BIS - LIMS (Laboratory Information Management System)

BIS, Eastern Regional Laboratory (ERL)

(1) Annex Building & Sample-Cell: Bureau of Indian Standards, P-230, CIT Scheme, VII- M, Block-W,Kankurgachi,Kolkata-700054 (2) Main building: 1/14, CIT Scheme VII M, VIP Road, Kankurgachi,Kolkata-700054, Kolkata, Kolkata, West Bengal, 700054

- sample.erol@bis.gov.in

Scope List

Reset

370 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

271

IS 1239 : Part 1 (2004)

Steel tubes, tubulars and other wrought steel fittings - Specification: Part 1 steel tubes (Sixth Revision)

For all designation except tests mentioned in remarks

Rs. 9200/- Excluding test on joints View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (Outer Diameter, Thickness & Mass)	-
Cl 14 (Tensile Test, Flattening Test & Bend Test)	-
Cl 14 (Tensile Test, Flattening Test & Bend Test)	-
Cl 14 (Tensile Test, Flattening Test & Bend Test)	-
Cl 15 (Workmanship)	-
Cl 14 (Tensile Test, Flattening Test & Bend Test)	-
7, 6.1.1 (CARBON)	-
7, 6.1.1 (SULPHUR)	-
7, 6.1.1 (PHOSPHURS)	-
7, 6.1.1 (MANGANESE)	-
7, 6.1.1 (SILICON)	-

-
Mech: Except Hydrostatic test and thread Chem: except Al,B,Nb,V,Ti,Ca 1m x1 No ( plus another 1.8 m pc for bend test up to 50 mm NB) + 50 g drilling + 4 pcsx10 cm

272

IS 11169 : Part 1 (1984)

Specification for steels for cold heading/cold extrusion applications: Part 1 wrought carbon and low alloy steels

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 6 (Diameter & Out Of Roundness)	-
TABLE-1,2,3 (Clause 4,4.1,4.2,4.3) ( CARBON)	-
TABLE-1,2,3 (Clause 4,4.1,4.2,4.3) (SULPHUR)	-
TABLE-1,2,3 (Clause 4,4.1,4.2,4.3) (PHOSPHURS)	-
TABLE-1,2,3 (Clause 4,4.1,4.2,4.3) (MANGANESE)	-
TABLE-1,2,3 (Clause 4,4.1,4.2,4.3) (SILICON)	-
TABLE-1,2,3 (Clause 4,4.1,4.2,4.3) (Nickel)	-
TABLE-1,2,3 (Clause 4,4.1,4.2,4.3) (Chromium)	-

-
1.5 m (Prepared sample should be provided for hardenability test) Excluding Cl 12.1 Microscopic Inclusions, Cl 15 Decarburization, 14.1.1 Macroetch test, 14.1.3.1Eddy current/magnetic particle test ,Cl.7.1, C(<0.05%)V, Sn, B, Al

273

IS 14885 (2001)

Polyethylene pipes for the supply of gaseous fuels - Specification

Rs. 5500/- View breakup
Rs. 5500/- (excluding Hydraulic characteristics, Density, OIT, Resistance to weathering and squeeze-off)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.4 (Colour)	-
6.1, Table-3 (Nominal Outside Diameter of Pipes , Cl 6.3.1)	-
6.1, Table-3 (Ovality Pipe, Cl 6.3.2)	-
6.2.1, Table-4 (Minimum Wall Thickness, Cl.6.3, Cl.6.2.1.1, Table-5)	-
8.2 (Reversion Test. Annex-C)	-
8.4 (Melt Flow Rate (MFR), IS 2530)	-
8.6 & Table-2 (Volatile Content: Annex-H of IS 14885)	-
8.7 (Tensile yield strength, Annex-J)	-
8.6 & Table-2 (Volatile Content: Annex-H of IS 14885)	-
7, Table-6 (Maximmn Out of Square of Each Pipe End)	-
8.7 (Elongation at break, Annex-J)	-

-
Facility not available for water content and Thermal stability, water content and thermal stability.

274

IS 14887 (2014)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg food grains – Specification (first revision)

19750 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2 (Unlaminated Fabric Mass )	-
3.2 (Tapes – Width and Thickness ( IS 6192/IS 11197))	-
3.2 (Tapes – Elongation at point of rupture (IS 6192/IS 11197))	-
3.2 (Tapes – Dimensional stability (PP) (IS 11197))	-
3.3.1 (Bottom seam (IS 10789))	-
4.2 and Table 1 ii (Dimensions )	-
5.2 and Table 1 iii (Ends per dm )	-
5.2 and Table 1 iv (Picks per dm )	-
4.2 and Table 1 v (Mass of sack )	-
4.2 and Table 1 vi (Average breaking strength of fabric )	-
4.2 and Table 1 vi (Breaking strength of bottom seam )	-
4.2 and Table 1 viii (Elongation at break of fabric )	-
4.2 and Table 1 x (Ash content )	-
3.2 (Unlaminated Fabric Mass )	-
3.2 (Tapes – Width and Thickness ( IS 6192/IS 11197))	-
3.2 (Tapes – Elongation at point of rupture (IS 6192/IS 11197))	-
3.2 (Tapes – Dimensional stability (PP) (IS 11197))	-
3.3.1 (Bottom seam (IS 10789))	-
4.2 and Table 1 ii (Dimensions )	-
5.2 and Table 1 iii (Ends per dm )	-
5.2 and Table 1 iv (Picks per dm )	-
4.2 and Table 1 v (Mass of sack )	-
4.2 and Table 1 vi (Average breaking strength of fabric )	-
4.2 and Table 1 vi (Breaking strength of bottom seam )	-
4.2 and Table 1 viii (Elongation at break of fabric )	-
4.2 and Table 1 x (Ash content )	-
4.2 and Table 1 x (Ash content )	-
4.2 and Table 1 ix (Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-

