BIS - LIMS (Laboratory Information Management System)

BIS, Eastern Regional Laboratory (ERL)

(1) Annex Building & Sample-Cell: Bureau of Indian Standards, P-230, CIT Scheme, VII- M, Block-W,Kankurgachi,Kolkata-700054 (2) Main building: 1/14, CIT Scheme VII M, VIP Road, Kankurgachi,Kolkata-700054, Kolkata, Kolkata, West Bengal, 700054

- sample.erol@bis.gov.in

Scope List

Reset

370 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

301

IS 6529 (1996)

Stainless steel blooms, billets and slabs for forging - Specification (First Revision)

All grades except for the elements mentioned in remarks

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1,7.2,7.3 Table 1 (Carbon-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
7.1,7.2,7.3 Table 1 (Silicon-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
7.1,7.2,7.3 Table 1 (Manganese-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
7.1,7.2,7.3 Table 1 (Phosphorous-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
7.1,7.2,7.3 Table 1 (Sulphur-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
7.1,7.2,7.3 Table 1 (Molybdenum-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
7.1,7.2,7.3 Table 1 (Chromium-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
7.1,7.2,7.3 Table 1 (Nickel-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
7.1,7.2,7.3 Table 1 (Niobium-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
7.1,7.2,7.3 Table 1 (Titanium-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
7.1,7.2,7.3 Table 1 (Others(Nitrogen)-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
13 (Corrosion Resistance- IS 10461(Part1))	-
13 (Corrosion Resistance- IS 10461(Part2))	-
6 (Freedom from defects)	-
9 (Hardness)	-
10 (Dimensional Tolerances)	-

-
Chem- Facility not available for Ta, Se, Wire Diameter Should be Greater than 3 mm Steel designation and element specified in Cl.7.3

302

IS 1875 (1992)

Carbon steel billets, blooms, slabs and bars for forgings - Specification (Fifth Revision)

all class/designations

Rs.5400/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 7 (Workmanship)	-
Cl 8 (Diameter, Ovality & Weight)	-
Cl 9 (UTM & HBW)	-
6.1, 6.2 (carbon)	-
6.1, 6.2 (silicon )	-
6.1, 6.2 (manganese)	-
6.1, 6.2 (sulphur)	-
6.1, 6.2 (phosphorus)	-
6.1, 6.2 (molybdenum)	-
6.1, 6.2 (copper)	-
6.1, 6.2 (cromium)	-
6.1, 6.2 (nickel)	-
6.1, 6.2 (aluminium)	-
12.0 & 12.3 (Grain Size - IS 4748)	-
12.0 & 12.4 (Macrostructure- IS 11371)	-
CL 8.0 (Average dia (08))	-

-
Facility not available for B, V, Sn Mech- Except Cl 12 Supplementary Requirements (ultrasonic, magnetic particle test) Remarks: Type of killing & killing material, element as per Cl 6.3 ( if applicable) & Class/Designation, cross sectional dimension to be declared.

303

IS 14494 (2019)

Elastomer insulated flexible cables for use in mines - Specification (First Revision)

All types

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (CONDUCTOR)	-
5 (INSULATION)	-
5.1 (Power Cores)	-
5.2 (Pilot and Earth Cores)	-
6 (SEMI-CONDUCTING COMPOUND)	-
4 (CONDUCTOR)	-
5 (INSULATION)	-
5.1 (Power Cores)	-
5.2 (Pilot and Earth Cores)	-
6 (SEMI-CONDUCTING COMPOUND)	-
7.1 (TAPE : Proofed Tape)	-
7.2 (TAPE : Polyethylene Terephalate (PETP) or Polypropylene Base Tape)	-
7.3 (TAPE )	-
8 (CENTRE)	-
9.1 (FILLERS)	-
9.2 (FILLERS)	-
10 (CRADLE SEPARATOR)	-
11.1 (ARMOUR)	-
11.2 a) (ARMOURING: Tensile Strength)	-
11.2 b) (ARMOURING: Elongation )	-
11.2 c) (ARMOURING: Torsion Test (For round wire ) )	-
11.2 d) (ARMOURING: Uniformity of zinc coating)	-
11.2 e) (ARMOURING: Mass of zinc coating )	-
12.1 (SHEATH : Inner Sheath)	-
12.2 (SHEATH : Outer Sheath)	-
13.1 (REINFORCEMENT MATERIAL : Tape)	-
13.2 (REINFORCEMENT MATERIAL : Cord/Yarns)	-
14.1 (CONSTRUCTION : CONDUCTOR)	-
15 (CONDUCTOR SCREENING)	-
16.1 (INSULATION)	-
16.2 (INSULATION : Thickness of Insulation)	-
16.3 (INSULATION : Tolerance on Insulation Thickness)	-
16.4 (INSULATION : Application of Insulation)	-
17.2 (INSULATION SCREEN)	-
18 (PROTECTIVE SCREEN)	-
20.1 (CORE IDENTIFICATION)	-
20.2 (Colour Scheme for Identification)	-
20.3 (Scheme for Identification by Numbering)	-
21.1 (LAYING UP OF CORES)	-
21.2 (LAYING UP OF CORES)	-
21.4 (LAYING UP OF CORES)	-
22.1 (INNER SHEATH)	-
22.2 (Thickness of Inner Sheath)	-
22.3 (INNER SHEATH)	-
23.1 (ARMOURING)	-
23.2 (ARMOURING)	-
23.4 (ARMOURING)	-
24.1 (OUTER SHEATH)	-
24.2 (Thickness of Outer Sheath)	-
24.3 (Tolerance on Thickness of Outer Sheath)	-
24.4 (OUTER SHEATH)	-
25.1 (CABLE CONSTRUCTION AND DIMENSIONS)	-
27.8 (Flammability Test)	-
28 (IDENTIFICATION)	-
29.1 (PACKING AND MARKING)	-
30 (BIS CERTIFICATION MARKING)	-
27.9 (Water Absorption Test)	-

