BIS - LIMS (Laboratory Information Management System)

IDMA LABORATORIES LIMITED

PLOT NO. 391 INDUSTRIAL AREA PHASE 1, PANCHKULA, Panchkula, Haryana, 134113

9888002607 testing@idmagroup.co.in

Scope List

Reset

403 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

271

IS 9359 (1995)

Pesticide - Phorate G encapsulated - Specification

5820 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2.1(Physical -Description)	-	600	NA
3.2.2(Physical - Sieving Requiremenr)	-	800	NA
3.2.3(Dust)	-	800	NA
3.2.4.1(Encapsulation- % of declared nominal active ingredient in remnants.)	-	1500	NA
3.2.5(Moisture Content)	-	1000	NA
3.3.1(Phorate Content)	-	1500	NA
3.3.2(Acidity)	-	800	NA
3.2.4.2(Encapsulation- The active ingredient in the water (%, by Mass))	-	1500	NA

Complete

31 Dec, 2026

Included w.e.f. 05-02-2018

272

IS 14309 (1995)

Blended edible vegetable oils specification

7700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Table-1(Moisture and volatile matter percent by mass, Max type1)	-	1000	NA
Table-1(Acid value, mx type 1)	-	800	NA
Table-1(Unsaponifiable matter, percent by mass, MaX type1)	-	800	NA
Table-1(Flash point, Pen&y-Martens type1)	-	800	NA
Table-1(Moisture and volatile matter percent by mass, Max type2)	-	0	As above
Table-1(Acid value, mx type2)	-	0	As above
Table-1(Unsaponifiable matter, percent by mass, MaX type2)	-	0	As above
Table-1(Moisture and volatile matter percent by mass, Max type 3)	-	0	As above
Table-1(Acid value, mx type 3)	-	0	As above
Table-1(Unsaponifiable matter, percent by mass, MaX type3)	-	0	As above
Table-1(Flash point, Pen&y-Martens type3 )	-	0	As above
Table-1(Flash point, Pen&y-Martens ,type 2)	-	0	As above

Complete

31 Dec, 2026

Included w.e.f. 05-02-2018

273

IS 14509 (1997)

Lambda - Cyhalothrin, technical - Specification

3780 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 3.1()	-	180	NA
Clause 3.2 Table 1 S.No. i)(Lambda Cyhalothrin Content - IS 14509)	-	1800	NA
Clause 3.2 Table 1 S.No. ii)(Moisture Content - IS 6940)	-	1000	NA
Clause 3.2 Table 1 S.No. iii)(Acidity (as H2SO4) - IS 6940)	-	800	NA

Complete

31 Dec, 2026

Included w.e.f. 05-02-2018

274

IS 14551 (1998)

Thiophanate methyl, technical - Specificaiton

4500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Description)	-	500	NA
Table 1 (i), cl.3.2(Thiophanate methyl content)	-	1500	NA
Table 1 (ii), cl.3.2(Moisture content)	-	800	NA
Table 1 (iii), cl.3.2(Acidity)	-	800	NA
Table 1 (iv), cl.3.2(Material insoluble in acetone)	-	900	NA

Complete

31 Dec, 2026

Included w.e.f. 05-02-2018

275

IS 14552 (1998)

Thiophanatemethyl, WP specification

5200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2(Description)	-	400	NA
3.3 Table 1 i(Thiophanate methyl content )	-	1600	NA
3.3 Table 1 ii(Material passing through 75 micron IS sieve)	-	800	NA
3.3 Table 1 iii(Suspensibility)	-	1200	NA
3.3 Table 1 iv(Acidity/Alkalinity)	-	600	NA
3.3 Table 1 v(Wettability)	-	600	NA

Complete

31 Dec, 2026

Included w.e.f. 05-02-2018

276

IS 432 : Part 2 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 2 Hard-Drawn Steel Wire

5600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4.1(Workmanship)	-	200	NA
Cl 5 & 6(Diameter)	-	200	NA
Cl 7(UTM)	-	1000	NA
Cl 8.3(Bending To Both Side At 90°, Then Straight)	-	900	NA
Cl 7(UTM)	-	500	NA
Cl 7(UTM)	-	500	NA
Clause 3.1.1(Sulphur)	-	700	NA
Clause 3.1.1(Phosphorus)	-	700	NA
Clause 3(Nitrogen)	-	700	NA
Clause 7.1(Ultimate Tensile Stress)	-	0	Testing charges already mentioned above
Clause 7.1(Proof Stress (0.2 percent ))	-	0	Testing charges already mentioned above
Clause 7.1(Total Elongation over a gauge length of 8 D Where D is the dia of wire)	-	0	Testing charges already mentioned above
Cl 8.3(Bending To Both Side At 90°, Then Straight)	-	0	Testing charges for Nominal Size are Rs. 200/-

Complete

31 Dec, 2026

277

IS 432 : Part 1 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 1 Mild Steel and Medium Tensile Steel Bars

3100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5.1(Workmanship)	-	150	NA
Cl 6.2(Diameter & Ovality)	-	0	Parameter covered under Clause 6.1, Size.
Cl 8.2(Bend test)	-	300	NA
Cl 6.2(Weight)	-	100	NA
Cl 8.1(ultimate tensile stress, yield stress and percentage elongation)	-	800	NA
Cl 9.3(Press)	-	0	Testing charges already mentioned above Rs. 300/-
Cl 8(Physical Requirements)	-	0	Testing charges already mentioned above Rs. 800/-
Clause -4, 4.1(SULPHUR)	-	200	NA
Clause -4, 4.1(PHOSPHURS)	-	200	NA
Clause -4, 4.1(SILICON)	-	400	NA
Clause -4, 4.1(MANGANESE)	-	200	NA
Clause -4, 4.1( CARBON)	-	200	NA
Clause -4, 4.1(NITROGEN)	-	200	NA
Clause 6.1(Size)	-	150	NA
Clause 9.3(Bend test)	-	0	Testing charges already mentioned above Rs. 300/-
Clause 8.1(Yield Stress)	-	800	NA
Clause 8.1(Elongation)	-	800	ok
8.1 & 9.2(Yield Strength - IS: 1608 (P1))	-	0	Testing charges already mentioned above Rs. 800/-
8.1 & 9.2(Elongation on SoA 5.65mm GL - IS: 1608 (P1))	-	0	Testing charges already mentioned above Rs. 800/-
Clause 5.1(Freedom from Defect)	-	0	Testing charges already mentioned above Rs. 150/-
Clause 6.2(Mass)	-	0	Testing charges already mentioned above Rs. 100/-
Clause -4, 4.1(Chromium)	-	400	NA
Clause -4, 4.1(Molybdenum)	-	400	NA
Clause -4, 4.2(VANADIUM)	-	400	NA
Clause 4(Copper)	-	200	NA
Clause -4, 4.1(Nickel)	-	200	NA
Clause -4, 4.3(TITANIUM)	-	200	NA
Clause -4, 4.1( ALUMINIUM)	-	200	NA
Clause -4, 4.1(NIOBIUM)	-	200	NA
Clause 4(Carbon Equivalent)	-	200	NA
Clause 4(Boron)	-	200	NA