-
Complete

275

IS 778 (1984)

Specification for 2010 copper alloy gate, globe and check valves for waterworks purposes (Fourth Revision)

For all classes except tests mentioned in remarks

Rs 4500/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3 (Nominal Sizes )	-
4 (Classification )	-
5 (Types)	-
7.1 (Valve Bodie - IS 778)	-
7.1.1 (Body End Ports -IS 778)	-
7.1.2 (Water-Way Area - IS 778)	-
7.1.3 (Screwed Body End -IS 778)	-
7.1.3.1-Table2 (length of threaded portion in screwed end valves - IS 778)	-
7.1.3.1 (Screwed Body End -IS 778)	-
7.1.5 (Wedge and Disc Guides in the Bodies of Gate Valves - IS 778)	-
7.2.1 (Bonnets - IS 778)	-
7.2.1.1 (Bonnets - IS 778)	-
7.2.1.2 (number of engaged threads - IS 778)	-
7.2.1.2 (pitch of threads - IS 778)	-
7.2.1.3 (Bonnets - IS 778)	-
7.3 (Stuffing Box - IS 778)	-
7.4 (Gland - IS 778)	-
7.4.1 (Gland nut - IS 778)	-
7.6.1 (Stem - IS 778)	-
7.6.2 (Threads of Stem - IS 778)	-
7.6.3 (actuating threads - IS 778)	-
7.6.4 (Length of Stem - IS 778)	-
7.6.5 (Upper end of Stem - IS 778)	-
7.6.7 (Non-rising Stem - IS 778)	-
7.6.6 (Rising Stem - IS 778)	-
7.7.1 (Wedge-IS 778)	-
7.7.2 (Wedge-IS 778)	-
7.7.3 (Double disc - IS 778)	-
7.7.3.1 (Spreading assembly - IS 778)	-
7.7.3.2 (Disc - IS 778)	-
7.10.1 (Body Seats - IS 778)	-
7.10.1 (Seat ring - IS 778)	-
7.11 (Handwheel - IS 778)	-
7.11 (Handwheel - IS 778)	-
8.1- Table 4 (Thickness of Body and Bonnet- IS 778)	-
8.2 - Table 5 (Flat to Flat size -IS 778 )	-
8.3 - Table 6 (Width of end - IS 778)	-
8.4 - Table 7 (Stem Diameters - IS 778)	-
8.5 - Table 8 (Size of packing space - IS 778)	-
8.5 - Table 8 (Depth of stuffing box - IS 778)	-
8.5 - Table 8 (Dia of stuffing box - IS 778)	-
8.6- Table 9 to Table 12 (End to end/ centre to ends/ Face to face/Centre to face dimension )	-
6- Table 1-i) (Brass(Body)-Cl 7 and table 1 of IS 1264)	-

-
Facility not available for hydraulic test & Thread measurement

276

IS 10124 : Part 2 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 2 specific requirements for sockets (Second Revision)

For all classes except for the tests mentioned in remarks

Rs.1800/ View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2.1, Table-1, Fig-1 (Minimum wall thickness for working pressure)	-
3.2.1, Table-1, Fig-1 (Nominal size)	-
Clause 3.2.2, and Fig. 2. (B)	-
10.3 of IS 4985 & Cl. 3.1 of IS 12235(P-4) (Effect on water: Lead (First Extraction))	-
10.3 of IS 4985 & Cl. 3.1 of IS 12235(P-4) (Effect on water: Lead (Third Extraction))	-
10.3 of IS 4985 & Cl. 3.1 of IS 12235(P-10) (Effect on water:Dialkyl tin C4 and higher homologues measured as tin (third extraction))	-
10.3 of IS 4985 & Cl. 3.2 of IS 12235(P-4) (Effect on water: Cadmium (all three extracts))	-
10.3 of IS 4985 & Cl. 3.2 of IS 12235(P-4) (Effect on water: Mercury (all three extracts))	-

-
Facility not available for Short term hydraulic test. Chemical: All except Effect on Water which is for Pipes above 60 mm Nominal dia and except for the requirement of 'Other Toxic Substances such a di-n-octyl Tin -s-s bis iso-octyl mercapto acetate' and 'butyl stearate';

277

IS 6003 (2010)

Indented Wire For--Prestressed Concrete ”

Rs.4110/- excl. relaxation test View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5.1 (Diameter)	-
Cl 6.1.2 (Weight)	-
Cl 7.1 (Tensile Test On UTM)	-
Cl 7.2 (Tensile Test On UTM)	-
4.1.1 (Phosphorus %)	-
4.1.1 (Phosphorus %)	-
4.1.1 (Sulphur %)	-
4.1.1 (Sulphur %)	-
"Cl 5.1 Cl 6.1.2" (Avarage Outer dia (06))	-
"Cl 5.1 Cl 6.1.2" (Maximum Ovality (06))	-

-
Facility not available for Relaxation test

278

IS 1341 (2018)

Steel Butt Hinges - Specification (Sixth Revision)

