BIS - LIMS (Laboratory Information Management System)

BIS, Central Laboratory (CL)

20/9, Site 4, Sahibabad Industrial Area, Sahibabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201010

- sample@bis.gov.in

Scope List

Reset

892 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

361

IS 6803 (1972)

Specification for special proofed canvas and duck

11297 View breakup
Rs. 11297/- + testing charges as per referred ISS (excluding Pressure head test).

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 3.2.3 (pH Value)	-
Cl. 3.2.1 , Appendix A-1 (Proofing Content)	-

-
-

362

IS 9271 (2004)

Unplasticized polyvinyl chloride (UPVC) single wall corrugated pipes for drainage - Specification (First Revision)

1800/ View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8.2 (Density-When tested in accordance with ]S 13360 (Part 3/Sec 1), the densi of the pipe shall be between 1.40 and 1.46 gm/cm3 .)	-
8.1.1 (Visual Appearance, Workmanship and Finish)	-
8.1.2 (Visual Appearance, Workmanship and Finish)	-
7.2, 8 (Wall Thickness)	-
7, Table 1 (DIMENSIONS AND TOLERANCE-The nominal outside diameter and tolerances of the corrugated pipes shall be as per Table 1)	-
7.4.3 (Perforation Requirement-The heght of corrugation -The depth of corrugations shall be 3 percent, Min of nominal outside diameter (dn).)	-

-
Excluding Test Fcility not available for Cl 8.3 Pipe stiffness, Cl 8.4 Impact strength at o Degree C, Cl 8.5 Elongation Test, Cl 8.6 Bending Test, Cl 8.7 Joints (optional)

363

IS 14106 (2018)

Direct action hand pumps - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 (Visual tests: All the pumps shall be examined for workmanship, finish and visual defects.)	-
6.2.2 (i) Aligment of groove in top guide bush with respect to the nuts welded on pump body)	-
6.2.2 (ii) Aligment of handle nut with pipe for concentricity)	-
6.2.2 (iii) Location of holes in the pump head flange with respect to the direction of the spout)	-
6.2.2 (iv) Reasonable flatness of the flanges to provide proper matching of the holes to ensure unrestricted insertion of the bolts )	-
6.2.2 (v) Matching of faces indicated in respective figures of piston plate, follower plate and foot valve body)	-
6.2.2 (vi) Concentricity of the two internal diameter of the reducing socket)	-
6.3.1 (Routine test)	-
6.4 (Test for Joints)	-
6.4 (Pump Rod)	-
6.4 (Riser Pipe)	-
6.4 (Upper casing and lower casing)	-
6.4 (Load test )	-
4.4 & Table 2 (Bell Dimensions, mm)	-
4.4 & Table 2 (Bell Dimensions for Upper casing pipe)	-
4.4 & Table 2 (a)Socket Depth)	-
4.4 & Table 2 (b) Mean socket internal dia at mouth)	-
4.4 & Table 2 (c) Mean socket internal diameter at root )	-
4.4 & Table 2 (Bell Dimensions for Lower casing pipe)	-
4.4 & Table 2 (a)Socket Depth)	-
4.4 & Table 2 (b) Mean socket internal dia at mouth)	-
4.4 & Table 2 (c) Mean socket internal diameter at root )	-
4.4 & Table 2 (Bell Dimensions for Sand Trap)	-
4.4 & Table 2 (a)Socket Depth)	-
4.4 & Table 2 (b) Mean socket internal dia at mouth)	-
4.4 & Table 2 (c) Mean socket internal diameter at root )	-
6.2.3 (Dimensional tests, Pump head, mm)	-
6.2.3 (Pump head flange)	-
6.2.3 (Pump stand)	-
6.2.3 (Intermediate flange)	-
6.2.3 (Grommet)	-
6.2.3 (Shore Hardness on Scale A)	-
6.2.3 (Top Guide Bush)	-
6.2.3 (Handle)	-
6.2.3 (Handle Cushion Top)	-
6.2.3 (Shore Hardness on Scale A)	-
6.2.3 (Bottom Cushion)	-
6.2.3 (Shore Hardness on Scale A)	-
6.2.3 (Handle Retainer)	-
6.2.3 (Top Connector)	-
6.2.3 (Male Adapter)	-
6.2.3 (Female Adapter)	-
6.2.3 (Piston Plate)	-
6.2.3 (Follower Plate)	-
6.2.3 (Piston Fap Valve)	-
6.2.3 (Shore Hardness on Scale A)	-
6.2.3 (Cup Seal)	-
6.2.3 (Shore Hardness on Scale A)	-
6.2.3 (Bottom Connector)	-
6.2.3 (Grapple Parts)	-
6.2.3 (Foot Valve Body)	-
6.2.3 (O Ring)	-
6.2.3 (Shore Hardness on Scale A)	-
6.2.3 (Flap Valve)	-
6.2.3 (Shore Hardness on Scale A)	-
6.2.3 (Foot valve Guide)	-
6.2.3 (Threaded Coupler(M))	-
6.2.3 (Threaded Coupler(F))	-
6.2.3 (Riser Pipe Centralizer)	-
6.2.3 ( Shore Hardness on Scale A)	-
6.2.3 (O Ring)	-
6.2.3 (Foot Valve Retainer)	-
6.2.3 (Rubber Seat)	-
6.2.3 (Shore Hardness on Scale A)	-
6.2.3 (Reducing Sdocket (Alternate Design))	-
6.2.3 (Well Screen (alternate))	-
6.2.3 (Screen Coupler)	-
6.2.3 (Sand Trap)	-
6.2.3 (Cutter)	-
6.2.3 (Retrieving Rod)	-
6.2.3 (Combination Spanner)	-
5.2(a) (Mass of Zinc coating,g/m2)	-
5.2(a) (Adhesion of coating)	-
5.2(a) (Galvanizing of Head)	-
5.2(b) (Galvanizing of Handle)	-
5.2(b) (Mass of Zinc coating,g/m2)	-
5.2(b) (Adhesion of coating)	-
5.2© (Galvanizing of Stand)	-
5.2© (Mass of Zinc coating,g/m2)	-
5.2© (Adhesion of coating)	-
5.2(d) (Galvanizing of Intermediate Flange)	-
5.2(d) (Mass of Zinc coating,g/m2)	-
5.2(d) (Adhesion of coating)	-
4.2 (Mean Outside Diameter)	-
4.2 (Wall Thickness)	-
4.2 (Length)	-
4.2 (Visual Appearance)	-
4.2 (Test for Internal Diameter)	-
4.2 (Specific Gravity)	-

