BIS - LIMS (Laboratory Information Management System)

BIS, Southern Regional Laboratory (SRL)

IV CROSS ROAD, CIT CAMPUS, TARAMANI, CHENNAI-600113, TAMILNADU, CHENNAI, Chennai, Tamil Nadu, 600113

- srol@bis.gov.in

Scope List

Reset

246 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

121

IS 733 (1983)

Specification for wrought aluminium and aluminium alloy bars, rods and sections (For General Engineering Purposes) (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 4 (Freedom from Defects)	-
Cl. 5.1, Table 2 (0.2 Percent proof stress- IS 1816)	-
Cl. 5.1, Table 2 (Tensile Strength- IS 1816)	-
Cl. 5.1, Table 2 (Elongation on 50 mm or 5.65√So Gauge Length)	-
Cl. 0.4, 5.1, Table 1 (Aluminium- IS 504 or by any other suitable instrumental method)	-
Cl. 0.4, 5.1, Table 1 (Copper- IS 504 or by any other suitable instrumental method)	-
Cl. 0.4, 5.1, Table 1 (Magnesium- IS 504 or by any other suitable instrumental method)	-
Cl. 0.4, 5.1, Table 1 (Silicon- IS 504 or by any other suitable instrumental method)	-
Cl. 0.4, 5.1, Table 1 (Iron- IS 504 or by any other suitable instrumental method)	-
Cl. 0.4, 5.1, Table 1 (Zinc- IS 504 or by any other suitable instrumental method)	-
Cl. 0.4, 5.1, Table 1 (Aluminium- IS 504 or by any other suitable instrumental method)	-
Cl. 0.4, 5.1, Table 1 (Titanium and / or other grain refining elements - IS 504 or by any other suitable instrumental method)	-
Cl. 0.4, 5.1, Table 1 (Chromium- IS 504 or by any other suitable instrumental method)	-
Cl. 0.4, 5.1, Table 1 (Ti+ V- IS 504 or by any other suitable instrumental method)	-
Cl. 0.4, 5.1, Table 1 (Total Impurities- IS 504 or by any other suitable instrumental method)	-
Cl. 0.4, 5.1, Table 1 (Cr+ Mn- IS 504 or by any other suitable instrumental method)	-
Table-1, Clause - 5.1 (Iron)	-
Table-1, Clause - 5.1 (Manganese)	-

-
" 1 m 5 pieces for chemical testing Excluding Facility for preparation of test specimen not available

122

IS 7452 (1990)

Hot rolled steel sections for doors, windows and ventilators - Specification

Rs 1800/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
cl 6 (Dimensions)	-
cl 7 (MASS AND MASS TOLERANCE)	-
cl 8 (SURFACE FINISH)	-

-
" 1.5 mt + 50g Excluding Excl Bend Test, raw material

123

IS 778 (1984)

Specification for 2010 copper alloy gate, globe and check valves for waterworks purposes (Fourth Revision)