For all types except test mentioned in remarks

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 Tables 2 to 9 (2) (Size of Hinge)	-
5.1 Tables 2 to 9 (3) (Length A)	-
5.1 Tables 2 to 9 (4) (Breadth B)	-
5.1 Tables 2 to 9 (4) (Breadth B1)	-
5.1 Tables 2 to 9 (4) (Breadth B2)	-
5.1 Tables 2 to 9 (5) (Thickness of Flap C)	-
5.1 Tables 2 to 9 (6) (Diameter of Hinge Pin D)	-
5.1 Tables 2 to 9 (7) (Number of Knuckles)	-
5.1 Tables 2 to 9 (8) (Number of Screw Holes)	-
5.1 Tables 2 to 9 (9) (Holes for Screw No.)	-
6.1 (General)	-
6.1 (General)	-
6.2.1 (Knuckles)	-
6.3 (Pins)	-
6.4.2 (X)	-
6.4.2 (Y)	-
6.4.2 (Z)	-
7 (Finish)	-
Clause 4 Table 1 (Carbon ( Flap))	-
Clause 4 Table 1 (Sulphur ( Flap))	-
Clause 4 Table 1 (Phosphorus ( Flap))	-
Clause 4 Table 1 (Manganese ( Flap))	-
Clause 4 Table 1 (Nitrogen ( Flap))	-
Clause 4 Table 1 (Carbon ( Pin))	-
Clause 4 Table 1 (Sulphur ( Pin))	-
Clause 4 Table 1 (Phosphorus ( Pin))	-
Clause 4 Table 1 (Manganese ( Pin))	-
Clause 4 Table 1 (Nitrogen ( Flap))	-
TABLE-1 (Clause-4) ( CARBON)	-
TABLE-1 (Clause-4) (SULPHUR)	-
TABLE-1 (Clause-4) (PHOSPHURS)	-
TABLE-1 (Clause-4) (MANGANESE)	-
TABLE-1 (Clause-4) (SILICON)	-
TABLE-1 (Clause-4) (Chromium)	-
TABLE-1 (Clause-4) (VANADIUM)	-
TABLE-1 (Clause-4) (Nickel)	-
TABLE-1 (Clause-4) (NIOBIUM)	-
TABLE-1 (Clause-4) (TITANIUM)	-
TABLE-1 (Clause-4) (Molybdenum)	-

-
Chem: Except Al,B,Ca,Cu

279

IS 1161 (2014)

Steel tubes for structural purposes - Specification (Fifth Revision)

For all grades except test mentioned in remarks

5725 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 6 (Outer Diameter, Thickness & Mass)	-
Cl 7 (Workmanship)	-
Cl 11 (Tensile Test, Flattening Test & Cold Bend Test)	-
Cl 11 (Tensile Test, Flattening Test & Cold Bend Test)	-
Cl 9 (Workmanship)	-
Cl 13 (Workmanship)	-
Cl 11 (Tensile Test, Flattening Test & Cold Bend Test)	-
Cl 6 (Outer Diameter, Thickness & Mass)	-
Cl 9 (Workmanship)	-
8 AND AS PER IS 4736 (UNIFORMITY OF ZINC COATING)	-
8 AND AS PER IS 4736 (MASS OF ZINC COATING)	-
Clause - 5.1, Table-3 (SULPHUR)	-
Clause - 5.1, Table-3 (PHOSPHURS)	-
Clause - 5.1, Table-3 (MANGANESE)	-
Clause - 5.1, Table-3 (NITROGEN)	-
Clause - 5.1, Table-3 (SILICON)	-
5 AND AS PER IS 10748 (COPPER)	-
5 AND AS PER IS 10748 (CARBON EQUIVALENT)	-
CL 06 (Minimum Outer dia (04))	-
CL 06 (Maximum Outer dia (04))	-
CL 06 (" Minimum Thickness (08)")	-
CL 06 (Maximum Thickness (08))	-
Clause - 5.1, Table-3 ( ALUMINIUM)	-
5 AND AS PER IS 10748 (CARBON)	-
Cl.5,8.1,8.2 (Chromium)	-
Cl.5,8.1,8.2 (Boron(B))	-
Cl.5,8.1,8.2 (Titanium(Ti))	-
Cl.5,8.1,8.2 (Niobium(Nb))	-
Cl.5,8.1,8.2 (Vanadium(V))	-
Cl.5,8.1,8.2 (Nb+Ti+V)	-
Cl.5,8.1,8.2 (Nickel)	-
Cl.5,8.1,8.2 (Molybdenum)	-

-
Requirment: Material of manufacture to be declared, 1 m X 1 No (plus another 1.8 m pc for bend test up to 50 mm NB),,Mech - For above NB 250 mm, prepared Mechanical test pc to be sent ;

280

IS 5290 (1993)

Landing valves - Specification (Third Revision)

For all types except test mentioned in remarks

Rs 4500/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5, 5.1 (a) fig-1, type A (Types AND DIMENSIONS)	-
5, 5.1 (b) fig-2, type B (Types AND DIMENSIONS)	-
5.2 (Types AND DIMENSIONS)	-
6, 6.1 (Finish)	-
6, 6.2 (Finish)	-

-
Facility not available for performance test, Al, Ti

281

IS 1759 (1986)

Specification for powrahs (Second Revision)

For all types

Rs.2100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.1 (Shapes)	-
2.1 (Dimensions of Powrah-A)	-
2.1 (Dimensions of Powrah-B)	-
2.1 (Dimensions of Powrah-C)	-
2.1 (Dimensions of Powrah-D)	-
2.1 (Dimensions of Powrah-E)	-
2.1 (Dimensions of Powrah-F)	-
2.1 (Dimensions of Powrah-G)	-
2 Fig 11 (Dimensions of Eye-H)	-
2 Fig 11 (Dimensions of Eye-J)	-
2 Fig 11 (Dimensions of Eye-K)	-
2 Fig 11 (Dimensions of Eye-L)	-
2 Fig 11 (Dimensions of Eye-M)	-
2.3 (Blade thickness)	-
4 (Mass)	-
5.2 (Hardness)	-
6.1 (Workmanship & Finish)	-
7.1 (Preservative Treatment)	-
10.1 (Drop test)	-
6.1 (Workmanship & Finish)	-
6.1 (Workmanship & Finish)	-
6.1 (Workmanship & Finish)	-
6.2 (Workmanship & Finish)	-
7.2 (Preservative Treatment)	-

