BIS - LIMS (Laboratory Information Management System)

BIS, Central Laboratory (CL)

20/9, Site 4, Sahibabad Industrial Area, Sahibabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201010

- sample@bis.gov.in

Scope List

Reset

897 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

331

IS 2415 (2015)

Cycle - Rubber tubes (Moulded/ Jointed) - Specification (Fourth Revision)

Rs 14270/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1, Table 1 (Classification and Designation)	-
5.1,3.4, Annex A & Table 2. ( Flat Length )	-
5.1,3.5, Annex A & Table 2. (Flat Width)	-
5.2, Annex A (Thickness)	-
5.2.1 (Uniformity of Thickness)	-
6.1,Table 3 (i)Tensile strength:)	-
6.1,Table 3 (ii)Elongation at break )	-
6.2 (iii)Tension set: )	-
6.3 (a) ( Ageing Test:- Tensile strength :)	-
6.3(b) ( Ageing Test :- Elongation at break)	-
6.4.1 (Joint Adhesion Strength)	-
6.4.3 ( Strength of splice on moulded tube)	-
6.5 (Leak Test)	-
6.6 (Valve Test)	-
6.7.1 (Manufacture and Workmanship)	-
6.7.2 (Manufacture and Workmanship)	-
6.7.3 (Manufacture and Workmanship)	-
6.7.4 (Manufacture and Workmanship)	-
7.1 (MARKING)	-

-
Excluding Valve test

332

IS 5382 (2018)

Rubber seals - Joint rings for water supply, drainage and sewerage pipelines - Specification for materials (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2.1 (Dimensional tolerances)	-
4.2.2 (Imperfections and defects)	-
4.2.2 (Surface imperfections)	-
4.2.2 (i)In zones involved in sealing function)	-
4.2.2 (ii) In zones not involved in sealing function)	-
4.2.2 (Internal Imperfections)	-
4.2.3 (Hardness, IRHD from buttons )	-
4.2.4 (Tensile strength, MPa)	-
4.2.5 (Compression set in air)	-
4.2.5.2 (Compression set at 23 ºC for 72 h)	-
4.2.5.2 (Compression set at 70 ºC for 24 h)	-
4.2.5.3 (Low temp compression set at -10 ºC for 72 h)	-
4.2.6 (Ageing 7 days at 70 ºC)	-
4.2.6 (Hardness, IRHD from buttons Tensile strength, % Elongation at break , % )	-
4.2.8 (Volume change in water , max/min 7 days at 70 ºC )	-
4.2.10 (Spliced joint)	-

-
Excluding Stress relaxation in compression, Ozone resistance test, Low Temperature Performance at - 25 Degree C (Optional Test)

333

IS 5487 (1992)

Metal polish, liquid - Specification (First Revision)

Rs.4800.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.8, Table-1 (vi) (Oleic acid content, IS 5487 )	-
4.8, Table-1 (v) (Flash point (Abel), IS 1448 Part-20)	-
4.8, Table-1 (iv) (Cyanides, IS 5487)	-
4.8, Table-1 (iii) (Residue on 75miron IS Sieve, IS 5487)	-
4.8, Table-1 (ii) (Total ammonia (as NH3), IS 5487)	-
4.8, Table-1 (i) (Total solids (excluding oils and fatty matter), IS 5487)	-
4.7 (Keeping Quality, IS 5487)	-
4.6 (Acidity of the Aqueous Extract, IS 5487)	-
4.5 (Polishing Property, IS 5487)	-
4.4 (Stability, IS 5487)	-
4.3 (Consistency, IS 5487 )	-
4.8, Table-1 (v) (Flash point (Abel), IS 1448 Part-20)	-
Clause No. 4.1 (Composition)	-
Clause No.4.2 (Odour)	-
Clause No.4.3 (Consistency)	-
Clause No.4.4 (Stability)	-
Clause No.4.5 (Polishing Property)	-
Clause No.4.6 (Acidity of the Aqueous Extract)	-
Clause No. 4.8, Table No. 1, SI. No.1 (Total solids ( excluding oils and fatty matter ))	-
Clause No. 4.8, Table No. 1, SI. No.2 (Total ammonia ( as NH3))	-
Clause No. 4.8, Table No. 1, SI. No.3 (Residue on 75miron IS Sieve)	-
4.8, Table-1 (iv) (Cyanides, IS 5487)	-
4.8, Table-1 (v) (Flash point (Abel), IS 1448 Part-20)	-
4.8, Table-1 (vi) (Oleic acid content, IS 5487 )	-

-
Excluding Cyanides

334

IS 878 (2008)

Laboratory glassware - Graduated measuring cylinders (Second Revision)

Rs.4200/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Table-1 (Nominal capacity)	-
Table-1 (Overall height)	-
Table-1 (Distance from top of scale to top of cylinder)	-
Table-1 (Internal height to highest graduation line)	-
Table-1 (Sub-divisions)	-
Table-1 (capacity at lowest graduation line)	-

-
Complete for chemical Excluding Cl. 11 Accuracy Test and Cl. 7 Maximum permissible error

335

IS 1237 (2012)