-
Facility not available for ozone resistance test, dielectric pf test, Water Absorption Test, Hot set Test, Oil Resistance Test, Tear Resistance, Ageing in air bomb, bending Test, Heating cycle and partial discharge Test . Facility for High Voltage test is upto 3.3. kV only. Cable type to be declared.

304

IS 6392 (2020)

Steel Pipes Flanges — Specification ( First Revision )

Rs 3070/- + View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 Table 1 (Carbon- relevant parts of IS 228 or any other established instrumental/chemical method, )	-
3.1 Table 1 (Silicon- relevant parts of IS 228 or any other established instrumental/chemical method, )	-
3.1 Table 1 (Manganese- relevant parts of IS 228 or any other established instrumental/chemical method, )	-
3.1 Table 1 (Sulphur- relevant parts of IS 228 or any other established instrumental/chemical method, )	-
3.1 Table 1 (Phosphorous- relevant parts of IS 228 or any other established instrumental/chemical method, )	-
3.1 Table 1 (Nickel- relevant parts of IS 228 or any other established instrumental/chemical method, )	-
6.1 (Dimension)	-
14 (Workmanship)	-
3.1 Table 1 (Carbon Equivalent-relevant parts of IS 228 or any other established instrumental/chemical method,)	-
3.1 Table 1 (Copper- relevant parts of IS 228 or any other established instrumental/chemical method, )	-
3.1 Table 1 (Nitrogen Content-relevant parts of IS 228 or any other established instrumental/chemical method,)	-
3.1 Table 1 (Cr+Ni+Mo- relevant parts of IS 228 or any other established instrumental/chemical method, )	-
3.1 Table 1 (Boron- relevant parts of IS 228 or any other established instrumental/chemical method, )	-
3.1 Table 1 (Niobium-relevant parts of IS 228 or any other established instrumental/chemical method,)	-
3.1 Table 1 (Vanadium- relevant parts of IS 228 or any other established instrumental/chemical method, )	-
3.1 Table 1 (Titanium-relevant parts of IS 228 or any other established instrumental/chemical method,)	-

-
Mech-Facility not available for hydraulic test, For chemical testing, only- C, S, P, Mn, Si, Ni, Cr can be tested. Facility available upto 125 mm bore size. Type/grade/std number for flange material, class designation to be declared.

305

IS 1943 (1995)

Textiles – A-twill jute bags (second revision)

Rs4100/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Sacking- IS 1943)	-
4.1 (Sacking- IS 1943)	-
4.2 (Seam -- IS 1943)	-
4.2 (Seam -- IS 1943)	-
4.2 (Seam -- IS 1943)	-
4.2 (Seam -- IS 570)	-
4.3 (Safety Stitches -IS 1943)	-
4.3 (Safety Stitches -IS 1943)	-
4.3 (Safety Stitches -IS 570)	-
4.4 (Hemming at the mouth IS 9113)	-
4.4 ( IS 570)	-
4.5 (Joined bag - IS 9113)	-
4.6 (Freedom from defects- IS 1943)	-
4.1,5.1,Table 1 (Dimension;Outside Length-IS 9113)	-
4.1,5.1,Table 1 (Dimension;Outside width-IS 9113)	-
4.1,5.1,Table 1 (Ends /dm -IS 1963)	-
4.1,5.1,Table 1 (Picks/dm -IS 1963)	-
4.1,5.1,Table 1 (Corrected Mass/Bag,g-IS 9113)	-
4.1,5.1,Table 1 (Average Breaking Strength in N -IS 1969 N)	-
4.1,5.1,Table 1 (Average breaking load of seam-IS 9030)	-
4.1,5.1,Table 1 (Moisture Regain, Percent-IS 9113)	-
4.1,5.1,Table 1 (Oil content, Percent-IS 2969)	-

-
2m-jute fabric,1m-twin to be provided with bags.