-
-

364

IS 702 (1988)

Specification for indusrial bitumen (Second Revision)

- View breakup
Hence complete testing charges for the product are Rs.6300..00

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 and 6.1 Table 1 (Specific Gravity, 85/25)	-
5.1 and 6.1 Table 1 (Specific Gravity, 85/40)	-
5.1 and 6.1 Table 1 (Specific Gravity, 90/15)	-
5.1 and 6.1 Table 1 (Specific Gravity, 115/15)	-
5.1 and 6.1 Table 1 (Specific Gravity 135/10)	-
5.1 and 6.1 Table 1 (Specific Gravity 155/6)	-

-
-

365

IS 7283 (1992)

Hot - Rolled bars for the production of bright bars and machined parts for engineering applications specification (First Revision)

Rs 1500/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 6 (Workmanship)	-
Cl 7 (Diameter & Out Of Round)	-
Cl 5 (Material Test)	-

-
Since the composition of steel is mutually agreed basis , as such element to be tested with specified requirement and tolerances if any may please be declared with method of testing. Sample Size 5 pcs of 5x5 cm having dia> 3mm and thickness > 0.8 mm. Excluding i] cl 8 decarburization, ii] cl 11 grain size

366

IS 16088 (2012)

Chlorinated polyvinyl chloride (CPVC) pipes for automatic sprinkler fire extinguishing system - Specification

5400 View breakup
Rs. 5400/- (excluding Compound chlorine content, Fire exposure test, Flammability test, Resistance to external blows at 0oC, Kinking resistance test and CPVS fire sprinkler pipes and fittings) + testing charges as per referred ISS

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
9.5 IS 12235(Part 2) (Vicat Softening Temperature: When tested by the method prescribed in IS 12235(Part 2), the Vicat softening temperature of the specimen shall not be less than 110°C.)	-
9.3 (Reversion test : )	-
9.5 (Density)	-
8 (Pipe Ends)	-
7.1.1 IS 12235 (Part 1) Table 1 (Mean outside Diameter)	-
7.1.1.1 IS 12235 (Part 1) Table 1 (Outside Diameter at any point)	-
7.1.2 (Wall Thickness)	-
10.3 (Flattening)	-
10.4 (Tensile Strength)	-
9.1 (Visual Appearance)	-
5 (Classification of pipes)	-

-
Excluding Testing Facility not avaialble for Cl.9.6 Fire exposure test, cl. 9.7 Flammability Test, cl.10.1 hydrostatic Characterstics, Cl 10.2 resistance to external Blow At 0 °C, Cl. 10.3 flattening Test, Cl.10.5 Kinking Resistance Test, Cl. 10.7 Vibration Test (Type Test)

367

IS 14268 (2022)

Uncoated stress relieved low relaxation seven-wire (ply) strand for prestressed concrete -Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1.2 (Carbon)	-
4.1.2 (Silicon)	-
4.1.2 (Manganese)	-
4.1.2 (Sulphur)	-
4.1.2 (Phosphorus)	-
4.1.2 (Chromium)	-
4.1.2 (Nickel)	-
4.1.2 (Molybdenum)	-
4.1.2 (Copper)	-
4.1.2 (Aluminum)	-
4.1.2 (Sulphur + Phosphorus)	-
4.1.2 (Boron)	-
4.1.2 (Titanium)	-
4.1.2 (Niobium)	-
4.1.2 (Vanadium)	-
4.1.2 (Titanium+Niobium+Vanadium)	-
4.1.2 (Nitrogen)	-
4.5 (Workmanship and Finish)	-
6(Table 2) (Diameter)	-
6(Table 2) (Tensile Strength)	-
6(Table 2) (Cross Sectional Area)	-
6(Table 2) (Mass Per Meter)	-
4.5 (Workmanship and Finish)	-