Cement Concrete Flooring Tiles - Specification

Rs 4500/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 12.2 (Concavity & Convexity )	-
Cl 12.3 (The Maximum gap between the arms of the square and the edge of the title shall notexceed 2 percent of the length.)	-
Cl 12.4 (Shall not exceed 1 percent of the length of the edge.)	-
Cl 12.5 (Water absorption)	-
Cl 11 (Suface Finish)	-
Cl 7.1 (Length, Breadth, Minimum thickness, Difference in length of side between the longest side and shorterst side, Half tiles, Difference in Thickness between the thickest and thinnest tile, Thickness of wearing layer)	-
Cl 7.1 (Length, Breadth, Minimum thickness, Difference in length of side between the longest side and shorterst side, Half tiles, Difference in Thickness between the thickest and thinnest tile, Thickness of wearing layer)	-
Cl 12.6 (Wet transverse strength )	-

-
Excluding Resistance of wear

336

IS 8471 (2003)

Acetylene generators - Requirements (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1 (MATERIAL AND PROTECTIVE COATING)	-
7.2 (MATERIAL AND PROTECTIVE COATING)	-
Cl. 7.1 (Carbon)	-
Cl. 7.1 (Silicon)	-
Cl. 7.1 (Manganese)	-
Cl. 7.1 (Phosphorous)	-
Cl. 7.1 (Sulphur)	-
Cl. 7.1 (Vanadium)	-
Cl. 7.1 (Niobium)	-
Cl. 7.1 (Titanium)	-
Cl. 7.1 (Aluminium)	-
Cl. 7.1 (Nitrogen)	-
Cl. 7.1 (Nickel)	-
Cl. 7.1 (Chromium)	-
Cl. 7.1 (Molybdenum)	-
Cl. 7.1 (Copper)	-
Cl. 7.1 (V+Nb+Ti)	-
Cl. 7.1 (CE)	-
Cl. 7.1 (Boron)	-

-
-

337

IS 4964 (2013)

Textiles – Vests, cotton, plain (Single jersey) knitted – Specification (fifth revision)

testing charges for the product are Rs 6400/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4/4.1 (MANUFACTURE AND FINISH- Fabric-see IS 9469)	-
4/4.1/4.1.1 (MANUFACTURE AND FINISH- Fabric-The mass of the vest-method given in B-5.)	-
4/4.1/4.1.2 (MANUFACTURE AND FINISH- Fabric-)	-
4/4.1/4.1.3 (MANUFACTURE AND FINISH- Fabric-)	-
4/4.2-Fig. 1A, Fig. 1B, Fig. 2A, Fig. 2B, Fig. 3. (MANUFACTURE AND FINISH)	-
4/4.2/4.2.1 (MANUFACTURE AND FINISH)	-
4/4.3/4.3.2-according to B-4 (MANUFACTURE AND FINISH-Seams and Stitches-Dimension)	-
4/4.3/4.3.3 (MANUFACTURE AND FINISH-Seams and Stitches)	-
4/4.4 (MANUFACTURE AND FINISH)	-
4/4.6 (MANUFACTURE AND FINISH-Freedom from Defects)	-
5/5.1-Tables 2 and 3 (REQUIREMENTS-Dimensions-method prescribed in Annex B.)	-

-
Excluding Table 4: Rubbing, , 4.1 Fabric

338

IS 2888 (2004)

Toilet soap - Specification (Third Revision)

- View breakup
Rs. 4050/- each for Gr.1 & Gr.2 Rs. 4700/- for Gr.3

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.5, Table-1 (vii), Grade-3 (Lather)	-
5.5, Table-1 (vii), Grade-2 (Lather)	-
5.5, Table-1 (vii), Grade-1 (Lather)	-
5.5, Table-1 (vi), Grade-1, Grade-2 & Grade-3 (Free carbonated alkali)	-
5.5, Table-1 (v), Grade-1, Grade-2 & Grade-3 (Chloride (as sodium chloride), IS 286)	-
5.5, Table-1 (iv), Grade-2 & Grade-3 (Matter insoluble in alcohol, IS 286)	-
5.5, Table-1 (iv), Grade-1 (Matter insoluble in alcohol, IS 286)	-
5.5, Table-1 (iii), Grade-1, Gr-2 & Gr-3 (Free caustic alkali, as sodium hydroxide (NaOH), IS 286)	-
5.5, Table-1 (ii), Grade-1, Gr-2 & Gr-3 (Rosin acids, percent by mass of total fatty matter, IS 286 )	-
5.5, Table-1 (i), Grade-3 (Total fatty matter, IS 286)	-
5.5, Table-1 (i), Grade-2 (Total fatty matter, IS 286)	-
5.5, Table-1 (i), Grade-1 (Total fatty matter, IS 286)	-
5.5, Table-1 (vii), Grade-3 (Lather)	-
5.5, Table-1 (vii), Grade-2 (Lather)	-
5.5, Table-1 (vii), Grade-1 (Lather)	-
5.5, Table-1 (vi), Grade-1, Grade-2 & Grade-3 (Free carbonated alkali)	-
5.5, Table-1 (v), Grade-1, Grade-2 & Grade-3 (Chloride (as sodium chloride), IS 286)	-
5.5, Table-1 (iv), Grade-2 & Grade-3 (Matter insoluble in alcohol, IS 286)	-
5.5, Table-1 (iv), Grade-1 (Matter insoluble in alcohol, IS 286)	-
5.5, Table-1 (iii), Grade-1, Gr-2 & Gr-3 (Free caustic alkali, as sodium hydroxide (NaOH), IS 286)	-
5.5, Table-1 (ii), Grade-1, Gr-2 & Gr-3 (Rosin acids, percent by mass of total fatty matter, IS 286 )	-
5.5, Table-1 (i), Grade-3 (Total fatty matter, IS 286)	-
5.5, Table-1 (i), Grade-2 (Total fatty matter, IS 286)	-
5.5, Table-1 (i), Grade-1 (Total fatty matter, IS 286)	-