306

IS 4923 (2017)

Hollow steel sections for structural use - Specification (Third Revision)

All grades (please see remarks)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.7.1 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.7.1 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.7.1 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.7.1 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.7.1 (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.7.1 (Carbon Equivalent-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.7.1 (Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.9.1, Table 1 (Dimensions and Properties of Hollow Sections (Depth))	-
Cl.9.1, Table 1 (Dimensions and Properties of Hollow Sections (Width))	-
Cl.9.1, Table 1 (Dimensions and Properties of Hollow Sections(Thickness))	-
Cl.9.1, Table 1 (Dimensions and Properties of Hollow Sections (Weigth))	-
Cl. 10.1, 14.1, 18.1 (Straightness)	-
Cl. 10.4, Fig 2 (Concavity, X1)	-
Cl. 10.4, Fig 2 (Convexity, X2)	-
Cl. 10.6, Fig 4 (External Corner Radius)	-
Cl. 10.7, Fig 5 (Total twist, V)	-
Cl. 15.2, Table 3 (Tensile Strength- IS 1608)	-
Cl. 15.2, Table 3 (Yield Strength- IS 1608)	-
Cl. 15.2, Table 3 (Elongation- IS 1608)	-
Cl. 14.1 (Exact Length)	-
Cl. 10.5, Fig 3 (Squareness of side)	-
Cl.7.1 (Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.7.1 (Aluminium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
7 (Micro Alloying elements(Nb+V+Ti))	-
Cl.7.1 (Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.7.1 (Aluminium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
7 (Micro Alloying elements(Nb+V+Ti))	-

-
Declaration needed for HF/ CF and Straightened (Finish or Mill ); (Chem- In case of use of hot rolled steel strip conforming to IS 10748, see status for IS 10748)

307

IS 204 : Part 2 (1992)

Tower bolts - Specification: Part 2 non - Ferrous metals (Fifth Revision)

All types

Rs.2100.00. View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (General)	-
5.2.1 Table 1 (Particulars-Barrel Tower Bolts)	-
5.2.2 Table 2 (Particulars-Skeleton Tower Bolts)	-
6.1- Table 1 (Dimension of barrel tower bolts-Minimum No. of equally Spaced holes in Barrel & Socket for wooden screw no 6)	-
6.2- Table 2 (Dimension of Skeleton Tower Bolts- Nos of Staples)	-
6.1- Table 1 (Dimension of Barrel tower bolts-1.Size 2.Length of Bolt or Barrel-(A or B) 4.Width of Barrel-C 5.Dia of Bolt-D 6.Length of Socket-E 7.Thickness of Metal of Barrel (Brass or Zink Alloy/Aluminium alloy/Sheet Brass)-F 8.Dia of bore of barrel or socket- G )	-
6.1- Table 1 (Dimension of barrel tower bolts-Minimum No. of equally Spaced holes in Barrel & Socket for wooden screw no 6)	-
7 (Finish)	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002) (Chemical composition - others - IS 504)	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002) (Chemical composition - Aluminium - IS 504)	-
4 -Table 3- i (Ref. Cl 8 , Table 1 Designation 63400 of IS 1285 : 2002) (Chemical composition - Copper - IS 504)	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002) (Chemical composition - Magnesium - IS 504)	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002) (Chemical composition - Silicon - IS 504)	-
4 -Table 3- i (Ref. Cl 8 , Table 1 Designation 63400 of IS 1285 : 2002) (Chemical composition - Iron - IS 504)	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002) (Chemical composition - Manganese - IS 504)	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002) (Chemical composition - Zinc - IS 504)	-
4 -Table 3- i (Ref. Cl 8 , Table 1 Designation 63400 of IS 1285 : 2002) (Chemical composition - Titanium - IS 504)	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002) (Chemical composition - Chromium - IS 504)	-
4 -Table 3- ii (Ref. Cl 5.1, Table 1 Designation 65032 of IS 733 : 1983) (Chemical composition - Aluminium - IS 504)	-
4 -Table 3- ii (Ref. Cl 5.1 , Table 1 Designation 65032 of IS 733 : 1983) (Chemical composition - Copper - IS 504)	-
4 -Table 3- ii (Ref. Cl 5.1 , Table 1 Designation 65032 of IS 733 : 1983) (Chemical composition - Magnesium - IS 504)	-
4 -Table 3- ii (Ref. Cl 5.1, Table 1 Designation 65032 of IS 733 : 1983) (Chemical composition - Silicon - IS 504)	-
4 -Table 3- ii (Ref. Cl 5.1 , Table 1 Designation 65032 of IS 733 : 1983) (Chemical composition - Iron - IS 504)	-
4 -Table 3- ii (Ref. Cl 5.1 , Table 1 Designation 65032 of IS 733 : 1983) (Chemical composition - Manganese - IS 504)	-
4 -Table 3- ii (Ref. Cl 5.1 , Table 1 Designation 65032 of IS 733 : 1983) (Chemical composition - Zinc - IS 504)	-
4 -Table 3- ii (Ref. Cl 5.1 , Table 1 Designation 65032 of IS 733 : 1983) (Chemical composition - Titanium and or other grain refining elements - IS 504)	-
4 -Table 3- ii (Ref. Cl 5.1, Table 1 Designation 65032 of IS 733 : 1983) (Chemical composition - Chromium - IS 504)	-
4 -Table 3- iii (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977) (Chemical composition - Copper - IS 3635:1966)	-

-
Description and type to be declared. Facility not available for Cl 4.1 Total impurities, (Al, Sn, Tl, In, Sb)

308

IS 4454 : Part 4 (2001)

Steel wires for mechanical springs: Part 4 stainless steel wire (Second Revision)

