BIS - LIMS (Laboratory Information Management System)

Search by IS Number

Reset

14026 Results

S.No.

Lab Name

Osl Code

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

1501

ALPHA TEST HOUSE PVT LTD, BAHADURGARH

8185306

IS 14968 (2015)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packing 50 Kg/25 kg sugar – Specification (first revision)

All

16900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(TYPES)	-	245	-
4.1(Raw Material)	-	245	-
4.2(Tapes – Width IS 6192 and IS 11197)	-	245	-
4.2(Tapes – Linear Density )	-	245	-
4.2(Construction)	-	245	-
4.3(Sacks)	-	245	-
4.3.1(Bottom Seam)	-	245	-
4.3.1(The two rows of stitches shall be separated from each other)	-	245	-
4.3.1( The outer stitch)	-	245	-
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	245	-
4.3.1(Stitches pass through a minimum of six layers of the fabric. )	-	245	-
4.3.1(stitches/dm)	-	245	-
4.3.2(Mouth)	-	245	-
4.4(Liner IS 10146 or IS 10910.)	-	245	-
4.4(Mass of the loose liner )	-	245	-
4.4(Width of the loose liner)	-	245	-
4.4(Length of the line)	-	245	-
4.4(Bottom seam of the loose liner)	-	245	-
4.4.1(Liner)	-	245	-
4.5 and Table 1 i(Capacity)	-	245	-
5.2 and Table 1 ii a(Dimensions Inside Length)	-	245	-
5.2 and Table 1 ii b(Dimensions Inside Width)	-	245	-
5.2 and Table 1 iii(Ends per dm )	-	245	-
5.2 and Table 1 iv(Picks per dm )	-	245	-
5.1 and Table 1 v a(Mass of unlaminated sack IS 1964)	-	245	-
5.1 and Table 1 v b(Mass of unlaminated sack with liner )	-	245	-
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise IS 1969 (Part 1))	-	245	-
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise IS 1969 (Part 1))	-	245	-
5.2 and Table 1 vi(Breaking strength of bottom seam IS 9030 )	-	245	-
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise IS 1969 (Part 1))	-	245	-
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise IS 1969 (Part 1))	-	245	-
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	245	-
5.2 and Table 1 x(Ash content )	-	245	-
3(TYPES)	-	245	-
4.1(Raw Material)	-	245	-
4.2(Tapes – Width IS 6192 and IS 11197)	-	245	-
4.2(Tapes – Linear Density )	-	245	-
4.2(Construction)	-	245	-
4.3(Sacks)	-	245	-
4.3.1(Bottom Seam)	-	245	-
4.3.1(The two rows of stitches shall be separated from each other)	-	245	-
4.3.1( The outer stitch)	-	245	-
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	245	-
4.3.1(Stitches pass through a minimum of six layers of the fabric. )	-	245	-
4.3.1(stitches/dm)	-	245	-
4.3.2(Mouth)	-	245	-
4.4(Liner IS 10146 or IS 10910.)	-	245	-
4.4(Mass of the loose liner )	-	245	-
4.4(Width of the loose liner)	-	245	-
4.4(Length of the line)	-	245	-
4.4(Bottom seam of the loose liner)	-	245	-
4.4.1(Liner)	-	245	-
4.5 and Table 1 i(Capacity)	-	245	-
5.2 and Table 1 ii a(Dimensions Inside Length)	-	245	-
5.2 and Table 1 ii b(Dimensions Inside Width)	-	245	-
5.2 and Table 1 iii(Ends per dm )	-	245	-
5.2 and Table 1 iv(Picks per dm )	-	245	-
5.1 and Table 1 v a(Mass of unlaminated sack IS 1964)	-	245	-
5.1 and Table 1 v b(Mass of unlaminated sack with liner )	-	245	-
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise IS 1969 (Part 1))	-	245	-
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise IS 1969 (Part 1))	-	245	-
5.2 and Table 1 vi(Breaking strength of bottom seam IS 9030 )	-	245	-
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise IS 1969 (Part 1))	-	245	-
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise IS 1969 (Part 1))	-	245	-
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	245	-
5.2 and Table 1 x(Ash content )	-	245	-
4.2 (Mesh size and weight in g/cm2) (amendment 3)(Mesh size and weight in g/cm2)	-	245	-
5.3(UV Resistance)	-	245	-
Cl-4.4 (Amendment-3)(Thickness of liner)	-	245	-

08 May, 2028

-
Included w.e.f 04.09.2025

1502

Gravitas Laboratories Private Limited, Greater Noida

8182606

IS 2002 (2024)

Steel Plate for Pressure Vessel for Intermediate and High Temperature Service Including Boilers â Specification (Fourth Revision)

All Grade

22500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(General requirements)	-	0	-
Cl-6(Manufacture)	-	0	-
Cl-7.1, Table-1(Carbon)	-	9000	-
Cl-7.1, Table-1(Manganese)	-	9000	-
Cl-7.1, Table-1(Silicon)	-	9000	-
Cl-7.1, Table-1(Sulphur)	-	9000	-
Cl-7.1, Table-1(Phosphorus)	-	9000	-
Cl-8(HEAT TREATMENT)	-	0	-
Cl-9(FREEDOM FROM DEFECTS)	-	1000	-
Cl-9.2.3(Repair by Welding)	-	0	-
Cl-10.2(Rolling Mass)	-	1000	-
Cl-11(CALCULATION OF MASS)	-	500	-
Cl-13(TENSILE TEST)	-	5500	-
Cl-13.2, Table-3(Tensile Strength)	-	5500	-
Cl-13.2, Table-3(Yield Stress)	-	5500	-
Cl-13.2, Table-3(Percent Elongation on Gauge Length)	-	5500	-
Cl-14(BEND TEST)	-	5500	-
Cl-16(ULTRASONIC TESTING)	-	0	If agreed additional charge 5500/-
Cl-18(RE-TEST)	-	0	-
Cl-19(RUST PROTECTIONS)	-	0	-
Cl-20(TOLERANCES ON DIMENSIONS AND SHAPE)	-	0	-
Cl-21(Marking)	-	0	-
Cl-4.1(General requirements)	-	0	-
Cl-6(Manufacture)	-	0	-
Cl-7.1, Table-1(Carbon)	-	0	-
Cl-7.1, Table-1(Manganese)	-	0	-
Cl-7.1, Table-1(Silicon)	-	0	-
Cl-7.1, Table-1(Sulphur)	-	0	-
Cl-7.1, Table-1(Phosphorus)	-	0	-
Cl-8(HEAT TREATMENT)	-	0	-
Cl-9(FREEDOM FROM DEFECTS)	-	0	-
Cl-9.2.3(Repair by Welding)	-	0	-
Cl-10.2(Rolling Mass)	-	0	-
Cl-11(CALCULATION OF MASS)	-	0	-
Cl-13(TENSILE TEST)	-	0	-
Cl-13.2, Table-3(Tensile Strength)	-	0	-
Cl-13.2, Table-3(Yield Stress)	-	0	-
Cl-13.2, Table-3(Percent Elongation on Gauge Length)	-	0	-
Cl-14(BEND TEST)	-	0	-
Cl-16(ULTRASONIC TESTING)	-	0	Same as above
Cl-18(RE-TEST)	-	0	-
Cl-19(RUST PROTECTIONS)	-	0	-
Cl-20(TOLERANCES ON DIMENSIONS AND SHAPE)	-	0	-
Cl-21(Marking)	-	0	-

19 Nov, 2027

-
Included w.e.f 08.12.2025

1503

Gravitas Laboratories Private Limited, Greater Noida

8182606

IS 2041 (2024)

Steel Plates and Strips for Pressure Vessels Used at Moderate and Low Temperature â Specification (Fourth Revision)

All Grade

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(General requirements)	-	0	-
Cl-6(MANUFACTURE)	-	0	-
Cl-7.1, Table-1(C)	-	9000	-
Cl-7.1, Table-1(Si)	-	9000	-
Cl-7.1, Table-1(Mn Max)	-	9000	-
Cl-7.1, Table-1(P max)	-	9000	-
Cl-7.1, Table-1(S Max)	-	9000	-
Cl-7.1, Table-1(Al Max)	-	9000	-
Cl-7.1, Table-1(N Max)	-	9000	-
Cl-7.1, Table-1(Nb Max)	-	9000	-
Cl-7.1, Table-1(V Max)	-	9000	-
Cl-7.1, Table-1(Ti Max)	-	9000	-
Cl-7.1, Table-1(Nb + V + Ti Max)	-	9000	-
Cl-7.1, Table-1(Cr Max)	-	9000	-
Cl-7.1, Table-1(Cu Max)	-	9000	-
Cl-7.1, Table-1(Mo Max)	-	9000	-
Cl-7.1, Table-1(Ni Max)	-	9000	-
Cl-7.2, Table-2(Carbon)	-	0	-
Cl-7.2, Table-2(Silicon)	-	0	-
Cl-7.2, Table-2(Manganese)	-	0	-
Cl-7.2, Table-2(Phosphorus)	-	0	-
Cl-7.2, Table-2(Sulphur)	-	0	-
Cl-7.2, Table-2(Niobium)	-	0	-
Cl-7.2, Table-2(Vanadium)	-	0	-
Cl-7.2, Table-2(Titanium)	-	0	-
Cl-7.2, Table-2(Chromium)	-	0	-
Cl-7.2, Table-2(Copper)	-	0	-
Cl-7.2, Table-2(Molybdenum)	-	0	-
Cl-7.2, Table-2(Nickel)	-	0	-
Cl-8(HEAT-TREATMENT)	-	0	-
Cl-9(FREEDOM FROM DEFECTS)	-	1000	-
Cl-9.3(Edge Imperfection)	-	1000	-
Cl-10(width ( average of 3))	-	1000	-
Cl-11(THEORETICAL MASS)	-	1000	-
Cl-12.1.1(Number of Tests)	-	0	-
Cl-12.1.2(Orientation of Test Sample)	-	0	-
Cl-12.1.3(Location of Test Sample)	-	0	-
Cl-12.1.6(Tensile Test Result)	-	5500	-
Cl-12.2(Bend Test)	-	1000	-
Cl-12.3.1(Charpy impact test)	-	5500	-
Cl-12.3.2(Number of Tests)	-	0	-
Cl-12.3.3(Orientation)	-	0	-
Cl-12.5(Re-heat Treatment)	-	0	-
Cl-13(ULTRASONIC TESTING)	-	0	-
Cl-14(RUST PROTECTION)	-	0	-
Cl-15(MARKING)	-	0	-
Cl-4.1(General requirements)	-	0	-
Cl-6(MANUFACTURE)	-	0	-
Cl-7.1, Table-1(C)	-	0	-
Cl-7.1, Table-1(Si)	-	0	-
Cl-7.1, Table-1(Mn Max)	-	0	-
Cl-7.1, Table-1(P max)	-	0	-
Cl-7.1, Table-1(S Max)	-	0	-
Cl-7.1, Table-1(Al Max)	-	0	-
Cl-7.1, Table-1(N Max)	-	0	-
Cl-7.1, Table-1(Nb Max)	-	0	-
Cl-7.1, Table-1(V Max)	-	0	-
Cl-7.1, Table-1(Ti Max)	-	0	-
Cl-7.1, Table-1(Nb + V + Ti Max)	-	0	-
Cl-7.1, Table-1(Cr Max)	-	0	-
Cl-7.1, Table-1(Cu Max)	-	0	-
Cl-7.1, Table-1(Mo Max)	-	0	-
Cl-7.1, Table-1(Ni Max)	-	0	-
Cl-7.2, Table-2(Carbon)	-	0	-
Cl-7.2, Table-2(Silicon)	-	0	-
Cl-7.2, Table-2(Manganese)	-	0	-
Cl-7.2, Table-2(Phosphorus)	-	0	-
Cl-7.2, Table-2(Sulphur)	-	0	-
Cl-7.2, Table-2(Niobium)	-	0	-
Cl-7.2, Table-2(Vanadium)	-	0	-
Cl-7.2, Table-2(Titanium)	-	0	-
Cl-7.2, Table-2(Chromium)	-	0	-
Cl-7.2, Table-2(Copper)	-	0	-
Cl-7.2, Table-2(Molybdenum)	-	0	-
Cl-7.2, Table-2(Nickel)	-	0	-
Cl-8(HEAT-TREATMENT)	-	0	-
Cl-9(FREEDOM FROM DEFECTS)	-	0	-
Cl-9.3(Edge Imperfection)	-	0	-
Cl-10(width ( average of 3))	-	0	-
Cl-11(THEORETICAL MASS)	-	0	-
Cl-12.1.1(Number of Tests)	-	0	-
Cl-12.1.2(Orientation of Test Sample)	-	0	-
Cl-12.1.3(Location of Test Sample)	-	0	-
Cl-12.1.6(Tensile Test Result)	-	0	-
Cl-12.2(Bend Test)	-	0	-
Cl-12.3.1(Charpy impact test)	-	0	-
Cl-12.3.2(Number of Tests)	-	0	-
Cl-12.3.3(Orientation)	-	0	-
Cl-12.5(Re-heat Treatment)	-	0	-
Cl-13(ULTRASONIC TESTING)	-	0	-
Cl-14(RUST PROTECTION)	-	0	-
Cl-15(MARKING)	-	0	-
CL 10(Thickness ( average 10 ))	-	0	-

19 Nov, 2027

-
Included w.e.f 13.11.2025

1504

Gravitas Laboratories Private Limited, Greater Noida

8182606

IS 5518 (1996)

Steels for die blocks for drop forging - Specification (Second Revision)

All Designation

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2(Molybdenum)	-	12000	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2(Nickel )	-	12000	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2(Chromium)	-	12000	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2(Phosphorus)	-	12000	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2(Sulphur)	-	12000	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2(Silicon)	-	12000	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2(Manganese)	-	12000	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2(Carbon)	-	12000	-
6(Freedom from defects)	-	12000	-
9(Hardness)	-	12000	-
12(Dimensional Tolerances)	-	12000	-
14(Ultasonic Test)	-	0	ON REQUEST 5500/-
16(Marking)	-	0	-
15(a) Macro etch test in accordance with IS 11371 : 1985; b) Cleanliness test as per IS 10138 (Part 1) : 1992, IS 10138 (Part 2) : 1983 and IS 10138 (Part 3) : 1983; and c) Distribution of carbides as per IS 12211 : 1987.)	-	12000	-
6(Freedom from defects)	-	0	-
9(Hardness)	-	0	-
12(Dimensional Tolerances)	-	0	-
14(Ultasonic Test)	-	0	-
16(Marking)	-	0	-
15(a) Macro etch test in accordance with IS 11371 : 1985; b) Cleanliness test as per IS 10138 (Part 1) : 1992, IS 10138 (Part 2) : 1983 and IS 10138 (Part 3) : 1983; and c) Distribution of carbides as per IS 12211 : 1987.)	-	0	-
"Clause 7.1 to 7.3 and 11.1 Table 1 T55Ni7Cr4Mo5VI T55Ni7Cr3Mo3VI"(Vanadium)	-	0	-
Clause 12(Dimension Tolerance)	-	0	-
Clause 14(Ultrasonic Testing)	-	0	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2(Molybdenum)	-	0	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2(Nickel )	-	0	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2(Chromium)	-	0	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2(Phosphorus)	-	0	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2(Sulphur)	-	0	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2(Silicon)	-	0	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2(Manganese)	-	0	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2(Carbon)	-	0	-
6(Freedom from defects)	-	0	-
9(Hardness)	-	0	-
12(Dimensional Tolerances)	-	0	-
14(Ultasonic Test)	-	0	-
16(Marking)	-	0	-
15(a) Macro etch test in accordance with IS 11371 : 1985; b) Cleanliness test as per IS 10138 (Part 1) : 1992, IS 10138 (Part 2) : 1983 and IS 10138 (Part 3) : 1983; and c) Distribution of carbides as per IS 12211 : 1987.)	-	0	-
6(Freedom from defects)	-	0	-
9(Hardness)	-	0	-
12(Dimensional Tolerances)	-	0	-
14(Ultasonic Test)	-	0	-
16(Marking)	-	0	-
15(a) Macro etch test in accordance with IS 11371 : 1985; b) Cleanliness test as per IS 10138 (Part 1) : 1992, IS 10138 (Part 2) : 1983 and IS 10138 (Part 3) : 1983; and c) Distribution of carbides as per IS 12211 : 1987.)	-	0	-
"Clause 7.1 to 7.3 and 11.1 Table 1 T55Ni7Cr4Mo5VI T55Ni7Cr3Mo3VI"(Vanadium)	-	0	-
Clause 12(Dimension Tolerance)	-	0	-
Clause 14(Ultrasonic Testing)	-	0	-

19 Nov, 2027

-
Included w.e.f 13.11.2025

1505

Bharat Test House Pvt Ltd 1474 Sonipat Haryana

9135626

IS/IEC 61730 : PART 2 (2023)

Photovoltaic (PV) Module - Safety Qualification Part 2 Requirements for Testing (Second Revision)

Photovoltaic (PV) Module

823500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.2(Visual inspection MST 01)	-	7500	-
10.3(Performance at STC MST 02)	-	7500	-
10.4(Maximum power determination MST 03)	-	12500	-
10.5(Insulation thickness test MST 04)	-	12000	-
10.6(Durability of markings MST 05)	-	12000	-
10.7(Sharp edge test MST 06)	-	15000	-
10.8(Bypass diode functionality test MST 07)	-	15000	-
10.9(Accessibility test MST 11)	-	15000	-
10.1(Cut susceptibility test MST 12)	-	15000	-
10.11(Continuity test of equipotential bonding MST 13)	-	20000	-
10.12(Impulse voltage test MST 14)	-	22500	-
10.13(Insulation test MST 16)	-	25000	-
10.14(Wet leakage current test MST 17)	-	15000	-
10.16(Hot-spot endurance test MST 22)	-	22500	-
10.17(Fire test MST 23)	-	175000	-
10.18(Ignitability test MST 24)	-	12500	-
10.19(Bypass diode thermal test MST 25)	-	12500	-
10.20(Reverse current overload test MST 26)	-	55000	-
10.21(Module breakage test MST 32)	-	27500	-
10.22(Screw connections test MST 33)	-	32500	-
10.23(Static mechanical load test MST 34)	-	12500	-
10.24(Peel test MST 35)	-	12500	-
10.25(Lap shear strength test MST 36)	-	5000	-
10.26(Materials creep test MST 37)	-	12500	-
10.27(Robustness of terminations test MST 42)	-	12500	-
10.28(Thermal cycling test MST 51)	-	17500	-
10.29(Humidity freeze test MST 52)	-	55000	-
10.30(Damp heat test MST 53)	-	40000	-
10.31(UV test MST 54)	-	27500	-
10.32(Cold conditioning test MST 55)	-	40000	-
10.33(Dry heat conditioning test MST 56)	-	30000	-
10.34(Evaluation of insulation coordination MST 57)	-	30000	-

19 Mar, 2026

-
Included w.e.f.03.09.2025

1506

ADS LABTECH, GHAZIABAD

8178326

IS 17425 (2020)

Irrigation Equipment - Quick Coupled Polyethylene Pipes and Fittings for Sprinkler Irrigation Systems - Specification

Irrigation Equipment - Quick Coupled Polyethylene Pipes and Fittings for Sprinkler Irrigation Systems