-
Excluding Clause 5.3 Table 1 (vii) Lather

339

IS 7098 : Part 3 (1993)

Cross - Linked polyethylene insulated thermoplastic sheathed cables - Specification: Part 3 for working voltages from 66 kV up to and including 220 kV

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (CONDUCTOR)	-
6 (SCREENING)	-
8.1 (INNER SHEATH)	-
8.2 (INNER SHEATH)	-
8.3 (INNER SHEATH)	-
9.1 (ARMOUR)	-
10.1 (OUTER SHEATH)	-
10.2 (OUTER SHEATH)	-
11.1 (CONDUCTOR)	-
11.2 (CONDUCTOR)	-
12.1 (CONDUCTOR SCREENING )	-
12.2 (CONDUCTOR SCREENING )	-
13.1 (INSULATION)	-
13.2 (INSULATION)	-
14.1 (INSULATION SCREENING)	-
14.2.1 (INSULATION SCREENING : Non-metallic Part)	-
14.2.2 (INSULATION SCREENING : Non-metallic Part)	-
14.2.3 (INSULATION SCREENING : Non-metallic Part)	-
14.3.1 (INSULATION SCREENING : Metallic Part)	-
14.3.2 (INSULATION SCREENING : Metallic Part)	-
14.3.3 (INSULATION SCREENING : Metallic Part)	-
15.1 (MOISTURE BARRIER)	-
15.2.1 (Metallic Sheath)	-
15.2.2 (Metallic Sheath)	-
16.1 (INNER SHEATH)	-
16.2 (INNER SHEATH)	-
17.1 (ARMOUR)	-
17.2 (ARMOUR)	-
17.3 (ARMOUR)	-
17.4 (ARMOUR)	-
17.5 (ARMOUR)	-
18.1 (OUTER SHEATH)	-
18.2 (outer sheath colour)	-
18.3.1 (Thickness of Outer Sheath : Unarmoured Cables)	-
18.3.1 (Thickness of Outer Sheath : armoured Cables)	-
19.1 A) I) (Tests on conductor : Annealing test ( for copper ))	-
19.1 A) II) (Tests on conductor : Resistance test)	-
19.1 g)2) i) (PVC sheath : Tensile strength and elongation at break)	-
19.1 g)2) iii) (PVC sheath : Loss of mass)	-
19.1 g)2) v) (PVC sheath : Hot deformation test)	-
19.1 g)2) vi) (PVC sheath : Shrinkage test)	-
19.1 g)2) vii) (PVC sheath : Thermal stability)	-
20.7 (Flammabihty test ( for PVC outer sheathed cables only ))	-
20.16.2 (Test for Dimensions of Insulation : Test for Eccentricity)	-
20.16.3 (Test for Dimensions of Insulation : Test for Ovality)	-

-
Testing facility not available for 1. Bending test followed by P D test 2. Dielectric power factor and capacitance measurement at ambient temperature 3. Dielectric power factor measurement at elevated temperature 4. Load cycle test followed by P.D measurement 5. Impulse withstand test followed by HV test

340

IS 4355 (1977)

Specification for fire-resistant brattice cloth (first revision)

Please see remarks. View breakup
Rs. 1650/- excluding Fire resistance, Accelerated weathering test, Air permeability, Electrical resistance).

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.3.2 Length and width (The length and width of finshed fabric shall be as agreed between the purchase and the supplier .A Tolerance of - 5% shall be alowed on width)	-
Cl.3.3.1 (The treatment of the base fabric to make it fabric uniformly and adhere firmly to the fabric)	-
Cl.3.3.2 (The treatment material shall penetrate the fabric uniformly and adhere firmly to the fabric.)	-
Cl.3.3.3 (The treated fabric shall have a reasonable durability under all condition of usage )	-
Cl.3.3.4 (The treated fabric shall have any undesirable odour and shall be non irritant to skin)	-
Cl.3.4.2 (The breaking load of the brattice cloth for wrapway and weftway shall not be leass than 40 Kgf and 20 Kgf respectiveely when tested in accordance with IS 1969-1068 on a specimen of 5 cm width)	-

-
Excluding TF not available for Fire resistance, Accelerated weathering test, Air permeability, Electrical resistance

341

IS 6444 (1979)

Specification for sulphur dusting powders (First Revision)

Rs.2100.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.2 Table 1 (Sulphur Content, NV upto 9)	-
2.2 Table 1 (Sulphur Content, NV Above 9 below 50)	-
2.2 Table 1 (Sulphur Content, NV above 50)	-
2.2 Table 1 (Material passing through 75 micron sieve)	-
2.1 (Description)	-
2.2 Table 1 (Bulk Density after compacting)	-
2.2 Table 1 (Sulphur Content, NV upto 9)	-
2.2 Table 1 (Sulphur Content, NV Above 9 below 50)	-
2.2 Table 1 (Sulphur Content, NV above 50)	-
2.2 Table 1 (Material passing through 75 micron sieve)	-
2.1 (Description)	-
2.2 Table 1 (Bulk Density after compacting)	-
2.2 Table 1 (Sulphur Content, NV upto 9)	-
2.2 Table 1 (Sulphur Content, NV Above 9 below 50)	-
2.2 Table 1 (Sulphur Content, NV above 50)	-
2.2 Table 1 (Material passing through 75 micron sieve)	-
2.1 (Description)	-
2.2 Table 1 (Bulk Density after compacting)	-