-
-

282

IS 6240 (2008)

Hot rolled steel plate (Up To 6 Mm) sheet and strip for the manufacture of low pressure liquefiable gas cylinders (Fourth Revision)

For all grades except test mentioned in remarks

Rs.9710/- excluding Erichsen cupping test. View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 7 (UTM)	-
Cl 8 (Press)	-
Cl 9 (Strainage Embrittlement)	-
Cl 10 (Erichsen Cupping)	-
Cl 13 (Length, Width & Thickness)	-
6.1 (Carbon %)	-
6.1 (Silicon %)	-
6.1 (Manganese %)	-
6.1 (Phosphorus %)	-
6.1 (Sulphur %)	-
6.1 ( Aluminium %)	-
6 (Niobium as Nb)	-
6 (Titanium as Ti)	-
6 (Vanadium as V)	-
6.1 (Nitrogen%)	-

-
Chem- Sheet Thickness Should be Greater than 0.5 mm Requirement: Grade to be declared

283

IS 7494 (1981)

Specification for steel for valves for internal combustion engines (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 6.1, 6.2, 6.3, & Table 1 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, 6.2, 6.3, & Table 1 (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, 6.2, 6.3, & Table 1 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, 6.2, 6.3, & Table 1 (Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, 6.2, 6.3, & Table 1 (Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, 6.2, 6.3, & Table 1 (Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, 6.2, 6.3, & Table 1 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, 6.2, 6.3, & Table 1 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, 6.2, 6.3, & Table 1 (Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, 6.2, 6.3, & Table 1 (Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
5 (Freedom from defects)	-
8 (Hardness , max-IS 1500 )	-
9.1, Table 5 (Yield Strength, Mpa)	-
9.1, Table 5 (Tensile Strength, Mpa)	-
9.1, Table 5 (Elongation, %)	-
9.1, Table 5 (Reduction in area, Percent)	-
12 (Dimensions and Tolerances, mm)	-
Cl. 6.1, 6.2, 6.3, & Table 1 (Tungsten- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, 6.2, 6.3, & Table 1 (Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-

-
Chem-Facility not available for Nb,Ti,Mo(>1.5%) (50 gm drillings to be provided) Mech- except Tensile at elevated temp

284

IS 7452 (1990)

Hot rolled steel sections for doors, windows and ventilators - Specification

Rs 1800/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
cl 6 (Dimensions)	-
cl 7 (MASS AND MASS TOLERANCE)	-
cl 8 (SURFACE FINISH)	-
cl 9 (BEND TEST)	-
5.1 (Carbon- IS 228(Part 1))	-
5.1 (Sulphur- IS 228(Part 9))	-
5.1 (Phosphorous- IS 228(Part 3))	-
5.1 (Manganese- IS 228(Part 2))	-
5.1 (Silicon- IS 228(Part 8))	-
5.1 (Nitrogen-IS 228(P-19))	-
5.1 (Copper- IS 228(P-15))	-

-
Chem: Excluding C(<0.05), Mo, Ti, Al, B, V Mech: excluding Critical Dimensions

285

IS 8041 (1990)

Rapid hardening portland cement - Specific4tion (Second Revision)

Please see remarks View breakup
Testing charges for the product are: Including Transverse Strength (optional test) test 9,100.00 Excluding Transverse Strength (optional test) test 7,900.00 -Testing charges for only chemical test report: 4,300.00 -Testing charges for only physical test report including optional tests: 4,800.00 -Testing charges for only physical test report excluding optional tests: 3,600.00

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 - Table - 1 i (Ratio of percentage of lime to percentages of silica, alumina and iron oxide - Cl 4 of IS 4032:1985)	-
5.1 - Table - 1 i (Ratio of percentage of lime to percentages of silica, alumina and iron oxide - Cl 4 of IS 4032:1985)	-
5.1 - Table - 1 ii (Ratio of percentage of alumina to that of iron oxide - Cl 4 of IS 4032:1985)	-
5.1 - Table - 1 ii (Ratio of percentage of alumina to that of iron oxide - Cl 4 of IS 4032:1985)	-
5.1 - Table - 1 iii (Insoluble residue - Cl 4.10 of IS 4032:1985)	-
5.1 - Table - 1 iii (Insoluble residue - Cl 4.10 of IS 4032:1985)	-
5.1 - Table - 1 iv (Magnesia - Cl 4.8 of IS 4032:1985)	-
5.1 - Table - 1 iv (Magnesia - Cl 4.8 of IS 4032:1985)	-
5.1 - Table - 1 v (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-
5.1 - Table - 1 v (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-
5.1 - Table - 1 vi (Total loss on ignition - Cl 4.2 of IS 4032:1985)	-
5.1 - Table - 1 vi (Total loss on ignition - Cl 4.2 of IS 4032:1985)	-
6.1 (Fineness 4031 Part 2)	-
6.2.1 (Expansion by Le Chatelier- 4031 Part 3)	-
6.2.1.1 (Expansion after aeration - 4031 Part 3)	-
6.2.1 (Expansion by Autoclave- 4031 Part 3)	-
6.2.1.1 (Expansion after aeration- 4031 Part 3)	-
6.3 a) (Setting Time Initial- 4031 Part 5)	-
6.3 b) (Setting Time Final- 4031 Part 5)	-
6.4 a) (Compressive Strength At 24 hrs ± 30 minutes - IS 4031 Part 6)	-
6.4 b) (Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-
6.5 (Transverse Strength - IS 4031 Part 8 (Optional))	-

-
Excluding transverse test(Optional)

286

IS 15961 (2012)

Hot dip aluminium - Zinc alloy metallic coated steel strip and sheet (Plain)

