BIS - LIMS (Laboratory Information Management System)

BIS, Northern Regional Laboratory (NRL)

B-69, Industrial Focal Point, Phase VII, Mohali, Mohali, S.A.S Nagar, Punjab, 160059

- nrol@bis.gov.in

Scope List

Reset

297 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 21 (1992)

Wrought aluminium and aluminium alloys for manufacture of utensils specification (Fourth Revision)

Rs.6600/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2, Table 2 of IS:21 (Designation & Condition 64430, WP') (Tensile Strength)	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, WP') (Bend Test (Radius of Bend))	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, WP') (Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, WP') (Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, WP') (Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, WP') (Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-

-
Excluding Microalloying elements and proof stress

IS 318 (1981)

Specification for leaded tin bronze ingots and castings (Second Revision)

Please see remarks View breakup
Grades LTB1, LTB2, LTB3 & LTB5 - Rs.1650.00 for Casting Rs.1500.00 for Ingots, Grades LTB4 & LTB 6 - Rs.1425.00 for Casting Rs.1350.00 for Ingots

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7 (SIZE AND SHAPE)	-
6 (FREEDOM FROM DEFECTS)	-
4, Table 2. (MECHANICAL PROPERTIES)	-
7.2 (Dimension)	-
7.1 (Mass)	-
6.2 (Freedom from defects-Castings)	-
6.1 (Freedom from defects-Ingots)	-
4.1, Table 2 (Elongation)	-
4.1, Table 2 (Tensile strength)	-

-
Excluding Proof test, Microalloying elements

IS 15410 (2003)

Containers for packaging of natural mineral water and packaged drinking water - Specification

Total charges = Rs.5850.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.0 (chem) (MATERIAL)	-
4.1 (chem) (Workmanship and Finish)	-
4.2 (chem) (Design, Shape & Dimension)	-
4.2 (chem) (a) Peelability)	-
4.3 (chem) (Workmanship, Finish & Appearance)	-
4.4 (chem) (Brimful capacity)	-
4.5 (chem) (a) Wall Thickness, mm Top)	-
4.5 (chem) ((b) Wall Thickness, mm Middle)	-
4.6.3 (chem) (Leakage Test a) Closures leakage test)	-
4.6.3 (chem) (b) Vibration leakage test)	-
4.6.4 (chem) (Drop Test)	-
4.6.5.1.a (Colour migration Test (Container))	-
4.6.5.1.b (Colour migration Test (Cap))	-
4.6.5 (chem) (c. Colour Migration (Cap))	-
4.6.6.a (chem) (Water Potability Test (a) Odour)	-
4.6.6.b (chem) (Water Potability Test (b) Taste)	-
4.5 (chem) ((c) Wall Thickness, mm Bottom)	-
4.6.3 (chem) (c) Air pressure leakage test)	-
4.6.2 (chem) (Transparency,)	-
Cl. 4.6.5 (chem) (Cl. 4.6.5 Overall migration (Caps))	-
4.6.5.1 (chem) (Colour migration (Container))	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (i) (Barium)	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (ii) (Cobalt)	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (iii) (Copper)	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (iv) (Iron)	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (v) (Lithium)	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (vi) (Manganese)	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (vii) (Zinc)	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (viii) (Antimony)	-
CL 4.6.7.2 and 4.6.7.3, Table 3 (ix) (Phthalic acid, bis(2-ethylhexyl) ester (DEHP))	-

-
-

IS 10500 (2012)