-
Excluding i] cl 6.2.2 breaking strength & 0.2 % Proof stress, ii] cl 6.2.3 elongation, iii] cl 6.2.4 relaxation properties

368

IS 916 (2000)

Square tins for solid products - Specification (Fourth Revision)

4950 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Capacity)	-
4.2 (Dimension and Tolerances)	-
4.3.1 (Nominal Thickness)	-
4.3.2 (Handle wire diameter)	-
4.3.2 (Handle wire material)	-
4.4.1 (Body)	-
4.4.2 (Sides)	-
4.4.3 (Top and Bottom)	-
4.4.4 (Top and Bottom embossing)	-
4.4.5 (Handle)	-
4.4.6 (Closure)	-
4.4.7 (Supply condition)	-
4.4.8 (Internal Finish)	-
4.4.9 (External Treatment)	-
5.1 (Air-Pressure Test)	-
5.2 (Handle Pull Test)	-

-
Excluding 5.1 Air-Pressure Test, 5.2 Handle Pull Test,

369

IS 9282 (2002)

Wire ropes and strands for suspension bridges - Specification (First Revision)

Rs. 3000/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2.1 ( MATERIAL- Requirements of Wire -Dimensional Limits and Tolerances )	-
4.2.2 (Tensile Test)	-
4.3 (Elongation Test )	-
4.5.1 (Galvanizing)	-
4.5.2 (Wrap Tes)	-
5 (GENERAL REQUIREMENTS General requirements shall be according to IS 6594.)	-
6.1 (JOINTS)	-
7.1 ( DIRECTION OF LAY)	-
8.1 (LENGTH OF LAY)	-
10. table 1 to 11 (MINIMUM BREAKING FORCE )	-
Clasuse - 4 ( CARBON)	-
Clasuse - 4 (SULPHUR)	-
Clasuse - 4 (PHOSPHURS)	-
Clasuse - 4 (MANGANESE)	-
Clasuse - 4 (SILICON)	-
Clasuse - 4 ( ALUMINIUM)	-
Clasuse - 4 (NITROGEN)	-
Clasuse - 4 (Nickel)	-
Clasuse - 4 (Chromium)	-
Clasuse - 4 (Molybdenum)	-
Clasuse - 4 (NIOBIUM)	-
Clasuse - 4 (VANADIUM)	-
Clasuse - 4 (TITANIUM)	-

-
EXCLUDING -; i] cl 10 minimum breaking force, ii] cl 11 elongation or stretch

370

IS 4109 (1967)

Specification for kadahies

Rs. 750/- and testing charges as per referred Iss View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2 (Materials)	-
3 (a) Round Shape / Bowl Shape)	-
3 (b) Nominal dia. at top D1 mm)	-
3 (c) Nominal overall Height H1 mm)	-
3 (d) Thickness at bottom mm Min)	-
4 (Manufacture and Workmanship)	-
6 (Test)	-

-
-

371

IS 285 (1992)

Laundry soaps - Specification (Third Revision)

5300 View breakup
For Type 1 -Rs.6000/-, For Type 2 Gr.1- Rs.4800/-, For Type 2 Gr.2-Rs.5100/- Average testing charges (all types and grades)-Rs.5300.00

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.4, Table-1 (ix) Type-2 (Built soap) Gr-2 (LSD/NSD content, IS 4955)	-
5.4, Table-1 (viii) Type-2 (Built soap) Gr-1 & Gr-2 (Chloride (as sodium chloride), IS 286)	-
5.4, Table-1 (viii) Type-1 (Pure soap) (Chloride (as sodium chloride), IS 286)	-
5.4, Table-1 (vii) Type-1 (Pure soap) (Glycerol, IS 286)	-
5.4, Table-1 (v) Type-2 (Built soap) Gr-1 (Matter insoluble in alcohol, IS 286)	-
5.4, Table-1 (v) Type-1 (Pure soap) (Matter insoluble in alcohol, IS 286)	-
5.4, Table-1 (iv) (Free caustic alkali, as sodium hydroxide (NaOH), IS 286)	-
5.4, Table-1 (iii) (Unsaponified fatty matter, IS 286)	-
5.4, Table-1 (ii) (Rosin acids, percent by mass of total fatty matter, IS 286 )	-
5.4, Table-1 (i) Type-2 (Built soap) Gr-2 (Total fatty matter, IS 286)	-
5.4, Table-1 (i) Type-2 (Built soap) Gr-1 (Total fatty matter, IS 286)	-
5.4, Table-1 (i) Type-1 (Pure soap) (Total fatty matter, IS 286)	-
5.3 (Odour and Lathering Properties, IS 286)	-
5.4, Table-1 (ix) Type-2 (Built soap) Gr-2 (LSD/NSD content, IS 4955)	-
5.4, Table-1 (viii) Type-2 (Built soap) Gr-1 & Gr-2 (Chloride (as sodium chloride), IS 286)	-
5.4, Table-1 (viii) Type-1 (Pure soap) (Chloride (as sodium chloride), IS 286)	-
5.4, Table-1 (v) Type-2 (Built soap) Gr-1 (Matter insoluble in alcohol, IS 286)	-
5.4, Table-1 (v) Type-1 (Pure soap) (Matter insoluble in alcohol, IS 286)	-
5.4, Table-1 (iv) (Free caustic alkali, as sodium hydroxide (NaOH), IS 286)	-
5.4, Table-1 (iii) (Unsaponified fatty matter, IS 286)	-
5.4, Table-1 (ii) (Rosin acids, percent by mass of total fatty matter, IS 286 )	-
5.4, Table-1 (i) Type-2 (Built soap) Gr-2 (Total fatty matter, IS 286)	-
5.4, Table-1 (i) Type-2 (Built soap) Gr-1 (Total fatty matter, IS 286)	-
5.4, Table-1 (i) Type-1 (Pure soap) (Total fatty matter, IS 286)	-
5.3 (Odour and Lathering Properties, IS 286)	-