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.3(Anti-oxidant)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Aluminium Content)	-	4000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Copper Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Magnesium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Silicon Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Iron Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Manganese Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Zinc Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Titanium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Chromium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Remarks)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Aluminium Content)	-	4000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Copper Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Magnesium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Silicon Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Iron Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Manganese Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Zinc Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Titanium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Chromium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Remarks)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Aluminium Content)	-	4000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Copper Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Magnesium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Silicon Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Iron Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Manganese Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Zinc Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Titanium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Chromium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Remarks)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Aluminium Content)	-	4000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Copper Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Magnesium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Silicon Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Iron Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Manganese Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Zinc Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Titanium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Chromium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Remarks)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Aluminium Content)	-	4000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Copper Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Magnesium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Silicon Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Iron Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Manganese Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Zinc Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Titanium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Chromium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Cr + Mn)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Aluminium Content)	-	4000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Copper Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Magnesium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Silicon Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Iron Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Manganese Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Zinc Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Titanium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Chromium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Cr + Mn)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Aluminium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Copper Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Magnesium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Silicon Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Iron Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Manganese Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Zinc Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Titanium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Chromium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Cr + Mn)	-	1000	-
5(Dimensions of pipe - i) Outside diameter)	-	500	-
5(Dimensions of pipe - ii) Wall thickness minimum)	-	500	-
6(Visual Appearance)	-	200	-
7.1(Hydraulic Characteristics - Quality test)	-	2000	-
7.1(Hydraulic Characteristics - Acceptance test)	-	2000	-
7.2(Reversion Test)	-	500	-
7.3(Tensile Test- i) Tensile Strength)	-	2000	-
7.3(Tensile Test - ii)Elongation at Break)	-	2000	-
7.4(Fusion Compatibility Test- a) Quality test)	-	2000	-
7.4(Fusion Compatibility Test- b) Acceptance test)	-	2000	-
7.5(Density)	-	500	-
7.6(Melt Flow Rate)	-	1000	-
7.6(Melt Flow Rate)	-	1000	-
4.2(Carbon black- a)carbon content)	-	1000	-
4.2(Carbon black- b) Dispersion of carbon black)	-	1000	-
7.6(Melt now Rate (MFR))	-	10005	-
7.5(Density)	-	500	-
7.4 Table-2(Fusion Compatibility Test)	-	2000	-
7.3(Tensile Test)	-	2000	-
7.2(Reversion Test)	-	500	-
7.1 Table -2(Hydraulic Characteristics)	-	2000	-
6.1(VISUAL APPEARANCE)	-	200	-
5.1.2(Ovality)	-	200	-
5.1 table -1(DIMENSIONS OF PIPES)	-	200	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Copper Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Silicon Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Magnesium Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Iron Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Manganese Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Nickel Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Zinc Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Lead Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Tin Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Titanium Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Aluminium Content)	-	1000	-
Cl. 4.2 , IS 2530-1963, Cl. 10(Cabon Black Content)	-	1000	-
4.1.2(The MFR of the material shall be between 0.2 to 1.1 (both inclusive) when tested at 190 T at a nominal load of 50 N by the method prescribed in 7 of IS 2530. The MFR of the material shall also be within 20% of the value declared by the manufacturer.’)	-	1000	-
4.1.1(density shall be between 940.4 kg/m’ and 958.4 kg/m3 (both inclusive) when determined at 27°C according to procedure prescribed in Annex A of IS 7328. The value of the density shall also not differ from the nominal value by more than 3 kg/m2 as per 5.2.1.1 of IS 7328.)	-	500	-
4.1(melt flow rating (MFR) shall not exceed 1.10 g/10 min.)	-	1000	-
3(CLASSIFICATION OF PIPES)	-	200	-
4.1(Quick Coupled Male and Female Couplers)	-	200	-
4.1(Quick Coupled Male and Female Couplers)	-	500	-
4.1.3(Workmanship and appearance)	-	200	-
4.1.4(Holding attachments for coupler parts)	-	5000	-
6.1.3(Weldability Test- a) Quality test)	-	2000	-
6.1.3(Weldability Test- b) Acceptance test)	-	2000	-
3(Quick Coupled pipes)	-	200	-
3(QUICK COUPLED PIPES)	-	200	-
4(QUICK COUPLED FITTINGS)	-	200	-
4.1 (a)(Quick Coupled Male and Female Couplers)	-	200	-
4.1 (b)(HDPE couplers —)	-	200	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Carbon Content)	-	200	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Manganese Content)	-	1000	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Sulphur Content)	-	1000	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Phosphorous Content)	-	1000	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Al-Killed(Aluminium Content)	-	1000	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Si-Killed(Silicon Content)	-	1000	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Al-Si-Killed(Silicon Content)	-	1000	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Al-Si-Killed(Aluminium Content)	-	1000	-
Cl.4.1.3, T-1(Volatile Matter)	-	1000	-
Cl.4.1.3, T-1(Volatile Matter)	-	1000	-
Cl.4.1.3, T-1(Volatile Matter)	-	1000	-
Cl.4.1.3, T-1(Volatile Matter)	-	1000	-
Cl.4.1.3, T-1(Volatile Matter)	-	1000	-
Cl.4.1.3, T-1(Volatile Matter)	-	1000	-
Cl.4.1.3, T-1(Volatile Matter)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl. 4.1.1.2.1, IS 14151 (P-1)-1999, Cl. 4, IS 2530-1963, Cl. 10(Cabon Black Content)	-	1000	-
Cl. 4.1.1.2.1, IS 14151 (P-1)-1999, Cl. 4, IS 2530-1963, Cl. 16(Carbon Black Dispersion)	-	1000	-
4.1 .1.2.1(HDPE couplers)	-	1000	-
4.1 .1.2.2(HDPE couplers)	-	1000	-
4.1.4(a)(Holding Attachments for Coupler Parts)	-	1000	-
4.1.4(b)(Holding Attachments for Coupler Parts)	-	1000	-
4.2.1(Quick Coupled ~pe HDPE Fittings)	-	1000	-
4.2.2(Quick Coupled ~pe HDPE Fittings)	-	1000	-
4.2.3(Quick Coupled ~pe HDPE Fittings)	-	1000	-
4.2.4(Quick Coupled ~pe HDPE Fittings)	-	1000	-
4.2.5(Quick Coupled ~pe HDPE Fittings)	-	1000	-
4.2.6(Quick Coupled ~pe HDPE Fittings)	-	1000	-
4.2.7(Quick Coupled ~pe HDPE Fittings)	-	1000	-
4.2.7(1 Dimensions of Quick Coupled Pipes and Fittings)	-	1000	-
4.2.7(Reducers Table 1 and 2 of IS 8008 (Part 4))	-	1000	-
4.2.7(Ferrule reducers Table 1 of IS 8008 (Part 5))	-	1000	-
4.2.7(Pipe ends Table 1 of IS 8008 (Part 6))	-	1000	-
4.2.7(End caps Table 1 of IS 8008 (Part 9))	-	1000	-
4.2.7(Insert vatve couplers Table 1 of IS 8008 (Part 3))	-	1000	-
4.2.7(Valve openers Table 1 of IS 8008 (Part 2))	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
6.1(Volatile Matter)	-	1000	-
6.1(Water content)	-	1000	-
6.2.1(Volatile Matter x 2)	-	1000	-
6.2.1(Water content x 2)	-	1000	-
4.1.1 (Table-1)(Volatile Matter)	-	1000	-
4.1.1 (Table-1)(Water content)	-	1000	-
4.1.3, Table 1,(iv)(Volatile matter)	-	1000	-
4.1.3, Table 1,(v)(Water content)	-	1000	-
5.2(Dimensions of Quick Coupled Sprinkler Saddles Table 1.)	-	500	-
6.1(Quick Coupled Pipes and Fittings)	-	1000	-
6.1.1, 6.1.1.1(Leakage Test)	-	2000	-
6.1.1, 6.1.1.1(Leakage Test)	-	2000	-
6.1.2, 6.1.2.1(Hydraulic Proof Test)	-	2000	-
6.1.2.2(Hydraulic Proof Test)	-	2000	-
6.1.2.2(Hydraulic Proof Test)	-	2000	-
6.1.3, 6.1.3.1(Weldability Test)	-	2000	-
6.1.3.1.1(Weldability Test)	-	2000	-
6.1.3.2(Quick coupled fittings)	-	2000	-
6.2, 6.2.1(Quick Coupled Fittings)	-	2000	-
7.2.1(Visual and Workmanship Requirement)	-	200	-
6.2 b(Material Identification - Male & Female Coupler)	-	500	-
6.3.3(Material Identification - Insert Valve Coupler)	-	500	-
6.3.3(Material Identification - Insert Valve Coupler)	-	500	-
6.3.4()	-	500	-
6.3.5(Material Identification - Saddle)	-	500	-
6.3.5(Material Identification - Pipe Ends)	-	500	-
6.3.6(Quick Coupled Pump Connectors - Visual)	-	500	-
4.2(Metallic Couplers)	-	500	-
4.2(Metallic Couplers)	-	500	-
7.2.1(Leakage Test)	-	2000	-
Cl.4.1.3(Den sity Test)	-	500	-
Cl.4.1.3(MFR Test)	-	1000	-
Cl.4.1.3(MFR Test)	-	1000	-
Cl.4.1.3(MFR Test)	-	1000	-
Cl.4.1.3(MFR Test)	-	1000	-
Cl.4.1.3(Thermal Stabi lity)	-	1000	-
Cl.4.1.3(Thermal Stabi lity)	-	1000	-
Cl.7.1.7(MFR Test)	-	1000	-
Cl.7.1.7(MFR Test)	-	1000	-
Cl.7.1.7(MFR Test)	-	1000	-
Cl.7.1.7(MFR Test)	-	1000	-
Cl.4.1.4(Carbon Black Content)	-	1000	-
Cl.4.1.4(Carbon Black Content)	-	1000	-
Cl.4.1.4(Carbon Black Content)	-	1000	-
Cl.4.1.4(Carbon Black Di spersion)	-	1000	-
Cl.4.1.4(Carbon Black Di spersion)	-	1000	-
Cl.4.1.4(Carbon Black Di spersion)	-	1000	-
Cl.7.1.3(Reversion Test)	-	1000	-
Cl.7.1.3(Reversion Test)	-	1000	-
Cl.7.2.l(Leakage Test)	-	2000	-
Cl.7.2.l(Leakage Test)	-	2000	-
Cl.7.2.l(Leakage Test)	-	2000	-
Cl.7.2.l(Leakage Test)	-	2000	-
Cl.7.2.l(Leakage Test)	-	2000	-
6.1(Thermal Stability (OIT))	-	2000	-
6.1(Carbon Black Content)	-	1000	-
6.1(Carbon Black Dispersion)	-	1000	-
6.2.1(Melt Flow Index x 2)	-	1000	-
6.2.1(Thermal Stability (OIT) x 2)	-	1000	-
6.2.1(Carbon Black Content x 2)	-	1000	-
6.2.1(Carbon Black Dispersion x 2)	-	1000	-
7.1.3(Reversion)	-	500	-
6.2.5(Material Composition (Chemical Analysis))	-	1000	-
4.2.2(Coating thickness (Hot dip Galvanized or Electroplated or Passivated or Powder Coated))	-	1000	-
Cl.5(Di men sion)	-	500	-
Cl.5.1.l(Outside Diameter)	-	500	-
Cl.5.1.l(Outside Diameter)	-	500	-
Cl.6.2.L(Wall Thickness)	-	500	-
Cl.6.2.4(Workmanship and Appearance)	-	500	-
Cl.6.2.6(Rubber Ring Hardness)	-	500	-
Cl.6.2.6(Ageing Test)	-	500	-
Cl.7.1.l(Visual Anneara nce)	-	500	-
Cl.7.1.2(Hydraulic Characteristic)	-	2000	-
Cl.7.1.2(Hydraulic Characteristic)	-	2000	-
Cl.7.1.2(Hydraulic Characteristic)	-	2000	-
Cl.7.1.2(Hydraulic Characteristic)	-	2000	-
7.1.6(Carbon black Content)	-	1000	-
7.1.7(Melt Flow Rate (MFR))	-	1000	-
7.2.1(Leakage test 1hour / 27°C)	-	2000	-
7.2.2(Hydraulic Proof test 1hour / 27°C)	-	2000	-
4.1.1 (Table-1)(Melt Flow Index)	-	1000	-
4.1.1 (Table-1)(Oxidation Induction Time)	-	2000	-
4.1.4(Carbon Black Content)	-	1000	-
4.1.4(Carbon Black Dispersion)	-	1000	-
4.1.1(Polyethylene material)	-	1000	-
4.1.3, Table 1,(ii)(Melt flow rate)	-	1000	-
4.1.3, Table 1,(iii)(Thermal stability)	-	1000	-
Cl.7.1.4(Tensile Test)	-	2000	-
Cl.7.1.4(Tensile Test)	-	2000	-
Cl.7.1.4(Tensile Test)	-	2000	-
Cl.7.1.4(Elongation)	-	2000	-
Cl.7.1.4(Elongation)	-	2000	-
Cl.7.1.5(Fusion Compatibility)	-	2000	-
Cl.7.1.5(Fusion Compatibility)	-	2000	-
Cl.7.1.5(Fusion Compatibility)	-	2000	-
Cl.7.1.5(Fusion Compatibility)	-	2000	-
Cl.7.1.6(Corrected Density)	-	500	-
4.1.4(The Carbon Content and Dispersion)	-	1000	-
4.1.5(Carbon Black Specification)	-	1000	-
4.1.6(Antioxidant)	-	1000	-
7.1.3(Reversion Test)	-	500	-
Cl.7.2.2(Cl.7.2.2)	-	1000	-
Cl.7.2.3(Weld ability Test)	-	1000	-
Cl.7.2.3(Weld ability Test)	-	2000	-
6.2 (iii) Rubber Rings (a) Shore hardness(Shore hardness)	-	2000	-
6.2 (iii) Rubber Rings (b) Accelerated Storage test(Accelerated Storage test)	-	200	-
5(Dimensions of pipe (outside diameter, ovality, wall thickness))	-	500	-
6.1(Tensile strength at Yield & Elongation at break)	-	2000	-
6.2.1(Base Density x 2)	-	500	-
7.1.7(Melt flow rate)	-	1000	-
7.2.1(Leakage Test)	-	2000	-
7.2.2(Hydraulic Proof Test)	-	2000	-
7.2.3(Weldability Test)	-	2000	-
6.2.1(Wall thickness of male & female coupler)	-	500	-
6.2.4(Workmanship and appearance (Visual))	-	200	-
6.2.5(Holding attachment for coupler parts)	-	5000	-
7.3(Quick Couple Fitting)	-	200	-
10(Marking)	-	200	-
5.1.2(Squareness)	-	200	-
Cl 6.3.5, Table 5 Dimension of Quick Coupled Sprinkler Saddles (Foot Batten)(Table 5 Dimension of Quick Coupled Sprinkler Saddles (Foot Batten))	-	500	-
7.1.4(Tensile Test)	-	2000	-
7.1.5(Fusion Compatibility Test)	-	2000	-
6.2.6(Material Identification (Chemical Analysis))	-	200	-
6.2.6(Color)	-	200	-
6.2.6(Rubber Ring Hardness Shore – A (Before Ageing))	-	500	-
6.2.6(Ageing Charges for rubber ring)	-	500	-
7.1.1(Visual appearance of pipes)	-	200	-
7.1.2(Hydraulic Characteristics)	-	2000	-
7.1.2((a) Acceptance Test (48 hrs) / 80˚ C)	-	2000	..
7.1.2((b) Type test ( 165 hrs) / 80˚ C)	-	2000	.
7.1.4(Tensile strength & elongation)	-	2000	.
7.1.5(Fusion Compatibility test)	-	2000	.
7.1.5((a) Acceptance Test (48 hrs) / 80˚ C)	-	2000	.
7.1.5((b) Type test ( 165 hrs) / 80˚ C)	-	2000	.
7.1.6(Corrected Density)	-	500	.
7.1.6(Base Density)	-	500	.
7.2.3((a) Acceptance Test (48 hrs) / 80˚ C)	-	2000	.
7.2.3((b) Type test ( 165 hrs) / 80˚ C)	-	2000	.
8(Supply of pipe (Visual))	-	200	.
4.1.1 (Table-1)(Density)	-	500	.
4.1.1 (Table-1)(Tensile strength at Yield & Elongation at break)	-	2000	.
4.1.3, Table 1,(i)(Bass density)	-	500	.
4.1.3, Table 1,(vi)(Minimum tensile strength at yield)	-	2000	.
4.1.3, Table 1,(vii)(Minimum elongation at break)	-	2000	.
4.1.7(Rework Material)	-	500	.
4.2(Metallic Couplers)	-	500	.
5.1, Table 1,(i)(Plain pipes)	-	500	.
5.1, Table 1,(ii)(90° Bends and tee)	-	500	.
5.1, Table 1,(iii)(Base pipe )	-	500	.
5.1, Table 1,(iv)(PCN)	-	500	.
5.1, Table 1,(v)(Reducers, ferrule reducers)	-	500	.
5.1, Table 1,(vi)(End caps, insert valve coupler, valve openers)	-	500	.
5.1, Table 1,(vii)(Riser pipe and socket)	-	500	.
7.1.1(Visual Appearance and Workmanship)	-	500	.
7.1.2(Hydraulic Performance Characteristic)	-	2000	..
7.1.6(Corrected Density)	-	500	.
4.3(Anti-oxidant)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Aluminium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Copper Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Magnesium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Silicon Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Iron Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Manganese Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Zinc Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Titanium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Chromium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Remarks)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Aluminium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Copper Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Magnesium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Silicon Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Iron Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Manganese Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Zinc Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Titanium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Chromium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Remarks)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Aluminium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Copper Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Magnesium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Silicon Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Iron Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Manganese Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Zinc Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Titanium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Chromium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Remarks)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Aluminium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Copper Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Magnesium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Silicon Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Iron Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Manganese Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Zinc Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Titanium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Chromium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Remarks)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Aluminium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Copper Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Magnesium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Silicon Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Iron Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Manganese Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Zinc Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Titanium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Chromium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Cr + Mn)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Aluminium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Copper Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Magnesium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Silicon Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Iron Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Manganese Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Zinc Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Titanium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Chromium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Cr + Mn)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Aluminium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Copper Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Magnesium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Silicon Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Iron Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Manganese Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Zinc Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Titanium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Chromium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Cr + Mn)	-	1000	-
5(Dimensions of pipe - i) Outside diameter)	-	1000	-
5(Dimensions of pipe - ii) Wall thickness minimum)	-	1000	-
6(Visual Appearance)	-	1000	-
7.1(Hydraulic Characteristics - Quality test)	-	1000	-
7.1(Hydraulic Characteristics - Acceptance test)	-	1000	-
7.2(Reversion Test)	-	1000	-
7.3(Tensile Test- i) Tensile Strength)	-	1000	-
7.3(Tensile Test - ii)Elongation at Break)	-	1000	-
7.4(Fusion Compatibility Test- a) Quality test)	-	1000	-
7.4(Fusion Compatibility Test- b) Acceptance test)	-	1000	-
7.5(Density)	-	1000	-
7.6(Melt Flow Rate)	-	1000	-
7.6(Melt Flow Rate)	-	1000	-
4.2(Carbon black- a)carbon content)	-	1000	-
4.2(Carbon black- b) Dispersion of carbon black)	-	1000	-
7.6(Melt now Rate (MFR))	-	1000	-
7.5(Density)	-	1000	-
7.4 Table-2(Fusion Compatibility Test)	-	1000	-
7.3(Tensile Test)	-	1000	-
7.2(Reversion Test)	-	1000	-
7.1 Table -2(Hydraulic Characteristics)	-	1000	-
6.1(VISUAL APPEARANCE)	-	1000	-
5.1.2(Ovality)	-	1000	-
5.1 table -1(DIMENSIONS OF PIPES)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Copper Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Silicon Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Magnesium Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Iron Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Manganese Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Nickel Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Zinc Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Lead Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Tin Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Titanium Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Aluminium Content)	-	1000	-
Cl. 4.2 , IS 2530-1963, Cl. 10(Cabon Black Content)	-	1000	-
4.1.2(The MFR of the material shall be between 0.2 to 1.1 (both inclusive) when tested at 190 T at a nominal load of 50 N by the method prescribed in 7 of IS 2530. The MFR of the material shall also be within 20% of the value declared by the manufacturer.’)	-	1000	-
4.1.1(density shall be between 940.4 kg/m’ and 958.4 kg/m3 (both inclusive) when determined at 27°C according to procedure prescribed in Annex A of IS 7328. The value of the density shall also not differ from the nominal value by more than 3 kg/m2 as per 5.2.1.1 of IS 7328.)	-	1000	-
4.1(melt flow rating (MFR) shall not exceed 1.10 g/10 min.)	-	1000	-
3(CLASSIFICATION OF PIPES)	-	1000	-
4.1(Quick Coupled Male and Female Couplers)	-	1000	-
4.1(Quick Coupled Male and Female Couplers)	-	1000	-
4.1.3(Workmanship and appearance)	-	1000	-
4.1.4(Holding attachments for coupler parts)	-	1000	-
6.1.3(Weldability Test- a) Quality test)	-	1000	-
6.1.3(Weldability Test- b) Acceptance test)	-	1000	-
3(Quick Coupled pipes)	-	1000	-
3(QUICK COUPLED PIPES)	-	1000	-
4(QUICK COUPLED FITTINGS)	-	1000	-
4.1 (a)(Quick Coupled Male and Female Couplers)	-	1000	-
4.1 (b)(HDPE couplers —)	-	1000	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Carbon Content)	-	1000	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Manganese Content)	-	1000	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Sulphur Content)	-	1000	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Phosphorous Content)	-	1000	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Al-Killed(Aluminium Content)	-	1000	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Si-Killed(Silicon Content)	-	1000	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Al-Si-Killed(Silicon Content)	-	1000	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Al-Si-Killed(Aluminium Content)	-	1000	-
Cl.4.1.3, T-1(Volatile Matter)	-	1000	-
Cl.4.1.3, T-1(Volatile Matter)	-	1000	-
Cl.4.1.3, T-1(Volatile Matter)	-	1000	-
Cl.4.1.3, T-1(Volatile Matter)	-	1000	-
Cl.4.1.3, T-1(Volatile Matter)	-	1000	-
Cl.4.1.3, T-1(Volatile Matter)	-	1000	-
Cl.4.1.3, T-1(Volatile Matter)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl. 4.1.1.2.1, IS 14151 (P-1)-1999, Cl. 4, IS 2530-1963, Cl. 10(Cabon Black Content)	-	1000	-
Cl. 4.1.1.2.1, IS 14151 (P-1)-1999, Cl. 4, IS 2530-1963, Cl. 16(Carbon Black Dispersion)	-	1000	-
4.1 .1.2.1(HDPE couplers)	-	1000	-
4.1 .1.2.2(HDPE couplers)	-	1000	-
4.1.4(a)(Holding Attachments for Coupler Parts)	-	1000	-
4.1.4(b)(Holding Attachments for Coupler Parts)	-	1000	-
4.2.1(Quick Coupled ~pe HDPE Fittings)	-	1000	-
4.2.2(Quick Coupled ~pe HDPE Fittings)	-	1000	-
4.2.3(Quick Coupled ~pe HDPE Fittings)	-	1000	-
4.2.4(Quick Coupled ~pe HDPE Fittings)	-	1000	-
4.2.5(Quick Coupled ~pe HDPE Fittings)	-	1000	-
4.2.6(Quick Coupled ~pe HDPE Fittings)	-	1000	-
4.2.7(Quick Coupled ~pe HDPE Fittings)	-	1000	-
4.2.7(1 Dimensions of Quick Coupled Pipes and Fittings)	-	1000	-
4.2.7(Reducers Table 1 and 2 of IS 8008 (Part 4))	-	1000	-
4.2.7(Ferrule reducers Table 1 of IS 8008 (Part 5))	-	1000	-
4.2.7(Pipe ends Table 1 of IS 8008 (Part 6))	-	1000	-
4.2.7(End caps Table 1 of IS 8008 (Part 9))	-	1000	-
4.2.7(Insert vatve couplers Table 1 of IS 8008 (Part 3))	-	1000	-
4.2.7(Valve openers Table 1 of IS 8008 (Part 2))	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
6.1(Volatile Matter)	-	1000	-
6.1(Water content)	-	1000	-
6.2.1(Volatile Matter x 2)	-	1000	-
6.2.1(Water content x 2)	-	1000	-
4.1.1 (Table-1)(Volatile Matter)	-	1000	-
4.1.1 (Table-1)(Water content)	-	1000	-
4.1.3, Table 1,(iv)(Volatile matter)	-	1000	-
4.1.3, Table 1,(v)(Water content)	-	1000	-
5.2(Dimensions of Quick Coupled Sprinkler Saddles Table 1.)	-	1000	-
6.1(Quick Coupled Pipes and Fittings)	-	1000	-
6.1.1, 6.1.1.1(Leakage Test)	-	1000	-
6.1.1, 6.1.1.1(Leakage Test)	-	1000	-
6.1.2, 6.1.2.1(Hydraulic Proof Test)	-	1000	-
6.1.2.2(Hydraulic Proof Test)	-	1000	-
6.1.2.2(Hydraulic Proof Test)	-	1000	-
6.1.3, 6.1.3.1(Weldability Test)	-	1000	-
6.1.3.1.1(Weldability Test)	-	1000	-
6.1.3.2(Quick coupled fittings)	-	1000	-
6.2, 6.2.1(Quick Coupled Fittings)	-	1000	-
7.2.1(Visual and Workmanship Requirement)	-	1000	-
6.2 b(Material Identification - Male & Female Coupler)	-	1000	-
6.3.3(Material Identification - Insert Valve Coupler)	-	1000	-
6.3.3(Material Identification - Insert Valve Coupler)	-	1000	-
6.3.4()	-	1000	-
6.3.5(Material Identification - Saddle)	-	1000	-
6.3.5(Material Identification - Pipe Ends)	-	1000	-
6.3.6(Quick Coupled Pump Connectors - Visual)	-	1000	-
4.2(Metallic Couplers)	-	1000	-
4.2(Metallic Couplers)	-	1000	-
7.2.1(Leakage Test)	-	1000	-
Cl.4.1.3(Den sity Test)	-	1000	-
Cl.4.1.3(MFR Test)	-	1000	-
Cl.4.1.3(MFR Test)	-	1000	-
Cl.4.1.3(MFR Test)	-	1000	-
Cl.4.1.3(MFR Test)	-	1000	-
Cl.4.1.3(Thermal Stabi lity)	-	1000	-
Cl.4.1.3(Thermal Stabi lity)	-	1000	-
Cl.7.1.7(MFR Test)	-	1000	-
Cl.7.1.7(MFR Test)	-	1000	-
Cl.7.1.7(MFR Test)	-	1000	-
Cl.7.1.7(MFR Test)	-	1000	-
Cl.4.1.4(Carbon Black Content)	-	1000	-
Cl.4.1.4(Carbon Black Content)	-	1000	-
Cl.4.1.4(Carbon Black Content)	-	1000	-
Cl.4.1.4(Carbon Black Di spersion)	-	1000	-
Cl.4.1.4(Carbon Black Di spersion)	-	1000	-
Cl.4.1.4(Carbon Black Di spersion)	-	1000	-
Cl.7.1.3(Reversion Test)	-	1000	-
Cl.7.1.3(Reversion Test)	-	1000	-
Cl.7.2.l(Leakage Test)	-	1000	-
Cl.7.2.l(Leakage Test)	-	1000	-
Cl.7.2.l(Leakage Test)	-	1000	-
Cl.7.2.l(Leakage Test)	-	1000	-
Cl.7.2.l(Leakage Test)	-	1000	-
6.1(Thermal Stability (OIT))	-	1000	-
6.1(Carbon Black Content)	-	1000	-
6.1(Carbon Black Dispersion)	-	1000	-
6.2.1(Melt Flow Index x 2)	-	1000	-
6.2.1(Thermal Stability (OIT) x 2)	-	1000	-
6.2.1(Carbon Black Content x 2)	-	1000	-
6.2.1(Carbon Black Dispersion x 2)	-	1000	-
7.1.3(Reversion)	-	1000	-
6.2.5(Material Composition (Chemical Analysis))	-	1000	-
4.2.2(Coating thickness (Hot dip Galvanized or Electroplated or Passivated or Powder Coated))	-	1000	-
Cl.5(Di men sion)	-	1000	-
Cl.5.1.l(Outside Diameter)	-	1000	-
Cl.5.1.l(Outside Diameter)	-	1000	-
Cl.6.2.L(Wall Thickness)	-	1000	-
Cl.6.2.4(Workmanship and Appearance)	-	1000	-
Cl.6.2.6(Rubber Ring Hardness)	-	1000	-
Cl.6.2.6(Ageing Test)	-	1000	-
Cl.7.1.l(Visual Anneara nce)	-	1000	-
Cl.7.1.2(Hydraulic Characteristic)	-	1000	-
Cl.7.1.2(Hydraulic Characteristic)	-	1000	-
Cl.7.1.2(Hydraulic Characteristic)	-	1000	-
Cl.7.1.2(Hydraulic Characteristic)	-	1000	-
7.1.6(Carbon black Content)	-	1000	-
7.1.7(Melt Flow Rate (MFR))	-	1000	-
7.2.1(Leakage test 1hour / 27°C)	-	1000	-
7.2.2(Hydraulic Proof test 1hour / 27°C)	-	1000	-
4.1.1 (Table-1)(Melt Flow Index)	-	1000	-
4.1.1 (Table-1)(Oxidation Induction Time)	-	1000	-
4.1.4(Carbon Black Content)	-	1000	-
4.1.4(Carbon Black Dispersion)	-	1000	-
4.1.1(Polyethylene material)	-	1000	-
4.1.3, Table 1,(ii)(Melt flow rate)	-	1000	-
4.1.3, Table 1,(iii)(Thermal stability)	-	1000	-
Cl.7.1.4(Tensile Test)	-	1000	-
Cl.7.1.4(Tensile Test)	-	1000	-
Cl.7.1.4(Tensile Test)	-	1000	-
Cl.7.1.4(Elongation)	-	1000	-
Cl.7.1.4(Elongation)	-	1000	-
Cl.7.1.5(Fusion Compatibility)	-	1000	-
Cl.7.1.5(Fusion Compatibility)	-	1000	-
Cl.7.1.5(Fusion Compatibility)	-	1000	-
Cl.7.1.5(Fusion Compatibility)	-	1000	-
Cl.7.1.6(Corrected Density)	-	1000	-
4.1.4(The Carbon Content and Dispersion)	-	1000	-
4.1.5(Carbon Black Specification)	-	1000	-
4.1.6(Antioxidant)	-	1000	-
7.1.3(Reversion Test)	-	1000	-
Cl.7.2.2(Cl.7.2.2)	-	1000	-
Cl.7.2.3(Weld ability Test)	-	1000	-
Cl.7.2.3(Weld ability Test)	-	1000	-
6.2 (iii) Rubber Rings (a) Shore hardness(Shore hardness)	-	1000	-
6.2 (iii) Rubber Rings (b) Accelerated Storage test(Accelerated Storage test)	-	1000	-
5(Dimensions of pipe (outside diameter, ovality, wall thickness))	-	1000	-
6.1(Tensile strength at Yield & Elongation at break)	-	1000	-
6.2.1(Base Density x 2)	-	1000	-
7.1.7(Melt flow rate)	-	1000	-
7.2.1(Leakage Test)	-	1000	-
7.2.2(Hydraulic Proof Test)	-	1000	-
7.2.3(Weldability Test)	-	1000	-
6.2.1(Wall thickness of male & female coupler)	-	1000	-
6.2.4(Workmanship and appearance (Visual))	-	1000	-
6.2.5(Holding attachment for coupler parts)	-	1000	-
7.3(Quick Couple Fitting)	-	1000	-
10(Marking)	-	1000	-
5.1.2(Squareness)	-	1000	-
Cl 6.3.5, Table 5 Dimension of Quick Coupled Sprinkler Saddles (Foot Batten)(Table 5 Dimension of Quick Coupled Sprinkler Saddles (Foot Batten))	-	1000	-
7.1.4(Tensile Test)	-	1000	-
7.1.5(Fusion Compatibility Test)	-	1000	-
6.2.6(Material Identification (Chemical Analysis))	-	1000	-
6.2.6(Color)	-	1000	-
6.2.6(Rubber Ring Hardness Shore – A (Before Ageing))	-	1000	-
6.2.6(Ageing Charges for rubber ring)	-	1000	-
7.1.1(Visual appearance of pipes)	-	1000	-
7.1.2(Hydraulic Characteristics)	-	1000	-
7.1.2((a) Acceptance Test (48 hrs) / 80˚ C)	-	1000	-
7.1.2((b) Type test ( 165 hrs) / 80˚ C)	-	1000	-
7.1.4(Tensile strength & elongation)	-	1000	-
7.1.5(Fusion Compatibility test)	-	1000	-
7.1.5((a) Acceptance Test (48 hrs) / 80˚ C)	-	1000	-
7.1.5((b) Type test ( 165 hrs) / 80˚ C)	-	1000	-
7.1.6(Corrected Density)	-	1000	-
7.1.6(Base Density)	-	1000	-
7.2.3((a) Acceptance Test (48 hrs) / 80˚ C)	-	1000	-
7.2.3((b) Type test ( 165 hrs) / 80˚ C)	-	1000	-
8(Supply of pipe (Visual))	-	1000	-
4.1.1 (Table-1)(Density)	-	1000	-
4.1.1 (Table-1)(Tensile strength at Yield & Elongation at break)	-	1000	-
4.1.3, Table 1,(i)(Bass density)	-	1000	-
4.1.3, Table 1,(vi)(Minimum tensile strength at yield)	-	1000	-
4.1.3, Table 1,(vii)(Minimum elongation at break)	-	1000	-
4.1.7(Rework Material)	-	1000	-
4.2(Metallic Couplers)	-	1000	-
5.1, Table 1,(i)(Plain pipes)	-	1000	-
5.1, Table 1,(ii)(90° Bends and tee)	-	1000	-
5.1, Table 1,(iii)(Base pipe )	-	1000	-
5.1, Table 1,(iv)(PCN)	-	1000	-
5.1, Table 1,(v)(Reducers, ferrule reducers)	-	1000	-
5.1, Table 1,(vi)(End caps, insert valve coupler, valve openers)	-	1000	-
5.1, Table 1,(vii)(Riser pipe and socket)	-	1000	-
7.1.1(Visual Appearance and Workmanship)	-	1000	-
7.1.2(Hydraulic Performance Characteristic)	-	1000	-
7.1.6(Corrected Density)	-	1000	-
4.3(Anti-oxidant)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Aluminium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Copper Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Magnesium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Silicon Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Iron Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Manganese Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Zinc Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Titanium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Chromium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Remarks)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Aluminium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Copper Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Magnesium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Silicon Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Iron Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Manganese Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Zinc Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Titanium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Chromium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Remarks)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Aluminium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Copper Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Magnesium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Silicon Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Iron Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Manganese Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Zinc Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Titanium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Chromium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Remarks)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Aluminium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Copper Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Magnesium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Silicon Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Iron Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Manganese Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Zinc Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Titanium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Chromium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Remarks)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Aluminium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Copper Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Magnesium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Silicon Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Iron Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Manganese Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Zinc Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Titanium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Chromium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Cr + Mn)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Aluminium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Copper Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Magnesium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Silicon Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Iron Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Manganese Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Zinc Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Titanium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Chromium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Cr + Mn)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Aluminium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Copper Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Magnesium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Silicon Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Iron Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Manganese Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Zinc Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Titanium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Chromium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Cr + Mn)	-	-	-
5(Dimensions of pipe - i) Outside diameter)	-	-	-
5(Dimensions of pipe - ii) Wall thickness minimum)	-	-	-
6(Visual Appearance)	-	-	-
7.1(Hydraulic Characteristics - Quality test)	-	-	-
7.1(Hydraulic Characteristics - Acceptance test)	-	-	-
7.2(Reversion Test)	-	-	-
7.3(Tensile Test- i) Tensile Strength)	-	-	-
7.3(Tensile Test - ii)Elongation at Break)	-	-	-
7.4(Fusion Compatibility Test- a) Quality test)	-	-	-
7.4(Fusion Compatibility Test- b) Acceptance test)	-	-	-
7.5(Density)	-	-	-
7.6(Melt Flow Rate)	-	-	-
7.6(Melt Flow Rate)	-	-	-
4.2(Carbon black- a)carbon content)	-	-	-
4.2(Carbon black- b) Dispersion of carbon black)	-	-	-
7.6(Melt now Rate (MFR))	-	-	-
7.5(Density)	-	-	-
7.4 Table-2(Fusion Compatibility Test)	-	-	-
7.3(Tensile Test)	-	-	-
7.2(Reversion Test)	-	-	-
7.1 Table -2(Hydraulic Characteristics)	-	-	-
6.1(VISUAL APPEARANCE)	-	-	-
5.1.2(Ovality)	-	-	-
5.1 table -1(DIMENSIONS OF PIPES)	-	-	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Copper Content)	-	-	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Silicon Content)	-	-	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Magnesium Content)	-	-	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Iron Content)	-	-	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Manganese Content)	-	-	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Nickel Content)	-	-	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Zinc Content)	-	-	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Lead Content)	-	-	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Tin Content)	-	-	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Titanium Content)	-	-	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Aluminium Content)	-	-	-
Cl. 4.2 , IS 2530-1963, Cl. 10(Cabon Black Content)	-	-	-
4.1.2(The MFR of the material shall be between 0.2 to 1.1 (both inclusive) when tested at 190 T at a nominal load of 50 N by the method prescribed in 7 of IS 2530. The MFR of the material shall also be within 20% of the value declared by the manufacturer.’)	-	-	-
4.1.1(density shall be between 940.4 kg/m’ and 958.4 kg/m3 (both inclusive) when determined at 27°C according to procedure prescribed in Annex A of IS 7328. The value of the density shall also not differ from the nominal value by more than 3 kg/m2 as per 5.2.1.1 of IS 7328.)	-	-	-
4.1(melt flow rating (MFR) shall not exceed 1.10 g/10 min.)	-	-	-
3(CLASSIFICATION OF PIPES)	-	-	-
4.1(Quick Coupled Male and Female Couplers)	-	-	-
4.1(Quick Coupled Male and Female Couplers)	-	-	-
4.1.3(Workmanship and appearance)	-	-	-
4.1.4(Holding attachments for coupler parts)	-	-	-
6.1.3(Weldability Test- a) Quality test)	-	-	-
6.1.3(Weldability Test- b) Acceptance test)	-	-	-
3(Quick Coupled pipes)	-	-	-
3(QUICK COUPLED PIPES)	-	-	-
4(QUICK COUPLED FITTINGS)	-	-	-
4.1 (a)(Quick Coupled Male and Female Couplers)	-	-	-
4.1 (b)(HDPE couplers —)	-	-	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Carbon Content)	-	-	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Manganese Content)	-	-	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Sulphur Content)	-	-	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Phosphorous Content)	-	-	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Al-Killed(Aluminium Content)	-	-	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Si-Killed(Silicon Content)	-	-	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Al-Si-Killed(Silicon Content)	-	-	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Al-Si-Killed(Aluminium Content)	-	-	-
Cl.4.1.3, T-1(Volatile Matter)	-	-	-
Cl.4.1.3, T-1(Volatile Matter)	-	-	-
Cl.4.1.3, T-1(Volatile Matter)	-	-	-
Cl.4.1.3, T-1(Volatile Matter)	-	-	-
Cl.4.1.3, T-1(Volatile Matter)	-	-	-
Cl.4.1.3, T-1(Volatile Matter)	-	-	-
Cl.4.1.3, T-1(Volatile Matter)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl. 4.1.1.2.1, IS 14151 (P-1)-1999, Cl. 4, IS 2530-1963, Cl. 10(Cabon Black Content)	-	-	-
Cl. 4.1.1.2.1, IS 14151 (P-1)-1999, Cl. 4, IS 2530-1963, Cl. 16(Carbon Black Dispersion)	-	-	-
4.1 .1.2.1(HDPE couplers)	-	-	-
4.1 .1.2.2(HDPE couplers)	-	-	-
4.1.4(a)(Holding Attachments for Coupler Parts)	-	-	-
4.1.4(b)(Holding Attachments for Coupler Parts)	-	-	-
4.2.1(Quick Coupled ~pe HDPE Fittings)	-	-	-
4.2.2(Quick Coupled ~pe HDPE Fittings)	-	-	-
4.2.3(Quick Coupled ~pe HDPE Fittings)	-	-	-
4.2.4(Quick Coupled ~pe HDPE Fittings)	-	-	-
4.2.5(Quick Coupled ~pe HDPE Fittings)	-	-	-
4.2.6(Quick Coupled ~pe HDPE Fittings)	-	-	-
4.2.7(Quick Coupled ~pe HDPE Fittings)	-	-	-
4.2.7(1 Dimensions of Quick Coupled Pipes and Fittings)	-	-	-
4.2.7(Reducers Table 1 and 2 of IS 8008 (Part 4))	-	-	-
4.2.7(Ferrule reducers Table 1 of IS 8008 (Part 5))	-	-	-
4.2.7(Pipe ends Table 1 of IS 8008 (Part 6))	-	-	-
4.2.7(End caps Table 1 of IS 8008 (Part 9))	-	-	-
4.2.7(Insert vatve couplers Table 1 of IS 8008 (Part 3))	-	-	-
4.2.7(Valve openers Table 1 of IS 8008 (Part 2))	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
6.1(Volatile Matter)	-	-	-
6.1(Water content)	-	-	-
6.2.1(Volatile Matter x 2)	-	-	-
6.2.1(Water content x 2)	-	-	-
4.1.1 (Table-1)(Volatile Matter)	-	-	-
4.1.1 (Table-1)(Water content)	-	-	-
4.1.3, Table 1,(iv)(Volatile matter)	-	-	-
4.1.3, Table 1,(v)(Water content)	-	-	-
5.2(Dimensions of Quick Coupled Sprinkler Saddles Table 1.)	-	-	-
6.1(Quick Coupled Pipes and Fittings)	-	-	-
6.1.1, 6.1.1.1(Leakage Test)	-	-	-
6.1.1, 6.1.1.1(Leakage Test)	-	-	-
6.1.2, 6.1.2.1(Hydraulic Proof Test)	-	-	-
6.1.2.2(Hydraulic Proof Test)	-	-	-
6.1.2.2(Hydraulic Proof Test)	-	-	-
6.1.3, 6.1.3.1(Weldability Test)	-	-	-
6.1.3.1.1(Weldability Test)	-	-	-
6.1.3.2(Quick coupled fittings)	-	-	-
6.2, 6.2.1(Quick Coupled Fittings)	-	-	-
7.2.1(Visual and Workmanship Requirement)	-	-	-
6.2 b(Material Identification - Male & Female Coupler)	-	-	-
6.3.3(Material Identification - Insert Valve Coupler)	-	-	-
6.3.3(Material Identification - Insert Valve Coupler)	-	-	-
6.3.4()	-	-	-
6.3.5(Material Identification - Saddle)	-	-	-
6.3.5(Material Identification - Pipe Ends)	-	-	-
6.3.6(Quick Coupled Pump Connectors - Visual)	-	-	-
4.2(Metallic Couplers)	-	-	-
4.2(Metallic Couplers)	-	-	-
7.2.1(Leakage Test)	-	-	-
Cl.4.1.3(Den sity Test)	-	-	-
Cl.4.1.3(MFR Test)	-	-	-
Cl.4.1.3(MFR Test)	-	-	-
Cl.4.1.3(MFR Test)	-	-	-
Cl.4.1.3(MFR Test)	-	-	-
Cl.4.1.3(Thermal Stabi lity)	-	-	-
Cl.4.1.3(Thermal Stabi lity)	-	-	-
Cl.7.1.7(MFR Test)	-	-	-
Cl.7.1.7(MFR Test)	-	-	-
Cl.7.1.7(MFR Test)	-	-	-
Cl.7.1.7(MFR Test)	-	-	-
Cl.4.1.4(Carbon Black Content)	-	-	-
Cl.4.1.4(Carbon Black Content)	-	-	-
Cl.4.1.4(Carbon Black Content)	-	-	-
Cl.4.1.4(Carbon Black Di spersion)	-	-	-
Cl.4.1.4(Carbon Black Di spersion)	-	-	-
Cl.4.1.4(Carbon Black Di spersion)	-	-	-
Cl.7.1.3(Reversion Test)	-	-	-
Cl.7.1.3(Reversion Test)	-	-	-
Cl.7.2.l(Leakage Test)	-	-	-
Cl.7.2.l(Leakage Test)	-	-	-
Cl.7.2.l(Leakage Test)	-	-	-
Cl.7.2.l(Leakage Test)	-	-	-
Cl.7.2.l(Leakage Test)	-	-	-
6.1(Thermal Stability (OIT))	-	-	-
6.1(Carbon Black Content)	-	-	-
6.1(Carbon Black Dispersion)	-	-	-
6.2.1(Melt Flow Index x 2)	-	-	-
6.2.1(Thermal Stability (OIT) x 2)	-	-	-
6.2.1(Carbon Black Content x 2)	-	-	-
6.2.1(Carbon Black Dispersion x 2)	-	-	-
7.1.3(Reversion)	-	-	-
6.2.5(Material Composition (Chemical Analysis))	-	-	-
4.2.2(Coating thickness (Hot dip Galvanized or Electroplated or Passivated or Powder Coated))	-	-	-
Cl.5(Di men sion)	-	-	-
Cl.5.1.l(Outside Diameter)	-	-	-
Cl.5.1.l(Outside Diameter)	-	-	-
Cl.6.2.L(Wall Thickness)	-	-	-
Cl.6.2.4(Workmanship and Appearance)	-	-	-
Cl.6.2.6(Rubber Ring Hardness)	-	-	-
Cl.6.2.6(Ageing Test)	-	-	-
Cl.7.1.l(Visual Anneara nce)	-	-	-
Cl.7.1.2(Hydraulic Characteristic)	-	-	-
Cl.7.1.2(Hydraulic Characteristic)	-	-	-
Cl.7.1.2(Hydraulic Characteristic)	-	-	-
Cl.7.1.2(Hydraulic Characteristic)	-	-	-
7.1.6(Carbon black Content)	-	-	-
7.1.7(Melt Flow Rate (MFR))	-	-	-
7.2.1(Leakage test 1hour / 27°C)	-	-	-
7.2.2(Hydraulic Proof test 1hour / 27°C)	-	-	-
4.1.1 (Table-1)(Melt Flow Index)	-	-	-
4.1.1 (Table-1)(Oxidation Induction Time)	-	-	-
4.1.4(Carbon Black Content)	-	-	-
4.1.4(Carbon Black Dispersion)	-	-	-
4.1.1(Polyethylene material)	-	-	-
4.1.3, Table 1,(ii)(Melt flow rate)	-	-	-
4.1.3, Table 1,(iii)(Thermal stability)	-	-	-
Cl.7.1.4(Tensile Test)	-	-	-
Cl.7.1.4(Tensile Test)	-	-	-
Cl.7.1.4(Tensile Test)	-	-	-
Cl.7.1.4(Elongation)	-	-	-
Cl.7.1.4(Elongation)	-	-	-
Cl.7.1.5(Fusion Compatibility)	-	-	-
Cl.7.1.5(Fusion Compatibility)	-	-	-
Cl.7.1.5(Fusion Compatibility)	-	-	-
Cl.7.1.5(Fusion Compatibility)	-	-	-
Cl.7.1.6(Corrected Density)	-	-	-
4.1.4(The Carbon Content and Dispersion)	-	-	-
4.1.5(Carbon Black Specification)	-	-	-
4.1.6(Antioxidant)	-	-	-
7.1.3(Reversion Test)	-	-	-
Cl.7.2.2(Cl.7.2.2)	-	-	-
Cl.7.2.3(Weld ability Test)	-	-	-
Cl.7.2.3(Weld ability Test)	-	-	-
6.2 (iii) Rubber Rings (a) Shore hardness(Shore hardness)	-	-	-
6.2 (iii) Rubber Rings (b) Accelerated Storage test(Accelerated Storage test)	-	-	-
5(Dimensions of pipe (outside diameter, ovality, wall thickness))	-	-	-
6.1(Tensile strength at Yield & Elongation at break)	-	-	-
6.2.1(Base Density x 2)	-	-	-
7.1.7(Melt flow rate)	-	-	-
7.2.1(Leakage Test)	-	-	-
7.2.2(Hydraulic Proof Test)	-	-	-
7.2.3(Weldability Test)	-	-	-
6.2.1(Wall thickness of male & female coupler)	-	-	-
6.2.4(Workmanship and appearance (Visual))	-	-	-
6.2.5(Holding attachment for coupler parts)	-	-	-
7.3(Quick Couple Fitting)	-	-	-
10(Marking)	-	-	-
5.1.2(Squareness)	-	-	-
Cl 6.3.5, Table 5 Dimension of Quick Coupled Sprinkler Saddles (Foot Batten)(Table 5 Dimension of Quick Coupled Sprinkler Saddles (Foot Batten))	-	-	-
7.1.4(Tensile Test)	-	-	-
7.1.5(Fusion Compatibility Test)	-	-	-
6.2.6(Material Identification (Chemical Analysis))	-	-	-
6.2.6(Color)	-	-	-
6.2.6(Rubber Ring Hardness Shore – A (Before Ageing))	-	-	-
6.2.6(Ageing Charges for rubber ring)	-	-	-
7.1.1(Visual appearance of pipes)	-	-	-
7.1.2(Hydraulic Characteristics)	-	-	-
7.1.2((a) Acceptance Test (48 hrs) / 80˚ C)	-	-	-
7.1.2((b) Type test ( 165 hrs) / 80˚ C)	-	-	-
7.1.4(Tensile strength & elongation)	-	-	-
7.1.5(Fusion Compatibility test)	-	-	-
7.1.5((a) Acceptance Test (48 hrs) / 80˚ C)	-	-	-
7.1.5((b) Type test ( 165 hrs) / 80˚ C)	-	-	-
7.1.6(Corrected Density)	-	-	-
7.1.6(Base Density)	-	-	-
7.2.3((a) Acceptance Test (48 hrs) / 80˚ C)	-	-	-
7.2.3((b) Type test ( 165 hrs) / 80˚ C)	-	-	-
8(Supply of pipe (Visual))	-	-	-
4.1.1 (Table-1)(Density)	-	-	-
4.1.1 (Table-1)(Tensile strength at Yield & Elongation at break)	-	-	-
4.1.3, Table 1,(i)(Bass density)	-	-	-
4.1.3, Table 1,(vi)(Minimum tensile strength at yield)	-	-	-
4.1.3, Table 1,(vii)(Minimum elongation at break)	-	-	-
4.1.7(Rework Material)	-	-	-
4.2(Metallic Couplers)	-	-	-
5.1, Table 1,(i)(Plain pipes)	-	-	-
5.1, Table 1,(ii)(90° Bends and tee)	-	-	-
5.1, Table 1,(iii)(Base pipe )	-	-	-
5.1, Table 1,(iv)(PCN)	-	-	-
5.1, Table 1,(v)(Reducers, ferrule reducers)	-	-	-
5.1, Table 1,(vi)(End caps, insert valve coupler, valve openers)	-	-	-
5.1, Table 1,(vii)(Riser pipe and socket)	-	-	-
7.1.1(Visual Appearance and Workmanship)	-	-	-
7.1.2(Hydraulic Performance Characteristic)	-	-	-
7.1.6(Corrected Density)	-	-	-

