15.1 d)2) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-
15.1 d)2) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-
15.1 d)3) (Phyaical tests for insulation : Shrinkage )	-
15.1 d)3) (Phyaical tests for insulation : Shrinkage - Crack observed )	-
15.1 d)3) (Phyaical tests for Sheath : Shrinkage )	-
15.1 d)3) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-
15.1 d)4) (Hot deformation : Insulation )	-
15.1 d)4) (Hot deformation : Sheath )	-
15.1 d)5) ( Loss of mass in air oven- Insulation )	-
15.1 d)5) ( Loss of mass in air oven- sheath )	-
15.1 d)5) ( Loss of mass in air oven- Insulation )	-
15.1 d)5) ( Loss of mass in air oven- sheath )	-
15.1 d)6) (Heat shock test- Insulation )	-
15.1 d)6) (Heat shock test- sheath )	-
15.1 d)7) (Thermal stability- insulation )	-
15.1 d)7) (Thermal stability- Sheath )	-
15.1 e) (Insulation resistance test : Volume Resistivity )	-
15.1 e) (Insulation resistance test : IR Constant )	-
15.1 f) (High voltage test ( water immersion test ))	-
15.1 g) (High voltage test at room temperature)	-
15.1 f) (High voltage test ( water immersion test ))	-
15.1 g) (High voltage test at room temperature)	-
15.1 g) (High voltage test at room temperature)	-
15.4 a) (Cold bend test- Insulation ( Optional test))	-
15.4 a) (Cold bend test- Sheath ( Optional test))	-
15.4 b) (Cold impact test- Insulation ( Optional test))	-
15.4 b) (Cold impact test- Sheath ( Optional test))	-
15.4 c) (Armour resistance test ( for other than mining cables ).- Optional test )	-
16.1 (DETAILS OF TESTS : General)	-
16.2 (DETAILS OF TESTS : High Voltage Test at Room Temperature)	-
16.3.1 (High Voltage Test ( Water Immersion Test ) : a.c. Test)	-
16.3.2 (High Voltage Test ( Water Immersion Test ) : d.c. Test)	-
16.4 (Flammability Test)	-
16.5 (Oxygen Index Test)	-
16.6 (Flame Retardance Test on Single Cables)	-
16.7 (Flame Retardance Test on Bunched Cables)	-
16.1 (Temperature Index)	-
16.5 (Oxygen Index Test)	-
16.1 (Temperature Index)	-
17.1 (IDENTIFICATION : Manufacturer’s Identification)	-
17.2 (IDENTIFICATION : Cable Identification)	-
17.2.1 (IDENTIFICATION : Cable Identification)	-
17.3 (IDENTIFICATION : Cable Code)	-
16.9 (Test for Halogen Acid Gas Evolution)	-

-
Test facility is complete

11842

BIS, Southern Regional Laboratory (SRL)

None

IS 398 : Part 1 (1996)

Aluminium conductors for overhead transmission purposes - Specification: Part 1 aluminium stranded conductors (Third Revision)

AAAC

Rs.1600/- for 7 strands, Rs.3750/- for 19 strands View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
12.2, Table-1 (Measurement of diameter of individual aluminium wire)	-
12.3, Table-1 (Breaking load before stranding)	-
12.3, Table-1 (Breaking load after stranding)	-
12.4 (Wrapping test)	-
12.5, Table 1 (Resistance test)	-
12.6, Table 3 (Measurement of lay ratio)	-
9.3 (Stranding)	-
6 (Freedom from defects)	-

-
" 5 m "

11843

BIS, Northern Regional Laboratory (NRL)

None

IS 1239 : Part 1 (2004)

Steel tubes, tubulars and other wrought steel fittings - Specification: Part 1 steel tubes (Sixth Revision)

Rs. 9200/- Excluding test on joints View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (Outer Diameter, Thickness & Mass)	-
Cl 14 (Tensile Test, Flattening Test & Bend Test)	-
Cl 10.1 (Manufacturing )	-
Cl 10.1.1 (Manufacturing )	-
Cl 12 (Workmanship)	-
Cl 15 (Workmanship)	-
7, 6.1.1 (CARBON)	-
7, 6.1.1 (SULPHUR)	-
7, 6.1.1 (PHOSPHURS)	-
7, 6.1.1 (SILICON)	-
7, 6.1.1 (NITROGEN)	-
7, 6.1.1 (ALUMINIUM)	-
Cl. 14.1 (Tensile Strength)	-
Cl. 14.1.1 (Elongation)	-
Cl. 14.2 (Bend Test (uto and including 50 mm NB))	-
Cl. 14.3 (Flattening test (Over 50 mm NB))	-
Cl. 8 Table 3,4 & 5 (Outside Diameter)	-
Cl. 8, 9 Table 3,4 & 5 (Thickness)	-
Cl. 6.5 (Height of Internal Fin)	-