-
-

342

IS 651 (2007)

Glazed stoneware pipes and fittings - Specification (Sixth Revision)

Rs. 6850/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (GENERAL QUALITY)	-
5.2(a) (GENERAL QUALITY)	-
5.2(b) (GENERAL QUALITY)	-
5.2(c) (GENERAL QUALITY)	-
6 ( GLAZING)	-
7.2 (Hydraulic Test)	-
7.3 (Absorption Test)	-
10.1-Table 1 (INTERNAL DIAMETER)	-
10.1-Table 1 (Class)	-
11.1-Table 1 ( Mean Thickness of Barrel and of Socket)	-
14-Table 1 (Internal Depth of Socket)	-
14-Table 2 (Excess Shoulder Measurment)	-
14-Table 3 (Length of Grooving of Spigot)	-
12.4 (Permissible Deviation from Straightness)	-
12.2 (STRAIGHTNESS OF BARRELS OR STRAIGHT AND TAPER PIPES-Length of Junction)	-
13.1-Table 2 (Dimensions of One-Quarter Bends-Internal Diameter)	-
13.1-Table 2 (Dimensions of One-Quarter Bends-r)	-
13.1-Table 2 (Dimensions of One-Quarter Bends-angle)	-
13.1-Table 3 (Dimensions of One-Eighth Bends--Internal Diameter)	-
13.1-Table 3 (Dimensions of One-Eighth Bends-r)	-
13.1-Table 3 (Dimensions of One-Eighth Bends-angle)	-
13.1-Table 4 (Dimension of One-Sixteenth Bends-Internal Diameter)	-
13.1-Table 4 (Dimension of One-Sixteenth Bends-r)	-
13.1-Table 4 (Dimension of One-Sixteenth Bends-angle)	-

-
Complete for chemical

343

IS 16333 : Part 3 (2017)

Mobile phone handsets: Part 3 indian language support for mobile phone handsets - Specific requirements (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (Inputting of text)	-
5.2 (Message Readability)	-

-
-

344

IS 2980 (1999)

Non - Pressure stoves - Specification (Third Revision)

- View breakup
Rs. 5400/- and Material testing charges as per respective Iss

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.0 (MATERIAL)	-
5.1 (construction of the stoves)	-
5.2 (Fuel Leakage)	-
5.3 (Fuel container)	-
5.4 (Knob fro winding)	-
5.5 (Various components of stoves of one make)	-
5.6 (Perforated Sleeves)	-
5.8 (For Single-Wick and Multi-Wick Stoves)	-
6.2 (Thermal Efficiency Test)	-
6.3 (Combustion Efficiency)	-
6.4 (Flame Stability Test)	-
6.5 (Fuel Creep)	-
6.6 (Surface Temperature Test)	-
6.7 (Fuel Temperature Test)	-
6.8 (Flame Flash-Back Test)	-
6.9 (Stability Test)	-

-
-

345

IS 2039 : Part 1 to 3 (1991)

Steel tubes for bicycle and cycle rickshaws - Specification (Second Revision)

Rs.4320.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 6.1 (Workmanship)	-
Cl. 6.2 (Fin Height)	-
Cl. 6.3 (Straightness)	-
Cl. 8.1 (Tensile Strength)	-
Cl. 8.1 (Yield Strength)	-
Cl. 8.1 (Elongation)	-
Cl. 8.2 (Drift Expansion Test- IS 2335)	-
Cl. 8.3 (Flattening Test-IS 2338)	-
Cl. 9 (Diameter)	-
Cl. 9 (Thickness)	-
Cl. 3.2.1, Table 4 (Yield Stress)	-
Cl. 3.2.1, Table 4 (UTS)	-
Cl. 3.2.1, Table 4 (Elongation)	-
Cl. 3.2.2, Table 2 (Drift Expansion Test- IS 2335)	-
Cl. 3.2.3, Table 3 (Flattening Test-IS 2338)	-
Cl. 4.2.1 (Diameter)	-
Cl. 4.2.2 (Thickness)	-
Cl. 4.2.3 (Length)	-
Cl. 4.2.1, Table 7 (Yield Stress)	-
Cl. 4.2.1, Table 7 (UTS)	-
Cl. 4.2.2, Table 8 (Drift Expansion Test- IS 2335)	-
Cl. 4.2.3, Table 9 (Flattening Test-IS 2338)	-
Cl. 5.2.1, Table 10 (Diameter)	-
Cl. 5.2.2 (Mean Thickness)	-
Cl. 5.2.3, Table 6 (Length)	-
Cl. 5.1 Table 1 (Carbon)	-
Cl. 5.1 Table 1 (Silicon)	-
Cl. 5.1 Table 1 (Manganese)	-
Cl. 5.1 Table 1 (Phosphorous)	-
Cl. 5.1 Table 1 (Sulphur)	-

-
-

346

IS 2257 (1989)

Paper adhesives, liquid gum and office paste type - Specification (Third Revision)