15 May, 2027

-
Included w.e.f 11.12.2025

1507

Bharat Test House Pvt Ltd 1474 Sonipat Haryana

9135626

IS/IEC 61730 : PART 1 (2023)

Photovoltaic (PV) Module Safety Qualification Part 1 Requirements for Construction (Second Revision)

Photovoltaic (PV) Module

245000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Classification, applications and intended use)	-	2500	-
6.2(Marking and documentation)	-	5000	-
6.3.2(Internal wiring)	-	100000	-
6.3.3(External wiring and cables)	-	100000	-
6.3.4(Module overcurrent protection rating)	-	100000	-
6.3.5(Connectors)	-	100000	-
6.3.6(Junction boxes)	-	100000	-
6.3.7(Frontsheets and backsheets)	-	100000	-
6.3.8(Insulation barriers)	-	100000	-
6.3.9(Electrical connections)	-	100000	-
6.3.10(Encapsulants)	-	100000	-
6.3.11(Bypass diodes)	-	100000	-
6.4(Mechanical and electromechanical connections)	-	45000	-
6.4.2(Screw connections)	-	45000	-
6.4.3(Rivets)	-	45000	-
6.4.4(Thread-cutting screws)	-	45000	-
6.4.5(Form/press/tight fit)	-	45000	-
6.4.6(Connections by adhesives)	-	45000	-
6.4.7(Other connections)	-	45000	-
6.5.2(Polymeric materials)	-	67500	-
6.5.2.3(Flammability)	-	67500	-
6.5.3.2(Current-carrying parts)	-	67500	-
6.5.4(Adhesives)	-	67500	-
6.6.2(Protection against accessibility to hazardous live parts)	-	25000	-
6.6.3(Insulation coordination)	-	25000	-
6.6.3.2.1(Pollution degree)	-	25000	-
6.6.3.3(Creepage distance)	-	25000	-
6.6.3.4(Clearance)	-	25000	-
6.6.4(Distance through functional and relied upon insulation)	-	25000	-
6.6.4.3(Cemented joints)	-	25000	-
6.6.4.4(Distance through functional insulation)	-	25000	-

19 Mar, 2026

-
Included w.e.f. 11.09.2025

1508

ALPHA TEST HOUSE PVT LTD, BAHADURGARH

8185306

IS 14887 (2014)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg food grains – Specification (first revision)