All grades/sizes

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Table 1. Cl.1.1,1.2,7.1 & 7.2 (Carbon- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
Table 1. Cl.1.1,1.2,7.1 & 7.2 (Silicon- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
Table 1. Cl.1.1,1.2,7.1 & 7.2 (Manganese- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
Table 1. Cl.1.1,1.2,7.1 & 7.2 (Phosphorous- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
Table 1. Cl.1.1,1.2,7.1 & 7.2 (Chromium- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
Table 1. Cl.1.1,1.2,7.1 & 7.2 (Nickel- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
8 (Freedom from defects)	-
9 (Dimensions & Tolerances)	-
10.1.1, Table 4 (Tensile strength)	-
10.1.1, Table 4 (Reduction in area)	-
10.2 (Wrapping test)	-
10.3 (Reverse torsion test)	-
10.4 (Cast of the wire)	-
10.5 (Bend test)	-
10.6 (Coiling test)	-
Table 1. Cl.1.1,1.2,7.1 & 7.2 (Suphur- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
Table 1. Cl.1.1,1.2,7.1 & 7.2 (Molybdenum- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-

-
Ring sample to be provided for coiling and stretching test, (Cl10.6). Grade and size to be declared Chem: Facility not available for S, Mo, Nb, V & Ti.

309

IS 16186 (2014)

Textiles - Light weight jute sacking bags for packing 50 kg foodgrains - Specification

All type

Rs.8150.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (i)The bags shall be made from single piece of 2/1 twill weave jute sacking of uniform construction with warp running along the length of the bag. )	-
4.1 (ii) The mass per square meter of sacking used in the fabric of the bag 504 g.)	-
4.2.i) ( Type of stitches Herakle )	-
4.2.ii) ( Jute twine for stitches Two strands of 3-ply )	-
4.2.iii) ( Stitches/dm 10 ± 1 )	-
4.2.iv) (Tex of jute twine [ IS 9113 (Cl.5.1.2) ] 310 tex.X 3-ply )	-
4.3.i) ( Stitches/dm 10 ± 1 )	-
4.3.ii) (Tex of jute twine )	-
4.4 (Fabric shall be hemmed with jute yarn of 310 tex )	-
4.5, Annex A (GAW)	-
4.5, Annex A (Multiple broken/missing warp(end)-Two or more contiguous, regardless of length )	-
4.5, Annex A (Multiple broken weft(pick))	-
4.5, Annex A (Cut, hole, tear or patch-Two or more warp thread ruptured at adjoining points )	-
4.5, Annex A (Float-Fabric where warp and weft yarns escape)	-
4.5, Annex A (Gap stitching-Stitching missing)	-
4.5, Annex A (Corner gap-Hole formation due to improper stitching at the corner of the bag )	-
4.5, Annex A (Mildew-Staining of fabric due to fungal or bacterial growth visible to naked eye)	-
4.1 & 5.1, Table 1 (Outside Length, cm )	-
4.1 & 5.1, Table 1 (Outside Width, cm )	-
4.1 & 5.1, Table 1 (Ends /dm-IS 9113 (Cl.8.4.2))	-
4.1 & 5.1, Table 1 (Picks/dm-IS 9113 (Cl.8.4.2))	-
4.1 & 5.1, Table 1 (Corrected Mass/Bag,g-IS 9113 (Cl.8.5.2))	-
4.1 & 5.1, Table 1 (Warpway -IS 9113 (Cl.8.6.2))	-
4.1 & 5.1, Table 1 (Weftway-IS 9113 (Cl.8.6.2))	-
4.1 & 5.1, Table 1 (Moisture Regain, Percent-IS 9113 (Cl.8.2))	-
4.1 & 5.1, Table 1 (Oil content, Percent-IS 9113 (Cl.8.5.2))	-
4.1 & 5.1, Table 1 (Average Seam Strength in N-IS 9113 (Cl.8.7))	-
4.4 (Hemming at the mouth-IS 9113 (Cl.5.1.2))	-
4 (Manufacture- IS16186)	-
4.1 (Fabric)	-
4.2 (Seam-IS 9113 (Cl.5.1.2))	-
4.3 (Union Safety Stitch-IS 9113 (Cl.5.1.2))	-
4.5 (Freedom from defects)	-
4.1 & 5.1, Table 1 (Dimension-IS 9113 (Cl.8.3.2))	-
4.1 & 5.1, Table 1 (Average Breaking Strength in N)	-
4.3 ( 310 tex.X 2-ply )	-

-
Type to be Declared. Separately Yarns(1 Ply,3 Ply) + Fabric + 2 Ply Yarn to be provided if safety stitch is present

310

IS 5517 (1993)

Steels for hardening and tempering - Speicification (Second Revision)

Please see remarks. View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2 (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2 (Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2 (Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2 (Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2 (Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2 (Aluminium IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
5 (Freedom from defects , IS 5517)	-
8,Table 6 (Hardness Test - IS 1500(Pt -1))	-
9, Table 5 (Mechanical ptoperties - IS 1608(Pt -1),IS 1598)	-
13.1&13.2&13.3 (Dimensional tolerances- IS 3739 and is 3469(Pt 1to 3); Tolerance on straightness)	-
10 (Grain Size - IS 4748)	-
11.1 (Inclusion Rating- IS 4163)	-

-
Facility not available for Additional tests (Ultrasonic test, Hot up-set for forgeability). Steel designation, delivery condition & Forging Temp to be declared.