Rs 5280/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 4.2 Table 1 (v) (Keeping Quality )	-
Clause 4.2 Table 1 (v) (Stability at 37°C)	-
4.1 (Description)	-
Clause 4.2 Table 1 (iv) (Brittleness and moisture absorption of the dried film)	-
Clause 4.2 Table 1 (ii) (pH)	-
Clause 4.2 Table 1 (i) (Total Solid)	-
4.3 (Keeping quality)	-
Table 1 (i), 4.2 (Total solids)	-
Table 1 (ii), 4.2 (pH value)	-
Table 1 (iv), 4.2 (brittleness and moisture absorption of the dried film)	-
Table 1 (v), 4.2 (stability at 37C)	-

-
-

347

IS 1891 : Part 1 (1994)

Conveyor and elevator textile belting - Specification: Part 1 general purpose belting (Fourth Revision)

6600 View breakup
Rs. 6600/- excluding abrasion loss and troughability.

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
14.2.2 (Elongation at breaking load)	-
14.2.1 (Elongation at reference load)	-
14.1 (Full thickness breaking strength)	-
13.2 (Width)	-
13.1 (Length)	-
8.2 (Carcass Thickness)	-
8.1 (Cover Thickness)	-
7.4 (Rubber cover abrasion)	-
7.3 (Cover Elongation at break heat Ageing)	-
7.3 (Cover tensile strength heat Ageing)	-
7.2 (Thickness)	-
7.1 (Cover Elongation at break)	-
7.1 (Cover tensile strength)	-

-
-

348

IS 539 (1974)

Specification for naphthalene (Second Revision)

- View breakup
i) For Grade1 = 8.5X300 + 15.5X 9 + 800 = 3489 /- (Rounded off Rs.3490/-) ii) For Grade2 = 13.5X300 + 20X9 + 1100 = 5330/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.3 Table 1 (Ash, all grades)	-
4.3 Table 1 (Matter Insoluble in Benzene, all grades)	-
4.3 Table 1 (Non-volatile matter, all grades)	-
4.3 Table 1 (Moisture, all grades)	-
4.3 Table 1 (Crystallization point, Grade 2)	-
4.3 Table 1 (Crystallization point, Grade 1)	-
4.1.1 (Description, Grade 1)	-
4.1.2 (Description, Grade 2)	-
4.3 Table 1 (Total Sulphur, Grade 2)	-
4.2 (Test for Staining)	-
4.3 Table 1 (Colour, grade 1)	-
4.3 Table 1 (Colour, grade 2)	-
4.3 Table 1 (Acid wash Test, Grade 1)	-
4.3 Table 1 (Ash, all grades)	-
4.3 Table 1 (Matter Insoluble in Benzene, all grades)	-
4.3 Table 1 (Non-volatile matter, all grades)	-
4.3 Table 1 (Moisture, all grades)	-
4.3 Table 1 (Total Sulphur, Grade 2)	-
4.3 Table 1 (Crystallization point, Grade 2)	-
4.3 Table 1 (Crystallization point, Grade 1)	-
4.1.1 (Description, Grade 1)	-
4.1.2 (Description, Grade 2)	-
4.2 (Test for Staining)	-

-
-

349

IS 2547 : Part 1 (1976)

Specification for gypsum building plaster: Part 1 excluding premixed lightweight plasters

- View breakup
i) Plaster of paris (Type A) 18x300 = Rs.5400.00 (Type B) 22x300 = Rs.6600.00 ii) Anhydrous Gypsum Plaster 14x300 = Rs.4200.00 iii) Keene’s Plaster 16x300 = Rs.4800.00

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 4.1, Table-1 (Beta hemihydrate, SO3)	-
Clause 4.1, Table-1 (Beta hemihydrate, CaO)	-
Clause 4.1, Table-1 (Beta hemihydrate, Soluble magnesium salts as MgO)	-
Clause 4.1, Table-1 (Beta hemihydrate, Soluble sodium salts as Na2O)	-
Clause 4.1, Table-1 (Beta hemihydrate,. Loss of ignition)	-
Clause 4.1, Table-1 (Retarded Hemihydrate Gypsum Plaster, SO3)	-
Clause 4.1, Table-1 (Retarded Hemihydrate Gypsum Plaster, CaO)	-
Clause 4.1, Table-1 (Beta hemihydrate, Soluble magnesium salts as MgO)	-
Clause 4.1, Table-1 (Retarded Hemihydrate Gypsum Plaster, Soluble sodium salts as Na2O)	-
Clause 4.1, Table-1 (Retarded Hemihydrate Gypsum Plaster, Loss of ignition)	-
Clause 4.1, Table-1 (Retarded Hemihydrate Gypsum Plaster, Free lime)	-
Clause 4.1, Table-1 (Anhydrous Gypsum plaster,. SO3)	-
Clause 4.1, Table-1 (Anhydrous Gypsum plaster,. CaO)	-
Clause 4.1, Table-1 (Anhydrous Gypsum plaster,. Soluble magnesium salts as MgO)	-
Clause 4.1, Table-1 (Anhydrous Gypsum plaster,. Soluble sodium salts as Na2O)	-
Clause 4.1, Table-1 (Anhydrous Gypsum plaster,. Loss on ignition)	-
Clause 4.1, Table-1 (Keene's Plaster, SO3)	-
Clause 4.1, Table-1 (Keene's Plaster, CaO)	-
Clause 4.1, Table-1 (Keene's Plaster, Soluble magnesium salts as MgO)	-
Clause 4.1, Table-1 (Keene's Plaster, Soluble sodium salts as Na2O)	-
Clause 4.1, Table-1 (Keene's Plaster, Loss of ignition)	-
Clause 4.1, Table-1 (Beta hemihydrate, SO3)	-
Clause 4.1, Table-1 (Beta hemihydrate, CaO)	-
Clause 4.1, Table-1 (Beta hemihydrate, Soluble magnesium salts as MgO)	-
Clause 4.1, Table-1 (Beta hemihydrate, Soluble sodium salts as Na2O)	-
Clause 4.1, Table-1 (Beta hemihydrate,. Loss of ignition)	-
Clause 4.1, Table-1 (Retarded Hemihydrate Gypsum Plaster, SO3)	-
Clause 4.1, Table-1 (Retarded Hemihydrate Gypsum Plaster, CaO)	-
Clause 4.1, Table-1 (Beta hemihydrate, Soluble magnesium salts as MgO)	-
Clause 4.1, Table-1 (Retarded Hemihydrate Gypsum Plaster, Soluble sodium salts as Na2O)	-
Clause 4.1, Table-1 (Retarded Hemihydrate Gypsum Plaster, Loss of ignition)	-
Clause 4.1, Table-1 (Retarded Hemihydrate Gypsum Plaster, Free lime)	-
Clause 4.1, Table-1 (Anhydrous Gypsum plaster,. SO3)	-
Clause 4.1, Table-1 (Anhydrous Gypsum plaster,. CaO)	-
Clause 4.1, Table-1 (Anhydrous Gypsum plaster,. Soluble magnesium salts as MgO)	-
Clause 4.1, Table-1 (Anhydrous Gypsum plaster,. Soluble sodium salts as Na2O)	-
Clause 4.1, Table-1 (Anhydrous Gypsum plaster,. Loss on ignition)	-
Clause 4.1, Table-1 (Keene's Plaster, SO3)	-
Clause 4.1, Table-1 (Keene's Plaster, CaO)	-
Clause 4.1, Table-1 (Keene's Plaster, Soluble magnesium salts as MgO)	-
Clause 4.1, Table-1 (Keene's Plaster, Soluble sodium salts as Na2O)	-
Clause 4.1, Table-1 (Keene's Plaster, Loss of ignition)	-