Rs 4500/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3 (Nominal Sizes )	-
4 (Classification )	-
5 (Types)	-
7.1.1 (Body End Ports -IS 778)	-
7.1.2 (Water-Way Area - IS 778)	-
7.1.3 (Screwed Body End -IS 778)	-
7.1.4 (Flanged Body End IS 778)	-
7.1.4.1- Table 3 (Thickness of flange - IS 778)	-
7.1.4.1- Table 3 (Diameter of Belt circle -IS 778)	-
7.1.4.1- Table 3 (No. of holes - IS 778)	-
7.1.4.1- Table 3 (Diameter of holes -IS 778)	-
7.1.4.1 (Holes in flange - IS 778)	-
7.1.5 (Wedge and Disc Guides in the Bodies of Gate Valves - IS 778)	-
7.2.1 (Bonnets - IS 778)	-
7.2.1.1 (Bonnets - IS 778)	-
7.2.1.2 (number of engaged threads - IS 778)	-
7.2.1.2 (pitch of threads - IS 778)	-
7.2.1.3 (Bonnets - IS 778)	-
7.2.2 (Bonnet Flanges - IS 778)	-
7.3 (Stuffing Box - IS 778)	-
7.4 (Gland - IS 778)	-
7.5 (Back Seat- IS 778)	-
7.6.1 (Stem - IS 778)	-
7.6.3 (actuating threads - IS 778)	-
7.6.4 (Length of Stem - IS 778)	-
7.6.5 (Upper end of Stem - IS 778)	-
7.6.6 (Rising Stem - IS 778)	-
7.6.6.1 (Rising Stem - IS 778)	-
7.6.7 (Non-rising Stem - IS 778)	-
7.7.1 (Wedge-IS 778)	-
7.7.2 (Wedge-IS 778)	-
7.7.3 (Double disc - IS 778)	-
7.7.3.1 (Spreading assembly - IS 778)	-
7.7.3.2 (Disc - IS 778)	-
7.8 (Disc Assembly for Globe Valves - IS 778)	-
7.8.1 (One-Piece Disc - IS 778)	-
7.8.2 (Renewable Disc Assembly - IS 778)	-
7.9 (Disc for Check Valves - IS 778)	-
7.9.1 (Disc of glove and Check Valves - IS 778)	-
7.10.1 (Body Seats - IS 778)	-
7.10.1 (Seat ring - IS 778)	-
7.11 (Handwheel - IS 778)	-
8.1- Table 4 (Thickness of Body and Bonnet- IS 778)	-
8.2 - Table 5 (Flat to Flat size -IS 778 )	-
8.3 - Table 6 (Width of end - IS 778)	-
8.4 - Table 7 (Stem Diameters - IS 778)	-
8.5 - Table 8 (Size of packing space - IS 778)	-
8.5 - Table 8 (Dia of stuffing box - IS 778)	-
8.6- Table 9 to Table 12 (End to end/ centre to ends/ Face to face/Centre to face dimension )	-

-
" 1no+raw mat Excluding except thread checking, raw material tests

124

IS 9523 (2000)

Ductile iron fittings for pressure pipes for water, gas and sewage - Specification (First Revision)

Rs.7245.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5 (Thickness)	-
Cl 6 & Table 4,5,6&7 (Design & Tolerance)	-
Cl 9 (Tensile Test & Hardness Test)	-
Cl 11 (Nominal Diameter, Ovality, Dimensions, No. Of Holes & Bolt Sizes)	-
Cl 13 (Coating)	-

-
-

125

IS 1239 : Part 1 (2004)

Steel tubes, tubulars and other wrought steel fittings - Specification: Part 1 steel tubes (Sixth Revision)

Rs. 9200/- Excluding test on joints View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (Outer Diameter, Thickness & Mass)	-
Cl 15 (Workmanship)	-
Cl 14 (Tensile Test, Flattening Test & Bend Test)	-
Cl 14 (Tensile Test, Flattening Test & Bend Test)	-
Cl. 6.1.1, table1 of IS 1239(Part1) (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1.1, table1 of IS 1239(Part1) (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1.1, table1 of IS 1239(Part1) (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1.1, table1 of IS 1239(Part1) (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
7, 6.1.1 (NITROGEN)	-
7, 6.1.1 (SILICON)	-
7, 6.1.1 (ALUMINIUM)	-
6.2 AND AS PER IS 10748 (CARBON EQUIVALENT)	-
6.2 AND AS PER IS 10748 (MICRO ALLOY)	-
6.2 AND AS PER IS 10748 (COPPER)	-
12 AND AS PER IS 4736 (UNIFORMITY OF ZINC COATING)	-
12 AND AS PER IS 4736 (MASS OF ZINC COATING)	-

-
" 3m Chemical Facility is available Quantity: 5 Pieces of 5cm X 5cm Excluding excl bend test, joint (thread checking),hydrostatic test & Leak proof test (at manufacturer’s works). Facility for preparation of test specimen not available.

