BIS - LIMS (Laboratory Information Management System)

BIS, Eastern Regional Laboratory (ERL)

(1) Annex Building & Sample-Cell: Bureau of Indian Standards, P-230, CIT Scheme, VII- M, Block-W,Kankurgachi,Kolkata-700054 (2) Main building: 1/14, CIT Scheme VII M, VIP Road, Kankurgachi,Kolkata-700054, Kolkata, Kolkata, West Bengal, 700054

- sample.erol@bis.gov.in

Scope List

Reset

353 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

211

IS 8794 (1988)

Specification for cast iron detachable joints for use with asbestos cement pressure pipes (First Revision)

For all DN and Class.

3900/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1, Table 2 (External Dia of AC Pipe(D2))	-
6.1, Table 2 (Inside diaFlange(DI))	-
6.1, Table 2 (External Dia at Centre(DEC))	-
6.1, Table 2 (Collar Width(Wc))	-
6.1, Table 3 (Nominal Dia of Bolt(do))	-
6.1, Table 3 (Minimum prefared length of bolt(L))	-
8.4 (Coating)	-

-
Excluding Cl 5 Hydrostatic test. Prepared piece required for tensile and hardness test.

212

IS 16415 (2015)

Composite cement - Specification

Rs.9150/- View breakup
Chemical Rs.4600/- Mechanical Rs 4550/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 -Table - 2 i (Insoluble residue - Cl 4.10 of IS 4032:1985)	-
6 -Table - 2 ii (Magnesia - Cl 4.8 of IS 4032:1985)	-
6 -Table - 2 iii (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-
6 -Table - 2 iv (Sulphide sulphur (S) - Cl 6.12 of IS 4032:1985)	-
6 -Table - 2 v (Loss on ignition - Cl 4.2 of IS 4032:1985)	-
6 -Table - 2 vi (Chloride content - Cl 4.13 of IS 4032:1985)	-
7 and Table 3 i (Fineness IS 4031(Part 2))	-
7 and Table 3 ii a (Soundness, Le-Chate1ier expansion IS 4031(Part 3) )	-
7 and Table 3 ii b (Soundness, Autoclave expansion IS 4031(Part 3) )	-
7 and Table 3 iii a (Setting Time ( by Vicat Apparatus), Initial IS 4031(Part 5))	-
7 and Table 3 iii b (Setting Time ( by Vicat Apparatus ), Final IS 4031(Part 5))	-
7 and Table 3 iv a (Compretsive Strenqth .72 ± 1 hr IS 4031(Part 6))	-
7 and Table 3 iv b (Compretsive Strenqth 168 ± 2 hr IS 4031(Part 6))	-
7 and Table 3 iv c (Compretsive Strenqth 672 ± 4 hr IS 4031(Part 6))	-
7 and Table 3 v (Drying shrinkage IS 4031(Part 10))	-
Cl. 6.1,Table 2 (Alkali content)	-
7 and Table 3 vi (Transverse strength (optional) IS 4031(Part 8) )	-

-
Mech - Except Transverse Strength (optional), Chem-Declaration for chloride regarding end use of cement (as per Table 1) and declaration of fly ash content & Confirmation for testing Alkali Content required.

213

IS 15410 (2003)

Containers for packaging of natural mineral water and packaged drinking water - Specification

For all capacity

5850 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.6.2 (TRANSPARANCY)	-
4.6.3, clause 6 of IS:2798:1998 (Leakage test- a. Closure leakage )	-
4.6.3, clause 6 of IS:2798:1998 (Leakage test- c. Air pressure leakage)	-
4.6.4 (DROP TEST)	-
4.6.6 (PORTABILITY TEST)	-
4.6.3, clause 6 of IS:2798:1998 (Leakage test- b. Vibration leakage)	-
4.5, IS:2798:1998 (Wall thickness- Bottom, in mm)	-
4.5, IS:2798:1998 (Wall thickness- Middle , in mm)	-
4.5, IS:2798:1998 (Wall thickness- Top , in mm )	-
4.4 , clause 5 of IS:2798:1998 (Brimful capacity in ml)	-
4.3 (Workmanship, Finish & Appearance)	-
4.2 (Design, Shape & Dimension )	-
4.0 (chem) (MATERIAL)	-
Cl. 4.6.5 (chem) (Cl. 4.6.5 Overall migration (Caps))	-
4.6.5.1 (chem) (Colour migration (Caps))	-
4.6.5.1 (chem) (Colour migration (Container))	-
Cl. 4.6.5 (Overall migration for container)	-
Clauses 4.6.7.2 and 4.6.7.3 ,S.No(i) (Specific migration for Cap,Barium)	-
Clauses 4.6.7.2 and 4.6.7.3 ,S.No(ii) (Specific migration for Cap,Cobalt)	-
Clauses 4.6.7.2 and 4.6.7.3 ,S.No(iii) (Specific migration for Cap,Copper)	-
Clauses 4.6.7.2 and 4.6.7.3 ,S.No(iv) (Specific migration for Cap,Iron)	-
Clauses 4.6.7.2 and 4.6.7.3 ,S.No(v) (Specific migration for Cap,Lithium)	-
Clauses 4.6.7.2 and 4.6.7.3 ,S.No(vi) (Specific migration for Cap,Manganese)	-
Clauses 4.6.7.2 and 4.6.7.3 ,S.No(vii) (Specific migration for Cap,Zinc)	-
Clauses 4.6.7.2 and 4.6.7.3 ,S.No(viii) (Specific migration for Cap,Antimony)	-
Clauses 4.6.7.2 and 4.6.7.3 ,S.No(ix) ("Specific migration for Cap,Phthalic acid, bis(2-ethylhexyl) ester (DEHP)")	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (i) (Barium)	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (ii) (Cobalt)	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (iii) (Copper)	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (iv) (Iron)	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (v) (Lithium)	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (vi) (Manganese)	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (vii) (Zinc)	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (viii) (Antimony)	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (ix) (Phthalic acid, bis(2-ethylhexyl) ester (DEHP))	-
4.1 (Material)	-
Cl. 4.6.5 (chem) (Cl. 4.6.5 Color migration (Caps))	-
Cl. 4.6.5 (Cl. 4.6.5 Migration)	-
4.6.5.1.b (Colour migration Test (Cap))	-
4.6.5.1.a (Colour migration Test (Container))	-
CL 4.6.7.2 and 4.6.7.3, Table 3 (i) (Barium)	-
CL 4.6.7.2 and 4.6.7.3, Table 3 (ii) (Cobalt)	-
CL 4.6.7.2 and 4.6.7.3, Table 3 (iii) (Copper)	-
CL 4.6.7.2 and 4.6.7.3, Table 3 (iv) (Iron)	-
CL 4.6.7.2 and 4.6.7.3, Table 3 (v) (Lithium)	-
CL 4.6.7.2 and 4.6.7.3, Table 3 (vi) (Manganese)	-
CL 4.6.7.2 and 4.6.7.3, Table 3 (vii) (Zinc)	-
CL 4.6.7.2 and 4.6.7.3, Table 3 (viii) (Antimony)	-
CL 4.6.7.2 and 4.6.7.3, Table 3 (ix) (Phthalic acid, bis(2-ethylhexyl) ester (DEHP))	-
4.1 (Material)	-
4.6.5 (Migration Test)	-
Clauses 5.3.9.2 and 5.3.9.3,Table 3, S.no.(ix) (Phthalic acid, bis(2-ethylhexyl)ester (DEHP)-ISO 18856)	-
Cl. 4.1 (Material test for container)	-
Cl. 4.6.5.1 (Colour migration for container)	-
Clauses 4.6.7.2 and 4.6.7.3 ,S.No(i) (Specific migration for container,Barium)	-
Clauses 4.6.7.2 and 4.6.7.3 ,S.No(ii) (Specific migration for container,Cobalt)	-
Clauses 4.6.7.2 and 4.6.7.3 ,S.No(iii) (Specific migration for container,Copper)	-
Clauses 4.6.7.2 and 4.6.7.3 ,S.No(iv) (Specific migration for container,Iron)	-
Clauses 4.6.7.2 and 4.6.7.3 ,S.No(v) (Specific migration for container,Lithium)	-
Clauses 4.6.7.2 and 4.6.7.3 ,S.No(vi) (Specific migration for container,Manganese)	-
Clauses 4.6.7.2 and 4.6.7.3 ,S.No(vii) (Specific migration for container,Zinc)	-
Clauses 4.6.7.2 and 4.6.7.3 ,S.No(viii) (Specific migration for container,Antimony)	-
Clauses 4.6.7.2 and 4.6.7.3 ,S.No(ix) ("Specific migration for container,Phthalic acid, bis(2-ethylhexyl) ester (DEHP)")	-
Cl. 4.6.5 (Overall migration for Cap)	-
Cl. 4.6.5.1 (Colour migration for Cap)	-
5 (Marking)	-
5 (Packing and Marking)	-