-
Test method is not specified. Excluding Table 1,Clause 4.1 ,sl. no.(iii)&(iv) , soluble Mgo & Na2o salts.

350

IS 15609 (2005)

Polyethylene flexible pouches for the packing of natural mineral water and packaged drinking water - Specification

Rs.6900/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1 Annex E (Water Potability test (after 30 Days) a) Taste b) Odour)	-
6.1.7 IS: 9845:1998 (Migration- a. Amount of extractive )	-
7.5 Annex J (Product resistance test for printed pouches)	-
7.4 Annex H (Ink adhesion test for printed pouches)	-
7.3 Annex G (Drop test )	-
7.2 Annex F (Stack Load test)	-
6.1.10 Annex -6 of IS:2508:2016 (Dart impact Resistance)	-
6.1.9 Annex 4 of IS:2508:2016 (Elongation at break - b. Crosswise direction)	-
6.1.9 Annex 4 of IS:2508:2016 (Elongation at break - a. Lengthwise direction)	-
6.1.8 Annex 4 of IS:2508:2016 (Tensile Strength b. Crosswise direction)	-
6.1.8 Annex 4 of IS:2508:2016 (Tensile Strength a. Lengthwise direction)	-
6.1.6 (Width)	-
6.1.5 A-2 of IS: 2508:2016 (Thickness)	-
6.1.4 (Odour)	-
6.1.3 (Winding of the Film )	-
6.1.2 (Film Form)	-
6.1.1 (Description)	-
5 (Material)	-
Cl. 7.1 (Vibration Leakage Test)	-

-
3L Complete for chemical Excluding 6.1.8 Tensile Strength, 6.1.9 Elongation at Break, 6.1.10 Dart Impact Resistance

351

IS 15914 (2011)

High tensile strength flat rolled steel plate (Up To 6 Mm), sheet and strip for the manufacture of welded gas cylinder - Specification

Rs. 7760/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 7 (UTM)	-
Cl 9 (Workmanship)	-
Cl 10 (Length, Width & Thickness)	-
Cl. 7 Table 3 (Elongation)	-
Cl. 7 Table 3 (Yield Stress)	-
6.0 (CARBON)	-
6.0 (SULPHUR)	-
6.0 (PHOSPHORUS)	-
6.0 (MANGANESE)	-
6.0 (SILICON)	-
6.0 (ALUMINIUM)	-
6.0 (NITROGEN)	-
6.0 (MICRO ALLOYING)	-

-
-

352

IS 7123 (2019)

Hair oils - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause no 4.4/Annex A (A-3) (4 Examination)	-
Clause 4.5 (Peroxide Value)	-
Clause 4.6 (Arsenic Oxide)	-
Clause 4.6 (Lead)	-
Clause 4.3 (Acid Value)	-
Clause 4.1 (Description)	-
4.3, A-2.2 (Acid value)	-
4.5, A-4 (Peroxide value)	-
4.6, A-4 (Heavy metals)	-

-
-

353

IS 4457 (2007)

Ceramic unglazed vitreous acid resisting tiles - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3 (MANUFACTURE)	-
5-Table 1(i)-a (REQUIREMENTS-Dimensions and Surface Quality-Length)	-
5-Table 1(i)-a (REQUIREMENTS-Dimensions and Surface Quality-Width)	-
5-Table 1(i)-b (REQUIREMENTS-Dimensions and Surface Quality-Thickness)	-
5-Table 1(ii) (REQUIREMENTS-Surface Quality)	-