For all grades

Rs.4990/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 9 & Table 2 (Workmanship)	-
Cl 10 (Coating Adhesion )	-
Cl 11 (Workmanship)	-
Cl 12 (Weight)	-
Cl 13 (Length, Width, Thickness, Camber, Deviation From Squareness & Deviation From Flatness)	-
4, 5 (CARBON)	-
Cl-13.3 (Width Tolerance)	-
Cl-13.4 (Thickness Tolerance)	-

-
Mech: Complete Chemical: Except Al, Ti, Nb and V

287

IS 6006 (2014)

Uncoated stress relieved strand for prestressed concrete - Specification (Second Revision)

For all designation except tests mentioned in remarks

Rs 4035/- Excluding Proof Stress and Relaxation Test View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 4 (Length )	-
Cl 4.5 (Workmanship)	-
Cl 4.5 (Workmanship)	-
Cl 4.5 (Workmanship)	-
Cl 4.5 (Workmanship)	-
Cl 5, Table 1 (Diameter)	-
Cl 5, Table 1 (Diameter)	-
Cl 5, Table 1 (Weight)	-
Cl 7.1 (Tensile Test On UTM)	-
Cl 7 (Tensile Test On UTM)	-
4.1.2 (sulphur)	-
4.1.2 (phosphorus)	-
Cl 5.1 (Average Diameter (08))	-
CL 5.1 (Average Nominal cross-sectional area (09))	-

-
Facility not available for Stress Relaxation test

288

IS 8042 (2015)

White portland cement - Specification (Third Revision)

Rs 12050/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5 - Table - 1 i (Ratio of percentage of lime to percentages of silica, alumina and iron oxide - Cl 4 of IS 4032:1985)	-
5 - Table - 1 i (Ratio of percentage of lime to percentages of silica, alumina and iron oxide - Cl 4 of IS 4032:1985)	-
5 - Table - 1 ii (Iron oxide - Cl 4.5 of IS 4032:1985)	-
5 - Table - 1 ii (Iron oxide - Cl 4.5 of IS 4032:1985)	-
5 - Table - 1 iii (Insoluble residue - Cl 4.10 of IS 4032:1985)	-
5 - Table - 1 iii (Insoluble residue - Cl 4.10 of IS 4032:1985)	-
5 - Table - 1 iv (Magnesia - Cl 4.8 of IS 4032:1985)	-
5 - Table - 1 iv (Magnesia - Cl 4.8 of IS 4032:1985)	-
5 - Table - 1 v (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-
5 - Table - 1 v (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-
5 - Table - 1 vi (Loss on ignition - Cl 4.2 of IS 4032:1985)	-
5 - Table - 1 vi (Loss on ignition - Cl 4.2 of IS 4032:1985)	-
5 - Table - 1 vii (Chloride content - Cl 4.13 of IS 4032:1985)	-
5 - Table - 1 vii (Chloride content - Cl 4.13 of IS 4032:1985)	-
6 -Table 2- i (Fineness 4031 Part 2)	-
6 -Table 2- ii- a (Expansion by Le Chatelier- 4031 Part 3)	-
6 -Table 2- ii- a (Expansion after aeration - 4031 Part 3)	-
6 -Table 2- ii- b (Expansion by Autoclave- 4031 Part 3)	-
6-Table 2- ii- b (Expansion after aeration- 4031 Part 3)	-
6 -Table 2- iii- a (Setting Time Initial- 4031 Part 5)	-
6 -Table 2-iii- b (Setting Time Final- 4031 Part 5)	-
6 -Table 2- iv- a (Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-
6 -Table 2- iv- b (Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-
6 -Table 2- iv- c (Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-
6 -Table 2- v (Transverse Strength - IS 4031 Part 8 (Optional))	-
6 -Table 2- vi (Degree of whiteness-Annex B)	-

-
Facility not available for transverse test(Optional)

289

IS 8052 (2006)

Steel ingots,billets and blooms for the production of springs, rivets and screws for general engineering applications - Specification (Second Revision)

All grades except for the tests mentioned in remarks

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause No. 6.1 Table No. 1 (Carbon)	-
Clause No. 6.1 Table No. 1 (Silicon)	-
Clause No. 6.1 Table No. 1 (Manganese)	-
Clause No. 6.1 Table No. 1 (Sulphur)	-
Clause No. 6.1 Table No. 1 (Phosphorus)	-
Clause No. 6.1 Table No. 1 (Chromium)	-
Clause No. 6.1 Table No. 1 (Molybdenum)	-
8 (Freedom from defects , IS 8052)	-
10,11 (Dimensions & Tolerances)	-
9,a) (Macro examination - IS 11371)	-
9,d) (Inclusion content - IS 4163)	-
6.1 Table 1 (Vanadium- IS 228 or any other established instrumental /Chemical method)	-

-
Remarks: Grade designation to be declared

290

IS 6909 (1990)

Supersulphated cement ? specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (Insoluble residue - Cl 4.10 of IS 4032:1985)	-
5.1 (Magnesium Oxide - Cl 4.8 of IS 4032:1985)	-
5.1 (Sulphuric anhydride - Cl 4.9 of IS 4032:1985)	-
5.1 (Sulphide sulphur - Cl 6.12 of IS 4032:1985)	-
6.1 (Fineness 4031 Part 2)	-
6.2 (Soundness (cold expansion) by Le Chatelier- 4031 Part 3)	-
6.3 a) (Setting Time Initial- 4031 Part 5)	-
6.3 b) (Setting Time Final- 4031 Part 5)	-
6.4 a) (Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-
6.4 b) (Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-
6.4 c) (Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-
5.1 (Chloride content)	-
5.1 (Insoluble residue - Cl 4.10 of IS 4032:1985)	-
5.1 (Magnesium Oxide - Cl 4.8 of IS 4032:1985)	-
5.1 (Sulphuric anhydride - Cl 4.9 of IS 4032:1985)	-
5.1 (Sulphide sulphur - Cl 6.12 of IS 4032:1985)	-
6.5 (Transverse Strength - IS 4031 Part 8 (Optional))	-