311

IS 4224 (1972)

Specification for steel wire for staples, pins and clips (First Revision)

For all types

525 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 3.1, Table 1 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 3.1, Table 1 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 3.1, Table 1 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 3.1, Table 1 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
4 (Freedom from defects , IS 4224)	-
5 (Sizes and Tolerances - IS 4224)	-
7.1 (Tensile Test - IS 1608(Pt -1))	-
7.2 (Reverse Bend Test--IS 1716)	-
6 (Finish)	-

-
Facility not available for finish (other than galvanized)

312

IS 4223 (1975)

Steel Wire For Umbrella Ribs

all grades

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 6.1 (Sulphur- Appropriate parts of IS 228.)	-
Cl. 6.1 (Sulphur- IS 228(Part 9))	-
Cl 6.1 (Phosphorus- Appropriate parts of IS 228.)	-
Cl. 6.1 (Phosphorous- IS 228(Part 3))	-
7 (Freedom rom defects , IS 4223)	-
8,9 (Sizes and Tolerances - IS 4223)	-
10.1, Table 1 (Mechanical ptoperties - IS 1608(Pt -1))	-
10.4 ( Straightness Test - IS 4223)	-
10.5 (Deflection Test - IS 4223)	-
10.2 (Torsion Test - IS 1717)	-
10.3 (Reverse Bend Test--IS 1716)	-
12 (Rust Protection-IS 4223)	-

-
Complete

313

IS 9857 (1990)

Welding cables - Specification (First Revision)

Rs 11400/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (Conductor : Material )	-
5 (SEPARATOR)	-
6 (COVERING)	-
7 (CONDUCTOR : CONSTRUCTION )	-
8 (S E P A R A T O R)	-
9.1 (C O V E R I N G : Application )	-
9.2 (T h i c k n e s s o f C o v e r i n g)	-
9.3 (T o l e r a n c e on Thickness o f C o v e r i n g)	-
9.4 (A p p l i c a t i o n of C o v e r i n g)	-
9.5 (Colour of C o v e r i n g)	-
10.1 a) 1) (Annealing test - IS 10810: Part 1)	-
10.1 a) 2) (Conductor resistance tes - IS 10810 : Part 5)	-
10.1 c) 1) (Physical tests for covering : Tensile strength )	-
10.1 c) 1) (Physical tests for covering : Elongation at break )	-
10.1 c) 2) (Physical tests for covering - Ageing in Air oven : Tensile strength variation)	-
10.1 c) 2) (Physical tests for covering -Ageing in Air oven : Elongation at break )	-
10.1 c) 5) (Hot set test )	-
10.1 c) 5) (Permanent set )	-
11.1 (High Voltage Test ( Water Immersion Test ))	-
11.4 (Flammability Test)	-
12.1 (Manufacturer's Identification)	-
12.2 (Cable Identification)	-
12.3 (Cable Code)	-

-
Except T/S after ageing in air bomb, .oil resistance test, static flexibility test. "Declarations Required: Type of covering & Size"

314

IS 3748 (2022)

Tool Steels - Specification

All

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.4 (Shape, dimensions and tolerances)	-
7.2 (Chromium)	-
7.2 (Molybdenum)	-
7.2 (Vanadium)	-
7.2 (Tungsten)	-
7.2 (Nickel)	-
7.2 (Cobalt)	-
7.2 (Carbon)	-
7.2 (Silicon)	-
7.2 (Manganese)	-
7.2 (Phosphorus)	-
7.2 (Sulphur)	-
Annex B.7 (Non-Destructive Test)	-

-
Mech: NDT (Additional test) can be carried out for ultrasonic test only. Grade and heat treatment condition to be declared

315

IS 9295 (1983)

Specification for steel tubes for idlers for belt conveyors (First Revision)

Rs 5100/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8.1.1 Table 1 (Tensile Strength- IS 1608(1))	-
8.1.1 Table 1 (Yield Strength- IS 1608)	-
8.1.1 Table 1 (Elongation Percent- IS 1608)	-
8.2 (Drift Expansion Test- IS 2335)	-
8.3 (Flattening Test- IS 2328)	-
9.1 Table 2 (Outside Diameter)	-
9.1 Table 2 (Thickness)	-
9.1 Table 2 (Mass)	-
13.1.1 (Ovality)	-
13.1.2 (Eccentricity)	-
15.1 (Straightness)	-
16.1 (Length)	-
17.1 (Surface Protection)	-
7.1 (Sulphur- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
7.1 (Phosphorous- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
6.2 (Fin height)	-
14.0 (Workmanship)	-

-
-

316

IS 3589 (2001)

Steel pipes for water and sewage (168.3 To 2540 Mm Outside Diameter) - Specification (Third Revision)

All grades (see remarks)

Please see remarks. View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8.1 Table 2 Table 3 (Carbon Content IS 228)	-
8.1 Table 2 Table 3 (Manganese Content IS 228)	-
8.1 Table 2 Table 3 (Phosphorus Content IS 228)	-
8.1 Table 2 Table 3 (Sulphur Content IS 228)	-
11.1, Table 5. (Outside Diameter (OD))	-
11.1, Table 5. (Thickness)	-
11.1, Table 5. (Mass)	-
12.3.3 (Ovality)	-
12.5 (Strightness)	-
14.1 (Visual inspection, Appearance and Workmanship)	-
9.2.3 (Flattening Test for seamless pipes)	-
9.2.1 (Flattening test for ERW pipes )	-
9.3 (Guided Bend Test (for SAW Pipes))	-
9.1 (Tensile test-Yield Strength)	-
9.1 (Tensile test-Strength)	-
9.1 (Tensile test- Elongation)	-
11.1, Table 5. (Mass)	-
"11.1, Table 5. 12.3.3" (Avarage Outer dia (04))	-
"11.1, Table 5. 12.3.3" (Avarage Thickness (08))	-
"11.1, Table 5. 12.3.3" (Maximum Ovality (08))	-