-
Material test being done for PET only.

214

IS 12591 (2018)

Cold - Reduced tinmill products - Electrolytic chromium / chromium oxide - Coated steel (Second Revision)

For all grades except for the test mentioned in remarks

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
9.3 ,Table B.1 (Tensile property requirement , Annex D ; ISO 6892-1)	-
10.2.1 (Thickness)	-
10.2.2 (Feather edge)	-
10.3 (Width)	-
10.4.2 (Length of sheet)	-
10.5 (Edge camber)	-
10.6 (Out of square)	-
Annex C (Carbon- NA)	-
Annex C (Sulphur- NA)	-
Annex C (Phosphorous- NA)	-
Annex C (Manganese- NA)	-
8,Table 2 (Chromium/chromium in oxide coating mass)	-

-
Except Si (<0.03%)

215

IS 3736 (1995)

Canvas boots, rubber sole - Specification (Second Revision)

For all type and size

Rs 7650/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.4.1.7.4 Ageing (The boots shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the soles and heels of the boots shall conform to the physical requirements prescribed in Table 5. i) Tensile Length)	-
Cl.4.1.7.2 IS 3400 (Part 2) : 1980 (2)Hardness, IRHD)	-
4.1.6 Fabric Laces Cl.4.1.6.1 ( The boots shall be provided with braided of cotton or man made or blended fabric laces 115 ± 5 cm in length, matching the colour of the upper. )	-
Cl.4.1.1 upper IS 1969 (d) Picks/dm)	-
Cl.4.4.5 ( Table 1.) (d) Picks/dm)	-
4.1.2 Lining Material (195 ± 5 picks/dm shall be used.)	-
Cl.4.1.1 upper IS 1969 (c) Ends/dm )	-
Cl.4.4.5 ( Table 1.) (c) Ends/dm )	-
4.1.2 Lining Material (having 390 ± 10 ends/dm and )	-
Cl.4.1.7.2 IS 3400 (Part 4) : 1987 IS 3400 (Part 2) : 1980 (Change in initial hardness after accelerated ageing for 24 h at l00 ± 1°C)	-
Cl.4.8 Adhesion Test (From the upper foxing portion where it is adhered to the canvas cut a strip of 8.0 ± 0.5 mm width along with the length of the sole at the waist portion and of sufficient lengh to permit separation over a length of at least 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10 mm per minute in accordance with IS 3400 (Part 5):1986 or the Static Dead Load Method as given in Annex C. The individual adhesion value noted/recorded shall not be less than 8 N (0.8 kgf) for each of the test pieces ( see Note under 4.7 ).')	-
Cl.4.4.9 (From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine)	-
Cl.4.1.7.2 IS 3400 (Part 1) : 1987 (Tensile strength in MPa, Min)	-
Cl.4.1.3 Binding Material IS 1954:1990 (Cotton tape NEWAR used as binding material shall conform to the requirements as mentioned in Table 2, when tested in accordance with the methods referred to in col 4 of Table 2. 1)Width, mm. Min )	-
Cl.4.4.3 (The top, side and front edges of the quarters and tongue shall be bound with cotton tape NEWAR of not less than 13 mm width using variety No. 29 thread.)	-
Cl.4.1.7.3 IS 3400 (Part 10) : 1977 (Compression set, in percent. Max)	-
Cl.4.4.4 ( The back of the quarter shall be reinforced with a strip, not less than 25 mm wide,of either upper material or canvas. In case of composite upper material the edges of the strip shall be bound by cotton tape ( NEWAR ). When canvas cloth is used the edges shall be folded and shall be stitched with two rows of stitching.)	-
Cl.4.7 Consolidation Test (From the quarter, cut a strip of 25.0 ± 0. 5 mm width along the length of the boot and of sufficient length to permit separation over a length of 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10mm per minute in accordance with IS 3400 (Part 5): 1986 or Static Dead Load Method as given in Annex C. The individual adhesion value for consolidation test shall not be less than 30 N (3.0 kgf) for each of the test pieces)	-
Cl.4.1.7.2 IS 3400 (Part 1) : 1987 (Elongation at break, in percent, Min)	-
IS 1969:1985 (Breaking load on 50 cm test length. N, Min)	-
4.1.6 Fabric Laces Cl.4.1.6.1 (The laces shall have a minimum breaking load of 450 N, when tested between 18 cm grips, the rate of traverse of power actuated grip being 30 cm/min.)	-
Cl.4.1.7.2 IS 3400 (Part 16) : 1974 (iii)Flexing resistance, number of cycles b)Cut growth at the end of 150 000 cycles, Percent, Max)	-
Cl.4.4.5 ( Table 1.) (b) Weft )	-
Cl.4.4.5 ( Table 1.) ( in case of half bellow. Thefull bellow tongue shall be made out of canvas cloth as prescribed in Sl No. (i) of Table 1. Breaking load in N, Min a) Warp )	-
Cl.4.1.1 upper IS 1969 (b)Weft)	-
Cl.4.1.1 upper IS 1969 (Breaking load in N.Min (5 × 20 cm grip): a) Wrap)	-
Cl.4.1.7.2 IS 3400 (Part 16) : 1974 (iii)Flexing resistance, number of cycles a)Initial crack, Min)	-
4.1.2 Lining Material ( 200 N Minin weft way (when tested in accordance with IS 1969 : 1985) )	-
4.1.2 Lining Material (For covering of the insole, cotton drill conforming to Table 1, Sl No. (ii) shall be used. For detachable insole, bleached cotton twill of breaking load 390 N Min in warp way and)	-
Cl.4.1.4 Reinforcement Material (The back seam, joining two quarters at the back of the heel shall be reinforced with a not less than 25 mm wide tape made out of material conforming to Sl No. (i) of Table 1)	-
Cl.4.1.5 Thread for Upper Closing Cl.4.1.5.1 (IS 1670:1991) (Sewing thread cotton, man made or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirements. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirement of specification.')	-
4.1.6 Fabric Laces Cl.4.1.6.1 (The two ends of the lace shall be provided with suitable metal or plastic tips. Black laces shall be free from sulphur dyes when tested in accordance with Annex B.)	-
Cl.4.1.7.2 IS 3400 (Part 9) : 1978 ( The rubber components shall conform to Table 4 when tested.' ( Page 3, Table 4, Note 1) — 'However in case it is not possible then 4.2.5.3 of IS 13695:1993 shall be followed. 1)Relative density, Max)	-
Cl.4.1.7.5 Thickness of components (Individual components of the boots shall comply with the thickness and material requirements prescribed in Table 6.)	-
Cl.4.3 Leg Height (The leg height of the boots for size 8 shall be 160 ± 2 mm with an increase or decrease of 4 mm of the nominal height for each bigger or smaller sizes respectively when measured at the inside from the back of the boot from insole to the top.)	-
Cl.4.4.2 ( The canvas upper shall be lined with bleached drill cloth.)	-
Cl.4.4.3 ( The upper shall be stitched on a lockstitch machine, with 30 to 40 stitches per decimetre by thread of variety No. 8 and variety No. 29 cotton sewing thread conforming to 4.1.5 using variety No. 29 for taping and binding and variety No. 8 for remaining seams. )	-
Cl.4.4.5 ( The tongue shall be either half or full bellow depending on the requirement of the purchaser andshall be made from composite material prescribed for the upper in 4.1.1.)	-
Cl.4.4.6 ( A minimum of seven aluminium, brass or steel eyelets having 10 mm diameter and wall thickness 0.30 to 0.35 mm shall be fitted in each face.')	-
Cl.4.4.7 ( The toe shall be reinforced with a toe puff cemented inside and outside with rubber toe cap. The heel piece (counter) or stiffener shall be set from the bottom of the lining and bound flat on the top edge with white cloth for binding of countertop edge with white clothfor binding of counter)	-
Cl.4.4.8 ( A strengthening rubber arch piece shall be firmly pasted and stitched at the middle arch of the inside quarter. Another strengthening rubber piece, circular in shape 35 ± 1 mm in diameter, may bepasted and stitched at the centre of the inside)	-
Cl.4.4.10 ( A 25 mm Min wide and 2 mm Min thick rubber golosh in serrated, diamond or any otherdesign, as agreed to between the purchaser and thesupplier, shall be fitted all round the sole edge of the boot. The golosh shall not extend below the edge of the sole.)	-
Cl.4.5.1(Cl.4.1.6.) ( Each pair of boot shall be provided with a pair of braided fabric laces of the quality as prescribed in 4.1.6.)	-
Cl.4.5.2 ( In appearance, general workmanship, finish and in all other respects, not defined in this standard, the boot shall be similar to those of the sample approved by the purchaser, if any.)	-
Cl.4.6 Mass (The mass of finished boots, rubber sole, of size 8 shall not exceed 1130 g per pair, and the mass shall increase or decrease by 75 g per pair for each bigger or smaller size respectively.)	-
Cl.4.9 Composite Breaking Strength Test ( From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine.Rate of traverse of pulling jaw shall be 100 ± 5 mm per minute. Two such test pieces will be required to be obtained from the made up footwear and will be subjected to test to break each test piece. Mean value of each set of test pieces comprising of length wise and height wise test pieces will be 1 000 N/25 mm width minimum.')	-
Cl.4.1.3.3 ( Black tapes shall be free from sulphur dyes when tested in accordance with Annex B.)	-