-
-

372

IS 9165 : Part 2 (1992)

Surgical instruments - Needles, suture: Part 2 eyed needles - Sizes, shapes and dimensions

Rs.10030/ View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1, Table 1 (Dimensions of Eyed Suture Needles)	-
3.1, Table 1 (Dimensions of Eyed Suture Needles)	-

-
-

373

IS 12650 (2018)

Textiles – Jute bags for packing 50 kg foodgrains – Specification (third revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4-4.2 (Manufacture-The number of stitches per decimeter shall be 10 ±1.)	-
4-4.3 (Manufacture-Safety Stitch-The number of safety union stitches per decimetre shall be10 ± 1.)	-
4-4.1 (MANUFACTURE- The bags shall be made from single piece of twill weave jute sacking of uniform construction having nominal mass of 579 g/m2 as given below with warp running along the length of the bag:)	-
4-4.2 (Manufacture-The number of stitches per decimeter shall be 10 ±1.)	-
4-4.3 (Manufacture-Safety Stitch-The number of safety union stitches per decimetre shall be10 ± 1.)	-
4-4.1 (MANUFACTURE- The bags shall be made from single piece of twill weave jute sacking of uniform construction having nominal mass of 579 g/m2 as given below with warp running along the length of the bag:)	-
4-4.1-a) (MANUFACTURE)	-
4-4.1-b) (MANUFACTURE)	-
4-4.1 (MANUFACTURE)	-
4-4.2 (Manufacture)	-
4-4.3 (Manufacture-Safety Stitch )	-
4-4.4 (Manufacture-Hemming at the Mouth )	-
4-4.5 (Manufacture- Freedom from Defects )	-
5-5.1-Table 1-Sr. no. i) (SPECIFIC REQUIREMENTS-Dimensions (see Note 1) Cl. 8.3.2 of IS 9113 a) Out side Length , cm 94 (For both type A & Type B) Tolerance + 4 / -0 cm)	-
5-5.1-Table 1-Sr. no. i) (SPECIFIC REQUIREMENTS-Dimensions (see Note 1) Cl. 8.3.2 of IS 9113 b) Outside width, cm 57 (For both type A & Type B) Tolerance + 4 / -0 cm)	-
5-5.1-Table 1-Sr. no.i i) (SPECIFIC REQUIREMENTS-Cl. 8.4.2 of IS 9113 Ends/dm Type A 46 + 2 /Type B 76 + 4 / -3)	-
5-5.1-Table 1-Sr. no.iii) (SPECIFIC REQUIREMENTS-Cl. 8.4.2 of IS 9113 Picks/dm Type A 50 (2 x 25) / Type B 28 + 2)	-
5-5.1-Table 1-Sr. no.iv) (SPECIFIC REQUIREMENTS-Cl. 8.5.2 of IS 9113 Corrected Mass/bag, g ( See Note 2) For both Type A & Type B 665 + 8.0 / -6.0 percent)	-
5-5.1-Table 1-Sr. No.v) (SPECIFIC REQUIREMENTS-Cl. 8.6.2 of IS 9113 Average breaking strength of sacking (ravelled-strip method, 10 cm × 20 cm), Min, N (kgf): a ) Warpway- 1570 (160) for both type A & Type B)	-
5-5.1-Table 1-Sr. No.v) (SPECIFIC REQUIREMENTS-Cl. 8.6.2 of IS 9113 Average breaking strength of sacking (ravelled-strip method, 10 cm × 20 cm), Min, N (kgf): b ) Weftway- 1420 (145) for both type A & Type B)	-
5-5.1-Table 1-Sr. No.vi) (SPECIFIC REQUIREMENTS-Cl. 8.7 of IS 9113 Average side seam strength (5 cm ×20 cm raveled strip), Min, N (kgf): 490 (50) for both type A & Type B)	-