All

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2(Tapes – Width and Thickness ( IS 6192/IS 11197))	-	1000	-
3.2(Tapes – Linear Density (IS 6192/IS 11197))	-	1000	-
3.2(Tapes – Tenacity (IS 6192/IS 11197))	-	1000	-
3.2(Tapes – Elongation at point of rupture (IS 6192/IS 11197))	-	1000	-
3.2(Tapes – Heat Shrinkage (HDPE) (Cl. 3.2 and IS 6192))	-	1000	-
3.2(Tapes – Colour Fastness for pigmented tapes (IS 6192/IS 11197))	-	1000	-
3.2(Tapes – Dimensional stability (PP) (IS 11197))	-	1000	-
3.2(Unlaminated Fabric Mass )	-	1000	-
3.3.1(Bottom seam (IS 10789))	-	1000	-
4.1 and 3.4(Mass of bale (Cl. 4.1), Capacity (Cl 3.4))	-	1000	-
4.2 and Table 1 ii(Dimensions )	-	1000	-
5.2 and Table 1 iii(Ends per dm )	-	500	-
5.2 and Table 1 iv(Picks per dm )	-	500	-
4.2 and Table 1 v(Mass of sack )	-	500	-
4.2 and Table 1 vi(Average breaking strength of fabric )	-	500	-
4.2 and Table 1 vi(Breaking strength of bottom seam )	-	500	-
4.2 and Table 1 viii(Elongation at break of fabric )	-	500	-
4.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	500	-
4.2 and Table 1 x(Ash content )	-	500	-
3.2(Tapes – Width and Thickness ( IS 6192/IS 11197))	-	0	-
3.2(Tapes – Linear Density (IS 6192/IS 11197))	-	0	-
3.2(Tapes – Tenacity (IS 6192/IS 11197))	-	0	-
3.2(Tapes – Elongation at point of rupture (IS 6192/IS 11197))	-	0	-
3.2(Tapes – Heat Shrinkage (HDPE) (Cl. 3.2 and IS 6192))	-	0	-
3.2(Tapes – Colour Fastness for pigmented tapes (IS 6192/IS 11197))	-	0	-
3.2(Tapes – Dimensional stability (PP) (IS 11197))	-	0	-
3.2(Unlaminated Fabric Mass )	-	0	-
3.3.1(Bottom seam (IS 10789))	-	0	-
4.1 and 3.4(Mass of bale (Cl. 4.1), Capacity (Cl 3.4))	-	0	-
4.2 and Table 1 ii(Dimensions )	-	0	-
5.2 and Table 1 iii(Ends per dm )	-	0	-
5.2 and Table 1 iv(Picks per dm )	-	1500	-
4.2 and Table 1 v(Mass of sack )	-	0	-
4.2 and Table 1 vi(Average breaking strength of fabric )	-	0	-
4.2 and Table 1 vi(Breaking strength of bottom seam )	-	0	-
4.2 and Table 1 viii(Elongation at break of fabric )	-	0	-
4.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	0	-
4.2 and Table 1 x(Ash content )	-	0	-
3.1(Material Identification)	-	0	-
3.1(Overall Migration)	-	0	-
3.2(Density)	-	0	-
3.2(MFI)	-	0	-
Cl 3.2 (Mesh size)(Mesh size)	-	0	-
Cl 3.2 (Weight in g/m2) (Amendment 3)(Weight in g/m2)	-	0	-
3.3.2(Mouth)	-	0	-
3.2(Tapes – Width and Thickness ( IS 6192/IS 11197))	-	0	-
3.2(Tapes – Linear Density (IS 6192/IS 11197))	-	0	-
3.2(Tapes – Tenacity (IS 6192/IS 11197))	-	0	-
3.2(Tapes – Elongation at point of rupture (IS 6192/IS 11197))	-	0	-
3.2(Tapes – Heat Shrinkage (HDPE) (Cl. 3.2 and IS 6192))	-	0	-
3.2(Tapes – Colour Fastness for pigmented tapes (IS 6192/IS 11197))	-	0	-
3.2(Tapes – Dimensional stability (PP) (IS 11197))	-	0	-
3.2(Unlaminated Fabric Mass )	-	0	-
3.3.1(Bottom seam (IS 10789))	-	0	-
4.1 and 3.4(Mass of bale (Cl. 4.1), Capacity (Cl 3.4))	-	0	-
4.2 and Table 1 ii(Dimensions )	-	0	-
5.2 and Table 1 iii(Ends per dm )	-	0	-
5.2 and Table 1 iv(Picks per dm )	-	0	-
4.2 and Table 1 v(Mass of sack )	-	0	-
4.2 and Table 1 vi(Average breaking strength of fabric )	-	0	-
4.2 and Table 1 vi(Breaking strength of bottom seam )	-	0	-
4.2 and Table 1 viii(Elongation at break of fabric )	-	0	-
4.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	0	-
4.2 and Table 1 x(Ash content )	-	0	-
3.2(Tapes – Width and Thickness ( IS 6192/IS 11197))	-	0	-
3.2(Tapes – Linear Density (IS 6192/IS 11197))	-	0	-
3.2(Tapes – Tenacity (IS 6192/IS 11197))	-	0	-
3.2(Tapes – Elongation at point of rupture (IS 6192/IS 11197))	-	0	-
3.2(Tapes – Heat Shrinkage (HDPE) (Cl. 3.2 and IS 6192))	-	0	-
3.2(Tapes – Colour Fastness for pigmented tapes (IS 6192/IS 11197))	-	0	-
3.2(Tapes – Dimensional stability (PP) (IS 11197))	-	0	-
3.2(Unlaminated Fabric Mass )	-	0	-
3.3.1(Bottom seam (IS 10789))	-	0	-
4.1 and 3.4(Mass of bale (Cl. 4.1), Capacity (Cl 3.4))	-	0	-
4.2 and Table 1 ii(Dimensions )	-	0	-
5.2 and Table 1 iii(Ends per dm )	-	0	-
5.2 and Table 1 iv(Picks per dm )	-	0	-
4.2 and Table 1 v(Mass of sack )	-	0	-
4.2 and Table 1 vi(Average breaking strength of fabric )	-	0	-
4.2 and Table 1 vi(Breaking strength of bottom seam )	-	0	-
4.2 and Table 1 viii(Elongation at break of fabric )	-	0	-
4.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	0	-
4.2 and Table 1 x(Ash content )	-	0	-
3.1(Material Identification)	-	0	-
3.1(Overall Migration)	-	0	-
3.2(Density)	-	0	-
3.2(MFI)	-	0	-
Cl 3.2 (Mesh size)(Mesh size)	-	0	-
Cl 3.2 (Weight in g/m2) (Amendment 3)(Weight in g/m2)	-	0	-
3.3.2(Mouth)	-	0	-

08 May, 2028

-
Included w.e.f.29.09.2025

1509

International Testing Centre, MSME Technology Development Centre, Meerut

8177804

IS 3976 (2018)

Safety Rubber Canvas Boots for Miners Ã¢â‚¬ Specification ( Sixth Revision )

46500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.5.2.5 Compact Sole Heel Cl.5.2.5.1 IS 3400 (Part 2)(requirements prescribed in col 3 of Table 2 when tested as per corresponding test methods prescribed in col 4 of Table 2. i)i) Hardness (IRHD)	-	500	-
Cl.6.3 Tear Strength of Compact Outsole( When outsoles are tested in accordance to 8.2 of IS 15298 (Part 1), the tear strength shall be not less than 8 kN/m for material having density higher than 0.9/cm³ and when density of material is less than or equal to 0.9 g/cm³, tear strength shall not be less than 5 kN/m.)	-	500	-
Cl.5.2.3 Coated Binding Material IS 1954( Coated binding materials shall conform to the requirements given in col 3 of Table 1 when tested according to the methods prescribed in col 4 of Table 1. i)Width in mm, )	-	500	-
Cl.5.2.1.4 ( Type 2 footwear, the composite upper material shall comply with requirements of water coefficient as prescribed in 5.4.6 of IS 15298 (Part 2).)	-	500	-
Cl.5.13 Energy Absorption Test(When footwear is tested in accordance with the method prescribed in 5.14 of IS 15298 (Part 1), the energy absorption of the seat region shall not be less than 20 J.)	-	500	-
Cl.5.2.3 Coated Binding Material Annex C(ii) Breaking load in N, Min (50 cm grip length test specimen) )	-	500	-
Cl.5.2.1.4 ( Type 2 footwear, the composite upper material shall comply with requirements of water vapour permeability as prescribed in 5.4.6 of IS 15298 (Part 2).)	-	500	-
CL.5.2.10 Counter Stiffener( A counter stiffener, made out of textile reinforced withpolymer/rubber including (thermoplastic) having thickness not less than 1.5 mm is to be stitched at inside of upper so as to fortify the back of the footwear at joints of quarter.)	-	500	-
Cl.5.1.1 Fittings(Fittings of the footwear shall be in conformity to Table 9 of IS 1638 (measurement of men’s lasts) and Table 8 of IS 1638 (measurement of women’s lasts).)	-	300	-
Cl.5.2.1 Upper Cl.5.2.1.1 IS 3400(Part 5)( Composite upper material shall comply with consolidation test as per 5.10.(IS 3400 (Part 5). There shall be no separation at a load of 1.5 kg.))	-	500	-
Cl.5.2.1.2( Composite upper material shall comply with tear strength as per 5.4.3 of IS 15298 (Part 2).)	-	500	-
Cl.5.2.1.3 , Cl.6.5 of IS 15298 (Part 1).( Composite upper material shall develop no cracks before 150 000 cycles when tested in accordance with 6.5 of IS 15298 (Part 1).)	-	500	-
Cl.5.2.1.5( Inner layer of upper shall meet requirement of abrasion resistance as prescribed in 5.5.2 of IS 15298 (Part 2).)	-	500	-
Cl.5.2.2 Compact Insole/Compact Insocks/Counter Stiffener Lining(Textile material shall be used as lining material for compact insole/compact insocks / counter stiffener. It shall meet the requirement of tear strength as prescribed in 5.6.1 of IS 15298 (Part 2).)	-	500	-
Cl.5.2.2.1 Abrasion resistance of compact insole/insocks/ counter stiffener( When textiles used as lining for all the above are tested in accordance with 6.12 of IS 15298 (Part 1), the lining shall not develop any holes before the following number of cycles has been performed:)	-	800	-
Cl.5.2.3.1 In case of cotton black binding materia( the same shall be free from sulphur dyes when tested in accordance with Annex B.)	-	500	-
Cl.5.2.5 Compact Sole Heel Cl. 5.2.5.1 (The compact sole heel shall be made out of polymeric/rubber components and the typical design recommendation (not mandatory) of compact sole heel is as shown in Fig. 3. Sectional view of Type 1/Type 2 ) toe position is given in Fig. 4.)	-	500	-
Cl.5.2.5 Compact Sole Heel 5.2.5.1 IS 3400 (Part 4)(ii)*Change in hardness after accelerated ageing at 100 ± 2 °C for 24 h )	-	500	-
Cl.5.2.5.3 Ageing for whole footwear(When rubber is used for manufacturing boots or when the outer sole heel is made of bi-polymer, the finished boots shall be aged at 100 ± 2°C for 24 h. On completion of test, all rubber components shall not develop any sign of tackiness or brittleness.)	-	1000	-
Cl.5.2.5.4 Thickness of compact sole hee(Thickness of compact sole heel of the boots shall comply with the thickness and material requirements prescribed in Table 3.)	-	500	-
Cl.5.2.5.4 Thickness of compact sole hee(of black cotton thread, the same shall be free from sulphur dyes when tested in accordance with Annex B.)	-	500	-
Cl.5.2.6 Thread for Upper Closing( The length (m/kg) and construction of sewing thread shall conform to requirements as prescribed in Table 4.)	-	300	-
Cl.5.2.7 Safety Toe Cap(Safety toe cap as per 3.6 shall be fitted into the footwear and must not come out while in use.)	-	500	-
Cl.5.2.8.1( The boots shall be provided with laces having minimum length of 115 cm for Type 1 and minimum 100 cm for Type 2.)	-	300	-
Cl.5.2.8.2 (Minimum breaking load of 60 kg is to be achieved when tested between 18 cm grip length in accordance with Annex C.)	-	500	-
Cl.5.2.8.3( In case of cotton lace of black colour, the same shall be free from sulphur dyes when tested in accordance with Annex B. Two ends of the laces shall be provided with plastic tips.)	-	500	-
Cl.5.2.9 Eyelets( Aluminum eyelets of external collar diameter not less than 10 mm and wall thickness of 0.30 to 0.35 mm shall be used.)	-	500	-
Cl.5.3.2 (The tongue shall be made out of composite upper material and shall be half bellow type for Type 2 and full bellow type for Type 1.)	-	300	-
Cl.5.3.5 Outer toe cap( shall be provided which is made of polymer/rubber and it shall be strongly adhered such that it shall not open up or come out while in use. Toe of the boot shall be reinforced with safety toe cap)	-	500	-
Cl.5.3.6( A designed foxing of width of minimum 25 mm and of thickness of minimum 2 mm is to be provided. The foxing shall not extend the edges of the outer sole.)	-	300	-
Cl.5.3.7( Two pairs of detachable insocks are to be provided. The insocks shall be compact in nature having thickness not less than 2 mm.)	-	300	-
Cl.5.4 Finish( In appearance, general workmanship and in all other respects with regard to finish and get up of the footwear, the footwear shall be matching to the approved sample of the purchaser.)	-	300	-
Cl.5.5 Mass(The mass of one pair of finished footwear of size 8 shall not exceed 1 500 g for Type 1 and 1 400 g for Type 2 with an increase or decrease of 100 g for each bigger or smaller size, respectively.)	-	300	-
Cl.5.6( Height of Upper Height of upper of the boots shall conform to column 5 (Design C) and column 4 (Design B) of 5.2.2, Table 4 of IS 15298 (Part 2) for Type 1 and Type 2, respectively when measured as per 6.2 of IS 15298 (Part 1) on the inside of the back of the footwear and from seat of the insole to top edge of the upper.)	-	300	-
Cl.5.7 Performance Test(When safety footwear is tested in accordance with the method described in 5.4 of IS 15298 (Part 1), at an impact energy of (200 ± 4) J, the clearance under the toecap at the moment of impact shall be in accordance with Table 5. In addition, the toecap shall not develop any cracks which go through the material, that is, through which light can be seen.)	-	500	-
Cl.5.8 Upper/Outsole Bond Strength(When the footwear is tested in accordance with the method prescribed in 5.2 of IS 15298 (Part 1), the bond strength shall not be less than 4.0 N/mm, unless there is tearing of the sole in which case the bond strength shall not be less than 3.0 N/mm.)	-	500	-
Cl.5.9 Sole Interlayer Bond Strength for Bi-polymer( and Bi-density Sole When tested in accordance with 5.2 of IS 15298 (Part 1), the bond strength between the outer or cleated layer and the adjacent layer shall not be less than 4.0 N/mm unless there is tearing of any part of the sole, in which case the bond strength shall not be less than 3.0 N/mm.)	-	500	-
Cl.5.10 Consolidation Test( Representative sample of width 25 ± 0.5 mm are cut out from the quarter of the upper along the length of boot. The plies are separated by breaking the bond. Carry out the test on two specimens in accordance with IS 3400 (Part 5). Th)	-	500	-
Cl.5.11 Compression Resistance( 5.11.1 When safety boots are tested in accordance with 5.5 of IS 15298 (Part 1), the clearance under the toe cap at a compression load of 15 kN ± 0.1 kN shall be in accordance with Table 5.)	-	800	-
Cl.5.12 Internal Length of Toe Cap( For safety boots, internal length of the toe cap shall meet the specification given in Table 5 of IS 15298 (Part 2) when tested as per 5.3 of IS 15298 (Part 1).)	-	300	-
Cl.6.1 Abrasion Resistance of Compact Outsole( When outsole is tested in accordance with 8.3 of IS 15298 (Part 1), the relative volume loss shall not be greater than 250 mm³ for materials having density 0.9 g/cm³ or less, and not greater than 150 mm³ for materials with density greater than 0.9 g/cm³.)	-	800	-
Cl.6.2 Flexing Resistance of Compact Outsole( When outsole is tested in accordance with 8.4 of IS 15298 (Part 1), the cut growth shall not be greater than 4 mm before 30 000 cycles.)	-	1000	-
Cl.6.4 Resistance to Hot Contact( — Sole Heel When sole heel is tested in accordance with 8.7 of IS 15298 (Part 1), the material shall not melt/deform and shall not develop any cracks when bent around the mandrel.)	-	1000	-
Cl.6.5 Hydrolysis( When bottom sole or other components are made out of polyurethane, the same shall be tested in accordance with 8.5 of IS 15298 (Part 1) and the same shall comply with 5.8.5 of IS 15298 (Part 2).)	-	3000	-
Cl.5.2.5 Compact Sole Heel Cl.5.2.5.1 IS 3400 (Part 2)(requirements prescribed in col 3 of Table 2 when tested as per corresponding test methods prescribed in col 4 of Table 2. i)i) Hardness (IRHD)	-	500	-
Cl.6.3 Tear Strength of Compact Outsole( When outsoles are tested in accordance to 8.2 of IS 15298 (Part 1), the tear strength shall be not less than 8 kN/m for material having density higher than 0.9/cm³ and when density of material is less than or equal to 0.9 g/cm³, tear strength shall not be less than 5 kN/m.)	-	500	-
Cl.5.2.3 Coated Binding Material IS 1954( Coated binding materials shall conform to the requirements given in col 3 of Table 1 when tested according to the methods prescribed in col 4 of Table 1. i)Width in mm, )	-	500	-
Cl.5.2.1.4 ( Type 2 footwear, the composite upper material shall comply with requirements of water coefficient as prescribed in 5.4.6 of IS 15298 (Part 2).)	-	500	-
Cl.5.13 Energy Absorption Test(When footwear is tested in accordance with the method prescribed in 5.14 of IS 15298 (Part 1), the energy absorption of the seat region shall not be less than 20 J.)	-	500	-
Cl.5.2.3 Coated Binding Material Annex C(ii) Breaking load in N, Min (50 cm grip length test specimen) )	-	500	-
Cl.5.2.1.4 ( Type 2 footwear, the composite upper material shall comply with requirements of water vapour permeability as prescribed in 5.4.6 of IS 15298 (Part 2).)	-	500	-
CL.5.2.10 Counter Stiffener( A counter stiffener, made out of textile reinforced withpolymer/rubber including (thermoplastic) having thickness not less than 1.5 mm is to be stitched at inside of upper so as to fortify the back of the footwear at joints of quarter.)	-	500	-
Cl.5.1.1 Fittings(Fittings of the footwear shall be in conformity to Table 9 of IS 1638 (measurement of men’s lasts) and Table 8 of IS 1638 (measurement of women’s lasts).)	-	300	-
Cl.5.2.1 Upper Cl.5.2.1.1 IS 3400(Part 5)( Composite upper material shall comply with consolidation test as per 5.10.(IS 3400 (Part 5). There shall be no separation at a load of 1.5 kg.))	-	500	-
Cl.5.2.1.2( Composite upper material shall comply with tear strength as per 5.4.3 of IS 15298 (Part 2).)	-	500	-
Cl.5.2.1.3 , Cl.6.5 of IS 15298 (Part 1).( Composite upper material shall develop no cracks before 150 000 cycles when tested in accordance with 6.5 of IS 15298 (Part 1).)	-	500	-
Cl.5.2.1.5( Inner layer of upper shall meet requirement of abrasion resistance as prescribed in 5.5.2 of IS 15298 (Part 2).)	-	500	-
Cl.5.2.2 Compact Insole/Compact Insocks/Counter Stiffener Lining(Textile material shall be used as lining material for compact insole/compact insocks / counter stiffener. It shall meet the requirement of tear strength as prescribed in 5.6.1 of IS 15298 (Part 2).)	-	500	-
Cl.5.2.2.1 Abrasion resistance of compact insole/insocks/ counter stiffener( When textiles used as lining for all the above are tested in accordance with 6.12 of IS 15298 (Part 1), the lining shall not develop any holes before the following number of cycles has been performed:)	-	800	-
Cl.5.2.3.1 In case of cotton black binding materia( the same shall be free from sulphur dyes when tested in accordance with Annex B.)	-	500	-
Cl.5.2.5 Compact Sole Heel Cl. 5.2.5.1 (The compact sole heel shall be made out of polymeric/rubber components and the typical design recommendation (not mandatory) of compact sole heel is as shown in Fig. 3. Sectional view of Type 1/Type 2 ) toe position is given in Fig. 4.)	-	500	-
Cl.5.2.5 Compact Sole Heel 5.2.5.1 IS 3400 (Part 4)(ii)*Change in hardness after accelerated ageing at 100 ± 2 °C for 24 h )	-	500	-
Cl.5.2.5.3 Ageing for whole footwear(When rubber is used for manufacturing boots or when the outer sole heel is made of bi-polymer, the finished boots shall be aged at 100 ± 2°C for 24 h. On completion of test, all rubber components shall not develop any sign of tackiness or brittleness.)	-	1000	-
Cl.5.2.5.4 Thickness of compact sole hee(Thickness of compact sole heel of the boots shall comply with the thickness and material requirements prescribed in Table 3.)	-	500	-
Cl.5.2.5.4 Thickness of compact sole hee(of black cotton thread, the same shall be free from sulphur dyes when tested in accordance with Annex B.)	-	500	-
Cl.5.2.6 Thread for Upper Closing( The length (m/kg) and construction of sewing thread shall conform to requirements as prescribed in Table 4.)	-	500	-
Cl.5.2.7 Safety Toe Cap(Safety toe cap as per 3.6 shall be fitted into the footwear and must not come out while in use.)	-	500	-
Cl.5.2.8.1( The boots shall be provided with laces having minimum length of 115 cm for Type 1 and minimum 100 cm for Type 2.)	-	500	-
Cl.5.2.8.2 (Minimum breaking load of 60 kg is to be achieved when tested between 18 cm grip length in accordance with Annex C.)	-	500	-
Cl.5.2.8.3( In case of cotton lace of black colour, the same shall be free from sulphur dyes when tested in accordance with Annex B. Two ends of the laces shall be provided with plastic tips.)	-	500	-
Cl.5.2.9 Eyelets( Aluminum eyelets of external collar diameter not less than 10 mm and wall thickness of 0.30 to 0.35 mm shall be used.)	-	500	-
Cl.5.3.2 (The tongue shall be made out of composite upper material and shall be half bellow type for Type 2 and full bellow type for Type 1.)	-	500	-
Cl.5.3.5 Outer toe cap( shall be provided which is made of polymer/rubber and it shall be strongly adhered such that it shall not open up or come out while in use. Toe of the boot shall be reinforced with safety toe cap)	-	500	-
Cl.5.3.6( A designed foxing of width of minimum 25 mm and of thickness of minimum 2 mm is to be provided. The foxing shall not extend the edges of the outer sole.)	-	500	-
Cl.5.3.7( Two pairs of detachable insocks are to be provided. The insocks shall be compact in nature having thickness not less than 2 mm.)	-	500	-
Cl.5.4 Finish( In appearance, general workmanship and in all other respects with regard to finish and get up of the footwear, the footwear shall be matching to the approved sample of the purchaser.)	-	500	-
Cl.5.5 Mass(The mass of one pair of finished footwear of size 8 shall not exceed 1 500 g for Type 1 and 1 400 g for Type 2 with an increase or decrease of 100 g for each bigger or smaller size, respectively.)	-	300	-
Cl.5.6( Height of Upper Height of upper of the boots shall conform to column 5 (Design C) and column 4 (Design B) of 5.2.2, Table 4 of IS 15298 (Part 2) for Type 1 and Type 2, respectively when measured as per 6.2 of IS 15298 (Part 1) on the inside of the back of the footwear and from seat of the insole to top edge of the upper.)	-	500	-
Cl.5.7 Performance Test(When safety footwear is tested in accordance with the method described in 5.4 of IS 15298 (Part 1), at an impact energy of (200 ± 4) J, the clearance under the toecap at the moment of impact shall be in accordance with Table 5. In addition, the toecap shall not develop any cracks which go through the material, that is, through which light can be seen.)	-	500	-
Cl.5.8 Upper/Outsole Bond Strength(When the footwear is tested in accordance with the method prescribed in 5.2 of IS 15298 (Part 1), the bond strength shall not be less than 4.0 N/mm, unless there is tearing of the sole in which case the bond strength shall not be less than 3.0 N/mm.)	-	500	-
Cl.5.9 Sole Interlayer Bond Strength for Bi-polymer( and Bi-density Sole When tested in accordance with 5.2 of IS 15298 (Part 1), the bond strength between the outer or cleated layer and the adjacent layer shall not be less than 4.0 N/mm unless there is tearing of any part of the sole, in which case the bond strength shall not be less than 3.0 N/mm.)	-	500	-
Cl.5.10 Consolidation Test( Representative sample of width 25 ± 0.5 mm are cut out from the quarter of the upper along the length of boot. The plies are separated by breaking the bond. Carry out the test on two specimens in accordance with IS 3400 (Part 5). Th)	-	500	-
Cl.5.11 Compression Resistance( 5.11.1 When safety boots are tested in accordance with 5.5 of IS 15298 (Part 1), the clearance under the toe cap at a compression load of 15 kN ± 0.1 kN shall be in accordance with Table 5.)	-	500	-
Cl.5.12 Internal Length of Toe Cap( For safety boots, internal length of the toe cap shall meet the specification given in Table 5 of IS 15298 (Part 2) when tested as per 5.3 of IS 15298 (Part 1).)	-	500	-
Cl.6.1 Abrasion Resistance of Compact Outsole( When outsole is tested in accordance with 8.3 of IS 15298 (Part 1), the relative volume loss shall not be greater than 250 mm³ for materials having density 0.9 g/cm³ or less, and not greater than 150 mm³ for materials with density greater than 0.9 g/cm³.)	-	500	-
Cl.6.2 Flexing Resistance of Compact Outsole( When outsole is tested in accordance with 8.4 of IS 15298 (Part 1), the cut growth shall not be greater than 4 mm before 30 000 cycles.)	-	1500	-
Cl.6.4 Resistance to Hot Contact( — Sole Heel When sole heel is tested in accordance with 8.7 of IS 15298 (Part 1), the material shall not melt/deform and shall not develop any cracks when bent around the mandrel.)	-	1000	-
Cl.6.5 Hydrolysis( When bottom sole or other components are made out of polyurethane, the same shall be tested in accordance with 8.5 of IS 15298 (Part 1) and the same shall comply with 5.8.5 of IS 15298 (Part 2).)	-	3000	-
Cl.5.2.5 Compact Sole Heel Cl.5.2.5.1 IS 3400 (Part 2)(requirements prescribed in col 3 of Table 2 when tested as per corresponding test methods prescribed in col 4 of Table 2. i)i) Hardness (IRHD)	-	500	-
Cl.6.3 Tear Strength of Compact Outsole( When outsoles are tested in accordance to 8.2 of IS 15298 (Part 1), the tear strength shall be not less than 8 kN/m for material having density higher than 0.9/cm³ and when density of material is less than or equal to 0.9 g/cm³, tear strength shall not be less than 5 kN/m.)	-	500	-
Cl.5.2.3 Coated Binding Material IS 1954( Coated binding materials shall conform to the requirements given in col 3 of Table 1 when tested according to the methods prescribed in col 4 of Table 1. i)Width in mm, )	-	500	-
Cl.5.2.1.4 ( Type 2 footwear, the composite upper material shall comply with requirements of water coefficient as prescribed in 5.4.6 of IS 15298 (Part 2).)	-	500	-
Cl.5.13 Energy Absorption Test(When footwear is tested in accordance with the method prescribed in 5.14 of IS 15298 (Part 1), the energy absorption of the seat region shall not be less than 20 J.)	-	500	-
Cl.5.2.3 Coated Binding Material Annex C(ii) Breaking load in N, Min (50 cm grip length test specimen) )	-	500	-
Cl.5.2.1.4 ( Type 2 footwear, the composite upper material shall comply with requirements of water vapour permeability as prescribed in 5.4.6 of IS 15298 (Part 2).)	-	500	-
CL.5.2.10 Counter Stiffener( A counter stiffener, made out of textile reinforced withpolymer/rubber including (thermoplastic) having thickness not less than 1.5 mm is to be stitched at inside of upper so as to fortify the back of the footwear at joints of quarter.)	-	500	-
Cl.5.1.1 Fittings(Fittings of the footwear shall be in conformity to Table 9 of IS 1638 (measurement of men’s lasts) and Table 8 of IS 1638 (measurement of women’s lasts).)	-	300	-
Cl.5.2.1 Upper Cl.5.2.1.1 IS 3400(Part 5)( Composite upper material shall comply with consolidation test as per 5.10.(IS 3400 (Part 5). There shall be no separation at a load of 1.5 kg.))	-	500	-
Cl.5.2.1.2( Composite upper material shall comply with tear strength as per 5.4.3 of IS 15298 (Part 2).)	-	500	-
Cl.5.2.1.3 , Cl.6.5 of IS 15298 (Part 1).( Composite upper material shall develop no cracks before 150 000 cycles when tested in accordance with 6.5 of IS 15298 (Part 1).)	-	500	-
Cl.5.2.1.5( Inner layer of upper shall meet requirement of abrasion resistance as prescribed in 5.5.2 of IS 15298 (Part 2).)	-	500	-
Cl.5.2.2 Compact Insole/Compact Insocks/Counter Stiffener Lining(Textile material shall be used as lining material for compact insole/compact insocks / counter stiffener. It shall meet the requirement of tear strength as prescribed in 5.6.1 of IS 15298 (Part 2).)	-	500	-
Cl.5.2.2.1 Abrasion resistance of compact insole/insocks/ counter stiffener( When textiles used as lining for all the above are tested in accordance with 6.12 of IS 15298 (Part 1), the lining shall not develop any holes before the following number of cycles has been performed:)	-	800	-
Cl.5.2.3.1 In case of cotton black binding materia( the same shall be free from sulphur dyes when tested in accordance with Annex B.)	-	500	-
Cl.5.2.5 Compact Sole Heel Cl. 5.2.5.1 (The compact sole heel shall be made out of polymeric/rubber components and the typical design recommendation (not mandatory) of compact sole heel is as shown in Fig. 3. Sectional view of Type 1/Type 2 ) toe position is given in Fig. 4.)	-	500	-
Cl.5.2.5 Compact Sole Heel 5.2.5.1 IS 3400 (Part 4)(ii)*Change in hardness after accelerated ageing at 100 ± 2 °C for 24 h )	-	500	-
Cl.5.2.5.3 Ageing for whole footwear(When rubber is used for manufacturing boots or when the outer sole heel is made of bi-polymer, the finished boots shall be aged at 100 ± 2°C for 24 h. On completion of test, all rubber components shall not develop any sign of tackiness or brittleness.)	-	1500	-
Cl.5.2.5.4 Thickness of compact sole hee(Thickness of compact sole heel of the boots shall comply with the thickness and material requirements prescribed in Table 3.)	-	500	-
Cl.5.2.5.4 Thickness of compact sole hee(of black cotton thread, the same shall be free from sulphur dyes when tested in accordance with Annex B.)	-	500	-
Cl.5.2.6 Thread for Upper Closing( The length (m/kg) and construction of sewing thread shall conform to requirements as prescribed in Table 4.)	-	500	-
Cl.5.2.7 Safety Toe Cap(Safety toe cap as per 3.6 shall be fitted into the footwear and must not come out while in use.)	-	500	-
Cl.5.2.8.1( The boots shall be provided with laces having minimum length of 115 cm for Type 1 and minimum 100 cm for Type 2.)	-	500	-
Cl.5.2.8.2 (Minimum breaking load of 60 kg is to be achieved when tested between 18 cm grip length in accordance with Annex C.)	-	500	-
Cl.5.2.8.3( In case of cotton lace of black colour, the same shall be free from sulphur dyes when tested in accordance with Annex B. Two ends of the laces shall be provided with plastic tips.)	-	500	-
Cl.5.2.9 Eyelets( Aluminum eyelets of external collar diameter not less than 10 mm and wall thickness of 0.30 to 0.35 mm shall be used.)	-	500	-
Cl.5.3.2 (The tongue shall be made out of composite upper material and shall be half bellow type for Type 2 and full bellow type for Type 1.)	-	500	-
Cl.5.3.5 Outer toe cap( shall be provided which is made of polymer/rubber and it shall be strongly adhered such that it shall not open up or come out while in use. Toe of the boot shall be reinforced with safety toe cap)	-	500	-
Cl.5.3.6( A designed foxing of width of minimum 25 mm and of thickness of minimum 2 mm is to be provided. The foxing shall not extend the edges of the outer sole.)	-	500	-
Cl.5.3.7( Two pairs of detachable insocks are to be provided. The insocks shall be compact in nature having thickness not less than 2 mm.)	-	300	-
Cl.5.4 Finish( In appearance, general workmanship and in all other respects with regard to finish and get up of the footwear, the footwear shall be matching to the approved sample of the purchaser.)	-	300	-
Cl.5.5 Mass(The mass of one pair of finished footwear of size 8 shall not exceed 1 500 g for Type 1 and 1 400 g for Type 2 with an increase or decrease of 100 g for each bigger or smaller size, respectively.)	-	300	-
Cl.5.6( Height of Upper Height of upper of the boots shall conform to column 5 (Design C) and column 4 (Design B) of 5.2.2, Table 4 of IS 15298 (Part 2) for Type 1 and Type 2, respectively when measured as per 6.2 of IS 15298 (Part 1) on the inside of the back of the footwear and from seat of the insole to top edge of the upper.)	-	300	-
Cl.5.7 Performance Test(When safety footwear is tested in accordance with the method described in 5.4 of IS 15298 (Part 1), at an impact energy of (200 ± 4) J, the clearance under the toecap at the moment of impact shall be in accordance with Table 5. In addition, the toecap shall not develop any cracks which go through the material, that is, through which light can be seen.)	-	500	-
Cl.5.8 Upper/Outsole Bond Strength(When the footwear is tested in accordance with the method prescribed in 5.2 of IS 15298 (Part 1), the bond strength shall not be less than 4.0 N/mm, unless there is tearing of the sole in which case the bond strength shall not be less than 3.0 N/mm.)	-	500	-
Cl.5.9 Sole Interlayer Bond Strength for Bi-polymer( and Bi-density Sole When tested in accordance with 5.2 of IS 15298 (Part 1), the bond strength between the outer or cleated layer and the adjacent layer shall not be less than 4.0 N/mm unless there is tearing of any part of the sole, in which case the bond strength shall not be less than 3.0 N/mm.)	-	500	-
Cl.5.10 Consolidation Test( Representative sample of width 25 ± 0.5 mm are cut out from the quarter of the upper along the length of boot. The plies are separated by breaking the bond. Carry out the test on two specimens in accordance with IS 3400 (Part 5). Th)	-	500	-
Cl.5.11 Compression Resistance( 5.11.1 When safety boots are tested in accordance with 5.5 of IS 15298 (Part 1), the clearance under the toe cap at a compression load of 15 kN ± 0.1 kN shall be in accordance with Table 5.)	-	500	-
Cl.5.12 Internal Length of Toe Cap( For safety boots, internal length of the toe cap shall meet the specification given in Table 5 of IS 15298 (Part 2) when tested as per 5.3 of IS 15298 (Part 1).)	-	500	-
Cl.6.1 Abrasion Resistance of Compact Outsole( When outsole is tested in accordance with 8.3 of IS 15298 (Part 1), the relative volume loss shall not be greater than 250 mm³ for materials having density 0.9 g/cm³ or less, and not greater than 150 mm³ for materials with density greater than 0.9 g/cm³.)	-	800	-
Cl.6.2 Flexing Resistance of Compact Outsole( When outsole is tested in accordance with 8.4 of IS 15298 (Part 1), the cut growth shall not be greater than 4 mm before 30 000 cycles.)	-	1500	-
Cl.6.4 Resistance to Hot Contact( — Sole Heel When sole heel is tested in accordance with 8.7 of IS 15298 (Part 1), the material shall not melt/deform and shall not develop any cracks when bent around the mandrel.)	-	1000	-
Cl.6.5 Hydrolysis( When bottom sole or other components are made out of polyurethane, the same shall be tested in accordance with 8.5 of IS 15298 (Part 1) and the same shall comply with 5.8.5 of IS 15298 (Part 2).)	-	3000	-
4(Types)	-	500	-
5(Requirements)	-	500	-
5.1(Design)	-	500	-
5.10(consolidation test IS 3400 (Part 5))	-	500	-
5.2.4(Reinforcing Material)	-	500	-
5.2.8.4(Colour of the lace)	-	300	-
5.3, 5.3.1,5.3.3,5.3.4(Construction)	-	500	-
5.10(Consolidation Test IS 3400 (Part 5) : 1986)	-	500	-
8(CHEMICAL REQUIREMENTS)	-	30000	-
9, 9.1(BIS CERTIFICATION MARKING)	-	0	-
10(Marking)	-	300	-
11(Packing)	-	300	-
Cl. 5.2.4(Reinforcing Material)	-	500	-
Cl. 5.2.8.4(Colour of the lace)	-	300	-
11(PACKING)	-	300	-
Cl. 5.3(Construction 5.3.1,5.3.3,5.3.4)	-	500	-
10(Marking)	-	300	-
7.1(Resistance to fuel)	-	1000	-
7.2(Resistance to electricity)	-	1000	-
9, 9.1(BIS CERTIFICATION MARKING)	-	0	-
Cl. 8 (IS 17011, Table-1 (i))(Allergenic and carcinogenic disperse dyes)	-	2000	-
Cl-8 (IS 17011, Table-1 (ii)(Aromatic amines released from Azo dyes (each individual amine))	-	2000	-
Cl-8 (IS 17011, Table-1 (iii)(Aromatic amines released from Azo dyes (each individual amine))	-	2000	-
Cl-8(IS 17011, Table-1 (iv)(Chromium (VI))	-	2000	-
Cl-8 (IS 17011, Table-1 (v)(Dimethyl fumarate (DMFU))	-	2000	-
Cl-8 (IS 17011, Table-1 (vi)(Formaldehyde (free or released by partial hydrolysis))	-	1000	-
Cl-8 (IS 17011, Table-1 (vii)(Formaldehyde)	-	1000	-
Cl-8(IS 17011, Table-1 (viii)(Organotin compounds)	-	3000	-
Cl-8 (IS 17011, Table-1 (ix)(PCP-TeCP-TriCP polychlorophenols)	-	3000	-
Cl-8 (IS 17011, Table-1 (x)(pH)	-	500	-
Cl-8 (IS 17011, Table-1 (xi)(Phthalates (each individual phthalate))	-	4500	-
Cl-8 (IS 17011, Table-1 (xii)(Nickel, on skin contact)	-	2000	-
Cl- 5.2.8.1 (Amendment No. 2)(General)	-	500	-
Cl- 5.2.8.2 (Amendment No. 2)(Internal length of toecap)	-	300	-
Cl- 5.2.8.3 (Amendment No. 2)(Corrosion resistance)	-	500	-
Cl- 5.2.9.5 (Amendment No. 2)(Breaking load and tag retention)	-	500	-
Cl- 5.2.9.6.1 (Amendment No. 2)(Abrasion resistance- Lace to lace)	-	800	-
Cl- 5.2.9.6.2 (Amendment No. 2)(Abrasion resistance- Lace to eyelet)	-	800	-
Cl- 5.2.10 (Amendment No. 2)(Force required to pull out the eyelets)	-	500	-
Cl- 5.2.12.1 (Amendment No. 2)(Insole- Material and thickness)	-	800	-
Cl- 5.2.12.2 (Amendment No. 2)(Insole- Abrasion resistance)	-	800	-
Cl- 5.2.12.3 (Amendment No. 2)(Insole- Water absorption and desorption)	-	800	-
Cl- 5.2.13.1 (Amendment No. 2)(Insock- Abrasion resistance)	-	800	-
Cl- 5.2.13.2 (Amendment No. 2)(Insock- Water absorption and desorption)	-	800	-