Drinking water - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4. SL No.i)of Table I (Colour)	-
4.SL No.ii) of Table I (Odour)	-
4.SL No.iii)of Table I (pH)	-
4.SL No.v)of Table I (Turbidity, NTU, Max)	-
4.SL No.vi)of Table I (Total dissolved solids, mg/l, max)	-
table 2 sl.no 1 ( Aluminium (as Al), mg/l, Max)	-
table 2 sl.no 2 (Ammonia (as total ammonia-N), mg/l, Max)	-
table 2 sl.no 3 (Anionic detergents (as MBAS), mg/l, Max)	-
table 2 sl.no 4 (Barium (as Ba), mg/l, Max)	-
table 2 sl.no 5 (Boron (as B), mg/l, Max)	-
table 2 sl.no 6 (Calcium (as Ca), mg/l, Max)	-
table 2 sl.no 9 (Copper (as Cu), mg/l, Max)	-
table 2 sl.no 10 ( Fluoride (as F) mg/l, Max)	-
table 2 sl.no 11 (Free residual chlorine, mg/l, Min)	-
table 2 sl.no 12 (Iron (as Fe), mg/l, Max)	-
table 2 sl.no 13 (Magnesium (as Mg), mg/l, Max)	-
table 2 sl.no 14 (Manganese (as Mn), mg/l, Max)	-
table 2 sl.no 15 (Mineral oil, mg/l, Max)	-
table 2 sl.no 16 (Nitrate (as NO3), mg/l, Max)	-
table 2 sl.no 17 (Phenolic compounds (as C6H5OH), mg/l, Max)	-
table 2 sl.no 18 (Selenium (as Se), mg/l, Ma)	-
table 2 sl.no 19 (Silver (as Ag), mg/l, Max)	-
table 2 sl.no 20 (Sulphate (as SO4) mg/l, Max)	-
table 2 sl.no 21 (Sulphide (as H2S), mg/l, Max)	-
table 2 sl.no 22 (Total alkalinity as calcium carbonate, mg/l, Max)	-
table 2 sl.no 23 (Total hardness (as CaCO3 mg/l, Max)	-
table 2 sl.no 24 (Zinc (as Zn), mg/l, Max)	-
TABLE 3 sl no 1 (Cadmium (as Cd), mg/l, Max)	-
TABLE 3 sl no 3 (Lead (as Pb), mg/l, Max)	-
TABLE 3 sl no 4 (Mercury (as Hg), mg/l, Max)	-
TABLE 3 sl no 5 ( Molybdenum (as Mo), mg/l, Max)	-
TABLE 3 sl no 6 (Nickel (as Ni), mg/l, Max)	-
TABLE 3 sl no 7 (Pesticides, µg/l, Max)	-
TABLE 3 sl no 8 (Polychlorinated biphenyls, mg/l,)	-
TABLE 3 sl no 9 (Polynuclear aromatic hydro-carbons (as PAH), mg/l, Max)	-
TABLE 3 sl no 10 (Total arsenic (as As), mg/l, Max)	-
TABLE 3 sl no 11 (Total chromium (as Cr), mg/l, Max)	-
TABLE 5 sl no 1 (Alachlor)	-
TABLE 5 sl no 3 (Atrazine)	-
TABLE 5 sl no 4 ( Alpha HCH)	-
TABLE 5 sl no 5 (Beta HCH)	-
TABLE 5 sl no 6 (Butachlor)	-
TABLE 5 sl no 7 (Chlorpyriphos)	-
TABLE 5 sl no 8 (Delta HCH)	-
TABLE 5 sl no 9 (2,4- Dichlorophenoxyacetic acid)	-
TABLE 5 sl no 10 ( DDT (o, p and p, p – Isomers of DDT, DDE and DDD))	-
TABLE 5 sl no 11 (Endosulfan (alpha, beta, and sulphate))	-
TABLE 5 sl no 12 ( Ethion)	-
TABLE 5 sl no 13 (Gamma — HCH (Lindane))	-
TABLE 5 sl no 14 ( Isoproturon)	-
TABLE 5 sl no 15 (Malathion)	-
TABLE 5 sl no 16 (Methyl parathion)	-
TABLE 5 sl no 17 (Monocrotophos)	-
TABLE 5 sl no 18 (Phorate)	-

-
Excluding chloramines, cyanide, trihalomethanes

IS 1806 (2018)

Malted milk foods - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.3-Table 1- ix (Bacterial count)	-
4.3-Table 1- x (Coliform count)	-
4.3-Table 1- xi (E. coli)	-
4.3-Table 1- xii (Yeast and mould count)	-
4.3-Table 1- xiii (Salmonella)	-
4.3-Table 1- xiv (Shigella)	-
4.3-Table 1- xv (Vibrio cholerae )	-
4.3-Table 1- xv ( V. parahaemolyticus)	-
4.3-Table 1- xvi (Faecal streptococci )	-
4.3-Table 1- xvi ( Staphylococcusaureas)	-

-
Excluding moisture, Cocoa Powder

IS 11952 (1986)

Specification for steels for piston pins (Gudgeon Pins)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1,4.2 Table 1 (Carbon-Relevant parts of IS 228)	-
4.1,4.2 Table 1 (Silicon-Relevant parts of IS 228)	-
4.1,4.2 Table 1 (Manganese-Relevant parts of IS 228)	-
4.1,4.2 Table 1 (Sulphur-Relevant parts of IS 228)	-
4.1,4.2 Table 1 (Phosphorous-Relevant parts of IS 228)	-