Complete

31 Dec, 2026

278

IS 15138 (2010)

Textiles – Jute bags for packing 50 kg sugar – Specification (first revision)

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5,5.1,5.2 Table 1,i) a) Cl.8.3.2 of IS 9113 Table A / B / C( Outside length )	-	300	OK
5,5.1,5.2 Table 1,i) b) Cl.8.3.2 of IS 9113 Table A / B / C(Outside width)	-	300	OK
5,5.1,5.2 Table 1,ii) Cl.8.4.2 of IS 9113 Table A / B / C(Ends/dm)	-	300	OK
5,5.1,5.2 Table 1,iii) Cl.8.4.2 of IS 9113 Table A / B / C(Picks/dm)	-	300	OK
5,5.1,5.2 Table 1,iv) Cl.8.5.2 of IS 9113 Table A / B / C(Corrected mass per bag)	-	300	OK
5,5.1,5.2 Table 1,v) a) Cl.8.6.2 of IS 9113 Table A / B / C(Average breaking load of sacking (ravelled strip method, 5.0 cm × 20.0 cm), Min, N (kgf) Warpway:)	-	400	OK
5,5.1,5.2 Table 1,v) b) Cl.8.6.2 of IS 9113 Table A / B / C(Average breaking load of sacking (ravelled stripmethod, 5.0 cm × 20.0 cm), Min, N (kgf) Weftway :)	-	400	NA
5,5.1,5.2 Table 1,vi) a) Cl.8.7 of IS 9113 Table A / B / C( Average breaking load of sacking (ravelled stripmethod, 5.0 cm × 20.0 cm), Min, N (kgf) Warpway:)	-	400	OK
5,5.1,5.2 Table 1,vi) b) Cl.8.7 of IS 9113 Table A / B / C( Average breaking load of sacking (ravelled stripmethod, 5.0 cm × 20.0 cm), Min, N (kgf) Weftway :)	-	400	OK
5,5.1,5.2 Table 1,vii)a) Cl.8.2 of IS 9113 Table A / B / C(Moisture regain)	-	300	OK
5,5.1,5.2 Table 1,vii)b) Table A / B / C(Contract moisture regain)	-	350	OK
4.2 IS 9113(Seam )	-	300	OK
4.3 IS 9113(Hemming at the Mouth )	-	200	OK
4.4 Annex B(Freedom from Defects)	-	300	OK
4.1(Fabric)	-	200	Weave of Fabric
4.5 IS 10146(Liner)	-	1000	Thickness of Liner & Overall Migration Rs 1000/- And Rs 300/- for missing parameter GSM under cl. no. 4.4

Complete

31 Dec, 2026

Included w.e.f. 05-02-2018

279

IS 14968 (2015)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packing 50 Kg/25 kg sugar – Specification (first revision)

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2 and Table 1 ii a(Dimensions Inside Length)	-	100	OK
5.2 and Table 1 ii b(Dimensions Inside Width)	-	100	OK
5.2 and Table 1 iii(Ends per dm )	-	100	OK
5.2 and Table 1 iv(Picks per dm )	-	100	OK
5.1 and Table 1 v a(Mass of unlaminated sack IS 1964)	-	200	OK
5.1 and Table 1 v b(Mass of unlaminated sack with liner )	-	200	OK
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise IS 1969 (Part 1))	-	150	OK
5.2 and Table 1 vi(Breaking strength of bottom seam IS 9030 )	-	300	OK
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise IS 1969 (Part 1))	-	100	OK
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	2000	OK
5.2 and Table 1 x(Ash content )	-	500	OK
4.3(Sacks)	-	100	OK
4.3.1(The two rows of stitches shall be separated from each other)	-	300	OK
4.3.1( The outer stitch)	-	0	Testing Charges mentioned above
4.4(Liner IS 10146 or IS 10910.)	-	600	Parameters under Liner: Length & Width of Liner, Bottom seam of Liner, Thickness of Liner & Visual inspection for defects.
4.3(Sacks)	-	0	OK
4.3.1(Bottom Seam)	-	300	OK
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	0	Testing Charges mentioned above
4.3.1(Stitches pass through a minimum of six layers of the fabric. )	-	0	Testing Charges mentioned above
4.3.1(stitches/dm)	-	0	Testing Charges mentioned above
4.3.2(Mouth)	-	200	OK
4.4(Mass of the loose liner )	-	0	Test Not Applicable
4.4(Width of the loose liner)	-	100	OK
4.4(Length of the line)	-	100	OK
4.4(Bottom seam of the loose liner)	-	100	OK
5.2 and Table 1 ii a(Dimensions Inside Length)	-	150	OK
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise IS 1969 (Part 1))	-	150	OK
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise IS 1969 (Part 1))	-	100	OK
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	0	testing charges mentioned above
5.2 and Table 1 x(Ash content )	-	0	testing charges mentioned above
4.1(Raw Material)	-	2000	Overall Migration test on Granules samples of HDPE or PP sample as per IS 10146 or IS 10910
4.2(Tapes – Width IS 6192 and IS 11197)	-	2700	Rs. 2700/- for each, testing of Tape sample (HDPE or PP) as per IS 6192 or IS 11197
4.2(Construction)	-	100	Mesh of the fabric
4.3.2(Mouth)	-	0	testing charges mentioned above
4.5 and Table 1 i(Capacity)	-	100	GSM Parameter is missing as per Clause no. 4.2, Testing charges = Rs. 200/-

Complete

31 Dec, 2026

Included w.e.f. 05-02-2018

280

IS 14887 (2014)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg food grains – Specification (first revision)

12300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.3.1(Bottom seam (IS 10789))	-	600	Testing Charges for missing clauses 3.3.2, Mouth = Rs 200/- 3.4, Capacity = Rs 200/-
4.2 and Table 1 ii(Dimensions )	-	500	OK
5.2 and Table 1 iii(Ends per dm )	-	150	OK
5.2 and Table 1 iv(Picks per dm )	-	150	OK
4.2 and Table 1 v(Mass of sack )	-	300	OK
4.2 and Table 1 vi(Average breaking strength of fabric )	-	1000	OK
4.2 and Table 1 vi(Breaking strength of bottom seam )	-	500	OK
4.2 and Table 1 viii(Elongation at break of fabric )	-	1000	OK
4.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	2100	OK
4.2 and Table 1 x(Ash content )	-	900	OK
3.1(Overall Migration)	-	2000	OK
3.2(Density)	-	600	OK
3.2(Tapes – Linear Density (IS 6192/IS 11197))	-	400	OK
3.2(Tapes – Tenacity (IS 6192/IS 11197))	-	400	OK
3.2(Tapes – Elongation at point of rupture (IS 6192/IS 11197))	-	400	OK
3.2(Tapes – Width and Thickness ( IS 6192/IS 11197))	-	400	OK
3.2(Tapes – Heat Shrinkage (HDPE) (Cl. 3.2 and IS 6192))	-	500	OK
3.2(Tapes – Dimensional stability (PP) (IS 11197))	-	500	Testing charges for Melt Flow Rate = Rs 600/-
3.3.1(Bottom seam (IS 10789))	-	0	testing charges mentioned above
4.2 and Table 1 ii(Dimensions )	-	0	testing charges mentioned above
5.2 and Table 1 iii(Ends per dm )	-	0	testing charges mentioned above
4.2 and Table 1 vi(Average breaking strength of fabric )	-	0	testing charges mentioned above
4.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	0	NA