126

IS 12592 (2002)

Precast concrete manhole cover and frame - Specification (First Revision)

1809 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3 (Grade)	-
3 (Type/Shape of Cover)	-
4.4 (Reinforcement)	-
4.5 (Steel Fibres - Diameter / equivalent diameterofsteel tibres)	-
5.2 and Table 1 (Dimensions of Frame - A)	-
5.2 and Table 1 (Dimensions of Frame - B)	-
5.2 and Table 1 (Dimensions of Frame - C)	-
5.2 and Table 1 (Dimensions of Frame - D)	-
5.2 and Table 1 (Dimensions of Frame - E)	-
5.2 and Table 1 (Dimensions of Frame - F)	-
5.2 (Dimensions of cover- Diameter)	-
5.2 (Clearance at top between the frame and the cover all round the periphery)	-
5.2 (Top surface ofthe frame and cover is in level)	-
5.2 (Suitable taper matching with taper given for the frame shall be provided to the periphery of the cover)	-
5.2 and Fig 1 (Clear cover to reinforcement)	-
5.2 and Fig 1 (Distance of housing from the edge)	-
7.4.1 (Edge Protection and Finishing - Frame)	-
7.4.1 (Edge Protection and Finishing - Frame)	-
7.4.2 (Edge Protection and Finishing - Cover)	-
7.4.2 (Edge Protection and Finishing - Cover)	-
8 (LIFTING HOOKS)	-
9.1 (General)	-

-
1 no each COMPLETE TEST FACILITY AVAILABLE

127

IS 10124 : Part 1 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 1 General Requirements (Second Revision)

Rs 1500/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (Size of fitting)	-
5.1 Table-1 Fig.1 (Dimension of Socket length)	-
5.1.3 (Out of Roundness Tolerance of Socket Inside Diameter)	-
5.2 Table-2 Fig.2 (Dimensions of socket for elastomeric sealing ring)	-
6.1 (Opacity test in accordance with IS 12235 (Part 3))	-
6.2 (Short Term Hydraulic Test in accordance with Annex A)	-
8 (Marking)	-

-
" 6 nos+1no.fitted with pipe Excluding Except Short Term Hydrostatic Test,effect on water

128

IS 4270 (2001)

Steel tubes used for water wells specification (Third Revision)

Rs.7500/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 6 (Tensile Test & Flattening Test)	-
Cl 7 (Outer Diameter, Thickness, Mass & Straightness)	-
Cl 14 (Workmanship)	-
5.2 (phosphorus)	-
5.2 (sulphur)	-

-
" mech - 3 m Chemical Facility is available Quantity: 5 Pieces of 5cm X 5cm Excluding except Hydrostatic test, Pipe tube/ends, Sockets, Alignment test, Protective Coating, Protection of ends

129

IS 8784 (1987)

Specification for thermocouple compensating cables (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (Type of thermocouple)	-
4.1 (Conductor)	-
5 (INSULATION AND SHEATH)	-
6 (ARMOURING)	-
7 (SHIELDING)	-
8.1 (NOISE REDUCTION: Drain Wire)	-
8.2 (NOISE REDUCTION)	-
9.1 (DIMENSION : Single Wire)	-
9.1.1 (DIMENSION : Single Wire (Tolerances))	-
9.1.2 (DIMENSION : Single Wire (Ovality))	-
9.2.1 (Thickness of Insulation )	-
9.2.2 (Thickness of Sheath )	-
9.3 (Dimension of cable )	-
10.1 (Colour Code )	-
11.1 (ENVIRONMENTS FOR USE OF DIFFERENT THERMOCOUPLE COMPENSATING CABLES)	-
12.1 (INFORMATION TO BE SUPPLIED BY THE MANUFACTURER)	-
13.1 (PACKING AND MARKING)	-
13.2 (PACKING AND MARKING)	-
13.2.1 (Standard Mark)	-
14.3 (Resistance Test)	-
14.4.1 ( Thickness of Insulation)	-
14.4.2.1 ( Thickness of Sheath : Round )	-
14.4.2.2 ( Thickness of Sheath : Oval )	-
14.5 (Insulation Resistance Test :Volume resistivity ( Before High Voltage test ))	-
15.5 (Insulation Resistance Test :Insulation resistance constant ( Before High Voltage test ))	-
14.5 (Insulation Resistance Test: Volume resistivity ( After High Voltage test ))	-
15.5 (Insulation Resistance Test: Insulation Resisatnce constant ( After High Voltage test ))	-
14.7 (H.V. Test )	-
14.8 (Heat Shock Test)	-