-
-

374

IS 12594 (1988)

Hot - Dip zinc coating on structural steel bars for concrete reinforcement - Specification

2200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 , Table 1 (Mass of Zinc coating , IS 6745)	-
5.2 (Freedom from defects , IS 2629)	-
5.3 (Adhesion of Galvanized coating)	-
Clause - 4, 4.1 (CARBON)	-
Clause - 4, 4.1 (SULPHUR)	-
Clause - 4, 4.1 (PHOSPHURS)	-
Clause - 4, 4.1 (MANGANESE)	-
Clause - 4, 4.1 (SILICON)	-
Clause - 4, 4.1 (ALUMINIUM)	-
Clause - 4, 4.1 (NITROGEN)	-

-
EXCLUDING -; i] cl 5.4 chromating

375

IS 8074 (1990)

Monocrotophossl - Specification (Second Revision)

Rs.2750.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2 (Physical)	-
3.2.1 (Description)	-
3.2.2 (Cold Test)	-
3.2.3 (Flash Point ( Abel ))	-
3.3 (Chemical)	-
3.3.1 (Monocrotophos Content)	-
3.3.1.1 (actual value of the monocrotophos content)	-
3.3.1.2 (average monocrotophos content)	-
3.3.2 (Free Aceto-Acetic Acid Monomethyl-amide ( MMA ) Content)	-
3.3.3 (Acidit)	-

-
-

376

IS 2414 (2005)

Cycle and rickshaw pneumatic tyres - Specification (Fourth Revision)

Rs.8630/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Type)	-
4.2 (Designation)	-
5.1 & 5.2 (Dimensions)	-
6.1 (Construction)	-
6.2 (Tyre Cord)	-
6.3 (Tyre Casing Strength)	-
6.4 (Bead Wire Joint)	-
6.5 (Requirements of Ruber Compound)	-
6.6 (Adhesion test)	-

-
EXCLUDING -; Performance test

377

IS 3903 (1984)

Specification for dimethoate emulsifiable concentrates

Rs. 3300.00/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.3.2 (Acidity)	-
2.3.1 (Dimethoate Content, NV upto 9)	-
2.3.1 (Dimethoate Content, NV above 50)	-
2.2.3 (Flash Point)	-
2.1 (Constituents)	-
2.2.1 (Description)	-
2.2.2 (Cold Test)	-
2.2.4 (emulsion Stability)	-
2.2.5 (Heat Stability)	-
2.2.4 (emulsion Stability)	-
2.2.5 (Heat Stability)	-
2.3.1 (Dimethoate Content, NV above 9 and below 50)	-

-
EXCLUDING Cl. 2.3.1 Dimethoate Content;

378

IS 6956 (2001)

Cover paper - Specification (First Revision)

4650 View breakup
"1. for cover paper which are white in colour : 16x300 = Rs.4800.00, 2. for cover paper which are not white in colour : 15x300 = Rs.4500.00 3. test charges for special requirements (for ECO mark) : 6x300 = Rs.1800.00"

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (REQUIREMENTS-General)	-
4.3 (Grarnmage-As per 6 of IS 1060 (Part 1)-Further a mean of 10 test results shall not vary from nominal grarnmage by more than ±4 percent.)	-
4.3 (Grarnmage-As per 6 of IS 1060 (Part 1)- no single test result shall vary by more than *6 percent from nominal)	-
4.2,Table1 (One minute Cobb test (Test method Column 4 and 5 of table1))	-
4.2,Table1 (Smoothness (Bendtsen)-(Test method Column 4 and 5 of table1))	-
4.2,Table1 (Burst Index-(Test method Column 4 and 5 of table1))	-
4.2,Table1 (Ph(Test method Column 4 and 5 of table1))	-
4.2,Table1 (Folding endurance-MD-(Test method Column 4 and 5 of table1))	-
4.2,Table1 (Wax pick-(Test method Column 4 and 5 of table1))	-
4.2,Table1 (Folding endurance-CD-(Test method Column 4 and 5 of table1))	-
4.2,Table1 (Brightness(For white paper only) -(Test method Column 4 and 5 of table1))	-
4.2,Table1 (Opacity, (Test method Column 4 and 5 of table1))	-
4.2,Table1 (Bending stiffness index,-CD-(Test method Column 4 and 5 of table1))	-
4.2,Table1 (Bending stiffness index,-MD-(Test method Column 4 and 5 of table1))	-

-
Test facility is not available for mentioned exclusiosn parameters; EXCLUDING Brightness, Bending stiffness;

379

IS 2566 (1993)

Textiles – B-twill jute bags for packing foodgrains – Specification (third revision)

4800 View breakup
Rs 4800/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.5.2 & Table 2. IS 2969 ( The bales containing the bags shall conform to the requirements as laid down in Table 2. vi) Oil content on dry deoiled material basis, percent, Max)	-

-
-

380

IS 5604 (1984)

Specification for hand - Operated universal gearless pulling and lifting machines (First Revision)

- View breakup
Testing charges = 10.5 x 300 + 2 x 9 = Rs. 3168.00 + testing charges as per referred ISS (excluding Back slippage) (only Visual tests as per Cl. 5).