-
Excluding Grain size, surface defect, Cr, Ni, Mo, Nb, V, Ti, B

IS 10 : Part 4 (1989)

Plywood tea - Chests - specification: Part 4 metal fittings

Rs 225/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (MATERIAL)	-
4.1 (Thickness)	-
4.2 (Width)	-
4.3 (Length)	-
4.3.1, 4.3.3, Table 1 (Size of Tea-chest)	-
4.3.1, 4.3.3, Table 1 (Length, corners)	-
4.3.1, 4.3.3, Table 1 (Length, top and bottom)	-
4.3.1, 4.3.3, Table 1 (Position of V notch)	-
4.3.4 (tea-chest ofsize 380 mm X 685 mm x 845 mm, For corners)	-
4.3.4 (tea-chest ofsize 380 mm X 685 mm x 845 mm, For top and bottom)	-

-
Test facility is complete

IS 319 (2007)

Free cutting brass bars, rods and section - Specification (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.0 (Freedom from defects)	-
7.0 (Dimension and Tolerances)	-
9.1 Table-2 (Tensile Strength)	-
9.1 Table-2 (Elongation)	-
9.2 (Vickers Hardness)	-
10.1 (Mercurous Nitrate Test)	-

-
Excluding Microalloying Elements

IS 916 (2000)

Square tins for solid products - Specification (Fourth Revision)

4950 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.3.1.1 (Tin Coating Thickness)	-
4.2 (Dimension and Tolerances)	-
4.3.2 (Handle wire diameter)	-
4.4.1 (Body)	-
4.4.2 (Sides)	-
4.4.3 (Top and Bottom)	-
4.1 (Capacity)	-
5.1 (Air-Pressure Test)	-
5.2 (Handle Pull Test)	-
4.2 (Dimension and Tolerances)	-

-
Chemical: Excluding Cu, Tin, Antimony Mechanical: Test facility is complete

100

IS 915 (2012)

Laboratory glassware - One - Mark volumetric flasks (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Table 1 (Nominal Capacity)	-
Table 1 (Internal Neck Diameter)	-
Table 1 (Distance of graduation line)	-
Table 1 (Overall Height)	-
Table 1 (Bulb Diameter)	-
Table 1 (Base Diameter)	-
Table 1 (Wall Thickness)	-
8.3 (Shape)	-
8.4 (Neck)	-
8.5 (Stopper)	-
9.0 (Graduation Line)	-

-
Excluding Accuracy test and material tests

101

IS 3196 : Part 1 (2013)

Welded low carbon steel cylinders exceeding 5 litres water capacity for low pressure liquefiable gases: Part 1 cylinders for liquefied petroleum gases (Lpg) - Specification (Sixth Revision)

14900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
10 (Foot Ring)	-
14 (Bung)	-
9 (Valve Protection)	-
14 (Water Capacity)	-
15 (Hydrostatic Test)	-
16 (Pneumatic Leakage Test)	-
17 (Fatigue Test)	-
17 (Burst Test under Hydraulic Pressure)	-
18 (Parent Metal Longitudinal Tensile Strength)	-
18 (Parent Metal Circumferential Tensile Strength)	-
18 (Parent Metal Longitudinal Tensile Strength)	-
18 (Parent Metal Circumferential Tensile Strength)	-
18 (Weld Metal Tensile Strength)	-
18 (Bend Test across weld)	-
18 (Root Bend Test)	-
18 (Face Bend Test)	-
18 (Minimum Thickness Test)	-
23.2 (Protective Coatings)	-
18 (Macro Examination)	-
20.0 (Marking)	-

-
Up to 45 litre water capacity- All tests except Radiographic Examination as per clause 13 (for steel as per IS 15914 additional test as per clause 19 facility not available), Above 45 litre water capacity - All test except Pneumatic leakage test as per clause 16, Static loading test as per clause 10, Drop test as per clause 9.3.4 and Radiographic Examination as per clause 13 (for steel as per IS 15914 additional test as per clause 19 facility not available)

102

IS 16720 (2018)