-
Mech- Except Colour fastness (Cl 4.1.1.1, Cl 4.1.1.2 , Cl 4.1.3.1, Cl 4.1.3.2, Cl 4.1.6.2, Cl 4.1.6.3). Sample req- Mech-3 pairs + raw mat, Chem-1 pair

216

IS 7181 (1986)

Specification for horizontally cast iron double flanged pipes for water, gas and sewage (First Revision)

All sizes

Rs.6600/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2 (Manufacture)	-
3.3 (Manufacture)	-
3.4 (Manufacture)	-
3.1 (Manufacture)	-
5.1 (Tensile Test)	-
7.1 (Sizes and Mass)	-
7.2 (Sizes and Mass)	-
7.3 (Sizes and Mass)	-
7.3 (Sizes and Mass)	-
7.4 (Sizes and Mass Dimensions of Flange)	-
7.4 (Sizes and Mass Dimensions of Flange)	-
7.4 (Sizes and Mass Dimensions of Flange)	-
7.4 (Sizes and Mass Dimensions of Flange)	-
9 (Coating)	-

-
Except Cl 6 Hydrostatic test

217

IS 9523 (2000)

Ductile iron fittings for pressure pipes for water, gas and sewage - Specification (First Revision)

For all sizes

Rs.7245.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5 (Thickness)	-
Cl 9 (Tensile Test & Hardness Test)	-
Cl 11 (Nominal Diameter, Ovality, Dimensions, No. Of Holes & Bolt Sizes)	-
Cl 13 (Coating)	-

-
Except Hydrostatic test, . Sample req-1 pc and Cut pc for coating, Cut portion for dimension, cement lining, prepared test pc for tensile and hardness

218

IS 5557 (2004)

Industrial and protective rubber knee and ankle boots - Specification (Fourth Revision)

For all type and variety

Rs 14030/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5/5.1.7/5.1.7.8 (REQUIREMENTS- Physical Requirements-Resistance to oil)	-
5/5.1.1-Fig. 1, Fig. 2 and Fig. 3 (REQUIREMENTS-Design)	-
5/5.1.2 -IS 1638 (REQUIREMENTS-Size)	-
5/5.1.3-Table1 (REQUIREMENTS-Thickness)	-
5/5.1.4/5.1.4.1-Table2 (REQUIREMENTS-Materials-Rubber components)	-
5/5.1.4/5.1.4.2 (REQUIREMENTS-Materials-Fabric- accordance with IS 1969)	-
5/5.1.4/5.1.4.3 (REQUIREMENTS-Materials-Protective Steel Toe Cap- an per IS 5852)	-
5/5.1.6/5.1.6.1-Fig. 1, Fig. 2, Fig. 3, .Fig. 4, Fig. 5 and Table 3. (REQUIREMENTS- Construction)	-
5/5.1.6/5.1.6.2 (REQUIREMENTS- Construction)	-
5/5.1.7/5.1.7.1 (REQUIREMENTS- Physical Requirements-Heat treatment- as per IS 3400 (Part 4))	-
5/5.1.7/5.1.7.2 (REQUIREMENTS- Physical Requirements-Composite strength)	-
5/5.1.7/5.1.7.3-Table 4 (REQUIREMENTS- Physical Requirements-Flexing endurance- as per Annex B.)	-
5/5.1.7/5.1.7.4 (REQUIREMENTS- Physical Requirements- Leakage resistance test)	-
5/5.1.7/5.1.7.5 (REQUIREMENTS- Physical Requirements- Consolidation test- as per IS IS 3400 (Part 5))	-
5/5.1.7/5.1.7.6 (REQUIREMENTS- Physical Requirements- Performance test- as per Annex C)	-
5/5.1.7/5.1.7.7 (REQUIREMENTS- Physical Requirements-Height of the boots)	-

-
Sample required- 3 pairs & buttons and prepared slab for tensile & elongation as applicable to be supplied separately. Type to be declared.