15 Apr, 2027

-
Included w.e.f 08.12.2025

1510

EMC Testing and Compliance LLP, Gurugram

8141526

IS 17681 (2022)

Specification for Bottled water dispensers

210000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Construction)	-	5000	-
4.1(General Design)	-	500	-
4.2(Materials)	-	500	-
4.3(Finish)	-	500	-
4.4(Thermal Insulation)	-	500	-
4.5(Hardware)	-	500	-
4.6(Disposal of Waste Water)	-	500	-
4.7(Hot Water Tank)	-	500	-
4.8(Hermetically Sealed Compressor)	-	500	-
4.9(Protective Guards)	-	500	-
5(Refrigeration System)	-	5000	-
5.1(Pipes and Connections/Fitting)	-	500	-
5.2(Control of Operation)	-	500	-
6.1(General)	-	1500	-
6.1(Protection against electric shock (Cl. 8 of IS 302-2-24))	-	3000	-
6.1(Power Input & Current (Cl. 10 of IS 302-2-24))	-	4500	-
6.1(Temperature Rise/ Heating (Cl. 11 of IS 302-2-24))	-	5500	-
6.1("Insulation Resistance and Electric Strength/ Leakage Current and Electric Strength (Cl. 13 of IS 302-2-24)")	-	3000	-
6.1("Moisture Resistance (Cl. 15 of IS 302-2-24)")	-	3500	-
6.1("Insulation resistance and electric strength (After humidity treatment) (Cl. 16 of IS 302-2-24)")	-	3000	-
6.1("Provision For Earthing (Cl. 27 of IS 302-2-24)")	-	3500	-
6.1("Screws & Connections (Cl. 28 of IS 302-2-24)")	-	2500	-
6.2(Electrical Accessories)	-	1500	-
6.3(Salt Mist Test)	-	30000	-
7(Sound pressure level)	-	15000	-
10.1(Cooling Capacity Test)	-	22000	-
10.2(Maximum Operating Condition Test (Environmental))	-	15000	-
10.3(Maximum Operating Condition Test (Voltage))	-	17000	-
10.4(Heating Capacity Test)	-	17500	-
10.5(Annual Energy Consumption Test)	-	35000	-
10.6(Freeze-up Test)	-	20000	-
10.7(Door Opening and Closing Test)	-	8000	-
10.8(Door Seal Test)	-	2000	-
10.9(Pull-down Test)	-	12000	-
11(Marking and instruction)	-	1000	-

19 Jul, 2027

-
Included w.e.f.11.09.2025

1511

EMC Testing and Compliance LLP, Gurugram

8141526

IS 1475 (2024)

Drinking Water Coolers - Specification (Fourth Revision)

50000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Classification)	-	1000	-
5(Construction)	-	1000	-
6.3(Cooling Capacity Test)	-	10000	-
6.4(Maximum Operating Condition Test)	-	6000	-
6.5(Pull Down Test)	-	5000	-
9(Maximum Power Consumption Test)	-	5000	-
10(Annual Energy Consumption Test)	-	10000	-
11(Storage Capacity Test)	-	2000	-
13(Functional Test)	-	2000	-
14 a)(Protection against electric shock)	-	2000	-
14 b)(High voltage (electric strength) test)	-	2000	-
14 c)(Leakage current tests)	-	2000	-
14 d)(Provision for earthing)	-	2000	-

19 Jul, 2027

-
Included w.e.f.11.09.2025

1512

GLOBAL COMPLIANCE LABORATORY INDIA, GHAZIABAD

5172706

IS 302 : Part 2 : Sec 203 (1994)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 203 electric call bells and buzzers for indoor use

35000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Rating)	-	3000	-
6(Classification)	-	3000	-
7(Marking)	-	3000	-
8(Protection against Access to Live Parts)	-	3000	-
11(Temperature Rise/ Heating)	-	3000	-
13(Leakage Current and Electric Strength at Operating Temperature)	-	3000	-
14("Radio and Television Interference Suppression / Transient Over Voltage ")	-	3000	-
15(Moisture Resistance)	-	3000	-
16(Leakage Current and Electric Strength/ Insulation Resistance and Electric Strength (After Humidity treatment))	-	3000	-
21(Mechanical strength)	-	3000	-
22(Construction)	-	3000	-
23(Internal Wiring)	-	3000	-
25(Supply Connection & External Flexible Cords)	-	3000	-
26(Terminals For External Conductors)	-	3000	-
27(Provision For Earthing)	-	3000	-
28(Screws & Connections)	-	3000	-
29(Clearances, Creepage Distances & Solid Insulation)	-	3000	-
30(Resistance to Heat & Fire)	-	3000	-
31(Resistance to Rusting)	-	3000	-
32(Radiation hazards)	-	3000	-

20 Jun, 2026

-
Included w.e.f. 06.10.2025 Exclusion: "10 (""Power Input & Current"") 12 (Operation Under Overload Conditions of Appliances with heating Element) 17 (Overload Protection/ Overload Protection of Transformers & Associated Circuits) 18 (Endurance) 19 (Abnormal Operation) 20 (Stability & Mechanical Hazards) 24 (Components) 9 (Starting Of Motor Operated Appliances) Cl 19.11.4.1 (Electrostatic discharges) Cl 19.11.4.2 (Radiated fields) Cl 19.11.4.3 (Fast transient bursts) Cl 19.11.4.4 (Surge immunity test) Cl 19.11.4.5 (Immunity to conducted discharges) Cl 19.11.4.6 (Class 3 Voltage dips and interruptions) Cl 19.11.4.7 (Harmonics) "

1513

ALPHA TEST HOUSE PVT LTD, BAHADURGARH

8185306

IS 14252 (2015)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sack for filling sand – Specification (second revision)

All

16500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Raw Material)	-	700	-
3.2(Tapes – Width )	-	700	-
3.2(Tapes – Linear Density )	-	700	-
3.3(Tying Cord)	-	700	-
3.3(Tying Cord)	-	700	-
3.3(Tying Cord)	-	700	-
3.4(Sack)	-	700	-
3.4.1(Seam)	-	700	-
3.4.1(Seam)	-	700	-
3.4.1(Seam)	-	700	-
3.4.1(Seam)	-	700	-
4.1 and Table 1 i a(Dimensions Outside Length)	-	700	-
4.1 and Table 1 i b(Dimensions Outside Width)	-	700	-
4.1 and Table 1 ii(Ends per dm )	-	700	-
4.1 and Table 1 iii(Picks per dm )	-	700	-
4.2 and Table 1 iv(Mass of sack )	-	700	-
4.1 and Table 1 v a(Average breaking strength of fabric Warpway )	-	700	-
4.1 and Table 1 v b(Average breaking strength of fabric Weftway )	-	700	-
4.1 and Table 1 vi(Average Breaking strength of bottom seam )	-	700	-
4.1 and Table 1 vii a(Elongation at break of fabric Lengthwise)	-	800	-
4.1 and Table 1 vii b(Elongation at break of fabric Widthwise )	-	800	-
4.1 and Table 1 viii(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	800	-
4.1 and Table 1 ix(Ash content )	-	800	-
3.1(Raw Material)	-	0	-
3.2(Tapes – Width )	-	0	-
3.2(Tapes – Linear Density )	-	0	-
3.3(Tying Cord)	-	0	-
3.3(Tying Cord)	-	0	-
3.3(Tying Cord)	-	0	-
3.4(Sack)	-	0	-
3.4.1(Seam)	-	0	-
3.4.1(Seam)	-	0	-
3.4.1(Seam)	-	0	-
3.4.1(Seam)	-	0	-
4.1 and Table 1 i a(Dimensions Outside Length)	-	0	-
4.1 and Table 1 i b(Dimensions Outside Width)	-	0	-
4.1 and Table 1 ii(Ends per dm )	-	0	-
4.1 and Table 1 iii(Picks per dm )	-	0	-
4.2 and Table 1 iv(Mass of sack )	-	0	-
4.1 and Table 1 v a(Average breaking strength of fabric Warpway )	-	0	-
4.1 and Table 1 v b(Average breaking strength of fabric Weftway )	-	0	-
4.1 and Table 1 vi(Average Breaking strength of bottom seam )	-	0	-
4.1 and Table 1 vii a(Elongation at break of fabric Lengthwise)	-	0	-
4.1 and Table 1 vii b(Elongation at break of fabric Widthwise )	-	0	-
4.1 and Table 1 viii(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	0	-
4.1 and Table 1 ix(Ash content )	-	0	-
3.2 (Mesh size and weight is g/cm2) (amendment 3)(Mesh size and weight is g/cm2)	-	0	-
3.1(Raw Material)	-	0	-
3.2(Tapes – Width )	-	0	-
3.2(Tapes – Linear Density )	-	0	-
3.3(Tying Cord)	-	0	-
3.3(Tying Cord)	-	0	-
3.3(Tying Cord)	-	0	-
3.4(Sack)	-	0	-
3.4.1(Seam)	-	0	-
3.4.1(Seam)	-	0	-
3.4.1(Seam)	-	0	-
3.4.1(Seam)	-	0	-
4.1 and Table 1 i a(Dimensions Outside Length)	-	0	-
4.1 and Table 1 i b(Dimensions Outside Width)	-	0	-
4.1 and Table 1 ii(Ends per dm )	-	0	-
4.1 and Table 1 iii(Picks per dm )	-	0	-
4.2 and Table 1 iv(Mass of sack )	-	0	-
4.1 and Table 1 v a(Average breaking strength of fabric Warpway )	-	0	-
4.1 and Table 1 v b(Average breaking strength of fabric Weftway )	-	0	-
4.1 and Table 1 vi(Average Breaking strength of bottom seam )	-	0	-
4.1 and Table 1 vii a(Elongation at break of fabric Lengthwise)	-	0	-
4.1 and Table 1 vii b(Elongation at break of fabric Widthwise )	-	0	-
4.1 and Table 1 viii(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	0	-
4.1 and Table 1 ix(Ash content )	-	0	-
3.1(Raw Material)	-	0	-
3.2(Tapes – Width )	-	0	-
3.2(Tapes – Linear Density )	-	0	-
3.3(Tying Cord)	-	0	-
3.3(Tying Cord)	-	0	-
3.3(Tying Cord)	-	0	-
3.4(Sack)	-	0	-
3.4.1(Seam)	-	0	-
3.4.1(Seam)	-	0	-
3.4.1(Seam)	-	0	-
3.4.1(Seam)	-	0	-
4.1 and Table 1 i a(Dimensions Outside Length)	-	0	-
4.1 and Table 1 i b(Dimensions Outside Width)	-	0	-
4.1 and Table 1 ii(Ends per dm )	-	0	-
4.1 and Table 1 iii(Picks per dm )	-	0	-
4.2 and Table 1 iv(Mass of sack )	-	0	-
4.1 and Table 1 v a(Average breaking strength of fabric Warpway )	-	0	-
4.1 and Table 1 v b(Average breaking strength of fabric Weftway )	-	0	-
4.1 and Table 1 vi(Average Breaking strength of bottom seam )	-	0	-
4.1 and Table 1 vii a(Elongation at break of fabric Lengthwise)	-	0	-
4.1 and Table 1 vii b(Elongation at break of fabric Widthwise )	-	0	-
4.1 and Table 1 viii(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	0	-
4.1 and Table 1 ix(Ash content )	-	0	-
3.2 (Mesh size and weight is g/cm2) (amendment 3)(Mesh size and weight is g/cm2)	-	0	-

08 May, 2028

-
Included w.e.f.29.09.2025

1514

URS PRODUCTS AND TESTING PVT. LTD. (A29), NOIDA

8168906

IS 4246 (2025)

DOMESTIC GAS STOVE AND BUILT IN HOB FOR USE WITH LPG SPECIFICATION (Sixth Revision )