Pulverized Fuel Ash-Cement Bricks- Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 and fig.1A &1B (Dimensions- Length (L) )	-
4.1 and fig.1A &1B (Dimensions- Width (B) )	-
4.1 and fig.1A &1B (Dimensions- Height (H))	-
4.1 & 4.3 and fig.1A &1B (Dimensions - Depth)	-
4.1 and fig.1A &1B (Dimensions)	-
8.1 (GENERAL)	-
8.3 (Density Annex C of IS 2185 (Part 1))	-
8.4 and Table 1 (Compressive Strength - Individual IS 3495 (Part 1))	-
8.4 and Table 1 (Compressive Strength - Average IS 3495 (Part 1))	-
8.6 (Water Absorption IS 3495 (Part 2))	-
8.5 (Drying Shrinkage IS 4139)	-

-
Complete

103

IS 3601 (2006)

Steel tubes for mechanical and general engineering purposes - Specification (Second Revision)

2000/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.0 (Workmanship)	-
8.0 (Straightness)	-
11.1 (Surface Protection)	-
11.2 (Surface Protection)	-
19.1.1, 24.1.1, 28.1.1, 33.1.1 (Dimensions- Outside Dia)	-
19.1.2, 24.1.2, 28.1.2, 33.1.2 (Dimensions- Thickness)	-
13.1.3 (Tensile Strength)	-
13.1.1 (Yield Stress)	-
13.1.2 (Elongation)	-
13.2 (Flattening Test)	-
13.3 (Bend Test (Strip))	-
13.6 (Crush Test)	-
19.1.3 (Height of Internal Fin)	-
11.1 (Surface Protection)	-
11.2 (Surface Protection)	-
4.1 (Sulphur-Percentage by mass)	-
4.1 (Phosphorus-Percentage by mass)	-
13.4 (Bend Test (Whole Tube))	-
16 (Marking)	-
Cl. 10 Annex B Cl. 17, Cl. 19 (Mass)	-
4.0 (c) (Micro Alloying elements (Nb+V+Ti))	-
4.0 (f) (Nitrogen content)	-
4.0 (a) (Carbon as C - IS:8811)	-
4.0 (b) (Manganese as Mn - IS:8811)	-

-
Test facility is complete

104

IS 15914 (2011)

High tensile strength flat rolled steel plate (Up To 6 Mm), sheet and strip for the manufacture of welded gas cylinder - Specification

Rs. 7760/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 7 (UTM)	-
Cl 9 (Workmanship)	-
Cl 10 (Length, Width & Thickness)	-
6.0 (CARBON)	-
6.0 (SULPHUR)	-
6.0 (SILICON)	-
6.0 (MANGANESE)	-
6.0 (PHOSPHORUS)	-
6.0 (NITROGEN)	-

-
Excluding Microalloying Elements

105

IS 878 (2008)

Laboratory glassware - Graduated measuring cylinders (Second Revision)

Rs.4200/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Table-1 (Nominal capacity)	-
Table-1 (Overall height)	-
Table-1 (Distance from top of scale to top of cylinder)	-
Table-1 (Internal height to highest graduation line)	-
Table-1 (Sub-divisions)	-
Table-1 (capacity at lowest graduation line)	-

-
Excluding Accuracy test and material test

106

IS 10908 (1991)

Flexible rubber tubing for liquefied petroleum gas - Specification (First Revision)