-
-

354

IS 3104 : Part 1 (1982)

Specification for density hydrometers: Part 1 requirements (First Revision)

Rs. 4800/- excluding accuracy test. View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.11.2 ( Stem diameter of the hydrometers shall be not less than 40 mm.)	-
Cl.9.1 Bulb and Stem ( — The bulb and the stem shall be made of a suitable transparent glass, selected and processed to be as free as possible from stress and visible defects, and having a coefficient of cubical thermal expansion of (25 ± 2) × 10-6 (°C)-)	-
Cl.9.2 Loading Material ( — The loading material shall be fixed in the bottom of the hydrometer. After the finished hydrometer has been kept in a horizontal position for 1 h at 80°C and subsequently cooled in that position, the instrument shall meet the requirements of 10.3.)	-
Cl.9.3 Scale Strip ( — The strip on which the scale and inscriptions are marked shall have a smooth matt surface. The strip shall show no evidence of charring, and shall not become discoloured or distorted when the stem is exposed for 1 h to a temperature of 80°C.)	-
Cl.10.1 workmanshisp and finish ( The outer surface of the hydrometers shall be symmetrical about the main axis)	-
Cl.10.2 ( There shall be no abrupt changes in their cross section ( see Fig, 1 ))	-
Cl.10.3 ( The cross-section of the stem shall remain unchanged for at least 5 mm below the lowest graduation line on ??? scale.)	-
Cl.10.4 (The stem shall extend unchanged in diameter at least 15 mm above the uppermost graduation line on the scale.)	-
Cl.10.5 ( The hydrometer shall float with its axis vertical to within 1.5° of arc.)	-
Cl.10.6 (There shall be no loose material in the instrument)	-
Cl.10.7 ( The strip on which the scale and inscriptions are marked shall remain securely fastened in place at the temperature of use ( see 9.3 ).)	-
Cl.10.8 ( The scale shall be straight and without twist.)	-
Cl.10.9 ( Appropriate means shall be incorporated for ensuring that any displacement of the scale or of the strip bearing the scale is readily apparent.)	-
Cl.11.1 ( The dimensions of the hydrometers shall conform to the requirements given in Table 1.)	-
Cl.12.2 Cl.12.2.1 Graduation Lines ( The graduation lines shall be distinct and of uniform thickness not exceeding 0 2 mm or one-fifth of the distance between the centres of adjacent lines, whichever is less. For the SP series, the thickness of the graduation lines shall not exceed 0.2 mm or one-sixth of the distance between the centres of adjacent lines, whichever is less.)	-
Cl.12.2.2 (There shall be no evident local irregularities in the spacing of the graduation lines.)	-
Cl.12.2.3 ( The graduation lines shall be perpendicular to the axis of the hydrometer.)	-
Cl.12.2.4 (The short, medium and long scale lines shall extend, respectively, at least one-fifth, one-third and one-half of the way round the circumference of the stem.)	-
Cl.12.2.5 ( The highest and lowest graduation lines indicating the nominal limits of the scale shall be long lines ( see 12.3.1, 12.3.2 and 12.3.3 ).)	-
Cl.12.2.6 ( The short, medium and long lines shall each be vertically disposed so that either the mid-points, or the right hand ends or the left hand ends of all graduation lines He on an imaginary line parallel to the axis of the instrument. In the latter two cases, the vertical line may, alternatively, be marked.)	-
Cl.12.3.1 Sequence of Graduation Lines ( On hydrometer scales whose smallest interval is 1 kg/m3 or 1 g/ml:)	-
Cl.12.3.2 ( On hydrometer scales whose smallest interval is 2 kg/m3, or 2 g/ml)	-
Cl.12.3.3 ( On hydrometer scales whose smallest interval is 5 kg/m3 or 5 g/ml:)	-
Cl.12.4 Figuring of Graduation Lines Cl.12.4.0 ( The scale lines and inscriptions should preferably be black and shall be clearly and durably marked.)	-
Cl.12.4.1 ( The scale shall have only one set of numbers and the last digits of the numbers shall be vertically aligned ( see Fig. 2 ).)	-
Cl.12.4.2 ( The scale shall be so figured as to enable the value corresponding to any graduation line to be readily identified.)	-
Cl.12.4.3 ( The highest and lowest graduation lines of the nominal limits shall be figured in full.)	-
Cl.12.4.4 ( At least every tenth line shall be figured)	-
Cl.12.4.5 ( For density values expressed in grams per cubic centimetres, the decimal sign shall be included for numbers expressed in full, but may be omitted from abbreviated numbers.)	-
Cl.12.5 Extension of Scale ( — The scale shall be extended beyond the nominal scale limits, as indicated in col 12 of Table 1.)	-
3.0 (BASIS OF SCALE)	-
4.1 (Series)	-
4.2 (Ranges)	-
5.0 (REFERENCE TEMPERATURE)	-
6.0 (SURFACE TENSION)	-
7.0 (REFERENCE LEVELS FOR ADJUSTMENT AND READING)	-
8.0 (IMMERSION)	-
11.1, 12.5, Table 1 (SERIES)	-
11.1, 12.5, Table 1 (MAXIMUM TOTAL LENGTH)	-
11.1, 12.5, Table 1 (NOMINAL RANG E OF EACH HYDROMETER)	-
11.1, 12.5, Table 1 (NUMBER OF SCALE DIVISIONS × VALU E OF THE SCALE INTERNAL, g/ml)	-
11.1, 12.5, Table 1 (NUMBER OF SCALE DIVISIONS × VALU E OF THE SCALE INTERNAL, kg/m3)	-
11.1, 12.5, Table 1 (NUMBER OF SCALE DIVISIONS × VALU E OF THE SCALE INTERNAL, g/ml)	-
11.1, 12.5, Table 1 (MINIMUM SCALE LENGTH (NOMINAL RANGE))	-
11.1, 12.5, Table 1 (BULB DIA - METER, Max.)	-
11.1, 12.5, Table 1 (BULB DIA - METER, Min.)	-
11.1, 12.5, Table 1 (VOLUME BELOW LOWEST GRADUATIO N LIN E OF NOMINAL RANGE, Max.)	-
11.1, 12.5, Table 1 (VOLUME BELOW LOWEST GRADUATIO N LIN E OF NOMINAL RANGE, Min.)	-
11.1, 12.5, Table 1 (EXTENSION OF SCALE AT EACH AND BEYOND UPPER AND LOWER NOMINAL LIMITS)	-
12.0 (General)	-
12.1 (Recommended scales)	-