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(General - IS 4246 : 2025)	-	500	-
4.1(General - IS 4246 : 2025)	-	500	-
4.1.1(General - IS 4246 : 2025)	-	500	-
5(Materials - Cl. 5 of IS 5116)	-	500	-
5.1.1(Materials - Toughened glass, if provided,)	-	500	-
5.1.1(Materials - Toughened glass, if provided,)	-	500	-
5.1.1(Materials - Toughened glass, if provided,)	-	500	-
5.1.1(Materials - Toughened glass, if provided,)	-	500	-
5.1.1(Materials - Toughened glass, if provided,)	-	500	-
5.1.1(Materials - Toughened glass, if provided,)	-	500	-
5.1.1(Materials - Toughened glass, if provided,)	-	500	-
5.1.1(Materials - Toughened glass, if provided,)	-	500	-
5.1.1(Materials - Toughened glass, if provided,)	-	500	-
5.1(Materials - IS 5116)	-	500	-
5.1(Materials - IS 5116)	-	500	-
5.1.1(Materials - IS 5116)	-	500	-
5.1.1(Materials - IS 5116)	-	500	-
5.2(Materials - IS 5116)	-	500	-
5.2(Materials - IS 5116)	-	500	-
5.3(Materials - IS 5116)	-	500	-
5.5(Materials - IS 5116)	-	500	-
5.5(Materials - IS 5116)	-	500	-
5.5(Materials - IS 5116)	-	500	-
5.7(Materials - IS 5116)	-	500	-
6.1(Design for Maintainance)	-	500	-
6.1(Design for Maintainance)	-	500	-
6.2(Design for Maintainance)	-	500	-
6.2(Design for Maintainance)	-	500	-
6.3(Design for Maintainance)	-	500	-
6.4(Design for Maintainance)	-	500	-
6.5(Design for Maintainance)	-	500	-
6.6(Design for Maintainance)	-	500	-
7.0(Rigidity and Stability)	-	500	-
7.1(Rigidity and Stability)	-	500	-
7.2(Rigidity and Stability)	-	500	-
7.3(Rigidity and Stability)	-	500	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	500	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	500	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	500	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	500	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	500	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	500	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	500	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	500	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	500	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	500	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	500	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	500	-
8.2(Workmanship and Finish -)	-	500	-
8.3(Workmanship and Finish -)	-	500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	500	-
10(Injector Jets)	-	500	-
10(Injector Jets)	-	500	-
10(Injector Jets)	-	500	-
10(Injector Jets)	-	500	-
10(Injector Jets)	-	500	-
10(Injector Jets)	-	500	-
11.1(Burners- Cl. 10 of IS 5116)	-	500	-
11.1(Burners- Cl. 10 of IS 5116)	-	500	-
11.1(Burners- Cl. 10 of IS 5116)	-	500	-
11.1(Burners- Cl. 10 of IS 5116)	-	500	-
11.1(Burners- Cl. 10 of IS 5116)	-	500	-
11.2(Burners)	-	500	-
11.3(Burners)	-	500	-
11.4(Burners)	-	500	-
12.1(Burner Pan Support)	-	500	-
12.2(Burner Pan Support)	-	500	-
12.3(Burner Pan Support)	-	500	-
13.1(Gas Soundness Test - Cl. 16 of IS 5116)	-	500	-
13,2(Gas Soundness Test)	-	500	-
13.2(Gas Leak Detector)	-	500	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	500	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	500	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	500	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	500	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	500	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	500	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	500	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	500	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	500	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	500	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	500	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	500	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	500	-
14.2(Gas Inlet Connection)	-	500	-
14.2(Gas Inlet Connection)	-	500	-
14.2(Gas Inlet Connection)	-	500	-
14.2(Gas Inlet Connection)	-	500	-
14.3(Gas Inlet Connection)	-	500	-
14.4(Gas Inlet Connection)	-	500	-
14.5(Gas Inlet Connection - Cl. 17.3 of IS 5116)	-	500	-
14.6(Gas Inlet Connection)	-	500	-
15.0(Strength and Rigidity)	-	500	-
15.0(Strength and Rigidity)	-	500	-
15.0(Strength and Rigidity)	-	500	-
15.0(Strength and Rigidity)	-	500	-
17.0(Gas Consumption Test)	-	500	-
17.0(Gas Consumption Test)	-	500	-
17.0(Gas Consumption Test)	-	500	-
17.0(Gas Consumption Test)	-	500	-
17.0(Gas Consumption Test)	-	500	-
17.0(Gas Consumption Test)	-	500	-
17.2(Gas Consumption Test - For Gas Stoves)	-	500	-
17.2 (a)(Gas Consumption Test - For Gas Stoves)	-	500	-
17.2 (b)(Gas Consumption Test - For Gas Stoves)	-	500	-
17.2 (c)(Gas Consumption Test - For Gas Stoves)	-	500	-
17.3(Gas Consumption Test - For Built in Hobs)	-	500	-
17.3.1(Gas Consumption Test - For Built in Hobs)	-	500	-
17.3.2(Gas Consumption Test - For Built in Hobs)	-	500	-
18.1(Ignition and Flame Travel)	-	500	-
18.1(Ignition and Flame Travel)	-	500	-
18.2(Ignition and Flame Travel)	-	500	-
18.3(Ignition and Flame Travel)	-	500	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	500	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	500	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	500	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	500	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	500	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	500	-
19.1(Flame Stability)	-	500	-
19.1.1(Flame Stability)	-	500	-
19.2(Flame Stability)	-	500	-
19.3(Flame Stability)	-	500	-
20(Noise Control)	-	500	-
21(Flash Back)	-	500	-
22(Formation of Soot)	-	500	-
23(Resistance to Draught)	-	500	-
24.1(Combustion)	-	500	-
24.1(Combustion)	-	500	-
24.2(Combustion)	-	500	-
25.1(Fire Hazard and Limiting Temperatures)	-	500	-
25.1(Fire Hazard and Limiting Temperatures)	-	500	-
25.1(Fire Hazard and Limiting Temperatures)	-	500	-
25.1(Fire Hazard and Limiting Temperatures)	-	500	-
25.2(Fire Hazard and Limiting Temperatures)	-	500	-
26.1(Thermal Efficiency- Gas Stoves)	-	500	-
26.1(Thermal Efficiency- Gas Stoves)	-	500	-
26.1(Thermal Efficiency- Gas Stoves)	-	500	-
26.1(Thermal Efficiency- Gas Stoves)	-	500	-
26.1(Thermal Efficiency- Gas Stoves)	-	500	-
26.2(Thermal Efficiency- For Built in Hobs)	-	500	-
26.2(Thermal Efficiency- For Built in Hobs)	-	500	-
26.2(Thermal Efficiency- For Built in Hobs)	-	500	-
26.2(Thermal Efficiency- For Built in Hobs)	-	500	-
26.2(Thermal Efficiency- For Built in Hobs)	-	500	-

26 Sep, 2027

-
Included w.e.f 11.09.2025

1515

Gravitas Laboratories Private Limited, Greater Noida

8182606

IS 7092 : Part 1 (1992)

Aluminium alloy tubes for irrigation purposes - Specification: Part 1 welded tubes (Second Revision)

All Designation

16500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10(Marking)	-	0	-
5(Workmanship and Finish)	-	4000	-
8(Dimensions)	-	4500	-
7.2(Mechanical properties)	-	4000	-
7.3(Flattening test)	-	4000	-
7.4(Hydrostatic test)	-	0	(Testing Charge 16000)
10(Marking)	-	0	-
5(Workmanship and Finish)	-	0	-
8(Dimensions)	-	0	-
7.2(Mechanical properties)	-	0	-
7.3(Flattening test)	-	0	-
7.4(Hydrostatic test)	-	0	-
10(Marking)	-	0	-
5(Workmanship and Finish)	-	0	-
8(Dimensions)	-	0	-
7.2(Mechanical properties)	-	0	-
7.3(Flattening test)	-	0	-
7.4(Hydrostatic test)	-	0	-

19 Nov, 2027

-
Included w.e.f 09.10.2025

1516

Bombay Textiles Research Association (BTRA), Mumbai

7130206

IS 702 (2022)

SPECIFICATION FOR INDUSTRIAL BITUMEN

Industrial Bitumen

37500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6-Table 1-i)(Specific gravity at 27 °C)	-	2500	-
6-Table 1-ii)(Flash point, Cleveland open cup, °C, Min)	-	2500	-
6-Table 1-iii)(Softening point, °C)	-	5000	-
6-Table 1-iv)(Penetration at 25 °C, 100g, 5 sec, 1/10 mm)	-	5000	-
6-Table 1-v)(a) Loss on heating, percent by mass, Min b) Penetration of the residue at 25 °C, 100g, 5 s, percent of original, Min)	-	15000	Total Charges a and b
6-Table 1-vi)(Ductility at 27 °C, cm, Min)	-	5000	-
6-Table 1-vii)(Matter soluble in trichloroethylene, percent by mass, Min)	-	2500	-

-
Included w.e.f 09.10.2025

1517

BUREAU VERITAS CONSUMER PRODUCTS SERVICES INDIA PRIVATE LIMITED, NOIDA

8127706

IS 17631 (2022)

Work Chairs - Specification

Furniture

77000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
clause 4(DESIGN AND WORKMANSHIP)	-	1000	-
clause 5(DIMENSIONS)	-	1000	-
Cl-6.1 (a)(Resistance to mechanical damage)	-	3000	-
Cl-6.2 (a) (1)(For Fabric and Synthetic Leather:- Breaking load)	-	1000	-
Cl-7.3.1(Front Edge Overturning)	-	1000	-
Cl-7.3.2(Forwards Overturning)	-	1000	-
Cl-7.3.3(Forwards Overturning for Chairs with Foot Rest)	-	1000	-
Cl-7.3.4(Sideways Overturning for Chairs Without Arm Rests)	-	1000	-
Cl-6.1 (b)(Pencil hardness)	-	1000	-
Cl-6.1 (c)(Resistance to wet heat;)	-	2000	-
Cl-6.1 (d)(Resistance to dry heat;)	-	2000	-
Cl-6.1 (e)(Resistance to marking by cold liquids)	-	3000	-
Cl-6.1 (f)(Resistance to marking by cold oils and fats;)	-	3000	-
Cl-6.1 (g)(Adhesive performance)	-	2000	-
Cl-6.2 (a) (2)(For Fabric and Synthetic Leather:- Elongation at break)	-	1000	-
Cl-6.2 (a) (3)(For Fabric and Synthetic Leather:- Tear strength)	-	600	-
Cl-6.2 (a) (4)(For Fabric and Synthetic Leather:- Colour fastness to light)	-	1500	-
Cl-6.2 (a) (5)(For Fabric and Synthetic Leather:- Colour fastness to rubbing)	-	500	-
Cl-6.2 (a) (6)(For Fabric and Synthetic Leather:- Colour fastness to perspiration)	-	500	-
Cl-6.2 (a) (7)(For Fabric and Synthetic Leather:- Colour fastness to water)	-	500	-
Cl-6.2 (a) (8)(For Fabric and Synthetic Leather:- Pilling resistance)	-	1000	-
Cl-6.2 (a) (9)(For Fabric and Synthetic Leather:- Coating adhesion strength)	-	1100	-
Cl-6.2 (a) (10)(For Fabric and Synthetic Leather:- Seam slippage)	-	1000	-
Cl-6.2 (a) (11)(For Fabric and Synthetic Leather:- Resistance to damage by flexing)	-	1500	-
Cl-6.2 (a) (12)(For Fabric and Synthetic Leather:- Abrasion resistance)	-	1000	-
Cl-6.2 (a) (13)(For Fabric and Synthetic Leather:- Bursting strength)	-	1500	-
Cl-6.2 (a) (14)(For Fabric and Synthetic Leather:- Resistance to cold)	-	2000	-
Cl-6.2 (b) (2)(For Natural Leather:- Flexing endurance)	-	1500	-
Cl-6.2 (b) (1)(For Natural Leather:- Tear strength)	-	650	-
Cl-6.2 (b) (3)(For Natural Leather: Finish adhesion)	-	1100	-
Cl-6.2 (b) (4)(For Natural Leather: Colour fastness to artificial light)	-	1500	-
Cl-6.2 (b) (5)(For Natural Leather: Colour fastness to rubbing)	-	1000	-
Cl-6.2 (b) (6)(For Natural Leather: Colour fastness to water spotting)	-	500	-
Cl-6.2 (b) (7)(For Natural Leather: Water vapour permeability)	-	1500	-
Cl-6.2 (b) (8)(For Natural Leather: Colour fastness to water)	-	500	-
Cl-7.3.5(Sideways Overturning for Chairs With Arm Rests)	-	1000	-
Cl-7.3.6(Rearwards Overturning for Chairs Without Back Rest Inclination)	-	1000	-
Cl-7.3.7(Rearwards Overturning for Chairs with Backrest Inclination)	-	1000	-
Cl-7.4.1(Seat Front Edge Static Load Test)	-	2000	-
Cl-7.4.2(Combined Seat and Back Static Load Test)	-	2000	-
Cl-7.4.3(Arm Rest Downward Static Load Test — Central)	-	2000	-
Cl-7.4.4(Arm Rest Downward Static Load Test — Front)	-	2000	-
Cl-7.4.5(Arm Rest Sideways Static Load Test)	-	2000	-
Cl-7.4.6(Foot Rest Static Load Test)	-	2000	-
Cl-7.5.1(Seat and Back Durability)	-	18000	-
Cl-7.5.2(Arm Rest Durability)	-	8000	-
Cl-7.5.3(Swivel Test)	-	10000	-
Cl-7.5.4(Foot-rest Durability)	-	8000	-
Cl-7.5.5(Castor and Chair-Base Durability)	-	10000	-

31 Dec, 2026

-
Included w.e.f. 11.09.2025

1518

Hi Physix Laboratory India Private Limited, Pune

7126926

IS 18112 (2025)

DIGITAL TELEVISION RECEIVER FOR SATELLITE BROADCAST TRANSMISSION SPECIFICATION (First Revision)

428000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4.4, Table-2, ii)(RF characteristics to be supported by the DTV receiver)	-	0	-
Clause 4.3(Specifications)	-	50000	Separately covered as per IS 616
Clause 4.5(Safety Requirements)	-	0	-
Clause 4.6(Electromagnetic Compatibility (EMC) Requirements)	-	140000	-
Clause 5(Marking)	-	2000	-
Clause 6(Operating Life Test)	-	10000	-
Clause 4.1, Table-1, i) a)(Hardware specification)	-	3000	-
Clause 4.1, Table-1, i) b)(Decompression and decoding of SDTV video)	-	5000	-
Clause 4.1, Table-1, i) c)(Decompression and decoding of HDTV video)	-	5000	-
Clause 4.1, Table-1, i) d)(Decompression and decoding of audio)	-	5000	-
Clause 4.1, Table-1, i) e)(Active Format descriptors)	-	5000	-
Clause 4.1, Table-1, i) f)(Captioning and Sub-titling)	-	5000	-
Clause 4.1, Table-1, i) g)(Teletext)	-	5000	-
Clause 4.1, Table-1, i) h)(Multi-language support)	-	3000	-
Clause 4.1, Table-1, i) j)(DTV receiver mixed Audio Description)	-	3000	-
Clause 4.1, Table-1, i) k)(Broadcast mixed audio description)	-	3000	-
Clause 4.1, Table-1, i) m)(Service demultiplexing)	-	3000	-
Clause 4.1, Table-1, i) n)(Data services)	-	3000	-
Clause 4.1, Table-1, i) p)(OSD)	-	5000	-
Clause 4.1, Table-1, i) q)(DTV character set)	-	5000	-
Clause 4.1, Table-1, i) r)(Electronic Service Guide (ESG) ‘Now/Next’)	-	5000	-
Clause 4.1, Table-1, i) s)(Time)	-	5000	-
Clause 4.1, Table-1, i) t)(Digital TV output)	-	5000	-
Clause 4.4, Table-2, i) b)(Frequency)	-	5000	-
Clause 4.4, Table-2, i) a)(Input voltage range)	-	5000	-
Clause 4.1,Table-1, ii) a)(Demodulation and FEC decoding)	-	5000	-
Clause 4.1, Table-1, ii) b)(DTV Receiver Installation)	-	5000	-
Clause 4.1, Table-1, ii) c)(Network evolution)	-	5000	-
Clause 4.4, Table-2, iii) c)(RF input impedance)	-	0	-
Clause 4.1, Table-1, ii) d)(Services available)	-	5000	-
Clause 4.1, Table-1, ii) e)(Selection via Service List)	-	5000	-
Clause 4.1, Table-1, ii) f)(Selection via Numeric Entry)	-	5000	-
Clause 4.1, Table-1, ii) g)(Favourite Channel list)	-	5000	-
Clause 4.1, Table-1, ii) h)(Hidden Services)	-	5000	-
Clause 4.4, Table-2, iii) b)(Input frequency range)	-	5000	-
Clause 4.1, Table-1, ii) j)(Logical Channel Number for Satellite services)	-	5000	-
Clause 4.1, Table-1, ii) k)(RF input signal)	-	10000	-
Clause 4.1, Table-1, ii) m)(LNB supply current)	-	5000	-
Clause 4.1, Table-1, ii) n)(LNB supply voltage)	-	5000	-
Clause 4.1, Table-1, ii) p)(LNB Control)	-	5000	-
Clause 4.1, Table-1, ii) q)(Modulation/Demodulation parameters for DVB-S & DVB-S2 standard)	-	0	-
Clause 4.4, Table-2, iii) a)(Input level per carrier)	-	15000	-
Clause 4.4, Table-2, iv) c)(RF input impedance)	-	0	-
Clause 4.4, Table-2, iv) b)(Input frequency range)	-	5000	-
Clause 4.4, Table-2, iv) a)(Input level per carrier)	-	15000	-
Clause 4.4, Table-2, v)(Symbol rate)	-	5000	-
Clause 4.4, Table-2, vi)(RF input return loss)	-	0	-
Clause 4.4, Table-2, vii)(DisEqC)	-	5000	-
Clause 4.4, Table-2, viii)(Operating ambient temperature range)	-	0	-
Clause 4.4, Table-2, ix)(Operating humidity range)	-	0	-
Clause 4.1, Table-1, iii) a)(Interfaces, Connectors)	-	5000	-
Clause 4.1, Table-1, iv)(Automatic software upgrade mechanism)	-	5000	-
Clause 4.1, Table-1, v) a)(Remote Control)	-	5000	-
Clause 4.1, Table-1, v) b)(Easy to use and simple documentation)	-	5000	-
Clause 3.1, Table-1, v) c)(Support package)	-	3000	-

20 Jun, 2028

-
Included w.e.f. 13.11.2025

1519

ADS LABTECH, GHAZIABAD

8178326

IS 4985 (2021)

UNPLASTICIZED PVC PIPES FOR POTABLE WATER SUPPLIES SPECIFICATION Fourth Revision

UNPLASTICIZED PVC PIPES FOR POTABLE WATER SUPPLIES

18000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.1(Colour)	-	200	.
10.1(Surface Finish)	-	200	.
7.2.1.1 Table3(Angle of taper (Note-1))	-	300	.
10.7(Sulphated Ash Content)	-	800	.
5(CLASSIFICATION OF PIPES)	-	400	.
Cl-7.1(Mean out side Diameter (For less than or equal to 40 mm- Average of 8 , For higher diameters up to 110 mm average of 6))	-	500	.
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	500	.
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-	500	.
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. Variation)	-	500	.
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	500	.
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-	500	.
7.1.1.2(DIMENSIONS-PIPE-Ovality (Maximum))	-	500	.
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	500	.
7.1.2.1(DIMENSIONS-PIPE-Thickness(Maximum))	-	500	.
7.1.2.1(DIMENSIONS-PIPE-Average Thickness)	-	500	.
Cl- 7.2(Socket length (Take 4 reading & minimum will be reported))	-	500	.
7.2.1(DIMENSIONS-Socket)	-	500	.
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	500	.
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-	500	.
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-	500	.
7.2.1.2(a)-Table 5(DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-	500	.
7.2.1.2-Table 4(DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-	500	.
8(SEALING RINGS)	-	500	.
9.1(PIPE ENDS)	-	500	.
10.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	500	.
10.1.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	500	.
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	500	.
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	500	.
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	500	.
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	500	.
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	4000	.
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	4000	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	4000	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	4000	-
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	4000	.
11.2(Resistance to External Blows at 0°C)	-	1000	.
10.3(Effect on Water Test)	-	4000	.
Cl-10.3 (i)(Effect on Lead (first extraction))	-	4000	.
Cl-10.3 (ii)(Effect on Lead (third extraction))	-	4000	.
7.1.3(mean outside diameter, outside diameter at any point, and wall thickness of plumbing pipes)	-	500	.
7.1.4(Length)	-	500	.
7.2.1.2b(Maximum inner diameter of groove)	-	500	.
13.1(Marking)	-	200	.
cL-13.1.1(Marking)	-	200	.
Cl-13.1.2(Marking)	-	200	.
6.1.2(PVC Resin)	-	2000	.
6.1.1(VCM Content)	-	2000	.
Cl-10.3 (iii)(Effect on Dialkyl tin C4 and higher homologues measured as tin (third extraction))	-	4000	.
Cl-10.3 (iv)(Effect on Cadmium)	-	4000	.
Cl-10.3 (v)(Effect on Mercury)	-	4000	.
Cl-10.3 (vi)(Other toxic substances such as ‘di-n-octyl-tin- mass) s-s bis iso-octyl mercapto acetate’ and ‘butyl stearate)	-	4000	.
10.1(Colour)	-	500	.
10.1(Surface Finish)	-	500	.
7.2.1.1 Table3(Angle of taper (Note-1))	-	500	.
10.7(Sulphated Ash Content)	-	500	.
5(CLASSIFICATION OF PIPES)	-	500	.
Cl-7.1(Mean out side Diameter (For less than or equal to 40 mm- Average of 8 , For higher diameters up to 110 mm average of 6))	-	500	.
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	500	.
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-	500	.
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. Variation)	-	500	.
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	500	.
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-	500	.
7.1.1.2(DIMENSIONS-PIPE-Ovality (Maximum))	-	500	.
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	500	.
7.1.2.1(DIMENSIONS-PIPE-Thickness(Maximum))	-	500	.
7.1.2.1(DIMENSIONS-PIPE-Average Thickness)	-	500	.
Cl- 7.2(Socket length (Take 4 reading & minimum will be reported))	-	500	.
7.2.1(DIMENSIONS-Socket)	-	500	.
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	500	.
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-	500	.
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-	500	.
7.2.1.2(a)-Table 5(DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-	500	.
7.2.1.2-Table 4(DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-	500	.
8(SEALING RINGS)	-	500	.
9.1(PIPE ENDS)	-	500	.
10.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	500	.
10.1.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	500	.
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	500	.
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	500	.
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	500	.
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	500	.
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	500	.
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	500	.
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	500	.
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	500	.
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	500	.
11.2(Resistance to External Blows at 0°C)	-	500	.
10.3(Effect on Water Test)	-	500	..
Cl-10.3 (i)(Effect on Lead (first extraction))	-	500	.
Cl-10.3 (ii)(Effect on Lead (third extraction))	-	500	.
7.1.3(mean outside diameter, outside diameter at any point, and wall thickness of plumbing pipes)	-	500	.
7.1.4(Length)	-	500	.
7.2.1.2b(Maximum inner diameter of groove)	-	500	.
13.1(Marking)	-	500	.
cL-13.1.1(Marking)	-	500	.
Cl-13.1.2(Marking)	-	500	.
6.1.2(PVC Resin)	-	500	.
6.1.1(VCM Content)	-	500	.
Cl-10.3 (iii)(Effect on Dialkyl tin C4 and higher homologues measured as tin (third extraction))	-	500	.
Cl-10.3 (iv)(Effect on Cadmium)	-	500	.
Cl-10.3 (v)(Effect on Mercury)	-	500	.
Cl-10.3 (vi)(Other toxic substances such as ‘di-n-octyl-tin- mass) s-s bis iso-octyl mercapto acetate’ and ‘butyl stearate)	-	500	.