-
Mech-Facility not available for Hydraulic & Guided bend Test and OD above 273 mm, Chem- Facility not available for Al, Nb, V, Ti (given in notes under Table-2)

317

IS 3431 (1982)

Specification for steel for the manufacture of volute helical and laminated springs for automotive suspension (Second Revision)

For all grades except tests mentioned in remarks

Rs 1800/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 2.1, 5.1 & Table 1 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 2.1, 5.1 & Table 1 (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 2.1, 5.1 & Table 1 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 2.1, 5.1 & Table 1 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 2.1, 5.1 & Table 1 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 2.1, 5.1 & Table 1 (Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
8,Table 4 (Mechanical properties - IS 3431)	-
10 (Freedom from defects)	-
12 (Straightness)	-
13, Table 5&Table 6 (Dimensions and Tolerance)	-
11 (Surface Decarburisation)	-
9, Table 2 (Cold Shearability)	-
Cl. 2.1, 5.1 & Table 1 (Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-

-
Chem- except V. Grade designation and treatment condition to be declared.

318

IS 2508 (2016)

Polyethylene films and sheets - Specification (Third Revision)

For all types except tests mentioned in remarks

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1.6a (Carbon Black Content, Annex-A)	-
5.1.6b (Ash Content, Annex-A)	-
5.1.6c (Carbon Black Dispersion, Cl.16 of IS 2530)	-
5.1.2 (Film Form)	-
5.1.3 (Odour)	-
5.1.5 (Melt Flow Index. Cl 6, 7 of IS 13360(Part-4/Section-1))	-
5.2.2 (Tolerance on Thickness, Annex-A)	-

-
Facility not available for Dirt impact, puncture test , tear resistance, density and tensile properties

319

IS 814 (2004)

Covered electrodes for manual metal arc welding of carbon and carbon manganese steel - Specification (Sixth Revision)

Rs. 17500/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1.1 (Diameter of Core Wire)	-
7.1.2 (Length of Electrodes)	-
7.2.1 (Contact End)	-
7.2.2 (Arc striking End)	-
7.3 (Concentricity of Flux covering with core wire)	-
7.4 (Defects of Core wire and Coverings)	-
6 & 8.2 (Carbon- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
6 & 8.2 (Manganese- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
6 & 8.2 (Phosphorous- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
6 & 8.2 (Sulphur- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
6 & 8.2 (Copper- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
6 & 8.2 (Alumiminium- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
6 & 8.2 (Titanium- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
CL 7.1.1 (Average length of electrodes (10))	-
CL 7.2.1 (Average length of Contact End (10))	-
CL 7.2.2 (Average length of arc striking end (10))	-
6 & 8.2 (Silicon- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
6 & 8.2 (Nickel- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
6 & 8.2 (Chromium- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
6 & 8.2 (Molybdenum- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
6 & 8.2 (Vanadium- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
6 & 8.2 (Mn+Ni+Cr+Mo+V - Relevant Parts of IS 228 or any other established instrumental/chemical method)	-

-
Facility available Only for dimension, tensile, impact and bend(if Prepared Piece supplied), Chem- Facility not available for Ti & Al for core wire and Designation/Classification reqd (Declaration for Parameters, where applicable) Prepared sample to be sent for tensile and impact.

320

IS 2507 (1975)

Specification for cold - rolled steel strips for springs (First Revision)

All Grade, Designation and Sizes (except where V is required)

Rs .6000/- Gr 1 to Gr 9 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 0.2, 4.1, 6.1, 6.2 & Table1 (Carbon- Appropriate parts of IS 228.)	-
Cl. 0.2, 4.1, 6.1, 6.2 & Table1 (Silicon- Appropriate parts of IS 228.)	-
Cl. 0.2, 4.1, 6.1, 6.2 & Table1 (Manganese- Appropriate parts of IS 228.)	-
Cl. 0.2, 4.1, 6.1, 6.2 & Table1 (Sulphur- Appropriate parts of IS 228.)	-
Cl. 0.2, 4.1, 6.1, 6.2 & Table1 (Phosphorus- Appropriate parts of IS 228.)	-
Cl. 0.2, 4.1, 6.1, 6.2 & Table1 (Chromium- Appropriate parts of IS 228.)	-
5 (FREEDOM FROM DEFECTS)	-
7 (Rolling Tolerances)	-
10 (Physical properties(optional))	-
12 (Surface condition)	-
Cl. 0.2, 4.1, 6.1, 6.2 & Table1 (Vanadium- Appropriate parts of IS 228.)	-

-
Chem: Facility not available for V. Grade, Steel designation, edge condition to be declared.