7800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.4.1 (The tubing made out of this material shall be green in colour )	-
Cl.4.2 (The walls shall be seamless and free from all visible such as lumps, blows-holes,cracks etc and the bore shall be clean and free from loose particles which might be carried forward by the gas)	-
Cl4.3.1 (The tubing shall be supplied in 6.4 and 7.0 mm inisde diametre,The tolerance on nominal diamtere shall be as per table 1)	-
Cl4.3.2 (it shall comply with the thickness as givien in table 1 when measured according to 4.2.2 of IS 443;1975 The readings shall be taken from different sample sections.)	-
Cl.4.4,(Cl.4.4.1) (when tested in accordance with the method given in AnnexureA. It shall fit over the standard and oversize metal nozzle shown in Fig1,2 and 3)	-
Cl.4.4,(Cl.4.4.2) (it shall remain atatched to both nozzles throught the test period)	-
Cl.4.5 (When immersed in water for 5 minutes under an internal air pressure of 0.25 Mpa or 250kPa (2.5 bar), the increase in the outside diametre of the tubing ,Also the same shall not burst when the pressure is increasded to 0.5 Mpa or 500 kpa (5 bar0, The test shall be carried out on a lengtj of 60 cm.)	-
Cl.4.5 (When immersed in water for 5 minutes under an internal air pressure of 0.25 Mpa or 250kPa (2.5 bar), the same shall not burst when the pressure is increasded to 0.5 Mpa or 500 kpa (5 bar0, The test shall be carried out on a lengtj of 60 cm.)	-
Cl.4.9 (Crushing test , )	-
Cl.4.6 (Shore Hardness: the hardnesss on the flatsurface of the cut/slit tubing shall be measured and the same shall be 60 ± 5˚A)	-
Cl.4.7 (Accelerated Ageing test, the flexible tubing or suitable portion of the tubing shall be subjected to accelerated ageing at a temperature of 100Deg Cfor 72 hours in accordance with the method prescribed in IS 3400 (Part 4) it shall not show a change of + 10 A of its orignal shore hardness )	-
Cl.4.8.1 (Flexible test , Annexure B The gas pressure shown on the manometre shall not drop by more than 1 Kpa)	-
Cl4.8.2 (The tubing shall be so flexible that it will make contact with a cylinder former of radius 68 mm for at least 110 deg of its circumference when the tubing is placed over the framer and a mass of 1.6 kg is attcahed to each end)	-
Cl.4.10 (Resistance to lpg ,Annexure c Shall not be more than 15 % of the initial mass of the tubing and the amount of exctractable matter shall not excced 10 percent of the iniital mass of te tubing)	-
Cl.4.11 (Resistance to Ozone ,Annexure D Shall not show any breakage on surface or crack or defects)	-
Cl.4.12 (Burning behaviour on exposure to small flame,Annexure E tubing shall not burn to either of the outer marks within the test period of 45 seconds)	-

-
Excluding Resistance to Ozone, Resistance to LPG, Accelerated Ageing test flexibilty test, thickness and hardness

107

IS 1835 (1976)

Specification for round steel wire for ropes (Third Revision)

Rs 4500/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 3 (Manufacturing )	-
Cl 7 (Workmanship)	-
Cl 8 (Manufacturing )	-
Cl 10 (Diameter)	-
Cl 11.2 (Workmanship)	-
Cl 12.2 (UTM)	-
Cl 12.3 (Torsion)	-
Cl 12.4 (Reverse Bend)	-
Cl 12.5 (Wrap)	-
Cl 12.6 (Adhesion )	-
Cl 11.3 (Coating Test)	-
Cl. 9.1, T-3 (Mass of Zinc Coating)	-
Cl. 9.1, T-3 (Uniformity)	-
Cl. 5.1, T-1 (C)	-
Cl. 5.1, T-1 (Mn)	-
Cl. 5.1, T-1 (Si)	-
Cl. 5.1, T-1 ( Grade 1) (P)	-
Cl. 5.1, T-1 ( Grade 1) (S)	-
Cl. 5.1, T-1 ( Grade 5) (Cr)	-
Cl. 5.1, T-1 ( Grade 1) (Cu)	-
Cl. 5.1, T-1 ( Grade 2) (Cu)	-
Cl. 5.1, T-1 ( Grade 3) (Cu)	-
Cl. 5.1, T-1 ( Grade 4) (Cu)	-
Cl. 5.1, T-1 ( Grade 5) (Cu)	-
Cl. 5.1, T-1 ( Grade 1) (Ni)	-
Cl. 5.1, T-1 ( Grade 2) (Ni)	-
Cl. 5.1, T-1 ( Grade 3) (Ni)	-
Cl. 5.1, T-1 ( Grade 4) (Ni)	-
Cl. 5.1, T-1 ( Grade 5) (Ni)	-

-
Excluding Microalloying Elements for the wire having diameter below 4mm

108

IS 3954 (1991)