15 May, 2027

-
-

1520

ALPHA TEST HOUSE SERVICES LLP (Unit-1), MOHALI

9184906

IS 208 (2020)

Door Handles - Specification ( Sixth Revision )

all

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10(PACKING)	-	7500	-
9.1(BIS Certification Marking)	-	7500	-
9(MARKING)	-	7500	-
6.2(Tolerance)	-	7500	-
6.1 Table2A & 2B and Fig 1,2,3,4(DIMENSIONS - Size 1. No. in each Lug 2. No. in a plate when a continious plate is used 3. Size Designation of Counter-sunk Head Wood Screws (as per IS 6760: 1972))	-	7500	-
6.1 Table2A & 2B and Fig 1,2,3,4(DIMENSIONS - Size (A,B,C,D,E,F,G,H,I))	-	7500	-
5.1(MANUFACTURE- General)	-	7500	-
3(TYPES-Doors handle shall be of the following types according to the materials used:)	-	7500	-
4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981)(Chemical composition - Zinc- IS 2600:1964)	-	7500	-
4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981)(Chemical composition - Impurities-Nickel- IS 2600:1964)	-	7500	-
4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981)(Chemical composition - Impurities-Thallium and Indium- IS 2600:1964)	-	7500	-
4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981)(Chemical composition - Impurities-Tin- IS 2600:1964)	-	7500	-
4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981)(Chemical composition - Impurities-Cadmium- IS 2600:1964)	-	7500	-
Cl.5.1(General)	-	7500	-
Cl.6(Dimension)	-	7500	-
Cl.7(Finish)	-	7500	-
Cl.8.2(Cossosion Test)	-	7500	-
Cl.8.3(Quench Test)	-	7500	-
Cl.9(Sampling and criterion for conformity)	-	7500	-
Cl.10(Marking)	-	7500	-
Cl.11(Packing)	-	7500	-
Cl.8.3 (Amendment 1)(Anodizing Test)	-	7500	-

25 Apr, 2028

-
Included w.e.f.22.09.2025

1521

EKO PRO ENGINEERS PRIVATE LIMITED (32/37) GHAZIABAD

8164006

IS 4246 (2025)

DOMESTIC GAS STOVE AND BUILT IN HOB FOR USE WITH LPG SPECIFICATION (Sixth Revision )

ALL

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(General - IS 4246 : 2025)	-	500	-
4.1(General - IS 4246 : 2025)	-	500	-
4.1.1(General - IS 4246 : 2025)	-	500	-
5(Materials - Cl. 5 of IS 5116)	-	2000	-
5.1.1(Materials - Toughened glass, if provided,)	-	2000	-
5.1.1(Materials - Toughened glass, if provided,)	-	2000	-
5.1.1(Materials - Toughened glass, if provided,)	-	2000	-
5.1.1(Materials - Toughened glass, if provided,)	-	2000	-
5.1.1(Materials - Toughened glass, if provided,)	-	2000	-
5.1.1(Materials - Toughened glass, if provided,)	-	2000	-
5.1.1(Materials - Toughened glass, if provided,)	-	2000	-
5.1.1(Materials - Toughened glass, if provided,)	-	2000	-
5.1.1(Materials - Toughened glass, if provided,)	-	2000	-
5.1(Materials - IS 5116)	-	2000	-
5.1(Materials - IS 5116)	-	2000	-
5.1.1(Materials - IS 5116)	-	2000	-
5.1.1(Materials - IS 5116)	-	2000	-
5.2(Materials - IS 5116)	-	2000	-
5.2(Materials - IS 5116)	-	2000	-
5.3(Materials - IS 5116)	-	2000	-
5.5(Materials - IS 5116)	-	2000	-
5.5(Materials - IS 5116)	-	2000	-
5.5(Materials - IS 5116)	-	2000	-
5.7(Materials - IS 5116)	-	2000	-
6.1(Design for Maintainance)	-	1000	-
6.1(Design for Maintainance)	-	1000	-
6.2(Design for Maintainance)	-	1000	-
6.2(Design for Maintainance)	-	1000	-
6.3(Design for Maintainance)	-	1000	-
6.4(Design for Maintainance)	-	1000	-
6.5(Design for Maintainance)	-	1000	-
6.6(Design for Maintainance)	-	1000	-
7.0(Rigidity and Stability)	-	1000	-
7.1(Rigidity and Stability)	-	1000	-
7.2(Rigidity and Stability)	-	1000	-
7.3(Rigidity and Stability)	-	1000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	1000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	1000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	1000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	1000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	1000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	1000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	1000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	1000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	1000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	1000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	1000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	1000	-
8.2(Workmanship and Finish -)	-	1000	-
8.3(Workmanship and Finish -)	-	1000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1000	-
10(Injector Jets)	-	2000	-
10(Injector Jets)	-	2000	-
10(Injector Jets)	-	2000	-
10(Injector Jets)	-	2000	-
10(Injector Jets)	-	2000	-
10(Injector Jets)	-	2000	-
11.1(Burners- Cl. 10 of IS 5116)	-	2000	-
11.1(Burners- Cl. 10 of IS 5116)	-	2000	-
11.1(Burners- Cl. 10 of IS 5116)	-	2000	-
11.1(Burners- Cl. 10 of IS 5116)	-	2000	-
11.1(Burners- Cl. 10 of IS 5116)	-	2000	-
11.2(Burners)	-	2000	-
11.3(Burners)	-	2000	-
11.4(Burners)	-	2000	-
12.1(Burner Pan Support)	-	2000	-
12.2(Burner Pan Support)	-	2000	-
12.3(Burner Pan Support)	-	2000	-
13.1(Gas Soundness Test - Cl. 16 of IS 5116)	-	2000	-
13,2(Gas Soundness Test)	-	2000	-
13.2(Gas Leak Detector)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.2(Gas Inlet Connection)	-	2000	-
14.2(Gas Inlet Connection)	-	2000	-
14.2(Gas Inlet Connection)	-	2000	-
14.2(Gas Inlet Connection)	-	2000	-
14.3(Gas Inlet Connection)	-	2000	-
14.4(Gas Inlet Connection)	-	2000	-
14.5(Gas Inlet Connection - Cl. 17.3 of IS 5116)	-	2000	-
14.6(Gas Inlet Connection)	-	2000	-
15.0(Strength and Rigidity)	-	2000	-
15.0(Strength and Rigidity)	-	2000	-
15.0(Strength and Rigidity)	-	2000	-
15.0(Strength and Rigidity)	-	2000	-
17.0(Gas Consumption Test)	-	2000	-
17.0(Gas Consumption Test)	-	2000	-
17.0(Gas Consumption Test)	-	2000	-
17.0(Gas Consumption Test)	-	2000	-
17.0(Gas Consumption Test)	-	2000	-
17.0(Gas Consumption Test)	-	2000	-
17.2(Gas Consumption Test - For Gas Stoves)	-	2000	-
17.2 (a)(Gas Consumption Test - For Gas Stoves)	-	2000	-
17.2 (b)(Gas Consumption Test - For Gas Stoves)	-	2000	-
17.2 (c)(Gas Consumption Test - For Gas Stoves)	-	2000	-
17.3(Gas Consumption Test - For Built in Hobs)	-	2000	-
17.3.1(Gas Consumption Test - For Built in Hobs)	-	2000	-
17.3.2(Gas Consumption Test - For Built in Hobs)	-	2000	-
18.1(Ignition and Flame Travel)	-	2000	-
18.1(Ignition and Flame Travel)	-	2000	-
18.2(Ignition and Flame Travel)	-	2000	-
18.3(Ignition and Flame Travel)	-	2000	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	2000	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	2000	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	2000	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	2000	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	2000	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	2000	-
19.1(Flame Stability)	-	2000	-
19.1.1(Flame Stability)	-	2000	-
19.2(Flame Stability)	-	2000	-
19.3(Flame Stability)	-	2000	-
20(Noise Control)	-	2000	-
21(Flash Back)	-	2000	-
22(Formation of Soot)	-	2000	-
23(Resistance to Draught)	-	2000	-
24.1(Combustion)	-	2000	-
24.1(Combustion)	-	2000	-
24.2(Combustion)	-	2000	-
25.1(Fire Hazard and Limiting Temperatures)	-	2000	-
25.1(Fire Hazard and Limiting Temperatures)	-	2000	-
25.1(Fire Hazard and Limiting Temperatures)	-	2000	-
25.1(Fire Hazard and Limiting Temperatures)	-	2000	-
25.2(Fire Hazard and Limiting Temperatures)	-	2000	-
26.1(Thermal Efficiency- Gas Stoves)	-	2000	-
26.1(Thermal Efficiency- Gas Stoves)	-	2000	-
26.1(Thermal Efficiency- Gas Stoves)	-	2000	-
26.1(Thermal Efficiency- Gas Stoves)	-	2000	-
26.1(Thermal Efficiency- Gas Stoves)	-	2000	-
26.2(Thermal Efficiency- For Built in Hobs)	-	2000	-
26.2(Thermal Efficiency- For Built in Hobs)	-	2000	-
26.2(Thermal Efficiency- For Built in Hobs)	-	2000	-
26.2(Thermal Efficiency- For Built in Hobs)	-	2000	-
26.2(Thermal Efficiency- For Built in Hobs)	-	2000	-

27 May, 2028

-
Included w.e.f 08.12.2025

1522

ALPHA TEST HOUSE SERVICES LLP (Unit-1), MOHALI

9184906

IS 4992 (2024)

Door Handles for Mortice Locks â Specification (Second Revision)

All

19500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-6.1(Fastening Elements and Spindle)	-	19500	-
Cl-6.2, Table-2 (i) a(Axial strength percent)	-	19500	-
Cl-6.2, Table-2 (i) b(Pre-load)	-	19500	-
Cl-6.2, Table-2 (i) c(Permanent deformation)	-	19500	-
Cl-6.3(Safety Requirements)	-	19500	-
Cl-6.4, Table-3 (1) a(Number of cycles)	-	19500	-
Cl-6.4, Table-3 (1) b(Force “P”)	-	19500	-
Cl-6.5(Corrosion Resistance)	-	19500	-
Cl-8(Marking)	-	19500	-

25 Apr, 2028

-
Included w.e.f.28.08.2025 Exclusion Cl-6.6 (Fire Resistance Test)

1523

National Research and Technology Consortium (NRTC), Parwanoo

9136024

IS 4250 (2025)

Electric Food-Mixers (Liquidizers and Grinders) and Centrifugal Juicers ï¿½ Specification ( Second Revision )

25000 View breakup
-

Clause No.	Exclusion	Remark
Cl-4(General Requirements)	-	included
Cl-5(General Conditions for the tests)	-	included
Cl-6(Classification)	-	included
Cl-7(Marking)	-	included
Cl-8(Safety Requirements)	-	included
Cl-9(Endurance fpr motor and base assembly)	-	included
Cl-10.2("Grinding Coffee (for Machines that Have a Dry Grinding Arrangement)")	-	included
Cl-10.3(Whisking Egg Whites (for Machines that have Whisking Egg Arrangement))	-	included
Cl-10.4(Idli Batter)	-	included
Cl-10.5(Operational Tests for Juicers)	-	included
Cl-11(Temperature Withstand Test for Bowl)	-	included
Cl-12.1(Test for Switches)	-	included
Cl-13(Strength of Assembly)	-	included
Cl-14.2, 14.3 Table-2 (i)(Protection against access to live parts)	-	included
Cl-14.2, Table-2 (ii)(Power input and current)	-	included
Cl-14.2, 14.3 Table-2 (iii)(Leakage current and electric strength at operating temperature)	-	included
Cl-14.2, Table-2 (iv)(Moisture resistance)	-	included
Cl-14.2, Table-2 (v)(Leakage current and electric strength)	-	included
Cl-14.2, 14.3 Table-2 (vi)(Provision for earthing)	-	included
Cl-4(General Requirements)	-	included
Cl-5(General Conditions for the tests)	-	included
Cl-6(Classification)	-	included
Cl-7(Marking)	-	included
Cl-8(Safety Requirements)	-	included
Cl-9(Endurance fpr motor and base assembly)	-	included
Cl-10.2("Grinding Coffee (for Machines that Have a Dry Grinding Arrangement)")	-	included
Cl-10.3(Whisking Egg Whites (for Machines that have Whisking Egg Arrangement))	-	included
Cl-10.4(Idli Batter)	-	included
Cl-10.5(Operational Tests for Juicers)	-	included
Cl-11(Temperature Withstand Test for Bowl)	-	included
Cl-12.1(Test for Switches)	-	included
Cl-13(Strength of Assembly)	-	included
Cl-14.2, 14.3 Table-2 (i)(Protection against access to live parts)	-	included
Cl-14.2, Table-2 (ii)(Power input and current)	-	included
Cl-14.2, 14.3 Table-2 (iii)(Leakage current and electric strength at operating temperature)	-	included
Cl-14.2, Table-2 (iv)(Moisture resistance)	-	included
Cl-14.2, Table-2 (v)(Leakage current and electric strength)	-	included
Cl-14.2, 14.3 Table-2 (vi)(Provision for earthing)	-	included
Cl-4(General Requirements)	-	included
Cl-5(General Conditions for the tests)	-	included
Cl-6(Classification)	-	included
Cl-7(Marking)	-	included
Cl-8(Safety Requirements)	-	included
Cl-9(Endurance fpr motor and base assembly)	-	included
Cl-10.2("Grinding Coffee (for Machines that Have a Dry Grinding Arrangement)")	-	included
Cl-10.3(Whisking Egg Whites (for Machines that have Whisking Egg Arrangement))	-	included
Cl-10.4(Idli Batter)	-	included
Cl-10.5(Operational Tests for Juicers)	-	included
Cl-11(Temperature Withstand Test for Bowl)	-	included
Cl-12.1(Test for Switches)	-	included
Cl-13(Strength of Assembly)	-	included
Cl-14.2, 14.3 Table-2 (i)(Protection against access to live parts)	-	included
Cl-14.2, Table-2 (ii)(Power input and current)	-	included
Cl-14.2, 14.3 Table-2 (iii)(Leakage current and electric strength at operating temperature)	-	included
Cl-14.2, Table-2 (iv)(Moisture resistance)	-	included
Cl-14.2, Table-2 (v)(Leakage current and electric strength)	-	included
Cl-14.2, 14.3 Table-2 (vi)(Provision for earthing)	-	included

10 Apr, 2026

-
Included w.e.f.10.09.2025 Exclusion Cl 19.11.4.1 To Cl 19.11.4.7 EMI/EMC

1524

ALPHA TEST HOUSE PVT LTD, BAHADURGARH

8185306

IS 7056 (2024)

Textiles ï¿½ Cotton Towelling and Towels ï¿½ Specification (Second revison)

All

45000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-3.1, Table-1(Count of Yarn, Ne)	-	830	-
Cl-3.1, Table-1(Threads per dm, Min)	-	830	-
Cl-3.1, Table-1(Mass, Min)	-	830	-
Cl-3.1, Table-1(Terry Ratio, Min)	-	830	-
Cl-3.1, Table-2(Count of Yarn, Ne)	-	830	-
Cl-3.1, Table-2(Threads per dm Min)	-	830	-
Cl-3.1, Table-2(Mass, Min)	-	830	-
Cl-3.2.1, Table-3 (i)(Identification of material)	-	830	-
Cl-3.2.1, Table-3 (ii)(Breaking load on 5.0 cm × 20 cm strips Min)	-	830	-
Cl-3.2.1, Table-3 (iii)(Scouring loss, percent, Max)	-	830	-
Cl-3.2.1, Table-3 (iv)(Dimensional change, percent, Max)	-	830	-
Cl-3.2.1, Table-3 (v)(pH value)	-	830	-
Cl-3.2.1, Table-3 (vi)(Wettability, Max)	-	830	-
Cl-3.2.1, Table-3 (vii), a(Minimum Colour Fastness Rating to Light)	-	830	-
Cl-3.2.1, Table-3 (vii), b(Minimum Colour Fastness Rating to Washing)	-	830	-
Cl-3.2.1, Table-3 (vii), c(Minimum Colour Fastness Rating to Hypochlorite)	-	830	-
Cl-3.2.2(Whiteness index)	-	830	-
Cl-3.3(Freedom from Defects)	-	830	-
Cl-3.4, Table-4(Minimum Dimensions-Width)	-	830	-
Cl-3.4, Table-4(Minimum Dimensions-Length)	-	830	-
Cl-3.5, Table-4(Maximum depth of plain heading)	-	830	-
Cl-3.6 (a)(Cotton sewing thread)	-	830	-
Cl-3.6 (b)(Polyester sewing thread)	-	830	-
Cl-3.7(Transverse Ends or End Hems)	-	830	-
Cl-3.8(Side Edges)	-	830	-
Cl-3.9(Stitching)	-	830	-
Cl-5(Marking)	-	830	-
Cl-3.1, Table-1(Count of Yarn, Ne- Warp, Ground, Pile Weft)	-	830	-
Cl-3.1, Table-1(Threads per dm, Min- Warp, Ground, Pile Weft)	-	830	-
Cl-3.1, Table-1(Mass, Min g/m2)	-	830	-
Cl-3.1, Table-1(Terry Ratio, Min)	-	830	-
Cl-3.1, Table-2(Count of Yarn, Ne- Warp)	-	830	-
Cl-3.1, Table-2(Count of Yarn, Ne- Weft)	-	830	-
Cl-3.1, Table-2(Threads per dm Min- Ends)	-	830	-
Cl-3.1, Table-2(Threads per dm Min- Picks)	-	830	-
Cl-3.1, Table-2(Mass, Min g/m2)	-	830	-
Cl-3.2.1, Table-3 (i)(Identification of material)	-	830	-
Cl-3.2.1, Table-3 (ii)("Breaking load on 5.0 cm × 20 cm strips a) Warpway")	-	830	-
Cl-3.2.1, Table-3 (ii)("Breaking load on 5.0 cm × 20 cm strips b) Weftway")	-	830	-
Cl-3.2.1, Table-3 (iii)(Scouring loss, percent, Max)	-	830	-
Cl-3.2.1, Table-3 (iv)(Dimensional change, percent, Max)	-	830	-
Cl-3.2.1, Table-3 (v)(pH value)	-	830	-
Cl-3.2.1, Table-3 (vi)(Wettability, Max)	-	830	-
Cl-3.2.1, Table-3 (vii)(Minimum colour fastness rating to: a) Light)	-	830	-
Cl-3.2.1, Table-3 (vii)(Minimum colour fastness rating to: b) Washing)	-	830	-
Cl-3.2.1, Table-3 (vii)(Minimum colour fastness rating to: c) Hypochlorite)	-	830	-
Cl-3.3(Freedom from Defects)	-	830	-
Cl-3.4, 3.5, Table-4(Minimum Dimensions- Width)	-	830	-
Cl-3.4, 3.5, Table-4(Minimum Dimensions- Length)	-	830	-
Cl-3.4, 3.5, Table-4(Maximum Heading)	-	830	-
Cl-3.7(Transverse Ends or End Hems)	-	830	-
Cl-3.8(Side Edges)	-	830	-
Cl-3.9(Stitching)	-	830	-
Cl-5(Marking)	-	830	-
Cl-3.1, Table-1(Count of Yarn, Ne)	-	830	-
Cl-3.1, Table-1(Threads per dm, Min)	-	830	-
Cl-3.1, Table-1(Mass, Min)	-	830	-
Cl-3.1, Table-1(Terry Ratio, Min)	-	830	-
Cl-3.1, Table-2(Count of Yarn, Ne)	-	830	-
Cl-3.1, Table-2(Threads per dm Min)	-	830	-
Cl-3.1, Table-2(Mass, Min)	-	830	-
Cl-3.2.1, Table-3 (i)(Identification of material)	-	830	-
Cl-3.2.1, Table-3 (ii)(Breaking load on 5.0 cm × 20 cm strips Min)	-	830	-
Cl-3.2.1, Table-3 (iii)(Scouring loss, percent, Max)	-	830	-
Cl-3.2.1, Table-3 (iv)(Dimensional change, percent, Max)	-	830	-
Cl-3.2.1, Table-3 (v)(pH value)	-	830	-
Cl-3.2.1, Table-3 (vi)(Wettability, Max)	-	830	-
Cl-3.2.1, Table-3 (vii), a(Minimum Colour Fastness Rating to Light)	-	830	-
Cl-3.2.1, Table-3 (vii), b(Minimum Colour Fastness Rating to Washing)	-	830	-
Cl-3.2.1, Table-3 (vii), c(Minimum Colour Fastness Rating to Hypochlorite)	-	830	-
Cl-3.2.2(Whiteness index)	-	830	-
Cl-3.3(Freedom from Defects)	-	830	-
Cl-3.4, Table-4(Minimum Dimensions-Width)	-	830	-
Cl-3.4, Table-4(Minimum Dimensions-Length)	-	830	-
Cl-3.5, Table-4(Maximum depth of plain heading)	-	830	-
Cl-3.6 (a)(Cotton sewing thread)	-	830	-
Cl-3.6 (b)(Polyester sewing thread)	-	830	-
Cl-3.7(Transverse Ends or End Hems)	-	830	-
Cl-3.8(Side Edges)	-	830	-
Cl-3.9(Stitching)	-	830	-
Cl-5(Marking)	-	830	-
Cl-3.1, Table-1(Count of Yarn, Ne- Warp, Ground, Pile Weft)	-	830	-
Cl-3.1, Table-1(Threads per dm, Min- Warp, Ground, Pile Weft)	-	830	-
Cl-3.1, Table-1(Mass, Min g/m2)	-	830	-
Cl-3.1, Table-1(Terry Ratio, Min)	-	830	-
Cl-3.1, Table-2(Count of Yarn, Ne- Warp)	-	830	-
Cl-3.1, Table-2(Count of Yarn, Ne- Weft)	-	830	-
Cl-3.1, Table-2(Threads per dm Min- Ends)	-	830	-
Cl-3.1, Table-2(Threads per dm Min- Picks)	-	830	-
Cl-3.1, Table-2(Mass, Min g/m2)	-	830	-
Cl-3.2.1, Table-3 (i)(Identification of material)	-	830	-
Cl-3.2.1, Table-3 (ii)("Breaking load on 5.0 cm × 20 cm strips a) Warpway")	-	830	-
Cl-3.2.1, Table-3 (ii)("Breaking load on 5.0 cm × 20 cm strips b) Weftway")	-	830	-
Cl-3.2.1, Table-3 (iii)(Scouring loss, percent, Max)	-	830	-
Cl-3.2.1, Table-3 (iv)(Dimensional change, percent, Max)	-	830	-
Cl-3.2.1, Table-3 (v)(pH value)	-	830	-
Cl-3.2.1, Table-3 (vi)(Wettability, Max)	-	830	-
Cl-3.2.1, Table-3 (vii)(Minimum colour fastness rating to: a) Light)	-	830	-
Cl-3.2.1, Table-3 (vii)(Minimum colour fastness rating to: b) Washing)	-	830	-
Cl-3.2.1, Table-3 (vii)(Minimum colour fastness rating to: c) Hypochlorite)	-	830	-
Cl-3.3(Freedom from Defects)	-	830	-
Cl-3.4, 3.5, Table-4(Minimum Dimensions- Width)	-	830	-
Cl-3.4, 3.5, Table-4(Minimum Dimensions- Length)	-	830	-
Cl-3.4, 3.5, Table-4(Maximum Heading)	-	830	-
Cl-3.7(Transverse Ends or End Hems)	-	830	-
Cl-3.8(Side Edges)	-	830	-
Cl-3.9(Stitching)	-	830	-
Cl-5(Marking)	-	830	-
Cl-3.1, Table-1(Count of Yarn, Ne)	-	830	-
Cl-3.1, Table-1(Threads per dm, Min)	-	830	-
Cl-3.1, Table-1(Mass, Min)	-	830	-
Cl-3.1, Table-1(Terry Ratio, Min)	-	830	-
Cl-3.1, Table-2(Count of Yarn, Ne)	-	830	-
Cl-3.1, Table-2(Threads per dm Min)	-	830	-
Cl-3.1, Table-2(Mass, Min)	-	830	-
Cl-3.2.1, Table-3 (i)(Identification of material)	-	830	-
Cl-3.2.1, Table-3 (ii)(Breaking load on 5.0 cm × 20 cm strips Min)	-	830	-
Cl-3.2.1, Table-3 (iii)(Scouring loss, percent, Max)	-	830	-
Cl-3.2.1, Table-3 (iv)(Dimensional change, percent, Max)	-	830	-
Cl-3.2.1, Table-3 (v)(pH value)	-	830	-
Cl-3.2.1, Table-3 (vi)(Wettability, Max)	-	830	-
Cl-3.2.1, Table-3 (vii), a(Minimum Colour Fastness Rating to Light)	-	830	-
Cl-3.2.1, Table-3 (vii), b(Minimum Colour Fastness Rating to Washing)	-	830	-
Cl-3.2.1, Table-3 (vii), c(Minimum Colour Fastness Rating to Hypochlorite)	-	830	-
Cl-3.2.2(Whiteness index)	-	830	-
Cl-3.3(Freedom from Defects)	-	830	-
Cl-3.4, Table-4(Minimum Dimensions-Width)	-	830	-
Cl-3.4, Table-4(Minimum Dimensions-Length)	-	830	-
Cl-3.5, Table-4(Maximum depth of plain heading)	-	830	-
Cl-3.6 (a)(Cotton sewing thread)	-	830	-
Cl-3.6 (b)(Polyester sewing thread)	-	830	-
Cl-3.7(Transverse Ends or End Hems)	-	830	-
Cl-3.8(Side Edges)	-	830	-
Cl-3.9(Stitching)	-	830	-
Cl-5(Marking)	-	830	-
Cl-3.1, Table-1(Count of Yarn, Ne- Warp, Ground, Pile Weft)	-	830	-
Cl-3.1, Table-1(Threads per dm, Min- Warp, Ground, Pile Weft)	-	830	-
Cl-3.1, Table-1(Mass, Min g/m2)	-	830	-
Cl-3.1, Table-1(Terry Ratio, Min)	-	830	-
Cl-3.1, Table-2(Count of Yarn, Ne- Warp)	-	830	-
Cl-3.1, Table-2(Count of Yarn, Ne- Weft)	-	830	-
Cl-3.1, Table-2(Threads per dm Min- Ends)	-	830	-
Cl-3.1, Table-2(Threads per dm Min- Picks)	-	830	-
Cl-3.1, Table-2(Mass, Min g/m2)	-	830	-
Cl-3.2.1, Table-3 (i)(Identification of material)	-	830	-
Cl-3.2.1, Table-3 (ii)("Breaking load on 5.0 cm × 20 cm strips a) Warpway")	-	830	-
Cl-3.2.1, Table-3 (ii)("Breaking load on 5.0 cm × 20 cm strips b) Weftway")	-	830	-
Cl-3.2.1, Table-3 (iii)(Scouring loss, percent, Max)	-	830	-
Cl-3.2.1, Table-3 (iv)(Dimensional change, percent, Max)	-	830	-
Cl-3.2.1, Table-3 (v)(pH value)	-	830	-
Cl-3.2.1, Table-3 (vi)(Wettability, Max)	-	830	-
Cl-3.2.1, Table-3 (vii)(Minimum colour fastness rating to: a) Light)	-	830	-
Cl-3.2.1, Table-3 (vii)(Minimum colour fastness rating to: b) Washing)	-	830	-
Cl-3.2.1, Table-3 (vii)(Minimum colour fastness rating to: c) Hypochlorite)	-	830	-
Cl-3.3(Freedom from Defects)	-	830	-
Cl-3.4, 3.5, Table-4(Minimum Dimensions- Width)	-	830	-
Cl-3.4, 3.5, Table-4(Minimum Dimensions- Length)	-	830	-
Cl-3.4, 3.5, Table-4(Maximum Heading)	-	830	-
Cl-3.7(Transverse Ends or End Hems)	-	830	-
Cl-3.8(Side Edges)	-	830	-
Cl-3.9(Stitching)	-	830	-
Cl-5(Marking)	-	830	-

08 May, 2028

-
Included w.e.f 04.09.2025

1525

VERTEX TESTING LABORATORY PRIVATE LIMITED, GHAZIABAD

8185906

IS 2202 : Part 1 (2023)