-
Excluding Except Thermal EMF Test (14.2), Rubber (5.1) and Asbestos (5.3)

130

IS 3589 (2001)

Steel pipes for water and sewage (168.3 To 2540 Mm Outside Diameter) - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
11.1, Table 5. (Outside Diameter (OD))	-
11.1, Table 5. (Thickness)	-
11.1, Table 5. (Mass)	-
14.1 (Visual inspection, Appearance and Workmanship)	-
14.4 (Visual inspection, Appearance and Workmanship-Dent Length)	-
12.3.3 (Ovality)	-
12.5 (Strightness)	-
8.1 Table 2 Table 3 (Carbon Content IS 228)	-
8.1 Table 2 Table 3 (Manganese Content IS 228)	-
8.1 Table 2 Table 3 (Phosphorus Content IS 228)	-
8.1 Table 2 Table 3 (Sulphur Content IS 228)	-

-
" 2 mt Chemical Facility is available Quantity: 5 Pieces of 5cm X 5cm excluding Hydraulic Pressure Test, Guided Bend Test. Prepared test piece needed for Tensile test Facility

131

IS 3575 (1993)

Bitumen drums - Specification (Third Revision)

1800.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Dimensions Drums (Figure 1))	-
4.1 (Dimensions Closure (Figure 2))	-
5.1 (Body and ends)	-
5.2 (Closures)	-
6.1 (Construction)	-
7.1 (Finish)	-
7.2 (Finish)	-
6.2 (Construction)	-
6.3 (Construction)	-
6.4 (Construction)	-
8 (Air Pressure Test)	-
4.1 (Dimensions Drums (Figure 1))	-

-
-

132

IS 3502 (2009)

Steel chequered plates (Third Revision)

2985 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5 (Workmanship)	-
Cl 8 (Tensile Test)	-
Cl 9 (Press)	-
Cl 10 (Length, Width, Thickness & Chequered Height)	-
Cl 10 (Length, Width, Thickness & Chequered Height)	-
Cl 9 (Press)	-

-
" 1.5 sq m Excluding except Chemical tests

133

IS 1783 : Part 2 (2014)

Drums large, fixed ends - Specification: Part 2 grade B drums (Fourth Revision)

5550 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (Capacity)	-
5 (Dimensions (Type 1 C Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 C Drums Figure 2))	-
5 (Dimensions (Type 1 C Drums Figure 2))	-
5 (Dimensions (Type 1 C Drums Figure 2))	-
5 (Dimensions (Type 1 C Drums Figure 2))	-
5 (Dimensions (Type 1 C Drums Figure 2))	-
5 (Dimensions (Type 1 C Drums Figure 2))	-
5 (Dimensions (Type 1 D Drums Figure 2))	-
6 (Material)	-
7 (Construction)	-
7.1 (Construction)	-
7.2 (Construction)	-
7.3 (Construction)	-
7.4 (Construction)	-
7.5 (Construction)	-
7.7 (Construction)	-
8 (Finish )	-
9.1 (Leakage at air pressure )	-
9.2 (Drop Test)	-
9.3 (Hydraulic Pressure Test)	-

-
-

134

IS 3319 (1995)

Blades, surgical, detachable (Bard Parker Type) and handles - Specification (Fourth Revision)

Please check remarks View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8,8.1 (Sterilization)	-
8.2 (Sterilization)	-
5,5.1 & 5.2; Table 1 (Shape and dimensions)	-
6,6.1 (Workmanship and Finish)	-
6,6.2 (Workmanship and Finish)	-
6,6.3 (Workmanship and Finish)	-
6,6.4 (Workmanship and Finish)	-
7.1 (Hardness test)	-
9.1 ( Visual Examination)	-
9.2 ( Performance Test)	-
10.1.1 ( Marking on Blade)	-
10.1.2 (Packages of Non-sterile Blades)	-
10.1.3,10.1.3.1 (Packages of sterile Blades,Unit containers for sterile Blades)	-
10.1.3,10.1.3.2 (Packages of sterile Blades , Outer containers for sterile blade)	-
10.2 ( Handles)	-
10.2.2 ( Packages of Handles)	-