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (Capacity)	-
5.3 (Construction and Workmanship Casing)	-
5.4 (Construction and Workmanship Bearings)	-
5.4.1 (Ball and Roller Bearings)	-
5.4.2 (Plain Bearings)	-
5.5 (Wire Ropes)	-
5.6 (Heat Treatment)	-
5.7 (Construction and Workmanship Bearings)	-
5.8 (Weight)	-
7.1 (Operation)	-
7.2 (Operation)	-
7.3 (Operation)	-
7.4 (Operation Back Slippage)	-
8 (Effort)	-
9.1 (Proof Loading)	-
9.2 (Operational Test)	-
9.3 (Break Load Testing )	-
9.4 (Examination)	-
11.1 (Marking)	-
Clause -3, 3.1 (Steel bars, Plates and sections)	-
Clause -3, 3.1 (Steel Forgings)	-
Clause -3, 3.1 (Aluminium Alloy)	-
Clause -3, 3.1 (Coil Springs)	-
Clause -3, 3.1 (Hooks)	-
Clause -3, 3.1 (Wire Ropes)	-

-
EXCLUDING -; i] cl 7.4 back slippage, ii] cl 9.2 operational test

381

IS 1943 (1995)

Textiles – A-twill jute bags (second revision)

Rs4100/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1,5.1,Table 1 (Moisture Regain, Percent-IS 9113)	-
4.1,5.1,Table 1 (Oil content, Percent-IS 2969)	-

-
-

382

IS 3992 (1982)

Specification for trays, kidney (First Revision)

Rs.1275/- and material testing charges as per relevant View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1&3.2 (C - IS 228)	-
3.1&3.2 (S - IS 228)	-
3.1&3.2 (P - IS 228)	-
3.1&3.2 (Mn - IS 228)	-
3.1&3.2 (Si - IS 228)	-
3.1&3.2 (Cr - IS 228)	-
3.1&3.2 (Ni - IS 228)	-
4.1 (Shape)	-
4.2, Table-1,1 (Length -A - IS 3992)	-
4.2, Table-1,2 (Width -B - IS 3992)	-
4.2, Table-1,3 (Height -C - IS 3992)	-
4.2, Table-1,7 (Minimum Thickness of material)	-
5.0 &5.1 (Workmanship and finish of stainless steel Trays)	-
5.0 & 5.2 (Workmanship and finish of Enamelled Iron Trays)	-

-
-

383

IS 2932 (2013)

Enamel, synthetic, exterior: (a) Undercoating (b) Finishing - Specification (Fourth Revision)

- View breakup
For Undercoat including Keeping Properties = Rs. (7800+2050+600) = Rs. 10,450 For Finishing including Keeping Properties = Rs. (8475+2050+750) = Rs. 11275 Keeping Properties Only, For Undercoat = Rs. 375/- Keeping Properties Only, For Finishing = Rs. 375/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.3 (Freedom from Coarse Particles)	-
6.4 (Skin Formation)	-
6.5 (Thinning Properties)	-
6.6 (Application Properties)	-
6.8 (Lead Restriction)	-
6.9 Table 2 (1) a. Consistency ( Undercoating and Finishing ) )	-
6.9 Table 2 (1) b. Viscosity by ford 80-120 s )	-
6.9 Table 2 ( 2) Mass, ( Under coating ) )	-
6.9 Table 2 ( 2) Mass, (Finishing ) )	-
6.9 Table 2 (3) Drying time, a) Surface dry, ( Under coating ) )	-
6.9 Table 2 (3) Drying time, a) Surface dry, ( Finishing ) )	-
6.9 Table 2 (b) Hard dry ( Under coating ) )	-
6.9 Table 2 (b) Hard dry, (Finishing ) )	-
6.9 Table 2 (c) Tack free ( Under coating (Finishing ) )	-
6.9 Table 2 (4) a) Finish (Under coating ) )	-
6.9 Table 2 (4) a) Finish (Finishing) )	-
6.9 Table 2 (b) ) Gloss 60º (Under coating ) )	-
6.9 Table 2 (b) ) Gloss 60º (Finishing) )	-
6.9 Table 2 (5) Fineness of grind,(Under coating ))	-
6.9 Table 2 (4) a) Finish (Finishing) )	-
6.9 Table 2 (6) Colour , (Finishing))	-
6.9 Table 2 (7) Flexibility and adhesion: a) Scratch hardness No such scratch as to show the bare metal after Clause 3 of — (Load 1 000 g) ( Under coating & Finishing ) )	-
6.9 Table 2 (b) Bend test (with 6.25 mm 48 h of air in type 1 apparatus) ( Under coating & Finishing ) )	-
6.9 Table 2 (8) Flash point ( Under coating & Finishing ) )	-
6.9 Table 2 (9) Composition:b) Phthalic anhydride content of non-volatile vehicle ( Under coating & Finishing ))	-
6.9 Table 2 (11) Resistance to alkali ( Under coating & Finishing ))	-
6.9 Table 2 (12) Accelerated storage stability test ( Under coating & Finishing ))	-
6.9 Table 2 (13) Keeping properties ( Under coating & Finishing ))	-
6.9 Table 2 (14) Wet opacity ( Under coating & Finishing ))	-