219

IS 6913 (1973)

Specification for stainless steel tubes for the food and beverage industry

For all grades except for the tests mentioned in remarks

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 6.1, Table 2 (Outside Diameter)	-
Cl. 6.1, Table 2 (Wall Thickness)	-
Cl. 8.1 (Finish-Cl.8.1)	-
Cl. 8.2 (Finish-Cl.8.2)	-
Cl. 10.1 (Tensile Strength- IS 1894)	-
Cl. 10.1 (Elongation on 5.65√So)	-

-
Except Parameter: S,Mo, 14 Hydrostatic test, 15 Optional Tests (Intergrannualr corrosion test)

220

IS 6649 (1985)

Specification for hardened and tempered washers for high strength structural bolts and nuts (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3 Table-1 (Dimensions Type A- d1)	-
3 Table-1 (Dimensions Type A- d2)	-
3 Table-1 (Dimensions Type A- S)	-
3 Table-2 (Dimensions Type B&C- d)	-
3 Table-2 (Dimensions Type B&C- a)	-
3 Table-2 (Dimensions Type B&C- t)	-
3 Table-2 (Dimensions Type B&C- θ)	-
3.1 (Deviation)	-
3.2 (Concentric)	-
3.3 (Clearance)	-
7 (Hardness)	-
8 (Finish)	-
8.1 (Freedom from defect)	-
8.1 (Uniformity of zinc coating)	-
8.1 (Mass of zinc coating)	-
8.1 (Knife test (Adhesion of coating))	-
5 (Chemical Composition- Sulphur)	-
5 (Chemical Composition- Phosphorus)	-

-
Complete

221

IS 5676 (1995)

Moulded solid rubber soles and heels - SpecificatlOn (Second Revision)

For all type

Rs.5100/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5/5.1 (REQUIREMENTS-General)	-
5/5.2- Fig. 1 to 5 (REQUIREMENTS-Design)	-
5/5.5- Table1 (REQUIREMENTS-Thickness)	-
5/5.6/5.6.1 (REQUIREMENTS-Channel)	-
5/5.7- Table2 (REQUIREMENTS- Physical Requirements- as per IS 3400 (Part 1, Part 2, Part 4, Part 9, Part 10, Part 16))	-
5.7, Table 2 iv) (Amendment 1) (Abrasion Resistance at applied force of 10 N)	-
5.7, Table 2 vii) (Amendment 1) (Tear strength (average force))	-
5.5 (Amendment 1) (Thickness)	-
5.7 Table 2 i) (Amendment 1) (Relative Density)	-
5.7, Table 2 ii) (Amendment 1) (Hardness, degree, Shore A)	-
5.7, Table 2 v) (Amendment 1) (Tensile strength)	-
5.7, Table 2 vi) (Amendment 1) (Elongation at break)	-
5.7, Table 2 iii) (Amendment 1) (Flexing resistance)	-
5/5.3/5.3.1 (REQUIREMENTS- Construction)	-
5/5.3/5.3.1 (REQUIREMENTS- Construction)	-
5/5.1 (REQUIREMENTS-General)	-
5/5.2- Fig. 1 to 5 (REQUIREMENTS-Design)	-
5/5.5- Table1 (REQUIREMENTS-Thickness)	-
5/5.6/5.6.1 (REQUIREMENTS-Channel)	-
5/5.7- Table2 (REQUIREMENTS- Physical Requirements- as per IS 3400 (Part 1, Part 2, Part 4, Part 9, Part 10, Part 16))	-
5/5.3/5.3.1 (REQUIREMENTS- Construction)	-
5/5.1 (REQUIREMENTS-General)	-
5/5.2- Fig. 1 to 5 (REQUIREMENTS-Design)	-
5/5.5- Table1 (REQUIREMENTS-Thickness)	-
5/5.6/5.6.1 (REQUIREMENTS-Channel)	-
5/5.7- Table2 (REQUIREMENTS- Physical Requirements- as per IS 3400 (Part 1, Part 2, Part 4, Part 9, Part 10, Part 16))	-
6 (Marking and packing)	-
8.1 (Test methods)	-
8.3 (Measurement of thickness)	-
Cl.6.1,6.2,6.3 (Marking and packing)	-
8.1 (Test Methods)	-
Cl.8.3 (Measurement of thickness ")	-

-
2 nos. soles + 2 slab (200mm x 200mm, Thickness 1.8-2.2 mm)

222

IS 4109 (1967)

Specification for kadahies

For all shapes except tests mentioned in remarks

Rs. 750/- and testing charges as per referred Iss View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2 (Materials)	-
3 (a) Round Shape / Bowl Shape)	-
3 (b) Nominal dia. at top D1 mm)	-
3 (c) Nominal overall Height H1 mm)	-
3 (d) Thickness at bottom mm Min)	-
4 (Manufacture and Workmanship)	-
6 (Test)	-

-
Chem: except Nb, V ,B Ti

223

IS 6528 (1995)

Stainless steel wire - Specification (First Revision)

For all grades except for the tests mentioned in remarks

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 6 (Workmanship)	-
Cl 9.1 & Table 3 (Diameter & Out Of Round)	-
Cl 9.1 & Table 3 (Diameter & Out Of Round)	-
Cl 9.1 & Table 3 (Diameter & Out Of Round)	-
Cl 10 (UTM)	-
Cl 10 (UTM)	-
Cl 10 (UTM)	-
Cl 10 (UTM)	-
Cl 10 (UTM)	-
Cl 10 (UTM)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Carbon)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Sulphor)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Phosphorous)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Manganese)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Silicon)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Chromium)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Nickel)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Molybdenum)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Copper)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Nitrogen)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Aluminium)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Titanium)	-

-
Facility not available for S, Al, Mo more than 1.5%, Ti & Nb

224

IS 6527 (1995)

Stainless steel wire rods - Specification (First Revision)

For all designation except for the tests mentioned in remarks

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 9 (Tensile & Hardness)	-
Cl 9 (Tensile & Hardness)	-
Cl 9 (Tensile & Hardness)	-
Cl 9 (Tensile & Hardness)	-
Cl 10 (Diameter & Out Of Round)	-
Cl 10 (Diameter & Out Of Round)	-
7, Table 1of IS:6527 (Designation X04Cr13) (Carbon)	-
7, Table 1of IS:6527 (Designation X04Cr13) (Silicon)	-
7, Table 1of IS:6527 (Designation X04Cr13) (Manganese)	-
7, Table 1of IS:6527 (Designation X04Cr13) (Nickel)	-
7, Table 1of IS:6527 (Designation X04Cr13) (Chromium)	-
7, Table 1of IS:6527 (Designation X04Cr13) (Phosphorous)	-
7, Table 1of IS:6527 (Designation X04Cr13) (Copper)	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4) (Titanium)	-
7, Table 1of IS:6527 (Designation X04Cr13) (Aluminium)	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4) (Niobium)	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4) (Molybdenum)	-
7, Table 1of IS:6527 (Designation X04Cr13) (Sulphur)	-

-
Steel designation is required and hardness below 20 mm Dia and 0.4mm thickness

225

IS 1322 (1993)

Bitumen Felts for Water Proofing and Damp-proofing

For all types except tests mentioned in the remarks

Rs.8300/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.4 & Table 1 (Weight )	-
5.5 (Free from external defects - IS 1322)	-
6 (Dimension-IS 1322)	-
7.1 (Breaking Strength test- IS 13826(Part 1))	-
7.1 (Pliabilitry Test-IS 13826(Part 2))	-
7.1 (Strage Sticking Test-IS 13826(Part 3))	-
7.1 (Pressure Head Test-IS 13826(Part-4 )	-
7.1 (Heat Resistance Test-IS 13826(Part 5))	-
7.1 (Water Absorption Test-IS 13826(Part 6))	-
3.1.1 (Fibre Base)	-
3.1.2 (Hessian Base)	-
4.2.1 (Composition)	-
4.1.1 (Fibre base felt)	-

-
Complete

226

IS 11652 (2017)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg cement – Specification (third revision)