-
No chemical requirements. Excluding Cl13. ACCURACY

355

IS 13620 (1993)

Fusion Bonded Epoxy Coated Reinforcing Bars -

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Carbon- IS 228(Part 1))	-
4.1 (Sulphur- IS 228(Part 9))	-
4.1 (Phosphorous- IS 228(Part 3))	-
4.1 (Nitrogen- IS 228(P-19))	-
4.1 (Sulphur & Phosphorous)	-
4.1 (Carbon Equivalent)	-
Cl 7.1 (Coating Thickness)	-
Cl 7.1 (Coating Thickness)	-

-
-

356

IS 15801 (2008)

Polypropylene - Random copolymer pipes for hot and cold water supplies - Specification

4200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 4 ( Designation)	-
Cl 7 (Dimensions Of Pipes)	-
Cl 8 (Visual Appearance)	-
Cl 9.3 (Reversion Test )	-
Cl 9.5 (Density)	-
Cl 9.6 (Melt Flow Rate)	-

-
Excluding Test Facility not available for Cl.9.1 Hydraulic characterestics(Internal, creep, rupture), Cl 9.4 Impact Strength

357

IS 12916 (1990)

Acephate SP- Specification

Rs.2000.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (Description)	-
3.3.1 Table 1 i (Acephate Content)	-
3.3.1 Table 1 ii (Acidity (as H2SO4))	-

-
-

358

IS 4521 (2001)

Wire ropes used in oil wells and oil well drilling - Specification (Second Revision)

Rs.7750/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (tables 1 to 10) (Size)	-
5 (tables 1 to 10) (Minimum Breaking Force)	-
6 (General Requirements)	-
6.1 (GENERAL)	-
6.2 (Core)	-
6.3 (Joints)	-
6.4 (Mass)	-
6.5 (Lay of the Rope)	-
6.6 (Length of Lay)	-
7 (Galvanizing)	-
8 (Lubrication)	-
6 (General Requirements)	-
Clause - 4 (CARBON)	-
Clause - 4 (SULPHUR)	-
Clause - 4 (PHOSPHURS)	-
Clause - 4 (MANGANESE)	-
Clause - 4 (SILICON)	-
Clause - 4 (ALUMINIUM)	-
Clause - 4 (NITROGEN)	-

-
Excluding cl 5 minimum breaking force for nominal dia 1 to 18 mm and above 22 mm

359

IS 1321 : Part 1 (2003)

Sisal ropes – Specification Part 1 Untarred varieties (fourth revision)

4800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5.6 (Rot-Proofing Treatment)	-
5.5 (Lubrication Weighing or loading materials shall not be used. For the purpose of dressing the fibre or for the preservation of the rope, a lubricant shall be added preferably petroleum products. The quantity of dressing applied to the fibre shall be neither less than 10 percent nor more than 15 percent calculated on the mass of the finished rope when determined by extraction with petroleum ether or other solvent.)	-

-
-

360

IS 6760 (1972)

Specification for slotted countersunk head wood screws

Rs.900.0 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1, Table 1 (Screw No. (Screw Design))	-
3.1, Table 1 (Diameter of Unthreaded Shank d, Nominal)	-
3.1, Table 1 (Diameter of Unthreaded Shank d, maximum)	-
3.1, Table 1 (Diameter of Unthreaded Shank d, Minimum)	-
3.1, Table 1 (Pitch)	-
3.1, Table 1 (Diameter of Head, D, Maximum)	-
3.1, Table 1 (Diameter of Head, D, Minimum)	-
3.1, Table 1 (Depth of Head c†, maximum)	-
3.1, Table 1 (Depth of Head c†, minimum)	-
3.1, Table 1 (Width of Slot s, maximum)	-
3.1, Table 1 (Width of Slot s, minimum)	-
3.1, Table 1 (Depth Slot n‡, Maximum)	-
3.1, Table 1 (Depth Slot n‡, Mainimum)	-
4.0 (Designation)	-
5.0 (General Requirements)	-

-
-

Bureau of Indian Standards

The National Standards Body of India

BIS, Central Laboratory (CL)

20/9, Site 4, Sahibabad Industrial Area, Sahibabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201010

- sample@bis.gov.in

Scope List