Hot Rolled Steel Channel Sections for General Engineering Purposes - Dimensions

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4, 6.1, Table 1 (CHG 16, Mass)	-
4, 6.1, Table 1 (CHG 16, Depth of channel)	-
4, 6.1, Table 1 (CHG 16, Width of flange)	-
4, 6.1, Table 1 (CHG 16, Thickness of web)	-
4, 6.1, Table 1 (CHG 16, Thickness of flange)	-
4, 6.1, Table 1 (CHG 16, Radius at root)	-
4, 6.1, Table 1 (CHG 16, Radius at toe)	-
4, 6.1, Table 1 (CHG 16, Centre of gravity)	-
4, 6.1, Table 1 (CHG 16, Slope of flange)	-
4, 6.1, Table 1 (CHG 20, Mass)	-
4, 6.1, Table 1 (CHG 20, Depth of channel)	-
4, 6.1, Table 1 (CHG 20, Width of flange)	-
4, 6.1, Table 1 (CHG 20, Thickness of web)	-
4, 6.1, Table 1 (CHG 16, Thickness of flange)	-
4, 6.1, Table 1 (CHG 20, Slope of flange)	-
4, 6.1, Table 1 (CHG 20, Radius at root)	-
4, 6.1, Table 1 (CHG 16, Radius at toe)	-
4, 6.1, Table 1 (CHG 20, Centre of gravity)	-
4, 6.1, Table 1 (CHG 40, Mass)	-
4, 6.1, Table 1 (CHG 40, Depth of channel)	-
4, 6.1, Table 1 (CHG 40, Width of flange)	-
4, 6.1, Table 1 (CHG 40, Slope of flange)	-
4, 6.1, Table 1 (CHG 40, Radius at root)	-
4, 6.1, Table 1 (CHG 16, Radius at toe)	-
4, 6.1, Table 1 (CHG 40, Centre of gravity)	-

-
Test facility is complete

109

IS 1264 (1997)

Brass gravity die castings - Specification (Fourth Revision)

1435.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.0 (Freedom from defects)	-
6.0 (Size)	-
6.0 (Mass)	-
9.0 (Pressure test)	-

-
Facility for Chemical tests not available

110

IS 6760 (1972)

Specification for slotted countersunk head wood screws

Rs.900.0 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1, Table 1 (Diameter of Unthreaded Shank d, Nominal)	-
3.1, Table 1 (Diameter of Unthreaded Shank d, maximum)	-
3.1, Table 1 (Diameter of Unthreaded Shank d, Minimum)	-
3.1, Table 1 (V*)	-
3.1, Table 1 (Pitch)	-
3.1, Table 1 (Diameter of Head, D, Maximum)	-
3.1, Table 1 (Diameter of Head, D, Minimum)	-
3.1, Table 1 (Depth of Head c†, maximum)	-
3.1, Table 1 (Depth of Head c†, minimum)	-
3.1, Table 1 (Width of Slot s, maximum)	-
3.1, Table 1 (Width of Slot s, minimum)	-
3.1, Table 1 (Depth Slot n‡, Maximum)	-
3.1, Table 1 (Depth Slot n‡, Mainimum)	-

-
-

111

IS 274 : Part 1 and 2 (1981)

Specification for shovels: Part 1 genral purpose shovels: Part 2 heat - Treated shovels (Third Revision)

Rs 600/, Rs 675/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5 Table-1,2 (Shape)	-
5 Table-1,2 (Dimensions- A)	-
5 Table-1,2 (Dimensions- B)	-
5 Table-1,2 (Dimensions- C)	-
5 Table-1,2 (Dimensions- D)	-
5 Table-1,2 (Dimensions- E)	-
5 Table-1,2 (Dimensions- G)	-
5 Table-1,2 (Dimensions- H)	-
5 Table-1,2 (Dimensions- K)	-
5 Table-1,2 (Dimensions- L)	-
6.1 (Blade thickness)	-
7.0 (Mass)	-
8.0 (Manufacture)	-
8.0 (Manufacture)	-
8.0 (Manufacture)	-
9.1 (Handles)	-
9.3 (Handles)	-
11.0 (Workmanship & Finish )	-
12.0 (Preservative Treatment )	-
4.1 (Sulphur)	-
4.1 (Phosphorus)	-

-
Excluding Microalloying Elements

112

IS 2039 : Part 1 to 3 (1991)

Steel tubes for bicycle and cycle rickshaws - Specification (Second Revision)