Complete

31 Dec, 2026

Included w.e.f 28.05.2019

281

IS 12592 (2002)

Precast concrete manhole cover and frame - Specification (First Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.1(General)	-	600	Testing charges for Clear cover to reinforcement are Rs. 600/- Testing charges for Cover are Rs. 800/- Testing charges for Fixing of Manhole cover to frame are Rs. 1000/-
5.2(Dimensions of cover- Diameter)	-	800	NA
9.3 and Table and Annex C(Load Test)	-	4000	NA
3(Type/Shape of Cover)	-	600	NA
3(Grade)	-	0	Testing charges already mentioned above
5.2 and Table 1(Dimensions of Frame - A)	-	0	Testing charges already mentioned above
5.2 and Table 1(Dimensions of Frame - B)	-	0	Testing charges already mentioned above
5.2 and Table 1(Dimensions of Frame - C)	-	0	Testing charges already mentioned above
5.2 and Table 1(Dimensions of Frame - D)	-	0	Testing charges already mentioned above
5.2 and Table 1(Dimensions of Frame - E)	-	0	Testing charges already mentioned above
5.2 and Table 1(Dimensions of Frame - F)	-	0	Testing charges already mentioned above
8(LIFTING HOOKS)	-	800	NA
8(LIFTING HOOKS)	-	0	Testing charges already mentioned above
5.2(Clearance at top between the frame and the cover all round the periphery)	-	0	Testing charges already mentioned above
5.2(Suitable taper matching with taper given for the frame shall be provided to the periphery of the cover)	-	0	Testing charges already mentioned above
5.2(Top surface ofthe frame and cover is in level)	-	0	Testing charges already mentioned above
7.4.1(Edge Protection and Finishing - Frame)	-	800	NA
5.2 and Fig 1(Clear cover to reinforcement)	-	0	Testing charges already mentioned above
7.4.1(Edge Protection and Finishing - Frame)	-	0	Testing charges already mentioned above
7.4.1(Edge Protection and Finishing - Frame)	-	0	Testing charges already mentioned above

Complete

31 Dec, 2026

Included w.e.f. 05-02-2018

282

IS 12330 (1988)

Specificatioon for sulphate resisting Portland cement

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Fineness 4031 Part 2)	-	500	Total testing charges are Rs. 15000/- including Optional Test - Transvers Strength Testing charges Rs. 10000/- excluding Optional Test - Transvers Strength
5.2.1(Expansion by Le Chatelier- 4031 Part 3)	-	1200	NA
5.2.1.1(Expansion after aeration - 4031 Part 3)	-	0	NA
5.2.1(Expansion by Autoclave- 4031 Part 3)	-	0	Testing charges already mentioned above
5.2.1.1(Expansion after aeration- 4031 Part 3)	-	0	NA
5.3 a)(Setting Time Initial- 4031 Part 5)	-	700	NA
5.3 b)(Setting Time Final- 4031 Part 5)	-	0	Testing charges already mentioned above
5.4(Salphate Expansion (Optional))	-	1500	NA
5.5 i)(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	2500	NA
5.5 ii)(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	0	Testing charges already mentioned above
5.5 iii)(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	0	Testing charges already mentioned above
5.6(Transverse Strength - IS 4031 Part 8 (Optional))	-	5000	NA
4.1 - Table - 1 i(Ratio of percentage of lime to percentages of silica, alumina and iron oxide - Cl 4 of IS 4032:1985)	-	0	NA
4.1 - Table - 1 ii(Insoluble residue - Cl 4.10 of IS 4032:1985)	-	400	NA
4.1 - Table - 1 iii(Magnesia - Cl 4.8 of IS 4032:1985)	-	400	NA
4.1 - Table - 1 iv(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-	400	NA
4.1 - Table - 1 vii(Total loss on ignition - Cl 4.2 of IS 4032:1985)	-	400	NA
4.1 - Table - 1 v(Tricalcium aluminate (C3A) - Cl 4 of IS 4032:1985)	-	400	NA
4.1 - Table - 1 vi(Tetracalcium alumino ferrite phase plus twice the tricalcium aluminate ( C4AF + 2C3A ) - Cl 4 of IS 4032:1985)	-	400	NA

Complete

31 Dec, 2026

Included w.e.f. 05-02-2018

283

IS 10758 (1983)

Specification for de - Odourizing - Cum - Disinfectant fluids

6300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 3.1(Description)	-	400	NA
Cl. 3.2(Volatile matter)	-	500	NA
Cl. 3.2.1(Volatile matter (steam distillation))	-	1000	NA
Cl. 3.3(Stability after dilution(with artificial hard water))	-	300	NA
Cl. 3.4(Persistance of Odour)	-	300	NA
Cl. 3.5(Flash point(abel))	-	500	NA
Cl. 2.1(Germicidal Value)	-	3300	NA

Complete

31 Dec, 2026

Included w.e.f. 05-02-2018

284

IS 9873 : Part 3 (2020)

Safety of Toys Part 3 Migration of Certain Elements ( Third Revision )

4800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1 - Table 1(Antimony (Sb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	600	NA
4.1 - Table 1(Arsenic (As) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	600	NA
4.1 - Table 1(Barium (Ba) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	600	NA
4.1 - Table 1(Cadmium (Cd) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	600	NA
4.1 - Table 1(Chromium (Cr) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	600	NA
4.1 - Table 1(Lead (Pb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	600	NA
4.1 - Table 1(Mercury (Hg) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	600	NA
4.1 - Table 1(Selenium (Se) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	600	NA
4.1 - Table 1(Antimony (Sb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	0	NA
4.1 - Table 1(Arsenic (As) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	0	NA
4.1 - Table 1(Barium (Ba) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	0	NA
4.1 - Table 1(Cadmium (Cd) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	0	NA
4.1 - Table 1(Chromium (Cr) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	0	NA
4.1 - Table 1(Lead (Pb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	0	NA
4.1 - Table 1(Mercury (Hg) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	0	NA
4.1 - Table 1(Selenium (Se) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	0	NA

Complete

31 Dec, 2026

REVISED VERSION OF IS 9873(PT-3):2020 INCLUDED W.E.F. 11-11-2021

285

IS 9873 : Part 2 (2017)

Safety of toys: Part 2 flammability (Third Revision)

4000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.4-5.4(Toys intended to be entered by a child-rate of spread of flame)	-	4000		NA

Complete

31 Dec, 2026

Included w.e.f 28.05.2019

286

IS 9825 (2003)

Chlorine tablets - Specification (Second Revision)

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4.2(Description)	-	500	Total testing charges for Chlorine Tablets are Rs. 6000/- (including Rs. 3000/- for Shelf Life)
Cl.4.3(Available Chlorine (Annex A))	-	1200	NA
Cl.4.3(Size (Mass of tablet))	-	500	NA
Cl.4.4(Moisture (Annex B))	-	800	NA
Cl.4.4(Shelf Life (Annex A))	-	0	NA
Clause 5(Shelf Life)	-	3000	NA