321

IS 7887 (1992)

Mild steel wire rod for general engineering purposes - Specification (First Revision)

All grades

Rs.7200/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 9 (Nominal Diameter & Out Of Shape)	-
Cl 9 (Nominal Diameter & Out Of Shape)	-
Cl 8 (Workmanship)	-
6.1 (Carbon %)	-
6.1 (Manganese %)	-
6.1 (Phosphorus %)	-
6.1 (Sulphur %)	-
6.1 (Silicon %)	-
Cl 8 (Freedom from defects)	-
Cl 9 (Avarage Outer dia (08))	-
6.1 ( Aluminium %)	-
Amendment 1 (Niobium)	-
Amendment 1 (Titanium)	-
Amendment 1 (Vanadium)	-
Amendment 1 (Micro Alloying Element (Nb+V+Ti))	-
Table 1 Note 3 (Copper)	-

-
Chem- Complete Remarks: To indicate the type of 'Killed' material.

322

IS 3195 (1992)

Steel for the manufacture of volute and helical springs (For Railway Rolling Stock) - Specification (Third Revision)

All grades

1050 Chemical View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 3, 6.1, 6.2 & Table 1 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 3, 6.1, 6.2 & Table 1 (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 3, 6.1, 6.2 & Table 1 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 3, 6.1, 6.2 & Table 1 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 3, 6.1, 6.2 & Table 1 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 3, 6.1, 6.2 & Table 1 (Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 3, 6.1, 6.2 & Table 1 (Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
7 (Hardness)	-
10 (Freedom from defects)	-
11 ( DIMENSIONS AND TOLERANCES)	-
8 (Decarburisation)	-
9 (Inclusion rating)	-
12 (Calculation of mass)	-
Cl. 3, 6.1, 6.2 & Table 1 (Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-

-
Chem- Facility not available for Vanadium.

323

IS 2879 (1998)

Mild steel for metal arc welding electrodes - Specification (Third Revision)

For all designation except tests mentioned in remarks

Testing charges are Rs.9050/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 & 9 (Diameter)	-
Cl 7 (Workmanship)	-
6 (Carbon %)	-
6 (Manganese %)	-
6 (Phosphorus %)	-
6 (Sulphur %)	-
6 ( Copper %)	-
6 ( Aluminium %)	-
6 ( Ti)	-
6 (Cr+ Mo+ Ni)	-
6 (Silicon %)	-
6 (V)	-
6 (Cr)	-
6 (Ni)	-
6 (Mo)	-

-
Chem- Facility not available for V, Ti, Al (Classification to be declared)

324

IS 2831 (2012)

Carbon steel cast billet ingots, billets, blooms and slabs for re-rolling into structural steel (Ordinary Quality) - Specification (Fourth Revision)

For all designations except tests mentioned in remarks

Rs. 4500/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
9 ( FREEDOM FROM DEFECTS)	-
11 & 12 (DIMENSIONS and Tolerances)	-
Cl. 6.1, Table 1 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, Table 1 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, Table 1 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, Table 1 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, Table 1 (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, Table 1 (Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, Table 1 (Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, Table 1 (Aluminium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Clause 6.1.1 (Carbon Equivalent (CE))	-
Cl. 6.1, Table 1 (Titanium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
10.1.a) ( Macro examination IS 11371)	-
10.1.b) ( Sulphur print tests IS 12037)	-
Cl. 6.1, Table 1 (Niobium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, Table 1 (Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, Table 1 (Titanium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Clause 6.1.1 (Carbon Equivalent (CE))	-

-
Chem- Facility not available for Micro-alloying elements & CE when Micro Alloy Elements available. To declare the type of killed material and any other information required as per Notes under Table-1

325

IS 2830 (2012)

Carbon steel cast billet ingots, billets, blooms and slabs for re-rolling into steel for general structural purposes - Specification (Third Revision)

For all designations except tests mentioned in remarks

Rs. 5250/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 9 (Workmanship)	-
Cl 11 (Length)	-
6.1 (Carbon %)	-
6.1 (Manganese %)	-
6.1 (Phosphorus %)	-
6.1 (Sulphur %)	-
6.1 (Silicon %)	-
6.1 ( Copper %)	-
Clause 6, Table 1 Note : 1 (Carbon Equivalent)	-
Clause 6, Table 1 Note : 9 (S+P)	-
6.1 ( Nitrogen%)	-
6.1 ( Ti)	-
10 (b) (Sulphur Print Test - IS:12037)	-
10.1 (a) (Macro-examination)	-
6.1 ( Aluminium %)	-
6 (Micro alloying elements)	-
Cl 6.1 (Nb+V+Ti)	-
6.1 (Ni)	-
6.1 (Cr)	-
6.1 (Mo)	-

-
To indicate the type of 'Killed' material, if applicable. Also to indicate any other information as per Note under Table-1.