16450 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2 (width of tape, 2.5 mm ± 0.1 mm)	-
Fig. 1- Table 1- Sr. no. ii (Ends per dm - Annex B 40 ± 2 )	-
Fig. 1- Table 1-Sr. no. iii (Picks per dm-Annex B 40 ± 2 )	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note )- Annex B c) Width of gusset (e) 76 ± 10 mm )	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B d) Width of valve (v) 100, + 10/-5 mm )	-
Fig. 1- Table 1-Sr. no. i (Dimensions, mm (see Note )- Annex B b) Width of sack (w) 480 ± 10 mm )	-
Fig. 1, Table 1 (i) Dimensions, mm (see Note ) -Annex B a) Length of sack, inside (l), 710 ± 10 mm )	-
4.4 (Seam The two rows of stitches shall be separated from each other by minimum 5 mm and )	-
4.4 (Seam The outer stitch shall be minimum 8 mm from the outer edge of the sacks. )	-
4.4 (Seam The stitching shall be done with double fold over seam to)	-
4.4 (The number of stitches/dm shall be 14 ± 2.)	-
5/5.1-Table 1-Sr. no. iv (Requirements, Mass of Sack- IS 1964 a) Non-gusseted type 70 + 6%)	-
5/5.1-Table 1-Sr. no. iv (Requirements, Mass of Sack- IS 1964 a) gusseted type 71 + 6%)	-
5/5.1 (The mass of bale of sacks (excluding packing materials) shall be within ± 3 percent of the mass calculated by multiplying the number of sacks with the mass of sack specified in Table 1.)	-
5/5.3-Table 1-Sr. no.v (Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): -1969 (Part 1) a) Lengthwise , 900 (91.8) )	-
5/5.3-Table 1-Sr. no.v (Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): - 1969 (Part 1) b) Widthwise , 900 (91.8) )	-
5/5.3-Table 1-Sr. no.vi (Breaking strength of top seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-
5/5.3-Table 1-Sr. no.vi (Breaking strength of bottom seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-
5/5.3-Table 1-Sr. no.vii (Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) a) Lengthwise 15 to 25)	-
5/5.3-Table 1-Sr. no.vii (Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) b) Widthwise 15 to 25)	-
5/5.5-Table 1-Sr. no.viii (Ash content Max percent- Annex D a) For UV stabilized sacks 2.2 )	-
5/5.5-Table 1-Sr. no.viii (Ash content Max percent- Annex D b) For non-UV stabilized sacks 6 )	-
5/5.6 (UV Resistance, )	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to a) UV Radiation -Annex F )	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to b) Accelerated Weathering - Annex F )	-

-
Complete

227

IS 11587 (1986)

Specification for structural weather resistant steels

For all grades except for the test mentioned in remarks

- View breakup
Testing Charges for Mechanical testing for the product is: Rs 5600/- (rounded off to nearest Rs 50/-) Testing charges for Chemical parameters in Table 1 is Rs. 8600/- (rounded off to nearest 50/-).

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (Tensile Test)	-
Cl 9 (Bend Test)	-
Cl 10 (Impact Test)	-
Cl 11 (Flattening Test)	-
Cl 12 (Freedom from Defects)	-
Cl 13 (Dimensions)	-
Cl 16 (Mass)	-
Clause 5.1, Table -1 (WR-Fe 480 A, C )	-
Clause 5.1, Table -1 (WR-Fe 480 A, Si)	-
Clause 5.1, Table -1 (WR-Fe 480 A, Mn)	-
Clause 5.1, Table -1 (WR-Fe 480 A, P )	-
Clause 5.1, Table -1 (WR-Fe 480 A, S )	-
Clause 5.1, Table -1 (WR-Fe 480 A, Cr )	-
Clause 5.1, Table -1 (WR-Fe 480 A, Ni)	-
Clause 5.1, Table -1 (WR-Fe 480 A, Cu)	-
Clause 5.1, Table -1 (WR-Fe 480 B, V)	-
Clause 5.1, Table -1 (WR-Fe 480 B, C )	-
Clause 5.1, Table -1 (WR-Fe 480 B, Si)	-
Clause 5.1, Table -1 (WR-Fe 480 B, Mn)	-
Clause 5.1, Table -1 (WR-Fe 480 B, P )	-
Clause 5.1, Table -1 (WR-Fe 480 B, S )	-
Clause 5.1, Table -1 (WR-Fe 480 B, Cr )	-
Clause 5.1, Table -1 (WR-Fe 480 B, Cu)	-
Clause 5.1, Table -1 (WR-Fe 500, C)	-
Clause 5.1, Table -1 (WR-Fe 500, Si)	-
Clause 5.1, Table -1 (WR-Fe 500, Mn)	-
Clause 5.1, Table -1 (WR-Fe 500, P)	-
Clause 5.1, Table -1 (WR-Fe 500, S)	-
Clause 5.1, Table -1 (WR-Fe 500, Cr)	-
Clause 5.1, Table -1 (WR-Fe 500, V)	-

-
-

228

IS 13620 (1993)

Fusion Bonded Epoxy Coated Reinforcing Bars -

For all grades except for the tests mentioned in remarks

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 7.2 (Continuity Of Coating)	-
Cl 7.3 (Adhesion )	-
4.1 (Carbon- IS 228(Part 1))	-
4.1 (Sulphur- IS 228(Part 9))	-
4.1 (Phosphorous- IS 228(Part 3))	-
4.1 (Sulphur & Phosphorous)	-
4.1 (Carbon Equivalent)	-
Cl 7.1 (Coating Thickness)	-
Cl 7.2 (Continuity Of Coating)	-
Cl 7.3 (Adhesion )	-
Cl 7.1 (Coating Thickness)	-
Cl 7.2 (Continuity Of Coating)	-
Cl 7.3 (Adhesion )	-
Cl 7.1 (Coating Thickness)	-
4.1 (Cr+Cu+Ni+Mo+P)	-

-
Facility not available for Nb, V, Ti, Al, Cl 4.1 Pull out test, Abrasion Resistance 1 m of coated bar as per IS 13620 & 2 x 1 m of HSDS bar as per IS 1786

229

IS 1989 : Part 2 (1986)

Specification for leather safety boots and shoes: Part 2 for heavy metal industries (Fourth Revision)

For all

Rs 5100/- for safety boots, Rs.4500/- safety shoes View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (Marking)	-
7 (Design)	-
8 (a) Upper Leather)	-
8 (b) Lining Leather)	-
8 (c) Bottom Material)	-
8 (d) Steel Toe Cap)	-
8 (e) Tape)	-
8 (f) Bottom Filling)	-
8 (g) Eyelet)	-
8 (h) Toe Compound)	-
8 (i) Threads)	-
8 (j) Rivets)	-
8 (k) Screw Wire)	-
8 (l) Heel Pin)	-
8 (m) Shank)	-
8 (n) Laces)	-
8 (o) Tongue Lining)	-
8 (p) Adhesive)	-
8 (q) Strengthening Piece)	-
8 (r) Leather Components)	-
9 (Manufacture)	-
10 (Finish)	-
11 (a) Boots with Leather Sole and Heel)	-
11 (b) Boots with Rubber Sole and Heel)	-
12 (Performance Test)	-
13 (Design)	-
14 (a) Upper Leather)	-
14 (b) Lining Leather)	-
14 (c) Bottom Material)	-
14 (d) Steel Toe Cap)	-
14 (e) Tape)	-
14 (f) Bottom Filling)	-
14 (g) Eyelet)	-
14 (h) Toe Compound)	-
14 (i) Threads)	-
14 (j) Rivets)	-
14 (k) Screw Wire)	-
14 (l) Heel Pin)	-
14 (m) Shank)	-
14 (n) Laces)	-
14 (o) Tongue Lining)	-
14 (p) Adhesive)	-
14 (q) Leather Components)	-
15 (Manufacture)	-
16 (Finish)	-
17 (a) Shoes with Leather Sole and Heel)	-
17 (b) Shoes with Rubber Sole and Heel)	-
18 (Performance Test)	-

-
Mech- 2 pairs, Chem-1 pair

230

IS 2573 (1986)

Specification for leather gauntlets and mittens (Second Revision)