Complete

31 Dec, 2026

Included w.e.f. 05-02-2018

287

IS 9103 (1999)

Specification for Concrete Admixtures -

23000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 9, Table- 2(Dry material content )	-	1000	NA
Clause 9, Table- 2(Ash content)	-	600	NA
Clause 9, Table- 2(Relative density)	-	500	NA
Clause 9, Table- 2(Chloride ion content)	-	500	NA
Clause 9, Table- 2( pH)	-	600	NA
Cl 4, Table 1A(Slump)	-	700	NA
Cl 4, Table 1 B(Flow, Loss of workability on satnding, Minimum compressive strength ( 7 Days,28 Days, 6 Month and 1 Year))	-	0	NA
Cl 4, Table 1A(Time of setting, allowable deviation from control sample hours)	-	1000	NA
Cl 4, Table 1A(Water Content, percent of control sample, Max)	-	700	NA
Cl 4, Table 1A(Compressive strength, percent of control sample, Min)	-	5000	NA
Cl 4, Table 1A(Length change, percent increase over control sample, Max)	-	2500	NA
Cl 4, Table 1A(Flexural strength, percent of control sample, Min)	-	2500	NA
Cl 4, Table 1A(Bleeding, percent increase over control sample, Max)	-	700	NA
Cl 4, Table 1A(Air content (%), Max, over control)	-	1000	NA
Cl 4, Table 1 B(Flow)	-	700	NA
Cl 4, Table 1 B(Loss of workability on standing)	-	0	NA
Cl 4, Table 1 B(Minimum compressive strength ( 7 Days,28 Days, 6 Month and 1 Year))	-	5000	NA
Cl 4, Table 1A(Loss of workability)	-	0	Testing charges already mentioned above
4, Table 1A(Flexural strength percent of control Sample 7 Day)	-	0	Testing charges already mentioned above
4, Table 1A(Flexural strength percent of control Sample 28 Day)	-	0	Testing charges already mentioned above
4, Table 1A(Flexural strength percent of control Sample 3 Day)	-	0	Testing charges already mentioned above
4, Table 1A(Length Change percent Increase over control Sample 28 Day)	-	0	Testing charges already mentioned above
4, Table 1A(Length Change percent Increase over control Sample 6 Month)	-	0	Testing charges already mentioned above
4, Table 1A(Length Change percent Increase over control Sample 1 year)	-	0	Testing charges already mentioned above
4, Table 1A(Compressive strength percent of control Sample 1 Day )	-	0	Testing charges already mentioned above
4, Table 1A(Compressive strength percent of control Sample 3 Days)	-	0	Testing charges already mentioned above
4, Table 1A(Compressive strength percent of control Sample 7 Days)	-	0	Testing charges already mentioned above
4, Table 1A(Compressive strength percent of control Sample 28 Days )	-	0	Testing charges already mentioned above
4, Table 1A(Compressive strength percent of control Sample 6 Months )	-	0	Testing charges already mentioned above
4, Table 1A(Compressive strength percent of control Sample 1 year )	-	0	Testing charges already mentioned above
Clause 4, Table 1B, SI no. (iii) (7 days minimum compressive strength, percent of control mix concrete)	-	0	Testing charges already mentioned above
4, Table 1B( minimum Compressive strength percent of control mix concrete 28 days)	-	0	Testing charges already mentioned above
4, Table 1B( minimum Compressive strength percent of control mix concrete 6 Months days)	-	0	Testing charges already mentioned above
4, Table 1B( minimum Compressive strength percent of control mix concrete 1 Year )	-	0	Testing charges already mentioned above
Clause 4, Table 1A, SI no. (iv) (1 year compressive strength, percent of control sample)	-	0	Testing charges already mentioned above
4, Table 1B( minimum Compressive strength percent of control mix concrete 7 days)	-	0	Testing charges already mentioned above

Complete

31 Dec, 2026

Included w.e.f. 05-02-2018

288

IS 8041 (1990)

Rapid hardening portland cement - Specific4tion (Second Revision)

13600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1 - Table - 1 ii(Ratio of percentage of alumina to that of iron oxide - Cl 4 of IS 4032:1985)	-	1600	Total testing charges including optional tests - Transverse strength are Rs. 15000/- Testing charges excluding optional tests - Transverse strength are Rs. 10000/-
5.1 - Table - 1 iii(Insoluble residue - Cl 4.10 of IS 4032:1985)	-	600	Testing charges for Progressive increase in strength as per clause no. 6.4.1 are Rs. 200/-
5.1 - Table - 1 iv(Magnesia - Cl 4.8 of IS 4032:1985)	-	600	NA
5.1 - Table - 1 vi(Total loss on ignition - Cl 4.2 of IS 4032:1985)	-	600	NA
6.1(Fineness 4031 Part 2)	-	500	NA
6.2.1(Expansion by Le Chatelier- 4031 Part 3)	-	1000	NA
6.2.1(Expansion by Autoclave- 4031 Part 3)	-	0	Testing charges already mentioned above
6.3 a)(Setting Time Initial- 4031 Part 5)	-	800	NA
6.3 b)(Setting Time Final- 4031 Part 5)	-	0	Testing charges already mentioned above
6.4 a)(Compressive Strength At 24 hrs ± 30 minutes - IS 4031 Part 6)	-	1500	NA
6.4 b)(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	0	Testing charges already mentioned above
6.5(Transverse Strength - IS 4031 Part 8 (Optional))	-	5000	NA
5.1 - Table - 1 v(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-	600	NA
5.1 - Table - 1 i(Ratio of percentage of lime to percentages of silica, alumina and iron oxide - Cl 4 of IS 4032:1985)	-	0	NA

Complete

31 Dec, 2026

Included w.e.f. 05-02-2018

289

IS 6909 (1990)

Supersulphated cement ? specification

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Insoluble residue - Cl 4.10 of IS 4032:1985)	-	800	Total testing charges including optional tests - Transverse strength are Rs. 15000/- Testing charges excluding optional tests - Transverse strength are Rs. 10000/-
5.1(Magnesium Oxide - Cl 4.8 of IS 4032:1985)	-	800	Testing charges for progressive increase in strength as per clause no. 6.6 are Rs. 500/-
5.1(Sulphuric anhydride - Cl 4.9 of IS 4032:1985)	-	800	NA
5.1(Sulphide sulphur - Cl 6.12 of IS 4032:1985)	-	800	NA
6.1(Fineness 4031 Part 2)	-	1000	NA
6.2(Soundness (cold expansion) by Le Chatelier- 4031 Part 3)	-	1000	NA
6.3 a)(Setting Time Initial- 4031 Part 5)	-	1000	NA
6.3 b)(Setting Time Final- 4031 Part 5)	-	0	Testing charges already mentioned above
6.4 a)(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	2500	NA
6.4 b)(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	0	NA
6.4 c)(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	0	Testing charges already mentioned above
6.5(Transverse Strength - IS 4031 Part 8 (Optional))	-	5000	NA
Clause 5.1(12423 : 1988)	-	800	NA

Complete

31 Dec, 2026

Included w.e.f. 05-02-2018

290

IS 6452 (1989)

High alumina cement for structural use - specification (First Revision)