-
Weatherometer for durability, approved sample for resistance to acid and alkali, test facility for volume solids test is required; EXCLUDING Durability, Volume solids, Resistance to acid and alkali;

384

IS 10350 (2020)

Powder Hair Dyes — Specification ( Third Revision )

3,840 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.6 Table 2 () Calculated active matter (as PPD) in the solution after recommended dilution with water/diluent, type 1)	-
4.5 Table 1 (Arsenic (as As2 O3 ), for all types)	-
4.6 Table 2 () Calculated active matter (as PPD) in the solution after recommended dilution with water/diluent, type 1)	-
4.6 Table 2 () Calculated active matter (as PPD) in the solution after recommended dilution with water/diluent, type 1)	-
4.5 Table 2 (pH, Type 3)	-
4.5 Table 1 (pH, type 1 and 2)	-
4.5 Table 1 (Active matter as PPD content, Type 1)	-
4.1 (description)	-
4.6 Table 2 () Calculated active matter (as PPD) in the solution after recommended dilution with water/diluent, type 1)	-
4.5 Table 1 (Arsenic (as As2 O3 ), for all types)	-
4.6 Table 2 () Calculated active matter (as PPD) in the solution after recommended dilution with water/diluent, type 1)	-
4.5 Table 1 (pH, type 1 and 2)	-
4.5 Table 1 (Heavy metals (as Pb), for all types)	-
4.5 Table 1 (Active matter as PPD content, Type 1)	-
4.1 (description)	-
4.5 Table 1 (Dye ingredients, type 3 only)	-

-
-

385

IS 4003 : Part 2 (1986)

Specification for pipe wrenches: Part 2 heavy duty (First Revision)

Rs. 3900/- and testing charges as per referred Iss View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 AND AS PER IS 1570 PART 2 (CARBON)	-
4 AND AS PER IS 1570 PART 2 (SULPHUR)	-
4 AND AS PER IS 1570 PART 2 (PHOSPHORUS)	-
4 AND AS PER IS 1570 PART 2 (MANGANESE)	-
4 AND AS PER IS 4454 PART 1 (CARBON)	-
4 AND AS PER IS 4454 PART 1 (SULPHUR)	-
4 AND AS PER IS 4454 PART 1 (PHOSPHORUS)	-
4 AND AS PER IS 4454 PART 1 (MANGANESE)	-
4 AND AS PER IS 4454 PART 1 (SILICON)	-
4 AND AS PER IS 4454 PART 1 (COPPER)	-
4 AND AS PER IS 4454 PART 1 (NITROGEN)	-
4 AND AS PER IS 4454 PART 1 (cu + cr + ni)	-
4 AND AS PER IS 4454 PART 1 (SULPHUR+ PHOSPHORUS)	-
4 AND AS PER IS 4454 PART 1 (MICRO ALLOY)	-
4 AND AS PER IS 2707 (CARBON)	-
4 AND AS PER IS 2707 (SULPHUR)	-
4 AND AS PER IS 2707 (PHOSPHORUS)	-
4 AND AS PER IS 2707 (MANGANESE)	-
4 AND AS PER IS 2707 (SILICON)	-
4 AND AS PER IS 2707 (MICRO ALLOY)	-
3 (Dimensions- Nominal Size)	-
3 (Dimensions-Capacity D min)	-
3 (Dimensions- Capacity D max)	-
3 (Dimensions- Jaw Thickness,T min)	-
3 (Dimensions- Length of movablejae, l1)	-
3 (Dimensions- Length of Handle, l2)	-
3 (Dimensions- Width of Nut, N)	-
5 (Hardness- Movable and heel Jaws)	-
5 (Hardness- Shank of movable Jaw)	-
5 (Hardness- Adjustable nut)	-
6.1 (Manufacture- Handel)	-
6.1 (Manufacture- Handel)	-
6.2 (Movable Jaw)	-
6.2 (Movable Jaw)	-
6.3 (Heel jaw)	-
6.3 (Heel jaw)	-
6.4 (Adjusting Nut)	-
6.4 (Adjusting Nut)	-
6.4 (Adjusting Nut)	-
6.5 (Springs)	-
6.5 (Springs)	-
7 (Workmanship & Finish)	-
7 (Workmanship & Finish)	-
8 (Operation)	-
11.1 (Static Load Test)	-
11.1 (Static Load Test)	-

-
Suitable grade of Material as per relevant IS may please be declared. Sample Size 5 pcs of 5x5 cm having dia> 3mm and thickness > 0.8 mm;