7400 View breakup
Rs.7400/- (excluding shrinkage temperature test and test of length)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 4.2.1, Table 1, Sr. No. 1 (Solvent extractable substances)	-
Cl 4.2.1, Table 1, Sr. No. 2 (Chromium content, (as Cr₂O₃))	-
Cl 4.2.1, Table 1, Sr. No. 3 (pH of aqueous extract)	-
Cl.4.1 Fig. 1 to 3. (The three types shall be made to the shape and design as shown in Fig. 1 to 3.)	-
Cl .4.2.1 ( Leather - Chrome tanned/ chrome retanned full grain leather or flesh splits manufactured from cow or buffalo hides conforming to the following requirements shall be used a) The leather and flesh split shall have thickness of 1.0 to 1.5 mm;)	-
Cl.4.3.1.2 ( The hand part shall be cut from the piece of undyed leather and back portion including second, third and fourth fingers from different pieces of undyed leather.)	-
Cl. 4.3.1.3 ( The three different pieces of back portion shall be assembled and stitched together along the edges by a row of stitches. The back thus formed shall be secured with the corresponding front pieces ( palm side ) of the fingers with a row of stitches. The thumb shall be made from two pieces of undyed leather and closed with the hand part by a seam. The seam of the thumb shall be reinforced by a strip of leather and secured by two rows of stitches.)	-
Cl 4.3.1.4 ( The hand part shall be made with the flesh side up and the grain side to remain in contact with the hand.)	-
Cl.4.3.1.5 ( The cuff portion shall be made from two pieces of leather, the inner portion being of leather, chrome tanned, natural colour and the outer portion made of chrome tanned leather, with grain side out.)	-
Cl.4.3.2.6 ( The joint at the palm and the thumb shall be reinforced with the same quality of leather as used for the inner face and stitched by two rows of stitches.)	-
Cl.4.3.1.7 ( A dyed leather piece cut to the shape of a semi-circle shall be stitched on the inner part of the cuff along the joint of the hand and the cuff portions by a single row of stitches as shown in Fig. 1. The semi-circular piece of leather shall be not less than 75 mm in diameter.)	-
Cl.4.3.1.8 ( The gauntlets shall be machine stitched.)	-
Cl.4.3.1.9 ( The number of stitches for all the stitchings shall be 6 to 8 stitches per 25)	-
Cl.4.3.1.10 (All losse ends of stitching threads shall be securely fastened)	-
Cl.4.3.1.11 ( ship and finish, and in all other respects not defined in this standard, the gauntlets shall conform to the approved sample.)	-
Cl.4.3.2.2 ( The inner face of the gauntlets including the inner portion of index, second, third and fourth fingers shall be cut from one piece of leather. The thumb shall be cut from a separate piece of leather.)	-
Cl.4.3.2.3 ( The leather components shall be assembled with the flesh side up, the grain side being inside.)	-
Cl.4.3.2.4 ( The outer face of the gauntlets including index second, third and fourth fingers shall be cut from one piece of canvas.)	-
Cl.4.3.2.5 ( The thumb shall be made with the two cut sides placed together and stitched with one row of stitches. The thumb thus formed shall be attached to palm portion through the cut hole and secured by two rows of stitches as shown in Fig. 2.)	-
Cl.4.3.2.6 ( The joint at the palm and the thumb shall be reinforced with the same quality of leather as used for the inner face and stitched by two rows of stitches.)	-
Cl.4.3.2.7 ( The back portion made of canvas shall be secured with the corresponding palm piece made of leather by two rows of stitches with the edges of both leather and canvas placed inside.)	-
Cl.4.3.2.8 ( A leather strip, 20 mm wide and of the same quality of leather used for the inner face of the gauntlet, shall be used for reinforcing the face of canvas over the knuckles. The reinforcement piece shall be placed side up and secured by four rows of stitches.)	-
Cl.4.3.2.9 ( The cuff portion shall be made from one piece of canvas, the side edges being stitched together by double row of stitches with the ends placed inside. The cuff thus formed shall be secured to the hand part by two rows of stitches with the edges of the material placed inside. The bottom edge of the cuff shall be hemmed ( 6 mm ) with the row edges properly turned in.)	-
Cl.4.3.2.10 ( the gauntlets shall be machine stitched.)	-
Cl.4.3.2.11 ( The number of stitches for all the stitchings shall be 6 to 8 stitches per 25 mm. All loose ends of stitching threads shall be securely fastened.)	-
Cl.4.3.2.12 ( Workmanship and finish, and in all other respects not defined in this standard, the gauntlets shall conform to the approved sample.)	-
Cl.4.3.3.2 ( The palm including the inner component of the compartment for the four fingers shall be cut from one piece of leather and the thumb from a separate piece.)	-
Cl.4.3.3.3 ( The leather components shall be assembled with the flesh side out, the grain side being inside.)	-
Cl.4.3.3.4 ( The back portion including the outer component of the compartment for the four fingers shall be cut from one piece of canvas.)	-
Cl.4.3.3.5 ( The thumb shall be made with the two sides placed inside and stitched with a row of stitches. The thumb thus formed shall be attached to the palm through the cut hole and secured by two rows of stitches.)	-
Cl.4.3.3.6 (The joint at the palm and the thumb shall be reinforced by the same leather material and stitched by two rows of stitches as shown in Fig. 3.)	-
Cl.4.3.3.7 ( The back portion made of canvas shall be secured with the corresponding palm piece made of leather by two rows of stitches with the edges of both the leather and canvas placed inside.)	-
Cl.4.3.3.8 ( The entire palm portion may be lined with canvas of the same quality as used for the back, if required by the purchaser.)	-
Cl.4.3.3.9 (The reinforcement piece shall be placed flesh side out and secured by four rows of stitches.)	-
Cl.4.3.3.10 (The cuff portion shall be made from one piece of canvas, the side edges being stitched together with two rows of stitches with the ends placed inside.)	-
Cl.4.3.3.11 ( The cuff thus formed shall be secured to the hand part by two rows of stitches all along their edges and turned over subsequently.The bottom edges of the cuff shall be hemmed. 6.0 mm with the raw edge properly,turned in.)	-
Cl.4.3.3.12 ( The mittens shall be machine stitched.)	-
Cl.4.3.3.13 ( The number of stitches for all stitchings shall be 6 to 8 stitches per 25 mm)	-
Cl.4.3.3.14 ( All loose ends of stitching threads shall be securely fastened.)	-
Cl.4.3.3.15 (workmanship and finish, and in all other respects not defined in this standard, the mittens shall conform to the approved sample.)	-

-
except shrinkage temperature test of RM, Length in m/Kg

231

IS 781 (1984)

Specification for cast copper alloy screw down bib taps and stop valves for water services (Third Revision)