5500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2(Fineness IS 4031(Part 2))	-	500	NA
4.3(Soundness, Le-Chate1ier expansion IS 4031(Part 3) )	-	500	NA
4.4(Setting Time ( by Vicat Apparatus ),Initial IS 4031(Part 5))	-	600	NA
4.4(Setting Time ( by Vicat Apparatus ), Final IS 4031(Part 5))	-	0	Testing charges already mentioned above
4.5(Compretsive Strenqth .24 hrs ± 30min IS 4031(Part 6))	-	2800	NA
4.5(Compretsive Strenqth .72 ± 1 hr IS 4031(Part 6))	-	0	Testing charges already mentioned above
4.1(Total alumina content (Al2O3) - Cl 4.6 of IS 4032:1985)	-	1100	0

Complete

31 Dec, 2026

Included w.e.f. 05-02-2018

291

IS 6006 (2014)

Uncoated stress relieved strand for prestressed concrete - Specification (Second Revision)

37000 View breakup
Rs. 6300/- excluding relaxation test, Rs. 30000/- including relaxation test

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4(Length )	-	600	Total testing charges are Rs. 37000/- including 1000 hrs Relaxation Test. Rs. 7000/- excluding Relaxation Test. Rs. 30000/- for 1000 hrs Relaxation test only. Rs. 10000/- for 100 hrs relaxation test only.
Cl 4(Joints)	-	600	NA
Cl 4(Butt Joint)	-	0	NA
Cl 4.5(Workmanship)	-	600	NA
Cl 5, Table 1(Diameter)	-	1000	NA
Cl 5, Table 1(Weight)	-	0	Testing charges already mentioned above at Cl 5, Table 1 (Diameter) are Rs. 1000/-
Cl 7.1(Tensile Test On UTM)	-	1000	NA
Cl 7.2(Tensile Test On UTM)	-	1000	NA
Cl 7.3(Tensile Test On UTM)	-	800	NA
Cl 7.4(Load )	-	10000	NA
Cl 4(Joints)	-	0	Already add in parameter
Cl 5(Weight)	-	0	Testing charges already mentioned above at Cl 5, Table 1 (Diameter) are Rs. 1000/-
Cl 7(Tensile Test On UTM)	-	0	Already add in parameter
Cl 7(Tensile Test On UTM)	-	0	Already add in parameter
Cl 7(Tensile Test On UTM)	-	0	Already add in parameter
Cl 7(Load )	-	30000	NA
Cl 5, Table 1(Diameter)	-	0	Testing charges already mentioned above at Cl 5, Table 1 (Diameter) are Rs. 1000/-
4.1.2(phosphorus)	-	600	NA
4.1.2(sulphur)	-	600	NA
Clause 4.1.3(Wire Description)	-	200	NA
Clause 4.2(Strand (Difference of center wire and surrounding wire))	-	0	NA
Clause 4.2(Forming of Strand)	-	0	NA
Clause 5.1, Table-1 (Nominal dia of Element Wire (Two - Wire Strand) )	-	0	Testing charges already mentioned above at Cl 5, Table 1 (Diameter) are Rs. 1000/-
Clause 5.1, Table-1 (Nominal Area of Strand (Two - Wire Strand) )	-	0	Testing charges already mentioned above at Cl 5, Table 1 (Diameter) are Rs. 1000/-
Clause 5.1, Table-1 (Nominal Mass of Strand (Two - Wire Strand) )	-	0	Testing charges already mentioned above at Cl 5, Table 1 (Diameter) are Rs. 1000/-
Clause 5.2, Table-1 (Nominal dia of Element Wire (Three - Wire Strand) )	-	0	Testing charges already mentioned above at Cl 5, Table 1 (Diameter) are Rs. 1000/-
Clause 5.2, Table-1 (Nominal Area of Strand (Three - Wire Strand) )	-	0	Testing charges already mentioned above at Cl 5, Table 1 (Diameter) are Rs. 1000/-
Clause 5.2, Table-1 (Nominal Mass of Strand (Three - Wire Strand) )	-	0	Testing charges already mentioned above at Cl 5, Table 1 (Diameter) are Rs. 1000/-
Clause 5.3, Table-2 (Nominal Diameter of Strand (Seven - Wire Strand) )	-	0	Testing charges already mentioned above at Cl 5, Table 1 (Diameter) are Rs. 1000/-
Clause 5.3, Table-2 (Nominal Area of Strand (Seven - Wire Strand) )	-	0	Testing charges already mentioned above at Cl 5, Table 1 (Diameter) are Rs. 1000/-
Clause 5.3, Table-2 (Nominal Mass of Strand (Seven - Wire Strand) )	-	0	Testing charges already mentioned above at Cl 5, Table 1 (Diameter) are Rs. 1000/-
Clause 7.4(Relaxation Stress (1000 h) )	-	0	Already add in parameter
Clause 7.4.1(Relaxation Stress (100 h) )	-	0	Already add in parameter

Complete

31 Dec, 2026

Included w.e.f 28.05.2019

292

IS 3812 (Part 1) (2013)

Pulverized fuel ash - Specification: Part 1 For use as pozzolana in cement, cement mortar and concrete

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 6.1, Table 1 - i(Silicon dioxide (SiO2) plus aluminium oxide (Al2O3) plus ironoxide (Fe2O3) - IS 1727)	-	1800	NA
Cl. 6.1, Table 1 - ii(Silicon dioxide (SiO2) - IS 1727)	-	0	Testing charges already mentioned above
Cl. 6.1, Table 1 - iii(Reactive Silica - Annex B)	-	600	NA
Cl. 6.1, Table 1 - iv(Magnesium oxide (MgO) - IS 1727)	-	500	NA
Cl. 6.1, Table 1 - v( Total sulphur as sulphur trioxide (SO3) - IS 1727)	-	500	NA
Cl. 6.1, Table 1 - vi( Available alkalis as equivalent sodium oxide (Na2O) - Annex C)	-	500	NA
Cl. 6.1, Table 1 - vii( Total Chlorides - IS 4032)	-	500	NA
Cl. 6.1, Table 1 - viii( Loss on ignition - IS 1727)	-	500	NA
Cl. 6.2(Moisture content of the fly ash when supplied in dry condition - Annex D)	-	400	NA
7.1-Table 2(i)(PHYSICAL REQUIREMENTS-Fineness)	-	500	NA
7.1-Table 2(ii)(PHYSICAL REQUIREMENTS-Particles retained on 45 micron IS sieve)	-	500	NA
7.1-Table 2(iii)(PHYSICAL REQUIREMENTS-Average compressive strength)	-	1600	0
7.1-Table 2(iv)(PHYSICAL REQUIREMENTS-Compressive strength at 28 days)	-	0	Testing charges already mentioned above
7.1-Table 2(v)(PHYSICAL REQUIREMENTS-Soundness by autoclave test )	-	800	NA
5.1, 7.1, table-2, iii(Lime reacitivity)	-	1500	Testing charges for Iron Oxide are Rs. 800/-

Complete

31 Dec, 2026

Included w.e.f. 05-02-2018

293

IS 3466 (1988)