326

IS 8737 (2017)

Valve fittings for use with liquefied petroleum gas (LPG) cylinders for more than 5 litre water capacity - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2.1Sl.No.i (Copper)	-
4.2.1Sl.No.ii (Lead)	-
4.2.1Sl.No.iii (Iron)	-
4.2.1Sl.No.iv (Manganese)	-
4.2.1Sl.No.vi (Zinc)	-
4.3.1a (Tensile Strength-IS 1608)	-
4.3.1b (Elongation-IS 1608)	-
4.4 (Izod impact strength-IS 1598)	-
7.1 (Design Requirements)	-
7.2 (Design Requirements)	-
7.3 (Design Requirements)	-
7.4 (Design Requirements)	-
7.5 (Design Requirements)	-
7.6 (Design Requirements)	-
7.9 (Design Requirements)	-
7.10 (The minimum finished wall thickness at any portion of the valve shall not be less than 2.5 mm)	-
7.10.1 (In case of self-closing valves having outlet connections of 22 mm diameter or less the minimum finished wall thickness at the neck portion of the valve outlet shall not be less than 1.9 mm)	-
7.11 (The valve shall not be provided with safety relief device)	-

-
Facility not available for hydrostatic test, thread measurement, pneumatic, cycle test, Chem- 'Others' as elements not specified in ISS. Size/variety to be declared.

327

IS 281 (2009)

Mild steel sliding door bolts for use with padlocks - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 (DIMENSIONS AND TOLERANCES-A)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-B)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-C)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-D)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-E)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-F)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-G)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-H)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-J)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-T)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-DIMENSIONS AND TOLERANCES-No. of Screw on Staple or Clip to accommodate Wood Screw N0 (IS 451))	-
6-Table 1 (DIMENSIONS AND TOLERANCES-No. of Rivets on bolts plates)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-No. of Rivets on Socket)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-No. of Screw holes on Staple)	-
8.1 (FINISH-Sliding Bolts, Plate Type)	-

-
Chem- Facility not available for Cl 5, Nb, V, Al, Ti, B. Type to be declared

328

IS 5484 (1997)

Ec grade aluminium rod produced by continuous casting and rolling - Specification (Second Revision)

complete

Rs.3240.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
10.1 (Diameter - IS:5484)	-
8-Table-1 (Tensile Strength - IS:1608)	-
9 (Resistyvity at 20 degree C -IS:398(P-2))	-
11.1 (Joint- IS:5484)	-
12.1 (Freedom from defects- IS:5484)	-
12.2 (Finish - IS:5484)	-
5.1 -Table-1, ii (Silicon - IS:504)	-
5.1 -Table-1, iii (Iron - IS:504)	-
5.1 -Table-1, iv (Copper - IS:504)	-
5.1 -Table-1, vi (Manganese - IS:504)	-
5.1 -Table-1, vi (Chromium - IS:504)	-
5.1 -Table-1, i (Aluminium- IS:504)	-
5.1 -Table-1, v (Titanium+ Vanadium - IS:504)	-
8-Table-1 (Tensile Strength - IS:1608)	-

-
Test facility is not available for Aluminium, , vanadium & Zirconium. Tensile strength range to be declared.

329

IS 8952 (1995)

Steel ingots, blooms and billets for production of mild steel wire rods for general engineering purposes - Specification (First Revision)

All grades except for the tests mentioned in remarks

4840 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4,7.1 Table 1 (Carbon- IS 228 or any other established instrumental /Chemical method)	-
4,7.1 Table 1 (Manganese- IS 228 or any other established instrumental /Chemical method)	-
4,7.1 Table 1 (Sulphur- IS 228 or any other established instrumental /Chemical method)	-
4,7.1 Table 1 (Phosphorous- IS 228 or any other established instrumental /Chemical method)	-
4,7.1 Table 1 (Silicon- IS 228 or any other established instrumental /Chemical method)	-
9 (Freedom from defects , IS 8952)	-
10 ,a) (Macro examination - IS 11371)	-
11,12 (Dimensions & Tolerance)	-
Clause 4,7.1 (Aluminium)	-
Clause 4,7.1 (Titanium)	-
9 (Freedom from defects , IS 8952)	-
10 ,a) (Macro examination - IS 11371)	-
11,12 (Dimensions & Tolerance)	-
10 ,c) (Inclusion content - IS 4163)	-
4,7.1 Table 1 (Nb- IS 228 or any other established instrumental /Chemical method)	-
Clause 4,7.1 (Vanadium)	-

-
Chemical- Except Cu. Grades to be declared

330

IS 963 (1958)

Specification for chrome molybdenum steel bars and rods for aircraft purposes

All grades except for the tests mentioned in remarks

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 (Carbon- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
6.1 (Silicon- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
6.1 (Manganese- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
6.1 (Suphur- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
6.1 (Phosphorous- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
6.1 (Chromium- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
6.1 (Nickel- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
6.1 (Molybdenum- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
4 (Freedom from defects)	-
7.5 (Hardness)	-
7.6.2 (i) Yield stess/.2% Proof stress, Mpa)	-
7.6.2 (ii)Ultimate Tensile Strength, Mpa)	-
7.6.2 (iii)Elongation, %)	-
7.6.2 (iv) Reduction in area)	-
7.2 (Grain Size)	-
7.3 (Macro examination)	-
7.4 (Decarburisation)	-
7.1 (Hardenability)	-
9 (Rolling Tolerances)	-

-
-

Bureau of Indian Standards

The National Standards Body of India

BIS, Eastern Regional Laboratory (ERL)

(1) Annex Building & Sample-Cell: Bureau of Indian Standards, P-230, CIT Scheme, VII- M, Block-W,Kankurgachi,Kolkata-700054 (2) Main building: 1/14, CIT Scheme VII M, VIP Road, Kankurgachi,Kolkata-700054, Kolkata, Kolkata, West Bengal, 700054

- sample.erol@bis.gov.in

Scope List