-
mech- 8 kg, Chem: 1kg Excluding except transverse test(Optional)

291

IS 1660 (2009)

Wrought aluminium utensils - Specification (First Revision)

Rs 6760/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
0.5 (Fabrication)	-
6.1 & Table 1 ( i) Name of Utensil )	-
6.1 & Table 1 (ii) Shape of Utensil)	-
6.1 & Table 1 (Inside dia, Φ D mm Not declared )	-
6.1 & Table 1 (Outside dia Ф NA)	-
6.1 & Table 1 (Height NA)	-
6.1 & Table 1 (Capacity, l NA)	-
6.1 ( Minimum sheet thickness for nominal size )	-
7.1 (HANDLES ,When fitted shall be of aluminium, stainless steel or of other suitable fire resistance material These shall be fastened to the utensils by tightly drawn aluminium or stainless steel rivets, by welding, by screwing to cast bosses or by riveting between flange at the end of the handles. Handles shall be so shaped and positioned to facilitate the carrying and handling of the utensils in normal use )	-
7.2 (Handles shall be sufficiently strong to support a mass in the utensils equivalent to three times the mass of the water capacity of the utensils in the position of normal use without visible permanent deformation of the handle or utensil)	-
8.1 (The utensils shall be clean reasonably free from distortion, dents, wrinkles, wavy surface, burrs, scratches, pitting and deep tool marks and other surface defects)	-
8.2 (The design of the utensils shall be such that it is easy to clean and prevent accumulation of dirt)	-
8.4.1.2 ( Finish of the coating: The coating shall be smooth continuous and uniform in appearance, and shall be adherent. It shall be free from powdery areas, loose films and discontinuities, such as breaks and scratches. The size and number of contact marks shall be minimum consistent with good practice.)	-
8.4.2 (A coating of thickness 25 to 100 microns is generally required)	-
8.4.3 (Abrasion Resistance When the coating surface is rubbed two or three times with emery paper with emery conforming to grit number 180 using medium finger pressure, it shall not abrade the surface but shall skid over the surface showing not more than a trace of whitening of the surface)	-
8.4.4 (The colour of the hard anodic coating varies depending upon the alloy, thickness of the coating and electrolye. Normally the colour may vary from dark grey (almost black) to light grey. )	-
8.4.5 (When the coated surface is rubbed two or three times with fine emery paper grit number 180 using medium finger pressure, cloth or paper shall not abrade the surface. A faint trace of whitening on the cloth or paper is permissible)	-
9 (The manufacturer shall provide full instructions for use and cleaning for coated or hard anodized utensils)	-
10 (Each vessel shall be legibly and indelibly stamped on the outside surface or handle with the manufacturer’s name or registered trade-mark, size and thickness or class. )	-
( Clauses 4, 4.1, 4.2 and 4.3) (Carbon of IS 6911)	-
( Clauses 4, 4.1, 4.2 and 4.3) (Silicon of IS 6911)	-
( Clauses 4, 4.1, 4.2 and 4.3) (Silicon of IS 737)	-
( Clauses 4, 4.1, 4.2 and 4.3) (Silicon of IS 21)	-
( Clauses 4, 4.1, 4.2 and 4.3) (Phosphorous of IS 6911)	-
( Clauses 4, 4.1, 4.2 and 4.3) (Sulphor of IS 6911)	-
( Clauses 4, 4.1, 4.2 and 4.3) (Manganese of IS 6911)	-
( Clauses 4, 4.1, 4.2 and 4.3) (Manganese of IS 737)	-
( Clauses 4, 4.1, 4.2 and 4.3) (Magnesium of IS 21)	-
( Clauses 4, 4.1, 4.2 and 4.3) (Nickel of IS 6911)	-
( Clauses 4, 4.1, 4.2 and 4.3) (Chromium of IS 6911)	-
( Clauses 4, 4.1, 4.2 and 4.3) (Chromium of IS 737)	-
( Clauses 4, 4.1, 4.2 and 4.3) (Chromium of IS 21)	-
( Clauses 4, 4.1, 4.2 and 4.3) (Molybdenum of IS 6911)	-
( Clauses 4, 4.1, 4.2 and 4.3) (Nitrogen of IS 6911)	-

-
Facility not available for 1) Non stick plastic coating conforming to IS 9730[IS 9730-Thickness(Cl. 4.3), Non stick quality(Cl. 4.4), Adhesion(Cl. 4.6) - Cross hatch test] ; 2) Performance test(Cl. 8.6.1),

292

IS 6902 (1973)

Specification for steel wire for spokes

For all sizes

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 4.1 (Carbon- IS 228)	-
Cl. 4.1 (Manganese- IS 228.)	-
Cl. 4.1 (Sulphur- IS 228.)	-
Cl. 4.1 (Phosphorus- IS 228.)	-
5.1 ( Tensile strength )	-
6.0 ( Bend Test )	-
7.0 (Freedom from defects )	-
8.0 (Wire diameter & Tolerances)	-
8 (Wire diameter & Tolerances)	-
5.1 ( Tensile strength )	-
6 ( Bend Test )	-
7 (Freedom from defects )	-

-
3 m + 100 gm drillings

293

IS 6911 (2017)

Stainless steel plate, sheet and strip - Specification (Second Revision)