-
" Mech - 50 nos./ Micro - 30nos. except Chemical tests and Hardness

135

IS 432 : Part 2 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 2 Hard-Drawn Steel Wire

Rs 3900/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 4.1 (Workmanship)	-
Cl 5 & 6 (Diameter)	-
Cl 7 (UTM)	-
Cl 4.1 (Workmanship)	-
Cl 5 & 6 (Diameter)	-
Cl 7 (UTM)	-

-
1m Excluding TF for chemical tests not available.Tensile test Facility available till 20mm only

136

IS 432 : Part 1 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 1 Mild Steel and Medium Tensile Steel Bars

Rs 2100/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5.1 (Workmanship)	-
Cl 6.2 (Diameter & Ovality)	-
Cl 6.2 (Weight)	-
Cl 8.2 (Bend test)	-
Cl 6.1 (Diameter)	-

-
" 1m + 25g Excluding except chemical tests up to 20mm

137

IS 4947 (2006)

Foam concentrate for producing mechanical foam for fire fighting - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 3 (General Requirements)	-
Cl 8 (Finish)	-

-
" 2 no. " Excluding hydraulic & burst pressure tests and chem tests

138

IS 4948 (2020.0)

Welded steel wire fabric for general use - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 5.1 (MANUFACTURE OF MESH (Assembling of Wires))	-
Cl. 5.2 (MANUFACTURE OF MESH)	-
Cl. 5.3 (MANUFACTURE OF MESH)	-
Cl. 5.4 (Spacing of Longitudinal and Transverse Wires)	-
Cl. 5.5 (Tolerance of Size of Mesh)	-
Cl. 5.6 (Tolerance of Size of Sheet or Roll)	-
Cl. 9.1 (Marking)	-
Cl. 9.3 (BIS Certification Marking)	-
Cl. 10.1 (Finish)	-

-
1mt Excluding excl shear strength test & chemical tests

139

IS 2879 (1998)

Mild steel for metal arc welding electrodes - Specification (Third Revision)

Testing charges are Rs.9050/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 7 (Workmanship)	-
Cl 8 & 9 (Diameter)	-

-
" 1 mt + 50 gm Excluding excluding chemical tests

140

IS 280 (2006)

Mild steel wire for general engineering purposes (Fourth Revision)

Rs.3750.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 9 (Tensile Test On UTM)	-
Cl 13 (Workmanship)	-
Cl 7 & Table 1 (Diameter & Difference Between Two Reading On Any Two Diameters)	-
6 AND AS PER IS 7887 (MICRO ALLOY)	-
6 AND AS PER IS 7887 (ALUMINIUM)	-
6 AND AS PER IS 7887 (PHOSPHORUS)	-
6 AND AS PER IS 7887 (SULPHUR)	-
6 AND AS PER IS 7887 (MANGANESE)	-
6 AND AS PER IS 7887 (SILICON)	-
6 AND AS PER IS 7887 (CARBON)	-
Clause 6 and Note 3 of IS 7887 (Copper)	-

-
" 3 m+ 50gm " Chemical Facility is available Quantity: 5 Pieces of 5cm X 5cm Excluding Mech-C /

141

IS 5489 (1975)

Specification for carburizing steels for use in bearing industry (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7 ( HARDNESS)	-
11.3 (i) Tolerance on Length -IS : 3739-1972)	-
11.4 (ii)Tolerance on Straightness)	-
12 ( SIZE AND WEIGHT OF WIRE AND WIRE ROD)	-

-
" 2 x 1 m " Excluding except inclusion content, Grain size and Chemical tests

142

IS 2681 (1993)

Non - Ferrous metal sliding door bolts (Aldrops) for use with padlocks - Specification (Third Revision)