Rs.4320.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 6.1 (Workmanship)	-
Cl. 6.2 (Fin Height)	-
Cl. 6.3 (Straightness)	-
Cl. 8.1 (Tensile Strength)	-
Cl. 8.1 (Yield Strength)	-
Cl. 8.1 (Elongation)	-
Cl. 8.2 (Drift Expansion Test- IS 2335)	-
Cl. 8.3 (Flattening Test-IS 2338)	-
Cl. 9 (Diameter)	-
Cl. 9 (Thickness)	-
Cl. 3.2.1, Table 4 (Yield Stress)	-
Cl. 3.2.1, Table 4 (UTS)	-
Cl. 3.2.1, Table 4 (Elongation)	-
Cl. 3.2.2, Table 2 (Drift Expansion Test- IS 2335)	-
Cl. 3.2.3, Table 3 (Flattening Test-IS 2338)	-
Cl. 4.2.1 (Diameter)	-
Cl. 4.2.2 (Thickness)	-
Cl. 4.2.3 (Length)	-
Cl. 4.2.1, Table 7 (Yield Stress)	-
Cl. 4.2.1, Table 7 (UTS)	-
Cl. 4.2.1, Table 7 (Crushing)	-
Cl. 4.2.2, Table 8 (Drift Expansion Test- IS 2335)	-
Cl. 4.2.3, Table 9 (Flattening Test-IS 2338)	-
Cl. 5.2.1, Table 10 (Diameter)	-
Cl. 5.2.2 (Mean Thickness)	-
Cl. 5.2.3, Table 6 (Length)	-
Cl. 5.1 Table 1 (Carbon)	-
Cl. 3.1 (Sulphur)	-
Cl. 3.1 (Phosphorous)	-
Cl. 3.1 (Manganese)	-
Cl. 3.1 (Silicon)	-

-
-

113

IS 5135 : Part 2 (1994)

Specification for hand rotary duster: Part 2 shoulder mounted type (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.0 (Capacity)	-
8.0 (WORKMANSHIP AND FINISH)	-

-
-

114

IS 4366 : Part 2 (1985)

Specification for agricultural tillage discs: Part 2 flat type (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.0 (HARDNESS)	-
5.1, Table 1 (Nominal size)	-
5.1, Table 1 (Thickness)	-
5.2, Table 2 (Dimension)	-
5.2, Table 2 (Tolerance)	-
6.0 (HOLE TYPES)	-
7.1 (Central Hole)	-
7.2 (Pitch Circle Diameter -)	-
7.3 (Fixing Holes)	-
7.4, Table 3 (Nominal Size)	-
7.4, Table 3 (Thickness)	-
7.4, Table 3 (Centre hole diameter)	-
7.4, Table 3 (Pitch circle diameter)	-
7.4, Table 3 (No. Of holes)	-
8.1 (distortion)	-
8.2 (eccentricity)	-
8.3 (thickness of the cutting edge)	-
8.4 (cutting edge of discs)	-
9.0 (DESIGNATION)	-
10.0 (WORKMANSHIP AND FINISH)	-

-
Test facility is complete

115

IS 5135 : Part 1 (1994)

Specification for hand - Rotary duster: Part 1 belly - Mounted type (Second Revision)

Testing charges for the product are Rs 7600/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.0 (Capacity)	-
8.0 (WORKMANSHIP AND FINISH)	-

-
Test facility not availabe

116

IS 2326 (1987)

Automatic Flushing Cisterns for Urinals (Other than Plastic Cisterns)

1275 incl endu test + material as per ISS View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.0 (NOMINAL SIZE)	-
4.2 (Cistern )	-
4.3 (Depth of Cistern Body)	-
4.4 (Siphonic Apparatus)	-
4.5 (Lid and Cover)	-
4.6 (Feeding Device -)	-
5.0 (FINISH)	-
6.1 (a) (Urinal Delivering capacity)	-
6.1 (b) (Flushing)	-
6.1 (c) (Discharge)	-

-
Complete for Chemical, test facility not available for mechanical

117

IS 513 : Part 1 (2016)

Cold reduced carbon steel sheet and strip: Part 1 cold forming and drawing purpose (Sixth Revision)

Rs.8850/- Excluding Tensile Strain Hardening component View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8 (Mechanical and Physical Properties)	-
Cl 8 (UTM)	-
Cl 9 (Workmanship)	-
Cl 10 (Workmanship)	-
Cl 11 (Length, Width & Thickness)	-
7.0 (CARBON)	-
7.0 (SULPHUR)	-
7.0 (SILICON)	-
7.0 (MANGANESE)	-
7.0 (PHOSPHORUS)	-
7.0 (NITROGEN)	-
Cl. 11 (Out of square)	-
Cl. 11 (Flatness)	-
Cl. 11 (Camber)	-
Cl. 11 (Width)	-
Cl. 11 (Thickness)	-
Cl. 8.4 (Bend Test)	-
Cl. 8.3 Table 6 (Hardness Test ( Only for CR0 & CR1))	-
Cl. 8.1 & Table 5A, 5B & 5C (Elongation at 80 mm gauge length)	-
Cl. 8.1 & Table 5A, 5B & 5C (Elongation at 50 mm gauge length)	-
Cl. 8.1 & Table 5A, 5B & 5C (Yield Stress)	-
Cl. 9 Table 8 (Surface roughness)	-
7.0 (ALUMINIUM)	-
7.0 (MICRO ALLOYS)	-