For all grades except for the tests mentioned in remarks

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 (Freedom from defects , IS 6911)	-
10.1,Table 4&Table 6 (Tensile Test - IS 1608(Pt -1))	-
10.2,Table 4&Table 5 (Hardness Test- IS 1500(Pt -1),IS 1501 (Pt-1),IS 1586 (Pt -1))	-
10.3 (Bend Test - IS 1599)	-
11,Table 7 (Erichsen cupping test-IS 10175)	-
17 (Dimension and tolerance)	-
Cl. 7.1 & 7.2 Table 1 (Carbon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Silicon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Manganese -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Phosphorus -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Sulphur -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Chromium -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Nickel -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Molybdenum -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Copper -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Niobium-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Titanium-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 7.1 & 7.2 Table 1 (Nitrogen -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.12 (Corrosion Resistance- IS 10461(Part1))	-
Cl.12 (Corrosion Resistance- IS 10461(Part2))	-
Table 1 (Alumium)	-
Table 1, Amendment 2 (Tungstun)	-
Table 1, Amendment 2 (Ta)	-
Table 1, Amendment 2 (Zirconium)	-
Table 1, Amendment 2 (Cobalt)	-

-
Chem- Wire Diameter Should be Greater than 3 mm. Mech- Steel designation and element specified in Cl.7.3 (if applicable) 100 g drillings

294

IS 6603 (2024)

Stainless Steel Semi-Finished Products, Bars, Wire Rods and Bright Bars â Specification (Second Revision)

All Grades and Conditions

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl - 9.1,9.5,13.2 (Thickness or Diameter)	-
Cl-7.1, 7.2 (C)	-
Cl-7.1, 7.2 (Si)	-
Cl-7.1, 7.2 (Mn)	-
Cl-7.1, 7.2 (P)	-
Cl-7.1, 7.2 (S)	-
Cl-7.1, 7.2 (Cr)	-
Cl-7.1, 7.2 (Mo)	-
Cl-7.1, 7.2 (Ni)	-
Cl-7.1, 7.2 (N)	-
Cl-7.1, 7.2 (Ti)	-
Cl-7.1, 7.2 (Cu)	-
Cl-7.1, 7.2 (Nb)	-
Cl-7.1, 7.2 (W)	-
Cl-7.1, 7.2 (V)	-
Cl-7.1, 7.2 (Al)	-
Cl-7.1, 7.2 (Ti: (C + N))	-
Cl-7.1, 7.2 (Boron)	-
cL-7.1, 7.2 (Co)	-

-
Chem- Wire Diameter Should be Greater than 3 mm Mech- Steel designation and element specified in Cl.7.3 (if applicable) to be declared. Prepared sample required for Charpy Impact Test

295

IS 4454 : Part 1 (2001)

Steel wire for mechanical springs - Specification: Part 1 cold drawn unalloyed steel wire (Third Revision)

For all grades except tests mentioned in remarks

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (Workmanship)	-
Cl 9 (Diameter & Difference Between Two Reading On Any Two Diameters)	-
Cl 10 (Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test & Decarburization Test)	-
Cl 10 (Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test & Decarburization Test)	-
Cl 10 (Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test & Decarburization Test)	-
7.1, 7.2 (carbon)	-
7.1, 7.2 (sulphur)	-
7.1, 7.2 (phosphorus)	-
7.1, 7.2 (manganese)	-
7.1, 7.2 (silicon )	-
7.1, 7.2 (copper)	-
Cl 10 (Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test & Decarburization Test)	-
7.1, 7.2 (Vanadium)	-
7.1, 7.2 (nitrogen)	-
7.1, 7.2 (sulphur + phosphorus)	-
7.1, 7.2 (cu + cr+ni)	-

-
Facility not available for Micro alloying elements (V, Nb, Ti)

296

IS 7092 : Part 2 (1987)

Specification for aluminium alloy tube for irrigation purposes: Part 2 extruded tube (Second Revision)

For all sizes excepts tests mentioned in remarks

Rs 11230/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.4 (Workmanship & Finish)	-
Cl. 6.3 (Drift Expanding Test ( Expanded Inside Diameter- IS 2335)	-
Cl.6.2 (0.2 percent proof strength- IS 2657)	-
Cl.6.2 (Elongation on 50 mm gauge length- IS 2657)	-
Cl. 6.3 (Drift Expanding Test ( Expanded Inside Diameter- IS 2335)	-
Cl.7.1, Table 2 (Outside Diameter-)	-
Cl.7.1, Table 2 (Roundness or Ovality)	-
Cl.7.1, Table 2 (Wall Thickness)	-
Cl. 7.2 (Length)	-
Cl. 6.1 (Copper- IS 504 or any other established instrumental/ chemical method)	-
Cl. 6.1 (Magnesium- IS 504 or any other established instrumental/ chemical method)	-
Cl. 6.1 (Silicon- IS 504 or any other established instrumental/ chemical method)	-
Cl. 6.1 (Iron- IS 504 or any other established instrumental/ chemical method)	-
Cl. 6.1 (Manganese- IS 504 or any other established instrumental/ chemical method)	-
Cl. 6.1 (Zinc- IS 504 or any other established instrumental/ chemical method)	-
Cl. 6.1 (Chromium- IS 504 or any other established instrumental/ chemical method)	-
Cl. 6.1 (Titanium and/ other grain refining elements)	-
Cl. 6.1 (Aluminium- IS 504 or any other established instrumental/ chemical method)	-

-
Mech: Facility not available for hydrostatic pressure test Chem: Cl.6.1 Al

297

IS 432 : Part 2 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 2 Hard-Drawn Steel Wire

All sizes

Rs 3900/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 4.1 (Workmanship)	-
Cl 5 & 6 (Diameter)	-
Cl 8.3 (Bending To Both Side At 90°, Then Straight)	-
Clause 3.1.1 (Sulphur)	-
Clause 3.1.1 (Phosphorus)	-
Cl 7 (UTM)	-