Specification For Masonry Cement

9900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1 Table 1 i(Fineness IS : 4031:1988)	-	700	NA
3.1 Table 1 ii a(Setting Time ( by Vicat Apparatus ),Initial IS : 4031:1988)	-	600	NA
3.1 Table 1 ii b(Setting Time ( by Vicat Apparatus ), Final IS : 4031:1988)	-	0	Testing charges already mentioned above
3.1 Table 1 iii a(Soundness, Le-Chate1ier expansion IS 4031:1988)	-	600	NA
3.1 Table 1 iii b(Soundness, Autoclave expansion IS 4031:1988)	-	1200	NA
3.1 Table 1 v(Air Content IS 4031:1988)	-	1200	NA
3.1 Table 1 vi(Water Retention IS 4031:1988)	-	2100	NA
3.1 Table 1 iv (Compretsive Strenqth 7 days IS 4031:1988)	-	2500	NA
3.1 Table 1 iv (Compretsive Strenqth 28 days IS 4031:1988)	-	0	Testing charges already mentioned above
4( water soluble alkali content - Cl 9 of IS 4032:1985)	-	1000	NA

Complete

31 Dec, 2026

Included w.e.f. 05-02-2018

294

IS 2831 (2012)

Carbon steel cast billet ingots, billets, blooms and slabs for re-rolling into structural steel (Ordinary Quality) - Specification (Fourth Revision)

7300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 6.1, Table 1(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	NA
Cl. 6.1, Table 1(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	NA
Cl. 6.1, Table 1(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	NA
Cl. 6.1, Table 1(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	NA
Cl. 6.1, Table 1(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	NA
Cl. 6.1, Table 1(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	450	NA
Cl. 6.1, Table 1(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	450	NA
9( FREEDOM FROM DEFECTS)	-	300	NA
11 & 12(DIMENSIONS and Tolerances)	-	400	NA
Cl. 6.1, Table 1(Aluminium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	450	NA
Cl. 6.1, Table 1(Niobium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	450	NA
11(Dimensions)	-	0	Testing charges already mentioned above under Dimensions i.e. Rs. 400/-
10.2(Bend)	-	0	NA
10.3(Chamber)	-	0	NA
Cl. 6.1, Table 1(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	NA
Clause 6.1.1(IS 2831 : 2012)	-	0	Testing charges for Vanadium 450/- Testing Charges for Carbon Equivalent are Rs. 200/-
Clause 9.3(Bend)	-	350	NA
Clause 9.4(Camber)	-	300	NA
Cl. 6.1, Table 1(Titanium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	450	NA

Complete

31 Dec, 2026

Included w.e.f. 05-02-2018

295

IS 2830 (2012)

Carbon steel cast billet ingots, billets, blooms and slabs for re-rolling into steel for general structural purposes - Specification (Third Revision)

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 11(Length)	-	400	NA
Cl 9(Workmanship)	-	300	NA
Cl 10.2(Workmanship)	-	350	NA
Cl 10.3(Workmanship)	-	300	NA
6.1(Carbon %)	-	300	NA
6.1(Manganese %)	-	400	NA
6.1(Phosphorus %)	-	400	NA
6.1(Sulphur %)	-	300	NA
6.1( Copper %)	-	450	NA
6.1(Silicon %)	-	500	NA
6.1( Nb)	-	450	NA
6.1(V)	-	450	NA
6.1( Ti)	-	450	NA
6.1(Cr)	-	450	NA
6.1(Mo)	-	450	NA
6.1(Nitrogen%)	-	450	NA
6.1( Aluminium %)	-	450	NA
6.1(Ni)	-	450	NA
Cl 10.2(Press)	-	0	NA
Cl 10.3(Workmanship)	-	0	NA
Cl 11(Length, Width & Thickness)	-	0	Testing charges already mentioned above under Workmanship i.e. Rs. 400/-
Cl 11(Length, Width & Thickness)	-	0	Testing charges already mentioned above under Workmanship i.e. Rs. 400/-
Cl 10.2(Workmanship)	-	0	Testing charges already mentioned above
Cl 10.3(Workmanship)	-	0	Testing charges already mentioned above
Cl. 10.2(Bend)	-	0	Testing charges already mentioned above
Clause 10.3(Camber)	-	0	Testing charges already mentioned above
Clause 6.1(IS 2830 : 2012)	-	200	NA
5(Manufacture)	-	0	NA
6(Copper as Cu)	-	0	Testing charges already mentioned above
6.1( Nb)	-	0	Testing charges already mentioned above
6(Sulphur + Phosphorus)	-	0	NA
6(carbon equivalent (CE))	-	0	Testing charges already mentioned above

Complete

31 Dec, 2026

Included w.e.f. 05-02-2018

296

IS 2645 (2003)

Integral waterproofing compounds for cement mortar and concrete - Specification (Second Revision)

9500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 3.4(Chloride content)	-	1000	NA
Cl 3.1(The permeability of water in specimen Prepared with WPC shall be less than half the permeability of plain cement specimens. (i.e ; < 50 percent))	-	3500	NA
Cl 3.2(Initial & Final)	-	1000	NA
Cl 3.3(Compressive Strength, At 3days & 7 days)	-	4000	NA
Clause 3.2(Initial setting time of cement)	-	0	Testing charges already mentioned above
Clause 3.2(Final setting time of cement)	-	0	Testing charges already mentioned above
Clause 3.3(Compressive strength of cement mortar with waterproofing compound at 3 days (72 ± 1 h))	-	0	Testing charges already mentioned above
Clause 3.3(Compressive strength of cement mortar with waterproofing compound at 7 days (168 ± 2 h))	-	0	Testing charges already mentioned above

Complete

31 Dec, 2026

297

IS 1785 : Part 2 (1983)

Specification for plain hard drawn steel wire for prestressed concrete: Part 2 as - Drawn wire (First Revision)

4500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5.1(Diameter)	-	400	NA
Cl 6.1(Tensile Test On UTM)	-	800	NA
Cl 6.2(Tensile Test On UTM)	-	800	NA
Cl 6.3(Tensile Test On UTM)	-	800	NA
Cl 5.1.2(Weight)	-	200	NA
3.1.1(PHOSPHORUS)	-	500	NA
3.1.1(SULPHUR)	-	500	NA
Clause 3.3(Workmanship )	-	200	NA
Clause 3.4(Surface Finish)	-	200	NA
Clause 3.5(Weld joints)	-	200	NA
Clause 6.4(Uncoiling Of Wire)	-	200	Testing charges for freedom from surface defects are Rs. 200/-

Complete

31 Dec, 2026

298

IS 1341 (2018)

Steel Butt Hinges - Specification (Sixth Revision)