-
Excluding Finish (9.5),

118

IS 739 (1992)

Wrought aluminium and aluminium alloys - Wire for general engineering purposes - Specification (Third Revision)

Rs.225/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.0 (Freedom from defects)	-
7.0 (Dimension and Tolerances)	-
9.1 (Tensile Strength)	-
9.3 (Wrapping Test)	-
6.0 (Freedom from defects)	-
15.4 (b) (Cold impact)	-
9.1 (PIPE ENDS)	-
6.0 (Freedom from defects)	-
15.4 (b) (Cold impact)	-
9.1 (PIPE ENDS)	-

-
Facility for Chemical tests not available

119

IS 4366 : Part 1 (1985)

Specification for agricultural tillage discs: Part 1 concave type (Second Revision)

Rs 675/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.0 (MATERIAL)	-
5.0 (HARDNESS)	-
6.1, Table 1 (Nominal Size)	-
6.1, Table 1 (Thickness)	-
6.1, Table 1 (Concavity)	-
6.2, Table 2 (DISC SIZE)	-
6.2, Table 2 (EQUALLY SPACED NOTCH NUMBERS)	-
6.2, Table 2 (Notch Width)	-
6.2, Table 2 (Notch depth)	-
6.3, Table 3 (A)	-
6.3, Table 3 (M)	-
6.3, Table 3 (N)	-
6.3, Table 3 (P)	-
6.4 (Dimension)	-
7.0 (HOLE TYPES)	-
8.1 (Centre Square Hole)	-
8.2 (Circular Centre Hole with Keyway)	-
8.3 (Several Fixing Holes With or Without Circular Centre Hole)	-
9.1 (eccentricity and wobble)	-
9.2 (permanent deflection)	-
9.4 (thickness of the cutting edge)	-
8.4, Table 5 (DISC SIZE)	-
8.4, Table 5 (CENTRE SQUARE HOLE SIZE)	-
8.4, Table 5 (CENTRE Circular HOLE SIZE)	-
8.4, Table 5 (With bolt fixing, Centre hole diameter)	-
8.4, Table 5 (With bolt fixing, Pitch Circle Diameter)	-
8.4, Table 5 (With bolt fixing, Fixing hole size)	-
8.4, Table 5 (With bolt fixing, No. Of holes)	-
8.4, Table 5 (With rivet fixing, Centre hole diameter)	-
8.4, Table 5 (With rivet fixing, Pitch Circle Diameter)	-
8.4, Table 5 (With bolrivet fixing, Fixing hole size)	-
8.4, Table 5 (With rivet fixing, No. Of holes)	-
9.1, Table 6 (Nominal size)	-
9.1, Table 6 (ECCENTRICITY)	-
9.1, Table 6 (Wobble)	-
9.5 (cutting edge of the disc)	-
9.6 (Radius of concavity)	-
9.7 (Square holes)	-
9.8 (crown of the keyway)	-
9.9 (fixing holes)	-
10.0 (DESIGNATION)	-
11.0 (WORKMANSHIP AND FINISH)	-

-
Test facility is complete

120

IS 737 (2008)

Wrought aluminium and aluminium alloy sheet and strip for general engineering purposes - Specification (Fourth Revision)

Rs 8750/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.0 (Freedom from defects)	-
7 Table-2 (Tensile Strength)	-
7 Table-2 (Elongation)	-
7 Table-2 (Bend Test)	-
9.1 (PIPE ENDS)	-
15.4 (b) (Cold impact)	-

-
Excluding Proof stress, Facility for Chemical tests not available

First
Prev
3
4
5
6
Next
Last

Bureau of Indian Standards

The National Standards Body of India

BIS, Northern Regional Laboratory (NRL)

B-69, Industrial Focal Point, Phase VII, Mohali, Mohali, S.A.S Nagar, Punjab, 160059

- nrol@bis.gov.in

Scope List