-
Except Microalloying Elements

11844

BIS, Northern Regional Laboratory (NRL)

None

IS 1161 (2014)

Steel tubes for structural purposes - Specification (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 7 (Workmanship)	-
Cl 8 (Workmanship)	-
Cl 9 (Workmanship)	-
Cl 13 (Workmanship)	-
Clause - 5.1, Table-3 ( CARBON)	-
Clause - 5.1, Table-3 (SULPHUR)	-
Clause - 5.1, Table-3 (SILICON)	-
Clause - 5.1, Table-3 (MANGANESE)	-
Clause - 5.1, Table-3 (PHOSPHURS)	-
Clause - 5.1, Table-3 (NITROGEN)	-
8 AND AS PER IS 4736 (MASS OF ZINC COATING)	-
8 AND AS PER IS 4736 (UNIFORMITY OF ZINC COATING)	-
Cl. 11.2 Table 2 (Yield strength)	-
3.1 & 6.1, 6.1.1 & 6.1.3 , Table 1 (Outer Diameter - SOP MT-23)	-
Cl. 6 , 6.2 Table 1 (Weight)	-
Cl. 6 , 6.2 Table 1 (Thickness)	-
Cl 11.3.1 (Flattening test (over 50 mm NB))	-
Cl. 11.2 Table 2 (Elongation)	-
Cl 11.3.1 (Cold bend test (upto & including 50 mm NB))	-
12 (Marking)	-
10 (Lengths)	-
Cl 11 (Tensile Test, Flattening Test & Cold Bend Test)	-
5 AND AS PER IS 10748 (MICRO ALLOY)	-

-
-

11845

BIS, Northern Regional Laboratory (NRL)

None

IS 1879 (2010)

Malleable cast iron pipe fittings - Specification (Third Revision)

Rs.7800.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 (Tensile Strength - IS 14329)	-
6.1 (Elongation - Is 14329)	-
7.2- Table 2 (Wall thickness of fittings - IS 1879)	-
7.5 - Table 2 (Projection of Rainforcement - IS 1879)	-
7.5 - Table 3 (Width of Rainforcement - IS 1879)	-
7.1 - Table 4 to Table 27 (a - IS 1879)	-
7.1 - Table 4 to Table 27 (b - IS 1879)	-
7.1 - Table 4 to Table 27 (c- IS 1879)	-
7.1 - Table 4 to Table 27 (d- IS 1879)	-
7.1 - Table 28 (d -IS 1879)	-
8.1 (Thread -IS 554)	-
8.2 (Alignment of threads -IS 554)	-
11 (Pressure Test)	-
5.1.1 (Type of Fittings - IS 1879)	-
5.1.2 (Size designation - IS 1879)	-
5.1.2.2 (Unequal fitting -IS 1879)	-
5.1.3 (Right and Left hand thread - IS 1879)	-
5.1.1 (Code Number -IS 1879)	-
10.iv) (Freedom from defects IS 4759)	-
12 (Compression Test)	-
10.iii) (Adhesion of Galvanized coating IS 2629)	-
10.i) (chem) (Mass of Galvanized coating)	-
10.ii) (chem) (Uniformity of Galvanized coating-IS 2633)	-
9 (Freedom from defects )	-
7.1 - Table 28 (D - IS 1879)	-
5.1.2.1 (Equal fitting - IS 1879)	-
10.i) (Mass of Galvanized coating )	-
10.ii) (chem) (Uniformity of Galvanized coating-IS 2633)	-

-
Test facility is complete

11846

BIS, Southern Regional Laboratory (SRL)

None

IS 398 : Part 4 (1994)

Aluminium conductors for overhead transmission purposes: Part 4 aluminium alloy stranded conductors (Aluminium - Magnesium - Silicon Type) - Specification (Third Revision)