386

IS 9532 (1980)

Specification for chakka and shrikhand

Rs. 3300.00 (For CHAKKA) & Rs. 4200.00 (For SHRIKHAND) View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2.1 and 3.2.6 Table 2 ( Titratable acidity)	-
3.1.1 and 3.1.6 Table 1 ( Titratable acidity)	-
3.1.1 and 3.1.6 Table 1 (Total ash, Chakka )	-
3.1.1 and 3.1.6 Table 1 (Coliform count)	-
3.2.1 and 3.2.6 Table 2 (Coliform count)	-
3.1.1 and 3.1.6 Table 1 (Yeast and mould count)	-
3.2.1 and 3.2.6 Table 2 (Yeast and mould count)	-

-
500 gm x 3 -As per revised IS 9532 : 2023;

387

IS 14314 (1995)

Thtnner,general purpose,for synthetic paints and varnishes - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 5.1, Clause 4.2, Table 1 (Sr.No. viii) (Keeping Quality (Hydrocarbon content))	-
Clause 5.1, Clause 4.2, Table 1 (Sr.No. vii) (Keeping Quality (Residue on evaporation))	-
Clause 5.1, Clause 4.2, Table 1 (Sr.No. vi) (Keeping Quality (Flash point (Abel)))	-
Clause 5.1, Clause 4.2, Table 1 (Sr.No. v) (Keeping Quality (Distillation range))	-
Clause 5.1, Clause 4.2, Table 1 (Sr.No. iv) (Keeping Quality (Relative density at 27 °C))	-
Clause 5.1, Clause 4.2, Table 1 (Sr.No. iii) (Keeping Quality (Spot test))	-
Clause 5.1, Clause 4.2, Table 1 (Sr.No. ii) (Keeping Quality (Odour))	-
Clause 5.1, Clause 4.2, Table 1 (Sr.No. i) (Keeping Quality (Colour))	-
Clause 4.2, Table 1 (Sr.No. viii) (Hydrocarbon content)	-
Clause 4.2, Table 1 (Sr.No. vii) (Residue on evaporation)	-
Clause 4.2, Table 1 (Sr.No. vi) (Flash point (Abel))	-
Clause 4.2, Table 1 (Sr.No. v) (Distillation range)	-
Clause 4.2, Table 1 (Sr.No. iv) (Relative density at 27 °C)	-
Clause 4.2, Table 1 (Sr.No. iii) (Spot test)	-
Clause 4.2, Table 1 (Sr.No. ii) (Odour)	-
Clause 4.2, Table 1 (Sr.No. i) (Colour)	-

-
Karl fischer apparatus is required; EXCLUDING Water content;

388

IS 1374 (2007)

Poultry feeds - Specification

9500 View breakup
Rs. 9500/- (For all in Table-1; Ca, Total P & available P in Table-2; Mn, I, Fe, Zn, Cu & Se in Table-3)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. No. 4.1 (Description)	-
Cl. No. 4.1.2,table1,i (Moisture,% by mass,Max.)	-
Cl. No. 4.1.2,table1,ii (Crude Protein (N×6.25),(on dry basis) % by mass,Min.)	-
Cl. No. 4.1.2,table1,iv (Crude fibre(on dry basis),% by mass,Max.)	-

-
-

389

IS 14597 (1998)

Synthetic tarpaulins(Heavy Duty Protective Covers) made from coated nylon or polyester fabrics specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5 & Table 1 (Total mass per unit area)	-
Cl 5 & Table 1 (Breaking strength: Longitudinal Direction)	-
(Cl 4.5) (Coating)	-
Cl 6, (Cl. 6.2) (Construction: Fixing of Eyelets)	-
Cl 6, (Cl. 6.1) (Construction: Materials)	-
CL. 5.6 (Shear strength of joint )	-
CL. 5.5 (Resistance to cold)	-
CL. 5.2 (Accelerated ageing)	-
CL. 5.1 ( Workmanship)	-
(Cl 5 & Table 1) (Requirements )	-
5.3 (Water Proofness Test)	-
5.4 (Resistance to damage by Flexing)	-
5.9 Table 2 (Colour fastness to light)	-
5.9 Table 2 (Colour fastness to rubbing)	-
5.10.1 (Flame Resistance Test)	-
5.10.2 (Fusion)	-

-
EXCLUDING 5.3 Water Proofness Test, 5.4 Resistance to Damage by Flexing, 5.6 Shear Strength of Joints/Seams, Table 1, Tear strength, Breaking strength, Heat ageing, mass loss of coating,percent,;

390

IS 6901 (2018)

Gas welding equipment - Pressure regulators and pressure regulators with flow - Metering devices for gas cylinders used in welding, cutting and allied processes up to 300 bar (30 MPA) (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (Materials)	-

-
-

Bureau of Indian Standards

The National Standards Body of India

BIS, Central Laboratory (CL)

20/9, Site 4, Sahibabad Industrial Area, Sahibabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201010

- sample@bis.gov.in

Scope List