1500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 8.1 (Brass sliding door bolts shall have satin finish or shall be polished or plated as specified by the purchaser)	-
Cl. 8.2 (Ref. Cl.9 of IS 1868:1996) (Anodinc casting thickness (Cl. 9.2 of IS 1868:1996))	-
4 (SIZES)	-
6.1-Total 2 (DIMENSIONS AND TOLERANCES-A)	-
6.1-Total 2 (DIMENSIONS AND TOLERANCES-B)	-
6.1-Total 2 (DIMENSIONS AND TOLERANCES-C)	-
6.1-Total 2 (DIMENSIONS AND TOLERANCES-D)	-
6.1-Total 2 (DIMENSIONS AND TOLERANCES-E)	-
6.1-Total 2 (DIMENSIONS AND TOLERANCES-F)	-
6.1-Total 2 (DIMENSIONS AND TOLERANCES-G)	-
6.1-Total 2 (DIMENSIONS AND TOLERANCES-H)	-
6.1-Total 2 (DIMENSIONS AND TOLERANCES-L)	-
6.1-Total 2 (DIMENSIONS AND TOLERANCES-M)	-
6.1-Table 3 (DIMENSIONS AND TOLERANCES-R)	-
6.1-Table 3 (DIMENSIONS AND TOLERANCES-T)	-
6.1-Table 3 (DIMENSIONS AND TOLERANCES-U)	-
7.1 (MANUFACTURE-General)	-
7.1 (MANUFACTURE-General)	-
8.1 (FINISH)	-
3 (TYPES)	-
6.1-Total 2 (DIMENSIONS AND TOLERANCES-J)	-
6.1-Total 2 (DIMENSIONS AND TOLERANCES-K)	-
6.1-Total 2 (DIMENSIONS AND TOLERANCES-N)	-
6.1-Total 2 (DIMENSIONS AND TOLERANCES-Q)	-
6.1-Total 2 (DIMENSIONS AND TOLERANCES-S)	-
6.1-Total 2 (DIMENSIONS AND TOLERANCES-W)	-
6.1-Total 2 (DIMENSIONS AND TOLERANCES-No. of Screw on Staple or Clip to accommodate Wood Screw N0 8)	-
6.1-Table 3 (DIMENSIONS AND TOLERANCES-A)	-
6.1-Table 3 (DIMENSIONS AND TOLERANCES-B)	-
6.1-Table 3 (DIMENSIONS AND TOLERANCES-C)	-
6.1-Table 3 (DIMENSIONS AND TOLERANCES-D)	-
6.1-Table 3 (DIMENSIONS AND TOLERANCES-E)	-
6.1-Table 3 (DIMENSIONS AND TOLERANCES-F)	-
6.1-Table 3 (DIMENSIONS AND TOLERANCES-H)	-
6.1-Table 3 (DIMENSIONS AND TOLERANCES-J)	-
6.1-Table 3 (DIMENSIONS AND TOLERANCES-K)	-
6.1-Table 3 (DIMENSIONS AND TOLERANCES-L)	-
6.1-Table 3 (DIMENSIONS AND TOLERANCES-M)	-
6.1-Table 3 (DIMENSIONS AND TOLERANCES-Pin dia)	-
6.1-Table 3 (DIMENSIONS AND TOLERANCES-R)	-
6.1-Table 3 (DIMENSIONS AND TOLERANCES-T)	-
6.1-Table 3 (DIMENSIONS AND TOLERANCES-U)	-
6.1-Table 3 (DIMENSIONS AND TOLERANCES-No. of Screw on Staple or Clip to accommodate Wood Screw N0 8)	-
7.1 (MANUFACTURE-General)	-
7.2 (MANUFACTURE-Brass Sliding Door Bolts or Aluminium Alloy Sliding Door Bolts)	-
7.2 (MANUFACTURE-Brass Sliding Door Bolts or Aluminium Alloy Sliding Door Bolts)	-
8.2 (FINISH)	-
8.2 (FINISH-anodic casting -Min Avg thickness)	-
8.2 (FINISH-anodic casting -Min Local thickness)	-

-
" 3+2 Nos. Excluding except chemical tests and anodic coating

143

IS 2385 (1977)