9500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1 Tables 2 to 9 (2)(Size of Hinge)	-	600	NA
5.1 Tables 2 to 9 (3)(Length A)	-	0	Testing charges already mentioned above 5.1 Tables 2 to 9 (2) (Size of Hinge) are Rs. 600/-
5.1 Tables 2 to 9 (4)(Breadth B)	-	0	Testing charges already mentioned above 5.1 Tables 2 to 9 (2) (Size of Hinge) are Rs. 600/-
5.1 Tables 2 to 9 (4)(Breadth B1)	-	0	Testing charges already mentioned above 5.1 Tables 2 to 9 (2) (Size of Hinge) are Rs. 600/-
5.1 Tables 2 to 9 (4)(Breadth B2)	-	0	Testing charges already mentioned above 5.1 Tables 2 to 9 (2) (Size of Hinge) are Rs. 600/-
5.1 Tables 2 to 9 (5)(Thickness of Flap C)	-	0	Testing charges already mentioned above 5.1 Tables 2 to 9 (2) (Size of Hinge) are Rs. 600/-
5.1 Tables 2 to 9 (6)(Diameter of Hinge Pin D)	-	0	Testing charges already mentioned above 5.1 Tables 2 to 9 (2) (Size of Hinge) are Rs. 600/-
5.1 Tables 2 to 9 (7)(Number of Knuckles)	-	0	Testing charges already mentioned above 5.1 Tables 2 to 9 (2) (Size of Hinge) are Rs. 600/-
5.1 Tables 2 to 9 (8)(Number of Screw Holes)	-	0	Testing charges already mentioned above 5.1 Tables 2 to 9 (2) (Size of Hinge) are Rs. 600/-
5.1 Tables 2 to 9 (9)(Holes for Screw No.)	-	0	Testing charges already mentioned above 5.1 Tables 2 to 9 (2) (Size of Hinge) are Rs. 600/-
6.1(General)	-	500	NA
6.2.1(Knuckles)	-	500	NA
6.3(Pins)	-	500	NA
6.4(Screw Holes)	-	500	NA
6.4.2(Position of Holes)	-	500	NA
7(Finish)	-	400	NA
6.4.2(X)	-	0	Testing charges already mentioned above 5.1 Tables 2 to 9 (2) (Size of Hinge) are Rs. 600/-
6.4.2(Y)	-	0	Testing charges already mentioned above 5.1 Tables 2 to 9 (2) (Size of Hinge) are Rs. 600/-
6.4.2(Z)	-	0	Testing charges already mentioned above 5.1 Tables 2 to 9 (2) (Size of Hinge) are Rs. 600/-
6.4.2.1(Position of Holes)	-	0	NA
Clause 4 Table 1(Carbon ( Flap))	-	200	NA
Clause 4 Table 1(Sulphur ( Flap))	-	200	NA
Clause 4 Table 1(Phosphorus ( Flap))	-	200	NA
Clause 4 Table 1(Manganese ( Flap))	-	300	NA
Clause 4 Table 1(Nitrogen ( Flap))	-	0	NA
Clause 4 Table 1(Carbon ( Pin))	-	200	NA
Clause 4 Table 1(Sulphur ( Pin))	-	200	NA
Clause 4 Table 1(Phosphorus ( Pin))	-	200	NA
Clause 4 Table 1(Manganese ( Pin))	-	300	NA
TABLE-1 (Clause-4)( CARBON)	-	0	NA
TABLE-1 (Clause-4)(SILICON)	-	300	Rs. 300/- each for Flap and Pin.
TABLE-1 (Clause-4)(MANGANESE)	-	0	NA
TABLE-1 (Clause-4)(SULPHUR)	-	0	NA
TABLE-1 (Clause-4)(PHOSPHURS)	-	0	NA
TABLE-1 (Clause-4)(Chromium)	-	300	Rs. 300/- each for Flap and Pin
TABLE-1 (Clause-4)(Molybdenum)	-	300	Rs. 300/- each for Flap and Pin
TABLE-1 (Clause-4)(VANADIUM)	-	300	Rs. 300/- each for Flap and Pin
TABLE-1 (Clause-4)(Nickel)	-	300	Rs. 300/- each for Flap and Pin

Complete

31 Dec, 2026

299

IS 1239 : Part 2 (2011)

Steel tubes, tubulars and other steel fittings - Specification: Part 2 steel pipe fittings (Fifth Revision)