AAAC

Rs 825/- upto 7 wires, Rs 1425/- upto 19 wires View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 (Freedom from Defects)	-
7.1 Table-1 (Dimensional measurement of wires)	-
7.2.2 Table-2, Table-4 (Calculated resistance of Stranded Conductor)	-
8.1 (Joints in wires-Conductors Containing Seven Wires)	-
8.2 (Joints in wires-Conductors Containing More Than Seven Wires)	-
9.1 (Stranding)	-
9.2 Table 3 (Lay Ratio of stranded conductors)	-
9.3 (Direction of Lay)	-
9.4 (Multiple layers of wires)	-
11 (Packing and Marking)	-
12.2 Table 1 (Breaking Load Test- Before Stranding)	-
12.2 Table 1 (Breaking Load Test- After Stranding)	-
12.3 Table 1 (Elongation Test- Before Stranding)	-
12.3 Table 1 (Elongation Test- After Stranding)	-
12.3 Table 1 (Elongation Test- Before Stranding)	-
12.3 Table 1 (Elongation Test- After Stranding)	-
12.4 Table 1 (Resistance of Aluminium wire)	-
9.2 Table 3 (Lay Ratio of stranded conductors)	-

-
5 m

11847

BIS, Southern Regional Laboratory (SRL)

None

IS 11169 : Part 2 (1989)

Steels for cold heading/cold extrusion applicationsspecification: Part 2 stainless steels

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7 (FREEDOM FROM DEFECTS)	-
8.2, table 5 (i) Yield stess/.2% Proof stress, Mpa)	-
8.2, table 5 (ii)Ultimate Tensile Strength, Mpa)	-
8.2, table 5 (iii)Elongation, %)	-
8.2, table 5 (v)Impact strength, J)	-

-
" mech - 2 x 1 m Excluding except chemical tests

11848

BIS, Southern Regional Laboratory (SRL)

None

IS 261 (1982)

Specification for copper sulphate (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
1(i) Table 1 (Copper, Tech, A-2)	-
1(ii) Table 1 (Matter insoluble in water, Tech, A-3)	-
1(iii) Table 1 (Soluble iron and aluminium compounds ( as Fe ), Tech, A-4)	-
1(iv) Table 1 (pH value, Tech, A-5)	-
1(v) Table 1 (Chloride ( as Cl ), Tech, A-6)	-
1(vi) Table 1 (Arsenic ( as As2O3 ), Tech, A-7)	-
1(vii) Table 1 (Lead and zinc, Tech, A-8)	-

-
" 500 g

11849

BIS, Northern Regional Laboratory (NRL)

None

IS 1165 (2002)

Milk powder - Specification (First Revision)

- View breakup
The complete testing charges for the product are Rs.5215x2=Rs.10430.00

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.4.5 (Moisture)	-
3.4.5 (Total solids)	-
3.4.5 (Fat)	-
3.4.5 (Insolubility index)	-
3.4.5 (Total ash)	-
3.4.5 (Titratable acidity (lactic acid))	-
3.1 (Description)	-
3.2 (Flavour and Taste)	-
3.5 (Bacterial count)	-
3.5.2 (Coliform count)	-
3.5.3 (Staphylococcus Aureus)	-
3.5.4 (Salmonella)	-
3.5.5 (Shigella)	-

-
Except Table 3

11850

BIS, Northern Regional Laboratory (NRL)

None

IS 10325 (2000)

Square tins - 15 kg/litre for ghee, vanaspati, edible oils and bakery shortenings - Specification (Second Revision)

- View breakup
Rs.3700/- (excluding Solder testing) and Rs.1500/- for solder testing.

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2.1 (Material)	-
4.1 (Dimensions and Tolerances)	-
4.2.2 (Handle)	-
4.2.1.1 (Dimensions and Tolerances )	-
4.3.4 (Manufacture)	-
4.3.5 (Handle)	-
5.1 (Air-Pressure Test)	-
5.2 (Handle Pull Test)	-
5.3 (Hydraulic Pressure Test)	-
4.2.1 (Material)	-
4.2.1 (Material)	-
4.3.1 (Manufacture)	-
4.3.2 (Manufacture)	-
4.3.3 (Manufacture)	-
4.3.4 (Manufacture)	-
4.3.5 (Handle)	-

-
Except Tin Content

Bureau of Indian Standards

The National Standards Body of India

Search by IS Number