Specification for hot - Rolled mild steel sheet and strip in coil form for cold - Reduced tinplate and cold - Reduced blackplate (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 (Freedom from defects)	-
8 (Dimensions and Tolerances)	-

-
" Mech- 2 x 500 mm Excluding except Chemical tests

144

IS 7098 : Part 1 (1988)

Specification for crosslinked polyethylene insulated pvc sheathed cables: Part 1 for working voltages up to and including 1100 volts (First Revision)

26250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3 (CONDUCTOR: MATERIALS)	-
4 (INSULATION : MATERIALS)	-
5.1 (FILLER AND INNER SHEATH)	-
5.2 (FILLER AND INNER SHEATH)	-
6 (ARMOURING)	-
7 (OUTER SHEATH)	-
8.1 (CONDUCTOR: CONSTRUCTION)	-
8.2 (PROTECTIVE BARRIER)	-
8.3 (SIZE OF NEUTRAL CONDUCTOR)	-
9.1 (Insulation Applied by extrusicn)	-
9.2 (Thickness of Insulation - Average)	-
9.3 (Thickness of Insulation - Minimum)	-
9.4 (Application of Insulation)	-
10.1 (Core Identification)	-
10.2 (Core Identification- Neutral)	-
10.3 (Core Identification by number )	-
10.4 (Core Identification by number - Neutral )	-
11 (LAVING UP OF CORES)	-
12.1 & 12.2 (Inner sheath : Application)	-
12.3 (Thickness of Inner Sheath)	-
13.1 (Armouring: Application)	-
13.1.2 (Armouring: Coverage )	-
13.1.3 (Armouring: Direction of Lay )	-
13.2 (Type of armour )	-
13.3 (Armouring : Dimensions -Wire Diameter)	-
13.3 (Armouring : Dimensions -Formed wire )	-
13.4 (Armour: Joint)	-
13.5 (Armouring : Resistance Test)	-
13.6 a) (ARMOURING: Tensile Strength)	-
13.6 b) (ARMOURING: Elongation )	-
13.6 c) (ARMOURING: Torsion Test (For round wire ) )	-
13.6 d) (ARMOURING: Winding Test(For formed wire))	-
13.6 e) (ARMOURING: Uniformity of zinc coating)	-
13.6 f) (ARMOURING: Mass of zinc coating )	-
13.6 g) (ARMOURING: Resistivity)	-
14.1 (Outer Sheath : Application)	-
14.2 (Colour of outer sheath)	-
14.3 (Thickness of outer sheath - AVERAGE)	-
14.3 (Thickness of outer sheath - minimum)	-
15.1 a) i) (Annealing Test ( For copper wire ) )	-
15.1 a) ii) (Tensile test (for aluminium) - Before stranding )	-
15.1 a) ii) (Tensile test (for aluminium) - After stranding )	-
15.1 a) iii) (Wrapping test (for aluminium))	-
15.1 a) iv) (Resistance test - Main conductor)	-
15.1 a) iv) (Resistance test - Neutral conductor)	-
15.1 d) i) (Phyaical tests for insulation : Tensile Test)	-
15.1 d) i) (Phyaical tests for insulation : Elongation)	-
15.1 d) ii) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-
15.1 d) ii) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-
15.1 d) iii) (Phyaical tests for insulation : Hot set )	-
15.1 d) iii) (Phyaical tests for insulation : Permanent set )	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage )	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage - Crack observed )	-
15.1 d) v) (Insulation: Waterabsorption(gravimetric))	-
15.1 e) i) (Physical tests for outer sheath : Tensile stregth)	-
15.1 e) i) (Physical tests for outer sheath : Elongation)	-
15.1 e) i) (Physical tests for outer sheath : Tensile stregth)	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation )	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-
15.1 e) iii) (Sheath: Loss of mass in air oven)	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage )	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-
15.1 e) v) (Sheath : Hot deformation)	-
15.1 e) vi) (Sheath : Heat shock test)	-
15.1 e) vii) (Sheath : Thermalstability)	-
15.1 f) (INSULATION RESISTANCE TEST : Volume resistivity )	-
16.2 (HIGH VOLTAGE TEST )	-
16.3 (FLAMMABILITY TEST : Period of Burning )	-
16.3 (FLAMMABILITY TEST : Unaffected length )	-
17.1 (Manufacturer'. identification)	-
17.2 (cable Indentification )	-
17.3 (cable Code )	-