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
14(WORKMANSHIP)	-	200	NA
8.1-Table 1( DIMENSIONS OF TUBULARS-Pieces )	-	50	NA
8.1-Table 1( DIMENSIONS OF TUBULARS-Pieces-Approximate Standard Length(A) )	-	0	Testing charges already mentioned above 8.1-Table 1 ( DIMENSIONS OF TUBULARS-Pieces( (Nominal Bore) are Rs. 50/-
8.2-Table-2( DIMENSIONS OF TUBULARS-Nipples-A )	-	100	NA
8.2-Table-2( DIMENSIONS OF TUBULARS-Nipples-B )	-	0	Testing charges already mentioned above 8.2-Table-2 ( DIMENSIONS OF TUBULARS-Nipples-A ) are Rs. 100/-
8.2-Table-2( DIMENSIONS OF TUBULARS-Nipples-C )	-	0	Testing charges already mentioned above 8.2-Table-2 ( DIMENSIONS OF TUBULARS-Nipples-A ) are Rs. 100/-
8.3.1-Table 3(DIMENSIONS OF TUBULARS-Longscrews (Connectors)-A)	-	100	NA
8.3.1-Table 3(DIMENSIONS OF TUBULARS-Longscrews (Connectors)-B)	-	0	Testing charges already mentioned above 8.3.1-Table 3 (DIMENSIONS OF TUBULARS-Long screws are Rs. 100/-
8.3.1-Table 3(DIMENSIONS OF TUBULARS-Longscrews (Connectors)-C)	-	0	Testing charges already mentioned above 8.3.1-Table 3 (DIMENSIONS OF TUBULARS-Long screws are Rs. 100/-
8.3.2(DIMENSIONS OF TUBULARS-Longscrews (Connectors))	-	0	Testing charges already mentioned above 8.3.1-Table 3 (DIMENSIONS OF TUBULARS-Long screws are Rs. 100/-
8.4.1 -Table 4(Bends and springs)	-	150	NA
8.4.1 -Table 4(Bends and springs-A)	-	0	Testing charges already mentioned above 8.4.1 -Table 4 (Bends and springs) are Rs. 150/-
8.4.1 -Table 4(Bends and springs-B)	-	0	Testing charges already mentioned above 8.4.1 -Table 4 (Bends and springs) are Rs. 150/-
8.4.1 -Table 4(Bends and springs-R)	-	0	Testing charges already mentioned above 8.4.1 -Table 4 (Bends and springs) are Rs. 150/-
8.4.1 -Table 4(Bends and springs-C)	-	0	Testing charges already mentioned above 8.4.1 -Table 4 (Bends and springs) are Rs. 150/-
8.4.1 -Table 4(Bends and springs-D)	-	0	Testing charges already mentioned above 8.4.1 -Table 4 (Bends and springs) are Rs. 150/-
8.4.1 -Table 4(Bends and springs-E)	-	0	Testing charges already mentioned above 8.4.1 -Table 4 (Bends and springs) are Rs. 150/-
8.5-Table 5( Return Bends-A)	-	150	NA
8.5-Table 5( Return Bends-B)	-	0	Testing charges already mentioned above 8.5-Table 5 ( Return Bends-B) are Rs. 150/-
8.5-Table 5( Return Bends)	-	0	Testing charges already mentioned above 8.5-Table 5 ( Return Bends-B) are Rs. 150/-
8.6 -Table 6(Sockets-A)	-	100	NA
8.6 -Table 6(Sockets-B)	-	0	Testing charges already mentioned above 8.6 -Table 6 (Sockets-A) are Rs. 100/-
8.6 -Table 6(Maximum Inside Diameter of Internal Parallel Thread)	-	0	Testing charges already mentioned above 8.6 -Table 6 (Sockets-A) are Rs. 100/-
9.1-Table 7(Dimensions of Screwed Ends of Fittings-D )	-	100	NA
9.1-Table 7(Dimensions of Screwed Ends of Fittings-E )	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 7(Dimensions of Screwed Ends of Fittings-d )	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 7(Dimensions of Screwed Ends of Fittings-Taper )	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 8 (Dimensions of Elbows, Tees and Crosses, Equal-A)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 9 (Dimensions of Elbows Reducing-A)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 9 (Dimensions of Elbows Reducing-B)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 10 (Dimensions of Tees, Reducing (on the Branch)-A)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 10 (Dimensions of Tees, Reducing (on the Branch)-B)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 11 (Dimensions of Tees, Reducing (on the Run and Branch, or on the Run Only)-A)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 11 (Dimensions of Tees, Reducing (on the Run and Branch, or on the Run Only)-B)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 12(Dimensions of Tees (Increasing on the Branch)-A)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 12(Dimensions of Tees (Increasing on the Branch)-B)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 13( Dimensions of Crosses, Reducing-A)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 13( Dimensions of Crosses, Reducing-B)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 14( Elbows, Tees and Crosses, Side Outlet, Equal-A)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 15( Dimensions of Elbows, Round, Male and Female, Equal-A)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 15( Dimensions of Elbows, Round, Male and Female, Equal-B)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 15( Dimensions of Elbows, Round, Male and Female, Equal-Minimum Bore of Male End)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 15( Dimensions of Elbows, Round, Male and Female, Equal-Maximum Bore of Male End)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 16( Dimensions of Elbows, Equal, 135°-A)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 17 (Dimensions of Y-Pieces, Female, Equal-A)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 18 (Dimensions of Socket, Reducing-A)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 19 (Dimensions of Caps-A)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 19 (Dimensions of Caps-T)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 20(Dimensions of Plug-Minimum Length of Thread for Basic Gauge)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 20(Dimensions of Plug-Minimum Length of Thread for Basic Gauge-S)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 20(Dimensions of Plug-Minimum Length of Thread for Basic Gauge-H)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 20(Dimensions of Plug-Minimum Length of Thread for Basic Gauge-D)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 20(Dimensions of Plug-Minimum Length of Thread for Basic Gauge-K)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 21 (Dimensions of Elbows, Tees and Crosses, Male, Equal-A)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 22(Dimensions of Y-Pieces and Angle Tees, Male, Equal-A )	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 22(Dimensions of Y-Pieces and Angle Tees, Male, Equal-B )	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 23( Dimensions of Twin Elbows and Sweep Tees, Male, Equal-A)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 23( Dimensions of Twin Elbows and Sweep Tees, Male, Equal-B)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 24(Dimensions of Socket Unions-A )	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 25 (Dimensions of Pipe Unions-A)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 26 (Dimensions of Union Bends-A )	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 26 (Dimensions of Union Bends-B )	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 27 (Dimensions of Hexagon Bushes-L)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 27 (Dimensions of Hexagon Bushes-T)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 27 (Dimensions of Hexagon Bushes-A)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 27 (Dimensions of Hexagon Bushes-B)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 28 (Dimensions of Nipples, Hexagon, Equal-L)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 28 (Dimensions of Nipples, Hexagon, Equal-T)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 28 (Dimensions of Nipples, Hexagon, Equal-A)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 28 (Dimensions of Nipples, Hexagon, Equal-C)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
9.1-Table 28 (Dimensions of Nipples, Hexagon, Equal-B)	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
11.1(a)(Internal hydraulic Pressure Test)	-	0	NA
11.2.1( Drift Expanding Test)	-	0	NA
11.2.2 (Taper Screw Plug Test)	-	0	NA
13 and as per IS 4736(UNIFORMITY OF ZINC COATING)	-	300	NA
13 and as per IS 4736(MASS OF ZINC COATING)	-	500	NA
7.1(Chemical Composition - Sulphur - Laddle Analysis IS 228)	-	1000	NA
7.1(Chemical Composition - Phosphorus - Laddle Analysis IS 228)	-	1000	NA
Clause 9.1, Table- 27(Normal Size (Internal Threads) (Dimensions of Hexagon Bushes) )	-	0	NA
Clause 9.1, Table- 27(Normal Size (External Threads) (Dimensions of Hexagon Bushes) )	-	0	NA
Clause 9.2.2 (Tolerance for alignment of threads )	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
Clause 9.2.3 (Threads tolerance )	-	0	Testing charges already mentioned above 9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D are Rs. 100/-
Clause 10(Joints )	-	100	NA
Clause 13.1.3 (Adhesion Test)	-	300	NA
Clause 8.3.3(Parallel threads )	-	100	NA

Complete

31 Dec, 2026

300

IS 1239 : Part 1 (2004)

Steel tubes, tubulars and other wrought steel fittings - Specification: Part 1 steel tubes (Sixth Revision)

8300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8(Outer Diameter, Thickness & Mass)	-	200	Testing charges for Elongation Test parameter (as per Clause no. 14.1.1) are Rs. 500/- Testing charges for Nominal Bore are Rs. 200/-
Cl 8(Outer Diameter, Thickness & Mass)	-	200	NA
Cl 8(Outer Diameter, Thickness & Mass)	-	200	NA
Cl 14(Tensile Test, Flattening Test & Bend Test)	-	1000	NA
Cl 14(Tensile Test, Flattening Test & Bend Test)	-	800	NA
Cl 14(Tensile Test, Flattening Test & Bend Test)	-	800	NA
Cl 15(Workmanship)	-	500	NA
Cl 10.1.1(Manufacturing )	-	0	NA
Clause 11.1(Random Length)	-	200	NA
Clause 11.2(Exact Length)	-	0	Testing charges are Rs. 200/- already mentioned above under Clause 11.1 Random Length
Clause 11.3(Approximate Length)	-	0	Testing charges are Rs. 200/- already mentioned above under Clause 11.1 Random Length
13.0(Leak Proof Test)	-	0	NA
7, 6.1.1(CARBON)	-	300	NA
7, 6.1.1(SILICON)	-	300	NA
7, 6.1.1(MANGANESE)	-	300	NA
7, 6.1.1(SULPHUR)	-	300	NA
7, 6.1.1(PHOSPHURS)	-	300	NA
12 AND AS PER IS 4736(MASS OF ZINC COATING)	-	700	NA
12 AND AS PER IS 4736(UNIFORMITY OF ZINC COATING)	-	0	Testing charges are Rs. 700/- already mentioned above under Clause 12 MASS OF ZINC COATING

Complete

31 Dec, 2026

Bureau of Indian Standards

The National Standards Body of India

IDMA LABORATORIES LIMITED

PLOT NO. 391 INDUSTRIAL AREA PHASE 1, PANCHKULA, Panchkula, Haryana, 134113

9888002607 testing@idmagroup.co.in

Scope List