WOODEN FLUSH DOOR SHUTTERS SOLID CORE TYPE SPECIFICATION PART 1 PLYWOOD FACE PANELS Seventh Revision

MR,BWP/Decorative, Non Decorative/All Size/8DS20 to 12DT21

17000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.1(Workmanship & Finish)	-	200	-
9.2(Workmanship & Finish)	-	0	-
9.3(Workmanship & Finish)	-	0	-
11.1(Dimensions - Height)	-	200	-
11.1(Dimensions - Width)	-	200	-
11.1(Dimensions - Thickness)	-	200	-
11.1(Dimensions - Variation in thickness)	-	200	-
11.1(Dimensions - Squareness)	-	200	-
11.12(End immersion test)	-	300	-
11.13(Knife Test)	-	300	-
11.14(Glue Adhesion Test)	-	200	-
4(GRADE)	-	100	-
4(TYPE)	-	100	-
5(SIZES)	-	100	-
7.1.1(CONSTRUCTION-Blockboard Core)	-	100	-
7.1.1(CONSTRUCTION-Blockboard Core)	-	0	-
7.1.2(CONSTRUCTION-Blockboard Core)	-	0	-
7.3.2(CONSTRUCTION-Stiles and Rails)	-	100	-
7.3.2(a)(CONSTRUCTION-Stiles and Rails-Joints)	-	0	-
7.3.2(b)(CONSTRUCTION-Stiles and Rails-Joints)	-	0	-
7.3.2(c)(CONSTRUCTION-Stiles and Rails-Joints)	-	0	-
7.3.3(CONSTRUCTION-Stiles and Rails)	-	0	-
9.1(WORKMANSHIP AND FINISH)	-	0	-
9.2(WORKMANSHIP AND FINISH)	-	0	-
9.3(WORKMANSHIP AND FINISH)	-	0	-
11.1(Dimensions and Squareness Test)	-	100	-
11.1(Dimensions and Squareness Test)	-	100	-
11.1(Dimensions and Squareness Test)	-	100	-
11.1(Dimensions and Squareness Test)	-	100	-
11.1(Dimensions and Squareness Test)	-	100	-
11.2(General Flatness Test)	-	100	-
11.2(General Flatness Test)	-	0	-
11.2(General Flatness Test)	-	0	-
11.3(Local Planeness Test)	-	100	-
11.4(Impact Indentation Test)	-	200	-
11.4(Impact Indentation Test)	-	0	-
11.5(Flexure Test)	-	200	-
11.5(Flexure Test)	-	0	-
11.6(Edge Loading Test)	-	300	-
11.6(Edge Loading Test)	-	0	-
11.6(Edge Loading Test)	-	0	-
11.6(Edge Loading Test)	-	0	-
11.7.1(Shock Resistance Test)	-	300	-
11.7.2(Shock Resistance Test)	-	0	-
11.8(Buckling Test)	-	300	-
11.8(Buckling Test)	-	0	-
11.8(Buckling Test)	-	0	-
11.9.2(Slamming Test)	-	300	-
11.9.3(Slamming Test)	-	0	-
11.10(Misuse Test)	-	300	-
11.11(Varying Humidity Test)	-	500	-
11.11(Varying Humidity Test)	-	0	-
11.12(End Immersion Test)	-	300	-
11.13(Knife Test)	-	300	-
11.14(Glue Adhesion Test)	-	500	-
11.15(Screw Withdrawal Resistance Test)	-	800	-
11.15(Screw Withdrawal Resistance Test)	-	0	-
Clause 4.2(grades specified)	-	300	-
Clause 5(SIZES)	-	200	-
Clause 6.1.1(species of timber)	-	200	-
Clause 6.1.2(list of species)	-	200	-
Clause 6.1.3(moisture content)	-	500	-
Clause 6.2.1(Plywood)	-	300	-
Clause 6.2.2(Decorative plywood)	-	500	-
Clause 6.3(Cross-Bands)	-	300	-
Clause 6.4.1(Commercial Face Veneers)	-	300	-
Clause 6.4.2(Decorative Face Veneers)	-	200	-
Clause 6.6.1(Adhesives)	-	500	-
Clause 6.7(Particle Board)	-	500	-
Clause 6.8(Medium density fibre board)	-	500	-
Clause 6.9(Alternative Materials)	-	200	-
Clause 7.1(Blockboard Core)	-	200	-
Clause 7.2(Particle Board or Medium Density Fibre)	-	200	-
Clause 7.3(Stiles and Rails)	-	200	-
Clause 7.4(Levelling)	-	200	-
Clause 7.5(Face Panel)	-	200	-
Clause 7.6(Lipping)	-	200	-
Clause 7.7(Rebating)	-	200	-
Clause 7.8(Opening for Glazing)	-	200	-
Clause 7.9(Venetian)	-	200	-
Clause 8.1(Locks)	-	200	-
Clause 9(WORKMANSHIP AND FINISH)	-	200	-
Clause 10.1(Classification of Tests)	-	200	-
Clause 11.1(Dimensions and Squareness Test)	-	200	-
Clause 11.2(General Flatness Test)	-	200	-
Clause 11.3(Local Planeness Test)	-	200	-
Clause 11.4(Impact Indentation Test)	-	200	-
Clause 11.5(Flexure Test)	-	200	-
Clause 11.6(Edge Loading Test)	-	200	-
Clause 11.7(Shock Resistance Test)	-	200	-
Clause 11.8(Buckling Resistance Test)	-	200	-
Clause 11.9(Slamming Test)	-	200	-
Clause 11.10(Misuse Test)	-	200	-
Clause 11.11(Varying Humidity Test)	-	100	-
Clause 11.12(End Immersion Test)	-	100	-
Clause 11.13(Knife Test)	-	100	-
Clause 11.14(Glue Adhesion Test)	-	100	-
Clause 11.15(Screw Withdrawal Resistance Test)	-	100	-
Clause 12(SAMPLING AND CRITERIA FOR CONFORMITY)	-	100	-
Clause 13(ADDITIONAL REQUIREMENTS FOR ECO MARK)	-	100	-
Clause 14(Marking)	-	100	-
4(Grade, Type and Construction)	-	100	-
5(Sizes and Thickness)	-	100	-
6.1(Timber)	-	100	-
6.2(Plywood for flush door shutter)	-	0	-
6.3(Cross-Bands )	-	0	-
6.4.1(Commercial Face Veneers)	-	0	-
6.4.2(Decorative face veneers)	-	0	-
6.6(Adhesives)	-	0	-
6.7(Particle Board)	-	0	-
6.8(Medium Density Fibre)	-	0	-
6.9(Alternative Materials)	-	0	-
7(Construction)	-	0	-
8.1(Locks)	-	0	-
8.2(Other Fittings)	-	0	-
9(Workmanship and Finish)	-	0	-
10(Tests)	-	0	-
11.1(Dimensions and Squareness Test)	-	0	-
11.2(General Flatness Test)	-	0	-
11.3(Local Planeness Test)	-	0	-
11.4(Impact Indentation Test)	-	0	-
11.5(Flexure Test)	-	0	-
11.6(Edge Loading Test)	-	0	-
11.7(Shock Resistance Test)	-	0	-
11.8(Buckling Resistance Test)	-	0	-
11.9(Slamming Test)	-	0	-
11.1(Misuse Test)	-	0	-
11.11(Varying Humidity Test)	-	0	-
11.12(End Immersion Test)	-	0	-
11.13(Knife Test)	-	0	-
11.14(Glue Adhesion Test)	-	0	-
11.15(Screw Withdrawal Resistance Test)	-	0	-
14(Marking )	-	0	-
Cl-13(ADDITIONAL REQUIREMENTS FOR ECO MARK)	-	0	-

23 May, 2028

-
Included w.e.f. 04.09.2025

1526

Excel Surveyors Pvt. Ltd., Kolkata

5135906

IS 3601 (2006)

Steel tubes for mechanical and general engineering purposes - Specification (Second Revision)

Types-WT;HFS;CDS; CEW (All Grades)

6900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Material)	-	100	-
13(Mechanical Testing)	-	0	-
6.0(Workmanship)	-	100	-
4.1(Sulphur-Percentage by mass)	-	100	-
4.1(Phosphorus-Percentage by mass)	-	100	-
8.0(Straightness)	-	100	-
19.1.1, 24.1.1, 28.1.1, 33.1.1(Dimensions- Outside Dia)	-	200	-
19.1.2, 24.1.2, 28.1.2, 33.1.2(Dimensions- Thickness)	-	100	-
11.1(Surface Protection)	-	300	-
11.2(Surface Protection)	-	0	-
13.1.3(Tensile Strength)	-	500	-
13.1.1(Yield Stress)	-	0	-
13.1.2(Elongation)	-	0	-
13.2(Flattening Test)	-	350	-
13.3(Bend Test (Strip))	-	500	-
13.4(Bend Test (Whole Tube))	-	500	-
13.5(Drift Expansion Test)	-	500	-
13.6(Crush Test)	-	500	-
19.1.3(Height of Internal Fin)	-	200	-
6.0(Workmanship)	-	0	-
4.1(Sulphur-Percentage by mass)	-	0	-
4.1(Phosphorus-Percentage by mass)	-	0	-
8.0(Straightness)	-	0	-
19.1.1, 24.1.1, 28.1.1, 33.1.1(Dimensions- Outside Dia)	-	0	-
19.1.2, 24.1.2, 28.1.2, 33.1.2(Dimensions- Thickness)	-	0	-
11.1(Surface Protection)	-	0	-
11.2(Surface Protection)	-	0	-
13.1.3(Tensile Strength)	-	0	-
13.1.1(Yield Stress)	-	0	-
13.1.2(Elongation)	-	0	-
13.2(Flattening Test)	-	0	-
13.3(Bend Test (Strip))	-	0	-
13.4(Bend Test (Whole Tube))	-	0	-
13.5(Drift Expansion Test)	-	0	-
13.6(Crush Test)	-	0	-
19.1.3(Height of Internal Fin)	-	200	-
Cl. 10 Annex B Cl. 17, Cl. 19(Moment of inertia)	-	200	-
Cl. 10 Annex B Cl. 17, Cl. 19(Radius of gyration)	-	200	-
Cl. 10 Annex B Cl. 17, Cl. 19(Modulus of section)	-	300	-
Cl. 10 Annex B Cl. 17, Cl. 19(Area of cross section)	-	200	-
Cl. 19.1.3(Internal Fin Height)	-	0	-
Cl. 10 Annex B Cl. 17, Cl. 19(Mass)	-	300	-
Cl. 9(Length)	-	150	-
4.0 (a)(Carbon as C - IS:8811)	-	100	-
4.0 (b)(Manganese as Mn - IS:8811)	-	100	-
4.0 (b)(Manganese as Mn - IS:8811)	-	0	-
4.0 (c)(Micro Alloying elements (Nb+V+Ti))	-	100	-
4.0 (f)(Nitrogen content)	-	100	-
9(Length -SOP MT-23)	-	0	-
10(Outside diameter-SOP MT-23)	-	0	-
10(Thickness - SOP MT-23)	-	0	-
10(Mass of Tube-SOP MT-23)	-	0	-
10(Area of Cross Section)	-	200	-
16(Marking)	-	100	-
CL 10("1.Outer dia (04) 2.Thickness (08)")	-	150	-
CL 10(Minimum Outer dia (04))	-	150	-
CL 10(Maximum Outer dia (04))	-	0	-
Cl-10(" Minimum Thickness (08)")	-	150	-
CL 10(Maximum Thickness (08))	-	150	-
4(Material)	-	-	-
13(Mechanical Testing)	-	-	-
Cl. 10 Annex B Cl. 17, Cl. 19(Moment of inertia)	-	-	-
Cl. 10 Annex B Cl. 17, Cl. 19(Radius of gyration)	-	-	-
Cl. 10 Annex B Cl. 17, Cl. 19(Modulus of section)	-	-	-
Cl. 10 Annex B Cl. 17, Cl. 19(Area of cross section)	-	-	-
Cl. 19.1.3(Internal Fin Height)	-	-	-
Cl. 10 Annex B Cl. 17, Cl. 19(Mass)	-	-	-
Cl. 9(Length)	-	-	-
4.0 (a)(Carbon as C - IS:8811)	-	-	-
4.0 (b)(Manganese as Mn - IS:8811)	-	-	-
4.0 (b)(Manganese as Mn - IS:8811)	-	-	-
4.0 (c)(Micro Alloying elements (Nb+V+Ti))	-	-	-
4.0 (f)(Nitrogen content)	-	-	-
9(Length -SOP MT-23)	-	-	-
10(Outside diameter-SOP MT-23)	-	-	-
10(Thickness - SOP MT-23)	-	-	-
10(Mass of Tube-SOP MT-23)	-	-	-
10(Area of Cross Section)	-	-	-
16(Marking)	-	-	-
CL 10("1.Outer dia (04) 2.Thickness (08)")	-	-	-
CL 10(Minimum Outer dia (04))	-	-	-
CL 10(Maximum Outer dia (04))	-	-	-
Cl-10(" Minimum Thickness (08)")	-	-	-
CL 10(Maximum Thickness (08))	-	-	-

31 Dec, 2026

-
Included w.e.f 12.11.2025

1527

ALPHA TEST HOUSE SERVICES LLP (Unit-1), MOHALI

9184906

IS 17954 (2023)

TELESCOPIC BALL BEARING DRAWER SLIDE SPECIFICATION

All

24000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.2, Table- 2 (i)(Internal channel)	-	24000	-
Cl-4.2, Table- 2 (ii)(Outer channel)	-	24000	-
Cl-4.2, Table- 2 (iii)(Track up to 550 mm)	-	24000	-
Cl-4.2, Table- 2 (iv)(Track from 600 mm onwards)	-	24000	-
Cl-4.2, Table- 2 (v)(Ball cage)	-	24000	-
Cl-4.2, Table- 2 (vi)(Ball spacer)	-	24000	-
Cl-5(Components and Manufacture)	-	24000	-
Cl-5(Components and Manufacture)	-	24000	-
Cl-6.1(Preparatory Measures)	-	24000	-
Cl-6.2 (a)(Limiting Deviations- Force)	-	24000	-
Cl-6.2 (b)(Limiting Deviations- Speed)	-	24000	-
Cl-6.2 (c)(Limiting Deviations- Weights)	-	24000	-
Cl-6.2 (d)(Limiting Deviations- Dimension)	-	24000	-
Cl-6.3(Application of Forces)	-	24000	-
Cl-6.4(Testing Equipment)	-	24000	-
Cl-6.5(Sequence of testing)	-	24000	-
Cl-7(Vertical Load Test)	-	24000	-
Cl-8(Horizontal Load Test)	-	24000	-
Cl-9(Durability Test)	-	24000	-
Cl-10(Deflection Test)	-	24000	-
Cl-11(Slam Test)	-	24000	-
Cl-12(Finish)	-	24000	-
Cl-5.11(Ball)	-	24000	-
Cl-5.10(Rivets)	-	24000	-
4.1(size of the telescopic ball bearing slide)	-	24000	-
6.6 (amendment 1)(difference of the maximum forces for opening and closing)	-	24000	-

25 Apr, 2028

-
Included w.e.f.28.08.2025

1528

ALPHA TEST HOUSE PVT LTD, BAHADURGARH

8185306

IS 16208 (2015)

Textiles - High density polyethylene (HDPE)/polypropylene (PP) woven sacks for packaging 10 kg, 15 kg, 20 kg, 25 kg and 30 kg foodgrains - Specification

All

19800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(TYPES)	-	300	-
4.1(Raw Material)	-	300	-
4.2(Tapes – Width IS 6192 and IS 11197)	-	300	-
4.2(Tapes – Linear Density )	-	300	-
4.2(Construction)	-	300	-
4.3(Sacks)	-	300	-
4.3.1(Bottom Seam)	-	300	-
4.3.1( The two rows of stitches shall be separated from each other)	-	300	-
4.3.1( The outer stitch)	-	300	-
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	300	-
4.3.1(Stitches pass through a minimum of six layers of the fabric. )	-	300	-
4.3.1(The number of stitches/dm)	-	300	-
4.3.2(Mouth)	-	300	-
4.4 and Table 1 i(Capacity)	-	300	-
5.2 and Table 1 ii a(Dimensions Inside Length)	-	300	-
5.2 and Table 1 ii b(Dimensions Inside Width)	-	300	-
5.2 and Table 1 iii(Ends per dm )	-	300	-
5.2 and Table 1 iv(Picks per dm )	-	300	-
5.1 and Table 1 v(Mass of sack )	-	300	-
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise )	-	300	-
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise )	-	300	-
5.2 and Table 1 vi(Breaking strength of bottom seam )	-	300	-
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise)	-	300	-
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise )	-	300	-
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	300	-
5.2 and Table 1 x(Ash content )	-	300	-
3(TYPES)	-	300	-
4.1(Raw Material)	-	300	-
4.2(Tapes – Width IS 6192 and IS 11197)	-	300	-
4.2(Tapes – Linear Density )	-	300	-
4.2(Construction)	-	300	-
4.3(Sacks)	-	300	-
4.3.1(Bottom Seam)	-	300	-
4.3.1( The two rows of stitches shall be separated from each other)	-	300	-
4.3.1( The outer stitch)	-	300	-
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	300	-
4.3.1(Stitches pass through a minimum of six layers of the fabric. )	-	300	-
4.3.1(The number of stitches/dm)	-	300	-
4.3.2(Mouth)	-	300	-
4.4 and Table 1 i(Capacity)	-	300	-
5.2 and Table 1 ii a(Dimensions Inside Length)	-	300	-
5.2 and Table 1 ii b(Dimensions Inside Width)	-	300	-
5.2 and Table 1 iii(Ends per dm )	-	300	-
5.2 and Table 1 iv(Picks per dm )	-	300	-
5.1 and Table 1 v(Mass of sack )	-	300	-
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise )	-	300	-
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise )	-	300	-
5.2 and Table 1 vi(Breaking strength of bottom seam )	-	300	-
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise)	-	300	-
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise )	-	300	-
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	300	-
5.2 and Table 1 x(Ash content )	-	300	-
4.2 (Mesh size and weight in g/cm2) (amendment 3)(Mesh size and weight in g/cm2)	-	300	-
3(TYPES)	-	300	-
4.1(Raw Material)	-	300	-
4.2(Tapes – Width IS 6192 and IS 11197)	-	300	-
4.2(Tapes – Linear Density )	-	300	-
4.2(Construction)	-	300	-
4.3(Sacks)	-	300	-
4.3.1(Bottom Seam)	-	300	-
4.3.1( The two rows of stitches shall be separated from each other)	-	300	-
4.3.1( The outer stitch)	-	300	-
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	300	-
4.3.1(Stitches pass through a minimum of six layers of the fabric. )	-	300	-
4.3.1(The number of stitches/dm)	-	300	-
4.3.2(Mouth)	-	300	-
4.4 and Table 1 i(Capacity)	-	300	-
5.2 and Table 1 ii a(Dimensions Inside Length)	-	400	-
5.2 and Table 1 ii b(Dimensions Inside Width)	-	400	-
5.2 and Table 1 iii(Ends per dm )	-	400	-
5.2 and Table 1 iv(Picks per dm )	-	400	-
5.1 and Table 1 v(Mass of sack )	-	400	-
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise )	-	400	-
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise )	-	400	-
5.2 and Table 1 vi(Breaking strength of bottom seam )	-	400	-
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise)	-	400	-
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise )	-	400	-
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	400	-
5.2 and Table 1 x(Ash content )	-	400	-
3(TYPES)	-	400	-
4.1(Raw Material)	-	400	-
4.2(Tapes – Width IS 6192 and IS 11197)	-	400	-
4.2(Tapes – Linear Density )	-	400	-
4.2(Construction)	-	400	-
4.3(Sacks)	-	400	-
4.3.1(Bottom Seam)	-	400	-
4.3.1( The two rows of stitches shall be separated from each other)	-	400	-
4.3.1( The outer stitch)	-	400	-
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	400	-
4.3.1(Stitches pass through a minimum of six layers of the fabric. )	-	400	-
4.3.1(The number of stitches/dm)	-	400	-
4.3.2(Mouth)	-	400	-
4.4 and Table 1 i(Capacity)	-	400	-
5.2 and Table 1 ii a(Dimensions Inside Length)	-	400	-
5.2 and Table 1 ii b(Dimensions Inside Width)	-	400	-
5.2 and Table 1 iii(Ends per dm )	-	400	-
5.2 and Table 1 iv(Picks per dm )	-	400	-
5.1 and Table 1 v(Mass of sack )	-	400	-
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise )	-	400	-
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise )	-	400	-
5.2 and Table 1 vi(Breaking strength of bottom seam )	-	400	-
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise)	-	400	-
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise )	-	400	-
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	400	-
5.2 and Table 1 x(Ash content )	-	400	-
4.2 (Mesh size and weight in g/cm2) (amendment 3)(Mesh size and weight in g/cm2)	-	400	-

08 May, 2028

-
Included w.e.f. 01.09.2025

1529

WELL TECH TEST AND RESEARCH CENTER, DERABASSI

9177306

IS 4329 (1967)

Specification for measuring (Travelling) microscope

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No. 3(Dimension)	-	3000	-
Cl. No. 4(General requirement)	-	3000	-
Cl. No. 5(Functional requirement)	-	3000	-
Cl. No. 6.1(stage)	-	2000	-
Cl. No. 6.2(Magnification)	-	2000	-
Cl. No. 6.3(Numerical aperture)	-	2000	-
Cl. No. 6.4(Resolving Power)	-	2000	-
Cl. No. 6.5(Moment of horizontal cartillage )	-	2000	-
Cl. No. 6.6(Vertical moment)	-	2000	-
Cl. No. 6.7.1(Cross wire)	-	2000	-
Cl. No. 6.8(Fine motion )	-	2000	-
Cl. No. 7(Marking)	-	1000	-
Cl. No. 3(Dimension)	-	0	REPEAT
Cl. No. 4(General requirement)	-	0	REPEAT
Cl. No. 5(Functional requirement)	-	0	REPEAT
Cl. No. 6.1(stage)	-	0	REPEAT
Cl. No. 6.2(Magnification)	-	0	REPEAT
Cl. No. 6.3(Numerical aperture)	-	0	REPEAT
Cl. No. 6.4(Resolving Power)	-	0	REPEAT
Cl. No. 6.5(Moment of horizontal cartillage )	-	0	REPEAT
Cl. No. 6.6(Vertical moment)	-	0	REPEAT
Cl. No. 6.7.1(Cross wire)	-	0	REPEAT
Cl. No. 6.8(Fine motion )	-	0	REPEAT
Cl. No. 7(Marking)	-	0	REPEAT
Cl. No. 3(Dimension)	-	0	REPEAT
Cl. No. 4(General requirement)	-	0	REPEAT
Cl. No. 5(Functional requirement)	-	0	REPEAT
Cl. No. 6.1(stage)	-	0	REPEAT
Cl. No. 6.2(Magnification)	-	0	REPEAT
Cl. No. 6.3(Numerical aperture)	-	0	REPEAT
Cl. No. 6.4(Resolving Power)	-	0	REPEAT
Cl. No. 6.5(Moment of horizontal cartillage )	-	0	REPEAT
Cl. No. 6.6(Vertical moment)	-	0	REPEAT
Cl. No. 6.7.1(Cross wire)	-	0	REPEAT
Cl. No. 6.8(Fine motion )	-	0	REPEAT
Cl. No. 7(Marking)	-	0	REPEAT

30 Mar, 2027

-
Cl. No. 4 (General requirement) THERMAL EXPANSION COEFFICENT EQUIPMENT NOT AVAILABLE

1530

GLOBAL COMPLIANCE LABORATORY INDIA, GHAZIABAD

5172706

IS 302 : Part 2 : Sec 206 (1994)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 206 electric coffee makers

35000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
32(Radiation hazards)	-	3000	-
31(Resistance to Rusting)	-	3000	-
30(Resistance to Heat, Fire and Tracking)	-	3000	-
29(Clearances, Creepage Distances & Solid Insulation)	-	3000	-
28(Screws & Connection)	-	3000	-
27(Provision For Earthing)	-	3000	-
26(Terminals For External Conductors)	-	3000	-
25(Supply Connection & External Flexible Cables and Cords)	-	3000	-
23(Internal wiring)	-	3000	-
22(Construction)	-	3000	-
21(Mechanical strength)	-	3000	-
20(Stability & Mechanical Hazards)	-	3000	-
19(Abnormal Operation)	-	3000	-
18(Endurance)	-	3000	-
17(Overload Protection)	-	3000	-
15(Moisture Resistance)	-	3000	-
14(Radio and television interference suppression/ Transient Overvoltages)	-	3000	-
13(Electrical insulation and Leakage Current at Operating Temperature)	-	3000	-
12(Operation under overload conditions of appliances with heating elements)	-	3000	-
11(Temperature Rise/Heating)	-	3000	-
10(Input)	-	3000	-
8(Protection against Electric Shock/ Protection against Access to Live Parts)	-	3000	-
7(Marking/ Marking & Instructions)	-	3000	-
6(Classification)	-	3000	-
5(Rating)	-	3000	-
16(Insulation resistance and Electric Strength (After humidity treatment))	-	3000	-

20 Jun, 2026

-
Included w.e.f. 29.09.2025 Exclusion: "24 (Component) 9 (Starting Of Motor Operated Appliances) 19.11.4.1 (Electrostatic discharges) 19.11.4.2 (Radiated fields) 19.11.4.3 (Fast transient bursts) 19.11.4.4 (Surge immunity test) 19.11.4.5 (Immunity to conducted discharges) 19.11.4.6 (Class 3 Voltage dips and interruptions) 19.11.4.7 (Harmonics) "

Bureau of Indian Standards

The National Standards Body of India

Search by IS Number