-
15m Excluding Except C1 & C2 Category, Cu Purity Test

145

IS 2255 (1977)

Specification for mild steel wire rod for the manufacture of machine screws (By Cold Heading Process) (Second Revision)

Rs. 600/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7 (Sizes and tolernces)	-
8 (FREEDOM FROM DEFECTS)	-

-
" 3 m Excluding except chemical tests

146

IS 210 (2009)

Grey iron castings - Specification (First Revision)

Rs.2700.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1 (WORKMANSHIP AND FINISH)	-
10.1 (FREEDOM FROM DEFECTS)	-
13 (SIZE OF TEST BARS-Diameter)	-
13 (SIZE OF TEST BARS-Length)	-
15, Table 3 (TENSIL.E TEST- IS 1608 Part1 )	-
16, Table 3 (Hardness Test)	-
18 (HYDROSTATIC TEST)	-
17,Annex B (TRANSVERSE TEST)	-

-
" 3 TEST BARS Excluding Hardness test

147

IS 2090 (1983)

Specification for high tensile steel bars used in prestressed concrete (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5 (Tolerances (Size & Mass))	-
6.1, Table 1 (i) 0.2% Proof stress, Mpa)	-
6.1, Table 1 (ii)Ultimate Tensile Strength, Mpa)	-
6.1, Table 1 (iii)Elongation, %)	-

-
" mech - 4 m Excluding except Chemical tests

148

IS 1673 (1984)

Spectfication for mild steel wire, cold heading quality (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 (FREEDOM FROM DEFECTS)	-
8 ( DIMENSIONS AND TOLERANCES)	-

-
" mech - 3 m " Excluding except reverse torsion test, crushing test, tensile properties and chemical tests

149

IS 1783 : Part 1 (2014)

Drums large, fixed ends - Specification: Part 1 grade A drums (Fourth Revision)

Rs.4800/- and testing charges as per relevant referred View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (Capacity)	-
5 (Dimensions (Type 1 C Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 C Drums Figure 2))	-
5 (Dimensions (Type 1 C Drums Figure 2))	-
5 (Dimensions (Type 1 C Drums Figure 2))	-
5 (Dimensions (Type 1 C Drums Figure 2))	-
5 (Dimensions (Type 1 D Drums Figure 2))	-
7.1 (Construction)	-
7.2 (Construction)	-
7.3 (Construction)	-
7.4 (Construction)	-
7.5 (Construction)	-
7.6 (Construction)	-
8 (Finish )	-
9.1 (Leakage at air pressure )	-
9.2 (Drop Test)	-
9.3 (Hydraulic Pressure Test)	-

-
-

150

IS 1566 (1982)

Specification for hard - Drawn steel wire fabric for concrete reinforcement (Second Revision)

Rs 300/- + mat test as per IS:432(Pt 2) View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 (DIMENSIONS)	-
8 (MASS)	-
10 (MECHANICAL PROPERTIES)	-
11.2 (Tensile Test)	-
9.4 (Tolerance on Mass of Fabric)	-
7 (SIZES OF SHEETS ‘OR ROLLS)	-
9.2 (Tolerance on Size of Mesh)	-
9.3 (Tolerance on Size of Sheet)	-
10 (MECHANICAL PROPERTIES)	-

-
" 2 x 500 mm Excluding except bend test and chemical tests

First
Prev
4
5
6
7
Next
Last

Bureau of Indian Standards

The National Standards Body of India

BIS, Southern Regional Laboratory (SRL)

IV CROSS ROAD, CIT CAMPUS, TARAMANI, CHENNAI-600113, TAMILNADU, CHENNAI, Chennai, Tamil Nadu, 600113

- srol@bis.gov.in

Scope List