For all sizes except for the tests mentioned in remarks

Rs.2700/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 3 (Nominal Size)	-
Cl 5 (Dimensions & Tolerances)	-
Cl 6.1 (CONSTRUCTION AND WORKMANSHIP)	-
Cl 6.3 (CONSTRUCTION AND WORKMANSHIP)	-
Cl 6.4 (CONSTRUCTION AND WORKMANSHIP)	-
Cl 6.5 (CONSTRUCTION AND WORKMANSHIP)	-
Cl 6.7 (CONSTRUCTION AND WORKMANSHIP)	-
Cl 6.8 (CONSTRUCTION AND WORKMANSHIP)	-
Cl 6.11 (CONSTRUCTION AND WORKMANSHIP)	-
Cl 8 (Finish)	-
Clause 4.1, Table-1 (Cast Brass Grade DCB - 2 of IS 1264 : 1981, Die Casting, Cu)	-
Clause 4.1, Table-1 (Cast Brass LCB-2 of IS 292 1983,Ingots, Cu + Ni)	-
Clause 4.1, Table-1 (Cast Brass Grade DCB - 2 of IS 1264 : 1981, Die Casting, Ni)	-
Clause 4.1, Table-1 (Cast Brass LCB-2 of IS 292 1983,Ingots, Sn)	-
Clause 4.1, Table-1 (Cast Brass Grade DCB - 2 of IS 1264 : 1981, Die Casting, Sn)	-
Clause 4.1, Table-1 (Cast Brass LCB-2 of IS 292 1983,Ingots, Pb)	-
Clause 4.1, Table-1 (Cast Brass Grade DCB - 2 of IS 1264 : 1981, Die Casting, Pb)	-
Clause 4.1, Table-1 (Cast Brass LCB-2 of IS 292 1983,Ingots, Fe)	-
Clause 4.1, Table-1 (Cast Brass Grade DCB - 2 of IS 1264 : 1981, Die Casting, Fe)	-
Clause 4.1, Table-1 (Cast Brass LCB-2 of IS 292 1983,Ingots, Al)	-
Clause 4.1, Table-1 (Cast Brass Grade DCB - 2 of IS 1264 : 1981, Die Casting, Mn)	-
Clause 4.1, Table-1 (Cast Brass Grade DCB - 2 of IS 1264 : 1981, Die Casting, Si)	-
Clause 4.1, Table-1 (Cast Brass LCB-2 of IS 292 1983,Ingots, Zn)	-
Clause 4.1, Table-1 (Cast Brass Grade DCB - 2 of IS 1264 : 1981, Die Casting, Zn)	-
Clause 4.1, Table-1 (Cast Brass Grade DCB - 2 of IS 1264 : 1981, Die Casting, Total imporities (excludig Ni + Pb + Al))	-
Clause 4.1, Table-1 (Leaded In Tin Bronze ,LTB-2 of IS 318, Sb)	-
Clause 4.1, Table-1 (Grade HT 1 of IS 320 : 1980, Sb)	-

-
Mech: Except hydraulic test, thread measurement

232

IS 15658 (2006)

Precast concrete blocks for paving - Specification

Rs.15940/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1.2 (Physical requirement)	-
6.2.1 & 7.1 (VISUAL INSPECTION)	-
B-1.3.1 (MEAN INDIVIDUAL WIDTH (of all eight test specimens), W)	-
B-5 (AVERAGE WIDTH (Average for eight test specimens), W)	-
B-1.3.1 (MEAN INDIVIDUAL LENGTH (of all eight test specimens), L)	-
B-5 (AVERAGE LENGTH (Average for eight test specimens), L)	-
Table 1 (MINIMUM PAVER BLOCK THICKNESS)	-
B-1.3.2 (MEAN INDIVIDUAL THICKNESS (of all eight test specimens), T)	-
B-1.3.3 (INDIVIDUAL ASPECT RATIO (L/T) (of all eight test specimens))	-
B-5 (AVERAGE ASPECT RATIO (L/T) (for eight test specimens))	-
B-2.3 (INDIVIDUAL ARRIS/CHAMFER (of all eight test specimens))	-
B-5 (AVERAGE ARRIS/CHAMFER (for eight test specimens))	-
B-5 (INDIVIDUAL PLAN AREA, ASP (of all eight test specimens) )	-
B-5 (AVERAGE PLAN AREA, ASP (for eight test specimens))	-
B-5 (INDIVIDUAL WEARING FACE AREA, Asw (of all eight test specimens))	-
B-5 (AVERAGE WEARING FACE AREA, Asw (for eight test specimens))	-
B- 4.3 (MEAN INDIVIDUAL SQUARENESS (of all eight test specimens) )	-
B-5 (AVERAGE SQUARENESS (for eight test specimens))	-
6.2.3 (THICKNESS OF WEARING LAYER, if the sample is Double Layered (for eight test specimens))	-
6.2.4 (WATER ABSORPTION TEST (Average for three test specimens))	-
6.2.4 (WATER ABSORPTION TEST (Average for three test specimens))	-
6.2.6 (ABRASION RESISTANCE, Dry Condition (For all eight test specimens))	-
6.2.6 (ABRASION RESISTANCE, Dry Condition (For all eight test specimens))	-
6.2.6 (ABRASION RESISTANCE, Wet Condition (For all eight test specimens))	-
6.2.6 (ABRASION RESISTANCE, Wet Condition (For all eight test specimens))	-

-
40 pcs Exclusion Except Freeze thaw durability test

233

IS 14246 (2024)

CONTINUOUSLY PRE-PAINTED GALVANIZED STEEL SHEETS AND STRIPS - SPECIFICATION Second Revision

For all classes except for the tests mentioned in remarks

4700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-4.1 (Steel Base)	-
As per Cl.4.1 (Carbon)	-
As per Cl.4.1 (Sulphur)	-
As per Cl.4.1 (Phosphorus)	-
As per Cl.4.1 (Manganese)	-
As per Cl.4.1 (Silicon)	-
Cl-4.1 (Steel Base)	-
As per Cl.4.1 (Titanium)	-
As per Cl.4.1 (Aluminium)	-
As per Cl.4.1 (Nitrogen)	-
As per Cl.4.1 (Copper)	-
As per Cl.4.1 (Niobium)	-
As per Cl.4.1 (Vanadium)	-
As per Cl.4.1 (Boron)	-
Cl-7.3.1 (Gloss)	-

-
Mech- Except salt spray test. Declaration w.r.t requirement and direction of measurement for gloss test (7.3) is required. Base metal to be declared (for test facilities see referred IS for Base Metal)

234

IS 4270 (2001)

Steel tubes used for water wells specification (Third Revision)

For all sizes except for the tests mentioned in remarks

Rs.7500/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 6 (Tensile Test & Flattening Test)	-
Cl 7 (Outer Diameter, Thickness, Mass & Straightness)	-
Cl 9 (Pipe ends, Angle of bevel & Root Face )	-
Cl 12 (Bituminous Coating & Galvanizing )	-
Cl 14 (Workmanship)	-
5.2 (sulphur)	-
5.2 (phosphorus)	-

-
Except Flattening above 300mm NB, Alignment , Hydrostatic , Thread dimension, Chem- complete

235

IS 4454 : Part 2 (2001)

Steel wire for mechanical springs - Specification february 2001: Part 2 oil hardened and tempered steel wire (Second Revision)

For all sizes except tests mentioned in remarks

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (Workmanship)	-
Cl 9 (Diameter & Difference Between Two Reading On Any Two Diameters)	-
7.1, 7.2 (carbon)	-
7.1, 7.2 (sulphur)	-
7.1, 7.2 (phosphorus)	-
7.1, 7.2 (manganese)	-
7.1, 7.2 (silicon )	-
7.1, 7.2 (copper)	-
7.1, 7.2 (Chromium)	-
Cl 10 (Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test, Decarburization Test, Coating and Surface Finish & Eddy Current Test)	-
7.1, 7.2 (Vanadium)	-

-
Facility not available for Deep Etch, Eddy current

236

IS 11226 (1993)

Leather safety footwear having direct moulded rubber sole specification (First Revision)

For all types

Rs. 26520/- excluding adhesion test on mould. View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (REQUIREMENTS)	-
5.2.5 (Materials)	-
5.2.6 (Materials)	-
5.2.6.1 (Materials)	-
5.2.6.2 (Materials)	-
5.2.6.3 (Materials)	-
5.2.7 (Materials)	-
5.2.8 (Materials)	-
5.2.9 (Materials)	-
5.2.10 (Materials)	-
5.2.11 (Materials)	-
5.2.11.1 (Materials)	-
5.2.11.2 (Materials)	-
5.2.11.3 (Materials)	-
5.3 (Components)	-
5.4 ( Manufacture )	-
5.4.1 ( Manufacture )	-
5.4.8 (Workmanship and Finish)	-
5.5 (Mass)	-
5.6 (Performance Test)	-
5.2.9 (Materials)	-

-
Mech: Complete

237

IS 13592 (2013)

Unplasticized Polyvinyl Chloride (PVC-U) Pipes for Soil and Waste Discharge System Inside and Outside Buiildings Including Ventilation and Rainwater System