-
Complete

298

IS 432 : Part 1 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 1 Mild Steel and Medium Tensile Steel Bars

All size and grades

Rs 2100/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5.1 (Workmanship)	-
Cl 6.2 (Weight)	-
Cl 6.2 (Diameter & Ovality)	-
Cl 8.2 (Bend test)	-
Cl 9.3 (Press)	-
Clause -4, 4.1 ( CARBON)	-
Clause -4, 4.1 (MANGANESE)	-
Clause -4, 4.1 (SULPHUR)	-
Clause -4, 4.1 (PHOSPHURS)	-
Clause -4, 4.1 (SILICON)	-
Clause -4, 4.1 (NITROGEN)	-
Cl 6.2 (Diameter & Ovality)	-
Cl 8.1 (ultimate tensile stress, yield stress and percentage elongation)	-

-
Chemical: Except Aluminum and Vanadium

299

IS 7098 : Part 2 (2011)

Crosslinked polyethylene insulated thermoplastic sheathed cables - Specification: Part 2 for working voltages from 3.3 kV up to and including 33 kV (Second Revision)

Pertial

Rs. 33750/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (CONDUCTOR)	-
4.1.1 (CONDUCTOR)	-
5 (INSULATION)	-
6.1.1 (SCREENING : - Non-metallic — Semiconducting Compound)	-
6.1.2 (SCREENING : - Non-magnetic Metallic Tape for Single Core Unscreened and Unarmoured Cables)	-
7 (FILLERS AND INNER SHEATH)	-
8.1 (ARMOURING)	-
9 (OUTER SHEATH )	-
10.1 (CONDUCTOR)	-
10.2 (CONDUCTOR)	-
11 (CONDUCTOR SCREENING)	-
12.2 (INSULATION : Thickness of Insulation)	-
12.3 (INSULATION : Tolerance on Thickness of Insulation)	-
12.5 (INSULATION : Application of Insulation)	-
13.1 (INSULATION SCREENING)	-
13.2 (INSULATION SCREENING)	-
14.1 (CORE IDENTIFICATION)	-
14.1.1 (CORE IDENTIFICATION)	-
15.1 (LAVING UP OF CORES)	-
16.1 (INNER SHEATH (COMMON COVERING))	-
16.2 (INNER SHEATH (COMMON COVERING))	-
16.3 (INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-
17.1 (ARMOURING : Application )	-
17.3 (ARMOURING : Dimension )	-
17.4 (ARMOURING : Joints)	-
16.4 (ARMOURING : Resistance)	-
18.1 (OUTER SHEATH)	-
18.2 (OUTER SHEATH: Colour)	-
18.3 (Thicknes of outer sheath : average )	-
18.3 (Thicknes of outer sheath : minimum )	-
19.1 i) a) (Annealing test (for copper))	-
19.1 i) b) (Tensile test (for aluminium) - Before stranding )	-
19.1 i) b) (Tensile test (for aluminium) - After stranding )	-
19.1 i) c) (Wrapping test ( for aluminium))	-
19.1 i) d) (Resistance test - Main conductor )	-
19.1 i) d) (Resistance test - Neutral conductor )	-
19.1 v) b) (Volume resistivity)	-
19.1 vi) a) (Physical tests for outer sheath : Tensile stregth )	-
19.1 vi) a) (Physical tests for outer sheath : Elongation )	-
19.1 vi) b) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-
19.1 vi) b) (Physical tests for outer sheath -Ageing in air oven : Elongation )	-
19.1 vi) b) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-
19.1 vi) b) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-
19.1 vi) c) (Phyaical tests for Sheath : Shrinkage )	-
19.1 vi) c) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-
19.1 vi) d) (Sheath : Hot deformation)	-
19.1 vi) e) (Loss of massIn air oven)	-
19.1 vi) f) (Sheath : Heat shock test)	-
19.1 vi) g) (Sheath : Thermalstability)	-
20.8 (Flammability test)	-
21.1 (IDENTIFICATION : Manufacturer's Identification)	-
21.2 (IDENTIFICATION : Cable Identification)	-
21.3 (IDENTIFICATION : Cable Code)	-
12.4 (Eccentricity and Ovality)	-
17.1.2 (ARMOURING )	-
17.1.3 (ARMOURING )	-
17.2 (ARMOURING : Type of armour )	-
19.1 xi) (Insulation resistance test : volume resistivity )	-
20.7 (High voltage test)	-

-
Facility not available for water absorption, partial discharge, impulse withstand, HV test, bending test, heating cycle, dielectric pf test, oxygen index test, flame retardance test

300

IS 1785 : Part 2 (1983)

Specification for plain hard drawn steel wire for prestressed concrete: Part 2 as - Drawn wire (First Revision)

All size

Rs 3000/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5.1 (Diameter)	-
Cl 5.1.2 (Weight)	-
Cl 6.1 (Tensile Test On UTM)	-
Cl 6.2 (Tensile Test On UTM)	-
Cl 6.3 (Tensile Test On UTM)	-
3.1.1 (PHOSPHORUS)	-
3.1.1 (SULPHUR)	-

-
Mech- Except Proof Stress

Bureau of Indian Standards

The National Standards Body of India

BIS, Eastern Regional Laboratory (ERL)

(1) Annex Building & Sample-Cell: Bureau of Indian Standards, P-230, CIT Scheme, VII- M, Block-W,Kankurgachi,Kolkata-700054 (2) Main building: 1/14, CIT Scheme VII M, VIP Road, Kankurgachi,Kolkata-700054, Kolkata, Kolkata, West Bengal, 700054

- sample.erol@bis.gov.in

Scope List