For all sizes except for the tests mentioned in remarks

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.5 (Surface colour of the pipes shall be dark shade of grey)	-
Cl.7.1 (Mean out side Diameter (For less than or equal to 40 mm- Average of 8 , For higher diameters up to 110 mm average of 6))	-
Cl.7.1 (Wall thickness "minimum,maximum" (Take 8 reading))	-
Cl.7.1 (Mean out side Diameter (For less than or equal to 40 mm- Average of 8 , For higher diameters up to 110 mm average of 6))	-
Cl.7.2 (Pipes shall be supplied in nominal lengths of 2, 3, 4 or 6 metres either plain or with socket for solvent cementing/grooved socket. Tolerances on specified length shall be + 10 mm and – 0 mm.The nominal length of the pipe with socket for solvent cementing/grooved socket shall be as given in Fig. 1.)	-
Cl.7.3.1 (Minimum wall thickness of socket on pipes shall be as given in Table 2 read with Fig. 2 and Fig. 3.)	-
Cl.7.3.2 (Dimensions of sockets for solvent cementing and grooved sockets of pipes shall be as given in Tables 3 and 4 respectively, read with Fig. 2 and 3.)	-
Cl.8.1 (The internal and external surface of the pipes shall be smooth and clean, and free from grooving and other defects. The end shall be clearly cut and shall be square with the axis of the pipe. The end may be chamfered on the plain side.)	-
Cl.8.2 (When tested by the method described in IS 12235 (Part 5), a length of pipe sample of 200 ± 20 mm shall not alter in length by more than 5 percent. In the case of socket ended pipes, this test shall be carried out on the plain portion of pipe taken at least 100 mm away from the root of the socket.)	-
Cl8.3 (This test shall be carried out for socket end pipes only. When tested by the method described in IS 12235 (Part 6), the test specimens shall not show blisters, excessive delamination or cracking or signs of weld line splitting.)	-
Cl.8.4 (When determined in accordance with IS 12235 (Part 2), the vicat softening temperature of the specimen shall not be less than 79°C.)	-
Cl.8.5 (After the required period of exposure, the tensile strengths of two samples when tested as per IS 12235 (Part 13) shall not show difference of more than 20 percent of their initial tensile strengths)	-
Cl.10.1 (When tested by method prescribed in IS 12235 (Part 9),the pipe shall have a true impact rate of not more than 10 percent. Mass of striker and height of fall shall be as per Annex A.)	-
Cl.10.2 (When determined in accordance with the method described in IS 12235 (Part 13), the tensile strength at break shall not be less than 45 MPa.)	-
Cl.10.3 (The axial shrinkage shall not exceed 2 percent when determined in accordance with Annex B.)	-
Cl.7.1 (Outside Diameter at any point (Take 8 reading reported minimum, maximum))	-
Cl.7.1 (Wall thickness "minimum,maximum" (Take 8 reading))	-
Cl.7.3.1 (Minimum wall thickness of socket on pipes shall be as given in Table 2 read with Fig. 2 and Fig. 3.)	-
Cl. 12, IS 12235 Part 11 (Resistance to Di-Chloro-Methane)	-
Cl. 9, IS 12235 Part 7 (Resistance to Sulphuric Acid)	-
Cl 8.6 (Effect on Water Lead (first extraction))	-
Cl 8.6 (Effect on Water Lead (third extraction))	-
Cl 8.6 (Effect on Water Dialkyl tin C4 and higher homologues(measuredas tin )(third extraction ))	-
Cl 8.6 (Effect on Water Cadmium (mean of first extraction, second extraction and third extraction))	-
Cl 8.6 (Effect on Water Mercury (mean of first extraction, second extraction and third extraction))	-
CL 7.3 (Socket length (Take 4 reading & minimum will be reported))	-
CL 7.3.1 (Socket wall Thickness For S2 and S3 (Take 4 reading and average will be reported))	-
CL 7.3.2 grooved sockets (Length of beading and Neck A (Take 4 reading & Maximum will be reported))	-
CL 7.3.2 grooved sockets (Neck of Socket B (Take 4 reading & minimum, will be reported))	-
CL 7.3.2 grooved sockets (Length beyond beading C (Take 4 reading & minimum will be reported))	-
Cl.7.1 (Mean out side Diameter (For less than or equal to 40 mm- Average of 8 , For higher diameters up to 110 mm average of 6))	-

-
Chemical: All except Effect on Water which is for Pipes above 60 mm Nominal dia and except for the requirement of 'Other Toxic Substances such a di-n-octyl Tin -s-s bis iso-octyl mercapto acetate' and 'butyl stearate'; Mech- All except HST.

238

IS 8329 (2000)

Centrifugally cast (Spun) ductile iron pressure pipes for water, gas and sewage - Specification (Third Revision)

For all sizes

Rs.7800/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 10 (Hardness & Tensile Test)	-
Cl 13 (Length, Diameter, Wall Thickness & Ovality)	-
Cl 13 (Length, Diameter, Wall Thickness & Ovality)	-
Cl 13 (Length, Diameter, Wall Thickness & Ovality)	-

-
Hydrostatic test Required Cut pc for coating, Cut potion for dimension, cement lining, prepared test pc for tensile, hardness

239

IS 14968 (2015)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packing 50 Kg/25 kg sugar – Specification (first revision)

14300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.2 and Table 1 x (Ash content )	-
4.3.1 (Bottom Seam)	-
4.3.1 (The two rows of stitches shall be separated from each other)	-
4.3.1 ( The outer stitch)	-
4.3.1 (stitches/dm)	-
4.3.2 (Mouth)	-
4.5 and Table 1 i (Capacity)	-
5.2 and Table 1 ii a (Dimensions Inside Length)	-
5.2 and Table 1 ii b (Dimensions Inside Width)	-
5.2 and Table 1 iii (Ends per dm )	-
5.2 and Table 1 iv (Picks per dm )	-
5.1 and Table 1 v a (Mass of unlaminated sack IS 1964)	-
5.1 and Table 1 v b (Mass of unlaminated sack with liner )	-
5.2 and Table 1 vi a (Average breaking strength of fabric Lengthwise IS 1969 (Part 1))	-
5.2 and Table 1 vi b (Average breaking strength of fabric Widthwise IS 1969 (Part 1))	-
5.2 and Table 1 vi (Breaking strength of bottom seam IS 9030 )	-
5.2 and Table 1 viii a (Elongation at break of fabric Lengthwise IS 1969 (Part 1))	-
5.2 and Table 1 viii b (Elongation at break of fabric Widthwise IS 1969 (Part 1))	-
5.2 and Table 1 ix (Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-

-
Complete

240

IS 14252 (2015)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sack for filling sand – Specification (second revision)

13500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.3 (Tying Cord)	-
3.4.1 (Seam)	-
4.1 and Table 1 i a (Dimensions Outside Length)	-
4.1 and Table 1 i b (Dimensions Outside Width)	-
4.1 and Table 1 ii (Ends per dm )	-
4.1 and Table 1 iii (Picks per dm )	-
4.2 and Table 1 iv (Mass of sack )	-
4.1 and Table 1 v a (Average breaking strength of fabric Warpway )	-
4.1 and Table 1 v b (Average breaking strength of fabric Weftway )	-
4.1 and Table 1 vi (Average Breaking strength of bottom seam )	-
4.1 and Table 1 viii (Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-

-
Complete

Bureau of Indian Standards

The National Standards Body of India

BIS, Eastern Regional Laboratory (ERL)

(1) Annex Building & Sample-Cell: Bureau of Indian Standards, P-230, CIT Scheme, VII- M, Block-W,Kankurgachi,Kolkata-700054 (2) Main building: 1/14, CIT Scheme VII M, VIP Road, Kankurgachi,Kolkata-700054, Kolkata, Kolkata, West Bengal, 700054

- sample.erol@bis.gov.in

Scope List